Complex Engineering Problem /Assignment 2
Last date of submission=19.3.2024 04:00pm
Late submission accepted till:21-3-2024 @12:30pm
CLO 2 PLO 2
Max Marks:=20
Section B
Section A
Regis tration No.
Nam e
Proble m
Group #
Regis tration No.
Nam e
1
MUST/FA20-BME-001/AJK
Abdul Hannan Khalid
1
MUST/FA20-BME-041/AJK
Anib Farooq
2
MUST/FA20-BME-003/AJK
Abdullah
2
MUST/FA20-BME-042/AJK
Aqeel Rasheed
3
MUST/FA20-BME-005/AJK
AHSAN FAROOQ
3
MUST/FA20-BME-044/AJK
Fahad Zubair
4
MUST/FA20-BME-006/AJK
ALI MUNIR
4
MUST/FA20-BME-045/AJK
Hamid Ali
5
MUST/FA20-BME-008/AJK
Asad
5
MUST/FA20-BME-046/AJK
Muhammad Ahmed Raza Janj ua
6
MUST/FA20-BME-009/AJK
Danish Hafeez
7
MUST/FA20-BME-010/AJK
DAW OOD W ASIM ABBASI
6
MUST/FA20-BME-048/AJK
Muhammad Ali
8
MUST/FA20-BME-011/AJK
Hammad Ahmed
7
MUST/FA20-BME-049/AJK
Muhammad Atif Razzaq
9
MUST/FA20-BME-012/AJK
Hamza Mustafa
8
MUST/FA20-BME-050/AJK
Muhammad Daw ood kiani
10
MUST/FA20-BME-014/AJK
Hassan Yar Chughtai
9
MUST/FA20-BME-052/AJK
MUSTAFA AMJAD
11
MUST/FA20-BME-015/AJK
HUSSNAIN ZAIB MUGHAL
10
MUST/FA20-BME-054/AJK
Perv aiz Abbas
12
MUST/FA20-BME-016/AJK
KHAW AJA BASHARAT MAQBOOL
13
MUST/FA20-BME-017/AJK
MIRZA MUHAMMAD HAMMAD BAIG
11
MUST/FA20-BME-056/AJK
Sajid Ali
14
MUST/FA20-BME-018/AJK
Muhammad Awais
12
MUST/FA20-BME-058/AJK
Syed Areez Haider Gardezi
15
MUST/FA20-BME-019/AJK
Muhammad Ikram
13
MUST/FA20-BME-060/AJK
Asad Qayyum
16
MUST/FA20-BME-020/AJK
Muhammad Maaz Javed
14
MUST/FA20-BME-061/AJK
Ghulam-E-Mustafa
17
MUST/FA20-BME-021/AJK
Muhammad Saad Bin Saeed
15
MUST/FA20-BME-063/AJK
Muhammad Sohail Shehzad
18
MUST/FA20-BME-023/AJK
Noman zahid
19
MUST/FA20-BME-024/AJK
Nouman Nisar
20
MUST/FA20-BME-025/AJK
SAJJAD UL HASSAN
21
MUST/FA20-BME-027/AJK
Shaaf Ahmed Sheikh
22
MUST/FA20-BME-028/AJK
23
MUST/FA20-BME-029/AJK
24
Mechanical Engineering Department MUST want to install hydraulic hammer with following specification in its workshop
Weight 600Lbf height 5 ft maximum beat frequency 800/min. Design base so that transmissibility ratio shall not exceed than 0.1.
Security Head MUST wants to install a security camera on roof top of MED for vigilance outside the University it will subject to a
continuous wind load of Fo sinωt, where the peak force measured is 15 N. The wind frequency is about 06 Hz and the camera mass is
4 kg. The mounting bracket is made of aluminum with square cross-section (25mm×25mm). Ignoring damping, determine the desirable
length of the mounting bracket that will keep the vibration amplitude equal or less than 4 mm.
An industrial sewing Machine has amass of 400 kg and operates at 2000 RPm its observed that it apperas to have a rotary unbalance of
100kg.cmstructural engineers suggests that the max repeated force should transmitted to the floor is 85kN. The isolator available has
stifness K and a damping ratio of 0.2 It that is placed between machine and floor Determine the value of K that will keep the force below
acceptable limit .
1
2
3
6
MUST/FA20-BME-064/AJK
Raja Hamad Ullah Rafique
17
MUST/FA20-BME-065/AJK
sami ul hassan
18
MUST/FA20-BME-066/AJK
Shoaib Idrees
Shah Hassan
19
MUST/FA20-BME-067/AJK
Tallal Tassadaq Khan
Shahbaz Ahmed
20
MUST/FA20-BME-068/AJK
Sohaib Imran
MUST/FA20-BME-030/AJK
Sharyar Sajid
21
MUST/FA20-BME-069/AJK
Hammad Bin Khalid
25
MUST/FA20-BME-031/AJK
Shayan Ishfaq
22
MUST/FA20-BME-070/AJK
Hassan Naveed
26
MUST/FA20-BME-033/AJK
Syed Rohan Murtaza
23
MUST/FA20-BME-071/AJK
HUZAIFA KHURSHID
27
MUST/FA20-BME-034/AJK
Talha Shabbir
24
MUST/FA20-BME-072/AJK
Waseem Anjum
28
MUST/FA20-BME-035/AJK
W aqar Hussain
25
MUST/FA20-BME-073/AJK
Fahad Subhani Sarwar
29
MUST/FA20-BME-036/AJK
Zain Nawaz
6
MUST/FA20-BME-074/AJK
Sahad Ahmed Khokhar
30
MUST/FA20-BME-037/AJK
Zaryab Zafar
27
MUST/FA20-BME-075/AJK
31
MUST/FA20-BME-038/AJK
Zran azeem
28
MUST/FA20-BME-076/AJK
Syed Muhammad Noman Shah
32
MUST/FA20-BME-039/AJK
Abdul Rehman
29
MUST/FA20-BME-077/AJK
Sayyaf Zahid
33
MUST/FA20-BME-040/AJK
Ahmad Rehan
30
MUST/FA20-BME-078/AJK
Shahzar Mehm
4
5
Analyze the following linear mass-spring vibration system and determine the natural frequencies of the system by using Holzer method.
Note
Note :- No submition after 21-3-2024 @1pm
Muhammad Noman Iqbal
6
Group 5 has same question as of Group 4 with following specs
Mass=200kg, Unbalance =0.3kgm, beam length 3.5m, speed of machine=2000RPM (remaining values are same)