MODIFICATION HISTORY
MODEL NAME : KDL-40/46/52W4000
SERVICE MANUAL
PARTS No. : 9-888-209-02
* Blue characters are linking.
Ver.
DATA
CONTENTS
1.0
2008.06
Issued
1.1
2008.08
Addition of SEC. 2 TROUBLESHOOTING and 3-1. BLOCK DIAGRAM.
(P. 2-1, P. 3-1)
Correction and Addition of parts number for SEC. 4 EXPLODED VIEWS.
(P. 4-2, P. 4-3, P. 4-5, P. 4-6, P. 4-8, P. 4-9)
KDL-40W4000/46W4000/52W4000
SERVICE MANUAL
RM-GD004
KDL-40W4000/46W4000/52W4000
Australia Model
EG1L CHASSIS
LCD Digital Colour TV
SPECIFICATIONS
Model name
KDL-40W4000
System
Panel system
TV system
Colour/video system
Channel coverage
Sound output
Input/Output jacks
Antenna
1
1, 2, 3
1, 2, 3
1/
2
HDMI IN 1, 2, 3
PC IN
(RGB)
i
KDL-46W4000
KDL-52W4000
LCD (Liquid Crystal Display) Panel
Analogue: B/G, I, D/K
Digital: DVB-T
Analogue: PAL, PAL60, SECAM, NTSC3.58/4.43 (only video input)
Digital: MPEG-2 MP@ML/HL
Analogue:
B/G: VHF: E2 to E12 / UHF: E21 to E69 /CATV: S01 to S03, S1 to S41
VHF: 0 to 12, 5A, 9A / UHF: 28 to 69 /CATV: S01 to S03, S1 to S44
I:
UHF: B21 to B69 / CATV: S01 to S03, S1 to S41
D/K: VHF: C1 to C12, R1 to R12 /UHF: C13 to C57, R21 to R60 /
CATV: S01 to S03, S1 to S41, Z1 to Z39
Digital: VHF/UHF
10 W + 10 W
75 ohm external terminal for VHF/UHF
S video input (4-pin mini DIN)
Video input (phono jack)
Audio input (phono jacks): 500 mVrms, Impedance: 47 kilohms
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Y: 1 Vp-p, 75 ohms, 0.3V negative sync/PB/CB: 0.7 Vp-p, 75 ohms/
PR/CR: 0.7 Vp-p, 75 ohms
Video: 1080/24p, 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM
32, 44.1 and 48 kHz, 16, 20 and 24 bits
Analogue audio input (minijack): 500 mVrms, Impedance: 47 kilohms (HDMI IN 3 only)
Video output (phono jack)
DIGITAL AUDIO OUT (OPTICAL) (digital optical jack)/Audio output (phono jacks)
PC Input (D-sub 15-pin)
G: 0.7 Vp-p, 75 ohms, non Sync on Green/B: 0.7 Vp-p, 75 ohms/
R: 0.7 Vp-p, 75 ohms/HD: 1-5 Vp-p/VD: 1-5 Vp-p
PC audio input (minijack)
Headphones jack
USB port
DMPORT
Power and others
Power requirements
Screen size (measured
diagonally)
Display resolution
Power consumption
Dimensions* (with TableTop Stand)
(w × h × d)
(without Table
-Top Stand)
Mass*
DIGITAL MEDIA PORT
220 V – 240 V AC, 50 Hz
40 inches (Approx.
46 inches (Approx.
101.6 cm)
116.8 cm)
1,920 dots (horizontal) × 1,080 lines (vertical)
Indicated on the rear of the TV.
986 × 684 × 279 mm
1,120 × 782 × 307 mm
1,262 × 871 × 347 mm
986 × 646 × 110 mm
1,120 × 742 × 115 mm
1,262 × 829 × 119 mm
29 kg
38 kg
25 kg
32 kg
(with Table22 kg
Top Stand)
(without Table
19 kg
-Top Stand)
Optional accessories
52 inches (Approx.
132.2 cm)
SU-WL500/SU-WL50B Wall-Mount Bracket
SU-FL300M TV stand
SU-WL500/SU-WL50B
Wall-Mount Bracket
*Dimensions and mass are approximate values.
Design and specifications are subject to change without notice.
KDL-40/46/52W4000 (AUS)
2
PC input signal reference chart for PC IN
Resolution
Signals
VGA
SVGA
XGA
WXGA
SXGA
Horizontal
(Pixel)
640
640
720
800
800
1024
1024
1024
1280
1280
1280
1360
1280
× Vertical
(Line)
×
480
×
480
×
400
×
600
×
600
×
768
×
768
×
768
×
768
×
768
×
768
×
768
×
1024
(RGB) jack
Horizontal
frequency (kHz)
31.5
37.5
31.5
37.9
46.9
48.4
56.5
60.0
47.4
47.8
60.3
47.7
64.0
Vertical
frequency (Hz)
60
75
70
60
75
60
70
75
60
60
75
60
60
Standard
VGA
VESA
VGA-T
VESA Guidelines
VESA
VESA Guidelines
VESA
VESA
VESA
VESA
VESA
VESA
• This TV’s PC input does not support Sync on Green or Composite Sync.
• This TV’s PC input does not support interlaced signals.
• This TV’s PC input supports signals in the above chart with a 60 Hz vertical frequency. For other signals, you
will see the message “NO SYNC”.
PC input signal reference chart for HDMI IN 1, 2, 3 jack
Resolution
Signals
VGA
SVGA
XGA
WXGA
SXGA
Horizontal
(Pixel)
640
800
1024
1280
1280
1280
× Vertical
(Line)
×
480
×
600
×
768
×
768
×
768
×
1024
Horizontal
frequency (kHz)
31.5
37.9
48.4
47.4
47.8
64.0
Vertical
frequency (Hz)
60
60
60
60
60
60
rd
Standard
VESA
VESA Guidelines
VESA Guidelines
VESA
VESA
VESA
KDL-40/46/52W4000 (AUS)
3
WARNINGS AND CAUTIONS
SAFETY-RELATED COMPONENT
WARNING
CAUTION
These servicing instructions are for use by qualified service
personnel only.
To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you
are qualified to do so.
It is essential that all critical parts be replaced only with the part
number specified in the electrical parts list to prevent electric
shock, fire, or other hazard.
NOTE: Do not modify the original design without obtaining
written permission from the manufacturer or you will
void the original parts and labor guarantee.
