PRODUCT FAMILY DATA SHEET
XLamp® XP-E2 Torch LEDs
PRODUCT DESCRIPTION
FEATURES
TABLE OF CONTENTS
The XLamp® XP-E2 Torch LED provides •
Available in cool white
Characteristics................................................ 2
lumen output similar to the XLamp XP-G •
Binned at 25 °C
Flux Characteristics........................................ 2
LED but in the smaller optical source of
Maximum drive current: 1.5 A
Relative Spectral Power Distribution............. 3
the XP-E2 LED. Together with a higher •
Low thermal resistance: 10°C/W
Relative Flux vs. Junction Temperature......... 3
maximum current rating than XP‑E2 and •
Wide viewing angle: 125°
Electrical Characteristics................................ 4
simplified color binning, the XLamp XP‑E2 •
Unlimited floor life at ≤ 30 °C/85% RH
Relative Flux vs. Current................................. 4
Torch LED is fully optimized for a wide •
Reflow solderable - JEDEC J-STD‑020C
Typical Spatial Distribution............................. 5
range of mainstream portable lighting
compatible
Thermal Design............................................... 5
•
Electrically neutral thermal path
Performance Groups - Brightness................. 6
•
RoHS compliant
Performance Groups - Chromaticity.............. 6
applications.
•
ANSI White Bin Plotted on the 1931 CIE
Color Space..................................................... 6
Bin and Order Code Formats.......................... 7
Reflow Soldering Characteristics................... 8
Notes............................................................... 9
Mechanical Dimensions............................... 10
Tape and Reel................................................ 11
Packaging...................................................... 12
Cree LED / 4400 Silicon Drive / Durham, NC 27703 USA / +1.919.313.5330 / www.cree-led.com
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
CLD-DS101
REV 3
1
XLAMP ® XP-E2 TORCH LED
CHARACTERISTICS
Characteristics
Unit
Thermal resistance, junction to solder point
°C/W
10
degrees
125
mV/°C
-1.5
Viewing angle (FWHM)
Temperature coefficient of voltage
ESD withstand voltage (HBM per Mil-Std-883D)
Minimum
Typical
Maximum
V
8000
mA
1500
Reverse voltage
V
1
Forward voltage (@ 1050 mA, 25 °C)
V
LED junction temperature
°C
DC forward current
3.25
3.9
150
FLUX CHARACTERISTICS (TJ = 25 °C)
The following table provides order codes for XLamp XP-E2 Torch LEDs.
Color
CCT Range
Min.
Cool White
6000 K
Max.
10,500 K
Minimum Luminous Flux
(lm) @ 1050 mA
Calculated Minimum
Luminous Flux (lm) *
Order Code
Group
Flux (lm)
1.5 A
T6
280
357
XPEBTT-01-0000-00T80
U2
300
382
XPEBTT-01-0000-00U80
U3
320
407
XPEBTT-01-0000-00V80
U4
340
433
XPEBTT-01-0000-00W80
U5
360
458
XPEBTT-01-0000-00Y80
Notes:
•
•
*
Cree LED maintains a tolerance of ±7% on flux and power measurements, ±0.015 on chromaticity (CCx, CCy) measurements and ±2 on CRI
measurements. See the Measurements section (page 9).
Typical CRI for Cool White (6000 K – 10,500 K CCT) is 65.
Calculated flux values at 1.5 A are for reference only.
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
CLD-DS101
REV 3
2
XLAMP ® XP-E2 TORCH LED
Relative Spectral Power
RELATIVE SPECTRAL POWER DISTRIBUTION
100%
Relative Radiant Power
80%
60%
Cool White
40%
20%
0%
380
430
480
530
580
630
680
730
780
Wavelength (nm)
Relative Flux Output vs. Junction Temperature
RELATIVE FLUX VS. JUNCTION TEMPERATURE (IF = 1050 mA)
120%
Relative Luminous Flux
100%
80%
60%
40%
20%
0%
25
50
75
100
125
150
Junction Temperature (ºC)
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
CLD-DS101
REV 3
3
XLAMP ® XP-E2 TORCH LED
Electrical Characteristics (Tj = 25ºC)
ELECTRICAL CHARACTERISTICS (TJ = 25 °C)
1500
1400
1300
Forward Current (mA)
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
2.70
2.80
2.90
3.00
3.10
3.20
3.30
3.40
3.50
Forward Voltage (V)
Relative Intensity vs. Current (Tj = 25ºC)
RELATIVE FLUX VS. CURRENT (TJ = 25 °C)
140%
Relative Luminous Flux
120%
100%
80%
60%
40%
20%
0%
0
100
200
300
400
500
600
700
800
900 1000 1100 1200 1300 1400 1500
Forward Current (mA)
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
CLD-DS101
REV 3
4
XLAMP ® XP-E2 TORCH LED
Typical Spatial Radiation Pattern
TYPICAL SPATIAL DISTRIBUTION
100%
Relative Luminous Intensity
80%
60%
40%
20%
-90
-70
-50
-30
-10
0%
10
30
50
70
90
Angle (º)
Thermal Design
THERMAL DESIGN
Cool White
The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end
product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life
and optical characteristics.
