Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Alternative fuels
Information Type:
Operator's Information
Profil e:
Wheel Loaders
Location:
Fuel system/Specifications
Date:
11- 08-202 3
Alternative fuels
Showing Selected Profile
This statement is only valid for Volvo branded engines.
Hydro-treated vegetable oil (HVO) and fatty acid methyl ester (FAME) biodiesel are both made from renewable raw materials
such as vegetable oils and animal fats, but they are chemically processed in different ways.
Hydro-treated vegetable oil (HVO)
HVO is created using a chemical process called hydro-treating. Hydro-treating creates an oxygen-free hydrocarbon product that
is very similar to distillate diesel fuel and is well suited for use in diesel engines. HVO fuels complying with the CEN diesel fuel
standard EN 590:2013 or with the European Fuel Quality Directive 98/70/EC are approved for use in all Volvo Construction
Equipment diesel engines with no changes to maintenance intervals. Paraffinic diesel fuels complyingwith the CEN standard EN
15940 may be used in all machines operating outside the European Union and for EU-certified engines up to the emission level
Stage IV. These fuels may also be used for the EU-certified D11, D13 and D16 engines meeting the emission level Stage V.
B iodiesel
Biodiesel is a product made from renewable resources such as vegetable oils or animal fat. Biodiesel that has been chemically
processed into fatty acid methyl ester (FAME) can be blended with distillate diesel fuel and used insome diesel engines.
Unblended biodiesel is referred to as B100 because it is 100% biodiesel.
Rapeseed methyl ester (RME) is the most common type of FAME used in Europe. Soy methyl ester (SME) and sunflower oil
methyl ester (SOME) are the most common types of FAME used in the US.
Although use of FAME biodiesel is now a legal requirement in some markets, it is not as suitable for use in diesel engines as
conventional diesel fuel or HVO (hydro-treated vegetable oil).
Biodiesel fuel requirements
The FAME biodiesel blends specified in the table below are approved for use if:
The biodiesel is pre-blended by the fuel supplier
The biodiesel used in the blend conforms to EN14214 or ASTM D6751
The distillate fuel used in the blend meets fuel sulphur requirements
The distillate fuel used in the blend conforms to EN590 or ASTM D975
B1-B5 biodiesel blends conform to EN590 or ASTM D975
B6-B7 biodiesel blends conform to EN590 or ASTM D7467
B8-B20 biodiesel blends conform to EN16709(B20) or ASTM D7467
Engine emission designation
Engine size
Acceptable blend
EU Stage II / US Tier 2 *
EU Stage IIIA / US Tier 3 *
EU Stage IIIB / US Tier 4
interim EU Stage IV / US Tier 4
final
EU Stage V
Below D4 / 4 litres
Up to B7
D4–D8
Up to B7
D9–D16
Up to B20
EU Stage II / US Tier 2 *
EU Stage IIIA / US Tier 3 *
EU Stage IIIB / US Tier 4
interim
EU Stage IV / US Tier 4 final
EU Stage II / US Tier 2 *
EU Stage IIIA / US Tier 3 *
US Tier 4 final, special North America arrangement **
EU Stage IIIB / US Tier 4 interimD11–D16Up to B10
EU Stage IV / US Tier 4 final
EU Stage IIIB / US Tier 4 interim, equipped with High Sulphur Fuel D4–D16Up to B20
Conversion Kit (only available in unregulated markets)
EU Stage IV / US Tier 4 final, equipped with High Sulphur Fuel Conversion
Kit (only available in unregulated markets)
EU Stage VD4–D16Up to B7
* As Tier 2 and Tier 3 emissions regulations ended in 2005 and 2010 respectively, engines producedsince then typically meet
Stage II / Stage IIIA regulations, allowing their sale in less regulated markets.
** With additional restrictions and special operating conditions, equipment used in North America may operate on B20 diesel.
NOTE!
Failures directly caused by the use of poor quality biofuel, or any other fuel not conforming to standards, are not factory defects
and the manufacturer’s warranty does not apply.
Maintenance interval requirements
Additional service actions and shorter maintenance intervals are mandatory when using biodiesel blends above B10.
Every 10 hours
Check the engine oil and change if it rises above the maximum fill level
Inspect the fuel system components and replace as necessary
Half of original interval
Change the engine oil and filter
Replace the fuel filter(s)
Every year, regardless of operating hours
Change the engine oil and filter
Clean the fuel tank
Effects of biodiesel on engine oil
Using biodiesel can lead to increased oil dilution. Use engine oil analysis tools frequently to check for fuel dilution and monitor
engine oil condition. Check the engine oil level daily. Always change the engine oil if the oil level rises above the maximumfill l
evel.
Effects of biodiesel on fuel systems
Biodiesel dissolves and loosens some fuel system deposits. During the initial conversion to biodiesel, loosened deposits will
travel to the fuel filters and require more frequent fuel filter replacements. Start with new fuel filters when using biodiesel for the
first time.
Biodiesel is aggressive to some materials used in fuel system components. Inspect seals, hoses, rubber and plastic components
every 10 hours. Repair or replace any components that are damaged, softened or leaking. Clean biodiesel from painted surfaces
immediately to prevent paint damage.
Biodiesel is more sensitive to bacteria and water contamination than distillate diesel fuel.
Use as much fuel as possible before refilling the fuel tank in order to prevent bacteria growth if a machine is in regular
use, e.g. regularly uses up a tank of fuel within a week. In climates where condensation is a risk, or when the machine is
working for short durations, keep the fuel tank full.
Do not use biodiesel in machines with low utilization or operating time.
Do not store machines for more than 4 weeks without flushing biodiesel out of the fuel system by operating the
machine through at least one full tank of distillate diesel fuel.
Always follow the manufacturer’s storage recommendations and “best-before” dates for each delivery of biodiesel.
Effects of biodiesel on exhaust aftertreatment systems
Biodiesel leaves higher levels of ash in diesel particulate filters and may require more frequent diesel particulate filter (DPF)
regeneration and cleaning. Biodiesel can cause deviations in temperatures and functionality of the DPF burner and may cause
fault codes or errors.
Biodiesel exhaust gas is aggressive to some materials used in selective catalytic reduction systems(SCR) and may require more
frequent cleaning, repairing or replacing of SCR parts.
Effects of biodiesel on cold weather operation
Biodiesel has a high viscosity at temperatures below 0 ˚C (32 ˚F) and may cause problems starting the engine. Use a fuel heater
or park machines in a heated building if possible.
Effects of biodiesel on engine performance
Biodiesel B100 has about 8% lower energy density compared to regular diesel fuel. Blends equal or lower than B20 have a small
impact on engine performance.
Effects of biodiesel on emissions compliance
Engines are certified to comply with U.S. EPA, California and EU emissions standards based upon theuse of test fuels with
specifications established by these regulatory agencies. Alternative fuels, including biodiesel, that are not substantially similar to
the required test fuels may adversely affect engine emissions compliance. As a result, Volvo does not warrant that the enginewill
conform to applicable Federal or California and EU emissions limits when operated on, or having previously being operated on,
biodiesel or other alternative fuels that are not substantially similar to specified test fuels usedfor certification, nor if biodiesel /
regular diesel is used in blends that exceed the recommendations.
However, the use of biodiesel up to a maximum of 20% (B20) in and of itself, will not affect the manufacturer's mechanical
warranty as to engine or emissions system, provided the bio fuel used in the blend conforms to the applicable standards and the
additional steps outlined herein are followed.
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Automatic central lubrication
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Recommended lubricants/Specifications
Automatic central lubrication
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
L70E, L70G Volvo
Recommended lubricants
The following requirements apply to grease to be used in the central greasing system:
the grease may notcontain graphite or PTFE (teflon)
use is permitted of grease containing max. 5% molybdenum disulphide (MoS ₂)
the following NLGI-class is recommended at operating temperature between:
Operating temperature range
NLGI-class
–20 °C (–4 °F) to +70 °C (158 °F)
2
<–20 °C (–4 °F) to 0 °C (32 °F)
0/1
<–20 °C (–4 °F) to +70 °C (158 °F)
synthetic 2
<–20 °C (–4 °F) to 0 °C (32 °F)
synthetic 0 / 1
Serial number stop
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Axles
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Transmission/Specifications
Axles
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Type
Fully floating drive shafts with planetary gear hub reductions
Front axle, make
Volvo
Designation
AWB 15
Rear axle, make
Volvo
Designation
AWB 15
Differential lock
On front axle
Operation, differential lock
Ele ct ro-hyd rauli c
L70G
Type
Fully floating drive shafts with planetary gear hub reductions
Front axle, make
Volvo
Designation
AWB 25
Rear axle, make
Volvo
Designation
AWB 20
Differential lock
On front axle
Operation, differential lock
Ele ct ro-hyd rauli c
L90G
Type
Fully floating drive shafts with planetary gear hub reductions
Front axle, make
Volvo
Designation
AWB 25
Rear axle, make
Volvo
Designation
AWB 20
Differential lock
On front axle
Operation, differential lock
Ele ct ro-hyd rauli c
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Brake system
Information Type:
Operator's Information
Profil e:
L70E, L70G Volvo
Location:
Brake/Specifications
Date:
11- 08-202 3
Brake system
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Service brakes
Service brakes, type
Dual circuit, all-hydraulic, wet disc brake
Number of discs per wheel front/rear
1/1
Accumulator volume
3 x 0.5 litre (0.13 gal)
Service brakes, disc thickness, new
9.5 mm (0.37 in)
Service brakes, disc thickness, minimum
7.2 mm (0.28 in)
Parking brake
Type
Electrically operated hydraulic disc brake
Parking brake, disc thickness, new
12.4–13.0 mm (0.40–0.51 in)
Parking brake, disc thickness, minimum
10 mm (0.39 in)
L70G
Service brakes
Service brakes, type
Dual circuit, all-hydraulic, wet disc brake
Number of discs per wheel front/rear
1/1
Accumulator volume
2 × 0.5 litre (0.13 gal) + 1 × 1.0 litre (0.26 gal)
Service brakes, disc thickness, new
9.5 mm (0.37 in)
Service brakes, disc thickness, minimum
7.2 mm (0.28 in)
Parking brake
Type
Electrically operated hydraulic disc brake
Parking brake, disc thickness, new
12.4–13.0 mm (0.40–0.51 in)
Parking brake, disc thickness, minimum
10 mm (0.39 in)
L90G
Service brakes
Service brakes, type
Dual circuit, all-hydraulic, wet disc brake
Number of discs per wheel front/rear
1/1
Accumulator volume
2 × 0.5 litre (0.13 gal) + 1 × 1.0 litre (0.26 gal)
Service brakes, disc thickness, new
9.5 mm (0.37 in)
Service brakes, disc thickness, minimum
7.2 mm (0.28 in)
Parking brake
Type
Electrically operated hydraulic disc brake
Parking brake, disc thickness, new
12.4–13.0 mm (0.40–0.51 in)
Parking brake, disc thickness, minimum
10 mm (0.39 in)
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Cab
Information Type:
Operator's Information
Profil e:
L70E, L70G Volvo
Location:
Cab/Specifications
Date:
11- 08-202 3
Cab
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
General
The cab is mounted on rubber pads, is insulated and has a flat floor with rubber mat.