WARNING!!
An isolation transformer should be used during any service to
avoid possible shock hazard, because of live chassis.
The chassis of this receiver is directly connected to the ac power
line.
! SAFETY-RELATED COMPONENT
WARNING!!
Replace all components with Sony parts whose part numbers
appear as shown in this manual or in supplements
published by Sony.
USE CAUTION WHEN HANDLING THE LCD PANEL
When repairing the LCD panel, be sure you are grounded by
using a wrist band.
When repairing the LCD panel on the wall, the LCD panel must
be secured using the 4 mounting holes on the rear cover.
1) Do not press on the panel or frame edge to avoid the risk of
electric shock.
2) Do not scratch or press on the panel with any sharp objects.
3) Do not leave the module in high temperatures or in areas of
high humidity for an extended period of time.
4) Do not expose the LCD panel to direct sunlight.
5) Avoid contact with water. It may cause a short circuit within
the module.
6) Disconnect the AC power when replacing the backlight (CCFL)
or inverter circuit.
(High voltage occurs at the inverter circuit at 650Vrms.)
7) Always clean the LCD panel with a soft cloth material.
8) Use care when handling the wires or connectors of the inverter
circuit. Damaging the wires may cause a short.
9) Protect the panel from ESD to avoid damaging the electronic
circuit (C-MOS).
KDL-40/46/52W4000 (AUS)
4
SAFETY CHECK-OUT
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly
soldered connections. Check the entire board surface for
solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for AC
leakage. Check leakage as described below.
Leakage Test
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part
having a return to chassis, must not exceed 0.5 mA (500
microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’ instructions to
use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision
245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit”
indication is 0.75 V, so analog meters must have an accurate
low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of
passive VOMs that are suitable. Nearly all battery-operated
digital multimeters that have a 2 VAC range are suitable (see
Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground; the cover-plate
retaining screw on most AC outlet boxes is also at earth ground.
If the retaining screw is to be used as your earth ground, verify
that it is at ground by measuring the resistance between it and a
cold-water pipe with an ohmmeter. The reading should be zero
ohms.
If a cold-water pipe is not accessible, connect a 60- to 100-watt
trouble- light (not a neon lamp) between the hot side of the
receptacle and the retaining screw. Try both slots, if necessary,
to locate the hot side on the line; the lamp should light at normal
brilliance if the screw is at ground potential (see Figure B).
To Exposed Metal
Parts on Set
Trouble Light
AC Outlet Box
Ohmmeter
AC
Voltmeter
o
(0.75V)
0.15 µF
Cold-water Pipe
Earth Ground
FigureA. Using an AC voltmeter to check AC leakage.
Figure B. Checking for earth ground.
KDL-40/46/52W4000 (AUS)
5
SELF DIAGNOSIS FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to
reveal past problems and how often these problems occur.
1-1. DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY LED will flash a set number of times to indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a “0”, no error has occurred .
1-2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
[ FLASH COUNT ]
2 times
4 times
5 times
LED ON 0.3 sec.
LED OFF 0.3 sec.
LED OFF
2 sec.
Note: One flash counts is not self-diagnostic.
STANDBY LED
1-3. STOPPING THE STANDBY FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY LED from flashing.
KDL-40/46/52W4000 (AUS)
6
1-4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to
bring up past occurrences of failure for confirmation on the screen:
1-4-1. To Bring Up Screen Test
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
5
( Info/Text reveal ) ( Number button ) * ( Volume )
( TV standby )
* : Note that this differs from entering the service mode (volume +)
[ SELF-DIAGNOSTIC SCREEN DISPLAY ]
1/3
BALANCER
0
POWER
0
PANEL
0
NVM
2
NC
1
HDMI
0
DIGITAL
0
TUNER
0
SOUND
0
Error Count Record
Monitoring Items
2/3
DC_ALERT1
0
DC_ALERT2
0
RTC
0
DC_ALERT2
2
DEMOD
1
USB
0
CI
0
AU_PROT
0
DC_ALERT
0
3/3
VCTP
0
Reset
0
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
After you have completed the repairs, clear the result display to “0”.
1-5. Quitting Self-diagnostic screen
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
KDL-40/46/52W4000 (AUS)
7
TABLE OF CONTENTS
SAFETY CHECK-OUT ............................................. 5
SELF DIAGNOSIS FUNCTION ................................ 6
1. DISASSEMBLY ............................................... 1-1
1-1. KDL-40W4000 ....................................................... 1-1
1-1-1. REAR COVER AND STAND ASSY
REMOVAL ...................................................... 1-1
1-1-2. AC INLET AND UNDER COVER
REMOVAL ...................................................... 1-2
1-1-3. BA1 AND IP5 BOARDS REMOVAL ............ 1-3
1-1-4. FRAME REMOVAL ....................................... 1-4
1-1-5. SPEAKER (L) REMOVAL ............................. 1-5
1-1-6. SPEAKER (R) REMOVAL ............................. 1-5
1-1-7. LCD PANEL, H3E BOARD AND
H4 BOARD REMOVAL ................................. 1-6
1-2. KDL-46W4000 ....................................................... 1-7
1-2-1. REAR COVER AND STAND ASSY
REMOVAL ...................................................... 1-7
1-2-2. AC INLET AND UNDER COVER
REMOVAL ...................................................... 1-8
1-2-3. BA1 AND IP5 BOARDS REMOVAL ............ 1-9
1-2-4. FRAME REMOVAL ..................................... 1-10
1-2-5. SPEAKER (L) REMOVAL ........................... 1-11
1-2-6. SPEAKER (R) REMOVAL ........................... 1-11
1-2-7. LCD PANEL, H3E BOARD AND
H4 BOARD REMOVAL ............................... 1-12
1-3. KDL-52W4000 ..................................................... 1-13
1-3-1. REAR COVER AND STAND ASSY
REMOVAL .................................................... 1-13
1-3-2. AC INLET AND UNDER COVER
REMOVAL .................................................... 1-14
1-3-3. BA1 AND IP5 BOARDS REMOVAL .......... 1-15
1-3-4. FRAME REMOVAL ..................................... 1-16
1-3-5. SPEAKER (L) REMOVAL ........................... 1-17
1-3-6. SPEAKER (R) REMOVAL ........................... 1-17
1-3-7. LCD PANEL, H3E BOARD AND
H4 BOARD REMOVAL ............................... 1-18
2. TROUBLESHOOTING .................................... 2-1
2-1. No Power (Flow Chart_B) ..................................... 2-3
2-2. Self Diagnosis ......................................................... 2-4
2-2-1. Self Diagnosis (Flow Chart_C) ....................... 2-5
2-2-2. POWER_DET (RED 2 times blink) ................ 2-6
2-2-3. Back light Error (RED 6 times blink) ............. 2-6
2-2-4. Temp Error (RED 7 times blink) ..................... 2-7
2-2-5. Audio Error (RED 8 times blink) .................... 2-7
2-2-6. DEF Error (RED 10 times blink) ..................... 2-8
2-2-7. NVM Error (RED 11 times blink) ................... 2-8
2-2-8. I2C Error (RED 12 times blink) ...................... 2-8
2-2-9. Balancer Error (RED 13 times blink) .............. 2-9
2-2-10. HDMI Error (RED 14 times blink) .................. 2-9
2-2-11. Tuner Error (RED 15 times blink) ................... 2-9
2-2-12. I2C-CH1 Error (RED 16 times blink) ........... 2-10
2-2-13. I2C-CH0 Error (RED 17 times blink) ........... 2-10
2-2-14. Digital modulator Error
(RED 18 times blink) ..................................... 2-10
2-2-15. USB Error (RED 19 times blink) .................. 2-11
2-2-16. VCTP Error (RED 21 times blink) ................ 2-11
2-3. Audio Problem (Flow Chart_D) .......................... 2-12
2-4. Video Ploblem (Flow Chart_E) ........................... 2-13
3. DIAGRAMS ..................................................... 3-1
3-1. BLOCK DIAGRAM ..............................................