1600
Maximum Current (mA)
1400
1200
1000
800
600
Rj-a = 12.5°C/W
400
Rj-a = 15°C/W
Rj-a = 20°C/W
200
Rj-a = 25°C/W
0
0
20
40
60
80
100
120
140
160
Ambient Temperature (ºC)
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
CLD-DS101
REV 3
5
XLAMP ® XP-E2 TORCH LED
PERFORMANCE GROUPS - BRIGHTNESS (TJ = 25 °C)
XLamp XP-E2 Torch LEDs are tested for luminous flux and placed into one of the following bins.
Group Code
Minimum Luminous
Flux
Maximum Luminous
Flux
T6
280
300
U2
300
320
U3
320
340
U4
340
360
U5
360
380
PERFORMANCE GROUPS - CHROMATICITY (TJ = 25 °C)
XLamp XP-E2 Torch LEDs are tested for chromaticity and placed into the bin defined by the following bounding coordinates.
Bin
T1
x
y
0.302
0.33
0.318
0.33
0.295
0.28
0.282
0.28
ANSI WHITE BIN PLOTTED ON THE 1931 CIE COLOR SPACE (TJ = 25 °C)
0.40
0.39
4500 K
5000 K
0.38
5700 K
0.37
7000 K
CCy
0.35
WG
WJ
0.34
8300 K
WF
WD
0.33
0.32
WH
6350 K
0.36
WE
10000 K
0.31
WC
WN
WB
0.30
WM
WA
0.29
WP
WK
0.28
0.37
0.36
0.35
0.34
0.33
0.32
0.31
0.30
0.29
0.28
0.27
0.26
0.27
CCx
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
CLD-DS101
REV 3
6
XLAMP ® XP-E2 TORCH LED
BIN AND ORDER CODE FORMATS
Bin codes and order codes are configured as follows.
Order CodeBin Code
Series
XPE = XP-E
Series
XPE = XP-E
Color specification
01 = No CRI minimum
Color specification
01 = No CRI minimum
Kit number
Luminous flux group
SSSCCC-BD-WWW-FF-G-AA
SSSCCC-BD-HHHH-GGNNN
Internal code
Internal code
Color
BTT = Torch
Chromaticity
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
Color
BTT = Torch
CLD-DS101
REV 3
7
XLAMP ® XP-E2 TORCH LED
REFLOW SOLDERING CHARACTERISTICS
In testing, Cree LED has found XLamp XP-E2 Torch LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below.
As a general guideline, Cree LED recommends that users follow the recommended soldering profile provided by the manufacturer of the
solder paste used, and therefore it is the lamp or luminaire manufacturer’s responsibility to determine applicable soldering requirements.
Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
tP
TP
Critical Zone
TL to TP
Temperature
Ramp-up
TL
tS
Tsmax
Tsmin
Ramp-down
ts
Preheat
25
t 25˚C to Peak
IPC/JEDEC J-STD-020C
Time
Profile Feature
Average Ramp-Up Rate (Tsmax to Tp)
Lead-Free Solder
1.2 °C/second
Preheat: Temperature Min (Tsmin)
120 °C
Preheat: Temperature Max (Tsmax)
170 °C
Preheat: Time (tsmin to tsmax)
65-150 seconds
Time Maintained Above: Temperature (TL)
Time Maintained Above: Time (tL)
Peak/Classification Temperature (Tp)
217 °C
45-90 seconds
235 - 245 °C
Time Within 5 °C of Actual Peak Temperature (tp)
20-40 seconds
Ramp-Down Rate
1 - 6 °C/second
Time 25 °C to Peak Temperature
4 minutes max.
Note: All temperatures refer to topside of the package, measured on the package body surface.