Tested and approved as a protective cab and meets standards according to ISO/DIS 3471-1:2004 (ROPS), ISO/DIS 3449-2004
(FOPS tier II) as well as ISO 6055-1997 (protective roof for high-lifting rider trucks).
Cab interior fittings and upholsteryFire retardant (fire resistant) measured according to ISO
3795-1989
Number of emergency exits2 (door and right side window)
Heating and ventilation
The basic version of the loader is provided with a heating and ventilation system with defrosting for all windows and the best
possible air distribution (10 air vents). Air conditioning is available as optional extra.
Operator's seat
This machine is equipped with an operator's seat that meets the vibration-damping criteria for EN ISO 7096.
Height adjustment (rapid adjustment)100 mm (4 in)
Longitudinal adjustment160 mm (6 in)
Adjustment for operator weight40–130 kg (88–287 lb) / 40–160 kg (88–353 lb) (HD-seat (optional
equipment))
Adjustment of backrest, (adjustable backrest angle)12°
Upholstery Fire-resistant
Lap-type seatbelt with rollerYes
Hand-arm vibrations
Emission of hand-arm vibrations during real operating conditions at its intended use is less than 2.5 m/s²RMS (root mean
square) acceleration according to ISO 8041.
Whole-body vibrations
Emission of Whole-Body Vibration during real operating conditions at its intended use is accordingto the table below.
Typical operating conditions
Vibration emissions, value
a
,ᵉ
(m/s² RMS)
Vibration emissions, value
a
,ᵉ
(m/s² RMS)
Vibration emissions, value
a
,ᵉ
(m/s² RMS)
Load/carry handling
0.6
0.6
0.5
Mining application0,8
0.
0,
Transport operation0.5
7
8
V-shaped load and carry 0.7
handling
0.
0.
7
5
0.
0.
6
5
The following vibration directions are defined:
x = longitudinal
y = lateral
z = vertical
NOTE!
These whole-body vibration emission values were determined at particular operating and ground conditions and are therefore
not representative for all the various conditions according to the intended use of the machine and should not alone be used to
determine the whole-body vibration exposure to the operator using the machine. For this purpose the information in ISO/TR
25398 is recommended.
To ensure that the generated whole-body vibration emissions during machine use is kept to a minimum, see page Whole-body
vibrations.
Sound information, L60G
Sound pressure level (LpA) at operator's position68 dB (A)
(Measuring method according to ISO 6396)
Sound power level (LWA) around the machine105 dB (A)
(Measurement according to 2000/14/EC with applicable appendices and
measuring method according to ISO 6395)
Sound information, L70G
Sound pressure level (LpA) at operator's position68 dB (A)
(Measuring method according to ISO 6396)
Sound power level (LWA) around the machine105 dB (A)
(Measurement according to 2000/14/EC with applicable appendices and
measuring method according to ISO 6395)
Sound information, L90G
Sound pressure level (LpA) at operator's position68 dB (A)
(Measuring method according to ISO 6396)
Sound power level (LWA) around the machine105 dB (A)
(Measurement according to 2000/14/EC with applicable appendices and
measuring method according to ISO 6395)
NOTE!
Uncertainties in stated noise values (e.g., uncertainty in production and measuring instruments) are calculated according toISO
6395:2008 for sound power level around the machine and ISO 6396:2008 for sound pressure level at theoperator's station.
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Change capacities
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Service capacities and change intervals/Specifications
Change capacities
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Capacities
When changing
Engine oil, incl. filter
18 litres (4.8 US gal)
Transmission incl. filter
29 litres (7.7 US gal)
Front axle
24 litres (6.3 US gal)
Rear axle
24 litres (6.3 US gal)
Hydraulic system
Hydraulic oil tank
135 litres (35.7 US gal)
90 litres (23.8 US gal)
Fuel tank
Cooling system
Total
224 litres (59.2 US gal)
30 litres (7.9 US gal)
Oil-bath air cleaner (optional equipment)
38 litres (10.0 US gal)
5.5 litres (14.5 US gal)
L70G
Capacities
When changing
Engine oil, incl. filter
18 litres (4.8 US gal)
Transmission incl. filter
29 litres (7.7 US gal)
Front axle
38 litres (10.0 US gal)
Rear axle
31 litres (8.2 US gal)
Hydraulic system
Hydraulic oil tank
135 litres (35.7 US gal)
90 litres (23.8 US gal)
Fuel tank
Cooling system
Total
224 litres (59.2 US gal)
30 litres (7.9 US gal)
Oil-bath air cleaner (optional equipment)
38 litres (10.0 US gal)
5.5 litres (14.5 US gal)
L90G
Capacities
When changing
Engine oil, incl. filter
18 litres (4.8 US gal)
Transmission incl. filter
29 litres (7.7 US gal)
Front axle
38 litres (10.0 US gal)
Total
Rear axle
31 litres (8.2 US gal)
135 litres (35.7 US gal)
Hydraulic system
Hydraulic oil tank
90 litres (23.8 US gal)
Fuel tank
Cooling system
Oil-bath air cleaner (optional equipment)
224 litres (59.2 US gal)
30 litres (7.9 US gal)
38 litres (10.0 US gal)
5.5 litres (14.5 US gal)
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Change intervals
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Service capacities and change intervals/Specifications
Change intervals
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
Oil and fluid changes
Hours
Engine 500[T1]
Coolant 6000[T2]
Front and rear axles2000[T3]
Transmission, at the same time clean suction strainer4000
Hydraulic system (working hydraulics, brake system and steering 4000/2000[T4]
system)
Oil-bath air cleaner (optional equipment)250
[T1]Conditions for the engine oil change interval to apply, see page Engine oil.
[T2]Change coolant every 6000 hours or every fourth year. See also page Coolant.
[T3]First change to take place after 1000 hours.
[T4]If the system is filled with mineral hydraulic oil or Volvo Biodegradable Hydraulic Oil 46, the interval is 4000 hours If another
biologically degradable hydraulic oil is used, the interval is 2000 hours.
Filter change
Hours
Engine, oil filters
500[T1]
Engine, air cleaner (primary filter)
1000[T2]
Engine, air cleaner (secondary filter)
2000
Fuel filters, prefilter / water trap
500[T3]
Fuel system, breather filter
2000
Oil-bath air cleaner, cleaning filter insert (optional equipment)
2000
Diesel particle filter, cleaning
6000[T4]
Transmission, oil filter
4000
Axle oil cooling filter (optional equipment)
4000
Drive axles, breather filter
2000
Cab, ventilation filters
2000[T5]
Asbestos filter (optional equipment)
1000
Cab, extra prefilter (optional equipment)
1000
Hydraulic system, return oil filter2000 Hydraulic system, breather filter2000
[T1]Conditions for the engine oil change interval to apply, see page Engine oil.
[T2]Or at signal or at least once a year.
[T3]Or when changing the engine's oil filter, which may mean a shorter interval.
[T4]Cleaning takes place using an exchange system.
[T5]Change the prefilter every 1000 hours.
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Combination table, interchangeable equipment
Information Type:
Operator's Information
Profil e:
Location:
Combination
Specification
s
L70E, L70G Volvo
table,
Date:
11- 08-202 3
interchangeable
equipment/
Combination table, interchangeable equipment
Showing Selected Profile
Valid for serial numbers
Serial number start
ModelProduction site
Serial number stop
L70E, L70G Volvo
The table shows attachments of the category
"interchangeable equipment"*⁾ (attachments that can be changed by the
operator) and for which machines these attachments are approved.
Attachment, type
Attachment,
model
Model/Type
number
Page
Bucket with REF H TB CA 5.2 m³83364 clamping
arm3000 mm
Working
buckets
High-tipping light HIT H BOE 4.8 m³82097
material bucket2650 mm**⁾
High-tipping light HIT H BOE 2.5 m³82098
material bucket2550 mm
High-tipping light HIT H BOE 3.0 m³84464
material bucket2750 mm
High-tipping light HIT H BOE 3.2 m³80963
material bucket2650 mm
High-tipping light HIT H BOE 6.0 m³80964
material bucket2750 mm**⁾
High-tipping light HIT H BOE 3.5 m³84465
material bucket2750 mm
High-tipping light HIT H BOE 3.8 m³82039
material bucket2750 mm
High-tipping light HIT H BOE 7.0 m³82041
material bucket3000 mm**⁾
High-tipping light HIT H BOE 4.5 m³85441
material bucket3000 mm,
side-mounted
cyl inde rs
High-tipping light HIT H BOE 3.8 m³85443
material bucket2750 mm,
side-mounted
cyl inde rs
Pallet forks, Sideshift pallet 83772
sideshift versionforks 1500 mm
Machine
model
Historic
auth ori zation
with L90G
L90F
Working
buckets
with L60G
L60F
Working
buckets
Working
buckets
Working
buckets
Working
buckets
Working
buckets
Working
buckets
Working
buckets
Working
buckets
with L60G
L60F, L70E
with L60G
-
with L70G
L70F
with L70G
L70F
with L70G
-
with L90G
L90E/F
with L90G
L90E/F
with L90G
-
Working
buckets
with L90G
-
Working with pallet L60G, L70G, L90G
forks
L60F, L70F, L90F
FFPSS
Pallet forks, Sideshift pallet 83773Working with pallet L60G, L70G, L90GL60F, L70F, L90F
sideshift versionforks 2000 mm forks
FFPSS
Pallet forks, combi Combi forks 1.1 m²83774Working with pallet L60G, L70GL60F, L70F
forks COF forks
Pallet forks, combi Combi forks 1.6 m²83775Working with pallet L90GL90F
forks COF forks
Log grapple, UNLGR H 1.8 m²80834Timber grapplesL90GL90E/F
unloading1634 mm
Log grapple, UNLGR H 2.4 m²80831Timber grapplesL90GL90E/F
unloading1634 mm
Log grapple, UNLGR H 1.3 m²82194Timber grapplesL60GL60F, L70C/D/E
sorting1620 mm
Log grapple, UNLGR H 1.5 m²80153Timber grapplesL70GL70F
sorting1599 mm
Log grapple, UNLGR H 1.8 m²80835Timber grapplesL90GL90E/F
sorting1634 mm
Log grapple, UNLGR H 2.4 m²80832Timber grapplesL90GL90E/F
sorting1634 mm
Log grapple, UNLGR H 0.7 m²82192Timber grapplesL60GL60F
General Purpose1610 mm
Log grapple, UNLGR H 0.9 m²82028Timber grapplesL70GL70F
General Purpose1600 mm
Log grapple, UNLGR H 1.3 m²82340Timber grapplesL90GL90E/F
General Purpose1200 mm
Log grapple, UNLGR H 1.3 m²82339Timber grapplesL90GL90E/F
General Purpose1635 mm
High-Lift grappleSWC GR 1.5 m²82131Hidden titleL90FL90D/E
High-Lift grappleSWC GR 1.8 m²82132Hidden titleL90FL90D/E
High-Lift grappleSWC GR 2.0 m²82133Hidden titleL90FL90D/E
Material handling MHA H HYDR82137Hidden titleL60F, L70F, L90FL60E, 70D/E, L90D/
armE
*) “interchangeable equipment”(attachments that can be changed by operator) means that the attachment requiresthe
combination hydraulic attachment lock ("hook-on") and quick-couplings for optional hydraulics (3rd and 4th hydraulic
function).
