Uploaded by Paul Garuba

pdf-122761800-ericsson-field-guide-for-utranpdf

advertisement
Volume II – Ericsson Field Guide for
UTRAN P3: Feature Parameters and Best
Practices
Network Services Document: ND-00150
Rev. 3.0 09/09/2007
Overview
Volume II of the Ericsson Field Guide for UTRAN defines AT&T’s accepted practices for optimization of the
Radio Access portion of the UMTS network for Ericsson WRAN P5MD patch level P5.0.14 (Phase II FOA
exited August 23rd, 2007). The algorithms by which subscriber devices interact with the network are
described in detail. Recommendations are provided that produce the best performance in the network for
each type of interaction.
This Field Guide is composed of 11 sections which include descriptions of:
 New features released in the most recent RNS software version.
 WCDMA design concepts and measurement fundamentals.
 A chronological step by step description of how the subscriber device and network interact. Idle Mode, Call
Establishment and Connected Mode are introduced and the algorithms associated with each are described and
the involved parameters are explained.
 OSS access procedures and methods.
The document concludes with an index and tables wherein all configurable parameters and supporting
details are listed along with a list of well deserved credits.
IMPORTANT: This document is the result of an ongoing collaborative effort between
AT&T Market, Regional, National and Ericsson staff and management. It will continue to
be updated with the latest findings in the areas of optimization and vendor improvement
through the use of Field Studies and successive vendor software and hardware updates.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 1 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Contents
1.
About This Document....................................................................................................................... 8
2.
1.1
Purpose ....................................................................................................................................... 8
1.2
Scope .......................................................................................................................................... 8
1.3
Audience ..................................................................................................................................... 8
1.4
Related Documentation............................................................................................................... 8
1.5
Acronyms and Terms .................................................................................................................. 8
1.6
Trademarks ................................................................................................................................. 8
1.7
Conventions ................................................................................................................................ 8
1.8
Contacts ...................................................................................................................................... 9
New Features in P3 (WRAN P5MD Phase II)................................................................................ 10
2.1
Idle Mode................................................................................................................................... 10
2.1.1
URA_PCH......................................................................................................................... 10
2.1.2 Introduciton of CELL_FACH State for HS capable UEs................................................... 10
2.2
Call Establishment .................................................................................................................... 10
2.2.1 2xPS Radio Access Bearers............................................................................................. 10
2.2.2 Enhanced Uplink (EUL) or HSUPA................................................................................... 10
2.3 Mobility and Connection Management...................................................................................... 10
2.3.1 Introduction of additional R99 RABs................................................................................. 10
2.3.2 Event 6a has been replaced with Event 6d ...................................................................... 11
2.3.3 Code Division Multiplexing for HSDPA ............................................................................. 11
2.3.4 hoTypeDrncBand1-17 has been replaced with defaultHoType........................................ 11
2.3.5 Calculation of maxDlPowerCapability............................................................................... 11
2.3.6 Throughput triggered Dedicated to Dedicated Up and Down-Switch (Uplink and Downlink)
.......................................................................................................................... 11
2.4
OSS Related Functionality ........................................................................................................ 11
2.4.1 Neighbor List Prioritization................................................................................................ 11
3.
Significant KPI Impact Parameters ................................................................................................ 12
3.1
Accessibility............................................................................................................................... 12
3.2
Retainability............................................................................................................................... 12
3.3
Quality ....................................................................................................................................... 12
3.4 Throughput and Latency ........................................................................................................... 12
4.
Design Criteria ............................................................................................................................... 13
4.1
UE Capabilities.......................................................................................................................... 13
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 2 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
4.1.1 Frequency Bands.............................................................................................................. 13
4.1.2 Channel Numbering Scheme (UARFCN) ......................................................................... 13
4.1.3 Power Classes .................................................................................................................. 14
4.1.4 UE Category (HSDPA and EUL) ...................................................................................... 15
4.2
Link Budget ............................................................................................................................... 16
4.3
Basic Design Requirements...................................................................................................... 17
4.3.1 Pilot Pollution .................................................................................................................... 17
4.3.2 Neighbor List Determination ............................................................................................. 17
4.3.3 Scrambling Code Usage................................................................................................... 18
4.4
Measurement Fundamentals .................................................................................................... 18
4.4.1
PCPICH ............................................................................................................................ 18
4.4.2 PCPICH RSCP ................................................................................................................. 19
4.4.3 CPICH Ec/No (Ec/Io) ........................................................................................................ 19
4.4.4
Eb/No ................................................................................................................................ 20
4.4.5
SIR .................................................................................................................................... 20
4.4.6
RSSI.................................................................................................................................. 20
4.4.7 RTWP ............................................................................................................................... 20
4.4.8
5.
BLER................................................................................................................................. 21
Parameters Described Within Context........................................................................................... 22
5.1
Idle Mode................................................................................................................................... 22
5.1.1 Cell Search Procedure...................................................................................................... 22
5.1.2 PLMN Selection ................................................................................................................ 23
5.1.3 IMSI and GPRS Attach ..................................................................................................... 28
5.1.4 Location and Routing Area Updates................................................................................. 34
5.2
Call Establishment .................................................................................................................... 35
5.2.1 Radio Access Bearer ........................................................................................................ 35
5.2.2 Mobile Origination / Termination....................................................................................... 37
5.3 Mobility and Connection Management...................................................................................... 51
5.3.1 Measurement Fundamentals ............................................................................................ 51
5.3.2 Cell Reselection in Idle Mode or CELL_FACH ................................................................. 52
5.3.3 Handover in Connected Mode (CELL_DCH) – Intra-Frequency ...................................... 53
5.3.4 Handover in Connected Mode (CELL_DCH) – Inter-Frequency or Inter-RAT ................. 58
5.3.5
HS Cell Change ................................................................................................................ 70
5.3.6
Channel Switching ............................................................................................................ 71
5.3.7 HSDPA Scheduling........................................................................................................... 86
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 3 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.8 EUL Scheduling ................................................................................................................ 87
5.3.9 Congestion Detection and Resolution .............................................................................. 88
5.3.10 Radio Connection Supervision ......................................................................................... 91
5.3.11Downlink and Uplink Power Control ................................................................................. 91
6.
OSS Overview................................................................................................................................ 98
6.1
Configuration Management....................................................................................................... 99
6.1.1 Configuration Access Procedures .................................................................................... 99
6.1.2 Configuration Methods...................................................................................................... 99
6.2
Performance Management...................................................................................................... 100
6.2.1 Performance Access Procedures ................................................................................... 100
6.2.2 Ericsson Counter Types ................................................................................................. 101
6.2.3 Call Trace Capability....................................................................................................... 101
6.3
Fault Management .................................................................................................................. 102
6.3.1 Alarm Status Matrix ........................................................................................................ 102
6.3.2 Alarm List Viewer ............................................................................................................ 102
6.3.3 Alarm Log Browser ......................................................................................................... 102
7.
Counter and Recording Activation ............................................................................................... 103
7.1
Counter Activation................................................................................................................... 103
7.1.1 Table Definitions ............................................................................................................. 103
7.1.2 Subscription Profiles ....................................................................................................... 103
7.2
Recording Activation ............................................................................................................... 144
7.2.1 Activation of RES Recording to support Scorecard Data ............................................... 144
8.
Reference Documents ................................................................................................................. 145
9.
Parameter Reference................................................................................................................... 146
10.
Consulted List .............................................................................................................................. 159
11.
Index............................................................................................................................................. 166
Figures
Figure 1: Slot and Frame Structure....................................................................................................... 22
Figure 2: Power Ramping on RACH ..................................................................................................... 29
Figure 3: RRC Connection Signaling Flow ........................................................................................... 30
Figure 4: Downlink DPCCH Power ....................................................................................................... 32
Figure 5: Admission Control (Radio Link Request)............................................................................... 40
Figure 6: Admission Control (DL Channelization)................................................................................. 41
Figure 7: Admission Control (Spreading Factor Usage) ....................................................................... 43
Figure 8: Admission Control (DL Power) .............................................................................................. 44
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 4 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 9: Admission Control (Uplink ASE Utilization) ........................................................................... 46
Figure 10: Admission Control (Downlink ASE Utilization)..................................................................... 47
Figure 11: Admission Control (Uplink Hardware Utilization)................................................................. 48
Figure 12: Admission Control (Downlink Hardware Utilization) ............................................................ 49
Figure 13: Event 1a Trigger .................................................................................................................. 54
Figure 14: Event 1b Trigger .................................................................................................................. 55
Figure 15: Event 1c Trigger................................................................................................................... 56
Figure 16: Event 1d Trigger .................................................................................................................. 57
Figure 17: Event 2d Trigger (Begin Compressed Mode) ...................................................................... 59
Figure 18: Event 2f Trigger (Cease Compressed Mode) ...................................................................... 60
Figure 19: Event 6d Trigger (Begin Compressed Mode) ...................................................................... 61
Figure 20: Event 6b Trigger (Cease Compressed Mode)..................................................................... 62
Figure 21: Event 3a (EcNo)................................................................................................................... 64
Figure 22: Event 3a (RSCP) ................................................................................................................. 65
Figure 23: Event 3a (UE Tx) ................................................................................................................. 66
Figure 24: Event 2b (EcNo)................................................................................................................... 67
Figure 25: Event 2b (RSCP) ................................................................................................................. 68
Figure 26: Event 2b (UE Tx) ................................................................................................................. 69
Figure 27: Event 1d HS (HS Cell Change) ........................................................................................... 70
Figure 28: Dedicated (DCH/DCH) to Common Down-Switch............................................................... 73
Figure 29: HS (DCH/HS or EUL/HS) to Common Down-Switch........................................................... 74
Figure 30: Common to Dedicated (DCH/DCH, DCH/HS or EUL/HS) Up-Switch ................................. 75
Figure 31: Common to URA_PCH Down-Switch .................................................................................. 76
Figure 32: URA_PCH to Idle Mode Down-Switch................................................................................. 77
Figure 33: Throughput triggered DCH to DCH Down-Switch (Downlink) ............................................. 78
Figure 34: Throughput triggered DCH to DCH Down-Switch (Uplink) .................................................. 79
Figure 35: Code Power check for Up-Switch (Downlink) ...................................................................... 80
Figure 36: Code Power check for Up-Switch (Downlink) ...................................................................... 81
Figure 37: Throughput Triggered Up-Switch (Uplink) ........................................................................... 82
Figure 38: Covered Triggered Ded. to Ded. Down-Switch ................................................................... 83
Figure 39: Throughput Triggered Down-Switch (Multi-RAB) ................................................................ 84
Figure 40: Throughput Triggered Up-Switch (Multi-RAB) ..................................................................... 85
Figure 41: Throughput Triggered Down-Switch (2xPSMulti-RAB)........................................................ 86
Figure 42: Congestion Detection (Downlink) ........................................................................................ 89
Figure 43: Congestion Detection (Uplink) ............................................................................................. 90
Figure 44: OSS Connectivity................................................................................................................. 98
Tables
Table 1: Operating Bands ..................................................................................................................... 13
Table 2: UARFCN List for Bands II and V (“Additional Channels” method) ......................................... 14
Table 3: UE Power Classes .................................................................................................................. 15
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 5 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Table 4: UE Categories (HSDPA) ......................................................................................................... 15
Table 5: UE Categories (EUL) .............................................................................................................. 16
Table 6: Link Budget ............................................................................................................................. 16
Table 6: Master Information Block (MIB) Contents ............................................................................... 24
Table 7: System Information Block 1 (SIB 1) Contents ........................................................................ 24
Table 8: System Information Block 3 (SIB 3) ........................................................................................ 25
Table 9: System Information Block 5 (SIB 5) ........................................................................................ 25
Table 10: System Information Block 7 (SIB 7) ...................................................................................... 26
Table 11: System Information Block 11 (SIB 11) .................................................................................. 26
Table 12: System Information Block 12 (SIB 12) .................................................................................. 27
Table 13: Air Speech Equivalents (ASE) .............................................................................................. 44
Table 14: Maximum Bit Rates per Radio Link....................................................................................... 92
Table 15: UeRc, RAB and UeRcTrCh Identification ............................................................................. 95
Table 16: blerQualityTarget values ....................................................................................................... 96
Table 17: Configuration Management Access Procedures .................................................................. 99
Table 18: Counter Activation............................................................................................................... 105
Table 19: Configurable Parameter Lookup Table............................................................................... 146
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 6 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Document Revision History
This table identifies content revisions made to this document.
Date
Rev
Revision Description
Writer
Sponsor
11/01/2005
1.0
Release version
Michael
Noah
Adnan Naqvi
11/28/2005
1.1
Updates to “Cingular Recommended” parameter values
based upon Field Optimization.
Michael
Noah
Greg
Scharosch
05/01/2006
2.0
Updates based upon Cingular P2 (Ericsson P5ED) FOA as
well as results from Field Studies
Michael
Noah
Greg
Scharosch
01/25/2007
2.1
Content extended – version not published.
Michael
Noah
Greg
Scharosch
03/30/2007
2.2
Moved to new AT&T template. Incorporated all existing
Field Guide Alerts.
Michael
Noah
Greg
Scharosch
09/09/2007
3.0
Updated for AT&T P3 Phase II (Ericsson P5MD P5.0.14)
Michael
Noah
Somesh
Razdan
RACI
This table identifies RACI team members.
Accountable
Responsible
Somesh Razdan
Michael Noah
Consulted
Informed
Market Engineering
Mike Pietropola
Regional Engineering
Eric Parker
Regional OSS Support
Adnan Naqvi
National Field Support
John Dapper
Strategic Planning
National Quality
Ericsson Support
For details see Consulted_List
Copyright © 2007 AT&T Mobility LLC.
All rights reserved. No part of the contents of this document may be reproduced or transmitted in any
form without the written permission of the publisher.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 7 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
1. About This Document
This section includes information about this document.
1.
Purpose
The primary intention of this document is to serve as a common point of understanding and reference.
This volume includes recommendations for all configurable RNC and Node B parameters. The
recommendations made within this document are the result of collaborative efforts between all groups
involved (see 1.3).
2.
Scope
This document is mainly based upon Ericsson’s UTRAN implementation, focusing on the interaction
between the User Equipment and UTRAN. For completeness, some facets of the Core Network are
included, e.g. Paging, Routing and Location Area Update procedures, i.e. non-access stratum.
3.
Audience
The audience for this document includes AT&T Market, Region and National Engineers and Technicians
responsible for Ericsson UTRAN Optimization and Maintenance.
4.
Related Documentation
See Reference Documents Chapter.
5.
Acronyms and Terms
All acronyms and terms are fully spelled out within the document.
6.
Trademarks
The trademarks used in this document are the property of their respective owners.
7.
Conventions
The following conventions are used throughout this document:
 The term “call” refers to any type of user plane connection between UE and the Core Network. It is not specific to
voice or data - UE originated or terminated. It specifically does not include any type of signaling used to support
the communication of user information.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 8 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 The term “function” refers to Ericsson’s implementation of a certain portion of the 3GPP specification. A function is
limited to satisfying a specific action taken by either the network or UE. For example, the process of originating a
call is referred to as a function. Once the call has been originated, handing the call over is considered a function
and ending the call is a function. Within this document, parameters are explained relative to the functions they
support.
 Each Operator Configurable Parameter expressed in bolditalic. Brackets enclose the Configurable Parameter’s
Level (RNC, Cell, etc.), AT&T Default Value, Units and Class (Policy, Rule, Fixed, Variable).
 Each Operator Configurable Paramter exists within a specifi Managed Opject Class (MOC). The Managed Object
Class will be specified only for parameters that exist within multiple Managed Object Classes. For example,
qOffset1sn is a parameter that can be set differently for Intra-Frequency (UtranRelation) and Inter-RAT
(GsmRelation) neighbors. The parameter instances are therefore denoted as qOffset1sn(UtranRelation) [Nabr,
0, dB, Fixed] and qOffset1sn(GsmRelation) [Nabr, 7, dB, Fixed].
 All references to Radio Access Bearers (RABs) are denoted as UL/DL where UL is the Uplink RLC Data rate in
kilobits per second and DL is the Downlink Data rate in kilobits per second.
 The term “R99” is used to denote all CELL_DCH Radio Access Bearers referring to the release of the specification
that only supported Dedicated Channels (DCH). The term DCH/HS is used to denote HSDPA capability where the
Uplink uses an R99 Radio Access Bearer. The terms EUL/HS or HSPA is used to denote the HSUPA / HSDPA
capability.
 Some configurable parameters include an “(sho)” or an “(hho)” suffix. This suffix is used to specify a subset of
cells to which the parameter recommendation applies. The sho vs. hho distinction is as follows:
(hho). The parameter recommendation is specific to UEs that might have no alternative to performing a Hard
Inter-RAT or Inter-Frequency Handover in order to maintain the call.
(sho). The parameter recommendation is specific to cells that have Intra-Frequency overlap with other 3G
cells. Inter-RAT or Inter-Frequency Hard Handover is not normally needed to maintain the call.
For example, usedFreqThresh2dRscp(hho) [Cell, -106 ±4, dBm, Fixed] is used to indicate the recommended
value of -106 dBm ±4dB is specific to cells that meet the “hho” distinction.
 The terms “Core” and “Border”
Border Cell: Any 3G cell where the antenna orientation points out of a launch cluster or polygon into the 2G
network. With respect to IRAT terminology, these sectors are considered (hho) sectors.
Core Cell: 3G cells within the UMTS polygon that do not qualify as Border Cells. These cells can be designated
as (sho) or (hho) if there are Inter-Frequency borders within the Core. Ideally, there should not be any Inter-RAT
borders within the Core.
1.8
Contacts
For questions or comments about this document's technical content or to request changes to the
document, contact:
Michael Noah, Sr. System Engineer – National Field Support
Desk: 425 580 6716
Wireless: 425 580 6716
E-mail: michael.noah@att.com
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 9 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
2. New Features in P3 (WRAN P5MD Phase II)
This section provides a summary of updates AT&T has elected to implement within this version of RNS
software.
1.
1.
Idle Mode
URA_PCH
The URA_PCH State is now available to all UEs. The URA_PCH State allows the RNS to maintain the
location of the UE within the RNC thereby reducing the Routing Area Update load on the SGSN.
2.
Introduciton of CELL_FACH State for HS capable UEs
The CELL_FACH State is now available to HS capable UEs. Before P5MD, CELL_FACH was only
available to R99 only UEs.
2.
1.
Call Establishment
2xPS Radio Access Bearers
UEs that are able to support multiple Interactive / Background R99 Data RABs are now supported. Speech
+ 2 Data RABs is also supported. For example, you can now use Video Share on your Samsung A707
while it is teathered to your laptop.
2.
Enhanced Uplink (EUL) or HSUPA
Ericsson P5MD introduces Enhanced Uplink (EUL) or HSUPA as specificed in Release 6 of the 3GPP
specification. Enhanced Uplink (EUL) is much like HSDPA in that it allows for greater throughput and
capacity through Link Adaptation. Unlike HSDPA however, EUL does use Macro Diversity and Inner
Loop Power Contorl in the Uplink.
3.
1.
Mobility and Connection Management
Introduction of additional R99 RABs
In P5MD, R99 Radio Access Bearers include 64, 128 and 384 on both the Uplink and Downlink. All
Uplink/Downlink combinations are now supporteded.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 10 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
2.
Event 6a has been replaced with Event 6d
If the UE transmitted power is at maximum for a time equal to timeToTrigger6d, then event 6d occurs
and the UE is commanded to do Compressed Mode measurements.
3.
Code Division Multiplexing for HSDPA
Cells can now support up to 15 High Speed Physical Downlink Shared CHannels (HS-PDSCH).
4.
hoTypeDrncBand1-17 has been replaced with defaultHoType
In P5MD, the Serving RNC determines if UEs will measure Inter-RAT or Inter-Frequency for UEs served
by a Drift RNC by using the defaultHoType [Cell, 1=GSM_PREFERRED, String, Fixed] parameter which
is uarfcnDl [Cell, N/A, Integer, Variable] specific instead of band specific.
5.
Calculation of maxDlPowerCapability
In P5ED, the configurable parameter maximumTransmissionPower [Cell, 400, 0.1dBm, Var.] which sets
the maximum power (downlink capacity) available in the cell at the Reference Point (antenna connector)
was used for Admission Control.
In P5MD, the minimum value of either maximumTransmissionPower [Cell, 400, 0.1dBm, Var.] or
maxDlPowerCapability (a value calculated by the Node B at the Reference Point and sent to the RNC) is
used for Admission Control.
6.
Throughput triggered Dedicated to Dedicated Up and Down-Switch (Uplink and
Downlink)
Throughput based Down-Switch for all R99 RABs on the Uplink and Downlink is now supported.
4.
OSS Related Functionality
1.
Neighbor List Prioritization
It is now possible to re-order neighbor lists without having to remove and re-enter them. This is
accomplished through a new neighbor indexing capability.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 11 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
3. Significant KPI Impact Parameters
Each parameter within this document will to a certain degree impact Key Performance Indicators (KPI).
The following sections describes functions, e.g. Call Establishment, Handover, etc. that have the most
impact on KPIs.
1.