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
CLD-DS101
REV 3
8
XLAMP ® XP-E2 TORCH LED
NOTES
Measurements
The luminous flux, radiant power, chromaticity, forward voltage and CRI measurements in this document are binning specifications only
and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number
of factors that are not within Cree LED’s control and are not intended or provided as operational specifications for the products. Calculated
values are provided for informational purposes only and are not intended or provided as specifications.
Pre‑Release Qualification Testing
Please read the LED Reliability Overview for details of the qualification process Cree LED applies to ensure long-term reliability for XLamp
LEDs and details of Cree LED’s pre-release qualification testing for XLamp LEDs.
Moisture Sensitivity
Cree LED recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to
soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity.
Once the MBP is opened, XLamp XP-E2 Torch LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life
in conditions of ≤ 30 ºC/85% relative humidity (RH). Regardless of the storage condition, Cree LED recommends sealing any unsoldered
LEDs in the original MBP.
RoHS Compliance
The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold
limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as
implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree LED representative or from the Product
Ecology section of the Cree LED website.
Vision Advisory
WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please
refer to the LED Eye Safety application note.
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
CLD-DS101
REV 3
9
XLAMP ® XP-E2 TORCH LED
66
55
NOTICE
NOTICE
CREE
CONFIDENTIAL.
THIS
PLOT
AND
THE
INFORMATION
CREE
CONFIDENTIAL.
THIS
PLOT
AND
THE
INFORMATION
CONTAINED
WITHIN
ARE
THE
PROPRIETARY
AND
CONTAINED
WITHIN
ARE
THE
PROPRIETARY
AND
CONFIDENTIAL
INFORMATION
OF
CREE,
INC.
THIS
PLOT
CONFIDENTIAL
INFORMATION
OF
CREE,
INC.
THIS
PLOT
MECHANICAL
DIMENSIONS
MAY
NOT
BE
COPIED,
REPRODUCED
OR
DISCLOSED
TO
ANY
MAY
NOT
BE
COPIED,
REPRODUCED
OR
DISCLOSED
TO
ANY
UNAUTHORIZED
PERSON
THE
WITHOUT
WRITTEN
CONSENT
UNAUTHORIZED
PERSON
THE
WITHOUT
WRITTEN
CONSENT
OF
CREE
INC.
OF
CREE
INC.
44
33
Thermal vias, if present, are not shown on these drawings.
3.30
3.30
.50.50
All measurements are ±.13 mm unless otherwise indicated..
DD
3.45
3.45
2.30
2.30
2.26
2.26
.50.50
.73.73
Anode
6
5
6
5
NOTICE
CREENOTICE
CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OPTICAL
OPTICAL
CREE CONFIDENTIAL.
PLOT
AND
INFORMATION
CONTAINED THIS
WITHIN
ARE
THETHE
PROPRIETARY
AND
REFERENCE
REFERENCE
CONTAINED
WITHIN ARE INFORMATION
THE PROPRIETARY
AND INC. THIS
CONFIDENTIAL
OF CREE,
PLOT
CONFIDENTIAL
INFORMATION
OF
CREE,
INC.
THIS
PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
MAY NOTUNAUTHORIZED
BE COPIED, REPRODUCED
OR DISCLOSED
TO ANY
PERSON THE
WITHOUT
WRITTEN CONSENT
UNAUTHORIZED
PERSON
THE
WITHOUT
WRITTEN CONSENT
OF CREE
INC.
3.45
OF CREE INC.
3.45
4
4
REV
3.30
3.30
D
4
Y
D
4
3
3.45
3.45
REV
OPTICAL
OPTICAL
REFERENCE
REFERENCE
CC
Top View
3.30
2.26
.73
3.45
3.45
2.26
2.30
.50
.73
3.30
.50
2.30
.50
2
2.26
R1.53
R1.53
REV
2
1
2.26
REVISONS
REVISONS
DESCRIPTION
.73
.73DESCRIPTION .58.58
BY
12.30
.50
1.30
1.30
PRIMARY
PRIMARY
3.30 REF.
3.30 REF.
.50
D
3.30
D
R1.53
.50.50
3.30
.50
2.30
.50
.50
BY DATE
APP'D
DATE APP'D
Side View
OPTICAL
OPTICAL
REFERENCE
REFERENCE
R1.53
OPTICAL
OPTICAL
REFERENCE
REFERENCE
C
C
3
3
3
.50.50
.50.50
3.30
.58
.58
.64.64
1.30
3.30 1.30
REF.
