Nokia Networks
GSM/EDGE BSS, Rel. GSM 16,
Operating Documentation,
Issue 03
General Error Messages of
System
DN987378
Issue 30-0
General Error Messages of System
The information in this document applies solely to the hardware/software product (“Product”) specified
herein, and only as specified herein.
This document is intended for use by Nokia Solutions and Networks' customers (“You”) only, and it may not
be used except for the purposes defined in the agreement between You and Nokia Solutions and Networks
(“Agreement”) under which this document is distributed. No part of this document may be used, copied,
reproduced, modified or transmitted in any form or means without the prior written permission of Nokia
Solutions and Networks. If you have not entered into an Agreement applicable to the Product, or if that
Agreement has expired or has been terminated, You may not use this document in any manner and You
are obliged to return it to Nokia Solutions and Networks and destroy or delete any copies thereof.
The document has been prepared to be used by professional and properly trained personnel, and You
assume full responsibility when using it. Nokia Solutions and Networks welcome Your comments as part of
the process of continuous development and improvement of the documentation.
This document and its contents are provided as a convenience to You. Any information or statements
concerning the suitability, capacity, fitness for purpose or performance of the Product are given solely on
an “as is” and “as available” basis in this document, and Nokia Solutions and Networks reserves the right
to change any such information and statements without notice. Nokia Solutions and Networks has made all
reasonable efforts to ensure that the content of this document is adequate and free of material errors and
omissions, and Nokia Solutions and Networks will correct errors that You identify in this document. But,
Nokia Solutions and Networks' total liability for any errors in the document is strictly limited to the correction
of such error(s). Nokia Solutions and Networks does not warrant that the use of the software in the Product
will be uninterrupted or error-free.
NO WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
ANY WARRANTY OF AVAILABILITY, ACCURACY, RELIABILITY, TITLE, NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RELATION TO THE
CONTENT OF THIS DOCUMENT. IN NO EVENT WILL NOKIA SOLUTIONS AND NETWORKS BE
LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF
PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY
ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT, EVEN IN THE CASE OF
ERRORS IN OR OMISSIONS FROM THIS DOCUMENT OR ITS CONTENT.
This document is Nokia Solutions and Networks’ proprietary and confidential information, which may not be
distributed or disclosed to any third parties without the prior written consent of Nokia Solutions and
Networks.
Nokia is a registered trademark of Nokia Corporation. Other product names mentioned in this document
may be trademarks of their respective owners, and they are mentioned for identification purposes only.
Copyright © 2016 Nokia Solutions and Networks. All rights reserved.
f
Important Notice on Product Safety
This product may present safety risks due to laser, electricity, heat, and other sources of danger.
Only trained and qualified personnel may install, operate, maintain or otherwise handle this
product and only after having carefully read the safety information applicable to this product.
The safety information is provided in the Safety Information section in the “Legal, Safety and
Environmental Information” part of this document or documentation set.
Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of its
products and services. We would like to encourage you as our customers and users to join us in working
towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations
for power use and proper disposal of our products and their components.
If you should have questions regarding our Environmental Policy or any of the environmental services we
offer, please contact us at Nokia Solutions and Networks for any additional information.
2
DN987378
Issue: 30-0
General Error Messages of System
Table of Contents
This document has 979 pages
Issue: 30-0
1
General error messages................................................................ 4
2
Error messages.............................................................................. 5
DN987378
3
General error messages
General Error Messages of System
1 General error messages
The general error messages are listed here in numerical order.
During an MML session, the user can see the explanation of an error that has occurred,
together with instructions (if any) how to proceed, by pressing the character combination
CTRL-7. In addition, the user can search for the explanation of an error message by
means of the service terminal extension MRSTRE.
As this list contains the general execution error messages of all applications, it is
possible that it will also include messages that do not belong to the configuration of a
particular customer.
Error code values greater than 0x7fffffff = 2147483647 are application specific. They are
described in the application specific documents. The user cannot see the explanation of
these codes by using CTRL-7 or MRSTRE as given above.
4
DN987378
Issue: 30-0
General Error Messages of System
Error messages
2 Error messages
0
SUCCESS
The operation succeeded completely.
1
NO SUCH FILE
The file does not exist.
2
FILE READ PROTECTED
The file is read protected.
3
OFFSET OUT OF FILE
The offset points out of the file.
4
OFFSET OUT OF RECORD
The offset points out of the record.
5
RECORD NUMBER OUT OF FILE
The number of the record is equal to or greater than the
number of records in the file.
6
SUBRECORD NUMBER OUT OF RECORD
The number of the subrecord is equal to or greater than
the number of subrecords in the file.
7
SEARCH KEY NOT FOUND
The search key is not found in the file.
8
FILE ALREADY EXISTS
The file already exists.
9
NOT IMPLEMENTED
The feature has not been implemented.
10
INCORRECT FILE HANDLE
The file handle is incorrect.
11
INCORRECT FILE TYPE
The type of the file is unknown, or it does not fit in the
situation.
12
FILE HAS NO BITMAP
The file has no bitmap.
13
Issue: 30-0
POINTER TO FILE DEFINITION STRUCTURE IS NULL
DN987378
5
Error messages
General Error Messages of System
The pointer to the structure defining the characteristics of a
file is null.
14
INCORRECT FILE DEFINITION STRUCTURE
The structure defining the characteristics of a file is
incorrect.
15
INCORRECT ACCESS MODE
The access mode is forbidden or unknown.
16
FILE CATALOG FULL
The file catalog is full.
17
PROCESS LDT FULL
The LDT (local description table) of the process is full.
18
MEMORY ALLOCATION ERROR
An error has occurred in the allocation of memory space.
19
FILE WRITE PROTECTED
The file is write protected.
20
INCORRECT FILE BLOCK NUMBER
The number of the file block is incorrect.
21
NO BLOCK CHECK SUM IN FILE
The file has no block-specific check sums.
22
NULL POINTER TO PARAMETER
The pointer to the parameter is null.
23
ARRAY REALLOCATION ERROR
An error has occurred in the array reallocation.
24
RECORD IS FREE
The record is free.
25
RECORD IS NOT FREE
The record is not free.
26
END OF FILE CATALOG
The file catalog has ended.
27
6
CHECK SUM CALCULATION FAILURE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The calculation of the check sum failed (file was updated
during the calculation).
28
PCMCON GSW ERROR
The PCMCON file of the group switch is incorrect.
29
FILE DISTRIBUTION TIME-OUT
The time limit of file distribution has expired.
30
FILE DISTRIBUTION ERROR
An error has occurred in file distribution.
31
UNIT TYPE ACCESS ERROR
An error has occurred in conversions between the unit
type, logical address and message bus address.
32
FLOPPY DISK CONTROLLER BUSY
The floppy disk controller has not returned to its original
state after the previous disk operation. The floppy disk
controller is faulty. Restart the EDISKD program block.
Replace the DMADI plug-in unit.
33
FLOPPY DISK CONTROLLER IN RESULT PHASE
The floppy disk controller is in result phase. A new
command is given when the previous command is still in
result phase. There is a disturbance in the EDISKD
program block or the floppy disk controller is faulty. Restart
the program block EDISKD. Replace the DMADI plug-in
unit.
34
FLOPPY DISK CONTROLLER IN COMMAND PHASE
The floppy disk controller is in the command phase. The
floppy disk controller waits for a new command while an
attempt is made to read the result of the previous
command from it. There is a disturbance in the EDISKD or
the floppy disk controller is faulty. Initialize the floppy disk
controller again. Replace the DMADI plug-in unit.
35
EQUIPMENT CHECK ERROR
The disk drive has given an error signal or the 0 cylinder is
not reached in the recalibration command after 77 step
pulses. The disk drive or the floppy disk controller is faulty.
Replace the disk drive. Replace the DMADI plug-in unit.
36
DRIVE NOT READY
The disk drive is not capable of executing a new disk
operation. The operator tries to read the empty side of a
single-sided disk or write on an empty side of a single-
Issue: 30-0
DN987378
7
Error messages
General Error Messages of System
sided disk. The disk type is not correct, the disk does not
exist, the door of the disk drive is open, there is no power
in the disk drive, the disk drive does not exist, the disk
drive is faulty or the floppy disk controller is faulty. Check
the disk. Close the door of the disk drive. Check the disk
drive and change it if necessary. Replace the DMADI plugin unit.
37
RECALIBRATE ERROR
The transfer of the read/write head of the disk drive to the
0 track has failed. Replace the disk drive. Replace the
DMADI plug-in unit.
38
SEEK ERROR
The search for a track or a sector has failed. The disk drive
or the floppy disk controller is faulty. Replace the disk
drive. Replace the DMADI plug-in unit.
39
END OF TRACK ERROR
The floppy disk tries to direct a command to a sector
whose number is higher than that of the last sector of the
track. There is a disturbance in the EDISKD program block
or the floppy disk controller is faulty. Restart the EDISKD
process. Replace the DMADI plug-in unit.
40
CRC ERROR IN DATA
There is a CRC error in the data field of the sector. The
disk is faulty. Replace the disk.
41
CRC ERROR IN ID
There is a CRC error in the ID field of the sector. The disk
is faulty. Replace the disk.
42
LATE DMA
The DMA controller does not receive permission for DMA
transfer in time. The DMA controller is faulty or the
administration logic of the bus is faulty. Replace the
DMADI plug-in unit. Replace the CPU386 plug-in unit.
43
SECTOR NOT FOUND
The floppy disk controller does not find the sector required.
The disk is faulty or the floppy disk controller is faulty.
Replace the disk. Replace the DMADI plug-in unit.
44
DISK WRITE PROTECTED
The disk is write protected. Remove write protection.
45
8
MISSING DATA ADDRESS MARK
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The floppy disk controller does not find the data address
mark on the required track. The disk or the floppy disk
controller is faulty. Replace the disk. Replace the DMADI
plug-in unit.
46
MISSING ID ADDRESS MARK
The floppy disk controller does not find the ID address
mark on the required track. The disk or the floppy disk
controller is faulty. Replace the disk. Replace the DMADI
plug-in unit.
47
CONTROL MARK
A deleted data address mark has been read during a
reading operation. The disk is faulty. Replace the disk.
48
CYLINDER ADDRESS ERROR
The cylinder address of the ID field of the sector differs
from the current cylinder address maintained by the floppy
disk controller. There is a disturbance in the program block
EDISKD, the disk is faulty or the floppy disk controller is
faulty. Initialize the floppy disk controller again. Replace the
disk. Replace the DMADI plug-in unit.
49
BAD SECTOR
Floppy disk: The cylinder address of the ID field of the
sector is 0FFH. The disk is faulty. Replace the disk.
Winchester: The disk operation has been directed to a
track which has been marked bad.
50
INCORRECT TASK
Incorrect command. The program block EDISKD does not
recognize the task given. The application program is faulty.
Check the application program.
51
NO EQUIPMENT
There is no equipment. There are no disk drives connected
to the DMADI plug-in unit, or the cable between the
DMADI and the disk drive has been accidentally
disconnected. Connect the cable.
52
INCORRECT PARAMETER IN TASK
The parameter is incorrect. One of the parameters of the
parameter block is incorrect. The application program is
incorrect. Check the application program.
53
Issue: 30-0
END OF DISK FOUND
DN987378
9
Error messages
General Error Messages of System
The last sector of the disk has been reached. An attempt is
made to read from the disk (absolute reading) or to write
onto the disk (absolute writing) past the end of the disk.
The reading or writing is ended in the last sector. An
attempt is made to write outside the memory of the disk.
54
COMMAND NOT ALLOWED ON OLD FORMAT DISK
The command is not allowed on the disk of the old format.
Do not give this command.
55
FORMAT ERROR
Floppy disk: The formatting of the disk has failed. The disk
is faulty. Replace the disk. Winchester: The read/write
head of the disk drive stays on the track on which the
formatting has failed. Mark the track bad and format the
alternative track.
56
NO SUCH FILE
The file specified by the parameter block is not found on
the disk. The disk is incorrect or the application program is
faulty. Replace the disk. Check the application program.
57
LABEL IS THE ONLY ONE
An attempt has been made to delete the only label of the
disk file.
58
FILE WRITE PROTECTED
The file is write protected.
59
FILE ALREADY UNPROTECTED
The file is already unprotected through another label.
60
FILE ALREADY EXISTS
The file already exists.
61
END OF DATA FOUND
The last data sector of the file has been reached. An
attempt is made to read the file past the end of the data.
The reading is ended in the last data sector.
62
NO DATA TO READ
There is no data to read. The file is empty or the read
pointer of the parameter block points past the end sector of
the file data.
63
10
END OF FILE FOUND
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The last sector of the file has been reached. An attempt is
made to write past the end of the file. The writing is ended
in the last sector.
64
FILE FULL
The file is full.
65
FILE TOO BIG
An attempt has been made to create a file which requires
too much memory space. Pack the disk. Reduce the
memory reservation of the file.
66
DISK FULL
The disk is full. All file labels of the disk are in use.
67
TOO MANY CRC ERRORS
The CRC counter of the disk has reached the maximum
value. Replace the disk.
68
DMA TERMINATION ERROR
The DMA transfer has been shorter than expected.
Replace the DMADI plug-in unit.
69
TIME-OUT ERROR
The device has not responded within the given time. Carry
out periodic maintenance and replace the used media if
necessary. If the problem re-occurs, check the device,
used media, cabling and controller.
70
INCORRECT COMMAND
The command code of the parameter block is unknown.
71
WRITE BLOCK TOO SHORT
The length of the block to be written is shorter than 4, and
blocks shorter than 4 cannot be written on the tape. Load
the MML and try again.
72
MULTIFILE NOT ALLOWED
An attempt has been made to open a file on a one-file tape
with a multifile opening command or quick file opening
command. When necessary, change the tape type into a
one-file tape and try again.
73
TRACK WRITE PROTECTED
Reel-to-reel tape unit (MTU) is write protected. Remove
the protection unless there is a reason for it.
Issue: 30-0
DN987378
11
Error messages
General Error Messages of System
74
ONE FILE TAPE
An attempt has been made to direct to a one-file tape one
of the following commands which can be directed only to
multifile tapes: premark tape, close file quickly, close
multifile, search for HDR1 block or search for file. Replace
the tape with a multifile tape and give the command again.
75
CORRECTED ERROR
The formatter has detected an error in connection with a
reading or writing operation. The error has been corrected
and data can be read from the tape.
76
TAPE MARK READ
The block read was a tape mark. Repeat the MML
command. If the error occurs again, clean the read head of
the drive and change the tape reel.
77
VERIFY ERROR
The data has not been written on the tape. The fault is
either in the reel-to-reel tape unit or in the RAM. Locate
and replace the faulty unit.
78
CRC ERROR
Despite repeated attempts writing fails due to a fault in the
tape or in the read head. Clean the read head of the reelto-reel tape unit or replace the tape with a new one.
79
LATE DMA
The DMA circuit of the DMADI has not transferred data
between the MTU and the RAM. The fault is either in the
TAPI, DMADI or CPU386 plug-in units. Highest probability
is that the fault is in the DMADI. Replace the faulty unit.
80
DRIVE NOT READY
The reel-to-reel tape unit is not ready to receive
commands. There is a hardware fault in the drive. Try
again in 3-4 minutes.
81
FORMATTER BUSY
The reel-to-reel tape unit is executing a command. A new
command has been given before the previous one has
been acknowledged. The operating system is faulty.
Locate the fault, initialize the TAPEDR program block if
necessary.
82
12
ACCESSED DRIVE OFF LINE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The reel-to-reel tape unit given in the MML command is in
the OFF LINE state. Press the ON LINE button on the front
panel of the unit.
83
PHYSICAL END
The end mark of the tape has been detected. If the tape
should not be at the end, check the condition of the tape
and, when necessary, clean the read head and change the
tape.
84
WRITE SECTION NOT FOUND
No write section is found in the reel-to-reel tape unit
specified in the MML command. Open the tape.
85
FILE TRANSFER SYSTEM BUSY (PROGRAM BLOCK
MEMDAT)
The program block MEMDAT is not capable of receiving
new tasks. Try again.
86
FILE TRANSFER SYSTEM BUSY (PROGRAM BLOCK
DUMPER)
The program block DUMPER is not capable of receiving
new tasks. Try again.
87
FILE TRANSFER SYSTEM BUSY (PROGRAM BLOCK
FULLER)
The program block FULLER is not capable of receiving
new tasks. Try again.
88
FILE TRANSFER SYSTEM BUSY (PROGRAM BLOCK
LOADER)
The program block LOADER is not capable of receiving
new tasks. Try again.
89
FILE TRANSFER SYSTEM BUSY (PROGRAM BLOCK
UPDATE)
The program block UPDATE is not capable of receiving
new tasks. Try again.
90
LOADING ABORTED
The program block DUMPER has interrupted the loading
of the files due to a loading error. Try again.
91
ERROR IN LOADING MESSAGE
There is an error in the loading message. The loading
message has been distorted on the message bus. Try
again.
Issue: 30-0
DN987378
13
Error messages
General Error Messages of System
92
END OF FILE FOUND
The file is loaded up to the end mark. The file to be loaded
is shorter than indicated by the program block which has
requested the loading. The situation is normal if the
MEMDAT program block has been requested to update the
whole file.
93
INCORRECT FILE NUMBER
The file number is incorrect. Check that the file number is
correct and that it belongs to the files of the source unit or
the target unit.
94
NO RESPONSE
No acknowledgement is received from the LOADER
program block to a loading message. Check the operation
of the ASS bus and the LOADER program block.
95
LENGTH ERROR IN LOADING
Loading error. Check that the number of bytes to be
updated which is given to the MEMDAT program block is
no larger than the file length.
96
NO MESSAGE
No message was received by the program block.
97
INCORRECT MESSAGE
The program block does not recognize the task identifier.
98
UNUSABLE STORE
Reading or writing on the disk is not possible. Check that
the disk drive is in order and in correct state.
99
DUMPING ABORTED
The sending of files has been interrupted.
100
BEGIN OF TAPE
The tape is at the beginning: A new tape has been inserted
into the tape unit or the tape unit has been set in the OFF
LINE state with operating switches although the unit
should be in the ON LINE state.
101
TIME-OUT ERROR (2)
The TAPEDR program block has been waiting for an
interrupt but it has not arrived within the time limit. (The
length of timeout supervision is 3-15 seconds, 3 minutes in
rewinding.) Cause for the error: 1. The cable of the
interrupt line between the TAPI and CPU386 plug-in unit is
14
DN987378
Issue: 30-0
General Error Messages of System
Error messages
broken or connected to a wrong pin. 2. The program block
has set the address of the interrupt service program
incorrectly in the interrupt vector table. 3. The tape unit has
moved into the OFF LINE state, possibly because of a
disturbance. 4. The tape unit is faulty. 5. The magnetic
tape is faulty. Check the items above.
102
WRITE BLOCK TOO LONG
An attempt has been made to write too long a data block
on the I/O device. Correct the error in the application
process.
103
DUPLICATE PREFORMATTING
An attempt has been made to format a tape already
formatted.
104
NOT AT BEGINNING OF TAPE
The tape is not at the beginning as it should be in
connection of the formatting and opening commands.
Rewind the tape to the beginning.
105
IDENTIFICATION FAILURE
An attempt is made to open a formatted tape with an
incorrect identifier (ID). Check the identifier.
106
PREFORMAT MISSING
The opening command has been given for a tape which
has not been formatted. Format the tape.
107
MULTIFILE TAPE
An error occurs when a command is given which is
allowed only to one-file tapes and there is a multifile tape
in the tape unit. Check the tape type and change it when
necessary.
108
TAPI UNIT FAILURE
There is a fault in the TAPI plug-in unit. Change the TAPI
plug-in unit.
109
DMA UNIT FAILURE
Before a reading or writing task is executed the TAPEDR
program block checks in the DMADI plug-in unit the DMA
channels which have been reserved for data transfer. If an
error is detected, the command will not be executed but a
failure status will be returned. Change the DMADI plug-in
unit.
110
Issue: 30-0
DATE NOT EXPIRED
DN987378
15
Error messages
General Error Messages of System
An attempt has been made to format a tape with an HDR1
label whose date has not expired. Release the tape or take
another tape into use.
111
FORMAT ERROR
The start block is faulty on the track to be closed. The track
close task has been directed to a faulty track. Give a new
command to the correct track.
112
PRINTER FAILURE
The printer is out of order. Check the printer and the printer
cable.
113
SERO BOARD MISSING
The SERO unit of the printer interface is missing or faulty.
Check that the SERO unit is in its place and functioning.
114
SERO BOARD FAILURE
The SERO unit of the printer interface is faulty. Check the
functioning of the SERO unit and replace it if necessary.
115
I/O DEVICE IN INCORRECT WORKING STATE
Operation has been directed to an I/O device that is not in
the WO state. Check the working state of the I/O device
and set it into the WO state if necessary.
116
TAPE CHANGE TIME-OUT
A tape change command has been given but the new tape
has not been installed quickly enough. Preformat and open
the new tape.
117
INCORRECT PARAMETER IN TASK
The object data (tape unit number, tape reel, or file name)
in the task is incorrect. Correct the object data (application
program or logical file incorrect).
118
INCORRECT NUMBER OF DRIVE
The device corresponding to the tape unit index in the task
has not been included in the software package in question.
Correct the tape unit index or software package so that the
required tape unit is included.
119
INCORRECT NAME OF TAPE FILE (ALREADY IN USE)
The file name defined in the MML command is already in
use in another tape unit. Open the tape file with a name
which is not yet in use.
120
16
INCORRECT NAME OF REEL (ALREADY IN USE)
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The name of the tape reel given in the MML command is
already in use in another tape unit. Preformat the tape by
using a name which is not yet in use.
121
COMMAND NOT ALLOWED IN THIS TAPE STATE
The MML command is not allowed in the current state of
the tape. Correct the working state of the tape. If the tape
unit is blocked, it must be set in the ON LINE state again.
122
CHECKSUM ERROR IN SYSTEM MONITORING
MESSAGE
The checksum in the message between the OSMONI
program block and the application program is incorrect.
Repeat the command.
123
WRONG MEMORY OR I/O ADDRESS
The program block OSMONI tries to handle an incorrect
memory area. (Write on ROM, no memory area, no input
port, etc.) Change the address.
124
MEMORY LACKING IN GIVEN ADDRESS
There is memory space only in part of the area to be filled.
125
PROCESS NOT IN DXPARA
The process identifier is incorrect. Check the process
identifier.
126
ASS UNIT BUSY
An attempt is made to write on the memory of the ASS3
(DX 210). An attempt is made to write on the active side of
the ASS0-ASS2 memories. It is not possible to write on the
memory of the ASS3. Perform switchover.
127
NO RESPONSE FROM PREPROCESSOR
The preprocessor does not respond within time limit.
Check that the plug-in unit exists. Try again.
128
TIME LIMIT EXCEEDED IN LOADING
MMIMAN has not received a response to a link or load
message from IOMANA within the time limit when loading
the MML program, in parts, into the OMU or MSW memory.
Try again.
129
UNKNOWN COMMAND
The requested MML program is not in the MCOMND file or
MMIMAN has not accepted MCOMND in its validity
checks. Check the MCOMND file. Restart MMIMAN.
Issue: 30-0
DN987378
17
Error messages
General Error Messages of System
130
UNKNOWN COMMAND CLASS
MMIMAN does not recognize the requested command
class.
131
MML LOADING ERROR
The dynamic address data in the phased loading of the
MML program are not correct. Try again.
132
RESOURCE SHORTAGE
MMIMAN has been unable to reserve all necessary buffers
in the loading phase of an MML program. Try again.
133
MML LENGTH ERROR
The MML program on disk is too long for the area reserved
for MML programs. Shorten the MML program on disk.
134
CURRENTLY NO SPACE FOR NEW MML
The RAM areas reserved for MML programs are being
used by other MML programs and it is not possible to load
a new program. Try again.
135
TIME LIMIT EXCEEDED IN INQUIRY
MMIMAN has not received a response within the time limit
from IOMANA when inquiring about the MML program
length data. Try again.
136
MESSAGE LENGTH ERROR
Message length error noticed by an individual process.
NOTICE: THIS IS NOT A DMX ERROR.
137
GIVEN BUFFER IS NOT DIVISIBLE BY EIGHT BYTES
The given buffer is not divisible by eight bytes that is
required by algorithm in use.
138
TQM STILL USED BY SOME WBTSS
The TQM is still used by some WBTSs.
139
THE COUNT OF IUB TRANSPORT QOS-ENABLED
WBTS EXCEEDS THE LICENSE IUB TRANSPORT QOS
CAPACITY LIMIT
The count of Iub Transport QoS-enabled WBTS exceeds
the license Iub Transport QoS capacity limit.
140
THE STATE OF THE LICENSE IUB TRANSPORT QOS IS
OFF
The state of the license Iub Transport QoS is off.
18
DN987378
Issue: 30-0
General Error Messages of System
141
Error messages
DCH&HSDPA, HSDPA OR HSUPA SHOULD NOT EXIST
WHEN DCH&HSPA EXISTS
If DCH & HSPA exists, DCH & HSDPA, HSDPA or HSUPA
should not exist.
142
HSDPA OR HSPA SHOULD NOT EXIST WHEN
DCH&HSDPA EXISTS
If DCH & HSDPA exists, HSDPA or HSPA should not exist.
143
ALLOCATE ERROR
An allocate error noticed by an individual process. For
example, process RAM area overflow: NOTICE: THIS IS
NOT A DMX ERROR.
144
HSDPA OR HSUPA SHOULD NOT EXIST WHEN HSPA
EXISTS
If HSPA exists, HSDPA or HSUPA should not exist.
145
STRINGENT SHOULD BE INCLUDED IN ONLY ONE
PATH TYPE FOR SAME AAL2 UP USAGE
For the same AAL2 up usage in a CoCo, stringent should
be included in only one path type.
146
STRINGENT BI-LEVLE SHOULD BE INCLUDED IN ONLY
ONE PATH TYPE FOR SAME AAL2 UP USAGE
For the same AAL2 up usage in a CoCo, stringent bi-level
should be included in only one path type.
147
TOLERANT SHOULD BE INCLUDED IN ONLY ONE
PATH TYPE FOR SAME AAL2 UP USAGE
For the same AAL2 up usage in a CoCo, tolerant should
be included in only one path type.
148
STRINGENT OR STRINGENT BI-LEVEL DCH IS
MISSING FROM ROUTE
Stringent or stringent bi-level DCH is missing from route.
149
TOLERANT HSDPA IS MISSING IN BTS
Tolerant HSDPA is missing in BTS.
150
INVALID PARAMETER
A parameter noticed invalid by an individual process.
NOTICE: THIS IS NOT A DMX ERROR.
151
Issue: 30-0
AAL2 UP USAGE AND AAL2 PATH TYPE COMBINATION
IS ILLEGAL
DN987378
19
Error messages
General Error Messages of System
AAL2UP usage and AAL2 PATH TYPE combination is
illegal.
152
AAL2 PATH TYPES OF AN AAL2UPUSAGE ARE
OVERLAPPED
Aal2 path types of an aal2upusage are overlapped.
153
LCS SUPPORT FOR ANCHORING CAN BE ENABLED
ONLY WHEN PARAMETER LCS FUNCTIONALITY IS
ENABLED
LCS Support for Anchoring can be enabled only when
parameter LCS Functionality is enabled.
154
TIME LIMIT EXCEEDED IN MESSAGE WAITING
The time limit of message receiving has expired. Try again,
check the functioning of the partner program block.
155
LCS SUPPORT FOR ANCHORING CAN BE ENABLED
ONLY WHEN OPERATIONAL MODE IS RNC CENTRIC
MODE
LCS Support for Anchoring can be enabled only when
Operational Mode of LCS is RNC Centric Mode.
156
SINTERSEARCHCONN PARAMETER SHOULD BE
BETWEEN THE SINTRASEARCHCONN AND
SSEARCHRATCONN
The value of parameter SintersearchConn should be
between the parameters SintrasearchConn and
SsearchRATConn.
157
LHOWINSIZEONINTERFERENCE MUST BE EQUAL TO
OR GREATER THAN RRINDPERIOD IN WBTS CELL
Window size for interference measurement to start LHOs
must be equal to or greater than Radio Resource
Indication Period in WBTS cell.
158
LHOWINSIZEONINTERFERENCE CANNOT BE
SHORTER THAN PRX AND PTXTOTALREPORTPERIOD
IN NB/RSXXX CELL
Window size for interference measurement to start LHOs
must be equal to or greater than reporting periods for the
RTWP and the TCP measurements in NB/RSXXX cell.
159
MODIFICATIONS NOT ALLOWED
File modifications in the CMs are not allowed because
either the active or the passive CM is loading its files. Try
again.
20
DN987378
Issue: 30-0
General Error Messages of System
160
Error messages
AAL2 UP USAGE AND PATH TYPE COVERAGE
OVERLAPPED
AAL2 UP USAGE and Path Type Coverage overlapped.
161
IF DIRECTEDRRCFORHSDPALAYERENHANC IS
DISABLED, THERE CANNOT BE MORE THAN TWO
LAYERS
If DRRC connection setup for HSDPA layer enhancements
is disabled, there cannot be more than two layers in one
sector.
162
MISSING PRIMARY SPARE BCSU UNIT
PCU track configuration is asymmetrical and primary spare
BCSU unit definition is missing.
163
INVALID PRIMARY SPARE BCSU UNIT
CONFIGURATION
PCU track configuration is asymmetrical and primary spare
BCSU unit configuration is invalid.
164
WRONG PRIMARY SPARE BCSU UNIT STATE
Wrong primary spare BCSU unit state.
165
POSITION NUMBER RESERVED
The position number is already in use. Change the position
number.
166
FILE ERROR
An error has been found in the CM files while a command
is being executed. See the alarm 2060 CENTRAL
MEMORY FILE ERROR, /Failure Print-Outs, Alarm PrintOut Manual, 2.5/.Repeat the command.
167
GROUP CALL NUMBER WITH POSITION NUMBER
The given subscriber number is a group call number.
Check the subscriber number and use hunting group MML
commands if necessary.
168
EXTENSION OF HUNTING GROUP
The subscriber belongs to a hunting group. Check the
subscriber number and use hunting group MML
commands if necessary.
169
VIRTUAL CHANNEL CONNECTION TABLE IS FULL
The Virtual Channel Connection table is full.
170
Issue: 30-0
DISK NOT UPDATED
DN987378
21
Error messages
General Error Messages of System
No communication with the program block handling disk
update, or some other failure in disk update. See the alarm
1065 DISK UPDATE FAILURE, /Disturbance Print-Outs,
Alarm Print-Out Manual, 2.5/.
171
SPARE CM UNIT NOT UPDATED
The spare CM is not updated. See the alarm 1064 UNIT
UPDATE FAILURE, /Disturbance Print-Outs, Alarm PrintOut Manual, 2.5/.
172
VIRTUAL CHANNEL CONNECTION TABLE ENTRY
ALREADY EXISTS
The Virtual Channel Connection table entry already exists.
173
POSITION NUMBER VACANT
Check the position number.
174
VIRTUAL CHANNEL CONNECTION TABLE IS EMPTY
The Virtual Channel Connection table is empty.
175
VIRTUAL CHANNEL CONNECTION TABLE ENTRY
DOES NOT EXIST
The Virtual Channel Connection table entry does not exist.
176
INCORRECT FILE NUMBER
There is an incorrect or illegal file number in the counter
correction message. Repeat the command, check the
parameters.
177
FILE CATALOG ERROR
An error has been detected in file addressing. The file in
question is not found in the catalog or the addressing is
outside the catalog.
178
NONEXISTENT METER
The STATCO program block has received an incorrect
value for one of the following parameters in the meter
interrogation MML command: incorrect subscriber number,
incorrect circuit group number, incorrect charging zone
number, incorrect meter type or class. Repeat the
command, check the parameters.
179
IF NEIGHBOURINGRNWELEMENT IS SET TO FLEXI
DIRECT RNC, NRNCVERSION SHOULD BE SET TO
REL6 OR HIGHER
if neighboringrnwelement is set to Flexi Direct RNC,
nrncversion should be set to rel6 or higher
22
DN987378
Issue: 30-0
General Error Messages of System
180
Error messages
DLDC FEATURE IS NOT IN USE IN BSC
DLDC feature cannot be enabled due to that there is no
license installed in BSC or license has been expired or
license is in wrong state.
181
DLDC CAPACITY LICENSE EXCEEDED
Capacity of the DLDC license exceeded.
182
DLDC CANNOT BE ENABLED WITHOUT EGPRS
ENABLED IN BTS
DLDC cannot be enabled if EGPRS feature is not in use in
the BTS.
183
DLDC REQUIRES THAT TRACK CAN ONLY CONTAIN
PCU2-TYPE PCUS
DLDC cannot be enabled if the serving PCU and the whole
track contains other than PCU2-type PCUs.
184
FILE MARKED BAD
Operation has been directed to a disk file marked bad.
185
FILE LOCKED BY ANOTHER USER
File is locked. The user has no authority to read the file or
write in it.
186
DATA VERIFY ERROR
The data on disk does not correspond to the data in
memory. Writing on the disk has failed. The disk formatting
has failed.
187
ALTERNATE TRACK ERROR
No alternate track can be found for a track marked bad.
Format an alternate track.
188
DISK FULL
The disk is full.
189
NO INDEX PULSES
The disk controller does not detect disk index pulses. The
disk drive is faulty or the disk controller is faulty. Replace
the disk drive. Replace the disk controller.
190
NO SEEK COMPLETE
The read/write head of the disk drive does not move
correctly. The disk drive or the disk controller is faulty.
Replace the disk drive. Replace the disk controller.
Issue: 30-0
DN987378
23
Error messages
General Error Messages of System
191
WRITE FAULT
Writing on the disk fails. The disk drive or the disk
controller is faulty. Replace the disk drive. Replace the disk
controller.
192
DRIVE NOT SELECTED
The disk drive has not been specified in the command.
193
TRACK 0 NOT FOUND
The disk or the disk controller is faulty. Replace the disk
drive. Replace the disk controller.
194
ID FIELD READ ERROR
There is a disk ID field read error. If the error is repeated,
the disk drive or the disk controller is faulty. Mark the track
bad and format an alternate track. Replace the disk drive.
Replace the disk controller.
195
UNCORRECTABLE DATA ERROR
An error has been detected in the data to be stored on
disk. The error cannot be corrected by the disk controller.
Set the read/write head on the track again. If the error
does not disappear, mark the track bad and format an
alternate track.
196
TARGET SECTOR NOT FOUND
The required block cannot be found on the disk. Mark the
track on which the block is located bad and format an
alternate track.
197
DATA TRANSFER TIME-OUT
Data transfer between the disk controller and EDISKD has
exceeded the time limit. Replace the disk drive. Replace
the disk controller. Replace the DMADI plug-in unit.
198
ERROR BURST CORRECTED
The disk controller has detected and corrected incorrect
data.
199
ADJG GAN RELATED PARAMETERS NOT SAME WITH
RNC PARAMETERS GANetwARFCN, GANetwNCC AND
GANetwBCC
ADJG GAN related parameters are not the same with RNC
parameters GANetwARFCN, GANetwNCC and
GANetwBCC.
200
24
INVALID COMMAND
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The disk controller does not accept the command it has
received from EDISKD. Replace the disk controller.
201
INVALID SECTOR ADDRESS
Wrong block number. The disk controller has been given a
block number outside the memory. The disk has not been
initialized or the disk drive is faulty. Initialize the disk.
Replace the disk drive.
202
VOLUME OVERFLOW
EDISKD has given the disk controller a command, and the
value of the parameters is too high.
203
RAM FAILURE
The RAM of the disk controller is faulty. Replace the disk
controller.
204
ROM FAILURE
The ROM of the disk controller is faulty. Replace the disk
controller.
205
ECC HARDWARE FAILURE
There is an error in the correction logic of the disk
controller. Replace the disk controller.
206
GAN ADJG CAN EXIST ONLY WHEN GSM NEIGHBOUR
CELL IS NOT INCLUDED IN THE SYSTEM
INFORMATION
GAN ADJG can exist only when GSM neighbour cell is not
included in the system information.
207
SCSI BUS IS BUSY
The SCSI bus is busy.
208
NO RESPONSE FROM DMA
Writing on the DMA has failed. Replace the DMADI unit.
209
SENSE DATA TRANSFER FAILED
EDISKD has not received error status from the disk
controller. Replace the disk controller.
210
RESET UNSUCCEEDED
The disk controller reset has failed. Replace the disk
controller.
211
Issue: 30-0
SCSI BUS ERROR
DN987378
25
Error messages
General Error Messages of System
The cable between the DMADI plug-in unit and the
winchester disk controller is faulty. Faulty disk controller.
Replace cable. Replace disk controller.
212
PARITY ERROR
There is a parity error in the data transfer between the disk
controller and the DMADI plug-in unit. Try again.
213
ILLEGAL ALTERNATE TRACK ACCESS
The addressing of an alternate track is incorrect or the disk
operation has been directed to an alternate track directly
(without being first directed to a track marked bad).
214
INVALID ALTERNATE TRACK
The track has already been marked as an alternate track
for another track. Choose another alternate track.
215
ALTERNATE TRACK NOT ALTERNATE
An alternate track has been marked for a bad track but no
bit of the alternate track is found in the ID field of the
alternate track. Format the alternate track again.
216
BAD TRACK AS ALTERNATE
An attempt is made to mark a bad track as an alternate
track. Choose another alternate track.
217
WINCHESTER DISK CHECKSUM ERROR
There is an error in the checksum of the disk directory.
Initialize the disk.
218
EDISKD PROGRAM BLOCK BUSY
EDISKD is copying the disk; other application processes
cannot operate on the disk. Wait till the copying ends.
219
SEGMENT READ ERROR
An error has occurred during an attempt to read a
segment.
220
SEGMENT WRITE ERROR
An error has occurred during an attempt to write in a
segment.
221
ATTEMPT TO ACCESS ABOVE SEGMENT
An attempt has been made to access above segment.
222
ADJG BCCH ARFCN VALUE OUT OF RANGE
ADJG BCCH ARFCN value is out of range.
26
DN987378
Issue: 30-0
General Error Messages of System
223
Error messages
NO AVAILABLE UDP PORT FOR RESERVATION
No available UDP port for reservation.
224
NO SUCH I/O-DEVICE
An application program wants to operate on a device
(process) which does not exist on the given MSW level.
Give the logical file an I/O device that exists on the MSW
level in question.
225
NO SUCH MSW CONNECTION
Application program wants the execution on a higher MSW
level, which does not belong to this branch of network
(incorrect system identifier). Check the system identifier of
the I/O device and try again.
226
MSW TRANSMISSION ERROR
The NETCOM program block has failed to transmit data.
Try again if necessary.
227
LOGICAL FILE ALREADY EXISTS
Application program tries to create a logical file with a
name which already exists in the tables of IOMANA.
Change the name of the logical file to be created if you
want to create a new file, or try to delete the old one.
228
I/O-DEVICE CONNECTION FAILURE
Application program has chained too many logical files.
Change the I/O device connection of the logical file.
229
LEG OF ONE OWNER ID EXCEEDED THE MAX
NUMBER
Leg of one owner ID exceeded the max number.
230
NO SUCH LOGICAL FILE
Application program is trying to operate on a logical file
that does not exist. Give the right file number in the
command.
231
NO FREE BUFFER
The system cannot provide a buffer needed to perform the
task. Try again after a while.
232
UNDEFINED COMMAND
Command has not been defined.
233
Issue: 30-0
OVERLOAD IN I/O SYSTEM
DN987378
27
Error messages
General Error Messages of System
There is currently no space available in the tables of
IOMANA. Try again after a while.
234
TOO DEEPLY NESTED
There are too many levels in the chain of logical file
connections. Change the connections.
235
OBJECT NOT FOUND
The object (usually another logical file) connected to the
logical file is not found.
236
LOGICAL FILE COUNT EXCEEDED
An attempt has been made to create more logical files than
the space reserved for them allows. Remove unnecessary
logical files.
237
PATTERN MATCH ENGINE OF AAL2 ACCELERATOR
FPGA IS BUSY
Pattern Match Engine of AAL2 Accelerator FPGA is busy.
238
ILLEGAL DEVICE
An attempt has been made to give a task to a device for
which it is not allowed.
239
SPARE LOGICAL FILE ALREADY EXISTS
An attempt has been made to create a spare logical file for
a logical file which already has a spare logical file.
240
DEVICE NOT IN USE
The I/O device given in the task does not exist in the
system or it is not available. Check the working state of the
I/O device.
241
PREVIOUS RESERVER INCORRECT
The reserver of the device has been given incorrectly in
the command used for releasing an I/O device or for
changing the reserver. Check the parameters of the MML
command.
242
CHANGE IS NOT ALLOWED
Change is not allowed.
243
ILLEGAL COMMAND
The command cannot be executed because the device is
in wrong working state. Check the working state of the
device and change it if necessary.
28
DN987378
Issue: 30-0
General Error Messages of System
244
Error messages
DEVICE ALREADY RESERVED
An attempt was made to reserve a device that is already
reserved. Try again.
245
ILLEGAL UNIT
An attempt has been made to give the task to a computer
unit which is not found in the system.
246
CONTROLLED SWITCHOVER OF TBU NOT ALLOWED
BECAUSE TBU IS NOT SYNCHRONIZED TO ANY
REFERENCE
CONTROLLED SWITCHOVER OF TBU NOT ALLOWED
BECAUSE TBU IS NOT SYNCHRONIZED TO ANY
REFERENCE Controlled switchover of TBU is forbidden
because TBUs are not synchronized to any
synchronization reference. Correct the situation before
making switchover. You can do switchover using FCD
parameter in switchover command. Using FCD parameter
under this circumstance may cause significant disturbance
in network element's internal message connections. Worst
case scenario is system restart.
247
NOT BIG ENOUGH BUFFER
An attempt to read from a device more data than the
biggest possible buffer can hold.
248
CONTROLLED TRANSITION TO SP-EX STATE NOT
ALLOWED BECAUSE REDUNDANT TBU IS NOT YET
INITIALIZED
Controlled transition to SP-EX state is forbidden because
redundant TBU is not yet initialized. Typically, initialization
takes only a few seconds but under certain circumstances
initialization can take up to two minutes. You can execute
state transition using FCD parameter in state change
command. Using FCD parameter shall cause issue where
redundant TBU is not ready for switchover and thus not
fulfill definition of 2N redundant unit. Under these
circumstances, switchover of TBU may cause significant
disturbance in the network element's internal message
connections.
249
CONFIGURATION SET NOT ALLOWED
Disk configuration change is not allowed because e.g. both
disks are not in the normal working state.
250
NO PERMITTED
An attempt is made to delete a logical file created by
another programblock.
Issue: 30-0
DN987378
29
Error messages
General Error Messages of System
251
TIME-OUT ERROR IN I/O SYSTEM
Time limit set by the application program has expired
before the I/O program blocks have performed the task.
Try again.
252
BUFFER ALLOCATION ERROR
The allocation of the buffer was not successful.
253
NO DATA TO WRITE
There is not data to write.
254
LOGICAL FILE RESERVED
The logical file is reserved. Try again.
255
UNSUCCESSFUL
A general negative response to an interrogation task. This
is not an actual error, but a negative answer to an
interrogation, the alternative being the status SUCCESS.
256
PSN TUNNEL ALREADY EXISTS IN PSEUDO WIRE
CONFIGURATION
PSN tunnel already exists in Pseudo Wire Configuration.
257
INVALID SEMAPHORE NAME
The given semaphore name is not smaller than the
number of semaphores defined by parameters.
258
SEMAPHORE PROTECTION VIOLATION
An attempt has been made to use the semaphore in a way
that is not allowed to the caller according to the protection
parameters.
259
SEMAPHORE INITIALIZATION ERROR
An illegal attempt to initialize the semaphore. Only a nonnegative value can be initialized in the counter of the
semaphore, and only when the value already is nonnegative.
260
ENTER REGION ERROR
The primitive ENTER_REGION is called in a situation in
which there already are calls in the critical region. The
critical regions can not be chained.
261
EXIT REGION ERROR
The primitive EXIT_REGION is called in a situation in
which there are no calls in the critical region.
30
DN987378
Issue: 30-0
General Error Messages of System
262
Error messages
BUFFER SIZE ERROR
An attempt has been made to allocate a buffer of the size
of zero or a buffer bigger than the maximum theoretical
buffer size.
263
BUFFER NOT AVAILABLE
Buffer allocation was not successful within the defined time
limit.
264
NO FREE DESCRIPTOR SLOT
No free descriptor slot for the descriptor pointing to the
buffer was found in the area of the descriptor table
reserved for the dynamic use of the caller or defined
process.
265
HANDLE ERROR
The buffer chain of the caller or defined process does not
contain a buffer with the defined handle.
266
ERROR IN MESSAGE LENGTH
The length of the message is not within the allowed range.
267
INVALID COMPUTER IDENTIFICATION ERROR
The logical address or preprocessor address in the
computer field of the message header is greater than the
largest allowed address of this type.
268
COMPUTER DOES NOT EXIST
The combination of the index part in the logical address
and the distribution extent, in the computer field of the
message header, the preprocessor address or the physical
computer corresponding to the relative address referring to
the pair of the own computer has not been defined.
269
NO MBIF
Message transmission requires a message bus, but the
logical or physical message bus that should be used in
message transmission according to the computer field in
the header, has not been defined or it does not exist.
270
HAND NOT REACHABLE
An incorrect message transmission attempt to a hand in a
process familyin which no error message transmission to
the master is in use. The hand is free or it has not been
created (in a lightweight family), or the focus in its
message header and in the administration information do
not match (when the focus of process identifier is used in
the family).
Issue: 30-0
DN987378
31
Error messages
General Error Messages of System
271
MESSAGE QUEUE OVERFLOW
An attempt has been made to send a message to a
process the message queue length of which, after the
message transmission, would exceed the maximum value
defined when creating the process.
272
UNIT SEPARATED
The message transmission requires a message bus, but
the message bus interface unit used is not connected to
the bus.
273
TRANSMIT FIFO NOT EMPTY
A message could not be sent to the message bus since
the transmission buffer of the message bus interface unit is
not empty. The reason for the failure always is a hardware
fault.
274
BUS SENDING FAILED
An attempt to send a message to the message bus has
failed, e.g. since the receiving computer does not exist or it
is not connected to the message bus. The reason for the
failure can also be a hardware fault.
275
LAST BYTE FAIL
Message transmission to the message bus has failed at
the point of the last byte. The reason for the failure
probably is a hardware fault.
276
TRANSMIT FIFO NOT EMPTIED, NO FAIL DETECTED
An attempt has been made to transmit a message to the
message bus. The transmission buffer of the message bus
interface unit is not emptied within the time limit, and no
transmission fault has been detected.
277
BROADCAST FAILED
An attempt has been made to send a message to the
message bus with a general group address. The
transmission buffer of the message bus interface unit has
not been emptied within the time limit. When a general
group address is used, this error code is received instead
of error codes received in other transmission methods
(BUS SENDING FAILED, LAST BYTE FAIL and
TRANSMIT FIFO NOT EMPTIED, NO FAIL DETECTED).
278
32
NO ACKNOWLEDGEMENT TO REGISTERED MESSAGE
RECEIVED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
No acknowledgement to a registered message is received
from the computer at the point of which this status appears
in the acknowledgement message.
279
REGISTERED MESSAGE NOT OK
A registered message has not reached the intended
receiver in the computer to which the message was
addressed.
280
MESSAGE IS TOO LONG
The received message is longer than the defined size of
the message receiving area. In this case a part of the
message is copied into the receiving area, the rest of the
message will be lost.
281
DYNAMIC DESCRIPTOR SLOT RANGE DEFINITION
ERROR
The definition of descriptor slots reserved for dynamic use
of the processor is incorrect (CREATE_FIRST,
CREATE_PROCESS). The descriptor slots reserved for
dynamic use and defined in the loading module of the
extension program are not a subset of descriptor slots to
be used dynamically by the process
(EXECUTE_PROGRAM).
282
PRIORITY ERROR
The priorities defined for the process are not in the right
order, or the higher priority exceeds the maximum priority
of the family.
283
INVALID PROCESS IDENTIFICATION
The defined process identification is not smaller than the
number of processes in the family (lightweight processes
in the lightweight family).
284
PROCESS DOES NOT EXIST
The process of the given process identification does not
exist. The existence of the master, instead of the
lightweight hand, will be checked. The killing or restarting
of the process is possible only by using the creation name
of the process.
285
PROCESS ALREADY EXISTS
The process of the given process identification does exist.
The existence of the master, instead of the lightweight
hand, will be checked.
286
Issue: 30-0
INVALID FAMILY IDENTIFICATION
DN987378
33
Error messages
General Error Messages of System
The given family identification is not smaller than the
number of process families defined by parameters.
287
FAMILY DOES NOT EXIST ERROR
The process family of the given family identification does
not exist.
288
FAMILY ALREADY EXISTS
The process family of the given family identification already
exists.
289
MODULE NOT FOUND
The loading module given in the family record is not found
in the primary chain. The module is not loaded into the
computer, or its name field is incorrect.
290
MODULE TYPE ERROR
The loading module is not of the right type.
291
HAND GROUP COUNT CONFLICT
The family record and the loading module contain
contradictory data on the number of hand groups in the
family.
292
FAMILY ENVIRONMENT AREA SIZE ERROR
The size of the family environment, calculated according to
the data in the family record and loading module, is at least
4 giga bytes.
293
NO ROOM FOR FAMILY ENVIRONMENT AREA
In the computer, there is no big enough, uniform, free
memory space for family or extension environment.
294
PROCESS COUNT ERROR
The number of processes in the family (lightweight
processes in a lightweight family) counted according to the
information in the family record is at least 65535.
295
LDT SIZE ERROR
The number of LDT descriptor slots counted according to
the information in the family record and loading module is
smaller than 8192.
296
INVALID SELECTOR
The LDT selector in the family record or the selector of the
descriptor, set according to the descriptor parts in the
loading module, is illegal.
34
DN987378
Issue: 30-0
General Error Messages of System
297
Error messages
DESCRIPTOR SLOT IN USE
An attempt has been made to set a descriptor to a
descriptor slot already in use. All the descriptor slots,
reserved for dynamic use, must be free, as well.
298
DESCRIPTOR TYPE ERROR
An attempt has been made to set the segment descriptor
to IDT, or such a segment descriptor that is not accepted in
the DMX environment. The granularity bit may not be set
(the maximum size of a segment to be set is 1 megabyte),
and the data segment may not be downwards increasing.
299
LOCAL AREA ALLOCATION ERROR
There is not enough space in the family or extension
environment for a segment, for which a memory space is
allocated in connection with the setting of a descriptor. This
fault occurs only if an incomplete correction has been
made in order to change the size of a segment.
300
FAMILY NOT EMPTY
An attempt has been made to delete the environment of a
family that is not empty. The deletion of a family
environment is not possible if there are processes in the
family, or if a process in another family has changed its
name to one belonging to the family that is being deleted.
301
ILLEGAL ATTEMPT TO MODIFY DMXRTE PROCESS
FAMILY
An attempt has been made to delete a DMX family or to
modify it.
302
PROCESS FROZEN
An attempt has been made to send a message to a
process that is frozen due to an exceptional interruption
caused by it.
303
FREE EXTENDED MEMORY CHAIN ALREADY
INITIALIZED
Free extended memory chain was already initialized when
initialization was asked from the operating system.
304
NO FREE TIME LIMIT RECORDS
There are no free time limit records in the computer.
305
TIME LIMIT TO RESET NOT FOUND
The time limit to be reset was not found.
306
Issue: 30-0
TIME LIMIT TO READ NOT FOUND
DN987378
35
Error messages
General Error Messages of System
The time limit to be read was not found.
307
NO ROOM TO WRITE TIME LIMIT WARMING DATA
The defined area is not sufficient for copying the time limits
to be warmed up.
308
NO FREE TNSDL TIMER RECORDS
There are no free TNSDL timer records in the computer.
309
TNSDL TIMER TO RESET NOT FOUND
The TNSDL timer to be reset was not found.
310
TNSDL TIMER TO READ NOT FOUND
The TNSDL timer to be read was not found.
311
NO ROOM TO WRITE TNSDL TIMER WARMING DATA
The defined space is not sufficient for copying the TNSDL
timers to be warmed up.
312
NO FREE WAKE UP RECORDS
There are no free wake-up records in the computer.
313
WAKE UP TO RESET NOT FOUND
The wake-up to be reset was not found.
314
NO FREE TIMER SERVICE RECORDS
There are no free timer service records in the computer.
315
TIMER SERVICE TO RESET NOT FOUND
The timer service to be reset was not found.
316
LOGICAL BUS NOT DEFINED
The logical bus, required for message transfer, has not
been defined.
317
SORTER NOT DEFINED
The sorter, required when transferring messages, has not
been defined.
318
NO ROOM FOR ACKNOWLEDGEMENTS TO
REGISTERED MESSAGE
When sending a registered message, the space reserved
for computer unit-specific acknowledgements was
insufficient. The message-sending primitive is, therefore,
not collecting any acknowledgements.
36
DN987378
Issue: 30-0
General Error Messages of System
319
Error messages
FAMILY SERVICES IN USE
The use of the given primitive is not allowed in the process
using the family services of the General On-Line Library
(LIBGEN).
320
SETTING OF MESSAGE TRAFFIC MONITORING
FAILED
Both monitoring records are reserved.
321
RESETTING OF MESSAGE TRAFFIC MONITORING
FAILED
The process attempting to remove message traffic
monitoring had not set message traffic monitoring.
322
DEBUGGING SERVICE SET BY OTHER PROCESS
Setting the debugging service failed because some other
process already has set the service.
323
NO DEBUGGING SERVICE SET BY PROCESS
The process attempting to remove the debugging service
was not the one that had set it.
324
THE COMPUTER IS ALREADY STOPPED
Setting of debugging service failed because the computer
has already been stopped.
325
A PROCESS IS ALREADY STOPPED
Setting of debugging service failed because a process has
already been stopped.
326
INCORRECT FULL PROCESS ID
The primitive is directed to a process which is identified
with a concise process id. However, the name which the
process is using at the moment differs from the name
given, thus the primitive does not recognize it.
327
COMPUTER GROUP NOT FOUND
The record representing the computer group, and the data
of which the operating system primitive was to read or
modify, cannot be found in the group address table.
328
COMPUTER NOT FOUND FROM GROUP
The computer cannot be found in the group the caller of
the operating system primitive had given.
329
Issue: 30-0
NO ROOM FOR GROUP RECORD
DN987378
37
Error messages
General Error Messages of System
There is no room for the group record in the memory
space it was to be copied.
330
GROUP ADDRESS TABLE FULL
There is no room for a new or a bigger record in the group
address table.
331
MESSAGE ROUTING TABLE FULL
There is no room for a new record in the message routing
table.
332
NOT LOGICAL ADDRESS
A computer address that was to be logical is not logical.
333
NOT PHYSICAL ADDRESS
A computer address that was to be physical is not
physical.
334
WRONG MESSAGE
The operating system primitive received a wrong message.
335
NO ANSWER
The operating system primitive received no answer.
336
NOT DONE
The service that was asked by a call of an operating
system primitive was not executed.
337
PSEUDO WIRE (PW) ALREADY EXISTS IN
CONFIGURATION
Pseudo Wire (PW) already exists in Pseudo Wire
Configuration.
339
ADDRESS RANGES OVERLAP
The address range defined by the post office overlaps with
an address range defined earlier.
340
INVALID POST DISTRICT INDEX
The district index of the post office is invalid.
341
GENERAL GROUP DEFINITION ERROR
Error in general group definition: both general groups have
not been defined or own computer cannot be found in
either group.
342
38
ILLEGAL CALL PARAMETER USED IN SYNCHRONOUS
OR ASYNCHRONOUS INTERFACE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Illegal call parameter is used in synchronous or
asynchronous interface.
343
REQUESTED DSP SERVICE TYPE IS CURRENTLY
DISABLED IN SOME OR ALL DSP SERVICE POOLS
Requested DSP service type is currently disabled in some
or all DSP service pools.
344
VMGW DATA CORRUPTION IN BC2PRB
VMGW data corruption in BC2PRB.
345
VMGW DATA CORRUPTION IN HTAPRB
VMGW data corruption in HTAPRB
346
SISU NOT FOUND
SISU is not found.
347
SISU IS ALREADY BLOCKED
SISU LB is already in blocked state.
348
SISU IS ALREADY WORKING
SISU LB is already in working state.
349
MDCR OR UBRSHARE CANNOT BE UNSPECIFIED FOR
UBR PLUS VP OR VC
MDCR or UBRSHARE cannot be unspecified for UBR plus
VP or VC.
350
TARGET IS NOT A VIRTUAL UNIT
The target is not a virtual unit.
351
TARGET INDEX INVALID
The target index is invalid.
352
PARENT UNIT INVALID
The parent unit is invalid.
353
TARGET AND CHILD NOT MAPPED
Target and child is not mapped.
354
CHILD INDEX INVALID
Child index is invalid.
355
LOCAL RELATED UNIT INVALID
Local related unit is invalid.
Issue: 30-0
DN987378
39
Error messages
General Error Messages of System
356
IP ADDRESS EXISTS IN VLAN INTERFACE
IP address exists in VLAN interface.
357
PSN TUNNEL CANNOT BE FOUND IN PSEUDO WIRE
CONFIGURATION
The Packet Switched Network (PSN) tunnel cannot be
found in Pseudo Wire Configuration.
358
PSEUDO WIRE CANNOT BE FOUND IN PSEUDO WIRE
CONFIGURATION
Pseudo Wire (PW) cannot be found in Pseudo Wire
Configuration.
359
PSEUDO WIRE IS NOT IN DISABLED STATE AS IT
SHOULD BE
Pseudo Wire (PW) is not in disabled state as it should be.
360
PSN TUNNEL IS NOT EMPTY AND INCLUDES PSEUDO
WIRE(S)
The Packet Switched Network (PSN) tunnel is not empty
and includes Pseudo Wire(s).
361
ACTIVATE ASSOCIATION BY GIVING PRIO=YES WITH
THE OYH COMMAND
The state of an M3UA association in override mode can be
changed only if PRIO=YES for the association.
362
ILLEGAL AAL2 PATH TYPE COMBINATION FOR HSXPA
VCC UNDER ROUTE
Within one ATM route, HSxPA VCC which has either only
tolerant type or all AAL2 path types should be found.
363
VALUE OF FASTUETHRESHOLDBCC MUST BE
HIGHER THAN VALUE OF FASTUECANCELBCC
The value of the parameter
FastUEThresholdBestCellChange must be higher than the
value of FastUECancelBestCellChange.
364
APS LOGIC INITIALIZATION ERROR
APS logic for protection group in interface unit cannot be
initialized. This can happen, if spare unit is removed from
the configuration and created back again while there is/are
protection group(s) configured in the interface unit. The
spare interface unit is not allowed to start up in this case.
To initialize the protection group successfully, the working
unit must also be restarted. Also, if there is a protection
group in interface unit and spare unit is removed and
created back again, the SET port is automatically selected
40
DN987378
Issue: 30-0
General Error Messages of System
Error messages
in creation of spare unit so that internal SET ports in
protected interface units match with each other (first SET
in WO unit - first SET in SP unit and so on). If ports were
not matching earlier, the SDH fiber cable in spare unit must
be reconnected to port which is matching with working unit.
365
MISU IS NOT FOUND
MISU is not found.
366
LIBRARY PROGRAM IS NOT AVAILABLE
Library program is not available.
367
DSP BOOT FILE CONSISTENCY ERROR OR CRC
CHECKSUM FAILURE WAS DETECTED WHEN
ATTEMPTING TO START UP THE DSP
DSP boot file consistency error or CRC checksum failure
was detected when attempting to start up the DSP.
368
CONFIGURATION NOT ALLOWED TO PRIMARY SPARE
UNIT
Configuration not allowed to primary spare unit.
369
DMPG SWITCH IS ONGOING
DMPG switch is ongoing.
370
ADVANCED IN SPEECH ANNOUNCEMENTS ARE NOT
SUPPORTED, NO ENOUGH MEMORY EXISTS IN VANU
UNIT(S)
Advanced in speech announcements are not supported,
no enough memory exists in VANU unit(s).
371
PW PACKET PAYLOAD SIZE IS TOO BIG
PW packet payload size is too big, for example, the frame
amount of timeslots is more than 512.
372
THE LICENSE OF IBTS SHARING IS OFF
The license of IBTS Sharing is off.
373
IF MAXBITRATENRTMACDFLOW IS 13440KBPS,
THERE MUST BE ONE SPDSCHCODESET WHICH
CONTAINS 15 CODE SET
If MaxBitRateNRTMACdflow is 13440kbps, there must be
one SPDSCHCodeset which contains 15 code set.
374
Issue: 30-0
HSDPA14MBPSPERUSER AND RELEVANT LICENSE
MUST BE ENABLED BEFORE SETTING
MAXBITRATENRTMACDFLOW TO 13440KBIT/S
DN987378
41
Error messages
General Error Messages of System
Before setting MaxBitRateNRTMACdflow to 13440kbit/s,
HSDPA14MbpsPerUser and relevant license must be
enabled.
375
RECEIVED BOOT MESSAGE WITH INCORRECT
SEQUENCE NUMBER FROM DSP
The sequence number in boot packet acknowledgement
message from DSP is not what is expected.
376
NO ANSWER RECEIVED FROM RRA MASTER IN TIME
Timer for waiting an answer from rra master has expired,
and no answer has been received.
377
CELL SERVICE OR CCH SETUP FAILED IN L3; FAILURE
SOURCE COULD BE RRA, BRM, NBAP, NRM, RC3 or L2
Cell service or CCH setup failed in L3. Failure source
could be RRA, BRM, NBAP, NRM, RC3 or L2.
378
CELL STATE NOTIFICATION ERROR IN L3; FAILURE
SOURCE COULD BE RRA, BRM, RNC_RAB_COMMON
OR L2
Cell state notification error in L3. Failure source could be
RRA, BRM, RNC_RAB_COMMON or L2.
379
ENCODING OF EXTERNAL INTERFACE MESSAGE
FAILED IN L3
Encoding of external interface message failed in L3.
380
CCH RESERVATION RELATED BRM MESSAGE
WAITING TIME OUT IN L3 RRA PRB
CCH reservation related BRM message waiting time out in
L3 RRA PRB.
381
CELL/CCH RESOURCE RESERVATION RELATED
MESSAGE WAITING TIME OUT IN L3 RRA PRB
Cell/CCH resource reservation related message waiting
time out in L3 RRA PRB.
382
CCH RESERVATION RELATED MESSAGE WAITING
TIME OUT IN L3 RRA PRB
CCH reservation related message waiting time out in L3
RRA PRB.
383
INTERNAL ERROR IN CELL/CCH HANDLING L3 RRACMA HAND
Internal error in Cell/CCH handling L3 RRA-CMA hand
42
DN987378
Issue: 30-0
General Error Messages of System
384
Error messages
CELL SETUP OR COMMON TRANSPORT CHANNEL
RESERVATION-RELATED ERROR NOTICED IN NBAP
Cell Setup or Common Transport Channel reservationrelated error noticed in NBAP.
385
CELL OR COMMON TRANSPORT CHANNEL
RESERVATION-RELATED ERROR NOTICED IN NBAP
Cell or Common Transport Channel reservation-related
error noticed in NBAP.
386
CELL OR COMMON TRANSPORT CHANNEL
RESERVATION-RELATED ERROR NOTICED IN NBAP
PRB
Cell or Common Transport Channel reservation-related
error noticed in NBAP.
387
JITTER BUFFER SIZE IS TOO SMALL
Frame number of PW is bigger than jitter buffer size. Jitter
buffer size must be equal or more than frame number of
the same PW.
388
PW CONFIGURATION IS NOT UPDATED TO ETIP
PLUG-IN UNIT
The PW configuration is not updated to the ETIP plug-in
unit due to that the unit or connection to it is not working.
389
PW CONFIGURATION SAVED ON OMU FILE, BUT NOT
IN ETIP UNIT
The PW configuration is saved on the OMU file, but not in
the ETIP unit due to that the unit or LAPD connection to it
is not working. The PW configuration is uploaded to the
unit automatically after the ETIP unit is working.
390
NSVCS UNDER ONE NSE MUST HAVE SAME PORT
NUMBER
Every NSVC created under one NSE shall have the same
local UDP port.
391
IBTS SHARING CAN BE ENABLED ONLY WHEN THE
VALUE OF NEIGHBOURINGRNWELEMENT IS ADA
IBTS Sharing can be enabled only when the value of
NeighbouringRNWElement is ADA.
392
IBTS SHARING CAN BE SUPPORTED ONLY WHEN
CELL DCH RELOCATION IS SUPPORTED
IBTS Sharing can be supported only when cell DCH
relocation is supported.
Issue: 30-0
DN987378
43
Error messages
General Error Messages of System
393
IPBASEDROUTEIDIUR MUST BE DEFINED IF
NEIGHBOURINGRNWELEMENT IS FLEXI DIRECT RNC
ipbasedrouteidiur must be defined if
neighbouringrnwelement is Flexi Direct RNC
394
ONLY ONE PLMN ID SHOULD BE CONFIGURED FOR
THOSE IURS WHICH SUPPORT IBTSSHARING
Only one PLMN ID should be configured for those IURs
which support IBTSSharing.
395
PLMNID OF IURS WHICH SUPPORT IBTS SHARING
MUST BE THE SAME
PLMNId of IURs which support IBTS Sharing must be the
same.
396
THE MAX NUMBER OF IUR OBJECTS NEIGHBORING
RNC IS 32
The number of IUR objects neighboring RNC exceeded
the limit.
397
THE RELATION BETWEEN SRNC AND FLEXI DIRECT
RNC CANNOT BE DEFINED BOTH IN
CONTROLLERIDPAIR AND IUR
the relation between srnc and Flexi Direct RNC cannot be
defined both in controlleridpair and iur
398
ONE ADA CAN BE USED BY ONLY ONE RNC FOR IBTS
SHARING
One ADA can be used by only one RNC for IBTS Sharing.
399
MAXBITRATEDLPSNRT SHOULD BE BIGGER THAN OR
EQUAL TO INITIALBITRATEDL
MaxBitRateDLPSNRT should be bigger than or equal to
InitialBitRateDL.
400
INITIALBITRATEDL SHOULD BE BIGGER THAN OR
EQUAL TO MINALLOWEDBITRATEDL
The value of InitialBitRateDL should be bigger than or
equal to the value of MinAllowedBitRateDL.
401
MAXBITRATEULPSNRT SHOULD BE BIGGER THAN OR
EQUAL TO INITIALBITRATEUL
MaxBitRateULPSNRT should be bigger than or equal to
InitialBitRateUL.
402
44
INITIALBITRATEUL SHOULD BE BIGGER THAN OR
EQUAL TO MINALLOWEDBITRATEUL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The value of InitialBitRateUL should be bigger than or
equal to the value of MinAllowedBitRateUL.
403
FMC IS STILL BEING USED BY THE VCEL
FMC is still being used by the VCEL.
404
HOP IS STILL BEING USED BY THE VCEL
HOP is still being used by the VCEL.
405
WRAB IS STILL USED BY THE VCEL
WRAB is still used by the VCEL.
406
NO ANSWER RECEIVED FROM RRA CMA IN TIME
Timer for waiting an answer from rra cma has expired, and
no answer has been received.
407
INVALID EPD VALUE
EPD value is invalid.
408
EACH WCDMA CELL CAN HAVE ONLY ONE GANSPECIFIC INTER-RAT NEIGHBOR CELL (ADJG)
Each WCDMA cell can have only one GAN-specific interRAT neighbor cell (ADJG).
409
IBTSRNCMAPPING CAN ONLY BE SET TO NOT USED
IF NEIGHBOURINGRNWELEMENT IS 1 (3G-WCDMA
RNC)
When NeighboringRNWElement is 1 (3G-WCDMA RNC),
IBTSRNCMapping can only be set to not used.
410
INVALID IBTS SHARING CONFIGURATION
IBTSSharingRncId or one IUR whose IBTSRNCMapping
must be defined. RelocationSupport of more than one IU
CS and IU PS is supported when the value of
CSVoiceServiceSupport is IBTS Sharing.
411
UNIT POOL DATABASE ALREADY CONTAINS A POOL
WITH THE GIVEN POOL ID
Unit pool database already contains a pool with the given
pool ID.
412
THE REQUESTED POOL DOES NOT EXIST IN THE
UNIT POOL DATABASE
The requested pool does not exist in the unit pool
database.
Issue: 30-0
DN987378
45
Error messages
General Error Messages of System
413
THE GIVEN UNIT IS ALREADY ASSIGNED TO THE
POOL
The given unit is already assigned to the pool.
414
THE REQUESTED UNIT IS NOT ASSIGNED TO THE
POOL
The requested unit is not assigned to the pool.
416
THE MAX COUNT OF IUR WHOSE
NEIGHBOURINGRNWELEMENT IS 1 SHOULD NOT
EXCEED 1
The max count of IUR whose NeighbouringRNWElement
is 1 (3G WCDMA RNC) should not exceed 1.
417
CALLER OF LIBGEN FUNCTION UNAUTHORIZED
The prioritized functions of LIBGEN are called by an
unauthorized process.
418
PARAMETERS OF LIBGEN FUNCTION ERRONEOUS
The parameters to be transmitted to the LIBGEN function
are incorrect.
419
RESOURCES RESERVED BY LIBGEN FUNCTION
INSUFFICIENT
The resources to be reserved in the LIBGEN function are
insufficient.
420
USE OF LIBGEN FUNCTION ERRONEOUS
The LIBGEN function is called incorrectly.
421
MESSAGE USED BY LIBGEN FUNCTION INVALID
The message to be transmitted to the LIBGEN function is
incorrect.
422
HAND USED BY LIBGEN FUNCTION IS FREE INSTEAD
OF BEING RESERVED
The hand to be transmitted as a parameter to the LIBGEN
function is no longer reserved although the function is for
reserved hands.
423
NO REAL HAND RESERVATION TIME-OUTS
The LIBGEN function HAND_RESERVATION_TIMEOUT
returns this error code when the routine is called
unnecessarily (=time limit of hand reservation has not
expired).
46
DN987378
Issue: 30-0
General Error Messages of System
424
Error messages
TIME-OUT IN ENTERING MESSAGE REMOTE
PROCEDURE CALL
An error code returned by the call of the
MSG_RPC_THROUGH_WINDOW routine when the
service is not received at all within the defined period.
425
TIME-OUT IN RECEIVING ANSWER MESSAGE TO
REMOTE PROCEDURE CALL
An error code returned by the
MSG_RPC_THROUGH_WINDOW routine when in the
routine, no answer message is received after the message
transmission within the defined time limit.
426
GIVEN WINDOW NOT FOUND IN
MSG_RPC_THROUGH_WINDOW-ROUTINE
The flow control window given as a parameter to the
MSG_RPC_THROUGH_WINDOW routine is not found.
427
SERVICE NOT SUPPORTED
The service is not supported in this network element.
428
UNIT POOL WAS DELETED BECAUSE THERE ARE NO
UNITS CONNECTED TO THIS POOL
Unit pool was deleted because there are no units
connected to this pool.
429
FAILED TO GET RUNNING BUILD ID WITH BOSLIB
Failed to get running build ID. The BOSLIB library has
returned error.
430
FAILED TO GET BUILD INFO FROM SOMAFI WITH
SWFLIB
Failed to get build info from SOMAFI. The SWFLIB library
has returned error.
431
THE DEFAULT BUILD IN SOMAFI IS INVALID (NOT
FOUND OR CORRUPTED)
The default build in SOMAFI could not be found correctly.
The reason could be that SOMAFI is corrupted or patched
wrongly etc.
432
FAILED TO SET DEFAULT BUILD IN SOMAFI
Failure when setting the default build in SOMAFI. The
service has returned the error.
433
Issue: 30-0
CHANGING OF THE SW BUILD HAS FAILED
DN987378
47
Error messages
General Error Messages of System
The changing of the SW build has failed. System is not
running with the requested SW build.
434
ILLEGAL MAC ADDRESS
The MAC address is illegal.
435
NE3S LOAD MODULE ERROR
Load module does not exist, or an error has occurred while
loading load module from disk.
436
LETGR UPDATE FAILURE
The update of a configuration change to the LETGR unit
has failed. Files in the other units have been updated.
437
NPU UPDATE IS FAILED
The update of a configuration change to the NPU unit has
failed. Files in the other units have been updated.
438
MOCN CANNOT BE ACTIVATED BECAUSE THE MOCN
LICENSE STATE IS CONFIG/OFF INSTEAD OF ON
MOCN cannot be activated, because the MOCN license
state is CONFIG/OFF instead of ON.
439
COMMON PLMN ID IS NOT ALLOWED TO BE
MODIFIED IF RELATION TO WCEL OBJECT EXISTS
Common PLMN ID is not allowed to be modified if relation
to WCEL object exists.
440
SUM OF OPERATORWEIGHT UNDER IUO OBJECTS
MUST BE 0 OR 100
Sum of OperatorWeight under IUO Objects must be 0 or
100.
441
NULLNRIFORCSPOOL OF IUOPERATOR MUST BE
UNIQUE WITH OTHERS WHEN FLEX IU OR MOCN IS
ACTIVATED
NullNRIForCSPool of IuOperator must be unique with
others, when Flex IU or MOCN is activated.
442
NULLNRIFORPSPOOL OF IUOPERATOR MUST BE
UNIQUE WITH OTHERS WHEN FLEX IU OR MOCN IS
ACTIVATED
NullNRIForPSPool of IuOperator must be unique with
others, when Flex IU or MOCN is activated.
443
48
NRILENGTHFORCSCN OF ALL IUOPERATOR MUST BE
SAME WHEN FLEX IU OR MOCN IS ACTIVATED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
NRILengthForCSCN of all IuOperator must be same, when
Flex IU or MOCN is activated.
444
NRILENGTHFORPSCN OF ALL IUOPERATOR MUST BE
SAME WHEN FLEX IU OR MOCN IS ACTIVATED
NRILengthForPSCN of all IuOperator must be same, when
Flex IU or MOCN is activated.
445
IP ADDRESS IS ALREADY IN USE
IP ADDRESS IS ALREADY IN USE
446
PRIMARY UNIT ALREADY EXISTS IN THE POOL
Primary unit already exists in the pool.
447
SECONDARY UNIT ALREADY EXISTS IN THE POOL
Secondary unit already exists in the pool.
448
UNIT IS ALREADY ASSIGNED TO THE OTHER POOL
Unit is already assigned to the other pool.
449
ILLEGAL MODIFICATION OF PRIMARY OR
SECONDARY UNIT
Illegal modification of primary or secondary unit.
450
UNIT DELETION IS DENIED DUE TO OTHER ONGOING
DELETION
Unit deletion is denied due to other ongoing deletion.
451
SECONDARY UNIT HAS BEEN DELETED FROM THE
POOL
Secondary unit has been deleted from the pool.
452
PRIMARY UNIT HAS BEEN DELETED FROM THE POOL
The primary unit has been deleted from the pool.
453
ORDINARY UNIT HAS BEEN DELETED FROM THE
POOL
Ordinary unit has been deleted from the pool.
454
PRIMARY UNIT OF THE POOL HAS BEEN MODIFIED
The primary unit of the pool has been modified.
455
SECONDARY UNIT OF THE POOL HAS BEEN
MODIFIED
Secondary unit of the pool has been modified.
Issue: 30-0
DN987378
49
Error messages
General Error Messages of System
456
CONFIGURATING MOCN WCEL ONLY IF
MOCNENABLED IS ENABLED; DISABLING
MOCNENABLED ONLY IF NO MOCN WCEL EXISTS
MOCN WCEL can be created or modified only when
MOCNenabled is enabled. MOCNenabled can be disabled
only when no MOCN WCEL exists.
457
VP SERVICE CATEGORY CHANGE IS NOT ALLOWED
IF THERE IS A VC NOT USED BY OWN COCO UNDER
THIS VP
VP service category change is not allowed if there is a VC
not used by own COCO under this VP.
458
NETYPE INDICATED BY BTS DOES NOT MATCH
IUBWORKINGMODE CONFIGURED IN RNC FOR WBTS
OBJECT
NEType reported by BTS does not match with
IubWorkingMode configured by user.
459
PRIMARY DOWNLINK SCRAMBLING CODE AND
FRAME TIMING OFFSET OF A CELL COMBINATION
MUST BE UNIQUE WITHIN WBTS
The primary downlink scrambling code and frame timing
offset of a cell combination must be unique within WBTS.
460
THE VALUE OF DELAYTHRESHOLDMID2MSTTI IS NOT
LESS THAN THE VALUE OF
DELAYTHRESHOLDMAX2MSTTI
The value of Delaythresholdmid2mstti is not less than the
value of delaythresholdmax2mstti.
461
THE VALUE OF DELAYTHRESHOLDMIN2MSTTI IS NOT
LESS THAN THE VALUE OF
DELAYTHRESHOLDMID2MSTTI
The value of Delaythresholdmin2mstti is not less than the
value of Delaythresholdmid2mstti.
462
THE VALUE OF THRESHOLDMAXEDPDCHSR3840kbps
IS NOT GREATER THAN VALUE OF
THRESHOLDMAXEDPDCHSR1920kbps
The value of Thresholdmaxedpdchsr3840Kbps is not
greater than the value of
Thresholdmaxedpdchsr1920Kbps.
463
50
HSUPAENABLED CAN BE ENABLED IF
HSDPAMOBILITY IS ENABLED; HSDPAMOBILITY CAN
BE DISABLED IF NO WCEL USES HSUPA
DN987378
Issue: 30-0
General Error Messages of System
Error messages
HSUPAEnabled can be enabled only when HSDPAMobility
is enabled. HSDPAMobility can be disabled only when no
cell is using HSUPA.
464
PriForSRBsOnHSPA MUST BE BIGGER THAN
PriForConvOnHSPA,PriForStreamARP1,
PriForStreamARP2 AND PriForStreamARP3
Values of PriForSRBsOnHSPA must be bigger than values
given to parameters PriForConvOnHSPA,
PriForStreamARP1, PriForStreamARP2 and
PriForStreamARP3.
465
HSUPA2MSTTIENABLED CAN BE ENABLED ONLY IF
HSUPAENABLED IS ENABLED
HSUPA2MSTTIEnabled can be enabled only if
HSUPAEnabled is enabled.
466
MAXTOTALUPLINKSYMBOLRATE CAN BE SET TO
5760KBPS ONLY IF HSUPA2MSTTIENABLED IS
ENABLED
MaxTotalUplinkSymbolRate can be set to 5760kbps only if
HSUPA2MSTTIEnabled is enabled.
467
FDPCHENABLED CAN BE ENABLED ONLY IF
HSUPAENABLED IS ENABLED
FDPCHEnabled can be enabled only if HSUPAEnabled is
enabled.
468
FDPCHENABLED CAN BE ENABLED ONLY IF QOS
PRIORITIZATION IS USED WITH THE PARAMETER
HSPAQOSENABLED
FDPCHEnabled can be enabled only if QoS prioritization is
used with the parameter HSPAQoSEnabled.
469
THE LICENSE OF HSUPA 5.8MBPS IS NOT ON
The license of HSUPA 5.8Mbps is not on.
470
THE LICENSE OF HSUPA 2MS TTI IS NOT ON
The license of HSUPA 2ms TTI is not on.
471
SHARED HSDPA, HSUPA AND HSPA CANNOT BE PUT
IN BUNDLE
Shared HSDPA, HSUPA and HSPA cannot be put in
bundle.
472
Issue: 30-0
THE MAX AMOUNT OF ATER CHANNELS SUPPORTED
BY TDM INTERFACE UNIT EXCEEDED
DN987378
51
Error messages
General Error Messages of System
The max amount of Ater channels supported by TDM
interface unit exceeded.
473
THE MAX AMOUNT OF 32K ATER CHANNELS
SUPPORTED BY TDM INTERFACE UNIT EXCEEDED
The max amount of 32k Ater channels supported by TDM
interface unit exceeded.
474
GRNP FLAG IS NOT SET FOR GIVEN UNIT
GRNP flag has to be set for given unit before the RNC to
IPoA bindings are allowed.
475
PACKET SWITCHED NETWORK TUNNEL IS NOT IN
DISABLED STATE AS IT SHOULD BE
The Packet Switched Network (PSN) tunnel is not in
disabled state as it should be.
476
HSDPA64QAMALLOWED CANNOT BE ACTIVATED
BECAUSE HSDPA64QAM LICENSE STATE IS
CONFIG/OFF INSTEAD OF ON
HSDPA64QAMallowed cannot be activated, because the
HSDPA64QAM license state is CONFIG/OFF instead of
ON.
477
FRLCENABLED CAN BE ENABLED ONLY WHEN HSDPA
DYNAMIC RESOURCE ALLOCATION IS ENABLED
FRLCEnabled can be enabled only when HSDPA dynamic
resource allocation is enabled. HSDPA dynamic resource
allocation can be disabled only if FRLCEnabled is
disabled.
478
HSDPA64QAMALLOWED CAN BE ENABLED ONLY
WHEN FRLCENABLED IS ENABLED
HSDPA64QAMallowed can be enabled only when
FRLCEnabled is enabled, FRLCEnabled can be disabled
only if all HSDPA64QAMallowed is disabled
479
WCEL-HSDPA64QAMALLOWED CAN BE ENABLED
ONLY WHEN THE HARDWARE OF CDSP-DH IS
PRESENT IN UPGRADE MODE
WCEL-HSDPA64QAMallowed can be enabled only when
the hardware of CDSP-DH is present in upgrade mode.
480
SCTP PORT IS NOT UNIQUE FOR ALL IPNBS
SCTP port is not unique for all IPNBs.
481
52
IF COMMONPLMNID/MULTIPLEPLMNLISTINCLUDED IS
DEFINED, CS CORE NETWORK IDENTITY SHALL NOT
BE DEFINED FOR WCEL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
If CommonPLMNId/MultiplePLMNListIncluded is defined,
CS Core Network Identity shall not be defined for WCEL.
482
IF COMMONPLMNID/MULTIPLEPLMNLISTINCLUDED IS
CONFIGURED,PS CORE NETWORK IDENTITY SHALL
NOT BE DEFINED FOR WCEL
If CommonPLMNId/MultiplePLMNListIncluded is
configured, PS Core Network Identity shall not be defined
for WCEL.
483
MIBPLMNIDINCLUDED CANNOT BE MODIFIED WHEN
MOCNENABLED UNDER RNC IS ENABLED
MIBPLMNIdIncluded cannot be modified, when
MOCNenabled under RNC is enabled.
484
LOAD MODULE TABLE IN NE3SAG IS FULL
Load Module table in NE3SAG is full and every load
module is in use.
485
BONDING INTERFACE EXISTS
Interface configured to bonding slave device. Slave device
delete not allowed before bonding device is deleted.
486
IF CPCENABLED ENABLED, FDPCHENABLED MUST
BE ENABLED; IF FDPCHENABLED DISABLED,
CPCENABLED MUST BE DISABLED
If the parameter CPCEnabled of WCEL is enabled, the
parameter FDPCHEnabled of WCEL must be enabled. If
the parameter FDPCHEnabled of WCEL is disabled, the
parameter CPCEnabled of WCEL must be disabled.
487
ALIAS SUBSCRIBER
The profile type of the radio subscriber is an alias.
488
MAXIMUM PW AMOUNT EXCEEDED
New PW (Pseudo Wire) is tried to create but there is no
room for it.
489
MAXIMUM PSN TUNNEL AMOUNT EXCEEDED
New PSN (Packet Switched Network) tunnel is tried to
create but there is no room for it.
490
GROUP DEFINED
The group is already a local group.
491
GROUP ALREADY DEFINED
The group is already a member group of CoG.
Issue: 30-0
DN987378
53
Error messages
General Error Messages of System
492
GROUP HAS BEEN DEFINED
The group is already a dedicated group.
493
INVALID GROUP MODE FOR DEDICATED DATA GROUP
The group mode must be normal for a dedicated data
group.
494
GROUP DEFINITION USED
The group is already a dedicated group, cannot be a cover
group.
495
GROUP DEFINITION HAS BEEN USED
The group is already a dedicated group.
496
IF IULINKSTATUS IS ENABLED, IU OBJECT CANNOT
BE DELETED
If IuLinkStatus is enabled, IU object cannot be deleted.
497
THE LAST IU OBJECT CANNOT BE DELETED, IF
THERE IS ANY WCEL OBJECTS THAT EXISTS
The last IU object cannot be deleted, if there is any WCEL
objects that exists.
498
PROPOSED BIT RATE IS NOT VALID FOR A
MULTIPLEXED D-CHANNEL
Within a multiplexed d-channel, d-channels with the same
PCM and TSL, all d-channels must have the same bit rate.
499
TEI VALUE IS NOT ALLOWED FOR THE SAPI
The given value of TEI is not valid for the type of the dchannel or for the given SAPI.
500
SAPI VALUE IS NOT VALID
The given value of SAPI is not valid for the type of the dchannel.
501
MULTIPLEXED D-CHANNEL NOT COMPATIBLE WITH
EXISTING ONE
Within a multiplexed d-channel with the same PCM and
TSL, all d-channels must be of type multiplexed.
502
SIGNALING UNIT NOT COMPATIBLE WITHIN
MULTIPLEXED D-CHANNEL
Within a multiplexed d-channel, d-channels with the same
PCM and TSL, the same logical signaling computer unit
must be used.
54
DN987378
Issue: 30-0
General Error Messages of System
503
Error messages
BITRATE NOT COMPATIBLE WITHIN MULTIPLEXED DCHANNEL
Within a multiplexed d-channel with the same PCM and
TSL, each d-channel must have the same bit rate.
504
SAPI-TEI COMBINATION NOT UNIQUE WITHIN
MULTIPLEXED D-CHANNEL
Within multiplexed d-channels, the d-channels with the
same PCM and TSL, each SAPI - TEI combination must
be unique.
505
TOO MANY D-CHANNELS WITHIN A MULTIPLEXED DCHANNEL
There can be at most 16 D-Channels which are
multiplexed, using the same PCM and TSL.
506
WBTS-BROADCASTSIB15 CANNOT BE USED WHEN
RNC-LCSFUNCTIONALITY IS NOT ENABLED
WBTS-BroadcastSIB15 cannot be enabled when RNCLCSFunctionality is not enabled.
507
WBTS-BROADCASTSIB15 CANNOT BE ENABLED
WHEN WSMLC-LCSINTERFACEOPTION IS NOT IUPC
WBTS-BroadcastSIB15 cannot be enabled when WSMLCLCSInterfaceOption is not IUPC.
508
WBTS-BROADCASTSIB15.2 OR WBTSBROADCASTSIB15.3 CONFLICTED WITH WBTSBROADCASTSIB15
WBTS-BroadcastSIB15.2 and WBTS-BroadcastSIB15.3
can be enabled only when WBTS-BroadcastSIB15 is
enabled.
509
AGPS BROADCAST DATA COLLECTION RELEATED
BDTPRB MESSAGE WAITING TIMEOUT IN L3 RRAPRB
AGPS broadcast data collection related BDTPRB message
waiting time out in L3 RRAPRB.
510
PROTECTION GROUP CONNECTED TO THE LETGR
EXIST
Deleting the protection group is not allowed because the
LETGR connected to the protection group exists.
511
PROTECTION GROUP RELATED TO THE LETGR DOES
NOT EXIST
Creation of the LETGR is not allowed because the
protection group related to the LETGR does not exist.
Issue: 30-0
DN987378
55
Error messages
General Error Messages of System
512
ILLEGAL PASSWORD
The password is given incorrectly from the terminal.
513
ERROR IN READING PASSWORD FILE
Reading of the password file from disk has failed.
514
NO AUTHORITIES FOR SESSION
The process starting the session has no authorities. The
authority data has not been found.
515
ILLEGAL TERMINAL STATE
The terminal starting a session is not in a state in which it
is allowed to start a session.
516
ILLEGAL DIALOG STATE
The starting of a session has failed because it is not
possible to start several sessions on the terminal, or the
terminal is in state BLOCKED.
517
MML CHECKSUM ERROR
The check sum of the MML program has changed. Copy
the MML program from back-up copy to disk.
518
NO SUCH LANGUAGE
The change of language has failed. The defined language
is not available.
519
MML MACRO NAME MISSING
There is no MML macro name after the @ sign starting the
execution of the MML macro.
520
ILLEGAL MARK IN MML MACRO START LINE
There is an illegal mark in the start line of a MML macro.
521
MML MACRO NAME IS TOO LONG
The MML macro name is too long.
522
MISSING END MARK IN MML MACRO START LINE
The end mark is missing at the end of the start line of a
MML macro.
523
ILLEGAL MML MACRO NAME
The name of the MML macro in the command line differs
from the one defined in the MML macro.
524
56
TOO MANY SUB-MML-MACRO CALLS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The maximum number of nested sub-MML-macros has
been exceeded.
525
ILLEGAL MML MACRO DATA AREA HANDLE
The allocation of the data area of an MML macro has
failed.
526
MML MACRO PARAMETER SYNTAX DEFINITION
ERROR
A syntax error in the parameter definition of an MML
macro.
527
ILLEGAL MML MACRO CALL PARAMETER
The string that has been given as a parameter is illegal.
Check the string and the definition of the parameter of the
MML macro.
528
MML MACRO LOADING ERROR
The loading of an MML macro from the disk to the data
area failed.
529
MML OUTPUT BUFFER HANDLING ERROR
Handling error of the execution output buffer of the MML
program.
530
MISSING SEMICOLON IN DEFINITION PART
The semicolon is missing at the definition part of the MML
macro.
531
DEFINITION ERROR IN MML MACRO
There is an incorrect definition in the MML macro.
532
TOO MANY VARIABLE DEFINITIONS
The maximum number of variable definitions has been
exceeded.
533
COMMAND EXECUTION ABORTED
A Non-MML-program announcement of the command
execution abortion.
534
COMMAND EXECUTION FAILED
A Non-MML-program announcement of the command
execution failure.
535
COMMAND IGNORED
A Non-MML-program announcement of the command
having been ignored.
Issue: 30-0
DN987378
57
Error messages
General Error Messages of System
536
COMMAND ORDERED
A Non-MML-program announcement of the command
having been ordered.
537
COMMAND BLOCKED
A Non-MML-program announcement of the command
execution abortion due to blocking.
538
DYNAMIC CONFIGURATION OF INTERFACE UNIT IS
NOT ALLOWED CURRENTLY
The dynamic configuration in interface unit is not currently
allowed. Configuring of interface unit is not allowed when
parent unit is in starting state. In such case, wait a little
while so that parent unit is up and running normally and
then retry the configuration operation. Also when
configuring several objects in a row, the update in interface
unit may take a little while, so a little delay may be needed
in-between sequential operations.
539
NULL NRI VALUE FOR CS POOL CANNOT BE GIVEN
TO ANY MSC OF THE POOL
Null NRI value for CS Pool cannot be given to any MSC of
the pool.
540
NULL NRI VALUE FOR PS POOL CANNOT BE GIVEN
TO ANY SGSN OF THE POOL
Null NRI value for PS Pool cannot be given to any SGSN
of the pool.
541
IF NRT DCH TRAFFIC IS CONFIGURED OVER IP, ALL
OTHER NRT TRAFFICS SHOULD BE CONFIGURED
OVER IP
For parameter IubTransportMedia, if NRT DCH traffic is
configured over IP, all other NRT traffics should be
configured over IP.
542
CARTRIDGE DOES NOT EXIST
Cartridge does not exist.
543
SYSTEM PRELOADING IS ALREADY ONGOING
System preloading is already ongoing.
544
COMMAND NOT AUTHORIZED
Command execution not authorized.
545
TRANSMISSION ERROR
Data transmission to the I/O-device failed.
58
DN987378
Issue: 30-0
General Error Messages of System
546
Error messages
PWSMCELLGROUP,PWSMSHUTDOWNORDER,PWSMS
HUTDOWNREMCELL,POWERSAVEHSPATYPE
CANNOT BE MODIFIED IF PWSMINUSE IS ON
WCEL-PWSMCellGroup, WCEL-PWSMShutdownOrder,
WCEL-PWSMShutdownRemCell and WCELPowersaveHSPAType cannot be modified if WBTSPWSMInUse is ON.
547
CM SENDS INVALID MODE PARAMETER TO TAC
CM sends invalid mode parameter to TAC in
unified_session_setup_s.
548
CM SENDS INVALID SUBMOD PARAMETER TO TAC
CM sends invalid submod parameter to TAC in
unified_session_setup_s.
549
CM SENDS INVALID UNIT TYPE PARAMETER TO TAC
CM sends invalid unit type parameter to TAC in
unified_session_setup_s.
550
CM SENDS INVALID UNIT INDEX PARAMETER TO TAC
CM sends invalid unit index parameter to TAC in
unified_session_setup_s.
551
CM SENDS INVALID RESOURCE ENCODE
PARAMETER TO TAC
CM sends invalid resource encode parameter to TAC in
unified_session_setup_s.
552
NO FREE RESOURCES IN TRM TABLE TO SET UP A
CONNECTION
There are no free resources in TRM table to set up a
connection.
553
CM SENDS INVALID CONN_ID PARAMETER TO TAC
When mode is in delete_c or modify_c, CM sends invalid
conn_id in TRM table to TAC.
554
NO FREE L3 LICENCE AVAILABLE FOR ETHERNET
SWITCH
There is no free L3 license available for Ethernet switch.
555
CHANGING STATE OF L3 LICENSE TO ETHERNET
SWITCH IS FAILED
Changing state of L3 license to Ethernet switch is failed.
Issue: 30-0
DN987378
59
Error messages
General Error Messages of System
556
ETHERNET SWITCH HW OR SW IS NOT CAPABLE TO
L3 MODE
Ethernet switch HW or SW is not capable to L3 mode.
557
DELETING FUNCTIONAL UNIT IS FAILED BECAUSE IT
HAS A VIRTUAL GROUP AS A CHILD UNIT
The functional unit cannot be deleted when it has a virtual
group as a child unit and no pair unit to attach
automatically. For example, IWST cannot be deleted when
it has LETGR as a child, but IWSEP-0 can be deleted
when it has IWSEP-1 as spare unit.
558
RRB-TMA DOES NOT ACKNOWLEDGE C-RNTI
ALLOCATION AFTER PRB RESTART
RRB-tma does not acknowledge C-RNTI allocation
temporarily after PRB restart.
559
NB/RSXXX BTS DOES NOT SUPPORT STREAMING
QOS AND CS VOICE OVER HSPA FOR HSPA FEATURE
NB/RSxxx BTS does not support Streaming QoS and CS
Voice over HSPA for HSPA feature.
560
CONTROL PLANE DESTINATION IP ADDRESS
CONFIGURED IN IPNB HAS ALREADY BEEN USED
Control plane destination IP address configured in IPNB
has already been used.
561
PRIFORCONVONHSPA MUST TAKE VALUES BIGGER
THAN PRIFORSTREAMARP1, PRIFORSTREAMARP2
AND PRIFORSTREAMARP3
PriForConvOnHSPA must take values bigger than
PriForStreamARP1, PriForStreamARP2 and
PriForStreamARP3.
562
PTXTARGETTOTMIN CANNOT TAKE VALUES THAT
ARE LESS THAN THE VALUE OF PTXTARGET
PtxTargetTotMin cannot take values that are less than the
value of PtxTarget.
563
PTXTARGETTOTMIN CANNOT TAKE VALUES THAT
ARE GREATER THAN THE VALUE OF
PTXTARGETTOTMAX
PtxTargetTotMin cannot take values that are greater than
the value of PtxTargetTotMax.
564
60
PTXTARGETTOTMAX CANNOT TAKE VALUES THAT
ARE GREATER THAN THE VALUE OF PTXCELLMAX
DN987378
Issue: 30-0
General Error Messages of System
Error messages
PtxTargetTotMax cannot take values that are greater than
the value of PtxCellMax.
565
PRXTARGETMAX CANNOT TAKE VALUES THAT ARE
SMALLER THAN THE VALUE OF PRXTARGET
PrxTargetMax cannot take values that are smaller than the
value of PrxTarget.
566
HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR
STR_CS_C ONLY WHEN AMRWITHHSDSCH IS SET TO
ENABLED
HSPAQoSEnabled can be set to cs_voice_c or str_cs_c
only when AMRWithHSDSCH is set to enable.
567
HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR
STR_CS_C ONLY WHEN AMRWITHEDCH IS SET TO
ENABLE
HSPAQoSEnabled can be set to cs_voice_c or str_cs_c
only when AMRWithEDCH is set to enable.
568
HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR
STR_CS_C ONLY WHEN HSUPAENABLED IS SET TO
ENABLE
HSPAQoSEnabled can be set to cs_voice_c or str_cs_c
only when HSUPAEnabled is set to enable.
569
HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR
STR_CS_C ONLY WHEN FDPCHENABLED IS SET TO
ENABLE
HSPAQoSEnabled can be set to cs_voice_c or str_cs_c
only when FDPCHEnabled is set to enable.
570
HSPAQOSENABLED CAN BE SET TO CS_VOICE_C OR
STR_CS_C ONLY WHEN CPCENABLED IS SET TO
ENABLE
HSPAQoSEnabled can be set to cs_voice_c or str_cs_c
only when CPCEnabled is set to enable.
571
WCEL-HSPAQOSENABLED CAN BE SET TO
CS_VOICE_C OR STR_CS_C ONLY WHEN CDSP-DH
EXISTS IN UPGRADE MODE
WCEL-HSPAQoSEnabled can be set to cs_voice_c or
str_cs_c only when CDSP-DH exists in upgrade mode.
572
CID USAGE EXCEEDS THE THRESHOLD
Current CID usage for ATM resources exceeds the CID
threshold specified in the WBTS object.
573
Issue: 30-0
CAC USAGE EXCEEDS THE THRESHOLD
DN987378
61
Error messages
General Error Messages of System
Current CAC usage for ATM/IP resources exceeds the
CAC threshold specified in the WBTS object.
574
AAL2 PATH TYPE AND USAGE CONFIGURATION IS
ILLEGAL IF A2SU IS USED AND DYN NRT DCH
SCHEDULING WITH PATH IS ON
AAL2 path type and usage configuration is illegal if A2SU
is used and Dyn NRT DCH Scheduling With Path is on.
575
NOT MORE THAN ONE DNBAPTP CAN BE DEFINED IF
COCO-GENERATEAAL2NUM IS 3 (ONE A2EA FOR BTS)
Not more than one DNBAPTP can be defined if COCOGenerateAAL2Num is 3 (One A2EA for BTS).
576
ABIS DELAY MEASUREMENT CHANNEL IS NOT
CONFIGURED TO BSC
Measurement channel is not found from BSC.
577
BTS SW VERSION DOES NOT SUPPORT ABIS DELAY
MEASUREMENT
Error code used in BSC when the BTS does not support
Abis delay measurement.
578
MAXIMUM NUMBER OF ABIS DELAY MEASUREMENT
CHANNELS IS REACHED
There is no room for new measurement channels in
AD4FIL.
579
THE STATE OF LICENSE FEATURE CS VOICE OVER
HSPA IS NOT ON
The state of license feature CS Voice Over HSPA is not
ON.
580
PRELOADING IS NOT ONGOING
Preloading is not ongoing.
581
SYSTEM PRELOADING IS CANCELED NOW
System preloading is canceled now.
582
SYSTEM PRELOADING IS ALREADY CANCELED
System preloading is canceled already.
583
SYSTEM PRELOADING IS BEING CANCELED AND
CANNOT DO PRELOADING NOW
System preloading is being cancelled.
584
62
TAC SENDS INVALID CONN_ID PARAMETER TO TAE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
When mode is in delete_c or modify_c, TAC sends invalid
conn_id to TAE.
585
ILLEGAL ENDPOINT FALLBACK CONFIGURATION
Illegal endpoint fallback parameter configuration on route
586
NOT MORE THAN TWO AAL2TP CAN BE DEFINED PER
WAMID FOR ULTRASITE BTS IF COCO AAL2MULTIPLEXING IS DISABLED
Not more than two AAL2TP can be defined per WAMId for
Ultrasite BTS if COCO - AAL2Multiplexing is 0
(Multiplexing disabled).
587
PRELOADER HAS BEEN CANCELLED
Used in PLBAMA, to tell that the pre-loading has been
cancelled.
588
PRELOAD NOT STARTED, CANCEL MSG SHOULD NOT
BE RECEIVED
Pre-load is not started in PLBAMA or DAQTOR, but a
cancel msg is received.
589
WCEL-NBROFSCCPCHS CANNOT BE ONE IF WCELPCH24KBPSENABLE IS ENABLED.
WCEL-NbrofSCCPCHs cannot be one if WCELPCH24kbpsEnable is enabled.
590
24KBPS PAGING CHANNEL LICENSE STATE IS NOT
ON
24kbps Paging Channel License state must be ON for cell
unlock if PCH24kbpsEnabled is enabled and
NbrofSCCPCHs is greater than 1.
591
ANOTHER O&M OPERATION IS ALREADY ONGOING IN
BTS
Another O&M operation is already ongoing in BTS.
592
USE OF MULTIPLEXED D-CHANNELS NOT POSSIBLE
IN THIS BCF
The site type of BCF does not allow the use of multiplexed
D-channels. A multiplexed D-channel contains one O&Msignaling and several telecom-signaling in the same
physical timeslot (PCM-TSL). Up to 16 simultaneous
logical LAPD connections can be multiplexed into one
timeslot.
593
Issue: 30-0
DEFINED BTS SITE SUBTYPE IS NOT SUITABLE FOR
BTS SOFTWARE
DN987378
63
Error messages
General Error Messages of System
The defined BTS site subtype is not suitable for BTS
software.
594
COMMAND NOT POSSIBLE AS UNIT HAS IP
CONFIGURATION
The command is not possible because the IP configuration
already exists.
595
VALUES 45 TO 51 ARE NOT ALLOWED FOR SUPER
EXTENDED RADIUS PARAMETER
Operator shall not be allowed to use values 45 to 51 for
Super Extended Radius parameter in FlexiEDGE BTS.
596
UNIT OTO RESTART MODE FAILS
Unit oto restart mode fails.
597
AUTO CLOSE EXECUTED
The tape has filled up. The TAPEDR program block closes
the file, rewinds the tape and sets the tape drive into state
OFF LINE.
598
LOGICAL END
The logical end of the tape (two successive tape
characters) has been found during the command
execution.
599
FILE LABEL NOT COMPLETE
An incorrect label structure has been found during the
command execution.
600
LAST FILE NOT CLOSED
The last file on the tape has not been closed.
601
TAPE FILE ALREADY EXISTS
An attempt has been made to open a file on tape, with the
multifile open command, with a name that is in use already.
602
NAME MISMATCH WITH LAST FILE
A file name has been given in the file reopen command,
that does not match with the name in the end label of the
last file on tape.
603
REOPEN NOT ALLOWED
The reopen command is directed to a tape drive that does
not contain DX tape.
604
64
ILLEGAL TAPE TYPE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
An attempt has been made to set an illegal tape type with
the tape type set command.
605
TAPE PREFORMATTED
An attempt has been made to search for a file on a
preformatted tape, or to open the first file on tape with the
multifile open command.
606
TAPE WRITE PROTECTED
A writing has been directed to a tape unit with a write
protected reel. There is no plastics write protection ring in
the reel.
607
NO PID STRING
An attempt has been made to write with the MAS service
terminal extension a file from memory to disk the
identification character string of which does not match with
the file name.
608
NO RESPONSE FROM TAPEDR
The TAPEDR program block does not answer to the sent
message.
609
NO RESPONSE FROM EDISKD
The EDISKD program block does not answer to the sent
message.
610
SL TPI SHOULD BE BLANK FOR MTP3
SL TPI should be blank for MTP3.
611
WCEL-HSPA72USERSPERCELL CAN BE ENABLED
ONLY WHEN WCEL-HSUPAENABLED IS ENABLED
WCEL-HSPA72UsersPerCell can be enabled only when
WCEL-HSUPAENABLED is enabled. WCELHSUPAENABLED cannot be disabled if WCELHSPA72UsersPerCell is enabled.
612
LICENSE STATE OF HSPA72USERSPERCELL MUST BE
ON FOR CELL UNLOCKING WHEN
HSPA72USERSPERCELL IS ENABLED
License state of HSPA72UsersPerCell must be ON for cell
unlocking when WCEL-HSPA72UsersPerCell is enabled.
613
MERGED PGMS900 AND EGSM900 FEATURE IS NOT
IN USE IN BSC
Parameter Merged PGSM and EGSM cannot be enabled
due to that there is no license installed in BSC or license
has been expired or license is in wrong state.
Issue: 30-0
DN987378
65
Error messages
General Error Messages of System
614
UNLOCKED BTS EXISTS IN THE SEGMENT
All BTS should be enabled when modifying parameter
Merged PGSM and EGSM.
615
IP LINK IS NOT AVAILABLE
BFD monitoring reports that the IP link is not available.
616
COCOID OR ATMIF/VPI/VCI TRIPLET AND IPNBID
CANNOT BE BOTH DEFINED
COCOId or ATMIf/VPI/VCI triplet and IPNBId cannot be
both defined.
617
COCO DEFINED IUBTRANSPORTMEDIA MAY NOT
CONTAIN IPIUB OR IPNB DEFINED
IUBTRANSPORTMEDIA MAY ONLY CONTAIN IPIUB.
When COCOId or ATMIf/VPI/VCI triplet,
IubTransportMedia may not contain the value IPIub .When
IPNBId is defined IubTransportMedia may only contain the
value IPIub.
618
COPY BU SW BUILD AS CD INSTALLATION BASE
FAILED
Copy BU SW build as CD installation base failed.
619
DATA CONVERSION DURING SW UPGRADE FAILED
Data conversion during SW upgrade failed.
620
SCRIPT FILE CONTAINS UNKNOWN COMMANDS
The script file contains unknown commands.
621
NE DOES NOT ALLOW SW UPGRADE
The NE does not allow SW upgrade.
622
FLASH UPDATE FAILED DURING THE SW BUILD
UPGRADE
Flash update failed during the SW build upgrade.
623
HMS SW UPDATE FAILED DURING THE SW BUILD
UPGRADE
HMS SW update failed during the SW build upgrade.
624
NE DOES NOT ALLOW SW BUILD AUTO RETURN
NE does not allow SW build auto return.
625
NE DOES NOT ALLOW SYSTEM RESTART
NE does not allow system restart.
66
DN987378
Issue: 30-0
General Error Messages of System
626
Error messages
CUSTOMER FILE COPYING FAILED
Customer file copying failed.
627
CHANGING DEFAULT BUILD FAILED
Changing default build failed.
628
INCORRECT UNIT STATUS
Incorrect unit status is detected.
629
CREATING TRIAL HAS FAILED
Creating trial has failed.
630
TRIAL CUTOVER HAS FAILED
Trial cutover has failed.
631
TRIAL COMPLETION HAS FAILED
Trial completion has failed.
632
FLEXI BTS AUTOCONNECTION FEATURE IS NOT IN
USE IN BSC
Flexi BTS Autoconnection feature is not enabled in BSC.
633
SCF DATA OPERATION IS ONGOING
Uploading, downloading or activation of SCF data is
ongoing.
634
BCF IS NOT CONFLICTING
This BCF is not among the BCFs that have been attached
to the conflicting OMUSIGs.
635
ACTIVATED SCF DATA DOES NOT EXIST
Activated SCF data for the BCF does not exist and data is
now requested from NetAct.
636
SCF DATA UPLOAD IS NOT ONGOING
SCF data upload to NetAct is not ongoing.
637
SCF DATA ACTIVATION IS NOT ONGOING
SCF data activation for commissioned BTSs is not
ongoing.
638
BTS SOFTWARE DOES NOT SUPPORT FLEXI BTS
AUTOCONNECTION FEATURE
BTS software does not support Flexi BTS Autoconnection
feature.
Issue: 30-0
DN987378
67
Error messages
General Error Messages of System
639
SCF DATA FOR BCF DOES NOT EXIST
SCF data for BCF does not exist.
640
INCORRECT SCF PLAN ID FOR THE BCF
Plan ID differs from the existing SCF data plan ID for the
BCF.
641
WRONG BTS COMMISSIONING STATE
BTS Commissioning State is wrong for the action in
question.
642
BTS OAM LINK IS LOCKED
Operation is not possible due to the locked BTS O&M link.
643
SCF DOWNLOAD TO BTS IS ALREADY ONGOING
New SCF cannot be downloaded to BSC because SCF
downloading to BTS is ongoing.
644
INTERFACE MODE IN IWPARA IS NOT COMPATIBLE
WITH NEW INTERFACE UNIT
ET interface parameters cannot be reused for new
interface unit, because interface mode (E1, T1, JT1) in
IWPARA is not compatible.
645
MAX CONFERENCE SUBSCRIBER EXCEEDED
The maximum count of the subscriber is exceeded in the
conference service.
646
LTE SYSTEM INFORMATION FEATURE IS NOT IN USE
IN BSC
LTE System information feature is not enabled in BSC.
Either feature license is not valid or feature status is in
disabled state.
647
MAXIMUM NUMBER OF ADJACENT LTE CELLS FOR
ONE CELL EXCEEDED
There is a maximum number of LTE adjacencies already
created for one cell.
648
CELL ALREADY HAS ADJACENT LTE CELL WITH THE
NEW PLMN_TAC_FREQ VALUE
There is already LTE adjacency created with same PLMN,
TAC, and FREQ combination in the cell.
649
ADJACENT LTE CELL WAS NOT FOUND IN RNW
DATABASE
LTE adjacent cell was not found in RNW database.
68
DN987378
Issue: 30-0
General Error Messages of System
650
Error messages
CELL ALREADY HAS ADJACENT LTE CELL WITH THE
SAME CELL INDEX VALUE
LTE adjacent cell is already created with the given index
value.
651
PARAMETER LTERUT MUST BE HIGHER THAN OR
EQUAL TO PARAMETER LTERLT
Parameter lteAdjCellReselectionUpperThr must be higher
than or equal to parameter lteAdjCellReselectLowerThr.
652
CELL ALREADY HAS ADJACENT LTE CELL WITH THE
SAME EARFCN
There are already LTE adjacent cell defined with same
earfcn value in this segment.
653
LAPD OF THE BCF/TRX IS MULTIPLEXED WITH OTHER
BCF'S LAPD
LAPD of the BCF/TRX is multiplexed with other BCF's
LAPD.
654
TAC USES THIS TO INDICATE THE INVALID IP
ADDRESS
TAC uses this failure code indicating that the IP address in
ip_res_req_s, ip_res_free_req_s is not valid.
655
WBTS- AUTOCONNSITEID SHOULD BE UNIQUE FOR
EVERY BTS
WBTS- AutoConnSiteID should be unique for every BTS.
656
WBTS- AUTOCONNHWID SHOULD BE UNIQUE FOR
EVERY BTS
WBTS- AutoConnHWID should be unique for every BTS.
657
WCEL-URAID MUST BE UNIQUE WITHIN WCELURAIIDLIST
WCEL-URAId must be unique within WCEL-URAIdList.
658
INCONSISTENT DL RX LEVEL THRESHOLDS FOR
BCCH TRX PREFERENCE
Upper-DL-RX-threshold-for-TRX-preference for TCH
(UDRB) cannot be smaller than Lower-DL-RX-thresholdfor-TRX-preference for TCH (LDRB).
659
Issue: 30-0
ENERGY OPTIMISED TCH ALLOCATION IS NOT IN USE
DN987378
69
Error messages
General Error Messages of System
Upper DL RX threshold for TRX prefence for TCH (UDRB)
and Lower DL RX threshold for TRX prefence for TCH
(LDRB) parameters cannot be modified if Energy
Optimised TCH Allocation feature is not in use.
660
VALUE OF HSDPAMAXBITRATEUL CAN BE 16KBPS
ONLY WHEN RNFC-HSDPA16KBPSRETURNCHANNEL
IS ENABLED
The value of HSDPAMaxBitrateUL can be 16kbps only
when RNFC-HSDPA16KBPSReturnChannel is enabled.
661
FLEXI MULTIRADIO FEATURE IS NOT IN USE IN BSC
Flexi Multiradio feature cannot be enabled due to that
there is no licence installed in BSC or licence has been
expired or licence is in OFF/CONF state.
662
FLEXI MULTIRADIO CAPACITY LICENCE EXCEEDED
Capacity of the Flexi Multiradio licence (Flexi Multiradio
TRX HW Activation) exceeded.
663
NE3S LOAD MODULE EXECUTION ERROR
An error has occurred while executing load module.
664
THE GROUP IS ALREADY A COVER GROUP AND
CANNOT BE A DEDICATED GROUP
The group is already a cover group, it can not be a
dedicated group.
665
WLCSE CANNOT BE DELETED FOR A CELL IF ITS
PARENT WBTS HAS WBTS-BROADCASTSIB15 AS
ENABLED
WLCSE cannot be deleted for a cell if its parent WBTS has
WBTS-BroadcastSIB15 as enabled.
666
IU OBJECT CANNOT BE DELETED IF THE IU PRIMARY
OR SECONDARY PLMN IS CONFIGURED IN RNC-CBC
LIST
IU Object cannot be deleted if the IU Primary or Secondary
PLMN is configured in RNC-CBC list.
667
LGMANA TASK QUEUE OVERFLOWED
LGMANA task/message queue overflowed. Leg requests
may have been rejected or discarded.
668
DIRECT ACTIVATION IS DONE, BUT PLANNING
AUTOMATIC UPDATE DOES NOT SUCCEED
Direct activation is done, but planning automatic update
does not succeed.
70
DN987378
Issue: 30-0
General Error Messages of System
669
Error messages
RNW DATABASE IS RESERVED FOR PLAN
DOWNLOADING
RNW database is reserved for plan downloading.
670
RNW DATABASE RESERVED FOR PLAN ACTIVATION
RNW database is reserved for plan activation.
671
RNW DATABASE IS RESERVED FOR PLAN ROLLBACK
The RNW database is reserved for plan rollback.
672
LEG REQUEST TIMED OUT
A leg request could not be serviced within the specified
time limit.
673
RM3 INTERNAL QUEUE FOR INCOMING REQUESTS IS
FULL
RM3 internal queue for incoming requests is full.
674
COCO AAL2 PATH IDS NOT UNIQUE
The AAL2 user plane link related numbering is not unique.
Check the AAL2 path ID values from the COCO object
because there is another COCO object using the same
values.
675
MRDFIL READ ERROR
MRDFIL read error
676
MRDFIL WRITE ERROR
MRDFIL write error
677
MRDFIL FILE IS FULL
MRDFIL file is full
678
MRDFIL FILE NOT SAVED TO DISK
MRDFIL file not saved to disk
679
ATER RESOURCES CONFIGURED TO UNIT
There are Ater resources configured to the unit.
680
COMMAND NOT POSSIBLE AS UNIT HAS PW
CONFIGURATION
The command is not possible because the PW
configuration already exists.
681
Issue: 30-0
WCEL-AMRUNDERTXNC MUST BE SMALLER THAN
WCEL-AMROVERTXNC
DN987378
71
Error messages
General Error Messages of System
WCEL-AMRUnderTxNC should be less than WCELAMROverTxNC.
682
TOTAL EVCS CIR EXCEEDED ETHERNET SHAPING
RATE, CAC FAILED
Total EVCs CIR exceeded ethernet shaping rate, CAC
failed.
683
WRONG NCID TPI
Wrong NCID TPI.
684
PCU HOT RESTART CANNOT BE STARTED RIGHT
NOW
PCU hot restart cannot be started at this time. It is
however possible to try again later.
685
PCU POOLING OPERATION ONGOING
Requested operation cannot be started because some
PCU pooling feature operation is active.
686
PCU NOT IN THE WORKING STATE
PCU is not in the working state, which is needed for the
requested operation.
687
RNHS-THRESHOLDMAXEDPDCHSR3840KBPS MUST
BE GREATER THAN RNHSTHRESHOLDMAXEDPDCHSR960KBPS
RNHS-Thresholdmaxedpdchsr3840Kbps must be greater
than RNHS-Thresholdmaxedpdchsr960Kbps
688
GUEST UNIT NOT PREDEFINED
The guest unit is not pre-defined in the configuration file.
689
WCEL-AMROVERSC MUST BE GREATER THAN WCELAMRUNDERSC
WCEL-AMROVERSC must be greater than WCELAMRUNDERSC.
690
WCEL-AMROVERTRANSMISSION MUST BE GREATER
THAN WCEL-AMRUNDERTRANSMISSION
WCEL-AMROverTransmission must be greater than
WCEL-AMRUnderTransmission.
691
PCU ABIS CONNECTION TYPE NOT SUITABLE
The PCU Abis connection type is not suitable or there is no
PCU with suitable Abis connection type.
72
DN987378
Issue: 30-0
General Error Messages of System
692
Error messages
WCEL-AMROVERTXTOTAL MUST BE GREATER THAN
WCEL-AMRUNDERTXTOTAL
WCEL-AMROverTxTotal must be greater than WCELAMRUnderTxTotal.
693
WCEL-AMROVERTXNONHSPA MUST BE GREATER
THAN WCEL-AMRUNDERTXNONHSPA
WCEL-AMROverTxNonHSPA must be greater than
WCEL-AMRUnderTxNonHSPA.
694
EVC SIR (CIR+EIR) EXCEEDED ETHERNET SHAPING
RATE
EVC SIR (CIR+EIR) exceeded ethernet shaping rate.
695
TPI MISMATCH
Checked TPI values do not match.
696
LETGR CONFIGURATION CHANGE IS NOT ALLOWED
IN THIS STATE
LETGR configuration change is not allowed in this state.
The possible reason is that parent unit is in TE state.
697
ABIS DELAY MEASUREMENT OPTION IS NOT IN USE
IN BSC
Abis Delay Measurement (TDM, PWE3) introduces a new
BSC transmission measurement for measuring the round
trip time of data frames/packets in an Abis interface PCM
in case of TDM transmission or in a PCM of a Pseudo Wire
in case of PWE3 transmission.
698
HSPA REMOVAL FAILED FROM A WCEL DURING CELL
SHUTDOWN/ACTIVATION TRIGGERED BY PWSM
HSPA removal failed from a WCEL during cell
shutdown/activation triggered by PWSM.
699
HSPA CONFIGURATION TO A CELL FAILED DURING
CELL SHUTDOWN/ACTIVATION TRIGGERED BY PWSM
HSPA configuration to a cell failed during cell
shutdown/activation triggered by PWSM.
701
WCEL-PTXCELLMAX MUST BE GREATER THAN OR
EQUAL TO WCEL-PTXMAXHSDPA
WCEL-PTXCELLMAX must be greater than or equal to
WCEL-PTXMAXHSDPA.
702
Issue: 30-0
WBTS-DELAYTHRESHOLDMIN SHOULD BE LESS
THAN WBTS-DELAYTHRESHOLDMID
DN987378
73
Error messages
General Error Messages of System
WBTS-DelayThresholdMin should be less than WBTSDelayThresholdMid.
703
DEPENDENCY AMONG WBTS PARAMETERS
DELAYTHRESHOLDMIN2MSTTI,DELAYTHRESHOLDMI
D2MSTTI AND DELAYTHRESHOLDMAX2MSTTI
DelayThresholdMin2msTTI should be less than
DelayThresholdMid2msTTI, and
DelayThresholdMid2msTTI should be less than
DelayThresholdMax2msTTI.
704
WCEL-HSPAQOSENABLED CAN BE SET TO
CS_VOICE_C OR STR_CS_C ONLY WHEN RNCFRLCENABLED IS SET TO ENABLE
WCEL-HSPAQoSEnabled can be set to cs_voice_c or
str_cs_c only when RNC-FRLCEnabled is set to enable.
705
MAXIMUM NUMBER OF EVC WHICH CAN BE
CONFIGURED TO AN INTERFACE EXCEEDED
The maximum number of EVC which can be configured to
an interface is exceeded.
706
PSE REALLOCATION IS ONGOING
Operation cannot be completed because PCU belongs to a
PSE where BTS/DAP reallocation is ongoing.
707
BASEBAND OR ANTENNA HOPPING CANNOT BE
ENABLED AT THE SAME TIME WITH TX DIVERSITY
TIME SHIFT (TXDIV)
Baseband or antenna hopping cannot be enabled at the
same time with TX Diversity Time Shift (TXDIV).
708
RNW OBJECT RESERVED FOR PLAN ACTIVATION
The RNW object is reserved for plan activation.
709
THE COUNT OF CCH SETUP-ENABLED WCELS
EXCEEDS THE LICENSE CCHSETUP CAPACITY LIMIT
The count of CCH Setup-enabled WCELs exceeds the
license CCHSetup capacity limit.
710
WCEL-POWERSAVEHSPATYPE CAN BE SET ONLY
WHEN WCEL-HSDPAENABLED AND WCELHSUPAENABLED ARE ENABLED
WCEL-PowerSaveHSPAType can be set only when
WCEL-HSDPAEnabled and WCEL-HSUPAEnabled are
enabled.
711
74
WCEL-POWERSAVEHSPATYPE CANNOT BE MODIFIED
IF WBTS-NESWVERSION IS LESS THAN WN6.0
DN987378
Issue: 30-0
General Error Messages of System
Error messages
WCEL-PowerSaveHSPAType cannot be set if WBTSNESWversion is less than WN6.0.
712
PORT NONEXISTENT
Port does not exist in EQUIPM.
713
WCEL-RACH_TX_NB01MIN PARAMETER VALUE MUST
BE LESS THAN THE VALUE OF WCELRACH_TX_NB01MAX PARAMETER
WCEL-RACH_Tx_NB01min parameter value must be less
than the value of the WCEL-RACH_Tx_NB01max
parameter.
714
WCEL- PTXTARGETPSMAX MUST BE GREATER THAN
OR EQUAL TO WCEL- PTXTARGETPSMIN
WCEL- PtxTargetPSMax must be greater than or equal to
WCEL- PtxTargetPSMin.
715
WCEL-FACHLOADMARGINCCH MUST BE LESS THAN
WCEL-FACHLOADTHRESHOLDCCH
WCEL-FachLoadMarginCCH must be less than WCELFachLoadThresholdCCH.
716
WCEL-RACHLOADMARGINCCH MUST BE LESS THAN
WCEL-RACHLOADTHRESHOLDCCH
WCEL-RachLoadMarginCCH must be less than WCELRachLoadThresholdCCH.
717
VALUE OF FMCS-HHORSCPCANCEL MUST BE
HIGHER THAN VALUE OF FMCSHHORSCPTHRESHOLD
The value of FMCS-HHoRscpCancel must be higher than
the value of FMCS-HHoRscpThreshold.
718
FMCI-INTERFREQNCELLSEARCHPERIOD MUST BE
LOWER THAN FMCI-INTERFREQMAXMEASPERIOD
FMCI-InterFreqNcellSearchPeriod must be lower than
FMCI-InterFreqMaxMeasPeriod.
719
VALUE OF FMCG-GSMNCELLSEARCHPERIOD MUST
BE LOWER THAN VALUE OF FMCGGSMMAXMEASPERIOD
The value of FMCG-GsmNcellSearchPeriod must be lower
than the value of FMCG-GsmMaxMeasPeriod.
720
Issue: 30-0
WSMLC-PREFERRED AGPS METHOD CAN BE
NETWORK BASED ONLY WHEN WSMLC-NETWORK
BASED AGPS IS ENABLED
DN987378
75
Error messages
General Error Messages of System
WSMLC-preferred AGPS method can be network based
only when WSMLC-network based AGPS is enabled.
721
WSMLC-PREFERRED AGPS METHOD CAN BE UE
BASED ONLY WHEN WSMLC-UE BASED AGPS IS
ENABLED
WSMLC-preferred AGPS method can be UE based only
when WSMLC-UE based AGPS is enabled.
722
WSMLC-NETWORKBASEDAGPS CAN BE ENABLED
ONLY IF WSMLC-LCSINTERFACEOPTION IS SET TO
IUPC
WSMLC-NetworkBasedAGPS can be enabled only if
WSMLC-LCSInterfaceOption is set to IUPC.
723
WCEL-PTXFDPCHMAX PARAMETER MUST NOT BE
GREATER THAN WCEL-PTXFDPCHMIN PARAMETER
WCEL-PtxFDPCHMax parameter must not be greater than
value of the WCEL-PtxFDPCHMin parameter.
724
BCF ID MISMATCH IN ETP
BCF ID mismatch in ETP.
725
HDLC LINK ID MISMATCH IN ETP
HDLC link ID is mismatched in ETP.
726
LCP STATE MISMATCH IN ETP
LCP state mismatch in ETP
727
PARAMETER OUT OF RANGE IN ETP
The parameter is out of range in ETP.
728
HDLC LINK ESTABLISHMENT FAILURE IN ETP
HDLC link establishment is failed in ETP.
729
NCP ESTABLISHMENT FAILURE IN ETP
NCP establishment is failed in ETP.
730
FPGA DEVICE ERROR IN ETP
FPGA device error in ETP
731
PCU ID MISMATCH IN ETP
The PCU ID mismatches in ETP.
732
76
IP ADDRESS MISMATCH IN ETP
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Error occurs when BTS M-plane IP address in ETP is
different than the BTS M-plane address which are received
from BTS when negotiating the ML-PPP link to get up.
733
MAXIMUM COUNT OF ABIS HDLC LINK TO ETP
EXCEEDED
The maximum count of Abis HDLC link to ETP is
exceeded.
734
MAX PCU2 ALREADY CONNECTED WITH ETP
The maximum number of PCU2 has been connected with
ETP already.
735
ETP IS OVERLOADED
ETP is overloaded so request could not be processed.
736
MESSAGE VALIDATION IS FAILED AT ETP
Message validation is failed at ETP.
737
ETP DSP IS DOWN
ETP DSP is down so request could not be processed.
738
CONFLICT IN HEADER COMPRESSION
Conflict exists in header compression.
739
HDLC LINK EXISTS IN ETP
HDLC link already exists in ETP.
740
SUB-BCF EXISTS FOR THIS CONNECTION
Sub-BCF exists for this connection.
741
IN0 CONFIGURATION INVALID OR MISSING FROM
ETPE/T
IN0 configuration is invalid or missing from ETPE/T.
742
ADJI-ADJIUARFCN IS NOT MODIFIABLE IF TARGET
CELL IS UNDER OWN RNC
ADJI-AdjiUARFCN is not modifiable if target cell is under
own RNC.
743
COUNT OF IP SUBNET BINDING TO EACH EVC
EXCEEDED MAXIMUM NUMBER
Count of IP subnet binding to each EVC is exceeded the
maximum number.
744
Issue: 30-0
IP SUBNET ALREADY EXISTS
DN987378
77
Error messages
General Error Messages of System
IP subnet already exists.
745
MIMO NOT AVAILABLE
For RAN 1642, MIMO 28mbps feature is not available.
746
DC HSDPA NOT AVAILABLE
For RAN 1906, Multi Cell Operation is not available.
747
XIP SQLITE DATABASE SYSTEM ERROR
XIP SQLITE database system error.
748
COMMAND PARTLY SUCCESSFUL: APN NOTIF NOT
SENT
Sending of APN data modification notification to external
server (e.g. NTMS) failed. However, the data has been
stored in the HLR database.
749
COMMAND PARTLY SUCCESSFUL: SGSN NOT
UPDATED AND APN NOTIF FAILED
The data cannot be transferred to SGSN correctly. The
MAP interface rejects the given operation. Also, APN data
modification notification to external server (e.g. NTMS)
failed. However, the data has been stored in the HLR
database.
750
INVALID CONTROLLING GROUP
Controlling group is invalid.
751
THERE ARE TOO MANY ITEMS IN LINKED GROUP LIST
There are too many items in the linked group list.
752
INVALID GTSI IN LINKED GROUP LIST
It is the invalid GTSI in the linked group list.
753
THE FOREIGN GTSI IS ALREADY LINKED TO A LOCAL
GROUP
The foreign GTSI is already linked to a local group.
754
SEVERAL GROUPS FROM THE SAME SWMI ARE IN
THE LINKED GROUP LIST
Several groups from the same SWMI are in the linked
group list.
755
THE COVER GROUP CANNOT HAVE THE ISI LINK
The cover group cannot have the ISI link.
756
78
THE ISI LINKED GROUP CANNOT BE COVER GROUP
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The ISI linked group cannot be cover group.
757
RRA CELL MANAGER'S PID DOES NOT EXIST IN
DATABASE
RRA Cell Manager's pid does not exist in database.
758
OSC DHR FEATURE IS NOT IN USE IN BSC
OSC DHR (Orthogonal Sub-channel Double Half Rate)
feature cannot be enabled due to that there is no license
installed in BSC (Base Station Controller) or license has
been expired or license is in wrong state.
759
OSC DHR CAPACITY LICENSE EXCEEDED
Capacity of the OSC DHR (Orthogonal Subchannel Double
Half Rate) license exceeded.
760
OSC DHR CANNOT OPERATE WITHOUT AMR-HR
OSC DHR (Orthogonal Subchannel Double Half Rate)
feature cannot operate without the AMR HR packing in
use.
761
LIMIT FOR TRIGGERING OSC DHR MULTIPLEXING
HAS TO BE <= LOWER LIMIT CRITERION OF AMR HR
PACKING IN SEGMENT
When Double Half Rate is in use in a BTS (Base
Transceiver Station), parameter Limit for Triggering OSC
DHR Multiplexing has to be less than or equal to the used
lower limit criterion of AMR HR (Adaptive Multi Rate Half
Rate) packing in the segment.
762
LIMIT FOR TRIGGERING OSC DHR MULTIPLEXING
HAS TO BE <= LOWER LIMIT CRITERION OF AMR HR
PACKING IN BSC
When Double Half Rate is in use in a BTS (Base
Transceiver Station), parameter Limit for Triggering OSC
DHR Multiplexing has to be less than or equal to the used
lower limit criterion of AMR HR (Adaptive Multi Rate Half
Rate) packing in the BSC.
763
CSDAP FEATURE IS NOT IN USE IN BSC
CSDAP (Circuit Switched Dynamic Abis Pool) feature
cannot be used due to that there is no license installed in
BSC (Base Station Controller) or license has been expired
or license is in wrong state.
764
CSDAP CAPACITY LICENSE EXCEEDED
Capacity of the CSDAP (Circuit Switched Dynamic Abis
Pool) license exceeded.
Issue: 30-0
DN987378
79
Error messages
General Error Messages of System
765
DSCC FEATURE IS NOT IN USE IN BSC
DSCC feature cannot be used due to that there is no
license installed in BSC (Base Station Controller) or
license has been expired or license is in wrong state.
766
BTS SOFTWARE DOES NOT SUPPORT OSC DHR
FEATURE
BTS software does not support OSC DHR (Orthogonal
Sub Channel Double Half Rate) feature.
767
OSC CANNOT OPERATE WITHOUT RX DIVERSITY
OSC (Orthogonal Sub Channel) DHR/DFR feature cannot
operate without RX diversity in use.
768
GENERAL ERROR OF RECOVERY
The general fault situation indicator of the recovery
system.
769
WAIT FOR UNIT RESTART PERMISSION
The unit restart is not possible due to the states of other
functional units.
770
NO RESPONSE TO SUPERVISION MESSAGE
The program block has not answered the supervision
message.
771
BAD RESPONSE TO SUPERVISION MESSAGE
The program block has detected a fault situation on startup, or the program block is in an incorrect working state.
772
NO RESPONSE TO LOADING INQUIRY
The USAPRO program block of the source has not
acknowledged the loading inquiry.
773
NO LOAD GROUPS FOUND
The load group has not been found in the file loading list
file (FLLIST) or in the load group file (LGROUP).
774
ERRORS IN LOADING PARAMETERS
The control parameters of loading are incorrect.
775
NO RESPONSE TO LOAD COMMAND
The program block performing the loading has not
acknowledged the loading command. The total time limit of
loading has expired.
776
80
FILES NOT READABLE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The files of the source are not in order. Loading is not
allowed.
777
SOURCE NOT READY
The source is still in the starting state. Loading is not
allowed.
778
SOURCE NOT USABLE
The source is in a working state in which loading is not
allowed.
779
FAMILY UPDATING FAILURE
Updating has not started in the active unit. The process
family has acknowledged with the NOK status, or the time
limit has expired.
780
FAMILY WARM-UP FAILURE
The warm-up of a process family has failed. The process
family has acknowledged with the NOK status, or the time
limit has expired.
781
FAMILY STATE NOT CHANGED
The process family has not changed its working state, or
the time limit of acknowledgement has expired.
782
FAMILY NOT READY FOR SWITCHOVER
The process family is not ready for switchover, or the time
limit of acknowledgement has expired.
783
UNIT STATE INCORRECT
The definition of unit working state has failed. The unit is in
an incorrect working state.
784
ERRORS IN TASK DRIVER PARAMETERS IN RCPARA
The control parameters of the execution automaton of the
USAPRO program block are incorrect.
785
JOB NOT ACCEPTED
A task concerning unit state administration is not possible
due to another task in progress or due to the working state
of the unit.
786
SIGNALLING TRAFFIC NOT REMOVED
Removal of signalling traffic has failed.
787
SIGNALLING TRAFFIC NOT STARTED
Starting of signalling traffic has failed.
Issue: 30-0
DN987378
81
Error messages
General Error Messages of System
788
WAIT FOR OUTPUT
The RCXPRO program block requests to stop the MML
session because of unit restart.
789
RECOVERY FUNCTION BUSY
The RCXPRO program block is reserved for another
recovery function.
790
DATA MISMATCH
An error has occurred in the task analysis.
791
NO RESPONSE FROM UNIT
No acknowledgement to the sent message is received
from the unit within the time limit.
792
BAD RESPONSE FROM UNIT
A negative acknowledgement is received to the sent
message.
793
TIME-OUT TRIGGER FAILURE
The time limit has expired.
794
DUE TO ACTUAL STATES IN UNITS
The units are in such working states that the task is not
possible.
795
TRANSITION NOT CONTROLLED
The task is not possible controlled.
796
DUE TO MINIMUM CONFIGURATION
The task is not possible controlled since the minimum
configuration of units would not be reached.
797
OWN UNIT NOT IN NORMAL WORKING STATE
The working state of own unit prevents the task.
798
UNIT IN TEST
The unit is in test.
799
UNIT IN CALIBRATION
The unit is in calibration.
800
SPARE UNIT NOT FOUND
No working spare unit is found for the unit.
801
82
UNIT HAS NO LINES TO SERVE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The unit has no external speech lines to be served.
802
RECOVERY FUNCTION FAILURE
A recovery function has been interrupted due to an error.
803
SWITCHOVER FAILURE
The switchover has failed in the unit.
804
WARM UP FAILURE
The warm-up of the spare unit has failed.
805
UNIT RESTART FAILURE
The USAPRO program block has detected an error in the
unit restart.
806
UNIT LOADING FAILURE
The unit start-up has failed in file loading.
807
UNIT RESTART FAILED
The final start-up of the unit has failed.
808
INITIALIZATION FAILURE IN SYSTEM RESTART
The exchange restart has failed at the initialization stage.
809
SCDFLE ERROR IN UNIT
The SCDFLE file is incorrect in the unit.
810
SCDFLE UPDATING FAILURE
An error has occurred in the SCDFLE file update.
811
PCMCON DIFFERS FROM SCDFLE
The PCMCON and SCDFLE files contain contradictory
data.
812
SCDFLE STATE CONFLICT
There is a conflict between unit working states in the
SCDFLE file.
813
CONNECTIONS ARE NOT RELEASED
The connections of a timeslot-based unit are not released.
814
PCMCON DIFFERS IN UNITS
The contents in the PCMCON file varies in different units.
815
Issue: 30-0
HARDWARE SWITCHOVER CONTROL FAILURE
DN987378
83
Error messages
General Error Messages of System
The control of switchover logic has failed.
816
FAILURE IN CALL CLEARING
The call clearing has failed.
817
FAILURE IN ASS CHANNEL STATE CONTROL
The state transition of an ASS channel has failed. The
opening or closing of an ASS channel has failed, or the
files of the accused program block (e.g. ASMANA) are
incorrect.
818
ASS CHANNEL UNIT STATE CONTROL FAILURE
The state transition of a unit connected to an ASS channel
has failed. It is possible that the ASS channel of the unit is
closed, or no acknowledgement is received to the state
transition command from the unit. The error may also be in
the ASS channel files.
819
LIBRARY INITIALIZATION FAILURE
When starting up, the library manager has noticed an error
in the initialization of a library that it is responsible for. The
fault may be a missing file, or an error in the files or tables
to be initialized.
820
HOT RESET NOT ACCEPTED
The hot reset of the unit is not possible. The unit is still on
the starting-up phase.
821
REWARMING IN PROGRESS
The rewarming of a process family or an individual process
is in progress.
822
OMU IS NOT ON TRIAL SIDE
The OMU is not on trial side.
823
ILLEGAL TRIAL SIDE
An illegal trial side. An attempt has been made to add the
unit into trial from the wrong side of the two OMU units.
824
MAINTENANCE COMPUTER NOT ACTIVATED
The new maintenance computer does not activate.
825
TRIAL_MSG_S MESSAGE FAILURE
No acknowledgement to the TRIAL_MSG_S message has
been received from the maintenance computer of the other
side of the exchange.
84
DN987378
Issue: 30-0
General Error Messages of System
826
Error messages
SUITABLE TRIAL UNIT NOT FOUND
A suitable trial unit is not found.
827
SUITABLE NOSWITCH UNIT NOT FOUND
A suitable NOSWITCH unit is not found for trial.
828
UNIT IS NOT IN TRIAL
The unit is not in trial.
829
TRIAL UNIT NOT FOUND
The trial unit is not found.
830
NOSWITCH UNIT NOT FOUND
The NOSWITCH unit is not found.
831
MAINTENANCE COMPUTER NOT FOUND
The maintenance computer of the other side not found.
832
EXCHANGE IS NOT SPLIT
The exchange is not split up.
833
TRAFF_SWITCHOVER_UNIT_S MESSAGE FAIL
No OK acknowledgement is received to the message
TRAFF_SWITCHOVER_UNIT_S.
834
RESTART_TO_UNIT_S MESSAGE FAIL
No OK acknowledgement is received to the message
RESTART_TO_UNIT_S.
835
OMU IS IN TRIAL
The OMU is in trial.
836
UNITS IN BL-STATE ARE NOT IDLE
The units in BL-state are not ready for traffic switchover.
837
OMU HAS NOT NEW PACK
The new package has not been loaded into the OMU.
838
UNIT IS IN TRIAL
The unit is in trial.
839
CM/CAC NOT IN TRIAL
The central memory unit (CM/CAC) is not in trial.
Issue: 30-0
DN987378
85
Error messages
General Error Messages of System
840
UNITS IN ILLEGAL STATE AND NOT READY FOR
TRAFFIC SWITCHOVER
Some units are not in the normal working state and, thus,
not ready for traffic switchover or for starting the splitting of
the exchange.
841
TWO REPLACEABLE N+1 UNITS HAVE IDENTICAL
LOGICAL ADDRESS IN SCDFLE
Two replaceable N+1 units have an identical logical
address in the SCDFLE file.
842
MODIFICATION OF MB TO LOGICAL ADDRESS FAILED
Modification of a message bus address into a logical
address has failed.
843
LOGICAL ADDRESSES OF N+1 REPLACEABLE UNITS
ARE DIFFERENT IN DATA BANK UNIT.
The logical addresses of N+1 replaceable units are
different in the data bank unit.
844
FAILURE IN MAINTENANCE OF CALL CONTROL
A failure in the maintenance of the call control. The failure
is due tothe change of state in question and can result e.g
in a failure to clear the calls in the faulty unit, or in a failure
to establish new ones in the unit to be taken into use.
845
FAILURE IN D-CHANNEL STATE CONTROL
The state change of a D channel has failed. The opening
or closing of a D channel has not succeeded, or the files of
the accused program block (e.g. PXNETM) are faulty.
846
D-CHANNEL UNIT STATE CONTROL FAILURE
The state change of a unit connected to the D-channel has
failed. It is possible that the D-channel of the unit is closed,
or no acknowledgement is received to the state change
command. The fault may also be in the D-channel files.
847
SCDFLE CORRUPTED IN UNIT
The SCDFLE file is corrupted in the unit.
848
CREATE OR REMOVE FAILED TO SCDFLE IN UNIT
Creating or removing of some unit failed in the SCDFLE
file of the unit.