3-2. CIRCUIT BOARDS LOCATION .........................
(1) KDL-40/46W4000 ...........................................
(2) KDL-52W4000 ................................................
3-1
3-2
3-2
3-2
4. EXPLODED VIEWS ........................................ 4-1
4-1. KDL-40W4000 ....................................................... 4-2
4-1-1. REAR COVER AND STAND ASSY ............. 4-2
4-1-2. CHASSIS-1 ...................................................... 4-3
4-1-3. CHASSIS-2 ...................................................... 4-4
4-2. KDL-46W4000 ....................................................... 4-5
4-2-1. REAR COVER AND STAND ASSY ............. 4-5
4-2-2. CHASSIS-1 ...................................................... 4-6
4-2-3. CHASSIS-2 ...................................................... 4-7
4-3. KDL-52W4000 ....................................................... 4-8
4-3-1. REAR COVER AND STAND ASSY ............. 4-8
4-3-2. CHASSIS-1 ...................................................... 4-9
4-3-3. CHASSIS-2 .................................................... 4-10
4-4. PACKING MATERIALS .................................... 4-11
4-4-1. KDL-40W4000 .............................................. 4-11
4-4-2. KDL-46W4000 .............................................. 4-12
4-4-3. KDL-52W4000 .............................................. 4-13
KDL-40/46/52W4000 (AUS)
8
SECTION 1
DISASSEMBLY
1-1. KDL-40W4000
1-1-1. REAR COVER AND STAND ASSY REMOVAL
3 Six screws
(+BVTP2 4X16)
4 Two screws
(+PSW M5X12)
6 Three screws
(+BV 3X12)
4 Two screws
(+PSW M5X12)
3 Five screws
(+BVTP2 4X16)
3 Four screws
(+BVTP2 4X16)
3 Two screws 5Two screws
(+BVTP2 4X16) (+PSW M5X12)
3 Two screws
(+BVTP2 4X16)
1 Four screws
(+PSW M5X20)
2 Stand assy
7 Rear cover
8 Switch unit
KDL-40/46/52W4000 (AUS)
1-1
KDL-40W4000
1-1-2. AC INLET AND UNDER COVER REMOVAL
2 Under bar (L)
1 Two screws
(+BVTP2 4X16)
7 One screw
(+BVST 3X8)
8 AC inlet bracket
5 Two screws
(+KTT 3X10)
3 One screw
(+BVST 3X8)
6 AC inlet
4 Under cover
KDL-40/46/52W4000 (AUS)
1-2
KDL-40W4000
1-1-3. BA1 AND IP5 BOARDS REMOVAL
3 Two screws
(+PSW M3X5)
5 Three screws
(+BVST 3X8)
4 Two screws
(SP 4-4O UNC)
0 One screw
(+BVST 3X8)
9 Side jack
bracket assy
7 One screw
(+BVST 3X8)
qs Two screws
(+BVST 3X8)
6 B shield assy
0 One screw
(+BVST 3X8)
0 Four screws
(+BVST 3X8)
qa BA1 board
1 Three screws
(+BVST 3X8)
2 IP5 board
1 Three screws
(+BVST 3X8)
qs Two screws
(+BVST 3X8)
qd Main bracket
assy
8 Lead wire with
connector(LVDS)
KDL-40/46/52W4000 (AUS)
1-3
KDL-40W4000
1-1-4. FRAME REMOVAL
3 Two screws (+PSW M5X8)
4 Vesa frame (BTM) assy
9 Two screws (+PSW M5X8)
1 Two screws
(+PSW M5X8)
2 Vesa frame (TOP)
5 Three screws
(+PSW M4X8)
7 Two screws
(+PSW M5X8)
8 Vesa frame
(TOP)
0 Vesa frame (BTM)
assy
qa Three screws
(+PSW M4X8)
qs Spine frame assy
6 Spine frame assy
qd Four screws
(+BVTP2 4X16)
qf Bottom frame
assy
KDL-40/46/52W4000 (AUS)
1-4
KDL-40W4000
1-1-5. SPEAKER (L) REMOVAL
1 Loudspeaker
Both
Both
1-1-6. SPEAKER (R) REMOVAL
1 Loudspeaker
Both
Both
KDL-40/46/52W4000 (AUS)
1-5
KDL-40W4000
1-1-7. LCD PANEL, H3E BOARD AND H4 BOARD REMOVAL
8 LCD panel
7 Two screws
(+BVTP2 4X16)
1 H3E board
6 Illumination module
2 H4 board
3 One screw
(+BV 3X12)
Both
4 Light guide
5 Clear panel
Both
9 Bezel assy
KDL-40/46/52W4000 (AUS)
1-6
1-2. KDL-46W4000
1-2-1. REAR COVER AND STAND ASSY REMOVAL
3 Six screws
(+BVTP2 4X16)
4 Four screws
(+PSW M5X12)
3 Five screws
(+BVTP2 4X16)
3 Ten screws
(+BVTP2 4X16)
4 Two screws
(+PSW M5X12)
5 Three screws
(+BV 3X12)
2 Stand assy (L)
1 Four screws
(+PSW M5X20)
6 Rear cover
7 Switch unit
KDL-40/46/52W4000 (AUS)
1-7
KDL-46W4000
1-2-2. AC INLET AND UNDER COVER REMOVAL
2 Under bar (L)
7 One Screw
(+BVST 3X8)
8 AC inlet bracket
6 AC inlet
4 Under cover (L2)
1 Two screws
(+BVTP2 4X16)
5 Two screws