3.30 REF.
PRIMARY
PRIMARY
BB
3
.58
.58
Anode
Anode 3.30
3.30
1.30
1.30
Bottom View
.50
PRIMARY
.50
PRIMARY
.50
.50
.50
3.30
3.30
.64
.75.75
.64
.64
ALL
DIME
ALL
DIM
3.30
3.30
.64
RECOMMENDED
PCB
SOLDER
PAD
RECOMMENDED
PCB
SOLDER
PAD
3.30
3.30
RECOMMENDED
STENCIL
PATTERN
RECOMMENDED
STENCIL
PATTERN
(HATCHED
AREA
IS IS
OPENING)
(HATCHED
AREA
OPENING)
.75
66
3.30
3.30
3.30
3.30
.25
.25.25
2.30
2.30
3.30
3.30
B
.50
.50
ALTERNATIVE
ALTERNATIVE
C
1.01
1.01
AA
.50
C
Alternate Bottom View
1.30
1.30
B
3.30
3.30
1.30
.25
1.30 5 5
Recommended PCB Solder Pad
1.01
1.01
2.30
3.30
44
2.30
UNLESS
UNLES
DIME
DIM
MILLIMET
MILLIM
.25
TOLERAN
TOLER
.X
.X
X°
THIRD
ANGLE
PROJECTION
THIRD ANGLE PROJECTION
FOR
SHE
FOR
S
.75
.X
.X
B
.X
B
X°
SURFAC
SURF
.25
33
ALL DIME
ALL DIMENSIONS ARE
3.30
Recommended Stencil Pattern
RECOMMENDED STENCIL PATTERN
(Hatched
Area
is PATTERN
Open)
RECOMMENDED
STENCIL
UNLESS
UNLESS OTHERWISE
DIMEN
DIMENSIONS
ARE
MILLIMET
MILLIMETERSTOLERAN
AND AF
.75
(HATCHED AREA IS OPENING)
(HATCHED AREA IS OPENING)
TOLERANCE UNLESS
.X
RECOMMENDED
PCB
SOLDER
PAD
.XX ± .25 .X
© 2014-2021 Cree LED. The information
in this document
subject to
change
without
notice. Cree® and the Cree logo are registered trademarks, and
CLD-DS101
RECOMMENDED
PCBis SOLDER
PAD
.XXX± .125X°
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
REV
3
THIRD ANGLE PROJECTION
X° ± FOR
.5°SHE
THIRD ANGLE PROJECTION
FOR SHEET METAL.X
P
1.01
ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED
1.01
.X ± 1.5 .X
ALL DIMENSIONS ARE ± .13MM UNLESS OTHERWISE NOTED
2.30
.XX ± .75 .X
2.30
.XXX± .25 X°
A
A
.75
10
±0.
0
5
Y
5
E1
1.7
Do
DETAIL B
SCALE
2:1
XLAMP ® XP-E2 TORCH LED
REF
4.375
REF
Bo
SECTION Y-Y
REF
R0.2
TYPICAL
Y
Ko conform to EIA-481D, Automated
All Cree LED carrier tapes
Component Handling Systems Standard.
P1
D1
1.5
MIN.
SECTION Y-Y
REF 0.59
Y
D1
1.5 MIN.
R
4
2.2
Ao
Do
REF
1.5
5
P2
2.0 ±0.05 (I)
±0.
0
Po
4.0 ±0.1 (II)
CATHODE SIDE
Y
5
Bo
1.75±.10
3.70
Bo
Y 3.70
Ko +.3 D1
2.40
1.5 MIN.
12.0
F
5.50
.0
8.00
P1
W
12.00
(I)
Cathode Side
+/- 0.1
2.2
P1
3.70
+/- 0.1
Bo
Ko
F
3.70
2.40
5.50
8.00
12.00
+/- 0.1
+0.0/-0.1
+/- 0.05
2.5±.1
(II)
ANODE SIDE
+/- 0.1
+0.0/-0.1
+/- 0.05
R
(III)
Ao
REF 0.59
4
SECTION Y-Y
X
X
Ao
P1
W
W
8.0±.1
REF
R0.2
TYPICAL
Ko
Ao
F(III)
SECTION X-X
1.5±.1
4.0±.1
4.375
E1
1.75 ±0.1
T 0.30 ±0.05
All dimensions in mm.
(IV)
+/- 0.1
+0.3/-0.1
Measured from centerline of sprocket hole
to centerline of pocket.