Accessibility
5.1.2.2 Camping on a Suitable Cell
5.1.3.1 Attach Procedure - RACH Ramping and Initial DCH Power Algorithms and Parameters
5.2.2.2 Admission Control
5.3.2 Cell Reselection in Idle Mode or CELL_FACH
3.2
Retainability
2.
Cell Reselection in Idle Mode or CELL_FACH
3.
Handover in Connected Mode (CELL_DCH) – Intra-Frequency
3.3
Quality
5.3.9 Downlink and Uplink Power Control
3.4
Throughput and Latency
5.1.3.1 Attach Procedure - RACH Ramping and Initial DCH Power Algorithms and Parameters
5.2.2.2 Admission Control
5.3.2 Cell Reselection in Idle Mode or CELL_FACH
5.3.9 Downlink and Uplink Power Control
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 12 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
4. Design Criteria
This section mainly covers areas specified in the 3GPP standard. It presents an overview of the spectrum
allocation, UARFCN designation and UE Power Class. A fundamental Link Budget is provided. The rest of
the section provides a high level optimization concept for WCDMA including Pilot Pollution optimization,
neighbor designation guidelines, and a detailed description of the fundamental W-CDMA measurements
CPICH RSCP and CPICH Ec/No.
1.
UE Capabilities
Multiband support for the United States (800/1900 MHz) was not defined until Release 6 of the 3GPP
specification. For this reason, Release 6 is the reference for this section.
1.
Frequency Bands
The frequency bands specified are shown in the table below including the separation (in MHz) between
uplink and downlink frequencies. AT&T operates UMTS at 800 MHz (Band V) and 1900 MHz (Band II).
The rest of the bands listed are included for completeness.
Table 1: Operating Bands
Operating Band
UL Frequencies
DL Frequencies
TX-RX Separation
I
1920 – 1980 MHz
2110 – 2170 MHz
190 MHz
II
1850 – 1910 MHz
1930 – 1990 MHz
80 MHz
III
1710 – 1785 MHz
1805 – 1880 MHz
95 MHz
IV
1710 – 1755 MHz
2110 – 2155 MHz
400 MHz
V
824 – 849 MHz
869 – 894 MHz
45 MHz
VI
830 – 840 MHz
875 – 885 MHz
45 MHz
4.1.2 Channel Numbering Scheme (UARFCN)
The UTRA Absolute Radio Frequency Channel Number allows easy reference to the spectrum allocated
to UMTS. Distinct UARFCNs are used for uplink and downlink frequencies as opposed to a single
UARFCN for a pair of UL/DL frequencies. The UARFCN for the downlink is controlled through uarfcnDl
[Cell, N/A, Integer, Variable] and the uplink UARFCN is controlled through uarfcnUl [Cell, N/A, Integer,
Variable]. A UARFCN occupies 5 MHz of spectrum.
The specification allows for two methods to be used to associate center carrier frequency to UARFCN.
 “General” UARFCN method. Each UARFCN is defined with a specific center frequency. Beginning at 0 Hz, the
UARFCN is incremented by 1 with each increment in frequency of 200 kHz. The UARFCN corresponding to the
center frequency is calculated by finding the product of 5 and the center frequency (in MHz); i.e. UARFCN = 5 *
Frequency (MHz). When using the “general” method, this formula applies regardless of direction (uplink /
downlink) and band.
 “Additional Channels” UARFCN method. The “Additional Channels” are specified according to the table below.
These channels are shifted by 100 KHz relative to the “general” URFCN definition. For Band II, the UARFCN is
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 13 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
calculated by finding the product of 5 and the center carrier frequency (in MHz) minus 1850.1 MHz, i.e UARFCN =
5 * (Frequency in MHz – 1850.1 MHz). For Band V, the UARFCN is calculated by finding the product of 5 and the
center carrier frequency (in MHz) minus 670.1 MHz, i.e UARFCN = 5 * (Frequency in MHz – 670.1 MHz).
Either the “General” or “Additional Channels” method can be used to designate UARFCNs based upon
where you choose to locate UMTS within your licensed spectrum.
Table 2: UARFCN List for Bands II and V (“Additional Channels” method)
UL UARFCN
UL Center
Frequency (MHz)
DL UARFCN
DL Center
Frequency (MHz)
PCS / Cellular
Band
12
1852.5
412
1932.5
PCS – A
37
1857.5
437
1937.5
PCS – A
62
1862.5
462
1942.5
PCS – A
87
1867.5
487
1947.5
PCS – D
112
1872.5
512
1952.5
PCS – B
137
1877.5
537
1957.5
PCS – B
162
1882.5
562
1962.5
PCS – B
187
1887.5
587
1967.5
PCS – E
212
1892.5
612
1972.5
PCS – F
237
1897.5
637
1977.5
PCS – C3
262
1902.5
662
1982.5
PCS – C4
287
1907.5
687
1987.5
PCS – C5
782
826.5
1007
871.5
Cellular – A
787
827.5
1012
872.5
Cellular – A
807
831.5
1032
876.5
Cellular – A
812
832.5
1037
877.5
Cellular – A
837
837.5
1062
882.5
Cellular – B
862
842.5
1087
887.5
Cellular – B
4.1.3 Power Classes
The table below indicates the UE Power Classes specified as of Release 6. Note the maximum power is
the same for all bands within Power Classes 3 and 4. The power in dBm refers to the maximum total
output capability of the UE at the antenna connector and not to the maximum power output of any
particular Physical Channel.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 14 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Table 3: UE Power Classes
Power Class 1
Operating
Band
Power Class 2
Power Class 3
Power Class 4
Power
(dBm)
Tol (dB)
Power
(dBm)
Tol (dB)
Power
(dBm)
Tol (dB)
Power
(dBm)
Tol (dB)
I
+33
+1/-3
+27
+1/-3
+24
+1/-3
+21
+2/-2
II
-
-
-
-
+24
+1/-3
+21
+2/-2
III
-
-
-
-
+24
+1/-3
+21
+2/-2
IV
-
-
-
-
+24
+1/-3
+21
+2/-2
V
-
-
-
-
+24
+1/-3
+21
+2/-2
VI
-
-
-
-
+24
+1/-3
+21
+2/-2
4.1.4 UE Category (HSDPA and EUL)
HSDPA capable UEs are further categorized based upon their throughput capabilities. The table below
includes all of the UE Categories as defined in the 3GPP Specification. Note that Category 11 and 12
UEs only support QPSK. If supportOf16qam [Cell, 1=TRUE, Integer, Fixed] is set to 1=TRUE, then
16QAM is allowed and all categories of UE shown below are supported.
Table 4: UE Categories (HSDPA)
HS-DSCH
Category
Maximum
number of HSDSCH codes
received
Minimum interTTI interval
Maximum number of bits of
an HS-DSCH transport
block received within an
HS-DSCH TTI
Total number of soft
channel bits
Category 1
5
3
7298
19200
Category 2
5
3
7298
2889
Category 3
5
2
7298
2880
Category 4
5
2
7298
38400
Category 5
5
1
7298
57600
Category 6
5
1
7298
67200
Category 7
10
1
14411
115200
Category 8
10
1
14411
134400
Category 9
15
1
20251
172800
Category 10
15
1
27952
172800
Category 11
5
2
3630 QPSK Only
14400
Category 12
5
1
3630 QPSK Only
28800
EUL capable UEs are categorized based upon their throughput capabilities. The table below includes all
of the UE Categories as defined in the 3GPP Specification. The initial UEs in the market are EUL
Category 3.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 15 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Table 5: UE Categories (EUL)
E-DCH Category
Maximum number
of E-DPDCH codes
and SF
Support for 10ms
and/or 2ms TTI
Layer 1 Peak Rate/s
Layer 1 Peak Rate/s
(10ms TTI)
(2ms TTI)
Category 1
One SF4
10ms only
730kb
-
Category 2
Two SF4
Both
1.46mb
1.46mb
Category 3
Two SF4
10ms only
1.46mb
-
Category 4
Two SF4
Both
2.0mb
2.92mb
Category 5
Two SF4
10ms only
2.0mb
-
Category 6
Four (2SF2+2SF4)
Both
2.0mb
5.76mb
4.2
Link Budget
In this simple presentation of the link budget, only the maximum transmit power and receive sensitivity of
the Node B and UE at their respective antenna connectors is considered. The difference between the
maximum transmit power of one node and the maximum receive sensitivity at the other node is
considered to be the maximum allowable path loss. The resulting uplink and downlink path losses are
compared resulting in a difference in dB between the uplink and downlink maximum path losses.
Table 6: Link Budget
Downlink
Value
Notes
Max Tx Power (dBm)
+30
Manually calculated (balanced) Node B Tx Pwr.
Max Rx Sensitivity (dBm)
-115
Specification based UE Rx level at 0.1% BLER.
145
Difference between Node B Tx and UE Rx Sens.
Max Tx Power (dBm)
+24
Max Tx Power for a Power Class 3 UE.
Max Rx Sensitivity (dBm)
-121
Specification based Node B Rx level at 0.1% BLER.
145
Difference between UE Tx and Node B Rx Sens
Max path loss (dB)
Uplink
Max path loss (dB)
Difference (dB)
0
Difference between UL and DL path losses
The only non-specified value is “Max Tx Power (dBm)” for the Downlink. This value was chosen
specifically because it balances the Uplink and Downlink path losses.
A complete Link Budget analysis would include variables such as LNA existence, various Radio Access
Bearers due to their difference in gain as a function of Spreading Factor (a description of Spreading
Factor is provided in the Measurement Fundamentals section), cable loss, Antenna and Macro Diversity
(a description of Macro Diversity is provided in the Mobility Management section), etc.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 16 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
4.3
Basic Design Requirements
This section describes fundamental design guidelines that are required for basic system operation. It is
strongly suggested that these basic requirements be satisfied before further optimization of the radio
network is pursued.
For example, if this were an FDMA/TDMA network such as GSM or IS-136, frequency planning would be
included in this section. However, since frequency reuse is not a primary consideration in WCDMA, it is
not included.
1.
Pilot Pollution
Since the basis of WCDMA is to allow for multiple access based upon code division instead of frequency
division, care must be taken to manage over-propagation of cells in the network. As mentioned later in
the Neighbor List Determination section, all cells that provide coverage in a given geographic area must
be neighbors; else they are seen as noise. An over-propagating cell would therefore need to have
neighbor relationships with all cells with which it overlaps. This of course would mean the overpropagating cell would be heavily utilized and would require a very large capacity.
Over-propagating cells also cause Call Establishment problems. Call Establishment has its own section
within this guide, but in short; a UE establishes calls on a single cell based upon its having the best
Common Pilot Channel (CPICH) signal level and/or quality. If a cell has propagated into an area where
there are no neighbors assigned from it to other closer cells in terms of distance to the mobile, the call will
drop. Even if there are neighbors assigned, the noise level will be increased for a short time until the
surrounding cells have been added to the call through the process of Soft Handover.
Fundamentally, Pilot Pollution is Common Pilot Channel (CPICH) power where it is not desired due the
over-propagation of cells. The current method used to reduce Pilot Pollution requires a drive test of the
area with a CPICH scanner. CPICH propagation is then analyzed graphically (maps) and statistically.
The criteria for Pilot Pollution is 4 or more Common Pilot Channels serving within 5 dB of each other in
the same geographic area. In most cases, power changes, down-tilts, azimuth changes or antenna
changes are required to reduce over-propagation.
2.
Neighbor List Determination
Neighbor relationships fall into 3 categories where UMTS and the interaction between UMTS and GSM
are concerned.
 Intra-UARFCN Neighbors. These neighbor relationships are assigned wherever there is coverage overlap
between cells having the same UARFCN. These neighbor relationships allow for Soft Handover. It is important to
assign neighbor relationships between overlapping cells in order to allow multiple cells covering the same
geographic area to collectively serve a given UE.
A cell covering an area, but not in the other server’s neighbor lists is seen as noise by the UE which
causes the UE compensate by requiring more power.
 Inter-UARFCN Neighbors. These neighbor relationships allow for Hard Handover between cells with different
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 17 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
UARFCNs. The neighboring UARFCNs can be in either the same band or in a different band. Neighbor
relationships should be assigned between all overlapping UARFCNs.
 Inter-RAT Neighbors. Inter-RAT neighbor relationships allow for Hard Handover and Cell Reselection between
UMTS and GSM. The UMTS coverage area in all AT&T markets is a subset of the GSM coverage. Inter-RAT
neighbors should only be defined from UMTS to GSM cells that support EGPRS (EDGE). This is done in order to
allow for the greatest throughput when the UE performs an Inter-RAT Cell Change from the 3G to the 2G network.
Idle Mode Cell Reselection neighbors should be defined xx Inter-RAT neighbors should also be assigned to allow
UEs to handover from UMTS to GSM where there are no suitable UMTS carriers (coverage holes) within the
UMTS polygon.
Important! – Neighbor relationships for speech must not be defined from GSM to UMTS in order to avoid
E911 calls handing back to UMTS before they are ended.
Ericsson further defines neighbor types based upon how they exist between different RNCs and
technologies (GSM vs. UMTS).
 UTRAN Relations. All intra-RNC neighbor definitions including Intra and Inter-UARFCN.
 External UTRAN Relations. All inter-RNC neighbor definitions including Intra and Inter-UARFCN.
 GSM Relations. All Inter-RAT neighbor definitions.
4.3.3 Scrambling Code Usage
Each cell in the network is assigned a Primary Scrambling Code. The primaryScramblingCode [Cell, 0
to 511, Integer, Variable] parameter is an integer value 0-511 inclusive. For the interest of this section, it
is important to avoid co-UARFCN co-Scrambling Code use in the same geographic area. However, if
there are more than 512 cells in use, Scrambling Codes must be reused very carefully. It is suggested
that reuses of Scrambling Code among the same UARFCN only exist where there is ample isolation.
Optionally, Scrambling Codes can also be divided into 64 groups of 8 codes each. Scrambling Code
planning would then be much like frequency planning with a reuse of 64. The advantage to this type of
planning could be a less complex code search procedure for the UE.
4.
Measurement Fundamentals
Before we get into Idle Mode, Call Establishment and Mobility Management, it is important to understand
the fundamental measurements used by the UE and RNS to make radio related decisions. These
measurements are commonly used when referencing signal level (RSCP) and signal quality (Ec/No). The
signal level (RSCP) and signal quality (Ec/No) of the Primary Common Pilot Channel (CPICH) define the
coverage area of the cell. SIR and BLER are also described as they are used to control uplink and
downlink power.
1.
PCPICH
The Primary Common Pilot Channel (CPICH) is one of the continuously transmitted downlink Physical
Channels. It is unique in that it is the reference used by the UE to make radio related decisions for Cell
Selection, Cell Reselection , Soft (intra-frequency) Handover and Hard (inter-frequency) Handover as well
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 18 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
as Inter-RAT Handover. All signal level and quality measurements are made based upon or relative to
the Primary Common Pilot Channel.
The power of Primary Common Pilot Channel is set to an absolute value per cell at the Reference Point
(antenna connector) through the primaryCpichPower [Cell, 300, 0.1dBm, Fixed] parameter. All other
downlink Physical Channels on the cell are set relative (dB) to the Primary Common Pilot Channel. Since
proper downlink power settings are necessary to allow the UE to enter Idle Mode, they are covered in
detail in the Idle Mode section.
4.4.2 PCPICH RSCP
The Primary Common Pilot Channel Received Signal Code Power, commonly called “RSCP”, is simply
the received power (dBm) of the Common Pilot Channel.
In order to really understand Received Signal Code Power (RSCP), it is important to understand the basic
concept of spreading and de-spreading. Spreading is the process of taking a signal, in this case the
Primary Common Pilot Channel (CPICH) signal, and transforming it into a signal that occupies a much
larger bandwidth. This is done in two steps. First, the original signal is binary multiplied by a Spreading
Code. The Spreading Code, also known as the Channelization Code or Orthogonal Variable Spreading
Factor (OVSF) Code is unique within the cell and when binary multiplied by Primary Common Pilot
Channel (CPICH) signal allows it to be isolated from the other spread signals within the cell.
The Primary Common Pilot Channel (CPICH) has a bit rate of 30kb/s. 2 bits = 1 symbol in the downlink.
The bits in the Spreading Code are referred to as “chips”. The number of chips per data symbol is called
the Spreading Factor. 3,840,000 chips / 15,000 symbols = 256. The Primary Common Pilot Channel
(CPICH) uses a Spreading Factor of 256. Seen yet another way, each Primary Common Pilot Channel
(CPICH) symbol is spread into 256 chips causing the spread signal to occupy 256 times the bandwidth of
the original signal.
Second, since the Spreading Codes are only unique within a cell, the signal must be further “scrambled” to
make it unique within the geographic coverage area. This is done by exclusively ORing the already spread
signal with a primaryScramblingCode [Cell, 0 to 511, Integer, Variable]. There are a total of 512 Primary
Scrambling Codes available, so co-UARFCN co-Primary Scrambling Code use might be necessary in
geographic areas with greater than 512 cells. See the Scrambling Code Selection section for cautions.
At the other end, receiving the symbols is simply a matter of first de-scrambling, then de-spreading the
signal using the same scrambling and spreading codes used to initially spread the symbols.
4.4.3 CPICH Ec/No (Ec/Io)
The Primary Common Pilot Channel (CPICH) received Energy per Chip (Ec) to Noise (No) ratio,
commonly referred to as Eee-Cee-N-Not, is used to measure the received quality of the Primary Common
Pilot Channel (CPICH). It is the ratio of the received Energy per Chip to the Noise power spectral density in
the band. In this case, the Chip Energy (Ec) is the power of the spread Primary Common Pilot Channel
(CPICH) at the receiver. Ec is equivalent to Received Signal Code Power (RSCP) in that both measure the
power of the Primary Common Pilot Channel (CPICH); the only difference being Ec is the power of
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 19 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
the spread signal whereas RSCP is the power measured after de-spreading. No (N-not) is the received
wide band power, including thermal noise and noise generated in the receiver within the receiver’s
bandwidth.
The term Ec/Io is also used to denote Primary Common Pilot Channel (CPICH) quality with the only
difference being the denominator where Io includes interference only. The use of the term Ec/Io is where
receivers are concerned is not technically accurate due mainly to the fact that receivers do not discern
Noise from Interference and as such, cannot accurately measure Ec/Io. However, Io is commonly used in
RF Design (propagation) tools when noise is not considered.
4.4.4 Eb/No
Eb/No, commonly referred to as Eee-Bee-N-Not or ebno, is the received energy per Bit (symbol) of the
signal over the received wide band power, including thermal noise and noise generated in the receiver,
within the receiver’s bandwidth. The fundamental difference between Eb/No and Ec/No is Spreading
Factor. Ec is of course the energy of the spread signal. By factoring in the Spreading Factor, we get the
energy of a bit or symbol over the received wide band power, including thermal noise and noise generated
in the receiver, within the receiver’s bandwidth. Eb/No therefore equals Ec/No * Spreading Factor.
Eb/No is commonly used when referencing Physical Channels that carry user data or signaling as
opposed to Physical Channels such as the Common Pilot Channel (CPICH) which only carries repetitive
data.
5.
SIR
SIR is the Signal to Interference Ratio. It is equivalent to (RSCP / ISCP) * Spreading Factor. RSCP is
defined above; ISCP is the Interference Signal Code Power which is essentially the interference from
other cells (DL) or UEs (UL) excluding noise. SIR is a quality metric used to maintain appropriate power
levels in the uplink and downlink. The UTRAN uses a very fast power control technique called “closedloop power control” where power is adjusted 1500 times per second in order to maintain the Signal to
Interference Ratio at a configured target value. SIR is further explained in the Mobility Management
section.
6.
RSSI
The Received Signal Strength Indication is a signal level measurement of the downlink which includes
thermal noise and noise generated in the receiver within the receiver’s bandwidth. Received Signal
Strength Indication (RSSI) is equivalent to the No measurement used in Ec/No above.
7.
RTWP
Received Total Wideband Power measured by the Node B is the received wide band power, including
thermal noise and noise generated in the receiver within the receiver’s bandwidth.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 20 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
4.4.8 BLER
BLER is the Block Error Rate at the Transport Channel Layer. CPICH RSCP, CPICH Ec/No, Eb/No and
SIR are all measurements of the Physical Layer. The Transport Channel layer resides above the Physical
Layer. At the Transport Layer, data from the Physical Layer is put into CRC encoded Blocks. If a Block
fails a CRC check, it is considered in error. BLER indicates the percentage of these Blocks in error.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 21 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5. Parameters Described Within Context
1.
Idle Mode
Idle Mode is a state every UE enters when it is powered on. It is also the state in which each powered on
UE spends most of its time. In this state, the UE must be ready and able to Originate and Terminate
calls. This section includes cell selection, but does not include Cell Reselection as Cell Reselection is a
function of mobility and as such is covered in the Mobility Management section.
1.
Cell Search Procedure
After either power up or entry into network coverage, the UE must begin to read information on the BCCH.
The Broadcast Control CHannel (BCCH) is used to broadcast System Information to all UEs within its
coverage area. This is accomplished in 3 steps. However, before the 3 steps are described, it is
important to understand the Slot and Frame structure of the downlink. A Slot is made up of 2560 Chips
(meaning it’s a spread signal). 15 Slots make up one 10 ms Frame. 73 Frames make up one
Superframe.