**) Requires installation of two optional highly placed, front-mounted mirrors (optional equipment).
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Coolant
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Recommended lubricants/Specifications
Coolant
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
Only use Volvo Coolant VCS when topping up or changing coolant. To avoid damage to engine and cooling system, different
coolants or corrosion protection must not be mixed.
When using concentrated Volvo Coolant VCS and clean water, the mixture should contain 40–60% concentrated coolant and
60–40% clean water. The amount of concentrated coolant must never be less than 40% of the total mixture, see table below.
Freeze protection down toMixed-in amount of concentrated coolant
-25 °C (-13 °F)40%
-35 °C (-31 °F)50%
-46 °C (-51 °F)60%
The concentrated coolant must not be mixed with water that contains a high degree of lime (hard water), salt or metals.
The clean water for the cooling system must also meet the following requirements:
Description Value
Total number of solid particles< 340 ppm
Total hardness< 9.5° dH
Chloride< 40 ppm
Sulphate< 100 ppm
pH value5.5-9
Silica< 20 mg SiO₂/litre
Iron< 0.10 mg Fe/litre
Manganese< 0.05 mg Mn/litre
Electrical conductivity< 500 µS/cm
Organic material, COD-Mn< 15 mg/litre
If there is any doubt about the water quality use ready-mixed Volvo Coolant VCS, which contains 40% concentrated coolant. Do
not mix with any other ready-mixed coolants since this may result in engine damage.
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Dimensional drawing
Information Type:
Operator's Information
Profil e:
L70E, L70G Volvo
Location:
Dimensions/Specifications
Date:
11- 08-202 3
Dimensional drawing
Showing Selected Profile
Valid for option/configuration
ModelOption no.
L70E, L70G Volvo
Waste handler
Option
Configuration
Waste handler
Installed
Figure1
Specifications and dimensions
Capacity, heaped ISO/SAE
L60G
Pin-on STE/BOE
L70G
Pin-on STE/BOE
L90G
Pin-on STE/BOE
StandardLong boom
StandardLong boom
StandardLong boom
3.1 m³3.1 m³
4.1 m³4.1 m³
4.1 m³4.1 m³
Static tipping load
8690 kg6910 kg
9310 kg7450 kg
12110 kg10230 kg
Fully steered
7510 kg5910 kg
7940 kg6290 kg
10350 kg8680 kg
A
7530 mm8060 mm
7820 mm8280 mm
7860 mm8280 mm
H 45° dump angle
2680 mm3220 mm
2520 mm3020 mm
2640 mm3060 mm
L
5450 mm5970 mm
5620 mm6100 mm
5720 mm6150 mm
M 45° dump angle
1210 mm1210 mm
1390 mm1380 mm
1370 mm1320 mm
T
61 mm98 mm
94 mm101 mm
71 mm75 mm
a1
11780 mm12240 mm
12080 mm12480 mm
12130 mm12450 mm
13085 kg13245 kg
15145 kg15385 kg
16600 kg16840 kg
20.5R25 L5
20.5R25 L5
20.5R25 L5
14000 kg
16500 kg
19000 kg
Machine weight
Ti res
Max.
permitted
weight
machine
Figure2
Specifications and dimensions
Capacity, heaped ISO/SAE
Static tipping load
L110G
Pin-on STE/BOE
L120G
Pin-on STE/BOE
StandardLong boom
StandardLong boom
5.5 m³5.5 m³
5.5 m³5.5 m³
13710 kg11020 kg
14810 kg12080 kg
Fully steered
11760 kg9360 kg
12630 kg10210 kg
A
8370 mm8890 mm
8470 mm8980 mm
H 45° dump angle
2520 mm3070 mm
2580 mm3100 mm
L
6080 mm6590 mm
6150 mm6660 mm
M 45° dump angle
1420 mm1430 mm
1460 mm1430 mm
T
a1
52 mm61 mm
12990 mm13430 mm
57 mm104 mm
13050 mm13490 mm
Machine weight
Ti res
20130 kg20440 kg
20900 kg21100 kg
23.5R25 L5
23.5R25 L5
23000 kg
24000 kg
Max. permitted machine weight
Figure3
L150G
Pin-on STE/BOEPin-on STE/BOEPin-on STE/BOE
L180G
L220G
Specifications and StandardLong StandardLong StandardLong
dimensions boom boom boom
StandardLong
boom
Capacity, heaped ISO/6.8 m³6.8 m³7.8 m³7.8 m³9.5 m³9.5 m³
SAE
Static tipping load18570 kg14950 kg21790 kg17960 kg24200 kg21310 kg
Fully steered16310 kg13030 kg19030 kg15570 kg21170 kg18540 kg
A9100 mm9620 mm9300 mm9780 mm9650 mm9970 mm
H 45° dump angle2650 mm3230 mm2730 mm3230 mm2870 mm3240 mm
L6410 mm6980 mm6630 mm7120 mm7120 mm7480 mm
M 45° dump angle1520 mm1500 mm1580 mm1610 mm1640 mm1620 mm
T49 mm103 mm92 mm174 mm80 mm85 mm
a114890 mm15240 mm15220 mm15520 mm16070 mm16310 mm
Machine weight25760 kg26060 kg28950 kg29230 kg34100 kg34480 kg
Tires26.5R25 L526.5R25 L529.5R25 L5
Max.
permitted
machine weight
28000 kg
31000 kg
L250G
Pin-on STE/BOE
37000 kg
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Electrical system
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Electrical system/Specifications
Electrical system
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
System voltage
24V
Batteries
2 (connected in series)
Battery voltage
12 V
Battery capacity
2 x 170 Ah
Alternator
3135 W / 110 A
Starter motor output
5.5 kW (7 hp)
Battery electrolyte's density kg/dm³
Fully charged battery at +25°C (77°F)
1.275–1.285
Battery should be recharged at density, at +25°C (77°F)
g/l 1.250 g/l
Bulbs
Watt
Socket
Travel lights, low beam
70
PX 26D (H7)
Travel lights, high beam
70
PK 22S (H3)
Parking lights, front
4
BA 9s
Parking lights, rear
10
BA 15s
Brake lights
21
BA 15s
Direction indicators, front
21
BA 15s
Direction indicators, rear
21
BA 15s
Cab lighting
10,
BA 15s
Work lights, front halogen (optional)
21 70
Autoroche, Halogen (H3), Pedestal long
range, Type 500
Work lights, rear halogen (optional)
70
Autoroche, Halogen (H3), Pedestal long
range, Type 500
Guide light in switches
LED
Relays
Figure1
RE
FUNCTION
01
Hydraulic servo, bucket positioner (automatic tilt)14Voltage feed ECC, AC compressor magnetic clutch,
interval coolant pump
02
Front work lights1615A feed
04
Work lights, cab rear1715B feed
06
07
08
09
10
11
12
13
FUNCTION
Reversing light, reversing warning15Windscreen wiper, front
03
05
RE
Hydraulic servo, boom kick-out (automatic lift)1815EA feed, cut-off delay
Starter relay2301Electrically heated fuel filter
Work lights, cab, front2502Power supply, engine
Boom Suspension System, engagement3610Extra set of fuses (optional equipment)
Windscreen wiper, rear3706 and Function relay for electrically controlled battery
3707disconnector (optional equipment)
Brake lights5502Parking brake
Rear work lights8712Water pump, pause heater
30-feed controlled by I-ECU,RE9112Hydraulic valve, adjustable flow 3rd function
hold voltage RE 13
Voltage feed E-ECU, V-ECU, V2-ECU, NOX sensor, RF3601Flash relay
CDC
Relays positioned outside the electrical distribution box
RE FUNCTION
RE
FUNCTION
250
Preheating [1]
370
Battery disconnector
1
Courtesy light [2]
5
Secondary steering [3]
350
640
7
1
3525
Side light [4]
F uses
Figure 2
Fuse
s FU
A
FUNCTION
FU
A
FUNCTION
0
5
Brake lights
1
5
High beam, left
1
15
Work lights cab, front
1
5
15RA feed to voltage converter
0
5
Voltage supply to RE14
1
15
Front work lights
3
2
0
1
4
3
05
5
5
Direction indicators
06
5
Parking light right front, running light right 15
front, parking light left rear, license plate light
15
Work lights, cab rear
07
5
Low beam, left16
15
Rear work lights
08
5
Low beam, right17
10
Voltage supply I-ECU, holding voltage RE13
09
10
Voltage feed RE0218
10
Power socket 24 V
10
5
High beam, right19
15
Headlights
s FU
A
FUNCTION
A
FUNCTION
20
10
5
Working hydraulics
21
10
Voltage feed ignition, electrically controlled 44
battery disconnector
Rotating warning beacon, interior lighting45
5
22
5
Voltage supply to RE1248
5
Directional gear forward/reverse steering
column, Gear selector steering column
Vehicle control unit
23
5
Starter motor voltage feed49
5
Secondary steering
24
25
Voltage feed E-ECU, FU30, FU31, FU2350
5
25
20
5
26
20
Voltage feed V-ECU51
Voltage feed VCADS Pro communication
socket, attachment locking
Ignition-dependent voltage feed
Voltage feed V2-ECU61
15
Fuel filter electric heating
27
20
-
-
28
10
AC compressor magnetic clutch, coolant 64
pump interval heater, ECC
-67
15
Voltage converter
29
5
-70
60
Preheating air [5]
30
5
Preheating relay, VGT-turbo, ACM71
125
Used for secondary steering
31
15
EGR valve, NOX72
125
Cab feed ⁽¹⁾
32
10
BSS Boom Suspension System74
10
Sensing battery voltage, voltage converter
33
10
Regeneration 75
15
[6]
Hood motor ⁽²⁾
34
10
15
Cyclone filter fan
35
10
High and low beams, windscreen wiper and 85
windscreen washer, headlight flasher
-
-
36
5
-
-
37
5
5
Side lights
38
5
15
ACM
39
10
15
Used for the after-treatment system
4
1
5
W-ECU
0
0
5
Reversing camera screen
4
1
1
0
5
Reversing camera activation
4
5
2
43
10
150
Preheater
Instrument lighting, parking light left front, 14
running light left front, parking light right rear
Fuse
FU
Rear window wiper and washer86
Alternator magnetising, fan cyclone filter87
Hazard flashers90
Work lights93
Horn, kick-down, screen reversing camera, 94
electric heating rear-view mirrors, operation of
rear-view mirrors
Optional equipment95
Seat heating, operator's seat load position 98
monitor, ambient temperature
Steering column gear selector, mode selector, 99
differential lock, fully automatic downshifting,
lever support gear selector, Comfort Drive
Control (CDC), Boom Suspension System
activation/function selection
Central lubrication2501
[1]Located to the left on the back of the engine.