Cumulative tolerance of 10 sprocket
holes is ± 0.20.
Measured from centerline of sprocket
hole to centerline of pocket.
Other material available.
+/- 0.1
+0.3/-0.1
Anode Side
(denoted
by + and circle)
SECTION X-X
User Feed Direction
END
Ao
(I)
3.70
+/- 0.1
(II)
3.70
+/- 0.1
2.40
+0.0/-0.1
5.50
+/- 0.05
6
8.00
P1
+/- 0.1
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
W
12.00
+0.3/-0.1
CONTAINED
WITHIN ARE THE
PROPRIETARY
AND
Bo
Ko
F
(III)
5
Trailer
160mm (min) of
empty pockets
sealed with tape
(20 pockets min.)
6
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTAINED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
Ø190
OF CREE, INC.
3
5
2
ÓÉ Foxit PDF Editor ±à¼°æȨËùÓÐ (c) by Foxit Software Company, 2004
½öÓÃÓÚÆÀ¹À¡£
Loaded Pockets
(1,000 Lamps)
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
OF CREE, INC.
D
(IV)
4
START
Measured from centerline of sprocket hole
to centerline of pocket.
Cumulative tolerance of 10 sprocket
holes is ± 0.20.
Measured from centerline of sprocket
hole to centerline of pocket.
Other material available.
4
Leader
400mm (min) of
empty pockets with
at least 100mm
sealed by tape
(50 empty pockets
min.)
2
3
ÓÉ Foxit PDF Editor ±à¼°æȨËùÓÐ (c) by Foxit Software Company, 2004
½öÓÃÓÚÆÀ¹À¡£
16.40
1
D
1
User Feed Direction
Cover Tape
D
C
D
C
16.40
Ø190
Ø61 ± 0.5
Pocket Tape
OD
7.5
C
12.40 +2.00
0
MEASURED AT HUB
''
C
B
B
13mm
Ø13
Ø61 ± 0.5
7"
OD
7.5
''
12.40
MEASURED AT INSIDE EDGE
12.40 +2.00
0
MEASURED AT HUB
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
®
the Cree LED logo
B is a trademark, of Wolfspeed, Inc. XLamp is a registered trademark of Cree LED.
A
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS & BEFORE FINISH.
TOLERANCE UNLESS SPECIFIED:
.X ± 0.3
.XX ± .13
Ø13
THIRD ANGLE PROJECTION
X°
± 1°
DRAWN BY
LIUDEZHI
2012/5/25
CHECK
DATE
APPROVED
DATE
B
4600 Silicon Drive
Durham, N.C 27703
Phone (919) 361-4770
A
TITLE
MATERIAL
11
CLD-DS101
REV 3
DATE
Reel,
7" x 12mm Wide
RE
TAPE AND REEL
F(III)
Bo
R0.2
TYPICAL
Ko
X
X
4.375
XLAMP ® XP-E2 TORCH LED
PACKAGING
Unpackaged Reel
Vacuum-Sealed
Vacuum-Sealed
Moisture
Barrier Bag
Moisture Barrier Bag
Label
CREE
Binwith
Code Cree Bin
&
Barcode
LabelLot #
Code,
Qty,
Label with Cree Bin Code,
Quantity, Reel ID
Label
with
Cree Bin
Label with
Customer
P/N, Qty,Qty,
Lot #, Lot
PO # #
Code,
Packaged Reel
Patent Label
Label with Customer Order
Label
with Cree Order Code,
Code, Qty, Reel ID, PO #
Quantity, Reel ID, PO #
Label with Cree Bin Code,
Quantity, Reel ID
Boxed Reel
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Bin Code,
Quantity, Reel ID
© 2014-2021 Cree LED. The information in this document is subject to change without notice. Cree® and the Cree logo are registered trademarks, and
the Cree LED logo is a trademark, of Wolfspeed, Inc. XLamp® is a registered trademark of Cree LED.
Patent Label
(on bottom of box)
CLD-DS101
REV 3
12
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Cree LED:
XPEBTT-01-R250-00Y80 XPEBTT-01-0000-00T80 XPEBTT-01-R250-00U80 XPEBTT-01-0000-00V80 XPEBTT-010000-00U80 XPEBTT-01-0000-00W80 XPEBTT-01-0000-00Y80 XPEBTT-01-R250-00V80 XPEBTT-01-R250-00T80
XPEBTT-01-R250-00W80