1. Slot Synchronization with the downlink is acquired by correlating the Primary Synchronization Code,
common to every cell and known by all UEs, with the Primary Synchronization Channel (P-SCH)
transmitted on the downlink. It is important to know that neither the Primary nor the Secondary
Synchronization Channel are ever Scrambled using the Primary Scrambling Code. Each cell serving
in the UE’s geographic area transmits a Primary Synchronization Channel (P-SCH). The cell that the
UE is able to obtain the strongest correlation with is chosen as the serving cell. The Primary
Synchronization Channel (P-SCH) power level is controlled by the primarySchPower [Cell, -18,
0.1dB, Fixed] parameter which is set relative to the power of the Primary Common Pilot Channel
(CPICH).
Figure 1: Slot and Frame Structure
720 ms
F0
F1
...
F2
F70
F71
...
Superframe = 72 frames
10 ms
S0
S1
S2
...
S13
S14
Frame = 15 Slots
.667 ms
...
Slot = 2560 Chips
The process in which UARFCNs are chosen for a Slot Synchronization attempt is UE implementation
dependant.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 22 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
2. Even though the UE has acquired Slot Synchronization, it still needs to know the Slot number within a
Frame (Frames have 15 Slots) so it can know where the Frame begins. It does this by correlating
one of the 16 Secondary Synchronization Codes with the Secondary Synchronization Channel (SSCH). It is important to know that neither the Primary nor the Secondary Synchronization Channel
are ever Scrambled using the Primary Scrambling Code. The 16 Secondary Synchronization Codes
are used to form 64 unique Secondary Synchronization Channel sequences. Once the UE has
decoded 15 successive Secondary Synchronization Codes, it not only knows where the Frame begins,
but the Code Group (used in step 3) as well. The UE is now Frame Synchronized. The Secondary
Synchronization Channel (S-SCH) power is controlled by the secondarySchPower [Cell,
-35, 0.1dB, Fixed] parameter which is set relative to the power of the Primary Common Pilot Channel
(CPICH).
3. Now that the UE is Slot and Frame Synchronized, it must still determine the cell’s Primary Scrambling
Code before it can begin to read the Broadcast Control CHannel (BCCH). In step 2, the UE discovers
the cell’s Code Group. Each Code Group identifies 8 possible Primary Scrambling Codes. The
correct Primary Scrambling Code is determined by correlating each of the 8 possibilities with the
Common Pilot Channel (CPICH). Once the correct Primary Scrambling Code has been found, the UE
can detect the Primary Common Control Physical Channel (P-CCPCH) which carries the Broadcast
CHannel (BCH) Transport Channel. The Broadcast CHannel (BCH) transmission power is controlled
throughput bchPower [Cell, -31, 0.1dB, Fixed] which is set relative to the power of the Primary
Common Pilot Channel (CPICH). The Broadcast CHannel (BCH) carries the Broadcast Control
CHannel (BCCH) Logical Channel. The cell’s Primary Scrambling Code is configured using the
primaryScramblingCode [Cell, 0 to 511, Integer, Variable] parameter.
The Primary Common Control Physical Channel (P-CPPCH) carries the System Frame Number (SFN)
which is used as the timing reference for all Physical Channels. The System Frame Number (SFN)
ranges from 0 to 4095 (inclusive). For more information about Slot and Frame synchronization, see [3e].
2.
PLMN Selection
Now the UE is able to read the Broadcast Control CHannel (BCCH). If the UE finds its subscribed Public
Land Mobile Network (PLMN) it then continues to read System Information from the BCCH.
1.
Information on the Broadcast Control CHannel (BCCH)
The Broadcast Control Channel (BCCH) broadcasts information consisting of a Master Information Block
(MIB), up to 18 System Information Blocks (SIB) types numbered 1-18, and up to 2 Scheduling Blocks
(SB). Ericsson has implemented a Master Information Block (MIB) and System Information Blocks (SIB)
types 1, 3, 5, 7, 11 and 12.
The following breakdown of the Master Information Block (MIB) and System Information Blocks (SIBs)
provides an indication of where the UE gets the information necessary in order to maintain Idle Mode,
Establish Calls, and Manage Mobility. The “Layer 3 Message” column was derived from TEMS 6.0 log
files. The Purpose column provides a brief description of where the parameter applies.
 Master Information Block (MIB). The Master Information Block (MIB) is sent at a fixed rate of every 8 Frames
(80ms). It contains information that identifies the network as well as the start position and interval of each of the
System Information Blocks (SIBs). The Master Information Block (MIB) also contains a Value Tag associated with
each System Information Block supported. If the Value Tag for any supported System Information Block changes,
the UE must read that System Information Block (SIB). In order to avoid the UE having to read each and every
Master Information Block (MIB), a Paging Type 1 message is sent and repeated noOfMibValueTagRetrans [RNC,
0, Retransmissions, Fixed] times to all UEs indicating a Value Tag has changed in the Master Information Block
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 23 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
(MIB).
Table 7: Master Information Block (MIB) Contents
Ericsson Parameter
Purpose
Layer 3
Message
mcc
MCC :
The Mobile Country Code
mnc
MNC :
The Mobile Network Code
sib1StartPos
Repx : y
Sets the start position of SIB 1 where x equals the
repetition period and y equals the SFN / 2.
sib1RepPeriod
sib-Pos : repx
Sets the SIB 1 repetition period where x equals a
number of Frames.
sib3StartPos
Repx : y
Sets the start position of SIB 3 where x equals the
repetition period and y equals the SFN / 2.
sib3RepPeriod
sib-Pos : repx
Sets the SIB 3 repetition period where x equals a
number of Frames.
sib5StartPos
Repx : y
Sets the start position of SIB 5 where x equals the
repetition period and y equals the SFN / 2.
sib5RepPeriod
sib-Pos : repx
Sets the SIB 5 repetition period where x equals a
number of Frames.
sib7StartPos
Repx : y
Sets the start position of SIB 7 where x equals the
repetition period and y equals the SFN / 2.
sib7RepPeriod
sib-Pos : repx
Sets the SIB 7 repetition period where x equals a
number of Frames.
sib11StartPos
Repx : y
Sets the start position of SIB 11 where x equals the
repetition period and y equals the SFN / 2.
sib11RepPeriod
sib-Pos : repx
Sets the SIB 11 repetition period where x equals a
number of Frames.
sib12StartPos
Repx : y
Sets the start position of SIB 12 where x equals the
repetition period and y equals the SFN / 2.
sib12RepPeriod
sib-Pos : repx
Sets the SIB 12 repetition period where x equals a
number of Frames.
 System Information Block 1 (SIB 1). System Information Block 1 (SIB 1) contains Location Area (LA), Routing
Area (RA) information and timer parameters. Since this System Information Block contains the Location Area (LA)
and Routing Area (RA) information, it must also be read when a LA or RA border is crossed. The parameter
sib1PLMNScopeValueTag [Cell, 0 to 31, Integer, Variable] controls when System Information Block 1 (SIB 1) is
read and must be set so that neighboring Location Areas and Routing Areas have different values.
Table 8: System Information Block 1 (SIB 1) Contents
Ericsson Parameter
Layer 3 Message
Purpose
lAC
LAC : xxxxx
Location Area Code used by CS Core Network
t3212
CS domain – T3212 : x
Periodic Location Area Update interval in deci-minutes,
e.g. 1 = 6 minutes.
att
CS domain – ATT : x
Indicates if the UE is allowed to IMSI Attach to the CS
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 24 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Ericsson Parameter
Layer 3 Message
Purpose
Core Network
cnDrxCycleLengthCs
CS domain – DRXCycleLengthCoeff : k
Discontinuous Reception (DRX) Cycle Length
Coefficient.
rAC
RAC : xx
Routing Area Code used by PS Core Network
nmo
NMO : x
Network Mode of Operation
cnDrxCycleLengthPs
PS domain – DRXCycleLengthCoeff : k
Discontinuous Reception (DRX) Cycle Length
Coefficient.
 System Information Block 3 (SIB 3). System Information Block 3 (SIB 3) contains parameters for cell selection
and reselection.
Table 9: System Information Block 3 (SIB 3)
Ericsson Parameter
Layer 3 Message
Purpose
qualMeasQuantity
cellSelectQualityMeasur
e:x
Determines if cell ranking uses quality measurements.
sRatSearch
s-SearchRAT : x
Used to determine when Inter-RAT measurements
begin.
sHcsRat
s-HCS-RAT : x
Used to determine when Inter-RAT measurements
begin.
qQualMin
q-QualMin : x
Used in Cell Selection and Re-selection
qRxLevMin
q-RxlevMin : x
Used in Cell Selection and Re-selection
qHyst2
q-Hyst-I-S : x
Used in Cell Selection and Re-selection
treSelection
t-Reselection-S : x
Used in Cell Selection and Re-selection
maxTxPowerUl
maxAllowedUL-TXPower : x
Max UE power allowed on the uplink.
cellReserved
CellReservedForOperat
orUse : x
Indicates if the cell is reserved by the operator.
 System Information Block 5 (SIB 5). System Information Block 5 (SIB 5) contains parameters that determine the
configuration of Common Physical Channels (PhyCHs) in the cell.
Table 10: System Information Block 5 (SIB 5)
Ericsson Parameter
Layer 3 Message
Purpose
pichPower
pich-PowerOffset : x
Power level of the Page Indication CHannel (PICH)
relative to the Primary Common Pilot Channel (CPICH)
power
aichPower
Aich-PowerOffset : x
Power level of the Acquisition Indication CHannel
(AICH) relative to the Primary Common Pilot Channel
(CPICH) power
primaryCpichPower
primaryCPICH-TXPower : x
Power level of the Primary CPICH
ConstantValueCprach
constantValue : x
Used by the UE to calculate initial power on the
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 25 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Ericsson Parameter
Layer 3 Message
Purpose
PRACH.
powerOffsetP0
powerRampStep : x
Preamble power step when no Acquisition Indicator is
received.
preambleRetransMax
preambleRetransMax :
x
Maximum number of Preambles sent in one ramping
cycle
 System Information Block 7 (SIB 7). System Information Block 7 (SIB 7) contains uplink interference value.
Due to the fact that this value changes very often, this System Information Block’s interval is controlled by a timer.
When the UE receives System Information Block 7 (SIB 7), a timer is started. Once the timer expires, the
information is considered invalid and the UE reads the information again. The expiration time is the value of the
sib7RepPeriod [RNC, 16, Frames, Fixed] parameter multiplied by the sib7expirationTimeFactor [RNC, 1,
Factor, Fixed] parameter.
Table 11: System Information Block 7 (SIB 7)
Ericsson Parameter
n/a
Layer 3 Message
ul-Interference
Purpose
Provides uplink Received Total Wideband Power
(RTWP). RTWP = No
 System Information Block 11 (SIB 11). System Information Block 11 (SIB 11) contains the cell’s soft/softer
handover neighbor list including the Primary Scrambling Code of each neighbor. This handover list is supplied to
the UE before a call is established so that the UE may make Intra-frequency measurements before receiving the
MEASUREMENT CONTROL message from the Serving Radio Network Controller (SRNC).
Table 12: System Information Block 11 (SIB 11)
Ericsson Parameter
Layer 3 Message
Purpose
reportingRange1a
e1a – reportingRange :
x
CPICH reporting range add threshold.
hysteresis1a
e1a – hysteresis : x
Hysteresis used for CPICH add threshold.
timeToTrigger1a
e1a – timeToTrigger : x
Time between CPICH add and reporting.
reportingRange1b
e1b – reportingRange :
x
CPICH reporting range drop threshold.
hysteresis1b
e1b – hysteresis : x
Hysteresis used for CPICH drop threshold.
timeToTrigger1b
e1b – timeToTrigger : x
Time between CPICH drop and reporting.
hysteresis1c
e1c – hysteresis : 2
Hysteresis used for CPICH replacement.
timeToTrigger1c
e1c – timeToTrigger : x
Time between CPICH replacement and reporting.
hysteresis1d
e1d – hysteresis : x
Hysteresis used in best CPICH replacement.
timeToTrigger1d
e1d – timeToTrigger : x
Time between best CPICH replacement and reporting.
 System Information Block 12 (SIB 12). System Information Block 12 (SIB 12) contains measurement control
information to be used in the cell.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 26 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Table 13: System Information Block 12 (SIB 12)
Ericsson Parameter
n/a
Layer 3 Message
Purpose
There are no configurable parameters reported in this
SIB
n/a
The UE reads System Information only when one of the following events occurs:
 The UE is powered up.
 Immediately after Cell Reselection (except SIB 1 where the parameter sib1PLMNScopeValueTag [Cell, 0 to 31,
Integer, Variable] is used).
 The UE receives a Paging Type 1 message indicating System Information has changed. Then the MIB is read
which indicates the SIBs that have been updated.
 The timer expires for SIBs with an expiration timer (SIB 7 only).
Otherwise, in order to conserve battery life, the UE does not read the System Information. This is
something to consider when observing Layer 3 messages using a diagnostic UE.
5.1.2.2
Camping on a Suitable Cell
Now that the UE has read the Broadcast Control CHannel (BCCH), it knows the values of the parameters
that help the UE determine if the cell is suitable. The Cell must not be Reserved and it must be suitable in
terms of signal level (Srxlev) and quality (Squal).
cellReserved [Cell, NOT_RESERVED, String, Variable] is a cell based parameter sent in System
Information Block 3 (SIB3). It has two possible settings; RESERVED and NOT_RESERVED. When set
to RESERVED, only UEs with SIMs having an ACC of 11 or 15 (set in the SIM’s HLR profile) will be
allowed to camp on the cell assuming the cell is on their home PLMN. See TS 25.306 for details. All
other UEs (with SIMs having other than ACC 11 or 15) will avoid camping on the cell. The UE’s Cell
Reselection process will also avoid reserved cells.
accessClassNbarred [Cell, 0, Integer, Fixed] is another cell based parameter sent in System Information
Block 3 (SIB3). It makes it possible to disallow UEs with SIM that have specific Access Classes
provisioned for them in the HLR from accessing the network. This parameter differs from the
cellReserved [Cell, NOT_RESERVED, String, Variable] parameter in that accessClassNbarred [Cell, 0,
Integer, Fixed] still allows the UE to camp on the network. This could cause a worst case senerio wherein
the UE camps on the 3G network, but is not allowed to register.
The signal level (Srxlev) and quality (Squal) parameters are commonly referred to as the “S” parameters.
Srxlev = Qrxlevmeas – qRxLevMin [Cell, -115, dBm, Fixed] – Pcompensation
Where:
 Srxlev is the signal level criteria used to determine a cell’s suitability.
 Qrxlevmeas is the Primary Common Pilot Channel Received Signal Code Power (PCPICH RSCP) as measured by
the UE.
 qRxLevMin [Cell, -115, dBm, Fixed] is sent in System Information Block 3 (SIB 3) for the serving cell which
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 27 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
indicates the minimum acceptable Primary Common Pilot Channel Received Signal Code Power (PCPICH RSCP).
 The quantity called Pcompensation is the maximum value of maxTxPowerUl [Cell, 24, dBm, Fixed] – P or 0 where
maxTxPowerUl [Cell, 24, dBm, Fixed] is sent in System Information Block 3 (SIB 3) which indicates the maximum
transmission power allowed for a UE and P is the output power of the UE according to its Power Class.
Example part 1 of 3. A Power Class 3 UE is served at a path loss 10 dB less than the maximum path loss
as indicated in the Link Budget table, qRxLevMin [Cell, -115, dBm, Fixed] is set conservatively at -115
dBm, and maxTxPowerUl [Cell, 24, dBm, Fixed] is set at 24 dBm. Pcompensation is the maximum value
of either 24 dBm – 24 dBm or 0. So Srxlev = -105 dBm minus -115 dBm minus 0. Srxlev = 10.
Squal = Qqualmeas – qQualMin [Cell, -19, dB, Fixed]
Where:
 Qqualmeas is the Primary Common Pilot Channel Chip Energy over Noise Spectral Density (PCPICH Ec/No) as
measured by the UE.
 qQualMin [Cell, -19, dB, Fixed] is sent in System Information Block 3 (SIB 3) for the serving cell indicates the
minimum acceptable Primary Common Pilot Channel Chip Energy over Noise Spectral Density (PCPICH Ec/No)
for the cell.
Example part 2 of 3. The UE is served at an Ec/No of -14 dB and qQualMin [Cell, -19, dB, Fixed] is set
at -19 dB. -14 dB minus -19 dB. Squal = 5 dB.
The cell is considered suitable if its cell selection criterion (S criterion) is met. In order for the S criterion
to be met, Srxlev and Squal must have positive values.
Example part 3 of 3. The UE calculates both S criteria with positive resulting values. The cell is
considered acceptable where the S criterion is concerned. It is now allowed to transmit on the uplink.
3.
IMSI and GPRS Attach
Assuming now that the UE has found its home PLMN and is Camping on a suitable cell, it must
International Mobile Subscriber Identity (IMSI) Attach and General Packet Radio Service (GPRS) Attach
to the Circuit Switched (CS) and Packet Switched (PS) Core Networks (CN) respectively. This process is
also known as Registration.
1.
Attach Procedure
If att [LA, 1=TRUE, Integer, Fixed] sent in System Information Block 1 (SIB 1) is set to 1, the UE must
establish a Signaling Connection to notify the Circuit Switched Core Network (CS-CN) and Packet
Switched Core Network (PS-CN) that it is powered on and within network coverage. Signaling
Connections are always initiated by the UE. First, the UE must access the Node B in order to send a
request to the RNC to establish a Radio Resource Control (RRC) Connection. This is done through the
Physical Random Access Channel (PRACH) on the uplink and the Acquisition Indicator Channel (AICH)
on the downlink. The UE sends successive attempts on the uplink, each at a greater power level until the
Node B responds on the Acquisition Indicator CHannel (AICH) on the downlink. The Acquisition Indicator
CHannel (AICH) power is set relative to the Primary Common Pilot CHannel (PCPICH) through
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 28 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
aichPower [Cell, -6, dB, Fixed]. The process of sending successive attempts, each at an increased
power level, is known as Preamble Ramping. The initial power on the PRACH is determined by the UE
using the following formula:
P_PRACH = L_PCPICH + RTWP + ConstantValueCprach [Cell, -27, dB, Fixed]
 P_PRACH is the power used for the initial PRACH attempt.
 L_PCPICH is the path loss estimated by the UE (difference between primaryCpichPower [Cell, 300, 0.1dBm,
Fixed] as indicated in SIB 5 and PCPICH RSCP as measured by the UE).
 RTWP is the Received Total Wideband Power measured by the Node B as indicated in SIB 7.
 ConstantValueCprach [Cell, -27, dB, Fixed] determines the level below the Received Total Wideband Power at
which Preamble Ramping begins.
For example, a UE is served at a path loss 10 dB less than the maximum path loss as indicated in the Link
Budget table, so L_PCPICH = 132 dB. Let’s also say the RTWP = -105 dBm and ConstantValueCprach
[Cell, -27, dB, Fixed] = -27 dB. The sum of these values, or P_PRACH, is 0 dBm. The UE will begin the
attempt at 0 dBm.
Subsequent transmission attempts within a Ramping Cycle are made at an increased power level relative
to the former attempt. The increase in power level between steps is controlled by the parameter
powerOffsetP0 [Cell, 2, dB, Fixed] which the UE reads from System Information Block (SIB) 5.
The UE ceases its access attempt as soon as it receives an Acknowledgement Indicator (AI) on the
downlink Acquisition Indication CHannel (AICH). However, the UE is not allowed to ramp its power
indefinitely. The preambleRetransMax [Cell, 15, Preambles, Fixed] parameter in SIB 5 controls how
many successive Preambles the UE can transmit within one Ramping Cycle and the maxPreambleCycle
[Cell, 3, Cycles, Fixed] parameter controls how many Ramping Cycles can be attempted before the UE
aborts the access attempt.
Figure 2: Power Ramping on RACH
powerOffsetP0
AI
powerOffsetPpm
P_PRACH
Power
(dB)
Message Part
RACH
preambleRetransMax
(Ramping Cycle)
AICH
Time
As soon as the UTRAN responds with an Acknowledgement Indicator (AI) on the downlink, the UE sends
the PRACH Message Part informing the Radio Network Controller (RNC) that it wishes to set up a Radio
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 29 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Resource Control (RRC) Connection. The power at which PRACH Message Part is sent is equal to the
sum of the power of the successful transmission attempt and powerOffsetPpm [Cell, 0, dB, Fixed].
Once the UE and Radio Network Controller (RNC) have established a Radio Resource Control (RRC)
Connection, the RNC establishes an Iu Control Plane connection over the Iu interface to the appropriate
Core Network (CN) element(s), i.e. the SGSN, MSC or both. The resulting Transparent Message Transfer
connection between the UE and Core Network (CN) element(s) allows the exchange of Non- Access
Stratum (NAS) messages such as Registrations, Location or Routing Area Updates, and Service
Requests for User Plane connections. The figure below details all of the steps necessary to complete a
Radio Resource Control (RRC) Connection. Following the figure are detailed explanations for each step.
