Certificate Number BAS97ATEX1089X Issue 22 Issued 15 July 2021 Page 1 of 8 1 EU - TYPE EXAMINATION CERTIFICATE 2 Equipment or Protective System Intended for use in Potentially Explosive Atmospheres Directive 2014/34/EU BAS97ATEX1089X – Issue 22 3 EU - Type Examination Certificate Number: 3.1 In accordance with Article 41 of Directive 2014/34/EU, EC-Type Examination Certificates referring to 94/9/EC that were in existence prior to the date of application of 2014/34/EU (20 April 2016) may be referenced as if they were issued in accordance with Directive 2014/34/EU. Supplementary Certificates to such EC-Type Examination Certificates, and new issues of such certificates, may continue to bear the original certificate number issued prior to 20 April 2016. 4 Product: Model 3051 Series Pressure Transmitters 5 Manufacturer: Rosemount Incorporated 6 Address: 6021 Innovation Blvd., Shakopee, MN 55379, USA 7 This re-issued certificate extends EC Type Examination Certificate No. BAS97ATEX1089X to apply to product designed and constructed in accordance with the specification set out in the Schedule of the said certificate but having any variations specified in the Schedule attached to this certificate and the documents therein referred to. 8 SGS Fimko Oy, Notified Body number 0598, in accordance with Article 17 of Directive 2014/34/EU of the European Parliament and of the Council, dated 26 February 2014, certifies that this product has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of products intended for use in potentially explosive atmospheres given in Annex II to the Directive. 8.1 The original certificate was issued by The Electrical Equipment Certification Service (UK Notified Body 0600). It, and any supplements previously issued by SGS Baseefa Ltd (UK Notified Body 1180) have been transferred to the supervision of SGS Fimko Oy (EU Notified Body 0598). The original certificate number is retained. The examination and test results are recorded in confidential Report No. See Certificate History 9 Compliance with the Essential Health and Safety Requirements has been assured by compliance with: EN IEC 60079-0: 2018 EN 60079-11: 2012 except in respect of those requirements listed at item 18 of the Schedule. 10 If the sign “X” is placed after the certificate number, it indicates that the product is subject to the Specific Conditions of Use specified in the schedule to this certificate. 11 This EU - TYPE EXAMINATION CERTIFICATE relates only to the design and construction of the specified product. Further requirements of the Directive apply to the manufacturing process and supply of this product. These are not covered by this certificate. 12 The marking of the product shall include the following: II 1 G Ex ia IIC T4/T5 Ga – See Certificate Schedule for markings SGS Fimko Oy Customer Reference No. 0914 Project File No. 21/0371 This document is issued by the Company subject to their General Conditions for Certification Services accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained herein reflects the Company’s findings at the time of their intervention only and within the limits of Client’s instructions, if any. It does not necessarily indicate that the equipment may be used in particular industries or circumstances. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, schedule included, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Fimko Oy Takomotie 8 FI-00380 Helsinki, Finland Telephone +358 (0)9 696 361 e-mail sgs.fimko@sgs.com web site www.sgs.fi Business ID 0978538-5 Member of the SGS Group (SGA SA) BAS-CERT-086 SGS Baseefa Limited is an associate of SGS Fimko OY Tuomas Hänninen SGS Fimko Oy Issue 2 Certificate Number BAS97ATEX1089X Issue 22 Issued 15 July 2021 Page 2 of 8 13 Schedule 14 Certificate Number BAS97ATEX1089X – Issue 22 15 Description of Product The Model 3051 Series Pressure Transmitters is designed to convert process pressure measurements into a 4-20mA HART, Fieldbus / Profibus or FISCO signal. The apparatus contains a number of printed circuit boards consisting of an appropriate terminal block, one or two output boards, a sensor board, a sensor and an optional liquid