(+KTT 3X10)
3 One screws
(+BVST 3X8)
KDL-40/46/52W4000 (AUS)
1-8
KDL-46W4000
1-2-3. BA1 AND IP5 BOARDS REMOVAL
5 Three screws
(+BVST 3X8)
9 One screw
(+BVTP2 4X16)
4 Two screws
(SP 4-4O UNC)
qa One screw
(+BVST 3X8)
0 Side jack
bracket assy
3 Two screws
(+PSW M3X8)
6 B shield assy
qa One screw
(+BVST 3X8)
qa Four screws
(+BVST 3X8)
qs BA1 board
1 Three screws
qd Two screws (+BVST 3X8) 2 IP5 board
1 Three screws
(+BVST 3X8)
(+BVST 3X8)
7 One screw
(+BVST 3X8)
qf Main bracket assy
qh Vesa frame
(TOP)
qg Two screws
(+PSW M5X8)
8 Lead wire with
connector (LVDS)
KDL-40/46/52W4000 (AUS)
1-9
KDL-46W4000
1-2-4. FRAME REMOVAL
5 Two screws
(+PSW M5X8)
1 One screw
(+PSW M5X8)
3 Two screws
(+BVST 3X8)
6 Vesa frame
(BTM) assy
0 Two scxrews
(+PSW M5X8)
qa Vesa frame
(BTM) assy
2 Center frame
7 Five screws
(+PSW M5X8)
8 One screw
(+BVTP2 4X16)
4 G5 frame
1 One screw
(+PSW M5X8)
qg One screw
(+PSW M5X8)
qs Five screws
(+PSW M5X8)
qf Spine frame assy
9 Spine frame
assy
qd One screw
(+BVTP2 4X16)
qh Four screws
(+BVTP2 4X16)
qj Bottom frame
assy
KDL-40/46/52W4000 (AUS)
1-10
KDL-46W4000
1-2-5. SPEAKER (L) REMOVAL
1 Loudspeaker
2 Speaker cushion
Both
Both
1-2-6. SPEAKER (R) REMOVAL
1 Loudspeaker
Both
2 Speaker cushion
Both
KDL-40/46/52W4000 (AUS)
1-11
KDL-46W4000
1-2-7. LCD PANEL, H3E BOARD AND H4 BOARD REMOVAL
8 LCD panel
7 Two screws
(+BVTP2 4X16)
1 H3E board
2 H4 board
6 Illumination module
3 One screw
(+BV 3X12)
4 Light guide
Both
5 Clear panel
Both
9 Bezel assy
KDL-40/46/52W4000 (AUS)
1-12
1-3. KDL-52W4000
1-3-1. REAR COVER AND STAND ASSY REMOVAL
3 Six screws
(+BVTP2 4X16)
4 Four screws
(+PSW M5X12)
5 Two screws
(+BV 3X12)
3 Nine screws
(+BVTP2 4X16)
3 Six screws
(+BVTP2 4X16)
4 Two screws
(+PSW M5X12)
1 Four screws
(+PSW M5X16)
2 Stand assy (LL)
6 Rear cover
7 Switch unit
KDL-40/46/52W4000 (AUS)
1-13
KDL-52W4000
1-3-2. AC INLET AND UNDER COVER REMOVAL
5 Two screws
(+KTT 3X10
(S TYPE))
7 One screw
(+BVST 3X8)
2 Under bar (L)
1 Two screws
(+BVTP2 4X16)
8 AC inlet
bracket
6 AC inlet
3 One screw
(+BVST 3X8)
4 Under cover (LL)
KDL-40/46/52W4000 (AUS)
1-14
KDL-52W4000
1-3-3. BA1 AND IP5 BOARDS REMOVAL
ql Three screws
(+BVST 3X8)
w; G5 board
ql Three screws
(+BVST 3X8)
qa Four screws
(+PSW M3X5)
qd Three screws
(+BVST 3X8)
qs Two screws
(SP 4-4O UNC)
qg One screw
(+BVST 3X8)
8 Side jack bracket assy
qf B shield assy
qg One screw
(+BVST 3X8)
qg Four screws
(+BVST 3X8)
qh BA1 board
9 One screw
(+BVST 3X8)
qj Four screws
(+BVST 3X8)
ws D4 board
qk Main bracket
assy
wa Four screws
(+BVST 3X8)
3 Four screws
(+BVST 3X8)
1 Two screws
(+PSW M5X8)
4 D5 board
5 One screw
(+BVST 3X8)
6 One screw
(+PSW M3X8)
7 D5 frame
2 Vesa frame
(TOP)
0 Lead wire with
connector (LVDS)
KDL-40/46/52W4000 (AUS)
1-15
KDL-52W4000
1-3-4. FRAME REMOVAL
5 Two screws
(+PSW M5X8)
1 One screw
(+PSW M5X8)
6 Vesa frame(BTM)
assy
3 Two screws
(+BVST 3X8)
0 Two screws
(+PSW M5X8)
qa Vesa frame (BTM)
assy
2 Center frame
7 Five screws
(+PSW M5X8)
8 One screw
(+BVTP2 4X16)
9 Spine frame
assy
4 G5 frame
1 One screw
(+PSW M5X8)
qd One screw
(+BVTP2 4X16)
qs Five screws
(+PSW M5X8)
qf Spine frame
ASSY
qg Four screws
(+BVTP2 4X16)
qh Bottom frame
assy
KDL-40/46/52W4000 (AUS)
1-16
KDL-52W4000
1-3-5. SPEAKER (L) REMOVAL
1 Loudspeaker
2 Speaker cushion
Both
Both
1-3-6. SPEAKER (R) REMOVAL
1 Loudspeaker
Both
2 Speaker cushion
Both
KDL-40/46/52W4000 (AUS)
1-17
KDL-52W4000
1-3-7. LCD PANEL, H3E BOARD AND H4 BOARD REMOVAL
8 LCD pane
7 Two screws
(+BVTP2 4X16)
1 H3E board
5 Clear panel
2 H4 board
6 Illumination module
3 One screw
(+BV 3X12)
4 Light guide
Both
Both
9 Bezel assy
KDL-40/46/52W4000 (AUS)
1-18E
SECTION 2
TROUBLESHOOTING
Reference
Symptoms - (dead set)
2
Blinks
6
Blinks
7
Blinks
8
Blinks
10
Blinks
11
Blinks
C
C
C
12
Blinks
13
Blinks
14
Blinks
15
Blinks
C
C
C
C
C
C
NVM
I2C
VCT
Tuner
I2C
CH1
16
Blinks
17
Blinks
18