Figure 3: RRC Connection Signaling Flow
Uu
UE
1
RRC
Iub
Node B
RRC Connection Request
RACH Message Part
2
3
4
5
10
RRC
NBAP
RRC
Initiate UE Context
Activated Algorithms:
- Power Control
- Iub and Uu Timing Scheduling
- Admission Control
Radio Link Setup Request
NBAP
Resource Allocation
6
8
RNC
NBAP
Radio Link Setup Response
NBAP
7
AAL2 Connection Setup for DCH
Start Receive of UL DPCH
Start Radio Link Supervision
Suspend SRB3, SRB4 and
9
other RLC AM entities
RRC Connection Setup
FACH
RRC
11
Transport Bearer Synchronization
Start Transmission of
12
DL DPCH
13
L1 Synchronization
14 NBAP
15
RRC
DCH
Radio Link Restore Indication
RRC Connection Complete
16
NBAP
RRC
Resume SRB3, SRB4 and
other RLC AM entities
1. RRC Connection Request. After the UE receives the Acknowledgement Indicator (AI) on the
downlink, it initiates the establishment of a Radio Resource Control (RRC) connection by sending the
Radio Resource Control (RRC) Connection Request message with an establishment cause of
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 30 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
“Registration” within the Message Part using the Random Access Channel (RACH) Transport
Channel.
2. Initiate UE Context. The Radio Resource Control (RRC) Connection attempt is assigned a UTRAN
Radio Network Temporary Identity (U-RNTI) which is unique within the network.
3. Activated Algorithms. At this point, the Power Control algorithm sets the initial downlink and uplink
Dedicated Physical Data CHannel (DPDCH) and Dedicated Physical Control CHannel (DPCCH)
transmission power. These channels are time multiplexed on the downlink and code (I/Q) multiplexed
on the uplink. Together they are typically referred to as a Dedicated Physical CHannel (DPCH). The
following initial power level parameters are used whenever a Radio Link is set up.
The initial downlink Dedicated Physical Data CHannel (DPDCH) power is determined using the following
formula:
P_DL_DPDCH = primaryCpichPower [Cell, 300, 0.1dBm, Fixed] + (dlInitSirTarget [RNC, 41,
0.1dB, Fixed] - Ec/No_PCPICH) + cBackOff [RNC, 0, 0.25dB, Fixed] + 10 log(2/SF_DL_DPDCH)
Where:
 P_DL_DPDCH is the initial downlink Dedicated Physical Data CHannel (DPDCH) power.
 primaryCpichPower [Cell, 300, 0.1dBm, Fixed] sets the power of the Primary Common Pilot Channel (P-CPICH)
sent in SIB 5.
 dlInitSirTarget [RNC, 41, 0.1dB, Fixed] sets the required initial Signal to Interference Ratio (SIR) Target.
 Ec/No_PCPICH is the ratio of Chip Energy to the Noise Power Spectral Density of the Primary Common Pilot
CHannel (P-CPICH) as measured by the UE. If this measurement is not available, ecNoPcpichDefault [RNC, 16, dB, Fixed] is used.
 cBackOff [RNC, 0, 0.25dB, Fixed] is used to offset the value of P_DL_DPDCH.
 SF_DL_DPDCH is the Spreading Factor of the downlink Dedicated Physical Data CHannel (DPDCH).
The initial downlink Dedicated Physical Control CHannel (DPCCH) power is set relative to the initial
downlink Dedicated Physical Data Channel (DPDCH) power by means of a series of offsets:
P_DL_DPCCH_TFCI = (P_DL_DPDCH + pO1 [RNC, 0, 0.25dB, Fixed] )
P_DL_DPCCH_TPC = (P_DL_DPDCH + pO2 [RNC, 12, 0.25dB, Fixed] )
P_DL_DPCCH_PILOT = (P_DL_DPDCH + pO3 [RNC, 12, 0.25dB, Fixed] )
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 31 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 4: Downlink DPCCH Power
D L Power
(dB)
pO2
pO1
pO3
TPC
TFCI
Pilot
Data 1
Data 2
Time
DPDCH
DPCCH
DPDCH
DPCCH
1 Timeslot (10ms)
Where:
 P_DL_DPCCH_TFCI is the initial power of the Dedicated Physical Control CHannel Transport Format Combination
Indicator (DPCCH TFCI) field.
 pO1 [RNC, 0, 0.25dB, Fixed] sets the offset between the Data field and the Dedicated Physical Control CHannel
Transport Format Combination Indicator (DPCCH TFCI) field.
 P_DL_DPCCH_TPC is the initial power of the Dedicated Physical Control CHannel Transmit Power Control
(DPCCH TPC) field.
 pO2 [RNC, 12, 0.25dB, Fixed] sets the offset between the Data field and the Dedicated Physical Control CHannel
Transmit Power Control (DPCCH TPC) field.
 P_DL_DPCCH_PILOT is the initial power of the Dedicated Physical Control CHannel Pilot field.
 pO3 [RNC, 12, 0.25dB, Fixed] sets the offset between the Data field and the Dedicated Physical Control CHannel
Pilot field.
The initial uplink Dedicated Physical Control CHannel (DPCCH) power is determined using the following
formula:
Power_UL_DPCCH_INIT = DPCCH_POWER_OFFSET - RSCP_PCPICH
Where:
 Power_UL_DPCCH_INIT is the initial uplink Dedicated Physical Control CHannel (DPCCH) power.
 DPCCH_POWER_OFFSET is calculated in the Radio Network Controller (RNC) and sent to the UE according to
the following formula:
DPCCH_POWER_OFFSET = primaryCpichPower [Cell, 300, 0.1dBm, Fixed] + RTWP + ulInitSirTarget - 10 log
(SF_DPCCH) + cPO [RNC, 0, 0.1dB, Fixed]
Where:
 DPCCH_POWER_OFFSET is an offset applied to Power_UL_DPCCH_INIT.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 32 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
primaryCpichPower [Cell, 300, 0.1dBm, Fixed] sets the power of the Primary Common Pilot CHannel (PCPICH). If the Radio Network Controller (RNC) does now know the Primary Common Pilot CHannel (P-CPICH)
power, as is the case when the UE is served by a Drift Radio Network Controller (DRNC), pcpichPowerDefault
[RNC, 33, dBm, Fixed] is used instead.
 RTWP is the Received Total Wideband Power level on the uplink measured by the Node B.
ulInitSirTarget is one of the following configurable parameters based upon the Spreading Factor of the Radio
Bearer.

ulInitSirTargetSrb [RNC, 57, 0.1dB, Fixed] for stand-alone Signaling Radio Bearers (SRB).

ulInitSirTargetLow [RNC, 49, 0.1dB, Fixed] for Radio Access Bearers (RABs) having minimum Dedicated
Physical Data CHannel Spreading Factors (DPDCH SF) equal to or higher than 32.

ulInitSirTargetHigh [RNC, 82, 0.1dB, Fixed] for RABs having minimum Dedicated Physical Data CHannel
Spreading Factors (DPDCH SF) equal to 16 or 8.

ulInitSirTargetExtraHigh [RNC, 92, 0.1dB, Fixed] for Radio Access Bearers (RABs) having minimum
Dedicated Physical Data CHannel Spreading Factors (DPDCH SF) equal to or lower than 4.
 SF_DPCCH is the Spreading Factor (SF) for the Dedicated Physical Control CHannel.
cPO [RNC, 0, 0.1dB, Fixed] is used to offset the initial uplink Dedicated Physical Data CHannel (DPDCH)
power.
 RSCP_PCPICH is the Received Signal Code Power (RSCP) of the Primary Common Pilot Channel (P-CPICH).
The initial uplink Dedicated Physical Data CHannel (DPDCH) power is determined according to the
relative power offset between the Dedicated Physical Control CHannel (DPCCH) and Dedicated Physical
Data Channel (DPDCH) as described in 3GPP TS 25.214. The UTRAN determines and signals the gain
factor to the UE for the reference Transport Format Combination (TFC) only. The UE then computes the
gain factors for other Transport Format Combinations (TFCs) based on the value for the reference
Transport Format Combination (TFC).
In addition to uplink and downlink power control, the Iub and Uu Timing Scheduling algorithms calculate
channel timing parameters. The Admission Control algorithm checks if the new radio link can be allowed
in the cell. The Code Control algorithms allocate the uplink scrambling code, downlink scrambling code,
and downlink channelization code.
4. Radio Link Setup Request. The RNC orders the Node B to reserve the necessary resources for a
new Node B communication context.
5. Resource Allocation. The Node B reserves the necessary resources for a new communication
context and calculates link characteristic parameters from the received uplink and downlink Transport
Format Combination Indicator (TFCI) or Transport Format Set (TFS) information.
6. Radio Link Setup Response. The Node B indicates to the RNC that the necessary resources are
allocated for the radio link. It includes the binding identifier and transport layer address for the AAL2
connection.
7. AAL2 Connection Setup for DCH. The transport bearer (AAL2 connection) needed for signaling is
set up over the Iub by the RNC.
8. Start Receive of UL DPCH – Start Radio Synchronization. The Radio Link Set Supervision
algorithm in the Node B starts evaluating the synchronization status of the Radio Link Set (RLS).
9. Suspend SRB3, SRB4, and other RLC AM entities. Signaling Radio Bearer 3 (SRB 3), Signaling
Radio Bearer 4 (SRB 4), and other Radio Link Control Acknowledged Mode (RLC AM) entities are
suspended.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 33 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
10. RRC Connection Setup. The RNC indicates the UE state shall be CELL_DCH. The message is
sent in Unacknowledged mode on the Forward Access CHannel (FACH).
11. Transport Bearer Synchronization. Transport Bearer Synchronization is achieved in the downlink
between RNC and Node B for each Dedicated CHannel (DCH).
12. Start Transmission of DL DPCH. The Node B only starts transmitting on the new radio link when
the downlink user plane (Dedicated Physical Data CHannel – DPDCH) is considered synchronized.
13. L1 Synchronization. Layer 1 synchronization is achieved between UE and Node B.
14. Radio Link Restore Indication. The Node B notifies the RNC that it has achieved uplink Layer 1
synchronization with the UE.
15. RRC Connection Complete. The UE starts the uplink transmission only after the reception of
downlink Dedicated Physical Channel (DPCH). The UE capabilities requested in step 10 are included
in this message. This information is used by the Radio Access Bearer (RAB) establishment
procedure, UE Security Handling, and the Channel Switching function. Radio Resource Control (RRC)
messages can now be sent in acknowledged mode on a Dedicated CHannel (DCH).
16. Resume SRB3, SRB4, and other RLC AM entities. The SRB3, SRB4, and other Radio Link
Control Acknowledged Mode (RLC AM) entities are resumed.
Through this dedicated connection, the UE is able to Register with the appropriate Core Network (CN)
Element(s).
4.
Location and Routing Area Updates
Location and Routing Area Updates, also known as Registration updates, must be performed in order to
provide the SGSN and MSC with an awareness of where the UE is located. Given the UE’s location, the
Core Network (CN) element can page the UE to deliver calls. This awareness helps to avoid
unnecessary paging when the UE is either turned off or is outside of the coverage area. Location Areas
are defined through the lAC [LA, N/A, Integer, Variable] broadcast on the Broadcast Control CHannel
(BCCH) in System Information Block 1 (SIB 1). Routing Areas are defined through the rAC [RNC, N/A,
Integer, Variable] also broadcast on the Broadcast Control CHannel (BCCH) in System Information Block
1 (SIB 1). Besides IMSI and GPRS Attaches, there are basically two different types of Registration
update; Normal and Periodic.
1.
Normal Update
A Normal Location or Routing Area update is performed when the UE either leaves Connected Mode, or
performs a Cell Reselection in Idle Mode to a cell within a different Location or Routing Area.
2.
Periodic Update
In addition to Normal Updates, Periodic Updates are performed. These updates are preformed
regardless of whether the UE is in Idle Mode or Connected Mode (CELL_DCH).
 Circuit Switched Core Network. The interval at which the UE periodically updates the Circuit Switched Core
Network (CS-CN) is set using the configurable t3212 [LA, 10, 6minutes, Fixed] parameter sent on the Broadcast
Control CHannel (BCCH) in System Information Block 1 (SIB 1).
 Packet Switched Core Network. The interval at which the UE periodically updates the Packet Switched Core
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 34 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Network (PS-CN) is set using the t3312 timer. This timer is set in the SGSN and sent to the UE via both the Attach
and the Routing Area Update messages.
The following table provides parameter ranges and default values involved in getting the UE into Idle
Mode. They are listed in the same order they were presented. The Level column indicates the network
element that owns the parameter. The class column indicates if the parameter is set based on Policy
(must be set this way), Fixed (recommended to be set this way) and Variable (set at your discretion).
2.
Call Establishment
Given the UE has successfully entered Idle Mode; it must then be able to originate and terminate calls
within acceptable Accessibility measures. This section considers all of the algorithms invoked during the
process of establishing a call.
1.
Radio Access Bearer
A Radio Access Bearer (RAB) is a connection between the UE and the Mobile Switching Center (MSC) in
the case of a Circuit Switched (CS) connection or between the UE and Serving GPRS Support Node
(SGSN) in the case of a Packet Switched connection. There is also the possibility of the UE connecting to
both the MSC and the SGSN as is the case in both SP0 and SP64. The Radio Access Bearer is set up
according to the Requested Service after the Signaling Connection is established through a Signaling
Radio Bearer. In the case of UE initiated connections where a Radio Access Bearer does not already
exist, the Requested Service is sent in the Random Access CHannel (RACH) Message Part. Although
the Requested Service could be sent by the UE, all Radio Access Bearers are actually initiated by the Core
Network (CN).
The variables within Quality of Service (QoS) fall into three main categories based upon the user’s need
for guaranteed throughput and/or latency. The three categories are Conversational; which provides
guaranteed low latency and throughput, Streaming; which provides guaranteed throughput but no
guarantee for latency, and Interactive (also referred to as Background) which provides guarantees for
neither throughput nor latency.
Another variable determines which side of the Core Network is used. In general, all Packet Switched
Radio Access Bearers are connected to the SGSN and all Circuit Switched Radio Access Bearers are
connected to the MSC.
The following types of Radio Access Bearers (RABs) are supported by the Ericsson UTRAN.
 Conversational Circuit Switched Speech AMR 12.2kb. This is the typical Speech Radio Access Bearer. Given
its Conversational Quality of Service (QoS) class, low latency and constant throughput are guaranteed. The
Conversational class of service is Transparent, meaning that in order to keep latency as low as possible, there is
no Transport layer Block retransmission service offered.
 Conversational Circuit Switched Speech AMR 12.2kb plus Interactive Packet Switched 64/64. This type of
Radio Access Bearer supports concurrent Circuit Switched Speech and Packet Switched Data. The Interactive
Quality of Service (QoS) class Data connection can support a data rate of 64kb in the Uplink and 64kb in the
downlink. Neither latency nor throughput is guaranteed for the Packet Switched connection. Ericsson refers to
this type of Radio Access Bearer (RAB) as SP64.
 Conversational Circuit Switched Speech AMR 12.2kb plus Interactive Packet Switched 64/HS. This type of
Radio Access Bearer supports concurrent Circuit Switched Speech and Packet Switched Data. The Interactive
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 35 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Quality of Service (QoS) class Data connection can support a data rate of 64kb in the Uplink and HSDPA for the
downlink. Neither latency nor throughput is guaranteed for the Packet Switched connection.
 Conversational Circuit Switched Speech AMR 12.2kb plus Interactive Packet Switched 384/HS. This type of
Radio Access Bearer supports concurrent Circuit Switched Speech and Packet Switched Data. The Interactive
Quality of Service (QoS) class Data connection can support a data rate of 384kb in the Uplink and HSDPA for the
downlink. Neither latency nor throughput is guaranteed for the Packet Switched connection.
 Conversational Circuit Switched Speech AMR 12.2kb plus Interactive Packet Switched 0/0. This Radio
Access Bearer (RAB) offers both Speech and a 0 bit rate Packet Switched connection. The 0 bit rate Packet
Switched connection is used as a “stepping stone” between 64/64 and Idle Mode. The result is a reduction in
latency from the end user’s perspective when using interactive applications such as Web Browsing. Ericsson
refers to this type of Radio Access Bearer (RAB) as SP0. The availability of this Radio Access Bearer (RAB) is
controlled through multiRabSp0Available [RNC, 1=TRUE, Binary, Fixed].
 Conversational Circuit Switched Data 64. This Radio Access Bearer (RAB) provides a Conversational class
64kb/s Unrestricted Digital Information (UDI) connection between the UE and the Circuit Switched Core Network.
The Conversational class of service is Transparent, meaning that in order to keep latency as low as possible, there
is no Transport layer Block retransmission service offered.
 Conversational Circuit Switched Data 64 plus Interactive Packet Switched 8/8. This Radio Access Bearer
(RAB) provides a Conversational class 64kb/s Unrestricted Digital Information (UDI) connection between the UE
and the Circuit Switched Core Network plus an Interactive class 8kb uplink, 8kb downlink Packet Switched
connection between the UE and Packet Switched Core Network. Ericsson refers to this type of Radio Access
Bearer (RAB) as UDI8. The availability of this Radio Access Bearer (RAB) is controlled through
multiRabUdi8Available [RNC, 0=FALSE, Binary, Fixed].
 Streaming Circuit Switched 57.6. This Radio Access Bearer (RAB) provides a Streaming class connection
between the UE and Circuit Switched Core Network with guaranteed throughput of up to 57.6kb and guaranteed
low latency.
 Streaming Packet Switched 16/64. This Radio Access Bearer (RAB) provides a Streaming class connection
between the UE and the Packet Switched Core Network with guaranteed throughput of up to 57.6kb on the
downlink and 16kb in the uplink. Latency is not guaranteed.
 Streaming Packet Switched 16/64 plus Interactive Packet Switched 8/8. This Radio Access Bearer (RAB)
provides a Streaming class connection between the UE and the Packet Switched Core Network with guaranteed
throughput of up to 57.6kb on the downlink and 16kb in the uplink plus an interactive class 8kb uplink, 8kb
downlink Packet Switched connection between the UE and Packet Switched Core Network. Throughput is only
guaranteed for the Streaming class connection. Latency is not guaranteed for either connection.
 Streaming Packet Switched 16/128. This Radio Access Bearer (RAB) provides a Streaming class connection
between the UE and the Packet Switched Core Network with guaranteed throughput of up to 112kb on the
downlink and 16kb in the uplink. Latency is not guaranteed.
 Streaming Packet Switched 16/128 plus Interactive Packet Switched 8/8. This Radio Access Bearer (RAB)
provides a Streaming class connection between the UE and the Packet Switched Core Network with a guaranteed
throughput of up to 112kb on the downlink and 16kb in the uplink plus an interactive class 8kb uplink, 8kb downlink
Packet Switched connection between the UE and Packet Switched Core Network. Throughput is only guaranteed
for the Streaming class connection. Latency is not guaranteed for either connection. The availability of this Radio
Access Bearer (RAB) is controlled through psStreaming128 [RNC, 0=FALSE, Binary, Fixed].
 Interactive Packet Switched HSDPA with 384 uplink. This Radio Access Bearer provides an interactive
connection between the UE and Packet Switched Core Network of 1.8Mb on the downlink and 384kb on the
uplink. Neither latency nor throughput is guaranteed. The availability of this Radio Access Bearer (RAB) is
controlled through allow384HsRab [RNC, 1=TRUE, Binary, Fixed].
 Interactive Packet Switched HSDPA with 64 uplink. This Radio Access Bearer provides an interactive
connection between the UE and Packet Switched Core Network of 1.8Mb on the downlink and 64kb on the uplink.
Neither latency nor throughput is guaranteed.
 Interactive Packet Switched DCH/DCH. This Radio Access Bearer (RAB) provides an interactive connection
between the UE and Packet Switched Core Network of 64kb, 128kb or 384kb on the uplink and 64kb, 128kb or
384kb on the downlink. Neither latency nor throughput is guaranteed. The initial Dedicated Channel (DCH)
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 36 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
selected for all non-HSDPA capable mobiles requesting a Packet Switched Interactive connection is 64/64. The
availability of the 128/128 Radio Access Bearer (RAB) is controlled through state128_128Supported [RNC,
1=TRUE, Binary, Fixed].
 Interactive Packet Switched EUL/HS. This Radio Access Bearer (RAB) provides an interactive connection
between the UE and Packet Switched Core Network using Enhanced Uplink (EUL) or HSUPA on the Uplink and
HSDPA on the Downlink.
Ericsson supports many types of Radio Access Bearers (RABs) as shown above; however, our end to
end network does not currently support Differentiated Service through the use of QoS profiles.
Our current implementation supports only the following Radio Access Bearer (RAB) configurations.
 Conversational Circuit Switched AMR 12.2kb for Speech.
 Conversational Circuit Switched Speech AMR 12.2kb for Speech plus Interactive Packet Switched 64/64 or 0/0
(SP64/SP0). This is also referred to as MultiRAB.
 Interactive Packet Switched 64/64 for non-HSDPA capable UEs. Up-switching allows for all combinations of 64,
128, and 384 on the Uplink and Downlink. Down-switching allows the use of common channels (RACH and
FACH) for User Plane data.
 Interactive Packet Switched 64kb or 384kb uplink with HSDPA downlink for UEs with HSDPA capability.
