LED/LCD-TV
Chassis : U59C/U59E
Model : UN19D4003BD
UN26D4003BD
UN32D4003BD
UN22D5003BF
UN40D5003BF
LN32D40*E*D
SERVICE
TFT-LCD TV
Manual
Contents
1. Precautions
2. Product specifications
3. Disassembly and Reassembly
4. Troubleshooting
5. Wiring Diagram
UN32D4003BD
Contents
1. Precautions............................................................................................................... 1-1
1-1. Safety Precautions.......................................................................................................... 1-1
1-2. Servicing Precautions...................................................................................................... 1-2
1-3. Electrostatically Sensitive Devices (ESD) Precautions................................................... 1-2
1-4. Installation Precautions................................................................................................... 1-3
2. Product specifications............................................................................................. 2-1
2-1. Specifications Information............................................................................................... 2-1
2-2. Detail Factory Option..................................................................................................... 2-12
2-3. Accessories................................................................................................................... 2-14
3. Disassembly and Reassembly................................................................................ 3-1
3-1. Disassembly and Reassembly........................................................................................ 3-1
3-2. How to disassembly Function & IR ASSY........................................................................ 3-7
4. Troubleshooting....................................................................................................... 4-1
4-1. Troubleshooting............................................................................................................... 4-1
4-2. Factory Mode Adjustments............................................................................................ 4-22
4-3. White Balance - Calibration........................................................................................... 4-32
4-4. White Ratio (Balance) Adjustment................................................................................. 4-34
4-5. Software Upgrade.......................................................................................................... 4-37
4-6. Rear Cover Dimension.................................................................................................. 4-39
5. Wiring Diagram......................................................................................................... 5-1
5-1. Wiring Diagram................................................................................................................ 5-1
5-2. Position of Connector...................................................................................................... 5-3
5-3. Connector Functions..................................................................................................... 5-13
5-4. Cables........................................................................................................................... 5-13
This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law.
© 2011 Samsung Electronics Co.,Ltd.
All rights reserved.
Printed in Korea
1. Precautions
1. Precautions
1-1. Safety Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1-1. Warnings
1. For continued safety, do not attempt to modify the circuit board.
2. Disconnect the AC power and DC power jack before servicing.
1-1-2. Servicing the LED TV
1. When servicing the LED TV, Disconnect the AC line cord from the AC outlet.
2. It is essential that service technicians have an accurate voltage meter available at all times.
Check the calibration of this meter periodically.
1-1-3. Fire and Shock Hazard
Before returning the LED TV to the user, perform the following safety checks:
1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the
chassis and other metal parts in the LED TV.
2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and
compartment covers or shields, isolation resistorcapacitor networks, mechanical insulators, etc.
3. Leakage Current Hot Check (Figure 1-1):
WARNING : Do not use an isolation transformer during this test.
Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI
C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).
(READING SHOULD)
NOT BE ABOVE 0.5mA
LEAKAGE
CURRENT
TESTER
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
2-WIRE CORD
*ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND
Figure 1-1. Leakage Current Test Circuit
4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit’s AC switch
first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit,
etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts.
The current measured should not exceed 0.5 milliamp.
Reverse the power-plug prongs in the AC outlet and repeat the test.
1-1-4. Product Safety Notices
Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visual
inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage,
wattage, etc. Parts that have special safety characteristics are identified by
on schematics and parts lists. A substitute
replacement that does not have the same safety characteristics as the recommended replacement part might create
shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever
appropriate.
1-1
1. Precautions
1-2. Servicing Precautions
WARNING:
Caution:
Note:
An electrolytic capacitor installed with the wrong polarity might explode.
Before servicing units covered by this service manual, read and follow the Safety Precautions section of
this manual.
If unforeseen circumstances create conflict between the following servicing precautions and any of the
safety precautions, always follow the safety precautions.
1-2-1 General Servicing Precautions
1. Always unplug the unit’s AC power cord from the AC power source and disconnect the DC Power Jack before
attempting to:
(a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect a test
component in parallel with an electrolytic capacitor.
2. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes
used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such
elements to their original position.
3. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that
the area around the serviced part has not been damaged.
4. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels,
input terminals and earphone jacks).
5. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON.
Connect an insulation resistance meter (500 V) to theblades of the AC plug.
The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be
greater than 1 megohm.
6. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead;
always remove the instrument’s ground lead last.
1-3. Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect
transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your
body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. To avoid a shock hazard,
be sure to remove the wrist strap before applying power to the LED TV.
2. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent
accumulation of an electrostatic charge.
3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs.
4. Use only a grounded-tip soldering iron to solder or desolder ESDs.
5. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static” can generate
electrical charges sufficient to damage ESDs.
6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs
are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive
materials.
7. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective
material to the chassis or circuit assembly into which the device will be installed.
Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.
8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together,
or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-2
1. Precautions
1-4. Installation Precautions
1. For safety reasons, more than a people are required for carrying the product.
2. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock.
3. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal
temperature may cause fire.
4. Bend the external antenna cable when connecting it to the product. This is a measure to protect it from being exposed
to moisture. Otherwise, it may cause a fire or electric shock.
5. Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check
the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric
shock.
6. Keep the antenna far away from any high-voltage cables and install it firmly. Contact with the highvoltage cable or the
antenna falling over may cause fire or electric shock.
7. When installing the product, leave enough space (0.4m) between the product and the wall for ventilation purposes.
A rise in temperature within the product may cause fire.
1-3
2. Product specifications
2. Product specifications
2-1. Specifications Information
2-1-1. Model Comparison
Model
Front view
UD4000ND
UD5003
Steam Mold Black
ToC Dark Gray
All
All
Detail view
All
Front Color
All
19"
22"
Dimensions
WxDxH
(inches)
26"
32"
40"
19"
22"
Weight
(lbs)
26"
32"
40"
Without Stnand
17.6
1.6
10.9
With Stand
17.6
4.9
12.3
Without Stnand
20.3
1.6
12.4
With Stand
20.3
4.9
13.8
Without Stnand
37.2
8.6
22.1
With Stand
37.2
1.4
23.8
Without Stnand
24.6
1.8
14.9
With Stand
24.6
6.7
16.5
Without Stnand
29.8
1.9
17.9
With Stand
29.8
7.2
19.6
Without Stnand
6.2
With Stand
6.4
Without Stnand
7.5
With Stand
7.7
Without Stnand
9.0
With Stand
9.7
Without Stnand
13.9
With Stand
15.9
Without Stnand
21.2
With Stand
24.3
Panel Type
All
Anti Glear
Anti Glear
Internal Memory
All
None
None
DDR
All
64 Mbtye
64 Mbtye
Feature
All
Media Play(JPEG)
Media Play(JPEG)
2-1
2. Product specifications
Model
Front view
LD40*
All
All
Detail view
All
Front Color
2-2
All
Dimensions
WxDxH
(inches)
32"
Weight
(lbs)
32"
Steam Mold Black
Without Stnand
30.9
4.1
19.8
With Stand
30.9
7.2
21.4
Without Stnand
16.9
With Stand
19.1
Panel Type
All
Anti Glear
Internal Memory
All
None
DDR
All
64 Mbtye
Feature
All
Media Play(JPEG)
2. Product specifications
2-1-2. Feature & Specifications
Model
UN19D4003BD
Feature
ሪሪ Digital-TV, RF, 2-HDMI, 1-Component, 1-A/V, 1-USB2.0
ሪሪ Brightness : 250 cd/m2
ሪሪ High Contrast Ratio : MEGA
ሪሪ Response Time : 5 ms
Specifications
Item
Description
LCD Panel
19 inch HD 60Hz