Blinks
19
Blinks
21
Blinks
No Power
C
C
C
C
B
I2C
CH0
D
Demod
USB
VCTP
BA1 COMPL
D5 COMPL (52")
D4 COMPL (52")
G5 COMPL (52")
IP5 COMPL (46")
IP5 COMPL (40")
Panel Module
Flowchart Reference
C
C
Problem
Power_
DET
Back
Light
Reference
Video - distorted or missing
No Video
BL OK
OSD OK
No
Video
No BL
E
E
TEMP
Audio
DFE
No Video
No
BL OK
Tuner
No OSD Video OK
No
HDMI
No
Audio
E
D
Balancer HDMI
BA1 COMPL
D5 COMPL(52")
D4 COMPL(52")
G5 COMPL(52")
IP5 COMPL(46")
IP5 COMPL(40")
Panel Module
Flowchart Reference
E
E
Problem
: Doubtful part
: just a few possibility
KDL-40/46/52W4000 (AUS)
2-1
Troubleshooting
Set Power
NO
See
2-1. No Power (Chart_B)
Red blinks
See
2-2. Self Diagnosis
(Chart_C)
YES
LED
Green
Audio
See
2-3. Audio Problem (Chart_D)
Video
See
2-4. Video problem (Chart_E)
KDL-40/46/52W4000 (AUS)
2-2
2-1. No Power (Flow Chart_B)
No Power
(No relay clicks)
207-253VAC
Inlet on Power Board 1)
No
AC cable or AC inlet
Yes
3.3VDC
(CN6401 3Pin on
BA1 board)
NO
Power Board 1)
(No STBY3.3V)
YES
Does Power
button work?
NO
Switch Unit
YES
BA1 board
1) 40", 46" : IP5 BOARD
52"
: G5 BOARD
KDL-40/46/52W4000 (AUS)
2-3
2-2. Self Diagnosis
Red LED
Blink
2 times
Display
(Self Diagnosis mode)
Power_DET (12V Main Voltage)
Main Supply Voltage Trouble.
6 times
Panel Det Error
Backlight Trouble.
7 times
Internal Temperature Error
Monitor an Increase of an Inside-Temperature.
8 times
Audio Error (SP Protection)
Audio Trouble.
9 times
HFR Error
HFR Error (for EMH and Cumin).
10 times
Digital Error
DEF (Digital Front End Module) Trouble.
11 times
NVM Error
EEPROM Error (notread/write available).
12 times
I2C Error VCT
VCT I2C Bus Trouble.
13 times
Balance Error
Panel Balance Trouble.
14 times
HDMI Error
HDCP cannot be setup correctly.
15 times
Tuner Error
If circuit or PLL circuit do not respond to IIC commands.
16 times
I2C CH1 (VERD TAS)
I2C Ch1 Error in VERD.
17 times
I2C CH0 (VERD NVM/RTC)
I2C Ch0 Error in VERD.
18 times
Digital Demod
No Acknowledge detected.
19 times
USB Error
USB over current detected.
20 times
CI Error
CI Trouble.
21 times
VCT Error
No DPI-I2C
22 times
MSP Error
MSP3410G IC does not respond to IIC commands.
Contents
When self diagnosis happens, STBY (Red) LED blinks and the history can be
seen on display by self diagnosis mode.
KDL-40/46/52W4000 (AUS)
2-4
2-2-1. Self Diagnosis (Flow Chart_C)
RED LED Blinks
YES
2 times
See
2-2-2. POWER_DET
YES
6 times
See
2-2-3. Back light Error
NO
YES
See
2-2-10. HDMI Error
YES
See
2-2-11. Tuner Error
YES
See
2-2-12. I2C-CH1 Error
YES
See
2-2-13. I2C-CH0 Error
YES
See
2-2-14. Digital modulator Error
YES
See
2-2-15. USB Error
YES
See
2-2-16. VCTP Error
14 times
NO
YES
See
2-2-4. Temp Error
15 times
NO
NO
8 times
See
2-2-9. Balancer Error
NO
NO
7 times
YES
13 times
YES
See
2-2-5 Audio Error
16 times
See
2-2-6. DEF Error
17 times
NO
YES
10 times
NO
NO
YES
11 times
See
2-2-7. NVM Error
NO
12 times
NO
18 times
NO
YES
See
2-2-8. I2C Error
19 times
NO
21 times
KDL-40/46/52W4000 (AUS)
2-5
2-2-2. POWER_DET (RED 2 times blink)
• This indicates DC_DET of Power Board 1).
• 12V line on Power Board 1).
• VERD micro (on BA1 board) Pin6 detects POWER_DET and shuts down chassis power to standby
status.
VERD micro Pin6
Normal condition: 1.3V - 2.5V
Error case: lower than 1.3V or higher than 2.5V
– Replace Power Board 1).
1) 40", 46" : IP5 BOARD
52"
: G5 BOARD
2-2-3. Back light Error (RED 6 times blink)
• This indicates panel power circuit error such as inverter.
• VERD micro (on BA! board) Pin40 detects PANEL_DET and shuts down chassis power to
standby status.
VERD micro Pin40 Normal condition: High / Error case: Low (lower than 0.8V)
– Replace Panel or Power1)/Inverter Board .
1) 40", 46" : IP5 BOARD
52"
: G5 BOARD
KDL-40/46/52W4000 (AUS)
2-6
2-2-4. Temp Error (RED 7 times blink)
• This indicates high temperature inside chassis.