 Interactive Packet Switched Enhanced Uplink (EUL) with HSDPA downlink for UEs with EUL/HS capability.
 Conversational Circuit Switched Speech AMR 12.2kb for Speech plus Interactive Packet Switched 384kb or 64kb
uplink with HSDPA downlink for UEs with HSDPA capability. This is also referred to as HS MultiRAB
2.
Mobile Origination / Termination
The establishment of a Radio Access Bearer (RAB) in the case of a Mobile Origination or Termination
begins with either a RACH on the uplink, or a Page on the downlink. The establishment of an RRC
Connection is identical to the process used in Figure 4 within the Idle Mode section except that the
resulting Transparent Message Transfer connection between the UE and Core Network (CN) element
specifies a Service Request for a User Plane connection. Based upon the type of Service requested, the
Core Network Sends a RAB ASSIGNMENT REQUEST to the Serving Radio Network Controller (SRNC)
indicating the RAB ID.
The Serving Radio Network Controller (SRNC) determines the new Radio Connection based upon the
type of Service Requested by the Core Network taking into consideration any existing Radio Connections
between it and the UE. There are also functions as described in the following subsections that determine
the treatment of the Service Request. Each is considered independent of the others. The parameters that
guide the operation of each function are described within context.
1.
Paging
There are two primary uses for paging. One is to inform UEs of an incoming call, the other is to inform
UEs of new System Information broadcast on the Broadcast Control CHannel (BCCH). Pages for calls
can be sent from either the Packet Switched or the Circuit Switched core network. A UE may be paged
while it is in Idle Mode, CELL_FACH state or in CELL_DCH state.
In Idle Mode, the Secondary Common Control Physical CHannel (S-CCPCH) and the Paging Indicator
CHannel (PICH) are used. The Paging Indicator CHannel (PICH) power is set relative to the Primary
Common Pilot CHannel (PCPICH) through pichPower [Cell, -7, dB, Fixed].
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 37 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 The Secondary Common Control Physical CHannel (S-CCPCH) carries the Paging CHannel (PCH) logical
channel. The Paging CHannel (PCH) power is set relative to the Primary Common Pilot CHannel (PCPICH)
through pchPower [RNC, -4, 0.1dB, Fixed]. The Paging CHannel (PCH) is used to carry the Radio Resource
Control (RRC) Message “Paging type 1” which carries the actual paging message from the Core Network.
 In order to conserve UE battery life, the UE does not always read the Paging CHannel (PCH). The Paging
Indicator CHannel (PICH) is used to indicate when the UE should read the Paging CHannel (PCH). Each Paging
Indicator CHannel (PICH) frame consists of a number of Paging Indicators. The UEs are divided into a number of
groups, and each group reads a specific Paging Indicator that tells if it should read the Paging CHannel (PCH).
The interval at which the UE reads the Paging Indicator CHannel (PICH) is determined by its own International
Mobile Subscriber Identity (IMSI) and the Discontinuous Reception (DRX) Cycle Length.
The Discontinuous Reception (DRX) Cycle Length = 2k * 10ms
Where:
 k = cnDrxCycleLengthCs [RNC, 7=1280, coeff, Fixed] for Circuit Switched services cnDrxCycleLengthPs [RNC,
7=1280, coeff, Fixed] for Packet Switched services and utranDrxCycleLength [RNC, 5=320, coeff, Fixed] for UEs
in URA_PCH State.
 10ms is equal to the duration of a System Frame
In CELL_FACH state or in CELL_DCH state a connection exists between the UTRAN and the UE. The
RRC message "Paging type 2" is used to carry paging information over the dedicated connection.
The noOfPagingRecordTransm [RNC, 2, Integer, Fixed] controls the number of times a single page
from the Core Network will be sent by the UTRAN.
UEs in Idle Mode are informed of new System Information broadcast on the Broadcast Control CHannel
(BCCH) through consecutive “Paging type 1” messages. The number of times a UE (that uses maximum
possible DRX cycle length) hears the updated system information is defined by the parameter
noOfMaxDrxCycles [RNC, 1, DRX cycles, Fixed].
5.2.2.2
Admission Control
Admission Control is a function that determines if a new radio link can be allowed on the cell given the
cell’s current resource load. New radio links can be requested for Call Origination, Termination,
Handover or when existing radio links are modified.
Transport resources (Iub) are not considered during Admission Control procedures and as such do not
have any affect on Admission Control.
When a request is made of Admission Control, Service Classes (Guaranteed, Guaranteed-HS and NonGuaranteed) and Setup Types (Handover and Non-Handover) are used to allow for prioritization among
requests for different types of radio links.
The following radio connection types (supported by AT&T) correspond to the Guaranteed Service Class:
 Stand alone Signaling Radio Bearers (SRB)
 Conversational Circuit Switched Speech AMR 12.2kb
 Conversational Circuit Switched Speech AMR 12.2kb plus Interactive Packet Switched 0kb/0kb (SP0).
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 38 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
The following radio connection types (supported by AT&T) correspond to the Non-Guaranteed Service
Class:
 Interactive Packet Switched 64/64, 64/128, 128/128 and 64/384
 Conversational Circuit Switched Speech AMR 12.2 plus Interactive Packet Switched 64kb/64kb (SP64)
The following radio connection types (supported by AT&T) correspond to the Guaranteed-HS Service
Class:
 Interactive Packet Switched 384/HS
 Interactive Packet Switched 64/HS
 Conversational Circuit Switched Speech AMR 12.2kb for Speech plus Interactive Packet Switched 384kb or 64kb
uplink with HSDPA for downlink
The first decisions made to admit or block Radio Link admission requests are based upon two algorithms
that use the following two configurable parameters. See the figure below.
 Admission Control blocks new radio link admission requests for HSDPA when the number of users assigned to the
High Speed Downlink Shared CHannel (HS-DSCH) in the cell exceeds hsdpaUsersAdm [Cell, 10, Users, Var.].
This configurable parameter does not apply to requests made as a result of Cell Change (mobility). The total
number of HS users in the cell is limited by maxNumHsdpaUsers [Cell, 16, Users, Var.].
 Admission Control blocks admission requests for a radio link in compressed mode when the current number of
radio links exceeds compModeAdm [Cell, 15, Radio Links, Var.].
 Admission control will block admission for an E-DCH user requesting the cell as serving cell if the total number of
serving cell E-DCH users including the requested is greater than eulServingCellUsersAdm [Cell, 4, E-DCH users,
Fixed].
 Admission control will block admission for an E-DCH user requesting the cell as non-serving cell if the total number
of non-serving cell E-DCH users including the requested is greater than eulNonServingCellUsersAdm [Cell, 10,
E-DCH users, Fixed].
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 39 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 5: Admission Control (Radio Link Request)
HS Call?
Y
# of HS users >
hsdpaUsersAdm?
N
Radio
Link
Request
N
1
Block!
N
In Compressed Mode?
Y
N
Y
# of RL >
compModeAdm?
Y
In addition to specifying the Service Class and Setup Type, the Radio Link Request also includes an
estimation of each of the following:
 Number of downlink Channelization Codes
 Usage of uplink and downlink Spreading Factors
 Amount of downlink Non-HS Power
 Number of uplink and downlink Air Speech Equivalents (ASE)
 Amount of Node B Hardware utilized.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 40 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 Downlink Channelization Codes. In order to reserve Channelization Codes for Handover, admission is blocked
for all Guaranteed / Non-Handover and Guaranteed-HS / Non-Handover requests when Channelization Code
utilization exceeds dlCodeAdm [Cell, 70, %, Var.] of the total Channelization Codes in the cell. Furthermore, NonGuaranteed / Non-Handover admission requests are blocked when Channelization Code utilization exceeds
dlCodeAdm [Cell, 70, %, Var.] – beMarginDlCode [Cell, 1, 5%, Var.] of the total Channelization Codes in the cell.
See the figure below.
Figure 6: Admission Control (DL Channelization)
1
Y
Handover?
N
Admit!
N
Guaranteed or
Guaranteed HS?
Y
Channelization Code %
Utilization > dlCodeAdm?
Y
N (Non-Guaranteed)
Channelization Code %
utilization > dlCodeAdm beMarginDlCode ?
Y
Block!
N
Admit!
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 41 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 Uplink and Downlink Spreading Factor usage. The Histogram Monitor keeps track of Spreading Factor usage
in the uplink and downlink. It also measures the number of Compressed Mode radio links and the number of HS
serving radio links in the cell in order to allow or deny requests for either Handover or Non-Handover based upon
Spreading Factor utilization.
Non-Guaranteed admission requests of Spreading Factor 8 in the downlink are denied when the use of
Spreading Factor 8 exceeds sf8Adm [Cell, 8, Radio Links, Fixed]. The 384kb Radio Access Bearer uses
Spreading Factor 8 on the downlink.
Non-Guaranteed admission requests of Spreading Factor 16 in the downlink are denied when the use of
Spreading Factor 16 exceeds sf16Adm [Cell, 16, Radio Links, Var.]. The 128kb Radio Access Bearer uses
Spreading Factor 16 on the downlink.
Non-Guaranteed admission requests of Spreading Factor 32 in the downlink are denied when the use of
Spreading Factor 32 exceeds sf32Adm [Cell, 32, Radio Links, Var.]. The 64kb Radio Access Bearer uses
Spreading Factor 32 on the downlink.
Guaranteed admission requests of Spreading Factor 16 in the downlink are denied when the use of Spreading
Factor 16 (Streaming 16kb/128kb) exceeds sf16gAdm [Cell, 16, Radio Links, Var.]. However, AT&T does not
currently support any Guaranteed Radio Access Bearers that use Spreading Factor 16.
Guaranteed HS or Non-Guaranteed admission requests of Spreading Factor 16 in the uplink (64kb) are denied
when the use of Spreading Factor 16 in the uplink exceeds sf16AdmUl [Cell, 50, Radio Links, Var.].
Guaranteed HS or Non-Guaranteed admission requests of Spreading Factor 8 in the uplink (128kb) are denied
when the use of Spreading Factor 8 in the uplink exceeds sf8AdmUl [Cell, 8, Radio Links, Var.].
Guaranteed HS admission requests of Spreading Factor 4 in the uplink (384kb) are denied when the use of
Spreading Factor 4 in the uplink exceeds sf4AdmUl [Cell, 6, Radio Links, Var.].
The sf4AdmUl [Cell, 6, Radio Links, Var.] parameter is Cell based relative to the RNC based
allow384HsRab [RNC, 1=TRUE, Binary, Fixed] parameter. Given this, the number of cells where
384kb/HSDPA is possible within the RNC can be controlled.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 42 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 7: Admission Control (Spreading Factor Usage)
SF 8s (384k) in DL >
sf8Adm?
Y
N
SF 16s (128k) in DL >
sf16Adm?
Y
N
SF 32s (64k) in DL >
sf32Adm?
Y
N
SF 16s (64k) in UL >
sf16AdmUl?
Admit!
Block!
Y
N
SF 4s (128) in UL >
sf8AdmUl?
Y
N
SF 4s (384) in UL >
sf4AdmUl?
Y
 Downlink Non-HS Power / Soft Congestion. Downlink power utilization is measured in the cell. In addition to
Admission Control taking the following actions based upon Downlink power utilization, a Soft Congestion
mechanism is triggered. Upon Admission Control blocking a non 384kb Downlink Admission request, the
mechanism Down-Switches the Downlink for one existing Non-Guaranteed Service Class connection to the next
lowest rate. 384kb Downlink Radio Access Bearer (RAB) requests do not trigger Down-Switches since all 384kb
Radio Access Bearers (RABs) result from Up-Switches and under Congested conditions, the Up-Switch request
would be blocked.
Transmitted Code Power utilization is monitored and admission is blocked for all Guaranteed / Non-Handover and
Non-Guaranteed / Handover requests when the Transmitted Code Power utilization exceeds pwrAdm [Cell, 75, %,
Var.] of maximumTransmissionPower [Cell, 400, 0.1dBm, Var.] which sets the maximum power available in the
cell at the Reference Point (antenna connector).
Non-Guaranteed / Non-Handover admission requests are blocked when the downlink transmitted carrier power
utilization exceeds pwrAdm [Cell, 75, %, Var.] – beMarginDlPwr [Cell, 10, %, Var.] of
maximumTransmissionPower [Cell, 400, 0.1dBm, Var.].
Guaranteed / Handover and Guaranteed-HS / <any> are allowed up to the limit set by pwrAdm [Cell, 75, %,
Var.] + pwrAdmOffset [Cell, 10, %, Var.] of maximumTransmissionPower [Cell, 400, 0.1dBm, Var.].
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 43 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 8: Admission Control (DL Power)
1
Guaranteed / Non-HO or
Non-Guaranteed / HO?
Y
Code Power > pwrAdm % of
maximumTransmissionPower
?
N
Y
N
Admit!
N
Non-Guaranteed / NonHandover?
Y
N (Guaranteed / Handover
Code Power > pwrAdm %
- beMarginDlPwr % of
maximumTransmissionPower
?
Y
or Guaranteed HS / <any>)
Code Power > pwrAdm %
+ pwrAdmOffset % of
maximumTransmissionPower
?
Y
Block!
N
Admit!
 Air Speech Equivalent (ASE). The Air Speech Equivalent (ASE) Admission Policy is used to control the load in
both the uplink and the downlink. The table below shows the number of Air Speech Equivalents (ASEs) per AT&T
supported Radio Access Bearer (RAB).
Table 14: Air Speech Equivalents (ASE)
Radio Connection Type
ND-00150
Rev. 3.0 09/09/2007
ASEs
Signaling Radio Bearer
0.61
Conversational Circuit Switched Speech AMR 12.2kb
1.61
Interactive Packet Switched 64kb (UL or DL)
8.32
Interactive Packet Switched 128kb (UL or DL)
16.03
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 44 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Interactive Packet Switched 384kb (UL for HS or DL)
40.27
HS for Downlink – A-DCH only
0.61
Multi RAB 64/64 (UL and DL)
9.32
Multi RAB HS 64/HS
9.32 / 1.61
Multi RAB HS 384/HS
41.27 / 1.61
The Air Speech Equivalent (ASE) provides a unit of Uu interface load. Through its use in the Admission Control
algorithm, increases in noise in the uplink and downlink as a function of loading can be considered before the
Radio Link is established.
For the Uplink, the Air Speech Equivalent (ASE) is monitored and admission is blocked for all Guaranteed /
Non-Handover, Non-Guaranteed / Handover and Guaranteed-HS / Non-Handover requests when the number of
Air Speech Equivalents exceeds aseUlAdm [Cell, 500, ASE, Var.]. Non-Guaranteed / Non-Handover requests are
blocked when the number of Air Speech Equivalents exceeds aseUlAdm [Cell, 500, ASE, Var.] - beMarginAseUl
[Cell, 0, ASE, Var.]. Guaranteed / Handover and Guaranteed-HS / Handover requests are blocked when the
number of Air Speech Equivalents exceeds aseUlAdm [Cell, 500, ASE, Var.] + aseUlAdmOffset [Cell, 40, ASE,
Var.]. See the figure below.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 45 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 9: Admission Control (Uplink ASE Utilization)
1
Guaranteed / Non-HO,
Non-Guaranteed / HO or
Guaranteed-HS / NonHO?
Y
# of ASEs > aseUlAdm?
Y
N
N
Admit!
N
Non-Guaranteed / NonHandover?
Y
# of ASEs > aseUlAdm beMarginAseUl?
Y
N (Guaranteed / Handover or
Guaranteed HS / Handover)
# of ASEs > aseUlAdm +
aseUlAdmOffset?
Y
Block!
N
Admit!
For the Downlink, the Air Speech Equivalent (ASE) is monitored and admission is blocked for all Non- Guaranteed
/ Handover, Guaranteed / <any> and Guaranteed-HS / <any> requests when the number of Air Speech
Equivalents exceeds aseDlAdm [Cell, 500, ASE, Var.]. Non-Guaranteed / Non-Handover requests are blocked
when the number of Air Speech Equivalents exceeds aseDlAdm [Cell, 500, ASE, Var.] – beMarginAseDl [Cell, 0,
ASE, Var.]. See the figure below.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 46 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 10: Admission Control (Downlink ASE Utilization)
1
Non-Guaranteed / HO,
Guaranteed / <any> or
Guaranteed-HS / <any>?
Y
N (Non-Guaranteed / Non-
# of ASEs > aseDlAdm?
Y
N
Handover)
Admit!
# of ASEs > aseDlAdm beMarginAseDl?
Y
Block!
N
Admit!
 Node B Hardware utilized. The Hardware Monitor provides Admission Control based upon an estimation of the
hardware (Channel Elements) utilized in the Uplink and Downlink.
For the Uplink, the Hardware Utilization is monitored and admission is blocked for all Guaranteed / NonHandover, Non-Guaranteed / Handover and Guaranteed-HS / Non-Handover requests when the percent of Uplink
Hardware Utilized exceeds ulHwAdm [Site, 80, %, Var.]. Non-Guaranteed / Non-Handover requests are blocked
when the percent of Uplink Hardware Utilized exceeds ulHwAdm [Site, 80, %, Var.] – beMarginUlHw [Site, 0, %,
Var.]. Guaranteed / Handover and Guaranteed-HS / Handover requests are blocked when the percent of Uplink
Hardware Utilized arrives at 100%. See the figure below.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 47 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 11: Admission Control (Uplink Hardware Utilization)
1
Guaranteed / Non-HO,
Non-Guaranteed / HO or
Guaranteed-HS / NonHO?
Y
% UL HW utilization >
ulHwAdm?
Y
N
N
Admit!
N
Non-Guaranteed / NonHandover?
Y
% UL HW utilization >
ulHwAdm - beMarginUlHw?
Y
N (Guaranteed / Handover or
Guaranteed HS / Handover)
Admit until 100% of
UL HW is utilized!
Block!
For the Downlink, the Hardware Utilization is monitored and admission is blocked for all Guaranteed / NonHandover, Non-Guaranteed / Handover and Guaranteed-HS / Non-Handover requests when the percent of
Downlink Hardware Utilized exceeds dlHwAdm [Site, 100, %, Var.]. Non-Guaranteed / Non-Handover requests
are blocked when the percent of Downlink Hardware Utilized exceeds dlHwAdm [Site, 100, %, Var.] –
beMarginDlHw [Site, 0, %, Var.]. Guaranteed / Handover and Guaranteed-HS / Handover requests are blocked
when the percent of Downlink Hardware Utilized arrives at 100%. See the figure below.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 48 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 12: Admission Control (Downlink Hardware Utilization)
1
Guaranteed / Non-HO,
Non-Guaranteed / HO or
Guaranteed-HS / NonHO?
Y
% DL HW utilization >
dlHwAdm?
Y
N
N
Admit!
N
Non-Guaranteed / NonHandover?
Y
% DL HW utilization >
dlHwAdm - beMarginDlHw?
Y
N (Guaranteed / Handover or
Guaranteed HS / Handover)
Admit until 100% of
DL HW is utilized!
5.2.2.3
Block!
Emergency Call Redirect to 2G for Speech
If emergencyCallRedirect [RNC, 1=TRUE, Binary, Fixed] is set to TRUE, an emergency (911) call made
by a UE on the UMTS network will be redirected to GSM. The call will be established on the GSM
network after Cell Selection on the GSM network has taken place.
This procedure is applied when there is no existing Radio Connection. If there is an existing connection
between the UE and Packet Switched Core Network, the 911 call will be placed through the 3G network.
In this case, only the Cell ID of the serving cell will be used for location purposes.
The current recommendation is to enable this capability by setting emergencyCallRedirect [RNC,
1=TRUE, Binary, Fixed] to TRUE due to the fact that the E911 solution for WCDMA does not provide the
level of location detection accuracy provided by the GSM solution.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 49 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
4.
Uplink Pathloss Threshold for 384/HS
If Admission Control grants the request, and if ulPathlossCheckEnabled [Cell, FALSE, String, Var.] is
set to TRUE, the amount of Uplink pathloss for a 384/HS Radio Access Bearer (RAB) request is
determined. If the Uplink pathloss is greater than sf4UlPathlossThreshold [Cell, 170, dB, Var.] , then a
64k uplink Radio Access Bearer (RAB) is used instead of a 384kb Radio Access Bearer (RAB). This
check only occurs at establishment and therefore is technically not a Down-Switch. However, it can be
used to limit the number of HS capable UEs in 384kb uplink soft handover at the cell edge.
5.
Directed Retry to GSM for Speech
Speech requests without ongoing packet connections (Multi-RAB) are considered for Directed Retry to
GSM during RAB establishment based upon the setting of loadSharingDirRetryEnabled [RNC,
0=FALSE, Binary, Fixed]. If this configurable parameter is set to TRUE, and the WCDMA cell exceeds
loadSharingGsmThreshold [Cell, 100, %, Fixed] of pwrAdm [Cell, 75, %, Var.], the UTRAN requests a
blind inter-RAT handover for loadSharingGsmFraction [Cell, 100, %, Fixed] of the Directed Retry
candidates to the directedRetryTarget [Cell, N/A, N/A, Var.] configured GSM cell via the core network.
The current recommendation is to disable this capability by setting loadSharingDirRetryEnabled [RNC,
0=FALSE, Binary, Fixed] to FALSE. All other parameters associated with this function are simply
defaulted.