Scanning Frequency
Horizontal : 60 kHz ~ 73 kHz (Automatic)
Vertical : 47 Hz ~ 63 Hz (Automatic)
Display Colors
16.7M color
Maximum resolution
Horizontal : 1366 Pixels
Vertical : 768 Pixels
Input Signal
Analog 0.7 Vp-p ± 5% positive at 75Ω, internally terminated
Input Sync Signal
H/V Separate, TTL, P. or N.
Maximum Pixel Clock rate
74.25MHz
Active Display
Horizontal/Vertical
409.8(H) x 230.4(V) mm / 16.7(H) x 9.4(V) inches
AC power voltage & Frequency AC 110 V ~ 120 V, 60 Hz
Power Consumption
Under 35 W (Under 1 W, Stand by)
Dimensions Set
(W x D x H)
447.2 x 124.0 x 312.4 (mm) / 17.6 x 4.9 x 12.3 (inches)_with stand
Weight (Set)
2.9(kg) / 6.39(lbs)_with stand
447.2 x 39.9 x 277.8 (mm) / 17.6 x 1.6 x 10.9 (inches)_without stand
2.8(kg) / 6.17(lbs)_without stand
TV System
Tunning
Frequency Synthesize (Refer to detailed Frequency Table)
System
ATSC & Clear QAM
Sound
NTSC-M
Environmental Considerations
Operating Temperature: 32˚F ~ 122˚F (0˚C ~ 50˚C)
Operating Humidity: 20% ~ 90%
Storage Temperature: -4˚F ~ 140˚F (-20˚C ~ 60˚C)
Storage Humidity: 10% ~ 90%
Audio Spec.
- MAX Internal Audio Output Power : Each 3W(Left/Right)
- Equalizer : 5band
- Output Frequency : RF : 20 Hz ~ 15.4 kHz
AV/Componet/HDMI : 20 Hz ~ 20 kHz
Note: SRS Trusurround HD, Film mode, Energy Saving
2-3
2. Product specifications
Model
UN26D4003BD
Feature
ሪሪ Digital-TV, RF, 2-HDMI, 1-Component, 1-A/V, 1-USB2.0
ሪሪ Brightness : 250 cd/m2
ሪሪ High Contrast Ratio : MEGA
ሪሪ Response Time : 5 ms
Specifications
Item
Description
LCD Panel
26 inch HD 60Hz
Scanning Frequency
Horizontal : 60 kHz ~ 73 kHz (Automatic)
Vertical : 47 Hz ~ 63 Hz (Automatic)
Display Colors
16.7M color
Maximum resolution
Horizontal : 1366 Pixels
Vertical : 768 Pixels
Input Signal
Analog 0.7 Vp-p ± 5% positive at 75Ω, internally terminated
Input Sync Signal
H/V Separate, TTL, P. or N.
Maximum Pixel Clock rate
74.25MHz
Active Display
Horizontal/Vertical
575.7(H) x 323.7(V) mm / 23.5(H) x 13.2(V) inches
AC power voltage & Frequency AC 110 V ~ 120 V, 60 Hz
Power Consumption
Under 50 W (Under 1 W, Stand by)
Dimensions Set
(W x D x H)
624.0 x 169.4 x 418.3 (mm) / 24.6 x 6.7 x 16.5 (inches)_with stand
Weight (Set)
4.1(kg) / 9.04(lbs)_with stand
624.0 x 45.1 x 377.2 (mm) / 24.6 x 1.8 x 14.9 (inches)_without stand
4.4(kg) / 9.7(lbs)_without stand
TV System
Tunning
Frequency Synthesize (Refer to detailed Frequency Table)
System
ATSC & Clear QAM
Sound
NTSC-M
Environmental Considerations
Operating Temperature: 32˚F ~ 122˚F (0˚C ~ 50˚C)
Operating Humidity: 20% ~ 90%
Storage Temperature: -4˚F ~ 140˚F (-20˚C ~ 60˚C)
Storage Humidity: 10% ~ 90%
Audio Spec.
- MAX Internal Audio Output Power : Each 3W(Left/Right)
- Equalizer : 5band
- Output Frequency : RF : 20 Hz ~ 15.4 kHz
AV/Componet/HDMI : 20 Hz ~ 20 kHz
Note: SRS Trusurround HD, Film mode, Energy Saving
2-4
2. Product specifications
Model
UN32D4003BD
Feature
ሪሪ Digital-TV, RF, 2-HDMI, 1-Component, 1-A/V, 1-USB2.0
ሪሪ Brightness : 250 cd/m2
ሪሪ High Contrast Ratio : MEGA
ሪሪ Response Time : 5 ms
Specifications
Item
Description
LCD Panel
32 inch HD 60Hz
Scanning Frequency
Horizontal : 60 kHz ~ 73 kHz (Automatic)
Vertical : 47 Hz ~ 63 Hz (Automatic)
Display Colors
16.7M color
Maximum resolution
Horizontal : 1366 Pixels
Vertical : 768 Pixels
Input Signal
Analog 0.7 Vp-p ± 5% positive at 75Ω, internally terminated
Input Sync Signal
H/V Separate, TTL, P. or N.
Maximum Pixel Clock rate
74.25MHz
Active Display
Horizontal/Vertical
700.4(H) x 394.8(V) mm / 28.6(H) x 16.1(V) inches
AC power voltage & Frequency AC 110 V ~ 120 V, 60 Hz
Power Consumption
Under 70 W (Under 1 W, Stand by)
Dimensions Set
(W x D x H)
756.4 x 182.4 x 498.1 (mm) / 29.8 x 7.2 x 19.6 (inches)_with stand
Weight (Set)
6.30(kg) / 13.89(lbs)_with stand
756.4 x 47.8 x 454.0 (mm) / 29.8 x 7.2 x 19.6 (inches)_without stand
7.20(kg) /15.87(lbs)_without stand
TV System
Tunning
Frequency Synthesize (Refer to detailed Frequency Table)
System
ATSC & Clear QAM
Sound
NTSC-M
Environmental Considerations
Operating Temperature: 32˚F ~ 122˚F (0˚C ~ 50˚C)
Operating Humidity: 20% ~ 90%
Storage Temperature: -4˚F ~ 140˚F (-20˚C ~ 60˚C)
Storage Humidity: 10% ~ 90%
Audio Spec.
- MAX Internal Audio Output Power : Each 3W(Left/Right)
- Equalizer : 5band
- Output Frequency : RF : 20 Hz ~ 15.4 kHz
AV/Componet/HDMI : 20 Hz ~ 20 kHz
Note: SRS Trusurround HD, Film mode, Energy Saving
2-5
2. Product specifications
Model
UN22D5003BF
Feature
ሪሪ Digital-TV, RF, 2-HDMI, 1-Component, 1-A/V, 1-USB2.0
ሪሪ Brightness : 250 cd/m2
ሪሪ High Contrast Ratio : MEGA
ሪሪ Response Time : 5 ms
Specifications
Item
Description
LCD Panel
22 inch FHD 60Hz
Scanning Frequency
Horizontal : 60 kHz ~ 73 kHz (Automatic)
Vertical : 47 Hz ~ 63 Hz (Automatic)
Display Colors
16.7M color
Maximum resolution
Horizontal : 1366 Pixels
Vertical : 768 Pixels
Input Signal
Analog 0.7 Vp-p ± 5% positive at 75Ω, internally terminated
Input Sync Signal
H/V Separate, TTL, P. or N.
Maximum Pixel Clock rate
74.25MHz
Active Display
Horizontal/Vertical
476.6(H) x 268.1(V) mm / 19.5(H) x 10.9(V) inches
AC power voltage & Frequency AC 110 V ~ 120 V, 60 Hz
Power Consumption
Under 45 W (Under 1 W, Stand by)
Dimensions Set
(W x D x H)
515.8 x 124.0 x 350.0 (mm) / 20.3 x 4.9 x 13.8 (inches)_with stand
Weight (Set)
3.50(kg) / 7.72(lbs)_with stand
515.8 x 39.9 x 315.6 (mm) / 20.3 x 1.6 x 12.4 (inches)_without stand
3.40(kg) / 7.50(lbs)_without stand
TV System
Tunning
Frequency Synthesize (Refer to detailed Frequency Table)
System
ATSC & Clear QAM
Sound
NTSC-M
Environmental Considerations
Operating Temperature: 32˚F ~ 122˚F (0˚C ~ 50˚C)
Operating Humidity: 20% ~ 90%
Storage Temperature: -4˚F ~ 140˚F (-20˚C ~ 60˚C)
Storage Humidity: 10% ~ 90%
Audio Spec.
- MAX Internal Audio Output Power : Each 3W(Left/Right)
- Equalizer : 5band
- Output Frequency : RF : 20 Hz ~ 15.4 kHz
AV/Componet/HDMI : 20 Hz ~ 20 kHz
Note: SRS Trusurround HD, Film mode, Energy Saving
2-6
2. Product specifications
Model
UN40D5003BF
Feature
ሪሪ Digital-TV, RF, 2-HDMI, 1-Component, 1-A/V, 1-USB2.0
ሪሪ Brightness : 250 cd/m2
ሪሪ High Contrast Ratio : MEGA
ሪሪ Response Time : 5 ms
Specifications
Item
Description
LCD Panel
40 inch FHD 60Hz
Scanning Frequency
Horizontal : 60 kHz ~ 73 kHz (Automatic)
Vertical : 47 Hz ~ 63 Hz (Automatic)
Display Colors
16.7M color
Maximum resolution
Horizontal : 1366 Pixels
Vertical : 768 Pixels
Input Signal
Analog 0.7 Vp-p ± 5% positive at 75Ω, internally terminated
Input Sync Signal
H/V Separate, TTL, P. or N.
Maximum Pixel Clock rate
74.25MHz
Active Display
Horizontal/Vertical
888.2(H) x 501.3(V) mm / 36.3(H) x 20.5(V) inches
AC power voltage & Frequency AC 110 V ~ 120 V, 60 Hz
Power Consumption
Under 100 W (Under 1 W, Stand by)
Dimensions Set
(W x D x H)
943.8 x 219.4 x 603.5 (mm) / 37.2 x 8.6 x 23.8 (inches)_with stand
Weight (Set)
9.60(kg) / 21.16(lbs)_with stand
943.8 x 51.0 x 561.4 (mm) / 37.2 x 2.0 x 22.1 (inches)_without stand
11.00(kg) / 24.25(lbs)_without stand
TV System
Tunning
Frequency Synthesize (Refer to detailed Frequency Table)
System
ATSC & Clear QAM
Sound
NTSC-M
Environmental Considerations
Operating Temperature: 32˚F ~ 122˚F (0˚C ~ 50˚C)
Operating Humidity: 20% ~ 90%
Storage Temperature: -4˚F ~ 140˚F (-20˚C ~ 60˚C)
Storage Humidity: 10% ~ 90%
Audio Spec.
- MAX Internal Audio Output Power : Each 3W(Left/Right)
- Equalizer : 5band
- Output Frequency : RF : 20 Hz ~ 15.4 kHz
AV/Componet/HDMI : 20 Hz ~ 20 kHz
Note: SRS Trusurround HD, Film mode, Energy Saving
2-7
2. Product specifications
Model
LN32D40*E*D
Feature
ሪሪ Digital-TV, RF, 2-HDMI, 1-Component, 1-A/V, 1-USB2.0
ሪሪ Brightness : 250 cd/m2
ሪሪ High Contrast Ratio : MEGA
ሪሪ Response Time : 5 ms
Specifications
Item
Description
LCD Panel
32 inch HD 60Hz
Scanning Frequency
Horizontal : 60 kHz ~ 73 kHz (Automatic)
Vertical : 47 Hz ~ 63 Hz (Automatic)
Display Colors
16.7M color
Maximum resolution
Horizontal : 1366 Pixels
Vertical : 768 Pixels
Input Signal
Analog 0.7 Vp-p ± 5% positive at 75Ω, internally terminated
Input Sync Signal
H/V Separate, TTL, P. or N.
Maximum Pixel Clock rate
74.25MHz
Active Display
Horizontal/Vertical
669.4(H) x 394.3(V) mm / 27.3(H) x 16.1(V) inches
AC power voltage & Frequency AC 110 V ~ 120 V, 60 Hz
Power Consumption
Under 110 W (Under 1 W, Stand by)
Dimensions Set
(W x D x H)
784.4 x 181.9 x 542.3 (mm) / 30.9 x 7.2 x 21.4 (inches)_with stand
Weight (Set)
8.66(kg) / 19.09(lbs)_with stand
784.4 x 103.3 x 502.9 (mm) / 30.9 x 4.1 x 19.8 (inches)_without stand
7.65(kg) / 16.87(lbs)_without stand
TV System
Tunning
Frequency Synthesize (Refer to detailed Frequency Table)
System
ATSC & Clear QAM
Sound
NTSC-M
Environmental Considerations
Operating Temperature: 32˚F ~ 122˚F (0˚C ~ 50˚C)
Operating Humidity: 20% ~ 90%
Storage Temperature: -4˚F ~ 140˚F (-20˚C ~ 60˚C)
Storage Humidity: 10% ~ 90%
Audio Spec.
- MAX Internal Audio Output Power : Each 3W(Left/Right)
- Equalizer : 5band
- Output Frequency : RF : 20 Hz ~ 15.4 kHz
AV/Componet/HDMI : 20 Hz ~ 20 kHz
Note: SRS Trusurround HD, Film mode, Energy Saving
2-8
2. Product specifications
2-1-3. Specification Comparison to Old Models
※※O : application, X : non-application
Model
UD4N(UN**D4003BD)
UD4N(UN32D4000ND)
Display Type
LED TV
LED TV
Built-in Tuner
O
O
Resolution
1366 X 768
1366 X 768
LCD Panel
TFT LCD Panel 60Hz
TFT LCD Panel 60Hz
Screen Size
19" / 26" / 32"
19" / 32"
Picture ratio
16 : 9
16 : 9
Design
19"
Dimensions (WxHxD)
26"
32"
19"
Weight
26"
32"
Brightness
Contrast Ratio
Picture Enhacer
17.6 x 4.9 x 12.3(inches) with stand
17.6 x 1.6 x 10.9(inches) without stand
18.8 x 7.5 x 14.7(inches) with stand
19"
24.6 x 6.7 x 16.5(inches) with stand
24.6 x 1.8 x 14.9(inches) without stand
29.8 x 7.2 x 19.6(inches)with stand
32"
29.8 x 1.9 x 17.9(inches) without stand
6.39(lbs) with stand
6.17(lbs) without stand
9.70 (lbs) without stand
32"
15.87 (lbs) without stand
19"
250 cd/m2
26"
250 cd/m2
32"
30.1 x 8.8 x 20.8(inches) with stand
30.1 x 8.8 x 18.2(inches) without stand
8.60(lbs) with stand
19"
9.04 (lbs) with stand
13.89 (lbs) with stand
18.8 x 1.2 x 12.6(inches) without stand
7.90(lbs) without stand
19.80(lbs) with stand
15.40(lbs) without stand
19"
450 cd/m2
250 cd/m2
32"
450 cd/m2
19"
Mega
19"
Mega
26"
Mega
32"
Mega
32"
Mega
DNIe (Saturn4)
HyperReal Engine (X5)
5 Band
5 Band
O
O
Surround Sound
SRS TruSurround HD
Dolby Digital Plus/Pulse
Speaker Output
5Wx5W
3 W(19"), 5 W(32")
PIP
X
O
Caption
O
O
Entertainment Mode
X
X
Game Mode
X
O
Energy Saving
O
O
Network
X
X
Anynet
X
O
1(Cable/Air)
1(Cable/Air)
Equalizer
Auto Volume Control
