Understanding the AWS A5.x Filler Metal Specification Series A Comprehensive Study Guide for Welding Students, CWI Candidates, and Fabrication Professionals The American Welding Society (AWS) publishes a family of specifications under the A5.x designation that classify filler metals used in all major welding processes. These specifications are referenced by every major construction code including AWS D1.1 (structural steel), ASME Section IX (pressure vessels and piping), and API 1104 (pipelines). Understanding how to read and interpret these classifications is essential for welders, inspectors, and engineers. This study guide covers the most commonly used A5.x specifications, explains the classification system for each, and provides the key data tables that appear on certification exams and are used daily in fabrication shops. All information is based on publicly available AWS classification conventions and general industry knowledge. 1. How the AWS Classification System Works Every AWS filler metal classification encodes critical information into a short alphanumeric string. The system was designed so that a welder or inspector can look at a classification printed on an electrode box or wire spool and immediately know the tensile strength class, welding positions, type of coating or shielding, and current type. Each digit and letter has a specific meaning defined by the applicable A5.x specification. For example, the classification E7018 tells you: E = Electrode, 70 = minimum 70,000 psi tensile strength, 1 = all welding positions, 8 = low-hydrogen potassium coating with iron powder, AC or DCEP current. Similarly, ER70S-6 tells you: E = Electrode, R = also usable as a Rod, 70 = minimum 70 ksi tensile, S = Solid wire, 6 = specific chemistry variant (higher silicon and manganese for better deoxidation). The key principle is that the classification is a GUARANTEE of minimum performance. An E7018 electrode from any manufacturer in the world must meet the same minimum tensile strength, yield strength, elongation, and impact requirements defined in AWS A5.1. This interchangeability is what makes the system work across the global welding industry. 2. Carbon Steel SMAW Electrodes (AWS A5.1) AWS A5.1 is one of the oldest and most widely referenced filler metal specifications, covering carbon steel covered electrodes for Shielded Metal Arc Welding (SMAW), commonly called 'stick welding'. The specification defines classifications for electrodes ranging from 60 ksi to 70 ksi minimum tensile strength. Classification Breakdown: E X X X X • • • • E = Electrode (consumable, conducts current) First two digits = Minimum tensile strength in ksi (60 = 60,000 psi, 70 = 70,000 psi) Third digit = Welding position: 1 = all positions, 2 = flat and horizontal fillet only Fourth digit = Coating type and current: determines usability characteristics Classification Tensile (ksi) Coating Type Positions Current Primary Application E6010 60 min High cellulose sodium All DCEP Root passes in pipe welding, penetration E6011 60 min High cellulose potassium All AC/DCEP Same as E6010 but works on AC machines E6013 60 min High titania potassium All AC/DC Sheet metal, light structural, beginners E7014 70 min Iron powder titania All AC/DC General purpose, smooth bead appearance E7018 70 min Low-H potassium + iron powder All AC/DCEP Structural code work, most widely used E7024 70 min Iron powder titania (heavy) Flat/H-fillet AC/DC High deposition rate, flat position only E7048 70 min Low-H potassium + iron powder All + V-down AC/DCEP Vertical-down low hydrogen welding Why E7018 dominates: E7018 is the most commonly specified electrode in structural welding worldwide. Its low-hydrogen coating minimizes the risk of hydrogen-induced cracking (also called cold cracking or delayed cracking), which is the most common weld defect in structural steel. AWS D1.1 requires low-hydrogen electrodes for most prequalified WPS applications on steels with yield strength above 60 ksi. The '-1' suffix (E7018-1) indicates improved toughness at -50F, used for low-temperature service. 