crystal display all housed in either a polyurethane coated aluminium or stainless-steel enclosure. When the optional display is fitted, the housing cover contains a glass window. External connections to the integral terminal block are made via one of two tapped holes. This certificate covers the Model 3051C, 3051L, 3051H, 3051HT, 3051T, 3051CA, 3001C, 3001CL and 3051CH Pressure Transmitters, which vary in the process connection. The above models can be fitted with either a Standard, Enhanced, or Low Power 4-20mA HART output board, or a Fieldbus output board permitting connection to either Foundation Fieldbus or Profibus PA systems. The Fieldbus variant can alternatively be fitted with a FISCO transient protection board to form a FISCO variant of the Model 3051 Fieldbus Pressure Transmitter. The various models are coded as follows: Model 3051 / 3001 HART Transmitters Model 3051 Enhanced HART Transmitters Model 3051 Low Power HART Transmitters (Excluding Model 3051HT) Model 3051 Fieldbus/Profibus Transmitters Model 3051 Fieldbus FISCO Transmitters (Excluding Model 3051HT) II 1 G Ex ia IIC T4 Ga (-60°C ≤ Ta ≤ +70°C) Ex ia IIC T5 Ga (-60°C ≤ Ta ≤ +40°C) II 1 G Ex ia IIC T4 Ga (-60°C ≤ Ta ≤ +60°C) Model 3051HT HART Transmitter II 1 G Ex ia IIC T4 Ga (-20°C ≤ Ta ≤ +70°C) Ex ia IIC T5 Ga (-20°C ≤ Ta ≤ +40°C) Model 3051HT Fieldbus/Profibus Transmitter II 1 G Ex ia IIC T4 Ga (-20°C ≤ Ta ≤ +60°C) All models of the Model 3051 Series Pressure Transmitters can be alternatively mounted on process connection pipework to form the following Flowmeters: i) ii) iii) Model 3051CFA Integral Orifice Tiered Flowmeter Model 3051CFC Compact Orifice Tiered Flowmeter Model 3051CFP Integral Orifice Tiered Flowmeter Input parameters HART Versions: Ui Ii Pi = 30V = 200mA = 0.9W Ci Li = 0.012µF = 0 Fieldbus/Profibus Versions: Ui = 30V Ci = 0 Ii = 300mA Li = 0 Pi = 1.3W The above parameters must be derived from a linear supply (resistive output) BAS-CERT-086 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2 Certificate Number BAS97ATEX1089X Issue 22 Issued 15 July 2021 Page 3 of 8 FISCO Versions: Ui Ii Pi = 17.5V = 380mA = 5.32W Ci Li = = ≤ 5nF ≤ 10µH The above parameters apply to both Group IIC and IIB and the C i and Li values do not exceed those specified for the FISCO model. 16 Report Number See Certificate History 17 Specific Conditions of Use 1. The apparatus is not capable of withstanding the 500V insulation test required by clause 6.3.12 of EN 60079-11: 2012. This must be taken into account when installing the apparatus. 2. The enclosure may be made of aluminium alloy and given a protective polyurethane paint finish; however, care should be taken to protect it from impact or abrasion in located in Zone 0. 18 Essential Health and Safety Requirements In addition to the Essential Health and Safety Requirements (EHSRs) covered by the standards listed at item 9, the following are considered relevant to this product, and conformity is demonstrated in the report: Clause Subject 1.2.7 LVD type requirements 1.2.8 Overloading of equipment (protection relays, etc.) 1.4.1 External effects 1.4.2 Aggressive substances, etc. 19 Drawings and Documents New drawings submitted for this issue of certificate: Number Sheet Issue Date Description None Current drawings which remain unaffected by this issue: Number Sheet Issue Date Description 02051-3428*1 1 to 5 AF 2/8/17 Shroud, Microboard, Fieldbus, Conventional Tier 1 1 to 4 AL 8/1/18 Shrouded Ass’y, Fieldbus Output Board 3051C 1 03031-0214* 1 to 3 AG 5/17/17 Filter, RFI 03031-1009*2 1 to 6 AV 10/10/18 03031-1017*1 1 to 5 AR 8/22/18 Model 3051 Intrinsically Safe ATEX Configuration, Baseefa/CENELEC Module Housing Ass’y, Intrinsically Safe 2 1 to 4 AE 10/10/18 A2051-3503*1 1 to 6 AB 8/2/18 2051HT and 3051HT Approval Drawing, FM / CSA / ATEX / IECEx Intrinsically Safe Approval Drawing, 4-20mA, Micro Brd #6 1 1 to 6 AB 8/2/18 Approval Drawing 1-5V, Micro Brd #6 1 1 to 3 AB 8/2/18 Approval Drawing LOI Display 02051-3602* 03031-1082* A2051-3507* A2051-3512* BAS-CERT-086 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2 Certificate Number BAS97ATEX1089X Issue 22 Issued 15 July 2021 