+
Antenna
2-9
2. Product specifications
※※ O : application, X : non-application
Model
UD5P(UN**D5003BF)
UD5P(UN22/27D5000NF) / UD5R(UN32/40D5500RF)
Display Type
LED TV
LED TV
Built-in Tuner
O
O
Design
Resolution
1366 X 768
1366 X 768
LCD Panel
TFT LCD Panel 60Hz
TFT LCD Panel 60Hz
Screen Size
22" / 40"
22" / 27" / 32" / 40"
Picture ratio
16 : 9
16 : 9
20.3 x 4.9 x 13.8(inches) with stand
22"
20.3 x 1.6 x 12.4(inches) without stand
27"
37.2 x 8.6 x 23.8(inches) with stand
32"
37.2 x 2.0 x 22.1(inches) without stand
40"
7.72(lbs) with stand
22"
7.50(lbs) without stand
27"
21.26(lbs) with stand
32"
24.25(lbs) without stand
40"
22"
Dimensions (WxHxD)
40"
22"
Weight
40"
22"
250 cd/m2
40"
250 cd/m2
22"
Mega
40"
Mega
Brightness
Contrast Ratio
Picture Enhacer
Equalizer
Auto Volume Control
21.5 x 7.5 x 16.2(inches) with stand
21.5 x 1.2 x 14.1(inches) without stand
25.7 x 8.7 x 18.9(inches) with stand
25.7 x 1.2 x 16.6(inches) without stand
30.2 x 1.2 x 18.4(inches) with stand
30.2 x 9.4 x 20.9(inches) without stand
37.6 x 10.0 x 25.1(inches) with stand
37.6 x 1.2 x 22.6(inches) without stand
9.00(lbs) with stand
8.20(lbs) without stand
13.70(lbs) with stand
12.10(lbs) without stand
9.96(lbs) with stand
7.22(lbs) without stand
14.36(lbs) with stand
11.08(lbs) without stand
22"
450 cd/m2
27"
450 cd/m2
32"
450 cd/m2
40"
450 cd/m2
22"
Mega
27"
Mega
32"
Mega
40"
Mega
DNIe (Saturn4)
HyperReal Engine (X5)
5 Band
5 Band
O
O
Surround Sound
SRS TruSurround HD
Dolby Digital Plus/Pulse
Speaker Output
22" : 5 W / 40" : 10W
22" : 3 W / 22" : 5 W / 32" / 40" : 10W
PIP
X
O
Caption
O
O
Entertainment Mode
X
X
Game Mode
X
O
Energy Saving
O
O
Network
X
X
Anynet
+
Antenna
2-10
X
O
1(Cable/Air)
1(Cable/Air)
2. Product specifications
※※O : application, X : non-application
Model
LD4E(LN**D40*E*D)
LD4G(LN**D450G1D)
Display Type
LCD TV
LCD TV
Built-in Tuner
O
O
Resolution
1366 X 768
1366 X 768
LCD Panel
TFT LCD Panel 60Hz
TFT LCD Panel 60Hz
Screen Size
32"
26" / 32"
Picture ratio
16 : 9
16 : 9
Design
Dimensions (WxHxD)
Weight
30.9 x 7.2 x 21.4(inches)with stand
26"
30.9 x 4.1 x 19.8(inches) without stand
32"
6.39(lbs) with stand
26"
6.17(lbs) without stand
32"
32"
32"
Brightness
32"
250 cd/m2
Contrast Ratio
32"
Mega
Picture Enhacer
26.0 x 8.7 x 19.0(inches) with stand
26.0 x 3.1 x 17.1(inches) without stand
31.3 x 9.9 x 22.5(inches) with stand
31.3 x 3.2 x 20.1(inches) without stand
14.80(lbs) with stand
13.80(lbs) without stand
23.90(lbs) with stand
19.00(lbs) without stand
26"
400 cd/m2
32"
400 cd/m2
19"
TBD
32"
Mega
DNIe (Saturn4)
HyperReal Engine (X5)
5 Band
5 Band
O
O
Surround Sound
SRS TruSurround HD
Dolby Digital Plus/Pulse
Speaker Output
5W
5 W(26"), 10 W(32")
PIP
X
O
Caption
O
O
Entertainment Mode
X
X
Game Mode
X
O
Energy Saving
O
O
Network
X
X
Equalizer
Auto Volume Control
Anynet
+
Antenna
X
O
1(Cable/Air)
1(Cable/Air)
2-11
2. Product specifications
2-2. Detail Factory Option
※※If you replace the main board with new one, please change the factory option as well.
The options you must change are “Type”.
2-2-1. UD4003
Model Name
UN19D4003BD
UN26D4003BD
UN32D4003BD
Vendor
AMLCD
CMI
AMLCD
CODE
BN07-01043A
BN07-01049A
BN95-00437A
SPEC
LTM185AT05-V
LD260AGC-C1
S260L1-H62
LTJ320AP02
Vendor
Powernet
SEM
DONGYANG
CODE
BN44-00467A
BN44-00471A
BN44-00472B
SPEC
PD22A0_BPNV
PD26G0S_BSM
PD32G0S_BSY
Panel
SMPS
1
Factory Reset
-
-
-
2
Type
-
-
-
3
Model
D4003
D4003
D4003
4
Tuner
ALPS
ALPS
ALPS
5
Audio Amp
NTP7411S
NTP7411S
NTP7411S
6
Front Color
NONE
NONE
NONE
7
Local Set
Other
Other
Other
8
Exhibition Mode
Off
Off
Off
2-2-2. UD5003
Model Name
Panel
SMPS
UN22D5003BF
UN40D5003BF
Vendor
AMLCD
AMLCD
CODE
BN07-01044A
BN95-00434A
SPEC
LTM215HT04
LTJ400HM05
Vendor
Powernet
SEM
CODE
BN44-00467A
BN44-00473A
SPEC
PD22A0_BPNV
PD46G0_BSM
1
Factory Reset
-
-
2
Type
-
-
3
Model
D5003
D5003
4
Tuner
ALPS
ALPS
5
Audio Amp
NTP7411S
NTP7411S
6
Front Color
NONE
NONE
7
Local Set
Other
Other
8
Exhibition Mode
Off
Off
2-12
2. Product specifications
2-2-3. LD40*
Model Name
Panel
SMPS
LN32D40*E*D
Vendor
Sharp
CODE
BN07-01050A
SPEC
CD320AGD
Vendor
SEM
CODE
BN44-00468A
SPEC
PSIV121411C
1
Factory Reset
-
2
Type
-
3
Model
D40*
4
Tuner
ALPS
5
Audio Amp
NTP7411S
6
Front Color
NONE
7
Local Set
Other
8
Exhibition Mode
Off
2-13
2. Product specifications
2-3. Accessories
Product
Description
Code. No
Remote Control /
Batteries (AAA x 2)
BN59-01006A
Remark
19D4003 : 3903-000599
26D4003 : 3903-000599
32D4003 : 3903-000599
Power Cord
22D5003 : 3903-000599
40D5003 : 3903-000598
32D40* : 3903-000599
2-14
Warranty Card /
Safety Guide Manual
BN68-03703A
Cleaning Cloth
BN63-01798B
Samsung Electronics
Service center
3. Disassembly and Reassembly
3. Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the LED/LCD TV.
WARNING: This LED/LCD TV contains electrostatically sensitive devices. Use caution when handling these
components.
3-1. Disassembly and Reassembly
Cautions:1. Disconnect the LED TV from the power source before disassembly.
2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.
Description
1
Place TV face down on cushioned table.
2
Remove screws from the Stand.
Picture Description
1
119D4003 : 2 EA
26D4003 : 2 EA
22D5003 : 2 EA
232D4003 : 4 EA
40D5003 : 4 EA
Screws
6003-001782
2
6001-002621
3 32D40* : 4 EA
3
6002-001294
3-1
3. Disassembly and Reassembly
Description
3
Remove stand.
Picture Description
Screws
1
119D4003
26D4003
22D5003
232D4003
40D5003
3 32D40*
4
Remove the screws of rear-cover.
2
3
1
119D4003 : 4 EA
6003-001782
222D5003 : 4 EA
2
6003-001782
326D4003 : 4 EA
3
6003-001782
3-2
3. Disassembly and Reassembly
Description
Picture Description
Screws
432D4003 : 4EA
4
6003-001782
6001-002671
540D5003 : 12 EA
5
6003-001782
6001-002671
632D40* : 8 EA
6
6002-001294
5
Lift up the rear-cover.
6
Remove the left and right speaker.
3-3
3. Disassembly and Reassembly
Description
7
Remove the screws of main board and IP
board.
Picture Description
Screws
1
119D4003 : 7 EA
6003-000115
222D5003 : 7 EA
326D4003 : 9 EA
2
3
6001-002653
432D4003 : 9 EA
540D5003 : 10 EA
632D40* : 9 EA
4
5
6
6001-002284
3-4
3. Disassembly and Reassembly
Description
8
Picture Description
Screws
Remove the 2 screws of stand link cover
and Remove the stand link.
40D5003
6003-001782
9
Remove the screws of stand link.
32D4003
40D5003
6001-002653
40D5003
6001-002653
6003-001782
10
Lift up the stand link.
19D4003
22D5003
26D4003
32D4003
40D5003
3-5
3. Disassembly and Reassembly
Description
Picture Description
32D4003
40D5003
11
Lift up the panel.
※※Reassembly procedures are in the reverse order of disassembly procedures.
Screw Size
Code No.
A (mm)
B (mm)
C (mm)
Q'ty
6003-001782
7.80~8.30
11.20~12.00
3.81~3.91
19D4003 : 6 EA
26D4003 : 6 EA
22D5003 : 6 EA
32D4003 : 11 EA
40D5003 : 13 EA
32D40* : 7 EA
6001-002621
7.80~8.20
7.40~8.00
3.83~3.98
32D4003 : 4 EA
40D5003 : 4 EA
6002-001294
7.80~8.30
15.2~16.0
3.85~4.00
32D40* : 8EA
40D503 :
6001-002671
7.10~7.50
5.70~6.00
2.98~3.02
32D4003 : 1 EA
40D5003 : 3 EA
6003-000115
5.80~6.30
5.20~6.00
2.85~2.95
19D5003 : 7 EA
22D5003 : 7 EA
6001-002653
7.10~7.50
5.70~6.00
2.98~3.02
26D4003 : 9 EA
32D4003 : 13 EA
40D5003 :15 EA
6001-002284
7.80~8.30
7.40~8.60
3.83~3.98
32D40* : 11 EA
3-6
Screws
3. Disassembly and Reassembly
3-2. How to disassembly Function & IR ASSY
Description
1
Check the 2 Function Clips.
(for 32D40*)
2
Remove the front cover.
3
Heat the Function Assy by Heat Gun
and Lift up the Function Assy.
Picture Description
Screws
3-7
4. Troubleshooting
4. Troubleshooting
4-1. Troubleshooting
4-1-1. Previous check
1. Check the various cable connections first.
• Check to see if there is a burnt or damaged cable.
• Check to see if there is a disconnected or loose cable connection.
• Check to see if the cables are connected according to the connection diagram.
2. Check the power input to the Main Board.
14p cable
Power Assy
Power Assy
LVDS Cable
14p cable
Main Assy
Main Assy
Speaker
Speaker
Main Assy (CN202 / 204)
Power Assy (CMN801)
LVDS Cable
T-CON
Speaker
Main Assy (CN201 / 203)
Speaker
Power Assy (CMN801)
1
B5V
2
SW_PW
1
B5V
2
SW_PW
1
B5V
2
SW_PW
1
B5V
2
3
B5V
4
A5V
3
B5V
4
A5V
3
B5V
4
A5V
3
B5V
4
SW_PW
A5V
5
GND
6
GND
5
GND
6
GND
5
GND
6
GND
5
GND
6
GND
7
B12VS
8
GND
7
B12VS
8
GND
7
B12VS
8
GND
7
B12VS
8
GND
SW_INV
9
B12VS
10
SW_INV
9
B12VS
10
SW_INV
9
B12VS
10
SW_INV
9
B12VS
10
11
B13V
12
NC
11
B13V
12
NC
11
B13V
12
NC
11
B13V
12
NC
13
B13V
14
DMM
13
B13V
14
DMM
13
B13V
14
DMM
13
B13V
14
DMM
4-1
4. Troubleshooting
4-1-2. How to check fault symptom
„„ No Power
-- The LEDs on the front panel do not work when connecting the power cord.
Symptom
-- The SMPS relay does not work when connecting the power cord.
-- The units appears to be dead.
Major
checkpoints
The IP relay or the LEDs on the front panel does not work when connecting the power cord if the
cables are improperly connected or the Main Board or SMPS is not functioning.
In this case, check the following:
-- Check the internal cable connection status inside the unit.
-- Check the fuses of each part.
-- Check the output voltage of SMPS.
-- Replace the Main Board.
Power indicator LED on?
No
Check an AC power connection.
Yes
Check the 14P power cable
No
Change 14p power cable or SMPS.
Yes
Check ‘Stand-By 5V’ DC5V appear at
BD207(middle)/BD214(small)?
No
Yes
Check ‘Power input of Main Assy’ ?
DC B13V, B5V appear at BD209(M)/BD221(S)
(B13V), BD208, BD213(M)/BD210, 212(S)(B5V)?
Change SMPS.
No
Yes
Diagnostics
Check ‘Power of main IC(B1.1V)’
Check ‘Power of DDR IC(B1.9V)’
appear at L201 (B1.1V)
BD1012 (B1.9V) ?
No
Change the Main Assy.
Yes
Check ‘Power of LVDS (13V)’ appear at
LVDS connector Pin #1~5 of T-con b’d?
No
Change the LVDS cable.
Yes
Does proper DC B13V appear at F1 of
T-con b’d?
No
Yes
Please, Contact tech support.
Caution
4-2
Make sure to disconnect the power before working on the IP board.
Change the T-con b’d.
4. Troubleshooting
Location (Main) - TOP
Location (Main) - T-CON
4-3
4. Troubleshooting
„„ No video_HDMI1, 2 - Digital signal
Symptom
Major
checkpoints
-- Audio is normal but no picture is displayed on the screen.
-- Check the HDMI source.
-- Check the HDMI switch, Check the Chelsea.
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.
Power indicator LED is off.
Lamp(Backlight) on, no video ?
No
Check a set in the 'Stand-by mode'.
Yes
check the Self Diagnosis
(SupportSelf DiagnosisPicture Test)
Dose the promblem still exist self diagnosis ?
No
Check external devices and
connections.
Yes
Check the HDMI source and
check the connection of HDMI cable ?
No
Input the HDMI signal properly.
Yes