5.2.2.6
Inter-Frequency Load Sharing
If multiple UARFCNs are available at a given Node B loadSharingRrcEnabled [RNC, 0=FALSE, Binary,
Fixed] is set the TRUE, Inter-Frequency Load Sharing will determine if the WCDMA cell exceeds
loadSharingMargin [Cell, 0, %, Fixed] of pwrAdm [Cell, 75, %, Var.] at each call setup during Radio
Resource Control (RRC) Connection Establishment. If the cell exceeds loadSharingMargin [Cell, 0, %,
Fixed] of pwrAdm [Cell, 75, %, Var.], the UE will be directed to the UARFCN defined by the InterFrequency load sharing neighbor as indicated by the loadSharingCandidate [Nabr, N/A, N/A, Var.] flag.
The current recommendation is to disable this capability by setting loadSharingRrcEnabled [RNC,
0=FALSE, Binary, Fixed] to FALSE. All other parameters associated with this function are simply
defaulted.
5.2.2.7
Packet Switched RAB Determination
If the Service requested of the UTRAN is Interactive Packet Switched and the UE is HSDPA capable:
 The Radio Access Bearer options are 384/HS (if allow384HsRab [RNC, 1=TRUE, Binary, Fixed] is set to TRUE)
or 64/HS. The UE is then assigned based upon the setting of hsOnlyBestCell [RNC, 1=TRUE, Binary, Fixed] to
the best cell in the Active Set.
The current recommendation is to set the value of hsOnlyBestCell [RNC, 1=TRUE, Binary, Fixed] to
TRUE thereby allowing HSDPA to be supported on the best cell in the Active Set.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 50 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
If the Service requested of the UTRAN is Interactive Packet Switched and the UE is not HS capable,
packetEstMode [RNC, 1, Integer, Fixed] is used.
 If packetEstMode [RNC, 1, Integer, Fixed] =0, the attempt will be made to allocate the UE on RACH/FACH.
 If packetEstMode [RNC, 1, Integer, Fixed] =1, the attempt will be made to allocate the UE on 64/64.
 If packetEstMode [RNC, 1, Integer, Fixed] =2, then an attempt will be made to allocate the UE on 64/64, but if
Admission Control blocks the assignment to a 64/64, the UE is sent to RACH/FACH.
The current recommendation is to set the value of packetEstMode [RNC, 1, Integer, Fixed] =2 thereby
allowing an attempt at a 64kb/64kb Radio Access Bearer with fallback to RACH/FACH if you are denied.
The following table provides parameter ranges and default values involved Establishing a Call. They are
listed in the same order they were presented. The Level column indicates the network element that owns
the parameter. The class column indicates if the parameter is set based on Policy (must be set this way),
Fixed (recommended to be set this way) and Variable (set at your discretion).
5.2.2.8
Active Queue Management (AQM)
Active Queue Management improves throughput for TCP based applications by selectively dropping
packets when queues begin to reach overflow thus reducing the probability of the overflow occurring.
The capability is controlled by the configurable parameter activeQueueMgmt [RNC, 0=OFF, Binary,
Fixed].
3.
Mobility and Connection Management
This section contains the protocols and configurable parameters involved in maintaining a call once it has
been established. Measurement Fundamentals as they apply to Mobility Management and Power Control
are explained. Intra-RAT (UMTS) and Inter-RAT (UMTS to GSM) Idle Mode Cell Reselection, Connected
Mode Handover (including Inter-RAT) and HSDPA Cell Change are covered. Channel Switching and
Congestion Control as they occur after Call Establishment are also included.
1.
Measurement Fundamentals
Primary Common Pilot Channel (P-CPICH) Ec/No, Primary Common Pilot Channel (P-CPICH), Received
Signal Code Power (RSCP) and UE Transmitted power are the quantities measured by the UE that when
certain conditions are met; trigger events that may lead to one of the following:
 Cell Reselection in Idle Mode or CELL_FACH (intra or inter RAT)
 Handover in Connected Mode (CELL_DCH) (intra or inter RAT)
 HS Cell Change (intra or inter RAT)
CPICH Ec/No and CPICH RSCP are explained in the Design Criteria section.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 51 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
2.
Cell Reselection in Idle Mode or CELL_FACH
In Idle Mode, the UE maintains a relationship with both sides of the Core Network (PS and CS) in order to
allow for the establishment of calls. First, an event has to be triggered based upon configurable
parameters sent in System Information Block (SIB), then the Cell Reselection candidates are ranked
according to signal level and quality. In CELL_FACH, the UE is actually Connected Mode but is using
Common Channels to relay User Plane data.
1.
Idle Mode Cell Reselection Triggers
When in Idle Mode, URA_PCH or CELL_FACH, the UE communicates with one serving cell (no Soft
Handover). The UE “camps” on this cell until one of the following triggers occurs:
 The cell is no longer suitable in terms of signal level (Srxlev) and quality (Squal). See “Camping on a Suitable
Cell” in the Idle Mode section.
 The quality (Squal) of the serving cell falls below sIntraSearch [Cell, 22=10, dB, Fixed] at which point the UE will
search for a better quality Intra-Frequency cell.
 If Inter-Frequency neighbors are assigned to the cell and the quality (Squal) of the serving cell falls below
sInterSearch [Cell, 0, dB, Fixed]. If there are no Inter-Frequency neighbors defined on the cell, the setting of
sInterSearch [Cell, 0, dB, Fixed] has no impact.
 If Inter-RAT neighbors are assigned to the cell and either of the following two conditions are met:
 The serving cell’s CPICH Ec/No becomes equal to or below qQualMin [Cell, -19, dB, Fixed] + sRatSearch
[Cell, 4, dB, Fixed].
 The serving cell’s CPICH RSCP becomes equal to or below qRxLevMin [Cell, -115, dBm, Fixed] + sHcsRat
[Cell, -105, dB, Fixed]. Negative values for sHcsRat [Cell, -105, dB, Fixed] are interpreted by the UE as 0.
 If there are no Inter-RAT neighbors defined on the cell, the settings of sRatSearch [Cell, 4, dB, Fixed] and
sHcsRat [Cell, -105, dB, Fixed] have no impact.
The sHcsRat [Cell, -105, dB, Fixed] functionality is supported by CR130 which was implemented in the
Qualcomm chipset in October of 2006. As such, it will not be advantageous to utilize sHcsRat [Cell, 105, dB, Fixed] until most of the UE in production support it.
If interFreqFddMeasIndicator [Cell, 0=FALSE, Binary, Fixed] is set to TRUE, a UE in CELL_FACH will
evaluate Inter-Frequency and Inter-RAT neighbors using the same triggering mechanism used in Idle
Mode. The UE performs Inter-frequency and Inter-RAT measurements during FACH measurement
occasions. FACH measurement occasions are defined as being the frames where the following equation
is fulfilled.
SFN = C-RNTI mod n * 2k
Where:
 SFN is the System Frame Number
 C-RNTI is the Cell Radio Network Temporary Identity
 n is 0, 1, 2 etc.
 k is fachMeasOccaCycLenCoeff [Cell, 4, Integer, Fixed]
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 52 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.2.2
Candidate Ranking
After the UE has been triggered to perform measurements, the measurements that satisfy the Cell
Selection S criteria (Squal and Srxlev are positive for UMTS neighbors or only Srxlev is positive for GSM
neighbors) are ranked according to the R criteria.
R(s) = Qmeas(s) + qHyst(s)
R(n) = Qmeas(n) - qOffset(s,n)
Where:
 s is the serving cell
 n is the neighbor cell
 Qmeas is either the CPICH RSCP (qualMeasQuantity [Cell, 2=CPICH_EC_NO, String, Fixed] =CPICH_RSCP) or
the CPICH Ec/No (qualMeasQuantity [Cell, 2=CPICH_EC_NO, String, Fixed] =CPICH_EC_NO) of the
neighboring UMTS cell. The ranking for a GSM neighbor is always done using the serving cell’s CPICH RSCP
and the neighboring GSM cell’s Received Signal Level.
 qHyst(s) is a hysteresis value read in System Information Block (SIB) 3 based upon qHyst1 [Cell, 2, dB, Fixed] if
qualMeasQuantity [Cell, 2=CPICH_EC_NO, String, Fixed] =CPICH_RSCP or qHyst2 [Cell, 2, dB, Fixed] if
qualMeasQuantity [Cell, 2=CPICH_EC_NO, String, Fixed] =CPICH_EC_NO.
 qOffset is an offset between the serving cell and the neighboring cell that can be used to adjust the border
between the two cells. The parameter is set per neighbor using qOffset1sn if qualMeasQuantity [Cell,
2=CPICH_EC_NO, String, Fixed] =CPICH_RSCP or qOffset2sn [Nabr, 0, dB, Fixed] if qualMeasQuantity [Cell,
2=CPICH_EC_NO, String, Fixed] =CPICH_EC_NO. qOffset1sn(UtranRelation) [Nabr, 0, dB, Fixed] is used for
Intra-Frequency neighbor relationships, and qOffset1sn(GsmRelation) [Nabr, 7, dB, Fixed] is used for Inter-RAT
or neighbor relationships.
The initial ranking is done using the measurement quantity CPICH RSCP.
 If a GSM cell is ranked better than the serving cell for the time interval treSelection [Cell, 1, seconds, Fixed], the
UE performs Cell Reselection to that cell.
 If a UMTS cell is ranked better than the serving cell for the time interval treSelection [Cell, 1, seconds, Fixed] one
of the following two possibilities will occur:
If the measurement quantity for Cell Reselection is set to CPICH RSCP (qualMeasQuantity [Cell,
2=CPICH_EC_NO, String, Fixed]), the UE performs Cell Reselection.
If the measurement quantity for Cell Reselection is set to CPICH Ec/No (qualMeasQuantity [Cell,
2=CPICH_EC_NO, String, Fixed]), the UE performs a second ranking of the UMTS cells based on CPICH Ec/No
and performs Cell Reselection to the best quality cell.
5.3.3 Handover in Connected Mode (CELL_DCH) – Intra-Frequency
Immediately after Call Setup, a UE is served by only one site. During RRC Connection Establishment the
Serving Radio Network Controller (SRNC) sends the UE a MEASURMENT CONTROL message
containing a list of neighbors and parameters values used to trigger neighbor measurements. This
information was also sent in System Information Blocks (SIBs) 11 and 12 while the UE was in Idle Mode,
so the UE has the information it needs in order to make neighbor measurements before it receives a
MEASURMENT CONTROL message.
In Connected Mode, the UE continuously measures the Primary Common Pilot Channel (P-CPICH)
Ec/No of all the cells in its Active Set (cells that are in soft handover), Monitored Set (cells which are on
the neighbor list, but are not in soft handover) and Detected Set (cells that are not in the neighbor list).
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 53 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
The UE Filters, Offsets and Weights the measurements to ensure the criteria for one of the following
Events are met. If one of the criteria is met, the UE sends a MEASUREMENT REPORT to the RNC.
 Active Set Addition (Event 1a)
 Active Set Deletion (Event 1b)
 Active Set Replacement of worst cell (Event 1c)
 Change of Best Cell (Event 1d)
5.3.3.1
Active Set Addition (Event 1a)
If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) Ec/No of a cell not in the
Active Set becomes greater than the Best Cell in the Active Set by reportingRange1a [RNC, 6, 0.5dB,
Fixed] + hysteresis1a [RNC, 0, 0.5dB, Fixed] / 2, for a time equal to timeToTrigger1a [RNC, 11=320,
ms, Fixed] , then event 1a occurs. The UE then sends a MEASUREMENT REPORT message for event
1a to the Serving Radio Network Controller (SRNC). If the number of cells in the Active Set is less than
maxActiveSet [RNC, 3, Radio Links, Fixed], the cell is considered for addition to the Active Set. If the
number of cells in the Active Set is equal to maxActiveSet [RNC, 3, Radio Links, Fixed], then the cell is
proposed as a replacement for the cell with the worst quality in the Active Set.
If the cell under consideration is not in the Monitored Set (not a configured neighbor), and its CPICH Ec/No
is more than releaseConnOffset [RNC, 120, 0.1dB, Fixed] greater than the Best Cell in the Active Set, the
call is disconnected. This is done to protect surrounding cells from Uplink interference. The UE will
continue to send the event 1a MEASUREMENT REPORT each reportingInterval1a [RNC, 3=1, seconds,
Fixed] until the Active Set is updated or the condition responsible for triggering the event is no longer valid.
Figure 13: Event 1a Trigger
CPICH Ec/No
Best Cell
Candidate Cell
hysteresis1a
reportingRange1a
Time
timeToTrigger1a
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
MEASUREMENT
REPORT to RNC
Page 54 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.3.2
Active Set Deletion (Event 1b)
If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) Ec/No (if measQuantity1
[Cell, 2=CPICH_EC_NO, String, Fixed] = CPICH_EC_NO or RSCP if measQuantity1 [Cell,
2=CPICH_EC_NO, String, Fixed] = CPICH_RSCP) of one of the cells in the Active Set becomes less
than the Best Cell in the Active Set by reportingRange1b [RNC, 10, 0.5dB, Fixed] - hysteresis1b [RNC,
0, 0.5dB, Fixed] / 2, for a time equal to timeToTrigger1b [RNC, 12=640, ms, Fixed] , then event 1b
occurs. The UE then sends a MEASUREMENT REPORT message for event 1b to the Serving Radio
Network Controller (SRNC). The cell is then removed from the Active Set.
If the call is supporting HSDPA, then Event 1b might also trigger a change of the Serving HS cell.
Figure 14: Event 1b Trigger
CPICH Ec/No
Best Cell
reportingRange1b
Cell in the Active Set
hysteresis1b
MEASUREMENT
REPORT to RNC
timeToTrigger1b
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 55 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.3.3
Active Set Replacement of worst cell (Event 1c)
If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) Ec/No (if measQuantity1
[Cell, 2=CPICH_EC_NO, String, Fixed] = CPICH_EC_NO or RSCP if measQuantity1 [Cell,
2=CPICH_EC_NO, String, Fixed] = CPICH_RSCP) of a cell not in the Active Set becomes greater than the
Worst Cell in the Active Set by hysteresis1c [RNC, 2, 0.5dB, Fixed] / 2, for a time equal to
timeToTrigger1c [RNC, 11=320, ms, Fixed] , and the number of cells in the Active Set is equal to
maxActiveSet [RNC, 3, Radio Links, Fixed] , then event 1c occurs. The UE then sends a
MEASUREMENT REPORT message for event 1c to the Serving Radio Network Controller (SRNC) and
the cell is proposed as a replacement for the cell with the worst quality in the Active Set.
If the cell under consideration is not in the Monitored Set (not a configured neighbor), and its CPICH Ec/No
is more than releaseConnOffset [RNC, 120, 0.1dB, Fixed] greater than the Best Cell in the Active Set, the
call is disconnected. This is done to protect surrounding cells from Uplink interference.
The UE will continue to send the event 1c MEASUREMENT REPORT each reportingInterval1c [RNC,
3=1, seconds, Fixed] until the Active Set is updated or the condition responsible for triggering the event is
no longer valid.
If the call is supporting HSDPA, then Event 1c might also trigger a change of the Serving HS cell.
Figure 15: Event 1c Trigger
CPICH Ec/No
Best Cell
New Cell
hysteresis1c
Worst Cell in AS
timeToTrigger1c
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
MEASUREMENT
REPORT to RNC
Page 56 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.3.4
Change of Best Cell (Event 1d)
If the Filtered and Offset Primary Common Pilot Channel (P-CPICH) Ec/No of any cell in the Active Set
becomes greater than the Best Cell in the Active Set by hysteresis1d [RNC, 15, 0.5dB, Fixed] / 2, for a
time equal to timeToTrigger1d [RNC, 14=2560, ms, Fixed] , then event 1d occurs. The UE then sends a
MEASUREMENT REPORT message for event 1d to the Serving Radio Network Controller (SRNC).
Figure 16: Event 1d Trigger
CPICH Ec/No
Best Cell
Another Cell in AS
hysteresis1d
MEASUREMENT
REPORT to RNC
timeToTrigger1d
5.3.3.5
Filtering, Offsetting and Weighting for Intra-Frequency measurements
Filtering: Before Events 1a, 1b, 1c or 1d can occur, the measurements made by the UE are Filtered
according to the formula below:
Fn = (1-a) F n-1 + a M n
Where:
 Fn = The updated measurement.
 Fn-1 = the last (old) filtered measurement result.
 Mn = the Ec/No as measured by the UE.
 a = 1/2(k/2) where k is filterCoefficient1 [RNC, 2, coeff, Fixed].
Offsetting: The updated measurement (Fn) is then offset by individualOffset(UtranCell) [Cell, 0, 0.5dB,
Fixed].
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 57 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Weighting: For Events 1a, and 1b, w1a [RNC, 0, 0.1unit, Fixed] and w1b [RNC, 0, 0.1unit, Fixed]
respectively can be added in order to give heavier weight to cells in the Active Set that are not the best
cell in the Active Set.
5.3.4 Handover in Connected Mode (CELL_DCH) – Inter-Frequency or Inter-RAT
In Connected Mode, the UE continuously measures the Primary Common Pilot Channel (P-CPICH)
Ec/No and Primary Common Pilot Channel (P-CPICH) RSCP of the Best Cell in the Active Set. When one
of the following Events occurs, the UE is commanded to either start or stop Compressed Mode (CM)
measurements for either Inter-RAT or Inter-Frequency neighbors.
The UE Filters, Offsets and Weights the measurements to ensure the criteria for one of the following
Events are met. If one of the criteria is met, the UE sends a MEASUREMENT REPORT to the RNC.
 Current Used Frequency is Below Threshold (Event 2d) – Begin CM
 Current Used Frequency is Above Threshold (Event 2f) – Cease CM
 UE Transmit power is Above Threshold (Event 6d) – Begin CM
 UE Transmit power is Below Threshold (Event 6b) – Cease CM
The Serving RNC then determines whether the UE makes Compressed Mode (CM) messages on InterFrequency or Inter-RAT neighbors based upon configurable parameters.
Lastly, upon receiving the MEASUREMENT REPORT from the UE, the Serving RNC sends a
MEASUREMENT CONTROL message to the UE with additional Event based criteria that the UE will use
to evaluate its Inter-Frequency or Inter-RAT neighbors.
If hsToDchTrigger(poorQualityDetected) [RNC, 1=TRUE, Binary, Fixed] is set to 1=ON, UEs with
HSDPA capability will be Down-Switched to an Interactive Packet Switched 64/64 Radio Access Bearer
(RAB) for Compressed Mode measurements. If hsToDchTrigger(poorQualityDetected) [RNC,
1=TRUE, Binary, Fixed] is set to 0=OFF, HSDPA capable UEs could drop due to their not being allowed
to make Compressed Mode measurements.
The following describes the triggering and evaluation mechanism involved in Inter-Frequency and InterRAT Handover. The Handover algorithm is the same for Speech and Interactive Packet Switched R99
Data. All Interactive Packet Switched R99 Data connections are Down-Switched to Interactive Packet
Switched 64/64 to order to make Compressed Mode (CM) measurements.
5.3.4.1
Begin Compressed Mode – Current Used Frequency is Below Threshold (Event 2d)
For Cells that meet the hho (section 1.7) criteria: If the Filtered, Offset and Weighted Primary
Common Pilot Channel (P-CPICH) Ec/No of the Best Cell in the Active Set becomes less than the absolute
threshold usedFreqThresh2dEcno(hho) [Cell, -12, dB, Fixed] - hysteresis2d [RNC, 4, 0.5 dB, Fixed] / 2,
for a time equal to timeToTrigger2dEcno [RNC, 320, ms, Fixed] , or if the Filtered, Offset and Weighted
Primary Common Pilot Channel (P-CPICH) RSCP of the Best Cell in the Active Set becomes less than the
absolute threshold usedFreqThresh2dRscp(hho) [Cell, -106 ±4, dBm, Fixed] - hysteresis2d [RNC, 4,
0.5 dB, Fixed] / 2, for a time equal to timeToTrigger2dRscp [RNC, 320, ms, Fixed] , then event 2d occurs.
The UE then sends a MEASUREMENT REPORT message for event 2d to
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 58 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
the Serving Radio Network Controller (SRNC). When the Serving Radio Network Controller (SRNC)
receives event 2d, it commands the UE to begin Compressed Mode measurements.
For Cells that meet the sho (section 1.7) criteria: If the Filtered, Offset and Weighted Primary
Common Pilot Channel (P-CPICH) Ec/No of the Best Cell in the Active Set becomes less than the absolute
threshold usedFreqThresh2dEcno(sho) [Cell, -15, dB, Fixed] - hysteresis2d [RNC, 4, 0.5 dB, Fixed] / 2,
for a time equal to timeToTrigger2dEcno [RNC, 320, ms, Fixed] , or if the Filtered, Offset and Weighted
Primary Common Pilot Channel (P-CPICH) RSCP of the Best Cell in the Active Set becomes less than the
absolute threshold usedFreqThresh2dRscp(sho) [Cell, -112, dBm, Fixed] - hysteresis2d [RNC, 4, 0.5
dB, Fixed] / 2, for a time equal to timeToTrigger2dRscp [RNC, 320, ms, Fixed] , then event 2d occurs.