[2]Located to the right of the electrical distribution unit
[3]Located inside of the left inner mudguard under the secondary steering pump.
[4]Located to the right of the electrical distribution unit
[5]Located behind the toolbox by the foot board.
[6]Located inside of battery disconnector.
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Engine oil
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Recommended lubricants/Specifications
Engine oil
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
NOTE!
It is very important that instructions for oil grade are followed.
Oil grade
Change intervals (sulphur content in the fuel)
< 15 ppm>15 ppm not permitted
Volvo Engine oil VDS-4.5
every 500 hours
Other approved VDS-4.5 engine oil
Volvo Engine oil VDS-4
Other approved VDS-4 engine oil
API CJ–4 or API CK-4 or ACEA E9
every 250 hours
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Engine
Information Type:
Operator's Information
Profil e:
L70E, L70G Volvo
Location:
Engine/Specifications
Date:
11- 08-202 3
Engine
Showing Selected Profile
Valid for serial numbers
ModelProduction site
L70E, L70G Volvo
L60G
DesigVolvo
natioD6H
n(Tier
4i/
Stage
lllB)
Max.
120
power kW at
1,4001,800
rpm
(23.330.0 r/
s) ISO
9249,
SAE
J1349,
net
Max. 120
power kW
at
1,4001,800
rpm
(23.330.0 r/
s) SAE
J1995,
gross
Max. 820
torqu Nm
e at
1,400
rpm
Serial number start
Serial number stop
(23.3
r/s)
ISO
9249,
SAE
J1349,
net
Max. 820
torqu Nm
e at
1,400
rpm
(23.3
r/s)
SAE
J1995,
gross
Econo 800–
mic 1,600
operarpm
ting (13.3–
range26.6 r/
s)
Numb 6
er of
cylind
ers
Cylind5.7
er litres
capaci(1.5 US
ty gal)
Idle 11.2–
speed12.0 r/
, lows (675–
725
rpm)
Idle 33.8–
speed34.5 r/
, highs
(2030–
2070
rpm)
Air Air
cleane cleanin
rg in 3
steps
Cyclon
e
cleaner
–
pri mar
y filter
–
second
ary
filter
L70G
DesigVolvo
natioD6H
n(Tier
4i/
Stage
lllB)
Max.
126
power kW at
1,4001,700
rpm
(23.328.3 r/
s) ISO
9249,
SAE
J1349,
net
Max. 126
power kW
at
1,4001,700
rpm
(23.328.3 r/
s) SAE
J1995,
gross
Max. 860
torqu Nm
e at
1,400
rpm
(23.3
r/s)
ISO
9249,
SAE
J1349,
net
Max. 860
torqu Nm
e at
1,400
rpm
(23.3
r/s)
SAE
J1995,
gross
Econo 800–
mic 1,600
operarpm
ting (13.3–
range26.6 r/
s)
Numb 6
er of
cylind
ers
Cylind5.7
er litres
capaci(1.5 US
ty gal)
Idle 11.2–
speed12.0 r/s
, low(675–
725
rpm)
Idle 33.8–
speed34.5 r/s
, high(2030–
2070
rpm)
Air Air
cleane cleanin
rg in 3
steps
Cyclon
e
cleaner
–
pri mar
y filter
–
second
ary
filter
L90G
DesigVolvo
natioD6H
n(Tier
4i/
Stage
lllB)
Max.
129
power kW at
1,4001,700
rpm
(23.328.3 r/
s) ISO
9249,
SAE
J1349,
net
Max. 129
power kW
at
1,4001,700
rpm
(23.328.3 r/
s) SAE
J1995,
gross
Max. 880
torqu Nm
e at
1,400
rpm
(23.3
r/s)
ISO
9249,
SAE
J1349,
net
Max. 880
torqu Nm
e at
1,400
rpm
(23.3
r/s)
SAE
J1995,
gross
Econo 800–
mic 1,600
operarpm
ting (13.3–
range26.6 r/
s)
Numb 6
er of
cylind
ers
Cylind5.7
er litres
capaci(1.5 US
ty gal)
Idle 11.2–
speed12.0 r/s
, low(675–
725
rpm)
Idle 33.8–
speed34.5 r/s
, high(2030–
2070
rpm)
Air Air
cleane cleanin
rg in 3
steps
Cyclon
e
cleaner
–
pri mar
y filter
–
second
ary
filter
Printed By - WWW.MANUALLABS.COM
Operator's Information
Document Title:
Fuel
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Fuel system/Specifications
Fuel
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
Fuel recommendations for EU-certified engines (D6H-engines with recirculation of exhausts (EGR) and aftertreatment of
exhausts) for models from year 2011.
Diesel engines from 2011 and later are only intended to be run on sulphur-free fuel, with a maximumsulphur content of 10 ppm.
Using any other fuel than sulphur-free fuel results in an engine with lower efficiency and shorter service life, permanent damage to
advanced emission control devices and systems, inferior fuel economy, and possibly that the engine does not work at all. It is very
likely that the manufacturer's warranties will become invalid and void when using unsuitable orincorrect fuels. Correct selection of
fuel is decisive for good economy, performance, and engine life. Market fuel that meetsEU's standard EN590 for diesel fuel oil
should be used. Swedish Mk1-fuel that meets Swedish SS 155435 is also permitted. It is important that the fuel is not
contaminated by dust or water since these can cause damage to the fuel system and also increase engine wear.
Fuel recommendations for USA-certified engines (D6H-engines with recirculation of exhausts (EGR) and aftertreatment
of exhausts) for models from year 2011.
Diesel engines for model year 2011 and later are designed to only run on fuels with very low sulphur content, Ultra Low Sulphur
Diesel (ULSD), with a maximum sulphur content of 15 ppm. Using any other fuel than ULSD results in an engine with lower
efficiency and shorter service life, permanent damage to advanced emission control devices and systems, inferior fuel economy,
and possibly that the engine does not work at all. It is very likely that the manufacturer's warranties will become invalid and void
when using incorrect fuels, and use of other fuels than ULSD in diesel-powered machines is illegal and punishable by provisions of
civil law and legislation. Correct selection of fuel is decisive for good economy, performance, and engine life. ASTM D 975 Number
2D ULSD should be used when climate conditions permit. ASTM D 975 Number 1D ULSD can be used in cold weather. Mixtures of
ASTM D 975-fuels Number 1D and Number 2D ULSD can be used to suit different climate conditions. It is important that the fuel is
not contaminated by dust or water since these can cause damage to the fuel system and also increase engine w ear.
NOTE!
It is very likely that the manufacturer's warranties will become invalid and void when using unsuitable or incorrect fuels.
NOTE!
If you are unsure of what fuel is in the field tank, do NOT use it in a machine with a D6H-engine.
Bio-diesel fuel
Vegetable oils and/or esters, also called "bio-diesel", (e.g., rape-seed methyl ester, RME fuel) are offered on certain markets both
as pure products and as mixed into the diesel fuel.
Volvo CE accepts max. 7% intermix of bio-diesel fuel in the diesel fuel, ready-mixed from the oil companies.
Operator's Information
Document Title:
Grease
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Recommended lubricants/Specifications
Grease
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
Volvo Super Grease Lithium EP2.
Or corresponding grease on lithium base with EP additives and consistency NLGI class 2.
If the machine is provided with automatic greasing system, other recommended lubricants apply.
Rear axle bearings
Front rear axle bearing:
Axle oil according to recommended lubricants, see page Recommended lubricants.
Rubens HT2 (Q8)
Chevron Ultra Duty No. 2
Texaco Starplex HD2
Almagard 3752
Operator's Information
Document Title:
Hydraulic system
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Hydraulic system/Specifications
Hydraulic system
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Type
Load-sensing, (closed centre)
Hydraulic oil pump, type
Axial piston pump, variable displacement
Pump 1
Does not apply to this machine type
Pump 2
Function
Working hydraulics, steering system, brake system and servo
system
Pump 3
Function
Cooling fan pump and brake system
Loading times:
(with load acc. to ISO 14397 and SAE
J818) Lifting time with load
5.9 s
Lowering time (empty)
3.7 s
Dumping time
2.0 s
Total loading time
11.6 s
L70G
Type
Load-sensing, (closed centre)
Hydraulic oil pump, type
Axial piston pump, variable displacement
Pump 1
Function
Working hydraulics
Pump 2
Function
Working hydraulics, steering system, brake system and servo
system
Pump 3
Function
Cooling fan pump and brake system
Loading times:
(with load acc. to ISO 14397 and SAE
J818) Lifting time with load
6.4 s
Lowering time (empty)
3.3 s
Dumping time
1.8 s
Total loading time
11.5 s
L90G
Type
Load-sensing, (closed centre)
Hydraulic oil pump, type
Axial piston pump, variable displacement
Pump 1
Function
Working hydraulics
Pump 2
Function
Working hydraulics, steering system, brake system and servo
system
Pump 3
Function
Cooling fan pump and brake system
Loading times:
(with load acc. to ISO 14397 and SAE
J818) Lifting time with load
6.4 s
Lowering time (empty)
3.3 s
Dumping time
1.8 s
Total loading time
11.5 s
Operator's Information
Document Title:
Machine capacities
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Machine capacities/Specifications
Machine capacities
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Machine's max. weight, see page Machine weights.
Current machine weight depends on your equipment, see table (last row).