Does the signal appear at
CN602 (Pin#12 , #7 )(HDMI1)
CN601 (Pin#12 , #7 )(HDMI2)
(HDMI RX_Clk , RX_Data) ?
No
Check CN502, CN503.
Check HDMI cable.
Change the Main Assy.
No
Check IC1001 (X5N)
Change the Main Assy.
Yes

Diagnostics
Does the digital data appear at
TP-E_TXCLK+, E_TXCLK- ,
O_TXCLK+, O_TXCLK-?
Yes
Check the LVDS cable ?
Check the T-Con B’d ?
Replace the LCD panel ?
Caution
4-4
No
Please, Contact Tech support.
Make sure to disconnect the power before working on the IP board.
4. Troubleshooting
Location (Main) - TOP
4-5
4. Troubleshooting
„„ WAVEFORMS
4-6

HDMI input (RX_Data, RX_Clk)

LVDS output
4. Troubleshooting
„„ No Video_Tuner - CVBS
Symptom
Major
checkpoints
-- Audio is normal but no picture is displayed on the screen.
-- Check the Tuner CVBS source.
-- Check the Tuner, Check the Chelsea.
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.
Power indicator LED is off.
Lamp(Backlight) on, no video ?
No
Check a set in the 'Stand-by mode'
Yes
Check the RF source and
check the connection of RF cable ?
No
Input the RF source properly.
Yes
check the Self Diagnosis
(SupportSelf DiagnosisPicture Test)
Dose the promblem still exist self diagnosis ?
No
Check external devices and
connections.
Yes
Does the DC B1.8V B3.3V
appear at #3, #5 Pin of Tuner ?
No
Change the Main Assy.
No
Change the Main Assy.
Yes
Check the CVBS data
at #15 Pin of Tuner ?
Yes
Diagnostics

Does the digital data appear at
TP-E_TXCLK+, E_TXCLK- ,
O_TXCLK+, O_TXCLK- ?
No
Check IC1001 (X5N).
Change the Main Assy.
Yes
Check the LVDS cable ?
Check the T-Con B’d ?
Replace the LCD panel ?
Caution
No
Please, Contact Tech support.
Make sure to disconnect the power before working on the IP board.
4-7
4. Troubleshooting
Location (Main) - TOP
4-8
4. Troubleshooting
„„ WAVEFORMS

LVDS output
4-9
4. Troubleshooting
„„ No Video_Tuner DTV
Symptom
Major
checkpoints
-- Audio is normal but no picture is displayed on the screen.
-- Check the DTV source.
-- Check the Tuner, Check the Chelsea.
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.
Power indicator LED is off.
Lamp(Backlight) on, no video ?
No
Check a set in the 'Stand-by mode'
Yes
Check the connection of RF cable ?
No
Input the RF source properly.
Yes
check the Self Diagnosis
(SupportSelf DiagnosisPicture Test)
Dose the promblem still exist self diagnosis ?
No
Check external devices and
connections.
Yes
Check the 'signal strength' in Self Diagnosis
menu Strength is enough ?
No
Check the D-TV source.
Yes
Does the DC B1.8V B3.3V
appear at #3, #5 Pin of Tuner ?
No
Change the Main Assy.
No
Change the Main Assy.
No
Check IC1001 (X5)
Change the Main Assy.
No
Please, Contact Tech support.
Yes
Check the DTV data(DIF+, DIF-)
appear at #11, #10 Pin of Tuner ?
Diagnostics
Yes

Does the digital data appear at
TP-E_TXCLK+, E_TXCLK- ,
O_TXCLK+, O_TXCLK- ?
Yes
Check the LVDS cable ?
Check the T-Con B'd ?
Replace the LCD panel ?
Caution
4-10
Make sure to disconnect the power before working on the IP board.
4. Troubleshooting
Location (Main) - TOP
4-11
4. Troubleshooting
„„ WAVEFORMS

4-12
LVDS output
4. Troubleshooting
„„ No Video_Video CVBS
Symptom
Major
checkpoints
-- Audio is normal but no picture is displayed on the screen.
-- Check the Video CVBS source
-- Check the Chelsea.
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.
Power indicator LED is off.
Lamp(Backlight) on, no video ?
No
Check a set in the 'Stand-by mode'
Yes
Check the video source and
check the connection of video cable?
No
Input the video source properly.
Yes
check the Self Diagnosis
(SupportSelf DiagnosisPicture Test)
Dose the promblem still exist self diagnosis ?
No
Check external devices and
connections.
Yes

Does the CVBS data appear at
R809/R814(CVBS1) ?
No
Check CN503
Change the Main Assy.
No
Check IC1001 (X5)
Change the Main Assy.
No
Please, Contact Tech support.
Yes

Does the digital data appear at
TP-E_TXCLK+, E_TXCLK- ,
O_TXCLK+, O_TXCLK- ?
Yes
Diagnostics
Caution
Check the LVDS cable ?
Check the T-Con B'd ?
Replace the LCD panel ?
Make sure to disconnect the power before working on the IP board.
4-13
4. Troubleshooting
Location (Main) - TOP
4-14
4. Troubleshooting
„„ WAVEFORMS

CVBS OUT (Grey Bar)

LVDS output
4-15
4. Troubleshooting
„„ No Video_Component
Symptom
Major
checkpoints
-- Audio is normal but no picture is displayed on the screen.
-- Check the Component source
-- Check the chelsea.
-- This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected.
Power indicator LED is off.
Lamp(Backlight) on, no video ?
No
Check a set in the 'Stand-by mode'.
Yes
Check the component source and check the
connection of component cables (Y,Pb,Pr) ?
No
Input the component source properly.
Yes
check the Self Diagnosis
(SupportSelf DiagnosisPicture Test)
Dose the promblem still exist self diagnosis ?
No
Check external devices and
connections.
Yes