IC5507 on BA1 board is monitoring temperature.
IC5507 is controlled by VERD micro.
• When it happens:
– Check chassis environment.
– Check around IC5507 and replace BA1 board if temperature monitoring circuit
has problem.
– Check panel.
2-2-5. Audio Error (RED 8 times blink)
• This indicates Audio Error (Protection).
• It happens:
– IC8200 on BA1 board, Audio Amp detects over current, thermal shut down
and/or low voltage of itself.
– DC voltage detected for audio line.
– VERD micro Pin5
Normal condition: High / Error case: Low
• Check UNREG15V at CN6401 Pin4 and Pin5 on BA1 board .
And F3401 on BA1 board has 13V or not.
• Check above and replace BA1 board.
KDL-40/46/52W4000 (AUS)
2-7
2-2-6. DEF Error (RED 10 times blink)
• This indicates DEF communication error.
• [ communication error ]
– TVM micro (on BA1 board) is communicating with EMMA3SL (on BA1 board).
• Check above and replace BA1 board .
2-2-7. NVM Error (RED 11 times blink)
• This indicates VERD NVM communication error.
• VERD micro (on BA1 board) is communicating with NVM (on BA1 board) .
• Check above and replace BA1 board.
2-2-8. I2C Error (RED 12 times blink)
• This indicates I2C communication error.
• VCTP micro (on BA1 board) is communicating with each devices (on BA1 board).
• Check above and replace BA1 board .
KDL-40/46/52W4000 (AUS)
2-8
2-2-9. Balancer Error (RED 13 times blink)
• This indicates panel power circuit error such as inverter.
• VERD micro (on BA1 board) Pin81 detects PANEL_DET and shuts down chassis power
to Standby status.
VERD micro Pin40
Normal condition: High / Error case: Mid (0.85 - 2.65V)
• Replace Panel or Power1)/Inverter board.
1) 40", 46" : IP5 BOARD
52"
: G5 BOARD
2-2-10. HDMI Error (RED 14 times blink)
• This indicates HDCP error.
• HDMI setting trouble matter on BA1 board.
• Check above and replace BA1 board.
2-2-11. Tuner Error (RED 15 times blink)
• This indicates Tuner error.
• VCTP and EMMA3SL micro (on BA1 board) is communicating with Tuner
(TU2200) on BA1 board.
• Check above and replace BA1 board.
KDL-40/46/52W4000 (AUS)
2-9
2-2-12. I2C-CH1 Error (RED 16 times blink)
• This indicates I2C communication error.
• VERD micro (on BA1 board) is communicating with Audio processor
(IC3201) on BA1 board.
• Check above and replace BA1 board.
2-2-13. I2C-CH0 Error (RED 17 times blink)
• This indicates I2C communication error.
• VERD micro (on BA1 board) is communicating with Real time clock
(IC5502) on BA1 board.
• Check above and replace BA1 board.
2-2-14. Digital modulator Error (RED 18 times blink)
• This indicates Tuner error.
• EMMA3SL micro is communicating with inside of the Tuner
(TU2200) on BA1 board.
• Check above and replace BA1 board.
KDL-40/46/52W4000 (AUS)
2-10
2-2-15. USB Error (RED 19 times blink)
• This indicates USB error.
• EMMA3SL micro found out USB over current detection on BA1 board.
• Check above and replace BA1 board.
2-2-16. VCTP Error (RED 21 times blink)
• This indicates VCTP error.
• VCTP micro (IC4701) does not work normaly.
• Check above and replace BA1 board.
KDL-40/46/52W4000 (AUS)
2-11
2-3. Audio Problem (Flow Chart_D)
Here is trouble shooting flow related audio.
Audio problem
Only
Speaker out?
NO
HDMI
Problem?
YES
YES
Check
BA1 board
UI setting
correct?
Volume, SP off/On
HP Link
NO
Analog
Channel
Problem?
YES
Check
BA1 board
NO
Digital
Channel
Problem?
NO
Check
BA1 board
YES
Check
BA1 board
YES
NO
Set correctly or
reset by menu.
Check
Speaker or BA1 board
KDL-40/46/52W4000 (AUS)
2-12
2-4. Video Ploblem (Flow Chart_E)
Here is trouble shooting flow related Video.
Video problem
All inputs
have
problem?
NO
HDMI
Problem?
NO
YES
YES
YES
Check
BA1 board
Back Light
turn on?
NO
Check
LVDS harness
Power Board 1)
BA1 board
Panel Module
YES
OSD
appear?
Analog
Channel
Problem?
Check
BA1 board
NO
Digital
Channel
Problem?
NO
Check
BA1 board
YES
Check
BA1 board
YES
NO
Check
LVDS harness
BA1 board
Panel Module
Check
BA1 board
1) 40", 46" : IP5 BOARD
52"
: G5 BOARD
KDL-40/46/52W4000 (AUS)
2-13E
SECTION 3
DIAGRAMS
3-1. BLOCK DIAGRAM
BA1 BOARD
Audio
for PC
PC
HDMI 1 HDMI 2 L
HDMI 3
Audio
for DVI
DDR2 667
512Mb
DDR2 667
512Mb
Hs/Vs
EQ
NAND Flash
256Mb
Main Micro
VCT Premium
EMMA
EMMA3SL
MS
MPEG/AVC decoder
USB 2.0
MPEG2/AVC-HD,USB,XMB
SW
TS [0:7]
RF
UFE4
New Decoder IC
small package
Analog RF CVBS
SIF
Temp Sensor
SCART->RCA Pin
A/V switch
Color Decoder
3D Comb
PC/HD ADC
Audio Dig Decoder
Audio Delay
Scaler
Noise Reduction
Histogram
TV control
TXT Decoding
HDMI Decoder
WCG
S-Force
Graphics RGB[0:7] x3 around 30MHz
Graphics CLK/Hs/Vs
Graphics CLK/Hs/Vs
Digital[0:15] 74MHz
Digital RF CVBS
Analog RF CVBS
SIF
RTC
STBY Micro
LVDS
DDR2 667
256Mb
Backlight
Inverter
DDR2 667
256Mb
Panel
FHD capable. HDMI receiver
and WCG block integrated,
xvYCC capable
Less ST-BY power consumption, control of TAS
(S)Video1
TAS
S-Force
Video2 L
Audio Amp.