Page 4 of 8 Number Sheet Issue Date Description A2051-3517*1 1 to 3 AB 8/2/18 Approval Drawing LCD Display A2051-3612*1 1 to 6 AB 8/3/16 Approval Drawing, Fieldbus Output Board, 3051C 1 1 to 6 AC 6/2018 Approval Drawing, Fieldbus, Output Board, 3051 1 1 to 3 AB 8/2/18 Approval Drawing, Fieldbus Terminal Block, 2051 1 1 to 3 AB 8/3/18 Approval Drawing, Std, Low Power Term. Block, 2051 1 1 to 3 AB 8/2/18 Approval Drawing 4-20mA Std, Terminal Block 1 1 to 3 AB 8/3/18 Approval Drawing, Transient, 4-20mA, Terminal Block 1 1 to 5 AB 8/2/18 Approval Drawing 3051HT Sensor Board 1 1 to 4 AB 8/28/18 Approval Drawing Flex Circuit 3051HT, Lo Pressure 1 A3031-0162* 1 to 3 AB 8/2/18 Approval Drawing, 3051C U-Brd 5 Display A3031-0467*1 1 to 4 AB 10/19/18 1 1 to 4 AB 8/3/18 Approval Drawing 3051 Fieldbus Analog Electronics 1 1 to 3 AB 8/3/18 Approval Drawing, 3051 Fieldbus Digital Electronics 1 A3031-0486* 1 to 4 AB 10/19/18 A3031-0583*1 1 to 5 AB 8/2/18 Approval Drawing, Tran Terminal Block, 3051 Fieldbus Approval Drawing Microboard #5, 3051C A3031-0591*1 1 to 3 AB 8/3/18 Approval Drawing 160 Segment LCD Board 1 1 to 3 AC 09/11/18 Approval Drawing, 4-20mA Std Terminal Block 1 1 to 3 AC 9/12/18 Approval Drawing Transient Terminal Block 1 A3031-0692* 1 to 3 AC 09/11/18 A3031-0817*1 1 to 4 AB 8/2/18 Approval Drawing, FISCO Terminal Block, 3051 Fieldbus Approval Drawing, Sensor Board IV A3031-0929*1 1 to 5 AB 8/3/18 Approval Drawing Sensor, 3051 TAC 1 1 to 4 AB 8/3/18 Approval Drawing Sensor Board V 1 1 to 3 AB 8/3/18 Approval Drawing Vortex LCD Board C53585* 1 to 4 AK 1/26/18 SU10768*2 1 to 12 AP 10/5/18 Diode, Zener: Surface Mount I.S. Clamping Diode, SMB (DO-214AA) Approval Drawing, X051XFA, Tiered Flowmeter SU10769*2 1 to 10 AP 5/24/18 Approval Drawing, X051XFC, Tiered Flowmeter 2 1 to 11 AN 9/28/17 Approval Drawing, Model x051xFP, Tiered Flowmeter A2051-3622* A2051-4240* A2051-4234* A2051-4248* A2051-4251* A2088-0602* A2088-0612* A3031-0477* A3031-0481* A3031-0657* A3031-0665* A3031-0969* A8800-7611* 1 SU10770* Approval Drawing, Std Terminal Block, 3051 Fieldbus Drawings marked *1 are associated and held with IECEx BAS 09.0076X Iss. 7, and also associated with IECEx BAS 09.0077X Iss. 7 and BAS00ATEX3105X Iss. 18. Drawings marked *2 are associated and held with IECEx BAS 09.0076X Iss. 7, and also associated with IECEx BAS 09.0077X Iss. 7, IECEx BAS 10.0034 Iss. 6, BAS00ATEX3105X Iss. 18 and Baseefa11ATEX0275 Iss. 5. 20 Certificate History Certificate No. BAS97ATEX1089X BAS97ATEX1089X/1 BAS-CERT-086 Date Comments 24 June 1997 The release of the prime certificate. The associated test and assessment against the requirements of EN 50014 (1992) and EN 50020 (1994) is documented in Test Report No’s. 97(C)0213 & 96(C)0983. 13 October 1998 To permit alternative terminal block configurations, the use of an alternative sensor board (Sensor Board Phase II), a redesign of Microprocessor Board 5 along with minor mechanical and electrical changes as documented in Test Report No. 98(C)0590. SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2 Certificate Number BAS97ATEX1089X Issue 22 Issued 15 July 2021 Page 5 of 8 Certificate No. Date Comments BAS97ATEX1089X/2 26 May 1999 To permit minor modifications to the circuit boards, the use of the Taconite sensor board and drawing information changes. 1) To permit use of alternative sensor boards, minor mechanical modifications and drawing information changes. 2) To permit the use of the apparatus in accordance with EN 50281-1-1: 1998 and EN 50014: 1997. The surface temperature of the enclosure under dust conditions will not exceed 80°C in ambient temperatures of between -20°C & 40°C. The apparatus is now additionally marked: - BAS97ATEX1089X/3 11 January 2001 II 1 GD T 80°C (-20°C ≤ Ta ≤ +40°C) Additional requirements relating to the installation of external connections using certified cable glands and plugging of unused entries using certified blanking plugs added in accordance with the requirements of the above standards. The associated test and assessment documented in Test Report No. 00(C)0337. BAS97ATEX1089X/4 17 July 2001 To permit changes to components, printed circuit boards and drawings. BAS97ATEX1089X/5 12 July 2002 To permit the change of resistor R13 on Microboard 5 to 69.8kΩ, circuit component changes and drawing information changes. BAS97ATEX1089X/6 1 April 2003 To permit minor drawing changes not affecting the original assessment. BAS97ATEX1089X/7 6 February 2004 To permit minor changes to the label drawing. BAS97ATEX1089X/8 17 January 2005 To permit changes to the microboard PCB. BAS97ATEX1089X/9 24 January 2006 To permit minor drawing changes not affecting the original assessment. 