Tires
buckets
Rock 20.5Standard
& Light material
gravel
R25
handling
[T1]
Long
boom
Edge TeethEdge Edge Edge Edge Edge Edge Edge
savers savers savers savers savers savers savers savers
Capacity, 1.9 m³1.8 m³2.1 m³2.1 m³2.3 m³(3 2.3 m³(3 1.7 m³(2.2 3.1 m³(4.1 5 m³(6.5
heaped (2.5 yd³)(2.4 yd³)(2.7 yd³)(2.7 yd³)yd³)yd³)yd³)yd³)yd³)
ISO/ SAE
Capacity 2.1 m³2 m³(2.6 2.3 m³(3 2.3 m³(3 2.5 m³2.5 m³1.9 m³(2.5 3.4 m³(4.4 5.5 m³(7.2 when filled (2.7
yd³)yd³)yd³)yd³)(3.3 yd³)(3.3 yd³)yd³)yd³)yd³)
to 110%
Static 8200 kg8350 kg 8600 kg8100 kg 8510 kg8000 kg7170 kg 7820 kg7800
tipping 18077 lb(18409 18960 lb(17857 18761 lb17637 lb(15807 lb)17240 lb17196 lb
load, lb)lb)15807 lb
straight 18409 lb17857 lb
machine
-1781 kg
-3926 lb
Static 11850 kg11230 kg12170 kg11540 kg11750 kg11140 kg12130 kg10450 kg10510 kg
tipping 26125 lb24758 lb26830 lb25441 lb25904 lb24559 lb26742 lb23038 lb23171 lb
load,
straight
-2450 kg
-5401 lb
Static 732074707700723076207130640069606910
tipping 16138 lb16469 lb16976 lb15939 lb16799 lb15719 lb14110 lb15344 lb15234 lb
load,
turned 35°
-1647
–3631 lb
Static 7060 kg7210 kg7440 kg6970 kg7360 kg6880 kg6180 kg6710 kg6650 kg
tipping 15565 lb15895 lb16402 lb15366 lb16226 lb15168 lb13625 lb14793 lb14661 lb
load, fully
turned
machine
[T2]
-1607 kg
-3543 lb
Breakout 80.2 kN84.2 kN 82.9 kN76.1 kN 79 kN72.9 kN60.2 kN61.7 kN 53.8 kN 9 kN
force(18929 (17108 (13871 lbf)(12095 lbf)
lbf) lbf)
A7370 mm 7490 mm7330 mm7430 mm 7400 mm7500 mm 7690 mm7710 mm7940 mm+522 mm
(2' 5.9'')294.9 in288.6 in(24' 4.5'')291.3 in(24' 7.3'')302.8 in303.5 in312.6 in+21 in
290.2 in292.5 in295.3 in
E1140 mm 1270 mm1110 mm1200 mm1170 mm1260 mm1400 mm1480 mm1700 mm+37
(2' 5.9'')50 in43.7 in47.2 in46 in49,6 in55.1 in58.3 in66.9 in+1.5 in
44.9 in
H[T3] 2800 mm2730 mm 2820 mm2760 mm2780 mm 2710 mm2510 mm2580 mm 2430 mm+539 mm
110.2 in(8' 11.5'')111 in108.7 in(9' 1.4'')106.7 in98.8 in(8' 5.6'')95.7 in+21.2 in
107.5 in109.5 in101.6 in
L5110 mm5110 mm5110 mm5170 mm5190 mm5240 mm4520mm5280 mm5480 mm+516 mm
201.2 in201.2 in201.2 in203.5 in204.3 in206.3 in178 in207.5 in215.7 in+20.3 in
M⁽ ⁾1040 mm 1160 mm 1010 mm1090 mm 1050 mm1130 mm 1130 mm 1320 mm1500 mm -1 mm
(3' 4.9'')(2' 5.9'')39.8 in(2' 5.9'')41.3 in(3' 8.5'')(3' 8.5'')52 in(4' 11.1'')-0.04 in
40.9 in45.7 in42.9 in44.5 in44.5 in59 in
N⁽ ⁾1580 mm1650 mm1570 mm 1610 mm1590 mm 1620 mm1480 mm1620 mm16700 mm+445 mm
62.2 in65 in(5' 1.8'')63.4 in(5' 2.6'')63.8 in58.3 in63.8 in65.7 in+17.5 in
61.8 in62.6 in
V2500 mm 2500 mm 2500 mm 2500 mm 2500 mm 2500 mm 2500 mm 2550 mm 2650 mm
(8' 2.4'')(8' 2.4'')(8' 2.4'')(8' 2.4'')(8' 2.4'')(8' 2.4'')(8' 2.4'')(2' 5.9'')(8' 8.3'')
98.4 in98.4 in98.4 in98.4 in98.4 in98.4 in98.4 in100.4 in104.3 in
a111600 11670 11590 11630 11620 11660 11970 mm11840 mm12060 mm
mm (2' mm (38' mm (38' mm (38' mmmm (38' 471.3 in466.1 in(39' 6.8'')
5.9'')3.4'')0.3'')1.9'')457.5 in3.1'')474.8 in
456.7 in459.4 in456.3 in457.9 in459.1 in
Machine 11960 kg11900 kg11760 kg12000 kg 11800 kg12040 kg11900 kg12090 kg12380 kg+162 kg
weight26367 lb26235 lb25926 lb(26455 26015 lb26544 lb26235 lb26654 lb27293 lb357 lb
lb)
26455 lb
[T1]With L5 tires.
[T2]When the machine is used with a bucket, the max. permitted working load is 50 % of the tipping load for a fully turned
machine. Depending on application and/or machine size the manufacturer often recommends a utilisation lower than 50%.
[T3]Measured to front of bucket tooth or edge savers. Dumping height to edge of bucket (acc. to SAE) + approx. 200 mm (8 in).
Measurement at a dumping angle of 45°. (Spade-nose bucket 42°.)
L70G
Machine's max. weight, see page Machine weights.
Current machine weight depends on your equipment, see table (last row).
Tires Standard buckets
20.5
R25
Capacity
, heaped
ISO/ SAE
Rock &
gravel
handling
[T1]
Edge TeethEdge Edge Edge Edge
savers savers savers savers savers
2.1 m³2 m³(2.6 2.3 m³(3 2.3 m³(3 2.4 m³2.4 m³
(2.7 yd³)yd³)yd³)yd³)(3.1 yd³)(3.1 yd³)
Edge
savers
2.2 m³(2.9
yd³)
Light material
Edge
savers
Edge
savers
3.4 m³
(4.4 yd³)
6.4 m³
(8.4 yd³)
Long
boom
Capacity 2.3 m³(3 2.2 m³2.5 m³2.5 m³2.6 m³2.6 m³2.4 m³(3.1 3.7 m³7 m³(9.1
when yd³)(2.9 yd³)(3.3 yd³)(3.3 yd³)(3.4 yd³)(3.4 yd³)yd³)(4.8 yd³)yd³)
filled to
110%
Static 9210 kg9380 kg9720 kg9130 kg9680 kg9100 kg 7470 kg8740 kg 8300 kg–1856 kg
tipping 20305 lb20679 lb21429 lb20128 lb21341 lb(20062 lb)16469 lb(19158 lb)18298 lb(–3624
load, 20062 lb19268 lblb)
straight -4092 lb
machine
Static 8220 kg8380 kg8700 kg8140 kg8660 kg8110 kg 6630 kg7770 kg7300 kg–1699 kg
tipping 18122 lb18475 lb19180 lb17946 lb19092 lb(17879 lb)14617 lb17130 lb16094 lb(–3624
load, 17880 lblb)
turned –3746 lb
35°
Static 7920 kg8090 kg8400 kg7850 kg 8360 kg 7820 kg6380 kg7480 kg7000 kg-1654 kg
tipping 17461 lb17835 lb18519 lb(17306 lb)(18431 lb)17240 lb14065 lb16491 lb15432 lb3646 lb
load, 17306 lb18431 lb
fully
turned
machine
[T2]
Breakou90.3 kN 94.6 kN95.3 kN86.6 kN93.4 kN85 kN62.7 kN71.8 kN53.9 kN -2 kN
t force(20300 (12117
lbf) lbf)
A7470 mm 7590 mm7420 mm 7530 mm7440 mm7560 mm7950 mm7780 mm8330 mm+464
(24' 6.1'')299 in(24' 4.1'')296 in293 in298 in313 in306 in328 inmm
294 in292 in+18 in
E1180 mm 1290 mm 1120 mm1230 mm1150 mm1250 mm1670 mm1470 mm1970 mm+27 mm
(3' 10.5'')(4' 2.8")44 in48 in45 in49 in66 in58 in78 in+1.1 in
46 in51 in
H[T3] 2760 mm2690 mm2800 mm2720 mm2780 mm 2700 mm2360 mm2530 mm 2150 mm +484
108.7 in105.9 in110.2 in107.1 in(9' 1.4'')106.3 in92.9 in(2' 5.9'')(7' 0.6'')mm
109.4 in99.7 in84.6 in+19.1 in
L5220 mm 5220 mm 5220 mm 5290 mm 5250 mm5320 mm4720 mm5450 mm 5790 mm+473
(17' 1.5'')(17' 1.5'')(17' 1.5'')(17' 4.3'')206.7 in209.5 in185.8 in(17' 10.6'')228 inmm
205.5 in205.5 in205.5 in208.3 in214.6 in+18.6 in
M⁽ ⁾1130 mm 1240 mm 1090 mm 1170 mm1100 mm 1190 mm1340 mm1340 mm1720 mm –22 mm
(3' 8.5'')(4' 0.8'')(2' 5.9'')46.1 in(3' 7.3'')46.9 in52,8 in52,8 in(5' 7.7'')–0.9 in
44.5 in48.8 in42.9 in43.3 in67.7 in
N⁽ ⁾1650 mm1710 mm1620 mm1660 mm1630 mm1670 mm1570 mm 1680 mm 1720 mm +397
65 in67.3 in63.8 in65.4 in64.2 in65.7 in(5' 1.8'')(2' 5.9'')(5' 7.7'')mm
61.8 in66.1 in67.7 in15.6 in
V2550 mm 2550 mm 2550 mm 2550 mm 2550 mm 2550 mm 2650 mm 2650 mm 2750 mm
(2' 5.9'')(2' 5.9'')(2' 5.9'')(2' 5.9'')(2' 5.9'')(2' 5.9'')(8' 8.3'')(8' 8.3'')108,3 in
100.4 in100.4 in100.4 in100.4 in100.4 in100.4 in104.3 in104.3 in
a111690 11760 11660 11720 11680 11730 12320 mm11980 12410
mm (2' mm (38' mm (38' mmmmmm485mm (2' mm (40'
5.9'')7.0'')3.1'')461.4 in459.8 in461.8 in5.9'')8.6'')
460.2 in463 in459.1 in471.7 in588.6 in
Machine 13500 kg13430 kg13290 kg13540 kg13310 kg13560 kg13800 kg13750 kg14290 kg+246 kg
weight29762,4 lb29608.1 29299.4 29850.6 29343.5 29894.7 30423.8 lb30313.5 31504 lb+542.3 lb
lb lb lb lb lb lb
[T1] With L5 tires.
[T2]When the machine is used with a bucket, the max. permitted working load is 50 % of the tipping load for a fully turned machine.
Depending on application and/or machine size the manufacturer often recommends a utilisation lower than 50%.
[T3]Measured to front of bucket tooth or edge savers. Dumping height to edge of bucket (acc. to SAE) + approx. 200 mm (8 in).
Measurement at a dumping angle of 45°. (Spade-nose bucket 42°.)
L90G
Machine's max. weight, see page Machine weights.
Current machine weight depends on your equipment, see table (last row).