849
UNIT IN EMERGENCY MODE
Unit of RSS is in emergency mode.
86
DN987378
Issue: 30-0
General Error Messages of System
850
Error messages
RECOVERY FUNCTION CANCELLED BY ANOTHER
RECOVERY FUNCTION
A recovery function has been cancelled by another
recovery function.
851
WARMING PAIR IS BROKEN UP
The warming pair of a unit with N+1 redundancy is broken
up by a unit failure.
852
SAVING OF EXCITATION IS NOT SUCCESSFUL
The saving of an excitation was not successful.
853
THE BCF INTERFACE OF THE FIRST CSDAP IS NOT IN
USE IN BTS SITE
Abis Interface is not in use in BCF. This cause code refers
to the first CSDAP.
854
THE BCF INTERFACE OF THE SECOND CSDAP IS NOT
IN USE IN BTS SITE
Abis interface is not in use in BCF. This cause code refers
to the second CSDAP.
855
THE BCF INTERFACE OF THE THIRD CSDAP IS NOT IN
USE IN BTS SITE
Abis interface is not in use in BCF. This cause code refers
to the third CSDAP.
856
THE BCF INTERFACE OF THE FOURTH CSDAP IS NOT
IN USE IN BTS SITE
Abis interface is not in use in BCF. This cause code refers
to the fourth CSDAP.
857
THE TIMESLOT OF THE FIRST CSDAP EXCEEDS THE
E1/T1 BOUNDS
CSDAP timeslots exceed the E1/T1 bounds. This cause
code refers to the first CSDAP.
858
THE TIMESLOT OF THE SECOND CSDAP EXCEEDS
THE E1/T1 BOUNDS
CSDAP timeslots exceed the E1/T1 bounds. This cause
code refers to the second CSDAP.
859
THE TIMESLOT OF THE THIRD CSDAP EXCEEDS THE
E1/T1 BOUNDS
CSDAP timeslots exceed the E1/T1 bounds. This cause
code refers to the third CSDAP.
Issue: 30-0
DN987378
87
Error messages
General Error Messages of System
860
THE TIMESLOT OF THE FOURTH CSDAP EXCEEDS
THE E1/T1 BOUNDS
CSDAP timeslots exceed the E1/T1 bounds. This cause
code refers to the fourth CSDAP.
861
THE FIRST CSDAP TIMESLOT IS OVERLAPPING WITH
OTHER ABIS RESOURCES
CSDAP timeslot are overlapping with other Abis resources.
This cause code refers to the first CSDAP.
862
THE SECOND CSDAP TIMESLOT IS OVERLAPPING
WITH OTHER ABIS RESOURCES
CSDAP timeslot are overlapping with other Abis resources.
This cause code refers to the second CSDAP.
863
THE THIRD CSDAP TIMESLOT IS OVERLAPPING WITH
OTHER ABIS RESOURCES
CSDAP timeslot are overlapping with other Abis resources.
This cause code refers to the third CSDAP.
864
THE FOURTH CSDAP TIMESLOT IS OVERLAPPING
WITH OTHER ABIS RESOURCES
CSDAP timeslot are overlapping with other Abis resources.
This cause code refers to the fourth CSDAP.
865
CSDAP RESOURCES ARE UNAVAILABLE
CSDAP does not exist or the timeslot does not belong to
CSDAP.
866
R99 AMR CALL IS ESTABLISHED ON CDSP-C CARD
R99 AMR call is established on CDSP-C card.
867
ET INDEX IS NOT FREE FOR THIS LETGR
ET index is not free for the configuring LETGR. The
possible reason is that ET is occupied by another unit like
IWS1E/T etc.
868
MODIFICATION IS NOT ALLOWED WHEN THERE ARE
SOME CELLS ATTACHED INTO PCU
Modification is not allowed when there are some cells
attached into PCU. You shall disable GPRS from those
cells.
869
IUR-HSPAOVERIUR CAN BE ENABLED ONLY WHEN
RNFC-HSDPAMOBILITY IS ENABLED
IUR-HSPAOverIUR can be enabled only when RNFCHSDPAMobility is enabled
88
DN987378
Issue: 30-0
General Error Messages of System
870
Error messages
IUR-HSPAOVERIUR CAN BE ENABLED ONLY WHEN
RNFC-HSDPADYNAMICRESOURCEALLOCATION IS
ENABLED
IUR-HSPAOverIUR can be enabled only when RNFCHSDPADynamicResourceAllocation is enabled
871
IUR-HSPAOVERIUR CAN BE ENABLED ONLY WHEN
VALUE OF IUR-NRNCVERSION IS GREATER OR
EQUAL TO REL6
IUR-HSPAOverIUR can be enabled only when the value of
IUR-NRncVersion is greater or equal to Rel6.
872
VCEL-HSDPAFMCSIDENTIFIER MUST BE DEFINED IF
VCEL-HSDPAENABLED IS ENABLED
VCEL-HSDPAFmcsIdentifier must be defined if VCELHSDPAenabled is enabled.
873
VCEL-HSDPAFMCIIDENTIFIER MUST BE DEFINED IF
VCEL-HSDPAENABLED IS ENABLED
VCEL-HSDPAFmciIdentifier must be defined if VCELHSDPAenabled is enabled.
874
VCEL-HSDPAFMCGIDENTIFIER MUST BE DEFINED IF
VCEL-HSDPAENABLED IS ENABLED
VCEL-HSDPAFmcgIdentifier must be defined if VCELHSDPAenabled is enabled.
875
VCEL-HSDPAHOPSIDENTIFIER MUST BE DEFINED IF
VCEL-HSDPAENABLED IS ENABLED
VCEL-HSDPAHopsIdentifier must be defined if VCELHSDPAenabled is enabled.
876
VCEL-RTWITHHSDPAFMCSIDENTIFIER MUST BE
DEFINED IF VCEL-HSDPAENABLED IS ENABLED
VCEL-RTwithHSDPAFmcsIdentifier must be defined if
VCEL-HSDPAenabled is enabled.
877
VCEL-RTWITHHSDPAFMCIIDENTIFIER MUST BE
DEFINED IF VCEL-HSDPAENABLED IS ENABLED
VCEL-RTwithHSDPAFmciIdentifier must be defined if
VCEL-HSDPAenabled is enabled.
878
VCEL-RTWITHHSDPAFMCGIDENTIFIER MUST BE
DEFINED IF VCEL-HSDPAENABLED IS ENABLED
VCEL-RTwithHSDPAFmcgIdentifier must be defined if
VCEL-HSDPAenabled is enabled.
Issue: 30-0
DN987378
89
Error messages
General Error Messages of System
879
VCEL-RTWITHHSDPAHOPSIDENTIFIER MUST BE
DEFINED IF VCEL-HSDPAENABLED IS ENABLED
VCEL-RTwithHSDPAHopsIdentifier must be defined if
VCEL-HSDPAenabled is enabled.
880
VCEL-HSPAFMCSIDENTIFIER MUST BE DEFINED IF
VCEL-HSUPAENABLED IS ENABLED
VCEL-HSPAFmcsIdentifier must be defined if VCELHSUPAenabled is enabled.
881
VCEL-RTWITHHSPAFMCSIDENTIFIER MUST BE
DEFINED IF VCEL-HSUPAENABLED IS ENABLED
VCEL-RTwithHSPAFmcsIdentifier must be defined if
VCEL-HSUPAenabled is enabled.
882
VCEL-RTWITHHSDPAFMCSIDENTIFIER MUST BE
DEFINED IF RNC-AMRWITHHSDSCH IS ENABLED
VCEL-RTwithHSDPAFmcsIdentifier must be defined if
RNC-AMRWithHSDSCH is enabled.
883
VCEL-RTWITHHSDPAFMCIIDENTIFIER MUST BE
DEFINED IF RNC-AMRWITHHSDSCH IS ENABLED
VCEL-RTwithHSDPAFmciIdentifier must be defined if
RNC-AMRWithHSDSCH is enabled.
884
VCEL-RTWITHHSDPAFMCGIDENTIFIER MUST BE
DEFINED IF RNC-AMRWITHHSDSCH IS ENABLED
VCEL-RTwithHSDPAFmcgdentifier must be defined if
RNC-AMRWithHSDSCH is enabled.
885
VCEL-RTWITHHSDPAHOPSIDENTIFIER MUST BE
DEFINED IF RNC-AMRWITHHSDSCH IS ENABLED
VCEL-RTwithHSDPAHopsIdentifier must be defined if
RNC-AMRWithHSDSCH is enabled.
886
VCEL-RTWITHHSPAFMCSIDENTIFIER MUST BE
DEFINED IF RNC-AMRWITHHSDSCH IS ENABLED
RTwithHSPAFmcsIdentifier must be defined if RNCAMRWithHSDSCH is enabled.
887
NO ANSWER RECEIVED FROM UER IN TIME
No answer is received from uer in time.
888
TQM IS CONNECTED WITH SOME IUR
TQM is connected with some IUR.
889
90
DSP SPECIFIC TASK QUEUE IS FULL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
DSP specific task queue is full. (RM3PRB service queuing
error)
890
MAIN TASK QUEUE IS FULL
Main task queue is full. (RM3PRB service queuing error)
891
WCEL-MIMOENABLED CAN BE ENABLED ONLY WHEN
RNFC-FRLCENABLED IS ENABLED
WCEL-MIMOEnabled can be enabled only when RNFCFRLCEnabled is enabled
892
WCEL-MIMOENABLED CAN BE ENABLED ONLY WHEN
WBTS-HSDPA14MBPSPERUSER IS ENABLED
WCEL-MIMOEnabled can be enabled only when WBTSHSDPA14MbpsPerUser is enabled.
893
WCEL-MIMOENABLED CAN BE ENABLED ONLY WHEN
WCEL-FDPCHENABLED IS ENABLED
WCEL-MIMOEnabled can be enabled only when WCELFDPCHEnabled is enabled.
894
LICENSE STATE OF MIMO 28MBPS MUST BE ON FOR
CELL UNLOCKING WHEN WCEL-MIMOENABLED IS
ENABLED
License state of MIMO 28Mbps must be on for cell
unlocking when WCEL-MIMOEnabled is enabled.
895
THE NUMBER OF MIMO 28MBPS SUPPORT-ENABLED
WCELS EXCEEDED THE LICENSED CAPACITY
The number of MIMO 28Mbps support-enabled WCELs
must not exceed the licensed capacity.
896
AN ERROR OCCURRED WHEN OPENING A DATABASE
FILE
An error occurred when opening a database file.
897
A DATABASE ERROR OCCURRED WHEN CREATING A
TABLE
A database error occurred when creating a table.
898
A DATABASE ERROR OCCURRED WHEN EXECUTING
AN SQL SELECT STATEMENT
A database error occurred when executing an SQL select
statement.
899
Issue: 30-0
A DATABASE ERROR OCCURRED WHEN EXECUTING
AN SQL INSERT STATEMENT
DN987378
91
Error messages
General Error Messages of System
A database error occurred when executing an SQL insert
statement.
900
A DATABASE ERROR OCCURRED WHEN EXECUTING
AN SQL DELETE STATEMENT
A database error occurred when executing an SQL delete
statement.
901
IBTS SHARING OR INTER-RNC CELL CHANGE
LICENSE STATE MUST BE ON FOR VBTS OR VCEL
OBJECT MANAGEMENT
For VBTS or VCEL object management, IBTS sharing or
inter-RNC cell change license state must be on.
902
IU OBJECT CANNOT BE DELETED WHEN IUSTATE IS
OTHER THAN BAR-US
IU object cannot be deleted when IuState is other than
BAR-US.
903
SWITCHOVER DENIED: TARGET 2N UNITS CONTAIN A
DEFAULT ACTIVE UNIT IN WO STATE AND REVERTIVE
SWITCHOVER IS ON
The switchover is denied. Target 2N units contain a default
active unit in WO state and revertive switchover is on.
904
IU OBJECT CANNOT BE MODIFIED IF THE IU PRIMARY
OR SECONDARY PLMN CONFIGURED CONFLICTS
WITH RNC-CBC LIST
IU object cannot be modified if the IU primary or secondary
PLMN configured conflicts with RNC-CBC list.
905
WCEL-DCELLHSDPAENABLED CAN BE ENABLED
ONLY WHEN RNFC-FRLCENABLED IS ENABLED
WCEL-DCellHSDPAEnabled can be enabled only when
RNFC-FRLCEnabled is enabled
906
WCEL-DCELLHSDPAENABLED CAN BE ENABLED
ONLY WHEN WBTS- HSDPA14MBPSPERUSER IS
ENABLED
WCEL-DCellHSDPAEnabled can be enabled only when
WBTS-HSDPA14MbpsPerUser is enabled.
907
WCEL-DCELLHSDPAENABLED CAN BE ENABLED
ONLY WHEN WCEL-MIMOENABLED IS DISABLED IN
ALL CELLS UNDER WBTS
WCEL-DCellHSDPAEnabled can be enabled only when
WCEL-MIMOEnabled is disabled in all cells under WBTS.
92
DN987378
Issue: 30-0
General Error Messages of System
908
Error messages
WCEL-DCELLHSDPAENABLED CAN BE ENABLED
ONLY WHEN WCEL-FDPCHENABLED IS ENABLED
WCEL-DCellHSDPAEnabled can be enabled only when
WCEL-FDPCHEnabled is enabled.
909
WCEL-DCELLHSDPAENABLED CAN BE ENABLED
ONLY WHEN WCEL-HSUPAENABLED IS ENABLED
WCEL-DCellHSDPAEnabled can be enabled only when
WCEL-HSUPAEnabled is enabled.
910
TWO CELLS FORMING A DC HSDPA PAIR SHOULD BE
IN THE SAME FREQUENCY BAND
Two cells forming a DC HSDPA pair should be in the same
frequency band.
911
TWO CELLS FORMING DC HSDPA PAIR SHOULD HAVE
ADJACENT FREQUENCIES WITHIN SAME
FREQUENCY BAND
Two cells forming DC HSDPA pair should have adjacent
frequencies within same frequency band.
912
CELLS FORMING DC HSDPA PAIR SHOULD HAVE
SAME VALUE OF SECTOR ID, TCELL AND ADJ
FREQUENCY IN SAME FREQ BAND
Cells forming DC HSDPA pair should have same value of
Sector ID, Tcell and ADJ frequency in the same freq band.
913
CELLS FORMING DC HSDPA PAIRS SHOULD HAVE
THE SAME VALUE OF WCEL-HSPAQOSENABLED
PARAMETER
Cells forming DC HSDPA pairs should have the same
value of WCEL-HSPAQoSEnabled parameter.
914
LICENSE STATE OF DC HSDPA MUST BE ON FOR
CELL UNLOCKING WHEN WCELDCELLHSDPAENABLED IS SET TO ENABLE
License state of DC HSDPA must be ON for cell unlocking
when WCEL-DCellHSDPAEnabled is set to enable.
915
THE NUMBER OF DC HSDPA-ENABLED CELLS MUST
NOT EXCEED THE LICENSE CAPACITY
The number of DC HSDPA-enabled cells must not exceed
the license capacity.
916
Issue: 30-0
DC HSDPA FEATURE CAN BE ENABLED IF HSDPA 15
CODES FEATURE WITH AT LEAST 10 CODE LICENSE
IS ACTIVATED IN BTS
DN987378
93
Error messages
General Error Messages of System
DC HSDPA Feature can be enabled if HSDPA 15 Codes
feature with at least 10-code-license is activated in BTS.
918
VCEL-RTWITHHSDPAHOPSIDENTIFIER MUST BE
DEFINED IF RNFC-AMRWITHHSDSCH AND VCELHSDPAENABLED ARE ENABLED
VCEL-RTwithHSDPAHopsIdentifier must be defined if
RNFC-AMRWithHSDSCH and VCEL-HSDPAenabled are
enabled.
919
VCEL-RTWITHHSDPAFMCGIDENTIFIER MUST BE
DEFINED IF RNFC-AMRWITHHSDSCH AND VCELHSDPAENABLED ARE ENABLED
VCEL-RTwithHSDPAFmcgIdentifier must be defined if
RNFC-AMRWithHSDSCH and VCEL-HSDPAenabled are
enabled.
920
VCEL-RTWITHHSDPAFMCIIDENTIFIER MUST BE
DEFINED IF RNFC-AMRWITHHSDSCH AND VCELHSDPAENABLED ARE ENABLED
VCEL-RTwithHSDPAFmciIdentifier must be defined if
RNFC-AMRWithHSDSCH and VCEL-HSDPAenabled are
enabled
921
VCEL-RTWITHHSDPAFMCSIDENTIFIER MUST BE
DEFINED IF RNFC-AMRWITHHSDSCH AND VCELHSDPAENABLED ARE ENABLED
VCEL-RTwithHSDPAFmcsIdentifier must be defined if
RNFC-AMRWithHSDSCH and VCEL-HSDPAenabled are
enabled.
922
WRONG INTERFACE MODE
Wrong interface mode.
923
WCEL-HSUPA2MSTTIENABLED CAN BE ENABLED
ONLY WHEN CDSP-DH CARD EXIST IN UPGRADE
MODE
WCEL-HSUPA2MSTTIEnabled can be enabled only when
CDSP-DH card exist in upgrade mode.
924
HOPL CANNOT BE DELETED IF USED BY ADJL
HOPL cannot be deleted if it is used by ADJL.
925
ABSPRIOCELLRESELEC AND
ADJLABSPRIOCELLRESELEC ALWAYS HAVE UNIQUE
VALUES.
AbsPrioCellReselec and AdjLAbsPrioCellReselec always
have unique values.
94
DN987378
Issue: 30-0
General Error Messages of System
926
Error messages
HOPL NOT FOUND
HOPL NOT FOUND
927
HOPL ALREADY CREATED
HOPL ALREADY CREATED
928
HOPL COLLECTION FULL
HOPL COLLECTION FULL
929
ADJL NOT FOUND
ADJL NOT FOUND
930
ADJL COLLECTION FULL
ADJL COLLECTION FULL
931
MAXIMUM OF ADJLs FOR WCEL
MAXIMUM OF ADJLs FOR WCEL
932
ADJL ALREADY CREATED UNDER WCEL
ADJL ALREADY CREATED UNDER WCEL
933
WCEL-HSCAPABILITYHOPERIOD MUST BE SET AS 0
IF WCEL-DCELLHSDPACAPAHO IS ENABLED
WCEL-HSCapabilityHOPeriod must be set as 0 if WCELDCellHSDPACapaHO is enabled.
934
WCEL-DCELLHSDPAENABLED CAN BE ENABLED
ONLY WHEN RNFC-HSDPAMOBILITY IS ENABLED
WCEL-DCellHSDPAEnabled can be enabled only when
RNFC-HSDPAMobility is enabled
935
IP ADDRESS ATTRIBUTE ALREADY EXISTS
The IP address attribute already exists.
936
PACKET ABIS FEATURE IS NOT SUPPORTED FOR
THIS BTS SITE TYPE
PACKET ABIS FEATURE IS NOT SUPPORTED FOR
THIS BTS SITE TYPE.
937
BTS SOFTWARE DOES NOT SUPPORT PACKET ABIS
FEATURE
BTS software does not support Packet ABIS feature
938
WRONG D-CHANNEL TYPE
WRONG D-CHANNEL TYPE
Issue: 30-0
DN987378
95
Error messages
General Error Messages of System
939
DURING WCEL MODIFICATION,SECTORID CANNOT BE
MODIFIED IF DCELLHSDPAENABLED PARAMETER IS
ALREADY ENABLED
During WCEL modification,SectorId cannot be modified if
DCellHSDPAEnabled parameter is already enabled.
940
WBTS MUST NOT BE CONNECTED TO COCO OR IPNB
OBJECT WHEN WBTS-NBAPCOMMMODE IS
MODIFIED.
WBTS must not be connected to COCO or IPNB object
when WBTS-NBAPCommMode is modified.
941
THE UNIT DOES NOT SUPPORT MULTIRATE PCM
SPEED
The unit does not support multirate PCM speed. This can
happen, for example, when the interface unit HW is
upgraded and the existing TDM or Ater resources are to be
reused for the new interface unit.
942
CONGESTION CAUSED BY OVERLOAD PROTECTION
IN RM2
Resource reservation was not allowed by overload
protection.
943
CER/CEA:ORIGIN REALM AND REMOTE REALM
CHECK ERROR.
CER/CEA:Origin realm and remote realm check error.
944
CER/CEA: APPLICATION ID CHECK ERROR.
CER/CEA: Application ID check error.
945
CER/CEA: REMOTE HOST CHECK ERROR.
CER/CEA: Remote HOST check error.
946
OPTIONAL AVP NOT FOUND IN DIAMETER MESSAGE.
Optional AVP not found in diameter message.
947
GIVEN IP SUBNET COVERS OR IS COVERED BY AN
EXISTING ONE
Given IP subnet covers or is covered by an existing one.
948
MULTI CELL OPERATION NOT AVAILABLE
Multi Cell Operation not available
949
96
AOIP TRANSCODER IN BSS FEATURE IS NOT IN USE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
AoIP Transcoder in BSS feature is not enabled in BSC.
Either feature licence is not valid or feature status is in
disabled state.
950
AOIP TRANSCODER IN MGW FEATURE IS NOT IN USE
AoIP Transcoder in MGW feature is not enabled in BSC.
Either feature licence is not valid or feature status is in
disabled state.
951
AOIP TRANSCODER IN MGW AND AOIP TRANSCODER
IN BSS FEATURE IS NOT IN USE
AoIP Transcoder in MGW and AoIP Transcoder in BSS
feature are not enabled in BSC. Either feature licence is
not valid or feature status is in disabled status.
952
IUO-NULLNRIFORCSPOOL MUST BE UNIQUE AMONG
IUO OBJECTS.
IUO-NULLNRIFORCSPOOL must be unique among IUO
objects.
953
IUO-NULLNRIFORPSPOOL MUST BE UNIQUE WITHIN
IUO OBJECTS.
IUO-NullNRIForPSPool must be unique within IUO
Objects.
954
CSDAP IS ALREADY ATTACHED TO BCF
CSDAP has already been attached to a BCF.
955
UNIDIRECTIONAL MODE OF OPERATION IS NOT
SUPPORTED FOR THIS INTERFACE UNIT TYPE
Use of the uni-directional mode of operation is not
supported for SET units of this interface unit type.
956
TCSM NUMBER GREATER THAN OR EQUAL TO
NUMBER OF QTJFIL FILE RECORDS
The TCSM number is greater than or equal to the number
of records in the QTJFIL file. If the program block is able
to, it returns the number of the file in question which can
be output by the MML program. The output of the file name
can be necessary, as well.
957
TCSM INFORMATION EXISTENT
SCFPRO program block generates this error code if the
etpc_pcm field of the QTJFIL file record is different from
initial value (0xFFFF) when adding TCSM information.
958
Issue: 30-0
TCSM INFORMATION NONEXISTENT
DN987378
97
Error messages
General Error Messages of System
SCFPRO program block generates this error code when
the etpc_pcm field of file QTJFIL record is initial
value(0xFFFF) when deleting, modifying or interrogating
TCSM information.
959
EXERCISE COMMAND IS NOT SUPPORTED IN UNIDIRECTIONAL MODE OF OPERATION
Exercise command is not supported in uni-directional
mode of operation.
960
CSDAP IS NOT FOUND
Circuit Switched Dynamic Abis Pool is not found.
961
CSDAP VALUE IS OUT OF RANGE
The configured Circuit Switched Dynamic Abis Pool value
is out of range.
962
CSDAP IS ATTACHED TO BCF AND CANNOT BE
DELETED
Circuit Switched Dynamic Abis Pool is attached to the BCF
and therefore CSDAP cannot be deleted.
963
PCU TRACK IS CONFIGURED FOR PACKET ABIS USE
PCU TRACK IS CONFIGURED FOR PACKET ABIS USE
964
PACKET ABIS OVER SATELLITE CAPACITY LICENCE
EXCEEDED
PACKET ABIS OVER SATELLITE CAPACITY LICENCE
EXCEEDED
965
PACKET ABIS OVER SATELLITE FEATURE IS NOT IN
USE IN BSC
Packet Abis over Satellite feature is not enabled in BSC.
Either feature licence is not valid or feature status is in
disabled state.
966
PACKET ABIS SECURITY FOR BTS CAPACITY
LICENCE EXCEEDED
PACKET ABIS SECURITY FOR BTS CAPACITY
LICENCE EXCEEDED
967
PACKET ABIS SECURITY FOR BTS FEATURE IS NOT
IN USE IN BSC
Packet Abis for security BTS feature is not enabled in
BSC. Either feature licence is not valid or feature status is
in disabled state.
98
DN987378
Issue: 30-0
General Error Messages of System
968
Error messages
THERE IS NO OPEN ABIS HDLC LINK CONFIGURED IN
BCF
THERE IS NO OPEN ABIS HDLC LINK CONFIGURED IN
BCF
969
ETP OBJECT NOT FOUND IN RNW DATABASE
ETP OBJECT NOT FOUND IN RNW DATABASE
970
OPTION PACKET ABIS OVER TDM IS NOT IN USE IN
BSC
Packet Abis over TDM feature is not enabled in BSC.
Either feature licence is not valid or feature status is in
disabled state.
971
OPTION PACKET ABIS OVER ETHERNET IS NOT IN
USE IN BSC
Packet Abis over Ethernet feature is not enabled in BSC.
Either feature licence is not valid or feature status is in
disabled state.
972
PACKET ABIS OVER ETHERNET CAPACITY LICENCE
EXCEEDED
PACKET ABIS OVER ETHERNET CAPACITY LICENCE
EXCEEDED
973
PACKET ABIS OVER TDM CAPACITY LICENCE
EXCEEDED
PACKET ABIS OVER TDM CAPACITY LICENCE
EXCEEDED
974
PACKET ABIS OVER TDM OR PACKET ABIS OVER
ETHERNET FEATURE IS NOT IN USE IN BSC
PACKET ABIS OVER TDM OR PACKET ABIS OVER
ETHERNET FEATURE IS NOT IN USE IN BSC
975
UPLINK COMMITTED BURST SIZE LOWER THAN
MAXIMUM TRANSFER UNIT
UPLINK COMMITTED BURST SIZE IS LOWER THAN
THE MAXIMUM TRANSFER UNIT
976
BU1 ABIS THROUGHPUT THRESHOLD LOWER THAN
BU2 ABIS THROUGHPUT THRESHOLD
BU1 ABIS THROUGHPUT THRESHOLD IS LOWER
THAN BU2 ABIS THROUGHPUT THRESHOLD
977
Issue: 30-0
PL2 THRESHOLD LOWER THAN PL1 THRESHOLD
DN987378
99
Error messages
General Error Messages of System
Packet loss in Ethernet Abis PL2 threshold is lower than
packet loss in Ethernet Abis PL1 threshold
978
HDLC LINK IS CONNECTED TO BCF
HDLC LINK IS CONNECTED TO BCF
979
GPRS ENABLED FOR BTS/SEG OF THE BCF
GPRS ENABLED FOR BTS/SEG OF THE BCF
980
PACKET ABIS NOT SUPPORT EGPRS DYNAMIC ABIS
POOL USE
EGPRS DAP attaching to TRX in the BCF which uses
packet Abis connection is not supported
981
WCEL-MIMOENABLED CAN BE ENABLED ONLY WHEN
WCEL-HSUPA2MSTTIENABLED IS ENABLED
WCEL-MIMOEnabled can be enabled only when WCELHSUPA2MSTTIEnabled is enabled.
982
HDLC LINK IS NOT CONNECTED TO THE BCF
HDLC LINK IS NOT CONNECTED TO THE BCF
983
HDLC ID ALREADY EXIST
HDLC ID ALREADY EXIST
984
HDLC NAME ALREADY EXIST
HDLC NAME ALREADY EXIST
985
PCU HAS SEGMENT CONFIGURATION
PCU HAS SEGMENT CONFIGURATION
986
PCU SOFTWARE IN SAME TRACK DOES NOT
SUPPORT PACKET ABIS FEATURE
PCU SOFTWARE IN SAME TRACK DOES NOT
SUPPORT PACKET ABIS FEATURE
987
WRONG ABIS CONNECTION TYPE
WRONG ABIS CONNECTION TYPE
988
HDLC LINK IS NOT CLOSED
HDLC LINK IS NOT CLOSED
989
MAXIMUM COUNT OF ABIS HDLC LINK TO BCF
EXCEEDED
MAXIMUM COUNT OF ABIS HDLC LINK TO BCF
EXCEEDED
100
DN987378
Issue: 30-0
General Error Messages of System
990
Error messages
PCU NOT CONNECTED TO SAME ETP AS THE ETP OF
THE BCF OR BCF IS IN LEGACY ABIS USE
PCU NOT CONNECTED TO SAME ETP AS THE ETP OF
THE BCF OR BCF IS IN LEGACY ABIS USE
991
ETP-PCU CONNECTION ALREADY EXIST
ETP-PCU CONNECTION ALREADY EXIST
992
ILLEGAL ECCCH CONFIGURATION
ECCCH configuration is illegal. ECCCHs must be
configured to TSLs 2, 4 and/or 6 of BCCH TRX (in
consecutive order) ECCCH is allowed to be configured
only to TRX, which has MBCCH channel. MBCCH has
only uncombined CCCH sub-channels. Any other
combination is not allowed.
993
BTS SW DOES NOT SUPPORT ECCCH FEATURE
BCF SW version does not support Extended CCCH
feature
994
ECCCH AND E-TRX OR S-TRX CANNOT BE USED
SIMULTANEOUSLY IN A BTS
ECCCH is not allowed to be configured in cell that has
unlocked E-TRX or S-TRX.
995
PACKET ABIS DELAY MEASUREMENT FEATURE IS
NOT IN USE IN BSC
Packet Abis Delay Measurement feature is not enabled in
BSC. Either feature licence is not valid or feature status is
disabled
996
TSLS OF HDLC LINKS ARE OVERLAPPING IN PCM.
TSLS OF HDLC LINKS ARE OVERLAPPING IN PCM.
997
ABIS HDLC LINK STATE IS INCORRECT.
ABIS HDLC LINK STATE IS INCORRECT.
998
PCU NOT CONNECTED TO ETP OF THE BCF.
PCU NOT CONNECTED TO ETP OF THE BCF.
999
MAXIMUM COUNT OF PCU TO ETP EXCEEDED.
MAXIMUM COUNT OF PCU TO ETP EXCEEDED.
1000
ETP-PCU CONNECTION DOES NOT EXIST IN RNW
DATABASE.
ETP-PCU CONNECTION DOES NOT EXIST IN RNW
DATABASE.
Issue: 30-0
DN987378
101
Error messages
General Error Messages of System
1001
DATABASE ERROR WHEN EXECUTE SQL UPDATE
STATEMENT
DATABASE ERROR WHEN EXECUTE SQL UPDATE
STATEMENT
1002
APP650 HEARTBEAT SUPERVISION FAILURE
APP650 heartbeat supervision failure.
1003
UNABLE TO DISPLAY MEASUREMENT DATA.
MEASUREMENT IS NOT ACTIVE
The measurement has not been activated, i.e. there is no
ongoing measurement.
1004
UNABLE TO DISPLAY MEASUREMENT DATA. READING
MEASUREMENT FILE FAILED.
Reading the measurement file failed. The file is missing or
the content of the file is not valid.
1005
BCF CSDAP IS ALREADY USED
BCF ALREADY HAS ANOTHER ATTACHED CSDAP IN
INDEX
1006
CSDAP IS ALREADY DETACHED FROM BCF
CSDAP IS ALREADY DETACHED FROM BCF
1007
OSC RX Quality FEATURE IS NOT IN USE IN BSC
OSC RX Quality measurement (OSC_RXQUAL) feature
cannot be used because there is no licence installed in
BSC (Base Station Controller) or the licence has expired or
the licence is in wrong state.
1008
TOO MANY CCCHE CHANNELS UNDER ANTENNA
HOPPING ENABLED BTS
ECCCH is allowed to be configured only to TSL 2 if cell
has Antenna hopping enabled.
1009
MAC ADDRESS IS ILLEGAL IN ILLLIB
MAC address is illegal in ILLLIB.
1010
IP POOL IS NOT VALID IN ILLLIB
IP pool is not valid in ILLLIB.
1011
THERE ARE NO AVAILABLE IP ADDRESSES TO
ASSIGN VIA DHCP
There are no available IP addresses to assign via DHCP.
1012
102
DEVICE NOT FOUND DURING SEARCH IN ILLLIB
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Device is not found during search in ILLLIB.
1013
SEARCH KEY INVALID FOR DEVICE SEARCH IN ILLLIB
Search key is invalid for device search in ILLLIB.
1014
IP address is not valid in ILLLIB
IP address is not valid in ILLLIB
1015
DEFAULT LEASE TIME NOT DEFINED FOR DHCP IN
ILLLIB
Default lease time is not defined for DHCP in ILLLIB.
1016
BTS SW DOES NOT SUPPORT EBCCH FEATURE
BCF SW version does not support Extended BCCH
feature.
1017
WCEL-MIMOENABLED CAN BE ENABLED ONLY WHEN
WCEL-DCELLHSDPAENABLED IS DISABLED IN ALL
CELLS UNDER WBTS
WCEL-MIMOEnabled can be enabled only when WCELDCellHSDPAEnabled is disabled in all cells under WBTS.
1018
DSP RESOURCE REQUEST THAT WAS IN RM3 QUEUE
WAS REQUESTED TO BE CANCELLED
DSP resource request that was in RM3 queue was
requested to be cancelled.
1019
PACKET ABIS GPRS BCFS IN MULTIBCF
CONFIGURATION ARE IN DIFFERENT ETPS
BCFs in MultiBCF configuration sharing a GPRS enabled
segment has to be configured to same the ETP.
1020
ABIS CONNECTION TYPE CONFLICT IN PCUS OR PCU
TRACK OF THE PSE
ABIS CONNECTION TYPE CONFLICT IN PCUS OR PCU
TRACK OF THE PSE
1021
PACKET BASED TRANSPORT NOT SUPPORT THIS
OPERATION
Intended operation is not supported because of packetbased transport is defined on Abis intreface
1022
PACKET TRS E1/T1 FEATURE IS NOT IN USE
Packet TRS E1/T1 feature is not in use in BSC. Licence is
missing or feature state is not ON.
1023
Issue: 30-0
PACKET TRS E1T1 FEATURE CAPACITY IS EXCEEDED
DN987378
103
Error messages
General Error Messages of System
Packet TRS E1/T1 feature capacity is exceeded. Increase
licence capacity or change Packet TRS E1/T1 usage
parameter to value 0.
1024
HDLC OBJECT NOT FOUND IN RNW DATABASE
HDLC OBJECT NOT FOUND IN RNW DATABASE
1025
ABIS CONNECTION TYPE CONFLICT IN GPRS
ENABLED MULTIBCF CONFIGURATION
ABIS CONNECTION TYPE CONFLICT IN GPRS
ENABLED MULTIBCF CONFIGURATION
1026
PACKET ABIS SYNCHRONOUS ETHERNET FEATURE
IS NOT IN USE IN BSC
PACKET ABIS SYNCHRONOUS ETHERNET FEATURE
IS NOT IN USE IN BSC.
1027
ETP ID ALREADY EXIST IN RNW DB
ETP ID ALREADY EXIST IN RNW DB
1028
ETP HAS BCF CONFIGURED
ETP HAS BCF CONFIGURED
1029
ETP HAS PCU CONFIGURED
ETP HAS PCU CONFIGURED
1030
MAXIMUM COUNT OF BCF TO ETP EXCEEDED
MAXIMUM COUNT OF BCF TO ETP EXCEEDED
1031
ABIS HDLC LINK USED IN OTHER BCF
ABIS HDLC LINK USED IN OTHER BCF
1032
ETP NOT UPDATED
ETP NOT UPDATED
1033
BCF HAS CSDAP CONFIGURED
BCF HAS CSDAP CONFIGURED
1034
WRONG ETP TYPE
WRONG ETP TYPE
1035
DETACH OPERATION NOT ALLOWED IN BCF
CREATION
CSDAP detach operation is not possible in BCF creation.
104
DN987378
Issue: 30-0
General Error Messages of System
1036
Error messages
DXA HAS NO CONNECTION TO BACKEND DATABASE,
TRANSACTION FAILED
The DXA cannot connect to the ONE-NDS.
1037
SUBSCRIBER DOES NOT BELONG TO DATALESS,
TRANSACTION FAILED
Not a Dataless subscriber
1038
WCEL-HSPAQOSENABLED CAN BE SET TO
CS_VOICE_C ONLY WHEN RNFC-FRLCENABLED IS
SET TO ENABLED
WCEL- HSPAQoSEnabled can be set to cs_voice_c only
when RNFC-FRLCEnabled is set to Enabled
1039
EVC CAN NOT BE DELETED AS IT IS BOUND WITH
SUBNET
EVC CAN NOT BE DELETED AS IT IS BOUND WITH
SUBNET
1040
BU2 ABIS THROUGHPUT THRESHOLD LOWER THAN
BU1 ABIS THROUGHPUT THRESHOLD
BU2 ABIS THROUGHPUT THRESHOLD LOWER THAN
BU1 ABIS THROUGHPUT THRESHOLD
1041
HDLC NAME CONTAINS INVALID CHARACTERS
HDLC NAME CONTAINS INVALID CHARACTERS
1042
BIT SYNCHRONOUS MAPPING TO TRIBUTARY UNIT IS
NOT SUPPORTED FOR SET UNITS OF THIS
INTERFACE UNIT TYPE
Bit synchronous mapping to tributary unit is not supported
for SET units of this interface unit type.
1043
DISCONNECT ETP NOT POSSIBLE, DELETE ETS2
WITH THE SAME PCM'S FIRST
Disconnect ETP is not possible, delete related ETS2 first.
1044
IF WCEL-DCELLHSDPAENABLED IS SET TO 1, WCELHSPDSCHCODESET MUST BE SET TO HSDPA 15
CODES
If WCEL-DCellHSDPAEnabled is set to 1, WCELHSPDSCHCodeset must be set to HSDPA 15 codes.
1045
ADJI-LAC IS NOT MODIFIABLE IF TARGET CELL IS
UNDER ITS OWN RNC.
ADJI-LAC is not modifiable if target cell is under its own
RNC.
Issue: 30-0
DN987378
105
Error messages
General Error Messages of System
1046
ADJI-RAC IS NOT MODIFIABLE IF TARGET CELL IS
UNDER OWN RNC
ADJI-RAC is not modifiable if target cell is under own
RNC.
1047
ADJI-ADJISCRCODE IS NOT MODIFIABLE IF TARGET
CELL IS UNDER OWN RNC
ADJI-AdjiScrCode is not modifiable if target cell is under
own RNC.
1048
ADJI-ADJITXPWRDPCH IS NOT MODIFIABLE IF
TARGET CELL IS UNDER OWN RNC
ADJI-AdjiTxPwrDPCH is not modifiable if target cell is
under own RNC.
1049
ADJI-ADJITXPWRRACH IS NOT MODIFIABLE IF
TARGET CELL IS UNDER OWN RNC
ADJI-AdjiTxPwrRACH is not modifiable if target cell is
under own RNC.
1050
ADJI-ADJICPICHTXPWR IS NOT MODIFIABLE IF
TARGET CELL IS UNDER OWN RNC
ADJI-AdjiCPICHTxPwr is not modifiable if target cell is
under own RNC.
1051
RNC-OPERATOR PLMN IS NOT FOUND IN
CONFIGURED IU OBJECT LIST
RNC-OPERATOR PLMN is not found in configured IU
object list.
1052
VALUE OF FMCS-HHOECNOTHRESHOLD MUST BE
LOWER THAN VALUE OF FMCS-HHOECNOCANCEL
The value of FMCS-HHoEcNoThreshold must be lower
than the value of FMCS-HhoEcNoCancel.
1053
SDH CONFIGURATION IS NOT ALLOWED BECAUSE
THE DESTINATION SET BELONGS TO THE LETGR
SDH configuration is not allowed because the destination
SET belongs to the LETGR.
1054
RNRLC-AMRLCRELATTXWINDOWRATE1 SHOULD BE
SMALLER THAN OR EQUAL TO RNRLCAMRLCRELATTXWINDOWRATE2
The RNRLC-AMRLCRelatTXWindowRate1 should be
smaller than or equal to RNRLCAMRLCRelatTXWindowRate2
106
DN987378
Issue: 30-0
General Error Messages of System
1055
Error messages
RNRLC-AMRLCRELATTXWINDOWRATE2 SHOULD BE
SMALLER THAN OR EQUAL TO RNRLCAMRLCRELATTXWINDOWRATE3
The RNRLC-AMRLCRelatTXWindowRate2 should be
smaller than or equal to RNRLCAMRLCRelatTXWindowRate3
1056
RNRLC-AMRLCRELATTXWINDOWRATE3 SHOULD BE
SMALLER THAN OR EQUAL TO RNRLCAMRLCRELATTXWINDOWRATE4
The RNRLC-AMRLCRelatTXWindowRate3 should be
smaller than or equal to RNRLCAMRLCRelatTXWindowRate4
1057
RNRLC-AMRLCRELATTXWINDOWRATE4 SHOULD BE
SMALLER THAN OR EQUAL TO RNRLCAMRLCRELATTXWINDOWRATE5
The RNRLC-AMRLCRelatTXWindowRate4 should be
smaller than or equal to RNRLCAMRLCRelatTXWindowRate5
1058
RNRLC-AMRLCRELATTXWINDOWRATE5 SHOULD BE
SMALLER THAN OR EQUAL TO RNRLCAMRLCRELATTXWINDOWRATE6
The RNRLC-AMRLCRelatTXWindowRate5 should be
smaller than or equal to RNRLCAMRLCRelatTXWindowRate6
1059
RNRLC-AMRLCRELATTXWINDOWRATE6 SHOULD BE
SMALLER THAN OR EQUAL TO RNRLCAMRLCRELATTXWINDOWRATE7
The RNRLC-AMRLCRelatTXWindowRate6 should be
smaller than or equal to RNRLCAMRLCRelatTXWindowRate7
1060
RNRLC-AMRLCRELATTXWINDOWRATE7 SHOULD BE
SMALLER THAN OR EQUAL TO RNRLCAMRLCRELATTXWINDOWRATE8
The RNRLC-AMRLCRelatTXWindowRate7 should be
smaller than or equal to RNRLCAMRLCRelatTXWindowRate8
1061
WCEL-PTXCELLMAX SHOULD BE SMALLER THAN
WCEL-MAXDLPOWERCAPABILITY
WCEL-PtxCellMax should be smaller than WCELMaxDLPowerCapability.
1062
Issue: 30-0
CONFLICTING EXTERNAL USER IDS
DN987378
107
Error messages
General Error Messages of System
Conflicting external user IDs
1063
ERROR OCCURRED DURING TRANSACTION IN
EXTERNAL DATABASE
Error occurred during transaction in external database.
1064
UNAUTHORIZED COMMAND CLASS
Users are not authorized to use the requested command
class.
1065
UNAUTHORIZED COMMAND GROUP
Users are not authorized to use the requested command
group.
1066
IF THE INTRA-FREQUENCY NEIGHBOR CELL IS
CONTROLLED BY THE LOCAL RNC, ADJS-ADJSTXDIV
MUST BE SET TO ZERO.
ADJS-AdjsTxDiv must be set to zero if the intra-frequency
neighbor cell is controlled by the local RNC.
1067
IF THE INTER-FREQUENCY NEIGHBOR CELL IS
CONTROLLED BY THE LOCAL RNC, ADJI-ADJITXDIV
MUST BE SET TO ZERO
ADJI-AdjiTxDiv must be set to zero if the inter-frequency
neighbor cell is controlled by the local RNC.
1068
IF THE CELL IS CONTROLLED BY THE LOCAL RNC,
ADJD -ADJDTXDIV CAN NOT BE MODIFIED
ADJD -AdjdTxDiv cannot be modified if the cell is
controlled by the local RNC.
1069
IF WBTS-NBAPCOMMMODE IS SET TO NB/RSXXX,
WCEL-AICHTRATIME MUST BE SET TO ONE
WCEL-AICHTraTime must be set to one, if WBTSNBAPCommMode is set to NB/RSxxx.
1070
WCEL-CELLRANGE MUST BE DEFINED IF WBTSNBAPCOMMMODE IS SET TO ULTRASITE BTS /
FLEXIBTS / PICOBTS.
WCEL-CellRange must be defined if WBTSNBAPCommMode is set to UltraSite BTS / FlexiBTS /
PicoBTS.
1071
ETPSIG-C CONNECTION CAN NOT BE CREATED
BEFORE ETPSIG-M
ETPSIG-C connection cannot be created before ETPSIGM
108
DN987378
Issue: 30-0
General Error Messages of System
1072
Error messages
ETPSIG-M CONNECTION CAN NOT BE DELETED
BEFORE ETPSIG-C
ETPSIG-M connection cannot be deleted before ETPSIGC
1073
PENDING ETPSIG CONFIGURATION DELIVERY TO
ETP UNIT
Pending ETPSIG configuration delivery to ETP unit
1074
THE NUMBER OF LTECELLRESELECTION ENABLED
WCELS EXCEEDS THE LICENSE CELL RESELECTION
TO LTE CAPACITY LIMIT
The number of LTECellReselection enabled WCELs
exceeds the license Cell Reselection to LTE capacity limit
1075
THE NUMBER OF INCOMINGLTEISHO ENABLED
WCELS EXCEEDS THE LICENSE ISHO FROM LTE
CAPACITY LIMIT
The number of IncomingLTEISHO enabled WCELs
exceeds the license ISHO from LTE capacity limit
1076
WCEL-LTECELLRESELECTION CAN BE ENABLED
ONLY WHEN CELL RESELECTION TO LTE LICENSE IS
ON
WCEL-LTECellReselection can be enabled only when Cell
Reselection to LTE license is ON
1077
WCEL-INCOMINGLTEISHO CAN BE ENABLED ONLY
WHEN ISHO FROM LTE LICENSE IS ON
WCEL-IncomingLTEISHO can be enabled only when ISHO
from LTE license is ON
1078
IF MOCN/MORAN IS ON THEN UNIQUE PLMN ID MUST
BE DEFINED FOR EACH CN.
If MOCN/MORAN is on then unique PLMN id must be
defined for each CN.
1079
BCF PARAM AND CSDAP ID CANNOT BE MODIFIED
TOGETHER
Bcf parameters cannot be modified together with an
attach/detach operation.
1080
ATTACH AND DETACH CANNOT BE DONE TOGETHER
Attach and detach operations are not allowed to be done
together.
1081
Issue: 30-0
HSUPA 16QAM NOT AVAILABLE
DN987378
109
Error messages
General Error Messages of System
For RAN 1645, HSUPA 16QAM feature
1082
BYTESYNCHRONOUS MAPPING TO TRIBUTARY UNIT
IS NOT SUPPORTED FOR SET UNITS OF THIS
INTERFACE UNIT TYPE
Bytesynchronous mapping to tributary unit is not supported
for SET units of this interface unit type.
1083
NE RESET NOT POSSIBLE AS NE IS BUSY
NE is busy due to which reset is not possible.
1084
NE RESET REQUEST NOT VALID
NE reset request is not valid.
1085
NE NOT CONNECTED THROUGH BTS O&M
INTERFACE
NE is not connected through BTS O&M interface.
1086
UNIT IS IN SWO
Unit is in SWO.
1087
ATM CONNECTION IN OPERATION
JIG is operating the ATM connection.
1088
SP APP MXU NOT READY
SP APP MXU is not ready.
1089
APP MXU IN TE STATE
APP MXU is in TE state.
1090
UNIT NOT FOUND IN JIG
Unit is not found in JIG.
1091
ALP UNIT NOT FOUND IN JIG
ALP unit is not found in JIG.
1092
JIG\'S OWN HALF CROSS CONNECTION CREATION
TASK NOT DONE YET
JIG\'s own half cross connection creation task is not done
yet.
1093
JIG\'S VP REPORTING TASK NOT DONE YET
JIG\'s VP reporting task is not done yet.
1094
UNIT IS BEING REMOVED IN JIG
Unit is being removed in JIG.
110
DN987378
Issue: 30-0
General Error Messages of System
1095
Error messages
UNIT NEEDS ATM RECONFIG IN JIG
Unit needs ATM reconfig in JIG.
1096
MXU CLUSTER IS RESTARTING
MXU cluster is restarting.
1097
MXU CLUSTER IN WARMING
MXU cluster is in warming.
1098
FIRST CHANNEL OF THE UNIT NOT CREATED YET
1st channel of the unit is not created yet.
1099
JIG ALLOCATES INTERNAL ATM RES FAILED
JIG allocates internal ATM res failed.
1100
CONN NOT FOUND IN JIG
Conn is not found in JIG.
1101
No free hands of JIG
No free hands of JIG
1102
DIAMETER DESTINATION ALREADY EXISTS.
Diameter destination already exists.
1103
DIAMETER DESTINATION DOES NOT EXIST.
Diameter destination does not exist.
1104
DIAMETER TRANSFER PATH DOES NOT EXIST.
Diameter transfer path does not exist.
1105
DIAMETER TRANSFER PATH ALREADY EXISTS.
Diameter transfer path already exists.
1106
DIAMETER TRANSFER PATH IP ALREADY EXISTS.
Diameter transfer path IP already exists.
1107
IUIP NOT FOUND
IUIP NOT FOUND
1108
IUO NOT FOUND
IUO NOT FOUND
1109
CBC NOT FOUND
CBC NOT FOUND
Issue: 30-0
DN987378
111
Error messages
General Error Messages of System
1110
IUIP ALREADY CREATED
IUIP ALREADY CREATED
1111
IUIP COLLECTION FULL
IUIP COLLECTION FULL
1112
IUO ALREADY CREATED
IUO ALREADY CREATED
1113
IUO COLLECTION FULL
IUO COLLECTION FULL
1114
CBC ALREADY CREATED
CBC ALREADY CREATED
1115
CBC COLLECTION FULL
CBC COLLECTION FULL
1116
THIS PROTOCOL IS NOT SUPPORTED FOR SET UNITS
OF THIS INTERFACE UNIT TYPE.
This protocol is not supported for SET units of this
interface unit type.
1117
INITIALIZATION OF APP3K FAILED
Initialization of APP3k has failed.
1118
CABINET INDEX IS INVALID
Used for Ui5 MGW
1119
SHELF INDEX IS INVALID
Used for Ui5 MGW to create SET
1120
SLOT INDEX IS INVALID
Used for Ui5 MGW to create SET
1121
AMC SLOT INDEX IS INVALID
Used for Ui5 MGW to create SET
1122
UNIT ADDRESS IS OUT OF RANGE
Unit address is out of range.
1123
MAXIMUM AMOUNT OF AAL2 PATHS HAS ALREADY
BEEN CREATED TO SYSTEM
The maximum amount of AAL2 paths has already been
created to system.
112
DN987378
Issue: 30-0
General Error Messages of System
1124
Error messages
EXTENDED BCCH FEATURE IS NOT IN USE IN BSC
Extended BCCH feature is not enabled in BSC. Licence
state is not ON.
1125
NO SUITABLE SERVING PCU FROM ETP OF THE BCF
NO SUITABLE SERVING PCU FROM ETP OF THE BCF
1126
UNKNOWN PARAMETER FOR CBCI IN RNW PLAN
XML file processing program block (PABROS, RNC OMU)
has detected an unknown CBCI object parameter (or
incorrectly placed) in the RNW Plan file.
1127
UNKNOWN PARAMETER FOR IUO IN RNW PLAN
XML file processing program block (PABROS, RNC OMU)
has detected an unknown IUO object parameter (or
incorrecly placed) in the RNW Plan file.
1128
ETP variant is not ETPE. SyncE is supported on ETPE
only.
ETP VARIANT IS NOT ETPE
1129
SFP IS NOT OPTICAL IN ETP
SFP is not optical.
1130
MIMO CAN BE SET AS ENABLED WITH DCELLHSDPA
IF BOTH HSUPA AND FDPCH ARE SET ENABLED FOR
THIS CELL
MIMOEnabled can be set as enabled with
DCellHSDPAEnbaled if both HSUPAEnabled and
FDPCHEnabled are set as enabled.
1131
WBTS IPBASEDROUTEIDIUB2 MUST BE UNIQUE FOR
ALL WBTS
WBTS IPBasedRouteIdIub2 must be unique for all WBTS.
1132
WBTS IPBASEDROUTEIDIUB MUST BE DEFINED
WHEN WBTS IPBASEDROUTEIDIUB2 HAS SOME
DEFINED VALUE.
WBTS IPBasedRouteIdIub must be defined when WBTS
IPBasedRouteIdIub2 has some defined value.
1133
IUR-DELAYTHRESHOLDMAXIUR MUST BE GREATER
THAN IUR-DELAYTHRESHOLDMIDIUR
IUR-DelayThresholdMaxIur must be greater than IURDelayThresholdMidIur.
Issue: 30-0
DN987378
113
Error messages
General Error Messages of System
1134
IUR-DELAYTHRESHOLDMIDIUR MUST BE GREATER
THAN IUR-DELAYTHRESHOLDMINIUR
IUR-DelayThresholdMaxIur must be greater than IURDelayThresholdMidIur
1135
UNKNOWN PARAMETER FOR IUIP IN RNW PLAN
XML file processing program block (PABROS, RNC OMU)
has detected an unknown IUIP object parameter (or
incorrecly placed) in the RNW Plan file.
1136
OSC CANNOT OPERATE WITHOUT CSDAP OR
PACKET ABIS
OSC (Orthogonal Sub Channel) feature cannot operate
without Circuit Switched Dynamic Abis Pool or Packet Abis
in use.
1137
RNW MULTI CELL OPERATION NOT AVAILABLE AT BTS
RNW Multi Cell operation not available at BTS
1138
WCEL-DCELLHSDPAFMCSID MUST HAVE DEFINED
VALUE IF WCEL-DCELLHSDPAENABLED IS SET TO
ENABLED
WCEL-DCellHSDPAFmcsId must have defined value if
WCEL-DCellHSDPAEnabled is set to enabled.
1139
MIMOENABLED CANNOT BE SET AS ENABLED WITH
DCELLHSDPAENABLED IF HSUPAENABLED SET AS
DISABLED
MIMOEnabled cannot be set as enabled with
DCellHSDPAEnabled if HSUPAEnabled set as disabled.
1140
SFTP SERVER IS ACTIVATED
SFTP Server is still activated. Disable SFTP Server before
disabling SSH Server.
1141
PARAMETER GPRIO AND WPRIO CANNOT HAVE THE
SAME VALUE
GSM priority is defined as same as WCDMA priority for the
segment.
1142
TOO MANY PIC ENABLED CELLS IN PIC POOL
PIC-activated cells in PIC Pool exceed maximum limit.
1143
PIC POOL IS NOT PIC-CAPABLE
PIC pool is not PIC-capable.
1144
114
PACKET ABIS BCF GROUP ID NOT IN USE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
PACKET ABIS BCF GROUP ID NOT IN USE
1145
NO HUB BCF FOR PACKET ABIS BCF GROUP ID
HUB BCF NOT DEFINED FOR THE PACKET ABIS BCF
GROUP ID
1146
BCF NOT LOCKED TO PROCEED WITH MODIFICATION
BCF NOT LOCKED TO PROCEED WITH MODIFICATION
1147
PACKET ABIS BCF GROUP ID BELONGS TO
DIFFERENT CONNECTION TYPE
PACKET ABIS BCF GROUP ID BELONGS TO
DIFFERENT CONNECTION TYPE.
1148
LOCAL SWITCHING FEATURE IS NOT IN USE IN BSC
Local Switching For Packet Abis feature is not enabled in
BSC. Either feature licence is not valid or feature status is
in disabled.
1149
TERMINAL BCF(S) EXISTS UNDER THE HUB BCF
Terminal BCF(s) exists under the HUB BCF.
1150
LOCAL SWITCHING CAPACITY LICENCE EXCEEDED
LOCAL SWITCHING CAPACITY LICENCE EXCEEDED
1151
MAXIMUM AMOUNT OF BCF IN SAME PACKET ABIS
BCF GROUP EXCEEDED
MAXIMUM AMOUNT OF BCFS IN SAME PACKET ABIS
BCF GROUP EXCEEDED
1152
PACKET ABIS BCF GROUP ID ALREADY IN USE
PACKET ABIS BCF GROUP ID ALREADY IN USE
1153
RNFC-RABDRAENABLED CAN BE SET ENABLED ONLY
WHEN RNFCHSDPADYNAMICRESOURCEALLOCATION IS SET
ENABLED
RNFC-RABDRAEnabled can be set enabled only when
RNFC-HSDPADynamicResourceAllocation is set enabled
1154
HMS OPERATION FAILED WHEN PIU POWER OFF.
WHEN PIU IS POWER OFF, HMS RELATED HW
OPERATION WILL BE FAILED. PIU HW STAY IN
UNSTABLE STATE.
1155
Issue: 30-0
CELL BROADCAST SCHEDULE PERIOD CANNOT BE
CHANGED
DN987378
115
Error messages
General Error Messages of System
Cell broadcast schedule period cannot be changed.
1156
THIS PIU DOES NOT SUPPORT COLD RESET.
THIS PIU DOES NOT SUPPORT COLD RESET. IF COLD
RESET TARGET IS THIS PIU, HMS WILL ABORT THIS
OPERATION.
1157
CACHE OVERFLOW FULL
Cache overflow full.
1158
SUBSCRIBER NOT FOUND IN HASH TABLE
Subscriber not found in hash table.
1159
DUPLICATE ID FOUND IN HASH TABLE
Duplicate id found in hash table.
1160
INVALID IMSI
Invalid imsi
1161
ET NOT EXISTENT
ET does not exist.
1162
SET NOT EXISTENT
SET does not exist.
1163
LETGR not existent
LETGR does not exist.
1164
PEER SET NOT EXISTENT
Peer SET does not exist.
1165
SD THRESHOLD CANNOT BE BIGGER THAN SF
THRESHOLD
SD threshold is bigger than SF threshold.
1166
LINE_LOOPBACK AND DIAGN_LOOPBACK CANNOT
BE BOTH ON
Both loopback are on.
1167
PROTOCOL AND MAPPING MODE NOT MATCHED
Protocol and mapping mode not matched.
1168
ADMINISTRATIVE STATE ALREADY EXISTS
Administrative state already exists.
1169
116
PARENT UNIT LOCKED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Parent unit is locked.
1170
UNIT LOCKED AS PARENT IS LOCKED
Self is unlocked, but parent unit is locked.
1171
NPELIB FLOW TABLE FULL
NPELIB: flow table full
1172
NPELIB DID TABLE FULL
NPELIB: DID table full
1173
NPELIB QUEUE TABLE FULL
NPELIB: queue table full
1174
NPELIB LOGICAL PORT TABLE FULL
NPELIB: logical port table full
1175
NPELIB PORT MANAGER TABLE FULL
NPELIB: port manager table full
1176
NPELIB INVALID FLOW ID
NPELIB invalid flow id
1177
NPELIB INVALID DID
NPELIB invalid DID
1178
NPELIB INVALID QUEUE ID
NPELIB invalid queue ID
1179
NPELIB INVALID LOGICAL PORT ID
NPELIB invalid logical port ID
1180
NPELIB INVALID PORT MANAGER ID
NPELIB invalid port manager ID
1181
CREATION OF PORT MANAGER TO RSP IN APP
FAILED
Creation of port manager to RSP in APP failed.
1182
DELETING OF LOGICAL PORT FROM RSP IN APP
FAILED
Deleting of logical port from RSP in APP failed.
1183
CREATION OF LOGICAL PORT TO RSP IN APP FAILED
Creation of logical port to RSP in APP failed.
Issue: 30-0
DN987378
117
Error messages
General Error Messages of System
1184
CREATION OF A QUEUE TO RSP IN APP FAILED
Creation of a queue to RSP in APP failed.
1185
CREATION OF A DESTINATION ID TO RSP IN APP
FAILED
Creation of a destination ID to RSP in APP failed.
1186
CREATION OF A FLOW IN APP FAILED
Creation of a flow in APP failed.
1187
DELETING OF PORT MANAGER FROM RSP IN APP
FAILED
Deleting of port manager from RSP in APP failed.
1188
DELETING OF A QUEUE FROM RSP IN APP FAILED
Deleting of a queue from RSP in APP failed.
1189
DELETING OF A DID FROM RSP IN APP FAILED
Deleting of a DID from RSP in APP failed.
1190
DELETING A FLOW FROM APP FAILED
Deleting a flow from APP failed.
1191
ATTEMPT WAS MADE TO CREATE LOGICAL PORT IN
APP WITH ID THAT ALREADY EXISTS
Attempt was made to create logical port in APP with ID
that already exists.
1192
ATTEMPT WAS MADE TO CREATE PORT MANAGER IN
APP USING ID THAT ALREADY EXISTS
Attempt was made to create port manager in APP using ID
that already exists.
1193
ATTEMPT WAS MADE TO CREATE QUEUE IN APP
USING ID THAT ALREADY EXISTS
Attempt was made to create queue in APP using ID that
already exists.
1194
ATTEMPT WAS MADE TO CREATE DESTINATION ID IN
APP USING ID THAT ALREADY EXISTS
Attempt was made to create destination ID in APP using ID
that already exists.
1195
118
INVALID STARTING ET INDEX, VALID STARTING ET
INDEXES ARE 1260, 1344, 1428... (WITH STEPS OF 84)
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Invalid starting ET index. Valid starting ET indexes are
1260, 1344, 1428... (with steps of 84).
1196
PRXMAXORIGTARGETBTS VALUE MUST BE GREATER
THAN OR EQUAL TO VALUE OF PRXMAXTARGETBTS
PrxMaxOrigTargetBTS value must be greater than or equal
to the value of PrxMaxTargetBTS.
1197
BTSPLUS CANNOT BE MASTER IN SYNCH CHAIN
BTSPlus cannot be configured as master clock BCF in
synchronization chain.
1198
ONLY FLEXI BTSS ARE ALLOWED IN SYNCH CHAIN
WITH BTSPLUS
Only FlexiEDGE and Flexi Multiradio site types are allowed
in the same synch chain with BTSplus.
1199
EXTENDED CELL AND DUAL BAND ARE NOT
ALLOWED SIMULTANEOUSLY IN THE SAME SEGMENT
WITH BTSPLUS
Extended cell or super extended cell features cannot be
used simultaneously in the same segment with BTSplus.
1200
SINGLE BAND CONCENTRIC CELL IS NOT ALLOWED
IN BTSPLUS IN MULTIBCF
Single band concentric cell is not allowed when BTSplus
and Flexi BTS are configured in the same segment. That
is, BTSplus cannot have inner TRXs.
1201
BTS SOFTWARE DOES NOT SUPPORT BTSPLUS COSITING
BTS software version does not support multi BCF
configuration.
1202
OSC and EGPRS are NOT Concurrently Supported in
Flexi Edge EPSILON TRXs
OSC and EGPRS are NOT concurrently supported in Flexi
Edge EPSILON TRXs.
1203
EMICRO IS NOT ALLOWED IN SYNCHRONIZATION
CHAIN
BTSplus eMicro does not support synchronization chain.
1204
DPTRX IS NOT ALLOWED IN THE SAME SEGMENT
WITH BTSPLUS
DPTRXs cannot be used in the same segment with
BTSplus.
Issue: 30-0
DN987378
119
Error messages
General Error Messages of System
1205
ONLY FLEXI BTSS ARE ALLOWED IN SEGMENT WITH
BTSPLUS
Only FlexiEDGE and Flexi Multiradio site types are allowed
in the same segment with BTSplus.
1206
EMICRO IS NOT ALLOWED IN MULTI BCF
CONFIGURATION
BTSplus eMicro does not support Multi BCF configuration.
1207
BTSPLUS CANNOT BE IN SEGMENT WHERE PCU1 IS
USED
PCU2 is required if BTSplus is configured to segment.
1208
ALL HOPPING ENABLED BTSPLUS BTS OBJECTS NOT
LOCKED
All hopping enabled BTSplus objects in the segment must
be locked when BCCH frequency is modified.
1209
EDAP IS CONNECTED TO BCF WHICH IS NOT LOCKED
BCF must be in locked state when PCM-TSL of EDAP is
modified.
1210
PMAX1/PMAX2 TOO HIGH IN SEGMENT WITH
BTSPLUS AND FLEXI BTS
The maximum value for PMAX1 and PMAX2 is 18dB in
multi BCF configuration with BTSplus and Flexi BTS.
1211
PORT NUMBERS OF INTERFACES ARE DIFFERENT
Port numbers of interfaces are different.
1212
ETP AND PCU FROM INCOMPATIBLE HW
ETP and PCU from incompatible HW. Connection between
McETP and PCU PIU is not allowed.
1213
TRXSIG, OMUSIG and BCF on incompatible HW
This error is raised if OMUSIG and BCF or TRXSIG and
BCF are not on the same HW.
1214
MCPCU HAS CONFIGURATION
The mcPCU has RNW/Gb configuration.
1215
PCU SWITCHOVER
PCU switchover happens when PSE reallocation is going
on.
1216
120
PARENT UNIT IS SHUTTING DOWN
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Parent unit is shutting down.
1217
PROTOCOL EXISTS TWO TIMES OR PROTOCOL
VALUE IS INVALID OR PROTOCOL VALUE DON'T
EXIST.
Protocol exists twice or protocol value is invalid or protocol
value does not exist.
1218
HTTPS PROTOCOL DIDN'T ACTIVATE IN FIFILE FILE.
The https protocol did not activate in FIFILE file.
1219
D-CHANNEL NUMBER OF ETPSIG-C FOR ETP PAIR
ARE NOT SAME
The D-channel number of ETPSIG-C for ETP pair should
be same.
1221
RNFC FLEXULRLCENABLED CAN BE ENABLED ONLY
WHEN RNFC FRLCENABLED IS ENABLED
RNFC FlexULRLCEnabled can be enabled only when
RNFC FRLCEnabled is enabled
1222
MAXIMUM COUNT FOR AAL2 1 CIDS HAS BEEN
REACHED IN THE AAL2 SWITCHING UNIT
Maximum count for AAL2 1 CIDs has been reached in the
AAL2 switching unit (e.g. it can be A2SP or NPS1(P) unit).
1223
IF DC-HSDPA IS ENABLED IN ANY CELL OF THE
SECTOR,MIMO MUST NOT BE ENABLED IN ANY
OTHER CELL THAN DC-HSDPA CELL.
IF DC-HSDPA IS ENABLED IN ANY CELL OF THE
SECTOR,MIMO MUST NOT BE ENABLED IN ANY
OTHER CELL THAN DC-HSDPA CELL WITH HSUPA
ENABLED.
1224
UPDATE THE CONFLICT IN EXTERNAL DATABASE
Update the conflict in external database
1225
IMSI BELONGS TO OTHER SUBSCRIBER
IMSI belongs to other subscriber.
1226
MSISDN BELONGS TO OTHER SUBSCRIBER
MSISDN belongs to other subscriber.
1227
HLR DATA ALREADY EXISTS FOR IMSI
HLR data already exists for IMSI
1228
Issue: 30-0
HLR DATA ALREADY EXISTS FOR MSISDN
DN987378
121
Error messages
General Error Messages of System
HLR data already exists for MSISDN.
1229
HLR DATA ALREADY EXISTS FOR UID
HLR data already exists for UID.
1230
AUC DATA ALREADY EXISTS FOR IMSI
AuC data already exists for IMSI.
1231
WCEL-PRXTARGETMAXORIG VALUE MUST BE
BIGGER THAN OR EQUAL TO WCEL-PRXTARGET
The WCEL-PrxTargetMaxOrig value must be bigger than
or equal to WCEL-PrxTarget.
1232
PARAMETER WCEL-HSPA128USERSPERCELL CAN
ONLY BE ENABLED IN WCEL IF WCELHSPA72USERSPERCELL IS ENABLED
Parameter WCEL-HSPA128UsersPerCell can only be
enabled in WCEL if WCEL-HSPA72USersPerCell is
enabled.
1233
PARAMETER WCEL-HSPA128USERSPERCELL CAN
ONLY BE ENABLED IN WCEL IF WCELHSUPAENABLED IS ENABLED
Parameter WCEL-HSPA128UsersPerCell can only be
enabled in WCEL if WCEL-HSUPAENABLED is enabled.
1234
WCEL- HSPA128USERSPERCELL CAN BE ENABLED
ONLY WHEN THE HSPA 128 USERS PER CELL
LICENSE IS ON
WCEL- HSPA128USERSPERCELL can be enabled only
when the HSPA 128 Users Per Cell license is On.
1235
THE HW OF BOTH UNITS ARE ACTIVE
The HW of both units are active.
1236
RECOVERY ACTION FOR HIERARCHICAL UNIT WAS
ONLY PARTLY EXECUTED
Recovery action for hierarchical unit was only partly
executed. E.g. some of the child units or parent unit was
not correctly handled.
1237
WCEL-HSUPA16QAMALLOWED CAN BE SET AS
ENABLED ONLY IF WCELMAXTOTALUPLINKSYMBOLRATE IS 5760 KBPS
WCEL-HSUPA16QAMAllowed can be set as enabled only
if WCEL-MaxTotalUplinkSymbolRate is 5760 kbps.
122
DN987378
Issue: 30-0
General Error Messages of System
1238
Error messages
LICENSE STATE OF HSUPA16QAM MUST BE ON FOR
CELL UNLOCKING WHEN WCELHSUPA16QAMALLOWED IS ENABLED
The license state of HSUPA16QAM must be on for cell
unlocking when WCEL-HSUPA16QAMAllowed is enabled.
1239
CS AND PS UDP MUX PORTS CAN NOT BE SAME
CS and PS UDP MUX ports for U-PLANE can not be the
same.
1240
THE NUMBER OF HSUPA 16 QAM USERS PER BTS
ENABLED BTS EXCEEDS THE CAPACITY LIMIT
The number of HSUPA 16 QAM users per bts enabled bts
exceeds the capacity limit.
1241
VCEL-HSUPAENABLED IS ENABLED, THEN VCELHSDPAENABLED MUST BE ENABLED.
If VCEL-HSUPAEnabled is enabled, then VCELHSDPAEnabled must be enabled.
1242
BCF HAS TO BE LOCKED SINCE BCF C/U PLANE IP
ADDRESS HAS BEEN CHANGED.
BCF HAS TO BE LOCKED SINCE BCF C/U PLANE IP
ADDRESS HAS BEEN CHANGED.
1243
WCELNUMBEREDCHRESERVEDSHOBRANCHADDITIONS
MUST BE LOWER THAN VALUE OF PARAMETER
WCEL-MAXNUMBEREDCHCELL
WCEL-NumberEDCHReservedSHOBranchAdditions must
be lower than the value of parameter WCELMaxNumberEDCHCell.
1244
WCELNUMBEREDCHRESERVEDSHOBRANCHADDITIONS
MUST BE LOWER THAN VALUE OF PARAMETER
WBTS-MAXNUMBEREDCHLCG
WCEL-NumberEDCHReservedSHOBranchAdditions must
be lower than the value of parameter WBTSMaxNumberEDCHLCG.
1245
ETP IS RESTARTING
Operation cannot be completed because ETP is restarting.
1246
PIU DOES NOT CONTAIN ADAPTER
PIU DOES NOT CONTAIN ADAPTER. ALL ADAPTER
OPERATIONS ARE ABORTED.
Issue: 30-0
DN987378
123
Error messages
General Error Messages of System
1247
INCORRECT COORDINATE OR CARTRIDGE NOT
CREATED
Cannot find cartridge in a specified location from
equipment database (EQUIPM).
1248
PTXTARGET CANNOT TAKE VALUES WHICH ARE
GREATER THAN THE VALUE OF PTXCELLMAX
PtxTarget cannot take values which are greater than the
value of PtxCellMax.
1249
IUR-DELAYTHRESHOLDMIDIUR MUST BE GREATER
THAN THE IUR-DELAYTHRESHOLDMINIUR
IUR-DelayThresholdMidIur must be greater than the IURDelayThresholdMinIur.
1250
REQUESTED CERM FUNCTIONALITY IS NOT
ACTIVATED AND THUS REQUEST CANNOT BE
PROCESSED
Controller Entity Resource Management (CERM) main
functionality (or particular sub-feature) is not activated.
1251
IO DEVICE FBAN HAS BEEN SET. DEVICE STATE NOT
CHANGEABLE.
When IO area FBAN flag is set to device, for example
WDU, device state cannot be changed by the system or
operator.
1252
LOCAL MULTIPLE AAL2 CHANNELS RESET BY
SYSTEM
Local multiple aal2 channels reset by system.
1253
LOCAL SINGLE AAL2 CHANNEL RESET BY SYSTEM
Local single aal2 channel reset by system.
1254
LOCAL AAL2 RESET BY USER
Local aal2 reset by user.
1255
LOCAL AAL2 LINK RESET BY SYSTEM
Local aal2 link reset by system.
1256
REMOTE AAL2 CHANNEL LEVEL RESET IS RECEIVED
Remote aal2 channel level reset is received.
1257
REMOTE AAL2 PATH LEVEL RESET IS RECEIVED
Remote aal2 path level reset is received.
1258
124
REMOTE AAL2 LINK LEVEL RESET IS RECEIVED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Remote aal2 link level reset is received.
1259
LOCAL AAL2 ESTABLISH REQUEST TIME OUT
Local aal2 establish request time out.
1260
LOCAL AAL2 RELEASE REQUEST TIME OUT
Local aal2 release request time out.
1261
LOCAL AAL2 MODIFICATION REQUEST TIME OUT
Local aal2 modification request time out.
1262
DROP STATISTICS STATUS IS INACTIVE
Drop statistics status is inactive.
1263
DROP STATISTICS STATUS IS ACTIVE
Drop statistics status is active.
1264
THE MINUTE IS INVALID
The minute is invalid.
1265
INTERVAL NOT SPECIFIED
The interval is not specified.
1266
OPERATION FAILURE
Operation failed.
1267
PTXTARGET CANNOT TAKE VALUES WHICH ARE
GREATER THAN THE VALUE OF PTXTARGETTOTMAX
PtxTarget cannot take values which are greater than the
value of PtxTargetTotMax.
1268
DROP STATISTICS MEASUREMENT ID MISMATCH
Drop statistics measurement ID mismatch
1269
NO PFL OBJECT CORRESPONDING TO
PFLIDENTIFIER EXISTS IN RNW DATABASE
No PFL object corresponding to PFLIdentifier exists in
RNW database.
1270
PFL deletion not allowed as it is linked to WCEL object.
Deletion of PFL object with PFL identifier is not allowed as
it is linked to a WCEL object.
1271
Issue: 30-0
THERE ARE ALREADY 50 PFL OBJECTS UNDER RNC
OBJECT
DN987378
125
Error messages
General Error Messages of System
Maximum number of PFL objects under an RNC can be
50. This error is reported when there are already 50 PFL
objects under an RNC and user is trying to create more
PFLs under that RNC.
1272
PFL COLLECTION FULL
PFL collection is full under an RNC. There are already 50
PFL objects under the RNC object.
1273
PFL NOT FOUND
No PFL object corresponding to PFLIdentifier exists in
RNW database.
1274
PFL WITH SAME ID ALREADY CREATED
PFL WITH THE SAME ID ALREADY CREATED.
1275
PFL CANNOT BE DELETED IF IT IS USED BY WCEL
OBJECT
PFL deletion is not allowed as it is linked to WCEL object.
1276
VLAN ID FOR UNSECURED AND SECURED M-PLANE
TRAFFIC IS DIFFERENT IN BTS
VLAN ID FOR UNSECURED AND SECURED M-PLANE
TRAFFIC IS DIFFERENT IN BTS.
1277
WSMLC-UEBASEDAGPS CAN BE ENABLED ONLY
WHEN RNC-LCSFUNCTIONALITY IS ENABLED
WSMLC-UEBasedAGPS can only be enabled when RNCLCSfunctionality is enabled.
1278
RNC-LCSFUNCTIONALITY CANT BE DISABLED WHEN
WSMLC-UEBASEDAGPS IS ENABLED
RNC-LCSfunctionality cannot be disabled when WSMLCUEBasedAGPS is enabled.
1279
MAXIMUM NUMBER OF OSPF STUB NETWORK CAN
BE CONFIGURED TO AN AREA EXCEEDED
MAXIMUM NUMBER OF OSPF STUB NETWORK CAN
BE CONFIGURED TO AN AREA EXCEEDED.
1280
A SYNCHRONOUS LIBRARY TRIES TO SYNCHRONIZE
THE REQUEST ID AND A TIMEOUT HAPPENED WHILE
WAITING
A synchronous library tries to synchronize the request ID
and a timeout happened while waiting. The SP process is
out of sync.
126
DN987378
Issue: 30-0
General Error Messages of System
1281
Error messages
ADJI-BLINDHOTARGETCELL MUST BE ENABLED ONLY
WHEN ADJI-MNC IS SAME AS SOURCE CELL MNC.
ADJI-BlindHOTargetCell must be enabled only when ADJIMNC is same as source cell MNC.
1282
ADJI-BLINDHOTARGETCELL MUST BE ENABLED ONLY
WHEN ADJIMCC IS SAME AS SOURCE CELL MCC.
ADJI-BlindHoTargetcell must be enabled only when
ADJIMCC is the same as source cell MCC.
1283
ADJI-BLINDHOTARGETCELL MUST BE ENABLED ONLY
WHEN ADJIRNCID IS SAME AS SOURCE CELL RNCID.
ADJI-BlindHOTargetCell must be enabled only when
AdjiRNCid is the same as source cell RNCid.
1284
WSMLC-UEBASEDAGPS CAN BE ENABLED ONLY IF
WSMLC-LCSINTERFACEOPTION IS SET TO IUPC
WSMLC-UEBasedAGPS can be enabled only if WSMLCLCSInterfaceOption is set to IUPC.
1285
ADJS-LAC IS NOT MODIFIABLE IF TARGET CELL IS
UNDER OWN RNC
ADJS-LAC is not modifiable if target cell is under own
RNC.
1286
ADJS-RAC IS NOT MODIFIABLE IF TARGET CELL IS
UNDER OWN RNC
ADJS-RAC is not modifiable if target cell is under own
RNC.
1287
ADJS-ADJSSCRCODE IS NOT MODIFIABLE IF TARGET
CELL IS UNDER OWN RNC
ADJS-AdjsScrCode is not modifiable if target cell is under
own RNC.
1288
ADJSTXPWRRACH IS NOT MODIFIABLE IF TARGET
CELL IS UNDER OWN RNC
AdjsTxPwrRACH is not modifiable if target cell is under
own RNC.
1289
ADJS-ADJSCPICHTXPWR IS NOT MODIFIABLE IF
TARGET CELL IS UNDER OWN RNC
ADJS-AdjsCPICHTxPwr is not modifiable if target cell is
under own RNC.
1290
Issue: 30-0
WCEL- MBLBRABSETUPENABLED CAN BE ENABLED
ONLY WHEN MULTI BAND LOAD BALANCING LICENSE
IS ON
DN987378
127
Error messages
General Error Messages of System
WCEL- MBLBRABSetupEnabled can only be enabled
when Multi Band Load Balancing license is On.
1291
MULTIPLE ADJI UNDER A SINGLE WCEL HAVING THE
SAME ADJIUARFCN SHOULD NOT HAVE
BLINDHOTARGETCELL AS ENABLED
Multiple ADJIs under a single WCEL having the same
ADJIUARFCN should not have BlindHoTargetCell as
enabled.
1292
ERROR IN RETRIEVING COMMON STATISTICS
COUNTERS
NPZMGR returns this error code in the message
sar_counters_ack_s, if it does not get some common
statistics counter from APP3k.
1293
EGPRS TRX NOT ALLOWED IF DIVIDED 1.
GENERATION FLEXI EDGE DUAL TRX EXISTS AND
HOPPING IS USED WITH OSC
EGPRS TRX is not allowed if Divided 1. generation Flexi
EDGE Dual TRX exists and co TRX is in OSC mode in
BB/Antenna hopping BTS.
1294
HEADER COMPRESSIONS ARE ENABLED FOR THE
BCF
Parameters "Header compression for ML-PPP" and
"Header Compression For UDP IP" are allowed to be
enabled only if BCF is using Packet Abis over TDM.
1295
IPSEC IS NOT SUPPORTED WITH CURRENT ABIS
INTERFACE CONNECTION TYPE
Parameter "IPSec Enabled" is enabled and BCF is using
Packet Abis over TDM, then parameter
”bts_m_plane_tendpoint_ipaddress” should have a valid
value.
1296
INVALID ETPSIG DCHANNEL
ETPSIG D channel does not exist.
1297
MAXIMUM NUMBER OF TCSU EXCEEDED
Maximum number of TCSUs in BSC exceeded.
1298
WCEL-PLMNID MUST BE SAME WITH IUCS/IUPSPLMNID.
WCEL-PLMNid must be same with IUCS/IUPS-PLMNid.
1299
128
WCEL-DCELLHSDPAENABLED CAN BE SET AS
ENABLED ONLY IF WCEL-HSDPAENABLED IS
ENABLED.
DN987378
Issue: 30-0
General Error Messages of System
Error messages
WCEL-DCellHSDPAEnabled can be set as enabled only if
WCEL-HSDPAEnabled is enabled.
1300
FILE IS NOT GZIP FORMAT
The file is not in gzip format (rfc1952). For eSW files
(AEMxxxxx.IMG), it is usually a gzip file under a DX
header (the DX header is added by dxloada). During eSW
update, STE will check whether the file is gzip or not.
1301
BIOS VERSION UNKNOWN
The BIOS version cannot be inquired from flash or disk file.
1302
MANUFACTURER UNKNOWN
Cannot find the manufacturer of the board.
1303
CONGESTION CONTROL CANNOT ENABLED FOR BCF
UNLESS RELEVANT PARAMETERS ARE DEFINED
Parameters
1304
UPLINK TRAFFIC SHAPING CANNOT ENABLED FOR
BCF UNLESS RELEVANT PARAMETER IS DEFINED
Parameter
1305
HSDPAMAXBITRATEUL MUST BE HIGHER THAN OR
EQUAL TO HSDPAMINALLOWEDBITRATEUL
HSDPAMaxBitrateUL must be higher than or equal to
HSDPAminAllowedBitrateUL.
1306
PARAMETER UPDATING FAILED TO PROTECTING ETP
PARAMETER UPDATING FAILED TO PROTECTING ETP.
1307
EXTENDED CCCH FEATURE IS NOT IN USE IN BSC
Extended CCCH feature cannot be enabled due to that
there is no licence installed in BSC or licence has been
expired or licence is in OFF/CONF state.
1308
EXTENDED CCCH CAPACITY LICENCE EXCEEDED
Capacity of the Extended CCCH licence (Extended CCCH)
exceeded.
1309
WSMLC-NETWORKBASEDAGPS CAN BE ENABLED
ONLY WHEN RNC-LCSFUNCTIONALITY IS ENABLED
WSMLC-NetworkBasedAGPS CAN BE ENABLED ONLY
WHEN RNC-LCSFUNCTIONALITY IS ENABLED.
1310
Issue: 30-0
RNC-LCSFUNCTIONALITY CANT BE DISABLED WHEN
WSMLC-NWBASEDAGPS IS ENABLED
DN987378
129
Error messages
General Error Messages of System
RNC-LCSfunctionality cannot be disabled when WSMLCNwBasedAGPS is enabled.
1311
NO PRIOR HLRU UNIT EXSITS
This error shows that there is no PriorHLRU which handles
the replication of profile data in datafull HLR.
1312
APP3K MEMORY TEST FAILED
APP3k memory test failed.
1313
IF WCEL-DCELLHSDPAENABLED IS SET TO ENABLED
THEN WCEL-SECTORID SHOULD NOT BE SET AS
DEFAULT.
If WCEL-DCellHSDPAEnabled is set to enabled then
WCEL-SectorID should not be set as default.
1314
SIB5 TRANSMISSION BY RRA HAS FAILED
SIB5 transmission by RRA has failed.
1315
HIGH SPEED CELL FACH IS ENABLED IN RNC BUT
DISABLED IN BTS
High speed cell FACH is enabled in RNC but disabled in
BTS.
1316
SYNCHRONIZATION IS LOST BETWEEN BTS AND RNC
FOR HS COMMON CHANNELS
Synchronization is lost between BTS and RNC for HS
common channels.
1317
INTERROGATE LAN MEASUREMENT DATA OF
VIRTUAL UNITS IS NOT SUPPORTED
Interrogate LAN measurement data of virtual units is not
supported.
1318
COUNT OF REDISTRIBUTED INTERFACE ROUTES IN
UNIT EXCEEDS MAXIMUM NUMBER
Count of redistributed interface routes in unit exceeds the
maximum number.
1319
WCEL-HSDPAENABLED MUST BE SET AS ENABLED IF
WCEL-HSDPA64QAMALLOWED IS ENABLED.
WCEL-HSDPAEnabled must be set as enabled if WCELHSDPA64QAMallowed is enabled.
1320
CALL DOES NOT EXIST
Call does not exist.
130
DN987378
Issue: 30-0
General Error Messages of System
1321
Error messages
HDLC LINK RECEIVED ON ACTIVE ETP
HDLC link received on active ETP.
1322
HDLC LINK IS NOT PRESENT
HDLC link is not present.
1323
HDLC LINK VALIDATION FAILED
HDLC link validation failed.
1324
OPTION MULTI-CONTROLLER TC IS NOT IN USE IN
BSC
MCTC feature is not enabled in BSC. Either feature licence
is not valid or feature status is in disabled state.
1325
ETP SWITCHOVER IN PROGRESS
ETP switchover in progress.
1326
UNIT HAS ALREADY PAIR
Unit has already pair.
1327
GBU HAS RESOURCE
There is resource configured to GBU unit.
1328
NO FORWARD PATH TO BCF ADDRESS
If the Abis is a routed backhaul (L3), configure an Gateway
IP address through which this BCF can be reached. If the
Abis is a switched backhaul (L2), add an EL0 address that
is in the same subnet as the BCF address.
1329
WCEL-HSFACHENABLED CAN BE ENABLED ONLY
WHEN RNFC-FRLCENABLED IS ENABLED.
WCEL-HSFACHEnabled can be enabled only when
RNFC-FRLCEnabled is enabled.
1330
WCEL-HSFACHENABLED CAN BE ENABLED ONLY
WHEN RNFCHSDPADYNAMICRESOURCEALLOCATION IS ENABLED
WCEL-HSFACHEnabled can be enabled only when
RNFC-HSDPADynamicResourceAllocation is enabled
1331
WCEL-HSFACHENABLED CAN BE ENABLED ONLY
WHEN RNC-FLEXULRLCENABLED IS ENABLED
WCEL-HSFACHEnabled can be enabled only when RNCFlexULRLCEnabled is enabled.
Issue: 30-0
DN987378
131
Error messages
General Error Messages of System
1332
HSFACHENABLED CAN BE SET TO ENABLED ONLY
WHEN THE ALL CDSP-DH CARDS ARE WITH UPCAP
MODE
HSFACHEnabled can be set to enabled only when the all
CDSP-DH cards are with UPCAP mode
1333
WCEL-HSFACHENABLED CAN BE ENABLED ONLY
WHEN WCEL-HSDPAENABLED IS ENABLED
WCEL-HSFACHEnabled can be enabled only when
WCEL-HSDPAEnabled is enabled.
1334
HSFACHENABLED CAN BE ENABLED ONLY WHEN
WCEL-POWERSAVEHSPATYPE HAS NO_HSPA_CNF_C
OR DEF_C OR HSPA_5_C VALUES
HSFACHEnabled can be enabled only when WCELPowerSaveHSPAType has no_hspa_cnf_c or def_c or
hspa_5_c values
1335
HSFACH CANNOT BE ACTIVATED BECAUSE THE
HSFACH LICENSE STATE IS CONFIG/OFF INSTEAD OF
ON
HSFACH cannot be activated because the HSFACH
license state is CONFIG/OFF instead of ON.
1336
VALUE OF PRIFORHSFACHDTCH SHOULD BE LESS
THAN
PRIFORBACKARP1,PRIFORBACKARP2,PRIFORBACKA
RP3
Value of PRIFORHSFACHDTCH should be less than
PriForBackARP1,PriForBackARP2,PriForBackARP3.
1337
VALUE OF PRIFORHSFACHDTCH SHOULD BE LESS
THAN
PRIFORINTTHP1ARP1,PRIFORINTTHP1ARP2,PRIFORI
NTTHP1ARP3
Value of PRIFORHSFACHDTCH should be less than
PriForIntTHP1ARP1,PriForIntTHP1ARP2,PriForIntTHP1A
RP3.
1338
VALUE OF PRIFORHSFACHDTCH SHOULD BE LESS
THAN
PRIFORINTTHP2ARP1,PRIFORINTTHP2ARP2,PRIFORI
NTTHP2ARP3
Value of PRIFORHSFACHDTCH should be less than
PriForIntTHP2ARP1,PriForIntTHP2ARP2,PriForIntTHP2A
RP3.
132
DN987378
Issue: 30-0
General Error Messages of System
1339
Error messages
VALUE OF PRIFORHSFACHDTCH SHOULD BE LESS
THAN
PRIFORINTTHP3ARP1,PRIFORINTTHP3ARP2,PRIFORI
NTTHP3ARP3
Value of PRIFORHSFACHDTCH should be less than
PriForIntTHP3ARP1,PriForIntTHP3ARP2,PriForIntTHP3A
RP3.
1340
IF WCEL-MIMOWITH64QAMUSAGE IS ENABLED, THEN
WCEL-MIMOENABLED MUST BE ENABLED
If WCEL-MIMOWith64QAMUsage is enabled, then WCELMIMOEnabled must be enabled.
1341
IF WCEL-MIMOWITH64QAMUSAGE IS ENABLED, THEN
WCEL-HSDPA64QAMALLOWED MUST BE ENABLED
If WCEL-MIMOWith64QAMUsage is enabled, then WCELHSDPA64QAMallowed must be enabled.
1342
INTERNAL ERROR FROM APP3K API
Internal error from APP3K API
1343
TIME OUT IN APP3K SUPERVISION
Time out in APP3k supervision
1344
INCORRECT SUPERVISION ACK MESSAGE FROM
APP3K
Incorrect supervision ack message from APP3k
1345
PR_RXLEVEL FEATURE IS NOT IN USE IN BSC
Precise RX Level Measurement feature is not enabled in
BSC. Either feature licence is not valid or feature status is
in disabled state.
1346
PR_TIMING_ADV FEATURE IS NOT IN USE IN BSC
Precise Timing Advance Measurement feature is not
enabled in BSC. Either feature licence is not valid or
feature status is in disabled state.
1347
PR_POWER_LEVEL FEATURE IS NOT IN USE IN BSC
Precise Power Level Measurement feature is not enabled
in BSC. Either feature licence is not valid or feature status
is in disabled state.
1348
ADJ_RXLEVEL FEATURE IS NOT IN USE IN BSC
Adjacent RX Level Measurement feature is not enabled in
BSC. Either feature licence is not valid or feature status is
in disabled state.
Issue: 30-0
DN987378
133
Error messages
General Error Messages of System
1349
MEASUREMENT TABLE ALLOCATION FAILED
The Measurement cannot be activated due to insufficient
memory. The measurement type can be specified in the
log.
1350
illegal physical information
Illegal physical information of SDH port, used in Ui5 MGW
1351
BOTH SETS EXIST
Both set_index1 and set_index2 exist at one SCNAM card,
used when delete et in Ui MGW.
1352
ADMINPICSTATE SET BY OPERATOR IS MISMATCHING
WITH PIC STATE RECEIVED FROM NODE-B.
AdminPICState set by operator is mismatching with PIC
State received from Node-B.
1353
DATAFUL FEATURE STATE IS WRONG
The error shows that the current datafull feature state is
not good from the requested service point of view.
1354
IDENTITY NOT FOUND FROM THE HLR
The error means that the subscriber was not found in the
HLR. This does not mean the same as unknown
subscriber as there is a possibility that the subscriber exits
in the BACKEND database.
1355
CONFLICTING TRX STARTING MODE
TRX Starting Mode has been defined incorrectly
1356
BCF IP ADDRESS IS DIFFERENT THAN DEFINED IN
SCTP ASSOCIATION
BCF C/U OR M-PLANE IP ADDRESS (OR SUBNET
MASK) IS DIFFERENT THAN DEFINED IN SCTP
ASSOCIATION USED BY OMUSIG OR TRXSIG.
1357
FAIL TO GET VIRTUAL CIRCUIT PCM RANGE
When add a remote-tdm semipermanent connection, SCLI
back end (CM4) willl call ATVLIB to reserver a virtual PCM
line number. If this action fails, SCLI back end will
feedback this error number.
1358
TDM NOT SUPPORTED IN MCBSC
MultiController BSC does not support TDM in stand alone
configuration.
134
DN987378
Issue: 30-0
General Error Messages of System
1359
Error messages
VALUE OF PRIFORHSFACHDTCH MUST BE LESS
THAN PRIFORINTSIGNALING
Value of PriForHSFACHDTCH must be less than
PriForIntSignaling.
1360
WCEL-ADMINPICSTATE CAN BE AUTOMATIC OR
ACTIVE ONLY WHEN WCEL-HSUPA2MSTTIENABLED
IS ENABLED
WCEL-AdminPICState can be automatic or active only
when WCEL-HSUPA2MSTTIEnabled is enabled.
1361
RNC-FASTDORMANCYENABLED CAN BE ENABLED
ONLY WHEN RNC-MSACTIVITYSUPERVISION IS
GREATER THAN 0
RNC-FastDormancyEnabled can be enabled only when
RNC-MSActivitySupervision is greater than 0.
1362
RNC-FASTDORMANCYENABLED CAN BE ENABLED
ONLY WHEN RNC-MSACTIVITYSUPERVISION IS
GREATER THAN ZERO
RNC-FastDormancyEnabled can be enabled only when
RNC-MSActivitySupervision is greater than zero.
1363
COUNT OF REDISTRIBUTED STATIC ROUTES IN UNIT
EXCEEDS THE MAXIMUM NUMBER
Count of redistributed static routes in unit exceeds the
maximum number.
1364
THE PARAMETER SHOULD NOT BE SAME
When adding a TDM-TDM semi-permanent connection,
the input two circuit should not be same.
1365
THE PARAMETER CRCT AND TSL SHOULD NOT BE
INPUT AT THE SAME TIME
When adding a Remote-TDM semi-permanent connection,
parameter 'crct' and 'tsl' should not be input at the same
time.
1366
THE PARAMETER IPV4 AND IPV6 SHOULD NOT BE
INPUT AT THE SAME TIME
When adding a destination ip address to a TDM-IP or
Remote-TDM semi-permanent connection, parameter
'ipv4' and 'ipv6' should not be input at the same time.
1367
MAXIMUM HS-FACH H-RNTI LIMIT REACHED (PER
CELL 600/PER BTS 1024)
Maximum HS-FACH H-RNTI limit reached (per cell 600/per
BTS 1024).
Issue: 30-0
DN987378
135
Error messages
General Error Messages of System
1368
UNIT HAS NO PCUSIG CONFIGURATION
Unit has no pcusig configuration
1369
UNIT HAS PCUSIG CONFIGURATION
Unit has pcusig configuration
1370
RNFC-HSPAOVERIUREXT PARAMETER CAN BE
ENABLED ONLY WHEN RNFC-HSDPAMOBILITY IS
ENABLED
RNFC-HSPAOverIurExt parameter can be enabled only
when RNFC-HSDPAMobility is enabled.
1371
RNFC-HSPAOVERIUREXT PARAMETER CAN BE
ENABLED ONLY WHEN RNFCHSDPADYNAMICRESOURCEALLOCATION IS ENABLED
RNFC-HSPAOverIurExt parameter can be enabled only
when RNFC-HSDPADynamicResourceAllocation is
enabled.
1372
RNAC NOT FOUND
No RNAC object corresponding to RNACIdentifier exists in
RNW database.
1373
RNPS NOT FOUND
No RNPS object corresponding to RNPSIdentifier exists in
RNW database.
1374
RNRLC NOT FOUND
No RNRLC object corresponding to RNRLCIdentifier exists
in RNW database.
1375
RNTRM NOT FOUND
No RNTRM object corresponding to RNTRMIdentifier
exists in RNW database.
1376
RNFC NOT FOUND
No RNFC object corresponding to RNFCIdentifier exists in
RNW database.
1377
RNHSPA NOT FOUND
No RNHSPA object corresponding to RNHSPAIdentifier
exists in RNW database.
1378
RNMOBI NOT FOUND
No RNMOBI object corresponding to RNMOBIIdentifier
exists in RNW database.
136
DN987378
Issue: 30-0
General Error Messages of System
1379
Error messages
RNCGEN NOT FOUND
No RNCGEN object corresponding to RNCGENIdentifier
exists in RNW database.
1380
RNAC WITH SAME ID ALREADY CREATED
RNAC with the same ID is already created.
1381
RNPS WITH SAME ID ALREADY CREATED
RNPS with the same ID is already created.
1382
RNRLC WITH SAME ID ALREADY CREATED
RNRLC with the same ID is already created.
1383
RNTRM WITH SAME ID ALREADY CREATED
RNTRM with the same ID is already created.
1384
RNFC WITH SAME ID ALREADY CREATED
RNFC with the same ID is already created.
1385
RNHSPA WITH SAME ID ALREADY CREATED
RNHSPA with the same ID is already created.
1386
RNMOBI WITH SAME ID ALREADY CREATED
RNMOBI with the same ID is already created.
1387
RNCGEN WITH SAME ID ALREADY CREATED
RNCGEN with the same ID is already created.
1388
UNIT HAS NO PAIR CREATED
Unit has no pair created.
1389
UNIT STATE MUST BE SP BECAUSE IT HAS NO 2G
RESOURCES TO SUPERVISE
The working state of the unit must be passive (SP)
because it has no 2G resources to supervise.
1390
UNIT STATE MUST BE WO BECAUSE IT HAS 2G
RESOURCES TO SUPERVISE
The working state of the unit must be active (WO) because
it has 2G resources to supervise.
1391
SITE TYPE DOES NOT SUPPORT OSC
OSC is not supported for the site type.
1392
Issue: 30-0
WRONG CELL INDEX SPECIFIED IN THE CELL SETUP
MESSAGE WHICH IS SENT TO L2
DN987378
137
Error messages
General Error Messages of System
Wrong cell index specified in the cell setup message which
is sent to L2
1393
WRONG BCCH QUEUE TIME PARAMETER SPECIFIED
IN THE CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong BCCH Queue time parameter specified in the cell
setup message which is sent to L2
1394
WRONG CCCH QUEUE TIME PARAMETER SPECIFIED
IN THE CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong CCCH Queue time parameter specified in the cell
setup message which is sent to L2
1395
WRONG DCCH QUEUE TIME PARAMETER SPECIFIED
IN THE CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong DCCH Queue time parameter specified in the cell
setup message which is sent to L2
1396
WRONG DTCH QUEUE TIME PARAMETER SPECIFIED
IN THE CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong DTCH Queue time parameter specified in the cell
setup message which is sent to L2
1397
WRONG STATISTICS REPORT PERIOD PARAMETER
SPECIFIED IN THE CELL SETUP MESSAGE WHICH IS
SENT TO L2
Wrong statistics report period parameter specified in the
cell setup message which is sent to L2
1398
WRONG STATISTICS REPORT NUMBER PARAMETER
SPECIFIED IN THE CELL SETUP MESSAGE WHICH IS
SENT TO L2
Wrong statistics report number parameter specified in the
cell setup message which is sent to L2
1399
WRONG STATISTICS LOAD REPORT NUMBER
PARAMETER SPECIFIED IN THE CELL SETUP
MESSAGE WHICH IS SENT TO L2
Wrong statistics load report number parameter specified in
the cell setup message which is sent to L2
1400
WRONG STATISTICS LOAD MEASUREMENT NUMBER
PARAMETER SPECIFIED IN THE CELL SETUP
MESSAGE WHICH IS SENT TO L2
Wrong statistics load measurement number parameter
specified in the cell setup message which is sent to L2
138
DN987378
Issue: 30-0
General Error Messages of System
1401
Error messages
WRONG STATISTICS OVERLOAD THRESHOLD
PARAMETER SPECIFIED IN THE CELL SETUP
MESSAGE WHICH IS SENT TO L2
Wrong statistics overload threshold parameter specified in
the cell setup message which is sent to L2
1402
WRONG STATISTICS OVERLOAD MARGIN
PARAMETER SPECIFIED IN THE CELL SETUP
MESSAGE WHICH IS SENT TO L2
Wrong statistics overload margin parameter specified in
the cell setup message which is sent to L2
1403
WRONG CHANNEL ALLOWED DATA PARAMETER
SPECIFIED IN THE CELL SETUP MESSAGE WHICH IS
SENT TO L2
Wrong channel allowed data parameter specified in the cell
setup message which is sent to L2
1404
WRONG CR PENDING TIME PARAMETER SPECIFIED
IN THE CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong cr pending time parameter specified in the cell
setup message which is sent to L2
1405
WRONG UL DL INACTIVITY TIMER PARAMETER
SPECIFIED IN THE CELL SETUP MESSAGE WHICH IS
SENT TO L2
Wrong UL DL inactivity timer parameter specified in the
cell setup message which is sent to L2
1406
WRONG PAGING WINDOW SIZE PARAMETER
SPECIFIED IN THE CELL SETUP MESSAGE WHICH IS
SENT TO L2
Wrong paging window size parameter specified in the cell
setup message which is sent to L2
1407
WRONG PAGING DISTANCE PARAMETER SPECIFIED
IN THE CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong paging distance parameter specified in the cell
setup message which is sent to L2
1408
WRONG OSE PID PARAMETER SPECIFIED IN THE
CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong OSE PID parameter specified in the cell setup
message which is sent to L2
1409
Issue: 30-0
WRONG CELL PARAMETER SPECIFIED IN THE CELL
SETUP MESSAGE WHICH IS SENT TO L2
DN987378
139
Error messages
General Error Messages of System
Wrong cell parameter specified in the cell setup message
which is sent to L2
1410
WRONG PA ID COUNT PARAMETER SPECIFIED IN THE
CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong PA ID count parameter specified in the cell setup
message which is sent to L2
1411
WRONG NUMBER OF TRCH PARAMETER SPECIFIED
IN THE TRCH CONFIGURATION MESSAGE WHICH IS
SENT TO L2
Wrong number of TRCH parameter specified in the TRCH
configuration message which is sent to L2
1412
WRONG DUP SID PARAMETER SPECIFIED IN THE
CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong DUP SID parameter specified in the cell setup
message which is sent to L2
1413
WRONG PICH GROUP PARAMETER SPECIFIED IN THE
CELL SETUP MESSAGE WHICH IS SENT TO L2
Wrong PICH Group parameter specified in the cell setup
message which is sent to L2
1414
WRONG NUMBER OF TRCH SPECIFIED IN THE TRCH
RECONFIGURATION MESSAGE WHICH IS SENT TO L2
Wrong number of TRCH specified in the TRCH
reconfiguration message which is sent to L2
1415
WRONG UL DL INACTIVITY TIMER PARAMETER
SPECIFIED IN THE MS ADD MESSAGE WHICH IS SENT
TO L2
Wrong UL DL inactivity timer parameter specified in the
MS Add message which is sent to L2
1416
TOO MANY LCHS IN THE MS ADD MESSAGE WHICH IS
SENT TO L2
Too many LCHs in the MS Add message which is sent to
L2
1417
TOO MANY SRBS IN THE MS ADD MESSAGE WHICH IS
SENT TO L2
Too many SRBs in the MS Add message which is sent to
L2
1418
140
UNKNOWN OPERATION SPECIFIED IN THE MS ADD
MESSAGE WHICH IS SENT TO L2
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Unknown operation specified in the MS Add message
which is sent to L2
1419
CONFIGURATION ATTEMPTED FOR NON EXISTING UE
IN THE MS ADD MESSAGE WHICH IS SENT TO L2
Configuration attempted for non existing UE in the MS Add
message which is sent to L2
1420
PROGRAM BLOCK STOPPED
The operator has stopped the program block.
1421
UPDATES TO DISKLOG ARE FORBIDDEN
The program block or operator has forbidden updates in
the disklog (log in state 02h or 03h). Change the state or
wait until it has been changed.
1422
UPDATE SEQUENCE NUMBER DOES NOT MATCH
The update number in the update message does not
match with the update number of the last update in the
disklog.
1423
1 DISK NOT OK, NO DUMP
One of the disks does not function. Dumping is not carried
out since it is not determined, in the message
dump_req_s, to be carried out when only one disk is
functioning.
1424
1 DISK NOT OK, DUMP ON OTHER
One of the disks does not function. Dumping is carried out
on the other disk since this is determined in the message
dump_req_s.
1425
BOTH DISKS NOT OK, NO DUMP
Both disks are out of order. Dumping can not be carried
out.
1426
DUMP IS ALREADY BEING DONE
Dumping is already being done. The next request can be
carried out when the previous one is executed.
1427
WRITING IN DATABASE IS FORBIDDEN
Writing in the database is forbidden (either by operator or
program block). Release writing, or wait until it has been
released.
1428
Issue: 30-0
NO CONSISTENT DATABASE
DN987378
141
Error messages
General Error Messages of System
The database on both disks is not consistent. Loading can
not be carried out of inconsistent databases.
1429
BTS SOFTWARE DOES NOT SUPPORT EXTENDED
RANGE CELL FEATURE
BTS software version earlier than EX 4.1 does not support
the Extended Range Cell Feature.
1430
INITIALIZATION FAILED
The execution of initialization routine has failed.
1431
TEST SIGNAL OK
The characteristics of the measured test signal were within
permitted limits.
1432
NULL SIGNAL DETECTED
The signal to be measured was not received in the test.
1433
UNSYMMETRICAL SIGNAL DETECTED
An unsymmetrical test signal was detected.
1434
TOO LOW SIGNAL
The strength of the measured test signal was too low.
1435
TOO HIGH SIGNAL
The strength of the measured test signal was too high.
1436
SIGNAL ERROR
The measured test signal was incorrect.
1437
COMMAND NOT POSSIBLE, UNIT HAS IUA
CONFIGURATION
Command not possible, unit has IUA configuration.
1438
IF WCEL-DCELLANDMIMOUSAGE IS ENABLED WITH
VALUE 1 OR 2, THEN WCEL-FDPCHENABLED MUST
BE ENABLED.
If WCEL-DCellAndMIMOUsage is enabled with value 1 or
2, then WCEL-FDPCHEnabled must be enabled.
1439
IF WCEL-DCELLANDMIMOUSAGE IS ENABLED WITH
VALUE 1 OR 2, THEN WCEL-DCELLHSDPAENABLED
MUST BE ENABLED.
If WCEL-DCellAndMIMOUsage is enabled with value 1 or
2, then WCEL-DCellHSDPAEnabled must be enabled.
142
DN987378
Issue: 30-0
General Error Messages of System
1440
Error messages
IF WCEL-DCELLANDMIMOUSAGE IS ENABLED WITH
VALUE 1 OR 2, THEN WCEL-MIMOENABLED MUST BE
ENABLED.
If WCEL-DCellAndMIMOUsage is enabled with value 1 or
2, then WCEL-MIMOEnabled must be enabled.
1441
IF WCEL-DCELLANDMIMOUSAGE IS ENABLED WITH
VALUE 2, THEN WCEL-HSDPA64QAMALLOWED MUST
BE ENABLED.
If WCEL-DCellAndMIMOUsage is enabled with value 2,
then WCEL-HSDPA64QAMallowed must be enabled.
1442
IF WCEL-DCELLANDMIMOUSAGE IS ENABLED WITH
VALUE 2, THEN WCEL-MIMOWITH64QAMUSAGE MUST
BE ENABLED.
If WCEL-DCellAndMIMOUsage is enabled with value 2,
then WCEL-MIMOWith64QAMUsage must be enabled.
1443
ETHERNET RING/PATH PROTECTION LICENSE IS NOT
IN USE.
Ethernet Ring/Path Protection is not in use.
1444
ETHERNET RING/PATH PROTECTION FEATURE BCF
CAPACITY IS EXCEEDED.
Ethernet Ring/Path Protection BCF Capacity is exceeded.
1445
MULTICAST GROUP ID TABLE OF NPELIB IS FULL.
Multicast group ID table of NPELIB is full.
1446
INVALID MULTICAST GROUP ID
Invalid multicast group ID
1447
FLOW MONITORING IS NOT ACTIVE.
Flow monitoring is not active.
1448
FLOW MONITORING IS ALREADY ACTIVE.
Flow monitoring is already active.
1449
BTS SOFTWARE DOES NOT SUPPORT THE
ETHERNET RING/PATH PROTECTION FEATURE.
BTS software does not support the Ethernet Ring/Path
protection feature.
1450
SOME ACTIVE UNITS ARE NOT IN WOEX STATE
Some active units are not in WOEX state when cutover to
a new software package.
Issue: 30-0
DN987378
143
Error messages
General Error Messages of System
1451
SOME UNITS HAVE FAULTY FLAG
Some units have FAULTY flag when cutover to a new
software package.
1452
OMU IS NOT IN NORMAL WORKING STATE
OMU is not in normal working state.
1453
THE SELECTED NEW PACKAGE UNIT IS NOT
REDUNDANT
The selected unit is in WOEX state and cannot be added
to trial.
1454
NO REDUNDANT UNIT TO BE SELECTED AS THE NEW
PACKAGE UNIT
There is no redundant unit to be selected as the new
package unit
1455
ALL CHILD UNITS ARE NOT IN TRIAL
The virtual manager unit cannot be added to trial because
all of the child units are not in trial.
1456
A CHILD UNIT IS IN WO STATE
The child of virtual manager unit is in WO state.
1457
SUITABLE OLD PACKAGE UNIT IN WOEX STATE IS
NOT FOUND
Suitable unit in WOEX state in telecom side is not found.
1458
THE SELECTED OLD PACKAGE UNIT IS NOT IN WOEX
STATE
The selected old package unit in telecom side is not in
WOEX state.
1459
PCI-EX RESOURCES OF THE PCI DEVICE NOT FOUND
The PCI-EX resources of the specified PCI device are not
found.
1460
NOT POSSIBLE TO UNLOCK EGPRS TRX WITHOUT
BTS LOCKING WHEN USING ANTENNA HOPPING
WITH OSC
Not possible to unlock EGPRS TRX without locking BTS
when using antenna hopping with OSC.
1461
USER OPERATION WOULD CAUSE TRAFFIC CUT
User operation would cause traffic cut.
1462
144
TRANSACTION DOES NOT EXIST
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The transaction ID does not exist.
1463
TRANSACTION ALREADY EXISTS
The transaction already exists.
1464
PCI-E DEVICE NOT FOUND
A specific PCI-E device was searched but was not found
either because it does not exist or it has not been
configured.
1465
PCI-E PORT NUMBER ERROR
Either the input PCI-E port number or the number of the
port is incorrect.
1466
PCI-E PORT INFORMATION NOT SUPPORT
Getting the PCI-E port information is not supported.
1467
PREBTS COLLECTION FULL
PREBTS collection is full under an RNC. There are already
1000 PREBTS objects under the RNC object.
1468
NO PREBTS OBJECT CORRESPONDING TO
PREBTIDENTIFIER EXISTS IN RNW DATABASE
No PREBTS object corresponding to PREBTSIdentifier
exists in RNW database.
1469
PREBTS WITH THE SAME ID ALREADY CREATED IN
RNWDB
PREBTS with the same ID has been created already in
RNWDB.
1470
ERROR IS THROWN WHEN ANY OF THE PAPUS IN
THE PAPU GROUP DOES NOT HAVE A GBU PAIR UNIT
Error is thrown when any of the PAPUs in the papu group
does not have a GBU pair unit.
1471
AIR PATH LOSS MEASUREMENT FEATURE IS NOT IN
USE IN BSC
Air Path Loss Measurement feature is not enabled in BSC.
Either the feature license is not valid or the feature status
is in disabled state.
1472
NOT IN SS7 STATISTICS
Not in SS7 statistics.
1473
SFU SUPERVISION HAS FAILED
SFU supervision has failed.
Issue: 30-0
DN987378
145
Error messages
General Error Messages of System
1474
OSC DFR FEATURE IS NOT IN USE IN BSC
The OSC (Orthogonal Subchannel) Full Rate feature
cannot be enabled either because license is not installed in
BSC (Base Station Controller) or license has expired or
license is in wrong state.
1475
OSC DFR CAPACITY LICENSE EXCEEDED
Capacity of the OSC Full Rate license has exceeded.
1476
OSC DFR CANNOT OPERATE WITHOUT AMR FR
OSC (Orthogonal Sub Channel) Full Rate feature cannot
operate without AMR FR.
1477
CSDAP, PACKET ABIS OR 8KTRAU REQUIRED FOR
OSC DFR
OSC (Orthogonal Sub Channel) Full Rate feature cannot
operate without CSDAP, Packet ABIS OR 8KTRAU.
1478
CSDAP OR 8KTRAU REQUIRED FOR OSC DFR
OSC (Orthogonal Sub Channel) Full Rate feature cannot
operate without CSDAP OR 8KTRAU.
1479
BTS SW DOES NOT SUPPORT OSC DFR
OSC Full rate with SAIC MS is not supported in BTS SW.
1480
NE ACCOUNT DOES NOT EXIST
NE account has not been set. The LDAP client used for
authenticating and authorizing needs the NE account for
performing LDAP operations.
1481
8K TRAU FOR DFR CANNOT BE DEACTIVATED WITH
OSC FULL RATE IN USE
When 8k TRAU for DFR is modified to forbidden and OSC
Full Rate with SAIC MS is in use, then CSDAP must be
attached to BCF and CSDAP license should be active.
1482
CONCURRENT USE OF 8K TRAU FOR DFR AND
PACKET ABIS NOT SUPPORTED
Concurrent use of 8k TRAU for DFR and Packet Abis is
not supported in a BTS.
1483
8K TRAU FOR DFR IS NOT IN USE IN BSC
Parameter 8k TRAU for DFR enabled cannot be enabled
due to that there is no license installed in BSC or license
has expired or license is in wrong state.
146
DN987378
Issue: 30-0
General Error Messages of System
1484
Error messages
BTS SOFTWARE DOES NOT SUPPORT 8K TRAU FOR
DFR
BTS software version does not support 8k TRAU for DFR.
1485
PACKET ABIS IP/TDM AGGREGATION LICENSE IS NOT
IN USE
Packet Abis IP/TDM Aggregation license is not in use.
1486
PACKET ABIS IP/TDM AGGREGATION CAPACITY HAS
EXCEEDED
Packet Abis IP/TDM Aggregation capacity has exceeded.
1487
BTS SW DOES NOT SUPPORT PACKET ABIS IP/TDM
AGGREGATION FEATURE
BTS SW does not support Packet Abis IP/TDM
Aggregation feature.
1489
LDAP SUCCESS STATUS
LDAP success status.
1490
LDAP OPERATIONS ERROR
Indicates that the operation is not properly sequenced with
relation to other operations (of same or different type). For
example, this code is returned if the client attempts to
StartTLS while there are other uncompleted operations or
if a TLS layer was already installed.
1491
LDAP PROTOCOL ERROR
Indicates that the server received data that is not wellformed. For Bind operation only, this code is also used to
indicate that the server does not support the requested
protocol version. For Extended operations only, this code is
also used to indicate that the server does not support (by
design or configuration) the Extended operation associated
with the requestName. For request operations specifying
multiple controls, this may be used to indicate that the
server cannot ignore the order of the controls as specified,
or that the combination of the specified controls is invalid
or unspecified.
1492
LDAP TIMELIMIT EXCEEDED
Indicates that the time limit specified by the client has
exceeded before the operation could be completed.
1493
LDAP SIZE LIMIT EXCEEDED
Indicates that the size limit specified by the client has
exceeded before the operation could be completed.
Issue: 30-0
DN987378
147
Error messages
General Error Messages of System
1494
LDAP COMPARE FALSE
Indicates that the Compare operation has successfully
completed and the assertion has evaluated to FALSE or
Undefined.
1495
LDAP COMPARE TRUE
Indicates that the Compare operation has successfully
completed and the assertion has evaluated to TRUE.
1496
LDAP STRONG AUTH NOT SUPPORTED
Indicates that the authentication method or mechanism is
not supported.
1497
LDAP STRONG AUTH REQUIRED
Indicates that the server requires a strong(er)
authentication in order to complete the operation. When
used with the Notice of Disconnection operation, this code
indicates that the server has detected that an established
security association between the client and server has
unexpectedly failed or has been compromised.
1498
LDAP PARTIAL RESULTS
Only partial results returned.
1499
LDAP REFERRAL
Indicates that a referral needs to be chased to complete
the operation.
1500
LDAP ADMINLIMIT EXCEEDED
Indicates that an administrative limit has been exceeded.
1501
LDAP UNAVAILABLE CRITICAL EXTENSION
Indicates that a critical control is unrecognized.
1502
LDAP CONFIDENTIALITY REQUIRED
Indicates that data confidentiality protections are required.
1503
LDAP SASL BIND IN PROGRESS
Indicates that the server requires the client to send a new
bind request, with the same SASL mechanism, to continue
with the authentication process.
1504
LDAP NO SUCH ATTRIBUTE
Indicates that the named entry does not contain the
specified attribute or attribute value.
1505
148
LDAP UNDEFINED TYPE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Indicates that a request field contains an unrecognized
attribute description.
1506
LDAP INAPPROPRIATE MATCHING
Indicates that an attempt was made (e.g., in an assertion)
to use a matching rule not defined for the attribute type
concerned.
1507
LDAP CONSTRAINT VIOLATION
Indicates that the client supplied an attribute value that
does not conform to the constraints placed upon by the
data model. For example, this code is returned when
multiple values are supplied to an attribute that has a
SINGLE-VALUE constraint.
1508
LDAP TYPE OR VALUE EXISTS
Indicates that the client supplied an attribute or value to be
added to an entry, but the attribute or value already exists.
1509
LDAP INVALID SYNTAX
Indicates that a purported attribute value does not conform
to the syntax of the attribute.
1510
LDAP NO SUCH OBJECT
Indicates that the object does not exist in the DIT.
1511
LDAP ALIAS PROBLEM
Indicates that an alias problem has occurred. For example,
the code used to indicate an alias has been de-referenced
that names no object.
1512
LDAP INVALID DN SYNTAX
Indicates that an LDAPDN or RelativeLDAPDN field (e.g.,
search base, target entry, ModifyDN newrdn, etc.) of a
request does not conform to the required syntax or
contains attribute values that does not conform to the
syntax of the attribute's type.
1513
LDAP IS LEAF
The object specified is a leaf.
1514
LDAP ALIAS DEREF PROBLEM
Indicates that a problem occurred while dereferencing an
alias. Typically, an alias was encountered in a situation
where it was not allowed or where access was denied.
1515
Issue: 30-0
LDAP INAPPROPRIATE AUTH
DN987378
149
Error messages
General Error Messages of System
Indicates that the server requires the client that had
attempted to bind anonymously or without supplying
credentials to provide some form of credentials.
1516
LDAP INVALID CREDENTIALS
Indicates that the provided credentials (e.g., the user's
name and password) are invalid.
1517
LDAP INSUFFICIENT ACCESS
Indicates that the client does not have sufficient access
rights to perform the operation.
1518
LDAP BUSY
Indicates that the server is too busy to service the
operation.
1519
LDAP UNAVAILABLE
Indicates that the server is shutting down or a subsystem
necessary to complete the operation is offline.
1520
LDAP UNWILLING TO PERFORM
Indicates that the server is unwilling to perform the
operation.
1521
LDAP LOOP DETECT
Indicates that the server has detected an internal loop
(e.g., while dereferencing aliases or chaining an
operation).
1522
LDAP NAMING VIOLATION
Indicates that the entry's name violates naming
restrictions.
1523
LDAP OBJECT CLASS VIOLATION
Indicates that the entry violates object class restrictions.
1524
LDAP NOT ALLOWED ON NONLEAF
Indicates that the operation is inappropriately acting upon
a non-leaf entry.
1525
LDAP NOT ALLOWED ON RDN
Indicates that the operation is inappropriately attempting to
remove a value that forms the entry's relative distinguished
name.
1526
150
LDAP ALREADY EXISTS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Indicates that the request cannot be fulfilled (added,
moved, or renamed) as the target entry already exists.
1527
LDAP NO OBJECT CLASS MODS
Indicates that an attempt to modify the object class(es) of
an entry's 'objectClass' attribute is prohibited. For example,
this code is returned when a client attempts to modify the
structural object class of an entry.
1528
LDAP RESULTS TOO LARGE
Results are too large.
1529
LDAP AFFECTS MULTIPLE DSAS
Indicates that the operation cannot be performed as it
would affect multiple servers (DSAs).
1530
LDAP OTHER
Indicates that the server has encountered an internal error.
1531
LDAP SERVER DOWN
The LDAP library cannot contact the LDAP server.
1532
LDAP LOCAL ERROR
Some local error occurred.
1533
LDAP ENCODING ERROR
An error was encountered while encoding parameters to
be sent to the LDAP server.
1534
LDAP DECODING ERROR
An error was encountered while decoding a result from the
LDAP server.
1535
LDAP TIMEOUT
A time limit was exceeded while waiting for a result.
1536
LDAP AUTH UNKNOWN
The authentication method specified to ldap_bind() is not
known.
1537
LDAP FILTER ERROR
An invalid filter was supplied to ldap_search() (e.g.,
unbalanced parentheses).
1538
LDAP USER CANCELLED
User cancelled the operation.
Issue: 30-0
DN987378
151
Error messages
General Error Messages of System
1539
LDAP PARAM ERROR
An LDAP routine was called with a bad parameter.
1540
LDAP NO MEMORY
A memory allocation (e.g., malloc or other dynamic
memory allocator) call failed in an LDAP library routine.
1541
LDAP CONNECT ERROR
Connection error.
1542
LDAP NOT SUPPORTED
Indicates that the routine was called in a manner that is not
supported by the library.
1543
LDAP CONTROL NOT FOUND
Indicates that the control provided is unknown to the client
library.
1544
LDAP NO RESULTS RETURNED
Indicates that no results were returned.
1545
LDAP MORE RESULTS TO RETURN
Indicates that more results could be returned.
1546
LDAP CLIENT LOOP
Indicates that the library has detected a loop in its
processing.
1547
LDAP REFERRAL LIMIT EXCEEDED
Indicates the referral limit has exceeded.
1548
LDAP UNKNOWN ERROR CODE
LDAP Server or API returned an error code that is not
recognized.
1549
LDAP IP ADDRESS NOT FOUND
Attribute ipHostNumber is not found from LDAP server's
configuration data entry.
1550
LDAP PORT NOT FOUND
Attribute ipServicePort is not found from LDAP server's
configuration data entry.
1551
LDAP BASE ENTRY NOT FOUND
Attribute ruibaseDN is not found from LDAP server's
configuration data entry.
152
DN987378
Issue: 30-0
General Error Messages of System
1552
Error messages
LDAP USER ENTRY NOT FOUND
Attribute ruiuserDN is not found from LDAP server's
configuration data entry.
1553
LDAP NE TYPE ENTRY NOT FOUND
Attribute ruiNETypeRootDn is not found from LDAP
server's configuration data entry.
1554
LDAP ACL PATH NOT FOUND
Attribute ruiACLSetDn is not found from LDAP server's
configuration data entry.
1555
LDAP ROLE PATH NOT FOUND
Attribute ruiRoleSetDN is not found from LDAP server's
configuration data entry.
1556
LDAP ROLE ST PATH NOT FOUND
Attribute ruiRoleStereoTypeSetDn is not found from LDAP
server's configuration data entry.
1557
PREBTS OBJECT ALREADY EXISTS IN THE DATABASE
FOR THE GIVEN PREBTS ID
PREBTS object already exists in the database for the
given PREBTS id.
1558
CPU OVERLOAD
CPU overload
1559
NO SUCH SERVICE TYPE EXISTS
No such service type exists.
1560
NOT ENOUGH RESOURCE
Not enough resource
1561
SERVICE ID IS EXHAUSTED
Service ID is exhausted.
1562
WRONG CELL HOME INFO
Wrong cell home info
1563
ALL BCF OF PACKET ABIS BCF GROUP HAS TO BE
CONFIGURED TO THE SAME ETP.
ALL BCF OF PACKET ABIS BCF GROUP HAS TO BE
CONFIGURED TO THE SAME ETP.
Issue: 30-0
DN987378
153
Error messages
General Error Messages of System
1564
FILE FOR LAWFUL INTERCEPTION CANNOT BE
FOUND IN CORRECT SUBDIRECTORY.
FILE FOR LAWFUL INTERCEPTION CANNOT BE
FOUND IN CORRECT SUBDIRECTORY.
1565
FILE FOR LAWFUL INTERCEPTION CANNOT BE READ.
FILE FOR LAWFUL INTERCEPTION CANNOT BE READ.
1566
SHARED SECRET KEY NOT FOUND.
SHARED SECRET KEY NOT FOUND.
1567
CCP1D-A CARD NOT FOUND IN ICSU UNIT.
CCP1D-A CARD NOT FOUND IN ICSU UNIT.
1568
CCP1D-A CARD NOT FOUND IN RSMU UNIT.
CCP1D-A CARD NOT FOUND IN RSMU UNIT.
1569
SFP MODULE MISSING
SFP module is missing.
1570
SFP MODULE MISMATCH
SFP module mismatch
1571
HORIZON BTS DOES NOT SUPPORT BB-HOPPING
WITH EGENA
It is not possible to use both EGENA and BB-hopping at
the same time in the BTS.
1572
GIVEN PORT WAS OUT OF RANGE FOR
SEMIPERMANENT CONNECTION
Given port was out of range for semipermanent
connection.
1573
INCORRECT SUM OF WEIGHTS FOR PCU POOL
SELECTION ALGORITHM
The sum of neighbor amount weight, MS amount weight
and PS traffic load weight must always be 100.
1574
DYNAMIC PCU2 POOLING_FEATURE IS NOT IN USE IN
BSC
Dynamic PCU2 pooling feature cannot be enabled due to
that there is no license installed in BSC or the license is
expired or the license is in OFF/CONF state.
1575
154
HIGH LOAD IN MCMU UNIT
DN987378
Issue: 30-0
General Error Messages of System
Error messages
MCMU unit has high load situation and requested
operation was aborted.
1576
PCU POOLING NOT STARTED
PCU pooling operation is not started due to missing cell
load information or missing traffic flow information.
1577
ETHERNET OAM DISCOVERY PROCESS LINK
TIMEOUT
Ethernet OAM discovery process link timeout.
1578
THE MESSAGING MEDIA CANNOT BE RELIABLY
USED. UNIT OPERATES BY ITSELF, SEPARATED
FROM REST OF THE SYSTEM.
THE MESSAGING MEDIA CANNOT BE RELIABLY
USED, UNIT HAS BEEN SEPARATED FROM IT. UNIT
OPERATES BY ITSELF, SEPARATED FROM REST OF
THE SYSTEM.
1579
MOUNT FAILURE ON ACTIVE FLASH
Mount failure on active flash
1580
MOUNT FAILURE ON STANDBY FLASH
Mount failure on standby flash
1581
UNMOUNT FAILURE ON ACTIVE FLASH
Unmount failure on active flash
1582
UNMOUNT FAILURE ON STANDBY FLASH
Unmount failure on standby flash
1583
INCORRECT DESTINATION FAMILY
Incorrect destination family
1584
CARRIER B CANNOT BE PREF BCCH TRX IN EDGE
POWER MODE
Carrier B cannot be preferred marked BCCH TRX if Carrier
A is configured as EDGE POWER mode.
1585
BOTH CARRIER A AND CARRIER B TRXS SHOULD BE
LOCKED
Associated TRX parameters can be modified when both
TRXs are in locked state.
1586
Issue: 30-0
CARRIER B CANNOT BE GTRX WHEN EDGE-POWER
IS USED
DN987378
155
Error messages
General Error Messages of System
GTRX parameter cannot be enabled for Carrier B TRX if
Horizon EDGE Service type of Carrier A TRX is EDGEPOWER.
1587
CARRIER B CANNOT BE GTRX WHEN EDGECAPACITY IS USED IN BTS
GTRX parameter cannot be enabled for Carrier B TRX if
Horizon EDGE Service type of Carrier A TRX is EDGE
CAPACITY and both TRXs are in the same BTS.
1588
ONLY THE ASSOCIATED TRX CAN USE THE SAME
EDAP
When TRX has been defined as Associated TRX with
some other TRX, only the Associated TRX can use the
same EDAP.
1589
ONLY CARRIER A TRX CAN BE IN THE SAME EDAP
THAN THE ASSOCIATED TRX
When TRX has been defined as Associated TRX with
some other TRX, only the Associated TRX can use the
same EDAP.
1590
TOO MANY TRXS IN THE SAME EDAP
The maximum TRX count in EDAP is 4 when BTS site type
in Horizon and Assosiated TRX is MULTI.
1591
ONLY ONE SINGLE TRX CAN BE IN EDAP
When Associated TRX is None, only 1 TRX can be in the
EDAP.
1592
MULTIPLEXED TRXSIG LINKS OF ASSOCIATED TRXS
MUST BE ON SAME PHYSICAL LINK
When associated TRXs has been defined the
MULTIPLEXED TRXSIG channels for TRXs are to be
placed on the same physical 64k link
1593
MAX 4 LAPD IS ALLOWED ON ONE PHYSICAL LINK
FOR HORIZON
Max 4 logical LAPD links are allowed on one physical link
1594
ONLY 64K PHYSICAL LINKS ARE ALLOWED FOR
HORIZON
Only 64k physical links are allowed for Horizon BTS
1595
156
EDGE CARRIER A SHALL BE ASSOSIATED WITH
ASYMMETRIC EDGE TYPE CARRIER B
DN987378
Issue: 30-0
General Error Messages of System
Error messages
If Horizon EDGE service type is EDGE-ASYMMETRIC it
must be checked that TRX is Carrier B and Horizon Edge
Service Type of Carrier A TRX is EDGE
1596
HORIZON EDGE SERVICE TYPE OF CARRIER B
CANNOT BE EDGE
Horizon EDGE service type cannot be EDGE for Carrier B
TRX
1597
ONLY HORIZON EDGE SERVICE TYPE OF CARRIER A
CAN BE EDGE-POWER
If Horizon EDGE service type is EDGE-POWER it must be
checked that TRX is Carrier A
1598
GTRX PARAMETER OF CARRIER B MUST BE
DISABLED WHEN EDGE-POWER IS USED
If Horizon EDGE service type is EDGE-POWER it must be
checked that GTRX parameter of Carrier B TRX must be N
1599
HORIZON EDGE SERVICE TYPE OF CARRIER B MUST
BE NON-EDGE WHEN EDGE-POWER IS USED
If Horizon EDGE service type is EDGE-POWER it must be
checked that Horizon EDGE service type parameter of
Carrier B TRX must be Non-EDGE
1600
ONLY HORIZON EDGE SERVICE TYPE OF CARRIER A
CAN BE EDGE-CAPACITY
If Horizon EDGE service type is EDGE-CAPACITY it must
be checked that TRX is Carrier A
1601
GTRX OF CARRIER B MUST BE DISABLED WHEN
EDGE-CAPACITY IS USED IN SAME BTS
If Horizon EDGE service type is EDGE-CAPACITY it must
be checked that GTRX parameter of Carrier B TRX must
be N if it is under the same BTS
1602
HORIZON EDGE SERVICE TYPE OF CARRIER B MUST
BE NON-EDGE WHEN EDGE-CAPACITY IS USED IN
BTS
If Horizon EDGE service type is EDGE-CAPACITY it must
be checked that Horizon EDGE service type parameter of
Carrier B TRX must be Non-EDGE if it is under the same
BTS
1603
Issue: 30-0
EDGE ENABLING GTRX OF CARRIER B MUST BE
DISABLED WHEN EDGE-CAPACITY IS USED
DN987378
157
Error messages
General Error Messages of System
If Horizon EDGE service type is EDGE-CAPACITY it must
be checked that If Carrier B TRX is under different BTS
object then GTRX must be N if EGENA is enabled in the
other BTS
1604
HORIZON BTS DOES NOT SUPPORT BB-HOPPING IN
EDGE POWER MODE
If Carrier B TRX is under the different BTS object than
Carrier A BSC O&M shall not allow Baseband Hopping in
the BTS of Carrier B if it is paired with a Carrier A which
has the
1605
ONLY CARRIER A CAN HAVE ASSOCIATED TRX ID
Associated TRX id Parameter can be given only for Carrier
A TRX
1606
ASSOCIATION TRX ID NOT FOUND
For Carrier A TRX Horizon TRX Association ID TRX must
be found from database
1607
ASSOCIATED TRX NOT CARRIER B TRX
Horizon TRX Type of Horizon TRX Association ID TRX
must be set as Carrier B
1608
TRX ALREADY ASSOCIATED WITH ANOTHER TRX
The same Horizon TRX Association ID can be used only in
one TRX
1609
CARRIER B NOT USED BY ANY CARRIER A
TRX id of Carrier B must be found from one and only one
Horizon TRX Association ID TRX parameter of Carrier A
TRX and TRX must be in the database
1610
Type of cell home is invalid.
Type of cell home is invalid.
1611
ASSOCIATED TRX IS NOT IN SAME SEGMENT
Horizon TRX Association ID TRX must be in the same
segment than Carrier A TRX
1612
COMMON LICENSE MANAGEMENT SERVER IS
UNREACHABLE
The Common License Management Server is
unreachable. The client is not able to query or modify
license information.
1613
158
CPU OVERLOAD LIMIT EXCEEDED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
CPU overload limit exceeded.
1614
THE WAC OBJECT HAS ALREADY BEEN CREATED IN
THE RADIO NETWORK DATABASE
The WAC object has already been created in the Radio
Network Database.
1615
THERE IS NO ROOM FOR A NEW WAC IN THE RADIO
NETWORK DATABASE
There is no room for a new WAC in the Radio Network
Database.
1616
THE WAC OBJECT COULD NOT BE FOUND IN THE
RADIO NETWORK DATABASE
The WAC object could not be found in the Radio Network
Database.
1617
WAC with existing cell association(s) cannot be deleted
WAC with existing cell association(s) cannot be deleted.
1618
UNKNOWN PARAMETER FOR WAC IN RNW PLAN
Unknown parameter for WAC in RNW Plan
1619
THE STARTING UDP PORT WAS HIGHER THAN
MAXIMUM PORT
The starting UDP port was higher than maximum port. The
starting port should be lower or same as a maximum port
value.
1620
CONFLICT BETWEEN EXISTING BSAC ROLES.
CONFLICT BETWEEN EXISTING BSAC ROLES.
1621
SYNCHRONISATION CABLES BETWEEN BCN ARE
NOT FULLY CHAINED. CABLING CONFIGURATION IS
NEEDED IN HCM.
Synchronization cables between BCN are not fully
connected. This error code informs the operator that
cables should be configured in HCM before further
operation.
1622
SYNCHRONISATION CABLING BETWEEN BCN IS NOT
CORRECTLY CONFIGURED.
Synchronization cabling between BCN is not correctly
configured. This error code informs the operator that
cabling should be correctly configured in HCM before
further operation.
1623
Issue: 30-0
BSAC ROLE DOES NOT EXIST.
DN987378
159
Error messages
General Error Messages of System
BSAC ROLE DOES NOT EXIST.
1624
WAC IS STILL BEING USED BY THE VCEL
WAC IS STILL BEING USED BY THE VCEL.
1625
MCPA FEATURE WILL BE IN USE ONLY IF THE
FEATURE IS CONFIGURED ON BTS SITE
MCPA feature will be in use only if the feature is configured
in BTS site.
1626
MCPA POWER POOLING LICENCE NOT IN USE
MCPA Power Pooling feature license is not in ON or CONF
state.
1627
MCPA POWER POOLING CAPACITY LICENSE
EXCEEDED
MCPA Power Pooling capacity license is exceeded.
1628
BTS WILL START AN ALARM AND THE BCF WILL BE
BLOCKED IF THE MCPA FEATURE IS ENABLED AT BTS
BTS will start an alarm and the BCF will be blocked if the
MCPA feature is enabled at BTS.
1629
PRECISE PAGING FEATURE IS NOT IN USE IN BSC
Precise paging feature is not enabled in BSC. Either
feature license is invalid or the feature is in disabled state.
1630
PRECISE PAGING CAPACITY LICENCE EXCEEDED
Precise paging capacity license exceeded
1631
QOS AWARE ETHERNET SWITCHING FEATURE IS
NOT IN USE IN BSC
Qos aware Ethernet switching feature is not enabled in
BSC. Either the feature license is invalid or the feature is in
disabled state.
1632
QOS AWARE ETHERNET SWITCHING BCF CAPACITY
EXCEEDED
Qos aware ethernet switching BCF capacity license
exceeded
1633
INPUT REFERENCE ID IS ILLEGAL
This code informs the user that the input reference ID is
illegal.
1634
160
ALLOCATING OF HSCF CELL HOME IN LRMPRB
FAILED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Allocating of HSCF cell home in LRMPRB has failed.
1635
ALLOCATING OF HSCF CCH FAILED IN LRMPRB
Allocating of HSCF CCH has failed in LRMPRB.
1636
ALLOCATING OF HSCF RAB FAILED IN LRMPRB
Allocating of HSCF rab has failed in LRMPRB.
1637
CELL HOME NOT FOUND
Cell home is not found.
1638
REMOTE PUBLIC KEYLIST FULL
If the system has stored 10 remote public keys for the sftp
client, adding new remote public keys will cause this error.
1639
HSDPAMAXBITRATEUL MUST BE HIGHER THAN OR
EQUAL TO HSDPAINITIALBITRATEUL
HSDPAMaxBitrateUL must be higher than or equal to
HSDPAinitialBitrateUL.
1640
HSDPAMAXBITRATEUL MUST BE HIGHER THAN OR
EQUAL TO HSDPAMINBRULSTRNRT
HSDPAMaxBitrateUL must be higher than or equal to
HSDPAMinBRULStrNRT.
1641
HSDPAMAXBITRATEUL MUST BE HIGHER THAN OR
EQUAL TO HSDPAINITIALBRULSTRNRT
HSDPAMaxBitrateUL must be higher than or equal to
HSDPAInitialBRULStrNRT.
1642
NO ANSWER RECEIVED FROM CCM IN TIME
No answer is received from ccm in time.
1643
BTS SOFTWARE DOES NOT SUPPORT PACKET ABIS
TRANSPORT MEDIA CONVERSION
BTS SOFTWARE DOES NOT SUPPORT PACKET ABIS
TRANSPORT MEDIA CONVERSION.
1644
INCORRECT ETP UNIT STATE
THE CORRESPONDING ETP UNIT IS IN INCORRECT
STATE FOR THE OPERATION.
1645
DEFERRED DISK ERROR
Data in disk write cache might be lost.
1646
Issue: 30-0
DEFINED ROOT OBJECT IS TOO LONG
DN987378
161
Error messages
General Error Messages of System
Defined root object is too long.
1647
EPS BEARER DOES NOT EXIST EC
EPS bearer does not exist.
1648
EPS BEARER ALREADY EXISTS
EPS bearer already exists.
1649
EPS BEARER LIMIT EXCEEDED
EPS bearer limit exceeded.
1650
CGM=M (MOST FREE) IS NOT ALLOWED TO COEXIST
WITH MGW CONTROLLED CIRCUIT GROUPS.
The CGM=M (most free cgr selection) is not allowed to
coexist with MGW controlled circuit groups.
1651
EOAM LINK ADMIN STATUS IS DISABLE
EOAM LINK ADMIN STATUS IS DISABLE
1652
EOAM LINK IS IN LOCAL LOOPBACK
EOAM LINK IS IN LOCAL LOOPBACK
1653
EOAM LINK IS IN REMOTE LOOPBACK
EOAM LINK IS IN REMOTE LOOPBACK
1654
INTERFACE STATE ON WO UNIT IS UP
INTERFACE STATE ON WO UNIT IS UP
1655
EOAM LINK MODE IS NOT ACTIVE
EOAM LINK MODE IS NOT ACTIVE
1656
ETHERNET LINK IS NOT STABLE
ETHERNET LINK STATE IS NOT STABLE
1657
TOO MANY PCUSIG IN THE SAME GATEWAY UNIT
TOO MANY PCUSIG IN THE SAME GATEWAY UNIT
1658
DTRX IS ALLOWED ONLY FOR SINGLE TYPE TRX
DTRX parameter is only allowed to enable Single type
Horizon TRX.