9 November 2006 To permit various design changes and the replacement of PCB’s and modules by Model 3051S components to create the Revision 5 Model 3051C/T Pressure Transmitter. The input parameters remain unchanged. BAS97ATEX1089X/10 1) To permit minor electrical and drawing changes not affect the previous assessment. BAS97ATEX1089X/11 18 February 2008 BAS97ATEX1089X/12 8 December 2008 BAS97ATEX1089X Issue 13 30 October 2009 2) To confirm that the Model 3051C Pressure Transmitter have been reviewed against the requirements of EN 60079-0: 2006 and EN 60079-11: 2007 in respect of the differences from EN 50014: 1992 and EN 50020: 1994 and that none of the differences affect this equipment. To permit minor drawing changes not affecting the original assessment. The certificate incorporates previously issued primary & supplementary certificates into one certificate and confirms the current design meets the requirements of EN 61241-0: 2006 & EN 61241-1: 2004 including the revision of the equipment marking in accordance with these standards as documented in Test Report No. 09(C)0090. The certificate also permits: - BAS-CERT-086 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2 Certificate Number BAS97ATEX1089X Issue 22 Certificate No. Issued 15 July 2021 Page 6 of 8 Date Comments 1) The mounting of the Model 3051C Pressure Transmitter on process connection pipework to form the following Flowmeters: i) Model 3051CFA Integral Orifice Tiered Flowmeter ii) Model 3051CFC Compact Orifice Tiered Flowmeter iii) Model 3051CFP Integral Orifice Tiered Flowmeter 2) An additional Condition of Safe Use to be added to the certificate relating to apparatus with polyurethane coated aluminium enclosure and its protection from impact or abrasion when located in a Zone 0 environment. 3) Minor circuit and drawing changes not affecting the original assessment. Drawing No’s 03031-0584, 03031-0592, 03031-0920, 03031-0921 and 03031-0923 are now obsolete. BAS97ATEX1089X Issue 14 28 June 2010 This issue of the certificate permits minor revisions to the certificate’s equipment description and minor drawing changes not affecting the original assessment. BAS97ATEX1089X Issue 15 15 July 2011 This issue of the certificate permits the use of alternative Microboard and terminal block designs and minor drawing changes that do not affect the original assessment. BAS97ATEX1089X Issue 16 23 January 2012 This issue of the certificate permits the use of alternative Microboard and terminal block designs and minor drawing changes that do not affect the original assessment. This issue also confirms that the current design meets the requirements of EN 60079-0:2009 and EN 60079-31:2009. The equipment is now marked Ex ia IIC T5 Ga (-60°C ≤ Ta ≤ +40°C) or T4 Ga (-60°C ≤ Ta ≤ +70°C) Ex t IIIC T50°C T50060°C Da BAS97ATEX1089X Issue 17 15 August 2012 To permit minor drawing changes, the use of an alternative Sensor Board and to combine this certificate with the contents of BAS98ATEX1355X. This issue also confirms that the current design meets the requirements of IEC 60079-0:2011 and EN 60079-11:2012. Dust marking is corrected: Ex ta IIIC T50°C T50060°C Da BAS97ATEX1089X Issue 18 28 March 2013 To permit minor drawing changes not affecting the original assessment. This issue also confirms the current design meets the requirements of EN 60079-0: 2012. The above test and assessment is documented in IECEx ExTR No. GB/BAS/ExTR13.0070/00. This issue of the certificate permits: 1) The use of an alternative Fieldbus / Profibus Microboard in the equipment. BAS97ATEX1089X Issue 19 BAS-CERT-086 27 January 2014 2) Removal of the Revision 5 Model 3051C/T Transmitters from the certification. The Certificate Schedule on page 2 of the certificate was revised to remove reference to the model and the associated certification drawings removed from the above drawing list. SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2 Certificate Number BAS97ATEX1089X Issue 22 Certificate No. Issued 15 July 2021 Page 7 of 8 Date Comments 3) Minor circuit and drawing changes not affecting the original assessment. 