Uploaded by Abdo Shakra

Ultrasonic Testing Procedure Explained Step by Step

advertisement
Ultrasonic Testing Procedure Explained Step-By-Step!
‫!شرح إجراء اختبار الموجات فوق الصوتية خطوة بخطوة‬
With the wisdom of science, we have been able to simplify many aspects of life. Is the ultrasonic
testing procedure something that interests you? The following article contains the steps you need
to perform an ultrasonic test.
The ultrasonic testing procedure satisfies requirements for Ultrasonic evaluations of metallic
welding as specified in the specifications or requirements for the design and manufacture of the
component. Also, related approved weld maps are followed.
Organizations that manufacture products or components must adhere to ultrasonic testing
procedures, which define materials, equipment, personnel qualifications, examination, evaluation,
documentation, and acceptance procedures.
Basic Requirements and Term
Exam coverage (overlapping scans)
For each pass of the search unit during the ultrasonic test procedure, at least 10% of the element’s
dimension shall overlap the scanning direction according to the dimensions of the transducer
(piezoelectric element).
Mobilization of search units
A speed of 6 inches/second (150 millimeters/second) shall be observed for searching units for
examination.
Prepare the surface
During the ultrasonic testing procedure, the surface must be free from lubricants, dirt, residue,
rust, and sharp edges to ensure a smooth procedure.
Equipment
An Ultrasonic testing instrument with pulse echoes will be used to generate frequencies between
1 MHZ and 5 MHZ for the examination.
The equipment will be calibrated for the ultrasonic testing procedure for the examination. The
instrument should meet the linearity of the screen height and the linearity of the amplitude control.
Ultrasonic testing is conducted using a Krautkramer USN-52 Ultrasonic testing instrument (trade
name). The instrument will feature stepped gain control in two-decibel increments or fewer while
performing the ultrasonic testing procedure.
Search Units
There may be only one or two transducers in a search unit. This table outlines how to select the
search unit size.



Straight Beam. (either single or dual crystal)
Angle Beam
Search units with contoured contact wedges may be used to aid ultrasonic coupling.
Screen Height Linearity
In an ultrasonic test procedure, you can display information linearly on any screen from 20% to
80% of the calibrated height within *5% of the full-screen height.
Screen height linearity testing should occur at the beginning and every three months after that
(whichever is less often).
Linguistics of amplitude control
Several ultrasonic test procedures use amplitude controls that are accurate up to 20% of the
nominal amplitude ratio over their useful ranges to measure indications beyond that of the
display’s vertical display.
Approximately every six months or at the beginning of each extended use period, whichever is
less, the amplitude control linearity shall be tested according to the procedure in appendix 2 of
Article 5 of ASME code Sec. V.
Couplant
The motor oil should be SAE 20 or 30, glycerin should be used, and adhesive wallpaper should
be used. Comparing complaints is not permitted. However, the complaint must be used for
auditing and calibration. Those used on austenitic stainless steel may not contain more than 250
ppm of halides (chlorides and fluorides), and those used on nickel-based alloys must not exceed
250 ppm of sulfur.
Material Propagation Angle and Mode
Angle beam probes propagate shear waves in material and have application angles, sizes, and
frequencies related to this.
Wave propagation is carried out by a longitudinal wave in material and its corresponding angle,
size, and frequency for a normal beam probe.
Calibration
Blocks of Calibration: Calibration is carried out with reflectors as primary calibration reflectors.
for equipment calibration. Reflectors for basic calibration may be located within components or
within basic calibration blocks, where V1 and V2 are usually most commonly used (approved
calibration). Moreover, a DAC (distance amplitude correction curve) will also be generated using
basic calibration blocks.
The calibrating blocks are similar to the finished component in terms of metallurgy and materials
or have the equivalent P-number grouping. As per the rule of thumb, materials belonging to Pnumbers 1,3,4 & 5 shall be considered comparable. Furthermore, the surface finish on the block
should also accurately reflect the surface finish of the tested component.
System Calibration
Testing of angle beams




Accurate measurement of distance ranges
Correcting distances and amplitudes
Alignment of positions
Surface notch Measurement of Echo Amplitude in the Basic Calibration Block.
Using an electronic distance amplitude correction device during the ultrasonic testing procedure,
your primary responses should be equalized between 40 and 80% of the full-screen height on the
examination screen.
Straight Beam Calibration


Distance Range Calibration
Distance-Amplitude Correction
When the primary calibration block on the basic calibration block is equalized between 40% and
80% of the full-screen height at the distance range in the test, a distance-amplitude correction
device should be used for electronic correction.
Calibration Confirmation
An initial calibration of the system is required before it is used in the thickness range being
examined. Upon calibration, it is necessary to check the sweep range calibration and distanceamplitude correction.
Distance Range Points
If the point is shifted more than 10% of a sweeping reading or 5% of an entire sweep, the DAC
curve is shifted to the sweep line. If so, note the correction in the examination record and correct
the distance range calibration. Those data sheets that record reflectors shall be voided in the case
of datasheets that record reflectors and a new calibration shall be recorded instead.
During the calibration reassessment, all measured values, since the last valid calibration, will be
corrected based on corrected calibrations, and their values will be updated accordingly.
For calibration or calibration check datasheets, any point on the distance-amplitude correction
curve (DAC) that has decreased by 20% or 2 dB from its original value is void.
The data covered by the voided area will be re-examined, and the new calibration done and
recorded. Further, where an indication on the distance-amplitude correction (DAC) curve
increases by 20% or 2dB since the last valid calibration or calibration check, all recorded data
should be re-evaluated and recalculated.
Examination
General Requirements:







The scanning needs to be done a minimum of two times to the primary reference level at the
gain setting. Apart from this, an evaluation needs to be done regarding the primary reference
level.
A straight beam technique will be used to scan the volumes, and angle beam techniques will
be employed to scan angles perpendicular to the examination surface. Other angle beam pairs
may be used, provided at least a 10o difference between them.
Angle beam method scanning needs to be performed typically from outside the vessel through
the direct contact method. Two beams, angled at a right angle to the welding axis, should
detect angularly oriented reflectors. Furthermore, angle beams should be directed parallel to
the welding axis to find reflectors cross-oriented to the welding axis. The search unit must be
intimidated to let the ultrasonic energy pass via whole weld volumes and the heat-affected zone
(20mm) of base metal.
To measure the angle beam transducer and exit point refraction angle, an IIW standard
calibration block must be undertaken. A refraction angle tolerance of not more than *2o will be
allowed.
Straight Beam Method
A straight beam search unit should always be used before installing an angle beam search unit
when the heat-affected zone and weld can be scanned first.
At least 2t tana (where t=base metal thickness & a=1/2 groove angle) should be scanned
between the adjacent base metals in order to easily detect reflectors that might affect the
interpretation of angle beam results. This scan is not intended for acceptance-rejection
purposes. It shall be recorded where and in what areas such reflectors are located.
Assessment:
A large DAC must be investigated so that standards established by the referencing code can be
applied to the evaluation of the DAC.
Acceptance standard
All imperfections that give out the amplitude more than 20% to that of reference level require an
in-depth inspection so that the operator can examine the shape, the identity, and the location of
every such imperfection. Each imperfection will be assessed as per the accepted standards.
Reports:
This report shall state the extent of the inspections and the location of the recorded reflectors, and
the identification of the operator who carried out each inspection or portion thereof.
The record shall contain the location of each uncorrected area, the response level, the measure,
the depth below the surface, and the classification of reflections that surpasses 50% of the
reference level.
Download