1659
HORIZON EDGE SERVICE TYPE CANNOT BE NONEDGE WHEN BTS EGPRS AND TRX GPRS ARE
ENABLED
Horizon EDGE service type cannot be non-EDGE if BTS
EGPRS and TRX GPRS are enabled.
162
DN987378
Issue: 30-0
General Error Messages of System
1660
Error messages
SSH WRONG USER NAME AND PASSWORD ERROR
CODE
SSH wrong username and password error code
1661
SSH WRONG IP AND PORT ERROR CODE
SSH wrong IP and port error code
1662
SSH NO SUCH FILE EXISTS IN THE SERVER ERROR
CODE
SSH no such file in the server error code
1663
SSH FILE NAME TOO LONG ERROR CODE
SSH file name too long error code
1664
SSH SERVER AUTHENTICATION ERROR CODE
SSH server authentication error.
1665
GROUP ID WAS NOT FOUND IN GCR DATABASE
Group id was not found in GCR database.
1666
GROUP CALL AREA RECORD WAS NOT FOUND IN
GCR DATABASE
Group call area record was not found in GCR database.
1667
GROUP CALL REFERENCE RECORD WAS NOT
FOUND IN GCR DATABASE
Group call reference record was not found in GCR
database.
1668
IMSI IN REQUEST AND IMSI STORED IN GCR
DATABASE DOES NOT MATCH
IMSI in request and IMSI stored in GCR database does not
match.
1669
CELL LIST WAS NOT FOUND IN GCR DATABASE
Cell list was not found in GCR database.
1670
EXECUTION OF UPDATE REQUEST WILL CAUSE
EXCEEDING OF THE NUMBER OF ALLOWED CELLS IN
THE CELL LIST
Execution of update request will cause exceeding of the
number of allowed cells in the cell list.
1671
CELL IS ALREADY USED BY ANOTHER CELL LIST
Cell is already used by another cell list.
Issue: 30-0
DN987378
163
Error messages
General Error Messages of System
1672
REFERRED CELL WAS NOT FOUND IN GCR
DATABASE
Referred cell was not found in GCR database.
1673
REFERRED CELL LIST IS IN USE AND CANNOT BE
DELETED FROM GCR DATABASE
Referred cell list is in use and cannot be deleted from GCR
database.
1674
RECORD FOR THE GIVEN GROUP CALL AREA CODE
ALREADY EXISTS IN GCR DATABASE
Record for the given group call area code already exists in
GCR database.
1675
REFERRED GROUP CALL AREA IS IN USE AND
CANNOT BE DELETED
Referred group call area is in use and cannot be deleted.
1676
GIVEN GROUP ID ALREADY USED IN GCR DATABASE
Given group ID is already used in GCR database.
1677
EXECUTION OF UPDATE REQUEST WILL CAUSE
OVERLAPPING CELL LISTS IN GCR DATABASE
Execution of update request will cause overlapping cell
lists in GCR database.
1678
GIVEN GROUP CALL REFERENCE ALREADY EXISTS
IN GCR DATABASE
Given group call reference already exists in GCR
database.
1679
GIVEN NAME ALREADY EXISTS IN GCR DATABASE
Given name already exists in GCR database.
1680
GIVEN RECORD ALREADY RESERVED IN GCR
DATABASE
Given record is already reserved in GCR database.
1681
GIVEN GROUP CALL REFERENCE IS INVALID
Given group call reference is invalid.
1682
LMU SOFTWARE DOES NOT SUPPORT DISABLING OF
PARAMETER LMU FNO 26-MULTIPLIER USAGE
LMU software does not support disabling of parameter
LMU FNO 26-multiplier usage.
1683
164
SITE TYPE DOES NOT SUPPORT LMU TSL FN DELAY
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Site type does not support LMU TSL FN delay.
1684
BTS SOFTWARE DOES NOT SUPPORT LMU TSL FN
DELAY
BTS software does not support LMU TSL FN delay.
1685
CSDAP REQUIRED FOR OSC DHR
OSC (Orthogonal Sub Channel) Half Rate feature cannot
operate without CSDAP.
1686
THE NUMBER OF CBC OBJECTS EXCEEDS THE LIMIT
The number of CBC objects must not exceed the
maximum number in RNC.
1687
THE NUMBER OF IUO OBJECTS EXCEEDS THE LIMIT
The maximum number of iuo objects must not exceed the
maximum number in RNC.
1688
ATM BUNDLE WHERE N-CID BELONGS IS CURRENTLY
MOVING FROM A2SP UNIT TO ANOTHER
ATM bundle where N-CID belongs is currently moving from
A2SP unit to another.
1689
NO REMOTE SSH PUBLIC KEYS IN CONFIGURATION
No remote SSH public keys in configuration
1690
REMOVAL OF LAST KEY FORBIDDEN AS LONG AS
SERVER AUTHENTICATION ENABLED
Removal of the last key is forbidden as long as server
authentication is enabled.
1691
BFD DESTINATION IP AND STATIC ROUTE GATEWAY
IP DO NOT MATCH
BFD destination IP and static route gateway IP do not
match.
1692
MGW DOES NOT SUPPORT AIF TDM HUNTING IN
MGW
MGW does not support A interface TDM hunting in MGW.
1693
PDP CONTEXT EXTENSION CANNOT BE CREATED
This error code is used in the HLR when an existing PDP
context cannot be extended with data that requires
additional database record to store. Such data is a second
PDP address in an IPv4v6 dual stack PDP context.
1694
Issue: 30-0
ERROR WHEN INITIALIZING A SOCKET
DN987378
165
Error messages
General Error Messages of System
Error when initializing a socket.
1695
STARTING OF REQUESTED MONITORING HAS FAILED
The starting of requested monitoring has failed.
1696
BCF LOCKED BUT CHILD BTS(S) ARE LEFT TO
LOCKED STATE DUE TO ONGOING FILE BASED PLAN
PROVISIONING
Locking BCF with forced handover via SendToNetwork is
done by first locking child BTS(s) with forced handover,
then locking BCF and finally unlocking child BTS(s). BCF
is locked successfully but child BTS(s) unlocking has failed
due to ongoing file based plan provisioning.
1702
UNIT DOES NOT NEED MODULE LEVEL
REDUNDANCY
Unit does not need module level redundancy.
1703
UNIT TYPE HAS NOT ENOUGH SPEX UNITS, MODULE
LEVEL REDUNDANCY NOT FULFILLED
Unit type has not enough SPEX units, module level
redundancy not fulfilled.
1770
UNIT IN BLOCK STATE
The unit is in the block state.
1776
APS REMOTE MONITOR FAILS
APS remote monitor fails.
1777
APS LOCAL MONITOR FAILS
APS local monitor fails.
1778
APS REMOTE CONTROLLER FAILS
APS remote controller fails.
1779
APS LOCAL CONTROLLER FAILS
APS local controller fails.
1780
TOO MANY ICR PLMN IDS FOR IUO
The XML file processing program block (PABROS, RNC
OMU) has found too many ICR PLMN IDs for IUO.
1781
KEY ADDED EXISTS IN REMOTE KEY LIST
This error only appears when adding a remote public key
to a list when the remote key already exists.
1782
166
REFERRED CELL LIST IS IN USE IN GCR DATABASE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Referred cell list is already in GCR database.
1785
CONGESTION ON CGR
Hunting of circuit from CGR has not succeeded.
1804
THIS RESERVATION IS OBSOLETE AND SHOULD BE
REMOVED
This reservation is obsolete and should be removed.
1818
DSP SERVICE CREATE/MODIFY REQUEST SENT TO
RM3 CONTAINS CELL ID THAT IS NOT IN VALID
RANGE
DSP service create/modify request sent to RM3 contains
cell id that is not in valid range.
1821
THE COSITE OBJECT HAS ALREADY BEEN CREATED
IN THE RADIO NETWORK DATABASE
The COSITE object has already been created in the Radio
Network Database.
1822
THE COSRNC OBJECT HAS ALREADY BEEN CREATED
IN THE RADIO NETWORK DATABASE
The COSRNC object has already been created in the
Radio Network Database.
1823
THERE IS NO ROOM FOR A NEW COSITE IN THE
RADIO NETWORK DATABASE
There is no room for a new COSITE in the Radio Network
Database.
1824
THERE IS NO ROOM FOR A NEW COSRNC IN THE
RADIO NETWORK DATABASE
There is no room for a new COSRNC in the Radio Network
Database.
1825
THE COSITE OBJECT COULD NOT BE FOUND IN THE
RADIO NETWORK DATABASE
The COSITE object could not be found in the Radio
Network Database.
1826
THE COSRNC OBJECT COULD NOT BE FOUND IN THE
RADIO NETWORK DATABASE
The COSRNC object could not be found in the Radio
Network Database.
1827
Issue: 30-0
THE COSITE OBJECT CAN CO-EXIST WITH ONLY RNC
OBJECT WITHOUT ANY OF ITS SUB-OBJECTS IN
RADIO NETWORK DATABASE
DN987378
167
Error messages
General Error Messages of System
The COSITE object can co-exist with only RNC object
without any of its sub-objects in Radio Network Database.
1841
THE CHECKSUM OF VRNC DATA IS DIFFERENT FROM
THAT STORED IN THE DATABASE FILE
The checksum of VRNC data is different from that stored in
VRNC record, which means the data of VRNC is modified
in an illegal way, it\'s better to delete the corresponding
VRNC and configure it again.
1842
RNW DB READ CALL TO CRNC DATABASE FAILED AS
CO-SITING IS NOT READY
RNW DB read call to cRNC database failed as co-siting is
not ready either due to cluster interface failure or software
compatibility error.
1855
C0SMAN DID NOT RECEIVE ACKNOWLEDGEMENT
MESSAGE FROM L2TMAN
C0SMAN did not receive acknowledgement message from
L2TMAN.
1856
C0SMAN DID NOT RECEIVE ACKNOWLEDGEMENT
MESSAGE FROM IRPMAN
C0SMAN did not receive acknowledgement message from
IRPMAN.
1874
ETHERNET OAM SUPPORT FEATURE IS NOT IN USE
IN BSC
Ethernet OAM Support feature license is not enabled in
BSC.
1893
STATE OF VRNC IS NOT WO-EX
The state of VRNC is not WO-EX.
1894
TDM QUEUING CANCELLED IN CALL MANAGEMENT
TDM queuing cancelled in call management.
1895
TDM QUEUING STOPPED BY CALL MANAGEMENT
TDM queuing stopped by call management.
1896
TDM QUEUING FOR LEG CANNOT BE STARTED AS
TDM QUEUE TABLE IS FULL
TDM queue table is full, so TDM queuing for leg cannot be
started.
1897
168
TDM QUEUING FOR LEG CANNOT BE STARTED AS
TDM CIRCUIT GROUP RELATED QUEUE TABLE IS
FULL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
TDM Circuit Group related queue table is full, so TDM
queuing for leg cannot be started.
1898
TDM QUEUING STARTED FOR LEG
TDM queuing started for leg.
1899
TDM QUEUED ITEM NOT FOUND FROM THE QUEUE
TDM queued item is not found from the queue.
1902
CIRCUIT GROUP STATE PREVENTS TDM QUEUING
REQUEST
Circuit Group state prevents TDM queuing request.
1903
CIRCUIT STATE PREVENTS TDM QUEUING REQUEST,
THERE ARE NO WO-EX STATE CIRCUITS UNDER
CIRCUIT GROUP
Circuit state prevents TDM queuing request. There are no
WO-EX state Circuits under Circuit group.
1904
CIRCUIT GROUP STATE PREVENT TDM QUEUING
REQUEST, CIRCUIT GROUP STATE IS NOT WO-EX
Circuit Group state prevent TDM queuing request. Circuit
Group state is not WO-EX.
1924
CANNOT CHANGE VRNC STATE TO SE WITHOUT FCD
OPTION WHEN COSRNC ADMIN STATE IS UNLOCKED
Cannot change VRNC state to SE without FCD option
when COSRNC admin state is unlocked.
1937
INCOMPATIBLE VERSION OF L2L2 MANAGER
BETWEEN CRNC AND MCRNC
Incompatible version of L2L2 manager between cRNC and
mcRNC
1938
NOT SUPPORTED IP CONFIGURATION BY L2L2
MANAGER IN CO-SITING
Not supported IP configuration by L2L2 manager in cositing
1939
NUMBER OF PROBLEMATIC L2L2 TUNNELS BETWEEN
CRNC DSP AND MCRNC *UP EXCEEDS A THRESHOLD
The number of problematic L2L2 tunnels between cRNC
DSP and mcRNC *UP exceeds a threshold.
1945
Issue: 30-0
VALUE OF PSCONVMINRSCPTHRE WILL ALWAYS BE
LOWER THAN OR EQUAL TO VALUE OF
CPICHRSCPTHRESRBHSDPA
DN987378
169
Error messages
General Error Messages of System
Value of PSConvMinRSCPThre will always be lower than
or equal to value of CPICHRSCPThreSRBHSDPA.
1949
WCEL-PSCONVENABLED CAN BE ENABLED ONLY
WHEN FRACTIONAL DPCH (WCEL-FDPCHENABLED)
IS ENABLED
WCEL-PSCONVENABLED can be enabled only when
fractional DPCH (WCEL-FDPCHENABLED) is enabled.
2006
MAXIMUM NUMBER OF ADJGS INCLUDED IN SYS
INFO IS EXCEEDED
Maximum number of ADJGs included in SYS INFO is
exceeded.
2007
WBTS-IUBTRANSPORTSHARING PARAMETER CAN BE
ENABLED ONLY WHEN WBTS-IUBTRANSPORTMEDIA
IS SET AS IP IUB
WBTS-IubTransportSharing parameter can be enabled
only when WBTS-IubTransportMedia is set as IP Iub.
2008
WHEN IUBTRANSPORTSHARING IS ENABLED, TQM
IDS DEFINED IN WBTS OBJECT MUST HAVE UNIQUE
VALUE OTHER THAN ZERO.
When IubTransportSharing is Enabled, TQM IDs defined in
WBTS object must have unique value other than zero.
2009
WHEN IUBTRANSPORTSHARING IS ENABLED,
IPBASEDROUTEIDS DEFINED IN WBTS MUST HAVE
UNIQUE VALUE OTHER THAN ZERO.
When IubTransportSharing is Enabled, IPBasedRouteIDs
defined in WBTS must have unique value other than zero.
2010
WBTS- IUBTRANSPORTSHARING PARAMETER CAN
BE ENABLED ONLY WHEN WBTS - HSDPACCENABLED
IS SET AS DISABLED.
WBTS- IubTransportSharing parameter can be enabled
only when WBTS-HSDPACCEnabled is set as Disabled.
2014
THE FILE DOES NOT EXIST IN THE CURRENT
VERSION OF MEFILE BUT IN THE OTHER VERSION
In ssu, mfsprb in a specific unit receives message
load_one_file_s. The file does not exist in the current
version of MEFILE, but exists in the other version MEFILE.
This loading request will fail with this error code.
2031
A MEMORY FILE IS NOT DEFINED IN A SPECIFIC UNIT
A memory file is not defined in a specific unit.
170
DN987378
Issue: 30-0
General Error Messages of System
2032
Error messages
IP SUBNET MUST BE UNIQUE FOR EACH IUCSIP
OBJECT RELATED TO THE SAME IUCS INSTANCE
IP subnet must be unique for each IUCSIP object related
to the same IUCS instance.
2033
IP SUBNET MUST BE UNIQUE FOR EACH IUPSIP
OBJECT RELATED TO THE SAME IUPS INSTANCE
IP subnet must be unique for each IUPSIP object related
to the same IUPS instance.
2036
ADX IS NOT CONFIGURED
ADX is not configured.
2040
MODIFYING PROTECTION GROUP PARAMETERS
FAILED
Modifying protection group parameters failed.
2041
PARAMETER ROLLBACK FAILED
Parameter rollback failed.
2042
CAC REQUEST IS REJECTED DUE TO LACK OF
BANDWIDTH IN COSITING CONFIGURATION, A RETRY
COULD BE MADE LATER
In cositing configuration, LGMANA or CACPRB will return
this error code for RM2 to have a retry after it gets more
bandwidth share from the peer side.
2043
UNSUPPORTED SITE TYPE FOR REMOTE CSDAP
Remote CSDAP is not supported for the given BTS site
type.
2045
CURRENT COMBINATION OF SWITCHES IS NOT
SUPPORTED
The combination of switches currently created to hardware
configuration management database is not supported by
LAN device integration features. Please refer to user
documentation to find supported hardware.
2046
THE NUMBER OF IUIP OBJECTS EXCEEDS THE LIMIT
The number of IUIP objects must not exceed the maximum
number in the RNC.
2048
Issue: 30-0
IF WCEL-TARGFREQLOWER HAS VALUE 0, WCELTARGFREQUPPER CANNOT BE CHANGED TO VALUE
GREATER THAN 0
DN987378
171
Error messages
General Error Messages of System
If WCEL-TargFreqLower has a value of 0, WCELTargFreqUpper cannot be changed to a value greater than
0.
2049
SUBSCRIBER IN LINE BLOCKED STATE
The subscriber line measured has been in the line blocked
state during measurement. This is not necessarily a fault
condition. The line blocked state may occur when the
subscriber is in the OFF_HOOK state without dialing for a
certain period of time. In this case the line loop resistance
is given as the insulation resistance between a and b
conductors.
2050
LTEST UNIT BUSY
The LTEST unit with which the subscriber line should be
measured is reserved for another measurement. Try again
after a while. If a subscriber line is connected via the
LTEST unit to an external measuring device, the
connection must be released before the LTEST unit can be
used for any other measurements.
2051
LTEST UNIT FAULTY
The LTEST unit with which the subscriber line should be
measured is faulty according to the working condition test.
Replace the LTEST unit. See alarm listing for the
corresponding ** alarm and check its meaning in
Disturbance Print-Outs, Alarm Print-Out Manual, 2.5/ the
corresponding alarm. Repeat the measurement after 10
minutes from the replacement of the plug-in unit.
2052
NO LTEST UNIT DEFINED FOR GIVEN SUBSCRIBER
The LTEST unit with which the subscriber line should be
measured is not defined. Check from the LTSUBR file of
the OMU which LTEST unit is defined for the measurement
of the lines of the subscriber module (SUB). If the module
is not mentioned in the file, add the corresponding record
defining the LTEST unit and the LTEST group. (Use
command DFS). If LTSUBR already contains the record,
check from the LTCONF file of the OMU whether
configuration data have been defined for the LTEST unit. If
there are no configuration data, add them by using the
DFS command (if the LTEST unit really is included in the
system). After the file modifications, repeat the
measurement attempt.
2053
SUBSCRIBER IN BUSY STATE
Subscriber line to be measured is in busy state. Try again
after a while.
2054
172
RINGING GROUP IN BUSY STATE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The ringing group that contains the subscriber line to be
measured is in busy state. Try again after a while.
2055
WCEL-TARGFREQUPPER CANNOT HAVE EQUAL OR
LOWER VALUE THAN WCEL-TARGFREQLOWER
(EXCEPT 0)
WCEL-TargFreqUpper cannot have an equal or lower
value than WCEL-TargFreqLower (except 0).
2056
TEST LINE OF LTEST IN USE
Test line of the LTEST unit with which the subscriber line
should be measured is reserved for another test. Try again
after a while.
2057
SSP CONNECTION FAILURE DURING TEST
The connection to the subscriber module to which the
subscriber line is connected is not functioning. This is
usually a temporary failure. Try again after a while.
2058
LTEST CONNECTION FAILURE DURING TEST
The connection to the LTEST plug-in unit on which the
subscriber line should be measured is not functioning. This
is usually a temporary failure. Try again after a while.
2061
SUBSCRIBER CALLED DURING TEST
The subscriber line to be measured received a call during
test. Try again after a while.
2062
RINGING GROUP CALL INTERRUPTION
The ringing group to which the subscriber line to be
measured belongs received a call during test. Try again
after a while.
2063
TIME-OUT OF TEST SUPERVISION IN SUBSCRIBER
MODULE
In the SUB to which the subscriber line to be measured
belongs, the time limit of testing expired. Try again after a
while.
2064
TIME-OUT OF LTEST CONNECTION SUPERVISION
The testing time limit of the program block controlling the
measurement channel forming the LTEST connection
expired during test. Try again after a while.
2065
SWITCHOVER IN SUBSCRIBER STAGE DURING TEST
In the subscriber stage to which the subscriber line to be
measured belongs, there was a switchover during test. Try
again after a while.
Issue: 30-0
DN987378
173
Error messages
General Error Messages of System
2067
INVALID POSITION NUMBER
The position number with which the subscriber line to be
measured was identified is incorrect.
2068
THE NUMBER OF ADJG OBJECTS EXCEEDS THE
LIMIT
The number of ADJG objects must not exceed the
maximum number in the WCEL.
2069
FILE ERROR DETECTED BY LITEST PROGRAM BLOCK
There is no room in the working files of the LITEST
program block, or the program block has detected another
error in the files. Try again after a while. If the result still is
the same, restart LITEST.
2070
LINE TEST OVERLOAD
All the ASS channels in the OMU, that are in the use of
LITEST, are already in use which means that a new
measurement can not be started. Try again after a while.
2071
TEST LINE OF LTEST UNIT BLOCKED FOR TEST
PURPOSES
The test line of the LTEST plug-in unit on which the
subscriber line should be measured, is temporarily blocked
from testing. Try again after a while.
2072
INSUFFICIENT INSULATION ON LINE
An very small insulation resistance has been detected on
the subscriber line that has been measured. Repeat the
measurement. If the result still is the same, there is an
insulation fault on the line in question, and it must be
repaired with other methods.
2073
MODULE INQUIRY FAILURE
The inquiry of subscriber module data from the central
memory (CM) has failed. This may be caused by an error
in the files of the CM or OMU, or by a communication
failure between these units. Try again after a while. If the
measurement fails again, check the LTCONF file in the
OMU. If it is in order, check whether all the subscriber
modules determined as locations of the LTEST plug-in unit
have been taken into account in the ASCHAN, MODULE
and MDROUT files.
2074
LTMANA TEST INTERRUPT
The measurement is interrupted due to time-out in the
control of test unit and test line usage. Try again after a
while.
174
DN987378
Issue: 30-0
General Error Messages of System
2075
Error messages
WCEL- HSFACHDRXENABLED CAN BE ENABLED
ONLY WHEN HSRACHENABLED IS ENABLED.
The WCEL- HSFACHDRXENABLED can be enabled only
when HSRACHENABLED is enabled.
2076
TEST LINE BUSY
The test line is busy. Try again after a while.
2077
TEST LINE RESERVATION FAILURE
The reservation of test line for measurement has failed. Try
again after a while.
2078
QUEUEING FOR TEST EQUIPMENT
The measurement is queuing for test equipment. Try again
after a while.
2080
HHOMARGINPEAKECNO MUST BE GREATER THAN
OR EQUAL TO HHOMARGINAVERAGEECNO.
HHOMarginPeakEcNo must be greater than or equal to
HHOMarginAverageEcNo.
2081
LOADCONTROLPERIODPS VALUE SHOULD NOT BE
SMALLER THAN THE VALUE OF SCHEDULINGPERIOD
The value of LoadControlPeriodPS should not be smaller
than the value of SchedulingPeriod.
2082
IUR-APPAWARERANENABLED PARAMETER CAN BE
ENABLED ONLY WHEN IUR-HSPAOVERIUR IS SET AS
ENABLED.
The IUR-AppAwareRANEnabled parameter can be
enabled only when IUR-HSPAOverIur is set as enabled.
2083
WCEL-APPAWARERANENABLED PARAMETER CAN BE
ENABLED ONLY WHEN WCEL-HSDPAENABLED IS SET
AS ENABLED.
WCEL-AppAwareRANEnabled parameter can be enabled
only when WCEL-HSDPAenabled is set as enabled.
2085
DSCP CODE MUST BE UNIQUE WITHIN APPLICATION
GROUP AND BETWEEN APPLICATION GROUPS.
DSCP code must be unique within Application Group and
between Application Groups.
2087
Issue: 30-0
WCEL-APPAWARERANENABLED MUST HAVE THE
SAME VALUE IN BOTH CELLS OF THE DC HSDPA
CELL PAIR.
DN987378
175
Error messages
General Error Messages of System
WCEL-AppAwareRANEnabled must have the same value
in both cells of the DC HSDPA cell pair.
2089
RELEASEMARGINPEAKECNO MUST BE GREATER
THAN OR EQUAL TO
RELEASEMARGINAVERAGEECNO.
ReleaseMarginPeakEcNo must be greater than or equal to
ReleaseMarginAverageEcNo.
2104
WAC-TRAFVOLPENDINGTIMEDL SHOULD BE
SMALLER THAN RNHSPAUPRESALLOCINCELLDCHWAIT.
WAC-TrafVolPendingTimeDL should be less than
RNHSPA-UPResAllocInCellDCHWait.
2105
WAC-TRAFVOLPENDINGTIMEUL SHOULD BE
SMALLER THAN RNHSPAUPRESALLOCINCELLDCHWAIT.
WAC-TrafVolPendingTimeUL should be less than
RNHSPA-UPResAllocInCellDCHWait.
2106
IF IUR-HSPAOVERIUR IS ENABLED IURIURUPSUPPORT MUST BE ENABLED.
If IUR-HSPAOverIur is enabled, then the IURIurUPSupport must be enabled.
2107
IUO OBJECT COUNT MUST NOT EXCEED 4 IF MOCN
OR MORAN IS CONFIGURED
The IUO object count must not exceed 4 if MOCN or
MORAN is configured.
2108
IF RNC IS CONNECTED TO PRIMARY OMS THEN RNCSERVINGOMSADMINSETTING IS NOT ALLOWED TO
SET TO SECONDARY FORCED
If RNC is connected to the primary OMS then RNCServingOMSAdminSetting is not allowed to set to
SECONDARY FORCED.
2113
INCORRECT TRE_ID IN LMU AREA WHEN BSS
SYNCHRONIZATION IS IN USE
An incorrect TRE_ID is in use in the LMU Area during BSS
Synchronization. The TRE_ID should have a valid value if
External 1PPS synch source (EXT1PPS) is not enabled for
the BCF.
2114
LMU IS USED AS BTS SYNC SOURCE INSTEAD OF
1PPS
The LMU is used as a BTS sync source instead of 1PPS.
176
DN987378
Issue: 30-0
General Error Messages of System
2116
Error messages
IUBTRANSPORTSHARINGIND PARAMETER MUST
HAVE A UNIQUE VALUE.
The IubTransportSharingInd parameter must have a
unique value.
2117
VSWR ALARM THRESHOLD CANNOT BE MODIFIED
VSWR alarm threshold limits cannot be modified as the
antenna values are not defined.
2118
CONFIGURED ALARM PARAMETER VALUES ARE OUT
OF RANGE
The configured alarm threshold limits are out of range.
2119
VSWR ALARM MAJOR LIMIT SHOULD BE GREATER
THAN MINOR LIMIT
The VSWR alarm\'s major limit should be greater than
VSWR alarm\'s minor limit.
2120
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 0.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 0.
2121
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 1.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 1.
2122
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 2.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 2.
2123
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 3.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 3.
2124
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 4.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 4.
2125
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 5.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 5.
Issue: 30-0
DN987378
177
Error messages
General Error Messages of System
2127
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 6.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 6.
2128
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 7.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 7.
2129
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 8.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 8.
2130
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 9.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 9.
2132
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 11.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 11.
2133
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN DOWNLINK IS DEFINED FOR INITIAL SPI 12.
The Target SPI can have NBR value defined only if NBR in
downlink is defined for Initial SPI 12.
2134
IMSI TRACE ENHANCEMENTS FEATURE LICENSE
NOT ENABLED IN BSC
IMSI Trace enhancements feature license is not enabled in
BSC.
2135
VMATMP FILE CORRUPTED
Check is the VMATMP file is corrupted.
2136
VMATMP FILE READING FAILED
This means that reading the VMATMP file failed.
2137
CONFIGURATION FILE WRITING FAILED
This means that writing of the configuration file has failed.
2139
Local Cell is not Dual Band Capable
The Local Cell is not Dual-Band-Capable.
178
DN987378
Issue: 30-0
General Error Messages of System
2140
Error messages
STANDBY BTS ALREADY EXIST IN SEGMENT
The segment can have only one standby BTS. There is
one standby BTS already existing in the segment.
2141
STANDBY BTS AND BCCH BTS CANNOT CONFIGURE
UNDER SAME BCF
Standby BTS and BCCH BTS cannot be configured under
the same BCF.
2142
BCF SITE TYPE OF BCCH BTS AND STANDBY BTS IS
NOT SAME
The BCF site type of BCCH BTS and standby BTS of the
segment should be the same.
2143
INVALID BTS FOR STANDBY TRX
The standby TRX can only be created in BCCH BTS or a
standby BTS of a segment.
2144
STANDBY TRX ALREADY EXIST IN BTS
BCCH BTS can have only one standby TRX. There is one
standby TRX already existing in the BTS.
2145
LESS NUMBER OF TRX IN BCCH BTS THAN STANDBY
BTS
The number of standby TRXs in the standby BTS
exceeded the total number of TRXs in the BCCH BTS of
the segment.
2147
SYNC CHAIN CANNOT BE ENABLED FOR BCF WITH
STANDBY BTS
The BCF on which the standby sector is being created
should not be part of a BCF chain. The BCF should not be
configured as master/slave BCF of a BCF synchronization
chain.
2148
STANDBY TRX ID NOT COMPATIBLE WITH TCC
ENBALED TRXs OF BCCH BTS
The TRX ID of the standby TRX should be odd, and the
next even-numbered TRX after the standby TRX ID should
not exist.
2149
HARD DISK STARTUP IS ONGOING
Hard disk startup is ongoing. The driver hasn\'t been ready
to be accessed. Try again after a while.
2150
Issue: 30-0
COULD NOT DECODE GPB MESSAGE
DN987378
179
Error messages
General Error Messages of System
The RNC Element Manager Server Program Block has
failed in decoding (de-serializing) the Google Protocol
Buffer (GPB) message received.
2151
COULD NOT ENCODE GPB RESPONSE MESSAGE
The RNC Element Manager Server Program Block has
failed in encoding (serializing) the Google Protocol Buffer
(GPB) message from the collected data.
2152
COULD NOT SEND GPB MESSAGE TO CLOSED
SOCKET
The RNC Element Manager Server Program Block has
failed in sending encoded (serialized) Google Protocol
Buffer (GPB) message because the target IP socket is not
open.
2153
RNC INTERNAL RNW DATABASE FOR EM NOT READY
The RNC Element Manager Server Program Block is
updating its internal RNW database data for EM, and thus
cannot serve now.
2154
RNC NOT READY TO SERVE REQUEST
The RNC Element Manager Server Program Block is not
ready to serve the request from the EM. The required hand
process may still be in the starting phase, or the service is
temporarily blocked by some other tasks.
2155
NO RNW DATA TO RETURN
The RNC Element Manager Server Program Block is not
able to return the requested Radio Network data as none
of the requested RNW objects exist.
2157
FAILED TO SYNCHRONIZE TEST LOOP
Failed to synchronize test loop.
2158
TIMESLOT IN USE
Timeslot in use
2161
DYNAMIC ABIS POOL SIZE INVALID
The dynamic Abis pool size is invalid between BSC and
BTS.
2164
INVALID PATH INFORMATION
Failed to set/clear as invalid path information.
2166
INVALID AGC
This means an invalid AGC.
180
DN987378
Issue: 30-0
General Error Messages of System
2167
Error messages
ARFN NOT PASSED IN LOOP TEST COMMAND
This means that the ARFN failed in the Loop Test
command.
2169
RF RESOURCE ALLOCATION TIMEOUT FAILURE
RF resource allocation timeout failure for test
2170
FAILED DUE TO TRX RECONFIGURATION
Failure because of TRX reconfiguration
2171
LOOP TEST ERROR MORE THAN SPECIFIED LIMIT
Loop test error is more than the specified limit.
2172
UNABLE TO MEASURE POWER LEVEL
Unable to measure the power level
2173
RFM RF FAILURE
RFM RF failure
2174
HIGH RF INTERFERENCE
This means high RF interference.
2175
LOW POWER IN ABIS1-AIR3
There is low power in the Abis1-Air3 loop.
2176
UNABLE TO MEASURE RX SENSITIVITY
Unable to measure Rx sensitivity
2177
FAILURE IN BB MODULE
There is failure in BB module.
2178
FAILURE DUE TO FORCED RESET
There is failure due to Forced Reset.
2179
LOOP POINT OPENING/CLOSING FAILED ON
REQUESTED RFM PIPE
Loop point opening/closing failed on the requested RFM
pipe.
2181
ECXX DOES NOT EXIST
ECxx does not exist.
2182
ERXX NOT PRESENT
ERxx is not present.
Issue: 30-0
DN987378
181
Error messages
General Error Messages of System
2183
ERXX/ECXX HW IS NOT VALID OPERATIONAL STATE
ERxx/ECxx HW is not in a valid operational state.
2184
FAILED TO CLEAR AIR LOOP POINT AS TS ALREADY
FREE
Failed to clear air loop point as TS is already free.
2185
FAILURE IN SETTING AIR LOOP POINT
There is failure in setting air loop point as the DDU
synthesizer is not able to achieve Lock state.
2186
FAULTY ERXX HW
There is a faulty ERXX HW.
2187
FIXED TRAFFIC CHANNE DOES NOT EXIST
Fixed traffic channels do not exist.
2188
INVALID STATE OF ERXX
There is an invalid state of Erxx.
2189
LOW BCCH POWER LEVELS
There are low BCCH Power levels.
2190
UNABLE TO SET LOOP POINT ON CONNECTED
DDU/RTC OR ON ABIS WITHIN THE PREDEFINED TIME
Unable to set the loop point on the connected DDU/RTC or
on the Abis within the predefined time.
2191
OMUSIG CAPACITY DOES NOT EXIST
OMUSIG capacity does not exist.
2192
FAILURE IN SETTING AIR LOOP POINT AS ERXX
SYNTHESIZER NOT ABLE TO ACHIEVE LOCK STATE
There is failure in setting the air loop point as the ERxx
synthesizer is unable to achieve Lock state.
2193
RF CABLE MISSING
RF cables missing
2194
RTC NOT IN SUPERVISOTY STATE
RTC not in supervisory state
2195
TEST NOT ALLOWED
Test is not allowed. The controlling CDTRX is in the
antenna hopping/BB hopping sector.
182
DN987378
Issue: 30-0
General Error Messages of System
2196
Error messages
UNSUPPORTED ERXX HW PRESENT
Unsupported ERxx HW present
2197
INVALID TRX ID
This means an invalid TRX ID.
2198
ERXX PHASE LOOP LOCK HAS ALARM ON IT
The ERxx Phase Loop Lock (PLL) has an alarm on it.
2200
TIMEOUT OCCURRED FOR VVA TUNING
Timeout occurred for VVA tuning
2201
TEST CANNOT BE STARTED IN PIPE AS LOOP IS
ALREADY SET
The test can not be started as the loop is already set in the
pipe.
2202
ANOTHER TEST RUNNING
Another test running
2203
TEST NOT RUNNING
The test is not running.
2204
FAILED AS TEST NOT ALLOWED
The test is not allowed.
2205
TIMESLOT BUSY
The timeslot is busy.
2206
RF RESOURCE ALLOCATION FAILURE
RF resource allocation activation failure for test
2207
RF RESOURCE RELEASE FAILURE
RF resource release failure after test
2208
TOO LITTLE POWER
Too little Tx power
2209
TRX LOGICALLY RESET DURING VSWR PROBING
TRX was logically reset during VSWR probing.
2210
NO TRX FOUND IN SUPERVISORY AND UNBLOCKED
STATE
No TRX found in the supervisory and un(b)locked state
Issue: 30-0
DN987378
183
Error messages
General Error Messages of System
2211
INCORRECT MESSAGE ID
This means an incorrect message ID.
2212
INVALID TS VALUE
This means an invalid TS value.
2213
STANDING WAVE RATIO TOO HIGH AT ANTENNA
The standing wave ratio is too high at the antenna.
2214
TX POWER TOO HIGH
Tx power too high
2215
INCORRECT CODING SCHEME WITHOUT
CONFIGURING EDAP POOL AND/OR ENABLING
EGPRS
An Incorrect Coding Scheme was selected without
configuring EDAP pool and/or enabling EGPRS.
2216
CLEARING ALARM FAILED
Clearing alarm failed.
2217
ENERGY EFFICIENT COVERAGE FEATURE IS NOT IN
USE IN BSC
The Energy Efficient Coverage feature is not enabled in
BSC. Either the feature license is not valid, or the feature
status is in disabled state
2218
ENERGY EFFICIENT COVERAGE CAPACITY
EXCEEDED
The license capacity has exceeded for Energy Efficient
Coverage for BCF.
2221
PPP LINKS DOWN
PPP link state is down.
2222
SNMP MESSAGE RETURN UNSUCCESSFUL
SNMP message return is unsuccessful.
2223
SNMP LIB HANDLING FAILED
SNMP lib procedure handling failed.
2224
SNMP RETURNS THE PARAMETER TYPE ERROR
SNMP returns the parameter type error.
2225
SNMP COMMUNICATION IS BUSY
SNMP communication is busy now.
184
DN987378
Issue: 30-0
General Error Messages of System
2226
Error messages
ADDF IS NOT READY
ADDF is not ready.
2227
THE PORT IS NOT SPECIFIC FOR ADDF
The port is not specific for ADDF.
2228
COULD NOT RESOLVE GPB DATA CONTENT
The RNC Element Manager Server Program Block has
failed in resolving the Google Protocol Buffer (GPB) data
content from the header received.
2229
MANDATORY PARAMETER MISSING FROM REQUEST
The RNC Element Manager Server Program Block cannot
proceed with the request due to a missing mandatory
parameter.
2230
UNKNOWN REQUEST TYPE
The RNC Element Manager Server Program Block has
received an unknown request. The type of Google Protocol
Buffer (GPB) message is not recognized.
2231
INVALID M3UA LOAD BALANCER STATE OF UNIT
The M3UA load balancer state of the unit is invalid.
2234
AT LEAST ONE TARGET SPI VALUE MUST BE DEFINED
FOR AN APPLICATION GROUP.
At least one target SPI value must be defined for an
application group.
2236
AT LEAST ONE DSCP VALUE MUST BE DEFINED FOR
AN APPLICATION GROUP.
At least one DSCP Value must be defined for an
Application Group.
2237
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 0.
The Target SPI can have NBR value defined only if NBR in
UL is defined for Initial SPI 0.
2238
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 1.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 1.
2239
Issue: 30-0
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 2.
DN987378
185
Error messages
General Error Messages of System
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 2.
2240
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 3.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 3.
2241
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 4.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 4.
2242
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 5.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 5.
2243
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 6.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 6.
2244
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 7.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 7.
2245
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 8.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 8.
2246
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 9.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 9.
2247
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 10 .
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 10.
2248
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 11.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 11.
186
DN987378
Issue: 30-0
General Error Messages of System
2249
Error messages
TARGET SPI CAN HAVE NBR VALUE DEFINED ONLY IF
NBR IN UPLINK IS DEFINED FOR INITIAL SPI 12.
Target SPI can have an NBR value defined only if the NBR
in the UL is defined for Initial SPI 12.
2250
RNAC-ULMAXBITRATESF128 MUST BE BIGGER THAN
THE RNAC-ULMAXBITRATESF256.
ULmaxBitRateSF128 must be greater than
ULmaxBitRateSF256.
2251
RNAC-ULMAXBITRATESF128 MUST BE SMALLER
THAN RNAC-ULMAXBITRATESF64.
ULmaxBitRateSF128 must be less than
ULmaxBitRateSF64.
2252
WCEL-DBANDHSDPAENABLED CAN BE ENABLED
ONLY WHEN WCEL-DCELLHSDPAENABLED IS
ENABLED.
WCEL-DBandHSDPAEnabled can be enabled only when
WCEL-DCellHSDPAEnabled is enabled.
2253
CAPACITY LIMIT FOR DB DC HSDPA LICENSE
EXCEEDED.
Capacity limit for DB DC HSDPA license exceeded
2255
RNAC-ULMAXBITRATESF32 MUST BE SMALLER THAN
THE RNAC-ULMAXBITRATESF16
RNAC-ULmaxBitRateSF32 must be less than RNACULmaxBitRateSF16.
2259
IP BASED ROUTE ID DOES EXIST, BUT NO
ASSOCIATED IP ADDRESS
The IP-based route ID exists but has no associated IP
address.
2260
HSDPACCENABLEDIUR CAN BE ENABLED IF
HSPAOVERIUR IS ENABLED
The HSDPACCEnabledIur can be enabled if HSPAOverIur
is enabled.
2261
NOT ENOUGH GPB DATA RECEIVED TO PROCESS
REQUEST
The RNC Element Manager Server Program Block is
unable to read enough data from the connected socket
after several retries.
2262
Issue: 30-0
RNAC-ULMAXBITRATESF16 MUST BE SMALLER THAN
THE RNAC-ULMAXBITRATESF8
DN987378
187
Error messages
General Error Messages of System
RNAC-ULmaxBitRateSF16 must be less than RNACULmaxBitRateSF8.
2263
CONFIGURATION OF RNMOBI-PGRNCID IS NOT
ALLOWED IF IT IS OTHER THAN SELF RNCID AND
IUR-NRNCID
Configuration of RNMOBI-PGRNCID is not allowed if it is
other than self RNCID and IUR-NRNCID.
2264
HIGH SPEED RAIL HO CANNOT BE ENABLED
SIMULTANEOUSLY WITH DTM
The Composited Multisite Cell with High Speed Rail
feature cannot be enabled simultaneously with DTM.
2265
HIGH SPEED RAIL HO REQUIRE FIXED PS TERRITORY
SIZE
The Composited Multisite Cell with High Speed Rail
feature requires fixed PS Territory size.
2267
HIGH SPEED RAIL HO CANNOT BE ENABLED
SIMULTANEOUSLY WITH NCCR
The Composited Multisite Cell with High Speed Rail
feature cannot be enabled simultaneously with NCCR.
2268
CAPACITY LIMIT FOR FAST HSPA MOBILITY LICENSE
EXCEEDED.
Capacity limit for Fast HSPA Mobility license exceeded
2276
FREQUENCY BAND NOT PROVIDED
The frequency band for the Precise UL Interference
Measurement is not provided.
2277
TRX SELECTION COULD NOT BE MADE
TRX Selection for Precise UL Interference Measurement
could not be made.
2280
TEST TRX WILL BE RESTARTED
The TRX where Precise UL Interference Measurement will
be restarted
2281
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO RNW OBJECT RESET
The precise UL Interference Measurement is interrupted
due to an object reset.
2282
188
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO RNW OBJECT LOCK
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The precise UL Interference Measurement is interrupted
due to locking of the BCF/BTS/TRX.
2283
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO BLOCKING ALARM IN TEST
TRX
The precise UL Interference Measurement is interrupted
due to a blocking alarm in the test TRX.
2284
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO BSC RESET
The precise UL Interference Measurement is interrupted
due to a BSC reset without a BCF reset.
2285
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO TRX RECOVERY
The precise UL Interference Measurement is interrupted
due to a TRX recovery.
2286
PRECISE UL INTERFERENCE TEST REPORT NOT
RECEIVED FROM BTS
The Precise UL Interference Measurement Test Report
was not received from the BTS.
2288
COUNT OF FREQUENCIES IN THE MEASUREMENT
FREQUENCY LIST EXCEEDED THE MAXIMUM LIMIT
The count of frequencies in the Measurement Frequency
list exceeded the maximum limit.
2289
MEASUREMENT FREQUENCY LIST NOT FOUND
The Measurement Frequency List is not configured.
2292
E-RACH TRX CANNOT BE SELECTED FOR PRECISE
UL INTERFERENCE MEASUREMENT
E-RACH TRX cannot be selected for Precise UL
Interference Measurement.
2294
MEASUREMENT FREQUENCY LIST NOT FOUND IN
RNW DATABASE
The Measurement Frequency List is not found in the RNW
database.
2295
RESPSYNCCOUNTERIP, RESPSYNCTIMERIP,
RESPSYNCTIMERSATIP CANNOT BE MODIFIED IF
RESPSYNCMODENABLEIP IS DISABLE.
RespSyncCounterIP, RespSyncTimerIP, and
RespSyncTimerSatIP cannot be modified if
RespSyncModEnableIP is disabled.
Issue: 30-0
DN987378
189
Error messages
General Error Messages of System
2296
RESPSYNCCOUNTERIP,RESPSYNCTIMERIP,RESPSYN
CTIMERSATIP CANT BE NON DEFAULT IF
RESPSYNCMODENABLEIP DISABLED
RespSyncCounterIP, RespSyncTimerIP, and
RespSyncTimerSatIP cannot be set as non-default value if
RespSyncModEnableIP is disabled.
2297
RF HOP ENABLED BCCH BTS CANNOT HAVE LESS
TRX THAN STANDBY BTS
The BCCH BTS with RF hopping enabled cannot have
less number of TRX than the total number of TRX in the
standby BTS.
2301
RADIO LINK ALREADY EXISTS
Radio link already exists.
2302
RADIO LINK DOES NOT EXIST
Radio link does not exist.
2303
RADIO LINK MODIFICATION IS NOT ALLOWED
Radio link modification is not allowed.
2304
GSM RF CHAINING FEATURE IS NOT IN USE IN BSC
The GSM RF chaining feature is not in use in the BSC.
2305
GSM RF CHAINING CAPACITY EXCEEDED
The GSM RF chaining capacity is exceeded.
2306
GSM RRH LOOP PROTECTION FEATURE IS NOT IN
USE IN BSC
The GSM RRH loop protection feature is not in use in the
BSC.
2307
GSM RRH LOOP PROTECTION CAPACITY EXCEEDED
The GSM RRH loop protection capacity is exceeded.
2310
OPERATOR NOT FOUND IN BSDATA or PCU
The MOCN operator object is not defined in the BSC RNW
database.
2311
OPERATOR EXISTS IN BSDATA
The MOCN operator being created is already present in
the BSC RNW database.
2315
190
OPERATOR POOL ASSOCIATED TO SEGMENT
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Operator pool object is connected to a radio network
segment or cell.
2317
WEIGHT FACTORS SUM NOT 100
The sum of weight factors of operators is not 100.
2318
SPC COUNT EXCEEDS
More than 16 SPCs cannot be configured together for all
operators.
2322
SPC OF OTHER OPERATOR
The SPC is already mapped to another operator ID.
2324
EXISTING NSEI NOT MAPPED
The existing NSEIs are not mapped to operators.
2326
SPC MAPPED TO OPERATOR
New SPC has an existing mapping to an operator object.
2328
INVALID OPERATOR POOL
This means an invalid operator pool object in the PCU.
2332
INVALID OPERATOR
This means an invalid operator object in the PCU.
2333
SHARPER FEATURE IS NOT IN USE IN BSC
Sharper feature is not in use in the BSC.
2334
SHARPER CAPACITY LICENSE EXCEEDED
Sharper capacity license exceeded
2335
NSEI OPERATOR MISMATCH FOUND
The NSEI operator is not active in the segment.
2338
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO SYSTEM RESTART
The precise UL Interference Measurement is interrupted
due to a system restart.
2341
EXTERNAL 1PPS+TOD SYNC FEATURE IS NOT IN USE
IN BSC
The RG301965 GPS 1PPS+ToD Feature is not in use in
the BSC, or the RG301833 Ext1PPS+TOD Sync Support
is not in use in the BSC. When the feature is activated into
Issue: 30-0
DN987378
191
Error messages
General Error Messages of System
use for the BCF, the license of the feature must be
installed to the BSC and the license state must be in ON
state.
2342
EXTERNAL 1PPS+TOD SYNC LICENSE CAPACITY
EXCEEDED
The RG301965 GPS 1PPS+ToD Feature license capacity
is exceeded, or the RG301833 Ext1PPS+TOD Sync
Supportfeaturelicense capacity is exceeded.
2343
IPBRID WITH NO VALID ASSOC IP
The IP-based route ID exists but has no valid associated
IP address.
2344
CODE USED TO INDICATE THE ERROR SCENARIO OF
CPU LOAD MEASUREMENT FAILURE
Code used to indicate the error scenario of CPU load
measurement failure
2345
CODE USED TO INDICATE USER PLANE CPU LOAD
MEASUREMENT SUCCESS
Code used to indicate the user plane CPU load
measurement success
2346
CODE USED TO INDICATE SUCCESSFUL UP CORE
INITIALIZATION
Code used to indicate the successful up core initialization
2347
CODE USED TO INDICATE FLEXIPLATFORM FAILURE
OF UP CORE INITIALIZATION
Code used to indicate the FlexiPlatform failure of up core
initialization
2348
UP MIDDLEWARE FAILED DURING CORE
INITIALIZATION
UP middleware failed during the core initialization.
2349
CP CORE REMOVAL FAILURE IN FLEXIPLATFORM
DURING CP TO UP CORE MOVEMENT
CP core removal failure in flexiplatform during CP to UP
core movement
2350
UP ADDITION FAILURE IN FLEXIPLATFORM DURING
THE CP TO UP CORE MOVEMENT
UP addition failure in flexiplatform during the CP to UP
core movement
192
DN987378
Issue: 30-0
General Error Messages of System
2351
Error messages
UMW FAILED TO RESPOND FOR THE UP ADDITION
DURING THE CP TO UP CORE MOVEMENT
UMW failed to respond for the UP addition during the CP
to UP core movement.
2352
UMW FAILED TO RESPOND IN TIME DURING THE CP
TO UP CORE MOVEMENT
UMW failed to respond in time during the CP to UP core
movement.
2353
CP TO UP CORE MOVEMENT SUCCESS CASE
CP to UP core movement success case
2354
CODE REPORTED FOR INVALID CORE MOVEMENT
REQUEST. CP RUNNING CORES ALREADY IN
MINIMUM SET
Code reported for the invalid core movement request. The
CP running cores already in minimum set.
2355
UP CORE REMOVAL FAILED IN FLEXIPLATFORM
DURING THE UP TO CP CORE MOVEMENT
UP core removal failed in flexiplatform during the UP to CP
core movement.
2356
CP CORE ADDITION FAILED IN FLEXIPLATFORM
DURING THE UP TO CP CORE MOVEMENT
CP core addition failed in flexiplatform during the UP to CP
core movement.
2357
UMW RESPONDS WITH THIS EC FOR THE FAILURE
OF UP CORE REMOVAL DURING UP TO CP CORE
MOVEMENT
UMW responds with this EC for the failure of UP core
removal during the UP to CP core movement.
2358
IUO SHAREDPLMN COULD NOT BE MODIFIED IF
WCEL IS ASSOCIATED WITH IT.
The IUO sharedplmn could not be modified if the WCEL is
associated with it.
2359
CODE USED WHEN THE UP TO CP CORE MOVEMENT
IS SUCCESSFUL
Code used when the UP to CP core movement is
successful
2360
Issue: 30-0
CODE REPORTED FOR INVALID CORE MOVEMENT
REQUEST. UP RUNNING CORES ALREADY IN
MINIMUM SET
DN987378
193
Error messages
General Error Messages of System
Code reported for the invalid core movement request. The
UP running cores already in minimum set.
2361
CORE CONFIGURATION INQUIRY SUCCEEDED
Core configuration inquiry succeeded.
2364
MISMATCH IN MNC AND MNCLENGTH VALUES
A mismatch in MNC and MNClength values.
2365
ONE INSTANCE OF THE LIST IS MANDATORY
One instance of the list is mandatory.
2366
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO PLAN ACTIVATION
The precise UL Interference Measurement is interrupted
due to a plan activation.
2367
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO MANUAL TRX POWER DOWN
The precise UL Interference Measurement is interrupted
due to a manual TRX power down.
2368
MIXED OSC EDGE FEATURE IS NOT IN USE IN BSC
The AH and BBFH for mixed OSC EDGE ULTRA/FLEXI
feature is not in use in the BSC.
2369
MIXED OSC EDGE CAPACITY LICENSE EXCEEDED
The AH and BBFH for mixed OSC EDGE ULTRA/FLEXI
feature capacity has exceeded.
2371
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO AUTO CONFIGURATION
RESET
The precise UL interference measurement is interrupted
due to the auto-configuration reset.
2372
IUR-URAID MUST BE UNIQUE WITHIN IUR-URAIIDLIST
IUR-URAId must be unique within IUR-URAIdList.
2374
BUFFER DOES NOT BELONG TO CURRENT HAND
PROCESS
The buffer to be operated does not belong to the current
hand process.
2375
194
RM2PRB HAS RESENT DMX MESSAGE AS NO ACK
MESSAGE TO FIRSTLY SENT MESSAGE WAS
RECEIVED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
RM2PRB has resent DMX message as no ack message to
firstly sent message was received.
2377
WBTS- IUBTRANSPORTSHARING PARAMETER CAN
BE ENABLED ONLY WHEN WBTS - HSUPACCENABLED
IS SET AS DISABLED.
The WBTS- IubTransportSharing parameter can be
enabled only when WBTS-HSUPACCEnabled is set as
Disabled.
2382
RNFC-PTTENABLED CANNOT BE GREATER THAN
TWO IF WCEL-RTWITHHSDPAFMCGIDENTIFIER IS
NOT DEFINED.
RNFC-PttEnabled cannot be greater than two if WCELRTWithHsdpaFmcgIdentifier is not defined.
2385
IUO-SharedAreaPLMNid must be unique with IUO-PLMNid
IUO-SharedAreaPLMNid must be unique with IUO-PLMNid
2388
IBHO AND MOCN NOT ALLOWED IN SAME CELL
The IBHO and MOCN features cannot be enabled together
in the same cell.
2392
BTSREBALANCEENABLED IS NOT ENABLED
BTSRebalanceEnabled feature state is not enabled.
2394
REBALANCING REJECTED AS SRC CSCP NOT IN WOEX
Rebalancing rejected as SRC CSCP not in WO-EX
2395
REBALANCING REJECTED AS NO OVERLOAD CSCP
Rebalancing rejected as no overload CSCP
2396
REBALANCING REJECTED AS NO CANDIDATE FOR
RECEIVING CSCP
Rebalancing rejected as no candidate for receiving CSCP
2400
BTS RESOURCE REBALANCING LICENSE IS NOT ON
BTS resource rebalancing license is not on.
2401
REBALANCING REJECTED AS NO BTS CANDIDATE
Rebalancing rejected as no BTS candidate by MCERM
2405
RNCERM CANT COEXISTS WITH COSITE
RNCERM cannot coexist with co-site.
2406
Issue: 30-0
REBALANCING REJECTED AS COSITE MCRNC
DN987378
195
Error messages
General Error Messages of System
Rebalancing rejected as co-site MCRNC
2409
REBALANCING REJECTED AS NO RESPONSE FROM
RRA IN PRE-PREPARATORY PHASE
Rebalancing rejected as no response from RRA in prepreparatory phase
2410
REBALANCING REJECTED AS NO RESPONSE FROM
RRA IN PREPARATORY PHASE
Rebalancing rejected as no response from RRA in
preparatory phase
2411
REBALANCING REJECTED AS DONATING CSCP NOT
IN W0 STATE
Rebalancing rejected as donating CSCP not in W0 state
2412
REBALANCING REJECTED AS RECEIVING CSCP NOT
IN W0 STATE
Rebalancing rejected as receiving CSCP not in W0 state
2413
REBALANCING REJECTED AS BTS DOES NOT
BELONG TO DONATING CSCP
Rebalancing rejected as the BTS does not belong to the
donating CSCP.
2415
REBALANCING STARTED SUCCESSFULLY
Rebalancing started successfully
2417
NRI LENGTH EXCEEDS RANGE
An operator\'s CS NRI range is violated by the modified CS
NRI LEN value.
2418
MOCN FEATURE IN USE
Modification not allowed when MOCN feature is in use.
2419
RNAC-AUTOACINCRESTHYSRTWP CANNOT BE
HIGHER THAN RNAC-AUTOACRLEVELUPDINT
The RNAC-AutoACIncRestHysRTWP cannot be higher
than RNAC-AutoACRLevelUpdInt.
2421
RNAC-AUTOACINCRESTHYSNRTQ CANNOT BE
HIGHER THAN RNAC-AUTOACRLEVELUPDINT
The RNAC-AutoACIncRestHysNRTQ cannot be higher
than RNAC-AutoACRLevelUpdInt.
2423
196
RNAC-AUTOACINCRESTHYSRTWP CANNOT BE
LOWER THAN RNAC-AUTOACDECRESTHYSRTWP.
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The RNAC-AutoACIncRestHysRTWP cannot be lower
than RNAC-AutoACDecRestHysRTWP.
2424
RNAC-AUTOACINCRESTHYSNRTQ CANNOT BE
LOWER THAN RNAC-AUTOACDECRESTHYSNRTQ
The RNAC-AutoACIncRestHysNRTQ cannot be lower than
RNAC-AutoACDecRestHysNRTQ.
2425
IUCS-NETWORKIND AND IUCS-SIGNPOINTCODE
MUST BE UNIQUE AMONG IUCS OBJECTS
The IUCS-NetworkInd and IUCS-SignPointCode must be
unique among IUCS objects.
2426
IUPS-NETWORKIND AND IUPS-SIGNPOINTCODE
MUST BE UNIQUE AMONG IUPS OBJECTS
The IUPS-NetworkInd and IUPS-SignPointCode must be
unique among the IUPS objects.
2427
IUR-NRNCNETWORKIND AND IURNRNCSIGNPOINTCODE MUST BE UNIQUE AMONG
IUR OBJECTS
The IUR-NRncNetworkInd and IUR-NRncSignPointCode
must be unique among IUR objects.
2428
ERROR SENT TO LRM INDICATING HP NOT POSSIBLE
Error sent to LRM indicating HP not possible
2429
WCEL SABENABLED CANNOT BE DISABLED IF
NUMBER OF SCCPCH IS 3
WCEL SABENABLED cannot be disabled if the number of
SCCPCH is 3.
2430
VALUE OF RNPS-PRIFORHSFACHDTCH SHOULD BE
LESS THAN RNPSPRIFORBACKARP1,PRIFORBACKARP2,PRIFORBACKA
RP3.
The value of RNPS-PRIFORHSFACHDTCH should be
less than RNPS-PriForBackARP1, PriForBackARP2, and
PriForBackARP3.
2431
VALUE OF RNPS-PRIFORHSFACHDTCH SHOULD BE
LESS THAN RNPSPRIFORINTTHP1ARP1,PRIFORINTTHP1ARP2,PRIFORI
NTTHP1ARP3
The value of RNPS-PRIFORHSFACHDTCH should be
less than RNPS-PriForIntTHP1ARP1,
PriForIntTHP1ARP2, and PriForIntTHP1ARP3.
Issue: 30-0
DN987378
197
Error messages
General Error Messages of System
2432
VALUE OF RNPS-PRIFORHSFACHDTCH SHOULD BE
LESS THAN RNPSPRIFORINTTHP2ARP1,PRIFORINTTHP2ARP2,PRIFORI
NTTHP2ARP3
The value of RNPS-PRIFORHSFACHDTCH should be
less than RNPS-PriForIntTHP2ARP1,
PriForIntTHP2ARP2, and PriForIntTHP2ARP3.
2433
VALUE OF RNPS-PRIFORHSFACHDTCH SHOULD BE
LESS THAN RNPSPRIFORINTTHP3ARP1,PRIFORINTTHP3ARP2,PRIFORI
NTTHP3ARP3
The value of RNPS-PRIFORHSFACHDTCH should be
less than RNPS-PriForIntTHP3ARP1,
PriForIntTHP3ARP2, and PriForIntTHP3ARP3.
2436
RE-BALANCE NBAP LINK SWITCH FAILED BUT
ROLLBACK SUCCEEDED
Re-balance NBAP link switch failed, but rollback
succeeded.
2437
RE-BALANCE NBAP LINK SWITCH FAILED AND
ROLLBACK FAILED
Re-balance NBAP link switch failed, and rollback failed.
2438
MOVING DISK LOG INTO DATABASE PROHIBITED
Some program block has prohibited moving disk log into
database files. You can wait until it is allowed to write in
database files again, or you can force a change of status
on disklog with the message change_log_state_s. If you
do not know who prohibited moving and why it is very
dangerous to change the state, do not make the state
change since the moving can be prohibited because of
such an operation during which it is absolutely forbidden to
move disklog, e.g. dumping of database.
2439
RE-BALANCE NBAP LINK SWITCH(REMOVE/CREATE)
FAILED DUE TO S-CSCP/T-CSCP RESTART/FAULTY
SWO
Re-balance NBAP link switch(remove/create) failed due to
S-CSCP/T-CSCP restart/faulty SWO.
2440
RE-BALANCE NBAP LINK SWITCH FAILED DUE TO
QNIUB RESTART/FAULTY SWO
Re-balance NBAP link switch failed due to QNIUB
restart/faulty SWO.
198
DN987378
Issue: 30-0
General Error Messages of System
2441
Error messages
RE-BALANCE NBAP LINK SWITCH FAILED DUE TO
SOME SCTP SOCKETS NOT FOUND ACCORDING TO
INFO FROM VEXILI
Re-balance NBAP link switch failed due to some SCTP
sockets not found according to the group ID and ports info
from VEXILI.
2442
RE-BALANCE NBAP LINK SWITCH FAILED AS PORTS
INFO FROM VEXILI IS NOT SAME WITH PORTS INFO
IN NBMPRO
Re-balance NBAP link switch failed as ports info from
VEXILI is not same with ports info in NBMPRO.
2443
RE-BALANCE NBAP LINK SWITCH(CREATE) FAILED
DUE TO SOME NBAP LINK IS ON CSCP OTHER THAN
T-CSCP
Re-balance NBAP link switch(create) failed due to some
NBAP link is on CSCP other than T-CSCP.
2444
RE-BALANCE NBAP LINK SWITCH FAILED AS SCTP
SOCKETS ARE NOT READY FOR SENDING NBAP
MESSAGES
Re-balance NBAP link switch failed as SCTP sockets are
not ready for sending NBAP messages.
2445
PRIORITY OF SIB18 MUST NOT BE HIGHER THAN
PRIORITY OF SIB11.
The priority of SIB18 must not be higher than the priority of
SIB11.
2446
IF FLEX IU OFF, CANNOT CREATE MORE THAN 1 IUCS
INSTANCE WITH THE SAME IUOID
If Flex IU OFF cannot create more than 1 IUCS instance
with the same IUOId.
2447
IF FLEX IU OFF, CANNOT CREATE MORE THAN 1 IUPS
INSTANCE WITH THE SAME IUOID
If Flex IU OFF cannot create more than 1 IUPS instance
with the same IUOId.
2448
NO PAIRED CS CN CAN BE FOUND FOR THE PS CN
There is no paired CS CN that can be found for the PS
CN.
2450
SHAREDAREAPLMNID MUST BE UNIQUE FOR EVERY
IUO OBJECT
The SharedAreaPLMNid must be unique for every IUO
object.
Issue: 30-0
DN987378
199
Error messages
General Error Messages of System
2451
IUO-PLMNID AND SHAREDAREAPLMNID MUST NOT
BE SAME
The IUO-plmnid and SharedAreaPLMNid must not be
same.
2453
IUO OBJECT CANNOT BE DELETED IF ITS IUOID IS
USED BY IUCS OR IUPS INSTANCE
The IUO Object cannot be deleted if its IUOid is used by
an IUCS or IUPS instance.
2454
IUO CANNOT BE DELETED IF MAPPED TO CBCI
The IUO cannot be deleted if it is mapped to CBCI.
2456
WCEL CANNOT BE MODIFIED AS MOCN CELL IF IT IS
NOT ASSOCIATED TO IUO-PLMNID(PRIMARY PLMN)
WCEL cannot be modified as an MOCN cell if it is not
associated with IUO-PLMNId (primary PLMN).
2457
DURING SAB CONFIGURATION IN WCEL, THERE
MUST BE A CBCI MAPPED TO IUO
During SAB configuration in WCEL, there must be a CBCI
mapped to IUO.
2459
IUCS ,IUPS COULD NOT BE DELETED IF IT IS MAPPED
TO WCEL
The IUCS and IUPS could not be deleted if it is mapped to
a WCEL.
2460
WCEL SETUP FAILED AS CORRESPONDING
IUPS,IUCS OBJECT NOT FOUND
WCEL setup failed as the corresponding IUPS and IUCS
object is not found
2465
SECONDARY PLMN EXCEEDS
For a given operator, the number of secondary PLMN IDs
have exceeded.
2468
DUPLICATE OPERATOR PARAMETER
Duplicate operator parameter in the configuration.
2469
LOAD BALANCING TYPE NOT SUPPORTED
The load balancing type is not supported with MOCN.
2470
RE-BALANCING REJECTED FOR BTS DUE TO
ONGOING LCS EMERGENCY
Re-balancing rejected for BTS due to ongoing LCS
emergency.
200
DN987378
Issue: 30-0
General Error Messages of System
2471
Error messages
SEGMENT - ADJACENT SEGMENT POOL ID
MISMATCH
Operator pool IDs are different for the segment and its
adjacent segment, when one of the segments supports
packet data services.
2472
MORE THAN 1 IUO COULD NOT BE CREATED IF RAN
SHARING AND ICR ARE DISABLED
More than 1 IUO could not be created if RAN sharing and
ICR are disabled.
2473
MOCN CONFIGURATION DELIVERY FAILED
The MOCN Configuration delivery to PCU has failed. The
possible recovery action is a PCU cold restart.
2475
IN SEAMLESS SW UPGRADE, CODE IS RETURNED IF
MFSPRB CANNOT FIND VERSION CONVERSION
LIBRARY FOR A SPECIFIC FILE
In seamless software upgrade, the error code is returned if
MFSPRB cannot find the version conversion library for a
specific file.
2476
IN SEAMLESS SW UPGRADE, CODE IS RETURNED IF
MFSPRB CANNOT FIND THE VERSION CONVERSION
ROUTINE IN A LIBRARY
In seamless software upgrade, the error code is returned if
MFSPRB cannot find the version conversion routine in a
version conversion library.
2477
NO PAIRED PS CN CAN BE FOUND FOR THE CS CN
No paired PS CN can be found for the CS CN.
2478
RNCERM RECVCSCPLOADTHR CANNOT BE GREATER
THAN RNCERM DONATECSCPLOADTHRHI.
Rncerm RecvCscpLoadThr cannot be greater than
Rncerm DonateCscpLoadThrHi.
2479
GIVEN BUFFER NOT BIG ENOUGH FOR CONVERSION
RESULT
The given buffer is not big enough for the conversion
result.
2480
IP SUPERVISION FAILURE DETECTED BY L2L2
MANAGER IN CO-SITING
IP supervision failure detected by L2L2 manager in cositing.
Issue: 30-0
DN987378
201
Error messages
General Error Messages of System
2482
SAB ENABLED SCCPCH COUNT IS LESS THAN 2 OR
COUNT IS 2 AND NUMBER OF CTCH LESS THAN 11
SABEnabled can be enabled if either NbrOfSCCPCHs
equals to 2 and NforCTCH is greater than 10 or
NbrOfSCCPCHs is 3.
2484
IUO-PLMNID CANNOT BE MODIFIED AS IUO IS
MAPPED TO IUPS OR IUCS.
The IUO-PLMNid cannot be modified as the IUO is
mapped to IUPS or IUCS.
2485
IUO-PLMNID CANNOT BE MODIFIED AS IUO IS
MAPPED TO CBCI.
The IUO-PLMNid cannot be modified as the IUO is
mapped to CBCI.
2486
SPC NOT MAPPED
The SPC has no operator mapping.
2487
RNFC-MOCNENABLED CANNOT BE DISABLED IF
MOCN WCEL EXISTS.
RNFC-MOCNEnabled cannot be disabled if MOCN WCEL
exists.
2488
ALL NON BCCH TRXS MUST BE DFCA TRXS IN BTS
THAT HAS DFCA MA LIST FOR PS OR CSPS USAGE
If the DFCA mode of the BTS is DFCA Hopping, and if
DFCA MA list usage is either PS usage or both CS and PS
usage, then all unlocked non-BCCH TRXs of the BTS must
be DFCA TRXs.
2491
IUO-CSCNDRXLENGTH MUST HAVE SAME VALUE
AMONG ALL IUO BY USING RNW PLAN IF RNFCMOCNENABLED IS ENABLED.
The IUO-CSCNDRXLength must have same value among
all IUO by using RNW Plan if RNFC-MOCNEnabled is
enabled.
2492
IUO-PSCNDRXLENGTH MUST HAVE SAME VALUE
AMONG ALL IUO BY USING RNW PLAN IF RNFCMOCNENABLED IS ENABLED.
The IUO-PSCNDRXLength must have the same value
among all IUO by using the RNW Plan if RNFCMOCNEnabled is enabled.
2493
202
IUO-CS_T3212 MUST HAVE SAME VALUE AMONG ALL
IUO BY USING RNW PLAN IF RNFC-MOCNENABLED IS
ENABLED.
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The IUO-CS_T3212 must have the same value among all
IUO by using RNW Plan if RNFC-MOCNEnabled is
enabled.
2494
IUO-PS_NMO MUST HAVE SAME VALUE AMONG ALL
IUO BY USING RNW PLAN IF RNFC-MOCNENABLED IS
ENABLED
The IUO-PS_NMO must have the same value among all
IUO by using the RNW Plan if RNFC-MOCNEnabled is
enabled.
2495
UMW TIMESOUT FOR THE UP TO CP CORE
MOVEMENT REQUEST
UMW failed to respond in time during the UP to CP core
movement.
2497
SIB DATA ENCODING FAILED
SIB data encoding failed
2498
INVALID SIB DATA IN DATABASE
There is an invalid SIB data in the database.
2499
SIB DATA EXCEEDS THE MAXIMUM SIZE
SIB data exceeds the maximum size.
2500
SIB DATA BELOW THE MINIMUM SIZE
SIB data is below the minimum size.
2501
SIB DATA ENCODING FAILURE
SIB data encoding failure
2502
SDR repository is reserved.
SDR repository is reserved.
2503
WCEL-PTXPRIMARYCPICH CANNOT BE DIFFERENT IN
WCELS HAVING SAME SECTOR ID.
WCEL-PtxPrimaryCPICH cannot be different in WCELs
having the same sector ID.
2508
Error code sent to RMD when P-Ctrl timeout for the
acknowledgement from the application (L2).
2509
PRECISE UL INTERFERENCE MEASUREMENT IS
INTERRUPTED DUE TO INTELLIGENT SHUT DOWN
The precise UL Interference Measurement is interrupted
due to an intelligent shut down.
Issue: 30-0
DN987378
203
Error messages
General Error Messages of System
2510
WCEL CANNOT BE CREATED WITH IUOSHAREDAREAPLMNID IF IMSI BASED HO
OPTIONALITY IS OFF.
WCEL cannot be created with IUO- SharedAreaPLMNid if
the IMSI-based HO option is off.
2511
TOP PHASE SYNC FEATURE IS NOT IN USE IN BSC
ToP Phase Synchronisation for DFCA feature is not in use
in the BSC.
2512
TOP PHASE SYNCH REQUIRES PACKET ABIS OVER
ETHERNET AT MASTER
The Top Phase Synchronization for DFCA feature requires
Packet Abis Over Ethernet connection type at
Synchronization Master clock BCF.
2513
INCORRECT TRE ID IN LMU AREA WHEN TOP PHASE
SYNCHRONIZATION IS IN USE
There is an incorrect TREID in LMU Area when Top Phase
Synchronization is in use.
2515
BSS TOP PHASE SYNC TIMING LIMIT VALUE TOO
HIGH FOR DFCA WITH OSC
BSS ToP Phase Sync Timing Limit value too high for
DFCA with OSC
2516
NOT MORE THAN ONE RANDOM HOPPING DFCA MAL
LIST IS ALLOWED FOR A BTS
Only one random hopping DFCA MA list can be attached
to a BTS.
2520
SIB11 DATA ENCODING FAILED
Sib11 data encoding failed
2521
SIB11BIS DATA ENCODING FAILED
Sib11bis data encoding failed
2522
SIB12 DATA ENCODING FAILED
Sib12 data encoding failed
2523
INVALID SIB11 DATA IN DATABASE
There is an invalid SIB11 data in the database.
2524
INVALID SIB11BIS DATA IN DATABASE
There is an invalid SIB11bis data in the database.
2525
204
INVALID SIB12 DATA IN DATABASE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
There is an invalid SIB12 data in the database.
2526
SIB11 DATA EXCEEDS THE MAXIMUM SIZE
Sib11 data exceeds the maximum size.
2527
SIB12 DATA EXCEEDS THE MAXIMUM SIZE
Sib12 data exceeds the maximum size.
2528
SIB11 DATA BELOW THE MINIMUM SIZE
Sib11 data is below the minimum size.
2529
SIB11BIS DATA BELOW THE MINIMUM SIZE
Sib11bis data is below the minimum size.
2530
SIB12 DATA BELOW THE MINIMUM SIZE
Sib12 data is below the minimum size.
2531
SIB11BIS DATA EXCEEDS THE MAXIMUM SIZE
Sib11bis data exceeds the maximum size.
2533
2-STEP QUALITY COMPENSATION THRESHOLD
LOWER THAN 1-STEP QUALITY COMPENSATION
THRESHOLD
Step 2 quality compensation threshold for OSC
multiplexing is lower than Step 1 quality compensation
threshold.
2536
AN ACCOUNT IS ALREADY ATTACHED
Another MML account is already attached to an event
triggered symptom data collection feature.
2539
AN ACTIVE PROFILE EXIST
A profile is already active.
2540
NO ACTIVE PROFILE EXISTS
No active profile exists.
2543
XML VALIDATION ERROR
XML validation error
2544
CPU LOAD ABOVE LIMT
The CPU load in the unit is above the allowable limit for
event-triggered symptom data collection.
2548
MEMORY DUMP GUARD TIMER EXPIRED
The PCU2 memory dump guard timer has expired.
Issue: 30-0
DN987378
205
Error messages
General Error Messages of System
2549
RECOVERY ACTIONS STOPPED MEMORY DUMP
Because of some recovery actions, PCU2 memory dump
collection is stopped.
2551
MAX REGISTRATIONS FOR ALARM EXCEEDED
The number of processes trying to register for the alarm
exceeds limit.
2552
RELAY MSS WAS NOT FOUND IN GRR DATABASE
Relay MSS is not found in the GRR database.
2553
RELAY MSS IS NOT IN LIST IN THE GCR RECORD
Relay MSS is not found in the list of GCR record in the
GRR database.
2554
UPPER LIMIT OF DISPATCHER, VOICE RECORDER
AND RELAY MSS IS EXCEEDED
The upper limit of the dispatcher, voice recorder, and relay
MSS is exceeded.
2555
RELAYMSS ALREADY EXISTS IN GRR DATABASE
Relay MSS already exists in the GRR database.
2556
TBU HW CONNECTIONS CONFIGURATION OF WO TBU
AND SP TBU ARE INCONSISTENT
TBU HW connection configurations of WO TBU and SP
TBU are inconsistent. TBUs are 2N redundant units so a
controlled switchover is not allowed when they have
different HW connections configuration.
2559
CHAIN DOES NOT EXIST
The chain does not exist.
2560
FILE CREATION FAILED AFTER 5 RETRIES
The file creation initiated by the PCU is not successful after
5 retry attempts.
2561
WRITE TO FILE FAILED AFTER 5 RETRIES
Write-to-file initiated by PCU is not successful after five
retries/attempts.
2563
DUMP COLLECTION ENDS DUE TO UNKNOWN
FAILURE AT PCU
There is some unknown failure at the PCU that caused
failure in dump collection.
2564
206
TOO MANY CHAINS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The maximum amount of chains has been reached.
2565
RNARDSACGUARDTIME SHOULD BE SMALLER THAN
RNC-RESTRICTIONINTERVAL
The RNARDSACGuardTime should be less than RNCRestrictionInterval.
2566
Some of the child units are in active state.
Some of the child units are in active state.
2568
MSS ADDRESS ALREADY EXISTS IN GRR DATABASE
MSS address already exists in the GRR database.
2570
VLR ID ALREADY EXISTS
The VLR ID that will be added is the same as the one
already existing in the configured file. Input another VLR
ID.
2571
VLR NAME ALREADY EXISTS
The VLR name that will be added is the same as the one
already existing in the configured file. Input another VLR
name.
2573
SCTP ASSOCIATION DOES NOT EXIST
SCTP association does not exist in the VLR.
2575
SOURCE PARAMETER SET DOES NOT EXIST
The source parameter set does not exist.
2579
RESOURCE RESERVATION IS REJECTED BECAUSE
TRANSPORT UNIT IS TOO BUSY.
Resource reservation is rejected because the transport
unit is too busy.
2581
RESOURCE RESERVATION IS REJECTED BECAUSE
CENTRAL RESOURCE MANAGEMENT UNIT IS TOO
BUSY.
Resource reservation is rejected because the central
resource management unit is too busy.
2583
THE RUNNING BUILD IS NOT BU FOR CREATING
BACKUP
The running build is not BU for creating backup build for
PrPRNC.
2584
Issue: 30-0
NO VALID DIRECTORY NAME FOR USE
DN987378
207
Error messages
General Error Messages of System
No valid directory name can be generated for the new
backup build for service.
2585
MISMATCH BETWEEN RECORDED BASE BUILD AND
BASE BUILD GIVEN BY USER
Mismatch between the recorded base build in the
configuration file and the base build given by the user
2586
CREATE BACKUP NOT ALLOWED BEFORE DELETING
EXISTING BACKUP
Creation of backup is not allowed before deleting an
existing backup for the given service.
2587
THE ONGOING TASK STOPPED BY USER
The user stopped the ongoing task.
2588
A TASK IS ALREADY ONGOING
A task is already ongoing.
2589
CONFIG FILE BKBMAFGX.XML DOES NOT EXIST
The config file bkbmafgx.xml does not exist.
2590
CONFIG FILE BKBMAFGX.XML WITH WRONG FORMAT
Config file bkbmafgx.xml with wrong format
2591
FAIL TO READ CONFIG FILE BKBMAFGX.XML
Failure to read the config file bkbmafgx.xml
2592
FAIL TO DELETE DIRECTORY
Failure to delete directory
2593
FAIL TO CHECK THE EXISTENCE OF DIRECTORY
Failure to check the existence of directory
2594
ADDRESS ALREADY ASSIGNED TO THE GIVEN
GROUP CALL REFERENCE
The address is already assigned to the given group call
reference.
2595
ADDRESS WAS NOT FOUND FOR THE GIVEN GROUP
CALL REFERENCE
The address is not found for the given group call
reference.
2596
GROUP NAME WAS NOT FOUND IN GCR DATABASE
The group name is not found in the GCR database.
208
DN987378
Issue: 30-0
General Error Messages of System
2599
Error messages
MC HSDPA LICENSE STATE MUST BE ON FOR CELL
UNLOCK WHEN WCEL-MCELLHSDPAENABLED IS
ENABLED.
The MC HSDPA license state must be ON for cell unlock
when WCEL-MCHSDPAENABLED is enabled.
2600
THE NUMBER OF MC HSDPA ENABLED CELLS MUST
NOT EXCEED THE LICENSE CAPACITY.
The number of MC HSDPA-enabled cells must not exceed
the license capacity.
2604
MAXIMUM NUMBER OF RNCSRV OBJECT EXCEEDED
The maximum number of RNCSRV objects is exceeded.
2605
RNCSRV OBJECT ALREADY CREATED IN BACKUP
PRNC
RNCSRV object already created in backup PRNC.
2606
USER CANNOT CREATE OR MODIFY OR DELETE
RNCSRV OBJECT IN PROTECTED PRNC
User cannot create, modify, or delete RNCSRV object in
protected PRNC.
2607
DATA SYNCH STATUS CANT BE SET AS NOT
APPLICABLE IN BACKUP PRNC
Data synch status cannot be set as not applicable in the
backup PRNC.
2608
BKPRNC OBJECT CREATION OR MODIFICATION OR
DELETION NOT POSSIBLE IN BACKUP PRNC
BKPRNC object creation, modification, or deletion is not
possible in the backup PRNC.
2609
BKPRNC OBJECT IS NOT APPLICABLE FOR COSITE
ENABLED RNC
The BKPRNC object is not applicable for cosite-enabled
RNC.
2610
BKPRNC OBJECT CAN BE CREATED ONLY FOR PURE
IP BASE CONFIGURATION RNC
The BKPRNC object can be created only for pure IP-based
configuration RNC.
2611
Issue: 30-0
BACKUP PRNC IP ADDRESS SHOULD BE UNIQUE
AMONG THE BKPRNC OBJECTS IN PROTECTED
PRNC
DN987378
209
Error messages
General Error Messages of System
Backup PRNC IP address should be unique among the
BKPRNC objects in the protected PRNC.
2612
BKPRNC OBJECT ALREADY CREATED IN PROTECTED
PRNC
The BKPRNC object is already created in the protected
PRNC.
2613
MAXIMUM NUMBER OF BKPRNC OBJECTS ALREADY
CREATED IN PROTECTED PRNC
The maximum number of BKPRNC objects already
created in the protected PRNC
2614
PHYSICAL RNC OBJECT ALREADY CREATED
Physical RNC object is already created.
2615
PHYSICAL RNC OBJECT NOT FOUND
Physical RNC object is not found.
2616
BKPRNC OBJECT NOT FOUND
BKPRNC object is not found.
2617
RNCSRV OBJECT NOT FOUND
RNCSRV object is not found.
2618
COSITE OBJECT CREATION NOT POSSIBLE IF
BKPRNC EXIST IN PRPRNC
Cosite object creation is not possible if the BKPRNC exists
in the protected PRNC.
2619
NO BACKUP BUILD FOR SPECIFIED SERVICE
The backup build does not exist for the specified service.
2621
NOB ACCESS LOWER TRESHOLD IS BIGGER THAN
NOB ACCESS UPPER THRESHOLD
The BTS parameter NOB access lower DL Rx level
threshold is bigger than the BTS parameter NOB access
upper DL Rx level threshold.
2622
NEAREST OFFSET BTS UPLINK POWER TOO LOW
The maximum MS power in the Nearest Offset BTS is less
than the minimum MS power (MS Tx Pwr Max GSM - NOB
UL Power Offset < MS Tx Pwr Min OR MS Tx Pwr Max
GSM1x00 - NOB UL Power Offset < MS Tx Pwr Min).
2623
210
NEAREST OFFSET BTS DOWNLINK POWER TOO LOW
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The maximum transmission power of the Nearest Offset
BTS is less than the minimum transmission power of the
BTS (BS Tx Pwr Max + NOB DL power offset > BS Tx Pwr
Min OR BS TX Pwr Max1x00 + NOB DL power offset > BS
Tx Pwr Min).
2624
MSS ID DOES NOT EXIST
When you inquire, modify, remove, or add the information
of an MSC Server (MSS), the target MSS ID does not
exist.
2627
MSS ID ALREADY EXISTS
When you add a new MSS, the MSS ID already exists.
2628
FIRST MSS MUST BE DEFAULT
When you add the first MSS, its mode must be the default.
2629
IP ALREADY EXISTS
When you add a new IP address or modify an existing IP
address, the IP address already exists.
2630
DEFAULT MSS CAN NOT BE REMOVED
If the MSS mode is the default one, it cannot be removed.
2631
MSS DOES NOT EXIST
When you modify/remove an MSS or add/remove/modify
the MSS IP address, the target MSS does not exist.
2632
LAST DEFAULT MSS CAN NOT BE CHANGED
If there is only one MSS in the default mode, it cannot be
changed to other mode.
2637
NO VALID BACKUP BUILD TO DO SYNCING
OPERATION
There is no valid backup build to do synchronizing
operation.
2643
MAXNUMBEREDCHS MUST BE GREATER THAN
NUMBEREDCHRESERVEDSHOBRANCHADDITIONS IF
IT IS OTHER THAN SPECIAL VALUE.
The MaxNumberEDCHS must be greater than the
NumberEDCHReservedSHOBranchAdditions if it is set to
a value other than the special value.
2646
Issue: 30-0
MC HSDPA IS ENABLED BY THE OPERATOR IN THE
WCEL BUT THE LOCAL CELL AT NODE-B IS NOT MC
HSDPA CAPABLE.
DN987378
211
Error messages
General Error Messages of System
The MC HSDPA is enabled by the operator in the WCEL
but the Local Cell at NODE-B is not MC HSDPA-capable.
2647
BKPRNC COLLECTION FULL
BKPRNC collection is full.
2648
BKPRNC OBJECT ALREADY CREATED
BKPRNC object is already created.
2649
RNCSRVCOLLECTION FULL
RNCSRV collection is full.
2650
RNCSRV OBJECT ALREADY CREATED
RNCSRV object is already created.
2651
ILLEGAL OPERATION FOR PRNC OBJECT IN RNW
PLAN
An XML file processing program block (PABROS, RNC
OMU) has rejected the operation directed to the PRNC
object in the RNW plan.
2652
UNKNOWN PARAMETER FOR RNCSERVICE OBJECT
IN RNW PLAN
An XML file processing program block (PABROS,RNC
OMU) has detected an unknown (or incorrectly placed)
RNCSERVICE object parameter in the RNW plan file.
2654
BKPRNCIP ADDRESS CANNOT BE SET TO VALUE
(0.0.0.0)
The BKPRNCIP address cannot be set to value (0.0.0.0).
2662
NO BASE BUILD
There is no base build.
2663
NO BACKUP BUILD FOR ACTIVATION
No backup build for activation
2665
DEFAULT MSS ALREADY EXISTS
When you try to add a new default MSS, the default MSS
already exists in the MME.
2666
CAN NOT CHANGE THE DEFAULT MSS MODE
When you try to modify the mode of the default MSS, it
cannot be modified.
2667
212
RNC OBJECT CREATION IS NOT POSSIBLE IF THE
PRNCMODE IS SET AS BACKUP
DN987378
Issue: 30-0
General Error Messages of System
Error messages
RNC object creation is not possible if the PRNC mode is
set as backup.
2669
OBJECT WITH DIFFERENT PARAMETERS ALREADY
EXISTS IN DATABASE
The object with different parameters already exists in the
database.
2670
MML COMMAND EXECUTION SUCCEEDS, BUT THERE
IS NO MML OUTPUT DATA
This is the error code for MMLLIB extension for LUA
indicating that there is no MML output data in the internal
buffer.
2671
FAILED TO CALL LUA LIBRARY FUNCTIONS
This is the error code for MMLLIB extension for LUA
indicating that there is a failure in calling the LUA internal
library functions such as string.format.
2672
THE QUESTION NAME FOR MML COMMAND IS TOO
LONG
This is the error code for MMLLIB extension for LUA
indicating that the question name string is longer than
0xFE.
2675
CURSOR EXCEEDS THE START POSITION OF MML
OUTPUT
This is the error code for MMLLIB extension for LUA
indicating that the internal cursor has exceeded the start
position of the file.
2676
CURSOR EXCEEDS THE END POSITION OF MML
OUTPUT
This is the error code for MMLLIB extension for LUA
indicating that the internal cursor has exceeded the end
position of the file.
2677
MML OUTPUT BUFFER DOES NOT EXIST
This is the error code for MMLLIB extension for LUA
indicating that the internal MML output buffer does not
exist.
2679
THERE ALREADY EXISTS A TRACE CONFIGURATION
SET WITH THE GIVEN INDEX
There is an existing trace configuration set with the given
index.
2680
Issue: 30-0
MAXIMUM AMOUNT OF CONF SETS IS ALREADY
REACHED
DN987378
213
Error messages
General Error Messages of System
The maximum amount of conf sets is already reached.
2682
RADIO LINK COUNT MISMATCH
Radio link count does not match with limits or with existing
count.
2683
No free radio links available for allocation
There are no free radio links available for allocation.
2684
DATSYN OBJECT NOT FOUND
DATSYN object is not found.
2685
COCO OBJECT CREATION NOT POSSIBLE IF BKPRNC
OBJECT EXIST IN PROTECTED PRNC
COCO object creation is not possible if the BKPRNC
object exists in the protected PRNC.
2686
DATSYN COLLECTION FULL
DATSYN collection is full.
2687
DATSYN OBJECT ALREADY CREATED
DATSYN object is already created.
2690
RADIO LINK ID OUT OF BOUNDS
Radio link ID is not within legal bounds.
2691
DAEMON FALLBACK COPYING IS ONGOING NOW
Daemon fallback copying is ongoing.
2696
ACTIVE MODE VALUE CANT SET TO ACTIVE OR
LOADED IF ANYOTHER RNCSRV OBJ ACTIVE MODE
IS SET TO ACTIVE OR LOADED
The active mode value cannot be set to active or loaded if
another RNCSRV active mode is set to active or loaded.
2697
IUR IPBASEDROUTEIDIUR CANNOT BE SET TO ZERO
IF THERE EXIST BKPRNC OBJECT IN PRNC
Iur ipbasedrouteidiur cannot be set to zero if there is a
BKPRNC object in the PRNC.
2698
RNCSRV OBJECT
CREATION/MODIFICATION/DELETION NOT POSSIBLE
IF ANY RNCSRV ACTIVITY MODE IS ACTIVE OR
LOADED
RNCSRV object creation, modification, or deletion is not
possible if any RNCSRV object activity mode is active or
loaded.
214
DN987378
Issue: 30-0
General Error Messages of System
2699
Error messages
DATSYN OBJECT MODIFICATION NOT POSSIBLE IF
ANY RNCSRV OBJECT ACTIVITY MODE IS ACTIVE OR
LOADED
Datsyn object modification is not possible if any RNCSRV
object activity mode is active or loaded.
2704
HOPG-ADJGABSPRIOCELLRESELEC AND HOPLADJLABSPRIOCELLRESELEC OF SERVING WCEL
CANNOT BE SAME
HOPG-AdjgAbsPrioCellReselec and HOPLAdjlAbsPrioCellReselec of the serving WCEL cannot be
the same.
2705
HOPI-ADJIABSPRIOCELLRESELEC AND HOPLADJLABSPRIOCELLRESELEC OF SERVING WCEL
CANNOT BE SAME
HOPI-AdjiAbsPrioCellReselec and HOPLAdjlAbsPrioCellReselec of the serving WCEL cannot be
the same.
2706
HOPI-ADJIABSPRIOCELLRESELEC AND HOPGADJGABSPRIOCELLRESELEC OF SERVING WCEL
CANNOT BE SAME
HOPI-AdjiAbsPrioCellReselec and HOPGAdjgAbsPrioCellReselec of the serving WCEL cannot be
the same.
2709
THE BACKUP BUILD WAS CREATED IN SOMAFI BY
OTHER APPLICATION.
Other application created the backup build in SOMAFI
rather than the resilience service.
2710
COMMAND NOT ALLOWED BECAUSE IT IS NOT BASE
BUILD
Command not allowed because it is not a base build.
2711
COMMAND NOT ALLOWED BECAUSE IT IS NOT
BACKUP BUILD
Command is not allowed because it is not a backup build.
2714
RESILIENCY MANAGER IS NOT READY FOR SYSTEM
RESTART
Resiliency Manager is not ready for system restart.
2715
RESILIENCY MANAGER IS NOT READY FOR OMU
SWITCHOVER
Resiliency Manager is not ready for OMU switchover.
Issue: 30-0
DN987378
215
Error messages
General Error Messages of System
2716
sctp configuration should be warned according to
FC394_001180
The configuring SCTP IP and port should be warned
according to FC394_001180.
2718
RNC SYNC ADAPTION FAILED
RNC sync adaptation failed.
2719
RNC SYNC COLLECTION FAILED
RNC synch collection failed.
2720
CURRENT BUILD IS NOT RNC RESILIENCY BUILD
The current build is not an RNC resiliency build.
2721
COLLECTION ON PRIMARY RNC IS ONGOING
Collection on the primary RNC is ongoing.
2722
RESILIENCY MANAGER IS IN WRONG STATE
Resiliency Manager is in the wrong state.
2723
SW download for RF shared Flexi Compact BCF is not
allowed via BSC
Software download for RF shared Flexi Compact BCF is
not allowed via BSC.
2724
ACTIVITY MODE SHOULD NOT BE IN ACTIVE OR
LOADED FOR RNCSRV WHOSE DATA
SYNCHRONIZATION IS REQUESTED
Activity mode should not be active or loaded for RNCSRV
whose data synchronization is requested.
2725
ACTIVITY MODE SHOULD NOT BE IN ACTIVE OR
LOADED FOR ANY RNCSRV WHEN DATA
SYNCHRONIZATION IS REQUESTED
The activity mode should not be in active or loaded mode
for any RNCSRV when data synchronization is requested.
2726
DATA SYNCHRONIZATION FAILED AT BACKUP PRNC
Data synchronization failed at the backup PRNC.
2731
LAYER4 PACKET FILTERING OPERATION IS ONGOING
The LAYER4 packet filtering operation is ongoing.
2738
216
DELETION OF THE LAST NS-VL OF NSE OF THE
MOCN OPERATOR USED BY GPRS-ENABLED BTS IS
NOT POSSIBLE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The deletion of the last NS-VL of the NSE of the MOCN
operator used by a GPRS-ENABLED BTS is not possible.
2739
SW activation for RF shared Flexi Compact BCF is not
allowed via BSC
SW activation for RF shared Flexi Compact BCF is not
allowed via the BSC.
2740
MSS POOL NOT FOUND IN GCR DATABASE
MSS pool is not found in the GCR database.
2741
MSS ALREADY MEMBER OF A POOL IN GCR
DATABASE
MSS is already a member of a pool in the GCR database.
2742
EXECUTION OF UPDATE REQUEST WOULD CAUSE
EXCEEDING OF THE NUMBER OF ALLOWED MSS IN
THE MSS POOL
Execution of update request will cause to exceed the
number of allowable MSSs in the MSS pool.
2743
MSS IS NOT A MEMBER OF THE POOL IN GCR
DATABASE
MSS is not a member of the pool in the GCR database.
2744
ADAPTION IS ONGOING
RAN2512 adaption ongoing error code
2745
CONFIGUATION COMMITTING IS ONGOING
RAN2512 configuration commiting is ongoing ec
2748
COMPRESSION IS ONGOING
RAN 2512 compress is ongoing ec
2749
UP IP COLLECTION IS ONGOING
RAN2512 UP IP collection is ongoing ec
2750
compress abort is ongoing
RAN2512 compress abort is ongoing ec
2751
UP IP COLLECTION ABORT IS ONGOING.
RAN2512 UP IP collection abort ongoing ec
2754
ADAPTING CONFIGURATION ABORT IS IN PROGRESS
Adapting configuration abort process is in progress.
Issue: 30-0
DN987378
217
Error messages
General Error Messages of System
2755
ADAPTING CONFIGURATION IS IN PROGRESS
Adapting configuration is in progress.
2756
NO ONGOING ADAPTING CONFGURATION IS FOUND
Adapting configuration is not in progress.
2757
GIVEN RNC SERVICE ID IS CONFLICTING WITH OWN
RNC SERVICE ID
The given RNC service ID is conflicting with own RNC
service ID.
2758
DATA SYNCHRONIZATION HAS BEEN ABORTED BY
USER
The user has aborted data synchronization.
2759
ALARM CANCEL LIMIT BIGGER THAN RAISE LIMIT
The alarm cancel limit is higher than the raise limit.
2763
No compress is in progress now
No compress in progress.
2764
NO ONGOING DATA SYNCHRONIZATION IS FOUND
No ongoing data synchronization is found.
2765
OTHER MSS ADDRESS OF THE SAME POOL ALREADY
ASSIGNED TO THE GIVEN GROUP CALL REFERENCE
Other MSS address of the same pool is already assigned
to the given group call reference.
2766
MINDSPEED SAR CHIP HARDWARE ERROR
The Mindspeed SAR chip indicates some hardware
problems (PCI bus error, Co-Processor error and so on).
2768
LAST NSE IN MOCN SEGMENT
The last operational NSE of an MOCN segment cannot be
deleted.
2770
BKPRNC OBJECT MODIFICATION OR DELETION NOT
POSSIBLE AS DATA SYNCHRONIZATION IS ONGOING.
BKPRNC object modification or deletion is not possible as
data synchronization is ongoing.
2771
DATA SYNCHRONIZATION IS ONGOING
Data synchronization is ongoing.
2772
218
DATA SYNCHRONIZATION TERMINATION IS ONGOING
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Data synchronization termination is ongoing.
2776
FMCL ALREADY CREATED
The LTE measurement control parameters have already
been created.
2781
BASE STATION CANNOT BE ATTACHED TO LA-CELL
PAIR IN SECONDARY DXT
The base station cannot be attached to an LA-cell pair in
the secondary DXT.
2782
FMCL ID IS ALREADY CREATED.
An LTE Measurement Control (FMCL) object with the given
identity is already created in the radio network database.
2783
FMCL COLLECTION IS FULL.
There is no space for a new LTE Frequency Measurement
Control (FMCL) object in the radio network database.
2784
FMCL IS NOT FOUND.
The LTE Frequency Measurement Control (FMCL) object
cannot be found in the radio network database.
2787
CONFIGURATION DATA OF PRPRNC IS INCOMPATIBLE
WITH BACKUP BUILD VERSION
The configuration data of the PRPRNC is incompatible
with the backup build version.
2788
CAUSE CODE SET AND TYPE MISMATCH
There is a mismatch in the given cause code set name and
type when you modify, restore, or list cause code set.
2789
FEATURE IS DISABLED DEFAULT SET TAKES EFFECT
The feature is disabled when you use the cause code set.
2798
ADJL REFERED BY ADJE- ADJLIDENTIFIER NOT
FOUND.
ADJL referred by ADJE- AdjLIdentifier not found
2799
DELETION OF LAST ADJE UNDER
LTEHANDOVERENABLED ENABLED CELL IS NOT
ALLOWED
Deletion of last ADJE under LTEHandoverEnabledenabled cell is not allowed.
2801
Issue: 30-0
ADJL CANNOT BE DELETED IF IT IS BEING
REFERRED BY ADJE.
DN987378
219
Error messages
General Error Messages of System
ADJL cannot be deleted if ADJE is referring to it.
2803
ADJL-ADJLEARFCN NOT UNIQUE AMONG ADJLS
UNDER A WCEL
The ADJL-EUARFCN value should be unique in ADJL
instances under the same WCEL.
2805
THE SPECIFIED IDENTIFIER OF LTE NEIGHBORING
CELL UNDER WCDMA CELL IS OUT OF RANGE.
The specified identifier of the LTE neighboring cell under
the WCDMA cell is out of range.
2806
THE SPECIFIED LTE NEIGHBOURING CELL UNDER
WCDMA CELL (ADJE) HAS ALREADY BEEN CREATED.
The specified LTE neighboring cell under the WCDMA cell
(adje) has already been created.
2807
THE SPECIFIED LTE NEIGHBOURING CELL UNDER
WCDMA CELL (ADJE) DOES NOT EXIST.
The specified LTE neighboring cell under the WCDMA cell
(adje) does not exist.
2808
BKPRNC OBJECT CREATION MODIFICATION AND
DELETION IS NOT POSSIBLE IF ACTIVITY MODE IS
LOADED
BKPRNC object creation, modification, and deletion are
not possible if activity mode is loaded.
2809
ANTENNA HOPPING EXTENSION FEATURE IS NOT IN
USE IN BSC
The Antenna Hopping Extension feature is not in use in the
BSC; the feature license is not in ON state.
2810
ANTENNA HOPPING EXTENSION FEATURE CAPACITY
IS EXCEEDED
The Antenna Hopping Extension feature capacity is
exceeded.
2811
ADJE NOT FOUND
The LTE neighboring cell under WCDMA cell (ADJE)
object cannot be found in the radio network database.
2812
ADJE ALREADY CREATED UNDER WCEL
An LTE neighboring cell (ADJE) object with the given ID is
already created under the given WCEL ID in the radio
network database.
220
DN987378
Issue: 30-0
General Error Messages of System
2813
Error messages
#E: THE UNIT WHICH IS TO BE REMOVED IS NOT
MARKED FOR GRSD
The unit that is to be removed is not marked for GRSD.
2814
OMS IP ADDRESS SHOULD BE OTHER THAN (0.0.0.0)
FOR OMS SWO REQUEST
The OMS IP address should be other than (0.0.0.0) for
OMS SWO request.
2823
MAXIMUM OF ADJES FOR WCEL
The maximum number of ADJE object relations for the Cell
(WCEL) object is reached.
2824
ADJE COLLECTION FULL
There is no space for an LTE neighboring cell under
WCDMA cell (ADJE) object in the radio network database.
2825
INVALID EREC SECTOR ID
Invalid EREC sector ID
2828
THE LUA EXTENSION INTERFACE HAS NOT BEEN
REGISTERED YET, OR GIVEN EXTENSION INTERFACE
NAME IS WRONG.
This is an error code for Lua common extension interfaces.
It is used when the desired called extension interface is not
registered, or the given extension interface name is wrong.
2829
DATA SYNCHRONIZATION TERMINATION FAILED
Data synchronization termination failed.
2830
DATA SYNCHRONIZATION TERMINATION IS
SUCCESSFULL
Data synchronization termination is successful.
2831
DATA SYNCHRONIZATION TERMINATION FAILED
BECAUSE RESPONSE NOT RECEIVED BY PEER PRNC
Data synchronization termination failed because the peer
PRNC did not receive a response.
2833
DATA SYNCHRONIZATION TERMINATION IS
TRIGGERED WHILE ADAPTATION PHASE IS ONGOING
Data synchronization termination is triggered while
adaptation phase is ongoing.
2837
Issue: 30-0
NUMBER OF LTE NEIGHBOURING CELL UNDER
WCDMA CELL (ADJE) EXCEEDED THE MAXIMUM
LIMIT.
DN987378
221
Error messages
General Error Messages of System
The number of LTE neighboring cell under the WCDMA
cell (adje) exceeded the maximum limit.
2839
Start Value from UE is not received during RLC reestablishment. RLC Reset is triggered to re-sync the same
RLC reset triggered since Start Value is missing.
2840
ADDF IS BUSY
ADDF is busy for configuration.
2846
ALL TRXS UNDER BTS ARE NOT DUAL BEAM TRXS
All TRXs under the BTS are not Dual Beam TRXs.
2852
BPS RECORD ALREADY EXIST
The BPS record to be added already exists.
2853
GIVEN SET ALREADY IN USE
The HSS/PGW parameter override set cannot be deleted
because the given set is in use.
2854
GIVEN SET ALREADY EXISTS
An HSS/PGW parameter override set cannot be added
because the given set already exists.
2855
GIVEN SET DOES NOT EXIST
The HSS/PGW parameter override set cannot be deleted,
modified, and interrogated because the given set does not
exist.
2856
NO BPS EXISTENCE
There is no BPS configured.
2859
UPLINK CLASS RANGE PARAMETERS SHOULD BE IN
ASCENDING ORDER DURING RNC CREATION AND
MODIFICATION
The uplink class range parameters should be in ascending
order during RNC creation and modification.
2860
WRONG FORMAT IN BPS CONFIG FILE
Wrong format in BPS config file
2861
NO ONGOING BPS DELETION TASK IS FOUND
No ongoing BPS DELETION task is found.
2862
222
IMSI based call monitoring not started when a process
family updates the hand monitoring status
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The IMSI-based call monitoring is not started when the
process family tries to update the hand monitoring status
by API update_mon_proc_table.
2867
BKPRNC MODIFICATION/DELETION NOT POSSIBLE IF
THE SERVICE STATUS IS NOT IN IDLE STATE.
BKPRNC modification/deletion is not possible if the service
status is not in idle state.
2868
NO ONGOING BPS FALLBACK COPYING TASK IS
FOUND
No ongoing BPS fallback copying task is found.
2869
REQUESTED RNCSERVICE SERVICE STATUS
SHOULD BE IDLE
The requested RNC service service status should be idle.
2870
SERVICE STATUS SHOULD NOT BE IN ACTIVATING OR
LOADING STATE FOR ANY RNCSRV DURING RNC
RESILIENCY OPERATION
The service status should not be in activating or loading
state for any RNCSRV during RNC resiliency operation.
2871
ERROR RECEIVED FROM RAKTOR DURING RNC
RESILIENCY OPERATION
The error received from raktor during RNC resiliency
operation.
2872
ERROR RECEIVED FROM R0SMAN DURING RNC
RESILIENCY OPERATION
The error received from r0sman during RNC resiliency
operation.
2878
REQUESTED PARAMETER NOT FOUND FROM
JEMMAT CACHE
The requested parameter is not found from the JEMMAT
cache.
2879
JEMMAT CACHE IS FULL
The JEMMAT cache is full.
2880
REQUESTED FEATURE CODE NOT FOUND FROM
JEMMAT CACHE
The requested feature code is not found from the JEMMAT
cache.
2881
Issue: 30-0
JEMMAT CACHE SIZE ERROR
DN987378
223
Error messages
General Error Messages of System
The JEMMAT cache size is not consistent with the
expected data structure size.
2882
RNC CLUSTER OM LINK IS NOT ENABLED BETWEEN
PROTECTED AND BACKUP PRNC.
RNC cluster OM link is not enabled between protected and
backup PRNC.
2884
BACKUP PRNC LICENSE CAPACITY IS NOT
COMPATIBLE WITH PROTECTED PRNC LICENSE
CAPACITY.
The backup PRNC license capacity is not compatible with
the protected PRNC license capacity.
2885
ERROR RECEIVED FROM PEER PROTECTED PRNC.
The error received from peer-protected PRNC.
2886
DURING WCEL MODIFICATION,SECTORID CANNOT BE
MODIFIED IF MCELLHSDPAENABLED PARAMETER IS
ALREADY ENABLED
During WCEL modification, the sector ID cannot be
modified if the MCELLHSDPAENABLED parameter is
already enabled.
2887
AUTOMATIC RECOVERY STARTED IN ALL PCU IN PCU
POOL
The PCU cold restart or PCUM switchover is started in all
PCUs in the PCU pool because of conflict in PCU2 pooling
feature state in the PCUs.
2888
IF IUR- FRLCOVERIURENABLED IS SET TO BE
ENABLED, THEN IUR- HSPAOVERIUR MUST BE
ENABLED.
If IUR-FRLCOverIurEnabled will be enabled, then IURHSPAOverIur must be enabled.
2889
IF IUR- FRLCOVERIURENABLED IS SET TO BE
ENABLED, THEN RNFC- FRLCENABLED MUST BE
ENABLED.
If IUR-FRLCOverIurEnabled will be enabled, then RNFCFRLCEnabled must be enabled.
2890
IUR-DCHSDPAOVERIURENABLED IS SET TO BE
ENABLED, THEN IUR-FRLCOVERIURENABLED MUST
BE ENABLED.
If IUR-DCHSDPAOverIurEnabled will be enabled, then
IUR-FRLCOverIurEnabled must be enabled.
224
DN987378
Issue: 30-0
General Error Messages of System
2891
Error messages
IUR- HSDPA64QAMOVERIURENABLED IS ENABLED
,THEN IUR-FRLCOVERIURENABLED MUST BE
ENABLED.
If IUR- HSDPA64QAMOverIurEnabled is enabled, then the
state of the license HSDPA 64QAM must be on, and IURFRLCOverIurEnabled must be enabled.
2892
IUR-FRLCENABLED CANNOT BE DISABLED IF RNFCFLEXIBLERLCOVERIUR IS ENABLED.
The IUR-FRLCEnabled cannot be disabled if RNFCFlexibleRLCOverIur is enabled.
2893
TD+FD LTE FEATURE IS NOT IN USE IN BSC
This denotes that the TD and FD LTE features are not
enabled in the BSC. Either the feature license is not valid,
or the feature status is in disabled state.
2894
RRILIB CACHE IS FULL
This denotes that the RRILIB cache for RRI data is full.
2895
REQUESTED RRI ELEMENT NOT FOUND FROM RRILIB
DATA CACHE
This denotes that the requested RRI element was not
found in RRILIB data cache.
2896
GET RNCSRV BUILD DIRECTORY FAILED
Get RNCSRV build directory failed.
2897
READ/WRITE RNC CONFIGURATION FILE FAILED
Read/write protect/backup RNC build configuration file
failed
2898
DATABASE CONSISTENCY CHECK INTERRUPTED BY
RNW MANAGER PROGRAM BLOCK
This denotes that the database consistency check was
interrupted by RNW manager program block.
2899
IP MAPPING EXCEEDED CAPACITY
This denotes that the IP mapping records exceeded the
capacity.
2900
NE CANNOT PERFORM ABORT OPERATION AS ONE
ABORT IS ALREADY ONGOING
The NE cannot perform abort operation as an abort is
already ongoing.
Issue: 30-0
DN987378
225
Error messages
General Error Messages of System
2901
NE CANNOT PERFORM ABORT OPERATION AS NO
OPERATION IS ONGOING FOR REQUESTED TASKID
The NE cannot perform abort operation as no operation is
ongoing for the requested task ID.
2902
RNC SERVICE OPERATION FAILED AT PLATFORM
BECAUSE OF MESSAGE TIME OUT.
This denotes that the RNC service operation failed at the
platform because of message timeout.
2903
DATA SYNCHRONIZATION FAILED AT O&M IN
PRPRNC.
This denotes that the data synchronization failed at O&M
in PRPRNC.
2904
DATA SYNCHRONIZATION FAILED AT PLATFORM IN
PRPRNC.
This denotes that data synchronization failed at the
platform in PRPRNC.
2905
RNC SERVICE OPERATION FAILED AT PLATFORM.
This denotes that the RNC service operation failed at the
platform.
2906
RNCSRV OPERATION FAILED AT OM BECAUSE OF
MESSAGE TIME OUT.
This denotes that RNCSRV creation operation failed at OM
because of message timeout.
2907
RNFC-INBEARERAPPPRIOENABLED CANNOT BE
ENABLED WITH CURRENT RNHSPAIBAODSCPHIGHPRIOQPART(1/2) PARAMETER VALUES
When the in-bearer application optimization feature is
enabled, at least one but not all DSCP codes must be
defined with the RNHSPA-IBAODSCPHighPrioQPart1 and
RNHSPA-IBAODSCPHighPrioQPart2 parameters.
2908
AUTO CONFIGURATION IS STARTING
This denotes that auto configuration is starting.
2909
3GPP CONFIGURATION IS ONGOING
The 3GPP configuration is ongoing.
2910
TESTING IP CONNECTIVITY IS ONGOING
This denotes that the testing IP connectivity is ongoing.
226
DN987378
Issue: 30-0
General Error Messages of System
2911
Error messages
DATA SYNC TERMINATION SUCCEEDED AT
REQUESTED PRNC BUT FAILED IN PEER PRNC
Data sync termination succeeded at the requested PRNC
but failed in peer PRNC.
2912
this error code will be used in userplane monitoring agents
DPXTOR,MPXTOR,CMA and DMA
This denotes that an invalid interface type was received in
mon_upcmd from Emil in user plane monitoring agents
DPXTOR, MPXTOR, CMA, and DMA. Expected is
ext_tool_c (value = 1).
2913
Invalid Agent Type received in mon_upcmd from Emil in
userplane monitoring agents.
Invalid Agent Type is received in mon_upcmd from Emil in
user plane monitoring agents.
2914
Invalid Length received in mon_upcmd from Emil in
userplane monitoring agents.
Invalid length is received in mon_upcmd from Emil in user
plane monitoring agents.
2915
Invalid -p option value received in mon_upcmd from Emil
in userplane monitoring agents. Valid range 0-1
This denotes that an invalid -p option value was received
in mon_upcmd from Emil in user plane monitoring agents.
The valid range is 0-1.
2916
Invalid -f option value received in mon_upcmd from Emil in
userplane monitoring agents. Valid range 1-2048
This denotes that an invalid -f option value was received in
mon_upcmd from Emil in user plane monitoring agents.
The valid range is 1-2048.
2917
Invalid message id count received in mon_upcmd from
Emil in up monitoring agents. Valid range -m1-m16.
This denotes that an invalid message ID count was
received in mon_upcmd from Emil in UP monitoring
agents. The valid range is -m1-m16.
2918
Invalid message value received in mon_upcmd from Emil
in up monitoring agents. Valid range 0-0xFFFF
This denotes that an invalid message value was received
in mon_upcmd from Emil in UP monitoring agents. The
valid range is 0-0xFFFF.
2919
Issue: 30-0
Invalid command id count received in mon_upcmd from
Emil in up monitoring agents. Valid range -k1 to -k10.
DN987378
227
Error messages
General Error Messages of System
This denotes that an invalid command ID count was
received in mon_upcmd from Emil in UP monitoring
agents. The valid range is -k1 to -k10.
2920
Invalid command value in mon_upcmd from Emil in up
monitoring agents . Refer Userplane monitoring guide.
This denotes an invalid command value in mon_upcmd
from Emil in UP monitoring agents. Refer to the user plane
monitoring guide.
2921
Invalid -t value received in mon_upcmd from Emil in
userplane monitoring agents. Valid range 0x00xFFFFFFFF
This denotes that an invalid -t value was received in
mon_upcmd from Emil in user plane monitoring agents.
The valid range is 0x0-0xFFFFFFFF.
2922
Invalid -t option without -b option in mon_upcmd from Emil
in userplane monitoring agents.
This denotes an invalid -t option without the -b option in
mon_upcmd from Emil in user plane monitoring agents.
2923
Invalid -s value received in mon_upcmd from Emil in
userplane monitoring agents. Valid range 20-2000
This denotes that an invalid -s value was received in
mon_upcmd from Emil in user plane monitoring agents.
The valid range is 20-2000.
2924
Invalid -b value. Refer Userplane monitoring guide
Invalid -b value, refer to the user plane monitoring guide
2925
Invalid -w value received in mon_upcmd from Emil in up
monitoring agents. Valid range 1-250
This denotes that an invalid -w value was received in
mon_upcmd from Emil in UP monitoring agents. The valid
range is 1-250.
2926
Invalid -c value received in mon_upcmd from Emil in
userplane monitoring agents. Valid range 0-999
This denotes that an invalid -c value was received in
mon_upcmd from Emil in user plane monitoring agents.
The valid range is 0-999.
2927
Wrong command format or invalid option received in
mon_upcmd from Emil in userplane monitoring agents
A wrong command format or an invalid option was
received in mon_upcmd from Emil in user plane monitoring
agents.
228
DN987378
Issue: 30-0
General Error Messages of System
2928
Error messages
Component ID is mandatory when process name is given
for up monitoring agents in emil.
The Component ID is mandatory when process name is
given for UP monitoring agents in Emil.
2929
Unknown Process name or process ID is given in emil for
up monitoring agents.
This denotes that an unknown process name or process ID
is given in Emil for UP monitoring agents.
2930
Invalid component_id value in up monitoring agent from
emil.Valid range 0x0-0xFFFF
This means that there is an invalid component_id value in
the UP monitoring agent from Emil. The valid range is 0x00xFFFF.
2931
either K or M is mandatory in up monitoring agent
command from emil. -k(1-10) or -m(1-16)
Either K or M is mandatory in the UP monitoring agent
command from Emil. -k(1-10) or -m(1-16)
2932
Mon Session started without Mon command in up
monitoring agent from GIVAXI
This denotes that the Mon session has started without the
Mon command in the UP monitoring agent from GIVAXI.
2933
monitoring can not be started as up monitoring agent load
cutter is active now.
This means that the monitoring cannot be started as the
UP monitoring agent load cutter is now active.
2934
TRIAL CONFIGURATION IS NOT ALLOWED IN BKPRNC
Trial configuration is not allowed in bkPRNC.
2935
PACKET ABIS SYNC. TOP IEEE1588V2 IS NOT IN USE
IN BSC
Packet Abis sync ToP IEEE1588v2 feature license is not
enabled in the BSC.
2936
TOO FEW ITEMS IN OBJECT LIST PARAMETER.
The RNW plan list parameter contains too many items.
2937
INCONSISTENCY FOUND FOR RNCSRV OBJECT.
An inconsistency found for the RNCSRV object, RNCSRV
object created in platform but the same is not created in
RNWDB
Issue: 30-0
DN987378
229
Error messages
General Error Messages of System
2938
RNFC-AutoACResBTSEnabled CAN ONLY BE ENABLED
IF RNFC-BTSLoadIndSel IS (PRIVATE CAUSE CODE IS
USED)
RNFC-AutoACResBTSEnabled can only be enabled if
RNFC-BTSLoadIndSel is (PRIVATE CAUSE CODE IS
USED)
2939
RNFC-SUBSCRIBERTRACE IS DISABLED
This denotes that RNFC-SUBSCRIBERTRACE is
disabled.
2940
NOKIA NODEB BTS CONFIGURATION IS NOT
SUPPORTED
The Nokia NodeB BTS configuration is not supported.
2941
UNKNOWN PARAMETER FOR ADJE IN RNW PLAN
An XML file processing program block (PABROS, RNC
OMU) has detected an unknown (or incorrectly placed)
ADJE object parameter in the RNW plan file.
2942
This denotes that an error was sent to LRM indicating a
hot plug is in progress.
2943
RFU control command is received at userplane, before the
RLC channel has been configured.
The RFU control command is received at userplane,
before the RLC channel has been configured.
2944
RNC is not receiving UL SYNC frames on CCH TrCh from
the BTS. This is most likely a CCH transport problem.
CCH setup has failed because the RNC has sent DL
SYNC frame on CCH TrCh, but the BTS does not respond
by UL SYNC frame. This is most likely a CCH transport
problem.
2945
RECEIVED DUPLICATE SERVICE ID
This denotes that RMDPRB has detected the service ID as
duplicate.
2946
UP CHANNEL RESOURCES FULL
This denotes that no more channel can be added to the
UP application for the service requested.
2947
RMDPRB NO MORE INSTANCES LEFT
This denotes that no more instance can be allocated in
RMDPRB.
2948
230
RMDPRB HAND CREATION FAILED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
This denotes that the hand creation failed in RMDPRB.
2949
DESTINATION SERVICE ID NOT FOUND IN RMDPRB
This denotes that the destination service ID is not found in
RMDPRB.
2950
NO MORE UP CONNECTIONS LEFT
This denotes that no free UP connections are available.
2951
RMDPRB NO MORE CHANNELS LEFT FOR SERVER
TYPE SERVICE (HS_CELL)
This denotes that no more channels can be added based
on hs_bind_id (only for HS CELL server).
2952
PCOM CONNECTION OPEN TIMED OUT
The RMDPRB has timed out to open a connection with
PCOM.
2953
UP CHANNEL ADDITION TIMED OUT
The RMDPRB has timed out to add a channel in the UP
application.
2954
UP BRANCH MODIFICATION FAILED
The RMDPRB has timed out to modify a branch.
2955
PCOM REPORTED ERROR FOR CONNECTION OPEN
The RMDPRB received a negative acknowledgement for a
connection open from PCOM.
2956
UP REPORTED ERROR FOR CHANNEL ADDITION
The RMDPRB received a negative acknowledgement
while adding a channel from the UP application.
2957
UP REPORTED ERROR FOR BRANCH MODIFICATION
The RMDPRB received a negative acknowledgement
while modifying a branch from the UP application.
2958
UP REPORTED ERROR FOR CHANNEL RELEASE
The RMDPRB received a negative acknowledgement
while releasing a channel from the UP application.
2959
PCOM REPORTED ERROR FOR CONNECTION CLOSE
The RMDPRB received a negative acknowledgement
while closing a connection from PCOM.
2960
Issue: 30-0
RMDPRB RECEIVED UNKNOWN BRANCH TYPE
DN987378
231
Error messages
General Error Messages of System
The RMD has received an invalid branch type.
2961
RMDPRB RECEIVED UNKNOWN CONNECTION ID
The RMD received an unknown connection ID.
2962
UP CHANNEL RELEASE TIMED OUT
The RMDPRB has timed out to release a channel in the
UP application.
2963
PCOM CLOSE CONNECTION TIMED OUT
The RMDPRB has timed out to close a connection with
PCOM.
2964
RMDPRB RECEIVED UNKNOWN SERVICE ID
The RMDPRB has no instance for the service ID provided.
2965
P_CTRL BRANCH MODIFICATION TIMED OUT
The RMDPRB received a P_CTRL timeout while modifying
a branch in the UP application.
2966
PCOM REPORTED ERROR FOR IMMEDIATE
CONNECTION CLOSE
The RMDPRB received the nack while cleaning up the
connection from PCOM.
2967
PCOM IMMEDIATE CONNECTION CLOSE TIMED OUT
RMDPRB has timed out to clean up a connection with
PCOM.
2968
THE CREATION OF A NEW BUILD FAILED IN
SOFTWARE MANAGEMENT
The creation of a new build failed in software
management.
2969
THE BUILD ID DOES NOT EXIST IN THE SOFTWARE
MANAGEMENT SYSTEM
The build ID does not exist in the software management
system.
2970
DELETE BUILD FAILED
This denotes that the delete build has failed.
2971
ACTIVATE BUILD FAILED
Activate build failed.
2972
232
SAVE NE FILES FAILED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Saving NE files failed.
2973
ILSWMAN CLI COMMAND OUTPUT FORMAT IS
ILLEGAL
An error code that indicates that IL_SWMAN CLI
commands output a bad format that cannot be parsed.
2974
THE MEASUREMENT REQUEST FOR STORAGE
ACCESS LATENCY SHOULD NOT BE FOR THE UNIT
WHICH IS NOT DISK UNIT.
The measurement for storage access latency is not for a
disk unit.
2975
HSS NOT UPDATED
HSS_NOT_UPDATED_EC is set when the HSS is present,
and there is no purge response arriving from the HSS.
2976
COPY BUILD FAILED
Copy new build has failed from the specified build.
2977
BUILD ID ALREADY BELONGS TO A BACKUP BUILD
This denotes that the build already belongs to a backup
build.
2978
BPS NAME IS ALREADY USED BY OTHER BPS
This denotes that the BPS name is already used by other
BPS.
2979
DUPLICATE BUILD EXIST
This denotes that a duplicate build exists.
2980
TARGET BACKUP BUILD FOR SYNC MISMATCH
This denotes a mismatch in the target backup build for
sync.
2981
THE BACKUP BUILD CONFIG IS ILLEGAL FOR
CURRENT OPERATION
The backup build config is illegal for the current operation.
2982
EXCHANGE BACKUP BUILD STATE FOR SYNC FAILED
This indicates that the exchange backup build state for the
sync has failed.
Issue: 30-0
2983
The NTP is disabled, and all NTP configuration changes
and queries are forbidden.
2984
SAVE NE LEVEL CONFIGURATION FAILED
DN987378
233
Error messages
General Error Messages of System
Saving NE level configuration failed.
2985
RESTORE NE LEVEL CONFIGURATION FAILED
The restore NE-level configuration has failed.
2986
SETTING OF MULTI-SESSION MONITORING FAILED
This denotes a request for the new monitoring session
when there is already a maximum alive session.
2987
This signifies that there is no NTP server configured.
2988
Invalid Userplane DCH/CCH monitoring type is received.
Valid values: call_based-1 or protocol based-0
This denotes that an Invalid Userplane DCH/CCH
monitoring type is received. The valid values are:
call_based-1 or protocol based-0.
2989
CHANGE BUILD STATUS FAILED
Change build status failed.
2990
CONNECTION ID CANNOT BE ALLOCATED ANYMORE
Additional connection ID can no longer be allocated.
2991
WCEL-HSPATOTINCREASESTEP CAN BE ENABLED
ONLY WHEN WCEL-HSPA128USERSPERCELL IS
ENABLED
WCEL-HSPATotIncreaseStep can be enabled only when
WCEL-HSPA128UsersPerCell is enabled.
2992
THE COMBINED AMOUNT OF CONFIGURED HSPA
SUBSCRIBER INCREASE STEPS EXCEEDS THE
LICENSED AMOUNT IN THE RNC
The combined amount of the configured HSPA subscriber
increase steps exceeds the licensed amount in the RNC.
2993
PROFILE RECORD DOES NOT EXIST
This denotes that the profile record does not exist.
2994
RULE RECORD DOES NOT EXIST
This denotes that the rule record does not exist.
2995
RULE RECORD ALREADY EXISTS
This denotes that the rule record already exists.
2996
PROFILE RECORD ALREADY EXISTS
This denotes that the profile record already exists.
234
DN987378
Issue: 30-0
General Error Messages of System
2997
Error messages
PROFILE IS ALREADY IN USE
This denotes that the profile is already in use.
2998
Preamble Signature or Cell Radius not compatible.
The BTS/cell cannot support the configured PRACH
preamble signatures, and the maximum cell radius
combination.
2999
No filesystem in the disk, or filesystem type is not wanted,
or disk partitions is not right.
This denotes one of three things: there is no file system in
the disk; the file system type is not wanted; or the disk
partitions are not right. This is mainly used in the LinDX
units that have a disk (GPLD and LOGU).
3000
SEGMENT PLMN ID USED INCORRECTLY IN
OPERATOR CONFIGURATION
The PLMN ID of the segment used in the configuration of
the primary or secondary operator in the operator pool is
incorrect and cannot be accepted for use in the shared
segment, but must be used in the dedicated segment.
3001
Received mon_upcmd_s in invalid state in monitoring
agents
This denotes the received mon_upcmd_s in invalid state in
monitoring agents.
3002
Sender pid is different from mon_upcmd_s sender pid
The sender PID is different from mon_upcmd_s sender
PID.
3003
Given premon command already exists in history list
The given premon command already exists in the history
list.
3004
Mon command history list reached max limit
The mon command history list has reached the max limit.
3005
Monitoring is already set for this service id and component
id
This denotes that monitoring is already set for this service
ID and component ID.
3006
Invalid monint command option received
This denotes an invalid monint command option was
received.
Issue: 30-0
DN987378
235
Error messages
General Error Messages of System
3007
Invalid version info in monitoring agent
This denotes an invalid version info in the monitoring
agent.
3008
Invalid logical address for the corresponding physical
address
This denotes an invalid logical address for the
corresponding physical address.
3009
Invalid proxy unit received
This denotes that an invalid proxy unit was received.
3010
Invalid physical address returned for specific unit index
This denotes that an invalid physical address is returned
for a specific unit index.
3011
Process nameserver registration failed
The process nameserver registration failed.
3012
order_family_restart_notice_r registration failed
The order_family_restart_notice_r registration failed.
3013
Session is active and again received the
mon_session_start
The session is active, and again received the
mon_session_start.
3014
Udp connection is closed and receiving the other
monitoring commands
The Udp connection is closed, and is receiving the other
monitoring commands.
3015
Invalid monitoring session id
This denotes an invalid monitoring session ID.
3016
Sender computer address is different from session owner
computer
The sender computer address is different from the session
owner computer.
3017
Sender process family is different from session owner
family
The sender process family is different from the session
owner family.
3018
236
Sender process id is different from session owner process
id
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The sender process ID is different from the session owner
process ID.
3019
Invalid monitoring type received. Valid values are legacy(0)
and call based(1)
This denotes that an invalid monitoring type was received.
The valid values are: legacy(0) and call based(1).
3020
Service id given in command does not exist
The Service ID given in the command does not exist.
3021
Udp connection creation failed towards emil
The Udp connection creation failed towards emil.
3022
Message version type is neither v10 nor v20 format
The message version type is neither v10 nor v20 format.
3023
Socket bind failed for monitoring agents
The socket bind failed for monitoring agents.
3024
Udp socket connection is already closed
The Udp socket connection is already closed.
3025
Received session id is not matcing with stored session id
after decryption
The received session ID does not match with the stored
session ID after decryption.
3026
prb_restart_notice_s received with unexpected family_id
A prb_restart_notice_s was received with an unexpected
family_id.
3027
Too many parameters received in monitoring command
This denotes that too many parameters were received in
the monitoring command.
3028
Not enough parameters received in monitoring command
This denotes that not enough parameters are received in
the monitoring command.
3029
Invalid snap_item value received in monitoring command
This denotes an invalid snap_item value received in the
monitoring command.
3030
Issue: 30-0
Invalid optional param value received in monitoring
command
DN987378
237
Error messages
General Error Messages of System
This denotes that an invalid optional param value is
received in the monitoring command.
3031
Multiple -f options are not allowed
This denotes that multiple -f options are not allowed.
3032
Multiple -p options are not allowed
This denotes that multiple -p options are not allowed.
3033
Multiple -t options are not allowed
This denotes that multiple -t options are not allowed.
3034
Multiple -s options are not allowed
This denotes that multiple -s options are not allowed.
3035
Multiple -c options are not allowed
This denotes that multiple -c options are not allowed.
3036
Multiple -w options are not allowed
This denotes that multiple -w options are not allowed.
3037
Multiple -k1 options are not allowed
This denotes that multiple -k1 options are not allowed.
3038
Multiple -k2 options are not allowed
This denotes that multiple -k2 options are not allowed.
3039
Multiple -k3 options are not allowed
This denotes that multiple -k3 options are not allowed.
3040
Multiple -k4 options are not allowed
This denotes that multiple -k4 options are not allowed.
3041
Multiple -k5 options are not allowed
This denotes that multiple -k5 options are not allowed.
3042
Multiple -k6 options are not allowed
This denotes that multiple -k6 options are not allowed.
3043
Multiple -k7 options are not allowed
This denotes that multiple -k7 options are not allowed.
3044
Multiple -k8 options are not allowed
This denotes that multiple -k8 options are not allowed.
238
DN987378
Issue: 30-0
General Error Messages of System
3045
Error messages
Multiple -k9 options are not allowed
This denotes that multiple -k9 options are not allowed.
3046
Multiple -k10 options are not allowed
This denotes that multiple -k10 options are not allowed.
3047
Multiple -m1 options are not allowed
This denotes that multiple -m1 options are not allowed.
3048
Multiple -m2 options are not allowed
This denotes that multiple -m2 options are not allowed.
3049
Multiple -m3 options are not allowed
This denotes that multiple -m3 options are not allowed.
3050
Multiple -m4 options are not allowed
This denotes that multiple -m4 options are not allowed.
3051
Multiple -m5 options are not allowed
This denotes that multiple -m5 options are not allowed.
3052
Multiple -m6 options are not allowed
This denotes that multiple -m6 options are not allowed.
3053
Multiple -m7 options are not allowed
This denotes that multiple -m7 options are not allowed.
3054
Multiple -m8 options are not allowed
This denotes that multiple -m8 options are not allowed.
3055
Multiple -m9 options are not allowed
This denotes that multiple -m9 options are not allowed.
3056
Multiple -m10 options are not allowed
This denotes that multiple -m10 options are not allowed.
3057
Multiple -m11 options are not allowed
This denotes that multiple -m11 options are not allowed.
3058
Multiple -m12 options are not allowed
This denotes that multiple -m12 options are not allowed.
3059
Multiple -m13 options are not allowed
This denotes that multiple -m13 options are not allowed.
Issue: 30-0
DN987378
239
Error messages
General Error Messages of System
3060
Multiple -m14 options are not allowed
This denotes that multiple -m14 options are not allowed.
3061
Multiple -m15 options are not allowed
This denotes that multiple -m15 options are not allowed.
3062
Multiple -m16 options are not allowed
This denotes that multiple -m16 options are not allowed.
3063
Requested server process has no instance
The requested server process has no instance.
3064
Requested server type match not found in the list
The requested server type match was not found in the list.
3065
Missing or Invalid server type requested
A missing or invalid server type has been requested.
3066
Give both Service ID & Component ID for mon command,
both or none for premon command
Gives both the Service ID and Component ID for mon
command, and for both or none for premon command.
3067
Invalid -c value. Valid range 0-0xFFFFFFFF
Invalid -c value; valid range is 0-0xFFFFFFFF
3068
APN AND QCI ARE APPLICAPLE ONLY FOR S11
INTERFACE
APN and QCI are applicable only for S11 interface.
3069
NO PAGING ATTEMPS DEFINED IN ANY LEVEL
No paging attempts are defined in any level.
3070
HSPA SUBSCRIBER INCREASE LICENSE FEATURE
STATE IS NOT ON
The HSPA Subscriber increase license feature state is not
ON.
3071
LINK SYNCHRONIZATION FAILURE
A high speed link that connects to spare SFU
synchronization failure.
3072
Loop is Not Found in RNW Database
This error code is set when the loop has not been created
in the RNW database.
240
DN987378
Issue: 30-0
General Error Messages of System
3073
Error messages
ABIS PCM is not present in RNW Database.
This error code is set when the Abis PCM has not been
added into the RNW Loop database.
3074
LoopBack PCM is not present in RNW Database.
This error code is set when the LoopBack PCM has not
been added into the RNW Loop database.
3075
Second Protecting PCM is not present in RNW Database.
This error code is set when the 2nd Protecting PCM has
not been added into the RNW Loop database.
3076
First Protecting PCM is not present in RNW Database.
This error code is set when the 1st Protecting PCM has not
been added into the RNW Loop database.
3077
LOOP BCF is not present in RNW Database.
This error code is set when the BCF has not been added
into the RNW Loop database.
3078
SBIT is not present in RNW Database.
This error code is set when the Synch Bit has not been
added into the RNW Loop database.
3079
No More AS7 is available
This error code is set when there is no free AS7 terminal to
create the Pilot Bit Uplink Connections.
3080
HSRACHENABLED VALUE MISMATCH WITH
RACHPREAMBLESIGNATURES VALUE
If HSRACHEnabled is set as Disabled, the
RACHPreambleSignatures cannot have defined values for
HS-RACH signatures.
3081
CELL UNLOCKING IS PREVENTED DUE TO MISSING
RACH CAPACITY INCREASE LICENSE OR
PARAMETER MISCONFIGURATION
Withthe configured RACHPreambleSignatures parameter
values, the cell cannot be unlocked if the RACH capacity
increase is missing or a parameter is not configured
correctly.
3082
OPERATION NOT ALLOWED FOR SRAN BTS
Certificate management operation is not allowed for
Multiradio 10 BTS, which is in SRAN mode.
Issue: 30-0
DN987378
241
Error messages
General Error Messages of System
3083
BCF EXTERNAL INPUTS FOR SRAN BTS CAN NOT BE
CONFIGURED VIA BSC
The BCF external inputs for SRAN BTS are not configured
thru BSC.
3084
BCF OUTPUTS FOR SRAN BTS CAN NOT BE
CONFIGURED VIA BSC
The BCF Outputs for SRAN BTS are not configured thru
BSC.
3085
SRAN BTS IS NOT CONFIGURED TO USE CORRECT
PACKET ABIS TYPE
SRAN BTS is not configured to use correct packet abis
type
3086
CLOCK SOURCE FOR SRAN BTS SHALL BE BSSTOP
When BSS Synchronisation is used for SRAN BTS, the
only allowed clock source value in BSC is BSSTOP.
3087
SCF FILE ACTIVATION OR UPLOAD FOR SRAN BTS
NOT ALLOWED
SCF file download operation from BSC to SRAN BTS or
SCF file upload operation from SRAN BTS is not allowed.
3088
SW MANAGEMENT OF SRAN BTS IS NOT ALLOWED
VIA BSC
The SW management of SRAN BTS is not allowed thru
BSC.
3089
BUILD IDENTIFIER SRAN IS RESERVED BY SYSTEM
The build identifier SRAN is reserved by the system.
3090
SYNCHRONISATION IS NOT CONFIGURED
CORRECTLY AT BTS SITE
The synchronization is not configured correctly in the BTS
site.
3091
This denotes an invalid build type error.
3092
This denotes an \"RNC SRV not exist\" error.
3093
This denotes an RNC SRV conflict error.
3094
NORMAL TRX CREATION FAILURE IN STANDBY BTS
This error code is displayed when a normal TRX creation
is attempted in a standby BTS.
242
DN987378
Issue: 30-0
General Error Messages of System
3095
Error messages
THE REQUESTED ACTION WAS NOT PERFORMED
DUE TO THE GROUP CALL STATUS
The requested action was not performed because of the
group call status.
3096
The LRMPRB has detected an invalid core status.
3097
HSRACHENABLED OR HSPA72USERSPERCELL
VALUE MISMATCH WITH HSRACHCOMMONEDCHRES
VALUE
If HSRACHEnabled or HSPA72UsersPerCell has a value
of Disabled, HSRACHCommonEDCHRes cannot have
defined values for the number of Common E-DCH
Resources of the HS-RACH configuration in the cell.
3098
CELL UNLOCK PREVENTED DUE TO HS CELL_FACH
ENHANCED FEATURE STATE AND
HSRACHCOMMONEDCHRES VALUE MISMATCH
With the configured HSRACHCommonEDCHRes
parameter values, the cell cannot be unlocked if High
Speed Cell_FACH Enhanced is missing, or the parameter
is misconfigured.
3099
HIGH SPEED CELL_FACH ENHANCED IS NOT
SUPPORTED BY BTS
The BTS/cell has received the number of HS-RACH users
per cell, but cannot support the configured enhanced HSRACH users per cell (common E-DCH resources per cell).
3100
Invalid checkpoint time received for maximum overload
There is an invalid checkpoint time received for maximum
overload in DMA.
3101
Invalid sequential value received for maximum overload
There is an invalid sequential value received for maximum
overload in DMA.
3102
Invalid threshold value received for maximum overload
There is an invalid threshold value received for maximum
overload in DMA.
3103
Invalid checkpoint time received for minimum overload
There is an invalid checkpoint time received for minimum
overload in DMA.
3104
Invalid sequential value received for minimum overload
There is an invalid sequential value received for minimum
overload in DMA.
Issue: 30-0
DN987378
243
Error messages
General Error Messages of System
3105
Invalid threshold value received for minimum overload
This denotes that an invalid threshold value was received
for minimum overload in DMA.
3106
Received minimum threshold value is more than max
threshold
The received minimum threshold value is more than the
maximum threshold in DMA.
3107
Received minimum checkpoint value is more than max
checkpoint
The received minimum checkpoint value is more than the
maximum checkpoint in DMA.
3108
OLD PCM NOT FOUND IN RNW CONFIGURATION
This error code is set when an old PCM number is not part
of the RNW configuration.
3109
PILOT BIT IS ALREADY CONFIGURED FOR SOME
OTHER LOOP
This error code is set when the received pilot bit is already
configured for some other loop.
3110
TSL range is already set for some other BCF in the same
loop
This error code is set when the received TSL range is
already set for some other BCF in the same loop.
3111
Synch bit is already configured for the loop
This error code is set when a synch bit is already
configured for the loop.
3112
LOOP IS ALREADY CONFIGURED
This error code is set when a loop has been already
configured.
3113
AbisPCM is not configured for the loop
This error code is set when AbisPCM is not configured for
the loop.
3114
PILOT BIT IS NOT CONFIGURED FOR THE LOOP BCF
This error code is set when a pilot bit is not configured for
the loop BCF.
3115
Old PCM is already configured for some loop
This error code is set when an old PCM is already
configured for some loop.
244
DN987378
Issue: 30-0
General Error Messages of System
3116
Error messages
FAILURE IN LOOP UPDATE AT M4LPRO
This error code denotes a failure in the loop update at
M4LPRO.
3117
FAILURE IN PILOT BIT CONNECTION ESTABLISHMENT
This error code is set when there is a failure in the pilot bit
connection establishment.
3118
FAILURE IN LOOP CONNECTION ESTABLISHMENT
This error code is set when there is a failure in the loop
connection establishment.
3119
FAILURE IN SYNCH BIT CONNECTION
ESTABLISHMENT
This error code is set when there is a failure in the synch
bit connection establishment.
3120
Failure in Uplink Connection Establishment
This error code is set when there is a failure in the uplink
connection establishment.
3121
FAILURE IN DOWNLINK CONNECTION
ESTABLISHMENT
This error code is set when there is a failure in the
downlink connection establishment.
3122
ISSUE WITH PDH TO ILP MODIFICATION SCENARIO
This error code is set when there is some issue with PDH
to ILP modification scenario.
3123
REQUEST FAILED RNC RESILIENCY BKPRNC OBJECT
IS NOT CONFIGURED AT PRPRNC
Request failed - The RNC resiliency is not configured at
PRPRNC.
3124
No DAP available on the requested Abis PCM
This error code is set when there is no DAP available on
the requested ABIS PCM.
3125
WDEV COLLECTION FULL
The WDEV collection is full.
3126
WDEV OBJECT NOT FOUND
The WDEV object is not found.
3127
Issue: 30-0
WDEV OBJECT ALREADY CREATED
DN987378
245
Error messages
General Error Messages of System
The WDEV object is already created.