[T1]
Tires Standard bucketsRock &
20.5 gravel
R25 handling
Edge TeethEdge Edge Edge Edge Edge
savers savers savers savers savers savers
Capacity2.3 m³2.5 m³(3.3 2.5 m³(3.3 2.5 m³(3.3 2.6 m³2.8 m³2.8 m³(3.7
, heaped (3.0 yd³)yd³)yd³)yd³)(3.4 yd³)(3.7 yd³)yd³)
ISO/ SAE
Capacity 2.5 m³(3.7 2.8 m³2.8 m³2.8 m³2.9 m³3.1 m³3.1 m³(4.1 when yd³)(3.7 yd³)(3.7 yd³)(3.7
yd³)(3.8 yd³)(4.1 yd³)yd³)
filled to
110%
Light material
Edge
savers
Edge
savers
4.1 m³
(5.4 yd³)
7 m³(9.2
yd³)
4.5 m³
Long
boom
7.7 m³
(5.9 yd³)
(10.1 yd³)
Static 10670 kg10710 kg11180 kg10490 kg10520 kg11150 kg10400 kg
tipping 23523.3 lb23611.5 24647.7 23126.5 23192.6 24581.5 22928.1 lb
load, lblblblblb
straight
machine
10100 kg
22266.7
lb
9800 kg
21605,3
lb
–1779 kg
-3922 lb
Static 9430 kg9460 kg9910 kg9260 kg9280 kg9880 kg9160 kg
tipping 20789.6 lb20855.7 21847.8 20414.8 20458.9 21781.7 20194.3 lb
load, lblblblblb
turned
35°
8880 kg
19577
lb
8570 kg
18893.6
lb
–1623 kg
3578.1
lb
8520 kg
18783.4
lb
8200 kg
18077.9
lb
-1578 kg
3478.9
lb
Static 9060 kg9100 kg9530 kg8900 kg8910 kg9500 kg8800 kg
tipping 19973.9 lb20062 lb21010 lb19621.1 19643.2 20943.9 19400.7 lb
load, lblblb
fully
turned
machine
[T2]
Breakou134.9 kN134 kN141.3 kN129.5 kN127 kN135.5 kN124.7 kN
t force
A7590 mm7860 mm7540 mm 7650 mm 7680 mm7600 mm 7710 mm
298.8 in309.5 in(24' 8.8'')(25' 1.2'')302.4 in(24' 303.5 in
296.8 in301.2 in11.2'')
299.2 in
E1200 mm1430 mm1150 mm1250 mm1270 mm1200 mm1300 mm
47.2 in56.3 in45.3 in49.2 in50 in47.2 in51.2 in
H[T3] 2820 mm2650 mm 2860 mm2780 mm 2760 mm2820 mm2740 mm
111 in(8' 8.3'')112.6 in(9' 1.4'')108.7 in111 in107,9 in
104.3 in109.5 in
L5380 mm 5460 mm 5380 mm 5440 mm5460 mm 5430 mm 5490 mm
(17' 7.8'')(17' (17' 7.8'')214,2 in(17' 11.0'')(17' 9.7'')(18' 0.1'')
100.6 kN87 kN-2
8040 mm8350 mm+411
316.5 in328.7 inmm
+16.2 in
1600 mm1860 mm–8 mm
63 in73.2 in+0.3 in
2530 mm 2330 mm+435
(2' 5.9'')91.7 inmm
99.6 in+17.1 in
5560 mm 5770mm+425 (18'
2.9'')227,2 inmm
211.8 in11.0'')211.8 in215 in213.8 in216.1 in218.9 in+16.7 in
215 in
M⁽ ⁾1120 mm1310 mm 1090 mm 1160 mm 1180 mm 1120 mm1200 mm1470 mm1670 mm–32 mm
44.1 in(4' 3.6'')(2' 5.9'')(2' 5.9'')(3' 10.5'')44 in47.2 in57.9 in65.7 in–1.3 in
51.6 in42.9 in45.7 in46.5 in
N⁽ ⁾1700 mm1770 mm1670 mm1710 mm1720 mm 1690 mm1730 mm1740 mm1730 mm+363
66.9 in69,7 in65.7 in67.3 in(5' 7.7'')66.5 in68.1 in68.5 in68.1 inmm
67.7 in14.3 in
V2650 mm2650 mm2650 mm2650 mm2650 mm2750 mm2750 mm2750 mm3000 mm
104.3 in104.3 in104.3 in104.3 in104.3 in108,3 in108,3 in108,3 in118.1 in
a111860 12000 11840 11890 11900 11950 12010 mm 12200 12600
mm (38' mm (39' mmmmmmmm(397' 4.8'')mm (40' mm (41'
10.9'')4.4'')466.1 in468.1 in468.5 in470.5 in472,80.3'')4.1'')
466.9 in472.4 in480.3 in496.1 in
Machine 15220 kg 15220 kg 15040 kg15270 kg15310 kg15020 kg15390 kg15510 kg15940 kg+246 kg
weight(33554 lb)(33554 lb)592,1 lb601,2 lb602,8 lb591,3 lb605,9 lb610,6 lb627,6 lb+9,7 lb
599,2 lb599,2 lb
[T1]With L5 tires.
[T2]When the machine is used with a bucket, the max. permitted working load is 50 % of the tipping load for a fully turned
machine. Depending on application and/or machine size the manufacturer often recommends a utilisation lower than 50%.
[T3]Measured to front of bucket tooth or edge savers. Dumping height to edge of bucket (acc. to SAE) + approx. 200 mm (8 in).
Measurement at a dumping angle of 45°. (Spade-nose bucket 42°.)
Operator's Information
Document Title:
Machine weights
Information Type:
Operator's Information
Date:
11- 08-202 3
Profile
L70E,
L70G Volvo
:
Location:
Machine weights/Specifications
Machine weights
Showing Selected Profile
Valid for serial numbers
ModelProduction site
L70G Volvo
L60G
Operating
13,60
weight
0 kg
The (135,8
operating 05
weight is lbs)
the (2998
machine's 3 lb)
most
common
configurati
on + 10%.
The
machine's
most
common
configurati
on
includes:
B
u
ck
et
(p
in
o
n)
4.
0
m
³
(
5.
2
y
Serial number start
Serial number stop
Ti
St
O
or
d³
)
re
s
2
0.
5
R
2
5
L
3
a
n
d
ar
d
b
o
o
m
p
er
at
a
n
d
al
l
fl
ui
d
s
Max. 14500
machine kg
weight (31,96
Max. 7 lbs)
machine
weight
(incl.
equipment
and
attachmen
t) [1]
L70G
Operating
15,60
weight
0 kg
The (135,8
operating 05
weight is lbs)
the
(34,39
machine's 2 lbs)
most
common
configurati
on + 10%.
The
machine's
most
common
configurati
on
includes:
B
ck
et
(p
n)
.3
u
in
o
4.
8
m
³
(6
y
d³
)
Ti
re
St
m
ft
s
2
0.
5
R
2
5
L
3
a
n
d
ar
d
b
o
o
(li
ar
m
O
or
s)
p
er
at
a
n
d
al
l
fl
ui
d
s
Max. 16,50
machine 0 kg
weight (135,8
Max. 05
machine lbs)
weight (36,37
(incl. 6 lbs)
equipment
and
attachmen
t) ⁽¹⁾
L90G
Operating
17,30
weight
0 kg
The (135,8
operating 05
weight is lbs)
the (38,14
machine's 0 lbs)
most
common
configurati
on + 10%.
The
machine's
most
common
configurati
on
includes:
B
u
ck
et
(p
in
o
n)
4.
8
m
³
(6
.3
y
d³
)
Ti
re
s
2
0.
5
R
2
5
L
3
St
a
n
d
ar
d
b
o
o
m
(li
ft
ar
m
s)
O
p
er
at
or
a
n
d
al
l
fl
ui
d
s
19000
kg
Max.
(4188
machine8 lb)
weight
Max.
machine
weight
(incl.
equipment
and
attachmen
t) ⁽¹⁾
[1]The machine is designed for a maximum machine weight acc. to the table. The max. weight applies when the machine is
equipped for certain applications approved by Volvo. Safety will be jeopardized if the max. weight is exceeded. In addition, no
manufacturer warranties are valid. However, always pay attention to national regulations for travelling on public roads.
Operator's Information
Document Title:
Material handling arm
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Material handling arm/Specifications
Material handling arm
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
L70E, L70G Volvo
L60G
Attachment
Hook-on
Order no.
92007
Weight
500 kg (1102.3
Ti res
lbs) 20.5R25 L3
Serial number stop
Figure1
D
2590 mm (102. in)
J
900 mm (35.4 in)
P
1510 mm (59. in)
E
2000 mm (78. in)
K
1220 mm (48. in)
Q
5290 mm (208. in)
F
1460 mm (57.5 in)
L
1580 mm (62. in)
R
6170 mm (242. in)
G
3270 mm (128. in)
M
2260 mm (89. in)
S
7140 mm (281. in)
H
4300 mm (169. in)
N
3240 mm (127. in)
I
5430 mm (213. in)
O
4320 mm (155. in)
Loading table for material handling arm
Arm extension
Retracted (A)
1800 kg (3968.
Half extended (B)
lbs)
Fully extended (C)
(3086. lbs) 1150
L70G
1400
kg (2535. lbs)
Attachment
Hook-on
Order no.
92007
Weight
500 kg (1102.3
Ti res
lbs) 20.5R25 L3
kg
Figure2
D
2710 mm (106. in)
J
1 260 mm (49.6 in)
P
1530 mm (60. in)
E
2100 mm (82. in)
K
1740 mm (68. in)
Q
5300 mm (208. in)
F
1540 mm (60. in)
L
2260 mm (89. in)
R
6180 mm (243. in)
G
3320 mm (130. in)
M
2170 mm (85. in)
S
7130 mm (280. in)
H
4350 mm (171.3 in)
N
3090 mm (121. in)
I
5490 mm (216.1 in)
O
4100 mm (161. in)
Loading table for material handling arm
Arm extension
Retracted (A)
2150 kg (4739. lbs)
Half extended (B)
1710 kg (3769. lbs)
Fully extended (C)
1400 kg (3086. lbs)
L90G
Attachment
Hook-on
Order no.
92007
Weight
500 kg (1102.3 lbs)
Ti res
20.5R25 L3
Figure3
D
2630 mm (103.5 in)
J
1360 mm (53. in)
P
1540 mm (60. in)
E
2030 mm (87. in)
K
1910 mm (75. in)
Q
5340 mm (210. in)
F
1430 mm (56.3 in)
L
2460 mm (96. in)
R
6300 mm (248. in)
G
3270 mm (128. in)
M
2040 mm (80. in)
S
7260 mm (285. in)
H
4410 mm (173. in)
N
3030 mm (119. in)
I
5540 mm (218. in)
O
4020 mm (158. in)
Loading table for material handling arm
Arm extension
Retracted (A)
2760 kg (6084. lbs)
Half extended (B)
2130 kg (4695. lbs)
Fully extended (C)
1740 kg (3836. lbs)
Operator's Information
Document Title:
Pallet forks
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Pallet forks/Specifications
Pallet forks
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Pallet fork (with attachment bracket)
Attachment
Hook-on
Order no.