4) The removal of the dust certification of the equipment from the certificate. The dust certification is now covered by separate ATEX Certificate No. Baseefa11ATEX0275X. The standards and markings listed on page 1 of the certificate and the Certificate Schedule on page 2 were revised to remove reference to dust certification. 5) The Certificate Schedule on page 2 of the certificate was revised to add reference to the Model 3051 Enhanced & Low Power HART variants of the equipment. This change does not affect the original assessment. The above test and assessment is documented in IECEx ExTR No. GB/BAS/ExTR14.0020/00. This issue of the certificate permits: 1) The fitting of an alternative sensor board and other boards to form the Model 3051HT Pressure Transmitter. These variants of the equipment are of a similar construction, and have the same input parameters and temperature classification, as those previously assessed. The Certificate Schedule was updated to list the 3051HT variants. The drawing lists were updated to list the new assembly drawings and other drawings associated with the variant. BAS97ATEX1089X Issue 20 5 April 2017 2) The removal of the variants of the equipment fitted with Sensor Board 3 from the certification. As a result of this, Drawing Nos 03031-0585, 03031-0586 & 03031-0587 have been made obsolete and the Sensor Board Assembly removed from the parts list on General Assembly Drawing No. 03031-1009. 3) The removal of Model 3051P Pressure Transmitter from the certification. The Certificate Schedule was revised to remove reference to the Model 3051P. 4) Minor circuit and drawing changes not affecting the original assessment. 5) To confirm the current designs of the Model 3051 Series Transmitters has been reviewed against the requirements of EN 60079-0: 2012 + A11: 2013 in respect of the differences from EN 60079-0: 2012, and none of the differences affect the equipment. The standards listed on page 1 of the certificate have been updated. The above test and assessment is documented in IECEx ExTR No. GB/BAS/ExTR16.0191/00. Project File No. 16/0304. This issue of the certificate permits: - BAS97ATEX1089X Issue 21 2 November 2018 1) The fitting of an alternative Fieldbus / Profibus Microboard in the Fieldbus / Profibus and FISCO variants of the Model 3051 Series Pressure Transmitters. The fitting of the alternative board does not affect the input parameters or the certification markings of these variants of the equipment. 2) Minor drawing changes were made to the existing drawings including the introduction of approval drawings for the various boards fitted into the Model 3051 equipment in place of the individual circuit diagram, PCB track layout and PCB Assembly BAS-CERT-086 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2 Certificate Number BAS97ATEX1089X Issue 22 Certificate No. Issued 15 July 2021 Page 8 of 8 Date Comments drawings previously listed. These drawing changes are assessed not to affect the previous assessment of the equipment. Drawing No’s 03031-2008, 03031-2009 & 03031-2011 detailing the AP Sensor are now obsolete and removed from the certification. The above test and assessment are documented in Certification Report No. GB/BAS/ExTR18.0200/00 (Held with IECEx Certificate No. IECEx BAS 09.0076X Iss. 7), Project File No. 18/0232. BAS97ATEX1089X Issue 22 15 July 2021 This issue confirms that the current design meets the requirements of EN IEC 60079-0:2018 and introduces an address change Test Report No. GB/BAS/ExTR21.0108/00, Project File No. 21/0371. For drawings applicable to each issue, see original of that issue. BAS-CERT-086 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 2