3128
NO ANSWER RECEIVED FROM JELPPI IN TIME
No answer is received from JELPPI in time.
3129
WCEL-WCDMALTELoadBalEnabled can be enabled only
when WCEL-IncomingLTEISHO is enabled.
WCEL-WCDMALTELoadBalEnabled can be enabled only
when WCEL-IncomingLTEISHO is enabled.
3130
WCEL-WCDMALTELoadBalEnabled can be enabled only
if at least one ADJE has been configured for the cell.
WCEL-WCDMALTELoadBalEnabled can be enabled only
if at least one ADJE has been configured for the cell.
3131
WCEL-WCDMALTELoadBalEnabled can be enabled only
when either RAN2264 or RAN2717 is enabled.
WCEL-WCDMALTELoadBalEnabled can be enabled only
when either WCEL-LTEHandoverEnabled or WCELSmartLTELayeringEnabled is enabled.
3132
FILE STATUS CHANGE PARTLY OK
The file status change is partly ok.
3133
RNCSRV OBJECT CREATION NOT POSSIBLE IF
RNCSRV ID IS EQUAL TO BKPRNC ID
The rncsrv object creation is not possible if the rncsrv ID is
the same as the bkprnc ID.
3134
FBPP OPERATIONS ARE NOT ALLOWED IN BACKUP
BSC
FBPP operations are not allowed in the Backup BSC.
3135
OPERATION IS NOT ALLOWED IN BACKUP BSC
Operation is not allowed in the backup BSC.
3136
OPERATION IS NOT ALLOWED IN PROTECTED BSC
Operation is not allowed in the Protected BSC.
3137
NON DUAL HOMED BLOCKED IN BACKUP BSC
Non-dual homed BCF is blocked in the backup BSC
because of the BSC switchover of the Network Resiliency
for mcBSC.
3138
246
PARAMETERS FOR BACKUP AND PROTECTED BSC
CANNOT BE IN SAME BSC
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Parameters for backup and protected BSC cannot be
given in the same BSC.
3139
EITHER BACKUP OR PROTECTED BSC ROLE CAN BE
DEFINED FOR ONE BSC
Either a backup or a protected BSC role can be defined for
one BSC.
3140
BSC ID NOT UNIQUE FOR BSC ASSOCIATION
The BSC ID is not unique for the BSC association.
3141
BSC IP ADDRESS NOT UNIQUE FOR BSC
ASSOCIATION
The BSC IP address is not unique for the BSC association.
3142
MAXIMUM AMOUNT OF BSC ASSOCIATIONS
EXCEEDED
The maximum amount of BSC associations has exceeded.
3143
BACKUP IS ACTIVE
The requested operation cannot be performed because
BkBSC has an active backup.
3144
DATA SYNCRONIZATION BLOCKED
PrBSC synchronization is in blocked state.
3145
IP CONNECTION TO PRBSC HAS FAILED
The IP connection to PrBSC has failed.
3146
SW LEVEL CHECK FAILED
The denotes that the SW-level check failed.
3147
DATA ADAPTATION FAILED
Data adaptation failed.
3148
NETWORK RESILIENCY FOR MCBSC FEATURE NOT IN
USE
Network Resiliency for the mcBSC feature is not in use.
3149
INCORRECT BSC ACTIVITY MODE OR SERVICE
STATUS FOR OPERATION
Incorrect BSC activity mode or service status for the
requested operation.
3150
SYNCHRONIZATION IS PENDING
This denotes that the synchronization is pending.
Issue: 30-0
DN987378
247
Error messages
General Error Messages of System
3151
PBSC OBJECT NOT FOUND
This denotes that the Protected BSC is not found.
3152
BBSC OBJECT NOT FOUND
Backup BSC is not found.
3153
NETWORK RECILIENCY HANDLER HAS
ENCOUNTERED INTERNAL ERROR
This denotes that the Network Reciliency Handler has
encountered an internal error.
3154
NO ONGOING SYNCHRONIZATION
There is no ongoing synchronization.
3155
TERMINATION IS ONGOING
Termination is ongoing.
3156
SW BUILD MANAGEMENT OPERATION ONGOING
SW build management operation ongoing
3157
ANOTHER NETWORK RESILIENCY OPERATION
ONGOING
This denotes that another network resiliency operation is
ongoing. Check the service_status of the PBSC object.
3158
BKPRNC OBJECT CREATION NOT POSSIBLE IF
BKPRNC ID IS EQUAL TO PRNC ID
The BKPRNC object creation is not possible if the
BKPRNC ID is the same as the STPRNC or PRPRNC ID.
3159
THE CONFIGURED MPS VALUE IS NOT CONFIGURED
IN THE RELEVANT PRIORITY LIST
The configured MPS value is not configured in the relevant
priority list.
3160
RELEASE UPGRADE FAILED DURING RNWDB
CONVERSION BECAUSE LAST PLAN ACTIVATION OR
ROLLBACK WAS INTERRUPTED.
The release upgrade failed during RNW database
conversion because the last RNW plan activation or
rollback was not successfully completed. Full consistency
check is required for recovery.
3161
THE VALUE OF ARPPR, EMLPPPR, AND CALLPR IS
ALREADY MAPPED TO ONE PAGPR VALUE
The value of ARPPR, EMLPP, and CALLPR is already
mapped to one PAGPR value.
248
DN987378
Issue: 30-0
General Error Messages of System
3162
Error messages
CREATION OF IP CONNECTIVITY FILE FAILED
This denotes that the creation of an IP connectivity file has
failed.
3163
This denotes that the same feature is already configured
for the same TAC for device detection.
This denotes that the same feature is already configured
for the same TAC for device detection.
3164
This denotes a duplicated TAC value in WDEV.
This denotes a duplicated TAC value in WDEV.
3165
This denotes a duplicated feature in the black and white
list.
This denotes a duplicated feature in the black and white
list.
3166
LCSINTERFACEOPTION OR OPERATIONALMODE
VALUE MISMATCH WITH
GLONASSFUNCTIONALITYENABLED VALUE
If LCSInterfaceOption has value None or OperationalMode
has value.
3167
GLONASSFUNCTIONALITYENABLED CANNOT BE
ENABLED DUE TO MISSING OR TOO LOW GNSS
CAPACITY LICENSE
The GLONASSFunctionalityEnabled cannot have a value
Enabled if GNSS capacity license is missing or too low.
3168
FILE OR DIRECTORY ONLY EXISTS IN ONE WDU
The file or directory only exists in one WDU.
3169
THE DEFAULT BUILD IS NOT A BACKUP BUILD OF
BPS.
The default build is not a backup build of BPS.
3170
CANCELED LICENCE LIST MISSING
The canceled license list is missing.
3171
CANCELED LICENCE LIST CORRUPT
The canceled license list is corrupt.
3172
CANCELED LICENCE LIST EXCEEDING LIMIT
The canceled license list capacity exceeded the maximum
number limit.
3173
Issue: 30-0
CANCELED LICENCE LIST BLOCKING INSTALLATION
DN987378
249
Error messages
General Error Messages of System
The canceled license list blocking installation of the license
3174
NETWORK RESILIENCY OPERATION INTERRUPTED
BY BSC RESET
The Network Resiliency operation has been interrupted by
BSC reset.
3175
PBSC ID AND BBSC ID OBJECT IDENTIFIER SHALL
DIFFER FROM OWN BSC ID
PBSC ID and BBSC ID object identifiers shall be different
from own BSC ID.
3176
PROTECTED BSC ID DIFFERS FROM OWN BSC ID
Given protected BSC ID differs from own BSC ID.
3177
ENHANCED FAST RETURN TO LTE FEATURE IS NOT
IN USE IN BSC
The Enhanced Fast Return to LTE feature is not enabled in
the BSC. Either the feature license is not valid or the
feature status is in disabled state.
3178
THE BTS DOES NOT SUPPORT THE FREQUENCY
CHANGE WITHOUT RESET OR IT IS NOT ABLE TO
REPORT ABOUT THE SUPPORT
The BTS does not support the frequency change without
reset or it is not able to report about the support.
3179
THE FREQUENCIES OF ALL THE CELLS IN THE SAME
LAYER IN THE BTS MUST BE CHANGED IN THE SAME
OPERATION
The frequencies of all the cells in the same layer in the
BTS must be changed in the same operation.
3180
THE NEW FREQUENCY SHALL BE IN THE SAME BAND
AS THE OLD FREQUENCY
The new frequency shall be in the same band as the old
frequency.
3181
SYNHRONIZATION IS ALREADY ONGOING
This denotes that the synchronization is already ongoing.
3182
STOP OPERATION IS NOT ALLOWED IN TEMPORARY
RESOURCE CLEAN UP PHASE OF ADAPTATION.
This means that the stop operation is not allowed in the
temporary resource clean up phase of the adaptation.
3183
250
IP CONNECTIVITY TEST FILE OR SOURCE IP NOT
FOUND
DN987378
Issue: 30-0
General Error Messages of System
Error messages
This denotes that the IP connectivity test file or source IP
is not found.
3184
IP CONNECTIVITY TEST ABORT FAILED
This denotes that the IP connectivity test abort has failed.
3185
IP CONNECTIVITY TEST NOT STARTED
This denotes that the IP connectivity test has not started.
3186
IP CONNECTIVITY TEST FAILED AT PLATFORM
This denotes that the IP connectivity test failed at platform.
3187
IP CONNECTIVITY TEST SUMMARY REPORT NOT
AVAILABLE
This denotes that the IP connectivity test summary report
is not available.
3188
SCRAMBLING CODE REQUIRED
If the Blind 2G to 3G Reselection license is OFF/CONF, it
is not possible to have WCDMA adjacency configuration
without SCC parameter.
3189
ADJACENCY WITHOUT SCRAMBLING CODE EXISTS
When adjacency without scrambling code already exists, it
is not possible to configure another adjacency for the same
UARFCN with valid scrambling code in the same segment.
3190
ADJACENCY WITH VALID SCC EXISTS
When adjacency with scrambling code already exists, it is
not possible to configure another adjacency without
scrambling code for the same UARFCN in the same
segment.
3191
SCC MODIFICATION TO VALUE 512 IS NOT ALLOWED
The scrambling code for any WCDMA adjacency cannot
be modified to one without scrambling code.
3192
NO REPLY FROM ASSOCIATED BSC
This denotes that the controlled BSC switchover cannot
start because the associated BSC does not reply back.
3193
ASSOCIATED BSC IS ACTIVE AND SERVING THE
RADIO NETWORK
This denotes that the associated BSC is active and serving
the radio network.
3194
Issue: 30-0
CONFIGURATION PARTIALLY COMPLETED
DN987378
251
Error messages
General Error Messages of System
PrBSC configuration is partially completed in the BkBSC.
To correct this, reconfigure IP mapping and re-trigger
configuration commit operation to complete the
configuration.
3195
CONFIGURATION NOT COMPLETED
PrBSC configuration is not completed in the BkBSC. To
correct this, reconfigure IP mapping and re-trigger
configuration commit operation to complete the
configuration.
3196
THE LENGTH OF AES KEY IS ERROR
This denotes an aes set key length set error.
3197
ISO97971 PAD FAILED
This denotes that iso9797 method pad failed.
3198
ISO97971 UNPAD FAILED
This denotes that the iso9797 method unpad failed.
3199
SET AES ENCKEY FAIL EC
This denotes that the set aes encrypt key failed.
3200
SET AES DECKEY FAIL EC
This denotes that the set aes decrypt key failed.
3201
MAXIMUM ALLOWED DIGITS FOR EMERGENCY
NUMBERS ARE EXCEEDED.
The maximum allowed digits for emergency numbers are
exceeded.
3202
ONLY ZI4 COMMAND CAN BE EXECUTED BEFORE KI
HAS CONFIGURATED
This denotes that only ZI4 Command can be executed
before KI has configurated.
3203
MANUAL WEIGHTING FOR MULTIPOINT GB FEATURE
IS NOT IN USE IN BSC
The manual weighting for Multipoint Gb feature is not
enabled in BSC. Either the feature license is not valid, or
the feature status is in disabled state.
3204
NRR IS NOT SUPPORTED WITH MANUAL WEIGTHING
FOR MULTIPOINT GB
This denotes that normal round-robin load balancing
technique is not supported with manual weighting for
multipoint Gb.
252
DN987378
Issue: 30-0
General Error Messages of System
3205
Error messages
FAIL TO READ RESILIENCY CONFIG FILE
This denotes the failure to read the resiliency config file.
3206
HSPANRTOVERNRTENABLED CAN BE ENABLE ONLY
WHEN HSPAQOSENABLED AND PBSPOLICY ARE
ENABLE
HSPANRTOverNRTEnabled can be enabled only when
HSPAQoSEnabled and PBSpolicy are enabled.
3207
HSPAQOSENABLED CANNOT BE DISABLE WHEN
HSPANRTOVERNRTENABLED IS NOT DISABLE
HSPAQoSEnabled cannot be disabled when
HSPANRTOverNRTEnabled is not disabled.
3208
PBSPOLICY CANNOT BE DISABLE WHEN
HSPANRTOVERNRTENABLED IS NOT DISABLE
PBSPolicy cannot be disabled when
HSPANRTOverNRTEnabled is not disabled.
3209
COMBINATION OF WSProfileRelatedIUO
SubscriberProfilePLMNId AND SPID IN WSP NOT
UNIQUE
The combination of WSProfileRelatedIUO,
SubscriberProfilePLMNId, and SPID in the WSP object
must be unique.
3210
DedicatedPriorityLevel VALUE NOT UNIQUE WITHIN ALL
WDP IN ONE WSP
WDP-DedicatedPriorityLevel value must be unique within
all subscribers\' specific priorities associated with a certain
Subscriber Profile ID.
3211
WDP WITH GSM RADIO ACCESS TECHNOLOGY
EXCEEDS 3 IN ONE WSP
GSM or GSM1900 radio access technology can occur for a
maximum of 3 times within the subscriber\'s specific
priorities associated with a certain Subscriber Profile ID.
3212
NUMBER OF LTE ARFCN EXCEEDS 8 WITHIN ONE
WDP OR 32 WITHIN ONE WSP
The maximum number of LTE carrier frequencies is 8
within one subscriber\'s specific priority level, and 32 within
all subscribers\' specific priorities associated with a certain
Subscriber Profile ID.
3213
Issue: 30-0
NUMBER OF WCDMA ARFCN EXCEEDS 8 WITHIN ONE
WDP OR 16 WITHIN ONE WSP
DN987378
253
Error messages
General Error Messages of System
The maximum number of WCDMA carrier frequencies is 8
within one subscriber\'s specific priority level, and 16 within
all subscribers\' specific priorities associated with a certain
Subscriber Profile ID.
3214
AdjLThreslow2 AND AdjLThreshigh2 ASSOCIATE WITH
ONE DEDICATED PRIORITY MISMATCH
If any of the LTE frequencies within one WDP instance
(WDP-ARFCN) is defined as neighbouring E-UTRA
frequency in LTE adjacencies (ADJL-AdjLEARFCN) under
a WCEL instance, and any value different from the special
value (32 dB) is set to both HOPL-AdjLThreshigh2 and
HOPL-AdjLThreslow2 in some of those LTE adjacencies
under the WCEL instance, it must be checked that a value
different from the special value (32 dB) is set to both
HOPL-AdjLThreshigh2 and HOPL-AdjLThreslow2 in all
those LTE adjacencies under the WCEL instance in
question.
3215
WSP OBJECT NOT FOUND
This denotes that the WSP object was not found.
3216
WDP OBJECT NOT FOUND
This denotes that the WDP object was not found.
3217
WSP OBJECT ALREADY CREATED
This denotes that the WSP object was already created.
3218
WDP OBJECT ALREADY CREATED
This denotes that the WDP object was already created.
3219
TRANSITION TO SE STATE IS NOT ALLOWED
BECAUSE REDUNDANT TBU IS POWER OFF
When WO-EX TBU is powered off, TE-EX TBU is not
allowed to transit to SE state. Otherwise, there will be no
timing signal for the whole system, and thus the system
will restart.
3220
ONLY I4/AH/QNI command can be executed before
executing I4C command
This denotes that only I4/AH/QNI command can be
executed before executing an I4C command.
3221
WCEL-MOCNCAENABLED CAN ONLY BE ENABLED IF
FMCG-IMSIBASEDGSMHO IS NOT SET WITH 0
WCEL-MOCNCAENABLED CAN ONLY BE ENABLED IF
WCEL-RTFMCGIDENTIFIER IS DEFINED AND
CORRESPONDING FMCG-IMSIBASEDGSMHO IS 1.
254
DN987378
Issue: 30-0
General Error Messages of System
3222
Error messages
WCEL-MOCNCAENABLED CAN ONLY BE ENABLED IF
WCEL-HSPAQOSENABLED IS SET AS ENABLED
WCEL-MOCNCAEnabled is not allowed to be set to
Enabled if WCEL-HSPAQoSEnabled has a value of
Disabled.
3223
WCEL-MOCNCAENABLED CAN ONLY BE ENABLED IF
RNFC-MOCNENABLED IS SET AS ENABLED
WCEL-MOCNCAEnabled is not allowed to be set to
Enabled if RNFC-MOCNenabled has a value of Disabled.
3224
WCEL-MOCNCAENABLED AND WCELDBANDHSDPAENABLED CAN NOT BE ENABLED
SIMULTANEOUSLY
WCEL-MOCNCAEnabled is not allowed to be set to
Enabled if WCEL-DBandHSDPAEnabled has a value of
Enabled.
3225
WCEL-MOCNCAENABLED AND WCELMCELLHSDPAENABLED CAN NOT BE ENABLED
SIMULTANEOUSLY
WCEL-MOCNCAEnabled is not allowed to be set to
Enabled if WCEL-MCellHSDPAEnabled has a value of
Enabled.
3226
WCEL-MOCNCAENABLED AND WCEL-ICRENABLED
CAN NOT BE ENABLED SIMULTANEOUSLY
WCEL-MOCNCAEnabled is not allowed to be set to
Enabled if WCEL-ICREnabled has a value of Enabled.
3227
BSC was not found in IP mapping file.
This denotes that there is no IP address mapped for the
given BSC. Use ZD6G command to add the mapping
information.
3228
WCEL-MOCNCAENABLED IS SET TO ENABLED, BUT
MOCN CA FEATURE IS NOT SUPPORTED BY BTS
This denotes that the WCEL-MOCNCAEnabled is set to
ENABLED, but MOCN CA FEATURE is not supported by
the BTS.
3229
This denotes a FILE READ ERROR.
3230
This denotes an INVALID CONFIGURATION.
3231
This denotes a GENERAL PROCESSING ERROR.
3232
IPDU SWITCHOVER
This denotes IPDU switchover.
Issue: 30-0
DN987378
255
Error messages
General Error Messages of System
3233
GISU SWITCHOVER
This denotes GISU switchover.
3234
WSP ASSOCIATION EXISTS
The IUO object is not allowed to be deleted if any WSP
object has an associated WSProfileRelatedIUO to it.
3235
SOME WDPS EXIST UNDER THE WSP TO BE
DELETED
The object WDP shall be deleted first, and then WSP
object could be deleted.
3236
WSP COLLECTION FULL
This denotes that the WSP collection is full.
3237
WDP COLLECTION FULL
This denotes that the WDP collection is full.
3238
MOCNCA CANNOT BE ACTIVATED BECAUSE THE
MOCNCA LICENSE STATE IS CONFIG/OFF INSTEAD
OF ON
MOCNCA CANNOT BE ACTIVATED BECAUSE THE
MOCNCA LICENSE STATE IS CONFIG/OFF INSTEAD
OF ON
3239
ICR CANNOT BE ACTIVATED BECAUSE THE ICR
LICENSE STATE IS CONFIG/OFF INSTEAD OF ON
ICR CANNOT BE ACTIVATED BECAUSE THE ICR
LICENSE STATE IS CONFIG/OFF INSTEAD OF ON
3240
MOCN CA CONFIGURATION ERROR.
MOCN CA CONFIGURATION ERROR
3241
when create more than 8 wdps in one wsp, this error code
will be reported.
3242
CURRENT COMMAND CANNOT BE EXECUTED
BEFORE EXECUTING I4C COMMAND
This denotes that only some specified commands can be
executed before executing an I4C command.
3243
RNFC-NBAPLBSERVRESTRENABLED CAN ONLY BE
ENABLED IF RNFC-BTSLOADINDSEL IS (PRIVATE
CAUSE CODE IS USED)
This denotes that RNFC-NBAPLBServRestrEnabled can
only be enabled if RNFC-BTSLoadIndSel is (Private cause
code is used).
256
DN987378
Issue: 30-0
General Error Messages of System
3244
Error messages
WCEL-MOCNCAENABLED CAN NOT BE ENABLED IF
RNFC-PBSPOLICY HAS VALUE 1.
THIS DENOTES THAT WCEL-MOCNCAENABLED CAN
NOT BE ENABLED IF RNFC-PBSPOLICY HAS A VALUE
OF 1.
3245
WCEL-MOCNCAENABLED CAN ONLY BE ENABLED ON
A MOCN CELL
THIS DENOTES THAT WCEL-MOCNCAENABLED CAN
ONLY BE ENABLED ON AN MOCN CELL.
4001
DISKLOG IS FULL
The disklog is full. Either the saver hand of DBSMAN has
not time to empty it, or the saver hand does not function.
DBSMAN can not receive updated until there is room in
the dislog. The operator can send to DBSMAN an
instruction to empty the disklog with the message
move_log_on_files_s.
4333
ZERO NOT ALLOWED FILE NUMBER
Zero is not an allowed file number.
8000
ROUTINE MEASUREMENT EVENT IS ALREADY
STARTED
MCALEN has requested ROTEST to start a routine
measurement, but ROTEST has detected that such a
measurement already is in progress.
8001
ROUTINE MEASUREMENT EVENT IS RUNNING
The routine measurement is in progress.
8002
ROUTINE MEASUREMENT EVENT IS NOT RUNNING
The routine measurement is not in progress. This error
code can be received when an attempt has been made to
stop the routine measurement.
8003
ROUTINE MEASUREMENT EVENT EXISTS
The routine measurement event has been defined.
MCALEN returns this error code if an attempt has been
made to define a routine measurement with an
identification that is in use.
8004
ROUTINE MEASUREMENT EVENT WAS NOT FOUND
The routine measurement event was not found in the
RTSPAR file of MCALEN.
8005
Issue: 30-0
ROUTINE MEASUREMENT EVENT IDENTIFIER IS
AMBIGUOUS
DN987378
257
Error messages
General Error Messages of System
The identifier of a routine measurement event does not
unambiguously refer to a measurement event, in other
words several identifiers match with the defined identifier.
8006
ROUTINE MEASUREMENT EVENT IS ALREADY
ACTIVE
The routine measurement event already is active in the
RTSPAR file.
8007
ROUTINE MEASUREMENT EVENT IS ALREADY
INACTIVE
The routine measurement event already is marked as
inactive.
8008
ROUTINE MEASUREMENT EVENT WAS INTERRUPTED
The routine measurement event is interrupted.
9000
RECEIVED MESSAGE IS OF WRONG LENGTH
The received message is of wrong length.
9001
MESSAGE NOT RECEIVED DUE TO TIME-OUT
It has not been possible to receive a message due to timeout.
9002
NO OMU ASS CHANNELS
No ASS-channels found for the OMU.
9003
ILLEGAL CODE FOR OMU ASS CHANNEL
The type of the OMU ASS-channel to be searched for is
incorrect, in other words other than EAL, LTEST or
reserved (TSL_BASED).
9004
NO OMU EAL ASS CHANNEL
The EAL-ASS-channels of the OMU are not found.
9005
NO OMU LTEST ASS CHANNEL
The LTEST-ASS-channels of the OMU are not found.
9006
NO SIGNALLING FAMILY
No CCS or channel-specific signalling family is connected
with the defined computer unit type.
9007
NO SIGNALLING TYPE
No corresponding CCS or channel-specific signalling unit
is found for the defined family identifier.
9008
258
UNIT IN SE-NH SUBSTATE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The computer unit is not equipped.
9009
NO ET PCM FOUND
No external PCM circuit is found.
9010
LOGICAL COMPUTER ADDRESS NOT FOUND
No logical address is found for the defined computer unit
which is to serve an external PCM-circuit.
9011
LST CONNECTED PCM CIRCUIT NOT FOUND
An internal PCM-circuit served by the LSU or CAC is not
found.
9012
NO LSU COMPUTER UNIT IN THE GIVEN MB
ADDRESS
No LSU unit is found in the given physical address.
9013
ACSERV PROGRAM BLOCK NOT FOUND
An internal PCM-circuit served by the ACSERV program
block is not found; for this reason no ASS-index can be
returned to the user.
9014
PCM WITH COMMON CHANNEL SIGNALLING NOT
FOUND
The DX exchange in question is not a CCS exchange.
9015
NO RESERVED ASS CHANNELS
The OMU has no permanent (reserved) ASS-channels.
9016
NO SIGNALLING UNIT IN MB ADDRESS
In the defined physical address there is no CCS or
channel-specific signalling unit.
9017
NO VALID COMPUTER IN MB ADDRESS
On the basis of the given physical address, it is not
possible to identify the corresponding computer unit (type,
index).
9018
ACTIVE CM IN RESET
A CM unit in active state is restarted.
9019
LST PCM FOUND, NO LSA CONNECTIONS TO GSW,
SWI
An internal (channel-specific) signalling PCM-circuit has
been found, but no connections to GSW or SWI.
9020
Issue: 30-0
NO GSW OR SWI HARDWARE INFO FROM SWICOP
DN987378
259
Error messages
General Error Messages of System
This error code is generated when the SWICOP in the
marker does not return information on whether the GSW or
SWI is old or new hardware.
9021
PCM SERVED BY TIME SLOT BASED UNIT AND ITS
TIME SLOTS NOT FOUND
A PCM circuit served by a time-slot based unit and its
time-slots are not found: the value parameter is too big or
a record is missing.
9022
UNKNOWN UNIT
The search keys connected with the given computer unit
are not found in the PCM-TSL search key table of timeslot-based units of FUNLIB.
9023
BAD PCMCON FILE SEGMENT
The PCMCON file can not be read due to e.g. a missing
GDT definition.
9024
STAGE TOO LARGE
The value of the stage is too large.
9025
RECORD TO BE CREATED ALREADY EXISTS IN FILE
The record to be created already is in the file.
9026
ATTEMPT TO USE TIMESLOT OF SPECIFIC PCM
CIRCUIT JOINTLY
An attempt has been made to use a certain timeslot of a
certain PCM circuit jointly.
9027
NO FREE RECORDS INITIALIZED WITH FF FOUND
FOR CREATING PURPOSES
No free records initialized with FF are found from the file
for creating purposes.
9028
FILE NOT ADDED INTO DISK FILE UPDATE TABLE
The file is not added into the disk file update table because
it is full.
9029
ILLEGAL PARAMETER FOR DISK FILE UPDATE TABLE
An incorrect parameter when adding file information into
the disk file update table: 1. The file number is not found
from the file number table of SCFPRO. 2. The number of
the first record to be updated is too big. 3. The number of
records to be updated is too big.
9030
260
ILLEGAL SWITCH
DN987378
Issue: 30-0
General Error Messages of System
Error messages
An attempt has been made to give or search for an
undefined switch type or switch (e.g. SSW40).
9031
SWITCH NOT FOUND
An attempt has been made to give or search for a switch
type or switch that has been defined but, however, can not
be found from the file to be read or updated.
9032
SSU PCM CIRCUIT NOT FOUND
The PCM circuit supervised by the INREGI program block
is not found in the subscriber-stage-specific PCMCON file.
9033
ERROR FROM FUNLIB PROGRAM BLOCK
This error message is generated when the error returned
by the FUNLIB program block does not have to be
examined more closely.
9034
NEW AND OLD CLS VARIANTS IN EXCHANGE
The exchange configuration includes both an old (CLS)
and new (CL1TG, CL2TG...) CLS variant.
9035
FUNCTION OF PREPROCESSOR UNIT NOT FOUND
The given preprocessor unit function is not found in the
PIPCMI file.
9036
CLS VARIANT NOT FOUND
A CLS unit is included in the exchange configuration but
cannot be found in the OASFIL or FUDCHA file.
9037
PIU DATA ARRAY OVERFLOW
The number of plug-in units found in the equipment
database is greater than the size of the array reserved by
the application for plug-in unit data.
9038
CARTRIDGE NAME UNKNOWN
The type of the cartridge is not found in HWILIB on the
basis of the cartridge name.
9039
CARTRIDGE IDENTIFICATION UNKNOWN
The name of the cartridge is not found in HWILIB on the
basis of the cartridge identifier (type).
9040
SOFTWARE PACKET IDENTIFICATION NOT FOUND
The identifier of the software packet given is not found in
the equipment database.
9041
Issue: 30-0
NAME OF A PLUG-IN-UNIT FUNCTION NOT FOUND
DN987378
261
Error messages
General Error Messages of System
The plug-in unit function name in ASCII form cannot be
found.
9042
SUBDATABASE REFRESHMENT REQUESTED
A subdatabase refreshment has been requested. This
error code is sent by the SSHPRB program block to the
process requesting the updating of the subdatabase.
SSHPRB has failed twice in its attempts to update the
subdatabase, hence the request for its refreshment.
9043
CHECK SUM NOT CHANGED
The check sum has not changed. The SSHPRB program
block compares the check sum it receives against the
current check sum in the LIETOL file. If the check sum has
changed, SSHPRB returns the (changed) circuit classes to
the subscriber module. Otherwise this error code is
returned.
9044
DUMMY PARAMETER VALUE
This error code is generated when there is an attempt to
read from PRFILE a parameter whose value is in excess of
the maximum default allowed.
9045
PARAMETER ACCESS TABLE NOT OK
This error code is generated when there is an
unsuccessful attempt to read a PRFILE parameter (a
subrecord in PRFILE). The probable reason for this is that
there has been an error in the initialisation of the PRFILE
access table.
9046
PARAMETER NUMBER IS TOO BIG
This error code is generated when there is an attempt to
read from PRFILE a parameter that does not belong to the
class given.
9047
PARAMETER CLASS NOT USED
This error code is generated when the given parameter
class is not in use in PRFILE.
9048
DB OBJECT IS PSAD / PSFP
This error code is generated when
hwi_cart_loc_by_alarm_r finds the given CLAC and alarm
group in a rack and not in a cartridge.
9049
RACK OR CABINET NAME IS UNKNOWN
This error code is generated when
hwi_rack_type_by_name_r receives an unknown ASCII
name.
262
DN987378
Issue: 30-0
General Error Messages of System
9050
Error messages
RACK OR CABINET TYPE IS UNKNOWN
The error code is generated when
hwi_rack_name_by_type_r receives an unknown rack
type.
9051
PLUG-IN UNIT HAS TOO MANY FUNCTIONS
This error code is generated when the plug-in unit being
examined has more facilities than can be held by the
current data structures.
9052
PLUG-IN UNIT HAS NO FUNCTIONS
This error code is generated either when no facilities at all
are found for the plug-in unit(s), or when no new facilities
are found.
9053
MASTER UNIT NOT FOUND
This error code is generated when no master unit or
master unit type can be found from the Equipment
Database.
9054
NO SUBUNITS FOUND
This error code is generated when no subunits are found
for the given master unit (which is included in the
Equipment Database) or master unit type.
9055
DATA CORRESPONDING TO THE GIVEN
PARAMETER(S) NOT FOUND
Data corresponding to the parameter(s) given in a library
call is not found.
9056
DUAL PORT MEMORY IS TOO SMALL
This error code is generated when the size of the dual port
memory is too small.
9057
EQDATA DATABASE SEARCH COMPLETED
This error code will be generated if no more database
objects fulfilling the search criteria could be found from the
EQDATA database.
9058
SUBRACK TYPE IS UNKNOWN
This error code is generated when
hwi_subrack_name_by_typ_a_r routine gets an unknown
subrack type as input parameter.
9059
Issue: 30-0
SUBRACK NAME IS UNKNOWN
DN987378
263
Error messages
General Error Messages of System
This error code is generated when
hwi_subrack_type_by_nam_a_r routine gets an unknown
subrack name as input parameter.
9060
CHANGING OF PARAMETER VALUE DENIED
This error code is generated if it is tried to change a
parameter valuewhen changing is not authorized or
parameter has interdependencies to (optional) parameters
which are not set. The parameter is located in a parameter
file (prfile, fifile, for example).
9061
CHANGING OF ACTIVATION STATUS DENIED
This error code is generated if you have tried to change
the activation status of an optional parameter in the FIFILE
file and the change is not allowed.
9062
SAME ACTIVATION STATUS ALREADY SET
This error code is generated if you have tried to set an
activation status which is already set on an optional
parameter in the FIFILE file, for example.
9063
INTERDEPENDENCE TO A NOT CHANGEABLE
PARAMETER
This error code is generated if you have tried to read or
change value of a parameter which has interdependence
to another (optional) parameter being not set.
9064
OPTIONALITY PARAMETER IS ACTIVE
This error code is generated when a parameter is defined
to be optional locating in the FIFILE file but the
corresponding parameter position in the PRFILE does not
have the correct value indicating this.
9065
LOCAL UNIT UPDATE FAILURE
This error code is generated if update of the local, active
(WO) unit has failed.
9066
PRFILE READ ERROR
This error code is generated if reading of the General
Parameter File PRFILE fails.
9067
FIFILE FILE READ ERROR
This error code is generated if reading of the Feature
Information Control File FIFILE fails.
9068
FIFILE FILE DOES NOT EXIST
This error code is generated when trying to access
nonexistent FIFILE file.
264
DN987378
Issue: 30-0
General Error Messages of System
9069
Error messages
PARAMETER DATA COLLECTION ERROR
This error code is generated if data of the parameters
cannot be collected.
9070
ALL PARAMETERS OF A CLASS ARE SECRET
This error code is generated when trying to read all
parameters of a class and they are secret.
9071
NO DATA OF AN OPTIONALITY PARAMETER
This error code is generated when trying to read or change
the value of an optional parameter which cannot be found.
9072
ILLEGAL REFERENCE FIELD IN THE MESSAGE
This error code is generated when the reference field of a
parameter update message does not contain the sum of
the parameter class and the parameter number fields.
9073
PARAMETER CLASS DOES NOT EXIST
This error code is generated when the given parameter
class cannot be found from the parameter files
(fifile,prfile,prbfil,...).
9074
PARAMETER NUMBER DOES NOT EXIST
This error code is generated when the given parameter
number cannot be found from the given parameter class in
the parameter file (fifile,prfile,prbfil,...).
9075
SAME PARAMETER VALUE ALREADY SET
This error code will be generated if there is an attempt to
update the same value to a parameter it already has.
9076
INTERDEPENDENCE PARAMETER NOT FOUND
This error code is generated if the interdependence
parameter having legal class and number ID cannot be
found from the parameter files (PRFILE, FIFILE, PRBFIL).
9077
PARAMETER NOT FOUND FROM PARAMETER FILES
This error code is generated when the given input
parameter has not been found from the parameter files
(PRFILE, FIFILE, PRBFIL). The parameter does not mean
in this context an interdependence parameter.
9078
INTERDEPENDENCE TO CHANGEABLE PARAMETER
This error code is generated when PRFILE parameter has
interdependence to a changeable parameter whose value
is FALSE.
Issue: 30-0
DN987378
265
Error messages
General Error Messages of System
9079
PARAMETER VALUE IS TOO BIG
This error code is generated if such a value is tried to be
updated that exceeds the maximum allowed value.
9080
UPDATE PREVENTED BY UNIT STATE
ADMINISTRATION
This error code will be generated when unit state
administration does not allow memory file nor disk file
updatings.
9081
TRIAL CONFIGURATION ALREADY CREATED
This error code will be generated when operator tries to
create trial configuration but it has already been done.
9082
CUTOVER ALREADY PERFORMED IN TRIAL
This error code will be generated when operator tries to
perform cutover operation to trial part of the network
element but it has already been done.
9083
CUTOVER NOT PERFORMED IN TRIAL
This error code will be generated when operator tries to
perform cutover operation to original part of the network
element but cutover has not been performed to trial part
earlier.
9084
DELETING TRIAL CONFIGURATION NOT POSSIBLE
This error code will be generated when operator tries to
delete trial configuration but either of the following
conditions is fulfilled: - when canceling trial configuration
cutover has been performed to trial part of the network
element - when completing trial configuration cutover has
not been performed to trial part of the network element
9085
UPDATING SOMAFI FILE FAILED IN TRIAL
This error code will be generated when updating request or
direct update of the SOMAFI file has terminated to an error
during a trial operation.
9086
DISCREPANCY BETWEEN TRIAL SYM UNITS
This error code will be generated when active HMS master
node has to be changed to another sym unit but there
exists discrepancy of the correct location unit of the node
between program blocks involved in the changed
procedure.
9087
266
TERMINATE MML SESSION IN TRIAL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
This error code will be generated if recovery announces as
a response to a trial operation request that MML session
should be terminated. This kind of situation arises, for
example, when restart of a SYM unit is activated in that
part of a divided network element where sender of the
mentioned trial request is located.
9088
HMS ACTIVE MASTER NODE IN FAULTED SYM UNIT
This error code will be generated whenever HMS active
master node is located in faulted System Maintenance
Unit. It is possible that some attempts have been made to
move the node into a non-faulted SYM unit but they have
failed. These error situations are associated with TRIAL
operations.
9089
PARAMETER IS NOT FOUND IN PRBFIL
This error code is generated if parameter information is
requested but there is no information of parameter in
PRBFIL files. The requested parameter is located in a
parameter file (prfile, fifile, for example).
9090
IP ADDRESS VERSION IS UNDEFINED
This error code is generated when SWUPDA hand process
receives interface data with undefined IP address version
from JANINA process family after trial cutover operation
has been successfully performed.
9091
INCORRECT BIT MASK COMBINATION
This error code is invoked whenever a PHFLIB updating
service is called with an incorrect bit mask combination
parameter. The extent of the update to be performed by
the service is unclear.
9092
USE OF TIME SLOT 16 IS DISABLED
This error code will be generated if client wants to set tsl
16 in use but according to file information use of tsl 16 is
disabled. In other words, there is a conflict between the
client and file information, concerning use of tsl 16.
9093
PARENT UNIT INDEX NOT FOUND
This error code is generated whenever either a specified
(user-given) or unspecified (uninitialised) parent unit index
is not found in the configuration data. The unspecified
index in this context is the value of
unit_index_t_any_index_c.
9094
Issue: 30-0
IMA GROUP NOT CREATED
DN987378
267
Error messages
General Error Messages of System
This error code will be generated whenever an attempt is
made to modify or delete an IMA group which does not
exist. This decision is made according to group_created
status info in the IMPARA file.
9095
SET UNITS UNSPECIFIED IN PROTECTION GROUP
This error code is set if none of the section SET unit
indexes has been defined as the protection group location
info. This kind of situation can arise, for example, when
updating the state of a phyTTP that is on top of a
protection group.
9096
NO ROOM FOR A NEW SET IN THE PROT. GROUP
This error code is generated whenever a new SET network
interface unit cannot be added to a protection group
because the group already contains both SETs. Indexes of
the SETs are different from the new one.
10001
PAYPHONE NOT IN SUPERVISION
The payphone is not included in the supervision.
10002
SPECIAL ROUTE IN OTHER USE
The special route in question is used by another facility
than an announcement.
10003
ANNOUNCEMENT EXISTS
The special route in question is already an announcement
record.
10004
ANNOUNCEMENT PARAMETERS EXIST
Announcement parameters with the same name already
exist.
10005
ANNOUNCEMENT PARAMETERS NONEXISTENT
Announcement parameters with that name do not exist in
the ANNPAR file.
10006
INVALID PARAMETER NAME
The parameter with the given name does not exist.
10007
INVALID SIGNALLING
The outgoing register signalling name was incorrect.
10008
SPECIAL ROUTE DEFINED IN ROUTE GROUP
The special route in question is used in routing (defined in
the CMORGR file).
268
DN987378
Issue: 30-0
General Error Messages of System
10009
Error messages
NO SPACE FOR ANNOUNCEMENT PARAMETERS
The ANNPAR file is full, there is no space to define new
announcement parameters.
10010
NO FREE HANDS AVAILABLE
There are no free hands to execute the task.
10011
CRC MEASUREMENT IS NOT POSSIBLE IN THIS ET
UNIT
The CRC errors can not be measured in the ET due to its
functional mode.
10012
MODULE FILE INCONSISTENCY (MODULE, MDROUT
AND SBDIND FILES)
The module files (MODULE, MRDOUT and SBDIND) are
inconsistent. The error can appear only in the
acknowledgement message module_inq_s. The fault
situation arises when one of the files is in different state
than the others. E.g. one file contains the basic value and
the others data. The user must find out which file or files
are incorrect.
10013
ET STATE NOT SE-NH
The state of the ET is not SE-NH, which means that it can
not be removed.
10014
CIRCUIT NOT FREE
The circuit is already connected through the switch.
10015
DISCONNECTION UNSUCCEEDED
Disconnection failed in the switch.
10016
INCORRECT BANDWIDTH
The bandwidth value in the message sent by the MML
program to the CM was incorrect. The bandwidth was 0, or
it was bigger than 30 in PCM with signalling or bigger than
31 in PCM without signalling.
10017
INCORRECT DIRECTION
The direction value in the message sent by the MML
program to the CM was incorrect.
10018
CANNOT REMOVE LAST OUTGOING CIRCUIT
Only one outgoing branch is left. The user tried to remove
it.
10019
Issue: 30-0
LAST MEMBER OF GROUP CALL
DN987378
269
Error messages
General Error Messages of System
The subscriber to be removed from the hunting group is
the last member of the group. In this case the removal is
not possible.
10020
INCORRECT MEMBER COUNT
An attempt has been made to add too many members into
a hunting group.
10021
MEMBER ALREADY IN USE
An attempt has been made to add into the hunting group a
member that already is a member of another group (in
connection with analogue groups).
10022
ALREADY EXTENSION
The subscriber to be added into a hunting group already is
a member of another group. However, the subscriber can
be added into an ISDN group, since in ISDN groups the
same subscriber can be a member of several groups.
10023
NO SUCH HUNTING GROUP
The hunting group given in the command does not belong
to the group call number in question.
10024
NO SUCH EXTENSION
The extension given in the command does not belong to
the hunting group.
10025
NO HUNTING GROUPS
No hunting groups are connected to the subscriber line
given in the command, in other words, it is not a group call
number.
10026
TOO MANY EXTENSIONS
An attempt has been made to add too many members into
the hunting group. The maximum number is 8 per hunting
group.
10027
INCORRECT DMA ACCESS
The DMA plug-in unit does not function. The DMA circuit is
faulty. Change the plug-in unit.
10028
DISK DIRECTORY NOT EMPTY
An attempt has been made to destroy a disk directory that
contains files.
10029
270
DISK DIRECTORY FULL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The disk directory is full of files, and the creation of new
ones does not succeed anymore.
10030
NO SUCH DIRECTORY ON DISK
An attempt has been made to direct a file operation to a
non-existent disk directory.
10031
ERROR IN DISK MEDIUM
The surface of the disk is faulty. Change the disk drive.
10032
FAILURE IN DISK HARDWARE
The disk drive is faulty. Change the disk drive.
10033
DISK COMMAND ABORTED
The execution of a disk command is interrupted.
10034
SCSI CONTROLLER BUSY
The SCSI bus controller of the disk is reserved to the use
of another computer unit.
10035
DISK RESERVATION CONFLICT
An attempt has been made to reserve the disk from
several computer units at the same time.
10036
TOO DEEP DIRECTORY PATH
A too long directory path of a disk file has been defined.
10037
ILLEGAL COMMAND TO THIS DISK FORMAT
The given command can not be executed on the disk
format on the disk.
10038
ILLEGAL COMMAND TO THIS DEVICE
The hardware does not support the given task.
10039
FAILURE IN SERO LOOP TEST
The loop test of the SERO plug-in unit has failed. Change
the SERO plug-in unit.
10040
SERO TRANSMITTER EMPTY
The transmission buffer of the SERO plug-in unit has been
emptied, even though the character transmission is not
allowed. Change the SERO plug-in unit.
10041
FIFO FAILURE IN SERO BOARD
The FIFO buffer of the SERO plug-in unit is faulty. Change
the SERO plug-in unit.
Issue: 30-0
DN987378
271
Error messages
General Error Messages of System
10042
FIFO CANNOT TRANSMIT DATA ON SERO BOARD
The FIFO on the SERO plug-in unit can not transmit data.
Change the SERO plug-in unit.
10043
SERO INCOMING DATA INTERRUPT ERROR
The interruption of incoming data of the SERO plug-in unit
does not function. Check the interruption wiring. Change
the SERO plug-in unit.
10044
CNTRL-B GIVEN FROM VDU
A notice of the VDUDRI program block to the DIALOG
program block, of a CNTRL-B character received from a
MML terminal.
10045
CHANGE LANGUAGE IN MML TEXT
A notice of the VDURDI program block to the DIALOG
program block, of changing the language of MML texts.
10046
BREAK GIVEN
A notice of the VDUDRI program block to the DIALOG
program block, of the BREAK character received from the
MML terminal.
10047
CNTRL-Y GIVEN FROM VDU
A notice of the VDUDRI program block to the DIALOG
program block, of a CNTRL-Y character received from the
MML terminal.
10048
CNTRL-X GIVEN FROM VDU
A notice of the VDUDRI program block to the DIALOG
program block, of a CNTRL-X character received from the
MML terminal.
10049
SET MML PROGRAM IN TEST MODE
A notice of the VDUDRI program block to the DIALOG
program block, of starting the test output of an MML
program.
10050
SERO OUTGOING DATA INTERRUPT ERROR
The interrupt of outgoing data of the SERO plug-in unit
does not function. Check the interrupt wiring of the SERO
plug-in unit. Change the SERO plug-in unit.
10051
SERO TERMINAL NOT READY
The transmission and receiving circuits of the SERO plugin unit are not functioning. Change the SERO plug-in unit.
272
DN987378
Issue: 30-0
General Error Messages of System
10052
Error messages
SERO BOARD CHARACTER INPUT ERROR
The character receiving logic of the SERP plug-in unit
does not function. Change the SERO plug-in unit.
10053
SERO BOARD CHARACTER INPUT TIME-OUT
The character reading of the SERO plug-in unit has ended
due to time-out. Change the SERO plug-in unit.
10054
TIME OUT IN PRINTING MML COMMANDS
The output of MML commands on the printer has failed
due to time-out.
10055
ILLEGAL SEGMENT
An attempt has been made to refer to a non-existent
segment.
10056
NO SUCH TAPE FILE
The file is not found on the tape.
10057
I/O TASK COMPLETED PARTLY OK
The IOMANA program block has directed a task to several
I/O devices at the same time, and all the I/O devices have
not succeeded in performing the task.
10058
ANNOUNCEMENT PARAMETERS DEFINED IN SPECIAL
ROUTE
The announcement parameters are used in
announcement(s) (defined in the SPCROU file).
10059
CENTREX CALL NUMBER
The subscriber number is a call number of a CENTREX
group.
10060
OUTPUT ERROR TEXT
A notice of the VDUDRI program block to the DIALOG
program block, of the user having pressed the CNTRL-7
character. This causes that DIALOG outputs the broader
explanation of the MML program error code last displayed
on the MML terminal.
10061
RESERVED CENTREX EXTENSION NUMBER
The subscriber number is reserved as an extension
number of a CENTREX group.
10062
Issue: 30-0
USART ERROR ON SERO BOARD
DN987378
273
Error messages
General Error Messages of System
The USART circuit of the SERO plug-in unit has detected a
failure in the terminal or printer interface. Check that the
terminal or printer is connected and that the power is on.
Change the terminal or printer. Change the SERO plug-in
unit.
10063
INCORRECT FILE LIST STRUCTURE - FILE LOADING
NOT POSSIBLE
The structure of the file list (FLLIST) is incorrect.
10064
MEMBER OF CENTREX GROUP
The subscriber is a member of a CENTREX group.
10065
UNKNOWN SUBSCRIBER
The given subscriber does not exist in database.
10066
UNKNOWN BASIC SERVICE
The given basic service does not exist in database.
10067
SUBSCRIBER ALREADY EXISTS
The operator wants to create a subscriber, that already is
created in database.
10068
BUFFERED REPORT NOT FOUND
The required report is not found in the ring buffer.
10069
INTERNAL PRINTING QUEUE OF REBMAN IS FULL
The table into which REBMAN stores the reports to be
printed out is full.
10070
BUFFERED REPORT IS QUEUING IN INTERNAL
PRINTING QUEUE OF REBMAN
The report output does not start immediately, instead is
was placed in the internal printing queue of REBMAN.
10071
SYSTEM DOES NOT CONTAIN SUCH DATABASE
With the commands of the DBHAND MML program, the
user has given such a database name that does not exist
in the system.
10072
DATABASE DOES NOT CONTAIN SUCH FILE
The database under examination does not contain a
database file with the file number in question.
10073
DATABASE DOES NOT CONTAIN SUCH TRANSACTION
The given data base does not contain a transaction or
fastread with the given number.
274
DN987378
Issue: 30-0
General Error Messages of System
10074
Error messages
DATABASE LOG BUFFER DOES NOT CONTAIN MORE
UPDATES
From the log buffer of a database, the special hand
scatterer has already found all updates.
10075
TRANSACTION HAND OF DATABASE HAS NOT
COMMITTED TO TRANSACTION
In the database system, the transaction hand which has
been chosen to execute a given transaction has not yet
committed to the transaction.
10076
TRANSACTION HAS BEEN ABORTED
In the database system, the transaction execution has
failed and the transaction has been aborted.
10077
TRANSACTION OR FASTREAD EXECUTION HAS
LASTED TOO LONG
Time-out has occurred in the transaction or fastread
execution; transaction has been aborted.
10078
IN DATABASE SYSTEM RESOURCES HAVE BEEN
EXHAUSTED
In the database system, too many buffers or hands etc.
have been needed. The transaction has been aborted.
10079
FATAL ERROR HAS OCCURRED IN DATABASE
SYSTEM
A fatal error has occurred to the database managers or
database hands. The execution will be stopped.
10080
TRANSACTION OR FASTREAD ERROR HAS
OCCURRED
An error has occurred to the fastread or transaction hand
of a database system. The transaction has been aborted.
10081
TRANSACTION HAND HAS ASKED LOG BUFFER AREA
IN WRONG TRANSACTION PHASE
The log buffer area is asked for by a transaction hand in
the active unit, the corresponding hand of which is not in
the same transaction phase in the spare unit.
10082
DATABASE LOG BUFFER ERROR
In the database system, an error has occurred when
handling log buffer.
10083
Issue: 30-0
ERRONEOUS TRANSACTION OR FASTREAD
PARAMETERS
DN987378
275
Error messages
General Error Messages of System
In a transaction or fastread message, the parameters are
not correct.
10084
DATABASE FILE CLASS IS NOT CORRECT
With the commands of the DBHAND MML program, the
user has given an incorrect file class.
10085
DATABASE SYSTEM HAS NOT ANSWERED TO
TRANSACTION OR FASTREAD REQUEST
The transaction or fastread execution has been requested
from a database system but no response has come in
time.
10086
BUFFERED REPORT IDENTIFIER IS AMBIGUOUS
Several reports are found with the given identifier, in other
words, it is impossible to pick only one report.
10087
DATABASE SYSTEM IS NOT IN NORMAL STATE
The database system is loading, dumping etc. so that it
cannot execute the required task.
10088
DUMP FAILED ON ONE DISK, BUT WAS SUCCESSFUL
ON ANOTHER
The dumping has failed on one disk. The database is
consistent.
10089
DATABASE DUMP FAILED. OLD VERSION OF
DATABASE ON DISK WILL BE USED
The dumping has failed on both disks. The database on
disks is inconsistent. Dump again immediately.
10090
WO AND SP UNITS NOT SYNCHRONIZED IN
DATABASE SYSTEM
The SP master of the database system has failed to
synchronize itself with the WO master. This leads to a fatal
error in the spare unit.
10091
DATABASE REQUEST SENT TO WRONG RECEIVER
In the database system, an administrative message has
erroneously been sent to the spare unit.
10092
DATABASE HAS NO DISK COPY
The database in question is only a RAM database. Disks
copies do not exist.
10093
DATABASE SYSTEM TIME-OUT ERROR
A time-out has occurred in the database system.
276
DN987378
Issue: 30-0
General Error Messages of System
10094
Error messages
DATABASE LOADING IN PROGRESS
The database manager is loading database files.
Transactions cannot be executed.
10095
SPARE UNIT UPDATE FAILURE
The file update in the spare unit has failed.
10096
DISK READ ERROR
Reading from the disk has failed.
10097
COMMUNICATION FAILURE DURING DATA TRANSFER
An error during the MOVIES data transfer service.
10098
DMA ERROR
Reading from the disk has failed because of a DMA error.
10099
DISK ERROR
Disk drive initialization has failed.
10100
LOAD MODULE IS TOO BIG
The load module is too big, there is no room in the
memory.
10101
INCORRECT LOAD MODULE LENGTH
The length data in the load module is bigger than in the
disk directory.
10102
NO DISK DATA
The disk data file is not found from the disk.
10103
DIRECTORY NOT FOUND
The directory is not found from the disk.
10104
PACKET DIRECTORY NOT FOUND
The correct packet directory is not found from the disk.
10105
SUBDIRECTORY NOT FOUND
The BLCODE or LFILES subdirectory is not found from the
packet directory.
10106
PACKET IDENTIFIER INVALID
The packet identifier in the RAM is invalid.
10107
CHAIN ERROR
The load module chain in the RAM is invalid.
Issue: 30-0
DN987378
277
Error messages
General Error Messages of System
10108
WRONG MODULE
The load module in the RAM and the load list contain
different load module names.
10109
MODULE CHECKSUM ERROR
The check sum of the load module is incorrect.
10110
ILLEGAL MESSAGE
An incorrect message has been received from the
BOMBER program block.
10111
BREAK STATE
The normal message exchange has been interrupted e.g.
because the BOMBER program block has not found the
required load module.
10112
MESSAGE TIME-OUT
The time limit of message exchange has expired.
10113
NO START BIT
In the MB message to be received, the bit indicating its
start is not correct.
10114
MESSAGE LENGTH ERROR (2)
The length of the MB message to be received is incorrect.
10115
TARGET AREA TOO SMALL FOR AIMED DATA
The size of the target area is too small for the aimed data
to be written into it.
10116
NO SUCH FILE ON DISK
The required file is not found from the disk.
10117
ERRONEOUS PARAMETER IN MOVIES FUNCTION
CALL
There is something wrong in the parameters of MOVIES
function call.
10118
NOT READY
BOTTOM is asked for in a unit other than the OMU, but
BOMBER has not yet received a start message from
USAPRO.
10119
NO PERMISSION
The unit asking for load module has no load permission.
278
DN987378
Issue: 30-0
General Error Messages of System
10120
Error messages
LOAD MODULE NOT FOUND
The required module is not found from the chain.
10121
NO MODULE
The unit asking for more data has no module to be loaded.
10122
NO USABLE DISK
Neither of the winchester disks is in state WO-BU.
10123
SWTEST STATUS NOT AVAILABLE
The test status can not be read.
10124
DIFFERENT SWTEST STATUS
The units have a different test status.
10125
DIFFERENT PACKAGE
The units have a different package identifier.
10126
SOWADM BREAK
An error status is received from SOWADM when inquiring
the package identifier and/or directory of the package.
10127
EDISKD TIME-OUT
No reply received from the EDISKD program block.
10128
PCM HAS SIGNALLING, T16 IS ILLEGAL
TSL 16 is in signalling use. It may not be given as the first
TSL.
10129
USER ALREADY EXISTS
The user identification already exists.
10130
USER DOES NOT EXIST
The user identifier does not exist.
10131
APPLICATION FIELD DOES NOT EXIST
The application field does not exists.
10132
NETWORK ELEMENT DOES NOT EXIST
The network element does not exist.
10133
NO PRIVILEGE FOR NETWORK ELEMENT
The user has no authorities to the target network element.
10134
Issue: 30-0
NO PRIVILEGE FOR APPLICATION FIELD
DN987378
279
Error messages
General Error Messages of System
The user has no authorities to the target application field.
10135
NOT LOCAL PAYPHONE LINE TYPE
The line is not a local payphone line according to the
central memory (CM). The operation failed.
10136
FIRST HUNTING GROUP OF GROUPCALL NUMBER
WITH POSITION NUMBER
The first hunting group of a group call number with a
position number can not be removed if there are other
hunting groups in the group call number.
10137
HUNTING GROUP ALREADY CREATED
When creating a group call number, the first hunting group
is created at the same time (HGR=0) after which only new
members can be added into this hunting group.
10138
SUBSCRIBER IS NOT MEMBER OF CENTREX
Only such centrex subscribers that are members of the
same centrex hunting group as well can belong to a
centrex group call number.
10139
SHORT CIRCUIT TEST IS NOT NEEDED
The short circuit test is not needed. The operation
succeeded.
10140
ACTIVE UNIT STATE INCORRECT
The active unit is in some other state than WO-EX.
10141
PASSIVE UNIT STATE INCORRECT
The passive unit is in some other state than SP-EX or SPUP.
10142
APPLICATION ALREADY EXISTS
The application already exists.
10143
SEMIPERMANENT FILE UPDATING BUSY
The semipermanent file is being updated.
10144
SWITCHOVER PREPARING
The switchover is being prepared.
10145
DESTINATION BELONGS TO TIME CONTROLLED
ROUTING
The destination belongs to time controlled routing and
cannot be removed.
280
DN987378
Issue: 30-0
General Error Messages of System
10146
Error messages
APPLICATION DOES NOT EXIST
The application does not exist.
10147
INCORRECT MESSAGE RECEIVED FROM MML
PROGRAM
The message sent by an MML program is incorrect.
10148
NONEXISTENT TIME CONTROL
The given time control does not exist in time-controlled
routing.
10149
SWITCHOVER
The switchover is in progress.
10150
CONFLICT BETWEEN ACTIVE AND PASSIVE UNIT
OAPFIL FILE
The OAPFIL files of the active and passive units contain
contradictory information.
10151
COMMUNICATION ERROR BETWEEN PASSIVE UNIT
O7MANA AND ODBUPD
Communication between the passive unit O7MANA and
ODBUPD program blocks has failed.
10152
COMMUNICATION ERROR BETWEEN ACTIVE UNIT
O7MANA AND ODBUPD
Exchange of messages between program blocks O7MANA
and ODBUPD in the active unit failed.
10153
COMMUNICATION ERROR AND ONLY PASSIVE UNIT
FILES UPDATED
Communication between active unit O7MANA and
ODBUPD program blocks has failed. Only passive unit
files are updated.
10154
COMMUNICATION ERROR BETWEEN ACTIVE AND
PASSIVE UNIT O7MANA
The operation succeeded completely.
10155
FILE UPDATED ONLY IN PASSIVE UNIT
The files are updated only in the passive unit.
10156
FILE UPDATED ONLY IN ACTIVE UNIT
The files are updated only in the active unit.
10157
Issue: 30-0
PACKAGE NOT FOUND
DN987378
281
Error messages
General Error Messages of System
The package is not found in the SOMAFI file.
10158
PACKAGE NOT ACTIVE
All the items listed in the MAFILE file, belonging to the
package, are not default versions on the disk.
10159
NO FREE PACKAGE RECORDS IN SOMAFI
There are no free records in the SOMAFI file.
10160
PACKAGE IS RUNNING
The package is running in some unit.
10161
DISK READ FAILURE
The disk file can not be read.
10162
FILE ERROR IN SOMAFI
There is a file error in the SOMAFI file.
10163
FILE ERROR IN UNPACK
There is a file error in the UNPACK file.
10164
SOMAFI NOT USABLE
The SOMAFI file can not be read from the disk, or it can
not be created as a file.
10165
UNPACK NOT USABLE
The UNPACK file can not be read from the disk, or it can
not be created as a file.
10166
SOMAFI UPDATE ON DISK FAILED
The update of SOMAFI does not succeed on either disk.
10167
SOMAFI UPDATE NOT SUCCEEDED ON BOTH DISKS
The update of SOMAFI file succeeded only on the other
disk.
10168
SUBSCRIBER IS NOT ANALOG GROUP CALL NUMBER
The subscriber number is not an analog group call number.
10169
SUBSCRIBER IS NOT ISDN GROUP CALL NUMBER
The subscriber number is not an ISDN group call number.
10170
SUBSCRIBER NOT CALL NUMBER OF CENTREX
GROUP
The subscriber number is not a CENTREX group call
number.
282
DN987378
Issue: 30-0
General Error Messages of System
10171
Error messages
FILE SYSTEM RECOVERY ERROR
The recovery of the file system has failed.
10172
OAPFIL FILE READING FAILED
The reading of a record in the OAPFIL file has failed.
10173
PLUG-IN UNIT CODE RAM WRITE ERROR
Writing in the program memory (RAM memory) of the plugin unit does not succeed when loading program package
into the plug-in unit. The reason for the failure may a faulty
plug-in unit, an incorrect bridge connection on the plug-in
unit, a failure on the DMC bus, incorrect information on the
plug-in unit in the MUFILE file or an incorrect program
package (an error in the PISOFT file).
10174
LOADED PLUG-IN UNIT SOFTWARE PACKET CHECK
ERROR
When checking the success of program package loading, it
has been detected that the check sums counted from the
plug-in unit and from the code file are different. The reason
for the error may a fault in the memory of the 80386
processor, a faulty plug-in unit, an incorrect bridge
connection on the plug-in unit, incorrect information on the
plug-in unit in the MUFILE file or an incorrect program
package (an error in the PISOFT file).
10175
OSI ADDRESS CONNECTED TO APPLICATION TO BE
DELETED
One or more OSI addresses have been connected to the
application to be deleted.
10176
SIZE OF PLUG-IN UNIT SOFTWARE PACKET IS TOO
BIG
When loading the program package of the plug-in unit, it
has been detected that the size of the dual port memory is
smaller than the size of the program package to be loaded.
The reason for the error may be an incorrect program
package of the plug-in unit, an error in the PISOFT file or
incorrect information on the plug-in unit in the MUFILE file.
10177
COMMAND GROUP NOT FOUND
The command group is not found in the MCOMND file.
10178
TAUTHO FILE EMPTY
The TAUTHO file is empty.
10179
AUTHORITIES NOT CHANGED
It has not been possible to change the authorities.
Issue: 30-0
DN987378
283
Error messages
General Error Messages of System
10180
OLD PASSWORD VERIFICATION ERROR
An error has occurred in the verification of an old
password.
10181
NEW PASSWORD VERIFICATION ERROR
An error has occurred in the verification of a new
password.
10182
MINIMUM PASSWORD LENGTH IS 6
The defined password is too short. The length of a
password is at least six characters.
10183
MAXIMUM PASSWORD LENGTH EXCEEDED
The defined password is too long.
10184
USER ID NOT CREATED
It has not been possible to create the user identification.
10185
USER ID NOT DELETED
It has not been possible to delete the user identification.
10186
OWN USER ID
The user has given his own user identification.
10187
PLUG-IN UNIT DESCRIPTOR BUILD ERROR
The creation of a descriptor pointing to the dual port
memory of a plug-in unit has failed. The reason for the
failure may be incorrect information on the plug-in unit in
the MUFILE file, packaging error of the program block
creating the descriptor, or an error in the operating system.
10188
TIME LIMIT EXPIRED WHEN LOADING SOFTWARE OF
PLUG-IN UNITS
The total time limit of loading plug-in unit software package
has expired.
10189
AET ALREADY RESERVED
The AET is already used by an application.
10190
ADDRESS INFO OF PLUG-IN UNIT ILLEGAL IN MUFILE
The address information on the plug-in unit in the MUFILE
file are incorrect or incompatible with the plug-in unit type.
10191
284
MML PROGRAM INITIALIZATION FAILED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The initialization of a MML program has failed. The reason
for the error may be e.g. the failure of message exchange
with the partner program block.
10192
OFFSET OUT OF SUBRECORD
The offset is greater than or of the same size as the size of
a subrecord in the file.
10193
OADFIL FILE READING FAILED
The reading of a record in the OADFIL file has failed.
10194
CONFLICT BETWEEN OAPFIL AND OADFIL FILES
The OAPFIL and OADFIL files contain contradictory
information.
10195
GIVEN AET IDENTIFIES REMOTE APPLICATION
The AET given in the command identifies a remote
application. Only the AET has been defined for the remote
application.
10196
OSI ADDRESS DOES NOT EXIST
The OSI address does not exist.
10197
OSI ADDRESS IS NOT CONNECTED TO APPLICATION
The OSI address has not been connected to a application.
10198
SEMANTIC CHECK FAILED
The message exchange connected to the semantics check
has failed with the partner program block.
10200
REMOVAL OF ONLY ACTIVE VERSION NOT ALLOWED
The command to remove a disk file or to change its name
has been directed only to the default version of the file,
even though other versions of the file exist. This is
forbidden since one of the file versions must be a default
version.
10201
OBJECT ALREADY EXISTS IN DATABASE
The key value or object number value already has an
object in the database. This value identifies the object, and
it is not possible to create another object with the same
value.
10203
OBJECT DOES NOT EXIST
The object does not exist.
10205
Issue: 30-0
OCGFIL FILE READING FAILED
DN987378
285
Error messages
General Error Messages of System
The reading of a record in the OCGFIL file has failed.
10206
CONFLICT BETWEEN OCGFIL AND OADFIL FILES
The OCGFIL and OADFIL files contain contradictory
information.
10207
FILE DISTRIBUTION AND DISK UPDATE FAILURE
An error has occurred both in file distribution and in disk
update.
10208
WORKFILE UPDATING ON
The updating of a work file is in progress.
10210
FILE ACCESS ERROR
The file operation has failed (e.g. opening, reading or
writing of the file).
10211
INCORRECT NSAP
The combined length of IDI and DSP fields is too great.
10212
PHYSICAL CHANNEL GROUP DOES NOT EXIST
The physical channel group does not exist.
10213
OSI ADDRESS NOT IN LOCKED STATE
The OSI address is not in the LOCKED state.
10214
SEMIPERMANENT FILE UPDATING FAILED
The updating of information in a semipermanent file has
failed.
10215
COMMUNICATION ERROR BETWEEN ACTIVE MARKER
AND ACTIVE CM
The central memory has sent an update request to the
marker, but the marker has not answered within the time
limit (12 s). The update of the marker has failed.
10216
COMMUNICATION ERROR BETWEEN ACTIVE SSU
AND ACTIVE CM
The central memory has sent an update request to the
SSU, but the SSU has not answered within the time limit
(12 s). The update of the SSU has failed.
10217
286
COMMUNICATION ERROR BETWEEN SPARE CM AND
ACTIVE CM
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The active central memory has sent an update request to
the spare central memory, but the spare central memory
has not answered within the time limit (12 s). The update
of the spare central memory has failed.
10218
NO PERMANENT MEASUREMENT REPORT AVAILABLE
TO ET UNIT
The measurement results of the ET unit in question have
not been received from the AFS-S plug-in unit.
10219
TEXTPR IN ABNORMAL STATE
TEXTPR is not in a normal operating state and can not
perform text formatting tasks. TEXTPR is in an abnormal
operating state when it can not open TEFORM and/or
TEOUTP files.
10220
DUPLICATE TEXT FORMING JOB
The same program block has sent a new formatting task
while the previous one is still uncompleted.
10221
UNKNOWN TEXT FORMING JOB
The text forming job is unknown to TEXTPR.
10222
NO PHYSICAL CHANNEL GROUPS EXIST
The physical channel groups do not exist.
10223
SERVICE EXISTS
Supplementary service already exists.
10224
PRIMARY RATE ACCESS NAME EXISTENT
Primary rate access name already exists.
10225
PRIMARY RATE ACCESS NAME NONEXISTENT
Primary rate access name does not exist.
10226
TIME SUPERVISION GROUP NONEXISTENT
The time supervision group does not exist.
10227
MEASUREMENT REPORT OF ET UNIT NOT PRINTED
The TEXTPR program block has answered with a negative
status to the printing request of the ET unit measurement
report.
10228
GIVEN OSI ADDRESS NUMBER IDENTIFIES LOCAL
OSI ADDRESS
The OSI address number given in the command identifies
a local OSI address.
Issue: 30-0
DN987378
287
Error messages
General Error Messages of System
10229
GIVEN OSI ADDRESS NUMBER IDENTIFIES REMOTE
OSI ADDRESS
The OSI address number given in the command identifies
a remote OSI address.
10230
FILE CONFLICT ERROR
It has been detected that the files in two different computer
units contain contradictory information. See alarm 2065
FILE CONFLICT ERROR.
10231
MAXIMUM NUMBER OF ADDRESSES CONNECTED TO
APPLICATION
The maximum number of OSI addresses have already
been connected to the OSI application.
10232
INVALID LOAD MODULE LENGTH
The length of the load module can not be divided by four.
10233
GIVEN AET IDENTIFIES LOCAL APPLICATION
The AET given in the command identifies a local
application.
10234
NONEXISTENT ALARM
The alarm in question is undefined in the alarm system.
10235
NOT CANCELLABLE ALARM
The alarm in question can not be cancelled by the
operator.
10236
ALARM BLOCKING IN QUESTION IS ALREADY SET
The same or corresponding alarm blocking is already set.
10237
ALARM BLOCKING IN QUESTION IS NOT SET
The alarm blocking in question is not set.
10238
RELATIONSHIP DOES NOT EXIST
The relationship does not exist.
10239
RELATIONSHIP ALREADY EXISTS
The relationship already exists.
10240
PRINTING ALREADY BLOCKED
Printing of alarms belonging to the alarm urgency class in
question is already prevented.
10241
288
PRINTING NOT BLOCKED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Printing of alarms belonging to the alarm urgency class in
question is not prevented.
10242
PHYSICAL CHANNEL DOES NOT EXIST
The physical channel does not exist.
10243
SOWADM NOT READY
SOWADM has not yet received a starting message from
USAPRO.
10244
DATA NOT UPDATED
The identifier of the package in the unit has not been
updated in the UNPACK file.
10245
NO ACTION
The task has not been performed.
10246
NO SUCH VERSION
The version can not be found.
10247
DELETING FAILED
The deletion of a disk file has failed.
10248
LOAD MODULE LENGTH ERROR
The load module is too short.
10249
MAFILE NOT OK
The MAFILE file is not in order on either disks.
10250
CHANGE OF ACTIVE VERSION FAILED
The changing of the default version of a disk file has failed.
10251
PHYSICAL CHANNEL GROUP ALREADY EXISTS
The physical channel group already exists.
10252
VIRTUAL CIRCUIT NUMBER USED BY GIVEN
PHYSICAL CHANNEL NUMBER
The virtual circuit number is already used on the given
physical channel in the given channel group.
10253
PHYSICAL CHANNEL IS NOT LOCKED
The physical channel is not set in the LOCKED state.
10254
PHYSICAL CHANNEL GROUP NAME ALREADY
RESERVED
The name of the physical channel group is already in use.
Issue: 30-0
DN987378
289
Error messages
General Error Messages of System
10255
MAXIMUM NUMBER OF PHYSICAL CHANNELS
CREATED TO GIVEN CHANNEL GROUP
The maximum number of physical channels has already
been created to the given channel group.
10256
PHYSICAL CHANNEL NOT IN GIVEN CHANNEL GROUP
The physical channel does not belong to the given channel
group.
10257
ONLY ONE PHYSICAL CHANNEL IN CHANNEL GROUP
An attempt has been made to remove the last physical
channel from the physical channel group.
10258
ET UNIT NOT IN WORKING STATE
The state of the ET unit is not WO-EX.
10259
TRANSACTION COMMITTED
The transaction has been executed successfully and
committed to, but then the transaction hand has failed. The
special hand Raveller has fulfilled the job.
10260
ERROR IN DBFILS FILE
The contents of the DBFILS file of the database in
question are erroneous.
10261
ERROR IN DBSMAN PROGRAM BLOCK OF DATABASE
SYSTEM
The operator has asked for database loading but the
DBSMAN program block does not reply to the load request
sent by the database manager.
10262
CONFLICT WITH PPSUBR FILE
A conflict with the local payphone line supervision file
(PPSUBR) has been detected.
10263
ERROR IN BUFFER TRANSFER SERVICE (BUFFER IS
LOST)
The error may occur when using the asynchronous buffer
transfer service SEND_DATA_IN_BUF_ASYNC (the
MOVIES library). The fault is a result of the situation in
which the application has given the buffer to the MOPSUS
family and that the communication between the MOPSUS
family and the application breaks before the connection
was released. The fault is highly improbable.
10264
290
ERROR IN READING APFILE FILE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The reading of the application file of the network operator
(APFILE) has failed.
10265
ERROR IN WRITING INTO APFILE FILE
The writing into the application file of the network operator
(APFILE) has failed.
10266
ERROR IN READING NEUSER FILE
The reading of the network user file (NEUSER) has failed.
10267
ERROR IN WRITING INTO NEUSER FILE
The writing into the network user file (NEUSER) has failed.
10268
ERROR IN READING AFROFI FILE
The reading of the application field id and process family id
file (AFROFI) has failed.
10269
APPLICATION FIELD ALREADY EXISTS
An attempt has been made to add a privilege to the
application field to which the user already has a privilege.
10270
NETWORK USER DOES NOT EXIST
The network user identifier does not exist.
10271
NETWORK USER ALREADY EXISTS
An attempt has been made to add a network user identifier
which already exists.
10272
INVALID USER IDENTIFICATION
The user identification is either not a network user id, or
the given password is not correct.
10273
INQUIRY NOT COMPLETED
The inquiry, the answer of which requires several
messages, is not completed. The error message is the
value of the status field of an other than the last message
10274
RULE ALREADY EXISTS
The rule, which is being added into a rulebase, already
exists in this rulebase.
10275
DISK UPDATES ARE PREVENTED IN THIS DATABASE
The operator has prevented disk updates. However, he
asks the database system to dump the database onto disk.
10276
Issue: 30-0
APPLICATION ENTITY TITLE ALREADY RESERVED
DN987378
291
Error messages
General Error Messages of System
The AET is already used by an application.
10277
GIVEN APPLICATION ENTITY TITLE IDENTIFIES
REMOTE APPLICATION
The application entity title (AET) given in the command
identifies a remote application. Only the application entity
title has been defined for the remote application.
10278
GIVEN APPLICATION ENTITY TITLE IDENTIFIES LOCAL
APPLICATION
The application entity title (AET) given in the command
identifies a local application.
10279
NO RESPONSE FROM IOMANA
The TEXTPR program block has sent a task to the
IOMANA program block which has not responded within
the time limit.
10280
ERROR IN DATABASE ADDRESS
The database address is incorrect.
10281
COMMUNICATION ERROR BETWEEN O7MANA AND
O7AMAN
Communication between O7MANA and O7AMAN program
blocks has failed.
10282
ANALOG TERMINAL NOT FOUND FROM ATFILE
The analog terminal device marked in the physical channel
file (OPCFIL) is not found from the analog data terminal file
(ATFILE).
10283
PHYSICAL CHANNEL ALREADY EXISTS
Physical channel already exists.
10284
PHYSICAL TERMINAL DOES NOT EXIST
There is no free physical terminal in the computer unit. The
analog terminals have been listed in the ATFILE file, and
the digital ones in the MUFILE file.
10285
PHYSICAL TERMINAL ALREADY RESERVED
The physical terminal is already used by a physical
channel.
10286
X25 PARAMETER SET DOES NOT EXIST
The given X25 parameter set is not found from the
OPHX25 file.
292
DN987378
Issue: 30-0
General Error Messages of System
10287
Error messages
X25 PARAMETER SET NOT FOUND
The X25 parameter set marked in the physical channel file
(OPCFIL) is not found from the OPHX25 file.
10288
PHYSICAL CHANNEL USES DIGITAL TERMINAL
The physical channel uses a digital terminal.
10289
PHYSICAL CHANNEL USES ANALOG TERMINAL
The physical channel uses an analog terminal.
10290
LI2M CONNECTION OFF
Measurement of a multiplexer subscriber line fails. In error
situations in 2M connections, SSPPGM program block
responds with a congestion in the descending direction.
10291
ERROR BETWEEN MUX AND SUB
Measurement of the multiplexer subscriber line fails.
Communication between MUX and SUB-C failed.
10292
INCORRECT TIME SLOT
Measurement of the multiplexer subscriber line fails. The
time slot has to be less than 32.
10293
WRONG OR ERRONEOUS OPERAND IN WATSON FILE
In the checks of the WATSON file, there is an operand that
is of a wrong type or otherwise incorrect.
10294
UNDEFINED OPERATION IN WATSON FILE
The check definition in the WATSON file is incorrect.
10295
VALUE IN DISK FILE IS INCONSISTENT WITH THE
DEFINITION IN WATSON FILE
The contents of the disk file do not meet the validity
requirements defined for it.
10296
CHECKING OF DISK FILE EXCEEDS DATA AREA LIMIT
The check defined in the WATSON file in incorrect in that
the reference to the file to be checked is directed outside
the data area.
10297
PREVIOUS LOGBUFFER SAVE FAILED
Saving of the previous logbuffer has failed.
10298
DISK WRITE FAILURE
Writing into the disk file does not succeed.
Issue: 30-0
DN987378
293
Error messages
General Error Messages of System
10299
EIOLIB: AREA TOO SMALL
The pointer given to the EIOLIB-program block points to a
memory segment that is too small. The execution of the
task would lead to a memory protection error.
10300
MESSAGE BUFFER ALLOCATION ERROR
The EIOLIB program block could not allocate a message
buffer for a task message.
10301
WRONG REPLY
The EIOLIB program block has received an incorrect reply
from the EIDPRO program block.
10302
EIDPRO PROGRAM BLOCK NOT ACCESSABLE
No connection can be made to the EIDPRO program block
in a computer with disk.
10303
ACKNOWLEDGEMENT TIME-OUT
The acknowledgement of a successful writing task has
ended up in time-out.
10304
INVALID TASK IDENTIFICATION
The task identification in the task message of the EIDPRO
program block is incorrect.
10305
INVALID COMPUTER ADDRESS
The unit address given to the EIOLIB program block is
either a broadcast address or a logical address with
distribution extent WO+SP.
10306
NO SUCH DEVICE IN UNIT
The unit does not have the desired peripheral device, or
the DSKLIB program block is not in use.
10307
WRITING IN DIRECTORY FILE NOT ALLOWED
An attempt has been made to write in a file that is a
directory.
10308
CONFLICT BETWEEN NETWORK ELEMENT INDEXES
There is a conflict between network element indexes.
10309
REQUESTED TASK ALREADY DONE
Operator has asked some task to be done by database
system but the task has already been done.
10310
294
PLUG-IN UNIT DOES NOT RESPOND
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The plug-in unit does not respond.
10311
O7AMAN DOES NOT RESPOND
The OSI address and routing program block (O7AMAN)
does not respond.
10312
PLUG-IN UNIT PARAMETERS ARE INCONSISTENT
The plug-in unit parameters are inconsistent.
10313
ODCMAN HAS BEEN REQUESTED ILLEGAL PLUG-IN
UNIT STATE TRANSITION
ODCMAN program block has been requested an illegal
plug-in unit state transition.
10314
HAND INITIALIZATION HAS FAILED
A hand initialization has failed.
10315
INITIALIZATION OF ALL HANDS HAS FAILED
The initialization of all hands has failed.
10316
HAND HAS FAILED
A hand has failed.
10317
FILE OPENING HAS FAILED
A file opening has failed.
10318
NO APPROPRIATE INTERFACE TASK FOR VOPS
MESSAGE
There is not an appropriate interface task for the VOPS
message.
10319
VOPS PROCESS IS OUT OF MEMORY
A VOPS process is out of memory.
10320
TOO BIG MEMORY ALLOCATION REQUEST BY VOPS
PROCESS
A VOPS process has made a too big memory allocation
request.
10321
NO CHANNELS AVAILABLE IN CHANNEL GROUP
The outgoing call is rejected because all potential channels
are either locked or out of order.
10322
Issue: 30-0
NO LOCAL ADDRESSES AVAILABLE FOR OUTGOING
CALL
DN987378
295
Error messages
General Error Messages of System
The outgoing call is rejected because there is no proper
local address for the possible channels. Check the
administrative and the functional state of the local
addresses. Check also the possible address restrictions of
the channels belonging to the selected channel groups.
10323
UNABLE TO SOLVE OUTGOING CALL
The outgoing call is rejected because no proper channel is
available to the destination. Check the administrative and
the functional state of the channels belonging to the
channel groups used by the remote end application.
10324
REMOTE NSAP NOT FOUND IN FILE OADFIL
The call is rejected because the remote NSAP is not found
in the address database. Check from the address
database that the address is correct.
10325
LOCAL NSAP NOT FOUND IN FILE OADFIL
The call is rejected because the local NSAP is not found in
the address database. Check from the address database
that the address is correct.
10326
LOCAL SSAP NOT FOUND IN FILE OADFIL
The call is rejected because the local SSAP is not found in
the address database. Check from the address database
that the address is correct.
10327
LOCAL PSAP NOT FOUND IN FILE OADFIL
The call is rejected because the local PSAP is not found in
the address database. Check from the address database
that the address is correct.
10328
LOCAL NSAP NOT IN USE
The call is rejected because the administrative state of the
channel is LOCKED. Check if this is necessary.
10329
LOCAL PSAP NOT IN USE
The call is rejected because the administrative state of the
address is LOCKED. Check if this is necessary.
10330
WRONG ADDRESS TYPE IN FILE OADFIL
There is a conflict between the address and the application
database. The type of the address and the type of the
owner of the address mismatch.
10331
INVALID REFERENCE TO FILE OADFIL
There is a conflict between the address and the application
database.
296
DN987378
Issue: 30-0
General Error Messages of System
10332
Error messages
INVALID REFERENCE TO FILE OPCFIL
There is a conflict between the channel and the channel
group database.
10333
INVALID REFERENCE TO FILE OAPFIL
There is a conflict between the address and the application
database.
10334
INVALID REFERENCE TO FILE OCGFIL
There is a conflict between the address and the channel
group database.
10335
INVALID REFERENCE TO FILE OOAFIL
There is a conflict between the address and the application
parameter database.
10336
INVALID REFERENCE TO FILE OAEFIL
There is a conflict between the address and the
Application Entity Title database.
10337
INVALID REFERENCE TO FILE OCSFIL
Internal error in the current sessions database handling.
Out of free records.
10338
REFERENCE TO AN UNALLOCATED RECORD IN FILE
OADFIL
There is conflict between application/access control and
address database. Check the configuration information.
10339
REFERENCE TO AN UNALLOCATED RECORD IN FILE
OAPFIL
There is a conflict between the application and the address
database. Check the configuration information.
10340
REFERENCE TO AN UNALLOCATED RECORD IN FILE
OCGFIL
There is a conflict between the address and the channel
group database. Check the configuration information.
10341
REFERENCE TO AN UNALLOCATED RECORD IN FILE
OPCFIL
There is conflict between the channel group and the
channel database. Check the configuration.
10342
Issue: 30-0
REFERENCE TO AN UNALLOCATED RECORD IN FILE
OOAFIL
DN987378
297
Error messages
General Error Messages of System
The call is rejected because there is a conflict between the
address and the application parameter database. Check
the configuration information.
10343
REFERENCE TO AN UNALLOCATED RECORD IN FILE
OAEFIL
The call is rejected because there is a conflict between the
address and the Application Entity Title database. Check
the configuration information.
10344
WRONG APPLICATION TYPE IN FILE OAPFIL
The incoming call is rejected because there is a conflict
between the type of the address and the type of the owner
of the address. Check the contents of the application and
the address database.
10345
FILE OCGFIL DOES NOT CONTAIN THIS CHANNEL
GROUP NAME
The outgoing call is rejected because the channel group
name is not found in the channel group database. Check
the configuration information.
10346
FILE OAPFIL DOES NOT CONTAIN THIS LOCAL
APPLICATION NAME
The calling local application is not found in the application
database. Check the configuration information.
10347
FILE OAPFIL DOES NOT CONTAIN THIS REMOTE
APPLICATION NAME
The calling remote end application is not found in the
application database. Check the configuration information.
10348
FILE OADFIL DOES NOT CONTAIN THIS REMOTE
PSAP
The calling remote end PSAP is not found in the address
database. Check the configuration information.
10349
NUMBER OF AS7 PLUG-IN UNIT NOT IN MUFILE
The number of the plug-in unit is incorrect.
10350
NUMBER OF AS7 PLUG-IN UNIT NOT IN NECONF
The number of plug-in unit is incorrect.
10351
NUMBER OF CHANNEL NOT IN NECONF
The number of channel is incorrect.
10352
298
ILLEGAL NUMBER OF CHANNEL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The number of channel is incorrect.
10353
PHYSICAL CHANNEL IS ASSOCIATED TO PHYSICAL
CHANNEL GROUP
The physical channel has been associated with a physical
channel group.
10354
ACTIVE PCM-TSL ALREADY RESERVED
The active PCM TSL is already reserved.
10355
PASSIVE PCM-TSL ALREADY RESERVED
The passive PCM TSL is already reserved.
10356
DISK FILE COPYING FAILED
Too many errors occurred in disk file copying, so the
copying is interrupted.
10357
DATA BLOCK INCORRECT
The data block structure is not as agreed. The records are
too short, too long, or their lengths do not match with the
length of the data block.
10358
PBX INTERFACE NAME EXISTENT
The name of the PBX interface already exists.
10359
PBX INTERFACE NAME NONEXISTENT
The name of the PBX interface does not exist.
10360
NOT ROTARY DIALLING TELEPHONE
The phone is not a rotary dialing phone in the central
memory (CM). The operation failed.
10361
MOVIES LIBRARY NOT AVAILABLE IN UNIT WITH DISK
The EIOLIB library fails in a task requiring data transfer
because there is no MOVIES library available in a unit with
disk.
10362
MOVIES NOT AVAILABLE IN OWN UNIT
The EIOLIB library fails in a task requiring data transfer
because there is no MOVIES library available in its own
unit.
10363
NO ASS CHANNELS FOR LTEST PLUG-IN UNITS
AVAILABLE IN PCMCON
No ASS channels for the LTEST plug-in units are available
in the PCMCON file. The operation failed.
Issue: 30-0
DN987378
299
Error messages
General Error Messages of System
10364
PHYSICAL CHANNEL IS NOT IN UNL-DIS STATE
The physical channel is not in the UNLOCKED-DISABLED
state.
10365
PHYSICAL CHANNEL IS NOT IN UNLOCKED STATE
The physical channel is not in the UNLOCKED state.
10366
PHYSICAL CHANNEL IS ALREADY IN LOCKED STATE
The physical channel is already in the LOCKED state.
10367
PHYSICAL CHANNEL IS NOT IN LOCKED STATE
The physical channel is not in the LOCKED state.
10368
NO ROOM FOR DATA AREA
There is not enough space in the memory for the data area
to be reserved.
10369
NO SWI PCMS
The amount of SWI PCMs is out of the ordinary.
10370
NO OWN COMSIG EXTERNAL PCMS IN USE
The own COMSIG program block has no external PCMs in
use.
10371
MODULE NOT IDENTICAL ON BOTH DISKS
The contents of the load module are not identical on the
two hard disks.
10372
FILE ERROR IN SNMCSE
An error has occurred when processing a file in SNMCSE
program block.
10373
TIMEOUT IN SNMCSE
A timeout has occurred in SNMCSE program block.
10374
CONNECTION FAILURE IN SNMCSE
The connection tried by SNMCSE program block has
failed.
10375
UNSUCCESSFUL SNMCSE TASK
A task executed by SNMCSE program block has failed
because of the environment.
10376
SYSTEM NAME ALREADY USED BY GIVEN NAME
The system name is incorrect.
300
DN987378
Issue: 30-0
General Error Messages of System
10377
Error messages
SYSTEM IDENTIFIER ALREADY USED BY GIVEN CNUMBER
The system identifier is incorrect.
10378
NO FREE DISKFILES
There are no free files available on the disk for detailed
charging storing.
10379
OSI ADDRESS IS NOT IN UNL-DIS STATE
The OSI address is not in the UNLOCKED-DISABLED
state.
10380
OSI ADDRESS IS ALREADY IN LOCKED STATE
The OSI address is already in the LOCKED state.
10381
OSI ADDRESS STATE CHANGE FAILED
Changing the state of the OSI address failed.
10382
INCORRECT DATA IN OSCFIL FILE
The OSCFIL file contains incorrect data when compared to
the OPCFIL file. See alarm 2261 CONFLICT BETWEEN
TWO FILES.
10383
D-CHANNEL FOR SUBSCRIBER MODULE DOES NOT
EXIST
No D-channel for the subscriber module does exist.
10384
D-CHANNEL FOR SUBSCRIBER MODULE ALREADY
EXISTS
A D-channel for the subscriber module already exists.
10385
PXNETM NOT IN ACTIVE STATE
The PXNETM program block is not in active working state.
10386
NO FREE TERMINAL FUNCTIONS AVAILABLE
No free terminal functions in AS7U are available.
10387
PCM/TSL ALREADY USED IN OTHER D-CHANNEL
The PCM/TSL is already used in another D-channel.
10388
COMMUNICATION ERROR BETWEEN PXADMI AND
OTHER PROGRAM BLOCK
A communication error between PXADMI and some other
program block. See
PROCESS_COMMUNICATION_ERROR failure flag.
Issue: 30-0
DN987378
301
Error messages
General Error Messages of System
10389
AS7U TERMINAL NOT INITIALIZED
The AS7U terminal was not initialized.
10390
PAD CONNECTION FAILED
The PAD-connection function has returned an error in
status.
10391
PAD COMMUNICATION FAILURE
The PAD-communication function has returned an error in
status.
10392
DSP PROGRAM NOT FOUND IN SOFTWARE PACKAGE
OF MFST PLUG-IN UNIT
The requested program of the DSP (Data Signalling
Processor) is not found in the memory of the 80186
processor when loading a program code of the DSP from
the memory of the 80186 processor to the external
memory of the DSP.
10393
DATA SIGNALLING PROCESSOR CODE RAM WRITE
ERROR
Writing in the program memory (external RAM memory of
the DSP) of the DSP in the MFST plug-in unit does not
succeed when loading program code into the DSP. The
reason for the failure may be a faulty plug-in unit or an
incorrect program package of the MFST plug-in unit.
10394
ILLEGAL DSP PROGRAM TYPE
The type of the data signalling processor (DSP) program is
illegal.
10395
DATA SIGNALLING PROCESSOR STATE CHANGE
FAILED
The state change of a data signalling processor (DSP) has
failed in theMFST plug-in unit.
10396
PARAMETER VALUE REQUIRED FOR INITIALIZATION
MFST HW IS INCORRECT
The value of a parameter given in
MFST_INIT_PARAMETERS message is incorrect.
10397
NO ACKNOWLEDGEMENT TO DSP CODE LOAD
REQUEST
No acknowledgement to a
LOAD_CMD_DSP_PROGRAMS message is received
from the MFLOAD program block in the MFST plug-in unit.
10398
302
ILLEGAL NUMBER OF SYSTEM
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The number of system is incorrect.
10399
ILLEGAL NAME OF SYSTEM
The name of system is incorrect.
10400
NUMBER OF MFST CHANNEL IS INCORRECT
The number of an MFST channel is incorrect.
10401
ATTEMPT TO USE UNUSED MFST CHANNEL
An attempt has been made to use an uninitialized MFST
channel in the MFST plug-in unit.
10402
ATTEMPT TO USE UNIMPLEMENTED SIGNALLING
TYPE IN MFST
An attempt has been made to use an unimplemented
signalling type in an MFST plug-in unit.
10403
CONFLICT WITH INITIALIZED AND REQUESTED
SIGNALLING TYPE
The requested signalling type is different from the
initialized signalling type in an MFST channel in an MFST
plug-in unit.
10404
ATTEMPT TO OPEN ALREADY OPENED MFST
CHANNEL
An attempt has been made to open an MFST channel that
was already opened.
10405
ATTEMPT TO CLOSE UNOPENED MFST CHANNEL
An attempt has been made to close an MFST channel that
was not opened.
10406
GIVEN FILE NOT FOUND IN THE MEFILE OF SOURCE
DIRECTORY
The name or the identification number of the given file is
not found in the MEFILE of the source directory.
10407
GIVEN FILE NOT FOUND IN THE MEFILE OF
DESTINATION DIRECTORY
The name or the identification number of the given file is
not found in the MEFILE of the destination directory.
10408
FILE MEFILE DOES NOT EXIST IN SOURCE
DIRECTORY
File MEFILE does not exist in the source directory.
Issue: 30-0
DN987378
303
Error messages
General Error Messages of System
10409
FILE MEFILE DOES NOT EXIST IN DESTINATION
DIRECTORY
File MEFILE does not exist in the destination directory.
10410
ERROR OCCURRED WHEN READING FILE MEFILE IN
SOURCE DIRECTORY
An error occurred when reading file MEFILE in the source
directory.
10411
ERROR OCCURRED WHEN READING FILE MEFILE IN
DESTINATION DIRECTORY
An error occurred when reading file MEFILE in the
destination directory.
10412
ERROR OCCURRED WHEN READING FILE DXPFIL IN
DESTINATION DIRECTORY
An error occurred when reading file DXPFIL in the
destination directory.
10413
ERROR OCCURRED WHEN READING FILE DXPFIL IN
SOURCE DIRECTORY
An error occurred when reading file DXPFIL in the source
directory.
10414
FILE DXPFIL DOES NOT EXIST IN SOURCE
DIRECTROY
File DXPFIL does not exist in the source directory.
10415
FILE DXPFIL DOES NOT EXIST IN DESTINATION
DIRECTORY
File DXPFIL does not exist in the destination directory.
10416
GIVEN FILE NOT FOUND IN THE DXPFIL OF SOURCE
DIRECTORY
The name or the identification number of the given file is
not found in the DXPFIL of the source directory.
10417
GIVEN FILE NOT FOUND IN THE DXPFIL OF
DESTINATION DIRECTORY
The name or the identification number of the given file is
not found in the DXPFIL of the destination directory.
10418
GIVEN FILE NOT FOUND IN THE MAFILE OF
DESTINATION DIRECTORY
The name or the identification number of the given file is
not found in the MAFILE of the destination directory.
304
DN987378
Issue: 30-0
General Error Messages of System
10419
Error messages
FILE MAFILE DOES NOT EXIST IN DESTINATION
DIRECTORY
File MAFILE does not exist in the destination directory.
10420
ERROR OCCURRED WHEN READING FILE MAFILE IN
DESTINATION DIRECTORY
An error occurred when reading file MAFILE in the
destination directory.
10421
ERROR OCCURRED WHEN READING FILE FILCAT IN
SOURCE DIRECTORY
An error occurred when reading file FILCAT in the source
directory.
10422
FILE FILCAT DOES NOT EXIST IN SOURCE
DIRECTORY
File FILCAT does not exist in the source directory.
10423
GIVEN FILE NOT FOUND IN THE FILCAT OF SOURCE
DIRECTORY
The name or the identification number of the given file is
not found in the FILCAT of the source directory.
10424
GIVEN FILE NOT FOUND IN THE GINTON OF SOURCE
DIRECTORY
The name or the identification number of the given file is
not found in the GINTON of the source directory.
10425
FILE GINTON DOES NOT EXIST IN SOURCE
DIRECTROY
File GINTON does not exist in the source directory.
10426
ERROR OCCURRED WHEN READING FILE GINTON IN
SOURCE DIRECTORY
An error occurred when reading file GINTON in the source
directory.
10427
PERMANENT VIRTUAL CIRCUIT IS NOT DEFINED IN
X25 PARAMETER SET
The permanent virtual channel (PVC) has not been defined
in the X25 parameter set (file OPHX25) used by the
physical channel.
10428
CIRCUIT STATE CHANGE LOCAL
Circuit state in co-exchange is unknown.
10429
Issue: 30-0
NO FREE DATA TERMINALS IN COMPUTER UNIT
DN987378
305
Error messages
General Error Messages of System
There are no free data terminals in the computer unit.
10430
X25 PARAMETER SET ALREADY EXISTS
The X25 parameter set already exists.
10431
PHYSICAL CHANNEL IS ASSOCIATED TO X25
PARAMETER SET
The physical channel is associated to the X25 parameter
set.
10432
UNLOCKED PHYSICAL CHANNEL IS ASSOCIATED TO
X25 PARAMETER SET
The X25 parameter set is associated to the physical
channel which is in the UNLOCKED state.
10433
DSP SUPERVISION FLAG CLEARING ERROR
The supervision program block of the DSP (Data Signalling
processor) has found that the DSP does not clear the
supervision flag.
10434
O&M CONNECTION NOT AVAILABLE
External messages cannot be sent. Check the O&M
connection.
10435
LOW FEED LIMIT
Overload information of the power supply of the subscriber
module. The overload is low but it inhibits the
measurement.
10436
MEDIUM FEED LIMIT
Overload information of the power supply of the subscriber
module. The overload is medium level and it inhibits the
measurement.
10437
HIGH FEED LIMIT
Overload information of the power supply of the subscriber
module. The overload is high and it inhibits the
measurement.
10438
DSP PROGRAM CODE VERIFY ERROR
The supervision function of DSP code has found that the
program code of the DSP has changed in the code RAM of
the DSP.
10439
LIA COMMUNICATION FAILURE
Communication failure between the LIA10 and SBCN plugin units.
306
DN987378
Issue: 30-0
General Error Messages of System
10440
Error messages
HOME METERING PULSE CONGESTION
Home metering pulse congestion.
10441
SBLTI COMMUNICATION FAILURE
Communication failure between SBLTI and SBCN plug-in
units.
10442
SBLTI BUSY
The SBLTI plug in unit is busy.
10443
SBLTI FAULTY
The SBLTI plug-in unit is faulty.
10444
NO TEST IN SBLTI
There is no test under execution in the SBLTI plug-in unit.
10445
INCOMING CALL
A call is coming in during a test.
10446
LIA TEST CONNECTION TIME LIMIT
Test connection time limit in the LIA10 plug-in unit.
10447
OTHER TEST IS RUNNING IN MODULE
The operation fails. There is another test under execution
in the subscriber module.
10448
VIRTUAL CIRCUIT NUMBERS ARE NOT COMPATIBLE
Virtual circuit numbers are not compatible. See /X25
Configuration Parameters Handling, Command Manual,
2.6/.
10449
CONFLICT BETWEEN MAXIMUN NSDU LENGTH AND
USER DATA SIZE
Network service data unit length and user data size are not
compatible.
10450
REPEATED RESTART IN UNIT
Repeated restart in the ECU/MPC/DIPC/DIC unit.
10451
PREPROCESSOR PROGRAM CHECK SUM ERROR
The check sum of one or more programs is incorrect in the
preprocessor.
10452
PREPROSESSOR START-UP RAM TEST ERROR
The error(s) in the RAM memory of the preprosessor has
been found by the start-up RAM test of the preprocessor.
Issue: 30-0
DN987378
307
Error messages
General Error Messages of System
10453
CONFLICT BETWEEN REQUESTED OPERATION AND
GIVEN SYSTEM LEVEL
There is a conflict between the requested operation and
given system level.
10454
CONFLICT BETWEEN FILE IDENTIFIER AND FILE
NAME
There is a conflict between the file identifier and file name.
10455
MEASURING DEVICE NOT FOUND
A measuring device is not found from the configuration file
for subscriber network measurement interfaces
(XMCONF). The reason for this is one of the following: 1.
The measuring device is not defined in the file. 2. The
device is defined in the file, but the module of the line to be
measured is not connected to it. 3. The device is defined in
the file and the module of the measured line is connected
to it, but the subscribers of the module corresponding to
the module type in the subscriber maintenance
information, can not be measured with the measuring
device. In this case the fault is either in the central memory
maintenance information or in the XMCONF file.
10456
O&M CHANNEL STATE CHANGE NOT POSSIBLE
The state transition of the operation and maintenance
channel is not possible.
10457
O&M CHANNEL NOT IN WORKING STATE
The state of the operation and maintenance channel is
incorrect.
10458
LINE NOT DEFINED IN PPSUBR FILE
Data on the line is missing from the local payphone
supervision file (PPSUBR). The operation has failed.
10459
MAXIMUM VIRTUAL CIRCUIT NUMBER EXCEEDED
The maximum virtual circuit number has been exceeded.
The maximum number is 255.
10460
RESERVATION OF EIDPRO HAND FAILED
All the hands of the EIDPRO process family are reserved,
and the reservation of a hand does not succeed. This fault
situation may occur when there are several disk writings,
but it may also be a sign of errors (hands are dead).
10461
308
INITIALIZATION OF HANDS IN EIDPRO PROCESS
FAMILY FAILED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The initialization of hands has failed, and the execution of
file operations is not possible. The master of the EIDPRO
process family sends a reply message with this error
message to all disk file operation requests.
10462
D-CHANNEL ALREADY EXISTS
The given D-channel already exists.
10463
D-CHANNEL DOES NOT EXIST
The given D-channel does not exist.
10464
PHYSICAL CHANNEL NOT IN DISABLED STATE
The physical channel is not in the DISABLED state.
10465
PHYSICAL CHANNEL ALREADY IN UNLOCKED STATE
The physical channel is already in the UNLOCKED state.
10466
PHYSICAL CHANNEL IS SHUTTING DOWN
The physical channel is shutting down, and the next
administrative state of the physical channel has to be
LOCKED.
10467
ANALOG DATA TERMINAL DOES NOT EXIST
The analog data terminal is not found with the given
parameters (search key) from the ATFILE file.
10469
DIRECTORY ENTRY DOES NOT EXIST
There is no directory entry for the given object, or no
directory entry with the given key value.
10470
ANALOG DATA TERMINAL ALREADY EXISTS
The analog data terminal already exists in the ATFILE file.
10471
GIVEN PLUG-IN UNIT NOT IN MUFILE FILE
The given plug-in unit is not found in the MUFILE file. Use
WHP command to add a new plug-in unit.
10472
UNLOCKED PHYSICAL CHANNEL CONNECTED TO
ANALOG DATA TERMINAL
An unlocked physical channel is connected to an analog
data terminal (physical channel is in UNLOCKED state).
10473
PHYSICAL CHANNEL CONNECTED TO ANALOG DATA
TERMINAL
The physical channel is connected to an analog data
terminal.
Issue: 30-0
DN987378
309
Error messages
General Error Messages of System
10474
FEED VOLTAGE ERROR
The polarity is incorrect, or the feed is missing totally.
10475
DIRECTORY ENTRY ALREADY EXISTS
The directory entry for an object already exists, or if the
directory key is unique, there is already a directory entry
with the same key value as in the object to be inserted.
10476
PRIMITIVE ITEM IS INVALID
The operation succeeded completely.
10477
MODE PARAMETER IS INVALID
The operation succeeded completely.
10478
ERROR PARAMETER IS INVALID
The operation succeeded completely.
10479
OBJECT CLASS PARAMETER IS INVALID
The operation succeeded completely.
10480
OBJECT INSTANCE PARAMETER IS INVALID
The operation succeeded completely.
10481
ATTRIBUTE LIST PARAMETER IS MISSING
The operation succeeded completely.
10482
ATTRIBUTE PARAMETER IS INVALID
The operation succeeded completely.
10483
EVENT IDENTIFIER IS INVALID
The operation succeeded completely.
10484
ACTION IDENTIFIER IS INVALID
The operation succeeded completely.
10485
ATTRIBUTE IDENTIFIER PARAMETER IS INVALID
The operation succeeded completely.
10486
HAND SHAKE MESSAGE NUMBER IS INCORRECT
The operation succeeded completely.
10487
DESTINATION APPLICATION DOES NOT ACCEPT THE
DATA TRANSFER
The operation succeeded completely.
310
DN987378
Issue: 30-0
General Error Messages of System
10488
Error messages
HAND SHAKE MESSAGE TYPE IS INVALID
The operation succeeded completely.
10489
APPLICATION DATA RECEIVED IS TOO BIG
The operation succeeded completely.
10490
COMMUNICATION ERROR BETWEEN O7MANA AND
DUMPER
Communication between the O7MANA and DUMPER
program blocks has failed.
10491
SUBSCRIBER NUMBER NOT FREE
The subscriber number analysis can not be destroyed
unless the number is in FREE state.
10492
ILLEGAL TRUNK CODE
The trunk code is incorrect.
10493
UNKNOWN ANALYSIS CASE
The analysis case is unknown.
10494
NO ET FOR ACTIVE PCM
There is no ET for an active PCM.
10495
NO ET FOR SPARE PCM
There is no ET for a spare PCM.
10496
O&M CHANNEL NOT IN SEPARATED STATE
The state of the operation and maintenance channel is
incorrect.
10497
TRIGGER RECORD NONEXISTENT
The trigger record does not exist.
10498
TRIGGER RECORD EXISTENT
The SPCROU record contains trigger data.
10499
COMMUNICATION FAILURE WITH OTHER UNIT
Message transfer to the adjacent synchronization unit is
not possible. This is probably due to a hardware failure
either in this or in the adjacent unit, or in the cartridge
subrack.
10500
Issue: 30-0
SWITCHOVER FAILURE IN HARDWARE
DN987378
311
Error messages
General Error Messages of System
Switchover was attempted, but it failed in CL1TG/CL2TG.
This may be due to a hardware failure in this or the other
syncronisation unit or in the cartridge hardware. Check
also the position of the forced control switches in both
syncronisation units.
10501
STATE CHANGE NOT POSSIBLE DUE TO ACTUAL
STATES OF CLS UNITS
State change is not possible, for example from SE-state to
SP-state.
10502
DIAGNOSTIC TESTS ON IN CLS UNIT
State change is not possible because there are diagnostic
programs running in the syncronization unit
10503
NO CHARGING PARAMETERS
Charging parameters are missing, when there is an
Intelligent Network route in special route file and charging
index is 0.
10504
INTERNAL CIRCUIT GROUP DOES NOT EXIST
The internal circuit group does not exist.
10505
INTERNAL PCM NOT CONNECTED TO INTERNAL
ROUTE
The internal PCM has not been connected to an internal
route to which the time slots of the terminal belong.
10506
CIRCUIT GROUP CREATION FAILED
Creation of the internal circuit group failed.
10507
CIRCUIT GROUP DELETION FAILED
Deletion of the internal circuit group failed.
10508
CIRCUIT ADDITION TO CIRCUIT GROUP FAILED
Addition of an internal circuit into an internal circuit group
failed.
10509
CIRCUIT DELETION FROM CIRCUIT GROUP FAILED
Deletion of an internal circuit from an internal circuit group
failed.
10510
EXTERNAL ROUTING FAILURE
External routing failure.
10511
312
COMMUNICATION ERROR BETWEEN O7MANA AND
CM3PRO PROGRAM BLOCKS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Communication failure between the O7MANA and
CM3PRO program blocks (O7MANA did not receive an
answer from CM3PRO before a time-out).
10512
CIRCUIT GROUP UPDATING FAILED
Updating of the data of the routing files of CM3PRO
program block failed. Check the routing data with the
CGROUP MML (command group RC).
10513
MEASUREMENT DEVICE WAS NOT FOUND
There are no measurement devices defined in the system.
10514
INCORRECT SUBSCRIBER NUMBER IDENTIFICATION
There is not found any subscriber in the database with this
identification.
10515
TIMEOUT: NO RESPONSE FROM NETWORK LAYER
PAD software cleared the connection because the network
layer (X.25 software) did not respond to messages that
were sent to it. It is also possible that the network layer
never received the message because sending the
message failed at operating system level.
10516
CALL CLEARED BY REQUEST OF REMOTE DTE
PAD software cleared the connection because the remote
DTE sent an X.29 invitation-to-clear message. This is
considered to be the normal way to end a PAD session.
10517
NETWORK DISCONNECT INDICATION RECEIVED
The connection has been cleared either by the network
layer software or the remote DTE.
10518
TOO SMALL CREDIT GRANTED BY NETWORK LAYER
Each data message that the PAD software sends to the
network layer decreases its credit by 128 (or more) bytes.
The reason for disconnecting was that the initial credit
granted by the network layer was too small to send any
data messages at all.
10519
HARDWARE ALARM ON IN SYNCRONISATION UNIT
Switchover is prohibited by a hardware alarm in the
synchronization unit.
10520
NO RESPONSE FROM SPARE SYNCRONISATION UNIT
Switchover is not possible because the spare
synchronization unit does not respond. In the hardware the
switchover command is executed in the spare unit.
Issue: 30-0
DN987378
313
Error messages
General Error Messages of System
10521
MAFILE CORRESPONDING TO PAID NOT FOUND
The MAFILE file corresponding to the package identifier is
not found.
10522
MODULE EXISTS IN LOADLIST BUT NOT IN MAFILE
The module listed in the load list is not found in the
MAFILE file.
10523
INCORRECT DATA IN CS7PAR FILE
Incorrect data in CS7PAR file detected. For further
information, see alarm 2077 (CCS7 PROGRAM BLOCK
DATA FAILURE) and/or LOG FILE UTILITY.
10524
INCORRECT SUBSCRIBER TYPE
The subscriber type (e.g. analog/ISDN) indicates, which
facilities are possible in each case. Part of the facilities are
type-dependent. If an attempt is made to set a pure ISDN
facility to an analog subscriber, this ends in an error
situation.
10525
THIS MML TASK NOT ALLOWED AT THE MOMENT
This MML task is not allowed at this MML terminal at the
moment because it or some other MML task close to this
one is activated from another MML terminal at the same
time. Try again later.
10526
ERROR COUNTER LIMIT EXCEEDED
Error counter limit has been exceeded.
10527
TRUNK CODE EXISTENT
The trunk code already exists.
10528
TRUNK CODE NONEXISTENT
The trunk code does not exist.
10529
TRUNK CODE SHORTER
The existing trunk code is shorter than the given trunk
code.
10530
TRUNK CODE LONGER
The existing trunk code is longer than the given trunk
code.
10531
EXTENSION IN CENTREX HUNTING GROUP
The subscriber is a member of a Centrex hunting group.
314
DN987378
Issue: 30-0
General Error Messages of System
10532
Error messages
SUBSCRIBER HAS NO MULTIPLE SUBSCRIBER
NUMBERS
The subscriber has no multiple subscriber numbers.
10533
SUBSCRIBER HAS ALL MULTIPLE NUMBERS IN USE
A subscriber is allowed to have 8 multiple subscriber
numbers. If this is exceeded, an error notice is given.
10534
INCORRECT CENTREX GROUP
You can only belong to a Centrex hunting group if you are
a member of the same Centrex group.
10535
RSU SUBSCRIBER
The subscriber number is reserved for a RSU subscriber.
10536
RELATIONSHIP DOES NOT HOLD IN A SUPERSET FOR
THE RELATION
A relationship is to be added in a relation but the
relationship does not hold in some superset of the relation.
10537
PHYSICAL CHANNEL CONNECTED TO DIGITAL DATA
TERMINAL
The physical channel is connected to a digital data
terminal. Remove physical channel before deleting digital
data terminal.
10538
BSC OBJECT NOT FOUND IN RNW DATABASE
The Base Station Controller has not been created into the
RNW database.No other objects can be created before the
BSC object has been created.
10539
BCF OBJECT NOT FOUND IN RNW DATABASE
The Base Control Function object has not been created
into the database. There must be an existing BCF under
which a Base Station object can be created.
10540
BTS NOT FOUND IN RNW DATABASE
The Base Station has not been created into the RNW
database. There must be an existing BTS under which a
Transceiver, a Frequency Hopping System or an Adjacent
Cell object can be created.
10541
TRX NOT FOUND IN RNW DATABASE
The Transceiver has not been created into the RNW
database. There must be an existing TRX under which a
Radio Timeslot can be created.
Issue: 30-0
DN987378
315
Error messages
General Error Messages of System
10542
RADIO TSL NOT FOUND IN RNW DATABASE
The Radio Timeslot has not been created into the RNW
database.
10543
HOPPING SYSTEM NOT FOUND IN RNW DATABASE
The Frequency Hopping System has not been created into
the RNW database. There must be an existing FHS into
which a hopping Radio Timeslot can be connected.
10544
ADJACENT CELL WAS NOT FOUND IN RNW
DATABASE
The Adjacent Cell has not been created into the RNW
database.
10545
OBJECT WAS NOT CREATED
The database system has not succeeded in creating a new
object.
10546
END OF LOAD GROUP
End of load group was encountered.
10547
INTERNAL PCM IS NOT CONNECTED TO CIRCUIT
GROUP NAMED OSIAS7
The internal PCM has not been connected to an internal
circuit group to which the time slots of the terminal belong.
Name of the internal circuit group of the X.25 terminal is
OSIAS7.
10548
MAXIMUM NUMBER OF ADJACENT CELLS FOR ONE
BASE STATION EXCEEDED
One base station may have only a limited number of
neighbours. This number can not be exceeded.
10549
SOME BCF STILL EXISTS
There still are some Base Control Function objects under
the BSC to be deleted. All the objects under the BSC must
be deleted before deleting the BSC itself.
10550
SOME BTS STILL EXISTS
There are still Base Station objects under the BCF to be
deleted. All the objects under the BCF must be deleted
before deleting the BCF.
10551
FREQUENCY HOPPING SYSTEM IS IN USE
Frequency Hopping System is still used by some radio
timeslots. It can not be deleted before all the relations
between the FHS and radio timeslot objects are removed.
316
DN987378
Issue: 30-0
General Error Messages of System
10552
Error messages
HUNTING GROUP CALL NUMBER
A notice related to subscriber handling - inquiry, creation,
or deletion. The notice means that the subscriber is a
hunting group call number.
10554
PARAMETERS OF MAC FRAME SENT TO ETHERNET
DRIVER WERE ERRONEOUS
The parameters of the MAC frame sent to the Ethernet
driver were erroneous.
10555
ETHERNET DRIVER IS NOT READY TO SEND MAC
FRAMES TO ETHERNET
The Ethernet driver is not ready to send MAC frames to
the Ethernet.
10556
TOO MANY PACKETS RECEIVED FROM ETHERNET
The OISOIP program block cannot send the packets
received from the Ethernet to the network service user
because of the lack of the credit.
10557
MEMORY FILE UPDATES ARE FORBIDDEN.
Memory files should not be updated at the moment.
10558
PHYSICAL DATA TERMINAL NOT FOUND
Physical terminal of the channel is not found in the
OSCFIL file. Check the data of OSCFIL and OPCFIL files
on the manipulated channel.
10559
NOT A HUNTING GROUP CALL NUMBER
The call number given by the user is not a group call
number known by the hunting group handling MML
(SUHARI).
10560
SOWADM TIME-OUT
No response is received from the SOWADM program
block.
10561
FILE NOT IN UNION FILE
The file is not found in the union file.
10562
MODULE LOADED
All data of the module has already been loaded.
10563
TIME LIMIT EXCEEDED IN SBCN COMMUNICATION
Time limit exceeded in SBCN communication.
10564
Issue: 30-0
VACANT DPABX SUBSCRIBER NUMBER
DN987378
317
Error messages
General Error Messages of System
A free subscriber number found in the 1st or 2nd tree of
the digit analysis, and created for the use of a DPABX.
10565
RESERVED DPABX SUBSCRIBER NUMBER
The subscriber number is an existing DPABX number.
10566
AREA CODE NOT FOUND
No area code can be found in the parameter file PRFILE
with the area_code_id received from the subscriber
database.
10567
FILE EXISTS IN LOADLIST BUT NOT IN MEFILE
A file in the load list is not found in the MEFILE file.
10568
SWITCHOVER IN SYNCRONISATION UNIT DURING
COMMAND EXECUTION
Command failed because of a switchover during command
execution.
10569
UNEXPECTED CURRENTS IN LINE
In subscriber line measurement, currents of wrong
direction were detected. It is possible that there is short
circuit or external voltages on the line. The measurement
results are not reliable.
10571
NON EXISTENT PIU
The PIU does not exist.
10572
ERROR OCCURRED IN DATABASE CONVERSION
An error has occurred in database conversion. See printouts and error logs for the cause of the error.
10573
NO MATCHING RULES TO BE DELETED
No rules matching the given parameters are found in the
alarm system rulebase. No rules are deleted.
10574
NO MATCHING RULES TO BE MODIFIED
No rules matching the given parameters are found in the
alarm system rulebase. No rules are modified.
10575
NO MATCHING RULES TO BE RESTORED
No previously deleted, restorable rules matching the given
parameters are found in the alarm system rulebase. No
rules can be restored.
10576
318
BOOT LOADING FAILED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The software package intended for the computer is not
available.
10577
PLUG-IN UNIT RESTARTED
Plug-in unit has been restarted.
10578
MISSING INTERFACE PLUG-IN UNIT
Interface plug-in unit is missing.
10580
SEMIPERMANENT CONNECTION
Semipermanent connection.
10581
PLUG-IN UNIT IS IN TEST
Plug-in unit is in test.
10582
MORE THAN 10 MATCHING RULES FOUND
There are more than 10 rules in an alarm system rulebase
which match the given parameters. Only the 10 first will be
handled.
10583
ILLEGAL INFORMATION FIELD NUMBER
The alarm number given does not have the information
field of the given number.
10584
ILLEGAL INFORMATION FIELD SUB NUMBER
The given information field of the given alarm number does
not have the sub field of the given number.
10585
DISK FILE VALIDITY CHECKINGS ARE BLOCKED
Disk file validity checkings are temporarily blocked.
10586
ASK FOR MORE ANALYSES
There are more analyses to be printed.
10587
ANALYSIS TREE CORRUPTED
Analysis tree is corrupted.
10588
ARF SUBSCRIBER
The subscriber number is in ARF use.
10589
VACANT ARF SUBSCRIBER NUMBER
The result of the subscriber number analysis is a vacant
number in ARF tree.
10590
ARF SUBSCRIBER NUMBER RESERVED
The subscriber number is used by an ARF subscriber.
Issue: 30-0
DN987378
319
Error messages
General Error Messages of System
10591
FILE IS IN STABLE STATE
File is in stable state i.e. values of the fields of the file are
stable.
10592
FILE IS IN UNSTABLE STATE
File is in unstable state i.e. values of the fields of the file
are unstable.
10593
ARF NAME DOES NOT EXIST
The ARF name defined is not found in the file.
10594
RSU NAME DOES NOT EXIST
The RSU name given is not found in the file.
10595
NO SENSE KEY
SCSI-command returns CHECK CONDITION status but in
sense data there is no specific sense key information to be
reported for the drive.
10596
BLANK CHECK
Blank tape or cassette.
10597
SCSI COMMAND ABORTED
SCSI-command aborted.
10598
ANALYSIS FOR ARF SUBSCRIBER DOES NOT EXIST
The subscriber number analysis for the ARF subscriber is
missing.
10599
INCOMPATIBLE SUBSCRIBER NUMBERS
The subscriber numbers given in the MML command are
incompatible with each other.
10600
TAPE MEDIUM ERROR
Physical end of tape (PEOT) or synthetic PEOT
encountered. Read or write error, probably caused by a
flaw in the tape or by a dirty head; replace the cassette or
the tape drive. End-of-data not found; drive tries to read a
blank or unformatted tape. Block sequence error; a format
discontinuity encountered. Positioning error during read.
Incompatible tape installed. Tape format corrupted. Tape
length error. Sequential positioning error. Repositioning
error. The last frame of the group not found when
appending new data during a write-type operation.
10601
320
TAPE DRIVE HARDWARE ERROR
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The cassette or the tape drive is faulty; replace the
cassette or the tape drive. Incompatible tape format.
Condensation detected.
10602
SOURCE DISK NOT OK
Loading cannot be executed because the source disk is
not OK.
10603
OBJECT STATE IS INCORRECT
The state of the object in the database is unsuitable for the
requestedoperation.
10604
ADDRESS IS NOT VALID MULTICAST ADDRESS
The first bit, i.e. the least significant bit of the first byte of
the address should be 1.
10605
ADDRESS LIST IS FULL
The address list of Ethernet MAC driver program is full.
10606
ADDRESS IS ALREADY IN LIST
The given multicast address was already in the address list
of the Ethernet driver program. The program does not
allow duplicate addresses.
10607
ADDRESS IS NOT FOUND IN ADDRESS LIST
The address could not be removed from the multicast
address list of theEthernet driver program because it was
not there.
10608
ET NOT IN SUPERVISION
ET unit is not in supervision due to the state of the ET.
10609
ILLEGAL SUPPORTING AMOUNT
Field Supporting amount of the message used for adding a
supporting rule has illegal value. No rule added.
10610
ALL RECORDS IN USE
All record reserved for certain kind of items are already in
use.
10611
RSS MODULEGROUP DOES NOT EXIST
The RSS module group number does not exist.
10612
SUB NOT FOUND
The subscriber module is not found.
10613
Issue: 30-0
SUBSCRIBER MODULE ALREADY EXISTS
DN987378
321
Error messages
General Error Messages of System
The subscriber module already exists.
10614
PCM NOT FOUND
PCM is not found.
10615
PCM ALREADY EXISTS
PCM already exists.
10616
ARRAY OVERFLOW
Array overflow; the array cannot hold all data to be written
there.
10617
BTS IS SHUTTING DOWN
Operation is not allowed while BTS is in state SHUTTING
DOWN (forced handover).
10618
CONTROL PARAMETERS NOT FOUND IN DATABASE
The control parameter set object has not been created into
the database.
10619
BCF APPLICATION FILE NOT FOUND
BCF application file is not found in the fixed disk of the
BSC.
10620
BCF MASTER FILE NOT FOUND
BCF master file is not found in the fixed disk of the BSC.
10621
BCF BUILD ID FAILURE
BCF build id is incorrect.
10622
BCF BUILD DIRECTORY NOT FOUND
BCF build directory is not found in the fixed disk of the
BSC.
10623
BCF ID ALREADY EXISTS IN BCF BUILD HANDLING
SYSTEM
BCF ID already exists in the BCF build handling system of
the BSC.
10624
BCF ID IS NOT FOUND IN BCF BUILD HANDLING
SYSTEM
BCF ID is not found in the BCF build handling system of
the BSC.
10625
322
BCF BUILD DIRECTORY IS ALREADY IN USE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
BCF build directory on the fixed disk of the BSC is already
in use.
10626
BCD BUILD ID ALREADY EXISTS
BCD build has already been created in the BCF package
handling system of the BSC.
10627
BCF BUILD ID IS NOT FOUND
BCF build id is not found in the package handling system
of the BSC.
10628
BCF BUILD IS ATTACHED TO BCF
BCF build is attached to the status of the BCF.
10629
BCF BUILD ID IS NOT ATTACHED TO BCF
BCF build id is not attached to the status of the BCF.
10630
BTMFIL READ ERROR
Error in reading the BTMFIL file.
10631
BTMFIL WRITE ERROR
Error in writing to the BTMFIL file.
10632
BTPFIL READ ERROR
Error in reading the BTPFIL file.
10633
BTPFIL WRITE ERROR
Error in writing to the BTPFIL file.
10634
BTMFIL FILE IS FULL
The BTMFIL file has no free records.
10635
BTMFIL FILE NOT SAVED TO DISK
The BTMFIL file is not saved to the fixed disk of the BSC.
10636
BTPFIL FILE IS FULL
The BTPFIL file has no free records.
10637
BTPFIL FILE NOT SAVED TO DISK
The BTPFIL file is not saved to the fixed disk of the BSC.
10638
BCF BUILD HANDLING SYSTEM BUSY (SWADMI
PROGRAM BLOCK)
The SWADMI program block cannot create a new hand.
10639
Issue: 30-0
BCF STATUS ALREADY HAS BUILD ATTACHMENT
DN987378
323
Error messages
General Error Messages of System
The BCF status already has a build attachment.
10640
BCF STATUS HAS NO BUILD ATTACHMENT
The BCF status has no build attachment.
10641
BCF BUILD STATUS IS INCORRECT
The BCF build status is incorrect.
10642
DEFAULT BCF BUILD IS NOT FOUND
The default BCF build is not found.
10643
SWADMI HAS RECEIVED NO RESPONSE FROM
REQMAN
The SWADMI program block has received no response
from the REQMAN program block.
10644
SWADMI HAS RECEIVED NO RESPONSE FROM
MEMDAT
The SWADMI program block has received no response
from the MEMDAT program block.
10645
NO FR TERMINALS IN USE
FR terminal freezing failed in FRU, because there are no
FR terminals in use.
10646
FR TERMINAL FREEZING FAILED PARTLY
Freezing of FR terminals in FRU failed partly.
10647
FR TERMINALS FREEZING FAILED COMPLETELY
Freezing of FR terminals in FRU failed completely.
10648
BCF BUILD ID ALREADY EXISTS
The BCF build has already been created in the BCF build
handling system of the BSC.
10649
FRAME RELAY SHORT PERIOD MEASUREMENT
ALREADY ACTIVE
An attempt has been made to start a FR short period
measurement which already is active.
10650
FRAME RELAY SHORT PERIOD MEASUREMENT
ACTIVE
The function fails because the FR short period
measurement is active.
10651
324
FRAME RELAY SHORT PERIOD MEASUREMENT DOES
NOT EXIST
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The functions fails because the FR short period
measurement identified does not exist.
10652
FRAME RELAY SHORT PERIOD MEASUREMENT NOT
ACTIVE
The function fails because the FR short period
measurement identified is not active.
10653
MEASUREMENT OBJECT DOES NOT EXIST
Creating a FR short period measurement failed because
one of the objects to be measured does not exist.
10654
MEASUREMENT NAME IS ALREADY USED
Creating the FR short period measurement failed because
the measurement name is already in use.
10655
NO FREE MEASUREMENT CONTROL DATA SLOTS
Creating the FR short period measurement failed because
file FSMCDA contains no free space for the control data of
the measurement.
10656
FRAME RELAY STATISTICS STOPPED
The operation failed because the FR statistics has been
stopped.
10657
USER ACCESS ALREADY EXISTS
Frame Relay user access already exists.
10658
USER ACCESS DOES NOT EXIST
Frame Relay user access does not exist.
10659
TRUNK ACCESS ALREADY EXISTS
Frame Relay trunk access already exists.
10660
TRUNK ACCESS DOES NOT EXIST
Frame Relay trunk access does not exist.
10661
VIRTUAL CONNECTION ALREADY EXISTS
Frame Relay virtual connection already exists.
10662
VIRTUAL CONNECTION DOES NOT EXIST
Frame Relay virtual connection does not exist.
10663
Issue: 30-0
DLC IS NOT CONFIGURED
DN987378
325
Error messages
General Error Messages of System
An attempt has been made to change the working state of
DPNSS circuit(s) from the NU-state up to some other state
by using the CEC-command, but the corresponding DLCs
(Data Link Connection) are not configured.
10664
BCF RESERVED FOR THE TEST
BCF is already reserved for the test.
10665
PRIMITIVE WAS NOT SENT
NMCOMM was not able to send the primitive due to the
malfunction of the OSI-stack.
10666
ERROR IN OPENING FILES IN PROGRAM BLOCK
FSHSTA
The operation failed because program block FSHSTA
could not open the files needed.
10667
CELL ID IS ILLEGAL OR INCOMPATIBLE
An attempt has been made to use illegal or incompatible
cell identification in radio network object creation.
10668
INCORRECT INDEX TO RSU ROUTES
The index of the RSU ROUTES is incorrect.
10669
30MIN DATA COLLECTION
Transferring of 30 minute measurement period meters
from the distributed part to the centralized part is in
progress.
10670
30MIN DATA COLLECTION COMPLETED
Transferring of 30 minute measurement period meters
from the distributed part to the centralized part has been
completed.
10671
NO METERS FOUND
No meters were found with the given parameters.
10672
STATISTICS STOPPED AND FILES NOT CREATED
Statistics files are not created because the statistics are
stopped.
10673
NO METERS DIVERGE FROM NIL
No meters diverging from nil have been found with the
given parameters.
10674
326
OMC WAS NOT UPDATED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The change which was made by a local MMI to the BSC
database was not updated to the OMC. There is no
working link to the OMC at the moment.
10675
BTS O&M LINK OUT OF ORDER
The BTS can not be updated because the O&M link is
down.
10676
BTS RECOVERY SYSTEM BUSY (PROGRAM BLOCK
BTLARM)
BTS reset acknowledgement message from BTLARM is
missing.
10678
FR USER DOES NOT EXIST
FR user does not exist.
10680
INCORRECT DATA BETWEEN D-CHANNEL FILES
One D-channel file contains incorrect data with regard to
other D-channel file. See alarm 2261 CONFLICT
BETWEEN TWO FILES.
10681
END OF ARRAY
An attempt has been made to write / read from an array
position, where there is no data.
10682
UNKNOWN CALL PARAMETER
An unknown call parameter was detected in the called
routine.
10683
ET FOR D-CHANNEL DOES NOT EXIST
There is no ET for the D-channel connection.
10684
DATA LINK CONNECTION ALREADY IN USE
The given data link connection value(s) are already in use.
10685
DATA LINK CONNECTION STATES CORRUPTED
The states of data link connection have been corrupted.
10686
DATA LINK CONNECTIONS ALREADY ACTIVATED
The given data link connection values are already
activated.
10687
DATA LINK CONNECTIONS ALREADY DEACTIVATED
The given data link connection values already deactivated.
10688
Issue: 30-0
DATA LINK CONNECTION NOT DEACTIVATED
DN987378
327
Error messages
General Error Messages of System
The data link connections are not deactivated.
10689
DATA LINK CONNECTIONS DO NOT EXIST
The given data link connection values do not exist.
10690
FIXED LIMITS EXCEEDED IN DATABASE SYSTEM
In the database system, a transaction has tried to exceed
the fixed limits (e.g. the number of elements of the search
structure). The transaction has been aborted.
10691
GT ANALYSIS NONEXISTENT
IMSI analysis has been created and type of address is
global title, but there exists no analysis for this global title.
10692
WSS NOT UPDATED
Data of WSS was not updated.
10693
QNG NOT UPDATED
Data of QNG was not updated.
10694
OPERATOR IDENTIFICATION NOT RESERVED
Operator identification has not been reserved.
10695
OPERATOR IDENTIFICATION RESERVED
Operator identification has been reserved.
10696
OPERATOR NOT LOGGED IN
Operator not LOGGED IN.
10697
OPERATOR NOT LOGGED OUT
Operator not LOGGED OUT.
10698
OPERATOR HAS SERVICEABILITY
Operator has serviceability.
10699
OPERATOR PLACE FREE
Operator place free.
10700
PRIORITY ALREADY USED
Priority already used.
10701
CALL TYPE ALREADY USED
Calltype already used.
10702
328
INCORRECT OPERATOR SYSTEM NUMBER
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Incorrect operator system number.
10703
INCORRECT STAGE NUMBER
Incorrect stage number.
10704
SERVICE HAS OPERATOR
Service has an operator.
10705
SERVICE NAME RESERVED
Service name reserved.
10706
TOO MANY OPERATORS
Too many operators.
10707
TOO MANY SERVICES
Too many services.
10708
TOO MANY SERVICE NUMBERS
Too many service numbers.
10709
SERVICE NUMBER NAME RESERVED
Service number name reserved.
10710
NUMBER RESERVED FOR SERVICE
Number reserved for service.
10711
NUMBER NOT RESERVED FOR SERVICE
Number not reserved for service.
10712
NONEXISTENT OPERATOR SYSTEM NUMBER
The operator system number does not exist.
10713
NONEXISTENT SERVICE
The service does not exist.
10714
NO SUCH SERVICE NUMBER NAME
There was no such service number name.
10715
NO SERVICE NUMBER
There was no such service number.
10716
NO OPERATORS
No operators.
10717
Issue: 30-0
RECEIVED EVENT DATA IS NOT OK
DN987378
329
Error messages
General Error Messages of System
Data received from the partner program block is out of
range.
10718
NO RESERVED RECORD IN THE FILE
The file has no reserved records when an attempt has
been made to search for a reserved record.
10719
CENTREX SERVICE NUMBER
The subscriber is a Centrex service number.
10720
DATABASE LOG BUFFER SIZE ERROR
Database log buffer size is erroneous, or there is an
unacceptable disagreement on the correct size. Automatic
recovery is executed to resolve the correct size and to
distribute it. However, if the error stays on or repeats itself,
then the log buffer size should be checked and fixed
manually to DBPARA files both on disks and in RAMmemory. Further, the computer units in question should be
restarted.
10721
CENTREX GROUP NONEXISTENT
There is no Centrex group.
10722
SUBNUMBER OF CENTREX GROUP VACANT
The subnumber of the Centrex group is vacant.
10723
SUBNUMBER OF CENTREX GROUP RESERVED
The subnumber is reserved for a member of a Centrex
group.
10724
MEMBER OF CENTREX GROUP WITH SUBNUMBER
The member of a Centrex group has a subnumber.
10725
MEMBER OF CENTREX GROUP WITHOUT
SUBNUMBER
The member of a Centrex group does not have a
subnumber.
10726
ERROR IN SEIZING TIME SLOT FOR SUBSCRIBER
Seizing of time slot for a subscriber in a subscriber module
did not succeed. All time slots for subscribers in the
subscriber module are currently reserved.
10727
330
OUTCALL IDENTIFIER CHANGE NOT POSSIBLE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
When a Centrex operator serves several Centrexes,
change of the outcall identifier of one single Centrex is not
possible, because the Centrex-groups must have the same
outcall identifier.
10728
ILLEGAL CHANNEL CONFIGURATION
An attempt was made to use unknown channel types, or
channel types in a TRX are incompatible.
10729
FREQUENCY ALREADY USED IN CELL
The frequency is already in use in the cell. It is not allowed
to create several transceivers using the same frequency
(ARFCN) in the cell.
10730
INCALL IDENTIFIER CHANGE NOT POSSIBLE
When a Centrex operator serves several Centrexes,
change of the incall identifier of single Centrex is not
possible because the Centrex groups must have the same
incall identifier.
10731
OUTCALL IDENTIFIER RESERVED
The value of the out-call identifier is reserved for a Centrex
in-call identifier, or for the first digits of sub-numbers of a
Centrex.
10732
INCALL IDENTIFIER RESERVED
The value of the in-call identifier is already reserved for a
Centrex out-call identifier, or for the first digits of subnumbers of a Centrex.
10733
FIRST DIGITS OF SUBNUMBER RESERVED
The value of the first digits of a subnumber is already
reserved for an outcall identifier, incall identifier, or another
Centrex group of the operator serving the Centrex in
question.
10734
NAME OF THE EXCHANGE EXISTENT
The name of the exchange exists.
10735
NAME OF THE EXCHANGE NONEXISTENT
The name of the exchange does not exist.
10736
STATISTICS NOT STARTED
Statistics have not been started.
10737
CHANGE OF NUMBER LENGTH NOT POSSIBLE
A change of the number length is not possible.
Issue: 30-0
DN987378
331
Error messages
General Error Messages of System
10738
SENDING OF DATA FAILED
Sending of data failed due to missing data messages.
10739
TOO MANY BLOCKS RESERVED FOR ACCESS GRANT
MESSAGES IN BTS
In the CCH configuration parameters of the BTS, too many
blocks have been reserved for Access Grant messages.
When a combined BCCH is used, the number of blocks for
Access Grant has to be reduced.
10740
REFRESHING OF A SUB DATABASE HAS FAILED
In a sub database, refreshing from the host database has
failed. Timeout may have occurred, or transactions from
the host database or those to sub database have failed.
10741
DATA ARE INCONSISTENT IN DATABASE SYSTEM
In the database system database inconsistency has been
found, e.g. the two-directional implementation of a relation
contains inconsistent data.
10742
ESCAPE CODE FAULTY
The given value differs from the stored value in the
PNEFIL file.
10743
NEW PNDFIL VARIANT NEEDED
There is no longer room to add a new full-size private
numbering index (PNI).
10744
PNDFIL REACHING MAXIMUM CAPACITY
The PNDFIL file variant where this private numbering
index (PNI) is stored is getting full.
10745
PNDFIL FULL
It is not possible to create this analysis because the
corresponding PNDFIL file variant is full.
10746
PNEFIL CORRUPTED
The contents of the PNEFIL file record are faulty.
10747
PNI ANALYSIS TREE CORRUPTED
The private numbering index analysis tree in the PNDFIL
file is faulty.
10748
DIGIT ANALYSIS TREE CORRUPTED
The private number analysis tree or long number digit
analysis tree in the PNDFIL file is faulty.
332
DN987378
Issue: 30-0
General Error Messages of System
10749
Error messages
PNRFIL CORRUPTED
The contents of the PNRFIL record are faulty.
10750
NONEXISTING PNI
There is no analysis for that private numbering index in the
PNI analysis tree.
10751
UNFINISHED BCF BUILD HANDLING OPERATION
EXISTS
There is an unfinished BCF build handling operation going
on in the BSC, and no new operation can be started.
10752
WSS AND QNG NOT UPDATED
Data of WSS and QNG were not updated.
10753
INVALID NUMBER OF ALTERNATIVE SUBDESTINATION
Number of the added alternative subdestination is invalid.
10754
POSITION NUMBER NOT RESERVED FOR OPERATOR
SERVICE POSITION
The position number has not been reserved for an
operator service position.
10755
ALL ALTERNATIVE SUBDESTINATIONS ALREADY
CREATED
An attempt has been made to create an alternative sub
destination although all alternatives have already been
reserved.
10756
SAVE SET MARK READ
The tabe block read was a delimiter of file groups (save set
mark).
10757
PHYSICAL CHANNEL CONNECTED TO ETHERNET
DATA TERMINAL
The physical channel is connected to an Ethernet data
terminal.
10758
ETHERNET DATA TERMINAL DOES NOT EXIST
The Ethernet data terminal is not found with the given
parameters (search key) in the OETFIL file.
10759
ETHERNET DATA TERMINAL ALREADY EXISTS
The Ethernet data terminal already exists in the OETFIL
file.
Issue: 30-0
DN987378
333
Error messages
General Error Messages of System
10760
UNLOCKED PHYSICAL CHANNEL CONNECTED TO
ETHERNET DATA TERMINAL
An unlocked physical channel is connected to an Ethernet
data terminal (physical channel is in UNLOCKED state).
10761
SOFTWARE PACKAGE DOWNLOAD TO BCF
INTERRUPTED
BTDOWN has failed in transferring a file segment from the
fixed disk of the BSC to the BTS.
10762
DEFAULT DOWNLOAD REQUEST SENT TO BCF
BTDOWN has failed in receiving build information from
SWADMI or in reading from the fixed disk of the BSC, and
has therefore sent a default download request to the BCF.
10763
NO MASTER FILE REQUEST RECEIVED FROM ABIPRB
BTDOWN has not received the master file request
transmitted from BTS by ABIPRB.
10764
NO APPLICATION FILE REQUEST RECEIVED FROM
ABIPRB
BTDOWN has not received an application file request
transmitted from the BTS by ABIPRB.
10765
ACKNOWLEDGE MESSAGE FROM ABIPRB MISSING
BTDOWN has sent a file record to the BTS and has not
received an acknowledge message transmitted from the
BTS by ABIPRB.
10766
NACK -MESSAGE RECEIVED FROM ABIPRB
BTDOWN has sent a file record message and received
NOT OK acknowledge message transmitted from the BTS
by ABIPRB.
10767
DOWNLOAD OPERATION NOT ALLOWED
BTDOWN is busy or, in the case of background download
operation, the BTS has no flash memory.
10768
NO FLASH MEMORY IN BTS
Downloading as a background operation is not allowed to
the BTS without flash memory.
10769
DOWNLOAD PROGRAM BLOCK (BTDOWN) BUSY
BTDOWN can not create new hands.
10770
334
DISK COPY ALREADY STARTED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The FSKDIS program block sends a message to the
FSSPRO program block informing the latter if disk copying
has already been started when FSKDIS receives a start
disk copying message.
10771
OPERATOR SERVICE HAS SERVICE NUMBER
Operator service has a service number.
10772
OPERATOR SERVICE HAS OPERATOR
Operator service has an operator.
10773
INCORRECT OUTCALL IDENTITY
Incorrect outcall identity.
10774
INCORRECT INCALL IDENTITY
Incorrect incall identity.
10775
INCORRECT FIRST DIGITS LENGTH
Incorrect length of the first digit.
10776
OPERATOR SERVICE ALREADY HAS SIMILAR FIRST
DIGITS
Operator service already has similar first digits.
10777
HOPPING BTS HAS INCORRECT STATE FOR
REQUESTED TASK
A Base Station with frequency hopping in use has an
operational state which is not suitable with the requested
task. Certain configuration changes in hopping cell are not
allowed when the BTS is in working state.
10778
BCF SW BUILD IS NOT IDENTICAL ON BOTH DISKS OF
BSC
The BCF software build contents are different on the disks
of the BSC.
10779
BCF BUILD IS THE DEFAULT PACKAGE
When the user tries to detach the default BCF build, this
message is printed.
10780
INCORRECT OPERATOR SERVICE TYPE
Incorrect operator service type.
10781
INCORRECT SUBSCRIBER CATEGORY
Incorrect subscriber category.
10782
Issue: 30-0
REPORT BUFFER FILE NOT FOUND
DN987378
335
Error messages
General Error Messages of System
Report buffer file (ring buffer) for the given buffer
identification is not found.
10783
CAN NOT CHANGE CALL TYPE
Can not change the call type.
10784
INCORRECT CALL TYPE
Incorrect call type.
10785
INCORRECT QUEUEING MODE
Incorrect queueing mode.
10786
THERE IS NO BCCH TRX UNDER CELL
The cell must have a transceiver (TRX) of the broadcast
control channel (BCCH or CPBCH).
10787
NO SERVICE NUMBER IDENTITY
There was no such service number identity.
10788
LOG_IN FUNCTION IS NOT ALLOWED
LOG_IN function is not allowed.
10789
INCOMPATIBLE OPERATOR APPLICATION TYPE
Incompatible operator application type.
10790
RESERVED CALLING CARD SUBSCRIBER NUMBER
The subscriber number is a reserved calling card
subscriber.
10791
RESERVED INDIRECT SUBSCRIBER NUMBER
The subscriber number is a reserved indirect subscriber
number.
10792
VACANT CALLING CARD SUBSCRIBER NUMBER
The number is a vacant calling card subscriber number.
10793
VACANT INDIRECT SUBSCRIBER NUMBER
The number is a vacant indirect subscriber number.
10794
CALLING CARD SUBSCRIBER
A calling card subscriber.
10795
INDIRECT SUBSCRIBER
Indirect subscriber number.
10796
336
ILMT BUSY
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The ILMT measurement device in SBCN/RSCN plug-in
unit is busy.
10797
ILMT FAULTY
The ILMT measurement device in SBCN/RSCN plug-in
unit is faulty.
10798
LOOPING TEST ERROR
Looping test error in the LIxxx plug-in unit.
10799
FDCBUF FILE SIZE TOO SHORT
The FSKDIS program block cannot create the records of
all FR users and FR trunk accesses at a time.
10800
SUBSCRIBER HAS ALSO A PARALLEL NUMBER IN
USE
The subscriber has another number in use, too; an old one
that will be erased after a period of time, and a new one.
10801
SUBSCRIBER NUMBER RESERVED HAS ALSO A
PARALLEL NUMBER IN USE
The subscriber number reserved has also another number
as a parallel number.
10802
RSU SUBSCRIBER HAS PARALLEL NUMBER IN USE
An RSU subscriber has also a parallel number in use.
10803
CHANGED SUBSCRIBER NUMBER HAS ALSO
PARALLEL ONE IN USE
A changed subscriber number has a parallel number as
well.
10804
DPABX SUBSCRIBER NUMBER HAS ALSO PARALLEL
NUMBER IN USE
A DPABX subscriber number has also a parallel number in
use for a period.
10805
ARF SUBSCRIBER HAS ALSO A PARALLEL NUMBER IN
USE
An ARF subscriber has also a parallel number in use.
10806
IDS SUBSCRIBER HAS A PARALLEL NUMBER IN USE
The identification subscriber (IDS) has a parallel number in
use.
10807
Issue: 30-0
CCS SUBSCRIBER HAS A PARALLEL NUMBER IN USE
DN987378
337
Error messages
General Error Messages of System
The calling card subscriber (CCS) has a parallel number in
use.
10808
PARALLEL SUBSCRIBER NUMBER RELEASED BUT
STILL IN PARALLEL MODE
The parallel subscriber number has been released but is
still under parallel modification.
10809
OSI ADDRESS IS ASSOCIATED TO PHYSICAL
CHANNEL GROUP
The OSI address has been associated with a physical
channel group.
10810
OSI CONNECTION REJECTED BY OSI STACK
Error coded returned by NMCOMM program block
because of rejection of an OSI connection.
10811
INCORRECT FIRST DIGITS
The first digits of the subnumber are incorrect.
10812
FIRST DIGITS CHANGE NOT POSSIBLE
When a Centrex operator serves several Centrexes,
change of the first digits of one single Centrex is not
possible.
10813
VXCN COMMUNICATION FAILURE
Communication failure between the VXCN and the OMU,
or the MUX, or between two program blocks in the VXCN.
10814
MOBILE ALLOCATION LIST OF FREQUENCY HOPPING
SYSTEM IS FULL
Attempts have been made to add too many TRXs to the
frequency hopping system.
10815
TOO FEW BLOCKS RESERVED FOR ACCESS GRANT
MESSAGES IN BTS
In the CCH configuration parameters of the BTS, too few
blocks have been reserved for Access Grant messages.
When a SDDCH/8 with CBCH is used, the number of
Access Grant blocks has to be added.
10816
NO CBCH CHANNEL FOR SMSCB USAGE IN CELL
There is no radio channel for SMSCB usage in the channel
configuration of the cell. A CBCH channel must be added
to the cell to perform SMSCB.
10817
338
TEST RADIO CHANNEL CANNOT BE ALLOCATED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
No radio channel in the TRX can be allocated for testing,
because they are all busy or locked by the user.
10818
SNPA ADDRESS IS ALREADY IN OSI ACCESS
CONTROL LIST (ACL)
The SNPA address is already in the OSI access control list
(in the OALFIL file - OSI access list file).
10819
SNPA ADDRESS IS NOT IN OSI ACCESS CONTROL
LIST (ACL)
The SNPA address is not in the OSI access control list (in
the OALFIL file - OSI access list file).
10821
FILE CREATION NOT ALLOWED
The creation of a file is not allowed.
10822
EVENT DATA IN BUFFER FILE
Because of a faulty connection to the OMC, the data of a
transmitted event notice ended up in a buffer file.
10823
EVENT BUFFER FILE IS FULL
The file used for buffering event notices is full, and old data
is being overwritten by incoming new notices.
10824
BSS-SYSTEM HAS NO RESOURCES FOR REQUESTED
TASK
The BSS-system is busy. It has not finished its previous
task, concerning the object. The unfinished task can be an
automatic recovery task or it can be the previous MMI task.
10825
NO SUCH DATABASE OCCURRENCE DEFINED IN
DBPARA
There is no such database occurrence defined for the
database in the DBPARA file.
10826
BCF SOFTWARE HANDLING CONFIRMATION
REQUIRED
There are some BCF software management commands
that need confirmation before the SWADMI program block
will execute the commands.
10827
MEASUREMENT ALREADY STARTED
The activation of the measurement has failed because it is
already in progress.
10828
MEASUREMENT NOT STARTED
The measurement has not been activated.
Issue: 30-0
DN987378
339
Error messages
General Error Messages of System
10829
MEASUREMENT NOT CREATED
The operation to be performed on the measurement has
failed because the measurement itself has not been
created.
10830
COMMUNICATION ERROR BETWEEN FSISTA AND
FSDSTA
There is a communication failure between the FSISTA and
FSDSTA program blocks.
10831
DLCI NUMBER NOT FOUND
The DLCI number is not found.
10832
MFST CHANNEL CLOSED AFTER SENDING ALL
BUFFERED CHARACTERS
The signalling channel of the MFST plug-in unit has been
closed, all buffered characters having been sent.
10833
DLCI ALREADY RESERVED
DLCI is already reserved.
10834
INCORRECT OPERATOR IDENTITY
The SFDATA database has an incorrect index to the
operator_data file.
10835
INCORRECT CENTREX SUBNUMBER
The number is not a subnumber of the CENTREX.
10836
ETHERNET DRIVER IS UNABLE TO SEND MAC
FRAMES
The Ethernet driver is out of resources.
10837
ORDINARY SERVICE NUMBER
The subscriber is an ordinary service number.
10838
ERROR IN READING PARAMETER FILE
The reading of the parameter file (PRFILE) has failed.
10839
ERROR IN DIGITAL SIGNAL PROCESSING
An error has occurred in the processing of the digital
measurement signal.
10840
CONFLICT BETWEEN INITIALISED AND REQUESTED
PCM NUMBER IN MFST
The requested PCM number is different from the initialised
PCM number in an MFST channel of an MFST plug-in unit.
340
DN987378
Issue: 30-0
General Error Messages of System
10841
Error messages
ATTEMPT TO CLOSE MFST CHANNEL OPENED BY
OTHER USER
The identification data of the user that tried to close an
MFST channel differ from those of the user that opened
the channel in question.
10842
OPERATOR TYPE MODIFICATION NOT ALLOWED
Operator type modification is not allowed.
10843
ANALYSIS OF CHARGING CONTINUES
The analysis of charging continues with the analysis of the
transmission medium requirement.
10844
TMR ANALYSIS OF CHARGING ALREADY EXISTS
The transmission medium requirement analysis of the
charging analysis already exists.
10845
TMR ANALYSIS OF CHARGING NONEXISTENT
There is no transmission medium requirement analysis of
charging.
10846
NOT LAST CHARGING
There are still transmission medium requirement analyses
of charging left.
10847
NO RESPONSE FROM SUB DATABASE HANDLING
PROGRAM BLOCK
A subdatabase handling program block does not answer.
Check the existence and working state of the computer
unit of the subdatabase.
10848
SUBSCRIBER HAS ALREADY MAXIMUM NUMBER OF
MEMBERSHIPS
The subscriber to be added into the hunting group is
already a member in the maximum number (8) of hunting
groups.
10849
UNLOCKED PHYSICAL CHANNEL IS ASSOCIATED TO
ISO IP PARAMETER SET
The ISO IP parameter set is associated to the physical
channel which is in the UNLOCKED state.
10850
PHYSICAL CHANNEL IS ASSOCIATED TO ISO IP
PARAMETER SET
The physical channel is associated to the ISO IP
parameter set.
Issue: 30-0
DN987378
341
Error messages
General Error Messages of System
10851
ISO IP PARAMETER SET DOES NOT EXIST
The given ISO IP parameter set is not found in the
OIPARA file.
10852
ISO IP PARAMETER SET ALREADY EXISTS
The ISO IP parameter set already exists.
10853
PDU TIMERS ARE NOT COMPATIBLE
PDU timers (parameters max_pdu_lifetime and ra_timer
fields in OIPARA file) are not compatible. See /ISO IP
Configuration Parameter Handling, Command Manual,
2.6/, parameters network_span and RA_timer.
10854
CHANNEL STATE ALREADY EXISTS
The channel state is not changed, because it already
exists.
10855
ALARM UNIT ADDRESS ALREADY EXISTS
An equipment with the given address already exists in the
service channel. All equipments in the same channel have
to have an address of their own.
10856
ALARM UNIT WITH GIVEN TYPE AND INDEX ALREADY
EXISTS
An equipment with the given alarm unit type and index
already exists. All equipments of the same type have to
have a unique index under the same BSC.
10857
CHANNEL DOES NOT EXIST
A service channel with the given channel number does not
exist.
10858
CHANNEL STATE IS ACTIVE
The service channel is active. Service channel activation
has to be denied before operation.
10859
CHANNEL CONTAINS EQUIPMENT
The service channel contains equipment. The equipment
has to be removed before operation.
10860
EQUIPMENT DOES NOT EXIST
Equipment with the given alarm unit type and index does
not exist.
10861
MAXIMUM NUMBER OF CHANNELS EXCEEDED
The maximum number of service channels has been
exceeded.
342
DN987378
Issue: 30-0
General Error Messages of System
10862
Error messages
MAXIMUM NUMBER OF EQUIPMENT EXCEEDED
The maximum number of equipment in the same service
channel has been exceeded.
10863
PCM-TSL ALREADY USED AS SERVICE CHANNEL
The given PCM-TSL is already used as a service channel.
10864
DATABASE IS INCONSISTENT ON ONE OR MORE
DISKS
This error code is used in situations where a database
copy on a disk is found to be inconsistent.
10865
MEMBER TYPE IS INCORRECT
A hunting group can have three kinds of members: an
ordinary member, a member of the hunting group, and a
member external to the exchange. The member type is
given in connection with the MML command. The error
situation occurs if e.g. an attempt is made to add an
ordinary member as a member of the hunting group.
10866
EXTENSION GROUP HAS ALREADY MAXIMUM COUNT
OF MEMBERS
The count of members in a hunting group is limited. If this
limit is exceeded, this error code is given.
10867
SUBSCRIBERS WITH DIFFERENT AREA CODE
The subscribers to be added in the same hunting group
must have the same area code. If this is not the case, this
error code is given.
10868
PVC INFORMATION IS NOT ALLOWED FOR A
PHYSICAL CHANNEL THRU ETHERNET TERMINAL
The user tries to attach X.25 PVC information to a channel
which provides ISO IP CNLS service.
10869
OOAFIL FILE READING FAILED
An attempt to read a single OOAFIL record failed.
10870
CONFLICT BETWEEN OAPFIL AND OOAFIL FILES
The OAPFIL and OOAFIL files contain contradictory
information.
10871
CONFLICT BETWEEN ACTIVE AND PASSIVE UNIT
OOAFIL FILE
The OOAFIL files of the active and passive units contain
contradictory information.
Issue: 30-0
DN987378
343
Error messages
General Error Messages of System
10872
APPLICATION PARAMETERS ALREADY EXIST
The application parameters already exist.
10873
ASWI UNIT IS NOT RESPONDING
The ATM Switching Unit is not currently responding.
10874
RESERVED FOR TESTING
The ATM virtual path/channel is currently involved in a
switch test.
10875
UNABLE TO CONNECT INCOMING VIRTUAL CHANNEL
Attempt to connect to the incoming virtual channel failed.
10876
UNABLE TO CONNECT OUTGOING VIRTUAL CHANNEL
The attempt to connect the outgoing virtual channel failed.
10877
UNABLE TO RELEASE INCOMING VIRTUAL CHANNEL
The attempt to release the incoming virtual channel of a
connection failed.
10878
UNABLE TO RELEASE OUTGOING VIRTUAL CHANNEL
The attempt to release the outgoing virtual channel of a
connection failed.
10879
ASWI UNIT IS LOCKED
The ATM Switching Unit is currently locked.
10880
ERRORS DETECTED ON CONNECTION
An ATM virtual connection is currently subject to error.
10881
ATM LINE DOES NOT EXIST
The ATM Line does not currently exist.
10882
ATM IN-LINE UNAVAILABLE
The incoming ATM line is currently unavailable.
10883
ATM OUT-LINE UNAVAILABLE
The outgoing ATM line is currently unavailable.
10884
VIRTUAL PATH DOES NOT EXIST
The virtual path does not exist.
10885
VIRTUAL CHANNEL DOES NOT EXIST
The virtual channel does not exist.
344
DN987378
Issue: 30-0
General Error Messages of System
10886
Error messages
INCOMING VPI UNAVAILABLE
The incoming VPI is currently unavailable.
10887
INCOMING VCI UNAVAILABLE
The incoming VCI is currently unavailable.
10888
OUTGOING VPI UNAVAILABLE
The outgoing VPI is currently unavailable.
10889
OUTGOING VCI UNAVAILABLE
The outgoing VCI is currently unavailable.
10890
NO FREE VIRTUAL PATH
No free virtual path.
10891
NO FREE VIRTUAL CHANNEL
No free virtual channel.
10892
NO FREE INCOMING VIRTUAL CHANNEL
No free incoming virtual channel.
10893
NO FREE OUTGOING VIRTUAL CHANNEL
No free outgoing virtual channel.
10894
REQUESTED ATM LINE NOT FREE
The requested ATM line is not free.
10895
REQUESTED VPI NOT FREE
The requested virtual path is not free.
10896
REQUESTED VCI NOT FREE
The requested virtual channel is not free.
10897
VIRTUAL PATH CONNECTION DOES NOT EXIST
The virtual path connection does not exist.
10898
VIRTUAL CHANNEL CONNECTION DOES NOT EXIST
The virtual channel connection does not exist.
10899
PARAMETERS ATTACHED TO APPLICATION TO BE
DELETED
The parameter block has been connected to an application
to be deleted.
10900
Issue: 30-0
FACILITY ALREADY IN THIS STATE
DN987378
345
Error messages
General Error Messages of System
The facility is already in this state.
10901
CREATION OF ATM LINE FAILED
The error code originates from the ATM Switching
database upon failure to create a new ATM line.
10902
VPI RESERVATION FAILED
The error code originates from the ATM Switching
database upon failure to create a new virtual path.
10903
VCI RESERVATION FAILED
The error code originates from the ATM Switching
database upon failure to create a new virtual channel.
10904
VIRTUAL PATH EXIST FOR LINE
The error code originates from the ATM Switching
database when an attempt is made to release an ATM line
with active virtual paths.
10905
VIRTUAL PATH CONNECTION EXISTS FOR VPI
The error code originates from the ATM Switching
database when an attempt is made to release a virtual
path used in an active connection.
10906
VIRTUAL CHANNEL EXISTS FOR VPI
The error code originates from the ATM Switching
database when an attempt is made to release a virtual
path which has an active virtual channel.
10907
VIRTUAL CHANNEL CONNECTION EXISTS FOR VCI
The error code originates from the ATM Switching
database when an attempt is made to release a virtual
channel which is used in an active connection.
10908
ATM LINE BLOCKED
The error code originates from the ATM Switching
database when an attempt is made to carry out a
disallowed transaction on an ATM line.
10909
VPI BLOCKED
The error code originates from the ATM Switching
database when an attempt is made to carry out a
disallowed transaction on a blocked VPI.
10910
346
VCI BLOCKED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The error code originates from the ATM Switching
database when an attempt is made to carry out a
disallowed transaction on a blocked VCI.
10911
ERROR IN SERVICE REQUEST
The error code originates from the ATM Switching service
upon detection of an invalid parameter in a service
request.
10912
CONGESTION IN ATM SWITCHING
The error code originates from the ATM Switching service
when there is congestion.
10913
NO RESPONSE FROM ASWMAN
Error code generated upon timeout of ASWMAN.
10914
FUNCTIONAL UNIT NOT LOCALLY SUPPORTED
The CMISE protocol functional units are not locally
supported.
10915
FUNCTIONAL UNIT NOT REMOTELY SUPPORTED
The CMISE protocol functional units are not remotely
supported.
10916
PROTOCOL VERSION NOT LOCALLY SUPPORTED
The CMISE protocol version is not locally supported.
10917
CMISE PROTOCOL VERSION NOR REMOTELY
SUPPORTED
The CMISE protocol version is not remotely supported.
10918
TERMINAL FUNCTION DOES NOT EXIST
The terminal function does not exist, or it has not been
taken into use.
10919
COMMUNICATION FAILURE BETWEEN AS7 AND
PROGRAM BLOCK
Communication failure between AS7 (PRLPGM) and a
program block.
10920
HUNTING GROUP IS A MEMBER OF ANOTHER
HUNTING GROUP
A hunting group can not be deleted if it is a member in
another hunting group.
10921
BTS BUSY
The BTS is busy. Try again later.
Issue: 30-0
DN987378
347
Error messages
General Error Messages of System
10922
INVALID MESSAGE
An invalid message.
10923
ERROR IN THE VALUE OF PARAMETERS
An error in the value of the parameters or data.
10924
MESSAGE OUT OF STATE
Message out of state.
10925
EXECUTION PROBLEM
Problems have been encountered in the execution of the
command.
10926
INVALID PARAMETER VALUE
Invalid parameter value.
10927
UNKNOWN OBJECT
Unknown object.
10928
OBJECT NOT ALLOWED
The object cannot be the target of a command/message.
10929
INVALID OBJECT STATE
The object state is not compatible with the transaction.
10930
UNIT IS NOT YET OPERATIONAL
The unit is not yet operational.
10931
SEQUENCE ERROR
A sequence error has occurred when transmitting a
segmented message.
10932
BTS IS NOT EQUIPPED WITH A FLASH MEMORY
The BTS is not equipped with a FLASH memory.
10933
BTS DOES NOT CONTAIN THE SPECIFIED DIVERSITY
THE BTS does not contain the specified diversity.
10934
BTS CANNOT BE INITIALIZED DUE TO LACK OF
CLOCKS
The BTS cannot be initialized because of lack of clocks.
10935
UNKNOWN UNIT IN CONFIGURATION MESSAGE
At least one unit is unknown in the configuration data
message.
348
DN987378
Issue: 30-0
General Error Messages of System
10936
Error messages
CONFIGURATION DATA UNIT CANNOT BE
CONFIGURED
At least one unit in the configuration message cannot be
configured.
10937
ONE OR MORE ELEMENTARY TESTS WERE NOT
PERFORMED
One or more elementary tests were not performed in the
TRX test.
10938
LACK OF RESOURCES
Lack of resources.
10939
HARDWARE FAILURE
Hardware failure.
10940
SOFTWARE PROBLEM
Software problem.
10941
RESERVATION OF VIRTUAL PATH CONNECTION
FAILED
This error code is generated when the ATM Switching
Database is unable to reserve a virtual path connection.
10942
RESERVATION OF VIRTUAL CHANNEL CONNECTION
FAILED
This error code is generated when the ATM Switching
Database is unable to reserve a virtual channel
connection.
10943
CONNECTION OF VIRTUAL CHANNEL CONNECTION
FAILED
This error code is generated when the ATM Switching
Database is unable to set a virtual channel connection to
the active state.
10944
CONNECTION OF VIRTUAL PATH CONNECTION
FAILED
This error code is generated when the ATM Switching
Database is unable to set a virtual path connection to the
active state.
10945
DISCONNECTION OF VIRTUAL PATH CONNECTION
FAILED
This error code is generated when the ATM Switching
Database is unable to change the state of an active virtual
path connection.
Issue: 30-0
DN987378
349
Error messages
General Error Messages of System
10946
DISCONNECTION OF VIRTUAL CHANNEL
CONNECTION FAILED
This error code is generated when the ATM Switching
Database is unable to change the state of an active virtual
channel connection.
10947
RELEASE OF VIRTUAL CHANNEL CONNECTION
FAILED
This error code is generated when the ATM Switching
Database is unable to release a reserved virtual channel
connection.
10948
RELEASE OF VIRTUAL PATH CONNECTION FAILED
This error code is generated when the ATM Switching
Database is unable to release a reserved virtual path
connection.
10949
WIRED ALARMS TEST IS NOT ALLOWED IN SPARE
UNIT
There was an attempt to start the wired alarms test in a
spare unit.
10950
INDIVIDUAL HUNTING NUMBER ALREADY EXISTS
A member of a hunting group can have individual hunting
in one group at a time, if there is an attempt to set the
facility in question in another group, this error code is
generated.
10951
STATISTICS ALREADY STARTED
The statistics function has already been started.
10952
QUEUEING FOR RESOURCES HAS BEEN STARTED
Queueing for resources has been started. They are
needed in a priority call.
10953
SUBSCRIBER IS NOT A MEMBER OF HUNTING
GROUP
This error code is generated when a subscriber is set
facilities that are available only to members of a hunting
group, or when inquiring about a group.
10954
SUBSCRIBER HAS NO INDIVIDUAL HUNTING
Call control inquires about a member of a hunting group for
whom individual hunting supposedly has been set, or an
MML command has been entered to delete individual
hunting from a member of a hunting group.
350
DN987378
Issue: 30-0
General Error Messages of System
10955
Error messages
FRCMAN REJECTED SEMIPERMANENT FILE
UPDATING
The updating of a semipermanent Frame Relay file has
been rejected by FRCMAN.
10956
SEMIPERMANENT FILE UPDATING REJECTED BY
FRDMAN
The updating of a semipermanent Frame Relay file has
been rejected by FRDMAN.
10957
DIGITS NOT STORED FOR NUMBER REPETITION
Digits have not been stored for number repetition.
10958
MCMD CHARGING TAPE AT THE BEGINNING OF TAPE
FILE
There was an attempt to write, onto an MCMD-format tape
file, charging data without the file header block, although
the tape was at the beginning of the file.
10959
MCMD-FORMAT CHARGING TAPE IS NOT AT THE
BEGINNING OF TAPE FILE
There was an attempt to write charging data, containing
file header info, to an MCMD-format charging tape,
although the tape is not at the beginning of the file.
10960
INCORRECT MODULE NAME IN MODULE HEADER
There is an incorrect module name in the header of a load
module.
10961
BTLARM HAS NOT ANSWERED BCF RESET OR BTS
CONFIGURATION REQUEST
The BSC Configuration Updating Program Block
(GUPDAT) has requested the BTS Alarm Handling and
Recovery Program Block (BTLARM) to reset BCF or to
configure BTS. No answer was received in time.
10962
PXADMI HAS NOT ANSWERED D-CHANNEL STATE
INQUIRY
The BSC Configuration Updating Program Block
(GUPDAT) has inquired about the D-channel state from the
PXADMI program block. No answer was received in time.
10963
Issue: 30-0
ABIPRB OR BTS SITE HAS NOT ANSWERED TRX
RESET OR STATE CHANGE REQUEST
DN987378
351
Error messages
General Error Messages of System
The BSC Configuration Updating Program Block
(GUPDAT) has requested the A-bis Interface Program
Block (ABIPRB) to reset TRX, or to change the TRX
administrative state on the BTS site via the BTS O&M link.
No answer received in time.
10964
MFC CHARACTER BUFFER FULL IN MFST PLUG-IN
UNIT
The MF signalling control program block has found that
there was an attempt to write MFC characters into a full
MFC character buffer.
10965
OFFSET OUT OF MODULE
An offset points outside of a module.
10966
INVALID RECORD SIZE
A files record size is invalid.
10967
INVALID MODULE IDENTIFICATION STRING
The identification string of a load module is invalid.
10968
MAFILE CORRESPONDING TO ENVIRONMENT NOT
FOUND
The MAFILE file corresponding to the environment of the
SW package is not found.
10969
MAFILE CORRESPONDING TO DELIVERY NOT FOUND
The MAFILE file corresponding to the SW delivery is not
found.
10970
MODULE CORRESPONDING TO MAFILE RECORD NOT
FOUND
The module corresponding to a record in the MAFILE file is
not found.
10971
MODULE NOT SYSTEM RELEASE DEPENDENT
A load module is not dependent on the system release
level.
10972
MODULE HAS INCORRECT VERSION
The version of a load module is incorrect.
10973
MODULE HAS INCORRECT ENVIRONMENT ID
The environment ID of a load module is incorrect.
10974
MODULE HAS INCORRECT DELIVERY NAME
The delivery name of a load module is incorrect.
352
DN987378
Issue: 30-0
General Error Messages of System
10975
Error messages
MODULE HAS INCORRECT DELIVERY VERSION
The delivery version of a load module is incorrect.
10976
SUBDATABASE UPDATE FAILED
Subdatabase transaction failed. The error code was written
into the logfile of the callers computer unit.
10977
LINE INTERFACE SOFTWARE VERSION UNSUITABLE
FOR TEST
The version of the subscriber interface software is not
suitable for the requested test.
10978
INCORRECT TEST STATE FOR THE OPERATION
The operation cannot be performed, as the state of the test
is wrong.
10979
TRUNK RESERVATION THRESHOLD TABLE OBJECT
NOT FOUND FROM RADIO NETWORK DATABASE
The Trunk Reservation decision threshold table has not
been created into the radio network database.
10980
TRUNK RESERVATION THRESHOLD TABLE IS IN USE
The Trunk Reservation decision threshold table is used by
a BTS. It cannot be deleted before the BTS using it is
detached.
10981
DATABASE SYSTEM CONTAINS A FILE WITH ZERO
LENGTH
There is a file with zero length in the database system.
10982
WRITING TO LOG FILE WHILE READING
The FR User Event Log File (FUELOG) is being written
into at the time of reading.
10983
LOG EVENTS NOT FOUND
Log events are not found in the FR User Event Log File
(FUELOG).
10985
TEST INTERRUPTED
Execution of the tests has been interrupted.
10986
TMRANA RECORD NONEXISTENT
The Transmission Medium Requirement Analysis file
(TMRANA) record does not exist.
10987
Issue: 30-0
ET UNIT WITH D-CHANNEL DID NOT ANSWER
DN987378
353
Error messages
General Error Messages of System
An exchange terminal unit with a D-channel has failed to
respond within time supervision.
10988
AON CHARACTER NOT RECEIVED
No AON character has been received after the MFST
channel was opened.
10989
AON RECEIVING ERROR
The error was in AON receiving.
10990
MODULE UPDATE FAILED
The updating of the information in the subscriber module
failed.
10991
THE FILE IS SYSTEM RELEASE DEPENDENT AND
CANNOT BE CREATED IN THE EXCHANGE
The file cannot be created in the exchange, it is part of the
software delivery.
10992
FR USER ACCESS IS USED BY VIRTUAL CONNECTION
A Frame Relay user access is used by a virtual
connection.
10993
FR TRUNK ACCESS IS USED BY VIRTUAL
CONNECTION
A Frame Relay trunk access is used by a virtual
connection.
10994
FR TRUNK ACCESS NOT PASSIVATED
A Frame Relay trunk access has not been passivated.
10995
FR VIRTUAL CONNECTION NOT PASSIVATED
A Frame Relay virtual connection has not been passivated.
10996
PROGRAM BLOCK COMMUNICATION FAILURE
There is a communication failure between program blocks.
The program blocks concerned are specified in the
PROGRAM BLOCK COMMUNICATION ERROR alarm
that is set simultaneously.
10997
OMOLIB SEARCH FAILED
The requested object was not found by the Q3 Object
Model Library (OMOLIB).
10998
OMOLIB OBJECT DOES NOT EXIST
The requested object does not exist.
354
DN987378
Issue: 30-0
General Error Messages of System
10999
Error messages
OMOLIB FINDS NO VALUE FOR OBJECT
No value found for the requested object by the Q3 Object
Model Library (OMOLIB).
11000
OMOLIB ROUTINE NOT DEFINED FOR OBJECT
No library routine was defined for the requested object.
11001
ILLEGAL HANDLE TO INTERNAL POSITION NUMBER
ARGUMENT TABLE
An MML program tries to read a non-existent internal
position number argument table.
11002
BCCH ALLOCATION FREQUENCY LIST WAS NOT
FOUND FROM THE DATABASE
The BCCH allocation frequency list has not been created
into the radio network database.
11003
BCCH ALLOCATION FREQUENCY LIST IS STILL USED
BY SOME BTS
The BCCH allocation frequency list cannot be deleted, if a
BTS is still using it.
11004
BCCH ALLOCATION FREQUENCY LIST IS FULL
No more frequencies can be added to the BCCH allocation
frequency list.
11005
BTS IS NOT EQUIPPED WITH STM
A BTS is not equipped with a STM.
11006
COMMUNICATION FAILURE BETWEEN BTS OMU AND
STM
A communication failure has occurred between a BTS
OMU and a STM.
11007
STM CARRIER SETTING FAILED
The setting of a STM carrier wave has failed.
11008
STM BCCH SYNCHRONISATION FAILED
The synchronisation of a STM to a given BCCH channel
has failed.
11009
INVALID BCCH FREQUENCY WAS GIVEN BY BSC TO
BTS
An invalid BCCH frequency was given by the BSC to a
BTS.
11010
Issue: 30-0
UNSPECIFIED ERROR DURING STM OPERATION
DN987378
355
Error messages
General Error Messages of System
An unspecified error has occurred during a STM-related
operation.
11011
NO CALL REPORT IS AVAILABLE FROM STM
There is no call report available from the STM.
11012
TEST INTERRUPTED BY USER
The user has interrupted a test.
11013
UNKNOWN LOGICAL ADDRESS OF TRANSMISSION
EQUIPMENT SENT BY BSC
The logical address of an unknown transmission
equipment was sent by the BSC.
11014
COMMUNICATION FAILURE BETWEEN BTS OMU AND
TRANSMISSION EQUIPMENT
There was a communication failure between the BTS OMU
and the transmission equipment.
11015
INVALID TEST PARAMETERS
Invalid test parameters.
11016
METERS INQUIRY BUSY
The interrogation of the meters is in progress.
11017
UNSPECIFIED ERROR OCCURED DURING
SCHEDULED TESTING
An unspecified error occured during scheduled testing in
the BSC.
11018
UNSPECIFIED ERROR OCCURED DURING TEST
An unspecified error occured during a test.
11019
NO TEST GOING ON IN CONCERNED BCF
There is no test going on in the BCF in question.
11020
TMGMAN IS BUSY WITH ANOTHER TREHAN MML
SESSION
The starting of a TREHAN MML session was rejected
because TMGMAN is already engaged in another session.
11021
MUX SIGNALLING INCOMPATIBLE FOR
MEASUREMENT
The MUX signalling does not recognise subscriber
measurements.
11022
356
PCM-TSL RESERVED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The PCM-TSL is already reserved.
11023
POSITION ID NOT FOUND
The position ID does not exist.
11024
INVALID FILTER VALUE IN CMISE PRIMITIVE
The OCEAPI library returns this error code if the filter value
given by the user of the library is invalid.
11025
INVALID SCOPE VALUE IN CMISE PRIMITIVE
The OCEAPI library returns this error code if the scope
value given by the user of the library is invalid.
11026
GROUP LOGGING NOT ACTIVATED
Group logging has not been activated by the MML
program.
11027
NOT DAS POSITION
The position is not a DAS position.
11028
DAS ID RESERVED
The DAS identity is reserved.
11029
INCORRECT CALL RETURN NUMBER
Incorrect call return number.
11030
INTERNAL SERVICE NUMBER
Internal service number.
11031
NOT DA SERVICE NUMBER
Not a DA (IBM/DAS) service number.
11032
BCF BUILD EXISTS ON BSC DISK
BCF build already exists in the BCF build handling system
of the BSC and in the fixed disk of the BSC.
11033
EMPTY BCF BUILD SUBDIRECTORY NOT FOUND
Empty BCF build directory is not found on the fixed disk of
the BSC.
11034
SUBDATABASE AND MODULE UPDATES BOTH FAILED
The changes could not be updated into the subdatabase.
Also the updating of subscriber module information failed.
11035
NO WAKE-UP ORDERS
There are no active wake-up orders.
Issue: 30-0
DN987378
357
Error messages
General Error Messages of System
11036
NO SUCCESSFUL WAKE-UP CALLS
No successful wake-up calls were found.
11037
INCORRECT ROUTINE TEST PARAMETER
A routine test parameter is found to be incorrect.
11038
DISK UPDATE OF RTPARA IN PROGRESS
It is not possible to modify the routine test parameters in
the RTPARA file as the previous modification has not yet
been updated to disk.
11039
INCORRECT ROUTINE TEST TYPE
The given routine test type is incorrect.
11040
INVALID JUMPER GROUP
The jumper group given in the jumper group parameter
has not been defined in the JVALUE file.
11041
FAILURE TO GENERATE ROUTINE TEST REPORT
Generating a routine test report has failed because of a
failure in the routine test software.
11042
OUTPUT OF ROUTINE TEST REPORT FAILED
The outputting of the routine test report has failed
completely.
11043
OUTPUT OF ROUTINE TEST REPORT FAILED
PARTIALLY
The outputting of the routine test report has failed on some
of the predefined devices.
11044
CONFLICT BETWEEN PARAMETERS OF OWN CELL
AND ADJACENT CELL
When creating or modifying an adjacent cell, the
parameters are in conflict with the parameters of own cell.
11045
LDIG INVALID
LDIG Analysis invalid (LDIG = long digit).
11046
SDIG INVALID
The given SDIG (short digit) is invalid.
11047
SDIG AND LDIG INVALID
Both the given SDIG (short digit) and the given LDIG (long
digit) are invalid.
358
DN987378
Issue: 30-0
General Error Messages of System
11048
Error messages
ERRONEOUS COUNTRY CODE
The country code given does not match with the one in the
HRNFIL file.
11049
RANGE GIVEN OVERFLOWS HRNFIL MAXIMUM
Range given causes the total numbers of a given type of
range to exceed the maximum.
11050
RANGE GIVEN OVERLAPS WITH ANOTHER
Range given overlaps with a range previously defined.
11051
ERROR READING PRFILE
Error reading PRIFLE.
11052
NO TEST EQUIPMENT DEFINED FOR BCF IN
QUESTION
There is no test equipment defined in the database of the
BSC for the BCF for the test to be started.
11053
INVALID TEST EQUIPMENT DEFINED FOR TEST IN
QUESTION
The test equipment defined for the BCF and for the test in
question is invalid.
11054
PLUG-IN UNIT TYPE OF JUMPER DOES NOT MATCH
INTERFACE TYPE
The plug-in unit type in the jumper group record (file
JVALUE) does not correspond to the plug-in unit type of
the subscriber line interface.
11055
ERROR IN SETTING PROTECTION
This error code is sent when setting the 2 Mbit/s protection
failed.
11056
ETHERNET TERMINAL NOT FOUND FROM OETFIL
An Ethernet terminal device, found in OPCFIL, is not found
in OETFIL.
11057
TIME IS UNDEFINED
The last freezing and the last disk copying are not carried
out, or the next disk copying has not been defined.
11058
DISTRIBUTED PART COUNTERS FREEZING IN
PROGRESS
The freezing of the counters of the distributed part is in
progress.
Issue: 30-0
DN987378
359
Error messages
General Error Messages of System
11059
DATA COLLECTION AFTER FRU CHANGE IS IN
PROGRESS
Data collection from the changed FRU unit is in progress.
11060
DISK COPYING IS IN STOPPED STATE
Disk copying is in the STOPPED state.
11061
NO SUCH TP INSTANCE
The given termination point does not exist.
11062
NO SUCH GTP INSTANCE
The given group termination point does not exist.
11063
NO SUCH TPPOOL INSTANCE
The given termination point pool does not exist.
11064
NO TP IN TPPOOL
There is no free termination point in the termination point
pool.
11065
PART OF GTP
The given termination point is part of a group termination
point.
11066
MEMBER OF TPPOOL
The given termination point is part of a termination point
pool.
11067
INCORRECT TP
The given termination point is not correct.
11068
INCORRECT GTP
The given group termination point is not correct.
11069
CIC RESERVED
The PCM circuit has already been defined for another
destination point.
11070
CIC ALREADY IN USE
The CIC is already in use.
11071
TASK SENT TO PASSIVE UNIT
A task request was sent to the passive unit. This error is
possible in a unit switchover. Try to send the task request
again after a while.
360
DN987378
Issue: 30-0
General Error Messages of System
11072
Error messages
STATUS CHANGED TO DEFAULT BUILD, BUT
ACTIVATION FAILED
The default build in BCF has been changed, but
downloading to BCF was unsuccessful.
11073
NO RESPONSE FROM RSAI
A program block on the RSAI unit has failed to
acknowledge a message within the time supervision
period.
11074
START AND END TIMES OF ROUTINE TESTING ARE
TOO CLOSE
The starting and finishing times of routine testing are
defined too near each other. The daily (busy or idle) time
for routine testing is too short. The difference between the
starting and finishing time must be at least one hour.
11075
FR NODE DOES NOT EXIST
The Frame Relay node does not exist.
11076
FR NODE ALREADY EXISTS
The Frame Relay node already exists.
11077
GIVEN TEST OBJECT DOES NOT EXIST
The given test object does not exist in the exchange
configuration.
11078
DIFFERENCE BETWEEN TRANSACTION CHECKSUMS
IN WO AND SP
The check sums of the updates of a database transaction
differ in WO from those in SP.
11079
WIRED ALARM TEST BUSY
The wired alarm test is busy. Try again after a little while.
11080
PROCESS NOT IN NORMAL WORKING STATE
A process is not in a normal working state. The working
state of the unit is such that the process is unable to
function in it (or the process has remained in a wrong
state).
11081
FLASH MEMORY IS FULL
Old data is updated and new data is inserted, but FLAMAN
is no longer able to handle the FLASH memory correctly.
Eventually, FLAMAN will reject all updating and inserting
requests, as the FLASH memory runs out of space. This
Issue: 30-0
DN987378
361
Error messages
General Error Messages of System
error code is a warning and means that FLAMAN can still
serve for a while, but soon FLAMAN will no longer be able
to write into the FLASH memory.
11082
OPERATION PREVENTED IN SPLIT UNIT
A function has been prevented from being carried out in a
split unit.
11083
OPERATION PREVENTED IN TRIAL CONFIGURATION
A function has been prevented from being carried out in
the trial configuration.
11084
BSIC VALUE OF ADJACENT CELL DIFFERS FROM
CORRESPONDING OWN CELL VALUE
This error code is produced when an adjacent cell is
created or modified whose given BSIC differs from the
BSIC of the own cell.
11085
PARAMETER MS_TXPWR_MAX_CELL OF ADJACENT
CELL DIFFERS FROM CORRESPONDING OWN CELL
VALUE
The ms_txpwr_max_cell parameter value given to an
adjacent cell to be created or modified differs from that of
the own cell.
11086
CELL_TYPE PARAMETER VALUE OF ADJACENT CELL
DIFFERS FROM CORRESPONDING OWN CELL VALUE
The value of the cell_type parameter of an adjacent cell to
be created or modified is different from that parameter
value in the own cell.
11087
VALUE OF PARAMETER BCCH_FREQ OF ADJACENT
CELL DIFFERS FROM CORRESPONDING OWN CELL
When creating or modifying an adjacent cell, the given
bcch_frequency value differs from that of the own cell.
11088
ALARM NOT FOUND IN BTRFIL
An alarm number is not found in BTRFIL.
11089
BLOCKED ALARMS NOT FOUND IN BTRFIL
Alarm numbers in blocked state are not found in the
BTRFIL file.
11090
ALARM NOT FOUND IN ALARM HISTORY
An alarm is not found in the alarm history.
11091
362
ALARM NOT FOUND IN RING BUFFER FILE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
An alarm is not found in the ring buffer file.
11092
WAITING FOR 500 HZ SIGNAL STOPPED BECAUSE OF
TIME OUT
The 500 Hz input signal was not found during the time
supervision period.
11093
WAITING FOR 425 HZ SIGNAL STOPPED BECAUSE OF
TIME OUT
The 425 Hz input signal was not found during the time
supervision period.
11094
SERVICE PROFILE IS ALREADY ATTACHED TO OSI
APPLICATION
The service profile has already been attached to the OSI
application.
11095
SERVICE PROFILE ATTACHED TO APPLICATION TO
BE DELETED
A service profile is attached to the application that is to be
deleted.
11096
NO SERVICE PROFILE ATTACHED TO OSI
APPLICATION
No service profile has been attached to the given OSI
application. The service profile has to be found in the
OOAFIL file.
11097
UNDER A BCF ALL HSN:S OF BTS:S MUST BE 0 OR
OTHER THAN 0
Hopping can be defined to be cyclic (HSN=0) or random
(HSN other than 0). Cyclic and random hopping cannot be
defined simultaneously under a BCF.
11098
PXNETM HAS NOT ANSWERED D-CHANNEL STATE
INQUIRY
GUPDAT has inquired about the state of the D-channel
from the PXNETM program block. No answer was
received in time.
11099
NO ANSWER RECEIVED FOR TEST STOPPING
REQUEST
IS1MAS has requested, unsuccessfully, ISHDRV to stop
the ISDN line test.
11100
D-CHANNEL IS BLOCKED
The D-channel is blocked because of a fault by the system
or the user.
Issue: 30-0
DN987378
363
Error messages
General Error Messages of System
11101
ISDN SUBSCRIBER LINE ACTIVATION FAILURE
The activation failed because the line or the interface is
faulty.
11102
NO ANSWER RECEIVED TO TEST LOOP CONNECTION
REQUEST
The ISDN subscriber line is not looped because the line or
the interface is faulty.
11103
CALL DISCONNECTION FAILED
The disconnection of a call failed because the calls priority
was higher than the tests.
11104
D-CHANNEL TEST HAS FOUND DATA ERROR
Bit errors were found from the D-channel, the D-channel is
faulty.
11105
TEST ABORTED BECAUSE OF PREVIOUS
DEACTIVATION
A test has been aborted before the time limit exceeded
and the test result is incorrect. The previous deactivation
may have been e.g. an incoming call.
11106
READING OF BIT ERROR COUNTERS FAILED
The reading of the bit error counters was unsuccessful
because the transmission circuit did not answer.
11107
COMMUNICATION FAILURE BETWEEN MODULE
CONTROLLER AND LINE INTERFACE PLUG-IN UNIT
Communication has failed between a module controller
(SBCN/RSCN/etc.) and a line interface plug-in unit (LID5
etc.) because the time limit was exceeded, or the
transmitting program did not answer.
11108
B-CHANNEL TEST HAS FOUND DATA ERROR
Bit errors were found in the B-channel, the B-channel is
faulty.
11109
SCSI ADDRESS ALREADY EXISTS
There has been an attempt to add an SCSI device to an
already reserved bus address.
11110
AD&C SUBSCRIBER
The subscriber type is AD&C.
11111
REMINDER CALL SUBSCRIBER WITH CHARGING
A reminder call subscriber who has charging.
364
DN987378
Issue: 30-0
General Error Messages of System
11112
Error messages
REMINDER CALL SUBSCRIBER WITH NO CHARGING
A reminder call subscriber who has no charging.
11113
AD&C SUBSCRIBER NUMBER IS VACANT
AD&C subscriber number is vacant.
11114
AD&C SUBSCRIBER NUMBER RESERVED
AD&C subscriber number is reserved.
11115
REMINDER CALL SUBSCRIBER NUMBER WITH
CHARGING IS VACANT
A reminder call subscriber number which has charging is
vacant.
11116
REMINDER CALL SUBSCRIBER WITH CHARGING IS
RESERVED
A reminder call subscriber who has charging is reserved.
11117
REMINDER CALL SUBSCRIBER WITH NO CHARGING
IS VACANT
A reminder call subscriber with charging is vacant.
11118
REMINDER SUBSCRIBER WITH NO CHARGING IS
RESERVED
A reminder call subscriber with no charging is reserved.
11119
PARALLEL AD&C SUBSCRIBER
The AD&C subscriber is a parallel one.
11120
PARALLEL REMINDER CALL SUBSCRIBER WITH
CHARGING
A parallel reminder call subscriber who has charging.
11121
PARALLEL REMINDER CALL SUBSRIBER WITH NO
CHARGING
A parallel reminder call subscriber who has no charging.
11122
BTS NAME ALREADY IN USE OR ILLEGAL
A BTS name must be unique in the BSC. It may consist of
allowed characters only.
11123
INCORRECT DEFAULT SERVICE NUMBER
Incorrect operators default service number.
11124
Issue: 30-0
TSC (TRX) AND BCC (BTS) VALUES MUST BE EQUAL
UNDER BCF
DN987378
365
Error messages
General Error Messages of System
The Training Sequence Codes of the TRXs and the BTS
Colour Codes of the BTSs must be equal under the BCF.
11125
NO SERVICE PROFILE HAS BEEN ATTACHED TO OSI
APPLICATION
There is no service profile attached to the given OSI
application.
11126
CONFLICT BETWEEN GIVEN AND ATTACHED OSI
APPLICATION SERVICE PROFILE
There is a conflict between the given service profile type
and the service profile type attached to the OSI
application, e.g. the OSI application is a Q3 application
(CMISE) and the user is modifying the VT mode: the
parameters are mutually exclusive.
11127
TIMESLOT OF ET IS ALREADY USED BY ANOTHER
RADIO CHANNEL
There has been an attempt to use a timeslot which is
already used by another radio channel.
11128
SIGNALLING UNIT IS FULL, NO MORE TRANSCEIVERS
CAN BE CREATED IN SAME UNIT
The maximum number of transceivers allowed in the
signalling unit has been reached. A D-channel in another
signalling unit should be used.
11129
D-CHANNEL IS ON DIFFERENT PCM THAN RADIO
TIME SLOTS
The radio time slots of a TRX must be created on the ETPCM that contains the D-channel.
11130
DEFAULT SERVICE NUMBER IS IN USE
The default service number cannot be removed if an
operator is using it.
11131
OMOLIB MEMORY MANAGEMENT ERROR
OMOLIB did not find the memory management data
structure registered for the current process.
11132
PREPROCESSOR LOADING IN PROGRESS
The loading of the preprocessor unit is in progress.
11133
PREPROCESSOR LOADING TIME OUT
The total time supervision of the loading of the
preprocessor unit has expired.
11134
366
PREPROCESSOR LOADING FAILURE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The loading of the preprocessor failed.
11135
GIVEN UNIT IS NOT IN ACTIVE STATE
The given unit is not in the active state. The user can
create an OSI application only for an active unit.
11136
CREATION OF BROADBAND FR ACCESS FAILED
This error code is generated by FBBASE upon an
unsuccessful attempt to create a new FR access.
11137
NO FREE DLCI AVAILABLE
Occurs when an attempt is made to reserve a virtual
channel from the FBBASE for an access in which all the
DLCI values are currently in use.
11138
NO FREE ACCESS IDENTIFIER
Occurs when an attempt is made to reserve an access
identifier from FBBASE.
11139
ATM TRUNK ACCESS DOES NOT EXIST
This code is generated in response to an ATM trunk
related request for which an access does not exist.
11140
ATM VIRTUAL CHANNEL EXISTS
Indicates that a certain ATM virtual channel already exists.
11141
ATM VIRTUAL CHANNEL DOES NOT EXIST
Indicates that a certain ATM virtual channel does not exist.
11142
BROADBAND ROUTE DOES NOT EXIST
This code is generated in response to requests relating to
routes that do not exist.
11143
BROADBAND FRAME RELAY ROUTE UNAVAILABLE
This code is generated in response to requests relating to
unavailable routes.
11144
VIRTUAL PATH EXISTS FOR ACCESS
This error code indicates that there remains at least one
reserved ATM virtual path for an access.
11145
ATM ROUTE STILL EXISTS FOR THE DLCI
This code is generated when an attempt is made to
release a DLCI for which there remains at least one
reserved ATM route.
11146
Issue: 30-0
ATM TRUNK ACCESS NOT DEACTIVATED
DN987378
367
Error messages
General Error Messages of System
An ATM trunk access has not been deactivated.
11147
ATM TRUNK ACCESS NOT ACTIVATED
An ATM trunk access has not been activated.
11148
FRAME RELAY TRUNK ACCESS NOT ACTIVATED
A Frame Relay trunk access has not been activated.
11149
ATM TRUNK ACCESS IS USED BY VIRTUAL
CONNECTION
A virtual connection exists for the ATM trunk access.
11150
DIGITS NOT STORED FOR CALL BACK
If no call has been received whose subscriber number was
stored, or the identity of subscriber A is incomplete, this
error code is used.
11152
NUMBER OF FRAME UNITS IS NOT CONSISTENT
WITH BTS DATABASE
Number of FUs in the configuration message is not
consistent with the BTS HW database.
11153
DATABASE DOES NOT EXIST IN BTS
A BTS does not have an HW database.
11154
NUMBER OF CARRIER UNITS IS NOT CONSISTENT
WITH BTS DATABASE
The number of carrier units in the configuration message is
not consistent with the BTS HW database.
11155
DATABASE HAS BEEN CREATED WITH OLD MMI
VERSION
A BTS HW database has been created using an old
version of the OMU MMI.
11156
MESSAGE CONTAINS INVALID OBJECT TYPE
The message contains an invalid object type.
11157
NO RESPONSE FROM BTS WITHIN TIME LIMIT
A BTS does not respond within time limit.
11158
NEGATIVE ACKNOWLEDGEMENT FROM BTS
A BTS has sent a negative acknowledgement to the BSC.
11159
PREVIOUS BTS CONFIGURATION IN PROGRESS
The previous configuration of a BTS is still in progress.
368
DN987378
Issue: 30-0
General Error Messages of System
11160
Error messages
CONFIGURATION DID NOT END DURING TIME
SUPERVISION
The BSC did not receive the conf_completed message
within time supervision.
11161
BTL IS BUSY DUE TO PREVIOUS RECOVERY ACTION
BTLARM is busy due to a previous recovery action.
11162
NUMBER OF COMMON DIGITS IS NOT THE SAME
The amount of common digits in the global and MSN
number is not the same.
11163
BCF SOFTWARE DOWNLOAD MAXIMUM TIME
EXPIRED
The maximum time defined for the BCF software download
has expired.
11164
BCF HAS NOT REQUESTED CONFIGURATION DATA
WITHIN DEFINED TIME LIMIT
A BCF has not requested a configuration within the defined
time limit from the BSC after the SW download.
11165
RADIO NETWORK CONFIGURATION MANAGEMENT
ACKNOWLEDGEMENT TIME-OUT
The radio network configuration management (the
GUPDAT program block) has not sent an
acknowledgement message within the defined time limit.
11166
BTS O&M LINK HAS NOT BEEN ESTABLISHED WITHIN
DEFINED TIME LIMIT
The BTS recovery system in the BSC has not been
informed about the establishment of the BTS O&M link (to
working state) within the defined time limit.
11167
BTS OMU HAS NOT BEEN STARTED WITHIN DEFINED
TIME LIMIT
The BTS OMU has not sent the BTS_OMU_STARTED_S
message (1252) to the BSC within the defined time limit.
11168
COPYING CLASS DOES NOT EXIST
A Frame Relay meters disk-copying class does not exist.
11169
COPYING CLASS IS USED FOR WEEKDAYS OR
SPECIAL DAYS
A Frame Relay meters disk-copying class is used for
weekdays or for special days.
Issue: 30-0
DN987378
369
Error messages
General Error Messages of System
11170
SPECIAL DAY DOES NOT EXIST
A Frame Relay meters disk-copying special day does not
exist.
11171
SPECIAL DAY EXISTS
A Frame Relay meters disk-copying special day already
exists.
11172
METER GROUP DOES NOT EXIST
A Frame Relay disk-copying meter group does not exist.
11173
METER GROUP ALREADY EXISTS
The Frame Relay meters disk-copying meter group already
exists.
11174
METER DOES NOT EXIST
A meter does not exist in the Frame Relay meters diskcopying meter group.
11175
METER ALREADY EXISTS
A meter already exists in the Frame Relay meters diskcopying meter group.
11176
USER ACCESS ASSOCIATED WITH METER GROUP
A Frame Relay user access is associated with a Frame
Relay meters disk-copying meter group.
11177
FR METER GROUP NAME CONFLICT
There is a conflict in the names of the Frame Relay meters
disk-copying meter groups.
11178
LAST METER IN METER GROUP NOT REMOVED
The last meter in a Frame Relay meters disk-copying
meter group cannot be removed.
11179
ACCESS TO NETWORK ELEMENT IS DENIED
Access to the network element is denied due to insufficient
access rights.
11180
INCORRECT FREQUENCY BAND USED
Frequency bands are not compatible.
11181
SIGNALLING FROM RING TO LOOP DID NOT
SUCCEED IN LIDN
Signalling from RING to LOOP did not succeed in LIDN.
370
DN987378
Issue: 30-0
General Error Messages of System
11182
Error messages
SIGNALLING FROM TEST TO ALARM DID NOT
SUCCEED IN LIDN
Signalling from TEST to ALARM did not succeed in LIDN.
11183
TEST CONNECTION TIME EXCEEDED
The test connection time on the LIDN plug-in unit has been
exceeded.
11184
FAILURE IN LIDN SIGNALLING
Subscriber signalling test on the LIDN plug-in unit was
unsucessfull.
11185
PERMANENT VIRTUAL CIRCUITS NOT ASSOCIATED
WITH CHANNEL GROUP
The Permanent Virtual Circuits (PVC) are not associated
with a channel group.
11186
CHANNELS USING ETHERNET TERMINAL ARE NOT
ASSOCIATED WITH CHANNEL GROUP
The physical channels which use the Ethernet terminal are
not associated with a channel group.
11187
LINE TERMINAL ALREADY LOOPED
The line terminal is already looped.
11188
LINE TERMINAL NOT LOOPED
The line terminal is not looped.
11189
PREANNOUNCEMENT SET
A preannouncement has been set for the destination.
11191
NO PREANNOUNCEMENT
There is no preannouncement on the destination.
11192
PRE-ANNOUNCEMENT NOT LAST DESTINATION
ALTERNATIVE
The pre-announcement is not the last alternative on the
destination.
11193
NO PERCENTAGE FOR PRE-ANNOUNCEMENT
No percentage to be defined for the pre-announcement
destination.
11194
PRE-ANNOUNCEMENT EXISTS
A destination alternative, leading to a pre-announcement,
already exists on the destination.
Issue: 30-0
DN987378
371
Error messages
General Error Messages of System
11195
SUBSCRIBER DOES NOT HAVE CALL-BACK FACILITY
The subscriber does not have the call-back facility in use.
11196
IMMEDIATE CHARGING IS ACTIVE
Immediate charging is active.
11197
INCORRECT KA CATEGORY
The KA category is incorrect.
11198
DO NOT DISTURB IS ALLOWED ONLY TO CENTREX
SUBSCRIBERS
The do not disturb facility is allowed only to CENTREX
subscribers.
11199
DIFFERENT NUMBER OF ARGUMENTS IN
PARAMETERS
The user has given two or more parameters, but they had
a different number of arguments.
11200
DOUBLE TELEPHONE NUMBER
A double subscriber number.
11201
RESERVED FOR DOUBLE TELEPHONE NUMBER
The subscriber number is reserved for a double telephone
number.
11202
SUBSCRIBER NUMBER WITH DOUBLE NUMBER
Subscriber number with double telephone number.
11203
LOGGING GROUP DOES NOT EXIS
Logging group does not exist.
11204
VACANT SUBSCRIBER NUMBER WITHOUT
COUNTERS
A subscriber number without counters is vacant.
11205
INCORRECT DOUBLE TELEPHONE NUMBER
A double subscriber number is incorrect.
11206
NOT A D-CHANNEL ET UNIT
There has been an effort to do something possible only
with an ET unit that has a D-channel.
11207
372
ET UNIT IS IN TRANSPARENT MODE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The ET unit is in the transparent mode, which means e.g.
that only some of the trunk PCM error statistics are
possible.
11208
FOLLOW-ME SUBSCRIBER
The subscriber type is "follow me".
11209
ROUTINE TEST REPORTING BUSY
Routine test reporting is busy. Try reporting later.
11210
MESSAGE BUS SENDING IS NOT POSSIBLE
The MBIF plug-in unit is not ready to send messages.
11211
MB SENDING DID NOT SUCCEED
The sending of a message bus message was not
successful.
11212
NO QUIT BYTE
The requested state and acknowledgement byte has failed
to arrive from the receiving MBIF plug-in unit, due to an
error in the sending of a message bus message.
11213
MB HEADER RECEIVING ERROR
When receiving a message bus message, an error was
detected in the reading of the header of the message.
11214
MB MESSAGE RECEIVING ERROR
When receiving a message bus message, an error was
detected after the reading of the header.
11215
BCCH ALLOCATION OPTION IS NOT IN USE IN BSC
The BCCH allocation option is not in use in the BSC.
11216
DISTURBANCE MEASUREMENTS ARE NOT POSSIBLE
IN CURRENT MODE
This error appears when the MML user tries to obtain
measurements about disturbances of the PCM line of
ET2E while the set mode does not provide these
measurements.
11217
FRAMING ERROR MEASUREMENTS ARE NOT
POSSIBLE IN CURRENT MODE
This error appears when the MML user tries to obtain
framing error measurements of the PCM line of ET2E
while the set mode does not provide these measurements.
Issue: 30-0
DN987378
373
Error messages
General Error Messages of System
11218
SLIP MEASUREMENTS ARE NOT POSSIBLE IN
CURRENT MODE
This error appears when the MML user tries to obtain slip
measurements of the PCM line of ET2E while the set
mode does not provide these measurements.
11219
INCORRECT NMT IDENTIFICATION
A DAXnode subscriber is not found by NMT identification.
11220
INCORRECT PCM-TSL
A DAX subscriber is not found on the basis of his PCMTSL.
11221
TSC (BCCH OR PBCCH TRX) AND BCC (CELL) VALUES
MUST BE EQUAL
The Training Sequence Codes of the TRXs and the BTS
Colour Code of the BTS must be equal.
11222
MBIF NOT USABLE
There is no MBIF plug-in unit, or it is unavailable for some
other reason.
11223
CALL RETURN NUMBER
A call return number.
11224
PARALLEL ORDINARY SERVICE NUMBER
A parallel ordinary service number.
11225
PARALLEL CX SERVICE NUMBER
A parallel Centrex service number.
11226
PARALLEL RSU PBX NUMBER
A parallel PBX number of an RSU.
11227
PARALLEL FREE SUBSCRIBER NUMBER WITHOUT
SUBSCRIBER METERS
There is a parallel free subscriber number without
subscriber meters.
11228
PARALLEL DOUBLE SUBSCRIBER NUMBER
Parallel double subscriber number.
11229
ADMINISTRATIVE STATE OF THE OBJECT IS
INCORRECT
The administrative state of the object in the radio network
database is unsuitable for the requested operation.
374
DN987378
Issue: 30-0
General Error Messages of System
11230
Error messages
MAFILE OF OTHER PACKAGE IN DIRECTORY NOT OK
The MAFILE file of the other package in the directory is not
OK, or it cannot be read.
11231
PACKAGE NOT IDENTICAL WITH OTHER PACKAGE IN
DIRECTORY
The package is not the same as the other package in the
directory.
11232
EXISTING DIRECTORY TOO SMALL
The existing directory is too small.
11233
UNIT TYPE TO DISK BIT MASK CONVERSION LIBRARY
ERROR
The conversion - by means of a library program - of a unit
type to a disk bit mask has failed.
11234
FOLLOW ME SUBSCRIBER
This is a FOLLOW ME subscriber.
11235
FOLLOW ME SUBSCRIBER VACANT
This FOLLOW ME subscriber is vacant.
11236
FOLLOW ME SUBSCRIBER RESERVED
FOLLOW ME subscriber is reserved.
11237
PARALLEL FOLLOW ME SUBSCRIBER
Parallel FOLLOW ME subscriber.
11238
BTS POWER CONTROL PARAMETERS NOT FOUND IN
DATABASE
BTS power control parameters have not been created into
the radio network database.
11239
BTS HANDOVER CONTROL PARAMETERS NOT
FOUND IN DATABASE
BTS handover control parameters have not been created
into the radio network database.
11240
COMMAND PARTLY SUCCESSFUL: VLR NOT UPDATED
The data cannot be transferred to VLR correctly. The MAP
interface rejects the given operation. However, the data
has been stored in the HLR database.
11241
SYMBOL NOT FOUND
Symbol is not found.
Issue: 30-0
DN987378
375
Error messages
General Error Messages of System
11242
AMBIGUOUS SYMBOL NAME
Symbol name is ambiguous.
11243
AMBIGUOUS PACKAGE ID
The given software package identification is ambiguous.
11244
ILLEGAL DESTINATION NETWORK ELEMENT
The given network element is not a legal destination for a
remote SW package transfer.
11245
NETWORK ELEMENT NOT FOUND
Network element is not found.
11246
TRANSFER IN PROGRESS
Transfer is in progress.
11247
TRANSFER NOT IN PROGRESS
Transfer is not in progress.
11249
BTS NAME IS ILLEGAL
A BTS name may consist of allowed characters only.
11250
BTS NAME ALREADY IN USE
A BTS name must be unique in the BSC.
11251
REQUESTED OPERATION NOT SUPPORTED BY THE
DEFINED SITE TYPE
The requested operation is not possible with the defined
site type. The site type is a parameter of the BCF object.
11252
REQUESTED OPERATION IS NOT ALLOWED TO
FLOATING-TYPE TRX
The requested operation is not possible with TRX of the
floating type. The TRX type is a parameter of a TRX
object.
11253
RF HOPPING BTS USING MA LIST MUST BE LOCKED
Modification is possible only if the administrative state(s) of
the RF (Radio Frequency) hopping BTS(s) using the MA
list is (are) LOCKED.
11254
OPERATION REQUIRES THAT RF HOPPING BTS MUST
BE LOCKED
The operation was rejected because an RF hopping BTS
was not locked. The administrative state of the BTS must
be LOCKED.
376
DN987378
Issue: 30-0
General Error Messages of System
11255
Error messages
SIMULTANEOUS BB AND RF HOPPING IS NOT
ALLOWED UNDER BCF
The operation was rejected because in a BCF there are
BTSs with simultaneously defined BB (Base Band) and RF
(Radio Frequency) hopping.
11256
FREQUENCY OF CELLS BCCH TRX IS NOT ALLOWED
TO BE IN CELLS MA LIST
An operation was rejected because the frequency of
BCCH TRX of a cell is in the MA list of the cell.
11257
INCORRECT FREQUENCY FOR USED BAND
The frequency does not belong to the specified (GSM or
DCS) band.
11258
BCCH TRX ARFCN IS NOT ALLOWED TO BE IN MA
LIST OF BTS
In RF (Radio Frequency) hopping it is not allowed to have
an ARFCN of a BCCH TRX in the MA list of a BTS.
11259
TOO FEW ARFCNS IN MA LIST USED BY CELL
The number of RF-hopping TRXs and Maio Offset (MO)
and Maio Step (MS) parameters affect the number of
frequencies on the MA list.
11260
MA LIST NOT FOUND IN RNW DATABASE
The MA list must be created before any BTS can be
attached to it.
11261
MA LIST IS STILL USED BY SOME BTS
An MA list cannot be deleted if it is used by a BTS.
11262
MA FREQUENCY LIST IS FULL
No new frequency can be added to the MA list because
the frequency list is full.
11263
ADMINISTRATIVE STATE OF HOPPING CELL MUST BE
LOCKED
The operation requires that the hopping BTS is locked.
11264
FR USER ACCESS NOT PASSIVATED
A Frame Relay user access has not been deactivated.
11265
FRAME RELAY USER ACCESS NOT ACTIVATED
A Frame Relay user access has not been activated.
Issue: 30-0
DN987378
377
Error messages
General Error Messages of System
11266
BCC+NCC+BCCH TRX FREQUENCY NOT UNIQUE IN
ADJACENCY DEFINITIONS
The BCC + NCC + BCCH TRX frequency parameter
combination must be unique for each member in the
neighbour list of a cell. The list for each cell is collected
from the neighbour definitions of the cell and the list is
used in MS measurements. The BCC + NCC + BCCH TRX
frequency uniqueness can be checked with the adjacent
cell MML.
11267
NO MORE REQUESTED DATA
There is no more data. All data has already been given.
11268
DIRECT DIALLING-IN HAS BEEN SET
The DDI facility has been set for the subscriber.
11269
UNKNOWN TRX ID
A configuration mismatch has been found between
GUPDAT and Abis-signalling program blocks, or a
message was corrupt.
11270
UNKNOWN BTS ID
A configuration mismatch has been found between
GUPDAT and Abis-signalling program blocks, or a
message was corrupt.
11271
UNKNOWN BCF ID
A configuration mismatch has been found between
GUPDAT and Abis-signalling program blocks, or a
message was corrupt.
11272
MOBILE ALLOCATION NOT AVAILABLE
Mobile allocation table length is zero.
11273
CELL ALLOCATION NOT AVAILABLE
Cell allocation table length is zero.
11274
TOO MANY VALUES IN MOBILE ALLOCATION TABLE
Mobile allocation table length is greater than allowed.
11275
TOO MANY VALUES IN CELL ALLOCATION TABLE
Cell allocation table length is greater than allowed.
11276
ZERO VALUE IN MOBILE ALLOCATION TABLE
Zero frequency value in mobile allocation table.
11277
378
ZERO VALUE IN CELL ALLOCATION TABLE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Zero frequency value in cell allocation table.
11278
INVALID VALUE IN MOBILE ALLOCATION TABLE
Invalid arfcn value in mobile allocation table.
11279
INVALID VALUE IN CELL ALLOCATION TABLE
Invalid arfcn value in cell allocation table.
11280
IN MOBILE ALLOCATION TABLE TWO ARFCN HAVE
SAME VALUE
In mobile allocation table two arfcn have same value.
11281
IN CELL ALLOCATION TABLE TWO ARFCN HAVE SAME
VALUE
In cell allocation table two arfcn have same value.
11282
ZERO FREQUENCY VALUE IN ABIS INTERFACE
INTERNAL ARFCN TABLE
In Abis interface internal arfcn table has zero frequency
value.
11283
TOO MANY ARFCN VALUES OR DIFFERENCE
BETWEEN GREATEST AND SMALLEST VALUES IS
TOO BIG
Overflow in Abis interface internal arfcn table.
11284
TEMPORARILY OVERLOAD
There are too many TRXs in the TRX list of the conf_data
message. Check the TRX count.
11285
AOM SLAVE HAS NOT ANSWERED SUPERVISION
MESSAGE TO AOMPRB MASTER
AOM slave has not answered supervision message to
AOMPRB master.
11286
MAXIMUM AMOUNT OF BCF IDS IN USE
NO MORE SPACE TO SAVE BCF INFORMATION IN
AOMPRB
11287
MAXIMUM AMOUNT OF TRX IDS IN USE
Maximum amount of trx ids in use.
11288
INVALID RADIO TSL TYPE DETECTED
Invalid radio tsl type detected.
11289
Issue: 30-0
CREATION OF HAND HAS FAILED IN ABIPRB
DN987378
379
Error messages
General Error Messages of System
Creation of hand has failed in ABIPRB, probably because
of operation system error.
11290
DELETION OF HAND HAS FAILED IN ABIPRB
Deletion of hand has failed in ABIPRB, probably because
of operation system error.
11291
HAND CREATION PROCEDURE HAS FAILED IN ABIPRB
Hand Creation procedure has failed in ABIPRB, probably
because of operation system error.
11292
CCCH HAND HAS NOT RESPONDED TO REQUEST
TASK
CCCH hand has not responded to request task.
11293
SDCCH OR TCH HAND HAS NOT RESPONDED TO
REQUEST TASK
SDCCH or TCH hand has not responded to request task.
11294
DELETION OF TRX HAS FAILED
Deletion of TRX has failed because PXRECE has not
responded to request task.
11295
TOO MANY ARFCN VALUES (B_M_0)
Creation of bm0 format fails because of too many arfcn
values.
11296
TOO MANY ARFCN VALUES (V_B_M)
Creation of vbm fails because of too many arfcn values.
11297
TOO MANY ARFCN VALUES (R256)
Creation of range 256 fails because of too many arfcn
values.
11298
TOO MANY ARFCN VALUES (R512)
Creation of range 512 fails because of too many arfcn
values.
11299
THE DIFFERENCE BETWEEN GREATEST AND
SMALLEST FREQUENCY IS TOO HIGH (B_M_0)
Creation of bm0 fails because the difference between the
greatest and the smallest arfcn value is too high.
11300
DIFFERENCE BETWEEN GREATEST AND SMALLEST
FREQUENCY IS TOO HIGH (V_B_M)
Creation of vbm fails because difference between greatest
and smallest arfcn value is too high.
380
DN987378
Issue: 30-0
General Error Messages of System
11301
Error messages
DIFFERENCE BETWEEN GREATEST AND SMALLEST
FREQUENCY IS TOO HIGH (R256)
Creation of range 256 fails because difference between
greatest and smallest arfcn value is too high.
11302
DIFFERENCE BETWEEN GREATEST AND SMALLEST
FREQUENCY IS TOO HIGH (R512)
Creation of range 512 fails because difference between
greatest and smallest arfcn value is too high.
11303
WRONG PARAMETER VALUE IN CONF DATA
MESSAGE
WRONG PARAMETER VALUE IN CONF DATA
MESSAGE.
11304
TOO MANY TRXS ON THE BCF
There are too many TRXs in the TRX list of the conf_data
message. Check the TRX count.
11305
TEMPORARY OVERLOAD, NO RESOURCES
AVAILABLE
There is a temporarily overload. No resource are available.
Try again later.
11306
TEMPORARILY OVERLOAD. NO RESOURCE
AVAILABLE.
Temporarily overload. No resource available. Try again
later.
11309
SUBSCRIBER PASSIVE
The WLL subscriber does not respond to a call attempt.
The subscribers terminal may be faulty or just switched off.
11310
APPLICATION CREATION IN DATABASE FAILED
The creation of a new application object in the OEDATA
database has failed.
11311
APPLICATION ALREADY EXISTS IN DATABASE
The application already exists in the OEDATA database.
11312
APPLICATION DOES NOT EXIST IN DATABASE
The application does not exist in the OEDATA database.
11313
APPLICATION IS UNLOCKED
The administrative state of an application object in the
OEDATA database is unlocked.
Issue: 30-0
DN987378
381
Error messages
General Error Messages of System
11314
SERVICE PROFILE CREATION IN DATABASE FAILED
The creation of an application service profile object in the
OEDATA database has failed.
11315
SERVICE PROFILE ALREADY EXISTS IN DATABASE
The application service profile already exists in the
OEDATA database.
11316
SERVICE PROFILE DOES NOT EXIST IN DATABASE
The application service profile does not exist in the
OEDATA database.
11317
SELECTOR SET CREATION IN DATABASE FAILED
The creation of an additional selector set object (of an
application) in the OEDATA database has failed.
11318
SELECTOR SET ALREADY EXISTS IN DATABASE
The additional selector set of the application already exists
in the OEDATA database.
11319
SELECTOR SET DOES NOT EXIST IN DATABASE
An additional selector set of an application does not exist
in the OEDATA database.
11320
NETWORK ADDRESS CREATION IN DATABASE FAILED
The creation of a network address object in the OEDATA
database has failed.
11321
NETWORK ADDRESS ALREADY EXISTS IN DATABASE
The network address already exists in the OEDATA
database.
11322
NETWORK ADDRESS DOES NOT EXIST IN DATABASE
The network address does not exist in the OEDATA
database.
11323
NSAP CREATION IN DATABASE FAILED
The creation of an NSAP (Network Service Access Point)
object in the OEDATA database has failed.
11324
NSAP ALREADY EXISTS IN DATABASE
The Network Service Access Point (NSAP) already exists
in the OEDATA database.
11325
382
NSAP DOES NOT EXIST IN DATABASE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The Network Service Access Point (NSAP) does not exist
in the OEDATA database.
11326
NSAP IS UNLOCKED
The administrative state of an NSAP object in the OEDATA
database is unlocked.
11327
CLNS CREATION IN DATABASE FAILED
The creation of a new CLNS (Connectionless Network
Service) object in the OEDATA database has failed.
11328
CLNS ALREADY EXISTS IN DATABASE
The CLNS (Connectionless Network Service) already
exists in the OEDATA database.
11329
CLNS DOES NOT EXIST IN DATABASE
The CLNS (Connectionless Network Service) does not
exist in the OEDATA database.
11330
CLNS IS UNLOCKED
The administrative state of the CLNS object in the
OEDATA database is unlocked.
11331
CREATION OF LINKAGE IN DATABASE FAILED
The creation of a linkage object in the OEDATA database
has failed.
11332
LINKAGE ALREADY EXISTS IN DATABASE
The linkage already exists in the OEDATA database.
11333
LINKAGE DOES NOT EXIST IN DATABASE
The linkage does not exist in the OEDATA database.
11334
LINKAGE IS UNLOCKED
The administrative state of a linkage object in the OEDATA
database is unlocked.
11335
NETWORK ADDRESS IS IN USE
The network address is attached to an application and
cannot be deleted.
11336
NSAP ATTACHED TO NETWORK ADDRESS
The network address cannot be deleted, because one or
more NSAPs are attached to it.
11337
Issue: 30-0
SEARCH MASK IS NOT OK
DN987378
383
Error messages
General Error Messages of System
The search mask used in inquiries about the OEDATA
database is not OK.
11338
PARALLEL FAULTMANS RINGBACK SUBSCRIBER
The faultmans ringback subscriber has a parallel number.
11339
FAULTMANS RINGBACK SUBSCRIBER NUMBER BUSY
The faultmans ringback subcriber number is busy.
11340
FAULTMANS RINGBACK SUBSCRIBER IS FREE
The faultmans ringback subscriber number is free.
11341
FAULTMANS RINGBACK SUBSCRIBER
Faultmans ringback subscriber.
11342
OBJECT ID OUT OF LIMITS
An objects ID value is either too low (BTS = 0, TRX = 0) or
too high (BTS > 80H, TRX > 10H, TSL > 7H).
11343
BTS ALREADY EXISTS
The BTS in question has already been created.
11344
GIVEN BTS DOES NOT EXIST
The given BTS has not been created in the configuration.
11345
MAXIMUM NUMBER OF TRXS ALREADY CREATED
All possible TRXs have already been created, i.e. the
maximum number of TRXs has been reached.
11346
TRX ALREADY EXISTS
The TRX in question has already been created.
11347
GIVEN TRX DOES NOT EXIST
The given TRX has not been created in the configuration.
11348
TRX IN WRONG STATE FOR THE OPERATION
The given TRX is not in the right state for the operation in
question.
11349
GIVEN TRX ALREADY IN WORKING STATE
The given TRX is already in the WORKING state.
11350
WRONG TSL TYPE FOR THE OPERATION
The type of the given TSL is not appropriate for the
intended operation.
384
DN987378
Issue: 30-0
General Error Messages of System
11351
Error messages
GIVEN TSL ALREADY IN WORKING STATE
The given TSL is already in the WORKING state.
11352
TRX NOT IN WORKING STATE
The given TRX is not in the WORKING state, as expected
in the operation.
11353
TSL NOT IN WORKING STATE
The given TSL is not in the WORKING state, as expected
in the operation.
11354
BTS ALARM SYSTEM FILE IS FULL
The Alarm History File of a BTS is full.
11355
BTS ALARM HISTORY FILE IS FULL IN BCF
The Alarm History File of a BTS is full in the BCF.
11356
BTS ALARM SYSTEM FILTER BUFFER OVERFLOW
There is an overflow in the BTS alarm system filter buffer.
11357
BTS ALARM SYSTEM OUTPUT BUFFER OVERFLOW
There is an overflow in the BTS alarm system output
buffer.
11358
CPE PASSIVE
A Customer Premises Equipment (CPE) does not respond
to call attempts. The subscriber terminal may be faulty or
just switched off.
11359
DIRECTED RETRY OPTION IS NOT IN USE IN BSC
The directed retry feature, which is used in the call set-up
phase when assigning (when congestion occurs) a mobile
station to a traffic channel in a cell other than the serving
cell, is not supported in the BSC.
11360
C2 CELL RESELECTION OPTION IS NOT IN USE IN
BSC
The C2 cell reselection feature is not supported in BSC.
The purpose of C2 cell reselection is to control cell
reselection of mobile stations in idle status.
11361
FACCH CALL SET-UP OPTION IS NOT IN USE IN BSC
The FACCH call set-up feature is not supported in the
BSC.
11362
Issue: 30-0
REMOTE DEGRADATION OF BTS SERVICE OPTION IS
NOT IN USE IN BSC
DN987378
385
Error messages
General Error Messages of System
The remote degradation of BTS service under transceiver
shutdown is not supported in the BSC.
11363
ADMINISTRATIVE STATE IS NOT ONLY ATTRIBUTE TO
BE MODIFIED
The user tries to modify both the administrative state and
other attributes at the same time.
11364
REQUESTED OPERATION MAY BE PARTLY
SUCCESSFUL DESPITE ERROR
The requested operation may be partly successful despite
the error or errors that occured during the handling of the
operation.
11365
DATABASE FORMAT IS NOT SUPPORTED BY BTS
The database format is not supported by the BTS.
11366
NO SUCH CLOSED USER GROUP
There was no such closed user group.
11367
FATAL ERROR DURING FLASH OPERATION
A fatal error occurred during the flash operation.
11368
MEMBER IN CLOSED USER GROUP
There is a member in a closed user group.
11369
ILLEGAL FILE TYPE
Illegal file type.
11370
FLASH MEMORY HAS NOT BEEN SEGMENTED
The flash memory of a BTS has not been segmented.
11371
CELL CONFIGURATION MISMATCHES WITH THE
CURRENT HARDWARE
The cell configuration does not match with the current
hardware.
11372
INVALID HOPPING MODE DUE TO HARDWARE
LIMITATIONS
The hopping mode is invalid, due to hardware limitations.
11373
NO FLOATING TRX INSTALLED AT BTS SITE
No floating TRX is installed at the BTS site.
11374
386
HOPPING BTS HAS INCORRECT ADMINISTRATIVE
STATE FOR REQUESTED TASK
DN987378
Issue: 30-0
General Error Messages of System
Error messages
A Base Station with frequency hopping in use has an
administrative state which is not suitable for the requested
task. Certain configuration changes in a hopping cell are
not allowed when the BTS is in the UNLOCKED state.
11375
UNKNOWN BASE STATION ALARM V-PARAMETERS
The V-parameters of the base station alarm do not exist in
the DEFBSA file.
11376
FOLLOW ME SUBSCRIBER ALREADY EXISTS
A Follow Me subscriber for this area code already exists.
11377
FAULTMANS RINGBACK SUBSCRIBER ALREADY
EXISTS
A Faultmans Ringback subscriber for this area code
already exists.
11378
CLOSED USER GROUP RESERVED
The closed user group has already been reserved.
11379
ALL SUBSCRIBERS NOT AVAILABLE
The call generator needs subscriber pairs, and all
subscribers have not been created.
11380
CALL GENERATOR NOT STARTED
The call generator did not start.
11381
BAD OUTGOING ATM LINE NUMBER
An outgoing ATM line number exceeds the allowed limits.
Bad connection message data is received, or the HW
configuration data differs from the AXRMGR database
data.
11382
BAD INCOMING ATM LINE NUMBER
An incoming ATM line number exceeds the allowed limits.
Bad connection message data is received, or the HW
configuration data differs from the AXRMGR database
data.
11383
SWCOP FIFO IS RESERVED
The SWCOP FIFO is reserved during an attempt to make
a connection. Another process has reserved the FIFO for
data transfer.
11384
SWCOP WRITE BUFFER FULL
The SWCOP unit is not reading connection data from the
FIFO. The SWCOP software is either busy or faulty.
Issue: 30-0
DN987378
387
Error messages
General Error Messages of System
11385
NO CONNECTION ACKNOWLEDGEMENT FROM
SWCOP
The SWCOP unit is not responding to the connection
message. The FIFO transmission failed, bad data was
read from FIFO, or the SWCOP unit is faulty.
11386
SWCOP RESTART FAILURE
Restarting the SWCOP unit failed. The unit is missing or
faulty, or bad HW configuration data is to blame.
11387
SWCOP UNIT NOT INITIALISED
There was an attempt to make a connection through an
uninitialized SWCOP unit. The unit is restarted or HW
configuration changes are made without re-initializations.
11388
ASWI UNIT NOT INITIALISED
There was an attempt to make a connection to an
uninitialized ASWI unit. The unit is reset or HW
configuration changes are made without reinitializing the
unit.
11389
CONNECTION TYPE MISMATCH
There has been a type mismatch on the connection data
and/or the line types. There was an attempt to make a VP
connection on a VC line or vice versa.
11390
PARITY ERROR ON CONNECTION
The connection failed on the ASWI unit. Hardware failure.
11391
CONNECTION MEMORY CHECK FAILURE
Data read from the ASWI connection memory differs from
written connection data. The connection failed. ASWI HW
is faulty.
11392
ASWI INITIALISATION FAILED
ASWI unit initialisation has failed. The unit is missing, or
bad, or HW configuration data is bad.
11393
ATM CONNECTION TYPE MISMATCH
The attempted transaction was incompatible with the
current configuration of the ATM switch matrix (ASWI plugin unit). For example, a request has been made for a
Virtual Channel Connection on a line set to handle Virtual
Path Connections.
11394
388
HW DATABASE FILE(S) ALREADY EXISTS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The BCF HW database file(s) has already been found on
the disk(s) of the BSC.
11395
NO HW DATABASE DOWNLOAD REQUEST FROM BCF
BTDOWN has not received a HW database file download
request from BCF (via AOMPRB).
11396
INCORRECT HW DATABASE DOWNLOAD REQUEST
FROM BCF
BTDOWN has received an incorrect HW database
download request from BCF (via AOMPRB). There might
be a conflict between the BCF type and the type of the
requested file.
11397
NO FILE RECORD FROM BCF
The HW database uploading has been interrupted
because of a missing file record from BCF (via AOMPRB).
11398
INCORRECT FILE RECORD FROM BCF
BTDOWN has received an incorrect file record from BCF
(via AOMPRB). The location of the record in the file may
be unknown.
11399
ERROR IN HW DATABASE FILE LOADING
A HW database file loading operation has been interrupted
by an internal error in BTDOWN.
11400
OPERATION NOT SUCCESSFUL ON BOTH DISKS
BTDOWN has failed in a disk operation on both disks in
BSC.
11401
ONGOING SOFTWARE DOWNLOAD OPERATION IN
BCF
The HW database operation is denied because of ongoing
software package downloading in the same BCF.
11402
HW DATABASE OPERATION INTERRUPTED BY SW
OPERATION
The HW database operation has been interrupted by an
SW package download request.
11403
UNKNOWN BTS SITE TYPE
The type of BTS site (BCF) is unknown.
11404
Issue: 30-0
SPARE UNIT IN RESTART STATE, TRY AGAIN
DN987378
389
Error messages
General Error Messages of System
The spare unit was in the restarting state while the active
unit was trying to make radio network configuration
changes. Try again after the restarting of the spare unit is
completed.
11405
PARAMETERS DO NOT COINCIDE
There is an inconsistency between the parameters given in
a command.
11406
INCORRECT BASE STATION STATE
The defined base station is not in such a working state as
the given task requires.
11407
BASE STATION CHANNELS NOT OUT OF USE
The channels of the base station are not out of use,
although the task requires it.
11408
INCORRECT BASE STATION CIRCUIT STATE
The defined base station circuit is not in such a working
state as the given task requires.
11409
CORRESPONDING DSP IS FAULTY
The corresponding DSP of the SPU-U plug-in unit is faulty.
11410
NO RESPONSE FROM USAPRO
No acknowledgement has been received from the
USAPRO program block to the DSP status inquiry.
11411
BASE STATION ET IS IN WRONG WORKING STATE
The base station ET is in the wrong working state.
11412
BASE STATION CIRCUIT NOT IN CONFIGURATION
The defined base station circuit does not belong to the
radio network configuration.
11413
PCM NOT IN CONFIGURATION
The defined PCM does not belong to the radio network
configuration.
11414
CIRCUIT NOT IN USE IN THIS BASE STATION
The base station circuit does not belong to the given base
station.
11415
BASE STATION CIRCUIT ALREADY IN USE
The base station circuit which someone tried to add to the
configuration is already in use.
390
DN987378
Issue: 30-0
General Error Messages of System
11416
Error messages
BASE STATION HAS CIRCUITS IN USE
The deletion of a base station is not possible because of
circuits connected to the base station.
11417
NO CIRCUITS CONNECTED TO BASE STATION
Interrogation of base station circuits is not possible,
because there are no circuits connected to the base
station.
11418
CHANNEL NUMBER ALREADY IN USE
Adding or modifying a channel number was not possible,
because the given channel number is already in use.
11419
CHANNEL NUMBER IS NOT IN USE
The given channel number is not in use.
11420
BASE STATION ALREADY EXISTS
The base station given in the adding or modifying
command already exists.
11421
BASE STATION IS NOT IN CONFIGURATION
The specified base station does not belong to the radio
network configuration.
11422
DEFAULT BS NOT CREATED
The default base station values cannot be used in the
creation of a new base station, because the default base
station is not created.
11423
TRAFFIC AREA IS ALREADY IN CONFIGURATION
The specified traffic area is already in the configuration.
11424
TRAFFIC AREA NOT IN CONFIGURATION
The specified traffic area does not belong to the radio
network configuration.
11425
BASE STATIONS STILL CONNECTED TO TRAFFIC
AREA
Base stations are still connected to the traffic area that was
specified in the deletion command.
11426
BASE STATION ALREADY DEFINED TO THIS TRAFFIC
AREA
The base station specified belongs already to this traffic
area.
11427
Issue: 30-0
BASE STATION BELONGS TO NO TRAFFIC AREA
DN987378
391
Error messages
General Error Messages of System
The specified base station does not belong to any traffic
area.
11428
TRAFFIC AREA NUMBER ALREADY IN USE
The defined traffic area number is already in use.
11429
BASE STATION BELONGS TO ANOTHER TRAFFIC
AREA
The defined base station belongs to another traffic area.
11430
DISK AND SPARE UNIT UPDATE FAILURE
Both disk and spare unit updating has failed.
11431
CALLING CHANNEL NOT IN BASE BAND
The defined calling channel limits are not within base band
limits.
11432
USE OF ACCESS CHANNELS NOT POSSIBLE IN THIS
BASE STATION
The use of access channels in this base station is
impossible due to the radio network configuration.
11433
USE OF COMBINED CHANNELS NOT POSSIBLE IN
THIS BASE STATION
The use of combined channels in this base station is
impossible due to the radio network configuration.
11434
INAPPROPRIATE NUMBER OF DATA CHANNELS
There is an inappropriate number of data channels in this
base station.
11435
BASE STATION HAS ONLY NECESSARY CIRCUITS
LEFT
Circuits cannot be deleted, because the base station has
only the necessary circuits left.
11436
BASE STATION HAS SUFFICIENT DDCS
The channel type cannot be changed, because the base
station already has sufficient data channels.
11437
ONLY ONE CALLING CHANNEL POSSIBLE IN THIS
BASE STATION
Only one calling channel is possible in this base station,
due to the radio network configuration.
11438
392
INCORRECT CHANNEL NUMBER
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The interrogating or modifying of a base station circuit
state, using a channel number, has not succeeded
because of an undefined channel number.
11439
BASE STATION DOES NOT HAVE ALL SUFFICIENT
CHANNELS
The base station does not have all the channels it needs,
so its working state cannot be changed to WO.
11440
BASE STATION HAS ALREADY ONE CHANNEL IN TEST
USE
There was an attempt to add a test channel to a base
station which already has one.
11441
NO BASE STATION BELONGS TO THIS TRAFFIC AREA
The defined task cannot be executed, because the defined
traffic area has no base stations.
11442
NO MORE PCMS CONNECTED
All PCMs have been interrogated by the circuit state
interrogation command. The last information on circuits
was sent in the previous answer.
11443
NO MORE CIRCUITS OF THIS TYPE
All circuits of the given type have been interrogated by the
circuit state interrogation command. Last information was
sent in previous answer.
11444
NO MORE CONNECTED CIRCUITS LEFT
All circuits have been handled, when changing their states
by command.
11445
NO MORE BASE STATIONS LEFT
All base stations have been handled, when interrogating
them by using a command.
11446
CHANNEL STILL RESERVED
Channel status is occupied.
11448
SUITABLE SUBDESTINATION NOT FOUND
CMREAD has not found a suitable subdestination from a
destination.
11449
SUBDESTINATION OVERFLOW NOT ALLOWED DESTINATION BARRED
It is not allowed to try another subdestination, or else the
destination is barred.
Issue: 30-0
DN987378
393
Error messages
General Error Messages of System
11450
ATM USER ACCESS EXISTS
This error occurs when an attempt is made to create an
ATM user access which already exists (e.g. the access
identifier is already defined).
11451
ATM USER ACCESS DOES NOT EXIST
This error arises when a transaction is attempted for an
ATM user access that does not exist.
11452
ATM USER ACCESS USED BY VIRTUAL CONNECTION
This error code is generated when an attempt is made to
delete an ATM user access for which at least one virtual
connection still exists.
11453
ATM USER ACCESS NOT INACTIVATED
Certain transactions can only be performed on an ATM
user access which has been previously set to an inactive
state. If such a transaction is attempted upon an active
ATM user access it will result in the generation of this error
code.
11454
ATM USER ACCESS NOT ACTIVATED
An ATM user access has not been activated.
11455
STATE CHANGE FAILED
The changing of the administrative state of an object in the
OEDATA database has failed.
11456
REMOTE MMI CONNECTION HANDLING SYSTEM
BUSY (RETMMI PROGRAM BLOCK)
The RETMMI program block cannot create a new hand,
yet the maximum number of hands has not been reached.
11457
NO FREE REMOTE MMI CONNECTIONS
The maximum number of remote MMI connections is
already in use.
11458
UNFINISHED CONNECTION TO BCF EXISTS
A new connection cannot be established because there is
still an unfinished operation in this BCF.
11459
ACKNOWLEDGEMENT MESSAGE FROM AOMPRB
MISSING
The AOMPRB program block does not answer to a
connection request.
11460
394
MEMBER OF PRIVATE ISDN NETWORK
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The subscriber is a member of a private ISDN network.
11461
MEMBER OF PRIVATE ANALOGUE NETWORK
The subscriber is a member of an analogue private
network.
11462
GROUP CALL NUMBER OF PRIVATE ISDN NETWORK
The number of the subscriber is the group call number of a
private ISDN network.
11463
GROUP CALL NUMBER OF PRIVATE ANALOGUE
NETWORK
The subscriber number is the group call number of a
private analogue network.
11464
INCORRECT BASE STATION CHANNEL STATE
The defined base station channel is not in the working
state that the given task requires.
11465
VIRTUAL PATH TABLE ERROR
The FR/ATM Connection Handling Program Block
(FBHAND) maintains a work table to manage the supply of
virtual path routing data to the ATM Multiplexer Unit. This
error is generated if in the course of updating the table a
problem is encountered. An example of such a problem
would be that the permitted ratio of ATM Multiplexer Units
to Cell Relay Subscriber Units has been exceeded.
11466
SUBSCRIBER IS ALREADY A HUNTING GROUP
MEMBER
The subscriber is already a member in a hunting group.
11467
SDCCH HANDOVER OPTION IS NOT IN USE IN BSC
The SDCCH Handover feature is not in use in the BSC.
11468
RXQUAL STATISTICS AND HANDOVER
ADJACENT~CELL MEASUREMENT OPTION IS NOT IN
USE IN BSC
The RXqual statistics and handover adjacent cell
measurement features are not in use in the BSC.
11469
REMOTE INTERROGATION OF BTS SERIAL AND
VERSION NUMBERS OPTION IS NOT IN USE IN BSC
The remote interrogation of the serial and version numbers
of a BTS (HW configuration) via the Q3 interface is not in
use in the BSC.
11470
Issue: 30-0
LOCAL COPY SERVICE WAS PARTLY SUCCESSFUL
DN987378
395
Error messages
General Error Messages of System
The OVFSRP program block has received a local copy
request to several I/O devices (e.g. both Winchester
disks), but has not been able to copy to all of them, or the
data amount in the source is less than requested.
11471
LOCAL COPY HAS SUCCEEDED BUT DESTINATION
FILE IS FULL
OVFSRP has performed the requested local copy
operation, but the destination file became full. This is not
an error, but a notice to the user for changing the output
file.
11472
LOCAL COPY SERVICE FAILED BECAUSE READING
SOURCE FAILED
The local copy service provided by the OVFSRP program
block was unsuccessful because the reading source (a file
or a buffer) failed.
11473
LOCAL COPY SERVICE FAILED BECAUSE WRITING TO
DESTINATION FAILED
The local copy service provided by the OVFSRP program
block was unsuccessful because the writing to the
destination (a file or a buffer) failed.
11474
LOCAL COPY SERVICE FAILED
The local copy service provided by the OVFSRP program
block has failed for some unknown reason.
11475
REFERENCE NUMBERS ARE NOT SAME IN UPDATING
AND ACKNOWLEDGEMENT MESSAGES
The reference numbers in updating and acknowledgement
messages are not the same.
11476
ATM CONNECTION MODE MISMATCH ERROR
ATM connections can be either of two modes:
unidirectional - data passed in one direction only, and
bidirectional - data passed in both directions. In certain
situations the requested mode of connection is not
possible and results in the generation of this error code.
Example: Operator requests a spare connection where the
primary connection is unidirectional. This kind of service is
only possible with bidirectional connections.
11477
SIGNALLING BETWEEN STM AND NETWORK FAILED
Signalling between the STM and the network has failed.
11478
396
NUMBER OF TRXS DEFINED IN CONFIGURATION
MESSAGE IS INCONSISTENT WITH BTS DATABASE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The number of TRXs defined in the configuration message
is not consistent with the BTS database.
11479
INVALID PARAMETERS FOR CLNS
The parameters of the CLNS are faulty. Creation or
modification is not possible.
11480
UNABLE TO LOCK ACTIVE CLNS
The locking of an active CLNS is prohibited.
11482
OMNFIL HANDLING FAILED
The reading or writing of the OMNFIL file has failed.
11483
READING OF OFLPAR FAILED
The reading of the OFLPAR file has failed.
11484
HANDLING OF OMLFIL FAILED
Reading from or writing to the OMLFIL file has failed.
11485
HANDLING OF OMDFIL FAILED
Reading from or writing to the OMDFIL file has failed.
11486
CLNS MUST BE LOCKED FOR THIS OPERATION
The CLNS must be locked for this operation.
11487
INVALID PARAMETERS FOR LINKAGE
The parameters of the linkage are faulty. Modification or
creation of linkage is not possible.
11488
LINKAGE PARAMETER SET NOT FOUND
The parameter set of the linkage for default values is not
found.
11489
ACTIVATION OF ATTRIBUTE MODIFICATION FAILED
The activation of given attributes has failed. The active
CLNS uses the values of old attributes.
11490
LINKAGE MUST BE LOCKED FOR THIS OPERATION
The linkage must be locked for this operation.
11491
ATM NODE DOES NOT EXIST
The ATM node does not exist.
11492
ATM NODE ALREADY EXISTS
The ATM node already exists.
Issue: 30-0
DN987378
397
Error messages
General Error Messages of System
11493
TEST HAS STOPPED
The mass traffic test of the call generator is not active.
11494
ANOTHER TEST IS ACTIVE
Another mass traffic test in the call generator is active.
11495
FIRST PARAMETER MESSAGE IS MISSING
The call generator has not received its first parameter
message.
11496
CLNS CANNOT BE USED FOR INITIALIZATION
The CLNS cannot be used for the initialization of ODEUPD
because it is probably locked.
11497
FLOATING TRX IS ALLOWED ONLY TO BCFS THAT
HAVE SECTORS OF ONE TRX
If a floating TRX exists in a BCF, only one normal TRX can
be created to each sector. Also, a floating TRX can only be
created to a BCF that has sectors of no more than one
TRX.
11498
BCF CAN HAVE ONLY ONE FLOATING TRX
A floating TRX can only be created if there is no previous
floating TRX in that BCF.
11499
REJECT FROM CONNECTION MANAGER IN LINE
PLUG-IN UNIT
Indicates that the connection management program block
in a cell relay line plug-in unit has rejected a service
request.
11500
UPDATE FAILED TO BOTH WDISKS
Update failed to both disks.
11501
UPDATE FAILED TO I/O UNIT W0
The update failed to I/O unit W0.
11502
UPDATE FAILED TO I/O UNIT W1
The update failed to I/O unit W1.
11503
ADMINISTRATIVE STATES OF TRXS CONTROL
CHANNELS MUST BE UNLOCKED
The requested operation was rejected due to the
administrative state(s) of the TRXs control channel(s)
being LOCKED. They must be UNLOCKED.
11504
398
EXECUTION TIME HAS EXPIRED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The execution time has already been passed.
11505
ILLEGAL DATE
The date is illegal, or the family cannot handle the date.
11506
ILLEGAL TIME
The time is illegal, or the family cannot handle the time.
11507
COMMAND FILE ALREADY EXISTS
On the disk there is already a command file with this
name.
11508
COMMAND FILE DOES NOT EXIST
There is no such command file on disk.
11509
ILLEGAL PERIOD
A period cannot be presented in this way.
11510
NO ROOM FOR NEW COMMAND
There is no room for new tasks because CTRCAL is full.
11511
NO ROOM FOR NEW OUTPUT DEVICE DECLARATION
There is no room for new output device declarations,
because NAMCAL is full.
11512
NO ROOM FOR NEW USER ID
There is no room for new user IDs because the NAMCAL
file is full.
11513
COMMAND OR PARAMETERS NOT FOUND
The command or its parameters is not found.
11514
COFFER DID NOT WAIT FOR NEW COMMAND
The waiting time for a new command has expired.
11515
COMMAND LENGTH ERROR
There is an error in the length of a command.
11516
INVALID TASK GIVEN
The requested task or command is invalid.
11517
BACKGROUND DOWNLOAD IS PREVENTED BY BCF
RESET
The BCF software handling system prevents the
background download after build attachment, if the BCF
reset is going on.
Issue: 30-0
DN987378
399
Error messages
General Error Messages of System
11518
BACKGROUND DOWNLOAD IS PREVENTED BY BCSU
OVERLOAD
The BCF software handling system prevents background
downloading because of the load rate of a signalling unit.
11519
BCF BUILD TYPE IS UNKNOWN TO BCF BUILD
HANDLING SYSTEM
The BCF build handling system does not support this build
type.
11520
FILE SIZE NOT CONSISTENT WITH MASTER FILE
INFORMATION
The physical size of an application file does not correlate
with master file information.
11521
BTS SITE TYPE AND BCF BUILD TYPE ARE
MISMATCHED
The BTS site type and BCF build type are mismatched.
11522
NO RESPONSE FROM BASE STATION
A base station did not respond during time supervision to
the task sent.
11523
BASE STATION TRANSMITTER START-UP FAILURE
AFTER BASE STATION ALARM RESET
The starting-up of a base station transmitter has failed
after a base station alarm reset.
11524
TIME OUT ON WAITING FOR INQUIRY ACK
A time out has occured when ASWMAN was waiting for an
acknowledgement message from the SWCOP unit.
11525
WRITE BUFFER GIVEN TO OCEAPI TOO SMALL
The size of the write buffer given to the OCEAPI library
program is too small to save the current CMIS primitive.
11526
PARAMETER GIVEN TO OCEAPI HAS AN ILLEGAL
VALUE
At least one parameter given to the OCEAPI library
function has an illegal value.
11527
READ ERROR IN OCEAPI LIBRARY PROGRAM
Error in reading CMIS primitive from message or memory
buffer in OCEAPI library program.
11528
400
BTS NUMBER POINTS OUT OF FILE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The BTS number is greater than the number of available
records in the parameter file of the HO/PC Algorithm.
11529
CONFLICTING ADJACENT CELL DATA BETWEEN
HO/PC ALGORITHM AND BSC DATABASE
An adjacent cell has been created into the BSC database,
but the HO/PC Algorithm is not aware of the adjacent cell.
11530
TOO MANY ADJACENT CELLS, OR BCCH ALLOCATION
LISTS RECEIVED FROM BSC DATABASE
The HO/PC algorithm receives more adjacent cells from
the BSC database than expected. Or the HO/PC algorithm
receives more BCCH allocation lists from the BSC
database than expected.
11531
PARAMETER FILES OF HO/PC ALGORITHM ARE
CORRUPTED
The parameter files of the HO/PC algorithm which include
information about the adjacent cells are corrupted.
11532
BTS WITH RF HOPPING CAN HAVE MAX 2 TRXS
There was an attempt either to create more than 2 TRXs to
a BTS that uses RF hopping, or to change a BTS that has
more than 2 TRXs to use RF hopping.
11533
CONNECTION FAILURE IN SWICOP OR NCSPRO
A connection attempt by the SWICOP or NCSPRO
program block has failed.
11534
ANCU COMMUNICATION FAILURE
A communication failure has occurred between ANCU and
OMU, or between two program blocks in ANCU.
11535
CONNECTING CIRCUIT TO TEST POINT FAILED
The set-up of a test connection has failed.
11536
RELEASING CIRCUIT FROM TEST POINT FAILED
The resetting of the test connection has failed.
11537
TEST LOOP STILL EXISTS
The test loop is still connected.
11538
TEST FRAMES RETURNED CHANGED
The test frames have returned in a changed condition.
11539
NO TEST FRAMES RETURNED
The test frames did not return.
Issue: 30-0
DN987378
401
Error messages
General Error Messages of System
11540
BASE STATION SELF TEST FAILED
The base station self test on the given base station circuit
has failed.
11541
NO FREE TSL LEFT FOR TEST CONNECTION
There is no free TSL left for connecting the given circuit to
a test point. The set-up of the test connection has failed.
11542
TEST DEVICE FOR TEST CONNECTION NOT FOUND
There is no test device for connecting the given circuit to a
test point. The set-up of the test connection has failed.
11543
TEST CONNECTION MISSING
The circuit is not connected to a test point. The
disconnection of the SPU-U has failed.
11544
SPU-U DISCONNECTED
The Signal Processing Unit SPU-U of the circuit is still
disconnected. The releasing of the circuit from the test
point has failed.
11545
COMMAND CALENDAR TASK IS BLOCKED
The calendar task is blocked either by the user with
CDCMML or by the command calendar.
11546
REMOTE MMI OPTION IS NOT IN USE IN BSC
The remote MMI option is not in use in the BSC.
11547
LOCAL COPY PARTLY SUCCESSFUL, DESTINATION
FILE FULL
The local copy service has been partly successful and the
destination file has become full.
11548
AOMPRB OR BTS SITE HAS NOT ANSWERED BCF
RESET OR CONFIGURATION REQUEST
GUPDAT has requested AOMPRB to reset the BCF, or to
configure the BTS site via the BTS O&M link. BTS or
AOMPRB have not responded to the requests within the
time limit.
11549
NO FREE INCOMING VIRTUAL PATH
No free incoming virtual path.
11550
NO FREE OUTGOING VIRTUAL PATH
No free outgoing virtual path.
11551
402
TRX IS GIVEN ON OTHER LIST
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The TRX ID list contains a TRX which is already given on
another list.
11552
CPE CALL QUEUE FULL
The queue of calls, in the calling channel, to a CPE is full.
11553
NSAP TYPE IS DIFFERENT FROM NETWORK
ADDRESS TYPE
The NSAP type is different from the network address type.
11554
NSAP IS ALREADY ATTACHED TO NETWORK
ADDRESS
There has been an attempt to attach an NSAP to a
network address, but it is already attached to the network
address.
11555
NSAP IS NOT ATTACHED TO NETWORK ADDRESS
There has been an attempt to detach an NSAP from a
network address, but the NSAP is not attached to the
network address.
11556
BACKUP CLNS NOT FOUND
No CLNS with the activity state BACKUP exists in the
OEDATA database.
11557
ROUTE EXISTS FOR CONNECTION
A route was found to exist for the broadband connection.
11558
CONNECTION EXISTS FOR BROADBAND ACCESS
A connection exists for the broadband access.
11559
CONNECTION DOES NOT EXIST FOR ACCESS
The connection does not exist for the Broadband Access.
11560
NO FREE CONNECTION INDEX AVAILABLE
Occurs when an attempt is made to reserve a connection
index from the FBBASE for an access in which all the
connection indexes are currently in use.
11561
ATM VIRTUAL PATH EXISTS
Indicates that a certain ATM virtual path already exists.
11562
ATM VIRTUAL PATH DOES NOT EXIST
Indicates that a certain ATM virtual path does not exist.
11563
Issue: 30-0
REQUEST FOR STATIC STATE INFORMATION OF
RADIO NETWORK FAILED
DN987378
403
Error messages
General Error Messages of System
Configuring the location areas has failed.
11564
RNEUPD HAS NO RESOURCES FOR REQUESTED
TASK
RNEUPD is busy. It has not finished its previous task.
11565
MAC USER LIST IS FULL
The user list of the Ethernet MAC driver program is full, so
it is not possible to add any more users to the Ethernet
plug-in unit (COCEN) in question.
11566
SERVICE ACCESS POINT LIST IS FULL
The service access point list of the Ethernet MAC driver
program is full, so it is not possible to bind any more IEEE
802.2 SAPs or Ethernet V2.0 protocol types to the
Ethernet plug-in unit (COCEN) in question.
11567
SERVICE ACCESS POINT IS ALREADY IN USE
Some MAC user has already reserved the SAP in
question. It is not allowed for two programs to use the
same Ethernet plug-in unit (COCEN) and have identical
IEEE 802.2 SAPs or Ethernet V2.0 protocol types,
because it must be possible to determine unequivocally
the receiving program when a packet is received from the
Ethernet. This is done by the Ethernet MAC driver
program, on the basis of the SAP field of the packet.
11568
SERVICE ACCESS POINT IS NOT FOUND
The service access point is not on the list of the Ethernet
MAC driver program, so it is not possible to unbind that
IEEE 802.2 SAP or Ethernet V2.0 protocol type from a
MAC user.
11569
MAC USER IS NOT FOUND
The user is not on the list of the Ethernet MAC driver
program, so it is not possible to bind or unbind an SAP
from that user, or to delete that user.
11570
LINKAGE TYPE MISMATCH
The type issued in the modify command does not match
with the type (X.25/broadcast) of the existing linkage.
11572
MAXIMUM NUMBER OF TEST GROUPS ALREADY
CREATED
The maximum number of test groups is ten. This error
code is received when the maximum is exceeded.
11573
404
NO SUCH TEST GROUP
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The routine test group was not found.
11574
TEST GROUP ALREADY CREATED
The routine test group has been defined. This error code is
received when an attempt has been made to define a
routine test group with an identifier that is in use.
11575
TEST GROUP NOT IN PROPER STATE
The routine test group was not in the proper state.
11576
ATM TRUNK ACCESS ALREADY EXISTS
The ATM trunk access already exists.
11577
A RECEIVING CHANNEL FOR TESTING IS ALREADY
ACTIVE
There has been an attempt to open a second receiving
channel for testing, although only one receiving channel is
allowed to be in testing at a time.
11578
ERRONEOUS PARAMETERS OF MODEM SIGNALLING
IN CHANNEL OPENING
The parameters of modem signalling in the channel
opening message are not correct.
11579
SENDING WAS NOT SUCCESSFUL
The sending of data was not completed without errors in
the MFST plug-in unit.
11580
OTHER TEST CONNECTION OR TEST LOOP ON
There is another test connection or test loop on the given
base station circuit.
11581
CIRCUIT GROUP RNTEST IN WRONG STATE
The channel cannot be connected to the test terminal
because the circuit group RNTEST is not in a working
state.
11583
OPERATION REJECTED DUE TO ONGOING TEST
The channel is in a test.
11584
NO FREE MESSAGE INDEX ERROR
Messages between the Cell Relay Subscriber Unit and the
Cell Relay Line Interface plug-in units are assigned a
message index. In the event that all the message indexes
are in use and it is impossible to reserve a new one, this
error code is generated.
Issue: 30-0
DN987378
405
Error messages
General Error Messages of System
11585
NO TRAFFIC ON HOME BASE STATION OF
SUBSCRIBER
The home base station of a WLL subscriber (i.e. the base
station in which the subscriber is located) is in a state in
which it is not capable of transferring terminating calls.
11586
BROADBAND SUBSCRIBER UNIT DOES NOT EXIST
The specified broadband subscriber unit was found not to
exist.
11587
BROADBAND SUBSCRIBER UNIT EXISTS
The specified broadband subscriber unit was found to
exist.
11588
HAND CREATION DID NOT SUCCEED
A master process has tried to create a hand process, but
the creation was unsuccessful.
11589
BTS ALARMS RECOVERY SEND TIMES LIMIT
EXCEEDED
BTLARM has tried to send a BTS alarm indication to
GUPDAT 60 times, but GUPDAT has not been able to
perform the task, and the recovery has failed.
11590
D-CHANNEL IS BUSY
The subscriber line is used for calls, and disconnection has
not been successful. Please use the forced test type, if you
want to test this line.
11591
FIRST DISTINCTIVE RINGING NUMBER
The first distinctive ringing number.
11592
SECOND DISTINCTIVE RINGING NUMBER
The second distinctive ringing number.
11593
THIRD DISTINCTIVE RINGING NUMBER
The third distinctive ringing number.
11594
FOURTH DISTINCTIVE RINGING NUMBER
The fourth distinctive ringing number.
11595
FIRST PARALLEL DISTINCTIVE RINGING NUMBER
The first parallel distinctive ringing number.
11596
SECOND PARALLEL DISTINCTIVE RINGING NUMBER
The second parallel distinctive ringing number.
406
DN987378
Issue: 30-0
General Error Messages of System
11597
Error messages
THIRD PARALLEL DISTINCTIVE RINGING NUMBER
The third parallel distinctive ringing number.
11598
FOURTH PARALLEL DISTINCTIVE RINGING NUMBER
The fourth parallel distinctive ringing number.
11599
FIRST RSU DISTINCTIVE RINGING NUMBER
The first RSU distinctive ringing number.
11600
SECOND RSU DISTINCTIVE RINGING NUMBER
The second RSU distinctive ringing number.
11601
THIRD RSU DISTINCTIVE RINGING NUMBER
The third RSU distinctive ringing number.
11602
FOURTH RSU DISTINCTIVE RINGING NUMBER
The fourth RSU distinctive ringing number.
11603
FIRST PARALLEL RSU DISTINCTIVE RINGING
NUMBER
The first parallel RSU distinctive ringing number.
11604
SECOND PARALLEL RSU DISTINCTIVE RINGING
NUMBER
The second parallel RSU distinctive ringing number.
11605
THIRD PARALLEL RSU DISTINCTIVE RINGING
NUMBER
The third parallel RSU distinctive ringing number.
11606
FOURTH PARALLEL RSU DISTINCTIVE RINGING
NUMBER
The fourth parallel RSU distinctive ringing number.
11607
RSU DOUBLE TELEPHONE NUMBER
RSU double subscriber number.
11608
PARALLEL RSU DOUBLE TELEPHONE NUMBER
Parallel RSU double subscriber number.
11609
DISTINCTIVE RINGING FACILITY IS ALREADY
DEFINED FOR SUBSCRIBER
Distinctive ringing has already been defined for the
subscriber.
11610
Issue: 30-0
OPENING MML SESSION FOR CALENDAR FAILED
DN987378
407
Error messages
General Error Messages of System
Opening an MML session for the command calendar has
failed. MMIMAN does not allow a session to be opened, or
it does not respond to an opening request.
11611
NSAP REFERS TO PHYSICAL CHANNEL GROUP TO
BE DELETED
The delete operation cannot be performed because there
is at least one NSAP address reference to the X.25
physical channel group to be deleted.
11612
UNKNOWN COMMAND FROM I/O MANAGER
RECEIVED
The Command Calendar Program Block (COKALE) has
received an unknown command from the I/O Manager
Program Block (IOMANA).
11613
ILLEGAL HANDLE RECEIVED IN MESSAGE
A program block cannot open a received buffer because of
an illegal handle in the buffer.
11614
DIALOG DID NOT ASK CALENDAR COMMAND
DIALOG did not ask the MML command belonging to the
task whose execution had been started, so the task was
not completed succesfully.
11615
OCEAPI SUPPORT FUNCTION FAILED
The OCEAPI support function has failed.
11616
DISTINCTIVE RINGING NUMBER ALREADY EXISTS
The distinctive ringing number already exists.
11617
DISTINCTIVE RINGING NUMBER DOES NOT EXIST
The distinctive ringing number does not exist.
11618
BCF HW DATABASE FILE TOO BIG
The size of the BCF HW database file is more than the
allowed maximum.
11619
VIRTUAL ANSWER DEVICE FACILITY IS NOT IN USE
The virtual answer device facility is not in use.
11620
MESSAGE WAITING ACTIVATION NUMBER MISSING
The activation number for the message waiting facility is
missing.
11621
408
MESSAGE WAITING PASSIVATE NUMBER IS MISSING
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The passivation number for the message waiting facility is
missing.
11622
MESSAGE WAITING NUMBERS ARE MISSING
The activation and passivation numbers for the message
waiting facility are missing.
11623
APPLICATION TYPE IS DIFFERENT FROM NETWORK
ADDRESS TYPE
The application type is different from the network address
type.
11624
ANALOGUE VOICE MAIL SUBSCRIBER
Analogue voice mail subscriber.
11625
LOCAL USER HAS OPENED SERVICE TERMINAL
SESSION
A local user has opened a service terminal session. The
remote session is prohibited during local operations.
11626
INVALID APPLICATION PARAMETERS
The contents of the application parameters are invalid,
rendering them impossible to handle.
11627
PARAMETERS CANNOT BE CHANGED
The modification of given parameters is not allowed.
11628
INVALID X.25 ADDRESS INFORMATION
The given X.25 address (SVC/PVC) information is invalid.
11629
TERMINAL HAS NO SVC CHANNELS
No SVC channels are configured to the X.25 data terminal.
11630
TERMINAL HAS NO PVC CHANNELS
No PVC channels are configured to the X.25 data terminal.
11631
INVALID VALUE FOR PVC CHANNEL
The given value may not be assigned to the PVC channel.
11633
TERMINAL HAS NO AVAILABLE PVC CHANNELS
The X.25 data terminal has no available PVC channels, all
are reserved for other users.
11634
TERMINAL HAS NO AVAILABLE SVC CHANNELS
The X.25 data terminal has no available SVC channels, all
are reserved for other users.
Issue: 30-0
DN987378
409
Error messages
General Error Messages of System
11635
WRONG TERMINAL TYPE FOR GIVEN LINKAGE
The terminal type differs from the type of linkage. The
linkage cannot be activated to a data terminal of that type.
11636
TERMINAL ALREADY HAS ACTIVE LINKAGE
There is already an active linkage in the data terminal,
which prohibits activation of the given linkage. A terminal
may have several linkages, but they must not have
identical parameters.
11637
ROLE (ES/IS) MISMATCH
The roles of the linkage and CLNS do not match.
11638
NO REASON FOR FAILURE OF OPERATION
CLNS returned no reason for the failure of the operation.
11639
ACCESS DENIED BY CLNS
CLNS denied execution of the operation.
11640
INVALID ATTRIBUTE VALUE
The given attribute value is invalid.
11641
ATTRIBUTE VALUE IS MISSING
The required attribute value is not included in the
management operation.
11642
INVALID ATTRIBUTE IDENTIFIER
The given attribute identifier is an invalid one.
11643
INVALID OBJECT CLASS IDENTIFIER
The object class identifier is invalid.
11644
PROCESSING FAILURE
An operation on the CLNS was terminated by a processing
failure.
11645
CLNS RETURNED UNKNOWN ERROR CODE
The CLNS returned an unknown error code for a failure.
11646
INVALID RANGE OF ATTRIBUTE VALUES
The range of attribute values is invalid.
11647
INVALID INSTANCE IDENTIFIER
The instance identifier of an object is invalid.
11648
410
NIGHT TRANSFER NUMBER
DN987378
Issue: 30-0
General Error Messages of System
Error messages
There has been an (illegal) attempt to remove a service
number which is also a night transfer number.
11649
OVERFLOW NUMBER
There has been an (illegal) attempt to remove a service
number which is also an overflow number.
11650
WEEKDAY RESTRICTION DOES NOT ALLOW
EXECUTION
The date and weekday combination will not allow the
execution of the task.
11651
BTS ALARM RECOVERY FAILURE DUE TO SYSTEM
RESTART
The system has been restarted by the ZUSS command,
and an ongoing BTS alarm recovery has failed due to the
restart.
11652
TERMINAL IS DISABLED
The terminal of a linkage is in a disabled state, which
prevents the activation of the linkage.
11653
ACTIVITY STATE OF CLNS IS BACKUP
The locking of a CLNS whose activity state is backup (BU)
is prohibited.
11654
ABIS O&M MESSAGE BTS_PWR_SUPPLY_CONTROL
FAILED (TIMEOUT OR NEGATIVE
ACKNOWLEDGEMENT)
BSC failed to control the TRX power supplies of a BTS
site. The scenario was interrupted.
11655
SYNTAX ERROR IN COMMAND FILE
There is a syntax error in the command file. Check the file.
11656
COMMAND NOT FOUND IN COMMAND FILE
There are no more commands in a command calendar
command file.
11657
BROADBAND LINE INTERFACE ALREADY ASSIGNED
The given broadband line interface is already assigned.
11658
LAC/CIS OF CELL REFERRED IN ADJACENT CELL
OBJECT AND TARGET CELL OBJECT ARE DIFFERENT
The LAC/CIs of the cell referred to in the adjacent cell
object and of the target cell object are different in the BSC
radio network configuration database. The conflict was
Issue: 30-0
DN987378
411
Error messages
General Error Messages of System
caused when updating the LAC and/or CI parameters of
the cell with the ZEQE command. These modifications are
not updated to the adjacent cell specifications. To correct
the adjacent cell specifications the user has to delete the
adjacent cell and then create it again.
11659
GIVEN CALENDAR TASK NOT FOUND
The given calendar task has not been found in the
calendar. Check the task identifier.
11660
DISTINCTIVE RINGING NUMBER EXISTS
There must exist no distinctive ringing numbers for a
subscriber when deleting the subscriber or the RSU
subscriber neither is it acceptable to remove distinctive
ringing facility if there are any distinctive ringing numbers
left.
11661
RECORD NUMBER OUT OF CALENDAR FILE LIMITS
There is no such record in the CTRCAL disk file.
11662
ATM STATISTICS STOPPED
The operation failed because ATM statistics has been
stopped.
11663
NOT ENOUGH TIME LEFT TO DESIRED EXECUTION
TIME
The execution time must be set at least five minutes from
the present time.
11664
ATM USER DOES NOT EXIST
The ATM user does not exist.
11665
SERVICE SET RECORD EXISTS ALREADY
A service set record with the given ID string exists already
in the trigger file.
11666
SERVICE SET RECORD DOES NOT EXIST
A service set record with the given ID string does not exist
in the trigger file.
11667
TRIGGER RECORD IS REFERRED TO
A trigger record is referred to from a service set. The
record cannot be removed before the references are
removed.
11668
412
SERVICE SET RECORD IS REFERRED TO
DN987378
Issue: 30-0
General Error Messages of System
Error messages
A service set record is referred to. The record cannot be
removed before the references are removed.
11669
SERVICE SET NAME DOES NOT EXIST
A service set record with the given name does not exist in
the trigger file.
11670
SERVICE SET DOES NOT CONTAIN ANY TRIGGERS
The service set record does not contain any references to
triggers.
11671
CUG HAS NO MEMBERS
The closed user group (CUG) has no members.
11672
CLOSED USER GROUP DOES NOT EXIST
The closed user group (CUG) does not exist.
11673
LINKAGE IS NOT ACTIVE
The linkage is not active at the moment. The reason may
be a fault in the data terminal, or in the connectionless
network service.
11674
VPI NOT FOUND
The VPI is not found.
11675
VCI NOT FOUND
The VCI is not found.
11676
LOGICAL INCONSISTENCY IN DATABASE
The database is logically inconsistent.
11677
OBJECT IS PROTECTION UNIT
The requested operation is prohibited because the object
is a protection unit.
11678
NO SUCH CROSS CONNECTION INSTANCE
The given cross connection instance does not exist.
11679
NO SUCH MULTIPOINT CROSS CONNECTION
INSTANCE
The given multipoint cross connection instance does not
exist.
11680
CLOSED USER GROUP ALREADY EXISTS
A closed user group with the given CUG interwork code
already exists.
Issue: 30-0
DN987378
413
Error messages
General Error Messages of System
11681
CUG MEMBER WITH GIVEN INDEX ALREADY EXISTS
A closed user group member with the given CUG index
already exists.
11682
ARF SUBSCRIBER NOT FOUND
The given ARF subscriber was not found.
11683
RSU NOT FOUND
The RSU data for the given ARF subscriber was not found
from the Subscriber Facility Database.
11684
DEFAULT CLOSED USER GROUP ALREADY EXISTS
The subscriber already has a default closed user group.
11685
SUBSCRIBER HAS NO CUG INDEX
There is no relation between the given subscriber and a
CUG member, or there is a relation, but the given CUG
index is incorrect.
11686
SUBSCRIBER HAS NO DEFAULT CUG
The subscriber does not have a default closed user group.
11687
FIRST MFC DIGIT NOT RECEIVED WITHIN TIME LIMIT
The MFC signalling control program has found that the first
MFC digit was not received within the time limit.
11688
SPACE BETWEEN MFC DIGITS IS TOO LONG
The MFC signalling control program has found that there
was too long a pause between two MFC digits.
11689
DIAL TONE NOT IDENTIFIED WITHIN TIME LIMIT
The MFC signalling control program has found that the dial
tone was not recognised within the time limit.
11690
IMEI COULD NOT BE OBTAINED FROM MOBILE
An inquiry to the A-interface for the IMEI of a mobile failed
because the mobile did not respond to the A-interface
inquiry.
11691
A-INTERFACE HAND PROCESS FOR THIS
CONNECTION DOES NOT EXIST
The Transaction Management Program Block identified an
A-Interface hand process that controls the connection of a
given subscriber, but the identified hand process does not
exist.
414
DN987378
Issue: 30-0
General Error Messages of System
11692
Error messages
ERROR IN SETTING CONNECTION PROTECTION
STATE
This error code is used when the state change of a
connection protection fails.
11693
NO FREE PILOT CHANNELS LEFT
All pilot channels are reserved, no free ones are left.
11694
FREEZING OF CRSU COUNTERS IN PROGRESS
The freezing of the counters of the CRSU unit is in
progress.
11695
SOME PARAMETER IS PLUG-IN UNIT SPECIFIC. ALL
SUBSC LINES OF PLUG-IN UNIT MUST BE CHANGED
Some programmable parameter of a subscriber line is
plug-in unit specific. All subscriber lines of the plug-in unit
in question must be changed at the same time.
11696
NO ACTIVE CLNS FOUND
None of the CLNS objects in the OSI database were
active.
11697
DATA TERMINAL IS LOCKED
The administrative state of a physical channel of the data
terminal is LOCKED, which prohibits the use of the
terminal.
11698
DISK COPYING ALREADY STARTED
The ASKDIS program block sends this information in a
message to the ASRPRO program block, if disk copying
has already been started when ASKDIS receives a start
disk copying message.
11699
DATA COLLECTION AFTER CRSU CHANGE IS IN
PROGRESS
Data collection from the changed CRSU unit is in progress.
11700
TOO MANY ARFCN VALUES (R1024)
The creation of range 1024 fails because there are too
many ARFCN values.
11701
ATM VP ADDRESS INVALID
The supplied ATM Virtual Path address is invalid.
11702
ATM VC ADDRESS INVALID
The supplied ATM Virtual Channel address is invalid.
Issue: 30-0
DN987378
415
Error messages
General Error Messages of System
11703
BROADBAND INTERFACE IS UNI
The broadband interface is a user-network interface.
11704
BROADBAND INTERFACE IS NNI
The broadband interface is a network node interface.
11705
BROADBAND ACCESS RATE ERROR
Error in supplied broadband access rate.
11706
FR LINK INTEGRITY TYPE UNKNOWN
Frame Relay Link Integrity Type unknown.
11707
DATABASE SYSTEM IS OVERLOADED
The transactions queue is full in the database system. New
transactions will be cancelled with this error code.
11709
ATM MEASUREMENT NAME ALREADY IN USE
The creation of an ATM measurement failed because the
measurement name is already in use.
11710
ATM MEASUREMENT OBJECT DOES NOT EXIST
The creation of an ATM measurement failed because
some of the objects to be measured do not exist.
11711
MEASUREMENT OBJECT IS NOT DESIRED TYPE
The creation of an ATM measurement failed because the
measurement object is not of the desired type.
11712
NAME TABLE IS FULL
The program block NASEVA is not capable of adding the
new service, because the name table is full.
11713
SERVICE IS DEFINED UNREPLACEABLE
The program block NASEVA is not capable of replacing the
given service, because the service has been defined
unreplaceable.
11714
SERVICE IS NOT FOUND IN NAME TABLES
The program block NASEVA is not capable of finding the
given service in the name tables.
11715
MAXIMUM NUMBER OF ATM MEASUREMENTS
ALREADY EXISTS
The creation of an ATM measurement failed because the
maximum number of the desired type of measurement
already exists.
416
DN987378
Issue: 30-0
General Error Messages of System
11716
Error messages
GENERAL SERVICE CANNOT BE UPDATED TO LOCAL
SERVICE
The program block NASEVA is not capable of updating a
general service to a local service.
11717
ATM MEASUREMENT DOES NOT EXIST
The function fails because the identified ATM
measurement does not exist.
11718
ATM MEASUREMENT ACTIVE
The function fails because the ATM measurement is active.
11719
UNKNOWN DISCONNECT REASON
The reason for the release of the OSI transport connection
is not known.
11720
TRANSPORT SERVICE USER TRANSIENTLY
UNAVAILABLE
The called transport service user is not available, but the
condition is transient.
11721
TRANSPORT SERVICE USER UNAVAILABLE
PERMANENTLY
The called transport service user is not available, and the
condition persists.
11722
TRANSPORT ADDRESS UNKNOWN
The called transport address is unknown.
11723
NORMAL DISCONNECT INVOKED BY TRANSPORT
SERVICE USER
A normal disconnection initiated by a remote Transport
Service user.
11724
REMOTE TRANSPORT ENTITY CONGESTED
The remote transport entity suffered from congestion at the
time of the connect request.
11725
CONNECTION NEGOTIATION FAILED
A connection negotiation has failed, i.e. the proposed
Transport protocol classes are not supported. This is a
persistent condition.
11726
DUPLICATE SOURCE TRANSPORT REFERENCE
A duplicate source transport reference was detected for
the same pair of NSAPs.
Issue: 30-0
DN987378
417
Error messages
General Error Messages of System
11727
MISMATCHED TRANSPORT REFERENCES
The remote transport entity specified an unknown transport
reference.
11728
TRANSPORT PROTOCOL ERROR
A transport protocol error has occurred.
11729
LENGTH INDICATOR ERROR
The header or parameter length of a Transport Protocol
Data Unit was invalid.
11730
TRANSPORT SERVICE MISBEHAVIOUR
The remote transport service provider (or user)
misbehaved by not answering a connection request within
the specified time limit.
11731
TRANSPORT REFERENCE OVERFLOW
A transport reference overflow has occurred.
11732
CONNECTION REFUSED ON NETWORK CONNECTION
A connection request has been refused on this network
connection.
11733
QOS BELOW MINIMUM
The Quality of Service was below the minimum accepted
value.
11734
ATM MEASUREMENT NOT ACTIVE
The function fails because the identified ATM
measurement is not active.
11735
MAXIMUM NUMBER OF ATM MEASUREMENTS
ALREADY ACTIVE
The activation of an ATM measurement failed because the
maximum number of measurements is already active.
11736
ANOTHER ACTIVE MEASUREMENT IS ALREADY
MEASURING OBJECT
The activation of an ATM measurement failed because the
object is already being measured by another active
measurement.
11737
ATM MEASUREMENT STOPPED BY OPERATOR
An ATM measurement is interrupted because the operator
has stopped it.
11738
418
ATM MEASUREMENT IS DELETED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The ATM measurement is deleted because its objects
were deleted.
11739
ATM MEASUREMENT DATA INVALID
ATM measurement result data is not valid.
11740
CANNOT SET/DELETE BASIC JUMPER GROUP
The routine cannot set or delete a basic jumper group. The
routine can handle only jumper groups created by the user.
11741
WARMING NOT POSSIBLE WITH FAMILY ATTRIBUTE
COMBINATION USED
Warming is not possible with the family attribute
combination used.
11742
ABIS O&M MESSAGE BTS_OUTPUT_CONTROL FAILED
(TIME-OUT OR NEGATIVE ACKNOWLEDGEMENT)
BSC failed to control the binary outputs of a BTS site.
11743
ABIS O&M MESSAGE BTS_CHA_ADM_STATE FAILED
(TIME-OUT OR NEGATIVE ACKNOWLEDGEMENT)
BSC failed to change the administrative state of a BTS
site.
11744
ABIS O&M MESSAGE BTS_RESET_REQ FAILED (TIMEOUT OR NEGATIVE ACKNOWLEDGEMENT)
BSC failed to request reset (for BCF/BTS/TRX) to a BTS
site.
11745
WRONG TYPE OF ANALYSIS TREE
The analysis tree is in other use, it can e.g. be reserved for
restriction analyses, and so other types of analysis are not
allowed in this tree, or vice versa.
11746
INVALID APPLICATION CONTEXT
The Application Context is illegal, or is not supported.
11747
SYSTEM INFORMATION MESSAGES HAVE NOT BEEN
SENT
ABIPRB has not received system information
acknowledgement messages from BTS.
11748
SERVICE HAS DIFFERENT PARAMETERS
The given service already exists, but with different
parameters.
Issue: 30-0
DN987378
419
Error messages
General Error Messages of System
11749
FREEZING OF ATM STATISTICS DISTRIBUTED PART
METERS FAILED
The freezing of the ATM statistics meters of the distributed
part failed.
11750
ATM STATISTICS METERS COLLECTION FAILED
The collecting of the ATM statistics meters from the
distributed to the centralised part failed.
11751
NO SYSTEM INFORMATION ACK MESSAGES
RECEIVED FROM LAYER 2
ABIPRB has not received system information
acknowledgement messages from layer 2.
11752
SERVICE BELONGS TO GROUP OF SERVICES
The service was found in the name table and it belongs to
a group of services. The service cannot be updated to an
individual service.
11753
SAME MEASUREMENT OBJECT IS GIVEN TWICE
The creation of a virtual traffic measurement has failed
because the same measurement object was given twice.
11754
NO RESPONCE FROM ATDSTA
The ATDSTA program block does not respond.
11755
NO ACCEPTABLE CLNS
There is no CLNS object which could be accepted by a
user. Acceptance of a CLNS requires that its operational
state is ACTIVE, its administrative state is UNLOCKED,
and its activity state is NEW.
11756
INTEGRITY KEY ERROR
The integrity key element being used is incorrect. Either
the integrity of the key element is incorrect, or the key
element is not found.
11757
INTEGRITY ERROR
The integrity of the data being handled is incorrect.
11758
CONSISTENCY ERROR
The consistency of the data being handled is incorrect.
The data differs between different storages.
11759
420
ENCRYPTION KEY ERROR
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The encryption key element being used is incorrect. Either
the integrity of the key element is incorrect, or the key
element is not found.
11760
INVALID CRYPTOGRAPHIC KEY TYPE
The type of the cryptographic key used in an operation is
invalid.
11761
INVALID DATA OBJECT IDENTIFIER
The identifier of the data object being handled is invalid.
11762
CRYPTOGRAPHIC KEY ACTIVE
The cryptographic key being handled is active.
11763
CRYPTOGRAPHIC KEY ALREADY EXISTS
The cryptographic key already exists.
11764
CRYPTOGRAPHIC KEY NOT FOUND
The cryptographic key being used is not found.
11765
CRYPTOGRAPHIC KEY NOT FOUND IN DATABASE
The cryptographic key being used is not found in the
Cryptographic Key Database.
11766
CRYPTOGRAPHIC KEY NOT FOUND IN PLUG-IN UNIT
The cryptographic key is not found in the key table of a
plug-in unit.
11767
CRYPTOGRAPHIC KEY TABLE FULL IN PLUG-IN UNIT
The cryptographic key table is full in a plug-in unit.
11768
CRYPTOGRAPHIC KEY USED IN DATABASE
The cryptographic key being handled is used in a
database.
11769
CRYPTOGRAPHIC KEY USED IN PLUG-IN UNIT
The cryptographic key being handled is used in a plug-in
unit.
11770
NO ACTIVE CRYPTOGRAPHIC KEY FOUND
No active cryptographic key is found for a key type.
11771
SEVERAL ACTIVE CRYPTOGRAPHIC KEYS FOUND
Several active cryptographic keys are found for a key type.
11772
Issue: 30-0
PHYSICAL PROTECTION FAILURE
DN987378
421
Error messages
General Error Messages of System
The physical protection of a plug-in unit is faulty.
11773
COMMUNICATION ERROR WITH PLUG-IN UNIT
An error in the communication with a plug-in unit has
occurred.
11774
ILLICIT USE OF CRYPTOGRAPHIC KEY
An illicit attempt to use a cryptographic key has been
detected.
11775
NO BCF IN MAINTENANCE MODE
There is no BCF in maintenance mode.
11776
CONFIGURATION FAILURE
Link information has not been received from the ABIPRB
program block.
11777
HASH TABLE IS FULL
There is no room for further elements in the hash table.
11778
NO ELEMENT WITH GIVEN KEY VALUE EXISTS
There is no element with the given key value in the given
hash table.
11779
THERE IS ALREADY AN ELEMENT WITH THE GIVEN
KEY VALUE IN THE HASH TABLE
The hash table has already an element with the given key
value. This error occurs only if the table has been specified
to have unique keys.
11780
PCM ALREADY IN USE
The PCM is already in use.
11781
DUPLICATE PCM
Duplicate PCM number.
11782
USER PART OF PCM NOT V5
The user part of the given PCM is not V5.
11783
VXADMI BUSY
The program block VXADMI is not capable of receiving
new tasks. Try again later.
11784
V5 INTERFACE ALREADY EXISTS
The V5 interface already exists.
422
DN987378
Issue: 30-0
General Error Messages of System
11785
Error messages
V5 INTERFACE DOES NOT EXIST
The V5 interface does not exist.
11786
VXADMI COMMUNICATION ERROR
A communication error between VXADMI and some other
program block.
11787
CLNS HAS ALREADY MAXIMUM NUMBER OF MANUAL
AREA ADDRESSES
A CLNS object already has the maximum number of
manual area addresses, so adding a new one is not
possible.
11788
CLNS HAS ALREADY MINIMUM NUMBER OF MANUAL
AREA ADDRESSES
A CLNS object already has the minimum number of
manual area addresses, so removing a manual area
address is not possible.
11789
BCF IS NOT IN MAINTENANCE MODE
The BCF is not in maintenance mode.
11790
INCORRECT INTERFACE TYPE
The type of interface is unknown, or it does not fit in the
situation.
11791
NO RESPONSE FROM CELL RELAY LINE INTERFACE
This error code indicates that there is no response from a
line plug-in unit (e.g. FRA2M) to a request message within
the designated time limit.
11792
FTAM FILE ATTRIBUTE CANNOT BE READ
A FTAM file attribute cannot be read.
11793
UPDATING FROM LOCAL TO GLOBAL SERVICE
CAUSES CONFLICT
A local service was not updated to a global service,
because a global service with the same name already
existed.
11794
FTAM NO REASON
No reason. This error is a general FTAM diagnostics
message, defined in ISO 8571-3.
11795
FTAM RESPONDER ERROR
FTAM responder error (unspecific). This error is a general
FTAM diagnostics notice, defined in ISO 8571-3.
Issue: 30-0
DN987378
423
Error messages
General Error Messages of System
11796
FTAM INITIATOR ERROR
FTAM initiator error (unspecific). This error is a general
FTAM diagnostics notice, defined in ISO 8571-3.
11797
TEMPORARY INSUFFICIENCY OF FTAM RESOURCES
A temporary insufficiency of resources. This error is a
general FTAM diagnostics notice, defined in ISO 8571-3.
11798
FTAM ACCESS REQUEST VIOLATES VFS SECURITY
A FTAM access request violates the security of the virtual
file store. This error is a general FTAM diagnostics notice,
defined in ISO 8571-3.
11800
FTAM RESPONDER TIMEOUT
The timeout expired, because the FTAM responder did not
answer. This error is a protocol and support service related
diagnostics notice, defined in ISO 8571-3.
11801
FTAM INITIATOR IDENTITY UNACCEPTABLE
The FTAM initiator identity is unacceptable. This error is an
association-related diagnostics notice, defined in ISO
8571-3.
11802
FTAM FILE NAME NOT FOUND
A FTAM file name is not found. This error is a selectionrelated diagnostics notice, defined in ISO 8571-3.
11803
FTAM INITIAL ATTRIBUTES NOT POSSIBLE
FTAM initial attributes are not possible. This error is a
selection-related diagnostics notice, defined in ISO 8571-3.
11804
FTAM FILE ALREADY EXISTS
The file already exists. This error is a selection-related
diagnostics notice, defined in ISO 8571-3.
11805
FTAM FILE CANNOT BE DELETED
The file cannot be deleted. This error is a selection-related
diagnostics notice, defined in ISO 8571-3.
11806
FTAM CONCURRENCY CONTROL NOT POSSIBLE
The FTAM concurrency control is not possible. This error is
a selection-related diagnostics notice, defined in ISO 85713.
11807
FTAM FILE IS BUSY
The FTAM file is busy. This error is a selection-related
diagnostics notice, defined in ISO 8571-3.
424
DN987378
Issue: 30-0
General Error Messages of System
11808
Error messages
FTAM FILE NOT AVAILABLE
The file is not available. This error code is a selectionrelated diagnostics notice, defined in ISO 8571-3.
11809
FTAM CREATE OVERRIDE NOT POSSIBLE
The file already exists, recreation is not possible. This error
code is a selection-related diagnostics notice, defined in
ISO 8571-3.
11811
REQUESTED FTAM ACCESS VIOLATES PERMITTED
ACTIONS
The requested FTAM access is in violation of the permitted
actions. This error code is a selection-related diagnostics
notice, defined in ISO 8571-3.
11812
FTAM ATTRIBUTE CANNOT BE CHANGED
The FTAM attribute cannot be changed. This error code is
a file management related diagnostics notice, defined in
ISO 8571-3.
11813
BAD FTAM ATTRIBUTE VALUE
Bad FTAM attribute value. This error code is a file
management related diagnostics notice, defined in ISO
8571-3.
11814
FTAM OPERATION NOT AVAILABLE
The FTAM operation not available. This error code is an
access-related diagnostics notice, defined in ISO 8571-3.
11815
FTAM OPERATION NOT SUPPORTED
The FTAM operation is not supported. This error code is an
access-related diagnostics notice, defined in ISO 8571-3.
11816
FTAM CONCURRENCY CONTROL NOT AVAILABLE
The FTAM concurrency control is not available. This error
code is an access-related diagnostics notice, defined in
ISO 8571-3.
11817
FTAM LOCAL FAILURE
FTAM local failure (unspecific). This error code is an
access-related diagnostics notice, defined in ISO 8571-3.
11818
FTAM LOCAL DEVICE FAILURE
FTAM local device failure (unspecific). This error code is
an access-related diagnostics notice, defined in ISO 85713.
Issue: 30-0
DN987378
425
Error messages
General Error Messages of System
11819
FTAM FUTURE FILE SIZE EXCEEDED
The FTAM future file size was exceeded. This error code is
an access-related diagnostics notice, defined in ISO 85713.
11820
FTAM CONTENTS TYPE INCONSISTENT
The type of the FTAM-contents is inconsistent. This error
code is a recovery-related diagnostics notice, defined in
ISO 8571-3.
11821
FUNCTIONAL UNIT NOT SUPPORTED BY FTAM
Unsupported functional unit. This error code is an
association-related diagnostics notice, defined in ISO
8571-3.
11822
UNSPECIFIC FTAM DIAGNOSTIC, RELATED TO
ASSOCIATION MANAGEMENT
Unspecific error, related to association management. This
error code is an association-related diagnostics notice,
defined in ISO 8571-3.
11823
FTAM FILE CANNOT BE CREATED
The file cannot be created. This error code is a selectionrelated diagnostics notice, defined in ISO 8571-3.
11825
FTAM OPERATION SUCCESSFUL
Successful FTAM operation.
11826
FTAM OPERATION UNSUCCESSFUL
FTAM operation unsuccessful.
11827
ERROR CODE NOT DEFINED IN FTAM
Diagnostics not relating to FTAM.
11828
NO MORE FTAM CONNECTIONS ALLOWED
No more FTAM connections allowed in the CVOPS
process.
11829
GENERIC FTAM ERROR
Generic FTAM error.
11830
FTAM PROTECTION ERROR
FTAM protection error.
11831
FTAM ASSOCIATION ERROR
FTAM association error.
426
DN987378
Issue: 30-0
General Error Messages of System
11832
Error messages
FTAM SELECTION ERROR
FTAM selection error.
11833
FTAM MANAGEMENT ERROR
FTAM management error.
11835
INVALID FTAM MESSAGE
Invalid message relating to FTAM.
11836
FTAM LOCAL FILE OPENING FAILED
OOF process failed to open a local file.
11837
CLOSING OF FTAM LOCAL FILE FAILED
OOF process failed to close a local file.
11838
FTAM FAILURE IN READING LOCAL FILE
FTAM failure in reading a local file.
11839
FTAM FAILURE IN WRITING TO LOCAL FILE
FTAM failure in writing a local file.
11840
FTAM FAILURE IN READING LOCAL FILE ATTRIBUTES
FTAM failure in reading the attributes of a local file.
11841
FTAM FAILURE IN DELETING LOCAL FILE
FTAM failure in deleting a local file.
11842
FTAM DIRECTORY LISTING FROM LOCAL VFS FAILS
FTAM directory listing from local virtual file store fails.
11843
REQUESTED FTAM FILE OPERATION IS GOING ON
The requested FTAM file operation is still going on.
11844
FTAM LOCAL FILE CANNOT BE DELETED
A local file must not be deleted.
11845
FTAM APPLICATION ENTITY TITLE NOT FOUND
The FTAM application entity title is not found.
11846
FTAM PROTOCOL PRIMITIVE OR MESSAGE NOT
ALLOWED IN THIS STATE
This FTAM protocol primitive or message is not allowed in
this state.
11847
Issue: 30-0
FTAM REMOTE ENTITY ABORTED CONNECTION
DN987378
427
Error messages
General Error Messages of System
The FTAM remote entity has aborted the connection.
11848
ABNORMAL TERMINATION OF FTAM CONNECTION
Abnormal termination of FTAM connection.
11849
OPENING OF FTAM REMOTE FILE FAILED
The opening of a FTAM remote file has failed.
11850
THIS FTAM DOCUMENT TYPE IS NOT SUPPORTED
This FTAM document type is not supported.
11851
FTAM ACCESS ERROR
FTAM access error.
11852
FTAM ACCESS REQUEST VIOLATES LOCAL SECURITY
A FTAM access request violates local security. This error
code is a general FTAM diagnostics notice, defined in ISO
8571-3.
11853
FTAM SELECTION ATTRIBUTE MISMATCH
FTAM selection attributes are not matching. This error
code is a selection-related diagnostics notice, defined in
ISO 8571-3.
11854
FTAM ACCESS CONTROL NOT AVAILABLE
FTAM access control is not available.
11855
NEGATIVE F-DATA-END INDICATION RECEIVED
The OOF process received the negative F-DATA-END
indication. The negative F-DATA-END primitive is sent by
the responder to indicate that the F-READ action was
unsuccessful. The F-DATA-END primitive relates to the
end of data transfer service, defined in ISO 8571-3.
11856
F-CANCEL INDICATION RECEIVED
The OOF process received the F-CANCEL indication. The
responder has cancelled the FTAM data transfer service by
issuing the F-CANCEL primitive. The F-CANCEL primitive
relates to the cancel data transfer service, defined in ISO
8571-3.
11857
428
NEGATIVE F-TRANSFER-END CONFIRMATION
RECEIVED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The OOF process received the negative F-TRANSFEREND confirmation. It indicates an unsuccessful completion
of a FTAM transfer. The F-TRANSFER-END primitive
relates to the end-of-transfer service defined, in ISO 85713.
11858
NEGATIVE F-CLOSE CONFIRMATION RECEIVED
The OOF process received a negative F-CLOSE
confirmation. It indicates that the action of releasing an
existing FTAM file open regime was unsuccessful. The FCLOSE primitive relates to the file close service, defined in
ISO 8571-3.
11859
NEGATIVE F-DESELECT CONFIRMATION RECEIVED
The OOF process received a negative F-DESELECT
confirmation. It indicates that the releasing of the binding
between the FTAM file select regime and the file was
unsuccessful. In spite of the negative confirmation, the
selection regime is terminated. The F-DESELECT primitive
relates to the file deselection service, defined in ISO 85713.
11860
FTAM LOCAL FILE OPERATION TIMER EXPIRED
The timer expired when an OOFTAM process was waiting
for a local file operation.
11861
PARAMETER VALUE ALREADY REQUESTED
The maintenance mode parameter value is already as
requested.
11862
INVALID TEST IDENTIFIER
An invalid scheduled test identifier has been used.
11863
TEST REPORT NOT FOUND FROM REPORT HISTORY
There was no test report available in the test report history
for the requested test object.
11864
TEST ALREADY CREATED IN BSC
The test cannot be created because it has already been
created in the BSC.
11865
PERMANENT VIRTUAL CIRCUIT BEING RESET - COTS
USER MUST WAIT
The COTS user requested a transport connection over the
X.25 PVC, although the PVC was already in use. The
COTS user should send a new transport connection
request after 180 seconds.
Issue: 30-0
DN987378
429
Error messages
General Error Messages of System
11866
PERMANENT VIRTUAL CIRCUIT STOLEN BY ANOTHER
PROCESS
Another process has established a connection over the
X.25 PVC although it had already been reserved. The old
user cannot use the connection anymore, and it should
issue an alarm if this error code is ever received.
11867
C-CHANNEL IS NOT FREE
The C-channel is not free.
11868
C2 CELL RESELECTION ACTIVE OR CBCH MOBILE
ALLOCATION OVERFLOW IN SYSINFO 4
SYSINFO 4 has no space for the C2 cell reselection
parameter because the CBCH mobile allocation list was
too large.
11869
USE OF THIS RANGE IS NOT ALLOWED
The use of this range has been barred by UTPFIL.
11870
DATABASE DOES NOT EXIST IN BTS OR IN BSC
The BTS HW database does not exist in BTS or in BSC
(no database in flash memory).
11871
NUMBER OF FUS OR CUS IS NOT CONSISTENT WITH
THW DATABASE IN SW PACKAGE
Number of frame units or carrier units is not consistent with
the hardware database which is in the BTS SW package.
11872
NUMBER OF FUS OR CUS IS NOT CONSISTENT WITH
THE HW DATABASE IN FLASH MEMORY
The number of frame units or carrier units is not consistent
with the hardware database which is in the flash memory.
11873
NUMBER OF FUS OR CUS IS NOT CONSISTENT WITH
HW DATABASE IN SW PACKAGE (NO FLASH)
The number of frame units or carrier units is not consistent
with the hardware database which is in the BTS SW
package. No flash memory.
11874
INVALID EXTENDED CELL RADIUS, OR EXTENDED
CELL FEATURE NOT IN USE IN BSC
The radius of the extended cell is invalid, or the extended
cell feature is not used in BSC.
11875
ATM MUX VP TABLE CHECK SUM ERROR
The check sums of the Virtual Path Tables in the WO and
SP sides of the ATM multiplexer do not match.
430
DN987378
Issue: 30-0
General Error Messages of System
11876
Error messages
ATM MUX VP TABLE UPDATE ERROR
The updating of the Virtual Path Tables in the WO and SP
sides of the ATM multiplexer was unsuccessful.
11877
STATISTICS INDEX ALREADY EXISTS
A statistics index for the connection already exists.
11878
NO FREE STATISTICS INDEXES AVAILABLE
All possible statistic indexes are already in use.
11879
PROTOCOL ALREADY DEFINED
The protocol is already defined.
11881
PROTOCOL DOES NOT EXIST
The protocol does not exist.
11882
D-CHANNEL SYSTEM IS NOT USED
The requested D-channel system exists, but it is not used
by any element.
11883
VIRTUAL FILE STORE MUST BE LOCAL
The given virtual file store must be local.
11884
EITHER SOURCE OR DESTINATION VIRTUAL FILE
STORE MUST BE LOCAL
Either the source or the destination virtual file store must
be local when using the FTAM copy command.
11886
NO RESPONSE FROM OOFTAM WITHIN TIME LIMIT
There is no response from OOFTAM within the time limit.
11887
NO RESPONSE FROM OVFSRP WITHIN TIME LIMIT
There is no response from the OVFSRP program block
within the time limit.
11888
NO RESPONSE FROM O7AMAN WITHIN TIME LIMIT
There is no response from the O7AMAN program block
within the time limit.
11889
LOCKING NOT ALLOWED AS OPERATIVE STATE OF
FLOATING TRX IS BL-FLO (LOCK BCF)
A floating TRX (BL-FLO) is used as BCCH TRX. Lock the
BCF so you can lock the object.
11890
Issue: 30-0
BASE BAND HOPPING NOT ALLOWED IN SECTOR
THAT HAS FLOATING TYPE TRX
DN987378
431
Error messages
General Error Messages of System
The operation is not allowed, as in the cell Base Band
hopping and the floating type of TRX are defined
simultaneously.
11891
INVALID FTAM FILESTORE PASSWORD
Invalid FTAM filestore password. This error code is an
association-related diagnostic notice, defined in ISO 85713.
11892
V5 SUBSCRIBER
This subscriber is connected to the exchange via a V5
connection.
11893
DATA LOCKED PENDING REPROVISIONING
The data has been locked, pending reprovisioning.
11894
ATTRIBUTE HAS VALUE WHICH IS OUT OF VALUE
RANGE DEFINED FOR IT
An attribute has a value, which is not one of the values
defined for it.
11895
MAXIMUM NUMBER OF V5 INTERFACE
MEASUREMENTS ALREADY EXISTS
The activation of the measurement failed because the
maximum number of V5 interface measurements is
already active.
11896
V5 INTERFACE IS ALREADY IN MEASUREMENT
The V5 interface is already being measured by another
active measurement.
11897
CELL MUST BE BARRED DUE TO BCCH TRX
FREQUENCY TYPE IS DEFINED AS SUPER-REUSED
Operation is rejected due to the configuration mismatch:
BTS parameter BAR must be Y, if FTY of the unlocked (or
to be unlocked) broadcast control channel TRX is superreused.
11898
SRM NOT UPDATED
The data of SRM was not updated.
11899
THIS FUNCTION IS NOT SUPPORTED IN THIS I/O
DEVICE
This error status is used when an I/O device cannot
execute the requested function.
11900
432
BCF HW DATABASE ADMINISTRATION PROGRAM
BLOCK (HAWADM) BUSY
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The BCF HW Database Administration Program Block
HAWADM cannot reserve new hands.
11901
INTERNAL ERROR IN BCF HW DATABASE
ADMINISTRATION PROGRAM BLOCK (HAWADM)
Operation has been interrupted by an internal error in BCF
HW Database Administration Program Block HAWADM.
11902
SIGNALLING UNIT LOAD RATE TOO HIGH
Operation has been interrupted because of too high load
rate in signalling unit (BCSU).
11903
BCF ID NOT FOUND IN HW DATABASE MANAGEMENT
SYSTEM
The BCF identity can not be found in BCF hardware
database management system.
11904
NO ACKNOWLEDGE MESSAGE TO HW DATABASE
UPLOAD/DOWNLOAD REQUEST
Acknowledge message to HW database download/upload
request from loading program block (BTDOWN) is missing.
11905
HW DATABASE UPLOAD/DOWNLOAD END MESSAGE
MISSING
The end message after HW database upload/download
from loading program block (BTDOWN) is missing.
11906
NO ACKNOWLEDGE MESSAGE FROM A-BIS O&M
PROGRAM BLOCK (AOMPRB)
A-bis O&M program block (AOMPRB) has not replied with
an acknowledge message to BCF non-volatile memory
save/erasure request.
11907
HW DATABASE OPERATION INTERRUPTED BY
VERIFICATION REQUEST FROM BCF
HW database verification request from BCF (sent during
BCF reset) has interrupted previous HW database
operation.
11908
ERROR IN SAVING HW DATABASE MANAGEMENT
FILES TO DISKS
BCF HW database management files has not been saved
to the disks on BSC. Changes made may not be updated
permanently.
11909
HW DATABASE IS ATTACHED TO BCF(S)
The HW database has attachments and therefore can not
be deleted from management system.
Issue: 30-0
DN987378
433
Error messages
General Error Messages of System
11910
HW DATABASE HAS NO ATTACHMENTS
The HW database has no attachments to BCFs.
11911
BCF HAS ALREADY AN ATTACHMENT IN PASSIVE
STATUS
New attachment is prevented because of already attached
hw database in passive status.
11912
BCF HAS NO ATTACHMENT IN PASSIVE STATUS
Passive HW database can not be activated or detachment
is not proceeded because of missing attachment in
passive status.
11913
BCF HAS NO ATTACHMENT IN ACTIVE STATUS
No HW database is attached to active status in this BCF.
11914
NO HW DATABASE FOUND IN MANAGEMENT SYSTEM
No created HW database is found in BCF HW database
management system.
11915
GIVEN DATABASES ARE OF DIFFERENT GENERATION
The generations of given databases are different and
therefore replacement is not allowed.
11916
DATABASE ID ALREADY FOUND IN MANAGEMENT
SYSTEM
The given database identity is already found in BCF HW
database management system.
11917
GIVEN FILE(S) BELONGS TO ANOTHER DATABASE
Given file(s) belongs to another already created database.
11918
LOCKING OF PHYSICAL FILE(S) INCLUDED IN
CREATED DATABASE FAILED
The physical file(s) belonging to created database are not
protected against writing and deleting.
11919
UNKNOWN HW DATABASE STATUS
The status of the HW database is unknown to
management system.
11920
ERROR IN PHYSICAL FILE INQUIRY
The BCF HW database management system has failed in
physical file inquiry and therefore database is not created.
11921
434
ERROR IN COLLECTING CONFIGURATION DATA
DN987378
Issue: 30-0
General Error Messages of System
Error messages
BCF HW database management system has failed in
collecting BCF HW database configuration data.
11922
ERROR IN COLLECTING EXISTING DATABASE
INFORMATION
BCF HW database management system has failed in
collecting information of the existing databases.
11923
ERROR IN READING BCF HW DATABASE
MANAGEMENT FILE (HDMFIL)
The reading of the file has failed.
11924
ERROR IN READING BCF HW DATABASE
CONFIGURATION FILE (HDCFIL)
The reading of the file has failed.
11925
ERROR IN WRITING BCF HW DATABASE
CONFIGURATION FILE (HDCFIL)
The writing to the file has failed.
11926
ERROR IN WRITING BCF HW DATABASE
MANAGEMENT FILE (HDMFIL)
The writing to the file has failed.
11927
RECORD NOT FOUND IN BCF HW DATABASE
MANAGEMENT FILE (HDMFIL)
The record containing wanted data was not found in file.
11928
RECORD NOT FOUND IN BCF HW DATABASE
CONFIGURATION FILE (HDCFIL)
The record containig wanted data was not found in file.
11929
BCF HW DATABASE MANAGEMENT FILE (HDMFIL)
FULL
The BCF HW database management file (HDMFIL) is full.
More databases can not be created.
11930
INTERNAL MESSAGE NUMBER FAILS
The internal check number of messages between
LOSUNGs is wrong, i.e. the check number in the reply
message is not the same as that in the request message.
11931
TIME-OUT IN LOADING
The time supervision between the LOSUNGs has expired,
i.e. the LOSSRC hand in the source computer unit has
failed to send a reply message in time to the LOSDES
hand of the target computer unit.
Issue: 30-0
DN987378
435
Error messages
General Error Messages of System
11932
WRONG LOADING SOURCE
In his loading request message the user has indicated a
wrong loading source in the source computer unit.
11933
TIME-OUT ON SOURCE UNIT
The transfer of the load module has failed because the
time allotted for the source computer unit has expired.
11934
DIFFERENT PACKAGE ID
When loading, it was discovered in the source computer
unit that the source and target computer units have
different package identifiers, i.e. that they have different
packages.
11935
LOADING NOT ALLOWED
Loading from one computer unit to another is not allowed,
because the units have different new_pack or trial
statuses.
11936
LOADING IS GOING ON
The process requesting loading is already undergoing
loading.
11937
NO RIGHTS TO REMOVE
The process attempting to remove the load module does
not have the rights to do so.
11938
NO MODULE TO REMOVE
There is no load module of that name to be removed.
11939
LOADING TIME-OUT
The loading of the load module was not successful in the
time alloted.
11940
WRONG VALUE OF
NEIGH_CELL_RANGE_LIMITS_PRM_C PARAMETER
The value of the neigh_cell_range_limits_prm_c parameter
is wrong. The value must be between 0..7.
11941
PARAMETER DEFINITION NOT FOUND
The parameter definition is not found from the KADATA
database.
11942
COMMAND CASES NOT FOUND
The command cases not found from the KADATA
database.
436
DN987378
Issue: 30-0
General Error Messages of System
11943
Error messages
BLOCK NOT FOUND
The block of the command is not found from the KADATA
database.
11944
PARAMETER RANGE NOT FOUND
The range for the parameter is not found from the KADATA
database.
11945
EXECUTION PRINT-OUT NOT FOUND
The execution print-out of the command is not found from
the KADATA database.
11946
PARAMETER VALUE NOT FOUND
The parameter value is not found from the KIDATA
database.
11947
SERVICE NOT FOUND
The service is not found from the KIDATA database.
11948
POINT NOT FOUND
The point is not found from the KIDATA database.
11949
SUBSCRIBER NOT FOUND
The subscriber is not found from the KIDATA database.
11950
SERVICE ALREADY EXISTS
The service already exists in the KIDATA database.
11951
POINT ALREADY EXISTS
The point already exists in the KIDATA database.
11952
SERVICE HAS SUBSCRIBERS
The service has subscribers and they have to be deleted
before the service can be deleted.
11953
RADIUS EXTENSION FEATURE IS NOT IN USE IN BSC
This error code informs operator that this feature is not
available.
11954
NO ACKNOWLEDGE MESSAGE TO BCF RESET
REQUEST
Acknowledge message to BCF reset request from
BTLARM program block is missing.
11955
Issue: 30-0
DATABASE ID NOT FOUND
DN987378
437
Error messages
General Error Messages of System
The database identity is not found in BCF HW database
management system.
11956
PHYSICAL FILE(S) NOT DELETED
BCF HW database management system has failed in
deleting physical database file(s) from the fixed disks of
the BSC.
11957
OPERATION NOT SUCCEEDED ON BOTH DISKS
The BCF HW database operation has not succeeded on
the both fixed disks in BSC.
11958
BCF AND DATABASE OF DIFFERENT GENERATIONS
The generations of the BCF and the HW database are
different.
11959
HW DATABASE IN MANAGEMENT SYSTEM DIFFERS
FROM HW DATABASE IN BCF
The active HW database attached to BCF in management
system is different from the database in BCF.
11960
PROCESS IS TOO BUSY TO EXECUTE REQUEST
The process is unable to carry out the requested job as it
is already working on an unfinished job.
11961
HAND DESTROYS ITSELF
The hand destroys itself by giving the STOP command,
because it cannot perform initialisations.
11962
NO SPACE FOR LOAD MODULE
There is no space in the target computer unit for the load
module to be loaded.
11963
NO ROOM FOR LOAD MODULE
There is insufficient buffer space in the source computer
unit for the load module to be moved to the target
computer unit.
11964
LOAD MODULE NOT OK
There is an error in the load module: either the structure or
the check sum is incorrect.
11965
SUCH MODULE NOT LOADABLE
A load module of the given name was not found in the
memory of the source computer unit.
11966
438
UNIMPLEMENTED INSTRUCTION
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The service interpreter tries to execute an unimplemented
instruction.
11967
UNDEFINED INSTRUCTION
The service interpreter has detected an undefined
instruction code.
11968
DATABASE ERROR
Error in database operation.
11969
ASSIGNMENT MISMATCH ERROR
Datatype mismatch error in assignment statement.
11970
NO ROOM IN BOOKKEEPING TABLE
There is no room in bookkeeping for the information of the
load module to be loaded.
11971
GUIDANCE STRING EXCEEDS ITS MAXIMUM LENGTH
A string formed for guidance purposes exceeds its
possible maximum length.
11972
RANGE DEFINITIONS INCORRECT IN KADATA
DATABASE
The KADATA database is incorrect on what concerns
range definitions.
11973
KADATA HAS INCORRECTLY CODED PARAMETERS IN
EXECUTION DEFINITIONS
In KADATA, execution definitions do not match the
parameters.
11974
KADATA EXECUTION DEFINITION INCORRECT,
UNKNOWN TRANSACTION CALLED
The KADATA execution definitions include a call for an
unknown transaction.
11975
USER HAS NOT SUFFICIENT RIGHTS TO EXECUTE
COMMAND
The user has not sufficient rights to execute the command.
11976
NO RESOURCE FOR REQUEST
There are insufficient resources for requesting the data of
the load module. There is not enough space either for the
bookkeeping copy or for the request record.
11977
Issue: 30-0
REQUESTING NOT GOING ON
DN987378
439
Error messages
General Error Messages of System
The using process has sent a follow-up request message,
even though requesting has not even started yet.
11978
KADATA INCORRECT, PARAMETER IS OF AN
UNKNOWN TYPE
KADATA has an incorrectly defined parameter type.
11979
SUCH REQUESTING NOT GOING ON
The using process has sent a follow-up request message,
but its type is wrong, i.e. the user has initiated a request,
but the follow-up request is of another type.
11980
KAISER FAILS TO RESERVE HAND
KAISER is unsuccessful in hand reservation.
11981
GIVEN ASCII CHARACTER CANNOT BE TRANSLATED
INTO A NUMERIC VALUE
The given ASCII character cannot form a numeric value.
11982
TRANSLATION TO NUMERIC VALUE PRODUCES TOO
BIG A VALUE
The translation to a numeric value produces a result that
does not fit in the range given for that constant.
11983
TRANSLATION TO NUMERIC UNSUCCESSFUL,
FORMAT ERROR
The given ASCII string cannot be translated into a numeric
value because of a format error in the string.
11984
SIGNALLING LINK(S) CANNOT BE TRANSFERRED TO
BACK-UP PCM
The back-up PCM for an active signalling link does not
exist. A possible state change to the PCM concerned may
block the active signalling link.
11985
TRANSFERRING OF SIGNALLING LINK(S) TO BACK-UP
PCM POSSIBLE
A back-up PCM for the active signalling link exists. A state
change to the PCM concerned will not block the active
signalling link.
11986
RESTART OF THIS PREPROCESSOR UNIT IS NOT
DECLARED
The preprocessor unit is not declared to be restartable.
11987
PARALLEL RECOVERY JOB IS NOT ACCEPTED
A parallel recovery action is not accepted for execution.
440
DN987378
Issue: 30-0
General Error Messages of System
11988
Error messages
PARALLEL RECOVERY JOBS BY VARIOUS MML
COMMANDS NOT ACCEPTED
MML commands from different terminals cannot be used to
activate parallel recovery actions.
11989
PARALLEL RECOVERY JOB TO BE ACCEPTED BY
USER APPROVAL
The parallel recovery action will be accepted for execution
only at the users own risk. Acceptance will require the
approval of the user.
11990
UNFINISHED HW DATABASE OPERATION IN BCF
There is an unfinished BCF HW database handling
operation in BSC and no new operation can be begun.
11991
PARAMETER VALUE ALREADY EXISTS
The parameter value already exists in the KIDATA
database.
11992
PARAMETER STORAGE ERROR
Erroneous parameter storage in database
KADATA/KIDATA.
11993
FEATURE IS NOT IN USE
Requested optional feature is not available.
11994
THERE IS NO SUCH FILE BASENAME IN VIPARA
METOCH cant find in VIPARA the file basename used in
primitive.
11995
THE INFORMATION IN THE FILESPEC(S) IS
INCORRECT
Erroneous information in the list of filespecs.
11996
THE PROCESSING OF THE OCH TAKES TOO MUCH
TIME
Processing of the OCH takes too much time as result of
erroneous execution.
11997
FILE HANDLING FAILED
File handling failed.
11998
TTTCOF UPDATING FAILED
VIDAST failed to update TTTCOF file.
11999
Issue: 30-0
DECIMAL POSITION NUMBER RESERVED
DN987378
441
Error messages
General Error Messages of System
The Decimal Position number (DP) given is already
reserved.
12000
L3 ADDRESS RESERVED
The L3 address is already used by another subscriber in
the same V5 interface.
12001
CHAINED CELLS IN RAPID FIELD DROP OPTION IS
NOT IN USE IN BSC
The chained cells in rapid field drop is not supported in the
BSC.
12002
OPTION OPTIMIZATION OF MS POWER LEVEL IN
HANDOVER NOT IN USE IN BSC
Optimization of the MS power level in handover is not
supported in BSC.
12003
CUG HAS ALREADY BEEN DEFINED TO SUBSCRIBER
Closed User Group has already been specified to
subscriber
12004
SUBSCRIBER HAS CUG INTERLOCK CODE
Subscriber has been already defined CUG interlock code.
12005
SUBSCRIBER HAS TOO MANY CUGS PROVISIONED
Mobile subcriber has too many CUGs.
12006
CUG INDEX ALREADY DEFINED TO SUBSCRIBER
Cug-index had been already defined to subscriber.
12007
ILLEGAL BS GROUP GIVEN
You have used basic service group code which has been
defined as illegal for this particular operation.
12008
GIVEN BASIC SERVICE GROUP NOT FOUND
Provisioning of CUG supplementary service has been
attempted to basic service group which subscriber does
not have.
12009
INTRA CUG PARAMETERS CONFLICT
When ocb has been defined to a CUG , the same CUG
cannot been defined as a preferential CUG.
12010
PREFERENTIAL CUG HAS NOT BEEN FOUND
Preferential CUG must be found amongst the CUGs given
to a subscriber.
442
DN987378
Issue: 30-0
General Error Messages of System
12011
Error messages
OBJECT CLASS IS NOT SUPPORTED
The given object class is not supported by the local agent.
12012
LOADING PROGRAM BLOCK (BTDOWN) NOT READY
FOR SERVICE REQUESTS
Loading program block (BTDOWN) is in start state and
does not accept service requests.
12013
AUDIT NOT COMPLETED NORMALLY
V5.2 BCC protocol, AUDIT procedure, incomplete normal.
12014
ACCESS NETWORK FAULT
V5.2 BCC protocol, AUDIT procedure, connection
incomplete, access network fault.
12015
USER PORT NOT PROVISIONED
V5.2 BCC protocol, AUDIT procedure, connection
incomplete, user port not provisioned.
12016
INVALID V5 TIME SLOT
V5.2 BCC protocol, AUDIT procedure, connection
incomplete, invalid V5 time slot identification.
12017
INVALID V5 2048 KBIT/S LINK
V5.2 BCC protocol, AUDIT procedure, connection
incomplete, invalid V5 2048 kbit/s link identification.
12018
TIME SLOT IS PHYSICAL C-CHANNEL
V5.2 BCC protocol AUDIT procedure, connection
incomplete, time slot being used as physical C-channel.
12019
PARAMETER TABLE WAS NOT DEFINED
The parameter table is not defined in the subscriber
database.
12020
INTEGRITY CHECKING OF DATABASE FILE
INTERRUPTED
The integrity checking of a database file has been
interrupted in order to avoid overflow in the report file.
12021
HW DATABASE IDS SAME IN REPLACE
The BCF HW database to be replaced is same as the
replacing HW database.
12022
Issue: 30-0
DATA OBJECT TRANSLATION IN PROGRESS
DN987378
443
Error messages
General Error Messages of System
The data object, e.g. a database or a file, is being
translated. The updates to this data object are forbidden
during the translation.
12023
TIME-OUT IN FIRST DATA
The preprocessor did not receive the first message in time.
12024
NEW PEELNK NOT FOUND FROM APPLICATION
PACKAGE
The preprocessor cannot find the new PEELNK from the
application package.
12025
INVALID APPLICATION PACKAGE LENGTH IN HEADER
The length of the application package, indicated in the
header of the message, is not correct.
12026
PREPROCESSOR PACKET NAME ID OFFSET IS
INVALID
The offset of the packet name ID is not correct. The name
ID offset is located in the header of the message.
12027
PREPROCESSOR PACKET CODE OFFSET IS INVALID
The code offset of an application package is not correct.
The code offset is located in the header of the application
package.
12028
INVALID PREPROCESSOR PACKET LOADING PLACE
The loading place of the application package is not correct.
The loading place is located in the header of the package.
12029
PREPROCESSOR FIRST DATA MESSAGE IS TOO
SHORT
The first data message received is too short. The
preprocessor cannot decompress it correctly.
12030
PREPROCESSOR FLASH ERASING FAILURE
The preprocessor cannot erase the FLASH memory. This
is a fatal error, because it is impossible to write a new
application package in FLASH if it cannot be erased.
12031
PREPROCESSOR FLASH WRITING FAILURE
The preprocessor cannot write to the FLASH memory. The
error is fatal, because the new application package cannot
be programmed in FLASH.
12032
444
UNKNOWN MESSAGE TO PREPROCESSOR
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The preprocessor does not recognise the message,
because it is somehow messed up.
12033
PREPROCESSOR PROTOCOL ERROR IN FIRST DATA
There is some kind of protocol error in the first received
data message. Maybe the message received is not the
one it should be.
12034
PREPROCESSOR PROTOCOL ERROR IN REST OF
DATA
There is a protocol error in the rest of the data messages.
Maybe the preprocessor was waiting for the rest of the
data messages and it received the last data message.
12035
REJECT CAUSE: UNSPECIFIED
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
unspecified rejection.
12036
REJECT CAUSE: ACCESS NETWORK FAULT
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
access network fault.
12037
REJECT CAUSE: ACCESS NETWORK BLOCKED
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
access network blocked (internally).
12038
REJECT CAUSE: CONNECTION ALREADY AT PSTN
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
connection already present at the PSTN user port to a
different V5 time slot.
12039
REJECT CAUSE: CONNECTION ALREADY AT V5 TIME
SLOT
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
connection already present at the V5 time slot(s) to a
different port, or to a ISDN user port time slot.
12040
REJECT CAUSE: CONNECTION ALREADY AT ISDN
PORT
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
a connection already present at the ISDN user port time
slot(s) to a different V5 time slot(s).
12041
REJECT CAUSE: USER PORT UNAVAILABLE
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
user port unavailable (blocked).
Issue: 30-0
DN987378
445
Error messages
General Error Messages of System
12042
REJECT CAUSE: DEALLOCATION ERROR,
INCOMPATIBLE DATA
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
deallocation cannot be completed due to incompatible data
content.
12043
REJECT CAUSE: DEALLOCATION ERROR,
INCOMPATIBLE V5 TIME SLOT
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
deallocation cannot be completed due to V5 time slot(s)
data incompatibility.
12044
REJECT CAUSE: DEALLOCATION ERROR,
INCOMPATIBLE PORT DATA
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
deallocation cannot be completed due to port data
incompatibility.
12045
REJECT CAUSE: DEALLOCATION ERROR,
INCOMPATIBLE TIME SLOT DATA
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
deallocation cannot be completed due to user port time
slot(s) data incompatibility.
12046
REJECT CAUSE: USER PORT NOT PROVISIONED
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
user port not provisioned.
12047
REJECT CAUSE: INVALID V5 TIME SLOT
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
invalid V5 time slot identification(s).
12048
REJECT CAUSE: INVALID V5 2048 KBIT/S LINK
V.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
invalid V5 2048 kbit/s link identification.
12049
REJECT CAUSE: INVALID USER PORT TIME SLOT
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
invalid user port time slot(s) identification(s).
12050
REJECT CAUSE: V5 TIME SLOT USED AS C-CHANNEL
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
V5 time slot(s) being used as physical C-channel(s).
12051
REJECT CAUSE: V5 LINK UNAVAILABLE
V5.2 BCC protocol ALLOCATE/DEALLOCATE procedure,
V5 link unavailable (blocked).
446
DN987378
Issue: 30-0
General Error Messages of System
12052
Error messages
V5FPST FILE IS FULL
The V5FPST file is full.
12053
AS7 RESOURCE NOT AVAILABLE FOR ADDING NEW
V5 ISDN USER PORT
The operation is not possible due to a lack of AS7
resources.
12054
INVALID SIGNALLING TYPE
The signalling type is incorrect.
12055
PLUG-IN UNIT MEMORY CHECKSUM ERROR
The checksum of a memory area in a plug-in unit is
incorrect. The calculated checksum differs from the
checksum stored in the plug-in unit.
12056
INVALID TEST OBJECT
Test object was not found or its value was incorrect.
12057
SUB TEST OBJECTS FOUND UNDER THE MAIN TEST
OBJECT
Main test object cant be deleted because there were found
sub test objects under the main test object.
12058
INVALID MODIFICATION REQUEST
Requested modification cant be done.
12059
UNDERLAYOVERLAY STATISTICS OPTION IS NOT IN
USE IN BSC
This error code informs operator that this feature is not
available.
12060
RNOS USAGE OPTION IS NOT IN USE IN BSC
This error code informs operator that this feature is not
available.
12061
INCOMPATIBLE CARD TYPE
The card type is incorrect.
12062
THERE IS NO ANALYSIS FOR THE CARRIER ACCESS
CODE IN THE CAC IDENTIFICATION ANALYSIS
A Carrier Access Code is added to a B-number, but it is
not defined in the CAC Identification Analysis.
12063
Issue: 30-0
CARRIER ACCESS CODE GIVEN BY CARRIER
ACCESS CODE CHANGE ANALYSIS IS TOO LONG
DN987378
447
Error messages
General Error Messages of System
A Carrier Access Code given by the Carrier Access Code
change analysis is longer than the exchange is able to
handle.
12064
C-CHANNEL DOES NOT EXIST
The C-channel does not exist.
12065
DELETION OF C-CHANNEL IS NOT ALLOWED
The deletion of the C-channel is not allowed.
12066
SERVICE REQUEST LOG IS NOT IN USE
The application does not use the Service Request Log.
12067
ATM MEASUREMENT OBJECT IS DELETED
An ATM measurement object is deleted while the
measurement is active.
12068
MEASUREMENT TIME LIMIT HAS BEEN EXCEEDED
The measurement is deleted because the time limit for the
measurement hand has expired.
12069
LOGICAL C-CHANNEL NUMBER ALREADY EXISTS
The logical C-channel number already exists.
12070
CROSS CONNECTION IN TEST STATE
The error code is set when xc is in test and there is an
attempt to carry out a forbidden operation on the xc, e.g. it
is forbidden to delete xc while it is in test state.
12071
TRANSACTION LOG FAILURE
The storing of the back-up mark into the database
transaction log is unsuccessful.
12072
DATABASE BACK-UP IS IN PROGRESS
The database back-up is in progress when a new back-up
request is sent.
12073
EVENT LOG STREAM NOT FOUND
The given event log stream is not found from the ELSPAR
file.
12074
MAX EVENT LOG STREAMS IN UNIT
The maximum number of event log streams in the
computer unit has been reached.
12075
448
EVENT LOG STREAM IS IN USE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Application(s) is (are) connected to the given event log
stream.
12076
EVENT LOG APPLICATION NOT FOUND
The given event log application is not found from the
EFCONF file.
12077
BUFFER COUNT LIMIT OF ELGSTR IS REACHED
The number of buffers allocated by ELGSTR has reached
the maximum. No new buffers can be allocated before an
allocated buffer is written to disk. If the last buffer becomes
full, then new events are lost.
12078
ALLOCATION OF NEW BUFFER IN ELGSTR HAS
FAILED
ELGSTR tried to allocate a new buffer, but an operating
system routine returned an error status. If the currently
used buffer becomes full, new events are lost.
12079
ELGDSK DID NOT ATTACH BUFFER
In reply to its disk save message ELGSTR has received a
message indicating that ELGDSK did not attach the buffer
to be saved. All events in the buffer are lost.
12080
OPERATION CANCELLED
The requested operation was cancelled due to an MCANCEL-GET request.
12081
MAX EVENT LOG APPLICATIONS
The number of applications using the event log has
reached its maximum.
12082
MMI-RESOURCE ALLOCATION TIME-OUT
MMI-resource allocation timer expired.
12083
NOT ENOUGH SPACE FOR TEST OBJECTS
Requested test objects cannot be defined for test because
there is not enough space for them.
12084
V5 LINK ID ALREADY EXISTS
The V5 interface link identifier already exists.
12085
COAFIL IS FULL
COAFIL is full.
12086
UNIT IS SPECIFIED EARLIER IN COAFIL
The unit is already in the COAFIL file.
Issue: 30-0
DN987378
449
Error messages
General Error Messages of System
12087
UNIT IS NOT SPECIFIED IN COAFIL
The unit is not found in the COAFIL file.
12089
NO ANSWER FROM VARATM
The VARATM program block has not answered within time
supervision.
12090
NO ANSWER FROM PXNETM FOR V5 SUBSCRIBER
DATA MODIFYING REQUEST
PXNETM has not acknowledged a V5 subscriber
information modifying request within the time limit to
V5MANA.
12091
DECIMAL AREA RESERVED FOR THIS V5 INTERFACE
IS FULL
The decimal area for this V5 interface must be enlarged.
12092
ET UNIT IS NOT IN TEST STATE
The exchange terminal is not in the test state. E.g.
diagnostics and test functions (line loopback) cannot be
performed in states other than TE-EX.
12093
NO WORKING SECMO PLUG-IN UNIT FOUND
No working SECMO plug-in unit is found in the computer
unit. The requested service cannot be provided.
12094
REQUESTED OPERATION DOES NOT BELONG TO
THOSE AVAILABLE FOR OBJECT
The requested CMISE operation is not available for the
target object.
12095
RAM MEMORY OF PLUG-IN UNIT FAULTY
The RAM memory of the plug-in unit is faulty.
12096
I/O MEMORY OF PLUG-IN UNIT FAULTY
The I/O memory of the plug-in unit is faulty.
12097
BCC ALLOCATION ERROR IN AN
BCC allocation error in access network.
12098
BCC DEALLOCATION ERROR IN AN
BCC deallocation error in access network.
12099
BCC HAND CREATION ERROR IN AN
BCC hand creation error in access network.
450
DN987378
Issue: 30-0
General Error Messages of System
12100
Error messages
BCCPRB DOES NOT ANSWER
BCCPRB fails to answer within predefined time limit.
12101
BCC PROTOCOL ERROR
BCC protocol error in communication with access network.
12102
CONGESTION ON ROUTE
Congestion on given route.
12103
V5 SEMIPERMANENT CONNECTION ALREADY
DEFINED
The given connection is already created.
12104
V5 SEMIPERMANENT CONNECTION DISTURBED
A V5 semipermanent connection is defined but disturbed.
12105
V5 SEMIPERMANENT CONNECTION NOT DEFINED
V5 semipermanent connection not defined.
12106
BAD V5 SEMIPERMANENT CONNECTION
INFORMATION
Bad information or message when creating V5
semipermanent connection.
12107
V5 SEMIPERMANENT CONNECTION FAILED IN
SWICOP
The creation of a V5 semipermanent connection failed in
SWICOP.
12108
NO ROUTE TO GIVEN SUBSCRIBER FOUND
No route to subscriber.
12109
SPVSEM DOES NOT ANSWER
The supervision of the V5 semipermanent connections has
not started: SPVSEM does not answer.
12110
V5 SEMIPERMANENT CONNECTION SUPERVISION
ERROR IN AN
The supervision of a V5 semipermanent connection does
not start/stop.
12111
SSU NOT DEFINED OR NOT IN USE
SSU is not defined or is not in use.
12112
SWICOP DOES NOT ANSWER
SWICOP did not answer within the predefined time limit.
Issue: 30-0
DN987378
451
Error messages
General Error Messages of System
12113
VXADMI DOES NOT ANSWER
VXADMI did not answer within the predefined time limit.
12114
VSEPRB WORK FILE READ ERROR
VSEPRB work file read error.
12118
OBJECT NOT CREATED
The object has not been created.
12133
MAXIMUM NUMBER OF V5 INTERFACE
MEASUREMENTS
Number of V5 interfaces in measurement is already at its
maximum.
12134
UNBLOCKING UNSUCCESSFUL
The unblocking of the V5 interface did not succeed.
12135
V5 PORT BLOCKING TIME-OUT
A V5 port has been blocked longer than the allowed time.
12136
CORRESPONDING BCF IS IN WRONG STATE FOR THE
OPERATION
The corresponding BCF is not in the proper state for the
operation.
12137
CELL IS IN MINIMUM CONFIGURATION
The cell is in minimum configuration due to clock failure.
This means that only the BCCH-TRX is available.
12138
C-CHANNEL CREATION NOT ALLOWED
The creation of the C-channel is not allowed.
12139
TOO MANY TRXS DEFINED IN CELL IN NONSYNCHRONISED SITE
If a base station is non-synchronous, only 1 TRX is
allowed in a cell.
12140
NON-BCCH TRX UNLOCK NOT ALLOWED IN NONSYNCHRONOUS SITE
Non-BCCH TRX unlocking is not allowed in a nonsynchronous base station.
12141
SUBSCRIBER IS VIRTUAL SUBSCRIBER
The given subscriber exists but not in this HLR.
12142
452
LINKS ARE NOT IN SAME UNIT
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Links are not in same unit. Check if DCS is already used
by other unit.
12143
NO COLLECTIONS IN DATABASE
There are no collections in the database.
12144
UNKNOWN COLLECTION NAME
The name of the collection is unknown.
12145
NO DIRECTORIES IN DATABASE
There are no directories in the database.
12146
UNKNOWN DIRECTORY NAME
The directory name given in the command cannot be
found.
12147
NO DIRECTORIES FOR THIS COLLECTION
The collection defined has no directories.
12148
INCORRECT TARGET TYPE
The interrogation can be executed only if the target type is
defined as a collection (target_type_t_coll) or as empty
(target_type_t_none).
12149
NO RELATIONS IN DATABASE
There are no relations in the database.
12150
UNKNOWN RELATION NAME
The name of the relation is unknown.
12151
COLLECTION DEFINED HAS NO RELATIONS
The collection defined has no relations.
12152
NO COMPUTATIONAL RELATIONSHIPS IN DATABASE
There are no computational relationships in the database.
12153
UNKNOWN NAME OF COMPUTATIONAL
RELATIONSHIP
The name given for the computational relationship does
not exist.
12154
NO COMPUTATIONAL RELATIONSHIPS FOR GIVEN
COLLECTION
There are no computational relationships for the collection
defined.
Issue: 30-0
DN987378
453
Error messages
General Error Messages of System
12155
UNKNOWN TARGET TYPE
The target type is unknown.
12156
DIFFERENT ARITY IN TUPLE AND RELATION
The tuple arity used differs from the arity of the
corresponding relation.
12157
TUPLE OF COMPUTATIONAL RELATIONSHIP MUST
HAVE THREE VALUES
The tuple used for the computational relationships must
have three values.
12158
TIME-OUT ON QUERY
The query time expired and the query was cancelled.
12159
QUERY COMPLETE
The query has been completed.
12160
POINT ITEM NOT FOUND
The point item cannot be found in the KIDATA database.
12163
VARIABLE DOES NOT EXIST
The given variable does not exist
12164
ADJACENCY ALREADY EXISTS IN DATABASE
There already is an adjacency for this linkage in the
OEDATA database.
12165
CREATION OF ADJACENCY IN DATABASE FAILED
The creation of a new adjacency in the OEDATA database
has failed.
12166
ADJACENCY DOES NOT EXIST IN DATABASE
The adjacency does not exist in the OEDATA database.
12167
CODE BLOCK NOT FOUND
The code block cannot be found in the KIDATA database.
12168
TIMERS FOR ALL USERS HAVE EXPIRED
Timers for all users of the ATM measurement have
expired.
12169
IDENTIFIER LENGTH MUST BE EVEN
The identifier must consist of an even number of
characters.
454
DN987378
Issue: 30-0
General Error Messages of System
12170
Error messages
TRX SOFTWARE DOWNLOADING STARTED
The operation is rejected because the downloading of the
TRX software had started. The operation can be attempted
again after a while.
12171
TRX SOFTWARE DOWNLOADING IN PROCESS
The operation is rejected due to the fact that the TRX
software is being downloaded. Try the operation again
after a while.
12172
STATE OF INTERFACE INCORRECT
The state of the interface is unknown or otherwise unfit for
the situation.
12173
MORE DATA AVAILABLE
More data records are available.
12174
TOO MANY FREQUENCIES PER BTS IN CASE OF RF
HOPPING
Maximum number of frequencies per site has been
exceeded in case of RF hopping.
12175
BTS HAS DETECTED MISMATCH BETWEEN CA AND
MA
BTS has detected inconsistency between CA and MA.
12176
OUTGOING BUFFER OF ASWI IN ASM IS NOT EMPTY
The outgoing cell buffer must be empty during ASM
switchover.
12177
ALL RECEIVING CHANNELS ARE ALREADY IN USE
The time slot of the MFST plug-in unit is free, but all the
receiving channels of the current function are already in
use. The signalling type used requires a free receiving
channel before the service can be provided.
12178
V5 INTERFACE TYPE IS 30B+D
The V5.2 interface is of type 30B+D.
12179
INCORRECT V5 INTERFACE TYPE
The type of V5 interface used is incorrect: e.g. type V5.1 is
used when V5.2 30B+D should be used.
12180
POWER LEVEL CAN NOT BE USED IN THE TEST
Power level cannot be used in the test.
12181
Issue: 30-0
TIMEOUT IN RECEIVING TEST RESULT FROM DSP
DN987378
455
Error messages
General Error Messages of System
Timeout in receiving test result from DSP.
12182
TEST RESULT INVALID
Test result invalid (divide by zero not allowed in BER/FER
calculation).
12183
BER/FER OUT OF RANGE
BER/FER out of range.
12184
ANTENNA TEST IS NOT SUPPORTED DUE TO
EXTERNAL ANTENNA
Antenna test is not supported due to external antenna.
12189
V2 SUBSCRIBER LINE MEASUREMENTS NOT
POSSIBLE
Measurements of subscriber lines connected via the V2
interface are not possible in this exhange.
12200
PDN CONTEXT ALREADY EXISTS
A PDN Context with the given context ID already exists.
12201
PDN CONTEXT LIMIT EXCEEDED
Subscriber already has the maximum possible number of
PDN contexts.
12202
COMMAND PARTLY SUCCESSFUL: MME NOT
UPDATED
The data cannot be transferred to MME correctly. The
Diameter interface rejects the given operation. However,
the data has been stored in the HLR database.
12203
PDN CONTEXT DOES NOT EXIST
PDN context is not found from the subscriber in hostel
database.
12204
THE DEFAULT PDN CONTEXT CANNOT BE DELETED
PDN context is not found from the subscriber in hostel
database.
12205
THE GIVEN TARGET MME IS NOT ACTIVE
Connection to the given MME does not exist.
12206
A PREVIOUS LTE RESTORATION IS ONGOING
A previous LTE restoration operation is still running.
12207
456
EPS DATA ALREADY EXISTS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
By EPS data creation, subscriber already has existing EPS
data.
12208
EPS DATA DOES NOT EXIST
By EPS data update or interrogation, the required EPS
data does not exist.
12209
EUTRAN ACCESS NOT ALLOWED
E-UTRAN access for subscriber is not allowed.
12210
MME ADDRESS DOES NOT EXIST
The required MME address does not exist.
12230
NO FREE KEY VERSION FOUND
No free version of the given key type was found.
12231
HANDLING OF OMXFIL FAILED
The handling of the OMXFIL file failed, probably due to a
failure in the operating system routine.
12232
LINKAGE HAS MAXIMUM NUMBER OF ADJACENCIES
The creation of the manual adjacency failed because there
already is a maximum number of adjacencies in the
linkage.
12233
SNPA ADDRESS OF MANUAL ADJACENCY IS MISSING
The SNPA address of the manual adjacency is missing.
12234
MANUAL ADJACENCY IS NOT ACTIVE
The manual adjacency is not active, i.e. it is not connected
to the ODEUPD program block.
12239
SYNCHRONIZATION TO EXTERNAL SOURCE FAILED
Synchronization to external source failed. BTS is
synchronized to its internal clock.
12240
FATAL SYNCHRONIZATION FAILURE
Synchronization failed either to internal or external source.
BTS is not synchronized to its internal clock.
12241
BTS DOES NOT SUPPORT HALF RATE CHANNELS
BTS does not support half rate channels.
12242
Issue: 30-0
CANNOT OUTPUT METER NAMES ON DISK
DN987378
457
Error messages
General Error Messages of System
The creation of measurement failed, because meter
names cannot be output on disk. If you want to use the
meter names, use the operation & maintenance unit or the
logical file as an output device.
12243
CHANGEOVER OF ACTIVE MAINTENANCE
COMPUTER IN PROGRESS
Another computer is taking over the functions of the active
maintenance computer.
12244
EXCLUSIVE RECOVERY ACTION IN PROGRESS
The recovery action in progress does not allow other
simultaneous recovery actions.
12245
REQUESTED RECOVERY ACTION IS EXCLUSIVE
The recovery action that is requested excludes other
simultaneous recovery actions.
12246
RECOVERY ACTION IN PROGRESS IN ACTIVE
MAINTENANCE COMPUTER
The recovery action that is requested cannot be performed
because a recovery action is in progress in the active
maintenance computer.
12247
RECOVERY ACTION IN PROGRESS IN THIS UNIT
TYPE
A recovery action is already in progress in another unit of
this type.
12248
RECOVERY AUTOMATONS RESERVED
Recovery automatons are reserved for other recovery
actions.
12249
UNIT RESTART FAILED.
Unit restart which was activated by routine test failed.
12250
NOT-IN-USE TYPE RADIO TIMESLOTS (RTSL) HAVE TO
BE LOCKED
The unlocking of a TRX is allowed only if the not-in-use
type of channels are in the locked state.
12251
INCORRECT PACKET IDENTIFICATION
The packet identification which is derived during initial
loading from another unit or from the BOTTOM table in the
memory is not identical with the data on the disk.
12252
458
INCOMPATIBLE DATA AND TYPE FORMAT
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The type of data is incompatible with the given type format.
12253
SIZE OF DATA AND TYPE FORMAT INCOMPATIBLE
The size of the data is not compatible with the given type
format.
12254
TOO MUCH DATA WRITTEN FOR ARRAY
There is too much written data to fit in the array.
12255
BLOCKING OF V5 USER PORT IS NOT POSSIBLE
The blocking of a V5 user port is not possible.
12256
TSL RESERVED
The TSL is already reserved.
12257
ONLY ONE LINK PER DPNSS PCM ALLOWED
The operator can create only one link per DPNSS PCM.
12258
CIRCUIT GROUP IS NOT MEMBER OF GIVEN CUG
Circuit group is a member of a closed user group, but is
NOT a member of the given closed user group. For
example: There could be an attempt to remove a circuit
group from a given closed user group when that circuit
group is not a member of the given closed user group, but
is a member of some other closed user group.
12259
SYNTAX ERROR IN DATA TYPE FORMAT
There is a syntax error in the data type format.
12260
NOT-IN-USE TYPE OF RADIO TIMESLOTS (RTSL) HAVE
TO BE UNLOCKED
The unlocking of a TRX is allowed only if the not-in-use
type of channels are in the unlocked state.
12261
NAME OF EXCLUSIVE COLLECTION MISSING
The name of the exclusive collection must be given when it
is used in the search tuple for the relations.
12262
NO ROWS CORRESPONDING TO GIVEN TUPLE
No rows corresponding to the given search tuple could be
found in the relation or in the computational relationship.
12263
GIVEN COLLECTION IS EMPTY
The collection defined is empty.
12264
Issue: 30-0
OBJECT INDEX UNKNOWN IN COLLECTION
DN987378
459
Error messages
General Error Messages of System
No object with the given index can be found in the
collection.
12265
READING OF DDL-TEXTS FROM DISK FILE FAILED
The reading of the DDL-texts from the disk file failed.
12266
RELATION IS EMPTY
The relation is empty.
12268
SEARCH KEY IS TOO LONG
The search key used is too long.
12269
SEARCH KEY IS TOO SHORT
The search key used is too short.
12270
COMPUTATIONAL RELATIONSHIP IS EMPTY
The computational relationship defined is empty.
12271
GIVEN DIRECTORY IS EMPTY
The directory is empty.
12272
TOO MUCH DATA FOR VARIABLE
The object has too much data to fit into the variable
reserved for it.
12273
COUNT OF SUBSLOTS FOR SIGNALLING DIFFERS
FROM OTHER TRXS OF THE CELL
Every TRX in the cell must have same count of subslots
reserved for signalling.
12274
VLR PARTLY UPDATED
VLR has not accepted all service data sent by HLR. It
returns services which are not accepted in ACK message
even though all service data is stored into HLR database.
12275
INTEGRITY CHECKING OF DATABASE IS ALREADY IN
PROGRESS
Integrity checking of the requested database is already in
progress. This error message is also given when the
operator has requested a checking of a disk database, but
a checking of another disk database is in progress.
12276
TIME-OUT ON CHECKING DATABASE INTEGRITY
Time-out on checking database integrity.
12277
460
UNKNOWN FREQUENCY BAND
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Frequency band was not GSM or DCS.
12278
SUBSCRIBER PORTED
A subscriber has been ported.
12279
FR USERS IN SAME PIU
The creation of the frame relay (FR) measurement failed
because there are two users on the same plug-in unit.
12280
VARIABLE ALREADY EXISTS
The variable name already exists.
12281
NOT ENOUGH SPACE ALLOCATED
There is not enough space allocated for the variable to
store the required amount of data.
12282
CREATION OR DELETION OF SMUX CIRCUITS FAILED
Smux circuits couldnt be created or deleted. Given ETPCM is not on Abis interface or given circuits are already
in use. See computer log for more information.
12283
TOO MANY CHANNELS UNDER 386-BCSU
Because of limited memory capacity of BCSU having 386
processor the number of channels which is reserved for
the BCSU is limited. This limit can be exceeded when new
TRX is created or channel types of existing TRX are
modified.
12284
AUTOMATIC RETURN NOT ALLOWED: WRONG
RETURN CASE
You are trying to allow automatic return from or to a
package wich is not active.
12285
AUTOMATIC RETURN NOT ALLOWED BECUASE IT IS
NOT IN USE
This error has occurred because you are trying to allow
automatic return when it has not been implemented in the
program block BOLERO.
12286
AUTOMATIC RETURN NOT ALLOWED: OMU DOUBLED
Automatic return is not allowed when OMU is doubled.
12287
ANOTHER AUTOMATIC RETURN ALLOWED
This automatic return cannot be allowed because another
automatic return is already allowed.
12288
Issue: 30-0
AUTOMATIC RETURN ALREADY ALLOWED
DN987378
461
Error messages
General Error Messages of System
This automatic return is already allowed.
12289
AUTOMATIC RETURN NOT ALLOWED: PACKAGE
MISSING
Automatic return cannot be allowed; you are trying to allow
automatic return from or to a package which is missing.
12290
DISK FAILURE
Automatic return is not allowed because of disk failure.
12292
RETURN NOT DISALLOWED: NO AUTOMATIC RETURN
ALLOWED
You cannot disallow automatic return when no automatic
return has been allowed.
12293
RETURN NOT DISALLOWED: THE AUTOMATIC
RETURN IS NOT ALLOWED
Automatic return cannot be disallowed because this
automatic return is not allowed while another type of
automatic return is allowed.
12294
HALFRATE OPTION IS NOT IN USE IN BSC
Halfrate option is not in use in BSC.
12295
MULTIBAND OPTION IS NOT IN USE IN BSC
Multiband option determines if both, single band and
multiband mobiles can have adjacent cells from both GSM
and DCS bands.
12296
INCORRECT STATUS OF DESTINATION PACKAGE
The status of the destination package must be BU
(backup) or NW (new) when a change delivery is installed.
Changes should not be installed on packages with status
FB (fallback) or UT (untitled).
12297
TWO PACKAGES ALREADY EXIST IN DISK
DIRECTORY
Installation of the change delivery to the software package
failed because two packages already exist in the directory.
There can be a maximum of two packages per disk
directory, and this installation would result in a third one.
12298
CANNOT WRITE FILE TO DISK
The writing of a file to the fixed disk failed when installing
the change delivery.
12299
462
NEW LOAD MODULE INFORMATION DOES NOT
MATCH WITH CFLIST
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The new information in the load module header does not
tally with the information in the CFLIST file: either the
delivery is faulty or the copying of the delivery to the fixed
disk failed.
12300
NON-DEFAULT LOAD MODULE ALREADY EXIST IN
DESTINATION DIRECTORY
Change delivery cannot be installed because a non-default
load module already exists in the final destination directory
(for example BLCODE or LFILES). Each directory can
contain only two load modules with an identical name.
12301
COPYING ERROR WHEN INSTALLING MODULES
FROM CDTEMP TO FINAL DIRECTORY
An error has occurred when copying the load modules of
the change delivery from the CDTEMP temporary directory
to the final directory. The error may be caused by a
hardware fault or a full disk.
12302
LOAD MODULE SPECIFIED IN NEW MAFILE DOES NOT
EXIST IN DESTINATION PACKAGE
The load module specified in the new MAFILE file of the
change delivery does not exist in the destination package.
The load module should be found in the destination
package if it is not included in the change delivery. The
installation failed, possibly because the change delivery is
erroneously built or the destination package is faulty.
12303
DATA OF DELETABLE LOAD MODULE DOES NOT
MATCH WITH CFLIST
The deletion of the load module in the change delivery
failed because the identification data of the load module
does not match with the data in the CFLIST file. Thus the
load module cannot be removed without a possible loss of
data; the module may belong to another change delivery or
a base delivery.
12304
DELETION OF LOAD MODULE FAILED WHEN
REMOVING CHANGE DELIVERY
The load module could not be deleted when removing the
change delivery, possibly due to a hardware error.
12305
UNABLE TO WRITE HIFILE TO DISK WHEN DELETING
CHANGE DELIVERY
The information on HIFILE file could not be written to disk
while deleting the change delivery. The disk may be full.
Error is returned from IFOLIB library.
12306
Issue: 30-0
CANNOT READ HIFILE WHEN INTERROGATING
CHANGE NOTES
DN987378
463
Error messages
General Error Messages of System
The HIFILE file cannot be read when interrogating the
history information in the change notes. The error is
returned from DMXRTE or IOFLIB library.
12307
CANNOT READ CFLIST WHEN READING CONTENTS
OF CHANGE DELIVERY
CFLIST file cannot be read while interrogating the
information on the change delivery. The error is returned
from DMXRTE or IOFLIB library.
12308
INCORRECT STRUCTURE OF FILE NAME/NUMBER
CONVERSION TABLE
The structure of the File Name/Number Conversion Table
(MEFILE) is incorrect.
12309
SERVICE NUMBER IDENTIFIER ALREADY RESERVED
The identifier of the service number to be created is
already reserved.
12310
EXECUTION OF THE GENERIC MML-COMMAND
TAKES TOO LONG
The execution of the generic MML-command takes an
exceptionally long time.
12311
UNFINISHED CONNECTION TO TRX EXISTS
New connection cannot be established because there is
already unfinished operation in this TRX.
12312
TRX NUMBER MISSING
The user has given Remote MMI connection request
without TRX number in case of DE45/DF45.
12313
INTELLIGENT UNDERLAY-OVERLAY OPTION IS NOT IN
USE IN BSC
Intelligent underlay-overlay is designed to allow operator to
reuse frequencies more intensively and hence achieve
higher radio network capacity.
12314
ZERO DATA LENGTH
Attempted to use a zero data length.
12315
ZERO NAME LENGTH
Attempted to use a variable name with zero length.
12316
INVALID SESSION VARIABLE NAME
The session variable name is invalid.
464
DN987378
Issue: 30-0
General Error Messages of System
12317
Error messages
TIME-OUT ON INTERROGATION OF V5 INTERFACE
TYPE
You have interrogated the VXADMI program block about
the V5 interface type (V5.1 or V5.2) by using the V5
interface id, but the inquiry has expired due to time
supervision.
12318
V5 INTERFACE TYPE IS NEITHER V5.1 NOR V5.2
You have interrogated the VXADMI program block about
the V5 interface type by using a V5 interface id, but the
interface type is unknown to VXADMI.
12319
REPEATED INTERRUPTIONS ON SUPERVISED
SEMIPERMANENT CONNECTION
An interruption on the supervised semipermanent
connection has been detected and connection successfully
re-established, but the connection is still faulty during the
following supervision period.
12320
THE SUBSCRIBER OF V5.2 INTERFACE DOES NOT
EXIST UNDER SPVSEM SUPERVISION
The SPVSEM program block cannot find the V5.2
subscriber that was requested from the work file.
12321
NO RESPONSE TO THE INQUIRY OF V5.2
SEMIPERMANENT CONNECTION
Data on semipermanent V5.2 subscriber connection has
been inquired from the VSEPRB program but there is no
response during time supervision.
12322
ERROR IN CREATION OF HAND PROCESS
The BCCPRB program block has detected an error in the
creation of the hand process.
12323
NO ANSWER FROM AN TO AUDIT DESPITE
RETRANSMISSION
No answer is received from the Access Node (AN) despite
retransmission of the AUDIT message.
12324
PROTOCOL ERROR IN MESSAGE FROM ACCESS
NODE
A protocol error has been detected in the message
received from the Access Node.
12325
SEMIPERMANENT CONNECTION RECOVERY HAS
FAILED
The recovery of the semi permanent re-connection has
expired due to time supervision.
Issue: 30-0
DN987378
465
Error messages
General Error Messages of System
12326
NO ANSWER FROM ACCESS NODE DESPITE
RETRANSMISSION OF ALLOCATION MESSAGE
No answer is received from the Access Node despite
retransmission of the ALLOCATION message.
12327
HLR NOT UPDATED
HLR update failed.
12328
TOO MANY DUAL ARFCN VALUES
The creation of neighbour cell description fails because
there are too many DUAL ARFCN values.
12329
CREATION OF CONNECTION FAILED ON START-UP
A V5 semipermanent connection was defined, but its
creation failed on start-up of VSEPRB.
12330
LAST OBJECT ID IS SMALLER THAN FIRST OBJECT ID
IN SEARCH TUPLE
The identifier of the last object in the search tuple is
smaller than that of the first object.
12331
NO SUCH LOADING IDENTIFIER
The virtual loading using the given loading identifier does
not exist.
12332
FAST MOVING MS OPTION IS NOT IN USE IN BSC
Fast moving handheld mobile stations handling in macro
cells. If MS connected through macro cell is detected as
slow moving MS, then it will be handed over to suitable
underlying micro cell.
12333
NO FREE A-INTERFACE PCMS IN BCSU
Maximum number of A interface PCMs controlled by one
BCSU exceeded.
12334
A-INTERFACE ET-PCM NOT FOUND
Given PCM is not A interface ET-PCM.
12335
ABIS INTERFACE ET-PCM NOT FOUND
Given PCM is not Abis interface ET-PCM.
12336
SMUX PLUG-IN UNITS NOT EQUIPPED
SMUX plug-in units have not been equipped in both
MCMUs.
12337
466
IDENTIFICATION OF CHANGE DELIVERY AND ACTIVE
PACKAGE IDENTICAL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The identification data of the change delivery may not be
identical with that in the directory of the active package
when installing the change delivery.
12338
CFLIST OF THIS NAME CANNOT BE FOUND IN
SOURCE DIRECTORY
No CFLIST file with the given name can be found in source
directory. The file name must be identical with the name
that is used in the change delivery.
12339
CHANGE DELIVERY WITH THIS NAME IS ALREADY
INSTALLED
The installation failed because a change delivery carrying
the given name has already been installed in this package.
It is not possible to install a change delivery with a similar
name twice. If the installation has terminated, you must
first remove the change delivery and then install it again.
12340
CHANGE DELIVERY IDENTIFICATION OF NEW MAFILE
DOES NOT MATCH WITH THAT GIVEN AS PARAMETER
The identification of the change delivery in the new
MAFILE file does not match with the identification given as
a parameter. If a new MAFILE is included in the change
delivery, its change delivery identification must be identical
with that of the change delivery to be installed.
12341
NO CFLIST FILE IN PACKAGE DIRECTORY
There must be a CFLIST file in the ASWDIR directory
before the change delivery can be removed.
12342
CHANGE DELIVERY ID IN MAFILE DOES NOT MATCH
WITH THAT GIVEN AS PARAMETER
The identification of the change delivery in the non-default
MAFILE file must be identical with the identification to be
removed, i.e. the identification given as a parameter.
12343
THE DATABASE OCCURRENCE IS ERRONEOUS
The given database occurrence does not exist in DBPARA
or own unit is used as occurrence type when it has not
been defined.
12344
TRX MAY HAVE MAXIMUM TWO RTSLS CARRYING
SDCCH SUBCHANNELS
It is possible to define maximum two RTSLs for TRX
carrying SDCCH subchannels.
12345
Issue: 30-0
MAXIMUM NUMBER OF VARIABLES STORED
DN987378
467
Error messages
General Error Messages of System
A maximum number of variables has been exceeded and
thus a new one cannot be stored.
12346
TOO MANY SIMULTANEOUS OPERATIONS
A maximum number of simultaneous, parallel operations
have been exceeded. Wait until resources are free and try
again.
12347
FAULTY CHANGE PERCENTAGE IN CHARGING
The given change percentage causes an error for one of
the following reasons: (1) the decrease is over 100% (2)
the increase makes the pulse train exceed its maximum
value (3) the increase makes the charge rate fall below its
minimum rate (4) the decrease makes the charge rate
exceed its maximum value.
12348
ATTRIBUTE RECORD ALREADY EXISTS
The number of the attribute record already exists.
12349
UNKNOWN ATTRIBUTE RECORD
This attribute record does not exist.
12352
ATTRIBUTE RECORD HAS REFERENCES
Reference is made to this attribute record from a combined
attribute or from an external file.
12353
ERROR IN EVENT LOG CONTINUITY
The stream of events in the event log is not continuous.
12354
SUBSLOTS RESERVED FOR SIGNALLING MAY NOT
CONTAIN TRAFFIC TYPE RTSLS
TRX RTSL configuration is illegal if subslots reserved for
signalling contain traffic RTSLs (RTSL types TCHF, TCHH
or TCHD).
12355
GROUP SWITCH TYPE ILLEGAL FOR HALF RATE
RTSLS
Half Rate RTSLs require group switch type to be GSWB.
12356
CONTROL TYPE RTSLS NOT ALLOWED FOR
FLOATING TRX
Only RTSL types TCHF, TCHH, TCHD and NOTUSED are
allowed for floating TRX.
12357
468
ILLEGAL RECORD STATE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
You were trying to change the state of a non-bitmapped
record file; the only record state that can be given as a
parameter for this type of file is record_state_t_update_c.
12358
CREATION OF REPORT FILE UNSUCCESSFUL
Signalled when report text file cannot be created to disk or
creation of corresponding logical file failed. Log file of
appropriate computer unit should be inspected for further
information.
12359
UNKNOWN SIGNALLING LINK
The given signalling link does not exist.
12360
UNKNOWN TYPE OF NETWORK
The type of network defined does not exist.
12361
UNKNOWN SIGNALLING POINT
The signalling point does not exists.
12362
SUBSYSTEM UNKNOWN
The subsystem does not exist.
12363
ILLEGAL STATE OF CHANGE NOTE OF CHANGE
DELIVERY
You cannot remove a change delivery which has a change
note in active or created state.
12364
CANNOT OPEN SOURCE FILE
Source file opening fails. This can be due to incorrect file
(and/or) path name, bad IO-unit name or error in file open
operation. Most likely incorrect file name.
12365
CANNOT OPEN DESTINATION FILE
Destination file opening failed. There may be incorrect file
name, for example non-existing directory path or incorrect
IO-unit name. If file name is correct, this error code can
mean that writing to directory is not allowed. Another
cause is error in file open operation.
12366
ERROR IN FILE READING
File reading failed. More information can be read from
error/test log files. Compression is not interrupted
immediately after error in file reading (in order to avoid
increasing algorithm complexity).
12367
Issue: 30-0
ERROR IN FILE WRITING
DN987378
469
Error messages
General Error Messages of System
Writing to destination file failed. Exceeding predefined
destination file size is most likely reason to cause this
error. More accurate information about error can be read
from log file. Notice that compression is not interrupted
immediately after file write error.
12368
SOURCE FILE IS TOO SMALL, COMPRESSION IS NOT
STARTED
Size of source file is too small. Compression is not done, if
size is smaller than 20 blocks (one block equals to 512
bytes, so limit size is about 10 kB).
12369
NO FREE HAND PROCESS TO DO THE JOB
There were no free hand process(es) to do the task.
12370
RENAME FAILED AFTER SUCCESSFUL
COMPRESSION
During compression destination file has temporary name.
Temporary file name is same as real one, except that
extension in temp. file is .TZ and .Z in real destination file.
If this error status appears, the compression has
succeeded, but renaming after compression failed for
some reason. So the .TZ -file can be used.
12371
REQUESTED OPERATION HAS NOT BEEN
IMPLEMENTED YET
Operation that user requested in compression service
request message has not been implemented yet.
12372
UNDEFINED ERROR CODE
Undefined error during compression. Very unlikely to
appear.
12373
REQUESTED TEST NOT SUPPORTED BY THE
DEFINED SITE TYPE
Requested test is not possible with defined site type.
12374
C-CHANNEL HAS SUBSCRIBERS
The C-channel has subscribers.
12375
TOO MANY DISK VERSIONS OF LOAD MODULE IN
DISK DIRECTORY
There are more than two disk versions of the load module
in the disk directory when only two can be handled: the
active version and the non-active version. Check why there
are too many versions on disk.
12376
470
INVALID VERSION HANDLING REQUESTED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The version handling that was requested is invalid.
12377
FILE VERSION LIMIT REACHED
No new versions of the file can be created, as the
maximum number of versions allowed are already in use.
12378
V5 INTERFACE HAS SUBSCRIBERS
The V5 interface has subscribers.
12380
PAGE WHICH CAUSED THE PAGE FAULT IS PRESENT
The PAGLIB library generates this error when the page
fault handler detects that the page which caused the page
fault is present.
12381
ADDRESS OUTSIDE PHYSICAL RAM
An attempt was made to access an address which is
outside the physical RAM area and not visible in any linear
window.
12382
PAGE TABLE ENTRY INVALID
The page cannot be fetched because there is invalid
information in the page table entry.
12383
PAGING IS NOT IN USE
This service can be used only when paging is in use.
12384
PAGING HAS ALREADY BEEN INITIALIZED
Paging has already been initialized, i.e. paging is set either
to be used or not, and it cannot be re-initialized.
12385
AREA OF VIRTUAL MOVE OUTSIDE DRAM
Virtual move failed because the area defined (source
and/or destination) lies outside the scope of the physical
DRAM.
12386
ALL PAGES ARE NOT PRESENT
One or several of the pages defined are not present.
12387
AT LEAST ONE PAGE IS ALREADY PRESENT
One or more of the memory pages are already present.
12388
AT LEAST ONE OF THE PAGES IS LOCKED
One or more of the memory pages is locked.
12389
PAGING HANDLER HAS NOT BEEN REGISTERED
The paging handler has not been identified.
Issue: 30-0
DN987378
471
Error messages
General Error Messages of System
12390
PAGING MEMORY AREA DOES NOT EXIST
The given paging memory area has not been set as nonpresent, or all its pages have become present and the
information concerning the area has been destroyed.
12391
MEMORY AREA DOES NOT START AT PAGE
BOUNDARY
The memory area concerned does not start at page
boundary.
12392
PAGES ARE OUTSIDE THE MEMORY AREA
One or more of the pages is outside the boundaries of the
given memory area.
12393
INCORRECT LENGTH OR STARTING POINT OF
MEMORY
The given memory area is currently registered with a
different starting address or length information.
12394
INVALID PARAMETERS
One or more of the parameters of the service routine call
are invalid.
12395
PAGE GROUP SIZE IS INVALID
The size of the page group is invalid.
12396
PAGLIB FULL
The service cannot be provided because the internal
structure of the PAGLIB library does not allow any more
data.
12397
ACCESS DENIED TO GIVEN PHYSICAL MEMORY
AREA
The given area in the physical memory contains paging
data structures and thus it cannot be mapped to a linear
window.
12398
ILLEGAL LINEAR WINDOW SIZE
The size given for the linear window is invalid; it must not
be 0.
12399
TSL HAS SUBSCRIBERS
The time slot has subscribers.
12400
LOAD DESTINATION LIST FULL
The load destination list of the PFMEMF program block is
full.
472
DN987378
Issue: 30-0
General Error Messages of System
12401
Error messages
VIRTUAL LOADING LIST FULL
The virtual loading list of the PFMEMF program block is
full.
12402
TIMEOUT ON PAGE WAITING
The missing page of the memory file has not arrived in
time.
12403
INCORRECT VALUE RANGE FOR PARAMETERS
The range of values defined for the two parameters on the
same loop level do not match.
12404
RESERVED FOR OPERATOR SERVICES
The subscriber cannot be deleted and the subscriber
position number cannot be changed if the given position
number is reserved for operator services.
12405
DECIMAL POSITION AREA WAS NOT FOUND
The decimal position area that was given could not be
found in the subscriber database.
12406
DECIMAL POSITION AREA IS NOT FREE
The decimal position area that you were trying to reserve
in the subscriber database is already at least partly
reserved.
12407
NO SUCH V5 SUBSCRIBER
There is no V5 subscriber of the given type in the
subscriber database.
12408
SUBSCRIBER CONNECTED TO INTERFACE
THE INTERFACE CANNOT BE REMOVED BECAUSE
THERE IS A SUBSCRIBER CONNECTEDTO IT.
12409
TARIFF NOT ACCEPTED IN ORIGINATING OR
INTERWORKING EXCHANGE
The originating exchange or the interworking exchange
does not accept the tariff sent with the CHG-message
(ISUP2).
12410
TARIFF NOT ACCEPTED IN TRANSIT EXCHANGE
The transit exchange does not accept the tariff sent with
the CHG-message (ISUP2).
12411
TARIFF NOT WITHIN LIMITS
The tariff is not within the given limits.
Issue: 30-0
DN987378
473
Error messages
General Error Messages of System
12412
MAXIMUM TARIFF AMOUNT EXCEEDED
The amount of tariffs exceeds the maximum amount
allowed (6).
12413
NO RESPONSE TO CHG MESSAGE
No response (CHGA) is received to the CHG-message
which has been sent.
12414
INCORRECT TARIFF FORMAT
Pulse charging has been given as the tariff format, but this
format cannot be sent in the CHG-message (ISUP2).
12416
CONVERSION OF TARIFF IS NOT POSSIBLE
It is not possible to convert the tariff into pulse charging:
the given tariff is either too high or too low for the pulses to
be generated.
12417
TARIFF RECEIVED ABOVE CHARGING POINT
The tariff is received from an outgoing circuit although the
own exchange should be the charging point used and
charging from above this charging point (e.g. outgoing line)
cannot be accepted.
12418
INCORRECT EVENT SIZE
The size of the event in the event log is incorrect.
12419
NO TRXS UNDER BCF
DE45/DF45 type BCF sites cannot be unlocked if there are
no TRXs created under BCF.
12420
OAM LINK OUT OF ORDER
O&M link is down.
12421
DEFINED MASTER CLOCK TRX DOES NOT EXIST
If DE45/DF45 type BCF site is defined to be synchronized,
defined Master Clock TRX must exist under BCF.
12422
ATTRIBUTE CONTENT DOES NOT MATCH WITH GIVEN
DATA
The Match has given a negative result to the evaluation of
the attribute against the data of the call.
12423
NON-DEFAULT DISK VERSION OF MAFILE ALREADY
EXISTS IN DISK DIRECTORY
Change delivery cannot be installed if the disk directory
already contains a non-default version of MAFILE file. This
installation would create a new MAFILE or copies of a
474
DN987378
Issue: 30-0
General Error Messages of System
Error messages
possible new MAFILE from the change delivery to the
destination directory. It is likely that a previous change
delivery is installed into the package but has not been
taken into use.
12424
CHANGE DELIVERY ID IN CFLIST FILE AND FILE NAME
DO NOT MATCH
There is a mismatch between the identification used in the
CFLIST fileof the change delivery the name of the file.
They must be identical.
12425
NO SUCH CONVERSION PROGRAM
Requested conversion program cannot be found. Check
name and path of conversion program. Check if PEXHAN
and/or CNVFAM should support this conversion program.
12426
OBJECT INSTANCE DOES NOT EXIST
The CMISE service primitive contains an object instance
that was not found in the MIB (Managed Information Base)
of the network element.
12427
OBJECT INSTANCE CONTAINS SUB-INSTANCES
The given object instance given in the delete CMISE
service primitive contains sub-instances in the MIB
(Managed Information Base) of the network element, and
the deletion of such object instances is not allowed.
12428
LOAD MODULE OF CHANGE DELIVERY TO BE
DELETED IS ACTIVE
The deletion of the change delivery failed, because a load
module which is identical with the CFLIST file is active on
disk. It is likely that the change delivery to be deleted is in
use.
12429
NO ANSWER FROM MEMDAT
A disk updating was requested from MEMDAT, but it does
not answer.
12430
SRMEAS IS BUSY, NO UPDATES ALLOWED
SRMEAS is busy and will not allow updates now. Please
wait a few minutes and try again.
12431
AT155 -CONNECTION INDEX FOR FRAME RELAY FULL
No free connection indices could be found in the space
reserved for the fra2m/AT34 connections of the AT155
cards in the connection index.
12432
Issue: 30-0
AT155 CONNECTION INDEX FOR AT34 CONNECTIONS
FULL
DN987378
475
Error messages
General Error Messages of System
No free connection indices could be found in the space
reserved for the fra2m/AT34 connections of the AT155cards.
12433
LOADING FAILED: UNEQUAL DATA LENGTH
The file cannot be loaded, because the length of data in
the source and destination file are not equal. The
difference may be in the load module, header, bitmap or
data.
12434
UNCONTROLLED CHANGE OF DEFAULT PACKAGE
The software package has been changed to another one
by automatic return due to an error during the previous
restart of the OMU.
12435
SYSTEM RESTART WHILE OMU NOT IN TRIAL
The system has been restarted while the undoubled OMU
was not set in trial configuration.
12436
INCORRECT CONTENT IN RECORD
The content of the record is, at least partly, incorrect; i.e.
the record does not contain the information it should.
12437
INCORRECT RECORD TYPE
The record is not of a type that is allowed. The type used
may not exist or no reference is allowed to this record type.
12438
PARSING OF THE LOGICAL EXPRESSION FAILED
The parsing of the logical expression failed because the
given expression is not in line with the syntax.
12439
CONTROLLED EXIT FROM OCH
The operations of the OCH have been interrupted in a
controlled manner, i.e. the MAOPRB program block has
interrupted the current operation, but no error message
has been sent to the CMIP interface.
12440
CALL COMPLETION TO BUSY SUBSCRIBER
The subscriber type is Call Completion to Busy Subscriber
(CCBS).
12441
DIFFERENCE IN RECORD- OR BYTE STRING LIST IN
SOURCE AND DESTINATION
The given lists are different in length: the number of
records in the record lists of the source and destination are
different, or the number of byte strings in the byte string list
vary, or the pair of byte strings (source - destination) differ
in length.
476
DN987378
Issue: 30-0
General Error Messages of System
12442
Error messages
DISCREPANCY BETWEEN SOURCE AND
DESTINATION FILE
The loading records failed, because the record size given
in the source file and the destination file are different.
12443
ILLEGAL VIRTUAL LOADING ADDRESS
The virtual loading address used is illegal: the physical
address of the source computer must be used.
12444
ADMINISTRATIVE STATE OF RELATED BCF IS
INCORRECT
Related BCF is in incorrect administrative state for
requested operation.
12445
PUP CONGESTION DETECTED
PMR User Part Prerouting function has detected
congestion. (Used in NTN/DXT)
12446
PUP PREROUT NOT OK
PMR User Part prerouting function has not found available
route to destination exchange. (Used in NTN/DXT)
12447
VIRTUAL FILE LOADING IN PROGRESS
The virtual loading of groups or files is still in progress.
12448
UNIT OPERATES AS FILE LOADING SOURCE
The unit works as the loading source for the files, and thus
the unit cannot be restarted or its state cannot be
successfully changed.
12449
UNIT OPERATES AS DATABASE LOADING SOURCE
The unit works as the loading source for the databases,
and thus the unit cannot be restarted or its state cannot be
changed.
12450
STATE CHANGE NOT POSSIBLE DURING RESTART
The state of the unit cannot be changed during restart of
the unit.
12451
FLASH OPERATION GOING ON
Unfinished flash memory operation going on.
12452
WINDOWED FILE ACCESS SERVICE ALREADY EXISTS
The windowed file access service already exists in the
system. This error situation occurs when the call for the
program wfa_init_r() in the WFALIB library is repeated
within the same process.
Issue: 30-0
DN987378
477
Error messages
General Error Messages of System
12453
PCM-TSL ALREADY RESERVED
The given PCM-TSL is already reserved.
12454
CCBS SUBSCRIBER ALREADY EXISTS
A CCBS subscriber already exists in this exchange.
12455
PRIVATE NETWORK PARALLEL NUMBER
Parallel number of a private network.
12456
MIB DATABASE IS FULL
The Management Information Base (MIB) is full and
therefore no new object instances can be created.
12457
NAME ALREADY EXISTS
This is general error code which indicates that defined
name already exists in analysis.
12458
NON-EXISTENT FTAM FILE
FTAM file does not exist. This error is selection-related
diagnostics notice, defined in ISO 8571-3.
12459
NO ET FOR PCM
There is no ET for the given PCM circuit.
12460
END OF MML SESSION
With this status MMIMAN tells SEESAM that MML-session
is ended. SEESAM tells with this status to MMIMAN that
whole dialogue is over.
12461
DESTINATION SELECTION REQUEST
With this status MMIMAN requests destination selection
service from SEESAM.
12462
DISK UNIT HAS INCORRECT WORKING STATE WHEN
INSTALLING OR REMOVING CHANGE DELIVERY
The main working state of the disk unit must be WO when
you are installing or removing a Change Delivery.
Alternatively you can also use state SE-NH, in which case
the unit data is ignored.
12463
DISK UNIT DOES NOT EXIST IN THIS NETWORK
ELEMENT
The disk unit given in the CFLIST file does not exist in this
network element.
12464
478
TIMEOUT OCCURRED DURING PREROUTING
DN987378
Issue: 30-0
General Error Messages of System
Error messages
PMR User Part library returns this error code if it does not
get response to prerouting message within time limit.
12465
DIRECTORY TABLE IS CORRUPTED
The directory table used by the service provider of the
windowed file access has corrupted. More than one
directory table records have been marked as invalid.
Recovery procedure cannot be executed and the contents
of the file for the windowed file access service are
damaged.
12466
PARALLEL NUMBER OF PRIVATE NETWORK
PARALLEL NUMBER
Parallel number to parallel number of private network.
12467
RSU SUBSCRIBER PRIVATE NETWORK PARALLEL
NUMBER
Parallel number to RSU subscriber of private network.
12468
PARALLEL NUMBER OF RSU PRIVATE NETWORK
PARALLEL NUMBER
Parallel number to private network parallel number of RSU
subscriber.
12469
ANNOUNCEMENT NUMBER HAS BEEN DEFINED FOR
SUBSCRIBER
The subscriber number is in the NUMBER CHANGED
state and the announcement number has been defined.
12470
NO CALL FORWARDING EXCEPTION
The subscriber has no call forwarding facility.
12471
ANALYSIS FOR CENTREX ADDITIONAL OUT-LINE
NUMBER WAS NOT FOUND
Centrex additional out-line number was not found in
Centrex additional out-line number analysis.
12472
AD&C SUBSCRIBER ALREADY EXISTS
AD&C subscriber already exists in this exchange.
12473
RCSC SUBSCRIBER ALREADY EXISTS
Reminder Call with Charging subscriber already exists in
this exchange.
12474
RCSN SUBSCRIBER ALREADY EXISTS
Reminder Call without Charging subscriber already exists
in this exchange.
Issue: 30-0
DN987378
479
Error messages
General Error Messages of System
12475
ERROR IN DATA LENGTH
Data length does not match with the one given in the load
module.
12476
BAD CONNECTION TYPE
Connection type of Transport Pipe Provider is bad.
12477
BAD CONNECTION END POINT
Connection End Point which is sent by Transport Pipe
User is bad.
12478
OPERATION IS NOT AVAILABLE
Transport Pipe Provider has a state where execution of
this operation is not possible.
12479
COTS DOES NOT RESPOND
Timer which supervises COTS (Connection Oriented
Transport Service ) interface has expired.
12480
TRANSPORT PIPE USER DOES NOT RESPOND
Timer which supervises Transport Pipe User has expired.
12482
COTS HAS CANCELLED THE REGISTRATION
Connection Oriented Transport Service has cancelled
registration.
12483
TRANSPORT PIPE USER HAS CANCELLED THE
REGISTRATION
Transport Pipe User has cancelled registration.
12484
TRANSPORT PIPE PROVIDER HAS CANCELLED
REGISTRATION
Transport Pipe Provider has cancelled registration.
12485
INITIALIZATION OF THE INTERNAL CONNECTION
MATRIX IN MFST-S PLUG-IN UNIT FAILED
A defect in internal connection matrix operation has
occured at the initialization phase of the MFST-S plug-in
unit.
12486
MAXIMUM NUMBER OF INSTANCES EXISTS ALREADY
Operator tries to create new object instance of managed
object class via Q3 interface. Creation fails because there
exists already maximum number of object instances in
network element.
480
DN987378
Issue: 30-0
General Error Messages of System
12487
Error messages
INSTANCE IS NOT DELETED BECAUSE LOG IS NOT
EMPTY
Operator tries to delete managed object instance via Q3
interface. Instance cannot be deleted, because log of
instance is not empty.
12488
CIC NOT FOUND
The circuit identification code was not found in the
CPCMSP file.
12489
UNABLE TO HANDLE EXISTING (OLD) MAFILE WHEN
HANDLING CHANGE DELIVERY
The handling of the MAFILE file existing in the old package
has failed while trying to install or remove the change
delivery.
12490
UNABLE TO HANDLE NEW MAFILE IN CHANGE
DELIVERY
There is something wrong in the new MAFILE file included
in the Change Delivery: the structure may be faulty or the
required load module is missing.
12491
ADMINISTRATIVESTATE AND DESTINATION
ATTRIBUTECANNOT BE SIMULTANEOUSLY IN SET
REQUEST
AdministrativeState attribute and Destination attribute
cannot be in one SET-request at the same time.
12492
SERIAL NUMBER DOES NOT MATCH
The order of arriving messages is incorrect.
12493
CANNOT FIND LOAD MODULE IN CHANGE DELIVERY
OR ITS VERSION DOES NOT MATCH
Installation has been interrupted, because the load module
included in the Change Delivery cannot be found in
MAFILE file or the version data of the Change Delivery
load module and the new MAFILE do not match (in case of
new MAFILE included in Change Delivery). Either MAFILE
file is erroneous or the Change Delivery is erroneously
built.
12494
UNKNOWN MAFILE STRUCTURE FOR CHANGE
DELIVERY INSTALLATION
The SW2ADM Program Block does not recognize the
structure of the MAFILE file.
12495
FIS NUMBER DOES NOT EXIST
First extension number does not exist (private network).
Issue: 30-0
DN987378
481
Error messages
General Error Messages of System
12496
LAS NUMBER DOES NOT EXIST
Last extension number does not exist (private network).
12497
CNS NUMBER DOES NOT EXIST
Call number suffix does not exist (private network).
12498
PNP NUMBER DOES NOT EXIST
Private network parallel number does not exist.
12499
DATABASE DATA DICTIONARY IS UNINITIALIZED
The initialization of data dictionary in the database has not
been run and thus the data dictionary files are empty.
12500
FIRST PARALLEL NUMBER TO PRIVATE NETWORK
First parallel number to the private network.
12501
SECOND PARALLEL NUMBER TO PRIVATE NETWORK
Second parallel number to the private network.
12502
THIRD PARALLEL NUMBER TO PRIVATE NETWORK
Third parallel number to the private network.
12503
FOURTH PARALLEL NUMBER TO PRIVATE NETWORK
Fourth parallel number to the private network.
12504
FIFTH PARALLEL NUMBER TO PRIVATE NETWORK
Fifth parallel number to the private network.
12505
SIXTH PARALLEL NUMBER TO PRIVATE NETWORK
Sixth parallel number to the private network.
12506
SEVENTH PARALLEL NUMBER TO PRIVATE NETWORK
Seventh parallel number to the private network.
12507
EIGHTH PARALLEL NUMBER TO PRIVATE NETWORK
Eighth parallel number to the private network.
12508
NINTH PARALLEL NUMBER TO PRIVATE NETWORK
Ninth parallel number to the private network.
12509
FIRST PARALLEL NUMBER TO RSU PRIVATE
NETWORK
First parallel number to RSU private network subscriber.
482
DN987378
Issue: 30-0
General Error Messages of System
12510
Error messages
SECOND PARALLEL NUMBER TO RSU PRIVATE
NETWORK
Second parallel number to RSU private network
subscriber.
12511
THIRD PARALLEL NUMBER TO RSU PRIVATE
NETWORK
Third parallel number to RSU private network subscriber.
12512
FOURTH PARALLEL NUMBER TO RSU PRIVATE
NETWORK
Fourth parallel number to RSU private network subscriber.
12513
FIFTH PARALLEL NUMBER TO RSU PRIVATE
NETWORK
Fifth parallel number to RSU private network subscriber.
12514
SIXTH PARALLEL NUMBER TO RSU PRIVATE
NETWORK
Sixth parallel number to RSU private network subscriber.
12515
SEVENTH PARALLEL NUMBER TO RSU PRIVATE
NETWORK
Seventh parallel number to RSU private network
subscriber.
12516
EIGHTH PARALLEL NUMBER TO RSU PRIVATE
NETWORK
Eighth parallel number to RSU private network subscriber.
12517
NINTH PARALLEL NUMBER TO RSU PRIVATE
NETWORK
Ninth parallel number to RSU private network subscriber.
12518
PARALLEL NUMBER TO FIRST PARALLEL NUMBER OF
PRIVATE NETWORK
Parallel number to the first parallel number of private
network subscriber.
12519
PARALLEL NUMBER TO SECOND PARALLEL NUMBER
OF PRIVATE NETWORK
Parallel number to the second parallel number of private
network subscriber.
12520
Issue: 30-0
PARALLEL NUMBER TO THIRD PARALLEL NUMBER OF
PRIVATE NETWORK SUBSCRIBER
DN987378
483
Error messages
General Error Messages of System
Parallel number to the third parallel number of private
network subscriber.
12521
PARALLEL NUMBER TO FOURTH PARALLEL NUMBER
OF PRIVATE NETWORK
Parallel number to the fourth parallel number of private
network subscriber.
12522
PARALLEL NUMBER TO FIFTH PARALLEL NUMBER OF
PRIVATE NETWORK
Parallel number to the fifth parallel number of private
network subscriber.
12523
PARALLEL NUMBER TO SIXTH PARALLEL NUMBER OF
PRIVATE NETWORK
Parallel number to the sixth parallel number of private
network subscriber.
12524
PARALLEL NUMBER TO SEVENTH PARALLEL NUMBER
OF PRIVATE NETWORK
Parallel number to the seventh parallel number of private
network subscriber.
12525
PARALLEL NUMBER TO EIGHTH PARALLEL NUMBER
OF PRIVATE NETWORK
Parallel number to the eighth parallel number of private
network subscriber.
12526
PARALLEL NUMBER TO NINTH PARALLEL NUMBER OF
PRIVATE NETWORK
Parallel number to the ninth parallel number of private
network subscriber.
12527
PARALLEL NUMBER TO FIRST PARALLEL NUMBER OF
RSU PRIVATE NETWORK
Parallel number to the first parallel number of RSU private
network subscriber.
12528
PARALLEL NUMBER TO SECOND PARALLEL NUMBER
OF RSU PRIVATE NETWORK
Parallel number to the second parallel number of RSU
private network subscriber.
12529
PARALLEL NUMBER TO THIRD PARALLEL NUMBER OF
RSU PRIVATE NETWORK
Parallel number to the third parallel number of RSU private
network subscriber.
484
DN987378
Issue: 30-0
General Error Messages of System
12530
Error messages
PARALLEL NUMBER TO FOURTH PARALLEL NUMBER
OF RSU PRIVATE NETWORK
Parallel number to the fourth parallel number of RSU
private network subscriber.
12531
PARALLEL NUMBER TO FIFTH PARALLEL NUMBER OF
RSU PRIVATE NETWORK
Parallel number to the fifth parallel number of RSU private
network subscriber.
12532
PARALLEL NUMBER TO SIXTH PARALLEL NUMBER OF
RSU PRIVATE NETWORK
Parallel number to the sixth parallel number of RSU private
network subscriber.
12533
PARALLEL NUMBER TO SEVENTH PARALLEL NUMBER
OF RSU PRIVATE NETWORK
Parallel number to the seventh parallel number of RSU
private network subscriber.
12534
PARALLEL NUMBER TO EIGHTH PARALLEL NUMBER
OF RSU PRIVATE NETWORK
Parallel number to the eighth parallel number of RSU
private network subscriber.
12535
PARALLEL NUMBER TO NINTH PARALLEL NUMBER OF
RSU PRIVATE NETWORK
Parallel number to the ninth parallel number of RSU
private network subscriber.
12536
UNIT IS DUMPING DATABASE
The unit is dumping databases, and thus the unit cannot
be restarted or its state cannot be changed.
12537
UNIT IS COPYING DATABASE
The unit is copying databases, and thus the unit cannot be
restarted or its state cannot be changed.
12538
ISDN ABIS OPTION IS NOT IN USE IN BSC
ISDN Abis feature (which can be used for the Abis
connection between the BTS and BSC) is not supported in
the BSC.
12539
Issue: 30-0
MS SPEED DETECTION OPTION IS NOT IN USE IN
BSC
DN987378
485
Error messages
General Error Messages of System
This feature determines the speed of the MS in GSM/DCS
networks, so that the fast moving mobiles can be directed
to macrocells and the slower mobiles respectively to
microcells.
12540
C/I BASED HANDOVER CANDIDATE EVALUATION
OPTION IS NOT IN USE IN BSC
The crucial principle of the feature is to estimate the level
of the potential co-channel interference on each handover
candidate cell and to use this information in the target cell
evaluation procedure in order to direct MSs to cells which
have the best signal quality.
12541
INCORRECT SUB-TSL PLACE
The value given for the SUB-TSL place is incorrect. In
case of 32 kbit/s LAPD, the place of SUB-TSL is normally
4.
12542
PCM-TSL IS ALREADY IN USE
The given PCM-TSL is already in use.
12543
THERE IS NOT ENOUGH SPACE IN THE PCM CIRCUIT
FOR THE FUNCTIONAL UNIT
The functional unit needs more PCM-TSLs than what is
available in the given PCM circuit.
12544
ALL TIME SLOTS ARE ALREADY RESERVED
All time slots of the given PCM circuit are already
reserved, so it is not possible to add any functional units to
this PCM.
12545
INCORRECT SPEED
The speed given for the D channel is incorrect for this
functional unit.
12546
INCORRECT NUMBER OF MONITORING LINES
The functional unit TDSC (actually DWS) can have 2, 10 or
16 monitoring lines.
12547
INCORRECT NUMBER OF FCSD LINES
The functional unit DSCC can offer 2, 4 or 6 FSCD lines.
12548
YOU CANNOT REMOVE TDSC BEFORE THE
SUBSCRIBER NUMBER OF DWS IS REMOVED
The subscriber number of DWS is actually connected to
the functional unit TDSC, thus the subscriber number of
DWS has to be removed before TDSC can be removed.
486
DN987378
Issue: 30-0
General Error Messages of System
12549
Error messages
DELETE SUBSCRIBER NUMBER BEFORE DSCC
An error occurred, because there is a subscriber number
connected to the DSCC. Remove the subscriber number
before you remove the functional unit DSCC.
12550
PREPARATION OF BACKGROUND DATA FAILED
The preparation of background data for background
loading of the radio network plan has failed.
12551
ORDERED STATE CHANGE OF BACKGROUND DATA IS
ILLEGAL
The state change of the background data is illegal.
12552
INTELLIGENT DIRECTED RETRY OPTION IS NOT IN
USE IN BSC
The INTELLIGENT DIRECTED RETRY option is not in use
in the BSC.
12553
MA LIST DOES NOT CONTAIN ENOUGH
FREQUENCIES
The number of frequencies in the attached MA-list must be
at least the number of the hopping TRXs (in cell) and
maio_offset together.
12554
TRUNK RESERVATION OPTION IS NOT IN USE IN BSC
The Trunk Reservation option is not in use in the BSC. The
purpose of Trunk Reservation is to allow the shared use of
the TCH resources of a single BTS by GSM and MCN
users.
12555
MAXIMUM LENGTH OF STRING VARIABLE IS 223
CHARACTERS
The length of the string variable (and string parameter) in
MML macros cannot be more than 223 characters.
12556
SOME PACKAGES ARE NOT APPLICABLE
One or more of the packages proposed in the object
creation are not applicable in this object class.
12557
VARIABLE IS DEFINED EITHER BY LENGTH OR AS
NUMERAL
The variable in the MML macro should be defined either by
indicating the length of the string variable or by typing
NUMERAL, referring to the numeral variable.
12558
Issue: 30-0
RESOURCE SHORTAGE IN WINDOWED FILE ACCESS
DN987378
487
Error messages
General Error Messages of System
There is not enough resources in the windowed file access
server to complete the requested task.
12559
ALARM SYSTEM COULD NOT CHECK IF THE OMC
UPDATE IS ALLOWED
The alarm system could not check if sending the alarm to
the OMC is allowed or not.
12560
BB HOPPING AND SUPER REUSE TRXS NOT
ALLOWED TO EXIST SIMULTANEOUSLY
When feature intelligent underlay-overlay is in use, bb
hopping and super reuse trxs are not allowed to exist
simultaneously.
12561
RF HOPPING CELLS BCCH TRX NOT ALLOWED TO BE
SUPER REUSE TRX
When intelligent underlay-overlay feature is in use, RF
hopping works only if the cell configuration is one regular
BCCH trx and one or more super-reuse-TRXs.
12562
ILLEGAL CELL CONFIGURATION FOR IUO AND RF
HOPPING
When intelligent underlay-overlay feature is in use, RF
hopping works only when the cell configuration is one
regular BCCH trx and one or more super-reuse-TRXs.
12563
MAIO OFFSET TOO HIGH
MAIO offset is bigger than the number of frequencies in the
used MA-list.
12564
THERE IS NO UNLOCKED BCCH TRX UNDER CELL
The cell must have an unlocked transceiver of the
broadcast control channel (BCCH or CPBCH).
12565
RC0PRB HAS NOT ANSWERED TO ISDN CONNECTION
RELEASE MESSAGE
When ISDN connection is trying to disconnect, RC0PRB
has not answered to release message.
12566
PCM BELONGS TO OTHER OBJECT CLASS
This error code is used when the current PCM belongs to
another object class.
12567
ERROR WHILE COMMUNICATING WITH ELGAME
PROGRAM BLOCK
ELGAME program block does not respond to ZSKPRB
program block or the message that is received from
ELGAME contains an error code.
488
DN987378
Issue: 30-0
General Error Messages of System
12568
Error messages
TYPE OF ID IN NEW AND OLD PACKAGE DO NOT
MATCH
The length of the package type in the new package does
not match with that of the old one.
12569
CHANGING OF DP AREA HAS BEEN INTERRUPTED
The reserving or releasing of the decimal position area
was interrupted. Part of the requested change was carried
out. The reason for the interruption and the area for which
the operation was successful is written to the log.
12570
FAMILY TO BE SUPERVISED NOT FOUND
CPUPRO Program Block has received a supervision with a
process family that has not been created for the computer.
12571
FAMILY HAS NO DYNAMIC LDT SLOTS
CPUPRO has received an order for LDT supervision, but
the given process family has no dynamically managed LDT
slots.
12572
HAND GROUP NOT FOUND
CPUPRO has received an order for the supervision of
hands in a hand type but the hand type that is given
cannot be found.
12573
ILLEGAL PARAMETERS IN SUPERVISION ORDER
There are illegal parameter values in the supervision order
received by CPUPRO.
12574
DRAM CONFIGURATION ERROR
A configuration error was detected in the DRAM data of
the CPU plug in unit.
12575
ERROR WHILE COMMUNICATING WITH USAPRO
PROGRAM BLOCK
USAPRO program block does not respond or the message
that is received contains an error code.
12576
ERROR WHILE COMMUNICATING WITH ZSKPRB
PROGRAM BLOCK
ZSKPRB program block does not respond or the message
that is received contains an error code.
12577
ERROR WHILE COMMUNICATING WITH SOWADM
PROGRAM BLOCK
SOWADM program block does not respond or the
message that is received contains an error code.
Issue: 30-0
DN987378
489
Error messages
General Error Messages of System
12578
DEFINED PACKAGE IS NOT DEFAULT PACKAGE
The package defined in the command is not the default
package. This task can only be performed for the default
package.
12579
TEST CANNOT BE EXECUTED FOR E-TRX OR S-TRX
Test cannot be executed for E-TRX or S-TRX.
12580
TEST CANNOT BE EXECUTED FOR DE34/DF34 BTS IF
BASEBAND FREQUENCY HOPPING IS USED
Test cannot be executed for DE34/DF34 BTS if baseband
frequency hopping is used.
12581
NOT ENOUGH FREE TIME SLOTS
There are too few internal time slots (TSLs) available for a
digital X.25 channel.
12582
ATTACHING MA-LIST TO 2ND GENERATION BTS TYPE
IS NOT ALLOWED
Nokia 2nd generation BTS does not support rf-hopping in
which MA-lists are needed, so attaching of MA-list to the
Nokia 2nd generation BTS is not allowed.
12583
RF-HOPPING IS NOT ALLOWED TO 2ND GENERATION
BTS TYPE
Nokia 2nd generation BTS site does not support rfhopping.
12584
TEST CANNOT BE EXECUTED FOR BCCH CHANNEL
Test cannot be executed for BCCH channel.
12585
RC0PRB HAS NOT ANSWERED TO ISDN CONNECTION
OPENING MESSAGE
When ISDN connection is trying to connect, RC0PRB does
not answer to opening message.
12587
RELEASE OF ISDN CONNECTION FAILED
Releasing of ISDN connection failed.
12588
TRX ISDN NUMBER NOT DEFINED
User has not defined the ISDN number for TRX and that
the ISDN connection is tried to be opened.
12589
BSC ISDN NUMBER NOT DEFINED
User has not defined the ISDN number for BSC and some
ISDN connection is trying to be opened.
490
DN987378
Issue: 30-0
General Error Messages of System
12590
Error messages
D-CHANNEL NOT BLOCKED
The D-channel is not blocked.
12591
THE READING OF NTN DATABASE FAILED
The reading of NTN database failed.
12592
UDATING OF NTN DATABASE FAILED
The data has not been updated in the NTN-database
because of an updating error. In case of DST command,
the addition of D-channel is cancelled.
12593
THE FIRST PCM CIRCUIT IS ALREADY RESERVED
The PCM-circuit given as the first one has already been
reserved for another purpose.
12594
THE SECOND PCM CIRCUIT IS ALREADY RESERVED
The PCM-circuit given as the second one is already
reserved for another purpose.
12595
BOTH PCM-CIRCUITS ALREADY RESERVED
Both of the given PCM-circuits are already reserved for
other purposes.
12596
MA LIST NOT ATTACHED TO UNLOCKED RF-HOPPING
BTS
MA-list is needed in rf-hopping, so MA-list must be
attached to every unlocked rf-hopping BTS.
12597
LOCATION AREA NAME OR CODE ALREADY EXISTS
Location area name or code already exists in radio
network files.
12598
LOCATION AREA DOES NOT EXIST
The location area cannot be found from the radio network
files.
12599
LOCATION AREA CONTAINS SUBSCRIBERS
Subscribers are defined to the location area.
12600
MISMATCH IN PCM TYPE
The bit rate level (full rate, half rate or dual rate) that is
given for the circuit to be added to the circuit group differs
from the bit rate level of the first PCM circuit in the circuit
group. The bit rate levels of the PCM circuits in the same
circuit group must be equal.
Issue: 30-0
DN987378
491
Error messages
General Error Messages of System
12601
TEST CANNOT BE EXECUTED IF RX RTSL IS BCCHCHANNEL
The test cannot be executed if RX RTSL is BCCH-channel.
12602
DATA HAS BEEN CHANGED
The data being handled has been changed during the
execution of MML command.
12603
TOO MANY BTS O&M LINKS DEFINED
The O&M links have been defined more than one to the
site of the D-type
12604
TRX AND O&M LINKS OVERLAPPED ON THE ISDN
LINK
TRX and O&M links have been defined as overlapped on
the ISDN link.
12605
THE PLACE OF ISDN O&M LINK IS NOT DEFINED
The place of the ISDN O&M link has not been defined
though DCH-channel has been created to ISDN TRX.
12606
THE SIZE OF THE ISDN TRX OR O&M LINK IS BIGGER
THAN FREE SPACE
The size of the ISDN TRX or O&M link is bigger than free
space.
12607
ALL CPUS MUST BE CP4HX IF MORE THAN 16 TRXS
IN BCSU
All CPUs must be in CP4HX-type if there are more than 16
TRXs in BCSU.
12609
TOO FEW MEMORY IN CPU WHEN MORE THAN 16
TRXS IN ONE BCSU
Too few memory in CPU when there are more than 16
TRXs in one BCSU.
12610
GSWB MUST BE INSTALLED WHEN MORE THAN 16
TRXS IN BCSU
GSWB must be installed when there are more than 16
TRXs in one BCSU.
12611
TOO FEW AS7-U CARDS WHEN THERE ARE MORE
THAN 16 TRXS IN BCSU
Three AS7-U cards in all BCSUs when there are more
than 16 TRXs in one BCSU.
492
DN987378
Issue: 30-0
General Error Messages of System
12612
Error messages
TOO FEW BCSUS IN WO-EX STATE WHEN THERE ARE
MORE THAN 16 TRXS IN BCSU
Eight BCSUs in WO-EX state when there are more than 16
TRXs in one BCSU.
12613
TOO MANY TCHS IN ONE SIGNALLING UNIT
Maximum number of traffic channels exceeded in one
signalling unit.
12614
HOST CREATION FAILED
The creation of the TCP/IP remote host failed.
12615
HOST NAME IS ALREADY IN USE
The name of the remote host is already in use.
12616
IP ADDRESS ALREADY IN USE
This IP address is already in use.
12617
HOST DOES NOT EXIST
The given remote host does not exist.
12618
SERVICE CREATION FAILED
The creation of the TCP/IP service failed.
12619
SERVICE NAME ALREADY IN USE
The name given for the TCP/IP service already exists.
12620
SERVICE DOES NOT EXIST
This TCP/IP service does not exist.
12621
PORT IS IN USE
The given port number is already used for another local
TCP/IP service.
12622
SERVICE IS NOT BLOCKED
The administrative state of the TCP/IP service is not
blocked.
12623
IP ADDRESS DOES NOT EXIST
The given IP address does not exist.
12624
PORT DOES NOT EXIST
The given port does not exist.
12625
Issue: 30-0
NETWORK INTERFACE CREATION FAILED
DN987378
493
Error messages
General Error Messages of System
Creation of the TCP/IP network interface failed.
12626
NETWORK INTERFACE ALREADY EXISTS
In this computer unit, there already exists a network
interface with the given network interface type (if the type
is Message bus) or with the same network interface type
and plug-in unit index (if the type is Ethernet).
12627
NETWORK INTERFACE DOES NOT EXIST
The given TCP/IP network interface does not exist.
12628
NETWORK INTERFACE IS NOT BLOCKED
The administrative state of the TCP/IP network interface is
not blocked.
12629
ROUTE ALREADY EXISTS
The TCP/IP route already exists.
12630
ROUTE CREATION FAILED
The creation of the TCP/IP route failed.
12631
NEXT HOP COMPUTER DOES NOT EXIST
The next hop computer does not exist.
12632
NEXT HOP CANNOT BE THE SAME COMPUTER
The same computer cannot be used as the next hop
computer of the TCP/IP route.
12633
ROUTE DOES NOT EXIST
The given TCP/IP route does not exist.
12634
ROUTE IS NOT BLOCKED
The administrative state of the TCP/IP route is not blocked.
12635
TCP/IP PARAMETERS ALREADY EXIST
The TCP/IP parameters already exist.
12636
TCP/IP PARAMETERS DO NOT EXIST
The TCP/IP parameters do not exist.
12637
SW PACKAGE REJECTED BY RUNNING SW IN BCF
Unsupported increase of SW package release version.
12638
494
CONFLICT BETWEEN TRANSMISSION TYPE OF TRX
AND NUMBER OF D-CHANNEL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Type of D-channel does not correspond to transmission
type of TRX. An ISDN TRX must have an ISDN link and a
normal TRX must have a fixed link.
12639
TRX OR O&M LINK CANNOT BE IN CLS00 OR CLS01
TRX or O&M link cannot be in CLS00 or CLS01 Dchannel.
12640
SUBSCRIBER ALREADY SEMIPERMANENT
The operator tried to create a semipermanent circuit for the
subscriber, but the subscriber already has one in the
database.
12641
NO SUCH SEMIPERMANENT SUBSCRIBER
The operator tried to delete a semipermanent circuit from
the subscriber, but the subscriber does not have a
semipermanent circuit in the database.
12642
BCF SW PACKAGE VERSION AND HW DATABASE
INCOMPATIBLE
The active SW package in BCF does not support this HW
database. Check the need of possible ASCII file in BCF
and in HW database.
12643
HW DATABASES OF THE SAME TYPE BUT DIFFERENT
LEVEL
The type of the HW databases is the same (DE21/DF12)
but the level is different. Check the use of ASCII file in HW
databases.
12644
HW DATABASE ATTACHED BUT COMPATIBILITY NOT
CHECKED
The HW database was attached but the checking of SW
package version was failed. Make sure that there is an
active SW package attachment to the BCF in case
(ZEWO:bcf_id). The activation of this HW database may
not succeed.
12645
D-CHANNEL STATE MODIFICATION HAS FAILED
Abis D-channel state change modification request sent by
the network management system has failed for some
reason. PXADMI process has returned an error code to the
Q3-agent (to the lapdLink-OCH).
12646
DELETION OF D-CHANNEL IS NOT ALLOWED
Deletion of Abis D-channel is not allowed because it is still
used by some BCF or TRX instance.
Issue: 30-0
DN987378
495
Error messages
General Error Messages of System
12647
HARDWARE OF THE BSC IS NOT ADEQUATE FOR THE
OPERATION
The hardware of the BSC is not adequate for the operation
in question. The adequacy of the hardware is checked
when the network management system is creating more
than 256 Abis D-channels (so-called Large CapacityBSC).
12648
GIVEN RELATED LAPDLINK INSTANCE DOES NOT
EXISTS IN BSC
In create request related Abis-lapdLink (D-channel)
instance given by the network management system has
not been created in the BSC.
12649
TDSC HAS NO SUBSCRIBER NUMBER
The functional unit TDSC has no subscriber number.
12650
INVALID OBJECT INSTANCE PARAMETER IN CMIS
PRIMITIVE
The object instance parameter given for the CMIS primitive
is not semantically correct.
12651
CMIS PRIMITIVE CONTAINED SEMANTICALLY
INCORRECT ACTION INFORMATION
CMIS primitive contained semantically incorrect action
information.
12652
PASSIVE WARMING
Wupman is going to use passive warming to warm up the
group in question. (Not really an error situation, just a
different type of warming is needed)
12653
HOT SPOT OPTION IS NOT IN USE IN BSC
This error code informs the operator that this feature is not
available.
12654
THE GIVEN FREQUENCY IS NOT ALLOWED
The given frequency is not allowed.
12655
SWITCHOVER ACTIVE
Switchover is active.
12656
THE DEVICE (OTHER THAN STM OR FUC) DOES NOT
ANSWER OR RBER2 IS MEANINGLESS
The device (other than STM or FUC) does not answer or
RBER2 is meaningless.
496
DN987378
Issue: 30-0
General Error Messages of System
12657
Error messages
FUC DOES NOT ANSWER OR SENDS A NACK.
ALTERNATIVELY TIMESLOT IS NOT ALLOWED
FUC does not answer in specified time or at all, or it sends
a NACK. Alternatively, timeslot is not allowed.
12658
THE DEVICE (OTHER THAN STM OR FUC) SENDS A
NACK
The device (other than STM or FUC) sends a nack.
12659
THE TIMER OF THE TEST (IN BTS) HAS EXPIRED
The timer of the test (in BTS) has expired.
12660
ADMINISTRATIVE OPERATION IN PROGRESS
Another program block prevents the mml command from
proceeding. Try again in a few seconds.
12661
LIU DOES NOT EXIST
The access could not be created because you have given
one or more of the following parameters incorrectly: FU
type, FU index, LIU type and LIU index. Check the correct
LIU parameters and give the command again.
12662
ACCESS INDEX RESERVED
The given access index is already used for another
access. Check the existing access IDs (command LAI) and
give the command again with a free ID, or leave this
parameter out and let the system automatically choose the
first free ID.
12663
ACCESS NAME RESERVED
The given access name is already used for another
access. Check the existing access names (with command
LAI) and give the command again, using a free access
name.
12667
ACCESS DATA INCONSISTENT
The command could not be executed. The system was not
able to restore the data into original form, thus the data is
now inconsistent. Try to delete the access and then give
the command again. If this does not help, you can reboot
the SVMANA Program Block and then give the command
again.
12668
ACCESS DOES NOT EXIST
The access that was identified either with the access ID or
the access name, was not found. Check the correct
identifier (command LAI) and give the command again.
Issue: 30-0
DN987378
497
Error messages
General Error Messages of System
12669
COMMAND NOT EXECUTED
The command was not executed. The system, however,
restored the data into original form, as it was before the
command was given. Give the command again.
12670
ACCESS NOT IN LOCKED STATE
The administrative state of the access must be locked to
execute this command. Change the state into locked
(command LAG) and give the command again.
12672
ACCESS PROFILE DATA INCONSISTENT
The command was not executed. The system was not able
to restore the data into original form, thus some
discrepancy now occurs in the data. Try to delete the
access profile (command LAE) and give the command
again. If this does not help, you can reboot the SVMANA
Program Block and give the command again.
12674
ENHANCEDFULLRATE OPTION NOT IN USE
The enhanced full rate option is not in use.
12675
INTERNAL ERROR IN PROGRAM BLOCK CPUPRO
The desired service cannot be provided due to an internal
error in CPUPRO program block.
12676
WORKSTATION USER AUTHORIZATION FAILED
Session manager has detected that the given workstation
password was wrong or the username was unknown.
(Used in NTN/DXT)
12677
DATA MANAGER DID NOT RESPOND IN TIME
User of a data manager (DMASYB) service detected that
data manager did not respond in time. (Used in NTN/DXT)
12678
INDEX ALREADY EXISTS
The given index is already assigned to an existing object.
12679
SIGNALLING POINT CODE ALREADY RESERVED
The given signalling point code is used by an existing
route.
12680
SIGNALLING NETWORK DOES NOT EXIST
The given signaling network does not exist in this
exchange.
12681
498
SIGNALLING POINT CODE DOES NOT EXIST
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The given signaling point code does not exist for this
signaling network.
12682
DATABASE UPDATE FAILED
The command failed. The database is in old, consistent
state.
12683
CREATE FAILED AND RELEASE OF SPC FAILED
An entry to the database is failed and the reserved SPC
could not be released. It cannot be re-used or deleted by
standard operations.
12684
ROUTE DATA FULL
The maximum number of routes have already been
created.
12685
ROUTE ADMINISTRATIVE STATE INCORRECT
Deleting an unlocked route has been attempted.
12686
ROUTE NOT EMPTY
Deleting a route containing VPC Endpoint Groups has
been attempted.
12687
ROUTE RESERVATION STATE INCORRECT
The route is reserved and cannot be deleted.
12688
RELEASE OF SPC FAILED
The route has been deleted but the release of the SPC
failed. It cannot be reused or deleted by standard
operations.
12689
ROUTE NAME DOES NOT EXIST
The route identified by the given route name was not
found.
12690
EMPTY ROUTE NOT UNLOCKED
It is not allowed to unlock a route that does not contain any
VPCE Groups.
12691
LINE IS ALREADY IN USE
Access could not be created because the line of LIU is
already being used by another access. Change LIU
information so that the line is free, and give the command
again.
12692
Issue: 30-0
ALARM UPLOAD IS BUSY
DN987378
499
Error messages
General Error Messages of System
Alarm upload is currently going on, and another
simultaneous alarm upload request is not allowed.
12693
LAPD EVENT LOGS ARE NOT ACTIVE
LAPD event logs are not active.
12694
PID OF SERVER IS OF WRONG TYPE
If it is a general service, the PID of the server has to be an
FAR PID.
12695
EVENT LOG STREAM NUMBER IS INVALID
The given event log stream number is invalid: it is bigger
than the maximum stream number in the ELSPAR or
ESTADT File or it is bigger than the maximum number of
event log streams in the unit.
12696
EVENT LOG STREAM ALREADY EXISTS
The given event log stream already exists, i.e. the event
log stream number is already in use.
12697
B-CHANNELS ARE STILL IN USE
B-channels are still in use. The B-channels must be
removed before the D-channel can be deleted.
12698
GROUP NAME DOES NOT EXIST
The group identified by the given group name was not
found.
12699
VPCE DOES NOT EXIST
The VPCE identified by the given VPCI was not found.
12700
GROUP IDENTIFIER OUT OF RANGE
Identifier of VPCE-group is not correct.
12701
VPCE GROUP NOT EMPTY
Deleting a VPCE group which contains VPC Endpoints has
been attempted.
12702
VPCE GROUP ADMINISTRATIVE STATE INCORRECT
Deleting an unlocked VPCE group has been attempted or
deleting of the last VPCE was attempted while group was
not locked.
12703
VPCES ADMINISTRATIVE STATE INCORRECT
Deleting an unlocked VPCE has been attempted.
12704
500
NO SPACE FOR UNIT TYPE IN REMOTE STATION
DN987378
Issue: 30-0
General Error Messages of System
Error messages
No more unit types can be saved in the given remote
station.
12705
NO SPACE FOR UNIT INDEX IN REMOTE STATION
No more unit indexes can be saved in the given remote
station.
12706
UPLOAD TYPE IS NOT SUPPORTED
The type of the upload request is not one of the constants
given in the definition of upload_type_t data or the type is
not supported by the current software.
12707
COPY TASK IS ABORTED BY REQUEST
Active copy task is terminated by request.
12708
COPY TASK ERROR LIMIT EXCEEDED
The error limit for the copy task has been exceeded.
12709
TOTAL FILE COPY TIME EXCEEDED
The time limit for copying mass memory files has been
exceeded.
12710
SINGLE FILE COPY TIME LIMIT EXCEEDED
The copy time for single mass memory file has been
exceeded.
12711
UNKNOWN ID FOR COPY TASK
The identification given for the copy task in the mass
memory cannot be used.
12712
ERROR WHILE DELETING USER SPECIFIC VALUES
The network element access control manager could not
delete user-specific values. Use commands in IUcommand group to delete values or to get more
information.
12714
BB HOPPING AND E-TRX OR S-TRX CANNOT BE USED
SIMULTANEOUSLY IN A BTS
BB hopping and E-TRX or S-TRX cannot be used
simultaneously in a BTS.
12715
BB HOPPING AND SUPER REUSE AND REGULAR
TRXS NOT ALLOWED TO EXIST SIMULTANEOUSLY
If cell is BB (base band) hopping, it can contain only
regular or super reuse TRXs.
Issue: 30-0
DN987378
501
Error messages
General Error Messages of System
12716
E-TRX AND S-TRX ARFCN IS NOT ALLOWED TO BE IN
THE MA LIST OF BTS
E-TRX and S-TRX ARFCN is not allowed to be in the MA
list of BTS.
12717
BUFFER NOT DETACHED
There is an attachment to the buffer.
12718
FAILURE IN BUFFER RELEASE
The buffer could not be released.
12719
FTAM MODIFY EXECUTED PARTLY CORRECTLY
This error code may appear when the FTAM modify has
been executed and the filename has had wildcard(s). The
error code indicates that at least one modify operation has
been successful and at least one modify operation has
been unsuccessful.
12720
FTAM FILENAME MODIFY NOT ALLOWED WHEN
USING WILDCARDS
Ftam filename modify is not allowed when using wildcards.
Rename the files individually without wildcards.
12721
NO ESTADT FILE ON THE DISK
When creating a new event log stream, it is possible to use
the old estadt file. However, if the ESTADT file does not
exist on the disk, the creation of the new event log stream
does not succeed.
12722
REFERENCE LOCATION AREA DOES NOT EXIST
The reference location area cannot be found from the radio
network files.
12723
LOCATION AREA CONTAINS BASE TRANSCEIVER
STATIONS
Base Transceiver Stations are defined to the location area.
12724
LOCATION AREA CONTAINS BASE TRANSCEIVER
STATIONS AND SUBSCRIBERS
Base Transceiver Stations and subscribers are defined to
the location area.
12725
TCP/IP PARAMETER CREATION FAILED
The creation of TCP/IP parameters failed.
12726
502
THERE IS NO UNLOCKED E-RACH E-TRX UNDER AN
EXTENDED AREA
DN987378
Issue: 30-0
General Error Messages of System
Error messages
There is no unlocked E-RACH E-TRX under an extended
area.
12727
NO E-RACH E-TRX UNDER EXTENDED AREA
There is no E-RACH E-TRX under extended area.
12728
COMMUNICATION ERROR BETWEEN YESMAN AND
TZIPPI PROGRAM BLOCK
TZIPPI Program Block does not answer to the request
initiated by YESMAN Program Block.
12729
SEMAPHORE TIME SUPERVISION EXPIRED
Time supervision on semaphore has expired.
12730
DATABASE BACK-UP COPYING NOT IN PROGRESS
Database has received a back-up copying termination
request, but there is no back-up copying of database in
progress.
12731
UPDATE OF ACCESS DATA FAILED
Updating of access data in the database failed.
12732
ACCESS COULD NOT BE FOUND IN DATABASE
The given access could not be found in the database.
12733
ACCESS ID ALREADY EXISTS IN DATABASE
An attempt was made to create a new access by using an
ID which already exists in the database.
12734
ACCESS NAME ALREADY IN USE
An access with the given name already exists in the
database.
12735
ACCESS PROFILE ID ALREADY EXISTS IN DATABASE
The given access profile ID already exists in the database.
12736
ACCESS PROFILE ALREADY EXISTS
A profile for the access already exists in the database.
12737
ACCESS PROFILE UPDATE IN DATABASE FAILED
Updating of access profile in the database failed.
12738
ACCESS PROFILE DOES NOT EXIST IN DATABASE
The specified access profile does not exist in the
database.
Issue: 30-0
DN987378
503
Error messages
General Error Messages of System
12739
CONNECTION FOR LINK TERMINATION POINT DOES
NOT EXIST
There is no connection for the given link termination point
in the database.
12740
HARDWARE FOR ATM INTERFACE ALREADY IN USE
Attempt was made to attach a hardware that is already in
used for another ATM interface.
12741
MODIFYING UNMODIFIABLE ACCESS DATA
An attempt was made to modify such access data fields
that are not modifiable.
12742
MULTIPOINT BRIDGE MISSING IN DATABASE
For some reason the multipoint bridge object for point-tomultipoint connection in database is missing.
12743
TC ADAPTOR MISSING IN THE DATABASE
The TC adaptor object for access is missing in the
database.
12744
UPDATING TC ADAPTOR TO DATABASE FAILED
The update of the TC adaptor to database failed.
12745
CANNOT MODIFY TPS OF A CONNECTION VIA LEAF
TP
The termination points of a connection cannot be modified
via leaf point of a point-to-multipoint connection.
12746
TARGET DOES NOT EXIST
The target does not exist in the database.
12747
COULD NOT CHANGE DATA ON VC CONNECTION
TERMINATION POINT
An attempt was made to delete a Virtual Channel link
termination point that has connections, or to make a
connection to a termination point whose other connections
do not allow the type of connection requested.
12748
VCI ALREADY IN USE
The given Virtual Channel Identifier is already in use.
12749
VCI EXISTS UNDER VPI
An attempt has been made either to delete a Virtual Path
Link Termination Point (VPLT) that has Virtual Channel
Identifiers (VCI) under it, or to create VP connections to a
VPTP that has VCIs under it.
504
DN987378
Issue: 30-0
General Error Messages of System
12750
Error messages
UPDATING VCI TO DATABASE FAILED
Database update of VCI object failed.
12751
VCTP NOT AVAILABLE AS ROOT POINT OF
CONNECTION
Virtual channel link termination point was already either a
point in a point-to-point connection, or a leaf point in a
point-to-multipoint connection, when trying to use it as a
root point in a new point-to-multipoint connection
12752
VP CONNECTION EXISTS
An attempt has been made to delete a virtual path link
termination point with connections, or to make a
connection to a termination point that has already
connections that do not allow the requested type of
connections.
12753
VPI ALREADY EXISTS IN DATABASE
The given VPI is already in use under a specified access.
12754
VPTP EXISTS UNDER ACCESS
An attempt has been made to delete an access which still
has existing vpis.
12755
VPI IS RESERVED
An attempt has been made either to delete or to VPconnect a VPTP with reservation.
12756
VPI UPDATE TO DATABASE FAILED
Updating VPI to database failed.
12757
VPTP NOT AVAILABLE AS ROOT POINT OF
CONNECTION
Virtual path link termination point was already either a point
in a point-to-point connection, or a leaf point in a point-tomultipoint connection, when trying to use it as a root point
in a new point-to-multipoint connection.
12758
WRONG TYPE OF CONNECTION
An attempt has been made to access a point-to-pointconnection with a routine intended for accessing point-tomultipoint-connections, or the other way round.
12759
CHANNEL ALREADY RESERVED FOR ANOTHER
APPLICATION
The channel is already reserved for another application.
Please try again later.
Issue: 30-0
DN987378
505
Error messages
General Error Messages of System
12760
NO SUCH DIRECTORY ON TAPE
The directory cannot be found on tape.
12761
NO SUCH FILE ON TAPE
The file cannot be found on tape.
12762
MMI ACTION PREVENTED DUE THE STATE OF
BACKGROUND DATA
BCFs and BTS unlock and BCFs background parameters
modification is not allowed when BSCs background data
state is activating and under BCF at least one BTSs
background swap flag is to_be_swapped.
12763
DEFINITIONS OR THEIR ORDER DO NOT
CORRESPOND TO DECLARATIONS
The parameters must be defined in the order given in
declaration, and the variables must be defined after the
parameter definitions.
12764
WXSERV WS USERS GOT FROM THE DB WAS MORE
THAN IT CAN HANDLE
WXSERV had over flown when getting the WS users from
the database.
12765
THE GIVEN WXS_TAG IS UNKNOWN
The given wxs_tag is not found from the legal wxs_tags.
12766
THE WS USERS DO NOT FIT TO ONE PACKET (MANY
PACKETS ARE NOT SUPPORTED IN REL 1)
WS users do not fit to one packet (in rel 1 it is supposed
that all the WS users fit to one packet).
12767
DXT COMMERCIAL OPTION LIMIT REACHED
Attempt to add more units of the given type failed due to
the commercial option limit.
12768
CELL ALREADY HAS ADJACENT CELL WITH THE NEW
LAC_CI VALUE
Cell already has such adjacent cell which has the same
LAC and CI value as the new LAC_CI value of the
modified adjacent cell.
12769
INCORRECT NETWORK INTERFACE TYPE
The type of network interface is incorrect.
12770
ILLEGAL COPY FILE LIST
The copy file list is illegal and thus cannot be handled.
506
DN987378
Issue: 30-0
General Error Messages of System
12771
Error messages
IMSI RESERVED
The IMSI number is already being used by another
subscriber.
12772
THE LOCATION DOES NOT EXIST IN THE DATABASE
The location does not exist in the database.
12773
THE CELL DOES NOT EXIST IN THE DATABASE
The cell does not exist in the database.
12774
CARRIER DOES NOT EXIST IN THE DATABASE
The carrier pair does not exist in the database.
12775
FREQUENCY BAND DOES NOT EXIST IN THE
DATABASE
The frequency band does not exist in the database.
12776
DUPLEX SPACING DOES NOT EXIST IN THE
DATABASE
The duplex spacing does not exist in the database.
12777
BASE STATION DOES NOT EXIST IN THE DATABASE
The base station does not exist in the database.
12778
TTRX DOES NOT EXIST IN THE DATABASE
The TTRX does not exist in the database.
12779
TBC DOES NOT EXIST IN THE DATABASE
The TBC does not exist in the database.
12780
FREQUENCY BAND MUST NOT BE DELETED IN THE
DATABASE
The frequency band must not be deleted in the database.
12781
DUPLEX SPACING MUST NOT BE DELETED IN THE
DATABASE
The duplex spacing must not be deleted in the database.
12782
CARRIER PAIR MUST NOT BE DELETED IN THE
DATABASE
The carrier pair must not be deleted in the database.
12783
CELL HAS EXISTED IN THE DATABASE ALREADY
The cell has existed in the database already.
12786
Issue: 30-0
CARRIER PAIR NUMBER IS INVALID
DN987378
507
Error messages
General Error Messages of System
The carrier pair number is invalid. Carrier pair numbers
can be 0, 1, 2, ..., 4095.
12787
RADIO NETWORK CONFIGURATION DATABASE
ERROR
Radio Network Configuration database error. The software
error is: database transaction error or FORM program
error.
12788
THE DELETE TRANSACTION WAS UNSUCCESSFUL
The delete transaction was unsuccessful. The database
object was not deleted from the database.
12789
CHANNEL IS TEMPORARILY RESERVED BY SYSTEM
Statistic collection has reserved the channel temporarily,
please try again later.
12790
COMPUTER UNIT HAS NO TCP/IP SERVICE
A local service cannot be created in a computer unit which
does not have a service program block for TCP/IP data
transfer.
12791
IP ADDRESS IS ILLEGAL
The format of the IP address is incorrect or it is one of the
forbidden addresses.
12792
WAGONS DATABASE IS FULL
There is no room for new data in the database.
12793
NAME SERVER IS NOT READY TO SERVE
The name server is not ready to serve. The computer of
the name server is in the process of boot loading.
12794
USER HAS MORE THAN ONE DIRECTORY NUMBER
Operation (e.g. user deletion) cannot be carried out if the
user has more than one directory number. Remove
excessive numbers and try again.
12795
ACTIVE CALL(S) EXIST
There are active call(s) controlled by the signaling channel
to be removed. If you want to delete the directory number
and remove the signaling channel anyway, use FORCED
parameter.
12796
508
DIRECTORY NUMBER IS USER PRIMARY NUMBER
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Operation (e.g. directory number removing) can be carried
out with user primary number only if it is user last number.
Delete other numbers or change the primary number of the
user.
12797
UPC PARAMETER SETUP FAILED
The setup of UPC parameters for virtual connection failed.
12798
CHANGE OF PVP STATE FAILED
Changing the state of PVP connection failed.
12799
CHANGE OF PVC STATE FAILED
Changing the state of PVC connection failed.
12800
ACCESS STATE CHANGE FAILED
Change of access state failed.
12801
TOO MANY CONNECTIONS PER MESSAGE
The maximum number of connections per message has
been exceeded.
12802
TOO MANY CONNECTIONS FOR ACCESS LINE
The maximum number of connections per access line has
been exceeded.
12803
VIRTUAL CHANNEL TERMINATION POINTS EXISTS
Operation failed because of the VCIs in use under VPI.
12804
VIRTUAL PATH TERMINATION POINTS EXIST
The operation failed because of the VPIs in use under
access.
12805
VIRTUAL PATH TERMINATION POINT RESERVED
Operation failed because the virtual path termination point
was reserved.
12806
NO SUCH TRACING HAS BEEN ACTIVATED
No such tracing has been activated for the subscriber/imei;
the trace origin does not match.
12807
PENDING TRACING HAS ALREADY BEEN SET
Pending tracing has already been set for the
subscriber/imsi.
12808
PENDING TRACING HAS NOT BEEN SET
Pending tracing has not been set for the subscriber/imei.
Issue: 30-0
DN987378
509
Error messages
General Error Messages of System
12809
DB ARRAY IS FULL
DB array is full, no free space for new element.
12810
TLV DATA AREA OVERFLOW
The end of the data area was reached unexpectedly when
encoding or decoding a TLV-coded message. If this
happened during encoding, the data area was already full
when new data was written on it. If it happened during
decoding, the data area was too small for the message
received.
12811
THE STRUCT LEVEL PARAMETER GIVEN TO THE TLVENCODING OPERATOR IS ILLEGAL
The STRUCT level parameter, whose legal values depend
on the current STRUCT level, is illegal. The given
parameter may only be one level higher than the current
STRUCT level. The parameter is used by TLV-encoding
operators.
12812
THE END OF THE CURRENT OPERATION ELEMENT
WAS REACHED WHILE DECODING
This code does not indicate an error. It is used to indicate
to the application decoding the TLV-message that the
current operation element has been fully decoded.
12813
THE END OF MESSAGE WAS REACHED WHILE
DECODING
This code does not indicate an error. It is used to indicate
to the application which is decoding the TLV-message, that
the message is in the end.
12814
INVALID INTERRUPT
Unknown interruption.
12815
THE PARAMETER SHOULD NOT BE MODIFIED
This error code is used to indicate to the service user that
the parameter is critical (warning flag on) and should not
be (was not) changed.
12816
DATA ITEM IS ALREADY HANDLED BY ANOTHER
USER
One sequence of services handles the same subscriber,
ws user, organization block or a net. During the sequence,
the data item is locked and the serving data manager does
not accept service requests outside the sequence
concerning the locked data items. Instead, this error code
is returned in the ack message. If this error code comes,
the service user may wait and try again.
510
DN987378
Issue: 30-0
General Error Messages of System
12817
Error messages
DATA MANAGER IS BUSY AND REFUSES THE
SERVICE REQUEST
This error code is used in data management services to
indicate that a data manager cannot handle the request at
the moment. This error code occurs when there are no free
hands available.
12818
MAX. NUMBER OF ERRORS IN ONE SERVICE
EXCEEDED
This error code indicates that the maximum number of
errors in one service has been exceeded. If this happens
during a transaction, the current procedure is stopped. It is
a matter of hand process if the rest of the list members are
to be handled separately. Index in ec_tag_t indicates the
first list member that has not been handled.
12819
SOMETHING WRONG WITH THE DATA
This error code is used by the data managers to tell the
service user that the data in the service request was
erroneous.
12820
ILLEGAL INPUT DATA
This error code is used, when input data has illegal input
values, i.e values NOT mentioned in possible values - list
of corresponding datatype. This error code is used in
dma_ack_s messages in field tag_list.data(*).error. The
general error code in result - field is usually set to
dm_error_in_data_ec.
12821
ORGANIZATION BLOCK IS NOT A ROOT
ORGANIZATION BLOCK
This error code is used by the data management services
to indicate that the requested organization block is not a
root organization block. Parameters and districts can be
defined for root organization blocks (read organizations)
only.
12822
DATABASE OBJECT HAS RELATIONS TO GROUP
OBJECT(S)
This error code is used by the data management services
to indicate that the requested object (organization
block/district) in the database has relations to group
object(s).
12823
ORGANIZATION BLOCK OBJECT HAS SUBLEVEL
BLOCK OBJECT(S)
This error code is used by the data management services
to indicate that the requested object (organization block) in
the database has sublevel block object(s)
Issue: 30-0
DN987378
511
Error messages
General Error Messages of System
12824
DATABASE OBJECT HAS RELATIONS TO SUBSCRIBER
OBJECT(S)
This error code is used by the data management services
to indicate that the requested object (organization block) in
the database has relations to subscriber object(s).
12825
REQUESTED OBJECT DOES NOT EXIST IN THE
DATABASE
This error code is used by the data managers to indicate to
the service user, that the requested object can not be
found from the database.
12826
THERE IS NO PARENT ORGANIZATION BLOCK IN THE
DATABASE FOR THE ORGANIZATION BLOCK
This error code is used by the data management services
to indicate that the creation of an organization block, that
does not have a parent block, was attempted.
12827
OPERATION WAS PARTLY SUCCESSFUL
This error code is used by data management services to
indicate that the operation was partly successful. This is
used e.g. in list updating services as the general status
when some of the list items were successful and some
were not. In these services, there is also a more specific
error code for each unsuccessful list item returned.
12828
THERE IS NO PARAMETER WITH THE GIVEN ID IN THE
DATABASE
This error code is used by the data management services
to indicate that the requested parameter(s) does not exist
in the database.
12829
INTERNAL COMMUNICATION ERROR BETWEEN
PROGRAM BLOCKS HAS OCCURED
The error code is given by the data managers to indicate
that the dma_header structure in a service request is
somehow faulty.
12830
PARAMETER VALUE IS NOT VALID
This error code is used by the parameter read transactions
(get_system_parameter_do, get_exchange_parameter_do
and get_organization_parameter_do) to indicate to the
calling application, that the wanted parameter value is not
valid (i.e. the parameter is turned into an "Off/Infinite"
state).
12831
512
SESSION MANAGER IS UNABLE TO PROCESS THE
REQUEST
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Session manager (SXMPRB in NTN/DXT) cannot do the
requested operation. The reason is internal malfunction or
overload of SXMPRB.
12832
PAGING NOT UPDATED
The paging data of the WLL terminal have not been
updated.
12833
ILLEGAL TYPE OF DB OBJECT
This error code is used when, for example, the given SSI is
an ID of something else than the requested object type.
12834
OBJECT ALREADY EXISTS IN THE DB
This error code is used by the data management services
to indicate that the requested object is already in the
database.
12835
THE DATABASE OBJECT HAS RELATIONS TO OTHER
OBJECTS.
This error code is used by the data management services
to indicate that the requested object in the database has
relations to other objects.
12836
THE CREATION OF A NEW OBJECT TO THE
DATABASE FAILED FOR SOME REASON
This error code is used by the data management services
to indicate that the creation of a new object would have
been possible, but the creation failed because of the
database.
12837
UNSUCCESSFUL DELETION OPERATION IN DB
This error code is given when, for example, the object
requested does not exist in the db.
12838
OBJECT TABLE FULL
Error code for indicating that the number of maximum
parallel db operation has exceeded.
12839
RELATION DOES NOT EXIST IN DB
This error code is used when a non-existent relation is
found, when an existing relation is expected.
12840
IP ADDRESS NETWORK PART IS NOT SUITABLE
The network part of the IP address cannot be similar for
the destination address of the route and for the IP address
of the network interface in the same computer.
Issue: 30-0
DN987378
513
Error messages
General Error Messages of System
12841
INTERPRETING KADATA EXECUTION DEFINITION
FAILS
The execution definition for MML commands in KADATA
Database contains an illegal command or there is an error
in the order of commands, thus the interpretation fails. It is
also possible that the definition describes an erroneous
execution.
12842
THE REQUESTED WS USER IS CURRENTLY LOGGED
The requested WS user is currently logged and the
requested operation cannot be completed.
12843
NO RESPONSE WITHIN THE TIME LIMIT
A data management service could not be completed
because there was no response from a called service
within the time limit.
12844
GENERAL DATA MANAGEMENT FAILURE
A data management service did not succeed.
12845
USER IS LOCKED AND CANNOT BE MODIFIED
The user's data is locked and they cannot be modified (e.g.
someone else is currently modifying the requested user).
12846
UNKNOWN ORGANIZATION BLOCK
The requested organization block does not exist in the
database.
12847
UNKNOWN CELL
The requested cell does not exist in the database.
12848
UNKNOWN LOCATION AREA
The requested location area (LA) does not exist in the
database.
12849
UNKNOWN CALL ID
The requested call ID does not exist in the database.
12850
UNKNOWN GROUP
The requested group does not exist in the database.
12851
CALLBACK REQUEST CREATION FAILED
Callback request creation to the database failed.
12852
514
ERROR IN SYSTEM PARAMETERS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The requested system parameter does not exist in the
database.
12853
ERROR IN ORGANIZATION PARAMETERS
The requested organization parameter does not exist in
the database.
12854
ERROR IN EXCHANGE PARAMETERS
The requested exchange parameter does not exist in the
database.
12855
UNKNOWN CONNECTION GROUP
The requested connection group does not exist in the
database.
12856
UNSUCCESSFUL BUFFER OPERATION
This code is used when buffer allocation or usage has not
been successful.
12857
SUBNET NETWORK INTERFACE IS UNBLOCKED
The modification of the IP address is not possible, because
a network interface in the subnetwork is unblocked. Or
else the modification of the administrative state of the
network interface is not possible, because the IP address
network part of the network interface is different from the
network part of the other IP addresses in the same
subnetwork.
12858
INCORRECT IP ADDRESS NETWORK PART
The network part of the IP address differs from the network
part of other network interfaces in the same subnetwork.
12859
BTS NOT FOUND IN RADIO NETWORK DATABASE
The base station has not been created into the database.
There must be an existing BTS under which a transceiver
or a Frequency Hopping System can be created.
12860
BTS POWER CONTROL PARAMETERS NOT FOUND IN
RADIO NETWORK DATABASE
The power control parameters of the BTS have not been
created into the radio network database.
12861
TERMINATION POINT IS NOT IN LOCKED
ADMINISTRATIVE STATE
The operation requires the termination point to be in locked
administrative state. Lock the termination point and give
the command again.
Issue: 30-0
DN987378
515
Error messages
General Error Messages of System
12862
TERMINATION POINT DATA INCONSISTENT
The operation could not be completed. The system was
unable to restore the data like it was before the operation
and the data is inconsistent. Try to delete the termination
point and give the command again. If this does not help,
you can reboot SVMANA and give the command again.
12863
CONNECTION DATA INCONSISTENT
The operation could not be completed. The system was
unable to restore the data like it did before the operation
and the data is inconsistent. Try to delete the connection
and give the command again. If this does not help, you can
reboot SVMANA and give the command again.
12864
DB ACTION FAILED AND SPC WAS NOT RELEASED
Transaction to create a new route to database failed. The
signaling point code that was reserved before transaction
could not be released. The SPC should be released with
signaling point administrative commands by the operator.
12865
ROUTE DELETED FROM DATABASE SPC NOT
RELEASED
Route deleted successfully from database but signalling
point code could not be released. The signalling point code
should be released using signalling point code
administrative commands by the operator.
12866
THE RESERVATION STATE IS ALREADY RESERVED
The reservation state is already reserved. The state cannot
be changed to the value it already has.
12867
THE RESERVATION STATE IS ALREADY UNRESERVED
The reservation state is already unreserved. The state
cannot be changed to the value it already has.
12868
VPCE CREATION FAILED VPTP NOT RELEASED
The creation of VPC endpoint to the database failed and
the virtual path termination point that was already reserved
could not be released.
12869
VPCI IS NOT FOUND IN NOT ASSIGNING GROUPS
The VPCI specified in the service request is not found
among the VPCIs that the other network element can
assign. The VPCI might be among those VPCIs that this
network element assigns.
12870
516
ERROR IN DATABASE OPERATION
DN987378
Issue: 30-0
General Error Messages of System
Error messages
This error code indicates that a transaction has not been
successful.
12871
USER HAS NO RIGHTS
When the DWS requests an event, the user right is
checked. If the user does not have right, this error code is
returned.
12872
NEXT HOP IS BLOCKED
Route cannot be taken into use, i.e. its administrative state
cannot be changed into unblocked because the next hop
computer is blocked.
12873
THE DATA TAG IN TLV-CODE MESSAGE IS NOT
CORRECT
The data tag in the TLV-coded message is not correct. This
error occurs when, e.g. an event of creating a radio
subscriber is requested, but the fixed data sent to the
event handler is not ru_attributes_c.
12874
THE TARGET IN TLV-CODE MESSAGE IS NOT
CORRECT
This error code is used by the event handler to indicate
that the target element in the tlv-coded message is not
correct.
12875
ERROR OCCURS WHEN DECODING THE TLV-CODE
MESSAGE
This error code is used to indicate an error that occurs
when decoding the TLV-coded message.
12876
THE GIVEN TARGET IS NOT HANDLED BY EVNPRB
The target element sent by the service user is not handled
by the event handler.
12877
THE COMMAND IS NOT KNOWN BY EVENT HANDLER
This error code indicates an error when the event handler
receives an unknown command.
12878
EVNPRB FAILURE
An error occurs in the EVNPRB program block.
12879
COLLECTION FOR THE MEASUREMENT GOING ON
PUMPRB sends this error when the operator tries to
modify measurement but collection for the measurement is
going on.
12880
Issue: 30-0
ILLEGAL TIME QUOTA PARAMETER FOR HAND
DN987378
517
Error messages
General Error Messages of System
The time quota parameter given in hand CREATE
operation was illegal. The value of the parameter must be
between 2 and 0x7FFFFFFF (inclusive).
12881
SPECIFIED HAND GROUP DOES NOT EXIST
The specified hand group does not exist. The hand group
parameter is erroneous, or that specific hand group has
not been initialized yet.
12882
MASTER NOT WARM IN SPARE UNIT
The hand reservation failed because master process has
not been warmed yet. This error can only occur if
OPT_TNSDL_SYNC_C family attribute or a hand group
specific additional option 2 is in use.
12883
NO HAND CREATE SYNC MESSAGE FROM WO UNIT
The master in spare unit did not receive a hand creation
synchronization message from SP unit within the time limit.
12884
DIFFERENT INPUT BEFORE CREATE IN WO AND SP
UNITS
The latest input received before CREATE was not the
same in WO and SP units.
12885
MEMORY ALLOCATION FAILED IN WORKING UNIT
Memory allocation failed in working unit and due to
synchronization, the same error code was propagated to
its spare unit.
12886
DISK FILE UPDATES PREVENTED
Updates of disk-file copies of memory files are prevented.
12889
PXRECE HAS NOT ACKNOWLEDGED UPDATING
REQUEST
Pxrece has not acknowledged the distribution table update
request made by the ABIPRB. The ABIPRB has cancelled
an ongoing switchover.
12890
PXRECE HAS NOT ACKNOWLEDGED UPDATING
REQUEST TO AOMPRB
Pxrece has not acknowledged the updating request of the
distribution table to AOMPRB.
12891
GIVEN VALUE IS ILLEGAL
The given value is illegal or it has caused some value in
the database to become illegal.
12892
518
BTS_STATE_CHANGED MESSAGE NOT RECEIVED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The BSC has not received BTS_STATE_CHANGED
message due to failed TRX configuration. TRX operative
state will be set to BL_SYS.
12893
OBSERVATION ALREADY RUNNING
Observation has already been started and is running.
12894
THERE ARE TOO MANY BCFS IN ONE SIGNALLING
UNIT
In creation of BCF (site type B or D) or in creation of TRX
(site type F) or in O&M-link modification it was noticed that
there will be too many BCFs in one signalling unit.
12895
DUMPING GOING ON
It is not possible to set prevention on disk-file updates of
memory files while dumping is going on. Use DUPHANMML to find out who has set up prevention or to force
prevention off, when possible.
12896
GIVEN USERNAME ALREADY IN USE
The given username was already used by another user.
Try giving another username.
12897
NO ENDPOINTS DEFINED UNDER ROUTE
Operation cannot be done because there are no endpoints
created under given route. Create at least one endpoint
under route and try again.
12898
UPDATING USER DATA TO DATABASE FAILED
Updating of user data to database failed. Possible reason
could be full database.
12899
SIGNALING AND DATA CHANNEL IS NOT IN SAME
ACCESS
Signaling and data channel must be in the same access.
Check the information of the route and signaling channel.
12900
GIVEN DIRECTORY NUMBER ALREADY EXISTS
The given directory number was already in use. Try giving
another number.
12901
SIGNALLING CHANNEL MISMATCH
Given signalling channel information do not tally with the
information of the route found in the system. Please check
the information of the signalling channel and try again. In
some case you can also give the command without
signalling channel.
Issue: 30-0
DN987378
519
Error messages
General Error Messages of System
12902
GIVEN PRIMARY NUMBER DOES NOT EXIST
The given primary number of the user did not exist. Define
a primary number that exists for the user.
12903
USER NAME COULD NOT BE FOUND
No user with the given name could be found. Check the
user name.
12904
MAXIMUM AMOUNT OF O&M LINKS IN USE
Maximum amount of O&M links per BCSU are in use.
12905
TOO MANY O&M LINKS PER BCF ID
Too many O&M links per BCF ID are in use.
12906
DATABASE OBJECT NOT CHANGED
This error code is used when a modification transaction
ends abnormally (controlled, not with abort).
12907
PXRECE HAS NOT ACKNOWLEDGED UPDATING
REQUEST OF DISTRIBUTION TABLE
Pxrece has not acknowledged the updating request of
distribution table made by the ABIPRB.
12908
ABIPRB HAS NO TIME FOR REQUESTED TASK
The ABIPRB is busy. It has no time for the requested task.
12909
REQUESTED OPERATION NOT DEFINED FOR OBJECT
CLASS OR ATTRIBUTE
The requested operation was not defined for the object
class or attribute.
12910
ATTRIBUTE VALUE SUPPLIED MORE THAN ONCE IN
REQUEST
An attribute value was supplied more than once in the
request.
12911
CREATION WITH REFERENCE OBJECT NOT
SUPPORTED
A reference object was supplied but creation with a
reference object is not supported.
12912
OBJECT CONTAINS OTHER OBJECT INSTANCES
An object cannot be deleted because it contains other
object instances.
12913
520
ATTRIBUTE SUPPLIED FROM PACKAGE THAT
CANNOT BE INSTANTIATED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
An attribute value was supplied for an optional attribute
from a package that cannot be included in the object
instance.
12914
NO WORKSTATION USER MMI APPLICATION SESSION
The given workstation user does not have a session at the
moment. I.e. the user has not logged in. (used in
NTN/DXT)
12915
VPCE WAS DELETED BUT COULD NOT RELEASE
VPTP
While deleting a Virtual Path Connection Endpoint, an
attempt to release the corresponding Virtual Path
Termination Point failed.
12916
SUBSCRIBER IS NOT REGISTERED
Service is not executed, because subscriber has not
registered into the system.
12917
RESERVING SOFTWARE CONFIGURATION
OPERATION IS NOT ALLOWED
The reservation of resources for the desired software
configuration operation is not permitted, because another
operation is running and prevents a new simultaneous
reservation, or the attempted operation is already
reserved, and a duplicate reservation is not possible. Use
the MML command WXP to display the operation
execution conditions, and the command WXI to see the
reservation situation. You may also have been left with a
hanging reservation in some uncontrollable error situation
(eg. a spontaneous restart of OMU, or an interrupted MML
session), and this reservation interferes with the execution
of a new operation. You can suspect a hanging
reservation, if the start time of an operation is unusually
long compared to the time it normally takes to execute this
operation. Release this kind of hanging reservation, using
the MML command WX.
12918
UNKNOWN SOFTWARE CONFIGURATION OPERATION
The requested task cannot be performed, because the SW
operation specified in the request is unknown.
12919
UNKNOWN TYPE OF SERVICE REQUEST
The service request given to the SW configuration
administration is unknown.
12920
Issue: 30-0
SW CONFIGURATION OPERATION IS NOT ALLOWED
DUE TO FORCED RESERVATION
DN987378
521
Error messages
General Error Messages of System
The given software configuration operation is not
permitted, because there is a forced reservation on the
attempted operation and a new reservation is therefore not
possible. Forced reservation is made manually using the
MML command WXE. Operation execution conditions and
reservation situation may be interrogated using MML
commands WXI and WXP. You can release the forced
reservation using the WXF command.
12921
RESOURCE CANNOT BE RELEASED BECAUSE IT IS
NOT FOUND IN RESERVATION DATA
The resource of software configuration administration
cannot be released because it cannot be found in the
reservation data.
12922
RIGHT LIST IS FULL
Subscribers or WS users right list is full (adding more
items to the list is impossible).
12925
THE CELL RATE REQUESTED CANNOT BE PROVIDED.
The cell rate requested is greater than available cell rate.
12926
TIME SUPERVISION ON READING DISK DIRECTORY
The reading of the disk directory failed, because the time
supervision expired.
12927
SET NAME IS NOT UNIQUE
An attempt was made to create a configuration set with
duplicate name. Give a unique name for the set.
12928
ALL CONFIGURATION SETS IN USE
Creation of configuration set failed, because the maximum
amount of configuration sets have already been created
and a new set could therefore not be allocated. Delete one
of the existing sets to enable the creation of a new one.
12929
CONFIGURATION SET DOES NOT EXIST
There is no configuration set that has the given name.
12930
OPERATION NOT ALLOWED
Configuration command was rejected because its
execution is not permitted.
12931
RESOURCE DOES NOT EXIST
No resource with the given name and unit type exist.
12932
522
VALUE IS OUT OF LIMITS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Modification of a resource failed because the given value
was not inside the predefined quantity limits of the
resource in question.
12933
MEMORY SHORTAGE DURING THE ACTIVATION OF A
CONFIGURATION SET
Activation of the configuration set was not possible
because a memory shortage was detected in some unit
type.
12934
ULAPRB IS BUSY
ULAPRB is busy.
12935
INFORMATION DOES NOT EXIST
The searched-for information does not exist.
12936
VIRTUAL SUBSCRIBER FOR INTERNAL USE
Virtual subscriber for internal use.
12937
ANALYSIS RESULT CORRUPTED
The analysis result is corrupted.
12939
SWITCHING OF DISK UPDATING STATE INTERRUPTED
The attempt to switch the state of disk updating has been
interrupted by the system, and the state has been reset to
as it was before.
12940
DISK UPDATING STATE PREVENTED
The attempt to switch the state of disk updating has been
interrupted by the system.
12941
DISK UPDATING STATE IS INCORRECT
Disk updating state is incorrect.
12942
TM SUBSCRIBER DOES NOT EXIST
The searched-for TM subscriber does not exist.
12943
NO ALARMS FOUND IN ALARM HISTORY
There are no alarms in the alarm database BAIDAT.
12944
ALL ALARMS READ FROM THE DATABASE
All active alarms or alarm history have been read from the
database BAIDAT.
12945
Issue: 30-0
ALARM DOES NOT EXIST
DN987378
523
Error messages
General Error Messages of System
The alarm or alarms by the given conditions do not exist in
the database.
12946
PID NUMBER LIMIT REACHED
The maximum number of alarm process instance
identifiers for one alarm_number in the alarm database
has been reached.
12947
ALARM PID EXISTS
The given process instance identifier already exists in the
alarm database.
12948
ALARM PID DOES NOT EXIST
The searched process instance identifier does not exist in
the alarm database.
12949
RECOVERY OF DUCFIL NOT SUCCESSFUL
The recovery of DUCFIL file failed because its state is not
correct.
12950
DUCFIL COULD NOT BE OPENED OR INITIALISED
DUCFIL file could not be opened or initialised.
12952
COULD NOT UPDATE DIRECTORY NUMBER DATA
The directory number data could not be updated.
12953
WORKSTATION USER CANNOT LOG IN
The workstation user cannot log in when message
requesting for monitoring arrives to database.
12954
MONITORING: WS_USER HAS NO RIGHTS
Monitoring: Ws_user has no rights.
12955
LAST WS USER IN NET WANTS TO DESELECT THE
NET
The last WS user in net under USE mode wants to leave
the net.
12956
SYNCHRONISATION IS NOT ALLOWED IN DE45/DF45
(=F, PRIMESITE) TYPE BTS
Synchronisation is not allowed in a DE45/DF45 type BTS.
The user cannot give the value Y to the SYNC parameter
when creating an adjacent cell to a DE45/DF45 type BTS.
12957
REQUESTED DIRECTORY NUMBER COULD NOT BE
FOUND
The requested directory number could not be found.
524
DN987378
Issue: 30-0
General Error Messages of System
12958
Error messages
TM SUBSCRIBER ALREADY EXISTS
A TM subscriber already exists in this exchange.
12959
RECEIVER HAS REQUESTED MODULE DURING
LOADING
The receiver has requested a new load module during the
loading. This is to say, the load sender and receiver are in
different states.
12960
FLOATING TRX NOT ALLOWED TO EXIST IN SITE
TYPE MODIFICATION
During site type modification, no floating TRXs are allowed
to exist. Remove the floating TRX and try again.
12961
E-RACH CHANNEL NOT ALLOWED TO EXIST IN SITE
TYPE MODIFICATION
No E-RACH channels are allowed to exist during site type
modification.
12962
ATTACHED MA LIST IS NOT ALLOWED IN SITE TYPE
MODIFICATION
In site type modification, an attached MA list is not allowed.
12963
RF TEST EQUIPMENT IS NOT ALLOWED TO EXIST IN
SITE TYPE MODIFICATION
RF test equipment is not allowed to exist during site type
modification.
12964
TOY CLOCK INOPERABLE
TOY clock (Time Of Year clock) is not in operable state.
12965
TOY CLOCK TIME LOST
TOY clock (Time Of Year clock) has stopped.
12966
TOY CLOCK DISABLED
TOY clock (Time Of Year clock) is disabled and the time
indicated by it is therefore unreliable.
12967
E-TRX IS NOT ALLOWED TO EXIST IN SITE TYPE
MODIFICATION
E-TRX is not allowed to exist in site type modification.
12968
RF HOPPING IS NOT ALLOWED IN SITE TYPE
MODIFICATION
RF hopping is not allowed in site type modification.
12969
Issue: 30-0
SMSC OR GT ANALYSIS DOES NOT EXIST
DN987378
525
Error messages
General Error Messages of System
There is no SMSC or GT analysis for the new SMSC
address.
12970
TOY CLOCK UPDATE FAILED
The updating of TOY clock (Time Of Year clock) has failed.
12971
ERROR WHILE MOVING DATA FROM FALLBACK COPY
LOG FILE
An error has occured while moving data from the fallback
copy log file to buffer.
12972
ERROR WHILE HANDLING FALLBACK COPY LOG FILE
An error has occured while trying to handle fallback copy
log file.
12973
FALLBACK COPY LOG FILE IS INCOMPLETE
Fallback copy log file is incompleted: the last record of log
file is corrupted.
12974
UNKNOWN RECORD VALUE IN FALLBACK COPY LOG
FILE
An unknown record value appeared in the fallback copy
log file. The log file is corrupted.
12975
NO FALLBACK COPYING IN PROGRESS
There is no fallback copying in progress.
12976
QUITTING OF FALLBACK COPYING IS IN PROGRESS
Quitting of fallback copying is already in progress.
12977
TRX DOES NOT SUPPORT HALF RATE CHANNELS
The half rate support is not activated.
12978
BAD USERNAME OR PASSWORD
FTP does not accept a connection request from a remote
FTP client because the username or password is incorrect.
12979
BAD DIRECTORY NAME
The name of the directory is incorrect.
12980
PXRECE HAS NOT ACKNOWLEDGED UPDATING
REQUEST TO SYIPRB
The PXRECE has not acknowledged the updating request
of the distribution table of the SYIPRB.
12981
526
BAD FTP PORT VALUE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The value of the PORT command is incorrect.
12982
BAD FTP TYPE VALUE
The value of the FTP type is incorrect.
12983
BAD FTP STRUCTURE VALUE
The value of the FTP structure is incorrect.
12984
BAD FTP MODE VALUE
The value of the FTP mode is incorrect.
12985
FTP DATA CONNECTION FAILED
The FTP data connection failed.
12986
FTP FILE BUSY
The FTP file is temporarily busy.
12987
FTP FILE NOT FOUND
The requested FTP file does not exist or the path name is
incorrect.
12988
FTP DIRECTORY NOT FOUND
The FTP directory does not exist or the path name is
incorrect.
12989
BAD FTP FILE NAME
The FTP file name is incorrect.
12990
BAD FTP FILE SIZE
The allocated file size for the file to be written is too small.
12991
NO FTP FILE ACCESS
No FTP file access.
12992
FTP FILE IS UNAVAILABLE
The FTP file is unavailable.
12993
BAD FTP FILE ALLOCATION
The allocation of the FTP file is incorrect.
12994
ROUTE OR CIRCUIT GROUP HAS A TIMER INDEX
ATTACHED
Route or circuit group cannot be deleted if there is a timer
index attached to it. Remove the timer index first, using the
MML command CTR.
Issue: 30-0
DN987378
527
Error messages
General Error Messages of System
12995
ISDN TRX IS NOT ALLOWED TO EXIST IN SITE TYPE
MODIFICATION
If the destination site type is Nokia 2nd generation, ISDN
TRX is not allowed to exist in site type modification.
12996
MAXIMUM NUMBER OF TRX IDS ALREADY IN USE
The maximum number of TRX IDs is already in use.
12997
CREATION OF HAND HAS FAILED IN SYIPRB
The creation of a hand has failed in the SYIPRB probably
because of an operating system error.
12998
SYIPRB HAS NO TIME FOR REQUESTED TASK
The SYIPRB is busy. It has no time for the requested task.
12999
PXRECE HAS NOT ACKNOWLEDGED UPDATING
REQUEST OF SYIPRB
The PXRECE has not acknowledged the updating request
of the distribution table made by the SYIPRB. The SYIPRB
has cancelled an ongoing switchover.
13000
TRX ID UNKNOWN
A configuration mismatch has been found between
GUPDAT and Abis signalling program blocks, or a
message was corrupt.
13001
RECOVERY PROGRAM BLOCK DOES NOT CONTROL
UNIT RESTART
The unit is restarting, and the recovery program block
RCXPRO cannot control its loading.
13002
UNIT OVERLOAD
The unit working as the source of loading cannot give
loading permission because the unit is overloaded.
13003
LOADING PARAMETERS ARE NOT VALID
The parameters for initial loading and file loading are
missing or they are not valid.
13004
CBCH MOBILE ALLOCATION OVERFLOW OR C2 CELL
RESELECTION ACTIVE IN SYSINFO 4
SYSINFO 4 has no space for the C2 cell reselection
parameter because the CBCH mobile allocation list
includes too many values.
13005
528
FREQUENCY VALUE ZERO IN ABIS INTERFACEINTERNAL ARFCN TABLE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The internal ARFCN table of the Abis interface includes a
frequency value zero.
13006
FREQUENCY BAND UNKNOWN
The frequency band was not GSM or DCS.
13007
TOO MANY ARFCN VALUES (RANGE 256)
The creation of range 256 fails because of too many
ARFCN values.
13008
TOO MANY ARFCN VALUES (RANGE 512)
The creation of range 512 fails because of too many
ARFCN values.
13009
TOO MANY ARFCN VALUES (RANGE 1024)
The creation of range 1024 fails because there are too
many ARFCN values.
13010
USE OF THIS RANGE NOT ALLOWED
The use of this range has been barred by UTPFIL.
13011
CELL ALLOCATION IS NOT AVAILABLE
The length of the cell allocation table is zero.
13012
TOO MANY VALUES IN THE CELL ALLOCATION TABLE
The length of the cell allocation table is greater than
allowed.
13013
VALUE ZERO IN CELL ALLOCATION TABLE
There is a frequency value zero in the cell allocation table.
13014
INVALID VALUE IN THE CELL ALLOCATION TABLE
There is an invalid ARFCN value in the cell allocation
table.
13015
SAME ARFCN VALUE TWICE IN CELL ALLOCATION
TABLE
The same ARFCN value occurs twice in the cell allocation
table.
13016
TOO MANY ARFCN VALUES OR TOO BIG DIFFERENCE
BETWEEN GREATEST AND SMALLEST VALUE
There is an overflow in the Abis interface-internal ARFCN
table.
13017
Issue: 30-0
MOBILE ALLOCATION IS NOT AVAILABLE
DN987378
529
Error messages
General Error Messages of System
The length of the mobile allocation table is zero.
13018
TOO MANY VALUES IN THE MOBILE ALLOCATION
TABLE
The length of the mobile allocation table is greater than
allowed.
13019
ZERO VALUE IN THE MOBILE ALLOCATION TABLE
There is a frequency value zero in the mobile allocation
table.
13020
INVALID VALUE IN THE MOBILE ALLOCATION TABLE
There is an invalid ARFCN value in the mobile allocation
table.
13021
SAME ARFCN VALUE TWICE IN MOBILE ALLOCATION
TABLE
The same ARFCN value occurs twice in the mobile
allocation table.
13022
DIFFERENCE BETWEEN GREATEST AND SMALLEST
FREQUENCY IS TOO BIG (BM0)
The creation of bit map 0 format fails because the
difference between the greatest and the smallest ARFCN
value is too big.
13023
TOO MANY ARFCN VALUES (BM0)
The creation of the bit map 0 format fails because of too
many ARFCN values.
13024
TOO MANY ARFCN VALUES (VBM)
The creation of variable bit map format fails because of too
many ARFCN values.
13025
DIFFERENCE BETWEEN GREATEST AND SMALLEST
FREQUENCY IS TOO BIG (VBM)
The creation of variable bit map format fails because the
difference between the greatest and smallest ARFCN
value is too big.
13026
DIFFERENCE BETWEEN GREATEST AND SMALLEST
FREQUENCY IS TOO BIG (RANGE 256)
The creation of range 256 fails because the difference
between the greatest and smallest ARFCN value is too
big.
13027
530
DIFFERENCE BETWEEN GREATEST AND SMALLEST
FREQUENCY IS TOO BIG (RANGE 512)
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The creation of range 512 fails because the difference
between the greatest and smallest ARFCN value is too
big.
13028
NO SYSTEM INFORMATION ACKNOWLEDGEMENT
MESSAGES RECEIVED FROM LAYER 2
SYIPRB has not received system information
acknowledgement messages from the layer 2.
13029
WRONG VALUE OF THE PARAMETER
NEIGH_CELL_RANGE_LIMITS_PRM_C
The value of the neigh_cell_range_limits_prm_c parameter
is incorrect. The value must be between 0 and 7.
13030
BTS ID UNKNOWN
A configuration mismatch has been found between
GUPDAT and Abis signalling program blocks, or a
message was corrupt.
13031
THE SUM OF PERCENTAGE RATES ON REMNANT
TRAFFIC DISTRIBUTION DIFFERS FROM 100
The sum of percentage rates on remnant traffic distribution
of all carrier access codes in use differs from 100. Correct
the percentage rates so that the sum total equals 100%.
13032
MISSING PIU TYPE INFO
Correct data on plug-in unit type cannot be read from HW.
13033
MISSING PIU UNIQUE INFO
The unique identification data for the plug-in unit cannot be
read from HW.
13034
UNSUPPORTED FTAM SERVICE CLASS
Unsupported FTAM service class. The corresponding
FTAM diagnostic code is 2002 and it is an associationrelated diagnostics notice, defined in ISO 8571-3.
13035
FTP COMMAND NOT SUPPORTED
The FTP command is not supported.
13036
FTP ARGUMENT NOT SUPPORTED
The FTP argument is not supported.
13037
Issue: 30-0
ILLEGAL ADDRESS INFO OF PLUG-IN UNIT IN
EQUIPMENT DATABASE
DN987378
531
Error messages
General Error Messages of System
The address information that is given about the plug-in unit
in the equipment database is incorrect or incompatible with
the plug-in unit type.
13038
DISTRIBUTION ABOUT CHANGE IN DATABASE FAILED
The database has been updated, but distribution has
failed.
13044
V5.1-MUX SUBSCRIBER
This subscriber is connected to the concentrator via a
V5.1-MUX interface.
13045
COMMUNICATION ERROR IN DSP PROCESSOR
An error has occurred in the communication between the
DSP processor and the processor controlling it.
13046
NO SUCH V5.1-MUX SUBSCRIBER
There is no V5.1-MUX subscriber of the given type in the
user port database.
13047
GIVEN USERNAME IS NOT DEFINED IN THE
EXCHANGE
This error code is given when a workstation user tries to
start a session (login) and the given username is not
known by the DXT exchange. The username check is
made together with the password check. (in NTN/DXT)
13048
EVENT LOG STREAM IS OPEN ON DAT
The given event log stream is open to DAT tape. To delete
this event log stream, you must first close it on DAT, using
the MML command DLC.
13049
ANALYSIS RESULT NON-EXISTENT
The analysis result does not exist.
13050
ANALYSIS RESULT EXISTS
The analysis result already exists.
13051
ENTERED DATA NOT IN ENCRYPTED FORM
The entered data (e.g. the cryptographic key) was in clear
form although it is expected to be in encrypted form.
Encrypt the data and re-enter it.
13052
CHECK SUM OF LOAD MODULE IN LOAD CHAIN IS
INCORRECT
The check sum of the load module is incorrect.
532
DN987378
Issue: 30-0
General Error Messages of System
13053
Error messages
MODULE NAME OF LOAD MODULE IN LOAD CHAIN
DOES NOT MATCH THE NAME IN BOOLIS
The module name of the load module does not match the
name in BOOLIS. The order of the modules is different in
the memory and in BOOLIS.
13054
HIGH TAG OF LOAD MODULE IN LOAD CHAIN IS
INCORRECT
The high tag of the load module is incorrect.
13055
LOW TAG OF LOAD MODULE IN LOAD CHAIN IS
INCORRECT
The low tag of the load module is incorrect.
13056
LINK FIELD OF LOAD MODULE IN LOAD CHAIN IS
INCORRECT
The link field of the load module is incorrect.
13057
ISDN O&M LINK IS NOT ALLOWED TO EXIST IN SITE
TYPE MODIFICATION
The modification of site type does not allow the ISDN O&M
link to exist.
13058
FTP OPERATION EXECUTED PARTLY OK
The execution of the FTP operation has been partly
successful.
13059
FTP FILE HAS BEEN READ
The FTP file has been read.
13060
FNIM INCLUDES EXTERNAL LINES IN NTN DATABASE
Because FNIM external line definition is found from NTN
Database, removing of FNIM is not allowed.
13061
FNIM IS NOT FOUND FROM NTN DATABASE
The FNIM definition is not found from NTN database.
13062
PREVIOUS INDEX NOT FOUND IN THE DB
Prev_index is used to indicate the current position of the
record in the database, when reading the data in more
than one part. The record of the prev_index is probably
deleted between the reads.
13063
WS_USERNAME IS UNKNOWN
The given WS_USERNAME is not found in the database.
13064
Issue: 30-0
DISTRICT_ID IS UNKNOWN
DN987378
533
Error messages
General Error Messages of System
The given district_id is unknown.
13065
FTP DATA CONNECTION CLOSED
The FTP data connection failed because the FTP client
closed the connection.
13066
FTP LOCAL FAILURE
The FTP command failed because of a local failure in the
server process. The failure probably appeared from the
disk system. Check the logs of the SFTPAT process.
13067
UNIT STATE HAS TO BE WO BECAUSE IT HAS
EXCHANGE TERMINALS TO SUPERVISE
The working state of the unit has to be active (WO)
because it has exchange terminals to supervise.
13068
UNIT STATE HAS TO BE WO BECAUSE IT HAS
PREPROSESSORS TO SUPERVISE
The working state of the unit has to be active (WO)
because it supervises preprosessor(s) behind an LAPDchannel.
13069
UNIT STATE HAS TO BE SP BECAUSE IT HAS NO
PREPROSESSORS TO SUPERVISE
The working state of the unit has to be passive (SP)
because it has no preprosessors behind an LAPD-channel
or other resources to supervise.
13070
UNIT STATE HAS TO BE WO BECAUSE IT HAS CCS7
SIGNALLING LINKS
The working state of the unit has to be active (WO)
because it has CCS7 signalling links.
13071
UNIT STATE HAS TO BE SP BECAUSE IT HAS NO
CCS7 SIGNALLING LINKS
The working state of the unit has to be passive (SP)
because it has no CCS7 signalling links or resources to be
supervised.
13072
UNIT STATE HAS TO BE ACTIVE (WO)
The state of the unit must be active (WO). If you need to
force another working state for the unit, use the MML
command USC, its parameter FCD.
13073
UNIT STATE HAS TO BE PASSIVE (SP)
The state of the unit has to be passive (SP). If you need to
force another working state for the unit, use the MML
command USC, its parameter FCD.
534
DN987378
Issue: 30-0
General Error Messages of System
13074
Error messages
THE LAST (N+1) REPLACEABLE REDUNDANT SPARE
UNIT CANNOT BE ACTIVATED
The unit cannot be activated, otherwise no redundancy
remains to provide fault tolerance.
13075
FNIM EXTERNAL LINE HAS PARAMETER DEFINITION
Before FNIM plug-in unit can be removed, the line specific
parameter definition must be removed.
13076
INCORRECT PROTOCOL USED
An incorrect protocol has been used. It is eg. possible that
you have tried to use locally (in your own unit) a remote
protocol that is meant to be used from another unit.
13077
NO REPLY FROM SIGNALLING
Central Memory (CM) has sent a request to signalling but
there was no reply within the given time limit. Try again.
13079
PACKAGE NAME IS ALREADY IN USE
A package named like this has already been created (in
the SOMAFI file).
13080
BU-PACKAGE IS MISSING IN FALLBACK COPY
Fallback copying is not possible because a BU-package is
missing.
13081
UNIT STATE HAS TO BE SP BECAUSE IT HAS NO
EXCHANGE TERMINALS TO SUPERVISE
The working state of the unit has to be passive (SP)
because it has no exchange terminals or other resources
to supervise.
13082
PACKAGE IDENTIFIERS DO NOT MATCH BETWEEN
BU- AND FB-PACKAGE
The execution of the ARCHIVE or DATA fallback copy is
not possible because package identifiers do not match
between the BU- and FB-package.
13083
NOT ENOUGH DISK SPACE
There is not enough free disk space to execute fallback
copy.
13084
Issue: 30-0
GIVEN OPTIONAL DIRECTORY NAME IS NOT
ALLOWED
DN987378
535
Error messages
General Error Messages of System
The name given for the optional directory is not allowed,
because the same name is already in use. Either it has
been given before or the name is reserved by the system
(ASWDIR, BLCODE, LFILES, MMDIRE or SCMANA).
13085
FALLBACK COPY IS NOT POSSIBLE: FB-PACKAGE
MISSING
Fallback copying is not possible because FB-package is
missing.
13086
INCORRECT WORKING STATE ON DISK
Operation is not possible because the working state of the
disk is incorrect: the working state has to be WO-BU.
13087
INCORRECT WORKING STATE OF THE DISK UNIT
Fallback copying is not possible because the state of the
disk unit is incorrect: the working state has to be SE-NH or
WO-EX.
13088
FALLBACK COPYING IS NOT POSSIBLE BECAUSE OF
MISSING SUBDIRECTORY
Fallback copying (of DATA or ARCHIVE) is not possible
because the subdirectory given in the BU-package is
missing in the FB-package.
13089
FALLBACK COPY IS NOT POSSIBLE BECAUSE FBPACKAGE IS DEFAULT PACKAGE
Fallback copying is not possible because the FB-package
is the default package.
13090
REMOVE ALL THE OTHER FNIM CARDS FIRST
Before SBCN can be removed from FNIM, all the other
cards must be removed.
13091
PACKAGE ALREADY EXISTS IN DIRECTORY
Fallback copying is not possible to the given directory,
because a package has already been created for the
directory.
13092
ADDING THIS TYPE OF PLUG-IN UNIT IN FUTURE
RELEASE
This type of plug-in unit can be added in future release.
13093
INVALID UNIT TYPE
Type of unit is not correct for the operation.
13094
536
SUBSCRIBER HAS NOT THE GIVEN HLR ADDRESS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The HLR address of the subscriber in the database is
different from the HLR address given in the search criteria.
13095
FNIM EXTERNAL LINE NOT IS FOUND IN NTN
DATABASE
The external line definition is not found in NTN database.
13096
LINE PARAMETER IS NOT DEFINED TO FNIM
EXTERNAL LINE
The FNIM external line does not have line specific
parameters in NTN database.
13097
DISTRIBUTION NOT DONE
File or record distribution was not done.
13098
DEFAULT VALUE IS MISSING
Default value is missing.
13099
INDEX VALUE OF FUNCTIONAL UNIT IS TOO HIGH
The value of the functional unit is too high.
13100
ENHANCED RAPID FIELD DROP OPTION IS NOT IN
USE IN BSC
The option Enhanced Rapid Field Drop is not in use in
BSC. The basic idea of this feature is to detect the Deep
Dropping Edge of the serving cell signal and perform a
handover to the appropriate adjacent cell.
13101
ICE OPTION IS NOT IN USE IN BSC
The basic idea of this feature is to provide handover
support for BTSs having transceivers of different
transmitting power. This error code indicates that the
option is not in use.
13102
APPLICATION DOES NOT RESPOND TO EVENT LOG
Application does not respond to event log. This error can
occur for example in recovery, when event logs are run
and the application does not acknowledge recovered data.
13103
REFERENCE HOME AREA DOES NOT EXIST
The reference home area cannot be found from the home
area files.
13104
LAST LOCATION AREA IN HOME AREA
The location area is the last one in the home area.
13105
Issue: 30-0
HOME AREA DOES NOT EXIST
DN987378
537
Error messages
General Error Messages of System
The home area cannot be found from the home area files.
13106
HOME AREA ALREADY EXISTS
The home area already exists in the home area files.
13107
HOME AREA CONTAINS SUBSCRIBERS
The home area contains subscribers.
13108
LOCATION AREA DOES NOT CONTAIN BASE
TRANSCEIVER STATIONS
The location area does not contain base transceiver
stations.
13109
VIRTUAL MACHINE NUMBER NON-EXISTENT
The Virtual Answer Machine number is not in use.
13110
USER DELETION IN PROGRESS
E.g. A new subscriber could not be created because its
deletion is in progress.
13111
OPTION HSCSD NOT IN USE IN BSC
The High Speed Circuit Switched Data (HSCSD) option is
not in use in BSC. The HSCSD offers a remarkable
increase in the data rate over the GSM system.
13112
DYNAMIC HOT SPOT OPTION IS NOT IN USE IN BSC
This feature is designed to control traffic in a frequency
hopping radio network on the basis of the interference and
hence achieve the higher radio network capacity. Dynamic
Hot Spot -error code indicates that the option is not in use.
13113
MF FUNCTION STATISTICAL COUNTER NOT FOUND
SEARCHING BY SEQUENCE NUMBER
The statistical counter of the MF function is not found when
searched using the sequence number of the MF function.
13114
MF FUNCTION STATISTICAL COUNTER NOT FOUND
SEARCHING BY PIU FUNCTION
The statistical counter of the MF function cannot be found
when the PIU function is given as the search key.
13115
PROCESSING IN APPLICATION ALARM HANDLER HAS
FAILED
The application alarm handler failed to process the task
(e.g. saving alarm parameters or cancelling or blocking an
alarm).
538
DN987378
Issue: 30-0
General Error Messages of System
13116
Error messages
OPTIONAL FEATURES FORMING THIS COMMAND
GROUP ARE NOT INCLUDED IN DELIVERY
This command group consists of optional features which
are not included in this delivery.
13117
LOCATION AREA NOT FOUND OR DOES NOT
CONTAIN BASE TRANSCEIVER STATIONS
Location area/areas not found in LAFILE, or location
area/areas do not contain any BTSs.
13118
LOAD LIST IS NOT DEFINED
The load list has not been defined.
13119
SUPER-REUSE FREQUENCY GROUP OF TRX IS
INCORRECT
When frequency hopping and Intelligent Underlay Overlay
are in use, all the unlocked TRXs of the layer must belong
to the same super-reuse frequency group.
13120
ONE OR MORE ILLEGAL CHANNEL TYPES
There was one or more channel types other than COMB,
MAIN, SDCCH, TCHF, BCCH_CBCCH, SDCCH_CBCH,
NOT_IN_USE or E_RACH.
13121
ILLEGAL BCCH LOCATION
BCCH was in a time slot other than RTSL 0.
13122
TCSM NOT FOUND
The TCSM is not found.
13123
ILLEGAL E-RACH LOCATION
E-RACH was in a time slot other than RTSL 0.
13124
TOO MANY BCCH TRXS
Only one broadcast control channel TRX is allowed in one
cell.
13125
ILLEGAL SDCCH-CBCH LOCATION
SDCCH-CBCH can only be located in a BCCH TRX.
13126
SDCCH WAS NOT FOUND IN BCCH TRX
A BCCH TRX must contain an SDCCH.
13127
TOO MANY SDCCH SUBCHANNELS
There can be only 12 SDCCH subchannels in one TRX.
Issue: 30-0
DN987378
539
Error messages
General Error Messages of System
13128
TOO MANY CBCH CHANNELS
Only one CBCH channel is allowed in one TRX.
13129
ILLEGAL TIME SLOT FOR SDCCH-CBCH
SDCCH-CBCH can be in time slots 1 - 3.
13130
ILLEGAL SITE TYPE FOR E-RACH
This site type cannot have an E-RACH.
13131
ILLEGAL BCCH DEFINITION: E-TRX AND S-TRX
CANNOT CONTAIN BCCH
ILLEGAL BCCH DEFINITION: E-TRX AND S-TRX
CANNOT CONTAIN BCCH
13132
ILLEGAL E-RACH LOCATION: IT MUST BE IN E-TRX OR
S-TRX
ILLEGAL E-RACH LOCATION: IT MUST BE IN E-TRX OR
S-TRX
13133
WRONG NUMBER OF E-RACH CHANNELS IN E-TRX
OR S-TRX
WRONG NUMBER OF E-RACH CHANNELS IN E-TRX
OR S-TRX
13134
WHEN E-TRX OR S-TRX IS USED, TIMESLOT 1 OF
BCCH TRX MUST BE OF TYPE NOTUSED
WHEN E-TRX OR S-TRX IS USED, TIMESLOT 1 OF
BCCH TRX MUST BE OF TYPE NOTUSED
13135
INITIALSWVERSION IS NOT ONLY ATTRIBUTE TO BE
ASKED
The INITIALSWVERSION and other attributes are asked
at the same time.
13136
3-DIGIT MOBILE NETWORK CODE OPTION IS NOT IN
USE IN BSC
The 3-Digit Mobile Network Code feature is based on ANSI
specifications. If the option is not activated, MNC is
handled with 2 digits.
13137
INTEGRITY CHECKING IN MEMORY IS NOT ALLOWED
Integrity checking in memory is not allowed for the
requested database.
13138
INTEGRITY CHECKING ON DISK IS NOT ALLOWED
Integrity checking on disk is not allowed for the requested
database.
540
DN987378
Issue: 30-0
General Error Messages of System
13139
Error messages
ALL SDCCH HANDS OF ABIPRB ARE TEMPORARILY IN
USE
All SDCCH hands of the ABIPRB are temporarily in use the TRX configuration command can be repeated after a
while.
13140
MAXIMUM NUMBER OF LOCATION AREAS IN HOME
AREA EXCEEDED
The maximum number of location areas (96) in home area
exceeded in the creation of a new home area.
13141
DATA LENGTH IN MID DATA MESSAGE WAS INVALID
The data length given in the mid_data message was
invalid.
13142
FREQUENCY HOPPING FOR INTELLIGENT UNDERLAY
OVERLAY OPTION IS NOT IN USE IN BSC
The Frequency Hopping for Intelligent Underlay Overlay is
an optional feature designed to allow the operator to reuse
frequencies more intensively and hence achieve a higher
radio network capacity. This error code indicates that the
feature is not in use.
13143
BSC OBJECT NOT FOUND IN RADIO NETWORK
DATABASE
The access node has not been created into the radio
network database. No other objects can created before the
BSC object has been created.
13144
BCF OBJECT NOT FOUND IN RADIO NETWORK
DATABASE
The Base Control Function object has not been created
into the database. There must be an existing BCF under
which a base station object can be created.
13145
TOO MANY INTERFERING CELLS DEFINED TO
FREQUENCY GROUP
Too many interfering cells have been defined to the
frequency group. The frequency group is defined by the
parameter FRT of the TRX so that all TRXs that have the
same FRT belong to the same frequency group.
13148
BTS NOT FOUND FROM RADIO NETWORK DATABASE
The base station has not been created into the radio
network database. There must be an existing BTS under
which a transceiver, a frequency hopping system, or an
adjacent cell object can be created.
Issue: 30-0
DN987378
541
Error messages
General Error Messages of System
13149
TRX NOT FOUND IN RADIO NETWORK DATABASE
The transceiver has not been created into the radio
network database. There must be an existing TRX under
which a radio time slot can be created.
13150
RADIO TSL NOT FOUND IN RADIO NETWORK
DATABASE
The radio time slot has not been created into the radio
network database.
13151
HOPPING SYSTEM NOT FOUND IN RADIO NETWORK
DATABASE
The Frequency Hopping System has not been created into
the radio network database. There must be an existing
FHS into which a hopping radio time slot can be
connected.
13152
ADJACENT CELL WAS NOT FOUND IN RADIO
NETWORK DATABASE
The adjacent cell has not been created into the radio
network database.
13153
MA LIST NOT FOUND IN RADIO NETWORK DATABASE
The MA list must be created before any BTS can be
attached to it.
13154
WSU IS FULL, NO MORE TRANSCEIVERS CAN BE
CREATED IN SAME UNIT
The maximum number of transceivers allowed in the
signalling unit has been reached. A D-channel in another
WSU should be used.
13155
ALL CPUS MUST BE CP4HX IF MORE THAN 16 TRXS
IN WSU
All CPUs must be of type CP4HX if there are more than 16
TRXs in WSU.
13156
GSWB MUST BE INSTALLED WHEN MORE THAN 16
TRXS IN WSU
GSWB must be installed when there are more than 16
TRXs in one WSU.
13157
TOO FEW AS7-U PLUG-IN UNITS WHEN MORE THAN
16 TRXS IN WSU
There are only three AS7-U plug-in units in all WSUs when
there are more than 16 TRXs in one WSU.
542
DN987378
Issue: 30-0
General Error Messages of System
13158
Error messages
TOO FEW WSUS IN WO-EX STATE WHEN MORE THAN
16 TRXS IN WSU
Eight WSUs in WO-EX state when there are more than 16
TRXs in one WSU.
13159
TOO MANY TCHS IN ONE WSU
Maximum number of traffic channels exceeded in one
WSU.
13160
THERE ARE TOO MANY BCFS IN ONE WSU
When creating a BCF (site type B or D), or when creating a
TRX (site type F), or when modifying the O&M-link, it
became evident that there will be too many BCFs in one
WSU.
13161
MAXIMUM TX POWER OF CELL TOO HIGH DUE TO
ATTENUATED CHANNELS GSM800
If the frequency band used is GSM800 band, the two
channels next to the edge channels of the block must not
be used with the maximum transmission power. The FCC,
the local regulator in the USA, has set these emission
limits for GSM800 band equipments to ensure that an
operator on a certain band does not cause disturbance to
another operator on adjacent bands.
13162
INITIAL BTS BUILD IS NOT FOUND
The initial build of the BTS generation is not found.
13163
BCF BUILD IS INITIAL PACKAGE
The BCF build is defined as the initial build of the BTS
generation.
13164
FNIM EXTERNAL LINE IS NOT CONNECTED TO ANY
CONNECTION GROUP
The FNIM external line does not have circuit group line
parameters in NTN database.
13165
PARAMETER SET IS ALREADY DEFINED - NO
CHANGES
If parameter set is already defined into NTN database, no
changes is made.
13166
PARAMETER SET IS NOT DEFINED IN NTN DATABASE
There is no defined parameter set in NTN database.
13167
Issue: 30-0
POSIX INTERFACE ERROR
DN987378
543
Error messages
General Error Messages of System
The call through POSIX subsystem has failed due to faulty
parameters, wrong call sequence or an internal error in the
subsystem.
13168
FNIM PLUG-IN UNIT IS NOT FOUND FROM DATABSE
Plug-in unit is not found from NTN database.
13169
FNIM EXTERNAL LINE DEFINITION IS NOT FOUND
FROM NTN DATABASE
The FNIM external definition is not found from NTN
database.
13170
EXACTLY SAME BCF HW DATABASE ALREADY
CREATED
A BCF HW database creation is requested to a database
that has already been created with the same file name and
checksum.
13171
FREQUENCY NOT ALLOWED TO BE ZERO
The value zero for frequency is not allowed.
13172
INTERFERING CELL LAC-CI NOT UNIQUE WITHIN TRX
LAC-CIs of interfering cells within one TRX must be
unique.
13173
SIMULTANEOUS BB AND RF HOPPING IS NOT
ALLOWED UNDER BTS
The operation was rejected because there is
simultaneously defined BB (baseband) and RF (radio
frequency) hopping in the BTS.
13174
ALARM FILE FULL OF ACTIVE ALARMS
The alarm file in the alarm database is full of active alarms.
13175
ALARM ALREADY EXISTS
The alarm occurrence already exists in the alarm
database.
13176
UPPER LEVEL ALARM HISTORY LINK FAILED
Upper level alarm history link is discontinuous.
13178
OPERATING INSTRUCTION ADDITION FAILED
Addition of an operating instruction to the database has
failed.
13179
OBJECT ADDITION FAILED
Addition of an object to the database failed.
544
DN987378
Issue: 30-0
General Error Messages of System
13180
Error messages
TEXT DOES NOT EXIST
No text with the given terms exists in the database.
13181
OPERATING INSTRUCTION OR FIXED TEXT EXISTS
An operating instruction or a fixed text exists.
13182
OBJECT JOINED TO ALARM
An object is joined to the alarm to be removed.
13183
OPERATING INSTRUCTION ALREADY EXISTS
An operating instruction by the given terms already exists
in the database.
13184
MASTER OBJECT IS NOT FOUND
The master object of the given child is not found.
13185
OLD CHILD IS NOT FOUND
The given old child object is not found.
13186
CHILD NOT FOUND
The given child was not found.
13187
OLD MASTER OBJECT IS NOT FOUND
The old master object of the given old child is not found.
13188
NEW MASTER OBJECT IS NOT FOUND
A new master object for a new child is not found.
13189
TREE NOT FOUND
The given tree identifier does not exist in the database.
13190
TREE ALREADY EXISTS
The given tree already exists in the database.
13191
TREE ADDITION FAILED
The addition of the tree to the database failed.
13192
OBJECT IS LOWEST
The given object is the lowest one.
13193
CHILD ALREADY EXISTS
The given child already exists in the database.
13194
Issue: 30-0
TOO MANY UNITS FOUND
DN987378
545
Error messages
General Error Messages of System
DUFLIB routines return this error code when the number of
units found exceeds the limit the caller has specified.
13195
NO UNITS FOUND
DUFLIB routines return this error code when no units with
given parameters could be found.
13196
OPERATING INSTRUCTION NOT FOUND
An operating instruction by the given terms does not exist
in the database.
13197
WRONG WORKSTATION USER PASSWORD
Wrong workstation user password is indicated.
13198
THE CIRCUIT GROUP WITH GIVEN SEARCH CRITERIA
IS NOT FOUND
The circuit group with given search criteria is not found.
13199
GATEWAY WITH GIVEN SEARCH CRITERIA IS NOT
FOUND
The gateway object with given search criteria is not found.
13200
THE PREFIX DIGITS IN THE EXTERNAL SUBSCRIBER
DO NOT MATCH ANY GATEWAY DIGITS
The prefix digits in the external subscriber do not match
any gateway digits.
13201
PASSWORD EXPIRED
User password has expired.
13202
PASSWORD IS GOING TO EXPIRE
User password is going to expire in specified time.
13203
NO AVAILABLE VPCI IS FOUND FROM GIVEN ROUTE
No available VPCI is found from the given route with
requested requirements.
13204
ADDITION FAILED
The addition to the database failed.
13205
OBJECT IS NOT LOWEST
The given object is not the lowest object.
13206
546
LAST ALARM RECEIVED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The last active_alarm_inquiry_ack_s message from
ULAPRB to ARNOLD has a status field the value of which
is the all_alarm_read_ec error code.
13207
REQUESTED TASK WAS ONLY PARTIALLY
COMPLETED
The requested task was completed only partially, due to
internal resource limitations.
13209
LINE STATE MUST BE SET TO OFF-LINE
Before line or parameter set can be removed, the state of
line must be set to OFF-LINE.
13210
FILE RESIZING IS PREVENTED
File resizing is prevented. Resizing can be done after
prevention is forced off.
13211
MISSING ENVIRONMENT
This error text concerns only the platform and indicates
that there is no application level.
13212
MASTER OBJECT IS BLOCKED
The blocking of the child is attempted, but its master object
has already been blocked.
13213
OBJECT ALREADY BLOCKED
Returned when the object to be blocked has already been
blocked.
13214
UNIT STATE MUST BE WO BECAUSE IT HAS LAPD
SIGNALLING LINKS TO SUPERVISE
The working state of the unit must be active (WO) because
it has LAPD signalling links to supervise.
13215
UNIT STATE MUST BE SP BECAUSE IT HAS NO LAPD
SIGNALLING LINKS TO SUPERVISE
The working state of the unit must be passive (SP)
because it has no LAPD signalling links or other resources
to supervise.
13216
NOT ENOUGH MEMORY TO COMPLETE THE
OPERATION
There is not enough memory to complete the operation.
Error code is received when lack of memory is observed
outside operating system kernel by system software
program or the application. This may occur for example
when the amount of free memory is checked before file
creation.
Issue: 30-0
DN987378
547
Error messages
General Error Messages of System
13217
OBJECT IS NOT BLOCKED
The object whose unblocking is attempted is not blocked.
13218
SCHEDULED BLOCK ALREADY EXISTS
The blocking which has time parameters already exists.
The function is not accepted.
13220
THE GW_ID IS OUT OF RANGE
The given gw_id is out of range.
13221
OPTION FREQUENCY HOPPING FOR IUO IS NOT
ACTIVE IN BSC
If a cell has super-reuse TRXs and one or the other layer
is hopping, the option Frequency Hopping for Intelligent
Underlay Overlay must be active in the BSC.
13222
ILLEGAL WORKING STATE
The circuit(s) cannot be changed into the given working
state.
13223
NO REPLY FROM CM
There is no reply from Central Memory (CM) to the request
to change the working state of the circuit(s).
13224
MATCHING EVENTS NOT FOUND
Inquired events were not found.
13225
FCEFIL FILE FULL
New file size changes cannot be started because FCEFIL
file is full.
13226
FCEFIL ALREADY HAS KEY VALUE
Key value cannot be added to FCEFIL file because it
already has a key value.
13227
CHARGING MODIFICATION NOT FOUND
Given charging modification was not found.
13228
CHARGING MODIFICATION RESULT NOT FOUND
Given charging modification result was not found.
13229
CHARGING MODIFICATION RESULT IN USE
The given charging modification result is in use (attached
to charging modification).
13230
548
CHARGING MODIFICATION IN USE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The given charging modification is in use (attached to
charging case).
13231
CHARGING MODIFICATION RESULT EXISTS ALREADY
Given charging modification result exists already.
13232
CHARGING MODIFICATION IDENTIFICATION
INFORMATION CONTRADICTORY
Given charging modification identification information
mutually contradictory.
13233
CHARGING MODIFICATION RESULT IDENTIFICATION
INFORMATION CONTRADICTORY
Given charging modification result identification information
is mutually contradictory.
13234
CHARGING MODIFICATION ATTRIBUTE COMBINATION
DOES NOT EXIST
Given combination of charging modification attributes does
not exist.
13235
CHARGING MODIFICATION DOES NOT CONTAIN ALL
GIVEN ATTRIBUTES
The charging modification has been given attributes that
do not belong to the charging modification in question.
13236
CHARGING MODIFICATION ATTRIBUTES IN WRONG
ORDER
The charging modification attributes are given in wrong
order.
13237
CHARGING MODIFICATION ATTRIBUTE VALUE EXISTS
ALREADY
Given value of charging modification attribute exists
already.
13238
CHARGING MODIFICATION ATTRIBUTE VALUES NOT
FOUND
Given values of charging modification attribute were not
found.
13239
CHARGING MODIFICATION ATTRIBUTE VALUE
UNKNOWN
Given value of charging modification attribute is unknown.
13240
TEST SIDE OF CHARGING MODIFICATION EMPTY
The test side of charging modification is empty.
Issue: 30-0
DN987378
549
Error messages
General Error Messages of System
13241
ALARM UPLOAD PERFORMED
The NMS has performed an alarm upload.
13242
BASIC SERVICE INCOMPATIBILITY
The basic services are incompatible.
13243
VARIANT UNKNOWN AT REMOTE END
This error code indicates that the reason for rejecting the
reprovisioning request, or the switch_over_to_new_variant
request in the V5 interface, is an unknown variant.
13244
VARIANT KNOWN, NOT READY AT REMOTE END
This error code indicates that the reason for rejecting the
reprovisioning request, or the switch_over_to_new_variant
request in the V5 interface, is a known variant which is not
ready for the requested operation.
13245
REPROVISIONING IN PROGRESS AT REMOTE END
The reason for the rejection of the reprovisioning request
or the switch_over_to_new_variant request in the V5
interface is that reprovisioning is already in progress.
13246
NO RESPONSE FROM NETWORK ELEMENT LEVEL
ALARM SYSTEM
Network element level alarm system (program block
ULAPRB) does not respond.
13247
NO ANSWER FROM REMOTE END
The remote end does not respond to a reprovisioning
request in the V5 interface.
13248
SSI USED BY SUBSCRIBER
The requested SSI is already used as a subscriber identity.
13249
SSI USED BY WORKSTATION
The requested SSI is already used as a Dispatching
Workstation identity.
13250
SSI USED BY GROUP
The requested SSI is already used as a group identity.
13251
SSI USED BY HIDDEN SUBSCRIBER
The requested SSI is already used as a hidden subscriber
identity. Creation or deletion sequence of a subscriber is
proceeding or has been aborted abnormally.
13252
550
SSI USED BY SERVICE HANDLE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The requested SSI is already used as a service handle
identity.
13253
INTELLIGENT NETWORK SUBSCRIBER
The subscriber type is Intelligent Network Subscriber
(INS).
13254
INTELLIGENT NETWORK SUBSCRIBER DOES NOT
EXIST
The searched-for Intelligent Network Subscriber (INS)
does not exist.
13256
SSI USED BY UNUSABLE GROUP
The requested SSI is already used as an identity of a
group that is in out-of-use state. The group is waiting for
deletion.
13257
PARAMETER OBJECT NOT FOUND
Organization parameter object is not found from the
database.
13258
INTELLIGENT NETWORK SUBSCRIBER (INS)
ALREADY EXISTS
The Intelligent Network Subscriber (INS) already exists.
13259
USAGE OF DATA DICTIONARY NOT INITIALIZED
CORRECTLY
Usage of data dictionary has not been initialized at all or
the initialization is incorrect.
13260
TOO MANY SUBSCRIBERS FOR THIS OPERATION
The source data contains too many subscribers for this
operation. There is not enough e.g. free RAM, disk or
database space available.
13261
OPTION FLEXIBLE MAIO MANAGEMENT IS NOT IN
USE IN BSC
The Flexible MAIO Management feature is not supported
in the BSC.
13262
TASK NOT ALLOWED AT THE MOMENT
The task is not allowed at the moment because the same
or some other task close to this one is under execution by
the service provider. Try again later.
13263
Issue: 30-0
REPORT FORMING SERVICE DOES NOT HAVE
RESOURCES TO FORM REPORT
DN987378
551
Error messages
General Error Messages of System
Report forming service cannot reserve the resources
needed in forming a report from RFMLIB library and
cannot form the report.
13264
OPERATION FAILED
An operation has failed in DXT. This error code can be
used in miscellaneous situations.
13265
CHANGE DELIVERY ALREADY INSTALLED IN THIS
PACKAGE
A change delivery has already been installed in this
package. Installing of new change deliveries is possible
only after removing already installed change deliveries
(WND). It is also possible to take a change delivery
package into use and install the desired change deliveries
in that.
13266
READING OF CFLIST FAILED
Error occured when reading CFLIST file.
13267
TRIED TO INSTALL SAME CHANGE DELIVERY MORE
THAN ONCE
The same change delivery has been attempted to install
more than once in one install command. The same change
delivery can only be installed once.
13268
CFLIST HAS UNKNOWN STRUCTURE
Error has occurred when trying to handle cflist (*.CFL) of
change delivery. Structure of CFLIST is unknown.
13269
CHANGE DELIVERY CONTAINS MAFILE WHEN
INSTALLING SEVERAL CHANGE DELIVERIES
There is an attempt to install several change deliveries
when at least one of them contains MAFILE. If a change
delivery contains MAFILE, it has to be installed separately.
A change delivery package has to be created before a
change delivery containing MAFILE can be installed. Also
after installing a change delivery containing MAFILE, a
change delivery package has to be created, if also the
other change deliveries are to be installed.
13270
NO CHANGE DELIVERIES TO BE REMOVED
This software package does not contain change deliveries
that could be removed. Change deliveries have not been
installed or they have already been removed.
13271
552
CHANGE DELIVERY IN WRONG STATE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Execution of operation is not allowed because change
deliveries are in wrong states.
13272
ERROR WHILE COMMUNICATING WITH SW2ADM
PROGRAM BLOCK
SW2ADM program block does not respond or the
message that is received contains an error code.
13273
ERROR WHILE COMMUNICATING WITH CPYMAN
PROGRAM BLOCK
CPYMAN program block does not respond or the message
that is received contains an error code.
13274
UNKNOWN RECORD TYPE
Error detected when trying to handle a file. The file
contains an unknown record type.
13275
FUNCTION IS NOT SUPPORTED
PCI hardware related functions return this value when
called in non-PCI hardware environment. Certain functions
return this value even in PCI hardware. These functions
are part of "standard" PCI service interface but have no
meaningful implementation in DX200 environment.
13276
INVALID PCI VENDOR ID
A PBMLIB service was called with an incorrect PCI vendor
id (i.e. value FFFFh).
13277
PCI DEVICE NOT FOUND
A specific PCI device was searched for but was not found.
It was not found because it does not exist or because it
has not been configured.
13278
INVALID PCI CONFIGURATION REGISTER NUMBER
Reading and writing to a PCI configuration register has
been attempted with a wrong register number. The allowed
range is 0-255 for bytes, 0,2,...,254 for words and
0,4,...,252 for dwords.
13279
INDEX IS OUT OF RANGE
The search for nth instance of a PCI device, PCI resource
or PCI interrupt line has failed because the specified
instance does not exist.
13280
INTERRUPT LINE DOES NOT EXIST
The device does not have an interrupt line.
13281
Issue: 30-0
RAN OUT OF I/O SPACE
DN987378
553
Error messages
General Error Messages of System
There is not enough free I/O space left in order to
successfully accomplish PCI bus configuration.
13282
OUT OF MEMORY SPACE
There is not enough free memory space left in order to
successfully accomplish PCI bus configuration.
13283
PCI DEVICE IS ALREADY IN THE DEVICE MAP
An attempt to add a PCI device in the device map has
failed because the specified device is already in the map.
13284
PCI MAP IS FULL
PCI device or resource map is full. A new device or
resource cannot be added.
13285
INVALID BAR REGISTER NUMBER
An incorrect PCI bar register number has been used.
13286
PBMLIB: INVALID COMPUTER ADDRESS
PBMLIB library routine has been called with invalid
computer address.
13287
COMMUNICATION FAILURE WITH PBMLIB
Communication between PBMLIB and PBLPRB program
blocks has failed.
13288
LINK FAILURE
TLC1-link or D-channel is in failure.
13289
TDSC FAILURE
TDSC in TETRA system is in failure state.
13290
OBJECT IS LOCKED FOR MML USE
The Q3 object is locked for MML use.
13291
ZERO IS NOT ALLOWED CELL RANGE FOR
EXTENDED CELL
The cell range is 0 (zero) although the cell has extendedrange TRXs. Give the cell range a new value (other than
zero) in the case that the cell has extended TRXs.
13292
THE SPECIFIED BASE IS NOT USED
The specified device does not use the specified base
address register.
13293
554
O&M LINK FAILURE. BCCH TRANSMISSION MAY BE
ACTIVE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Block the link of the broadcast channel of the cell.
13294
CARTRIDGE CODE NOT AVAILABLE
The code for cartridge type cannot be obtained by reading
I/O ports.
13295
UNKNOWN CHARGING MODIFICATION RESULT
The given charging modification result is unknown.
13296
ERROR IN WRITING INTO HIFILE FILE
Writing to the hifile file has failed.
13297
FILE NOT LOCKED BY USER
The file is not locked by user.
13298
LOCK TYPE IS ILLEGAL
User has given illegal lock type.
13299
NON-EXISTENT OBJECT
The object in question is undefined in the (applicationlevel) alarm system.
13300
DATA VERIFICATION ON TAPE HAS FAILED
Data verification has found erroneous data from tape
media.
13301
TAPE VERIFY ALREADY INITIALIZED
Tape verification initialization request is received even if it
has already been done.
13302
TAPE VERIFY NOT INITIALIZED
Tape verification is not initialized when verify data on tape
request is sent.
13303
ALARM DATABASE UPDATE FAILED DURING OBJECT
RESET
Updating of the alarm database failed after the successful
object reset.
13304
COPY PHASE ALREADY OVER
Copy phase is already over when copy interrupt request is
received.
13305
Issue: 30-0
ERROR IN READING HIFILE FILE
DN987378
555
Error messages
General Error Messages of System
Reading of HIFILE file has failed. Make needed corrections
to disk and try again. The operation may not be possible to
execute if there is no HIFILE file. The HIFILE file is located
in ASWDIR-directory of the software build which the
operation was directed to.
13306
V5 INTERFACE IS FULL
The V5 interface is full.
13307
CP UNIT WAS NOT RECOGNIZED
The CP unit could not be recognized according to
BOLERO global variables and reading DMX specific I/O
registers.
13308
INCORRECT CHANGE DELIVERY STATE IN HIFILE
The state information of change delivery is incorrect
according to the other information in HIFILE file. Updating
of data in HIFILE may have failed.
13309
DESTINATION PACKAGE NOT FOUND FROM HIFILE
Destination package information was not found from
HIFILE file. Updating of HIFILE may have failed.
13310
TIME PASSED
Time is passed.
13311
CHARGING MODIFICATION ANALYSIS CHAIN BROKEN
Chain of attributes of charging modification is broken.
13312
ILLEGAL PERCENTAGE VALUE FOR CHARGING
MODIFICATION
There is an illegal percentage value for charging
modification (too big).
13313
INDEX OF PLUG-IN UNIT IS TOO LOW
The index value is too high to add a new plug-in unit to
FNIM in DXT.
13314
THE SSI IS ALREADY IN USE BY A G4WIF
CONNECTION
The SSI in question is already reserved for identification of
a G4WIF connection.
13315
556
IF BB HOPPING BCCH TRX IS SUPER-TRX (FRT
OTHER THAN 0), ALL TRXS IN BTS MUST HAVE SAME
FRT
DN987378
Issue: 30-0
General Error Messages of System
Error messages
If the cell is baseband hopping on the underlay level and
its BCCH-TRX is a super-TRX (FRT other than 0), all the
other TRXs in the cell must also be super-TRXs and have
the same FRT as the BCCH-TRX.
13316
CHOSEN INTEGRITY CHECK CAN NOT BE DONE ON
THIS DATABASE
The integrity rule or the target (COMP_REL) chosen
cannot be checked on the given database. Availability of
some of the rules or target depends on the TDL compiler
version used in the pac of the database manager.
13317
GIVEN INTEGRITY RULE CAN NOT BE CHECKED ON
THIS DATABASE YET
The given rule cannot be checked on the chosen database
yet. The implementation of the rule depends on the version
of the TDL compiler used in the pac of the database
manager.
13318
POOL DOES NOT EXIST
The pool does not exist.
13319
RESTART STOPPED BY RECOVERY
Recovery has stopped unit restart.
13320
STARTUP OF THE FAMILY IS INCOMPLETE, ANOTHER
STARTUP MESSAGE IS REQUIRED
This error code indicates that the startup of the family is
not yet complete, and that another startup message is
required. A warmed TNSDL application, or actually its
translator-specific portion, inserts this error code to the
startup_ack_s message it sends as a response to the first
startup_s message received by the master process.
13321
REQUESTED SERVICE WAS NOT ACTIVATED
requested service cannot be activated due to the lack of
service parameters
13322
SERVICE IS IN ACTIVE STATE
Service parameters cannot be modified due to the
activation status of service
13323
GENERAL VIRTUAL SUBSCRIBER ALREADY EXISTS
A general virtual subscriber already exists.
13324
INCORRECT FILE EXTENSION
The given file extension is incorrect.
Issue: 30-0
DN987378
557
Error messages
General Error Messages of System
13325
GENERAL VIRTUAL SUBSCRIBER
General virtual subscriber.
13326
GENERAL VIRTUAL SUBSCRIBER DOES NOT EXIST
The general virtual subscriber does not exist.
13327
NUMBER MODIFIED DUE TO NUMBER PORTABILITY
SERVICE
This dx_cause is used when a number is modified by NP
service and it needs to be reanalyzed again at EOS or
EOS attribute analysis.
13328
UNTERMINATED CALL TO A PORTED NUMBER
This dx_cause is sent to SSO by CC to generate ANSI
ISUP REL cause 26 "Misrouted call to a ported number".
13329
THE GIVEN EXCHANGE NOT FOUND
the given exchange not found
13330
ILLEGAL PIU TYPE FROM IDENTIFY CIRCUIT OF A
PLUG-IN UNIT IN DMC COMPUTER
The PIU type in the DMC computer is not the same as
defined for it in the equipment database. The plug-in unit,
the computer cartridge or a CPU unit may be broken. The
error can also be caused by erroneous data about the PIU
in the equipment database or that the PIU is incorrectly
located in the cartridge (i.e. the PIU is not on the track
defined in equipment database).
13331
ILLEGAL TRACK NUMBER FROM IDENTIFY CIRCUIT
OF A PLUG-IN UNIT IN DMC COMPUTER
The track number in DMC computer is not the same as
defined for it in the equipment database. The plug-in unit,
the computer cartridge or the CPU unit may be broken.
The error can also be caused by erroneous data about the
PIU in the equipment database or that the PIU is
incorrectly located in the cartridge (i.e. the PIU is not on
the track defined in equipment database).
13332
FUSE ALARM FROM IDENTIFY CIRCUIT OF A PLUG-IN
UNIT IN DMC COMPUTER
There is a fuse alarm in the indentify circuit of a plug-in unit
in a DMC computer. The cause is most probably a blown
+5 V or - 5 V fuse in the PIU or all the interchangeable
bridge connections are unconnected. The error can also
be caused by a broken PIU, cartridge or CPU unit.
558
DN987378
Issue: 30-0
General Error Messages of System
13333
Error messages
UNKNOWN INTERCHANGEABILITY FROM IDENTIFY
CIRCUIT OF A PLUG-IN UNIT IN DMC COMPUTER
The software cannot identify the inter-changeability of the
PIU in DMC computer. Typically, the cause is erroneous
interchangeability bridge connections or the fact that the
software does not support interchangeability. The error can
also be caused by a broken PIU, cartridge or CPU unit.
13334
UNKNOWN VARIANT FROM IDENTIFY CIRCUIT OF A
PLUG-IN UNIT IN DMC COMPUTER
The software cannot identify the plug-in unit variant.
Typically, the cuase for the error is that the software does
not support that variant. The error can also be caused by a
broken PIU, carthrigde or CPU unit.
13335
THE CURSOR GIVEN TO THE DDILIB LIBRARY IS
INCORRECT
The cursor used for selecting data with the routines in the
DDILIB library is incorrect.
13336
DATA DICTIONARY OF THE DATABASE IS
INCONSISTENT
The data dictionary of the database cannot be used in this
inquiry because parts of data are missing or inconsistent.
13337
THIS PCM IS RESERVED FOR OTHER USE
If the PCM-TSL which includes Interexchange lines is
wanted to add PCM, which includes TBS data, this error
code is returned.
13338
THE OTHER MML SESSION IS IN OPERATION; TRY IT
AGAIN IN A FEW SECONDS
The other MML session is in operation. Try it again in a few
seconds.
13339
BITRATES OF COMBI LINKS DO NOT MATCH IN
AUTOCONFIGURED TRX CREATION
In the autoconfigured TRX creation the bitrates of BCF
O&M link and TRX Telecom link must be defined equal.
13340
COMBI LINK CAN BE CREATED ONLY TO FIRST TRX IN
AUTOCONFIGURED TRX CREATION
In the autoconfigured TRX creation the combi link can be
defined only for the first TRX.
13341
ULAPRB HAS NOT RECEIVED UPLOAD REQUEST
ULAPRB has not received request to start upload scenario
Issue: 30-0
DN987378
559
Error messages
General Error Messages of System
13342
OPTION ABIS AUTOCONFIGURATION NOT IN USE IN
BSC.
BSC support for autoconfiguration is an optional feature.
13343
THE TARGET DXT EXISTS ALREADY
The target DXT already exists in routing table.
13344
THE TARGET DXT IS UNKNOWN
The target DXT does not exist or is unknown to routing
table.
13345
NCGR IS NOT FOUND TO INDICATED DXT
NCGR value is not found from NTN database to indicated
DXT exchange.
13346
DESTINATION DXT DATA IS NOT FOUND FROM NTN
DATABASE
Indicated DXT information is not found from NTN
database.
13347
LOGICAL TSL NUMBER IS ALREADY DEFINED TO THIS
DESTINATION DXT
This logical TSL number is already used in this destination
DXT case.
13348
BSC IS FULL
Another BTS cannot be added to the BSC.
13349
BTS-BSC RELATION IS NOT DEFINED
The BTS is not under a BSC.
13350
CI ALREADY EXISTS IN LOCATION AREA
The given cell identity already exists in the location area.
13351
THERE ARE TOO MANY BSCS UNDER LOCATION
AREA
Too many BSCs exist in the location area.
13352
INVALID NEIGHBOUR DEFINITION
The ID of the neighbour is the same as the ID of the
object.
13353
MOBILE COUNTRY CODE OR MOBILE NETWORK
CODE IS NOT MODIFIED
The mobile country code or mobile network code is not
modified.
560
DN987378
Issue: 30-0
General Error Messages of System
13354
Error messages
THERE IS NO BTS IN MSC
The MSC does not contain a BTS.
13355
BSC DOES NOT EXIST
The given BSC is invalid.
13356
NO SUCH REFERENCE OBJECT
The reference object is invalid.
13357
THERE ARE TOO MANY BTSS WITH PERIODIC
INDICATION METHOD IN BSS
Too many BTSs in the BSS have periodic resource
indication method.
13358
NO RESPONSE FROM STATCO
The Statistical Control Program Block did not respond
within the specified time limit.
13359
FILE MISMATCH BETWEEN CMU AND STU
There is a file mismatch between BTSFIL in the CMU and
BSTRAF in the STU.
13360
NO RESPONSE FROM CM3PRO
CM3PRO did not respond within a specified time limit.
13361
NO RESPONSE FROM CRMPRB
CRMPRB did not respond within the specified time limit.
13362
BSC NAME OR NUMBER ALREADY EXISTS
The BSC already exists.
13363
BSC ADM. STATE CONFLICT
A conflict in the BSC administrative state exists between
RNEUPD and CRMPRB.
13364
BSC IS ALREADY RESTARTING
BSC is in reset mode.
13365
SPC UNKNOWN
Unknown signalling point code is given.
13366
SPC ALREADY USED BY ANOTHER BSC
SPC is already used by another BSC.
13367
Issue: 30-0
SSN AMOUNT EXCEEDED
DN987378
561
Error messages
General Error Messages of System
Too many SSNs.
13368
ROUTE UNKNOWN
The route for signalling point code is unknown.
13369
SIGNALLING LINK IS IN WRONG STATE
The signalling link is in wrong state.
13370
NAME OF BSSAP DOES NOT EXIST
BSSAP ID is invalid.
13371
BSSAP VERSION NAME ALREADY EXISTS
BSSAP version name already exists.
13372
MAXIMUM POOL AMOUNT EXCEEDED
Too large a pool amount.
13373
THERE IS NO BSC IN MSC
There is no BSC in MSC.
13374
LOCATION AREA ALREADY EXISTS IN PLMN
The location area already exists in the PLMN.
13375
PDP CONTEXT ALREADY EXISTS
The subscriber in hostel database already has the given
PDP context.
13376
PDP CONTEXT DOES NOT EXIST
PDP context is not found from the subscriber in hostel
database.
13377
PDP CONTEXT LIMIT EXCEEDED
The subscriber in hostel database can have max 7 pdp
contexts.
13378
INCONSISTENT GPRS DATA
- already PDP type + static PDP address pair - already
combination certain PDP type + no PDP address + certain
APN - PDP context with static PDP address contains
VPLMN allowed flag set yes (either a PDP address or
VPLMN allowed flag is tried to be modified).
13379
PRIMARY BASIC SERVICE IS NOT FOUND
The primary basic service is not found
13380
562
MNMPRO RESOURCE SHORTAGE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
MNMPRO process family has no own resources to make a
control channel termination.
13381
TERMINATION EXISTS
Control channel termination identified with interface VPI
and VCI already exists. Give a different control channel
identifier and try again.
13382
TERMINATION DOES NOT EXIST
An error when trying to remove a control channel
termination which does not exist. Give a termination that
exists and try again.
13383
TERMINATION PROVIDER NOT FOUND
The termination provider for the control channel
termination was not found. Check that the termination
providers exist and try again.
13384
TERMINATION PROVIDER NOT RESPONDING
The termination provider for the control channel
termination is not responding. Check that the termination
provider is working and try again.
13385
UNKNOWN CONTROL CHANNEL TYPE
Control channel type is unknown. Give a type that is
known by control channel management.
13386
ATM CONNECTION CONTROL NOT RESPONDING
ATM Connection Control services are not responding.
Check that these services are working and try again.
13387
MAXIMUM NUMBER OF INTEREXCHANGE SPEECH
LINES IS ALREADY DEFINED TO THIS DESTINATION
DXT
The maximum number of Interexchange Speech Lines is
already defined to indicated destination DXT.
13388
NOT ALLOWED IN SWT GENERAL GROUP
The operation is not allowed in SWT general group (trial
system).
13389
ALLOWED ONLY IN ACTIVE SYSTEM COMPUTER
The operation is allowed only in the active system
maintenance computer.
13390
Issue: 30-0
THE ADDRESS HAS BEEN ALREADY RESERVED
DN987378
563
Error messages
General Error Messages of System
An address has been already reserved with the given
address ID.
13391
ILLEGAL ADDRESS ID IS GIVEN
An illegal address ID has been given as a parameter.
13392
DYNAMIC ADDRESS ID NOT AVAILABLE
When reserving a dynamic physical address, a dynamic
address id is normally reserved, but no dynamic address
ID is available.
13393
PHYSICAL ADDRESS ID NOT AVAILABLE
A physical address which was to be reserved is not
available.
13394
INACCEPTABLE WIRED ADDRESS IS GIVEN
An inacceptable wired address was given as a parameter.
13395
GIVEN WIRED ADDRESS IS IN USE
The given wired address is in use.
13396
A DIFFERENT ADDRESS HAS BEEN RESERVED
A different address than the given has been reserved with
the given address ID.
13397
NOT ACCEPTED BY POST OFFICE
The operation is not accepted by the post office.
13398
GIVEN ADDRESS ID AND ADDRESS DO NOT MATCH
The given address ID and physical address do not match.
13399
PHYSICAL ADDRESS NOT KNOWN
No physical address is connected to the given address ID.
13400
ADDRESS ID NOT KNOWN
No address ID is connected to the given physical address.
13401
PHYSICAL ADDRESS MANAGEMENT ERROR
A physical address management error has been found.
13402
CHANGE NOTES INSTALLED TO SYSTEM WITHOUT
MANAGEMENT
Several Software Management operations do not work
properly anymore if Change Note Management feature is
not utilized. In this situation, there is a ******** string in the
cd ID field in the MAFILE record 0 (this string it not visible
564
DN987378
Issue: 30-0
General Error Messages of System
Error messages
in all WQ output commands). Change Deliveries should be
installed by using CN Management (Installation is done by
using WN, WQ and WS command groups). If in case in the
software build there are already Change Notes which are
installed without utilizing CN Management, it is no longer
possible to install Change Deliveries by using CN
management. This is because the build is no longer in the
control of Software Management.
13403
V3 SUPERVISION IS NOT ACTIVE
V3 supervision feature is possible with this ET, but it is not
activated.
13404
V3 LOOPBACK IS NOT POSSIBLE
V3 loopback, either in LT or in NT1, is not possible.
13405
DMX EXCEPTION
A process family has made a DMX exception.
13406
FREQUENCY BAND ALREADY EXISTS
The added frequency band already exists in the database.
13407
CARRIER PAIR ALREADY EXISTS
The carrier pair has already been defined into the
database.
13408
DUPLEX INDEX ALREADY EXISTS
Duplex space with given index has already been defined
into the database.
13409
DUPLEX SPACING ALREADY EXISTS
The duplex spacing has already been defined into the
database.
13410
LOCATION AREA ALREADY EXISTS
The location area object has already been defined into the
database.
13411
BASE STATION RELATED TO ANOTHER CELL
The base station belongs to another cell and cannot be
used in another one.
13412
CARRIER RELATED TO A TTRX
The carrier pair is being used by a TTRX and cannot be
disposed.
13413
Issue: 30-0
FALLBACK CARRIER RELATED TO TTRX
DN987378
565
Error messages
General Error Messages of System
The fallback carrier pair is related to a TTRX and cannot
thus be disposed.
13414
FALLBACK DUPLEX SPACE DOES NOT EXIST
The duplex spacing defined to be used in fallback mode
has not been defined into the database.
13415
NEIGHBOUR CELL DOES NOT EXIST
The neighbour cell object has not been defined into
database.
13416
LOCATION AREA OF NEIGHBOUR CELL NOT FOUND
The location area of the neighbour cell has not been
defined into database.
13417
RELATIONSHIP HAS ALREADY BEEN DEFINED
The relationship has already been defined into database.
13418
RELATIONSHIP HAS NOT BEEN DEFINED
Relationship has not been defined into database.
13419
OBJECT HAS WRONG ORGANIZATION BLOCK
Object has wrong organization block.
13420
OBJECT ALREADY A MEMBER
The object is already a member of the entity it is being
added to (e.g. a group or a service handle).
13421
OBJECT NOT A MEMBER
The object is not a member of the entity in question (e.g. a
group or a service handle).
13422
OBJECT ALREADY IN AREA
The object already belongs to the area definition of the
entity (e.g. a group).
13423
OBJECT NOT IN AREA
The object does not belong to the area definition of the
entity (e.g. a group).
13424
SGSN NAME ALREADY EXISTS
If record already exists with the same name when creating
an SGSN record to SGFILE.
13425
566
REQUESTED TASK IDENTIFICATIONS NOT FOUND
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The application has inquired copy task identifications, but
no identifications were returned. If the task identification of
active copy tasks were requested, there were no copy
tasks in progress. If the task identifications of logged copy
tasks were requested, the copy log was empty.
13426
NO SUCH COPY TASK LOG
The application has requested a copy log or logs, but no
information was returned. The copy log was empty or none
of the stored logs matched the given filtering criteria.
13427
THE COUNTRY IS UNKNOWN
The country does not exist or is unknown to R2 parameter
table.
13428
BCF DELETION DENIED DUE TO BCF-CONTROLLED
TRANSMISSION EQUIPMENT
The BCF shall not have any other than TRE-1
transmission equipment under its control when it is
deleted. Existing transmission equipment may not be in
use when the BCF is deleted. Remove other than TRE-1
transmission equipment from BCF control and check
states of existing equipment.
13429
POINT-TO-POINT CONFIGURATION NONEXISTENT
The point-to-point configuration supplementary service is
nonexistent (it has not been defined).
13430
ADDING OF TRANSMISSION EQUIPMENT FAILED
Adding of transmission equipment failed
13431
FUNCTIONAL ENTITY DOES NOT EXIST
Functional entity does not exist.
13432
HALF RATE CHANNELS ARE NOT ALLOWED WHEN
MODIFYING HALF RATE SUPPORT OFF
When the TRXs Half Rate Support (HRS) parameter is
switched off there should not exist any half rate channels.
13433
E-GSM900 FREQUENCIES ARE NOT ALLOWED TO
2ND GENERATION BTS
Nokia 2nd generation bts does not support E-GSM900
frequencies.
13434
INADEQUATE TRANCEIVER CONFIGURATION
The requested state change of TTRX of Tetra Base Station
was rejected due to missing transceiver parameters.
Issue: 30-0
DN987378
567
Error messages
General Error Messages of System
13435
COMMAND PARTLY SUCCESSFUL: SGSN NOT
UPDATED
The data cannot be transferred to SGSN correctly. The
MAP interface rejects the given operation. However, the
data has been stored in the HLR database.
13436
COMMAND PARTLY SUCCESSFUL: NODES NOT
UPDATED
The data cannot be transferred to VLR and SGSN
correctly. The MAP interface rejects the given operation.
However, the data has been stored in the HLR database.
13437
SUPERVISION BLOCK COUNT FOR SELECTIVE
STATISTIC COLLECTION IS EXCEEDED
Supervision block count exceeded in selective statistic
collection object definition. Check given supervision block
count.
13438
USE OF COMBINED D-CHANNELS NOT POSSIBLE IN
THIS BCF
The site type of BCF does not allow the use of combined
D-channels. A Combined D-channel contains both O&Msignaling and telecom signaling in the same physical
timeslot (PCM-TSL).
13439
NOT FOUND BY TDLRUN
TDLRUN cannot find the object (e.g. a record, a tuple, a
collection object, etc) being searched. This code is
intended to be used internally by TDLRUN.
13440
LIST IS TOO LONG
A general negative acknowledgement to DWS when a list
sent by DWS is too long to be decoded
13441
FAMILY RESTART ORDERED BY RECOVERY
The recovery system has internally ordered a restart of a
process family.
13442
FAMILY RESTARTED DUE SYNCH FAILURE
The family has been restarted due to synchronisation
failure.
13443
UPDATING OF CURRENT TIME FAILED BECAUSE OF
O&M LINK FAULT
The current time cannot be updated for BTS because the
O&M link is down.
13444
568
IO_TEXT NOT FOUND IN RADIO NETWORK DATABASE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
input / output text was not found in the radio network
database
13445
OPTION ADVANCED MULTILAYER HANDLING IS NOT
IN USE IN BSC.
Feature Advanced Multilayer Handling is optional.
13446
NO SUCH FILE SET ON TAPE
The given file set does not exist on tape.
13447
FILE SET ALREADY EXISTS ON TAPE
The name of the file set is not unique on used tape.
13448
TAPE FILE FORMAT OUT OF ORDER
The tape file format on used media is out of order.
13450
THERE ARE TOO MANY BCFS IN RADIO NETWORK
CONFIGURATION DATABASE
The maximum number of BCFs is already created to this
Radio Network configuration
13451
THERE ARE TOO MANY BTSS IN RADIO NETWORK
CONFIGURATION DATABASE
The maximum number of BTSs is already created to this
Radio Network configuration
13452
THE GIVEN STATISTICAL MEASUREMENT TYPE HAS
AN ANILLEGAL VALUE
The given statistical measurement type has an illegal
value.
13453
SELECTIVE STATISTICAL MEASUREMENT IS ACTIVE
WHEN OPERATION IS GIVEN
The statistical measurement is active, so the operation is
ignored. Stop the measurement.
13454
PARAMETERS OUT OF RANGE
Parameters are out of their valid ranges in message.
13455
TP IS FREE TP
Termination Point (TP) is free termination point.
13456
TP IS RESERVED TP
Termination Point (TP) is reserved termination point.
13457
Issue: 30-0
TP IS RESERVED MC TP
DN987378
569
Error messages
General Error Messages of System
Termination Point (TP) is reserved multicast (MC)
termination point.
13458
OPTION DIRECT ACCESS TO DESIRED LAYER/BAND
IS NOT IN USE IN BSC
The purpose of the DADL/B feature is to direct the traffic in
call setup phase from the SDCCH of macro cell / GSM900
cell to the TCH of micro cell / GSM1800 cell whenever
possible.
13459
UNKNOWN ABIS AUTOCONFIGURATION POOL
REQUEST TYPE
The Abis autoconfiguration pool request type in unknown.
13460
UNKNOWN OR MISSING PARAMETER IN ABIS
AUTOCONFIGURATION POOL REQUEST
There is unknown or missing parameter in Abis
autoconfiguration pool request.
13461
ERROR IN READING ABIS AUTOCONFIGURATION
POOL FILE (ACQFIL)
Reading the Abis autoconfiguration pool file (ACQFIL)
fails.
13462
ERROR IN WRITING ABIS AUTOCONFIGURATION
POOL FILE (ACQFIL)
There is an error in writing to Abis autconfiguration pool file
(ACQFIL).
13463
THE ABIS AUTOCONFIGURATION POOL FILE (ACQFIL)
IS FULL
There is no room in Abis autoconfiguration pool file
(ACQFIL).
13464
ERROR IN UPDATING ABIS AUTOCONFIGURATION
POOL FILE (ACQFIL) TO HARD DISKS OF BSC
There is an error in updating Abis autoconfiguration pool
file to BSC disks.
13465
POOL DELETION DENIED BECAUSE OF ONGOING
ABIS ALLOCATION PROCEDURE
Abis autoconfiguration pool deletion denied because of
ongoing abis allocation procedure.
13466
NO CREATED POOLS FOUND FROM POOL FILE
(ACQFIL)
No created pools found from the Abis autoconfiguration
pool file (ACQFIL).
570
DN987378
Issue: 30-0
General Error Messages of System
13467
Error messages
NO POOLS MATCHING TO GIVEN PARAMETERS
FOUND FROM POOL FILE (ACQFIL)
No pools matching to given parameters found from the
Abis autoconfiguration pool file (ACQFIL).
13468
PCM AND/OR TSL(S) ALREADY IN USE IN ANOTHER
POOL
Given PCM and/or TSL(s) already in use in another Abis
autoconfiguration pool.
13469
RESPONSE MESSAGE FROM PXADMI MISSING
PXADMI is not responding to service request.
13470
RESPONSE MESSAGE FROM PUBDAT MISSING
PUBDAT is not responding to service request.
13471
ACKNOWLEDGE MESSAGE FROM BTTEST MISSING
BTTEST is not sending the acknowledge message to
service request.
13472
ALL TEST REPORT MESSAGES FROM BTTEST
MISSING
All TRX specific test report messages from BTTEST are
missing.
13473
REQUEST DENIED DUE TO UNFINISHED ABIS
AUTOCONFIGURATION PROCEDURE
Request is denied due to unfinished Abis autoconfiguration
procedure.
13474
ACMANA IS BUSY
Abis autoconfiguration manager program block is busy.
13475
D-CHANNEL CREATION FAILED
Creation of the D-channel has failed.
13476
D-CHANNEL DATA INQUIRY FAILED
D-channel data inquiry from PXADMI has failed.
13477
D-CHANNEL MODIFY FAILED
D-channel modifying has failed.
13478
D-CHANNEL ACTIVATION/DEACTIVATION FAILED
Activation/deactivation of the D-channel has failed.
13479
Issue: 30-0
D-CHANNEL REMOVE FAILED
DN987378
571
Error messages
General Error Messages of System
Removing of the D-channel has failed.
13480
RESOLVING OF THE SIGNALLING UNIT FOR THE
ACCESS CHANNEL FAILED
Resolving of the signalling unit for the Abis
autoconfiguration pool access channel has failed.
13481
ABIS AUTOCONFIGURATION POOL CIRCUIT
RESERVATION FAILED
Abis autoconfiguration pool circuit reservation has failed.
13482
ABIS AUTOCONFIGURATION POOL CIRCUIT
RELEASING FAILED
Abis autoconfiguration pool circuit releasing has failed.
13483
SOME OF THE RESOURCES IN BTS NOT TESTED
DURING BTS AUTOCOMMISSIONING
Some of the resources in BTS has not tested during BTS
commission test.
13484
BTS COMMISSIONING TEST FAILED
Commissioning test for the BTS has failed.
13485
NO TRXS INCLUDED IN COMMISSION TEST REQUEST
There are no TRXs included in commission test request.
13486
UNKNOWN ABIS MESSAGE IDENTIFIER FROM BTS
ACMANA has received an unknown Abis message
identifier from BTS.
13487
COMMAND ELEMENT (PARAMETER) MISSING FROM
THE ABIS MESSAGE
Command element (parameter) of the Abis message
received by ACMANA is missing.
13488
ERROR IN INTERNAL FUNCTIONALITY OF THE
ACMANA
An error has occured in internal functionality of the
ACMANA.
13489
ABIS AUTOCONFIGURATION POOL FULL
There is no more room for allocations in Abis
autoconfiguration pool.
13490
572
MISSING OR WRONG PARAMETER IN ABIS CIRCUIT
AUTOCONFIGURATION REQUEST FROM BTS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
There is missing or wrong parameter in Abis circuit
autoconfiguration request from BTS.
13491
ACKNOWLEDGEMENT FROM BTS TO ABIS CIRCUIT
ALLOCATION NOTIFICATION IS MISSING
The acknowledgement from BTS to Abis circuit allocation
notification is missing.
13492
WRONG ACKNOWLEDGEMENT FROM BTS TO ABIS
CIRCUIT ALLOCATION NOTIFICATION
The acknowledgement from BTS to Abis circuit allocation
notification is wrong.
13493
ABIS AUTOCONFIGURATION PROCEDURE
INTERRUPTED
Abis autoconfiguration procedure has been interrupted.
13494
ERROR IN ALLOCATING SPEECH CHANNELS FOR A
TRX
Speech channel allocation for the TRX has failed.
13495
BTS RESTART INDICATION MISSING
BTS restart indication message is missing.
13496
BCF IS NOT WAITING FOR ABIS
AUTOCONFIGURATION
The BCF is not waiting for the Abis autoconfiguration.
13497
TRX IS NOT WAITING FOR ABIS
AUTOCONFIGURATION
The TRX is not waiting for the Abis autoconfiguration.
13498
O&M LINK AND TRX LINK BIT RATE MISMATCH IN LINK
COMBINING
There is a O&M link and TRX link bit rate mismatch in link
combining.
13499
THE BIT RATE OF THE TRX LINK DOES NOT
CORRESPOND WITH THE SUBTIMESLOTS RESERVED
FOR OPTIMN
The bit rate of the TRX link does not correspond with the
subtimeslots reserved for optimized Abis allocation.
13500
TEXT IS ILLEGAL
Text contains either no character or it has illegal
characters.
Issue: 30-0
DN987378
573
Error messages
General Error Messages of System
13501
BCF IS WAITING ABIS AUTOCONFIGURATION.
BCF, which is created to be autoconfigured, is waiting abis
autoconfiguration in BL-WAC operative state.
13502
OBJECTS LOCKED UNDER BCF WAITING ABIS
AUTOCONFIGURATION.
Under BCF, which is waiting abis autoconfiguration, is
locked BTS or TRX.
13503
INPUTS ARE NOT VALID FOR THE SITE TYPE
The type of BCF (defined by BCF parameter BTS site
type) does not support inputs (e.g. external alarms)
13504
GIVEN TASK IDENTIFICATION IS NOT UNIQUE
The given task identification is not unique. For example the
backup copy task is rejected, if the copy log already
contains information of a task of identical identification.
13505
G4WIF ALREADY EXISTS IN NTN DATABASE
The G4WIF is already found in NTN database.
13506
G4WIF IS NOT FOUND IN NTN DATABASE
The requested G4WIF is not found in NTN database.
13507
ADDING NOT ALLOWED BECAUSE G4WIF ALREADY
DEFINED TO EXTERNAL LINE
The external line cannot be added to the circuit group,
because G4WIF is already defined for the external line.
13508
G4WIF MONITORING IS NOT ALLOWED BECAUSE
G4WIF IS CONNECTED TO GROUP
The G4WIF monitoring is not allowed, because G4WIF is
already connected to some group.
13509
SELECTION LEVEL IS NOT ALLOWED
Selection level is not allowed.
13510
REMOVING DXT IS NOT ALLOWED BEFORE ALL
INTEREXCHANGE SPEECH LINES ARE REMOVED
Removing DXT is not allowed before all interexchange
speech lines are removed.
13511
OPTION FLEXIBLE COUNTER SELECTION SET IS NOT
IN USE IN BSC
Flexible counter selection set feature is not supported in
the BSC.
574
DN987378
Issue: 30-0
General Error Messages of System
13512
Error messages
GROUP ALREADY EXISTS IN NTN DATABASE
Group already exists in NTN database.
13513
COMMUNICATION ERROR WITH TETRA ENCRYPTION
MODULE
An error in the communication with a Tetra encryption
module has occured.
13514
MEMORY OF TETRA ENCRYPTION MODULE FAULTY
The memory of Tetra encryption module is faulty.
13515
TETRA ENCRYPTION MODULE COUNTER TEST
ERROR
Tetra encryption module counter test is incorrect.
13516
TETRA ENCRYPTION MODULE SERIAL PORT TEST
ERROR
Tetra encryption module serial port test is incorrect.
13517
TETRA ENCRYPTION MODULE RANDOM NUMBER
GENERATOR FAULTY
The random number generator of Tetra encryption module
is faulty.
13518
ZONE CODE ALREADY EXISTS
Zone Code already exists in Zone Code Index table
(ZCITBL) of radio network file.
13519
ZONE CODE NAME ALREADY EXISTS
Zone Code Name already exists in Zone Code Name table
(ZCNTBL) of radionetwork file.
13520
NO MORE FREE SIGNALLING CAPACITY WITH
CURRENT HW OR SW CONFIGURATION
There is no more free signalling capacity to create any new
signalling links. Capacity of AS7 plug-in-units has been run
out.
13521
SPECIAL ROUTE ATTACHED
The given special route is attached to a component.
13522
THE GSMP FUNCTIONALITY IS ENABLED
The GSMP functionality is enabled. The GSMP control
channel cannot be deleted when the GSMP functionality is
enabled.
13523
Issue: 30-0
THE GSMP CONTROL CHANNEL ALREADY EXISTS
DN987378
575
Error messages
General Error Messages of System
The GSMP control channel has been defined. Only one
GSMP control channel can exist at a time.
13524
THE GSMP CONTROL CHANNEL DOES NOT EXIST
The GSMP control channel has not been defined. The
GSMP functionality cannot be activated before the GSMP
control channel is defined.
13525
ATM CROSS CONNECTION SERVICES ARE NOT
RESPONDING
ATM cross connection services are not responding to a
service request. Check that the service provider is alive
and try again.
13526
TESTING OF THE REQUESTED OBJECT IS NOT
ALLOWED
The BTTEST rejects the testing of the unallowed test
object.
13527
TIME SLOT USED TO SIGNALING
Testing is not allowed because timeslot is used to
signalling.
13528
TEST INTERRUPTION IS NOT ALLOWED
Test interruption request is received in state where
interruption is not allowed.
13529
ABIS LOOP TEST LOOP CONNECTION FAILED
Loop connection to the GSWB failed.
13530
TESTING OF CONTROL CHANNEL NOT ALLOWED
Abis loop test is requested to the radio timeslot which is
dedicated to be as control channel.
13531
EXTENDED FREQUENCIES USED WITH STM
EQUIPMENT
Extended frequencies are not allowed with STM test
equipment.
13532
SYSTEM KEY OF TETRA ENCRYPTION MODULE IS
FAULTY
The system key of Tetra Encryption module is faulty.
13533
PDP CONTEXT LIMIT EXCEEDED IN HOSTEL
DATABASE
The subscriber in hostel database can have maximum 7
pdp contexts.
576
DN987378
Issue: 30-0
General Error Messages of System
13534
Error messages
DISTINCTIVE RINGING NOT ALLOWED
A notice related to subscriber handling - inquiry, creation,
or deletion. The notice means that the subscriber has the
distinctive ringing facility on, and the subscriber handling
command is not allowed on subscribers with distinctive
ringing facility.
13535
TRANSMISSION EQUIPMENT DELETION DENIED
Transmission equipment in question can not be deleted.
13536
UNABLE TO WRITE DATA ON VDS DEVICE DUE THE
STATE OF DATA FILES.
VDS device driver is unable to write data on the hard disk
file due the state of current data file is FULL and
overwriting is disabled. If skipping of FULL files is enabled,
VDS device driver has not found any files in
TRANSFERRED state.
13537
THE STATUS OF VDS DATA FILE IS NOT CHANGED
DUE THE REQUESTED STATE TRANSITION IS ILLEGAL
The status of VDS data file is not changed due the
requested status transition is illegal.
13538
VDS DEVICE DRIVER IS UNABLE TO STORE DATA
DUEINITIALIZATION OF DATA FILE HAS FAILED
VDS device driver is unable to store data due initialization
of data file has failed.
13539
VDS DEVICE DRIVER IS UNABLE TO STORE DATA ON
HARD DISKS
VDS device driver is unable to store data on hard disks.
13540
VDS DEVICE DRIVER IS UNABLE TO HANDLE THE
REQUESTED TASK DUE THE STATE OF COMPUTER
UNIT
A request is send to VDS device driver in computer unit
which state does not allow requested task to be
completed.
13541
CHECKSUM POLLING ALREADY ON
The checksum polling is already going on.
13542
EQUIPMENT COLLECTION ALREADY ON
The equipment collection is already going on.
13543
Issue: 30-0
NEGATIVE ACKNOWLEDGEMENT FROM BASE
STATION
DN987378
577
Error messages
General Error Messages of System
The BTS has replied with a negative acknowledgement
message to the POOL_SIZE_REPORT or
AC_BSC_CIRCUITS_ALLOCATED message sent by
ACMANA Program Block during Abis Autoconfiguration
procedure.
13544
ABIS AUTOCONFIGURATION PROCEDURE
INTERRUPTED BY BTS
The BTS has interrupted the Abis Autoconfiguration
procedure by sendingthe AC_INTERRUPTED message to
ACMANA Program Block.
13545
CANNOT COMBINE OMUSIG AND TRXSIG LINKS
The combining of OMUSIG and TRXSIG during Abis
Autoconfiguration cannot be completed. Either the
OMUSIG or the TRXSIG for the TRX 1 has already been
allocated or requires no allocation for some other reason.
13546
PROCESSOR OF TETRA ENCRYPTION MODULE
FAULTY
The processor of TETRA Encryption module is faulty.
13547
WRONG MESSAGE FROM BTS DURING ABIS
AUTOCONFIGURATION
The BTS has replied with an Abis message that does not
belong to the current Abis Autoconfiguration phase.
13548
UNKNOWN LINK BIT RATE IN ABIS
AUTOCONFIGURATION
The link bit rate (OMUSIG or TRXSIG) read from the BSC
Radio Network Database or from the DCHSET File is
unknown to ACMANA Program Block.
13549
WRONG BSC C-NUMBER FROM BTS DURING ABIS
AUTOCONFIGURATION
The BSC C-number sent by BTS in the
AC_CIRCUIT_REQ message differs from the own BSC Cnumber.
13550
NO RESPONSE FROM GUPDAT TO THE BCF
RESERVE OR RELEASE REQUEST
No response from GUPDAT to the BCF reserve/release
request sent by ACMANA program Block during Abis
Autoconfiguration.
13551
578
GSMP SERVICES SERVICE PROVIDER NOT
RESPONDING
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The service provider for GSMP Services does not respond
to service request.
13552
THE SPECIFIED ATM INTERFACE HAS NOT GOT A
GSMP PORT DEFINED
The interface specified in the request does not have a
GSMP port defined.
13553
CIRCUIT GROUP DEFINITION IS NOT FOUND FROM
NTN DATABASE
Circuit group is not found from database.
13554
DXT ALREADY EXISTS IN NTN DATABASE
dxt already exists in ntn database
13555
BOLERO DATA AREA NOT FOUND
BOSLIB did not find BOLERO data area or did not
recognize it (e.g. wrong version).
13556
DATA DID NOT FIT IN BOLERO DATA AREA
The area reserved for data is smaller than the data you
tried to save.
13557
DATA WAS NOT FOUND IN BOLERO
The given data was not found in BOLERO data area.
13558
BOSLIB DID NOT RECOGNIZE THE DATA
BOSLIB did not recognize the data id as BOLERO data.
13559
BOLERO DATA IS WRITE PROTECTED
The data can not be written into BOLERO data area,
because the area of the data is write protected.
13560
BOLERO DATA INDEX IS TOO LARGE
There are not so much data records in BOLERO data area
as the index asks for.
13561
BLSLIB NOT INITIALIZED
BLSLIB has not been initialized (with the library
initialization function).
13562
DATA NOT FOUND IN BLSLIB AREA
There is no record in BLSLIB data area that would contain
the data.
13563
Issue: 30-0
DATA IS TOO LARGE IN BLSLIB AREA
DN987378
579
Error messages
General Error Messages of System
Data is so large in BLSLIB data area that it cannot be read
into the given area.
13564
BLSLIB AREA IS FULL
The data cannot be saved in the BLSLIB data area,
because it does not fit in the free area at the moment.
13565
DATA SCOPE NOT RECOGNIZED
BLSLIB did not recognize the scope of the data.
13566
DATA LIFETIME NOT RECOGNIZED
BLSLIB did not recognize the lifetime of the data.
13567
INDEX BIGGER THAN THE AMOUNT OF RECORDS
The index of the data is bigger than the amount of records
in BLSLIB data area.
13568
V5 INTERFACE IS NOT ACTIVATED
The V5 interface is created but not activated.
13569
MATCHING V5 INTERFACE NOT FOUND
Inquired V5 interface was not found.
13570
DATABASE IS WAITING FOR INITIALIZATION MESSAGE
The database management system is started but has not
received an initialization message.
13571
REMOVING OF DXT IS NOT ALLOWED, BEFORE ALL
G4WIFS ARE REMOVED
Removing of dxts is not allowed, before all g4wifs are
removed.
13572
REMOVING OF DXT IS NOT ALLOWED, BEFORE ALL
CIRCUIT GROUPS ARE REMOVED
Removing of dxt is not allowed, before all circuit groups
are removed.
13573
REMOVING OF DXT IS NOT ALLOWED, BEFORE ALL
DXT_SERVICES ARE REMOVED
Removing of dxt is not allowed, before all dxt_services are
removed.
13574
VCLTP DOES NOT EXIST
The given identifier is not assigned to any existing VCLtp.
13575
580
VCI ALREADY EXISTS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The given identifier is already in use under the specified
VCLtp.
13576
VCLTP EXISTS
The operation could not be performed because there are
VCLtps under the VPLtp.
13577
VC DATA INCONSISTENT IN THE SYSTEM
An error occurred during the command execution.
Corrective actions could not restore the consistency of the
databases.
13578
GSMP SWITCH INFO NOT DEFINED
The switch information for GSMP does not exist in the
database.
13579
NO ACKNOWLEDGEMENT FOR HOT DATA TRANSFER
Timer which supervises TPPIPE (Transport Pipe Provider)
interface has expired.
13580
INVALID TPI LEVEL
Termination point level information is not suitable for
requested operation.
13581
STATE CHANGE NOT ALLOWED
The requested state change is not allowed. For example
the administrative state from locked -> shutting down state
is not allowed transition.
13582
REMOTE SYSTEM IS NOT READY TO RECEIVE HOT
DATA
Remote system can not receive immediately sent hot
records.
13583
GIVEN SERVICE CATEGORY IS NOT ALLOWED
The given service category is not defined, or service
category of VPCtp and VCLtp mismatch.
13584
CONNECTION DOES NOT EXIST
The specified connection does not exist.
13585
TP IS CONNECTED
The specified termination point is connected.
13586
TP DOES NOT SPECIFY A PTM ROOT
The given termination point does not specify a root
termination point of a point-to-multipoint connection.
Issue: 30-0
DN987378
581
Error messages
General Error Messages of System
13587
UNABLE TO DELETE LAST BRANCH SEPARATELY
The last branch of a point-to-multipoint connection may not
be deleted with the delete branch command. The delete
connection command must be used.
13588
CONNECTION DATA INCONSISTENT IN THE SYSTEM
An error occurred during the command execution.
Corrective actions could not restore the consistency of the
databases.
13589
TERMINATION MANAGEMENT SERVICE NOT
RESPONDING
Termination management service is not responding to a
service request in a given time. The service could be down
or busy. Try to request the service again.
13590
G4WIF DATA IS NOT FOUND FROM NTN DATABASE
G4wif data is not found from ntn database.
13592
VPI ALREADY EXISTS
The given VP identifier is already in use under the
specified interface.
13593
VPLTP EXISTS
The operation could not be performed because there are
VPLtps under the interface.
13594
TP IS NOT UNLOCKED
The operation could not be performed because the state of
the termination point is not unlocked.
13595
TP DOES NOT SPECIFY A PTM BRANCH
The specified operation can only performed on a
termination point related to a ptm branch.
13596
TP SPECIFIES A PTM BRANCH
The operation could not be performed because the given
termination point specifies a ptm branch.
13597
VPLTP SERVICE LEVEL IS VPC
The specified VPLtp has been configured for VP
connections.
13598
VPLTP SERVICE LEVEL IS VCC
The specified VPLtp has been configured for VC
connections.
582
DN987378
Issue: 30-0
General Error Messages of System
13599
Error messages
VPLTP SERVICE TYPE ALLOWS NO PVC
The specified VPLtp has been configured for switched
(SVC) connections.
13600
VPLTP SERVICE TYPE ALLOWS NO SVC
The specified VPLtp has been configured for permanent
(PVC) connections.
13601
TERMINATION POINT IS NOT IN LOCKED STATE
The specified operation requires the termination point to be
in locked administrative state.
13602
VPI IS INSIDE GSMP PORT
The specified VPLtp is inside a GSMP port and the
requested operation can not be performed. Specify a
different VPLtp or use GSMP handling commands to
handle this VPLtp.
13603
VP DATA INCONSISTENT IN THE SYSTEM
An error occured during the command execution.
Corrective actions could not restore the consistency of the
database.
13604
CONNECTION ERROR
An error has occured with connection in AAPSEB service
block.
13605
TRANSFER ERROR
An error has occured with transfer in AAPSEB service
block.
13606
USED SERVICES NOT KNOWN
Used services are not known and thus the service request
cannot be served. Try again later.
13607
ATM LINE ALREADY IN USE
The given line on specified plug-in unit is already in use by
another ATM interface.
13608
ATM INTERFACE DOES NOT EXIST
The given identifier is not assigned to any existing ATM
interface.
13609
ATM INTERFACE IS NOT LOCKED
The operation could not be performed because the ATM
interface is not locked.
Issue: 30-0
DN987378
583
Error messages
General Error Messages of System
13610
ATM INTERFACE DATA INCONSISTENT IN THE
SYSTEM
An error occurred during the command execution.
Corrective actions could not restore the consistency of the
databases.
13611
ATM INTERFACE HAS A GSMP PORT DEFINED
The operation could not be performed cause the ATM
interface has a GSMP port assigned to it.
13612
ACCESS PROFILE EXISTS
The specified ATM interface already has a profile.
13613
ACCESS PROFILE DOES NOT EXIST
The specified ATM interface does not have a profile.
13614
CURRENTLY MORE VP CONNECTIONS DEFINED
The modification attempted to reduce the number of VP
connections allowed on the ATM interface. Currently there
are more VP connections than the new value would allow.
13615
CURRENTLY MORE VC CONNECTIONS DEFINED
The modification attempted to reduce the number of VC
connections allowed. Currently there are more VC
connections than the new value would allow. Increase the
parameter "maximum number of VCCs" or give the
command again later.
13616
CURRENT CONNECTIONS USE MORE VCI BITS
The modification attempted to reduce the number of bits
used in the VCI. Currently there are connections whose
VCI requires more bits than the new value would allow.
Increase the parameter "maximum number of VCI bits" or
give the command again later.
13617
ACCESS PROFILE DATA INCONSISTENT IN THE
SYSTEM
An error occurred during the command execution.
Corrective actions could not restore the consistency of the
databases.
13618
ATM INTERFACE ID ALREADY EXISTS
The given identifier is already assigned to another ATM
interface. Repeat the command with a suitable value or let
the system select a free one.
13619
584
QOS AND SERVICE CATEGORY MISMATCH
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The given QoS class for termination point or connection
does not match the given service category.
13620
TRAFFIC PARAMETERS AND SERVICE CATETORY
MISMATCH
The given traffic parameters for termination point or
connection do not match the service category.
13621
THE VPLTP DOES NOT EXIST
The given VP identifier is not assigned to any existing
VPLtp.
13622
FATAL ERROR
The error code informs, that unrecoverable error has
occured.
13623
VPLTP HAS AN ACCESS PROFILE
The specified VPLtp already has an access profile.
13624
VPLTP HAS NO ACCESS PROFILE
The specified VPLtp does not have an access profile.
13625
VPLTP DOES NOT EXIST
The given VP identifier is not assigned to any existing
VPLtp.
13626
OBJECT ALREADY IN USE
error code to report when the requested object is already
in use.
13627
MANY G4WIF OBJECT MEMBERS OF A GROUP
Error Code to report when the Group has already the
maximum no of g4wifobjects as members.
13628
SIGNALLING LINK ID ALREADY IN USE
Signalling link-id is already in use.
13629
SIG_SERVICE_ERROR_EC
Error in creating a new hand for signalling link
13630
SIGNALLING TYPE NOT AVAILABLE
Signalling type is unknown.
13631
UNKNOWN SIGNALLING LINK ID
Signalling link_id is unknown.
Issue: 30-0
DN987378
585
Error messages
General Error Messages of System
13632
SYSTEM KEY FILE OF TETRA ENCRYPTION MODULE
IS FAULTY
The system key file of Tetra Encryption module is faulty.
13633
SAR STATUS QUEUE EMPTY
There are no RSM Status Queue entries ready to return or
no available SEG Status Queue entry to release.
13634
CHECKING OF WS SESSION FAILED
This error code is used to indicate that there was an error
getting session information from database.
13635
WS HAS NO SESSION
This error code is used to indicate that there is no users
logged on to WS.
13636
CHECKING OF WS USER RIGHTS FAILED
This error code is used to indicate that there was an error
in checking WS user rights.
13637
NO ACKNOWLEDGEMENT RECEIVED FROM DXT
This error code is used to indicate that DXT has not
answered to a request.
13638
SENDING MESSAGE IN SEGMENTS FAILED
This error code is used to indicate that there was an error
when sending a segmented message.
13639
RECEIVING MESSAGE IN SEGMENTS FAILED
This error code is used to indicate that there was an error
when receiving a segmented message.
13640
MESSAGE SEGMENT HAS A WRONG TYPE
This error code is used to indicate that the received
message segment has not the correct type. This means
that when the data is expected, an acknowledgement to a
segment is received or other way around.
13641
MESSAGE SEGMENT ALREADY RECEIVED
This error code is used to indicate that the received
message segment is already received before.
13642
MESSAGE SEGMENTS IN WRONG ORDER
This error code is used to indicate that message segments
are coming in wrong order.
586
DN987378
Issue: 30-0
General Error Messages of System
13643
Error messages
ACKNOWLEDGEMENT TO WRONG MESSAGE
SEGMENT
This error code is used to indicate that the received
acknowledgement to a segment is not the expected one.
13644
WRITING DATA TO A BUFFER FAILED
This error code is used to indicate that there was an error
when writing data to a buffer.
13645
WS USER HAS NO RIGHTS TO DELETE RADIO
SUBSCRIBER
This error code is used in WCRPRB, when ws users right
for the delete-command is checked.
13646
WS USER HAS NO RIGHTS TO CREATE RADIO
SUBSCRIBER
This error code is used in WCRPRB, when ws users right
for the create-command is checked.
13647
ISSI OF A RADIO SUBSCRIBER IS NOT IN ALLOWED
ISSI RANGE OF WS USER
This error code is used in WCRPRB, when ws users right
for the create-command is checked.
13648
WS USER HAS NO RIGHTS TO MODIFY ORG. BLOCK
ID OF RADIO SUBSCRIBER
This error code is used in WCRPRB, when ws users right
for the modify-command is checked. This is used when the
WS user has already the right to modify the WS user. But if
he wants to modify the org. block id of the WS user, he
must have the right to create or delete WS user both to the
old and new org. block.
13649
WS USER HAS NO RIGHTS TO MODIFY RADIO
SUBSCRIBER AT ALL
This error code is used in WCRPRB, when ws users right
for the modify-command is checked.
13650
OPEN-LEVEL STACK OVERFLOW/UNDERFLOW
Stack which stores open levels has overflowed or
underflowed. Reason for underflow is probably popoperation without push. Possible causes for overflow are
too small amount of nesting levels, or too many pushoperations / level.
13651
CURRENT LEVEL IS UNDEFINED
Used operation requires TLV-code containing at least one
level.
Issue: 30-0
DN987378
587
Error messages
General Error Messages of System
13652
TAG SHOULD BE READ INSTEAD
Tag must be read before using this operator.
13653
VALUE SHOULD BE READ INSTEAD
Value must be read or skipped before using this operator.
13654
EMPTY CONSTRUCTED ELEMENT
Every constructed element must contain at least one
subelement.
13655
TAG CLASS WAS UNKNOWN
Only application-class tags can be decoded. This error is
probably caused by invalid TLV-code.
13656
TLV-CODE IN NOT VALID
TLV-code is not valid. Probably this is caused by conflicting
length in TLV-code.
13657
TAG FIELD IS TOO LONG
Tag does not fit to space reserved for it. This may indicate
invalid TLV-code.
13658
LENGTH FIELD IS TOO LONG
Length of value does not fit to space reserved for it. This
may indicate invalid TLV-code.
13659
EMPTY-VALUE STACK OVERFLOW/UNDERFLOW
Stack which stores locations of empty values has
overflowed or underflowed. Reason for underflow is
probably attempt to fill empty value without adding it first.
Possible cause for overflow is too small maximum amount
for empty values.
13660
DIFFERING LENGTHS WHILE FILLING VALUE
Lengths given for "add_next_empty" and "fill_empty_val"
are differing.
13661
TLV-CODE CONTAINS EMPTY VALUES
All empty values must be filled before finishing encoding.
13662
PARAMETER WITH UNIT IS TOO BIG
The given parameter, a combination of numerical value
and unit, results in a value which is too big.
13663
588
DXT NOT DEFINED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The given DXT has not been defined in this exchange of
the network.
13664
CIS NODE DEFINITION IS NOT FOUND FROM NTN
DATABASE
Cis node definition is not found from ntn database.
13665
CIS NODE ALREADY EXISTS IN NTN DATABASE
Cis node is already found in ntn database
13666
ERROR CODE FOR BACK GROUND GROUP
Main level error code reported when DWS tries to add
members to a background group, when the group
downloading is not used.
13667
ILLEGAL OPERATION FOR THE MS TYPE
Error code reported in the ec list when the operation is not
allowed for the requested MS.
13668
CONNECTION GROUP HAS CIRCUIT GROUPS.
Connection group has circuit groups.
13669
END OF CURRENT LEVEL IS REACHED
Current level is read completely. End of some upper levels
can be reached simultaneously.
13670
INVALID HANDOVER REASON
the handover reason is wrong or not possible.
13671
DXT WITH GIVEN SHORT DXT IDENTITY VALUE
ALREADY EXISTS IN NTN DATABASE
Dxt with given short dxt identity already exists in ntn
database.
13672
DXT WITH GIVEN LOCATION IDENTITY VALUE
ALREADY EXISTS IN NTN DATABASE
Dxt with given location identity value already exists in ntn
database
13673
DXT WITH GIVEN OWN-FLAG VALUE ALREADY EXISTS
IN NTN DATABASE
Dxt with given own-flag value already exists in ntn
database
13674
RIGHT TO ACTIVATE CALLING NUMBER DELIVERY
NOT SET
The right to activate calling number delivery is not set.
Issue: 30-0
DN987378
589
Error messages
General Error Messages of System
13675
CALLING NUMBER DELIVERY SET
Calling number delivery is set.
13676
TYPE OF ADVICE OF CHARGE NOT SET
Type of advice of charge (IAO) is not set.
13677
TYPE OF ADVICE OF CHARGE SET
Type of advice of charge (AOD, AOE, AOS, ACD, ACE or
ACS) is set.
13678
CALL WAITING NOT SET
Call waiting (CW) is not set.
13679
RIGHT TO NOTIFY CALLING SUBSCRIBER THAT CALL
WAITING HAS BEGUN SET
Right to notify calling subscriber that call waiting has
begun (CWN) isset.
13680
CALL DIVERSION ON HOOK NOT SET
Call diversion on hook (CTH) is not set.
13681
FAST TRANSFER SET
Fast transfer to ringing (CTF) or Fast transfer to busy
(CTB) is set.
13682
THREE PARTY SERVICE SET
Three party service (IPTY) is set.
13683
THREE PARTY AND HOLD FOR ENQUIRY SET
Three party and hold for enquiry (PS) are set.
13684
CALL HOLD FACILITY NOT SET
Call hold facility (HOLD) is not set.
13685
RIGHT TO USE COMPLETION OF CALLS TO BUSY
SUBSCRIBERS SET
Right to use completion of calls to busy subscribers (CCS)
is set.
13686
RIGHT TO ACTIVATE BARRING OF COMPLETION OF
CALLS TO BUSY SUBSCRIBERS SET
Right to activate barring of completion of calls to busy
subscribers (CCR) is set.
13687
590
RIGHT TO USE NUMBER REPETITION IN COMPLETION
OF CALLS TO BUSY SUBSCRIBERS (PRE-CCBS) SET
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Right to use number repetition in completion of calls to
busy subscribers (pre-CCBS) is set.
13688
FIXED DESTINATION CALL IS ACTIVE SET
Fixed destination call is active (FD) is set.
13689
DIRECT DIALLING-IN NOT SET
Direct dialling-in (DDI) is not set.
13690
COMMON PART LENGTH OF MSN NUMBER SET
Common part length of MSN number (DCP) is set.
13691
CALL TRACING IS ON
Call tracing (CT, CTT/MI) is on.
13692
ISDN GROUP CALL NUMBER
ISDN group call number.
13693
CAC CHECKING ACTIVATED NOT SET
CAC checking activated (CA) is not set.
13694
INTERNATIONAL CAC CHECKING ACTIVATED NOT
SET
International CAC checking activated (CAI) is not set.
13695
SPECIFIED ATM INTERFACE DOES NOT EXIST
The specified ATM interface is not defined for the given
plug-in unit.
13696
SSCF SERVICE ERROR
Error in SSCF service provider.
13697
SSCOP SERVICE ERROR
Error in SSCOP service provider.
13698
PARSE ERROR
An error occured while parsing the input parameters of the
command.
13699
BCF IS RESERVED TO SOME OTHER TEST
Test execution is not possible because the BCF resource
is reserved to some other test.
13700
TESTING IS NOT REQUESTED TO THIS TEST OBJECT
This test object do not belong to test objects whose testing
is requested.
Issue: 30-0
DN987378
591
Error messages
General Error Messages of System
13701
SOME OF THE RADIO TIME SLOTS ARE NOT TESTED
SUCCESSFULLY
Radio time slots assosiated to the tested TRX are not
tested successfully
13702
ZONE CODE NOT UPDATED
The update of the zone code data failed.
13703
HARDWARE INITIALIZATION FAILED
This is a general error code for hardware initialization
failure.
13704
2M LINK DOES NOT EXIST
2M link does not exist.
13705
V5 INTERFACE IS ALREADY SHUT DOWN
V5 interface is already shut down
13706
TABLE ERROR IN AAPSEB
AAPSEB SW has found an error in its internal table.
13707
RNGLIB IS OUT OF RAND NUMBERS
RNGLIB is out of random numbers, pseudo random
numbers used instead.
13708
THE PXADMI DOES NOT ANSWER TO THE DCHANNEL CREATION OR DELETION
The pxadmi does not response to the creation or deletion
message of D-channel.
13709
D-CHANNEL CREATION DOES NOT SUCCEED IN
AUTOCONFIGURED TRX/BCF CREATION
In the creation of autoconfigured BCF/TRX the creation of
d-channel does not succeeded.
13710
THE COMBINED LINK DOES NOT EXIST IN THE
CREATION OF AUTOCONFIGURED TRX
The combined d-channel link does not exists when the
autoconfigured trx is created.
13711
FAMILY RESTARTED
Family restarted manually.
13712
592
RNW ALARM SYSTEM INTERNAL BUFFER OVERFLOW
DN987378
Issue: 30-0
General Error Messages of System
Error messages
All RNW alarms haven t been able update to
alarmhistoryfile and internal alarmhistory buffer has filled.
This causes that some alarms are missing from
alarmhistory.
13713
TRANSMISSION EQUIPMENT HAS WRONG STATE
Transmission equipment has wrong state for the requested
operation.
13714
THE REQUESTED WS USER IS NOT CURRENTLY
LOGGED
The requested ws user is not currently logged.
13715
TOO MANY FREQUENCIES IN BTS
There are more frequencies in BTS than can be in cell
allocation.
13716
PASSWORD CONTAINS ILLEGAL CHARACTER(S)
Password contains at least one illegal character.
13717
TBS IS NOT DEFINED IN NTN DATABASE.
Tbs is not defined in ntn database.
13718
FUN UNIT IS NOT FOUND IN NTN DATABASE
Fun unit is not found in ntn database.
13719
FUN UNIT ALREADY EXISTS IN NTN DATABASE
Fun unit already exists in ntn database.
13720
PCM-TSL NUMBER IS TOO HIGH
PCM-TSL number is too high.
13721
SUBSCRIBER HAS NO INTERFACES TO HWEQUIPMENT
Subscriber has no interfaces to hw-equipment.
13722
REMOVING OF DXT IS NOT ALLOWED,BEFORE ALL
TRCS ARE REMOVED
Removing of dxt is not allowed before all trc:s are
removed.
13723
CGR IS ALREADY DEFINED TO THIS DXT
Circuit group is already defined to this dxt.
13724
CGR ALREADY EXISTS IN NTN DATABASE
Circuit group already exists in ntn database.
Issue: 30-0
DN987378
593
Error messages
General Error Messages of System
13725
CGR OF THIS DXT IS NOT FOUND
Circuit group is not connected to this dxt.
13726
PCM-TSL IS NOT FOUND IN NTN DATABASE
PCM-TSL is not found in ntn database.
13727
RELATION TO PCM-TSL IS NOT FOUND
Relation to PCM-TSL is not found
13728
CONNECTION GROUP ALREADY EXISTS IN NTN
DATABASE
Connection group already exists in ntn database.
13729
GATEWAY IS ALREADY FOUND IN NTN DATABASE
Gateway is already found in ntn database
13730
CONNECTION GROUP IS NOT FOUND IN NTN
DATABASE
Connection Group is not found in ntn database
13731
PHYSICAL ADDRESS MANAGEMENT IS INITIATED
Physical address management has already been initiated,
so initiation calls will not be accepted any more.
13732
D-CHANNEL DELETION DOES NOT SUCCEED IN
AUTOCONFIGURED TRX/BCF CREATION/DELETION
In the creation/deletion of autoconfigured TRX/BCF, the
deletion of D-channel does not succeed.
13733
ATM CROSS CONNECTION PATH SERVICE NOT
RESPONDING
ATM cross connection path service provider is not
responding.
13734
LINE ALREADY EXISTS IN THIS CIRCUIT GROUP
Line already exists in this circuit group.
13735
FUNCTIONAL UNIT FOUND TO THIS REMOTE OBJECT
Functional unit found to this remote object
13736
LINE IS NOT IN THIS CIRCUIT GROUP
Line is not in this circuit group
13737
EXTERNAL LINE DOES NOT HAVE CIRCUIT GROUP
PARAMETERS
External line does not have circuit group parameters
594
DN987378
Issue: 30-0
General Error Messages of System
13738
Error messages
DXT SERVICE OBJECT MISSING FROM CONNECTION
GROUP
Dxt service object missing from connection group
13739
EXTERNAL LINE IS NOT FOUND FOR CIRCUIT GROUP
External line is not found for circuit group
13740
SOFTWARE LINE INDEX ALREADY FOUND
Software line index already found
13741
CONFLICT WITH FNIM AND EXTERNAL LINE PCMNUMBERS
Conflict with fnim and external line pcm-numbers
13742
CONFLICT IN EXTERNAL LINE SSI
Conflict in external line ssi
13743
TSL IS MISSING FROM EXTERNAL LINE
Tsl is missing from external line
13744
THE D-CHANNEL DATA INQUIRY DOES NOT SUCCEED
The D-channel data inquiry does not succeed.
13745
CREATING COMBINED LINK IS POSSIBLE
Creating a combined link is possible.
13746
DELETING COMBINED O&M LINK NOT ALLOWED
Deleting a combined O&M link not allowed.
13747
VCC WAS ALREADY RESERVED
VCC was already reserved to another process.
13748
VCC IS RESERVED TO ANOTHER PROCESS FAMILY
VCC cannot be released because it is reserved to another
process family.
13749
VCC WAS FREE
VCC was not released because it was free.
13750
RESERVED TO ANOTHER PROCESS FAMILY
VCC is reserved to another process family.
13751
VCC IS FREE
Supervised VCC is free.
Issue: 30-0
DN987378
595
Error messages
General Error Messages of System
13752
LINK SUPERVISION ERROR
Link supervision error.
13753
PACKET DISCARD VALUES CONFLICT. EPD- AND PPDENABLE SHOULD HAVE THE SAME VALUES.
The hardware does not support different values for Early
Packet Discard (EPD) and Partial Packet Discard (PPD).
They have to be either both enabled or both disabled.
13754
RECOVERY IS BUSY DUE TO SYM UNIT RESTART
RECOVERY IS BUSY AT THE MOMENT DUE TO SYM
UNIT RESTART.
13755
RACK OR CABINET TYPE ALREADY EXISTS
The rack or cabinet already exists and cannot be created
in equipment database.
13756
CABINET HMS INDEX ALREADY EXISTS
The HMS index of cabinet already exists in equipment
database, and thus this HMS index cannot be used.
13757
RACK OR CABINET DOES NOT EXIST
The rack or cabinet does not exist in equipment database,
and thus it cannot be deleted or a subrack cannot be
created for it.
13758
RACK OR CABINET HAS SUBRACKS
The rack or cabinet has subracks in equipment database
and thus it cannot be deleted.
13759
INCORRECT RACK OR CABINET TYPE
The given rack or cabinet type is incorrect and thus it
cannot be created in equipment database.
13760
SUBRACK ALREADY EXISTS
The subrack already exists in equipment database and
thus it cannot be created again.
13761
SUBRACK HMS INDEX ALREADY EXISTS
The subrack HMS index already exists in equipment
database, and thus the given index cannot be used.
13762
SUBRACK DOES NOT EXIST
The subrack does not exist in equipment database and
thus it cannot be deleted.
13763
596
SUBRACK HAS PIUS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The subrack has plug-in units in equipment database and
thus it cannot be deleted.
13764
INCORRECT SUBRACK TYPE
The subrack type is incorrect and thus it cannot be created
in equipment database.
13765
PLUG-IN UNIT ALREADY EXISTS
The plug-in unit already exists in equipment database and
thus it cannot be created again.
13766
PLUG-IN UNIT DOES NOT EXIST
The plug-in unit does not exist in equipment database and
thus it cannot be e.g. deleted or connected.
13767
PLUG-IN UNIT HAS CONNECTED PORTS
The plug-in unit has connected ports in equipment
database and thus it cannot be deleted.
13768
PLUG-IN UNIT HAS NO FREE RESOURCES
The plug-in unit has no free resources in equipment
database and thus no new resources can be reserved from
it.
13769
PLUG-IN UNIT HAS NO RESERVED RESOURCES
The plug-in unit has no reserved resources in equipment
database and thus resources cannot be freed from it.
13770
PLUG-IN UNIT IS ATTACHED TO UNIT
The plug-in unit is attached to a unit and thus cannot be
deleted from equipment database.
13771
PLUG-IN UNIT HAS RESOURCES IN USE
The plug-in unit has reserved recourses in equipment
database, and thus it cannot be deleted.
13772
PLUG-IN UNIT IS ALREADY ATTACHED TO UNIT
The plug-in unit is already attached to a unit and thus it
cannot be attached again.
13773
PLUG-IN UNIT IS NOT ATTACHED TO UNIT
The plug-in unit is not attached to a unit and thus cannot
be deattached.
13774
INCORRECT PLUG-IN UNIT TYPE
The plug-in unit type is incorrect. Thus it cannot be created
or deleted from equipment database.
Issue: 30-0
DN987378
597
Error messages
General Error Messages of System
13775
UNIT ALREADY EXISTS
The unit already exists in equipment database and thus
cannot be created.
13776
UNIT DOES NOT EXIST
The unit does not exist in equipment database, and thus it
cannot be deleted.
13777
INCORRECT UNIT TYPE
The unit type is incorrect or unit group index is invalid, and
thus it cannot be created or deleted from equipment
database.
13778
UNIT ATTACHMENT DOES NOT EXIST
The unit attachment does not exist in equipment database,
and thus it cannot be deattached.
13779
PORT OF PLUG-IN UNIT DOES NOT EXIST
The port of plug-in unit does not exists in equipment
database, and thus it cannot be connected.
13780
CONNECTION BETWEEN PORTS ALREADY EXISTS
The connection between ports of plug-in unit already
exists, and thus the ports cannot be connected.
13781
CONNECTION BETWEEN PORTS DOES NOT EXIST
The connection between ports of plug-in units does not
exist, and thus the ports cannot be disconnected.
13782
ILLEGAL PORT CONNECTION
The connection between the ports of plug-in units is not
allowed.
13783
PORT CONNECTION DATA DOES NOT EXIST
The connection data between two ports does not exist, and
thus it cannot be read from equipment database.
13784
INTERNAL ERROR IN EQCPRO PROCESS
An internal error has happened in EQCPRO process.
13785
FAULTY OPERATION USED
A faulty operation has been used in communication
between EQCPRO and other processes.
13786
598
ILLEGAL DB PARAMETER VALUE USED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
An illegal parameter has been used in communication
between equipment database and some other process.
13787
ILLEGAL SEARCH KEY COMBINATION USED
An illegal search key combination has been used when
retrieving data from equipment database.
13788
ROUTING TABLE CANNOT BE OPENED
Routing table cannot be opened
13789
INTERRUPTING IS NOT ALLOWED
Interrupting the active test is not allowed. Try again later.
13790
FILE DELETION NOT ALLOWED
File deletion is not allowed because destination build is
created in SOMAFI file.
13791
MAFILE CORRESPONDING TO CDID NOT FOUND
The MAFILE corresponding to change delivery
identification is not found.
13792
DELETING OF SCMANA DIRECTORY IS NOT ALLOWED
Deleting of SCMANA directory is not allowed.
13793
NOT A CENTREX SERVICE NUMBER
Centrex is not a centrex service number.
13794
MAXIMUM NUMBER OF TRUNCATED NUMBERS
EXCEEDED
Maximum number of truncated numbers allowed in the
KIDATA database exceeded.
13795
THERE EXISTS A SUBSCRIBER IN THE TRUNCATED
NUMBERS VALUE RANGE
There exists a subscriber in KIDATA database that belongs
to the value range of the truncated number being added.
13796
SUBSCRIBER BELONGS TO THE VALUE RANGE OF A
TRUNCATED NUMBER
Subscriber being added belongs to the value range of an
existing truncated number in KIDATA database.
13797
AT PRESENT ANOTHER SESSION IS ACTIVE
At present another session is active, so current service has
to be repeated later
13798
Issue: 30-0
PARAMETER TARGET_ID IS INVALID
DN987378
599
Error messages
General Error Messages of System
Parameter target_id is invalid ( points to a DXT which does
not exist )
13799
PARAMETER PRI_ROUTE IS INVALID
Parameter pri_route is invalid ( points to a DXT which does
not exist )
13800
PARAMETER SEC_ROUTE IS INVALID
Parameter sec_route is invalid ( points to a DXT which
does not exist )
13801
WRITING INTO ROUTING TABLE WAS
UNSUCCESSFUL
Writing into routing table was unsuccessful
13802
ROUTING TABLE IS UPDATED/READ BUT CAN NOT BE
CLOSED
Routing table is updated/read but can not be closed
13803
PRIMARY DISTANCE ( GIVEN IN PRI_DIST ) IS OUT OF
RANGE
Primary distance ( given in pri_dist ) is out of range
13804
SECONDARY DISTANCE ( GIVEN IN SEC_DIST ) IS
OUT OF RANGE
Secondary distance ( given in sec_dist ) is out of range
13805
RECORD IN ROUTING TABLE CAN NOT BE DELETED
Record in routing table can not be deleted
13806
RECORD IN ROUTING TABLE CAN NOT BE READ
Record in routing table can not be read
13807
DATABASE READING WAS NOT SUCCESSFUL
Database reading was NOT successful ( during reading all
DXT IDs which are in network )
13808
DBP DB NOT FOUND
The database record is not found from DBPARA.
13809
DBP ERRONEOUS RECORD LENGTH
The record length of DBPARA is erroneous.
13810
RESPONSE TO A THRESHOLD QUERY
This is a response to a threshold query made to AIMPRB.
600
DN987378
Issue: 30-0
General Error Messages of System
13811
Error messages
REQUESTED THRESHOLD IS NOT SET
Cannot answer to query because the requested threshold
is not set.
13812
SUCCESSFULLY UPDATED
The threshold values are successfully updated.
13813
THRESHOLD IS NOT SET
The threshold specified in this message is not set.
13814
VPLTP OR VCLTP ALLOCATION IS REJECTED
BECAUSE OF LACK OF UNALLOCATED CELL BUFFER
CAPACITY
VPLtp or VCLtp allocation is rejected because of the lack
of unallocated cell buffer capacity
13815
ALLOCATION IS REJECTED BECAUSE OF LACK OF
BANDWIDTH OR TOO STRICT DELAY REQUIREMENTS
Allocation is rejected because of the lack of unallocated
bandwidth or too strict delay requirements.
13816
REQUESTED SERVICE CATEGORY FOR VCLTP IS NOT
SUPPORTED IN THE VPCTP (FOR VCCS)
Requested service category for VCLtp is not supported in
the VPCtp (for VCCs)
13817
NUMBER OF VPC AND/OR VCC CONNECTIONS
WITHIN INTERFACE IS EXCEEDING THE SET LIMITS
VPC or VCC connection rejected because of the number
of VPC and/or VCC connections within interface is
exceeding the set limits.
13818
THE NUMBER OF VCC CONNECTIONS WITHIN VPLTP
IS EXCEEDING THE SET LIMITS
VCC connection rejected because of the number of VCC
connections within VPLtp is exceeding the set limits.
13819
CAC HAS FOUND WRONG PARAMETERS IN THE
INCOMING SERVICE REQUEST
CAC has found wrong parameter(s) in the incoming
service request. Error code is used as a general indication
of the wrong parameters in the received message.
13820
GENERAL HIGH LEVEL CAC ERROR CODE
A general high level CAC error code.
13821
Issue: 30-0
GENERAL LOW LEVEL CAC ERROR CODE
DN987378
601
Error messages
General Error Messages of System
A general low level CAC error code.
13822
INCONSISTENT PARAMETERS
Inconsistent parameters are detected.
13823
FNIM OBJECT ALREADY FOUND IN NTN DATABASE
The FNIM object is already found in NTN database.
13824
HTTP SESSION HAS BEEN EXPIRED
HTTP session has been expired.
13825
THE INPUT IS NOT HANDLED IN THIS SYM UNIT
Recovery does not handle the input in this active/passive
SYM unit.
13826
THERE ARE NO ONGOING TESTS
There is no test active in the BSC.
13827
THE INPUT TIMESTAMP IS OLDER THAN THAT
STORED IN DATABASE
This is used in updates of replicated information. If the
timestamp attached to incoming data is older than that
stored with the data in the database, the data in the
database is not updated, otherwise the incoming data
replaces the older data and the timestamp is updated too.
13828
ATTEMPTING TO DELETE RUNNING BUILD
Destination build cannot be deleted, because it is running
in some or in all computer units.
13829
ATTEMPT TO DELETE BUILD ONLY FROM OMU
It is not allowed to delete build from OMU if it still exists in
some other disk units SOMAFI
13830
IT SEEMS THAT DIRECTORY IS NOT BUILD
DIRECTORY (THERE IS NOT LFILES SUBDIRECTORY)
This is warning notification: there is not LFILES
subdirectory under given directory.
13831
IT IS NOT ALLOWED TO DELETE BUILD THAT HAS
STATUS BU
It is not allowed to delete build that has status BU. Check if
build is correct one or change statuses.
13832
IT IS NOT ALLOWED TO DELETE DEFAULT BUILD
It is not allowed to delete default build. Check if build is
correct or change default build information.
602
DN987378
Issue: 30-0
General Error Messages of System
13833
Error messages
ACTIVE INFO OF BUILD IN DIFFERENT SOMAFI FILES
CONFLICTS
Active information of build between different SOMAFI files
in disk units is conflicting.
13834
ONLY ACTIVE BUILD IN DIRECTORY CANNOT BE
DELETED
Only active build in directory cannot be deleted, whereas
both builds can be deleted at the same time (if this is
otherwise allowed).
13835
DIRECTORY BASED DELETING IS NOT ALLOWED IN
THESE CONDITIONS
Directory based deleting is not allowed. Try some other
parameter combination.
13836
MAFILE BASED DELETING IS NOT ALLOWED IN
THESE CONDITIONS
MAFILE based deleting is not allowed in these conditions.
It is possible that a suitable MAFILE is not available or the
er combination and the d configuration do not match. Try
some other parameter combination.
13837
BUILD CONFIGURATION IN NETWORK ELEMENT IS
NOT LEGAL
Build configuration in network element (between different
disk units) is not legal. Deleting of builds is not safe in
these conditions.
13838
GIVEN UNIT IS NOT UNDER SOFTWARE
CONFIGURATION MANAGEMENT
Given unit is not under SW configuration management.
13839
DISK UPDATING IS IN PROGRESS
When RXEPRB program block receives the message
save_scd_to_disk_s with save_mode_t_normal_c, the
user is immediately acknowledged with this status.
13840
TOO MANY SUBSCRIBERS IN ORGANIZATION BLOCK
There are too many subscribers in the organization block.
13842
AC ACCESS CHANNEL CANT BE USED AS TELECOM
OR O&M LINK
AC (AutoConfiguration) Access Channel can not be used
as telecom or O&Mlink
Issue: 30-0
DN987378
603
Error messages
General Error Messages of System
13843
CIS NODE CANNOT BE DELETED FROM NTN
DATABASE BECAUSE CIS CLIENT SESSIONS ARE IN
PROGRESS
CIS node cannot be deleted from NTN database. There
are CIS client sessions in progress.
13844
VPCTP DOESNT HAVE ENOUGH CAPACITY FOR
VCLTPS
VPCtp does not have enough capacity for VCLtps.
13845
THE MAXIMUM NUMBER OF ACTIVE HTTP SESSIONS
HAS BEEN EXCEEDED
The maximum number of active HTTP sessions has been
exceeded, new sessions cannot be established.
13846
NO RESPONSE FROM SERVICE PROVIDER
No acknowledgement was received from the service
provider within timeout limit.
13847
CIS NODE ID IS OUT OF RANGE
The allowed range for CIS Node ID is said in the
Numbering Feature Description. This ID is SSI from the
system number area.
13848
GIVEN COMPUTER UNIT DIFFERS FROM PREVIOUSLY
DEFINED UNITS
Previously defined functional units are connected to
different computer unit. You can check the unit example
with command DSF:TTRX, tbs nb;
13849
CNYFAM DOES NOT ANSWER
The CNYFAM family in the destination unit does not
answer.
13850
STARTING OF A FAMILY FAILED IN A PREPROCESSOR
Starting of a process family failed in a preprocessor unit.
13851
FAMILY SUPERVISION ERROR IN A PREPROCESSOR
Supervision of a process family failed in a preprocessor
unit.
13852
INCALL AND/OR CRN IS LINKED TO THE CENTREX
GROUP
An Incall number and/or Call Return number is linked to
the centrex group.
13853
604
LOGICAL MULTICAST NOT SUPPORTED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Logical multicast is not supported in the system.
13854
THE POINTED CONNECTION IS NOT ON VP-LEVEL
An attempt has been made to point to a vc-level
connection when the used routine is intended to be used
with vp-level connections
13855
THE POINTED CONNECTION IS NOT ON VC-LEVEL
An attempt has been made to point to a VP-level
connection when the used routine is intended to be used
with VC-level connections.
13856
NO SWITCH INFO EXISTS
There is no stored switch info in the system
13857
PERMANENT INDEX OUT OF THE RANGE RESERVED
FOR THE SPECIFIC OBJECT TYPE
The permanent index value used to point to an object was
not within the range reserved for the object type
13858
LOCAL INDEX OUT OF THE RANGE RESERVED FOR
THE SPECIFIC OBJECT TYPE
The local index value used to point to an object was not
within the range reserved for the object type
13860
INVALID TETRA AUTHENTICATION ALGORITHM
VERSION
The given TETRA authentication algorithm version is
invalid.
13861
INVALID VALUE RANGE DEFINITION
The range definition is invalid, for example minimum value
may exceed maximum.
13862
THE TERMINATION POINTS TO BE CONNECTED ARE
THE ONE AND SAME TERMINATION POINT
The identifiers of the two termination points to be
connected point to the same record in the database. The
connection can not be created.
13863
THE UNIT STATE OF TDSC IS NOT WO-EX
the state of the TDSC functional unit is not WO-EX.
13864
FORBIDDEN MMI USER PASSWORD
The given password is not allowed to be used as MMI
password.
Issue: 30-0
DN987378
605
Error messages
General Error Messages of System
13865
COMPUTER RESTART TIME-OUT
Computer restart has not completed in predefined time.
13866
SPECIFIED ORG IS SPECIAL ORG
specified org is special org
13867
THERE IS NO MASTER DXT IN THE SUBNET
There is no master dxt in the subnet.
13868
SUBNET NOT FOUND
no subnet associated with given dxt or with given dynamic
address
13869
NO IP SERVICE
ip service not allowed
13870
NO DYNAMIC ADDRESS PAIRS FOR AN
ORGANIZATION
an organization does not have address pool where saves
ip dynamic address pairs
13871
NUMBER OF ADDRESS PAIRS REACHES MAXIMUM,
CANNOT ADD ANY
the number of address pairs reaches the max, cannot add
any more.
13872
CANNOT FIND GIVEN STATIC OR DYNAMIC IP
ADDRESS
cannot find given static address or dynamic address pairs
which should be modified
13873
CANNOT ADD MORE DXTS, DXT LIMIT EXCEEDED
the number of DXT in a subnet exceeded, cannot add DXT
to it.
13874
MEMBER DXT STILL EXISTS
there is at least one member DXT in the subnet, cannot
delete master DXT.
13875
INVALID IP ADDRESS
invalid ip address
13876
THE CONVERSION RECORD IS NOT IN THE CHAIN
THE CONVERSION RECORD IS NOT IN THE CHAIN
13877
606
CNEFIL CORRUPTED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
CNEFIL CORRUPTED
13878
PIGPRB IS NOT READY TO PROVIDE THE
REQUESTED SERVICE
This error is received when services are requested when
PIGPRB is not ready to serve. One example of this kind of
situation is when service request arrives when PIGPRB
initialization is still continuing after startup, in this case
repeating the request later may help.
13879
THE PROVIDER OF THE SERVICE REQUESTED IS
NOT READY TO SERVE THE REQUEST
The service provider is not ready to perform the requested
service. Try again later.
13918
SYSTEM CALL NOT AVAILABLE
Attempt to invoke a system call that is not available within
this configuration.
13919
INVALID MESSAGE IDENTIFIER
The message identifier parameter is not a valid message
address, or the corresponding message has already been
consumed.
13920
LINK FAILURE DURING REMOTE IPC
A remote communication protocol failure has been
detected during remote IPC.
13921
PORT IN USE
Attempt to migrate a port to which a message handler is
attached.
13922
BAD RESTART ORDER
Attempt to restart an actor that is not frozen.
13923
ARGUMENTS INCONSISTENCY
The combination of some of the call arguments is
inconsistent.
13924
UNDEFINED DEFAULT MAPPER
The system default mapper is not defined.
13925
ADDRESS SPACE VIOLATION
Attempt to allocate a region outside the valid range of
virtual addresses for the address space.
13926
Issue: 30-0
REGION ACCESS RIGHTS VIOLATION
DN987378
607
Error messages
General Error Messages of System
Attempt to write in a read-only region.
13927
REGION OVERLAPPING
Attempt to allocate a memory region that would overlap
with another.
13928
BAD SEGMENT OFFSET
Attempt to map an impossible part of a segment.
13929
NON EMPTY ADDRESS SPACE
Attempt to duplicate regions within a non-empty address
space.
13930
MAPPER ACCESS ERROR
Unable to access a mapper.
13931
ABORTED RPC NOTIFICATION
Aborted RPC notification (K_EABORTRPC).
13932
MEMORY LOCKING CONFLICT
Attempt to flush a part of a local cache locked in memory.
13933
INCONSISTENT SIZE ARGUMENTS
The size given in parameter is incompatible with other
parameters.
13934
INVALID ADDRESSING MODE
Attempt to send a message with an invalid addressing
mode.
13935
PRIVILEGE VIOLATION
Attempt to perform a forbidden operation.
13936
ADDRESS CONFLICT
Attempt to allocate a memory region overlapping another.
13937
ALIGNMENT ERROR
Attempt to allocate a memory region whose starting
address is not aligned on a page boundary.
13938
SYSTEM QUEUES SATURATED
An ipcSend, ipcReply or ipcCall failed because the local
destination port queue is full or the local communication
system is saturated.
13939
608
ABORTED WAIT
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Abortable calls (e.g. ipcReceive, ipcCall, threadSuspend)
have been interrupted because the waiting thread has
been aborted.
13940
TRANSACTION FAILED
A system call failed because the actor which received the
request failed.
13941
IPC TIME-OUT
A system call failed because a time-out has occurred.
13942
UNREACHABLE DESTINATION
Attempt to send a RPC request to an unreachable port.
13943
NOT IMPLEMENTED (CHORUS)
The call or one of its options is not implemented in the
current version.
13944
BAD ADDRESS
The kernel encountered a hardware access fault in
attempting to access one of the arguments of the call.
13945
PORT DELETED
The port local identifier is invalid (the port was never
created or was deleted or has migrated before or during
the call).
13946
MESSAGE TOO BIG
Attempt to send a message body longer than
K_CMSGSIZEMAX bytes.
13947
OUT OF RESOURCE
The kernel has been unable to perform the call because of
resource exhaustion.
13948
INVALID ARGUMENT
An invalid argument has been given.
13949
NO ERROR
The call returned successfully.
13951
NO ERROR (POSIX)
No error.
13952
Issue: 30-0
OPERATION NOT PERMITTED
DN987378
609
Error messages
General Error Messages of System
An attempt was made to perform an operation limited to
processes with appropriate privileges or to the owner of a
file or other resource.
13953
NO SUCH FILE OR DIRECTORY
A component of a specified pathname did not exist, or the
pathname was an empty string.
13954
NO SUCH PROCESS
No process could be found corresponding to that specified
by the given process ID.
13955
INTERRUPTED SYSTEM CALL
An asynchronous signal (such as SIGINT or SIGQUIT)
was caught by the process during the execution of an
interruptible function. If the signal handler performs a
normal return, the interrupted function call will seem to
have returned the error condition.
13956
INPUT/OUTPUT ERROR
Some physical input or output error occurred. This error
will not be reported until a subsequent operation on the
same file descriptor and may be lost (overwritten) by any
subsequent errors.
13957
DEVICE NOT CONFIGURED
Input or output on a special file referred to a device that did
not exist, or made a request beyond the limits of the
device. This error may also occur when, for example, a
tape drive is not online or a disk pack is not loaded on
drive.
13958
ARGUMENT LIST TOO LONG
The sum of number of bytes used by the new process
images argument list and environment list was greater
than the system-imposed limit.
13959
EXEC FORMAT ERROR
A request was made to execute a file that, although it had
the appropriate permissions, was not in the format required
by the implementation for executable files.
13960
BAD FILE DESCRIPTOR
A file descriptor argument was out of range, referred to no
open file, or a read (write) request was made to a file that
was only open for writing (reading).
13961
610
NO CHILD PROCESSES
DN987378
Issue: 30-0
General Error Messages of System
Error messages
A wait() or waitpid() function was executed by a process
that had no existing or unwaited-for child processes.
13962
RESOURCE DEADLOCK AVOIDED
An attempt was made to lock a system resource that would
have resulted in a deadlock situation.
13963
CANNOT ALLOCATE MEMORY
The new process image required more memory than was
allowed by the hardware or by system-imposed memory
management constraints.
13964
PERMISSION DENIED
An attempt was made to access a file in a way forbidden
by its file access permissions.
13965
BAD ADDRESS(EFAULT)
The system detected an invalid address in an attempt to
use an argument of a call.
13966
BLOCK DEVICE REQUIRED
The block device is required (ENOTBLK).
13967
DEVICE BUSY
An attempt was made to use a system resource that was
not available at the time because it was being used by a
process in a manner that would have conflicted with the
request being made by this process.
13968
FILE EXISTS
An existing file was specified in an inappropriate context.
13969
CROSS-DEVICE LINK
A link to a file on another file system was attempted.
13970
OPERATION NOT SUPPORTED BY DEVICE
The operation is not supported by the device (ENODEV).
13971
NOT A DIRECTORY
A component of the specified pathname existed, but it was
not a directory, when a directory was expected.
13972
IS A DIRECTORY
An attempt was made to open a directory with write mode
specified.
13973
Issue: 30-0
INVALID ARGUMENT(EINVAL)
DN987378
611
Error messages
General Error Messages of System
Invalid argument (EINVAL)
13974
TOO MANY OPEN FILES IN SYSTEM
Too many files are currently open in the system. The
system reached its predefined limit for simultaneously
open files and temporarily could not accept requests to
open another one.
13975
TOO MANY OPEN FILES
An attempt was made to have the link count of a single file
exceed the set limit.
13976
INAPPROPRIATE IOCTL FOR DEVICE
A control function was attempted for a file or a special file
for which the operation was inappropriate.
13977
TEXT FILE BUSY
The new process was a pure procedure (shared text) file
which was open for writing by another process, or while
the pure procedure file was being executed in an open-call
requested write access. (This message is obsolete)
13978
FILE TOO LARGE
The size of a file would exceed an implementation-defined
maximum file size.
13979
NO SPACE LEFT ON DEVICE
During a write() function on a regular file, or when
extending a directory, there was no free space left on the
device.
13980
ILLEGAL SEEK
A lseek() function was issued on a pipe or FIFO.
13981
READ-ONLY FILE SYSTEM
An attempt was made to modify a file or a directory on a
file system that was read-only at that time.
13982
TOO MANY LINKS
Too many links (EMLINK)
13983
BROKEN PIPE
A write was attempted on a pipe or FIFO for which there
was no process to read the data.
13984
612
NUMERICAL ARGUMENT OUT OF DOMAIN
DN987378
Issue: 30-0
General Error Messages of System
Error messages
An input argument was outside the defined domain of the
mathematical function.
13985
RESULT TOO LARGE
The result of a function was too large to fit in the available
space.
13986
RESOURCE TEMPORARILY UNAVAILABLE
Resource unavailable or would
block(EAGAIN/EWOULDBLOCK). This is a temporary
condition, and later calls to the same routine may complete
normally.
13987
OPERATION NOW IN PROGRESS
An operation that takes a long time to complete (such as a
connect()) was attempted on a nonblocking object.
13988
OPERATION ALREADY IN PROGRESS
An operation was attempted on a non-blocking object that
already had an operation in progress.
13989
SOCKET OPERATION ON NON-SOCKET
The socket operation is on non-socket (ENOTSOCK).
13990
DESTINATION ADDRESS REQUIRED
A required address was omitted from an operation on a
socket.
13991
MESSAGE TOO LONG
A message sent on a socket was larger than the internal
message buffer or some other network limit.
13992
PROTOCOL WRONG TYPE FOR SOCKET
A protocol was specified that does not support the
semantics of the socket type requested. For example, you
cannot use the ARPA Internet UDP protocol with type
SOCK_STREAM.
13993
PROTOCOL NOT AVAILABLE
A bad option or level was specified in a getsockopt or
setsockopt call.
13994
PROTOCOL NOT SUPPORTED
The protocol has not been configured into the system or no
implementation for it exists.
13995
Issue: 30-0
SOCKET TYPE NOT SUPPORTED
DN987378
613
Error messages
General Error Messages of System
The support for the socket type has not been configured
into the system or no implementation for it exists.
13996
OPERATION NOT SUPPORTED
The attempted operation is not supported for the type of
object referenced. Usually this occurs when a file
descriptor refers to a file or socket that cannot support this
operation, for example, trying to accept a connection on a
datagram socket.
13997
PROTOCOL FAMILY NOT SUPPORTED
The protocol family has not been configured into the
system or no implementation for it exists.
13998
ADDRESS FAMILY NOT SUPPORTED BY PROTOCOL
An address incompatible with the requested protocol was
used. For example, you should not necessarily expect to
be able to use NS addresses with ARPA Internet protocols.
13999
ADDRESS ALREADY IN USE
Only one usage of each address is normally permitted.
14000
CANNOT ASSIGN REQUESTED ADDRESS
The specified address is not available on this machine.
14001
NETWORK IS DOWN
A socket operation encountered a dead network.
14002
NETWORK IS UNREACHABLE
Network is unreachable (ENETUNREACH).
14003
NETWORK DROPPED CONNECTION ON RESET
The host you were connected to crashed and rebooted.
14004
SOFTWARE CAUSED CONNECTION ABORT
A connection abort was caused internal to your host
machine.
14005
CONNECTION RESET BY PEER
A connection was forcibly closed by a peer. This normally
results from a loss of the connection on the remote socket
due to a timeout or a reboot.
14006
NO BUFFER SPACE AVAILABLE
An operation on a socket or pipe was not performed
because the system lacked sufficient buffer space or
because a queue was full.
614
DN987378
Issue: 30-0
General Error Messages of System
14007
Error messages
SOCKET IS ALREADY CONNECTED
A connect request was made on an already connected
socket. Or, a sendtoor sendmsg request on a connected
socket specified a destination when already connected.
14008
SOCKET IS NOT CONNECTED
A request to send or receive data was disallowed because
the socket was not connected and (when sending on a
datagram socket) no address was supplied.
14009
CANNOT SEND AFTER SOCKET SHUTDOWN
A request to send data was disallowed because the socket
had already been shut down with a previous shutdown call.
14010
TOO MANY REFERENCES: CANNOT SPLICE
There are too many references: cannot splice
(ETOOMANYREFS).
14011
OPERATION TIMED OUT
A connect or send request failed because the connected
party did not properly respond after a period of time. (The
timeout period is dependent on the communication
protocol.)
14012
CONNECTION REFUSED
No connection could be made because the target machine
actively refused it. This usually results from trying to
connect to a service that is inactive on the foreign host.
14013
TOO MANY LEVELS OF SYMBOLIC LINKS
Too many levels of symbolic links (ELOOP)
14014
FILE NAME TOO LONG
The size of a pathname exceeded the maximum and no
truncation mechanism was in effect for that file.
14015
HOST IS DOWN
Host is down (EHOSTDOWN).
14016
NO ROUTE TO HOST
No route to host (EHOSTUNREACH).
14017
DIRECTORY NOT EMPTY
A directory with entries other than dot and dot-dot was
supplied when an empty directory was expected.
14018
Issue: 30-0
TOO MANY PROCESSES
DN987378
615
Error messages
General Error Messages of System
There are too many processes.
14019
TOO MANY USERS
There are too many users. The quota system ran out of
table entries.
14020
DISC QUOTA EXCEEDED
A write to an ordinary file, the creation of a directory or
symbolic link, or the creation of a directory entry failed
because the users quota of disk blocks was exhausted, or
the allocation of an inode for a newly created file failed
because the users quota of inodes was exhausted.
14021
STALE NFS FILE HANDLE
An attempt was made to access an open file (on an NFS
filesystem) which is now unavailable as referenced by the
file descriptor. This may indicate that the file was deleted
on the NFS server or some other catastrophic event
occurred.
14022
TOO MANY LEVELS OF REMOTE IN PATH
Too many levels of remote in path (EREMOTE).
14023
RPC STRUCT IS BAD
Exchange of RPC information was unsuccessful.
14024
RPC VERSION WRONG
The version of RPC on the remote peer is not compatible
with the local version.
14025
RPC PROG. NOT AVAILALE
The requested program is not registered on the remote
host.
14026
PROGRAM VERSION WRONG
The requested version of the program is not available on
the remote host (RPC).
14027
BAD PROCEDURE FOR PROGRAM
An RPC call was attempted for a procedure which does
not exist in the remote program.
14028
NO LOCKS AVAILABLE
A system-imposed limit on the number of simultaneous file
and record locks was reached, and no more were available
at that time.
616
DN987378
Issue: 30-0
General Error Messages of System
14029
Error messages
FUNCTION NOT IMPLEMENTED
An attempt was made to use a function that is not available
in this implementation.
14030
INAPPROPRIATE FILE TYPE OR FORMAT
Inappropriate file type or format (EFTYPE)
14031
AUTHENTICATION ERROR
Authentication error (EAUTH)
14032
NEED AUTHENTICATOR
Authenticator is needed (ENEEDAUTH).
14102
CONFLICT IN CIS SSI
There is a conflict in CIS SSI. The given value of SSI is out
of the allowed range.
14104
DELETION OF DXT IS NOT ALLOWED BECAUSE DXT
IS THE MASTER OF SUBNET
Deletion of DXT is not allowed because the DXT is the
master of subnet.
14105
DELETION OF DXT IS NOT ALLOWED BECAUSE DXT
IS A MEMBER OF SUBNET
Deletion of DXT is not allowed because the DXT is a
member of the subnet.
14106
PROGRAM NOT FOUND
The requested program is not found.
14107
SPECIFIED ORGRANGE ALREADY EXISTS
The specified orgrange already exists.
14108
SPECIFIED DXT IS NOT IN ANY SUBNET
The specified DXT is not in any subnet.
14109
INVALID KEY FLAG VALUE
The value for the key flag is incorrect.
14110
REMOVING DXT IS NOT ALLOWED BEFORE (FIXED
NETWORK) CIRCUIT GROUP IS REMOVED
Removing DXT is not allowed before (fixed network) circuit
group is removed.
14111
Issue: 30-0
VPI RANGE IS NOT FREE
DN987378
617
Error messages
General Error Messages of System
There is at least one VPLtp in the specified VPI range.
Specify a different range or remove the existing VPLtps in
the range.
14112
SEMANTICS CHECK IS FAILED
Semantics check is failed.
14113
PREPROCESSOR STARTUP FAILURE
The preprocessor does not notice of its restart in time by
sending a message prepro_starting_notice_s.
14114
CONFIGURATION FAILURE OF A PREPROCESSOR
There is a configuration failure of a preprocessor.
14115
STARTUP TIMEOUT OF A PREPROCESSOR
The startup of a preprocessor takes too long a time.
14116
ILLEGAL ROGLIB LIBRARY FUNCTION CALL IN THIS
COMPUTER UNIT
There are different ROGLIB libraries for different processor
units. AllROGLIB services are not implemented in every
ROGLIB library. This error code is returned when the
program calls a ROGLIB library function illegal in the unit.
14117
GENERAL FAILURE IN CIS CORE HAPPENED
General failure code for errors occurring in CIS Core
14118
SERVICE IS RESERVED
Remote backup transfer is reserved, transfer or fallback is
in progress.
14119
DIRECTORY THAT SHOULD NOT EXIST IS FOUND
Directory that is tried to create already exists. Directory
must be deleted or renamed if transfer service is used.
14120
TRANSFER SERVICE HAS NOT BEEN ASKED
Readiness of transfer is asked even though preparation
have not been asked.
14121
SYSTEM IS NOT READY FOR TRANSFER
System has not done all needed preparation to transfer.
14122
THERE IS NO TRANSFER LIST IN FB BUILDS
DIRECTORY
Transfer list can not be found from FB builds SCMANA
directory.
618
DN987378
Issue: 30-0
General Error Messages of System
14123
Error messages
TRANSFER SERVICE CAN NOT BE STARTED
Conditions for starting transfer service do not come true.
14124
COMPRESSION SERVICE HAS RETURNED AN ERROR
Error occured in compression service.
14125
ERROR IN FINISHING TRANSFER SERVICE
An error occurred in the transfer services finishing task.
14126
RECORD NOT IN CNMREP REPORT FILE
Record not in CNMREP report file.
14127
CONFLICT IN GATEWAY SSI
There is a conflict in gateway SSI.
14128
DISK UNIT WORKING STATE HAVE CHANGED
Configuration of units with disks is changed after last FULL
fallback copy. DATA or ARCHIVE fallback copying could
not be executed because last FULL fallback copy was
done when different disk units were in WO-EX states.
Working state of unit with disks is changed, a new unit with
disks is created or a unit with disks is removed. FULL
fallback copying has to be done next.
14129
ROUTING AREA NOT FOUND FROM RNW DATABASE
Routing Area for the given routing area identification is not
found from RNW database (BSDATA).
14130
ROUTING AREA ID ALREADY IN USE
A Routing Area Identification must be unique in the BSC.
14131
INVALID MMI USER
MMI user has been detected to be invalid for the purpose
at issue.
14132
ILLEGAL TYPE OF VCC
Illegal or unknown type of the vcc. The service request is
rejected.
14133
TRX CAN NOT BE SUPER-REUSED AND E-TRX OR STRX SIMULTANEOUSLY
TRX CAN NOT BE SUPER-REUSED AND E-TRX OR STRX SIMULTANEOUSLY
14134
Issue: 30-0
TRX CAN NOT BE FLOATING AND EXTENDED
SIMULTANEOUSLY
DN987378
619
Error messages
General Error Messages of System
TRX cannot be floating and extended simultaneously.
14135
UNKNOWN CHORUS ERROR CODE
Chorus to DMX error code conversion routine received an
invalid Chorus error code.
14136
UNKNOWN ERROR RETURNED BY KERNEL
Unknown error returned by kernel.
14137
SITE NOT REACHABLE
Site not reachable.
14138
SYSTEM CALL NOT IMPLEMENTED
System call not implemented.
14139
SYSTEM CALL NOT SUPPORTED
System call not supported.
14140
UNKNOWN ERROR RETURNED BY IO SERVER
Unknown error returned by IO server.
14141
ERROR WHILE DELETING NETWORK USER
The network operation access control manager could not
delete network user. Use commands in IO-command group
to delete network user or to get more information.
14142
NO RECORDS FOUND WITH GIVEN LAC IN DATABASE
No records were found in the database with the given
location area code.
14143
RECORD WITH GIVEN SGSN_CELL_ID FOUND IN LAC
AND CELL OBJECT COLLECTIONS IN THE DATABASE
An attempt was made to create LAC and CELL objects
that already exist in the database.
14144
NO RECORDS FOUND WITH GIVEN NSEI IN NSE
OBJECT COLLECTION
No records were found with the given network service
entity identifier in the NSE object collection.
14145
RECORD WITH GIVEN NSEI AND BVCI FOUND IN NSE
AND CELL OBJECT COLLECTIONS IN DATABASE
An attempt was made to create NSE and CELL objects
that already exist in the database.
14146
620
LACS WITH CELLS FOUND FOR GIVEN VLR IN LAC
AND CELL OBJECT COLLECTIONS IN DATABASE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The requested operation is not allowed because LACs with
CELLs for the given VLR are found in LAC and CELL
object collections.
14147
LAC IS ALREADY ASSOCIATED WITH ANOTHER VLR
The requested operation is not allowed, because the given
LAC already exists in the database, associated with
another VLR.
14148
NO CELLS FOUND WITH GIVEN KEY VALUE(S) OR
OBJECT NUMBER VALUE IN DATABASE
No cells were found with the given key value(s) or object
number value.
14149
A PLMN OBJECT ALREADY DEFINED AS HOME PLMN
FOUND IN DATABASE
Only one PLMN object can be defined as "Home PLMN".
14150
GRSLIB CALL IS NOT ALLOWED IN UNIT
An attempt was made to call the GRSLIB library in a unit
where it is not allowed.
14151
NO MORE KEYS AVAILABLE
The key table is full, no keys can be created.
14152
OUT OF RESOURCES
The kernel has been unable to perform the call because of
resource exhaustion.
14153
INVALID PRIVATE DATA ARGUMENT
An invalid argument has been given.
14154
CANNOT CONNECT TO SERVER
The Private Data Manager is not accessible.
14155
CALLED FROM USER MODE
Called from user mode.
14156
FILE END MARK NOT FOUND
The end mark of the file is not found.
14157
GIVEN ORGRANGE OVERLAPPED WITH EXISTING
RANGES
The given orgrange overlapped with existing ranges.
14158
Issue: 30-0
STATIC ADDRESS IS STILL ASSIGNED
DN987378
621
Error messages
General Error Messages of System
The static address exists, cannot delete the subnet.
14159
ORGANIZATION RANGE IS STILL ASSIGNED
A dynamic address exists, cannot delete the subnet.
14160
THERE IS NO GATEWAY DXT IN A SUBNET
There is no gateway DXT in a subnet.
14161
THE SUBNET OVERLAPS WITH AN EXISTING SUBNET
The AIP subnet overlapped.
14162
CANNOT DECREASE THE SIZE OF AN EXISTING
SUBNET
The subnet mask cannot be narrowed.
14163
CHANGING OF ARFCN IS NOT ALLOWED IN
BACKGROUND SWAPPING WHEN TRX IS WAITING
FOR APP
If the value of TRX FREQ (ARFCN) parameter is "not
used", the TRX is waiting for Automatic PicoCell
Parameterization (APP), and the value cannot be changed
in the background loading of the radio network plan.
14164
WRONG MESSAGE RECEIVED
Message that was not expected has been received.
14165
SPECIFIED DYNAMIC ADDRESS PAIR CANNOT BE
FOUND
The specified dynamic address pair cannot be found.
14166
GPRS AND EDGE FEATURES ARE NOT IN USE IN BSC
GPRS and EDGE features are not in use in BSC.
14167
NO DXT DEFINITIONS IS FOUND FROM TXDATA
DATABASE
There are no DXT definitions found from TXDATA
database.
14168
PRIVATE-DATA CALL SUCCESSFUL
PRIVATE-DATA call successful.
14169
REQUIRED TOPOLOGY DATA ARE MISSING
The internal network topology can not be build due to
inconsistent internal data or missing pids (process
identificators)
14170
622
INVALID CIRCUIT GROUP NAME
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Circuit group name is not given.
14171
PARAMETER CHECKING FAILED
Checking of parameter failed.
14172
INVALID CIRCUIT FORMAT
Invalid circuit format.
14173
INVALID CALL CONTROL PARAMETER SET
Invalid call control parameter set.
14174
INVALID DUAL SEIZURE PREVENTION METHOD
Invalid dual seizure prevention method.
14175
INVALID PARAMETER HUNTED
Invalid parameter hunted.
14176
SWITCHING DATA UPDATE FAILED
Switching data update failed.
14177
THRESHOLD 2 IS BIGGER THAN THRESHOLD 1
Threshold 2 is bigger than threshold 1.
14178
CIRCUIT GROUP NAME AND NUMBER DO NOT MATCH
Circuit group name and number refer to different circuit
groups.
14179
NO CIRCUITS GIVEN
No circuits given.
14180
INVALID PCM NUMBER
Invalid PCM number given.
14181
INVALID CCSPCM
Invalid ccspcm given.
14182
PCM DEFINED TO OTHER CCSPCM
PCM already defined to other ccspcm.
14183
INVALID D-CHANNEL SYSTEM
Invalid D-channel system.
14184
CIRCUIT IDENTIFICATION CODE VALUE TOO BIG
Too big a circuit identification code value.
Issue: 30-0
DN987378
623
Error messages
General Error Messages of System
14185
INVALID TREE
Invalid analysis tree given.
14186
NETWORK AND LINE SIGNALLING DO NOT MATCH
Given network and line signalling do not match.
14187
INVALID NETWORK
Invalid network given.
14188
WRONG TYPE OF TRANSCODER
Wrong type of transcoder.
14189
INTERFACE AND LINE SIGNALING DO NOT MATCH
Interface and line signaling do not match.
14190
PBX SUPPLEMENTARY SERVICES
The circuit group has supplementary services and cannot
be deleted before the services are removed.
14191
CIRCUIT COUNTERS ON
Circuit(s) in circuit group has counters on.
14192
INVALID NUMBER OF PCMS
Invalid number of PCMs.
14193
INVALID NUMBER OF CIRCUITS
Invalid number of circuits.
14194
INVALID CIRCUIT IDENTIFICATION CODE
Invalid circuit identification code.
14195
INCORRECT FREQUENCY FOR A TRX WHEN
UNLOCKING IS ATTEMPTED
When the unlocking of a TRX is attempted and the
frequency is incorrect,the unlocking will not be
acknowledged by ABIPRB.
14196
INVALID VALUE IN FIELD FREE_RESERV
Value of field free_reserv out of range.
14197
INVALID NUMBER OF CIRCUIT IDENTIFICATION
CODES
Invalid number of circuit identification codes.
14198
624
PXADMI BUSY
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The program block PXADMI is not capable of receiving
new tasks. Try again later.
14199
NO FREE RECORDS IN DCHSET FILE
No free records in DCHSET file.
14200
NO FREE RECORD EXISTS IN FUDCHA FILE
No free record exists in FUDCHA file.
14201
NO FREE RECORDS IN SDCHAN FILE
There are no free records in the SDCHAN file.
14202
NO FREE RECORDS IN DPCONF FILE
No free records in DPCONF file.
14203
MAXIMUM NUMBER OF DXTS ARE ALREADY
CONNECTED WITH INTEREXCHANGE SPEECH LINES
Maximum number of DXTs, which can be connected with
interexchange speech line connection to this DXT, is
defined the general type DXT_HW_LIM_T.
14204
APP OPTION IS NOT IN USE IN BSC
This error code OPTION_APP_NOT_IN_USE_EC
(Automatic PicoCell Parametrisation) indicates that the
option is not in use in BSC.
14205
UNKNOWN ERROR CODE
The argument given to an error code conversion function
in CXELIB is not one of the valid error code numbers in
ChorusOS.
14206
THE SITE TYPE DOES NOT ALLOW
SYNCHRONISATION
The site type of adjacent cell BTS or this cell BTS does not
allow synchronisation between adjacent cell and the cell in
use. The user cannot give the value Y to the SYNC
parameter when creating or modifying an adjacent cell if
the site type of BTS does not support synchronisation
between cells.
14207
THE RECORD WAS ONLY PARTLY READ/WRITTEN
The filesystem read/wrote only part of a record
14208
MAXIMUM NUMBER OF HTTP SESSIONS FROM SAME
USER EXCEEDED
Maximum number of HTTP sessions from one user has
exceed.
Issue: 30-0
DN987378
625
Error messages
General Error Messages of System
14209
THERE IS NO KEY ATTACHED TO ISSI IN THE
COLLECTION
There is no key attached to ISSI in the collection.
14210
THERE IS NO KEY ATTACHED TO EI IN THE
COLLECTION
There is no key attached to EI in the collection.
14211
O&M OR TRX LINK CIRCUITS RESERVATION BACK TO
THE POOL FAILED
Reservation of the O&M or TRX link circuits back to the
pool has failed.
14212
SPEECH CIRCUITS RESERVATION BACK TO THE
POOL FAILED
Reservation of the speech circuits back to the pool has
failed.
14213
TRX LINK AND TRX SPEECH CIRCUITS RESERVATION
BACK TO THE POOL FAILED
Reservation of the TRX link and TRX speech circuits back
to the pool has failed.
14214
CELL DOES NOT HAVE MAIN CONTROL CHANNEL
There is no ttrx_of_cc relation for the given cell in
database indicating that the given cell does not have main
control channel.
14215
DEFINED PROFILE NOT FOUND
Data profile attached to subscriber is not found or data
profile does not exist in the database.
14216
DEFINED PROFILE ALREADY EXISTS
Defined profile already exists in database.
14217
IP SUBNET MASK IS INVALID OR INCOMPATIBLE WITH
THE SUBNET
The IP network address and IP network mask are
incompatible, or the mask is not in proper format.
14218
STATIC/DYNAMIC BOUNDARY (NETDIVIDER) IS
INVALID
The static/dynamic boundary (also known as NetDivider) is
invalid, which is outside of the current subnet.
14219
DBP INTERNAL ERROR
An internal error has occurred in the DBPLIB library.
626
DN987378
Issue: 30-0
General Error Messages of System
14220
Error messages
SMSC ADDRESS ANALYSIS NOT FOUND
There is no SMSC address analysis in the analysis tree.
14221
STATISTICS RESET FAILED
The attempt to reset the statistics failed.
14222
THE MAXIMUM NUMBER OF NS-VC/NS-VL IN THE NSE
EXCEEDED
The maximum number of Network Service Virtual
Connection (NS-VC) in the Network Service Entity (NSE)
is exceeded
14223
DELETION OF THE LAST NS-VC OF NSE USED BY
GPRS-ENABLED BTS IS NOT POSSIBLE
Deletion of the last ns-vc of nse used by GPRS-enabled
BTS is not possible.
14224
NAME OF NS-VC IS ILLEGAL
The name of NS-VC may consist of allowed characters
only.
14225
THE NAME OF NS-VC IS ALREADY IN USE IN THE BSC
The name of NS-VC must be unique in the BSC.
14226
NS-VC OBJECT NOT FOUND IN DATABASE
NS-VC object was not found in the radio network
database.
14227
TERMINATION POINT IS PRERESERVED
Termination point is prereserved. The requested operation
is not allowed to this termination point.
14228
GPRS IS ENABLED IN THE CELL
General Packet Radio System function is in active state in
the cell.
14229
NO RECORDS FOUND WITH GIVEN TERMS IN NSE
OBJECT COLLECTION
No records found with given terms in NSE object
collection.
14230
CONTROL CHANNEL RELEASE DISALLOWED
Control channel release is not allowed. The protocol state
inside the control channel prohibits release. Try again
release with an override parameter if you are absolutely
sure that the channel can be released despite of the
protocol state.
Issue: 30-0
DN987378
627
Error messages
General Error Messages of System
14231
NSE OF NS-VC HAS DIFFERENT PACKET CONTROL
UNIT ADDRESS IN DATABASE
There exists already an NSE with the same NSEI but
different Packet Control Unit Address in the radio network
database.
14232
ADDRESS OF PCU IS ALREADY USED BY OTHER GBINTERFACE
Address of Packet Control Unit is already used by some
other Gb-interface
14233
NS-VCS FOUND FOR GIVEN NSEI IN NS-VC OBJECT
COLLECTION
The requested operation is not allowed because the NSVCs associated with the given NSEI are found in NS-VC
object collection.
14234
CELLS FOUND FOR GIVEN NSEI IN CELL OBJECT
COLLECTION
The requested operation is not allowed because CELLs
associated with the given NSEI are found in CELL object
collection.
14235
SHADOWS TRANSACTION IS READ-ONLY
An attempt was made to make some form of update
operation in the Shadows database engine using a readonly transaction. Likely caused by a transaction started on
a snapshot.
14236
PRINTER ALREADY EXISTS
Printer device to be created already exists.
14237
NO SUCH PRINT TASK
Task ID given in remove task cannot be found.
14238
TASK UNDER EXECUTION DOES NOT EXIST
No task ID is given in remove task and LPD does not have
a printing task under execution.
14239
HEADING TOO LONG
Given data exceeds maximum length of heading.
14240
CHANNEL FINDER OPTION IS NOT IN USE IN BSC
The Channel Finder option is not in use in the BSC. The
Channel Finder registers statistics on cells which have not
been defined as adjacent cells but which are among those
six neighbouring cells, that the MS receives best.
628
DN987378
Issue: 30-0
General Error Messages of System
14241
Error messages
DB VALUE IS INCORRECT
The DB-value is incorrect. DB-value is out of range or DB1
is bigger than DB2 or DB-values are same.
14242
NS-VC DOES NOT EXIST IN PCU
The Network Service Virtual Connection does not exist in
PCU.
14243
NSEI DOES NOT EXIST
The Network Service Entity Identifier does not exist.
14244
NS-VCI ALREADY EXISTS
The Network Service Virtual Connection Identifier already
exists.
14245
NS-VC NAME ALREADY EXISTS
The name of the Network Service Virtual Connection
already exists.
14246
NO FREE NS-VC AVAILABLE IN NSE
All NS-VCs of the NSE are already in use.
14247
NS-VC NOT LOCKED
The Network Service Virtual Connection has not been
locked.
14248
NS-VC ALREADY LOCKED
The Network Service Virtual Connection is already locked.
14249
NS-VC ALREADY UNLOCKED
The Network Service Virtual Connection is already
unlocked.
14250
NS OPERATION FINISHED
The Network Service specific operation is finished.
14251
PAPU ADDRESSES NOT IDENTICAL IN NSE AND
BEARER
PAPUs logical unit addresses are not identical with each
other in the created NSE and in the bearer channel.
14252
NO RESPONSE FROM FRADMI
No response has been received from the FRADMI
process.
14253
Issue: 30-0
NO RESPONSE FROM GGBPRB
DN987378
629
Error messages
General Error Messages of System
No response has been received from the GGBPRB
program block.
14254
CIRS SUM IS GREATER THAN ACCESS RATE
The sum of committed information rates of virtual circuits is
greater than the access rate of the bearer channel.
14255
DATA CORRESPONDING TO THE GIVEN INPUT
PARAMETERS NOT FOUND
Data corresponding to the given input parameters is not
found.
14256
THE FILE IS NOT A VALID COMPRESSION ARCHIVE
The file in question is not a compression archive or is a
corrupted archive.
14257
THE FILES DO NOT FIT INTO THE ARCHIVE WITH THE
GIVEN ALLOCATION RATIO
The files cannot be compressed enough to fit into the
archive with the given allocation ratio. Use a bigger ratio.
14258
THE SETTING OF FTAM ATTRIBUTES OF THE
ARCHIVE HAS FAILED
The setting of FTAM attributes of the archive has failed.
However, a valid compression archive was created.
14259
SOME OF THE RQUIRED FILES WERE NOT HANDLED
PROPERLY
When compressing a list of files, some of the given files
could not be accessed. However, a valid compression
archive consisting of the accessible files was created.
When decompressing files, some of the requested files
could not be decompressed, but the rest of the files were
successfully decompressed.
14260
TARGET OF THE OPERATION HAS NO DEFINED
OPERATING STATE
The target of the operation has no defined operating state
and therefore e.g state inquiry cannot return the state.
14261
DEVICE ACCESS IS DENIED
The device is not accessible due to operating state or
insufficient permission.
14262
INVALID OPERATING STATE
The target is in a wrong operating state or you have tried
to change it to a wrong operating state.
630
DN987378
Issue: 30-0
General Error Messages of System
14263
Error messages
THE I/O UNIT STATE MANAGEMENT NOT READY
The I/O unit operating state management is not ready. It
has not yet successfully initialized.
14264
I/O DEVICE INDEX OUT OF RANGE
The device index of I/O unit exceeds the max index value.
14265
I/O DEVICE ALREADY EXISTS
The I/O unit has been already created.
14266
MMI PROFILE DOES NOT EXIST
The MMI profile does not exist.
14267
MEASUREMENT NOT STOPPED
The measurement has not been stopped.
14268
ERROR IN MEASUREMENT INTERVALS
Operation failed, error in measurement intervals.
14269
ILLEGAL BTS CONFIGURATION
Illegal BTS configuration (general cause value).
14270
NOT ALL MANDATORY SYSTEM INFORMATION
MESSAGES ARE RECEIVED BY TRX
TRX has not received all mandatory system information
messages.
14271
A SHADOWS DATABASE PAGE WAS NOT FOUND
Shadows internal error code. Indicates that a requested
page was not found in a page table or in a snapshot.
Encountered only as a result of a programming error within
Shadows.
14272
UKNOWN SHADOWS PAGE SIZE SPECIFIED
Shadows internal error. Indicates that an unknown page
size was specified. Encountered only as a result of a
programming error within Shadows.
14273
SHADOWS CACHE IS FULL
The Shadows cache is full.
14274
SHADOWS TRANSACTION EXCEEDED ITS MAXIMUM
UPDATE LIMIT
A Shadows transaction exceeded its maximum number of
updates.
Issue: 30-0
DN987378
631
Error messages
General Error Messages of System
14275
NEXT SHADOWS COMMIT BATCH IS FULL
The next Shadows commit batch is full.
14276
NO FREE SHADOWS TRANSACTIONS
There are no free Shadows transactions available.
14277
ILLEGAL INITIALIZATION VALUE FOR CCCH_CONF IN
SYTEM INFORMATION MESSAGE TYPE 3
Illegal initialization value for CCCH_CONF in system
information type 3.
14278
ILLEGAL INITIALIZATION VALUE FOR WHERE-FIELD IN
SYSTEM INFORMATION MESSAGE TYPE 3
Illegal initialization value for WHERE-field in system
information type 3.
14281
CONFLICT BETWEEN THE MAPPING OF SI13 AND
BCCH-EXT SIS
Conflict between the mapping of system information type
13 and BCCH-ext system information types.
14282
ILLEGAL INITIALIZATION VALUE FOR
DRX_TIMER_MAX FIELD IN SYSTEM INFORMATION
TYPE 13
Illegal initialization value for DRX_TIMER_MAX field in
system information type 13.
14283
ILLEGAL INITIALIZATION VALUE FOR
ACC_BURST_TYPE IN SYSTEM INFORMATION TYPE
13
Illegal initialization value for ACC_BURST_TYPE in
system information type 13.
14284
THE VALUE OF BS_AG_BLKS_RES CANNOT BE
CHANGED
The value of BS_AG_BLKS_RES cannot be changed at
run time.
14285
THE VALUE OF BS_PA_MFRMS CANNOT BE
CHANGED
The value of BS_PA_MFRMS cannot be changed at
runtime.
14286
THE VALUE OF CCCH_CONF CANNOT BE CHANGED
AT RUNTIME
The value of CCCH_CONF cannot be changed at runtime.
632
DN987378
Issue: 30-0
General Error Messages of System
14287
Error messages
SI13_PBCCH_LOCATION CANNOT BE CHANGED IN
SYSTEM INFORMATION TYPE 3 AND 4
SI13_PBCCH_LOCATION cannot be changed in system
information type 3 or 4at runtime.
14288
BCCH-EXT CANNOT BE CREATED
BCCH-ext cannot be created at runtime.
14289
BCCH-EXT CANNOT BE RELEASED
BCCH-ext cannot be released at runtime.
14290
THE VALUE OF DRX_TIMER_MAX CANNOT BE
CHANGED
The value of DRX_TIMER_MAX cannot be changed at
runtime.
14291
THE VALUE ACC_BURST_TYPE CANNOT BE
CHANGED
The value ACC_BURST_TYPE cannot be changed at
runtime.
14292
UNKNOWN COMPUTER UNIT FOR CONTROL
CHANNEL
Computer unit for control channel is given but computer
unit is not found or service provider on this computer is not
found. Select another computer unit and try again.
14293
CONTROL CHANNEL TYPE NOT SUPPORTED
Control channel type is not supported by the system.
Select another type and try again.
14294
CONTROL CHANNEL DOES NOT EXIST
Control channel does not exist. Select another which do
exist and try again.
14295
CONTROL CHANNEL TYPE FULL
All resources for given type are already reserved in
termination provider. Select another control channel type
or another termination provider.
14296
CONTROL CHANNEL EXIST
Control channel already exists in the system. Select
another and try again.
14297
TERMINATION PROVIDER IS FULL
All termination provider resources are already reserved.
Select another termination provider and try again.
Issue: 30-0
DN987378
633
Error messages
General Error Messages of System
14298
D-CHANNEL ACTIVATION NOT DENIED
The D-channel was not set into state "Activation denied"
before the deletion or modification of the signalling channel
was attempted.
14299
CRC ERROR IN A COMPRESSED FILE
At least one of the files in the compression archive has a
CRC error. This means that the compression archive might
be corrupted and should be dealt with caution.
14300
ACTOR DOES NOT EXIST
The actor does not exist or is not found in the supervision
data table.
14301
PORT DOES NOT EXIST IN CHORUS COMPUTER
The port does not exist or the port does not belong to the
actor.
14302
REGISTRATION OVERFLOW
Registration to the supervision does not succeed. The
supervision data table may be full.
14303
PACKING OF DISK PARTLY SUCCESSFUL
The packing of the disk was partly successful, some
fragments were removed from the disk.
14304
DISK ALREADY PACKED
The disk was already packed, there were no fragments in
it.
14305
DISK PACKING FAILED
The packing of the disk was unsuccessful. No fragments
were removed from the disk.
14306
DBL ERROR IN LOGBUFFER
There is an error in logbuffer.
14307
DBL- NO MORE TRANSACTIONS
There are no more transaction in the logbuffer.
14308
DBL - NO MORE UPDATES
There are no more updates in the transaction.
14309
634
GIVEN COMBINATION OF PCU ADDRESS AND PCU
INDEX NOT FOUND FROM RNW DATABASE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Given combination of logical address of BCSU where the
Packet Control Unit is located and the PIU index of Packet
Control Unit not found from Radio Network Database.
14310
COMMITTEDINFORATE IS NOT ONLY ATTRIBUTE TO
BE MODIFIED
The user tries to modify CommittedInfoRate and other
attributes at the same time
14311
MAX NUMBER OF NSE FOR PAPU ALREADY CREATED
The maximum number of NSEs for one PAPU is already
created.
14312
LACS NOT RELATED TO GIVEN VLR
No location area codes have been associated with the
given MSC/VLR.
14313
RA OR NSE IS WRONGLY CONFIGURED IN THE BSS
Either the routing area of the cell or the association
between the routing area and the network service entity is
wrongly configured in the BSS.
14314
RA OF CELL IS SERVED BY DIFFERENT PAPU
The routing area of the cell is served by a different Packet
Processing Unit.
14315
NSE CONFIGURATION ERROR
The Network Service Entity is configured to another Packet
Processing Unit.
14316
VLR DOES NOT EXIST
The MSC/VLR does not exist.
14317
NO RESPONSE FROM GMGPRB
No response has been received from the GMGPRB.
14318
NO RESPONSE FROM GSPPRB
No response has been received from the GSPPRB.
14319
NO RESPONSE FROM GS1PRB
No response has been received from the GS1PRB.
14320
NO RESPONSE FROM GIPPRB
No response has been received from the GIPPRB.
14321
Issue: 30-0
NO RESPONSE FROM GTPPRB
DN987378
635
Error messages
General Error Messages of System
No response has been received from the GTPPRB.
14322
NO RESPONSE FROM GDCPRB
No response has been received from the GDCPRB.
14323
NO RESPONSE FROM GRNPRB
No response has been received from the GRNPRB.
14324
COMMUNICATION ERROR WITH SSCOP
Response message is not received from the SSCOP.
14325
ANALYSIS LEADS TO TIME CONTROLLED ROUTING
Digit analysis leads to time controlled routing. The analysis
cannot beremoved, unless time controlled routing is
deleted first.
14327
DBL NOT PASSED FIRST TRANSACTION
The first transaction has not been passed.
14329
DBL NOT PASSED FIRST UPDATE
The first update has not been passed.
14330
NETWORK SERVICE ENTITY IS IN USE IN A CELL
Network service entity is used in a cell or cells by some
BTS or BTSs.
14331
COMMERCIAL OPTION NOT ALLOWED TO BE USED
This error code is returned when a commercial option (e.g.
IP Packet Data) is not allowed to be used.
14332
MAXIMUM NUMBER OF SUBSCRIPTIONS EXCEEDED
The upper limit for the number of subscriptions has been
reached. No more subscriptions can be placed until some
are removed.
14333
NUMBER OF LACS EXCEEDS THE NUMBER ALLOWED
FOR ONE VLR
An attempt was made to create more LACs than allowed in
association with one VLR.
14334
BVCI DOES NOT EXIST
The BSSGP virtual connection identifier is unknown.
14335
THERE IS NO UNBLOCKED NS-VC IN THE NSE
All NS-VCs of the NSE are blocked. The NSE cannot
handle packet data.
636
DN987378
Issue: 30-0
General Error Messages of System
14336
Error messages
BVC ALREADY EXISTS IN THE SYSTEM
The BSSGB virtual connection already exists in the
system.
14337
BVC DOES NOT BELONG IN THIS BLOCK
The BSSGP virtual connection does not belong in this
block in the BVCSTA file. It is not configured to the NSE.
14338
SOME MISMATCH IN GIVEN TRIGGERING
CONDITIONS
There are some mismatching values in given triggering
conditions.
14339
NSE IS FULL, NO ROOM FOR NEW BVC
The maximum number of BSSGP virtual connections has
been exceeded. There is no room for a new BVC in the
NSE.
14340
D-CHANNEL ACTIVATION FAILED
D-channel activation failed.
14341
D-CHANNEL BLOCKING FAILED
D-channel blocking failed.
14342
D-CHANNEL STATE CHANGE ALREADY ACTIVATED
D-channel state change already activated.
14343
D-CHANNEL STATE CHANGE NOT ALLOWED
D-channel state change not allowed.
14344
DATA MISMATCH BETWEEN PXNETM WORK FILE AND
AN OTHER D-CHANNEL FILE
Data mismatch between PXNETM work file and another Dchannel file.
14345
DATA MISMATCH BETWEEN PXNETM WORK FILE AND
AN OTHER DLC-CHANNEL FILE
Data mismatch between PXNETM work file and another
DLC-channel file.
14346
PXNETM PROGRAM BLOCK IS STARTING
The PXNETM program block is starting.
14347
Issue: 30-0
CPXSAL HAD TO CREATE NEW HAND WHEN LINK
WAS RESERVED WITH UPDATE PARAMETER ON
DN987378
637
Error messages
General Error Messages of System
CPXSAL received a link_init_req_s message with update
parameter as repair_c and could not find a hand with the
same control channel identifier from its tables. Thus a new
hand had to be created and this error code is sent to the
SSCF layer in the link_init_ack_s message.
14348
TOO MANY INDICES
Maximum number of indices reached.
14349
CONFLICTING INDICES
Conflicting indices.
14350
UNKNOWN INDEX
Unknown index.
14351
MAX NUMBER OF CELLS FOR PAPU ALREADY
CREATED
The maximum number of cells for one PAPU is already
created.
14352
GSTPRB IS BUSY. TRY AGAIN LATER.
GSTPRB is busy and cannot receive any messages.
GSTPRB ignored your attempt so you should try again
later.
14353
NONEXISTENT PROFILE
This is a general error code which indicates that the
defined profile does not exist.
14354
IDENTIFICATION NUMBER ALREADY EXISTS
This is a general error code which indicates the defined
profile ID already exists.
14355
UNFINISHED GPDATA OPERATION EXISTS
There is an unfinished parameter handling operation going
on in the GPDATA.
14356
TOO MANY ADDRESSES
Subsciber has too many addresses in database.
14357
PROFILE CONFLICT
There is no space to add given information to the profile or
update information conflicts with the existing content of the
profile.
14358
MAXIMUM NUMBER OF NSES EXCEEDED
There is no room for a new NSE in the system.
638
DN987378
Issue: 30-0
General Error Messages of System
14359
Error messages
OUTGOING CALL BARRING ANALYSIS
Handled analysis is outgoing call barring analysis
14360
CENTREX MULTINUMBER OUTGOING CALL
IDENTIFICATION ANALYSIS
Handled analysis is centrex multinumber outgoing call
identification analysis
14361
GIVEN ISDN PCM ALREADY EXISTS
Given ISDN PCM already exists.
14362
GIVEN ISDN PCM IS NOT FOUND
Given ISDN PCM is not found.
14363
TIMEOUT FOR LOADING A MODULE OCCURED
A timeout if the loading of a module lasts for more than 30
secs.
14364
DATA AREA FOR BLSLIB NOT FOUND
The data area reserved for BLSLIB is not found.
14365
NO UNIT FOR THE GIVEN LOAD LIST
There is no unit for the given load list in BLNAME.
14366
NO RESPONSE FROM GBNPRB
No response from GBNPRB.
14367
PCU ADDRESSES NOT IDENTICAL IN NSE AND
BEARER
The NSE and the bearer channel are not located to the
same PCU in the BSC.
14368
ISDN PCM CONTROL IS NOT OK
The controlling of ISDN PCM is not in order. The program
block SI1PRB should be responsible for controlling the
ISDN PCM.
14369
TPST UNIT IS NOT FOUND WITH THE GIVEN INDEX
TPST functional unit with the given unit index has not been
defined to the exchange.
14370
SIGNALLING LINK COMMAND STOP WAS RECEIVED
Upper layer, e.g. MTP-3, sent signalling link stop
command.
14371
Issue: 30-0
INITIAL ALIGNMENT WAS NOT SUCCESSFUL
DN987378
639
Error messages
General Error Messages of System
Connection establishment was not successful.
14372
REMOTE USER RELEASED THE CONNECTION
Remote level 3, e.g. MTP-3, released the connection.
14373
SSCOP RELEASED THE CONNECTION
Service Specific Connection Oriented Protocol (SSCOP)
released the connection.
14374
LAYER MANAGEMENT RELEASED THE CONNECTION
Layer management released the connection. The layer
management can be either local or remote.
14375
PROTOCOL ERROR OCCURED IN SAAL STACK
Illegal protocol messages were received in SAAL stack.
14376
MESSAGE NOT VALID IN STATE
The received message is not valid at the current state of
the receiver.
14377
ILLEGAL VALUE OF PARAMETER
One of the received parameter contained illegal value.
14378
TERMINAL ADDRESSING ERROR
Message was addressed to the wrong terminal.
14379
SIGNALLING LINK ADDRESSING ERROR
Message was sent to the wrong signalling link.
14380
NS-VC CREATION FAILED
The creation of a Network Service Virtual Connection has
failed in the Gb interface.
14381
NS-VC UNBLOCK FAILED
The attempt to unblock the Network Service Virtual
Connection by the user or by the system has failed in the
Gb interface.
14382
BVC CREATION HAS FAILED
The creation of the BSSGP virtual connection has failed in
the Gb interface.
14383
BVC UNBLOCK FAILED
The unblocking of the BSSGP virtual connection has failed
in the Gb interface.
640
DN987378
Issue: 30-0
General Error Messages of System
14384
Error messages
BVC BLOCK FAILED
The blocking of the BSSGP virtual connection has failed in
the Gb interface.
14385
BVC DELETION FAILED
The deletion of the BSSGP virtual connection has failed in
the Gb interface.
14386
MEASURED POWER LEVEL DIFFERS TOO MUCH
FROM DEFAULT
MEASURED POWER LEVEL DIFFERS TOO MUCH
FROM THE DEFAULT VALUE
14387
RX BRANCHES IN IMBALANCE; OTHER BRANCH
MALFUNCTIONING
RX branches in imbalance. Other branch is malfunctioning.
14388
TOO MUCH PHASE ERROR; SENSITIVITY NOT
MEASURED
Too much phase error. Sensitivity not measured.
14390
FILE IS BEING UPDATED
RIZRDS returns this error code when it receives a write
request targeted at a POSIX configuration file which is
currently being updated by another process
14391
OPERATION INTERRUPTED
RIZRDS was restarted and sufficient data to restart a given
task was not available.
14392
INVALID FILENAME OR PATH
The path and/or filename could not be parsed from the
parameter.
14393
WRITE REQUESTS ACCEPTED FROM OMU ONLY
POSIX configuration files can only be written by process
families residing in OMU.
14394
SIGNALLING ATM ADAPTATION LAYER FAILURE
Failure has occured in the internal functioning of Signalling
ATM Adaptation Layer.
14395
RESULT IS NOT WITHIN THRESHOLD VALUE RANGE
Result is not within threshold value range.
14396
Issue: 30-0
NO SI_END_ACK/NACK MESSAGE FROM TRX
DN987378
641
Error messages
General Error Messages of System
TRX has not responded to system information message
sending.
14397
OWN PREPROCESSOR INDEX IS UNKNOWN
DMX messaging system cannot allow applications to
register yet because the preprocessor index of the own
computer has not been defined.
14398
CXMANA MEMORY ALLOCATION ERROR
DMX messaging subsystem manager has run out of
memory, and cannot storeany more DMX identities.
14399
DYNAMIC FAMILY IDENTIFIERS EXHAUSTED
DMX messaging subsystem does not have any more
dynamic family identifiers available.
14400
NO FREE PROCESS IDENTIFIER
DMX messaging cannot allocate a process id from the
requested family because all available process ids are
already in use.
14401
DMX MESSAGE QUEUES EXHAUSTED
All message queues provided by DMX messaging
subsystem are already in use.
14402
REQUESTED DMX IDENTITY IS ALREADY IN USE
The requested DMX identity is already in use.
14403
DBL NOT AT THE FIRST TRANSACTION
Not at the first transaction
14404
DBL NOT AT THE FIRST UPDATE
Not at the first update
14405
ACCESS NOT ALLOWED IN THE CURRENT STATE
Access to the device is not allowed in the current state.
14406
SECONDARY ROUTE CANNOT BE THE SAME AS
DESTINATION DXT
The given secondary route cannot be the same as the
destination DXT.
14407
SECONDARY ROUTE CANNOT BE THE SAME AS
PRIMARY ROUTE
The given primary and secondary route cannot be the
same.
642
DN987378
Issue: 30-0
General Error Messages of System
14408
Error messages
REMOVAL OF PRINTER FAILED
Removal of printer from the system failed.
14409
NO CDSU OR ET WITH EC2ET ON THIS PCM
No CDSU, NDSD, NDSM or ET with EC2ET on this PCM.
14410
PX1WRK FILE CORRUPTED
Program block can not read PX1WRK file.
14411
PX3WRK FILE CORRUPTED
Program block can not read PX3WRK file.
14412
PCM USER PART IS INCORRECT
PCM user part is incorrect.
14413
NOT SUPERVISED
Family is not supervised
14414
ALREADY SUPERVISED
Family is already supervised
14415
OBJECT REFERENCE IN TRIE DIRECTORY IS
INCORRENT
Object referenced in TRIE directory was not found from the
respective collection.
14416
A LOOP WAS DETECTED IN TRIE DIRECTORY
TRIE directory in inconsistent. There is a search path, that
forms a loop.
14417
A QUAD NODE IN TRIE DIRECTORY HAS LESS THAN
TWO CHILDREN
A TRIE directory is inconsistent. There is a quad node, that
has less than two children.
14418
DELETION OF ACCESS CHANNEL IS NOT ALLOWED
Deletion of Access channel is not allowed.
14419
STATE CHANGE OF ACCESS CHANNEL IS NOT
ALLOWED
State change of access channel is not allowed.
14420
MAXIMUM NUMBER OF FAILED COMMANDS
REACHED
Maximum number of failed commands was reached. No
more commands are allowed.
Issue: 30-0
DN987378
643
Error messages
General Error Messages of System
14421
UNKNOWN PLUG-IN UNIT PORT NAME
This error code is generated when
hwi_port_type_by_nam_a_r is given an unknown port
name
14422
UNKNOWN PLUG-IN UNIT PORT TYPE
This error code is generated when
hwi_port_name_by_type_a_r gets an unknown plug-in unit
port type as input parameter
14423
UNKNOWN PLUG-IN UNIT PROPERTY NAME
This error code is generated when
hwi_piu_prop_type_by_nam_a_r gets an unknown plug-in
unit name as input parameter
14424
UNKNOWN PLUG-IN UNIT PROPERTY TYPE
This error code is generated when
hwi_piu_prop_name_by_typ_a_r gets an unknown plug-in
unit property type as input parameter
14425
INCORRECT POOL ID
Id of the abis autoconfiguration pool is incorrect.
14426
INCORRECT ET-PCM
ET-PCM is incorrect.
14427
INCORRECT ET-PCM TIMESLOT
ET-PCM timeslot is incorrect.
14428
INCORRECT POOL SIZE
Size of the abis autoconfiguration pool is incorrect.
14429
ILLEGAL POINTER TO NULL WAS GIVEN
Pointer to null was given in functions input parameter that
is not allowed
14430
PROLOG CONTENT NOT FOUND
Inquired prolog content could not be found.
14431
ROOT ELEMENT NOT FOUND
Content trees root element could not be found
14432
TREES ROOT ELEMENT ALREADY EXISTS
Content tree already has root element
14433
644
MALLOC ERROR HAPPENED
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Malloc could not reserve memory
14434
ILLEGAL CONTENT TYPE
Illegal content type was given as an input parameter to the
function
14435
ILLEGAL ADDED ELEMENT
illegal element was tried to add.
14436
WRONG REPLICATION OR DISTRIBUTION COMMAND
An error used to indicate the not handled nw_tag in NTN.
14437
ILLEGAL ADDED CONTENT
Conten that was tried to add was illegal
14438
ILLEGAL CURRENT CONTENT GIVEN
Current content given to function was illegal
14439
ILLEGAL PARENT CONTENT GIVEN
Parent content given to function was illegal
14440
PREVIOUSLY GIVEN CONTENT ILLEGAL
Content given to function previously was illegal
14441
PREVIOUSLY GIVEN ATTRIBUTE ILLEGAL
Illegal before attribute given to function
14442
FILE NOT FOUND
Given file could not be found
14443
CONTENT NOT FOUND
Inquired content could not be found
14444
ATTRIBUTE NOT FOUND
Inquired attribute could not be found
14445
ILLEGAL SEARCH KEY GIVEN
Illegal search key given to function
14446
FILE COULD NOT BE OPENED
Given file could not be opened
14447
CONTENT TO BE DELETED HAS CHILD
Content that was tried to delete has child
Issue: 30-0
DN987378
645
Error messages
General Error Messages of System
14448
SUBTREE NOT FOUND
Tree did not contain the given subtree
14449
XML PARSING ERROR
Expat could not parse the given XML document. XML
document may contain errors.
14450
CONTENT HAS PARENT OR SIBLING
Content that was tried to delete has parent or sibling
14451
ILLEGAL PARSING MODE GIVEN
Given parsing mode was illegal
14452
PROLOG CONTENT HAS POINTER TO NEXT OR PREV
prolog content tried to be deleted has pointer to next or
previous prolog content
14453
MANDATORY FIELD MISSING FROM THE PDU
This error code is used in TLV PDU decoding procedures
to tell if any mandatory field is missing.
14454
AN EMPTY HOME ADDRESS AREA SLOT WAS FOUND
WITH AN OVERFLOW CHAIN ATTACHED TO IT
This error code is used when manipulating hash_table_t
data structure if home address area is searched and an
empty home address area slot is found with an overflow
chain attached to it. This is actually not an error situation
but the user of hash table should not use the data values
of the element which was returned with this error code but
to continue searching the attached overflow chain, for
example.
14455
ERROR IN DISK UPDATING SUBSYSTEM OF
DATABASE MANAGEMENT SYSTEM
There has been an error in disk updating subsystem of
database management system. The disk updating
subsystem may be out of use for some reason.
14456
NO ACK TO SCDFLE DISTRIBUTION
RUXMAN did not get an acknowledgement in due time
when distributing the SCDFLE data.
14457
ADDRESS NOT AVAILABLE
The address is not available.
14458
EQUIPMENT DATA NOT FOUND
The HMS equipment data is not found.
646
DN987378
Issue: 30-0
General Error Messages of System
14459
Error messages
EQUIPMENT DATA TOO LONG
The HMS equipment data is too long.
14460
TPST UNIT WITH THE GIVEN INDEX ALREADY EXISTS
TPST functional unit already exists in the NTN database.
14461
PCM LINES HAVE ALREADY BEEN DEFINED FOR TPST
The PCM lines for TPST have already been defined in the
database.
14462
TPST PCM LINES ARE NOT FOUND
The PCM lines for TPST are not found in the database.
14463
ALARM DATABASE ACCESS FAILED DURING BCF
RESET
alarm database access failed during BCF reset
14464
THE HOME EXCHANGE OF THE SUBSCRIBER WAS
NOT FOUND FROM THE TXDATA DATABASE
The home exchange of the subscriber was not found from
the TXDATA database.
14465
THE LOCATION OF THE SUBSCRIBER IS UNKNOWN
The location of the subscriber is unknown.
14466
THE PDU IS NOT RECOGNIZED
The PDU tag is not recognized by the process.
14467
PXNETM BUSY
Program block PXNETM is not capable of receiving new
tasks. Try again later.
14468
THE SUBSCRIBER TYPE IS INCORRECT
The subscriber type is incorrect.
14469
TRANSMISSION EQUIPMENT IS OF WRONG KIND
Given transmission equipment is of wrong kind for
requested operation.
14470
EXPAT DID NOT GIVE ERROR CODE
Expat could not give error code. Either error did not
happen or Expat did not have error code to the error.
14471
ILLEGAL ATTRIBUTE WAS TRIED TO DELETE
Attribute that was tried to delete contains pointers to next
attribute,previous attribute or element.
Issue: 30-0
DN987378
647
Error messages
General Error Messages of System
14472
PROLOG CONTENT HAS POINTER TO NEXT OR
PREVIOS
Prolog content can not be deleted. It contains pointers to
next or previous prolog content.
14473
ATTRIBUTE DID NOT CONTAIN POINTER TO ITS
ELEMENT
Attribute did not contain pointer to its element. Attribute
can not be removed from the element.
14475
THE SUBSCRIBER B WAS NOT FOUND IN TXDATA
The subscriber B was not found in the TXDATA database.
14476
UNKNOWN SUBSCRIBER ADDRESS TYPE
The address type of the subscriber is unknown.
14477
ERROR IN THE PARAMETER VALUES
There are errors in the values of the parameters.
14478
PROGRAM PACKAGE IDENTIFIER NOT AVAILABLE
Program package identifier information not available in
requested preprocessor.
14479
RESERVATION OF TERMINAL FUNCTION FAILED
Reservation of terminal function failed during switchover or
restart of programblock.
14480
CONNECTION FAILED IN ACTIVATION OF TERMINAL
FUNCTION
Connection failed during activation of terminal function.
14481
RELEASE OF CONNECTION FAILED IN DEACTIVATION
OF TERMINAL FUNCTION
Release of connection failed during deactivation of
terminal function.
14482
PIU NOT READY
Plug in unit is not ready e.g to receive code from piload
14483
MULTIPLE TONS ARE USED IN THE ANALYSIS TREE
There are multiple types of number used in the analysis
tree.
14485
648
THE DXT IS ALREADY PART OF ANOTHER SUBNET
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The given DXT is either a master or a member in a subnet.
The error happens either when creating a subnet or when
assigning a member DXT to a subnet.
14486
DXT DEFINITION IS NOT FOUND
The given DXT ID is not found in the database.
14488
THE DXT IS EITHER A MASTER IN A SUBNET OR NOT
ASSIGNED
Cannot de-assign a DXT from a subnet, because the DXT
is not a member DXT of the given subnet.
14489
XML DOCUMENT WAS READ TO END
XML document was read to end
14490
GIVEN BUFFER SIZE WAS ILLEGAL
Given buffer size was illegal. Buffer size must be over 0.
14492
CID VALUE DOES NOT EXIST
The given CID value was not found under the given AAL2
type VCLtp.
14493
UTOPIA EXTENDER LIBRARY NOT INITIALIZED
Abstraction library for Utopia Exntender hardware blocks
has not been initialized (with the library initialization
function).
14494
CID VALUE IS ALREADY IN USE
The given CID value is already part of AAL2 crossconnection
14495
PCM BELONGS TO ANOTHER COMPUTER
The PCM is controlled by another computer unit.
14496
LIBRARY CALL WITH INVALID PARAMETER
Utopia Exnterder library function was called with an invalid
parameter (out of range, null etc.).
14497
INVALID OPERATION ON THIS HARDWARE
Current hardware environment does not support this
Utopia Extender library operation (wrong plug-in unit).
14498
NO FREE CID VALUE EXISTS
No free CID values under the given AAL2 type VCLtp
14499
Issue: 30-0
CREATION OF AAL2 CROSS-CONNECTION FAILED
DN987378
649
Error messages
General Error Messages of System
Creation of AAL2 type cross-connection has failed during
the creation sequence
14500
RELOADING OF A2SP UNITS HAS FAILED
Reloading of A2SP units to dynamic ATM routing
structures has failed
14501
THE DEFINED AAL2 CC DOES NOT EXIST
The defined AAL2 cross-connection does not exist
14502
UTOPIA EXTENDER PORT WAS NOT FOUND
Utopia Extender port with the specified Utopia address
was not found.
14503
DESTINATION DXT IS THIS DXT
The destination DXT cannot be the same DXT where the
command is given.
14504
SUBSCRIPTION ALREADY EXISTS
Subscription already exists in subscription list
14505
SUGGESTED RESTART TYPE IS NOT ACCEPTED
Wrong restart type parameter (suggested restart type is
not accepted)
14506
TIME-OUT IN RESTART PHASE 0
Duration of pre boot phase has exceeded its predefined
time.
14507
TIME-OUT IN RESTART PHASE 1
Duration of restart phase 1 (code loading phase) has
exceeded its predefined time.
14508
TIME-OUT IN RESTART PHASE 2
Duration of restart phase 2 (file loading phase) has
exceeded its predefined time.
14509
TIME-OUT IN RESTART PHASE 3
Duration of restart phase 3 (application software starting
phase) has exceeded its predefined time.
14510
NODE REFERENCE IN TRIE DIRECTORY IS INVALID
A pointer in quad node refers to non-existent record of trie
file.
14511
650
ANNOUNCEMENT SENDING WAS UNSUCCESSFUL
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The distributed part of Recovery Event Announcing
Service was unable to send any announcements.
14512
NEWER DATA EXISTS IN THE DATABASE
Timestamp of the given data that was tried to be modified
was older than the timestamp of the same data in the
database. This means that there is already newer version
of the data in the database.
14513
BD-CHANNEL SET ALREADY EXISTS
The given Bd-channel set already exists.
14514
BD-CHANNEL SET DOES NOT EXIST
The given Bd-channel set does not exist.
14515
INVALID EXTENDED CELL RADIUS IN SITE TYPE
MODIFICATION
In site type modification from Nokia 2nd generation to
Nokia Talk-family the maximum extended cell radius
allowed is 35 km.
14516
NASEVA PENDING TABLE IS FULL
Name server pending queue is full.
14517
BACKUP CHANNEL SET DOES NOT EXIST
Backup channel set does not exist.
14518
BACKUP CHANNEL SET IS ALREADY IN USE
The given backup channel set is already in use.
14519
BACKUP CHANNEL SET UNIT TYPE IS INCORRECT
The unit type of given backup channel set is incorrect.
14520
NO FREE RECORDS IN BDDCON FILE
No free records in BDDCON file.
14521
P-CHANNEL ALREADY EXISTS
The given P-channel already exists.
14522
PTFILE FILE IS FULL
PTFILE file is full.
14523
P-CHANNEL DOES NOT EXIST
The given P-channel does not exist.
Issue: 30-0
DN987378
651
Error messages
General Error Messages of System
14525
OPTION MS CAPABILITY INDICATION IS NOT IN USE IN
BSC
Option MS Capability Indication is not in use in the BSC.
14526
OPTION TRACE WINDOW FOR DROPPED CALLS IS
NOT IN USE IN BSC
Option Trace Window for Dropped Calls is not in use in the
BSC.
14527
SUBSCRIPTION NOT FOUND
Subscription not found from subscriber list.
14528
XML DOCUMENT BINARY CONVERSION FAILED
An error has occurred in converting ascii data from XML
document into binary format.
14529
TDSC DISPATCHER STATION CONTROLLER IS NOT IN
WORKING STATE
State of Tetra TDSC dispatcher station controller is not
WO-EX. It is SE-ON or SE-NH or TE or BL.
14530
LEG CREATION FAILED
Failure in leg creation.
14531
MAXIMUM NUMBER OF SIMULTANEOUS ACTIONS
EXCEEDED
The maximum number of simultaneous actions is
exceeded.
14532
FILE READING FAILED
This error message is used when reading of the TBS
software management file failed.
14533
FILE WRITING FAILED
Writing to the TBS software management file failed.
14534
PACKAGE_ID ALREADY EXIST
This error message is used if you are trying to create an
already existing package_id. Try another package_id.
14535
PACKAGE DIRECTORY DOES NOT EXIST
The package directory that does not exist is referred to.
Make a directory or change it.
14536
READING MASTER FILE FAILED
Reading the master file is failed.
652
DN987378
Issue: 30-0
General Error Messages of System
14537
Error messages
FILE SIZES ARE DIFFERENT
The size of the physical files does not correspond to the
one that has been informed in the master file. Copy files
again to the disks of DXT.
14538
AF DOES NOT EXIST
If the application file(s) is not found from the disks of DXT
or if the version of the application file(s) is wrong, copy files
again to the disks of DXT.
14539
MASTER FILE DOES NOT EXIST
The master file is not found from other or on both disks of
DXT. Copy files again to the disks of DXT.
14540
MASTER FILE IS ALREADY IN USE
The master file which belongs to the package has already
been created.
14541
DIFFERENT MF:S ON DISKS OF DXT
The master files do not correspond to each other on disks
of DXT. Copy the files again to the disks of DXT.
14542
PACKAGE_ID DOES NOT EXIST
The given package_id is not found.
14543
DEFAULT SOFTWARE
The given package_id is defined as default package.
Activate some other package to the TBS.
14544
BACKUP SOFTWARE
The given package_id is defined as backup package.
Define new backup package or clear the backup package
information.
14545
PHYSICAL FILES NOT DELETED
The physical files are not deleted from disks of DXT. Use
disk handling commands to delete physical files.
14546
BASE STATION DOES NOT EXIST
The given base station is not found in the database.
14547
NO RESOURCES
There is already an operation ongoing in the given TBS.
14548
ACTIVE OPERATION
The requested operation has already been executed.
Issue: 30-0
DN987378
653
Error messages
General Error Messages of System
14549
BASE STATION DOES NOT RESPOND
The given base station does not respond.
14550
DEFAULT INFO MISSING
The base station does not know which package is default.
14551
NO FLASH MEMORY
The flash memory of TBC is faulty or totally missing.
14552
LEG ALREADY EXISTS
Leg has already created.
14553
FILE TRANSFER FAILURE
Transferring of files to the RAM memory of TBC failed.
14554
LEG RELEASE FAILED
Leg release failed.
14555
FILE SAVING FAILURE
Saving files to the flash memory of TBC or rTBC failed.
14556
LEG DOES NOT EXIST
Leg does not exist.
14557
LEG CONNECT FAILED
Leg connection failed.
14558
LEG ALREADY CONNECTED
Leg is already connected.
14559
LEG DISCONNECT FAILED
Leg disconnection failed.
14560
LEG REFRESH FAILED
Leg refresh failed.
14561
LEG MODIFY FAILED
Leg modification failed.
14562
PACKAGE NOT ATTACHED
The given package has not been attached to the given
TBS. Attach the package first.
14563
654
TTRX-<TBS NUMBER>-<TTRX INDEX> DOES NOT
EXIST
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The TTRX-<TBS number>-<TTRX index> is not found.
14564
PACKAGE ALREADY EXISTS
The package already exists in the TBS.
14565
LEG MODIFY NOT RESTORED
Leg modification not restored.
14566
NO RIGHTS TO SERVICE TERMINAL SESSION
User has no rights to execute DDS command, therefore he
has no rights to service terminal session.
14567
GIVEN NUMERICAL USER ID IS TOO SMALL
Enalib is unable to create user ID, because numerical user
ID is too small.
14568
GIVEN NUMERICAL USER ID IS TOO BIG
Enalib is unable to create user ID, because numerical user
ID is too big.
14569
B SERIES HWILIB ROUTINE
B series routine of HWILIB, that cannot be used in A
series.
14570
PLUG-IN UNIT PORT ALREADY EXISTS
The port of plug-in unit already exists in equipment
database and thus it cannot be created again.
14571
IMA GROUP DOES NOT EXIST
The given identifier is not assigned to any existing IMA
Group.
14572
IMA GROUP ID ALREADY EXISTS
The given identifier is already assigned to another IMA
Group. Repeat the command with a suitable value or let
the system select a free one.
14573
ATM INTERFACE EXISTS
The operation could not be performed because there is an
ATM interface related to the specified IMA Group.
14574
EXCHANGE TERMINAL ALREADY IN USE
At least one of the specified Exchange Terminals is already
related to an IMA group or to an ATM interface. Check the
existing Exchange Terminals and repeat the command with
suitable values or release the Exchange Terminal if
desired.
Issue: 30-0
DN987378
655
Error messages
General Error Messages of System
14575
THE EXCHANGE TERMINAL IS NOT IN THE IMA
GROUP
The Exchange Terminal is not related to the IMA Group.
Check the existing Exchange Terminals of the IMA Group
and repeat the command with suitable values if desired.
14576
THE EXCHANGE TERMINAL IS THE TIMING
REFERENCE LINK
The operation could not be performed because the
Exchange Terminal is defined to be the Timing Reference
Link of the IMA group. The existence of the Timing
Reference Link is essential for each IMA group. Check the
existing Exchange Terminals of the IMA Group and repeat
the command with suitable values if desired.
14577
IMA GROUP DATA INCONSISTENT IN THE SYSTEM
An error occurred during the command execution.
Corrective actions could not restore the consistency of the
databases.
14578
ENDPOINT GROUP DOES NOT EXIST
The given identifier is not assigned to any endpoint group
under the specified route.
14579
ENDPOINT GROUP ID ALREADY EXISTS
The given identifier is already assigned to another
endpoint group under the specified route. Repeat the
command with a suitable value or let the system select a
free one.
14580
ENDPOINT GROUP WITH DEFINED SERVICE
CATEGORIES ALREADY EXISTS
An endpoint group with the service categories defined
already exists under the specified route. Use the existing
endpoint group if suitable or repeat the command with
different values.
14581
ENDPOINT GROUP DATA INCONSISTENT IN THE
SYSTEM
An error occurred during the command execution.
Corrective actions could not restore the consistency of the
databases.
14582
THE ROUTE IS NOT AN EXTERNAL ATM ROUTE
The specified route is not suitable for the use of ATM
channel selection. Check the parameters of the routes and
repeat the command with a suitable route.
656
DN987378
Issue: 30-0
General Error Messages of System
14583
Error messages
AAL2 PATH DOES NOT EXIST
The given identifier is not assigned to any endpoint under
the specified route.
14584
AAL2 PATH ID ALREADY EXISTS
The given identifier is already assigned to another
endpoint under the specified route. Repeat the command
with a suitable value.
14585
ENDPOINT EXISTS
The operation could not be performed because there are
endpoint(s) under the specified endpoint group. If desired,
delete the endpoints and repeat the command.
14586
ENDPOINT DATA INCONSISTENT IN THE SYSTEM
An error occurred during the command execution.
Corrective actions could not restore the consistency of the
databases.
14587
ENDPOINT GROUP WITH DEFINED SERVICE
CATEGORIES DOES NOT EXIST
There is no endpoint group with the defined service
categories under the specified route. Create a new
endpoint group with suitable parameters if desired and
repeat the command.
14588
ENDPOINT BLOCKING SITUATION IS ONLY PARTLY
UPDATED
The blocking situation of the endpoint is only partly
updated to the system. Some part of the system rejected
the service request and the use of the specified endpoint
might be prevented. This failure does not affects to the
other endpoints or to the other parts of the system and the
new data is also updated to the failed part in request or
after restart.
14589
VPLTP USAGES DO NOT ALLOW THE CREATION OF
PERMANENT VCLTPS
None of the usages defined for the VPLtp allows the
creation of a permanent VCLtp under this VPLtp. Compare
the usages of the VPLtp with the usage you need the
VCLtp and give the command again using a VPLtp with the
usage you intend or redefine the usages of the VPLtp.
14590
Issue: 30-0
VPLTP USAGES DO NOT ALLOW THE CREATION OF
TEMPORARY VCLTPS
DN987378
657
Error messages
General Error Messages of System
None of the usages defined for the VPLtp allows the
creation of a temporary VCLtp under the VPLtp. Compare
the usages of the VPLtp with the usage you need the
VCLtp and give the command again using a VPLtp with the
usage you intend or redefine the usages of the VPLtp.
14591
THE USAGE IS NOT ALLOWED FOR VPLTP
The specified usage can not be defined for VPLtps with
service level VP. Check the behaviour of the usage.
14592
USAGE IS NOT ALLOWED FOR PERMANENT
TERMINATION POINTS
The specified usage can not be defined for permanent
termination points. Check the behaviour of the usage.
14593
THE USAGE IS NOT ALLOWED FOR TEMPORARY
TERMINATION POINTS
The specified usage can not be defined for temporary
termination points. Check the behaviour of the usage.
14594
THE USAGE IS NOT DEFINED FOR THIS VPLTP
The specified usage is not defined in the set of usages of
this VPLtp. Check the usages defined for the VPLtp and
redefine the set if desired.
14595
ONE OF THE USAGES REQUESTS NON-SHARED USE
OF THE WHOLE VPLTP
The set of usages defined for the VPLtp is not allowed. At
least one of the usages request non-shared use of the
whole VPLtp so it can not be in a set with others. Check
the behaviours of specified usages and redefine the set of
usages.
14596
THE USAGE OF THE TERMINATION POINT DOES NOT
ALLOW MODIFICATIONS
The specified termination point is in use and the usage
does not allow a modification. Check the behaviour of the
usage and free the termination point if desired.
14597
THE USAGE OF THE TERMINATION POINT DOES NOT
ALLOW SHUTTING DOWN
The specified termination point is in use and the usage
does not allow shutting down. Check the behaviour of the
usage.
14598
658
THE USAGE OF THE TERMINATION POINT DOES NOT
ALLOW LOCKING
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The specified termination point is in use and the usage
does not allow locking. Check the behaviour of the usage
and free the termination point if desired.
14599
THE TERMINATION POINT IS IN USE
The specified termination point is in use and the operation
can not be performed. If desired, free the termination point
and repeat the command.
14600
NO ISDN PCMS FOUND FOR THE CONN.GROUP
No ISDN PCMs related to this connection group are found
from the database.
14601
ILLEGAL RANGE
The number range which was attempted to insert into the
DB was illegal.
14602
OVERLAPPING RANGE
The attempted range is overlapping with some existing
range.
14603
RANGE IS NOT FOUND IN DB
The range is not found in the database.
14604
NUMBER IS NOT FOUND IN DB
The searched number is not found in the database.
14605
NUMBER ALREADY EXISTS
The number to be inserted already exists.
14606
ROUTING INFO IS NOT FOUND
The routing info for some number or range is not found.
14607
CONNECTION EXIST
Creation done to connection which already exists.
14608
THE CONNECTION DOES NOT EXIST
The action cannot be performed because the connection
needed for it does not exist.
14609
ADDRESS EXIST
Creation is done to an address which already exists.
14610
ADDRESS NOT EXIST
Action is done to an address which does not exist.
Issue: 30-0
DN987378
659
Error messages
General Error Messages of System
14611
AAL2 SIGNALLING SERVICE UNAVAILABLE
Requested service cannot be activated due to the lack of
resources. The service provider is not ready to perform the
requested service. Check the system configuration and/or
try again later.
14612
USAGE NOT AVAILABLE
Usage not available in the current software packet.
14613
THE NEW SET OF USAGES LACKS AN ALREADY
ASSIGNED USAGES
There is at least one VCLtp assigned with one of the
usages not defined in the new set of usages. Compare the
new and existing set of usages and redefine the new set or
free the reserved VCLtp if desired.
14614
ONE OF THE USAGES IN NOT FOR SERVICE LEVEL
VC
At least one of the usages in the set can not be assigned
to any VCLtp.Check the behaviours of the defined usages
and redefine the set.
14615
FUNCTIONAL UNIT IS IN RESTART AND RESTART
PROCEEDS NORMALLY.
Functional unit is restarting and restart proceeds normally.
14616
GIVEN TCN IS CONNECTED TO ANALYSIS
Given time control number is connected to analysis
14617
GIVEN TCN ALREADY EXISTS
Given time control number already exists.
14618
PENDING REQUEST ADDED SUCCEFULLY TO
PENDING TABLE.
Pending request added successful to pending table.
14619
DATABASE HAS NO REMOTE COPY
The user has tried to handle database remote copy, but the
database has no remote copy.
14620
TIME-OUT VALUE EXCEEDED FOR AAL TYPE 2 BLOCK
OR UNBLOCK OPERATION
The peer signalling entity at the remote AAL type 2
Network Element didnot confirm the requested blocking or
unblocking operation. Try again with checked parameters
to be sure that operation is successfully completed.
660
DN987378
Issue: 30-0
General Error Messages of System
14621
Error messages
TIME-OUT VALUE EXCEEDED FOR AAL TYPE 2 RESET
The peer signalling entity at the remote AAL type 2
Network Element didnot confirmed the requested AAL type
2 reset operation. See the related alarm information for
further actions.
14622
COMMAND CAN NOT BE APPLIED ON THIS DATABASE
Command cannot be applied on this database
14623
LOGICAL TERMINAL NUMBER CONFLICT IN FILES
The same logical terminal number is reserved for more
than one channel in files.
14624
VCC WAS RESERVED, ALTHOUGH IT WAS ALREADY
RESERVED TO SAME FAMILY
The VCC specified in this message was reserved,
although it was reserved to another process which belongs
to my process family.
14625
VCC WAS RE-RESERVED
The VCC specified in this message was reserved,
although it was already reserved to me. In other words, the
VCC is re-reserved to me.
14626
VCC WAS RELEASED, ALTHOUGH IT WAS RESERVED
BY OTHER PROCESS OF SAME FAMILY
The VCC specified in this message was released, although
it was reserved to another process which belongs to my
process family.
14627
AN UNKNOWN ERROR HAPPENED WHILE RELEASING
The VCC specified in this message was not released,
because an unknown error happened while releasing it.
14628
REMOTE COPY INFORMATION NOT AVAILABLE
Database remote copy information is not available.
14629
INVALID INTERNAL ATM ROUTE USE
Given invalid value where internal ATM route is used for.
14630
TOO MANY ROUTES TO SIGNALLING POINT
There is already the maximum number of routes
connected to same signalling point.
14631
Issue: 30-0
SGSN IS NOT UPDATED. PCU UNIT COMMUNICATION
FAILED. BVC MAY BE ACTIVE IN SGSN
DN987378
661
Error messages
General Error Messages of System
SGSN is not updated because the PCU unit did not
respond. It is possible that BVC exists in active state in
SGSN. Radio network database is updated.
14632
SGSN IS NOT UPDATED, PCU UNIT COMMUNICATION
FAILURE.
Operation was partly successful, SGSN did not receive the
request. Radio network database is updated.
14633
ROUTE LINKED TO SUBDESTINATION
Route must not be deleted if it is linked to some
subdestination.
14634
ROUTE HAS VPC/VCC ENDPOINT GROUPS LINKED TO
IT
Route must not be deleted if it has VPC/VCC endpoint
groups linked to it.
14635
PRE-DETERMINED CROSS-CONNECTION
Pre-determined connection cannot be modified or deleted
14636
INTERNAL INTERFACE ID DOES NOT EXIST
Internal interface id does not exist for functional unit.
14637
XCONN PATH IS NOT READY
PIGPRB is still collecting info or a FU had been deleted on
the path.
14638
PARTNER CHANNEL SET IS ALREADY IN USE
The given partner channel set is already in use.
14639
PARTNER CHANNEL SET DOES NOT EXIST
Partner channel set does not exist.
14640
PARTNER CHANNEL SET UNIT TYPE IS INCORRECT
The unit type of the given partner channel set is incorrect.
14641
BACKUP CHANNEL SET DOES NOT SUPPORT
SUBSCRIBERS
The given backup channel set does not support
subscribers.
14642
PARTNER CHANNEL SET SUPPORTS SUBSCRIBERS
The given partner channel set supports subscribers.
14643
662
MISMATCH OF CHANNEL NUMBERS OF PARTNERS
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Channel numbers of partners do not match.
14644
DELETION OF ALL BD-CHANNELS NOT ALLOWED
Deletion of all Bd-channels is not allowed.
14645
PCM-TSL NOT FOUND
The PCM-TSL is not found.
14646
PCU-LAPF NOT FOUND
The PCU-LAPF is not found.
14647
PCU-LAPF RESERVED
The PCU-LAPF is already reserved.
14648
ILLEGAL STATE
The state change of unit is not allowed. New state is
illegal.
14649
ILLEGAL STATUS
The status change is not allowed. The status is not
settable or clearable by the user.
14650
NOT A HOT STANDBY UNIT
Controlled switchover is not possible. The spare unit is not
a hot standby.
14651
UNIT IS NOT A STANDBY UNIT
Controlled switchover is not allowed. Unit is not a standby
unit.
14652
CAUSES SYSTEM RESTART
Unit restart is not allowed. It causes restart of whole
system.
14653
UNIT IS NOT RESTARTABLE
The restart of unit is not possible. Unit is not restartable.
14654
MAXIMUM AMOUNT OF TRX LINKS IN USE
Maximum number of TRX links per BCSU in use.
14655
INTERNAL INFO TABLE OF DD1MAN IS FULL
The table containing information about DD2MAN families
is full.
14656
Issue: 30-0
NO FREE FAMILY ID FOR DD2MAN FAMILY
DN987378
663
Error messages
General Error Messages of System
There are no free family id:s in the pool of family id:s for
dd2man families.
14657
DD1MAN WAITING FOR SPARE UNIT STATE TO
CHANGE
DD1MAN is waiting for the spare unit to get out of the SPUP state in order to be able to start DD2MAN family.
14658
UNIT STATE MUST BE WO BECAUSE IT HAS FRAME
RELAY RESOURCES TO SUPERVISE
The working state of the unit must be active (WO) because
it has frame relay resources to supervise.
14659
UNIT STATE MUST BE SP BECAUSE IT HAS NO FRAME
RELAY RESOURCES TO SUPERVISE
The working state of the unit must be passive (SP)
because it has no frame relay resources to supervise.
14660
FAILURE IN SECMO PLUG-IN UNIT
A service has failed due to an error in the SECMO plug-in
unit.
14661
LOCKING OF OBJECT ALLOWED ONLY WITH FORCED
LOCK.
The locking of object is allowed only when forced lock is
used.
14662
DATABASE SYSTEM PROGRAM BLOCK DENIES
SWITCHOVER
The database system program block denies switchover.
14663
THE FRAME TO BE CIPHERED OR DECIPHERED IS
TOO LONG
Frame length is greater than the maximum supported
value.
14664
REQUESTED CIPHERING ALGORITHM NOT
SUPPORTED
The ciphering algorithm requested by the application is not
supported by the ciphering device or the driver currently in
use.
14665
INVALID PCU BCSU LOGICAL ADDRESS
Invalid logical address of the host BCSU of PCU.
14666
INVALID PCU INDEX
Invalid PCU index.
664
DN987378
Issue: 30-0
General Error Messages of System
14667
Error messages
ACCESS SERVER EXISTS
The specified access server exists.
14668
ACCESS SERVER NONEXISTENT
The specified access server does not exists.
14669
MULTIPOOL ACCESS SERVER DOES NOT EXIST
Specified multi-pool Access Server does not exist.
14670
RESOURCE CONNECTED TO ACCESS SERVER
Specified resource is already connected to Access Server.
14671
RESOURCE NOT CONNECTED TO ACCESS SERVER
Specified resource is not connected to the access server.
14672
RESOURCE RESERVED
Specified resource is reserved.
14673
IP PARAMETERS NOT FOUND
Attempt to modify parameters that are not created.
14674
MISSING L2TP PARAMETERS
L2TP parameters are not specified.
14675
IP ADDRESS ALREADY EXISTS
The IP address already exists.
14676
MISSING VPN TUNNEL PARAMETERS
VPN tunnel parameters are not specified.
14677
IP ADDRESS NOT FOUND
IP address is not found.
14678
IP TERMINAL DATA DOES NOT EXIST
IP terminal data does not exist.
14679
QUASI ASSOCIATED PCM ALREADY EXISTS
Quasi associated PCM already exists.
14680
QUASI PCM NOT FOUND
Quasi associated PCM is not found.
14681
IP TERMINAL DATA EXISTS
IP terminal data exists.
Issue: 30-0
DN987378
665
Error messages
General Error Messages of System
14682
RAS NAME ALREADY EXIST
The name of signalling control already exists.
14683
RAS NAME NOT FOUND
The name of signalling control is not found.
14685
IMA GROUP ALREADY IN USE
The specified IMA Group is already related to an ATM
interface. Create a new IMA Group if needed and repeat
the command with a free IMA group.
14686
DIFFERENT BACKUP PACKAGE
There is a defined different backup package in the given
TBS.
14687
NS-VC CONNECTION IS UNAVAILABLE
The Bearer channel or the DLCI is blocked in Gb interface.
The system activates the connection when the Bearer and
DLCI are available again.
14688
INCORRECT COUNT VALUE
The counter value is incorrect.
14689
EF ALLOCATION ERROR
Event Forwarding Service fails in buffer allocation.
14690
TERMINAL ALREADY EXISTS IN THE DATABASE
Terminal already exists in the subscriber database.
14691
TERMINAL DOES NOT EXIST IN THE DATABSE
Terminal does not exist in the subscriber database.
14692
EXTERNAL PCM ALREADY EXISTS
External PCM already exists for S30 in the database.
14693
AAL TYPE 2 PATH IS BLOCKED
AAL type 2 path is blocked.
14694
VP/VC SELECTION COULD NOT BE UPDATED
The request was successful except for the update to
VP/VC selection. If the modified object is irrelevant for
VP/VC selection, this error can be ignored. If the object or
objects thereunder are subject to VP/VC selection, the
system will still work but the specific endpoints are never
used.
666
DN987378
Issue: 30-0
General Error Messages of System
14695
Error messages
FORBIDDEN: NOT IN HOME LOCATION
This error code appears if a request to modify some
Packet Data-related object reaches a location that is not
the home DXT.
14696
RAILIB CALL IS NOT ALLOWED IN UNIT
An attempt was made to call the RAILIB library in a unit
where it is not allowed.
14697
WCEL OBJECT STATE CHANGE IS REJECTED DURING
DATABASE COPY
An attempt was made to change the sate of the WCEL
object during database copying when it is not allowed.
14698
MAXIMUM NUMBER OF NCID VCC ENDPOINTS HAS
BEEN REACHED
The maximum number of NCID VCC endpoints has been
reached.
14699
VCC CELL RATE OUT OF ALLOWABLE RANGE
VCC cell rate is out of the allowable range.
14700
AN INCONSISTENCY SITUATION HAS BEEN DETECED
IN CAC
An inconsistency situation has been detected in CAC.
14701
INITIALIZATION NOT READY
Initialization concerning the given task in a functional unit
is not yet ready
14702
MCC OR MNC IS NOT CONFIGURED.
MCC (Mobile Country Code) or MNC (Mobile Network
Code) is not configured to the system.
14703
HMS OPERATION INTERRUPTED
The requested HMS operation was interrupted.
14704
INVALID HMS MESSAGE LENGTH
The HMS message length is invalid.
14705
NO FREE TIC NUMBERS
No free tic numbers in the subscriber database to be
reserved.
14706
Issue: 30-0
ILLEGAL TIC NUMBER
DN987378
667
Error messages
General Error Messages of System
The operator is trying to delete a non-existing tic number
from the subscriber database.
14707
VCC RESERVATION FAILURE
Virtual channel connection could not be reserved by
AAPSEB.
14708
WRONG VCC RESERVATION ATTRIBUTE
Virtual channel connection (VCC) could not be reserved
because one of VCC attributes is illegal
14709
TERMINAL HAS CONNECTION TO X25 ADDRESS SET
Operation cannot be done because the terminal is
connected to X25 address set. Connection must be
deleted before this operation.
14710
DATABASE REMOTE COPY INITIALIZATION FAILED
Database remote copy initialization failed.
14711
NO MORE DATABASE REMOTE COPY CONNECTIONS
No more database remote copy connections.
14712
DATABASE REMOTE COPY SERVER NOT INITIALIZED
Database remote copy server is not initialized.
14713
DATABASE REMOTE COPY SERVER DOES NOT
ANSWER
Database remote copy server does not answer.
14714
DATABASE REMOTE COPY LOADING FAILED
Database remote copy loading failed.
14715
DATABASE REMOTE COPY FILE DUMPING FAILED
Database remote copy file dumping failed.
14716
RNC NOT FOUND
The Radio Network Controller (RNC) object cannot be
found in radio network database.
14717
WBTS NOT FOUND
The Base Station (WBTS) object can not be found in radio
network database.
14718
WCEL NOT FOUND
The cell (WCEL) object cannot be found in radio network
database.
668
DN987378
Issue: 30-0
General Error Messages of System
14719
Error messages
COCO NOT FOUND
The Connection Configuration (COCO) object cannot be
found in radio network database.
14722
DATABASE REMOTE COPY CONNECTION CLOSED
Database remote copy connection is closed.
14723
DATABASE REMOTE COPY DUMP FAILED
Database remote copy dump failed.
14724
DATABASE REMOTE COPY PREVENT FAILED
The database remote copy prevent failed.
14725
DATABASE REMOTE COPY RESUME FAILED
The database remote copy resume failed.
14726
DATABASE REMOTE COPY STATE IS FALSE
The database remote copy state is false.
14727
HMALAR IS BUSY
HMALAR is busy.
14728
RNC ALREADY CREATED
The Radio Network Controller (RNC) object is already
created in radio network database.
14729
DATABASE REMOTE COPY LOADING DONE
SUCCESSFULLY
Database remote copy loading was done successfully.
14730
WBTS ALREADY CREATED
The Base Station (WBTS) object is already created in
radio network database.
14731
WCEL ALREADY CREATED
The Cell (WCEL) object is already created in radio network
database.
14732
COCO ALREADY CREATED
The Connection Configuration (COCO) object is already
created in radio network database.
14733
RACH NOT FOUND
The Random Access Channel (RACH) object cannot be
found in radio network database.
Issue: 30-0
DN987378
669
Error messages
General Error Messages of System
14734
FACH NOT FOUND
The Forward Access Channel (FACH) object can not be
found in radio network database.
14735
MAXIMUM OF WCELS UNDER WBTS
There is no room for a new cell (WCEL) under this Base
Station (WBTS).
14736
DATABASE REMOTE COPY TIMER IS NOT CORRECT
Database remote copy timer is not correct.
14737
ADJS NOT FOUND
The Intra Frequency Adjacency (ADJS) object cannot be
found in radio network database.
14738
ADJI NOT FOUND
The Inter Frequency Adjacency (ADJI) object cannot be
found in radio network database.
14739
ADJG NOT FOUND
The GSM Adjacency (ADJG) object cannot be found in
radio network database.
14740
FMCS NOT FOUND
The Intra Frequency Measurement Control (FMCS) object
cannot be found in radio network database.
14741
FMCI NOT FOUND
The Inter Frequency Measurement Control (FMCI) object
cannot be found in radio network database.
14742
FMCG NOT FOUND
The GSM Frequency Measurement Control (FMCG) object
cannot be found in radio network database.
14743
HOPS NOT FOUND
The Intra Frequency Handover Path (HOPS) object cannot
be found in radio network database.
14744
HOPI NOT FOUND
The Inter Frequency Handover Path (HOPI) object cannot
be found in radio network database.
14745
HOPG NOT FOUND
The GSM Handover Path (HOPG) object cannot be found
in radio network database.
670
DN987378
Issue: 30-0
General Error Messages of System
14746
Error messages
FMCS ALREADY CREATED
An Intra Frequency Measurement Control (FMCS) object
with the given identity is already created in radio network
database.
14747
FMCI ALREADY CREATED
An Inter Frequency Measurement Control (FMCI) object
with the given identity is already created in radio network
database.
14748
FMCG ALREADY CREATED
A GSM Measurement Control (FMCG) object with the
given identity is already created in radio network database.
14749
HOPS ALREADY CREATED
An Intra Frequency Handover Path (HOPS) object with the
given identity is already created in radio network database.
14750
HOPI ALREADY CREATED
An Inter Frequency Handover Path (HOPI) object with the
given identity is already created in radio network database.
14751
HOPG ALREADY CREATED
A GSM Handover Path (HOPG) object with the given
identity is already created in radio network database.
14752
ADJS COLLECTION FULL
There is no room for a new Intra Frequency Adjacency
(ADJS) object in radio network database.
14753
ADJI COLLECTION FULL
There is no room for a new Inter Frequency Adjacency
(ADJI) object in radio network database.
14754
ADJG COLLECTION FULL
There is no room for a new GSM Adjacency (ADJG) object
in radio network database.
14755
FMCS COLLECTION FULL
There is no room for a new Intra Frequency Measurement
Control (FMCS) object in radio network database.
14756
FMCI COLLECTION FULL
There is no room for a new Inter Frequency Measurement
Control (FMCI) object in radio network database.
14757
Issue: 30-0
FMCG COLLECTION FULL
DN987378
671
Error messages
General Error Messages of System
There is no room for a new GSM Frequency Measurement
Control (FMCG) object in radio network database.
14758
HOPS COLLECTION FULL
There is no room for a new Intra Frequency Handover
Path (HOPS) object in radio network database.
14759
HOPI COLLECTION FULL
There is no room for a new Inter Frequency Handover
Path (HOPI) object in radio network database.
14760
HOPG COLLECTION FULL
There is no room for a new GSM Handover Path (HOPG)
object in radio network database.
14761
WCEL COLLECTION FULL
There is no room for a new Cell (WCEL) object in radio
network database.
14762
COCO COLLECTION FULL
There is no room for a new Connection Configuration
(COCO) object in radio network database.
14763
RACH COLLECTION FULL
There is no room for a new Random Access Channel
(RACH) object in radio network database.
14764
FACH COLLECTION FULL
There is no room for a new Forward Access Channel
(FACH) object in radio network database.
14765
MAXIMUM OF ADJSS FOR WCEL
The maximum of Intra Frequency Adjacency (ADJS) object
relations for the Cell (WCEL) object is reached.
14766
MAXIMUM OF ADJIS FOR WCEL
The maximum of Inter Frequency Adjacency (ADJI) object
relations for the Cell (WCEL) object is reached.
14767
MAXIMUM OF ADJGS FOR WCEL
The maximum of GSM Adjacency (ADJG) object relations
for the Cell (WCEL) object is reached.
14768
COCO AND WBTS ALREADY RELATED
The relation between the Connection Configuration
(COCO) object and Base Station (WBTS) object already
exists.
672
DN987378
Issue: 30-0
General Error Messages of System
14769
Error messages
NO RELATION BETWEEN COCO AND WBTS
No relation between the Connection Configuration (COCO)
object and the Base Station (WBTS) object exists.
14770
UNKNOWN PID OWNER
The value of the pid owner parameter is unknown to radio
network database.
14771
NO COCO DEFINED FOR WBTS
The identity of the used Connection Configuration (COCO)
object is not defined in Base Station (WBTS) parameters.
14772
ILLEGAL TARGET SUBDATABASE
The used transaction or fastread is directed to an unknown
or illegal subdatabase of RAQUEL.
14773
CONNECTION IS NOT IN LOCKED STATE
The specified operation requires the connection to be in
locked administrative state. In case of a ptm connection
the operations related only to one branch requires the
specified branch or the whole connection to be in locked
administrative state.
14776
FILE NOT FOUND FROM SOURCE MAFILE
File is missing from source mafile.
14777
HARDWARE CAPACITY IS NOT SUFFICIENT
Hardware capacity is not sufficient for the interface
bandwidth. Check the capacity of the ET or the IMA Group
related to the interface and try again with a suitable
bandwidth value. In the case of removing an ET from an
IMA Group: check the bandwidth specified for the
interface. Decrease the bandwidth, if desired, by modifying
the Access Profile related to the interface and try again.
14778
HMS TARGET DOES NOT EXIST
The target does not exist in the HMS.
14779
THERE ARE NO FREE RESOURCES FOR REQUESTED
SERVICE
Requested service cannot be performed because there are
no free resources.
14780
ERROR IN READING OR WRITING A DISK FILE
A file in a hard disk is corrupted or the file system services
failed somehow. Check the system logs to find the possible
cause.
Issue: 30-0
DN987378
673
Error messages
General Error Messages of System
14781
MAXIMUM NUMBER OF FAILED PROGRAM BLOCKS
REACHED
Maximum number of program blocks have failed during
program block failure supervision period.
14782
PROGRAM BLOCK IS NOT RESTARTABLE
Restarting of the program block was denied by starter
software.
14783
HOT DATA IP CONNECTION FAILED
HBSAVE can not get connection to post-processing
system.
14784
HOT DATA IP CONNECTION LOST
HBSAVE lost connection to post-processing system.
14785
CAPACITY LIMIT EXCEEDED
The master process discards the get routing info request
because there is no capacity available due to the limitation.
14786
BTS SOFTWARE DOES NOT SUPPORT GPRS
GPRS cannot be enabled in this BTS because the BTS
software build has no GPRS capability.
14788
ILLEGAL QUERY DATA
AAPSEB has received illegal data in query request.
14789
QUERY OF FREE VCC
AAPSEB has received a query request concerning a free
VCC.
14790
NO SUITABLE CLUSTER WAS FOUND FOR THE
COMPUTER
TOMPRB could not find a suitable cluster where the
computer could be placed.
14791
COMPUTER ALREADY EXISTS IN THE MESSAGE
CONNECTION NETWORK
The computer to be added is already in the message
connection network.
14792
CALL ROUTE FOR THIS DXT STILL EXISTS IN
ROUTING TABLE
The DXT definition cannot be deleted, because the call
route still exists in the routing table.
14793
674
DATABASE WARM UP LIBRARY PARAMETER ERROR
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The database warm up library has been called with
erroneous parameters.
14794
NO ANSWER TO WARM UP REQUEST
The database warm up library has not received an answer
to its warm up request.
14795
FILE LOADING FAILED IN DATABASE WARM UP
File loading has failed during database warm up.
14796
DATABASE WARM UP LIBRARY NOT INITIALIZED
Some application programs have tried to use the database
warm up library services, but the database warm up library
is not initialized.
14797
TIMER CONFLICT IN DATABASE WARM UP LIBRARY
An incorrect timer identification value has been passed to
the database warm up library.
14798
DATABASE WARM UP LIBRARY IS IN ILLEGAL STATE
The database warm up library is in illegal state. Database
warm up has failed.
14799
DATABASE WARM UP LIBRARY IS IN ILLEGAL SUB
STATE
The database warm up library is in illegal sub state.
Database warm up has failed.
14800
DATABASE WARM UP SYNCHRONIZATION FAILED
The database warm up failed in the process
synchronization step.
14801
DXT ID IS NOT IDENTICAL WITH THE PREDEFINED CNUMBER IN APPARA FILE
The given exchange identifier differs from the C-number in
the general parameter module (APPARA).
14802
INVALID FILE SYSTEM
The requested file system is not supported by the device in
question.
14803
UNKNOWN FILE SYSTEM
The file system used on the device is unknown.
14804
GIVEN LOCATION AREA IDENTIFICATION NOT WITHIN
LIMITS
Given location area identification not within limits.
Issue: 30-0
DN987378
675
Error messages
General Error Messages of System
14805
ILLEGAL ET COMBINATION
One or more ETs in the group are invalid. If the IMA group
is in question, ETs may be in separate network interface
units or ET(s) may already belong to another interface.
14806
NUMBER OF G4WIFS EXCEEDS MAXIMUM AMOUNT IN
CREATING NEW SUBSCRIBER INTO THSDAT DB
The number of G4WIFS exceeds maximum amount in
creating new subscriber into THSDAT DB.
14807
NUMBER OF MSISDNS EXCEEDS MAXIMUM AMOUNT
IN CREATING NEW SUBSCRIBER INTO THSDAT DB
The number of MSISDNS exceeds maximum amount in
creating new subscriber into THSDAT DB.
14808
NUMBER OF FSSNS EXCEEDS MAXIMUM AMOUNT IN
CREATING NEW SUBSCRIBER INTO THSDAT DB
The number of FSSNS exceeds maximum amount in
creating new subscriber into THSDAT DB.
14809
NUMBER OF CONN_GROUPS EXCEEDS MAXIMUM
AMOUNT IN CREATING NEW SUBSCRIBER INTO
THSDAT DB
The number of CONN_GROUPS exceeds maximum
amount in creating new subscriber into THSDAT DB.
14810
NUMBER OF STATIC_ADDRS EXCEEDS MAXIMUM
AMOUNT IN CREATING NEW SUBSCRIBER INTO
THSDAT DB
The mumber of STATIC_ADDRS exceeds maximum
amount in creating new subscriber into THSDAT DB.
14811
NUMBER OF SUBS_GROUPS EXCEED MAXIMUM
AMOUNT IN CREATING NEW SUBSCRIBER INTO
THSDAT DB
The number of SUBS_GROUPS exceeds maximum
amount in creating new subscriber into THSDAT DB.
14812
SPECIFIED ROUTER IS NOT CONFIGURED.
The router cannot be found in the file /etc/iprou.dat. If you
need this router, you must first add it to that file either with
the WWW user interface or with the MML command QKS.
14813
SPECIFIED AREA IS NOT CONFIGURED.
The area cannot be found in the file /etc/iprou.dat. If you
need this area, you must first add it to that file either with
the WWW user interface or with the MML command QKE.
676
DN987378
Issue: 30-0
General Error Messages of System
14814
Error messages
SPECIFIED STUB HOST IS NOT CONFIGURED.
The stub host cannot be found in the file /etc/iprou.dat. If
you need this stub host, you must first add it to that file
either with the WWW user interface or with the MML
command QKJ.
14815
SPECIFIED NETWORK PREFIX IS NOT CONFIGURED.
The network prefix cannot be found in the file
/etc/iprou.dat. If you need this network prefix, you must first
add it to that file either with the WWW user interface or
with the MML command QKH.
14816
SPECIFIED VIRTUAL LINK IS NOT CONFIGURED.
The virtual link cannot be found in the file /etc/iprou.dat. If
you need this virtual link, you must first add it to that file
either with the WWW user interface or with the MML
command QKV.
14817
SPECIFIED NETWORK INTERFACE IS NOT
CONFIGURED
The network interface cannot be found in the file
/etc/iprou.dat. If you need this network interface, you must
first add it to that file either with the WWW user interface or
with the MML command QKF.
14818
ACCESS TO BACKBONE AREA IS REQUIRED IF MORE
THAN ONE AREA IS CONFIGURED
If two or more areas are configured, one of them must be
the backbone area or there must be a virtual link from one
of the areas to the backbone area.
14819
STUBBY AREA CANNOT BE A TRANSIT AREA.
The area cannot be a stubby area and a transit area to the
backbone area at the same time.
14820
THE NETWORK PREFIX IS NOT CORRECT.
The mask length shows the bit after which all bits have to
be zeroes.
14821
THE ROUTER DEAD INTERVAL MUST BE GREATER
THAN THE HELLO INTERVAL
The interval after which router is unavailable must be
greater than the interval for sending HELLO packets.
14822
ENDPOINT SELECTION CONGESTION
Selection of endpoint does not succeed because of the
congestion.
Issue: 30-0
DN987378
677
Error messages
General Error Messages of System
14823
ENDPOINT HANDLING FAILED
Creation or deletion of endpoint has failed.
14824
INVALID TUPLE FOR A STORAGE STRUCTURE
The given tuple cannot be stored into the storage
structure. Typically this means that the home area of the
structure is too small.
14825
NETWORK PREFIX IS ALREADY IN USE IN ANOTHER
AREA
The network prefix is already in use some other area. Use
different address.
14826
HUNTING METHOD CHANGE IS NOT ALLOWED
It is not allowed to change the hunting method of the circuit
croup.
14827
COUNTER ALREADY EXISTS
Counter requested from AAPSEB already exists
14828
COUNTER IS ALREADY REMOVED
Counter requested from AAPSEB is already removed
14829
COUNTER NOT EXISTS
Counter requested from AAPSEB does not exist
14830
BOTH THRESHOLDS ARE REMOVED
Both thresholds whose removing is requested from
AAPSEB are removed
14831
ONE THRESHOLD IS REMOVED
One threshold of the thresholds of this counter is removed.
The another threshold still exists.
14832
THRESHOLD NOT EXISTS
Threshold requested from AAPSEB does not exist.
14833
NO VCC ACTIVE
Counter request for VCC which in not active
14834
COUNTER OPERATION FAILURE
Operation requested for counter failed.
14835
COUNTER RESOURCES ARE FULLY BOOKED
Counter requested cannot be set because resources are
fully booked.
678
DN987378
Issue: 30-0
General Error Messages of System
14836
Error messages
HUNTING OF A PHYSICAL RESOURCE FOR A LEG
HAS FAILED
The hunting of a resource from a given route has failed.
14837
THE LEG IS NOT CONNECTED
The leg is not connected, meaning it is already
disconnected.
14838
RESTRICTED BECAUSE THE SUBSCRIBER IS
TELEMETRIC
Only IMSI, MSISDN, activation status, SAM, VLR address
and/or MSC address can be modified for a telemetric
subscriber.
14839
THE SUBSCRIBER IS NOT A TELEMETRIC
SUBSCRIBER
The operation/modification is suited only for a telemetric
subscriber.
14840
VCCE DOES NOT EXIST
VCC endpoint does not exist.
14841
UX ASIC ALREADY INITIALIZED
UX ASIC already intialized.
14842
MAXIMUM NUMBER OF AAL2 CROSS-CONNECTIONS
HAS BEEN REACHED
The maximum number of AAL2 cross-connections has
been reached for a certain N_CID VCC endpoint. The new
AAL2 cross-connection cannot be accepted.
14843
TERMINATION POINT HAS AN ENDPOINT RELATED TO
IT
The operation could not be performed because there is an
endpoint related to the specified Termination Point. This
error is caused by the missfunctioning of a program block
in the system. Check the computer log file for detailed
information and contact the local customer service.
14844
THE ENDPOINT GROUP IDENTIFIER IS OUT OF ITS
RANGE
The specified identifier for the endpoint group is not within
the range allowed for it. Check the range of the endpoint
group identifier in the Command Manual and try again.
This error might also be caused by the missfunctioning of a
program block in the system. Check the computer log file
for detailed information and contact the local customer
service.
Issue: 30-0
DN987378
679
Error messages
General Error Messages of System
14845
THERE IS NO FREE ENDPOINT GROUP IDENTIFIERS
UNDER THE SPECIFIED ROUTE
There is no free identifier for the endpoint group under the
specified route.This error is caused by the missfunctioning
of a program block in the system. Check the computer log
file for detailed information and contact the local customer
service.
14846
DURING INITIALISATION OF AAL2 CAC STATIC TABLES
ONE TABLE HAS BECOME TOO LARGE
During initialisation of AAL2 CAC static tables one table
has become too large.
14847
DSP APPLICATION OR HARDWARE FAILURE
A DSP application has encountered an error which may be
a result of a hardware fault.
14848
AIHLIB IS NOT INITIALIZED
This error is returned by AIHLIB routines when they are
called before library is initialized by calling aap_init_sar_r
routine.
14849
INVALID PARAMETER PEER ID
This error is returned by AIHLIB routines if incorrect or not
initialized peer id is passed to the routine.
14850
REFERENCED PEER IS NOT ACTIVE
This error is returned by AIHLIB functions when the
operation on non active peer is requested (and the peer is
supposed to be active)
14851
NO DATA RECEIVED
This error is returned by aap_receive_data_r routine when
they werent any data received but the routine was called
anyway. (AIHLIB)
14852
AIHLIB COULD NOT ALLOCATE BUFFER
Returned by AIHLIB routines when the alloc_buffer_r
function failed to allocate data buffer.
14853
INSUFFICIENT AIHLIB TX RESOURCES
Set by AIHLIB TX functions when there are not enough
resources to handle TX channels.
14854
680
INSUFFICIENT MAIN MEMORY FOR AIHLIB
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Returned by AIHLIB initialization routines if there is not
enough memory allocated for AHILIB internal structures.
Usually happens when big amount of channels is
requested.
14855
INSUFFICIENT AIHLIB SAR SRAM MEMORY
Returned by AIHLIB routines if SAR SRAM is not big
enough to create AIHLIB internal and SAR structures.
Usually happens when big amount of channels is
requested.
14856
REQUESTED AIHLIB CHANNEL IS NOT ACTIVE
Returned by AIHLIB routines when the action is to be done
on non active virtual channel (and the channel is supposed
to be active). Usually happens when the channel was not
initialized.
14857
INSUFFICIENT RESOURCES IN AIHLIB VCC POOL
returned by AIHLIB routines when there are not enough
preallocated channels.
14858
INVALID AIHLIB VCC PARAMETER
Returned by AIHLIB routines when invalid or not initalized
VCC is passed to them.
14859
SERVICE CATEGORY NOT SUPPORTED BY AIHLIB
Returned by AIHLIB routines when channel with not
supported service category is requested.
14860
INSUFFICIENT AIHLIB PEER POOL
Returned by AIHLIB routines when there are not enough
preallocated peers available.
14861
AIHLIB VCC IS NOT ACTIVE
Returned by AIHLIB routines when referenced VCC is
active and it is supposed to by non active.
14862
REASSEMBLY OAM DISABLED IN AIHLIB
Returned by AIHLIB routines when RSM OAM is disabled
and it should be enabled.
14863
AIHLIB SEG PRIORITY ERROR
Returned by AIHLIB when the channel with illegal priority
is requested.
14864
Issue: 30-0
NON-REDUNDANT ACTIVE MXU IS RESTARTED
DN987378
681
Error messages
General Error Messages of System
An active MXU restarted when spare MXU cannot be
taken in to use.
14865
SERVICE UNAVAILABLE - WARM-UP IN PROGRESS
Acknowledgement error code to service request, when
service is temporarily unavailable, because of warm-up.
14866
NO CIRCUITS EXIST
None of the circuits to be deleted were found from circuit
groups.
14867
ALL CIRCUITS EXIST
All circuits were already found from correct circuit groups.
14868
THE USAGE OF THE TERMINATION POINT IS NOT THE
ONE SPECIFIED
The termination point is not in the specified usage and
therefore the requested operation is not allowed. This error
might be caused by the missfunctioning of a program block
in the system. Check the computer log(s) for detailed
information and contact the local customer service.
14869
THE OPERATION IS NOT IMPLEMENTED
The requested operation is not implemented yet. Check
the computer log(s) for detailed information.
14870
NO RESPONSE FROM STATISTICAL PROGRAM BLOCK
An acknowledgement for the sent message was not
received from the statistical program block
(EXSPRO/MDUPRB/STPROC). The reason for the error
may be that there is a momentary overload in the statistical
program block.
14871
STATISTICAL DATA COLLECTION NOT STARTED
The statistical program block
(EXSPRO/MDUPRB/STPROC) cannot start the requested
data collection for the statistical measurement. The reason
for the error may be that the MDFFIL file is corrupted and
so the requested data collection is incorrect.
14872
STATISTICAL DATA COLLECTION NOT STOPPED
The statistical program block
(EXSPRO/MDUPRB/STPROC) cannot stop the requested
data collection.
14873
682
ERROR IN REQUESTED SERVICE FROM STATISTICAL
FILE SERVICES PROGRAM BLOCK
DN987378
Issue: 30-0
General Error Messages of System
Error messages
The error code originates from the Statistical File Services
Program Block upon detection of an invalid parameter in a
service request.
14875
RESOURCE REMOVAL NOT FULLY PERFORMED
Resource removal was not fully performed.
14876
UNABLE TO ACTIVATE HOT DATA DISK BUFFERING
Activation of the hot data disk buffering failed.
14877
MASTER BTS OF SEG NOT FOUND IN RNW DATABASE
The segment has no master BTS.
14878
SEG NOT FOUND IN RNW DATABASE
The segment has not been created into the RNW
database.
14879
ILLEGAL SEG ID
An attempt has been made to use illegal or incompatible
SEG identification.
14880
THERE ARE TOO MANY BTSS IN ONE SEG
The maximum number of BTSs is already created to the
segment.
14881
THERE ARE TOO MANY TRXS IN ONE SEG
The maximum number of transceivers allowed in the
segment has been reached.
14882
MOVING OF BTS CONTAINING BCCH TRX NOT
ALLOWED
BTS containing BCCH TRX can not be moved to an
another segment.
14883
SEGMENT USAGE OPTION NOT IN USE IN BSC
Segment usage option is not in use in the BSC.
14884
SEG NAME ALREADY IN USE
A SEG name must be unique in the BSC.
14885
SEG NAME IS ILLEGAL
A SEG name may consist of allowed characters only.
14886
ILLEGAL VALUE OF MULTIBCFMASTER
Parameter multiBCFmaster has illegal value.
Issue: 30-0
DN987378
683
Error messages
General Error Messages of System
14887
MOVING OF MASTER BTS NOT ALLOWED
Master BTS can not be moved to another segment.
14888
NOT MASTER BTS
Some operation has been tried to do to a BTS which is not
a master BTS.
14889
ILLEGAL BTS ID
An attempt has been made to use illegal or incompatible
BTS identification.
14890
MASTER BTS SHIFT IS ALLOWED ONLY BETWEEN
BASE TRANSCEIVER STATIONS OF SAME SEGMENT
Master BTS information can not be shifted to BTS in
another segment.
14891
TOO MANY BASE TRANSCEIVER STATIONS IN
SOURCE SEGMENT
There can be only one BTS (master BTS) in the segment
when master BTS is tried to be moved to another segment.
14892
VIRTUAL FILE LOADING IS GOING ON
When the virtual file loading is going on, switchover and
state change may not be done to the source unit.
14893
LOADING LOG BUFFERS DURING DATABASE WARM
UP FAILED
The database warm up library could not load log buffers
from working unit to the spare unit during database warm
up. Database warm up failed.
14894
DYNAMIC ABIS POOL WAS NOT FOUND IN RNW
DATABASE
The Dynamic Abis pool has not been created into the
RNW database.
14895
NO MORE TRANSCEIVERS CAN BE ATTACHED IN
SAME DYNAMIC ABIS POOL
The maximum number of transceivers allowed in the
Dynamic Abis pool has been reached.
14896
GATEWAY DXT CANNOT BE REMOVED FROM A
SUBNET
The DXT to be removed from a subnet cannot be the
Gateway of the subnet
684
DN987378
Issue: 30-0
General Error Messages of System
14897
Error messages
PARAMETER TIME GROUP OF ADJACENT CELL
DIFFERS FROM CORRESPONDING OWN CELL VALUE
The time group parameter value given to an adjacent cell
to be created or modified differs from that of the own cell.
14898
TRANSMISSION EQUIPMENT IN BSS
SYNCHRONIZATION USE
Transmission equipment deletion is not possible because it
is used for BSS synchronization purposes. Remove it from
BSS synchronization use and try again.
14899
RESERVATION IS PUT INTO QUEUE
Reservation of WBTS failed, but reservation is put into
queue.
14900
RADIONETWORK DATABASE WAS RESERVED FOR
SOME OTHER OPERATION
Requested operation cannot be performed because some
other operation (e.g. some plan operation) has reserved
the whole radionetwork database.
14901
RESERVATION FAILED
Reservation of WBTS failed because it is already reserved.
14902
RESERVATION IS PUT INTO QUEUE.
Reservation of database failed but reservation is put into
queue. New reservations for WBTS are not allowed.
14903
OPERATION REQUIRES THAT ALL WCELS UNDER THE
WBTS MUST BE LOCKED
Requested operation failed because not all WCELs under
the WBTS were locked.
14904
MAXIMUM NUMBER OF WBTSS EXCEEDED
WBTS creation failed because maximum number of
WBTSs has already been created to the RNW database.
14905
MAXIMUM NUMBER OF WCELS EXCEEDED
WCEL creation failed because maximum number of
WCELs has already been created to the RNW database.
14906
MAXIMUM NUMBER OF WCELS UNDER WBTS
EXCEEDED
WCEL creation failed because maximum number of
WCELs has already been created under the WBTS.
Issue: 30-0
DN987378
685
Error messages
General Error Messages of System
14907
SOME OTHER OPERATION IS GOING ON TO SAME
OBJECT OR PARENT OBJECT
Operation could not be performed because the object was
undergoing some other operation at the same time.
14908
NO ANSWER RECEIVED FROM PROCESS HA3 IN TIME
Timer for waiting an answer message from process HA3
has expired, and no answer has been received.
14909
NO ANSWER RECEIVED FROM PROCESS VEXELI IN
TIME
Timer for waiting an answer from VEXELI has expired and
no answer has been received.
14910
SERVICE PROVIDER PID IS NOT FOUND
The PID of the program block offering the needed service
could not be resolved.
14911
NO ANSWER RECEIVED FROM BRM IN TIME
Timer for waiting an answer from BRM has expired, and no
answer has been received.
14912
COCO OBJECT IS BEING USED BY SOME WBTS
CoCo can not be connected to the requested WBTS
because it is already being used by some WBTS.
14913
TIMER FOR WAITING ANSWER FROM OBHERO
EXPIRED
Timer set for waiting an answer from OBHERO has
expired and no answer has been received.
14914
POSITION BASED SERVICES OPTION IS NOT IN USE
IN BSC
The Position Based Services option is not in use in BSC.
The purpose of the Position Based Service in BSC feature
is to locate subscriber and/or validate mobile equipment or
to send the assistance data to the MS.
14915
SOME SUBTIMESLOTS ARE MISSING FROM REQUEST
All subtimeslots of physical timeslot were not given.
14916
SOME WCELS EXIST UNDER THE WBTS TO BE
DELETED
WBTS can not be deleted from database while there are
WCELs under it.
14917
686
SIGNALLING LINK IN USE
DN987378
Issue: 30-0
General Error Messages of System
Error messages
Signalling link release is not allowed due the on-going user
data connections. The protocol state inside the signalling
link prohibits release. Try again release with an override
parameter if you are absolutely sure that the signalling link
can be released despite of the protocol state.
14918
MISMATCH BETWEEN COCO ID AND C-NBAP PARAMS
IN WBTS AND COCO-OBJECT
The CoCo object (specified with CoCo id) in database has
different C-NBAP parameters than those specified in
WBTS, or the C-NBAP address specified in WBTS is not
defined in CoCo as C-NBAP address.
14919
OPERATION REQUIRES WCEL OBJECT TO BE
LOCKED
The requested operation can not be done because it
requires the WCEL state to be locked (bl- by user).
14920
NO ANSWER RECEIVED FROM PROCESS REKOVE IN
TIME
Timer for waiting a response from REKOVE has expired
and no response has been received.
14921
NO ANSWER RECEIVED FROM PROCESS REZINI IN
TIME
Timer set for waiting a response from rezini has expired
and no response has been received.
14922
INVALID STATE ACTION VALUE
The value of state action parameter (in WCEL state
change) is incorrect.
14923
DURING EXECUTION OF THE AAL2 CAC ALGORITHM
A CHECK OF AN ARITHMETIC FIELD HAS FAILED
During execution of the AAL2 CAC algorithm, a check of
an arithmetic field has failed. This indicates for instance
that a certain field is out of its bounds (e.g. calculation
safety bounds).
14924
TIME FOR WAITING RESPONSE FROM RRCPRB IS UP
A timer set for waiting a response from rrc process has
expired and no response has been received.
14925
WRONG COMPUTER UNIT ERROR
An attempt has been made to give the task to a wrong
computer unit.
14926
Issue: 30-0
INVALID MACS
DN987378
687
Error messages
General Error Messages of System
The value of MACS (Message Authentication Code for
Synchronisation) was not the expected value.
14929
THE SPECIFIED INTERFACE DOES NOT EXIST
Interface switchover can not be executed because the
target interface does not exist
14930
UNIT IS STARTING UP
Operation is not allowed because unit is restarting.
14931
UNIT IS UNDER PERIODICAL MONITORING
Switchover is not allowed because unit is under
periodically monitoring.
14932
WBTS COLLECTION FULL
There is no room for a new Base Station (WBTS) object in
radio network database.
14933
INTERNAL ERROR IN RNW DATABASE
An internal error has occured in radio network database.
14934
FMC STILL USED BY SOME WCEL
FMC can not be deleted, because it is still used by some
WCEL.
14935
MULTI BCF OPTION IS NOT IN USE IN THE BSC
The option Multi BCF is not in use in the BSC.
14936
COMMON BCCH GSM 900 OPTION IS NOT IN USE IN
THE BSC
The Common BCCH GSM 900 option is not in use in the
BSC.
14937
COMMON BCCH GSM 1800 OPTION IS NOT IN USE IN
THE BSC
The Common BCCH GSM 1800 option is not in use in the
BSC.
14938
BTS SITE TYPE MODIFICATION NOT ALLOWED FOR
BCF WITH SEG OF SEVERAL BTS
The modification of the BTS site type is not possible if the
BCF in question contains segments of more than one BTS.
14939
SEG NOT ALLOWED FOR 2ND GENERATION SITE
TYPE
The segment is not allowed for the Nokia 2nd generation
site type.
688
DN987378
Issue: 30-0
General Error Messages of System
14940
Error messages
PRIMESITE CAN ONLY HAVE SEG WITH ONE BCF
The Nokia PrimeSite can only have segments with one
BCF.
14941
ILLEGAL SEG CONFIGURATION
The segment configuration is illegal.
14942
THE FREQUENCY BAND IS INCORRECT FOR SEG
This frequency band is not allowed for segment with
several different frequency bands.
14943
INSITE DOES NOT SUPPORT THE COMMON BCCH
FEATURE
The Nokia InSite does not support the feature Common
BCCH.
14944
SEG WITH ONE BTS CANNOT BE MOVED TO A
NONEXISTING SEG
A segment with one BTS cannot be moved to a new
segment.
14945
EGPRS CLASSIC DOES NOT SUPPORT THIS BTS SITE
TYPE
The feature EGPRS Classic does not support this BTS site
type.
14946
EGPRS COMPACT DOES NOT SUPPORT THIS BTS
SITE TYPE
The feature EGPRS Compact does not support this BTS
site type.
14947
BB HOPPING IS NOT SUPPORTED BY EGPRS
COMPACT
The base band hopping is not supported by the feature
EGPRS Compact.
14948
THE PARAMETER CANNOT BE MODIFIED
The parameter cannot be modified by user.
14949
THE RADIO TIME SLOTS FROM 1 TO 7 HAVE TO BE
TCHF
The radio time slots from 1 to 7 have to be of TCHF type.
14950
Issue: 30-0
TSC (TRX) AND BCC (CELL) VALUES MUST BE EQUAL
IN BB-HOPPING LAYER
DN987378
689
Error messages
General Error Messages of System
The Training Sequence Codes of the TRXs and the BTS
Colour Code of BB-hopping layer, which has BCCH or
PBCCH TRX, must be equal.
14951
UPDATING THE CURRENT TIME FAILED BECAUSE
O&M LINK BUSY
The current time cannot be updated for BTS because the
O&M link is busy.
14952
RDOMAN HAS NOT RESPONDED TO SERVICE
REQUEST
RDOMAN has not responded to service request.
14953
RDOMAN UNIT CPU LOAD TOO HIGH
RDOMAN has rejected service request because of a too
high CPU load in its unit.
14954
RDOMAS FAILED TO CREATE HAND PROCESS
Service request can not be processed, because RDOMAS
failed to reserve a hand process for it.
14955
RDOHAN FROZE WHILE RUNNING REQUEST
RDOHAN hand process froze while attempting to process
the service request. RDOHAN was stopped.
14956
MSISDN NUMBER REFERS TO INTERNAL
SUBSCRIBER
While creating a relation between FSSN and MSISDN,
MSISDN was already in relation with an internal
subscriber.
14957
DATA BUS TEST FAILS
Testing of the memory data bus fails.
14958
ADDRESS BUS TEST FAILS
Testing of the memory address bus fails.
14959
MEMORY DEVICE TEST FAILS
Testing of the memory device fails.
14960
COCO ID AND WBTS ID DO NOT MATCH
The CoCo ID and WBTS ID given in the service request
are not related to each other in the system.
14961
CONTROL/USER PLANE DELETION FAILED
Control/User plane deletion was not completed
successfully.
690
DN987378
Issue: 30-0
General Error Messages of System
14962
Error messages
CONTROL/USER PLANE CREATION FAILED
Control/User plane configuration was not completed
successfully.
14963
GIVEN VCI VALUE IS ALREADY IN USE
The given VCI value is already used by some other
instance.
14964
AAL2 SIGNALLING VCI IS USED BY AAL2 UPLINK
The AAL2 signalling link is used by AAL2 user plane link.
14965
ATM MODIFICATION IS NOT ALLOWED IN THIS CASE
ATM modification is not allowed with this service for the
connected CoCo object.
14966
O&M IP OVER ATM LINK ALREADY EXISTS
The DCN for O&M IP over ATM link already exists for the
given ATM interface.
14967
NUMBER OF EGPRS COMPACT CONTROL BLOCKS IS
UNDER 4
The total amount of control blocks (CPBCCH and
CPCCCH) has to be at least 4 when EGPRS Compact is in
use.
14968
ILLEGAL CPBCH LOCATION
Compact packet broadcast control channel (CPBCH) was
in other timeslot than RTSL 0.
14969
GPRS ENABLED TRX IS NOT EDGE CAPABLE
HW of GPRS Enabled TRX is not EGPRS-compatible with
a BTS which has EGPRS (Enhanced General Packet
Radio Service) enabled.
14970
ERROR IN I2PLIB MODULE
The service request could not be processed, because
operating the shared memory via I2PLIB function returned
an error code.
14971
ERROR IN HEADER COMPRESSION MODULE
The service request could not be processed, because
operating the header compression module returned an
error code.
14972
Issue: 30-0
ALLOCATING RESOURCES FOR HEADER
COMPRESSION FAILED
DN987378
691
Error messages
General Error Messages of System
Resources for the header compression algorithm could not
be allocated. However, the request was otherwise served
and the channel is ready to continue in operation using
given parameters, but without support for the header
compression.
14973
CONTROL CHANNEL TERMINATION MANAGEMENT
SERVICE NOT AVAILABLE
The control channel termination management service
cannot be found in the system.
14974
ATM LOGICAL RESOURCE MANAGEMENT SERVICE
NOT AVAILABLE
The ATM logical resource management service cannot be
found in the system.
14975
SERVICE FOR CREATING OR DELETING THE DIGIT
ANALYSIS NOT AVAILABLE
The service for creating or deleting the digit analysis
cannot be found in the system.
14976
ATM ROUTE MANAGEMENT SERVICE NOT AVAILABLE
The ATM route management service cannot be found in
the system.
14977
RE