83768
Ti res
20.5R25 L3
Figure1
A
790 mm (31.1 in)
C
–37 mm (–1.5 in)
E
3710 mm (146.0 in)
B
1560 mm (61.4 in)
D
1830 mm (72.0 in)
F
700 mm (27.6 in)
Loading table for pallet forks
Rated operating load capacity (rated work load) at different load centre distances
Ground
Tires
500 mm 600 mm 700 mm 800 mm 900 mm 1200 mm
(19.7 in)(23.6 in)(27.6 in)(31.5 in)(35.4 in)(47.2 in)
Rough terrain
20.5R25
5350 kg 5150 kg 5000 kg 4850 kg 4700 kg 4300 kg (11794.7 lbs)(11353.8 lbs)(11023 lbs)
(10692.4 lbs)(10361.7 lbs)(9479.9 lbs)*
Even and hard20.5R257050 kg 6800 kg 6600 kg 6400 kg 5700 kg 4300 kg
(15542.6 lbs)(14991.4 lbs)(14550.5 lbs)(14109.6 lb)*(12566.3 lb)*(9479.9 lbs)*
The maximum permitted load according to the table is reduced if the attachments are supplemented with optional equipment.
For more information, contact your dealer who has access to the attachment catalogue.
*) Is limited by the attachment. (max. load per arm, 4300 kg (9479.9 lbs) at 600 mm (23.6 in) TP-distance).
L70G
Pallet fork (with attachment bracket)
Attachment
Hook-on
Order no.
83768
Ti res
20.5R25 L3
Figure2
A
840 mm (33.1 in)
C
–55 mm (–2.2 in)
E
3740 mm (147.2 in)
B
1610 mm (63.4 in)
D
1860 mm (73.2 in)
F
760 mm (29.9 in)
Loading table for pallet forks
Rated operating load capacity (rated work load) at different load centre distances
Ground
Tires
500 mm 600 mm 700 mm 800 mm 900 mm 1200 mm
(19.7 in)(23.6 in)(27.6 in)(31.5 in)(35.4 in)(47.2 in)
Rough terrain
20.5R25
5890 kg 5670 kg 5530 kg 5360 kg 5210 kg 4300 kg (12985.2 lbs)(12500.2 lbs)(12191.6 lbs)
(11816.8 lbs)(11486.1 lbs)(9479.9 lbs)*
Even and hard20.5R257780 kg 7500 kg 7310 kg 6450 kg 5730 kg 4300 kg
(17152.0 lbs)(16534.7 lbs)(16115.8 lbs)(14220.0 lb)*(12632.5 lb)*(9479.9 lbs)*
The maximum permitted load according to the table is reduced if the attachments are supplemented with optional equipment.
For more information, contact your dealer who has access to the attachment catalogue.
*) Is limited by the attachment. (max. load per arm, 4300 kg (9479.9 lbs) at 600 mm (23.6 in) TP-distance).
L90G
Pallet fork (with attachment bracket)
Attachment
Hook-on
Order no.
83768
Ti res
20.5R25 L3
Figure3
A
940 mm (37.0 in)
C
42 mm (1.7 in)
E
3730 mm (146.9 in)
B
1690 mm (66.5 in)
D
1750 mm (68.9 in)
F
750 mm (29.5 in)
Loading table for pallet forks
Rated operating load capacity (rated work load) at different load centre distances
Ground
Tires
500 mm 600 mm 700 mm 800 mm 900 mm 1200 mm
(19.7 in)(23.6 in)(27.6 in)(31.5 in)(35.4 in)(47.2 in)
Rough terrain
20.5R25
5890 kg 5670 kg 5530 kg 5360 kg 5210 kg 4300 kg (12985.2 lbs)(12500.2 lbs)(12191.6 lbs)
(11816.8 lbs)(11486.1 lbs)(9479.9 lbs)*
Even and hard20.5R257780 kg 7500 kg 7310 kg 6450 kg 5730 kg 4300 kg
(17152.0 lbs)(16534.7 lbs)(16115.8 lbs)(14220.0 lb)*(12632.5 lb)*(9479.9 lbs)*
The maximum permitted load according to the table is reduced if the attachments are supplemented with optional equipment.
For more information, contact your dealer who has access to the attachment catalogue.
*) Is limited by the attachment. (max. load per arm, 4300 kg (9479.9 lbs) at 600 mm (23.6 in) TP-distance).
Operator's Information
Document Title:
Recommended lubricants
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Recommended lubricants/Specifications
Recommended lubricants
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
For questions about oils, lubricants, and extreme outdoor temperatures, contact your dealer for more information.
NOTE!
Keep in mind the type of engine with which the machine is equipped and follow the instructions thatapply to that engine.
NOTE!
It is very important that instructions for oil grade are followed, otherwise deposits from the oil may clog the particle filter.
Oil gradeRecommended viscosity at different ambient temperatures Volvo Ultra Diesel Engine
ENGINE
Oil
VDS-4 or other approved VDS-4
engine oil
Figure1
ACEA–E9
API:CJ-4
Follow
recommended
change
intervals according to the oil's grade
(quality class) and sulphur content
in the fuel.
Follow recommended change intervals according to the oil's grade (quality class).
Oil gradeSulphur content in fuel, in ppm
< 15 ppm
> 15 ppm is not allowed.
Oil change interval
Volvo Ultra Diesel Engine Oil VDS-4
500
ACEA: E9
API: CJ–4
hours
250
hours
Oil gradeRecommended viscosity at different ambient temperatures Volvo Super Wet Brake
AXLES
Transaxle
Oil
Volvo WB 101[1]
Volvo WB 102[2]
Figure2
TRANSMISSI
ON
Volvo Automatic Transmission
Fluid AT102
Figure3
HYDRAULIC
SYSTEM
Volvo Super Hydraulic Oil
Available as an alternative there
is also
Volvo Biodegradable Hydraulic
Oil 46.
For more information, contact your
local Volvo dealer.
Figure4
COOLING
SYSTEM
Volvo Coolant VCS
See page Coolant
information.
[1] Change interval 1000 h
[2] Change interval 2000 h
for
more
Operator's Information
Document Title:
Service history
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Service history/Specifications
Service history
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
Service 500
Type of service
Hours
hours
Signature and stamp
Service and maintenance
Date
Service
1000
Type of service
Hours
hours Date
Signature and stamp
First 1000 hours
Service and maintenance
Service
1500
hours Date
Service
2000
2500
Service
hours Date
3000
Signature and stamp
Service and maintenance
Type of service
Hours
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Service
Type of service
Hours
Service and maintenance
Signature and stamp
Service
3500
Hours
hours Date
Service
4000
4500
Service
5000
Service
5500
Service
6000
Service
6500
Service
7000
Service
7500
hours Date
Service 8000 hours
Signature and stamp
Service and maintenance
Type of service
Hours
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Service
Type of service
Signature and stamp
Service and maintenance
Type of service
Signature and stamp
Date
Service
Hours
8500
Service
9000
9500
Service
10000
Service
10500
Service
11000
Service
11500
hours Date
Service
hours Date
12000
Signature and stamp
Service and maintenance
Type of service
Hours
Signature and stamp
Service and maintenance
Type of service
Hours
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Signature and stamp
Service and maintenance
Type of service
Hours
hours Date
Service
Type of service
Hours
hours Date
Service and maintenance
Service and maintenance
Signature and stamp
Operator's Information
Document Title:
Steering system
Information Type:
Operator's Information
Profil e:
L70E, L70G Volvo
Location:
Steering/Specifications
Date:
11- 08-202 3
Steering system
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Type
Load-sensing, hydrostatic
Number of steering wheel revolutions, total
4.3 revolutions
Steering angle
±40°
Steering pump
Common with working hydraulics
L70G
Type
Load-sensing, hydrostatic
Number of steering wheel revolutions, total
4.3 revolutions
Steering angle
±40°
Steering pump
Common with working hydraulics
L90G
Type
Load-sensing, hydrostatic
Number of steering wheel revolutions, total
4.3 revolutions
Steering angle
±40°
Steering pump
Common with working hydraulics
Operator's Information
Document Title:
Timber grapples
Information Type:
Operator's Information
Date:
11- 08-202 3
Profil e:
L70E, L70G Volvo
Location:
Timber grapples/Specifications
Timber grapples
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Log grapple (for attachment bracket)
Attachment
Hook-on
Ti res
20,5 R25 L3
A
1.3 m²(2015.0 in²)
Figure1
B
3410 mm (134.3 in)
F
1530 mm (60.2 in)
J
2000 mm (78.7 in)
C
1480 mm (58.3 in)
G
2350 mm (92.5 in)
K
2080 mm (81.9 in)
D
2930 mm (115.4 in)
H
4330 mm (170.5 in)
L
1710 mm (67.3 in)
E
1170 mm (46.1 in)
I
5880 mm (231.5 in)
M
7890 mm (310.6 in)
L70G
Log grapple (for attachment bracket)
Attachment
Hook-on
Ti res
20,5 R25 L3
A
1.5 m²(2325.0 in²)
Figure2
B
3390 mm (133.5 in)
F
1510 mm (59.4 in)
J
2140 mm (84.3 in)
C
1590 mm (62.6 in)
G
2440 mm (96.1 in)
K
2370 mm (93.3 in)
D
2870 mm (113.0 in)
H
4380 mm (172.4 in)
L
1790 mm (70.5 in)
E
1 260 mm (49.6 in)
I
6030 mm (237.4 in)
M
7990 mm (314.6 in)
L90G
Log grapple (for attachment bracket)
Attachment
Hook-on
Ti res
20,5 R25 L3
A
2.4 m²(3720.0 in²)
Figure 3
B
3420 mm (134.6 in)
F
1440 mm (56.7 in)
J
2790 mm (109.8 in)
C
1820 mm (71.7 in)
G
2760 mm (108.7 in)
K
2990 mm (117.7 in)
D
2800 mm (110.2 in)
H
4540 mm (178. in)
L
2150 mm (84.6 in)
E
1430 mm (56.3 in)
I
6590 mm (259. in)
M
8460 mm (333. in)
Operator's Information
Document Title:
Transmission
Information Type:
Operator's Information
Profil e:
Location:
Transmission/Specifications
L70E, L70G Volvo
Date:
11- 08-202 3
Transmission
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
Hydraulic transmission
Make
Volvo
Type
Full power shift transmission
Designation
HTE 125
Torque converter
Single stage
Torque multiplication
2.45:1
Number of gears
4 forward, 4 reverse
Gearshifting system
Electro-hydraulic with APS (Automatic Power Shift)
Values
Speed range
(tires 20,5R25L3)
1st0–6.5 km/h (0–4.0 mph)
2nd0–12.5 km/h (0–7.7 mph)
3rd0–26.0 km/h (0–16.1 mph)
4th0–38.0 km/h (0–23.6 mph)
L70G
Hydraulic transmission
Make
Volvo
Type
Full power shift transmission
Designation
HTE 125
Torque converter
Single stage
Torque multiplication
2,45:1
Number of gears
4 forward, 4 reverse
Gearshifting system
Electro-hydraulic with APS (Automatic Power Shift)
Values
Speed range
(tires 20,5R25L3)
1st0–7.0 km/h (0–4.3 mph)
2nd0–12.5 km/h (0–7.7 mph)
3rd0–25.0 km/h (0–15.5 mph)
4th0–38.0 km/h (0–23.6 mph)
L90G
Hydraulic transmission
Make
Volvo
Type
Full power shift transmission
Designation
HTE 125
Torque converter
Single stage
Torque multiplication
2,45:1
Number of gears
4 forward, 4 reverse
Gearshifting system
Electro-hydraulic with APS (Automatic Power Shift)
Values
Speed range
(tires 20,5R25L3)
1st0–7.0 km/h (0–4.3 mph)
2nd0–12.5 km/h (0–7.7 mph)
3rd0–25.0 km/h (0–15.5 mph)
4th0–38.0 km/h (0–23.6 mph)
Operator's Information
Document Title:
Tyre sizes and pressures
Information Type:
Operator's Information
Profil e:
L70E, L70G Volvo
Location:
Wheels/Specifications
Date:
11- 08-202 3
Tyre sizes and pressures
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
L60G
If other tires are used than those stated, the tire manufacturer should be contacted for information about the correct tire pressure.