3. Carbon Steel GMAW/GTAW Electrodes (AWS A5.18) AWS A5.18 covers solid wire electrodes and rods for Gas Metal Arc Welding (GMAW, commonly called 'MIG welding') and Gas Tungsten Arc Welding (GTAW, commonly called 'TIG welding'). Classification is based on the chemical composition of the electrode (for solid wires) and the mechanical properties and chemistry of the deposited weld metal. Classification Breakdown: ER XX S - X • • • • E = Electrode (can carry current in GMAW), R = Rod (can be used as filler rod in GTAW) XX = Minimum tensile strength in ksi divided by 10 (70 = 70,000 psi) S = Solid wire (as opposed to composite/metal-cored) Last digit = Chemistry variant (2, 3, 6, 7, G, etc.) Classification Tensile C % Mn % Si % Shielding Gas Key Characteristics ER70S-2 70 ksi 0.07 max 0.90-1.40 0.40-0.70 Ar or Ar/CO2 ER70S-3 70 ksi 0.06-0.15 0.90-1.40 0.45-0.75 CO2 or Ar/CO2 General purpose, requires clean base metal ER70S-6 70 ksi 0.06-0.15 1.40-1.85 0.80-1.15 CO2 or Ar/CO2 Highest deoxidation, tolerates mill scale Triple deoxidized (Ti+Zr+Al), cleanest weld Why ER70S-6 is king: ER70S-6 accounts for roughly 80% of all GMAW solid wire consumed in North America. Its high silicon (0.80-1.15%) and manganese (1.40-1.85%) content makes it a strong deoxidizer, meaning it tolerates light mill scale, surface rust, and slightly contaminated base metal better than the S-2 or S-3 variants. The tradeoff is slightly higher weld metal silicon content, which can affect toughness in multi-pass welds on thick plate — but for single-pass and light structural work, it is the industry default. 4. Flux Cored Arc Welding Electrodes (AWS A5.20 / A5.29 / A5.36) Flux Cored Arc Welding (FCAW) uses tubular wire electrodes filled with flux. The flux provides shielding, deoxidation, and slag formation — similar to the coating on a stick electrode but delivered through a continuous wire feed. FCAW is divided into gas-shielded (requires external CO2 or Ar/CO2) and self-shielded (no external gas needed). AWS A5.20 covers carbon steel, A5.29 covers low-alloy steel, and A5.36 is the newer unified specification that combines both into an open classification system. Classification Tensile Shield Gas PositionsCurrent Primary Application E71T-1C 70 ksi 100% CO2 All DCEP Structural fabrication, shipbuilding, high deposition E71T-1M 70 ksi 75-80% Ar/CO2 All DCEP Same applications but cleaner bead, less spatter E71T-8 70 ksi Self-shielded All DCEN Field erection, outdoor work, no gas bottles needed E81T1-Ni2 80 ksi CO2 or mix All DCEP Low-alloy, low-temp toughness to -60F (A5.29) E81T1-B2 80 ksi CO2 All DCEP 1.25Cr-0.5Mo for elevated temperature service (A5.29) Gas-shielded vs self-shielded: Gas-shielded FCAW (E71T-1) produces higher quality welds with better mechanical properties and is preferred for code work. Self-shielded FCAW (E71T-8, E71T-11) is essential for outdoor work where wind would blow away external shielding gas. The suffix 'C' means CO2, 'M' means mixed gas (Ar/CO2). Self-shielded wires use DCEN (electrode negative) while gas-shielded typically use DCEP. 5. Stainless Steel Filler Metals (AWS A5.4, A5.9, A5.22) Stainless steel welding is covered by three main specifications: A5.4 (SMAW covered electrodes), A5.9 (bare wire for GMAW/GTAW/SAW), and A5.22 (flux cored and metal cored electrodes). Unlike carbon steel specifications which classify by mechanical properties, stainless steel filler metals are classified primarily by their CHEMICAL COMPOSITION — specifically the chromium, nickel, and molybdenum content, which determines the corrosion resistance and metallurgical behavior of the weld deposit. Classification Spec Tensile Cr % Ni % Mo % Matching Base Metal E308-16 / ER308 A5.4/A5.9 80 ksi 18-21 9-11 0.75 max 304 austenitic stainless E308L-16 / ER308L A5.4/A5.9 75 ksi 18-21 9-11 0.75 max 304L (low carbon, avoids sensitization) E309-16 / ER309 A5.4/A5.9 80 ksi 22-25 12-14 0.75 max Dissimilar joints (CS to SS), cladding E316-16 / ER316L A5.4/A5.9 75 ksi 17-20 11-14 2.0-3.0 316/316L (Mo for pitting resistance) E347-16 / ER347 A5.4/A5.9 75 ksi 18-21 9-11 0.75 max 347/321 (Nb/Ti stabilized grades) E2209-16 / ER2209 A5.4/A5.9 100 ksi 21.5-23.5 8.5-10.5 2.5-3.5 2205 duplex stainless The 'L' suffix matters: 'L' means low carbon (typically 0.04% max vs 0.08% max). Low carbon prevents chromium carbide precipitation (sensitization) during welding, which would reduce corrosion resistance in the heat-affected zone. For virtually all modern stainless welding, the 'L' grade is preferred. E309 for dissimilar joints: When joining carbon steel to stainless steel, E309/ER309 is the standard choice because its higher Cr/Ni content compensates for dilution from the carbon steel side. 6. Nickel & Nickel-Alloy Filler Metals (AWS A5.14, A5.11) Nickel alloy filler metals are essential in oil and gas, chemical processing, power generation, and nuclear industries where extreme corrosion resistance and high-temperature strength are required. AWS A5.14 covers bare electrodes and rods (for GMAW/GTAW/SAW), while A5.11 covers SMAW electrodes. These specifications classify filler metals by their chemical composition. Unlike steel filler metals, nickel alloys have NO mandatory mechanical property requirements in A5.14 — only chemistry is specified. Typical