Does the data appear at
R816/R821(COMP_Y)
R817 (COMP_PB)
R815(COMP_PR)
No
Check CN403.
Change the Main Assy.
No
Check IC1001 (X5N).
Change the Main Assy.
No
Please, Contact Tech support.
Yes

Diagnostics
Does the digital data appear at
TP-E_TXCLK+, E_TXCLK- ,
O_TXCLK+, O_TXCLK- ?
Yes
Check the LVDS cable ?
Check the T-Con B'd ?
Replace the LCD panel ?
Caution
4-16
Make sure to disconnect the power before working on the IP board.
4. Troubleshooting
Location (Main) - TOP
4-17
4. Troubleshooting
„„ WAVEFORMS

Compnent_Y (Gray scale) / Pb / Pr (Color bar)

LVDS output
4-18
4. Troubleshooting
„„ No Sound
Symptom
Major
checkpoints
-- Video is normal but there is no sound..
-- When the speaker connectors are disconnected or damaged.
-- When the sound processing part of the Main Board is not functioning.
-- Speaker defect..
Check the source and check the connection of
sound cable (Comp/PC/DVI to HDMI) ?
No
Input the sound source properly.
Yes
check the Self Diagnosis
(SupportSelf DiagnosisPicture Test)
Dose the promblem still exist self diagnosis ?
No
Check external devices and
connections.
Yes
Does the sound data appear at
R404/R405 (AV1, COMP1)
No
Check CN403.
Change the Main Assy
No
Change the Main Assy.
No
Check IC1001 (X5N).
Check IC301 (Sound AMP).
Change the Main Assy.
No
Please, Contact Tech support.
Yes
Does the DC B12V
appear at BD301?
Yes

Diagnostics
Does the sound data appear at
- L-, L+, R-, R+ ?
Yes
Replace speaker ?
Caution
Make sure to disconnect the power before working on the IP board.
4-19
4. Troubleshooting
Location (Main) - TOP
4-20
4. Troubleshooting
„„ WAVEFORMS

