Module 6 Lab
Conservation Theories
NAME:
Description
In an effort to prepare you for the term video project in Lab 08, this lab will contain very few
directions. However, you will be expected to supply the major steps you performed in
LoggerPro, to show that you are able to write out the steps performed in a lab experiment. The
idea of conservation laws comes in very handy when dealing with athletes. When a jumper
bends their knees as much as possible, they are building up potential energy. The jumper then
uses this potential energy to reach a maximum kinetic energy and thereby jump further. When
two athletes collide, they will likely undergo an elastic collision and therefore energy and
momentum are conserved. The pain that comes after the collision is likely BECAUSE these two
values were conserved!
Time Spent on Lab = approximately 3 hours, does not need to be done in one sitting
Learning Objectives
●
●
Apply the conservation of momentum to elastic collisions
Apply the conservation of energy to predict the kinematic variables of point masses and
rigid bodies
Materials Needed
●
General props and computer for LoggerPro
Activity #1
1. Using the video you recorded in Lab 02, where you threw a ball across the room, or field
(NOT the video where you threw a ball straight up), estimate the maximum height the
ball traveled above your HAND, not the earth. Write out the major steps you performed
to measure this in LoggerPro. Finally, write down the answer for the height of the ball
above the hand.
Answer:
I estimate the height to be 60 cm. I used the diameter of the ball as a measurement reference.
The calculated height by Logger Pro was 47.4 cm.
2. What is the maximum gravitational potential energy you gave the ball by throwing it into
the air? Write out any equations used with an explanation of why it is appropriate.
Answer:
Module 6 Lab
Conservation Theories
The maximum GPE can be calculated using the equation GPE= mgh Ball weight=50 grams
Therefore: .05*9.81*.474= .232 J
3. Using what you know of the conservation of energy laws, how does this maximum
gravitational potential energy compare to the maximum kinetic energy when the ball left
the hand? Describe the parts of the video where the kinetic energy is maximum.
Answer:
The maximum kinetic energy is going to be when right when the ball leaves my hand as well
as right before it touches the ground. When the Kinetic energy is at its maximum it potential
energy will be low.
4. Calculate an estimate of the maximum velocity the ball/object had and write out your
solution with all mathematical steps involved.
Answer:
Set Max PE= to KE KE=.5mv^2 Therefore Mgh= .5mv^2 The velocity therefore wil bel
.232/(5*.05)=v^2 v=.963 m/s
5. Now measure the velocity of the ball/object, right after it left your hand, using LoggerPro.
Write out all the steps you performed to complete this measurement.
Answer:
To find the velocity I used the balls diameter as a measurement point and then calculated its
vertical velocity to be .87 m/s
6. How do the answers to #4 and #5 compare? Based on the comparison, do you think that
energy was conserved? Justify this response with a percent difference calculation. You
can find examples in the appendices.
Answer:
The values were very clkose to one another however the small difference co0uld be do to an
inaccurate measurement when I was graphing the points.
Activity #2
For this activity, you are welcome to use the Pucks Collide video (link in the Module 6 Lab
instructions in Canvas), or you may link to a video you find interesting on YouTube, so long as
Module 6 Lab
Conservation Theories
you can include the web address to the video for the instructor to see. If you choose your own
video, the video must contain a collision of two objects, with minimally offensive scenes.
7. Will you use the colliding pucks video, or a video you have found online? If an online
video, include the link to the video.
Answer:
Colliding pucks video.
8. Write down the masses of your two objects and how you will scale your distance
measurements, or estimate them to the best of your ability, if you choose an external
video.
Answer:
Each puck 48g. I will scale the distance measuremetns by using the 10 cm mark that is
provided in the video and will use that as a reference in logger pro.
9. Using LoggerPro, measure the x and y components of the velocities of the two objects,
JUST BEFORE THEY COLLIDE. Write your procedures for making these
measurements and clearly denote which velocity belongs to which object, and in which
dimension. That means you could have up to FOUR measurements below, if both of
your objects are moving in two dimensions. You may do this by restarting the software in
between measuring the velocity of each puck, or you may do this by adding a new series
to the software, after analyzing the first puck. This option can be found in the icon below:
Answer:
VelocityX and VelocityY for Blue
Module 6 Lab
Conservation Theories
Velocity X and Velocity Y for Red
Module 6 Lab
Conservation Theories
Module 6 Lab
Conservation Theories
10. Calculate the x and y components of the momentums just before collision, for your two
objects. Write out your calculations below, clearly denoting which momentum belongs to
which object, and in which dimension.
Answer:
For red xmomentum= p=mv .048*.068= .00326 kgm/s
For red ymomentum= .048*.589 = 0.028 kgm/s
For blue xmomentum= .048*.243= .011 kgm/s
For blue ymomentum= .048*.454= .022 kgms
11. Calculate the magnitude of the momentum for each object, just before the collision.
Write out your calculations and place them in the space below.
Answer:
For red squrroot(.00326^2+ .028^2)= 0.02817 kgm/s
For blue squarroot(.11^2 + .022^2)= 0.1122 kgm/s
12. Now repeat steps #9-#11 for the two objects JUST AFTER the collision. Compare your
final momentum magnitudes to those in #11. Write out all your work below.
Answer:
For red xmomentum= p=mv .048*.461= .0218 kgm/s
For red ymomentum= .048*.042 = 0.002 kgm/s
For blue xmomentum= .048*.2= .0096 kgm/s
For blue ymomentum= .048*.481= .0231 kgms
13. Is momentum conserved? Justify your response. Explain any discrepancies between the
magnitudes in terms of decisions you have made during the video analysis.
Answer:
For red squrroot(.0218^2+.002^2)= 0.02189 kgm/s
For blue squarroot(.0096^2+.023^2)= 0.249 kgm/s
Momentum was conserved for red but not for blue, therefore there most have been an error
when I was using logger pro such as an incorrect velocity measurement.
**Upload your finished lab report to the Module 6 Lab: Conservation Theories assignment
area in Canvas.**
Module 6 Lab
Conservation Theories