All tires in the table are not available on all markets. Contact your dealer for more information.
Tires
Bridgestone VMT 17.5R25kPa
psi
Material handling
Loading work 10 km/h
Material handling Load/Log handling
Carry, max. 25 km/h (15.5
mph)
Front Rear
Front Rear Front Rear
-
-
-
-
350
51
250
36
20
350
51
250
36
5
47
32
0
29
20
-
-
0
29
20
5
47
32
0
29
20
350
51
-
350
51
-
-
-
5
47
32
0
29
20
5
47
32
0
29
20
-
-
5
47
45
0
29
30
5
47
45
0
29
30
-
-
-
-
0
65
45
0
44
30
0
65
45
0
44
30
350
51
-
250
36
-
0
65
45
0
44
30
0
65
45
0
44
30
0
0
0
0
45
0
65
30
0
44
45
0
65
30
0
44
psi
45
30
45
30
psi
0
65
0
44
0
65
0
44
32
20
32
5
47
32
0
29
20
5
47
32
Bridgestone VSW 17.5R25*kPa
Bridgestone VMT 20.5R25*kPa
Bridgestone VSW 20.5R25*kPa
psi
Bridgestone VSDL 20.5R25*kPa
psi
Bridgestone VJT 20.5R25*kPa
psi
Firestone SGG 17.5-25/12 kPa
PR psi
Firestone SRG 17.5-25/16 PRkPa
psi
Goodyear GP2B 17.5R25*kPa
psi
Goodyear RL-2+ 17.5R25*kPa
psi
Goodyear HRL 20.5R25/16kPa
psi
Goodyear TL-3A+ 20.5R25kPa
psi
Goodyear RL-5K 20.5R25kPa
psi
47
29
47
29
psi
325
47
200
29
325
47
200
29
325
47
325
47
300
44
400
58
400
58
250
36
200
29
200
29
200
29
250
36
250
36
200
29
325
47
325
47
300
44
400
58
400
58
250
36
200
29
200
29
200
29
250
36
250
36
200
29
250
36
200
29
250
36
200
29
250
36
250
200
29
200
250
36
250
200
29
200
36
325
47
29
200
29
36
325
47
29
200
29
Goodyear GP2B 20.5R25*kPa
Goodyear GP4B 20.5R25*kPa
psi
Goodyear RL2+ 20.5R25*kPa
psi
Goodyear GP3D 600/65R25kPa
psi
Michelin SNOPLUS 17.5R25*kPa
psi
Michelin XHA 17.5R25*kPa
psi
Michelin SNOPLUS 20.5R25*kPa
psi
Michelin XHA 20.5R25*kPa
psi
Michelin X-MINE D2 kPa
20.5R25* psi
Michelin XLD 600/65R25*kPa
psi
Yokohama RB31 20.5R25*kPa
psi
35
0
51
25
0
36
35
25
0
51
0
36
35
25
0
51
35
0
36
25
0
51
-
0
36
-
-
-
30
25
0
44
30
0
36
25
0
0
44
36
The recommended tire pressures are based on the rated load for each handling case.
In case of heavier loads, especially during log handling or load/carry operations, a higher tire pressure is required.
Contact the tire manufacturer's dealer for information about which air pressure is correct
30 for the load25that is to be
handled and for the transport distance in question.
If L4 or L5 tires are used for load/carry operations, pay attention to the transport distances.0 Radial tires are0 preferred for
load/carry operations since there is less heat build-up in this type of tire.
44
36
L70G
35
25
0
51
0
36
If other tires are used than those stated, the tire manufacturer should be contacted for information about the correct tire pressure.
All tires in the table are not available on all markets. Contact your dealer for more information.
Tires
Bridgestone VMT 20.5R25*kPa
psi
Material handling Load/Log handling
Carry, max. 25 km/h (15.5
mph)
Front Rear
Front Rear Front Rear
35
0
51
20
0
29
35
0
51
20
0
29
37
5
54
25
0
36
psi
35
20
35
20
37
25
psi
0
51
0
29
0
51
0
29
5
54
0
36
35
20
35
20
37
25
0
51
35
0
29
20
0
51
35
0
29
20
5
54
-
0
36
-
0
51
35
0
29
27
0
51
35
0
29
27
-
-
Bridgestone VSW 20.5R25*kPa
Bridgestone VJT 20.5R25*kPa
Bridgestone VSDL 20.5R25*kPa
psi
Goodyear GP-2B 20.5/16 kPa
HRL* psi
Material handling
Loading work 10 km/h
Goodyear GP-2B 20.5R25*kPa
psi
35
0
51
22
5
33
35
0
51
22
5
33
37
5
54
25
0
36
psi
35
22
35
22
37
25
psi
0
51
5
33
0
51
5
33
5
54
0
36
35
22
35
22
37
25
0
51
35
5
33
22
0
51
35
5
33
22
5
54
37
0
36
25
0
51
35
5
33
22
0
51
35
5
33
22
5
54
-
0
36
-
0
51
32
5
33
20
0
51
32
5
33
20
35
25
5
47
30
0
29
20
5
47
30
0
29
20
0
51
35
0
36
25
0
51
35
0
36
25
Goodyear GP-4B 20.5R25*kPa
Goodyear RL2+ 20.5R25*kPa
Good Year TL-3A+ 20.5R25*kPa
psi
Good Year RL-5K 20.5R25*kPa
psi
Goodyear GP-3D 600/65R25kPa
psi
Michelin SNOPLUS 20.5R25*kPa
psi
Michelin XHA 20.5R25*kPa
psi
Michelin X-MINE D2 kPa
20.5R25* psi
Michelin XLD 600/65R25*kPa
psi
Yokohama RB31 20.5R25*kPa
psi
L90G
0
0
0
0
44
29
44
29
30
20
30
20
0
0
The recommended tire pressures are based on the rated load for each handling case.
51
36is required.
In case of heavier loads, especially during log handling or load/carry operations, a higher tire pressure
0
0
0
0
Contact the tire manufacturer's dealer for information about which air pressure is correct for the load- that is to be
44
29
44
29
handled and for the transport distance in question.
30
20
30
20 distances. Radial tires are preferred for
If L4 or L5 tires are used for load/carry operations, pay attention to the transport
32
25
load/carry operations since there is less heat build-up in this type of tire.
0
0
0
0
5
0
44
29
44
29
47
36
30
20
30
20
37
25
0
0
0
0
5
0
If other tires are used than those stated,
should 44
be contacted for
44the tire manufacturer
29
29information about the correct tire pressure.
54
36
All tires in the table are not available on35
all markets. Contact
for more information.
22 your dealer35
22
Tires
Bridgestone VSW 20,5R25
Bridgestone VMT 20,5R25
Bridgestone VJT 20,5R25
Bridgestone VSDL 20,5R25
Bridgestone VTS 650/65R25
Goodyear RL2+ 20,5R25
0
5
Material handling
51
33 km/h
Loading
work 10
0
5 Load/Log handling
Material handling
51
Carry,
max. 2533km/h (15.5
Front Rear
Front Rear Front Rear
mph)
kP
a
psi
40
0
58
25
0
36
40
0
58
25
0
36
45
0
65
35
0
51
kP
40
25
40
25
45
35
a
psi
0
58
0
36
0
58
0
36
0
65
0
51
kP
40
25
40
25
45
35
a
psi
kP
0
58
40
0
36
25
0
58
40
0
36
25
0
65
-
0
51
-
a
psi
kP
0
58
35
0
36
25
0
58
35
0
36
25
45
30
0
65
0
44
psi
58
36
58
36
65
51
Goodyear GP2B 20,5R25
kP
Goodyear GP4B 20,5R25
a
psi
400
58
250
36
400
58
250
36
450
65
350
51
400
58
400
250
36
250
400
58
400
250
36
250
450
65
450
350
51
350
58
400
58
350
51
36
250
36
225
33
58
400
58
350
51
36
250
36
225
33
65
-
51
-
-
-
350
51
250
36
350
51
250
36
450
65
300
44
325
47
325
225
33
225
325
47
325
225
33
225
350
51
350
250
36
250
47
325
33
225
47
325
33
225
51
-
36
-
47
300
33
200
47
300
33
200
400
250
44
29
44
29
58
36
400
250
400
250
450
350
Goodyear TL-3A+ 20,5R25
Goodyear RL-5K 20,5R25
Goodyear 20,5R25/16 HRL
Goodyear GP3D 650/65R25
Michelin XHA 20,5R25
Michelin SNOPLUS 20.5R25
Michelin XMINE D2 20,5R25
Michelin XLD 650/65R25
Yokohama 20,5R25 RB31
kP
a
psi
kP
a
psi
kP
a
psi
kP
a
psi
kP
a
psi
kP
58
36
58
36
65
51
a
psi
kP
The recommended tire pressures are based on the rated load for each handling case.
a
In case of heavier loads,
especially during log handling or load/carry operations, a higher tire pressure is required.
Contact the tire manufacturer's
dealer for information about which air pressure is correct for the load that is to be
psi
handled and for the transport
distance
in question.
kP
If L4 or L5 tires are used for load/carry operations, pay attention to the transport distances. Radial tires are preferred for
load/carry operations asince there is less heat build-up in this type of tire.
psi
kP
a
psi
kP
a
psi
Operator's Information
Document Title:
Wheel nuts, tightening torque
Information Type:
Operator's Information
Profil e:
L70E, L70G Volvo
Location:
Wheels/Specifications
Date:
11- 08-202 3
Wheel nuts, tightening torque
Showing Selected Profile
Valid for serial numbers
ModelProduction site
Serial number start
Serial number stop
L70E, L70G Volvo
Wheel nuts, tightening torque
600 ±50 Nm (443 ±37 lbf ft)
Printed By - WWW.MANUALLABS.COM