Speaker out
4-21
4. Troubleshooting
4-2. Factory Mode Adjustments
4-2-1 Entering Factory Mode
• If you do not have Factory remote - control
Power OFF
MUTE
1
8
2
Power ON
• If you do not have Factory remote - control
INFO
Factory
If you don’t have Factory remote control, can’t control some menu.
Option
Control
SVC
T-MX5FAUSC(FHD)/T-MX5HAUSC(HD)
X7-MW-0013
X5-App-0013
OPTION : XXXXXXXX
Expert
ADC : HDMI / COMP / PC / AV
ADC/WB
EDID SUCCESS
HDCP : SUCCESS
Current Flash : Flash 0
Build Date : XX-XX-XXXX
DATE OF PURCHASE : XX/XX/XX
4-22
4. Troubleshooting
4-2-2. Factory Data
Option
Factory Menu Name
Data
Factory Reset
-
Range
Remark
Type
Model
UD5003
UD4003
LD503
LD403
TUNER
ALPS
Audio Amp
TAS5715
Front Color
NONE
Local Set
Other
Exhibition Mode
Off
UD5003/UD4003/LD503/LD403
ALPS/Xugang/SECCustom
TAS5715/NTP3200
Other/S,America
On
Control
Factory Menu Name
Data
Range
Off
On/Off
EDID
EDID ON/OFF
EDID WRITE ALL
Success/Failure
EDID WRITE PC
Success/Failure
EDID WRITE DVI
Success/Failure
EDID WRITE HDMI1
Success/Failure
EDID WRITE HDMI2
Success/Failure
EDID WRITE HDMI3
Success/Failure
EDID WRITE HDMI4
HDMI 1.3/HDMI1/2
EDID VERSION
Sub Option
Mute Time(VIDEO)
4
0ms~1000ms
ready
Failure
Debug/Login/UART
HotPlug
On
ON/OFF
Hotplugcontrol
On
0~255
Spread Spectrum
On
On/Off
Period
60K
40K/50K/60K
Amplitude
2
0/0.5/1/1.5/2
DDR Spread
2%
Off/1%/2%
Auto Power
On
Arab
Off
NT Conversion
Off
Mirror
ON(Middle) / OFF(Small)
Spread Spectrum
ON(Middle) / OFF(Small)
4-23
4. Troubleshooting
HDMI EQ1
Middle
Low/Middle/High/Strong
HDMI EQ2
Middle
Low/Middle/High/Strong
HDMI EQ3
Middle
Low/Middle/High/Strong
HDMI EQ4
Middle
Low/Middle/High/Strong
EER Count
2230
WM Calib
Panel Enter Key
Panel Display Time
Checksum
XXXX
View Log
Font Data Viewer
Dimm Type
EXT
EXT/INT
Gamma
0.88
0.88/0.90/0.93/0.95/0.98/Off
Carrier Mute
Off
On/Off
Anynet+
Off
On/Off
High Devi
Off
On/Off
Volume Cureve
NT
NT/EU/EA
HotPlug Delay
3
0~63
HP Ident
Low
High/Low
PC Ident
On
On/Off
Watchdog
On
On/Off
LVDS Format
JEIDA /
VESA(19D4003.32D403)
JEIDA / VESA
OSD Resolution
1366*768
HPD Polarity
Info Live
Bus Stop
OTA Code
OTA Duration Test
Alternate Del
Ignore VCT Version
On
On/Off
Change OSD Language
KOR
ENG/KOR
VCR Mode
Off
On/Off
Shop Mode
OFF
ON/OFF
Shop Mode
OFF
ON/OFF
PDP Option
Hotel Option
Shop Option
USB DEMO ON(SEC)
USB DEMO OFF(SEC)
Sound
4-24
4. Troubleshooting
BD Mode
A2K Prescale
20
0~40
BTSC Mono Prescale
20
0~40
BTSC streo Prescale
20
0~40
SAP Prescale
20
0~40
BTSC M2S Threshold
0x80
0xA0~0x9F
BTSC S2M Threshold
0x70
0xA0~0x9F
Carrier Mute Thr High
0x39
0x00~0x7F
Carrier Mute Thr Low
0x26
0x00~0x7F
MP3 Level
-6dB
-12dB~0dB
Master Vol
16
0~255
PWM Modulation
85
0~255
DRC1 Threshold
0x35
0x00~0x7F
DRC2 Threshold
0x23
0x00~0x7F
SPEAKER EQ
On
On/Off
SC1 Vol
16
0~255
SC2 Vol
16
0~255
Audio Delay
20ms
0~150ms
[Edu] SPK Level
1
0~8
[Edu] MIC Level
1
0~8
[Edu] PGA Gain
2dB
0~59dB
EQ Check Sum
0xFA9C
BTSC Pilot NSR On Thr
BTSC Pilot NSR Off Thr
BTSC Stereo On Thr
BTSC Stereo Off Thr
SAP Amp On Thr
SAP Amp Off Thr
SAP NSR On Thr
SAP NSR Off Thr
Carrier Mute Amp On Thr
Carrier Mute Amp Off Thr
Carrier NSR On Thr
Carrier NSR Off Thr
SUB AMP Master Vol
SUB AMP PWM Mod
SUB DRC Thresh
SUB Speaker EQ
Config Option
Num of AV
1
0~3
Num of SVIDEO
0
1~3
4-25
4. Troubleshooting
Num of Comp
1
1~3
Num of HDMI
2
0~4
Num of SCART
0
DVI Sound
1
0~1
HeadPhone
0
0~1
On
On/Off
Off
Off/1~13
Off
Off/1~31
Data
Range
Mode
Off
On/Off
Color Mode
Movie
Color Tone
Cool
Msub Brigh
128
Msub Contr
128
W1_RGAIN
138
W1_BGAIN
104
W1_ROFFS
130
W1_BOFFS
127
W2_RGAIN
131
W2_BGAIN
64
W2_ROFFS
133
W2_BOFFS
129
W3_RGAIN
128
W3_BGAIN
128
W3_ROFFS
128
W3_BOFFS
128
N_RGAIN
131
N_BGAIN
122
N_ROFFS
128
N_BOFFS
129
Movie Countr
100
Movie Brigh
45
Movie Color
55
Num of USB Port
LNA SUPPORT
MFT Offset
Test Pattern
Master Test Pattern
FBE Test Pattern
LOGIC Test Pattern
Advanced
Factory Menu Name
PBE
WM Movie
4-26
Remark
4. Troubleshooting
Movie Sharp
55
Movie Tint
50
Movie BkLight
10
M.Gamma
Off
M_Sub Gamma
0
EPA Standard
Std Contr
100
0~100
Std Bright
45
0~100
Std Sharp
50
0~100
Std Color
50
0~100
Std Tint
50
0~100
Std Backight
8
0~10
RF dB1 Level
4
0~255
RF dB2 Level
6
0~255
RF dB3 Level
10
0~255
RF dB4 Level
20
0~255
Power Key Protect
Off
On/Off
UART Select
Auto Wall
Auto Wall/Debug/MDC/On1/On2
Debug Mode
Debug Off
Debug Off/Debug Smart/Debug RunTime
ADJUST
Dynamic Dimming
LNA Plus
LNA Plus
Back End Mute
PDP FRC
VisualTEST Plus
Disable
Standby Mode Time
45 Min
Delete alt.ver
2 Flash
OTA confirm Time
90 Min
3 Min/90 Min
OTA limit Time
3 Hour
3 Min/3Hour
Dynamic CE
Off
On/Off
FWC
Off
On/Off
1080p 48Hz
On
On/Off
PWM Max
100
1~100
DTV LNA
Auto
On/Off
HDCP Download
Off
On/Off
USB Download
Off
On/Off
PAL BG
1
0~3
PAL DK
1
0~3
2 Min/45 Min
Quick Start
YC_Delay
4-27
4. Troubleshooting
PAL I
1
0~3
SECAM BG
4
0~3
SECAM DK
4
0~3
SECAML
4
0~3
NTSC 358
1
0~3
NTSC 443
0
0~3
AV PAL
1
0~3
AV SECAM
4
0~3
AV NT358
1
0~3
AV NT443
1
0~3
AV PAL60
1
0~3
H1 GAIN
0X12
0X00~0XFF
H2 GAIN
0X08
0X00~0XFF
H3 GAIN
0X08
0X00~0XFF
H4 GAIN
0X08
0X00~0XFF
V1 GAIN
0X10
0X00~0XFF
V2 GAIN
0X0E
0X00~0XFF
H OVERSHOOT
0X20
0X00~0XFF
V OVERSHOOT
0X20
0X00~0XFF
H UNDERSHOOT
0X20
0X00~0XFF
V UNDERSHOOT
0X20
0X00~0XFF
CORING TH2
0X01
0X01~0X0F
CORING TH1
0X01
0X01~0X0F
SKIN_X
0X00
0X00~0XFF
SKIN_Y
0X01
0X00~0XFF
B_SLOPE
0X8A
0X00~0XFF
DLC_ML
0X90
0X00~0XFF
DLC_MH
0X90
0X00~0XFF
DLC_H
0XEB
0X00~0XFF
SKIN_SAT
0X00
0X00~0XFF
SKIN_HUE
0X20
0X00~0XFF
M_SKIN_HUE
0X40
0X00~0XFF
M_SKIN_X
0X00
0X00~0XFF
M_SKIN_Y
0X00
0X01~0X0F
MID_COLOR_LEVEL
0XB8
0X01~0X0F
M_MID_COLOR_LEVE
0X95
0X01~0X0F
7.5 IRE NTSC
OFF
ON/OFF
7.5 IRE OFFSET
16
0~60
SHARPNESS
PE
PQ OTHERS
4-28
4. Troubleshooting
COLOR SPACE
RED SAT
0X12
0X00~0XFF
RED HUE
0X40
0X00~0XFF
GREEN SAT
0X16
0X00~0XFF
GREEN HUE
0X70
0X00~0XFF
BLUE SAT
0X1A
0X00~0XFF
BLUE HUE
0X70
0X00~0XFF
CYAN SAT
0X16
0X00~0XFF
CYAN HUE
0X40
0X00~0XFF
MAGENTA SAT
0X16
0X00~0XFF
MAGENTA HUE
0X40
0X00~0XFF
YELLOW SAT
0X0F
0X00~0XFF
YELLOW HUE
0X70
0X00~0XFF
FWC BLUE
0X0F
0X00~0XFF
FWC RED
0X0F
0X00~0XFF
EEPROM RESET
OFF
ON/OFF
NVR ALL CLEAR
OFF
ON/OFF
Factory Menu Name
Data
Range
N/D ADJ
OFF
ON/OFF
SOURCE
CURRENT
EEPROM RESET
EXPERT
Remark
SVC
Factory Menu Name
Data
Range
MODE
DYNAMIC
DYNAMIC/MOVIE
SCC ON/OFF
OFF
ON/OFF
HX
272
0~1024
HY
278
0~1024
LX
272
0~1024
LY
278
0~1024
SSCC HX
554
0~1024
SSCC HY
573
0~1024
SSCC LX
550
0~1024
SSCC LY
576
0~1024
PSCC CONST
…
PSCC HX
554
0~1024
PSCC HY
573
0~1024
PSCC LX
550
0~1024
Remark
SCC INPUT DATA
SSCC CONST
4-29
4. Troubleshooting
PSCC LY
576
0~1024
SCC SOURCE DATA
PBA
PBA/PANEL
SWAP
PBA
PBA/PANEL
1st_AV_Low
64
0 ~ 1020
1st_AV_High
880
0 ~ 1020
1st_AV_Delta
2
0~7
1st_COMP_Y_Low
64
0 ~ 1020
1st_COMP_Cb_Low
…
1st_COMP_Cr_Low
…
1st_COMP_Y_High
940
1st_COMP_Cb_High
…
1st_COMP_Cr_High
…
1st_COMP_Delta
2
0~7
1st_PC_R_Low
16
0 ~ 1020
1st_PC_G_Low
…
1st_PC_B_Low
…
1st_PC_R_High
1004
1st_PC_G_Low
…
1st_PC_B_Low
…
1st_PC_Delta
2
0~7
2nd_AV_R_Low
4
fixed
2nd_AV_G_Low
4
fixed
2nd_AV_B_Low
4
fixed
2nd_AV_R_High
940
fixed
2nd_AV_G_High
940
fixed
2nd_AV_B_High
940
fixed
2nd_AV_Delta
2
0~7
2nd_COMP_R_Low
4
fixed
2nd_COMP_G_Low
4
fixed
2nd_COMP_B_Low
4
fixed
2nd_COMP_R_High
940
fixed
2nd_COMP_G_High
940
fixed
2nd_COMP_B_High
940
fixed
2nd_COMP_Delta
2
0~7
2nd_PC_R_Low
4
fixed
2nd_PC_G_Low
4
fixed
2nd_PC_B_Low
4
fixed
2nd_PC_R_High
940
fixed
2nd_PC_G_High
940
fixed
2nd_PC_B_High
940
fixed
PANEL AUTO SETTING
4-30
0 ~ 1020
0 ~ 1020
4. Troubleshooting
2nd_PC_Delta
2
0~7
2nd_HDMI_R_Low
4
fixed
2nd_HDMI_G_Low
4
fixed
2nd_HDMI_B_Low
4
fixed
2nd_HDMI_R_High
940
fixed
2nd_HDMI_G_High
940
fixed
2nd_HDMI_B_High
940
fixed
2nd_HDMI_Delta
2
0~7
1st_Y_GH
0
fixed
1st_Y_GL
0
fixed
1st_Cb_BH
0
fixed
1st_Cb_BL
0
fixed
1st_Cr_RH
0
fixed
1st_Cr_RL
0
fixed
2nd_R_L
134
0 ~ 255
2nd_G_L
134
0 ~ 255
2nd_B_L
134
0 ~ 255
2nd_R_H
49
0 ~ 255
2nd_G_H
49
0 ~ 255
2nd_B_H
49
0 ~ 255
Sub Brightness
128
0 ~ 1023
R_Offset
512
0 ~ 1023
G_Offset
512
0 ~ 1023
B_Offset
512
0 ~ 1023
Sub Contrast
128
0 ~ 1023
R_Gain
512
0 ~ 1023
G_Gain
512
0 ~ 1023
B_Gain
512
0 ~ 1023
Movie R Offset
…
fixed
Movie B Offset
…
fixed
Movie R Gain
…
fixed
Movie B Gain
…
fixed
ADC Result
WB
4-31
4. Troubleshooting
4-3. White Balance - Calibration
4-3-1. White Balance -Calibration
Factory
ADC / WB
AV Calibration
Comp Calibration
PC Calibration
HDMI Calibration
4-3-2. Service Adjustment
You must perform Calibration in the Lattice Pattern before adjusting the White Balance.
 Color Calibration
Adjust spec.
1. Source : HDMI
2. Setting Mode : 1280*720@60Hz
3. Pattern : Pattern #24 (Chess Pattern)
4. Use Equipment : CA210 & Master MSPG925 Generator
Use other equipment only after comparing The result with that of The Master equipment.
Input mode
Calibration
Pattern
CVBS IN (Model_#1)
Perform in NTSC B&W Pattern #24
Lattice
Component IN (Model_#6)
Perform in 720p B&W Pattern #24
Lattice
PC Analog IN (Model_#21)
Perform in VESA XGA (1024x768) B&W Pattern #24
Lattice
HDMI IN
Perform in 720p B&W Pattern #24
Lattice
4-32
4. Troubleshooting
„„ Method of Color Calibration (AV)
1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port.
2) Press the Source key to switch to “AV1” mode.
3) Enter Service mode.
4) Select the “ADC” menu.
5) Select the “AV Calibration” menu.
6) In “AV Calibration Off” status, press the “ ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “AV Calibration” status from Failure to Success.
„„ Method of Color Calibration (Component)
1) Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port.
2) Press the Source key to switch to “Component1” mode.
3) Enter Service mode.
4) Select the “ADC” menu.
5) Select the “Comp Calibration” menu.
6) In “Comp Calibration Off” status, press the “ ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “Comp Calibration” status from Failure to Success.
„„ Method of Color Calibration (PC)
1) Apply the VESA XGA Lattice (N0. 21) pattern signal to the PC IN port.
2) Press the Source key to switch to “PC” mode.
3) Enter Service mode.
4) Select the “ADC” menu.
5) Select the “PC Calibration” menu.
6) In “PC Calibration Off” status, press the “ ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “PC Calibration” status from Failure to Success.
„„ Method of Color Calibration (HDMI)
1) Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port.
2) Press the Source key to switch to “HDMI1” mode.
3) Enter Service mode.
4) Select the “ADC” menu.
5) Select the “HDMI Calibration” menu.
6) In “HDMI Calibration Off” status, press the “ ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “HDMI Calibration” status from Failure to Success.
4-3-3. White Balance - Adjustment
Factory
ADC / WB - White Balance
(Low light)
(High light)
Sub Bright
Sub Contrast
R offset
R gain
G offset
G gain
B offset
B gain
4-33
4. Troubleshooting
4-4. White Ratio (Balance) Adjustment
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to
adjust these in CVBS, Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default. (Refer to Table 1, 2)
It varies with Panel’s size and Specification.
- Equipment : CS-210
- Pattern: MIK K-7256 #92 “Flat W/B Pattern" as standard
- Use other equipment only after comparing the result with
that of the Master equipment.
- Set Aging time : 60min
- Calibration and Manual setting for WB adjustment.
HDMI : Calibration at #24 Chessboard Pattern
Manual adjustment #92 pattern (720p)
COMP: Calibration at #24 Chessboard Pattern
Manual adjustment at #92 pattern (720p)
CVBS: Calibration at #24 Chessboard Pattern
Manual adjustment at #92 pattern (NTSC)
- If finishing in HDMI mode, adjustment coordinate is almost same in AV/COMP mode.
- White Balance Manual Adjustment
4-34
4. Troubleshooting
 UN19D4003BD
Adjustment Coordinate CA-210
P-Mode
[Dynamic Cool1]
HDMI
Comp
CVBS
[Movie Warm2]
HDMI
Comp
CVBS
x
y
Y(Luminance)
T(K)+MPCD
10,000 (+/- 0)
H/L
281
288
R-Gain : 132
B-Gain : 154
Sub_CT : 128
L/L
-
-
(Sub_Brt:128 Fix)
R-Offset, B-Offset : 128
-
H/L
-
-
(M-Sub_CT:128 Fix)
appiled Movie W2 R/B-gain
-
L/L
-
-
(M-Sub_Brt:128 Fix)
appiled Movie W2 R/B-gain
-
x
y
Y(Luminance)
T(K)+MPCD
H/L
264
274
30.1 fL
(Sub_CT:133 Fix)
12,000 (±0)
L/L
-
-
1.8 fL
(Sub-Brt:128 Fix)
-
H/L
319
340
- fL
(M_Sub_CT:128 Fix)
6,500(+-0)
L/L
-
-
- fL
(M_Sub_CT:128 Fix)
-
 UN26D4003BD
Adjustment Coordinate CA-210
P-Mode
[Dynamic Cool1]
HDMI
Comp
CVBS
[Movie Warm2]
HDMI
Comp
CVBS
 UN32D4003BD
Adjustment Coordinate CA-210
P-Mode
[Dynamic Cool1]
HDMI
Comp
CVBS
[Movie Warm2]
HDMI
Comp
CVBS
x
y
Y(Luminance)
T(K)+MPCD
12,000 (±0)
H/L
264
274
31.8 fL
(Sub_CT:136 Fix)
L/L
-
-
1.8 fL
(Sub-Brt:128 Fix)
-
H/L
319
340
- fL
(M_Sub_CT:128 Fix)
6,500(+-0)
L/L
-
-
- fL
(M_Sub_CT:128 Fix)
-
x
y
Y(Luminance)
T(K)+MPCD
H/L
264
274
31.8 fL
(Sub_CT:136 Fix)
12,000 (±0)
L/L
-
-
1.8 fL
(Sub-Brt:128 Fix)
-
H/L
319
340
- fL
(M_Sub_CT:128 Fix)
6,500(+-0)
L/L
-
-
- fL
(M_Sub_CT:128 Fix)
-
 UN22D5003BF
Adjustment Coordinate CA-210
P-Mode
[Dynamic Cool1]
HDMI
Comp
CVBS
[Movie Warm2]
HDMI
Comp
CVBS
4-35
4. Troubleshooting
 LN32D40*E*D
Adjustment Coordinate CA-210
P-Mode
[Dynamic Cool1]
HDMI
Comp
CVBS
[Movie Warm2]
HDMI
Comp
CVBS
4-36
x
y
Y(Luminance)
T(K)+MPCD
12,000 (±0)
H/L
272
278
38.0 fL
(Sub_CT:134 Fix)
L/L
272
278
2.2 fL
(Sub-Brt:128 Fix)
12,000 (±0)
H/L
306
327
- fL
(M_Sub_CT:128 Fix)
6,500 (±0)
L/L
306
327
- fL
(M_Sub_CT:128 Fix)
6,500 (±0)
4. Troubleshooting
4-5. Software Upgrade
Software Upgrade can be performed by downloading the latest firmware from samsung.com to a USB memory device.
Current Version - the software already installed in the TV.
 Note : Software is represented as ‘Year/Month/Day_Version’.
4-5-1. How to check the SW version
Use the main menu
1. Click the “menu” key in remote controler.
2. Select Support menu.
3. Locate the menu cursor “Software Upgrade” menu.
4. Click the “info” key.
5. Check the Main SW and Micom version.
Use the factory mode
 Access the factory mode
Option
Control
SVC
T-MX5FAUSC(FHD)/T-MX5HAUSC(HD) : SW Ver,
X7-MW-0013
X5-App-0013
OPTION : XXXXXXXX
Expert
ADC : HDMI / COMP / PC / AV
ADC/WB
EDID SUCCESS
Advanced
HDCP : SUCCESS
Current Flash : Flash 0
Build Date : XX-XX-XXXX
DATE OF PURCHASE : XX/XX/XX
4-37
4. Troubleshooting
4-5-2. How to Upgade SW and Micom
Insert a USB drive containing the firmware upgrade downloaded from samsung.com into the TV.
Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will
turn off and turn on automatically after completing the firmware upgrade. Please check the firmware version after the
upgrades are complete (the new version will have a higher number than the older version). When software is upgraded,
video and audio settings you have When software is upgraded, video and audio settings you have you write down your
settings so that you can easily reset them after the upgrade.
„„ Main SW upgrade
1. S
tore the sw program named "T-MX5FAUSC"(FHD) or
"T-MX5HAUSC"(HD) in USB memory stick.
-- Connect the USB.
2. Click the MENU key in remote controler.
3. Select Support menu.
-- Locate the menu cursor Software Upgrade menu.
4. Click the ENTER key.
5. Click the ENTER key.
-- Wait for upgrade complete and check the SW version.
4-38
4. Troubleshooting
4-6. Rear Cover Dimension
Cover-Rear Area
1
2
3
4
5
6
19D4003
121.8
203.5
51.8
67.5
75.0
75.0
26D4003
166.0
68.0
82.7
378.0
200.0
200.0
32D4003
183.4
80.3
142.1
496.4
200.0
200.0
22D5003
157.6
268.8
53.8
68.8
75.0
75.0
40D5003
236.3
159.4
196.6
604.7
200.0
200.0
32D40*
235.8
50.7
125
542.7
200
200
4-39
5. Wiring Diagram
5. Wiring Diagram
5-1. Wiring Diagram
UN26D4003BD_UN32D403BD
PANEL
Main Board
CN801
CNI802
IP Board
CN201
CN1601
CN1202 CN301
Speaker
CN1
FUNCTION& IR
PANEL
Speaker
UN22D5003BF_UN19D4003BD
T-CON
SMPS
CNM801
CN1801
CN1602
CN202
CN1202 CN301
Main Board
PANEL
CN1
Speaker
Speaker
Function
5-1
5. Wiring Diagram
UN40D5003BF
PANEL
Main Board
CN801
CNI802
IP Board
CN203
CN1604
CN1202 CN301
Speaker
CN1
T-CON
Speaker
FUNCTION& IR
LN32D40*E*D
CNI802
Main CN203
Board CN1601
CN1202
CN801
IP Board
CN301
Speaker
Speaker
CN1
Function&IR
5-2
PANEL
Driver
5. Wiring Diagram
5-2. Position of Connector
5-2-1. UN19D4003BD
1 CN1604_S_HD
2 CN201_S_LED (to Powr board)
9 CN1502 (USB1)
7 CN502 (HDMI1)
8 CN503 (HDMI2)
6 CN403(COMPONETN)
3 CN1201 (FUNCTION)
5 CN1203(DEBUG)
4 CN301 (SPEAKER)
„„ Connector
1 CN1604_S_HD
2 CN201_S_LED (to Powr board)
1
PANEL_VCC
16
ODD_CLK+
1
B5V
8
GND
2
PANEL_VCC
17
ODD_CLK-
2
SW_POWER
9
B12VS
3
PANEL_VCC
18
GND
3
B5V
10
SW_INVERTER