mechanical properties are provided in the informative annex. Classification Common Name Cr % Mo % Ni % Key Application ERNiCr-3 Alloy 82 / Inconel 82 18-22 - 67 min Nuclear, dissimilar welds (SS to CS) ERNiCrMo-3 Alloy 625 / Inconel 625 20-23 8-10 58 min Oil & gas, marine, most versatile Ni filler ERNiCrMo-4 Alloy C-276 / Hastelloy C-276 14.5-16.5 15-17 Bal Severe chemical corrosion (HCl, H2SO4) ERNiCu-7 Monel 400 62-69 Seawater, marine, Cu-Ni systems - - ERNiCrMo-3 (Alloy 625) is the most widely used nickel alloy filler metal in the world. It is used to weld Inconel 625, Inconel 825, various super-austenitic stainless steels (6Mo grades), and 9% nickel steel for LNG cryogenic service. Its combination of chromium (corrosion resistance), molybdenum (pitting resistance), and niobium (strength and solidification cracking resistance) makes it suitable for an extraordinary range of applications. 7. Aluminum Filler Metals (AWS A5.10) Aluminum welding has unique challenges including high thermal conductivity, a tenacious oxide layer, and susceptibility to hot cracking and porosity. AWS A5.10 classifies bare aluminum filler metals by their chemical composition, using the Aluminum Association alloy numbering system (4xxx = Al-Si, 5xxx = Al-Mg). Proper filler metal selection depends on the base metal alloy, whether the joint will be anodized, service temperature, and required strength. Classification Si % Mg % Typical UTS Best For Avoid When ER4043 4.5-6.0 0.05 max ~29 ksi 6061, 6063, castings Max strength needed (use 5356) ER5356 0.25 max 4.5-5.5 ~38 ksi 5052, 5083, 5086 Elevated temp service (>150F continuous) ER5183 0.40 max 4.3-5.2 ~40 ksi 5083, 5456, cryogenic When 5356 is adequate ER4047 11-13 0.10 max ~25 ksi Brazing, highest fluidity Strength-critical applications The 4043 vs 5356 decision is the most common filler metal selection question in aluminum welding. Rule of thumb: Use 4043 for 6xxx-series base metals when you need good fluidity, minimal cracking, and will anodize the finished part (4043 anodizes to a gray color match). Use 5356 for 5xxx-series base metals when you need maximum strength and corrosion resistance, especially in marine service. Never use 5356 on parts that will operate above 150F continuously — the high magnesium content makes it susceptible to stress corrosion cracking at elevated temperatures (known as sensitization in Al-Mg alloys). 8. Complete AWS A5.x Filler Metal Specification Index The table below lists all major AWS A5.x filler metal specifications. Each specification covers a specific combination of base metal type and welding process. When a construction code (like AWS D1.1 or ASME Section IX) references an electrode classification, it points back to the applicable A5.x specification for the full requirements. Spec Title Process Material A5.1 Carbon Steel Electrodes for SMAW SMAW (stick) Carbon steel A5.4 Stainless Steel Electrodes for SMAW SMAW (stick) Stainless steel A5.5 Low-Alloy Steel Electrodes for SMAW SMAW (stick) Low-alloy steel (Cr-Mo, Ni) A5.9 Bare Stainless Steel Electrodes & Rods GMAW/GTAW/SAW Stainless steel A5.10 Bare Aluminum Electrodes & Rods GMAW/GTAW Aluminum alloys A5.11 Nickel Alloy Electrodes for SMAW SMAW (stick) Nickel alloys A5.14 Nickel Alloy Bare Electrodes & Rods GMAW/GTAW/SAW Nickel alloys A5.17 Carbon Steel Electrodes & Fluxes for SAW SAW Carbon steel A5.18 Carbon Steel Electrodes & Rods for GMAW GMAW/GTAW Carbon steel A5.20 Carbon Steel Electrodes for FCAW FCAW Carbon steel A5.22 Stainless Steel FCAW/MCAW Electrodes FCAW Stainless steel A5.28 Low-Alloy Steel Electrodes for GMAW/GTAW GMAW/GTAW Low-alloy steel A5.29 Low-Alloy Steel Electrodes for FCAW FCAW Low-alloy steel A5.36 Carbon/Low-Alloy FCAW/MCAW (unified) FCAW/MCAW Carbon + low-alloy Study Tips for CWI Exam Candidates: The Certified Welding Inspector (CWI) exam frequently tests your ability to decode electrode classifications, match filler metals to base metals, and identify the correct A5.x specification for a given welding scenario. Focus on understanding the classification SYSTEM (what each digit means) rather than memorizing every classification. Know the common electrodes cold: E7018, ER70S-6, E71T-1, E308L, and ER4043. This guide is for educational reference only. It summarizes publicly available AWS classification conventions and general industry knowledge. For official requirements, always consult the current edition of the applicable AWS A5.x specification. Chemical compositions and mechanical properties shown are nominal or minimum values. Version 1.0, March 2026. Not affiliated with the American Welding Society.
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )