Republic of the Philippines
Department of Education
Region VI – Western Visayas
Division of Roxas City
CONGRESSMAN RAMON A. ARNALDO HIGH SCHOOL
(Technical – Vocational High School)
Banica, Roxas City
Date _______________
ASSESSMENT FOR
FIRST QUARTER LESSON
GRADE - 10
TVE-10- ELECTRICAL INSTALLATION AND MAINTENANCE NC-II
Name __________________________ Section __________________ Contact Number _____________
Direction: Multiple Choice. Read each statement carefully, then write the letter of the correct answer on the
space provided before each number.
______ 1. Electrical materials are developed and constructed to____________________.
a. allow and control the flow of current in an electrical circuit
b. hold and secure wires to its fixtures or devices
c. protect houses, buildings, appliances and instruments from damage
d. all of the above
______ 2. This is used for griping, holding, cutting electrical wires and cables and even small nails. Usually
used by linemen in doing heavy tasks.
a. long nose plier
c. electrician’s Knife
b. combination plier
d. wire stripper
______ 3. This screw driver has a crossed tip resembling a positive (+) sign. It is used to drive screws with
cross slot heads.
a. flat/standard screw driver
c. allen wrench
b. Philip screw driver
d. stubby screw driver
______ 4. A small drilling machine with a chuck capacity of ¼ inch to 3/8 inch. It is used in making holes on
metal sheets and concrete walls.
a. flat/standard screw driver
c. allen wrench
b. Philip screw driver
d. stubby screw driver
______ 5. This is a circuit protective device that automatically blows and cut the current when an over load or
short circuit happens.
a. fuse
c. ground wire
b. jumper
d. switch
______ 6. An electrical device that acts as a convenient source of electrical energy for current consuming
appliance or equipment
a. receptacle
c. convenience outlet
b. switch
d. electric meter
______ 7. An electrical materials used for the passage, protection and insulation of wires.
a. connectors
c. junction box
b. utility box
d. conduit
______ 8. An electrical wire that is made of a single strand of copper or aluminum wire.
a. solid wire
c. flexible wire
b. stranded wire
d. G.I. wire
______ 9. It is an octagonal-shaped electrical material where the connections or joints of wires are being done.
It is also where the flush type lamp holder is attached.
a. junction box
c. square box
b. utility box
d. panel board
______10. Electrical material that is used to hold and anchor electrical conduits to its proper position.
a. electrical tape
c. screw
b. connector
d. clamp
______11. This is a rectangular shaped metallic or plastic (PVC) material in which flush type convenience
outlet and switch are attached.
a. junction box
c. square box
b. utility box
d. panel board
______12. An electrical materials used to attach conduits to a junction box or utility box
a. connectors
c. junction box
b. utility box
d. conduit
______13. A duplex stranded wire usually used in appliances, extension cords, and temporary wiring
installations.
a. flat cord wire
c. solid coper wire
b. pdx wire
d. galvanized iron wire
______14. An electrical device that hold and protect the lamp.
a. plug
c. panel board
b. receptacle
d. bulb
______15. An electrical materials used to attach conduits to a junction box or utility box
a. connectors
c. junction box
b. utility box
d. conduit
______16. It is a written or printed request of something that is needed. It is also called Purchase Request
Form.
a. job order form
c. requisition slip form
b. inventory form
d. borrower’s form
______17. A list of tools, equipment or materials made on a particular date by a qualified personnel. It also
provides information on the quantity and condition of the items listed.
a. job order form
c. requisition slip form
b. inventory form
d. borrower’s form
______18. A ‘terms and conditions” on borrowing tools or equipment is found on this form.
a. borrower’s form
c. requisition slip form
b. inventory form
d. job order form
______19. An electrical equipment that is used to make holes on metal sheets, wood or concrete.
a. portable electric grinder
c. electric planer
b. portable electric drill
d. screw driver
______20. A device inserted into a convenience outlet to conduct electric current.
a. socket
c. tester
b. plug
d. screw driver
______21. A tool used by linemen to remove insulation of large wires and cables.
a. wire crimper
b. electrician’s knife
c. adjustable wrench
d. long nose plier
______22. An instrument used to measure the amount of electrical current intensity in a circuit.
a. Voltmeter
c. Micrometer
b. Ammeter
d. Ohmmeter
______23. A pocket sized tool used to test the line wire or circuit if there is current in it.
a. Test light
c. Ruler
b. Wire gauge
d. Pull-push rule
______24. A measuring tool used to measure the length of an object in centimeter and inches.
a. Test light
c. Ruler
b. Wire gauge
d. Pull-push rule
______25. It is used to measure the diameter of wires/conductors in circular mils. It can measure small and big
sizes of wires and cables.
a. Voltmeter
c. Micrometer
b. Ammeter
d. Ohmmeter
______26. It is used to measure the voltage, resistance and current of a circuit. It connected in parallel or series
with the circuit depending on what to measure.
a. Volt-Ohm-meter
c. Ohmmeter
b. Micrometer
d. Ammeter
______27. A series of markings found on the multi-tester used for reading values.
a. probe
b. scale
c. cover
d. face
______28. When the multi-tester is not in use, the selector switch should be set to OFF position or;
a. 10x
b. 1000x
c. 1000v
d. 750v
______29. Part of a multi-tester that is used to connect to the object being tested.
a. pointer
b. adjustment screw c. scale d. probe
______30. Part of a multi-tester used to zero-in the pointer before measuring resistance.
a. adjustment screw b. pointer
c. zero-ohm adjusting knob d. scale
II – System of Measurement
A. Direction: Write the equivalent value of the given units;
31. 1 centimeter (cm)
=
__________ millimeter (mm)
32. 1 yard
=
__________ inches
33. 1 decimeter (dm)
=
__________ centimeters (cm)
34. 10 millimeter (mm)
=
__________ centimeter (cm)
35. 1 foot
=
__________ inches
B. Directions: Write the correct unit abbreviation of the following:
________36. Centimeter
________37. Meter
________38. Decimeter
________39. Yard
________40. Feet
C. Directions: Convert the following:
41. 10 feet
=
________centimeters
42. 70 centimeters
=
________millimeters
43. 15 inches
=
________ feet
44. 5 meters
=
________ yards
45. 1 meter
=
________ centimeters
46. 1 kilometer
=
________ meters
47. 3 yards
=
________ feet
48. 48 inches
=
_______ yards
49. 2000 meters
=
_______ kilometers
50. 5 feet
=
_______ inches
Prepared By:
JOHN REY H. VIDAL
Teacher I
CHECKED BY:
MERVINA A. CASTEJON
MT-I, TVE Coordinator
Approved:
RODRIGO D. JEREMIAS, JR.
Secondary School Principal IV