4
PANEL_VCC
19
ODD2+
4
A5V
11
B13V
5
PANEL_VCC
20
ODD2-
5
GND
12
NC
6
GND
21
GND
6
GND
13
B13V
7
GND
22
ODD1+
7
B12VS
14
PWM_DIMM
8
GND
23
ODD1-
9
WP_PANEL
24
GND
10
LVDS FORMAT
25
ODD0+
11
NC
26
ODD0-
12
GND
27
GND
13
ODD3+
28
SDA
14
ODD3-
29
SCL
15
GND
30
NC
3 CN1201 (FUNCTION)
1
B5V
8
GND
2
SW_POWER
9
B12VS
3
B5V
10
SW_INVERTER
4
A5V
11
B13V
5
GND
12
NC
6
GND
13
B13V
7
B12VS
14
PWM_DIMM
1
R+
3
L+
2
R-
4
L-
4 CN301 (SPEAKER)
5-3
5. Wiring Diagram
5 CN1203(DEBUG)
1
GND
4
DEBUG_TX
2
DEBUG_RX
5
DEBUG_TX
3
DEBUG_TX
6
GND
6 CN403(COMPONETN)
1
GND
9
GND
2
COMP1_Y
10
GND
3
IDENT_AV
11
SL
4
GND
12
SR
5
PB
13
GND
6
IDENT_COMP
14
SR
7
GND
15
SL
8
PR
7 CN502 (HDMI1)
1
HDMI1_RX2+
11
GND
2
GND
12
HDMI1_RXCLK-
3
HDMI1_RX2-
13
HDMI_CEC
4
HDMI1_RX1+
14
GND
5
GND
15
SCL
6
HDMI1_RX1-
16
SDA
7
HDMI1_RX0+
17
GND
8
GND
18
5V
9
HDMI1_RX0-
19
HPD
10
HDMI1_RXCLK+
8 CN503 (HDMI2)
1
HDMI2_RX2+
11
GND
2
GND
12
HDMI2_RXCLK-
3
HDMI2_RX2-
13
HDMI_CEC
4
HDMI2_RX1+
14
GND
5
GND
15
SCL
6
HDMI2_RX1-
16
SDA
7
HDMI2_RX0+
17
GND
8
GND
18
5V
9
HDMI2_RX0-
19
HPD
10
HDMI2_RXCLK+
1
USB_VCC
3
USB_DP
2
USB_DM
4
GND
9 CN1502 (USB1)
5-4
5. Wiring Diagram
5-2-2. UN32D4003BD_UN26D4003BD
2 CN202_L_LED (to Powr board)
9 CN1502 (USB1)
7 CN502 (HDMI1)
8 CN503 (HDMI2)
1 CN1602_L_HD
6 CN403(COMPONETN)
3 CN1201 (FUNCTION)
5 CN1203(DEBUG)
4 CN301 (SPEAKER)
„„ Connector
1 CN1602_L_HD
2 CN202_L_LED (to Powr board)
1
PANEL_VCC
16
ODD_CLK+
1
B5V
8
GND
2
PANEL_VCC
17
ODD_CLK-
2
SW_POWER
9
B12VS
3
PANEL_VCC
18
GND
3
B5V
10
SW_INVERTER
4
PANEL_VCC
19
ODD2+
4
A5V
11
B13V
5
PANEL_VCC
20
ODD2-
5
GND
12
NC
6
GND
21
GND
6
GND
13
B13V
7
GND
22
ODD1+
7
B12VS
14
PWM_DIMM
8
GND
23
ODD1-
9
WP_PANEL
24
GND
10
LVDS FORMAT
25
ODD0+
11
NC
26
ODD0-
12
GND
27
GND
13
ODD3+
28
SDA
14
ODD3-
29
SCL
15
GND
30
NC
3 CN1201 (FUNCTION)
1
B5V
8
GND
2
SW_POWER
9
B12VS
3
B5V
10
SW_INVERTER
4
A5V
11
B13V
5
GND
12
NC
6
GND
13
B13V
7
B12VS
14
PWM_DIMM
4 CN301 (SPEAKER)
1
R+
3
L+
2
R-
4
L-
5-5
5. Wiring Diagram
5 CN1203(DEBUG)
1
GND
4
DEBUG_TX
2
DEBUG_RX
5
DEBUG_TX
3
DEBUG_TX
6
GND
6 CN403(COMPONETN)
1
GND
9
GND
2
COMP1_Y
10
GND
3
IDENT_AV
11
SL
4
GND
12
SR
5
PB
13
GND
6
IDENT_COMP
14
SR
7
GND
15
SL
8
PR
7 CN502 (HDMI1)
1
HDMI1_RX2+
11
GND
2
GND
12
HDMI1_RXCLK-
3
HDMI1_RX2-
13
HDMI_CEC
4
HDMI1_RX1+
14
GND
5
GND
15
SCL
6
HDMI1_RX1-
16
SDA
7
HDMI1_RX0+
17
GND
8
GND
18
5V
9
HDMI1_RX0-
19
HPD
10
HDMI1_RXCLK+
8 CN503 (HDMI2)
1
HDMI2_RX2+
11
GND
2
GND
12
HDMI2_RXCLK-
3
HDMI2_RX2-
13
HDMI_CEC
4
HDMI2_RX1+
14
GND
5
GND
15
SCL
6
HDMI2_RX1-
16
SDA
7
HDMI2_RX0+
17
GND
8
GND
18
5V
9
HDMI2_RX0-
19
HPD
10
HDMI2_RXCLK+
1
USB_VCC
3
USB_DP
2
USB_DM
4
GND
9 CN1502 (USB1)
5-6
5. Wiring Diagram
5-2-3. UN22D5003BF
2 CN201_S_LED (to Powr board)
1 CN1603_S_FHD
9 CN1502 (USB1)
7 CN502 (HDMI1)
8 CN503 (HDMI2)
6 CN403(COMPONETN)
5 CN1203(DEBUG)
3 CN1201 (FUNCTION)
4 CN301 (SPEAKER)
„„ Connector
1 CN1603_S_FHD
2 CN201_S_LED (to Powr board)
1
PANEL_VCC
16
ODD_CLK+
1
B5V
8
GND
2
PANEL_VCC
17
ODD_CLK-
2
SW_POWER
9
B12VS
3
PANEL_VCC
18
GND
3
B5V
10
SW_INVERTER
4
PANEL_VCC
19
ODD2+
4
A5V
11
B13V
5
PANEL_VCC
20
ODD2-
5
GND
12
NC
6
GND
21
GND
6
GND
13
B13V
7
GND
22
ODD1+
7
B12VS
14
PWM_DIMM
8
GND
23
ODD1-
9
WP_PANEL
24
GND
10
LVDS FORMAT
25
ODD0+
11
NC
26
ODD0-
12
GND
27
GND
13
ODD3+
28
SDA
14
ODD3-
29
SCL
15
GND
30
NC
3 CN1201 (FUNCTION)
1
B5V
8
GND
2
SW_POWER
9
B12VS
3
B5V
10
SW_INVERTER
4
A5V
11
B13V
5
GND
12
NC
6
GND
13
B13V
7
B12VS
14
PWM_DIMM
4 CN301 (SPEAKER)
1
R+
3
L+
2
R-
4
L-
5-7
5. Wiring Diagram
5 CN1203(DEBUG)
1
GND
4
DEBUG_TX
2
DEBUG_RX
5
DEBUG_TX
3
DEBUG_TX
6
GND
6 CN403(COMPONETN)
1
GND
9
GND
2
COMP1_Y
10
GND
3
IDENT_AV
11
SL
4
GND
12
SR
5
PB
13
GND
6
IDENT_COMP
14
SR
7
GND
15
SL
8
PR
7 CN502 (HDMI1)
1
HDMI1_RX2+
11
GND
2
GND
12
HDMI1_RXCLK-
3
HDMI1_RX2-
13
HDMI_CEC
4
HDMI1_RX1+
14
GND
5
GND
15
SCL
6
HDMI1_RX1-
16
SDA
7
HDMI1_RX0+
17
GND
8
GND
18
5V
9
HDMI1_RX0-
19
HPD
10
HDMI1_RXCLK+
8 CN503 (HDMI2)
1
HDMI2_RX2+
11
GND
2
GND
12
HDMI2_RXCLK-
3
HDMI2_RX2-
13
HDMI_CEC
4
HDMI2_RX1+
14
GND
5
GND
15
SCL
6
HDMI2_RX1-
16
SDA
7
HDMI2_RX0+
17
GND
8
GND
18
5V
9
HDMI2_RX0-
19
HPD
10
HDMI2_RXCLK+
1
USB_VCC
3
USB_DP
2
USB_DM
4
GND
9 CN1502 (USB1)
5-8
5. Wiring Diagram
5-2-4. UN40D5003BF
9 CN1502 (USB1)
7 CN502 (HDMI1)
2 CN202_L_LED (to Powr board)
8 CN503 (HDMI2)
1 CN1601_L_FHD (to Panel)
6 CN403(COMPONETN)
3 CN1201 (FUNCTION)
5 CN1203(DEBUG)
4 CN301 (SPEAKER)
„„ Connector
1 CN1601_L_FHD (to Panel)
1
NC
27
EVEN[0]-
2
NC
28
GND
3
NC
29
ODD[4]+
4
NC
30
5
NC
6
7
8
2 CN202_L_LED (to Powr board)
1
B5V
8
GND
2
SW_POWER
9
B12VS
ODD[4]-
3
B5V
10
SW_INVERTER
31
ODD[3]+
4
A5V
11
B13V
NC
32
ODD[3]-
5
GND
12
NC
FORMAT
33
GND
SDA_Panel
34
ODDCLK+
6
GND
13
B13V
ODDCLK-
7
B12VS
14
PWM_DIMM
9
TCON_WP
35
10
NC
36
GND
11
SDA_Panel
37
ODD[2]+
12
SCL_Panel
38
ODD[2]-
13
GND
39
ODD[1]+
14
EVEN[4]+
40
ODD[1]-
3 CN1201 (FUNCTION)
1
B5V
8
GND
2
SW_POWER
9
B12VS
3
B5V
10
SW_INVERTER
15
EVEN[4]-
41
ODD[0]+
4
A5V
11
B13V
16
EVEN[3]+
42
ODD[0]-
5
GND
12
NC
17
EVEN[3]-
43
GND
18
GND
44
GND
6
GND
13
B13V
19
EVENCLK+
45
GND
7
B12VS
14
PWM_DIMM
20
EVENCLK-
46
NC
21
GND
47
Panel_VCC
22
EVEN[2]+
48
Panel_VCC
23
EVEN[2]-
49
Panel_VCC
24
EVEN[1]+
50
Panel_VCC
25
EVEN[1]-
51
Panel_VCC
26
EVEN[0]+
4 CN301 (SPEAKER)
1
R+
3
L+
2
R-
4
L-
5-9
5. Wiring Diagram
5 CN1203(DEBUG)
1
GND
4
DEBUG_TX
2
DEBUG_RX
5
DEBUG_TX
3
DEBUG_TX
6
GND
6 CN403(COMPONETN)
1
GND
9
GND
2
COMP1_Y
10
GND
3
IDENT_AV
11
SL
4
GND
12
SR
5
PB
13
GND
6
IDENT_COMP
14
SR
7
GND
15
SL
8
PR
7 CN502 (HDMI1)
1
HDMI1_RX2+
11
GND
2
GND
12
HDMI1_RXCLK-
3
HDMI1_RX2-
13
HDMI_CEC
4
HDMI1_RX1+
14
GND
5
GND
15
SCL
6
HDMI1_RX1-
16
SDA
7
HDMI1_RX0+
17
GND
8
GND
18
5V
9
HDMI1_RX0-
19
HPD
10
HDMI1_RXCLK+
8 CN503 (HDMI2)
1
HDMI2_RX2+
11
GND
2
GND
12
HDMI2_RXCLK-
3
HDMI2_RX2-
13
HDMI_CEC
4
HDMI2_RX1+
14
GND
5
GND
15
SCL
6
HDMI2_RX1-
16
SDA
7
HDMI2_RX0+
17
GND
8
GND
18
5V
9
HDMI2_RX0-
19
HPD
10
HDMI2_RXCLK+
1
USB_VCC
3
USB_DP
2
USB_DM
4
GND
9 CN1502 (USB1)
5-10
5. Wiring Diagram
5-2-5. LN32D40*E*D
2 CN204_L_LCD (to Powr board)
9 CN1502 (USB1)
7 CN502 (HDMI1)
8 CN503 (HDMI2)
1 CN1605_SHARP
6 CN403(COMPONETN)
3 CN1201 (FUNCTION)
5 CN1203(DEBUG)
4 CN301 (SPEAKER)
„„ Connector
1 CN1605_SHARP
2 CN204_L_LCD (to Powr board)
1
GND
16
ODD1-
1
B5V
8
GND
2
GND
17
GND
2
SW_POWER
9
B12VS
3
NC
18
ODD0+
3
B5V
10
SW_INVERTER
4
NC
19
ODD0-
4
A5V
11
B13V
5
GND
20
GND
5
GND
12
NC
6
ODD3+
21
NC
6
GND
13
B13V
7
ODD3-
22
LVDS FORMAT
7
B12VS
14
PWM_DIMM
8
GND
23
GND
9
ODD_CLK+
24
GND
10
ODD_CLK-
25
GND
11
GND
26
GND
12
ODD2+
27
PANEL VCC
13
ODD2-
28
PANEL VCC
14
GND
29
PANEL VCC
15
ODD1+
30
PANEL VCC
3 CN1201 (FUNCTION)
1
B5V
8
GND
2
SW_POWER
9
B12VS
3
B5V
10
SW_INVERTER
4
A5V
11
B13V
5
GND
12
NC
6
GND
13
B13V
7
B12VS
14
PWM_DIMM
4 CN301 (SPEAKER)
1
R+
3
L+
2
R-
4
L-
5-11
5. Wiring Diagram
5 CN1203(DEBUG)
1
GND
4
DEBUG_TX
2
DEBUG_RX
5
DEBUG_TX
3
DEBUG_TX
6
GND
6 CN403(COMPONETN)
1
GND
9
GND
2
COMP1_Y
10
GND
3
IDENT_AV
11
SL
4
GND
12
SR
5
PB
13
GND
6
IDENT_COMP
14
SR
7
GND
15
SL
8
PR
7 CN502 (HDMI1)
1
HDMI1_RX2+
11
GND
2
GND
12
HDMI1_RXCLK-
3
HDMI1_RX2-
13
HDMI_CEC
4
HDMI1_RX1+
14
GND
5
GND
15
SCL
6
HDMI1_RX1-
16
SDA
7
HDMI1_RX0+
17
GND
8
GND
18
5V
9
HDMI1_RX0-
19
HPD
10
HDMI1_RXCLK+
8 CN503 (HDMI2)
1
HDMI2_RX2+
11
GND
2
GND
12
HDMI2_RXCLK-
3
HDMI2_RX2-
13
HDMI_CEC
4
HDMI2_RX1+
14
GND
5
GND
15
SCL
6
HDMI2_RX1-
16
SDA
7
HDMI2_RX0+
17
GND
8
GND
18
5V
9
HDMI2_RX0-
19
HPD
10
HDMI2_RXCLK+
1
USB_VCC
3
USB_DP
2
USB_DM
4
GND
9 CN1502 (USB1)
5-12
5. Wiring Diagram
5-3. Connector Functions
Connector
Functions
CN201  IP CN801
Supply main power and dimming signal from IP board to Main Board.
CN1601_FHD/CN1602_HD  T-CON CNF1
The LVDS signal transfered from Main Board to Panel.
5-4. Cables
5-4-1. UD4003_5003
Use
LEAD (Main-IP 14P)
LEAD (IP-PANEL 6P)
Code
19D4003 : BN39-01455L
26D4003 : BN39-01455E
32D4003 : BN39-01455D
22D5003 : BN39-01455E
40D5003 : BN39-01455K
19D4003 : BN39-01465D
22D5003 : BN39-01465C
LEAD (Main-IP 14P)
LVDS (Main - TCON)
40D5003 : BN96-17116M
19D4003 : BN96-18829L
26D4003 : BN96-18829P
32D4003 : BN96-13227X
22D5003 : BN96-18829M
Photo
Use
Code
Photo
5-4-2. LD40*
Use
LEAD (Main-IP 14P)
LEAD (IP-Driver B'D 7P)
LEAD (IP-Driver B'D 7P)
Code
32D40* : BN39-01449A
32D40* : BN39-01448E
LN32D40* : BN96-17545F
Photo
5-13