TPA3100D2
Video3
Line Out
Component1
BASI
(New Audio IC)
Component2
New Audio IC input SW,
buffer, HP amp
Mon/Rec
Out
SP
Mon/Rec Out
HP Out
DM Port
HP
SW
Optical
Audio Out
CVBS
Y/C
Analog-Component/RGB
Digital-Component
PC-RGB
Audio (Analog)
Audio (Digital)
Audio out
(Var/Fix)
KDL-40/46/52W4000 (AUS)
3-1
3-2. CIRCUIT BOARDS LOCATION
(1)
KDL-40/46W4000
Switch Unit
IP5 board
BA1 board
Inverter board
Illumination module
H4 board
H3E board
(2)
KDL-52W4000
D5 board
Switch Unit
Inverter board
G5 board
D4 board
BA1 board
Inverter board
Illumination module
H4 board
H3E board
KDL-40/46/52W4000 (AUS)
3-2E
SECTION 4
EXPLODED VIEWS
NOTE:
• Items with no part number and no description are
not stocked because they are seldom required for
roution service.
• The construction parts of an assembled part are
indicated with a collation number in the remark
colum.
• Items marked " * " are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
KDL-40/46/52W4000 (AUS)
4-1
4-1. KDL-40W4000
4-1-1. REAR COVER AND STAND ASSY
1
1
12
#1
1
1
1
1
1
2
1
5
4
5
3
6
REF. No.
1
2
3
4
5
PART No.
2-580-640-01
2-580-607-01
3-452-815-01
! 3-289-962-21
* 3-106-086-01
DESCRIPTION
SCREW, +BVTP2 4X16
SCREW, +PSW M5X12
SCREW, +PSW M5X20
COVER, REAR (40)
COVER, ECS
MARK
REF. No.
PART No.
DESCRIPTION
6
X-2189-410-1
STAND (ML) ASSY
#1
7-685-648-79
SCREW +BVTP 3X12 TYPE2 IT-3
KDL-40/46/52W4000 (AUS)
MARK
4-2
KDL-40W4000
4-1-2. CHASSIS-1
51
52
53
53
55
53
53
57
53
53
53
53
53
54
56
59
61
53
60
58
REF. No.
51
52
53
54
55
PART No.
1-480-710-11
1-835-699-11
DESCRIPTION
SWITCH UNIT
LEAD WIRE WITH CONNECTOR
(LVDS)
2-580-629-01 SCREW, +BVST 3X8
2-580-626-01 SCREW, SP 4-4O UNC
A-1547-342-A BA1 MOUNT
MARK
53
REF. No.
PART No.
56
57
58
59
60
2-596-649-01
! 1-822-097-11
2-580-640-01
2-580-592-01
! A-1549-337-C
61
* 1-835-147-11
DESCRIPTION
MARK
+KTT 3X10 (S TYPE)
AC INLET
SCREW, +BVTP2 4X16
SCREW, +PSW M3X8
IP5 MOUNT
CONNECTOR ASSY, MDF61
KDL-40/46/52W4000 (AUS)
4-3
KDL-40W4000
4-1-3. CHASSIS-2
101
102
103
105
104
109
107
#1
108
111
110
106
112
112
105
REF. No.
PART No.
101
X-2318-222-1
102
1-826-888-11
103 ! 1-802-664-11
104
1-480-680-11
105
2-580-600-01
DESCRIPTION
BEZEL ASSY (EM40)
LOUDSPEAKER
LCD PANEL (40INCH FHD TFT)
ILLUMINATION MODULE
SCREW, +PSW M4X8
MARK
REF. No.
PART No.
DESCRIPTION
106
107
108
109
110
2-580-606-01
1-826-888-21
A-1510-351-A
* 3-290-361-01
A-1510-350-A
SCREW, +PSW M5X8
LOUDSPEAKER
H4 MOUNT
GUIDE, LIGHT
H3E MOUNT
111
112
* 3-289-965-01
2-580-640-01
PANEL, CLEAR (40)
SCREW, +BVTP2 4X16
#1
7-685-648-79
106
MARK
SCREW +BVTP 3X12 TYPE2 IT-3
KDL-40/46/52W4000 (AUS)
4-4
4-2. KDL-46W4000
4-2-1. REAR COVER AND STAND ASSY
152
151
152
152
#1
151
155
156
156
153
154
REF. No.
151
152
153
154
155 !
PART No.
DESCRIPTION
2-580-607-01
2-580-640-01
3-452-815-01
X-2189-411-1
3-293-587-21
SCREW, +PSW M5X12
SCREW, +BVTP2 4X16
SCREW, +PSW M5X20
STAND (L) ASSY
COVER, REAR (46)
MARK
REF. No.
PART No.
DESCRIPTION
156
3-106-086-01
COVER, ECS
#1
7-685-648-79
SCREW +BVTP 3X12 TYPE2 IT-3
KDL-40/46/52W4000 (AUS)
MARK
4-5
KDL-46W4000
4-2-2. CHASSIS-1
201
208
204
202
206
203
206
202
206
202
211
206
206
209
206
206
208
210
208
202
207
205
206
202
206
202
206
212
202
208
REF. No.
PART No.
DESCRIPTION
201
202
203
204
1-480-710-11
2-580-606-01
A-1547-580-A
1-835-700-11
205
2-596-649-01
SWITCH UNIT
SCREW, +PSW M5X8
BA1 MOUNT
LEAD WIRE WITH CONNECTOR
(LVDS)
+KTT 3X10 (S TYPE)
206
2-580-629-01
207 ! A-1549-338-C
208
2-580-640-01
209
2-580-592-01
210 ! 1-822-097-11
MARK
REF. No.
211
212
PART No.
2-580-626-01
* 1-835-148-11
206
DESCRIPTION
MARK
SCREW, SP 4-4O UNC
CONNECTOR ASSY, MDF61
SCREW, +BVST 3X8
IP5 MOUNT
SCREW, +BVTP2 4X16
SCREW, +PSW M3X8
AC INLET
KDL-40/46/52W4000 (AUS)
4-6
KDL-46W4000
4-2-3. CHASSIS-2
251
255
253
252
259
258
#1
257
256
254
260
REF. No.
251
252
253
254
255 !
PART No.
DESCRIPTION
MARK
X-2318-223-1
1-480-680-11
1-826-887-11
1-826-887-21
1-802-663-12
BEZEL ASSY (EM46)
ILLUMINATION MODULE
LOUDSPEAKER (3CM, 6.5X15CM)
LOUDSPEAKER (3CM, 6.5X15CM)
LCD PANEL (46INCH FHD TFT)
REF. No.
