1A
DTC Table
DTC
C00
DTC name
None
DTC detecting condition
—
IAP sensor circuit high
P0105-H / P0105-L voltage / low voltage
C13
The sensor output voltage is higher than 4.85 V. / The
sensor output voltage is lower than 0.5 V.
IAT sensor circuit high
P0110-H / P0110-L voltage / low voltage
C21
The sensor output voltage is higher than 4.85 V. / The
sensor output voltage is lower than 0.15 V.
ECT sensor circuit high
P0115-H / P0115-L voltage / low voltage
C15
The sensor output voltage is higher than 4.85 V. / The
sensor output voltage is lower than 0.15 V.
TP sensor circuit high voltage
P0120-H / P0120-L / low voltage
The sensor output voltage is higher than 4.8 V. / The
C14 *1
sensor output voltage is lower than 0.2 V.
P0130
C44
P0135
C44
P0201
C32
P0202
C33
P0203
C34
P0204
C35
HO2 sensor circuit
malfunction
HO2 sensor heater circuit
malfunction
Fuel injector #1 circuit
malfunction
Fuel injector #2 circuit
malfunction
Fuel injector #3 circuit
malfunction
Fuel injector #4 circuit
malfunction
Unexpected power supply to
P0230-H / P0230-L fuel pump / Unexpected
power cut to fuel pump
C41
P0335
C12
P0351
C24
P0352
C25
P0353
C26
CKP sensor circuit
malfunction
HO2 sensor output voltage is not input to ECM during
engine operation and running condition.
The heater can not operate so that heater operation voltage
is not supplied to the HO2 sensor heater circuit.
Fuel injector #1 signal is interrupted by 4 times or more
continuity although CKP signal is detected.
Fuel injector #2 signal is interrupted by 4 times or more
continuity although CKP signal is detected.
Fuel injector #3 signal is interrupted by 4 times or more
continuity although CKP signal is detected.
Fuel injector #4 signal is interrupted by 4 times or more
continuity although CKP signal is detected.
Voltage is applied to fuel pump although FP relay is turned
OFF. / No voltage is applied to fuel pump although FP relay
is turned ON.
The signal does not reach ECM for 2 sec. or more, after
receiving the starter signal.
Ignition system #1
malfunction
Ignition coil #1 signal is interrupted by 8 times or more
continuity although CKP signal is detected.
P0351 (C24): Ignition coil #1
Ignition system #2
malfunction
Ignition coil #2 signal is interrupted by 8 times or more
continuity although CKP signal is detected.
P0352 (C25): Ignition coil #2
Ignition system #3
malfunction
Ignition coil #3 signal is interrupted by 8 times or more
continuity although CKP signal is detected.
P0353 (C26): Ignition coil #3
marvelstar-store
P0354
C27
P0443 *2
C62 *2
P0480
C60
P0500
C16
Ignition system #4
malfunction
Ignition coil #4 signal is interrupted by 8 times or more
continuity although CKP signal is detected.
P0354 (C27): Ignition coil #4
EVAP system purge control
solenoid valve circuit
malfunction
EVAP system purge control solenoid valve voltage is not
input to ECM.
Cooling fan relay circuit
malfunction
Cooling fan relay signal is not input to ECM.
Vehicle speed sensor (Front)
circuit malfunction
• Without ABS
The speed sensor signal is not input for more than 3 sec.
• With ABS
P0505
C40
ISC valve circuit malfunction
P0506
C65
ISC valve, lower than desired Idle speed dropped lower than desired idle speed by more
rpm
than specified range.
P0507
C65
ISC valve, higher than
desired rpm
Idle speed rose higher than desired idle speed by more
than specified range.
P0705
C31
GP switch circuit malfunction
Gear position signal voltage is lower than the specified
value.
P1500
C91
Vehicle speed sensor (Rear)
circuit malfunction
• Without ABS
The circuit voltage of motor drive is unusual.
The speed sensor signal is not input for more than 3 sec.
• With ABS
P1650
C42
IG switch circuit malfunction
Ignition switch signal is not input to the ECM.
When the ID agreement is not verified. (With immobilizer
system)
ECM does not receive communication signal from the
immobilizer antenna. (With immobilizer system)
TO sensor circuit high
P1651-H / P1651-L voltage / low voltage
C23
The sensor output voltage is higher than 4.80 V. / The
sensor output voltage is lower than 0.20 V.
STP sensor circuit high
P1654-H / P1654-L voltage / low voltage
C29
The sensor output voltage is higher than 4.85 V. / The
sensor output voltage is lower than 0.15 V.
P1655
C28
P1656
C49
STVA circuit malfunction
PAIR control solenoid valve
circuit malfunction
STVA control signal is not supplied from the ECM.
ECM does not receive communication signal from the STVA
or operation voltage does not reach STVA.
PAIR control solenoid valve voltage is not input to ECM.
EXCVA position sensor circuit
The sensor output voltage is higher than 4.90 V. / The
P1657-H / P1657-L high voltage / low voltage
sensor output voltage is lower than 0.14 V.
C46
P1658
C46
EXCVA motor circuit
malfunction
EXCVA control signal is not supplied from the ECM.
ECM does not receive communication signal from the
EXCVA or operation voltage does not reach EXCVA motor.
AP sensor circuit high voltage
P1750-H / P1750-L / low voltage
The sensor output voltage is higher than 4.85 V. / The
sensor output voltage is lower than 0.5 V.
C17
marvelstar-store