The UE then sends a MEASUREMENT REPORT message for event 2d to the Serving Radio Network
Controller (SRNC). When the Serving Radio Network Controller (SRNC) receives event 2d, it commands
the UE to begin Compressed Mode measurements.
Figure 17: Event 2d Trigger (Begin Compressed Mode)
CPICH Ec/No
or
CPICH RSCP
hysteresis2d
Best Cell in the Active Set
usedFreqThresh2dEcno
or
usedFreqThresh2dRscp
MEASUREMENT
REPORT to RNC
timeToTrigger2dEcno
or
timeToTrigger2dRscp
For this section of the document, usedFreqThresh2dEcno and usedFreqThresh2dRscp apply when
the UE is served by its Serving Radio Network Controller (SRNC). These parameters do not apply if the
UE is served by a Drift Radio Network Controller (DRNC). For cases wherein the UE is served by a Drift
Radio Network Controller (DRNC), usedFreqThresh2dEcnoDrnc [RNC, -12, dB, Fixed] and
usedFreqThresh2dRscpDrnc [RNC, -106, dBm, Fixed] as configured on the SRNC apply.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 59 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.4.2
Cease Compressed Mode – Current Used Frequency is Above Threshold (Event 2f)
If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) Ec/No of the Best Cell in
the Active Set becomes greater than the absolute threshold usedFreqRelThresh2fEcno [RNC, 2, dB,
Fixed] + usedFreqThresh2dEcno + hysteresis2f [RNC, 2, 0.5dB, Fixed] / 2, for a time equal to
timeToTrigger2fEcno [RNC, 640, ms, Fixed] , and the Filtered, Offset and Weighted Primary Common
Pilot Channel (P-CPICH) RSCP of the Best Cell in the Active Set is greater than the relative threshold
usedFreqRelThresh2fRscp [RNC, 6, dB, Fixed] + usedFreqThresh2dRscp + hysteresis2f [RNC, 2,
0.5dB, Fixed] / 2, for a time equal to timeToTrigger2fRscp [RNC, 640, ms, Fixed] , then event 2f occurs.
The UE then sends a MEASUREMENT REPORT message for event 2f to the Serving Radio Network
Controller (SRNC). When the Serving Radio Network Controller (SRNC) receives event 2f, it commands
the UE to stop all Compressed Mode measurements.
Figure 18: Event 2f Trigger (Cease Compressed Mode)
CPICH Ec/No
or
CPICH RSCP
usedFreqRelThresh2dEcno + usedFreqRelThresh2fEcno
and
usedFreqRelThresh2dRscp + usedFreqRelThresh2fRscp
Best Cell in the Active
Set
hysteresis2f
MEASUREMENT
REPORT to RNC
timeToTrigger2dEcno
and
timeToTrigger2fRscp
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 60 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.4.3
Begin Compressed Mode – UE Transmit power is Above Threshold (Event 6d)
If txPowerConnQualMonEnabled [RNC, 0=FALSE, Binary, Fixed] is set to TRUE and the UE
transmitted power is at maximum for a time equal to timeToTrigger6d [RNC, 320, ms, Fixed] , then event
6d occurs. The UE then sends a MEASUREMENT REPORT message for event 6d to the Serving Radio
Network Controller (SRNC). When the Serving Radio Network Controller (SRNC) receives event 6d, it
commands the UE to begin Compressed Mode measurements.
Figure 19: Event 6d Trigger (Begin Compressed Mode)
Power
Maximum UE Tx Power
UE Transmission Power
MEASUREMENT
REPORT to RNC
timeToTrigger6d
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 61 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.4.4
Cease Compressed Mode – UE Transmit power is Below Threshold (Event 6b)
If txPowerConnQualMonEnabled [RNC, 0=FALSE, Binary, Fixed] is set to TRUE and the UE
transmitted power becomes less than the absolute threshold ueTxPowerThresh6b [RNC, 21, dB, Fixed]
for a time equal to timeTrigg6b [RNC, 1280, ms, Fixed] , then event 6b occurs. The UE then sends a
MEASUREMENT REPORT message for event 6b to the Serving Radio Network Controller (SRNC).
When the Serving Radio Network Controller (SRNC) receives event 6b, it commands the UE to stop
Compressed Mode measurements.
Figure 20: Event 6b Trigger (Cease Compressed Mode)
Power
ueTxPowerThresh6b
UE Transmission Power
MEASUREMENT
REPORT to RNC
timeTrigg6b
5.3.4.5
Filtering, Offsetting and Weighting for Inter-Frequency or Inter-RAT measurements
Filtering: Before Events 2d or 6d can occur, the measurements made by the UE are Filtered according
to the formula below:
Fn = (1-a) F n-1 + a M n
Where:
 Fn = The updated measurement.
 Fn-1 = the last (old) filtered measurement result.
 Mn = the Ec/No as measured by the UE.
 a = 1/2(k/2) where k is filterCoefficient2 [RNC, 2, coeff, Fixed] or filterCoeff6 [RNC, 3, coeff, Fixed] respectively for
Events 2x or 6x.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 62 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Offsetting: The updated measurement (Fn) is then offset by individualOffset(UtranCell) [Cell, 0, 0.5dB,
Fixed].
Weighting: For Events 2d, and 2f, usedFreqW2d [RNC, 10, 0.1unit, Fixed] or usedFreqW2f [RNC, 10,
0.1unit, Fixed] respectively can be added in order to give heavier weight to cells in the Active Set that are
not the best cell in the Active Set.
5.3.4.6
Whether to measure Inter-Frequency or Inter-RAT
If Compressed Mode measurements are required of the UE, the following parameters are considered:
 Inter-Frequency measurements can be made only if FddIfHoSupp [RNC, 0=FALSE, Binary, Fixed] =TRUE.
 Compressed Mode measurements of Inter-RAT neighbors can be made only if FddGsmHoSupp [RNC, 1=TRUE,
Binary, Fixed] =TRUE.
If all Inter-Frequency neighbors are within the same Serving Radio Network Controller (SRNC), hoType
[Cell, 1=GSM_PREFERRED, String, Fixed] determines if Inter-Frequency or Inter-RAT neighbors are
evaluated.
If however, all of the Inter-Frequency neighbors are not within the same Serving Radio Network Controller
(SRNC), a parameter called defaultHoType [Cell, 1=GSM_PREFERRED, String, Fixed] set per uarfcnDl
[Cell, N/A, Integer, Variable] for the Drift Radio Network Controller (DRNC) is used. This parameter has
been implemented due to a standards limitation in the Iur interface.
hoType [Cell, 1=GSM_PREFERRED, String, Fixed] and defaultHoType [Cell, 1=GSM_PREFERRED,
String, Fixed] have the following settings which determine how the UE will behave.
 If at least one cell in Active Set has hoType [Cell, 1=GSM_PREFERRED, String, Fixed] =0 (IF-Preferred), then
Inter-Frequency neighbors are evaluated.
 If at least one cell in Active Set has hoType [Cell, 1=GSM_PREFERRED, String, Fixed] =1 (GSM-Preferred), and
no cell has hoType [Cell, 1=GSM_PREFERRED, String, Fixed] =0 (IF-Preferred), then Inter-RAT neighbors are
evaluated.
 If all cells in the Active Set have hoType [Cell, 1=GSM_PREFERRED, String, Fixed] =2 (None), then neither InterFrequency nor Inter-RAT neighbors are evaluated.
5.3.4.7
Compressed Mode Measurement evaluation
Upon receiving either Event 2d or Event 6d from the UE, the Serving RNC sends a MEASUREMENT
CONTROL message to the UE with additional Event based criteria that the UE will use to evaluate the
results of the Compressed Mode (CM) measurements.
 The algorithm looks to see what initiated the Compressed Mode (CM) trigger.
 CPICH Ec/No from Event 2d
 CPICH RSCP from Event 2d
 UE Transmission Power from Event 6d
 If the Compressed Mode trigger measured Inter-Frequency or Inter-RAT measurements.
The following details the algorithms and configurable parameters that apply based upon the type of
trigger that initiated the Compressed Mode measurements.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 63 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
If the Event 2d reported by the UE indicated the trigger occurred due to CPICH Ec/No for Inter-RAT
measurements the following occurs:
 If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) Ec/No of the Best Cell in the Active
Set is less than usedFreqThresh2dEcno + utranRelThresh3aEcno [RNC, 2, dB, Fixed] – hysteresis3a [RNC, 4,
0.5dB, Fixed] / 2 and the Weighted absolute level of the GSM Broadcast Control CHannel (BCCH) is greater than
gsmThresh3a [RNC, -98, dBm, Fixed] for a time equal to timeToTrigger3a [RNC, 6=100, ms, Fixed] then the UE
sends a MEASUREMENT REPORT for event 3a to the Serving RNC and an Inter-RAT Handover commences.
Figure 21: Event 3a (EcNo)
CPICH Ec/No or
BCCH RxLev
usedFreqThresh2dEcno + utranRelThresh3aEcno
Best Cell in the Active Set
gsmThresh3a
hysteresis3a
MEASUREMENT
REPORT to RNC
GSM BCCH
timeToTrigger3a
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 64 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
If the Event 2d reported by the UE indicated the trigger occurred due to CPICH RSCP for Inter-RAT
measurements the following occurs:
 If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) Ec/No of the Best Cell in the Active
Set is less than usedFreqThresh2dRscp + utranRelThresh3aRscp [RNC, 7, dB, Fixed] – hysteresis3a [RNC, 4,
0.5dB, Fixed] / 2 and the Weighted absolute level of the GSM Broadcast Control CHannel (BCCH) is greater than
gsmThresh3a [RNC, -98, dBm, Fixed] for a time equal to timeToTrigger3a [RNC, 6=100, ms, Fixed] then the UE
sends a MEASUREMENT REPORT for event 3a to the Serving RNC and an Inter-RAT Handover commences.
Figure 22: Event 3a (RSCP)
CPICH RSCP or
BCCH RxLev
usedFreqThresh2dRscp + utranRelThresh3aRscp
Best Cell in the Active
Set
gsmThresh3a
hysteresis3a
MEASUREMENT
REPORT to RNC
GSM BCCH
timeToTrigger3a
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 65 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
If Event 6d was reported indicating the trigger occurred due to UE Transmit Power, the following occurs
for Inter-RAT measurements:
 If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) RSCP of the Best Cell in the Active
Set is less than usedFreqThresh2dRscp + utranRelThresh3aRscp [RNC, 7, dB, Fixed] + utranRelThreshRscp
[RNC, 5, dB, Fixed] – hysteresis3a [RNC, 4, 0.5dB, Fixed] / 2 and the Weighted absolute level of the GSM
Broadcast Control CHannel (BCCH) is greater than gsmThresh3a [RNC, -98, dBm, Fixed] for a time equal to
timeToTrigger3a [RNC, 6=100, ms, Fixed] then the UE sends a MEASUREMENT REPORT for event 3a to the
Serving RNC and an Inter-RAT Handover commences.
Figure 23: Event 3a (UE Tx)
CPICH RSCP or
BCCH RxLev
usedFreqThresh2dRscp + utranRelThresh3aRscp
+ utranRelThreshRscp
Best Cell in the Active
Set
gsmThresh3a
hysteresis3a
MEASUREMENT
REPORT to RNC
GSM BCCH
timeToTrigger3a
Filtering: Before Event 3a can occur, the measurements made by the UE are Filtered according to the
formula below:
Fn = (1-a) F n-1 + a M n
Where:
 Fn = The updated measurement.
 Fn-1 = the last (old) filtered measurement result.
 Mn = the Ec/No as measured by the UE.
 a = 1/2(k/2) where k is gsmFilterCoefficient3 [RNC, 1, coeff, Fixed].
Offsetting: The updated measurement (Fn) is then offset by individualOffset(UtranCell) [Cell, 0, 0.5dB,
Fixed].
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 66 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Weighting: For Event 3a, utranCoefficient3 [RNC, 2, coeff, Fixed] can be used to give heavier weight
to the serving cell while utranW3a [RNC, 10, 0.1unit, Fixed] can be used to give heavier weight to the
candidate cell.
If the Event 2d reported by the UE indicated the trigger occurred due to CPICH Ec/No for Inter-Frequency
measurements:
 If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) Ec/No of the Best Cell in the Active
Set is less than usedFreqThresh2dEcno + usedFreqRelThresh4_2bEcno [RNC, -1, dB, Fixed] – hyst4_2b
[RNC, 10, 0.1dB, Fixed] / 2 and the Waited estimated quality of the unused frequency is above both the absolute
thresholds nonUsedFreqThresh4_2bEcno [RNC, -13, dB, Fixed] + hyst4_2b [RNC, 10, 0.1dB, Fixed] / 2 and
nonUsedFreqThresh4_2bRscp [RNC, -105, dBm, Fixed] + hyst4_2b [RNC, 10, 0.1dB, Fixed] / 2, for at least
timeTrigg4_2b [RNC, 100, ms, Fixed] , then the UE sends a MEASUREMENT REPORT for event 2b to the
Serving RNC and an Inter-Frequency Handover commences.
Figure 24: Event 2b (EcNo)
CPICH Ec/No
or
CPICH RSCP
usedFreqThresh2dEcno +
usedFreqRelThresh4_2bEcno
Best Cell in the AS
'used'
nonUsedFreqThresh4_2bRscp
nonUsedFreqThresh4_2bEcno
hyst4_2b
Candidate
'non-unused'
Frequency
ND-00150
Rev. 3.0 09/09/2007
MEASUREMENT
REPORT to RNC
timeTrigg4_2b
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 67 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
If the Event 2d reported by the UE indicated the trigger occurred due to CPICH RSCP for Inter-Frequency
measurements:
 If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) RSCP of the Best Cell in the Active
Set is less than usedFreqThresh2dRscp + UsedFreqRelThresh4_2bRscp [RNC, -3, dB, Fixed] – Hyst4_2b
[RNC, 10, 0.1dB, Fixed] / 2 and the Weighted estimated quality of the unused frequency is above both the
absolute thresholds nonUsedFreqThresh4_2bEcno [RNC, -13, dB, Fixed] + hyst4_2b [RNC, 10, 0.1dB, Fixed] /
2 and nonUsedFreqThresh4_2bRscp [RNC, -105, dBm, Fixed] + hyst4_2b [RNC, 10, 0.1dB, Fixed] / 2, for at
least timeTrigg4_2b [RNC, 100, ms, Fixed] , then the UE sends a MEASUREMENT REPORT for event 2b to the
Serving RNC and an Inter-Frequency Handover commences.
Figure 25: Event 2b (RSCP)
CPICH Ec/No
or
CPICH RSCP
usedFreqThresh2dRscp +
usedFreqRelThresh4_2bRscp
Best Cell in the AS
nonUsedFreqThresh4_2bRscp
nonUsedFreqThresh4_2bEcno
hyst4_2b
Candidate
(unused)
Frequency
ND-00150
Rev. 3.0 09/09/2007
MEASUREMENT
REPORT to RNC
timeTrigg4_2b
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 68 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
If Event 6d was reported indicating the trigger occurred due to UE Transmit Power, the following occurs
for Inter-Frequency measurements:
 If the Filtered, Offset and Weighted Primary Common Pilot Channel (P-CPICH) RSCP of the Best Cell in the Active
Set is less than usedFreqThresh2dRscp + UsedFreqRelThresh4_2bRscp [RNC, -3, dB, Fixed] +
utranRelThreshRscp [RNC, 5, dB, Fixed] – hyst4_2b [RNC, 10, 0.1dB, Fixed] / 2 and the Weighted RSCP of the
unused frequency is greater than nonUsedFreqThresh4_2bRscp [RNC, -105, dBm, Fixed] + hyst4_2b [RNC, 10,
0.1dB, Fixed] / 2, for at least timeTrigg4_2b [RNC, 100, ms, Fixed] , then the UE sends a MEASUREMENT
REPORT for event 2b to the Serving RNC and an Inter-Frequency Handover commences.
Figure 26: Event 2b (UE Tx)
usedFreqThresh2dRscp +
usedFreqRelThresh4_2bRscp +
utranRelThreshRscp
CPICH RSCP
Best Cell in the AS
'used'
nonUsedFreqThresh4_2bRscp
hyst4_2b
MEASUREMENT
REPORT to RNC
Candidate
'non-used'
Frequency
timeTrigg4_2b
Filtering: Before Event 2b can occur, the measurements made by the UE are Filtered according to the
formula below:
Fn = (1-a) F n-1 + a M n
Where:
 Fn = The updated measurement.
 Fn-1 = the last (old) filtered measurement result.
 Mn = the Ec/No as measured by the UE.
 a = 1/2(k/2) where k is filterCoeff4_2b [RNC, 2, coeff, Fixed].
Offsetting: The updated measurement (Fn) is then offset by individualOffset(UtranCell) [Cell, 0, 0.5dB,
Fixed].
Weighting: For Event 2b, usedFreqW4_2b [RNC, 0, coeff, Fixed] can be used to give heavier weight to
the serving cell while nonUsedFreqW4_2b [RNC, 0, coeff, Fixed] [RNC, 0, coeff, Fixed] can be used to
give heavier weight to the candidate cell.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 69 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.5 HS Cell Change
hsQualityEstimate [RNC, 1=RSCP, Binary, Fixed] determines if whether Primary Common Pilot Channel
(P-CPICH) Ec/No or Primary Common Pilot Channel (P-CPICH) RSCP is used. Based upon this setting,
if one of the cells in the Active Set becomes greater than the Best Cell in the Active Set by hsHysteresis1d
[RNC, 10, 0.1dB, Fixed] / 2, for a time equal to hsTimeToTrigger1d [RNC, 640, ms, Fixed] , then event 1d
HS occurs. The UE then sends a MEASUREMENT REPORT message for event 1d HS to the Serving
Radio Network Controller (SRNC). If hsCellChangeAllowed [RNC, 1=TRUE, Binary, Fixed] is set to
TRUE, a Serving HS-DSCH Cell Change will occur.
Figure 27: Event 1d HS (HS Cell Change)
CPICH Ec/No or RSCP based
upon hsQualityEstimate
Another Cell in AS
Best Cell
hsHysteresis1d
MEASUREMENT
REPORT to RNC
hsTimeToTrigger1d
The configurable parameter hsToDchTrigger is used to control whether the High Speed Downlink
Shared Channel (HS-DSCH) is dropped or Down-Switched to CELL_DCH for the following cases:
 if the Intra-RNC HS Cell Change is triggered by Event 1d HS and if there are no other RNCs involved in the
Cell Change, and the Cell Change triggered by Event 1d HS fails, hsToDchTrigger(changeOfBestCellIntraRnc)
[RNC, 1=TRUE, Binary, Fixed] is checked. If it set to 1=TRUE, the UE is Down-Switched to CELL_DCH. If it is set
to 0=FALSE, the call might be dropped. If HS Multi-RAB is in use, the speech connection is also dropped.
 If the Intra-RNC Cell Change is triggered by Event 1b or 1c and there are no other RNCs involved in the Cell
Change, and the Cell Change triggered by either Event 1b or Event 1c fails,
hsToDchTrigger(servHsChangeIntraRnc) [RNC, 1=TRUE, Binary, Fixed] is checked. If it is set to 1=TRUE, the
UE is Down-Switched to CELL_DCH. If it is set to 0=FALSE, the call might be dropped. If HS Multi-RAB is in use,
the speech connection is also dropped.
 If the Inter-RNC Cell Change is triggered by Event 1b or 1c and there is another RNC involved in the Cell
Change, and the Cell Change triggered by either Event 1b or Event 1c fails,
hsToDchTrigger(servHsChangeInterRnc) [RNC, 1=TRUE, Binary, Fixed] is checked. If it is set to 1=TRUE, the
UE is Down-Switched to CELL_DCH. If it is set to 0=FALSE, the call might be dropped. If HS Multi-RAB is in use,
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 70 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
the speech connection is also dropped.
 If the Inter-RAT or Inter-Frequency Cell Change is triggered by Event 2d or Event 6f, then either Inter-RAT or
Inter-Frequency is involved. hsToDchTrigger(poorQualityDetected) [RNC, 1=TRUE, Binary, Fixed] is checked.
If it is set to 1=TRUE, the UE is Down-Switched to CELL_DCH (64/64 RAB) in order to do Compressed Mode
measurements. If it is set to 0=FALSE, the call might be dropped. In the case of HS Multi-RAB, the speech
connection is also dropped.
In order to again obtain HSDPA service, the UE must first enter Idle Mode. Throughput on both the uplink
and downlink must fall below downswitchThreshold [RNC, 0, 1kbit/s, Fixed] , for a time equal to
downswitchTimer [RNC, 100, 100ms, Fixed]. Note that CELL_FACH is not supported over the Iur
interface and is therefore not considered.
5.3.6 Channel Switching
There are basically two kinds of Channel Switching. They are called Channel Type Switching and
Channel Rate Switching.
