Workshop equipment should be inspected:
Select one:
a.
by the management
b.
at regular intervals
Well done that answer is correct
c.
at least once a day
d.
by the cleaners
What are detergents mixed with for washing vehicles?
Select one:
a.
Oil
b.
Water
Well done that answer is correct
c.
Soap
d.
Solvents
Communication method should be a very _________ thing.
Select one:
a.
Natural
b.
Careful
c.
Important
Incorrect answer, review this section of the course and try again
d.
Difficult
8.
Select one:
a.
is used to remove ball joints
b.
allows a soft blow without causing damage
Incorrect answer, review this section of the course and try again
c.
is used to replace ball joints
d.
allows a hard blow without causing damage
A 100W bulb, connected to a 12V supply, will draw a current of about:
Select one:
a.
0.8A
b.
8A
Well done that answer is correct
c.
80A
d.
800A
A CAN wiring system will use:
Select one:
a.
three coaxial type wires
Incorrect answer, review this section of the course and try again
b.
a high and low signal
c.
inductive type relays
d.
changeover switches
Following replacement of the transmission fluid filter/screen, it will be necessary to:
Select one:
a.
adjust pump pressure
b.
fit a new sump/pan gasket
c.
drain the transmission fluid
d.
do all of the above
Incorrect answer, review this section of the course and try again
ncorrect adjustment of the stoplight switch may cause the lights to flash as a result of:
Select one:
a.
vibration
b.
poor earth connections
c.
an open circuit switch
Incorrect answer, review this section of the course and try again
d.
fluid pressure
The function of the valve cap is to prevent dirt and grit entering the valve core and:
Select one:
a.
locate the valve core
b.
act as a primary seal
Incorrect answer, review this section of the course and try again
c.
act as a secondary seal
d.
hold the valve core in position
Stub axle steering means that each wheel swivels on its own axis and therefore the
Select one:
a.
wheelbase changes
b.
wheelbase remains constant
c.
centre of gravity changes
Incorrect answer, review this section of the course and try again
d.
centre of gravity is higher
Battery state of charge should be checked with:
Select one:
a.
an ohmmeter
b.
a hydrometer
c.
a calorimeter
d.
an ammeter
In
Adding a regulated charge of exhaust gas to the intake of the engine has the effect of reducing:
Select one:
a.
compression pressure
b.
nitrogen oxides
c.
hydrocarbons
Incorrect answer, review this section of the course and try again
d.
induction pressure
he best way to test a relay is to measure the resistance between the contact terminals while
energising with a 12V supply to pins:
Select one:
a.
30 and 85
b.
30 and 87
c.
85 and 86
Well done that answer is correct
d.
85 and 87
With the ignition switched on, a Hall effect pulse generator in an ignition distributor, will produce an
output voltage when the
Select one:
a.
engine is running
b.
Hall chip is shielded
c.
Hall chip is not shielded
d.
engine is cranking
A 'Rzeppa' joint is most commonly found on:
Select one:
a.
the gearbox output shaft
b.
one end of a driveshaft
Well done that answer is correct
c.
both ends of a propshaft
d.
the gearbox end of a halfshaft
Which of the following is a true statement?
Select one:
a.
voltmeters are connected in the circuit in series
Incorrect answer, review this section of the course and try again
b.
ammeters are connected in parallel to the circuit
c.
ohmmeters should not be connected in a live circuit
d.
all of the above
When compared to battery voltage (12V system), the supply voltage to a motor or bulb should be
within about:
Select one:
a.
5V
b.
0.5V
c.
0.05V
d.
0.005V
A cell on a 12V battery checked with a hydrometer had a reading of 1.200:
Select one:
a.
the cell was overcharged
b.
the cell was discharged
c.
the cell was half charged
d.
the cell was fully charged
I
The type of brake which uses the forward rotation of the drum to assist the application of both
brake shoes is described as:
Select one:
a.
hydraulic leading and trailing shoe
Incorrect answer, review this section of the course and try again
b.
twin-leading shoe
c.
mechanical leading and trailing shoe
d.
twin-trailing shoe