PART No.
256
257
258
259
260
A-1510-350-A
A-1510-351-A
* 3-290-361-01
* 3-293-434-01
2-580-640-01
#1
7-685-648-79
DESCRIPTION
MARK
H3E MOUNT
H4 MOUNT
GUIDE, LIGHT
PANEL, CLEAR (46)
SCREW, +BVTP2 4X16
SCREW +BVTP 3X12 TYPE2 IT-3
KDL-40/46/52W4000 (AUS)
4-7
4-3. KDL-52W4000
4-3-1. REAR COVER AND STAND ASSY
301
302
#1
301
301
302
306
305
305
303
304
REF. No.
301
302
303
304
305
PART No.
2-580-640-01
2-580-607-01
2-580-608-01
X-2190-786-4
* 3-106-086-01
DESCRIPTION
SCREW, +BVTP2 4X16
SCREW, +PSW M5X12
SCREW, +PSW M5X16
STAND ASSY (LL)
COVER, ECS
MARK
REF. No.
PART No.
DESCRIPTION
306 ! 3-293-625-11
COVER, REAR (52)
#1
SCREW +BVTP 3X12 TYPE2 IT-3
7-685-648-79
KDL-40/46/52W4000 (AUS)
MARK
4-8
KDL-52W4000
4-3-2. CHASSIS-1
351
352
365
353
353
354
353
353
353
353
362
353
355
361
356
353
353
357
353
358
353
353
363
364
360
359
REF. No.
351
352
PART No.
DESCRIPTION
1-480-710-11
1-835-701-11
SWITCH UNIT
LEAD WIRE WITH CONNECTOR
(LVDS)
353
2-580-629-01 SCREW, +BVST 3X8
354 ! A-1511-383-B D5 COMPL
355
A-1547-585-A BA1 COMPL
356
2-580-626-01
357
2-580-591-01
358 ! A-1545-447-C
359 ! 3-284-269-02
360
2-580-606-01
MARK
REF. No.
PART No.
DESCRIPTION
MARK
361
2-596-649-01 +KTT 3X10 (S TYPE)
362 ! 1-821-909-11 AC INLET
363 ! A-1511-382-B D4 COMPL
364
2-580-640-01 SCREW, +BVTP2 4X16
365
2-580-592-01 SCREW, +PSW M3X8
SCREW, SP 4-4O UNC
SCREW, +PSW M3X5
G5-A COMPL
COVER, UNDER (LL)
SCREW, +PSW M5X8
KDL-40/46/52W4000 (AUS)
4-9
KDL-52W4000
4-3-3. CHASSIS-2
401
403
404
405
402
406
409
408
#1
405
410
411
405
406
412
405
406
406
406
407
406
REF. No.
PART No.
401
X-2318-224-1
402
1-480-680-11
403
1-826-887-11
404 ! 1-802-662-11
405
2-580-640-01
DESCRIPTION
MARK
BEZEL ASSY (EM52)
ILLUMINATION MODULE
LOUDSPEAKER (3CM, 6.5X15CM)
LCD PANEL (52INCH FHD TFT)
SCREW, +BVTP2 4X16
REF. No.
PART No.
DESCRIPTION
MARK
406
407
408
409
410
2-580-606-01
2-580-629-01
* 3-293-431-11
* 3-290-361-01
* A-1510-351-A
411
412
* A-1510-350-A H3E MOUNT
1-826-887-21 LOUDSPEAKER (3CM, 6.5X15CM)
#1
7-685-648-79
SCREW, +PSW M5X8
SCREW, +BVST 3X8
PANEL, CLEAR (52)
GUIDE, LIGHT
H4 MOUNT
SCREW +BVTP 3X12 TYPE2 IT-3
KDL-40/46/52W4000 (AUS)
4-10
4-4. PACKING MATERIALS
4-4-1. KDL-40W4000
456 457
455
453
452
454
451
REF. No.
PART No.
451 * 3-295-296-01
452 * 4-106-880-01
453 * 3-295-295-01
454 ! 1-835-167-11
455
1-480-777-11
DESCRIPTION
MARK
CUSHION (LOWER)
INDIVIDUAL CARTON
CUSHION (UPPER)
POWER-SUPPLY CORD
REMOTE COMMANDER (RM-GD004)
REF. No.
PART No.
456 ! 3-876-436-11
457
3-876-827-11
DESCRIPTION
MARK
MANUAL, INSTRUCTION
MANUAL, INSTRUCTION
(WALL MOUNT)
KDL-40/46/52W4000 (AUS)
4-11
4-4-2. KDL-46W4000
506
507
504
505
503
501 502
508
REF. No.
PART No.
501 ! 3-876-436-11
502
3-876-827-11
503 * 3-295-300-01
504
1-480-777-11
505 ! 1-835-167-11
DESCRIPTION
MARK
MANUAL, INSTRUCTION
MANUAL, INSTRUCTION
(WALL MOUNT)
CUSHION (LOWER)
REMOTE COMMANDER (RM-GD004)
POWER-SUPPLY CORD
REF. No.
506
507
508
PART No.
* 3-295-299-01
* 4-106-881-01
* 2-639-807-01
DESCRIPTION
MARK
CUSHION (UPPER)
INDIVIDUAL CARTON
JOINT
KDL-40/46/52W4000 (AUS)
4-12
4-4-3. KDL-52W4000
556
557
555
554
553
551 552
558
REF. No.
PART No.
551 ! 3-876-436-11
552
3-876-827-11
553 * 3-295-392-01
554
1-480-777-11
555 ! 1-835-167-11
DESCRIPTION
MARK
MANUAL,INSTRUCTION
MANUAL,INSTRUCTION
(WALL MOUNT)
CUSHION LOWER
REMOTE COMMANDER (RM-GD004)
POWER-SUPPLY CORD
REF. No.
556
557
558
PART No.
* 3-295-391-01
* 4-106-882-01
* 2-639-807-01
DESCRIPTION
MARK
CUSHION UPPER
INDIVIDUAL CARTON
JOINT
KDL-40/46/52W4000 (AUS)
4-13E
9-888-209-02
Sony EMCS Corporation
Inazawa TEC
English
2008HL08-Data
Made in Japan
 2008. 8
KDL-40/46/52W4000 (AUS)
55