The Channel Type Switching algorithm applies after Interactive Class Call Establishment and allows for
the most efficient use of resources by dynamically switching the User Plane data connection between the
States of URA_PCH, CELL_FACH (Common Channels), and CELL_DCH (Dedicated Channels). The
UEs are Channel Type switched based upon the volume of data being transferred. The Channel Type
Switching algorithms are:
 Throughput triggered Dedicated (DCH/DCH) to Common Down-Switch
 Throughput triggered HS (DCH/HS or EUL/HS to Common Down-Switch
 Buffer Load triggered Common to Dedicated (DCH/DCH, DCH/HS or EUL/HS) Up-Switch
 Throughput triggered Common to Idle Mode Down-Switch
 Throughput triggered Idle Mode to URA_PCH Down-Switch
The Channel Rate Switching algorithm likewise applies after Interactive Class Call Establishment to
CELL_DCH (Dedicated Channels) and allows for the most efficient use of resources by dynamically
Channel Rate Switching among the available R99 Interactive Class Radio Access Bearers (RABs). The
UEs are likewise Channel Rate switched based upon the volume of data being transferred over time. The
Channel Rate Switching algorithms are:
 Throughput triggered Dedicated to Dedicated Down-Switch (Uplink)
 Throughput triggered Dedicated to Dedicated Down-Switch (Downlink)
 Throughput triggered Dedicated to Dedicated Up-Switch (Uplink)
 Throughput triggered Dedicated to Dedicated Up-Switch (Downlink)
 Coverage triggered Dedicated to Dedicated Down-Switch (Downlink only)
 Throughput triggered Multi-RAB (Speech and Data) Dedicated to Dedicated Down-Switch
In addition to a UE being Up-Switched and Down-Switched due to User Plane data volume, a UE can be
Down-Switched for reasons of Congestion Control, Admission Control, Handover or Coverage.
 Admission Control can Down-Switch Interactive Class users to 64/64 when resources are needed for Hand-in or
Call Establishment.
 In order to support Inter-RNC and Inter-RAT HS Cell Change , UEs are down-switched to DCH/DCH. In the InterRNC case, the UE must stay on DCH/DCH on the Drift RNC until after it transitions to Idle Mode. For the Inter-
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 71 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
RAT case, the UE is down-switched to 64/64 to allow for Compressed Mode measurements of the 2G network. If
the Compressed Mode measurements do not result in Inter-RAT Cell Change, the UE will return to its former
DCH/HS or EUL/HS condition.
The Channel Type and Rate Switching algorithms base decisions upon three quantities:
 Buffer Load. Buffer load considers the size of the Radio Link Control (RLC) window and the total number of bytes
in the Service Data Unit (SDU) buffers and retransmission buffers. All Channel Type Up-Switches from either Idle
Mode or Common Channels are triggered by Buffer Load.
 Throughput. Uplink throughput is defined as the number of bits per second coming up from the Medium Access
Control (MAC) Layer to the Radio Link Control (RLC) Layer. Downlink throughput is defined as the number of bits
per second coming down from the Radio Link Control (RLC) Layer to the Medium Access Control (MAC) Layer. All
Channel Rate Up-Switches and Down-Switches between Dedicated Channels are triggered by Throughput.
 Downlink Code Power. The Downlink code power based upon the power of the pilot bits of the Dedicated
Physical Control CHannel (DPCCH).
The following sub sections define the algorithms wherein Up-Switches and Down-Switches occur.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 72 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.1
Throughput triggered Dedicated (DCH/DCH) to Common Down-Switch
While the UE is using DCH/DCH, throughput is monitored on the uplink and downlink. If the throughput
on both the uplink and downlink falls below downswitchThreshold [RNC, 0, 1kbit/s, Fixed] , for a time
equal to downswitchTimer [RNC, 100, 100ms, Fixed] , a Down-Switch to CELL_FACH occurs as
indicated below by the Red arrow. If the throughput on either the uplink or downlink increases above
downswitchTimerThreshold [RNC, 0, 1kbit/s, Fixed] before downswitchTimer [RNC, 100, 100ms,
Fixed] expires, the downswitchTimer [RNC, 100, 100ms, Fixed] is stopped and no Down-Switch is
issued.
Figure 28: Dedicated (DCH/DCH) to Common Down-Switch
downswitchThreshold
and
downswitchTimerThreshold
Throughput
Down-Switch to
Common
Channels occurs
Uplink Throughput
Downlink Throughput
downswitchTimer
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Dedicated (DCH/DCH) to
Common Down-Switch
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 73 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.2
Throughput triggered HS (DCH/HS or EUL/HS) to Common Down-Switch
While the UE is on the High Speed Downlink Shared CHannel (HS-DSCH), throughput is monitored on
the uplink and downlink. If the throughput on both the uplink and downlink is 0 kb/s for
hsdschInactivityTimer [RNC, 10, seconds, Fixed] , the UTRAN sends an Iu Release Request to the
Core Network and the UE is sent to CELL_FACH State. Any active PDP Context is maintained.
Figure 29: HS (DCH/HS or EUL/HS) to Common Down-Switch
Uplink or Downlink
Throughput
Downlink Throughput
Down-Switch to
CELL_FACH occurs
0 kb/s
Uplink Throughput
hsdschInactivityTimer
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
HS to Common DownSwitch
Page 74 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.3
Buffer Load triggered Common to Dedicated (DCH/DCH, DCH/HS or EUL/HS) Up-Switch
While the UE is in CELL_FACH, Radio Link Control (RLC) buffer loading is monitored on the uplink and
downlink. If the Radio Link Control (RLC) buffer load in the uplink exceeds ulRlcBufUpswitch [RNC,
256, bytes, Fixed] , or if the Radio Link Control (RLC) buffer load in the downlink exceeds
dlRlcBufUpswitch [RNC, 500, bytes, Fixed] , then an Up-Switch from Common Channels (CELL_FACH)
to CELL_DCH occurs (subject to Admission Control ).
Figure 30: Common to Dedicated (DCH/DCH, DCH/HS or EUL/HS) Up-Switch
Uplink or Downlink RLC Buffer
Up-Switch to
Dedicated
Channel occurs
dlRlcBufUpswitch
ulRlcBufUpswitch
Downlink RLC Buffer
Uplink RLC Buffer
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Common to Dedicated
Up-Switch
Page 75 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.4
Throughput triggered Common to URA_PCH Down-Switch
While the UE is in CELL_FACH (Common Channels), throughput is monitored on the uplink and
downlink. If the throughput on both the uplink and downlink is 0 kb/s for inactivityTimer [RNC, 10,
seconds, Fixed] , the UE is sent to URA_PCH state. Any active PDP Context is maintained.
Figure 31: Common to URA_PCH Down-Switch
Uplink or Downlink Throughput
Downlink Throughput
Down-Switch to
URA_PCH occurs
0 kb/s
Uplink Throughput
inactivityTimer
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Common to URA_PCH
Down-Switch
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 76 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.5
Throughput triggered URA_PCH to Idle Mode Down-Switch
While the UE is in URA_PCH state, throughput is monitored on the uplink and downlink. If the throughput
on both the uplink and downlink is 0 kb/s for inactivityTimerPch [RNC, 30, minutes, Fixed] , the UTRAN
sends an Iu Release Request to the Core Network and the UE is sent to Idle Mode. Any active PDP
Context is maintained.
Figure 32: URA_PCH to Idle Mode Down-Switch
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
URA_PCH to Idle Mode
Down-Switch
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 77 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.6
Throughput triggered Dedicated to Dedicated Down-Switch (Downlink)
While the UE is using DCH/DCH; with or without Speech (MultiRAB), throughput is monitored on the
downlink. If the throughput on the downlink falls below dlDownswitchBandwidthMargin [RNC, 80, %,
Fixed] , for a time equal to dlThroughputDownswitchTimer [RNC, 20, 100ms, Fixed] , a Down-Switch to
the next lower rate occurs as indicated below by the Red arrow.
Figure 33: Throughput triggered DCH to DCH Down-Switch (Downlink)
Throughput
dlDownswitchBandwidthMargin
Down-Switch
occurs
Downlink Throughput
dlThroughputDownswitchTimer
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Dedicated (DCH/DCH) to
Dedicated Down-Switch
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 78 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.7
Throughput triggered Dedicated to Dedicated Down-Switch (Uplink)
While the UE is using DCH/HS or DCH/DCH; with or without Speech (MultiRAB), throughput is monitored
on the Uplink. If the throughput on the Uplink falls below ulDownswitchBandwidthMargin [RNC, 80, %,
Fixed] , for a time equal to ulThroughputDownswitchTimer [RNC, 20, 100ms, Fixed] , a Down-Switch to
the next lower rate occurs as indicated below by the Red arrow.
Figure 34: Throughput triggered DCH to DCH Down-Switch (Uplink)
Throughput
ulDownswitchBandwidthMargin
Down-Switch
occurs
Uplink Throughput
ulThroughputDownswitchTimer
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Dedicated to Dedicated
Down-Switch
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 79 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.8
Throughput triggered Dedicated to Dedicated Up-Switch (Downlink)
While the UE is using DCH/DCH; with or without Speech (MultiRAB), the downlink throughput and
Channelization Code Power are monitored for each UE. If the downlink throughput exceeds
bandwidthMargin [RNC, 90, %, Fixed] of the current channel’s capability for an amount of time specified
by upswitchTimer [RNC, 5, 100ms, Fixed] , and the Downlink throughput has been below
dlThroughputAllowUpswitchThreshold [RNC, 0, %, Fixed] of the maximum channel bitrate, then the
downlink code power is checked on all legs in the active set to see if an Up-Switch is possible. If
dlThroughputAllowUpswitchThreshold [RNC, 0, %, Fixed] is set to 0, then it has no affect.
 The Code Power is checked using the same downswitchPwrMargin [RNC, 2, 0.5dB, Fixed] configurable
parameter used in the Coverage triggered Dedicated to Dedicated Down-Switch. If the estimated power increase
due to the Up-Switch (64 to 128 = 2.9dB, 128 to 384 = 4.7dB) is within maximumTransmissionPower [Cell, 400,
0.1dBm, Var.] – downswitchPwrMargin [RNC, 2, 0.5dB, Fixed] – upswitchPwrMargin [RNC, 6, 0.5dB, Fixed] ,
then code power is considered to be available.
Figure 35: Code Power check for Up-Switch (Downlink)
Power
downswitchPwrMargin
maximumTransmissionPower
upswitchPwrMargin
Downlink Code Power
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 80 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
If Code Power is available, then an Up-Switch is allowed to occur subject to Admission Control. When
Up-Switching from 64kb, the first attempt will be made to Up-Switch to 384kb. If this attempt fails, a
second attempt to Up-Switch to 128kb will be made.
Figure 36: Code Power check for Up-Switch (Downlink)
Throughput
Downlink
Throughput
bandwidthMargin
Up-Switch
occurs
dlThroughputAllowUpswitchThreshold
upswitchTimer
DCH / DCH
64/384
1st Attempt
64/128
2nd Attempt
64/64
EUL / HS
128/384
1st Attempt
128/128
2nd Attempt
128/64
384/384
EUL/HS
1st Attempt
384/128
DCH / HS
2nd Attempt
384/HS
384/64
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Dedicated to Dedicated
Up-Switch
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 81 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.9
Throughput triggered Dedicated to Dedicated Up-Switch (Uplink)
While the UE is using DCH/DCH or DCH/HS, throughput is monitored on the uplink. If the throughput on
the uplink increases above bandwidthMarginUl [RNC, 90, %, Fixed] of the Radio Access Bearers
capability for a time equal to upswitchTimerUl [RNC, 1, 100ms, Fixed] , and the Uplink throughput has
been below ulThroughputAllowUpswitchThreshold [RNC, 90, %, Fixed] of the maximum channel
bitrate, an Up-Switch to the next highest Radio Access Bearer (RAB) occurs as indicated below by the
Red arrows. If ulThroughputAllowUpswitchThreshold [RNC, 90, %, Fixed] is set to 0, then it has no
affect.
Figure 37: Throughput Triggered Up-Switch (Uplink)
Throughput
bandwidthMarginUl
Uplink Throughput
Up-Switch to
next highest
RAB occurs
ulThroughputAllowUpswitchThreshold
upswitchTimerUl
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Dedicated to Dedicated
Down-Switch
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 82 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.10 Coverage triggered Dedicated to Dedicated Down-Switch
Coverage, or rather the lack of coverage, may cause the downlink code power to increase to its
maximum. In this case, a Down-Switch from 64/384 to 64/128 or from 64/128 to 64/64 is preferable to
exhausting power and possibly dropping the connection. The algorithm periodically (every 1 second)
monitors downlink code power on all legs in the Active Set. If the downlink code power on all legs in the
Active Set is within downswitchPwrMargin [RNC, 2, 0.5dB, Fixed] of maximumTransmissionPower
[Cell, 400, 0.1dBm, Var.] , then coverageTimer [RNC, 10, 100ms, Fixed] is started. If the code power on
all of the legs stays above maximumTransmissionPower [Cell, 400, 0.1dBm, Var.] - reportHysteresis
[RNC, 6, 0.5dB, Fixed] before coverageTimer [RNC, 10, 100ms, Fixed] expires, the UE is DownSwitched to the next lowest Radio Access Bearer (RAB).
Figure 38: Covered Triggered Ded. to Ded. Down-Switch
Power
downswitchPwrMargin
maximumTransmissionPower
reportHysteresis
Down-Switch to
next lowest RAB
Downlink Code Power
coverageTimer
DCH / DCH
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS
384/HS
64/HS
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Dedicated (DCH/DCH) to
Dedicated Down-Switch
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 83 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.11 Throughput triggered Speech + Data Multi-RAB Down-Switch
While the UE has a DCH/HS Multi-RAB or DCH/HS Multi-RAB with Speech connection, throughput is
monitored on the uplink and downlink. If the throughput on both the uplink and downlink is 0 kb/s for
downswitchTimerSp [RNC, 2, 0.5seconds, Fixed] , the connection is Down-Switched to CS
Conversational 12.2k AMR speech and PS Interactive 0/0 data (SP0).
Figure 39: Throughput Triggered Down-Switch (Multi-RAB)
Uplink or HS Downlink
Throughput
Downlink Throughput
Down-Switch to
Idle occurs
0 kb/s
Uplink Throughput
downswitchTimerSp
DCH / DCH with Speech
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS with Speech
384/HS
64/HS
0/0 with Speech
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Down-Switch to SP0
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 84 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.12 Throughput triggered Speech + Data Multi-RAB Up-Switch
While the UE has a Multi-RAB CS Conversational 12.2k AMR speech and PS Interactive 0/0 data (SP0)
connection, the Radio Link Control (RLC) buffer load is monitored on the uplink and downlink. If the
Radio Link Control (RLC) buffer load in the uplink exceeds ulRlcBufUpswitchMrab [RNC, 8, bytes,
Fixed] or likewise if the Radio Link Control (RLC) buffer load in the downlink exceeds
dlRlcBufUpswitchMrab [RNC, 8, 100bytes, Fixed] an Up-Switch to CS Conversational 12.2k AMR
speech and PS Interactive 64/64 or 64/HS will occur subject to Admission Control.
Figure 40: Throughput Triggered Up-Switch (Multi-RAB)
Uplink or Downlink RLC Buffer Load
DL RLC Buffer Load
UL RLC Buffer Load
Up-Switch to
Multi-RAB 64/64
or 64/HS occurs
dlRlcBufUpswitchMrab
DCH / DCH with Speech
ulRlcBufUpswitchMrab
EUL / HS
64/384
128/384
384/384
64/128
128/128
384/128
64/64
128/64
384/64
EUL/HS
DCH / HS with Speech
384/HS
64/HS
0/0 with Speech
CELL_FACH
(Common)
URA_PCH
ND-00150
Rev. 3.0 09/09/2007
Idle Mode
Up-Switch from SP0
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 85 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.6.13 Throughput triggered 2xPS or Speech + 2xPS Multi-RAB Down-Switch
While the UE has two simultaneous DCH/DCH data RABs or Speech plus two simultaneous DCH/DCH
data RABs, throughput is monitored on the uplink and downlink. If the throughput on both the uplink and
downlink for one of the Data RABs is 0 kb/s for inactivityTimeMultiPsInteractive [RNC, 50, 100ms,
Fixed] , that Data RAB is released.
Figure 41: Throughput Triggered Down-Switch (2xPSMulti-RAB)
Throughput
Downlink Throughput
Data RAB is
released
0 kb/s
Uplink Throughput
inactivityTimeMultiPsInteractive
5.3.7 HSDPA Scheduling
Given all HSDPA users are Interactive / Background Class and as such have no priority over each other,
there needs to be an ability to determine how the HS-DSCH is utilized among multiple users on a cell in
order to use the resource in the most efficient manner. queueSelectAlgorithm [Cell, 3, Integer, Fixed]
controls the method used to accomplish this. The options are:
 1=ROUND_ROBIN. Users are prioritized based upon the amount of data waiting to be transmitted to them. The
longer the user has to wait, the higher their priority. There is no consideration for signal quality (CQI).
 2=PROPORTIONAL_FAIR_MEDIUM. In addition to the Round Robin method, a ‘medium’ consideration is given
to the users CQI. Because more time is given to users with better signal quality, cell throughput is improved over
both ROUND_ROBIN and PROPORTIONAL_FAIR_LOW. However, users with worse quality will not be
scheduled as often and as such will need the resource for a longer period of time.
 3=PROPORTIONAL_FAIR_LOW. In addition to the Round Robin method, a ‘low’ consideration is given to the
users CQI. Because more time is given to users with better signal quality, cell throughput is improved over
ROUND_ROBIN. However, users with worse quality will not be scheduled as often and as such will need the
resource for a longer period of time.
 4=PROPORTIONAL_FAIR_HIGH. In addition to the Round Robin method, a ‘high’ consideration is given to the
users CQI. Because more time is given to users with better signal quality, cell throughput is improved over
ROUND_ROBIN, PROPORTIONAL_FAIR_LOW and PROPORTIONAL_FAIR_MEDIUM. However, users with
worse quality will not be scheduled as often and as such will need the resource for a longer period of time.
 5=MAXIMUM_CQI. The user’s quality (CQI) is considered over how much data is waiting to be transmitted to
them. Because this option favors signal quality over everything else, cell throughput is maximized.
 6=EQUAL_RATE. This option provides equal opportunity to all users on the cell regardless of signal quality or
data waiting to be transmitted. Based upon airRateTypeSelector [Cell, 1=TRANSMITTED, Integer, Fixed] , either
Transmitted (acknowledged + unacknowledged) or Acknowledged only data can be used to determine each user’s
rate.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 86 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
5.3.8 EUL Scheduling
In the interests of getting version 3.0 of the Vol. II Field Guide published, the parameters involved in EUL
Sheduling will be defined out of context. Version 3.1 will remedy this. The following comes directly from
the CPI.
eulTargetRate [Cell, 128, 1kbit/s, Fixed]
 Defines the target scheduled grant for the cell that is the EUL scheduler aims to give all users at least
eulTargetRate kbps.
eulNoReschUsers [Cell, 5, E-DCH users, Fixed]
 Defines the number of simultaneous users per cell that are allowed to perform rescheduling.
eulMaxNoSchEdch [Cell, 16, E-DCH users, Fixed]
 Defines the maximum number of simultaneous scheduled serving E-DCH users having a scheduled data rate
larger then zero kbps.
eulNoErgchGroups [Cell, 4, E-RGCH groups, Fixed]
 Defines the number of E-RGCH groups per channelization code and cell.
eulMaxShoRate [Cell, 1472, 1kbit/s, Fixed]
 Defines the maximum rate that may be allocated in the serving cell for scheduled data to an E-DCH user during a
soft(er) handover.
eulReservedHwBandwidthSchedDatNonServCell [Cell, 128, 1kbit/s, Fixed]
 In soft handover, the non-serving cell shall reserve the hardware resources needed for this rate as well as nonscheduled data.
eulThermalLevelPrior [Cell, -1040, 0.1dBm, Fixed]
 This parameter is the assumed mean of the noise floor including feeder and TMA contribution. It describes the
mean of the prior information distribution of the noise floor. Normally the default value should be used, but in case
for example the RX-chain is wrongly configured this parameter can be set to a different value.
eulSlidingWindowTime [Cell, 1800, seconds, Fixed]
 This parameter is the length of the sliding window during which a thermal noise level is calculated.
eulMinMarginCoverage [Cell, 10, -, Fixed]
 Defines the minimum margin for the interference contribution from sources other than DCH traffic and thermal
noise (interference from other cells, sources external to the WCDMA system and so on.).
eulNoiseFloorLock [Cell, 0=FALSE, -, Fixed]
 If eulNoiseFloorLock [Cell, 0=FALSE, -, Fixed] is set to 0=FALSE, the noise floor is determined according to the
measurement algorithm. If set to 1=TRUE, eulNoiseFloorLock [Cell, 0=FALSE, -, Fixed] locks the noise floor
level. The noise floor level is locked to eulOptimalNoiseFloorEstimate [Cell, -1040, 0.1dBm, Fixed].
eulMaxRotCoverage [Cell, 100, 0.1dB, Fixed]
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 87 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 Defines the maximum RoT level that is allowed to preserve coverage (includes all uplink traffic and external
interference).
eulMaxOwnUuLoad [Cell, 80, 0.1dB, Fixed]
 Defines the maximum allowed power-controlled noise (includes power-controlled RoT including contributions from
all uplink traffic) in own cell.
harqTransmUlTti10Max
 Defines the maximum number of HARQ transmission attempts for a MAC-e PDU.
9.
Congestion Detection and Resolution
The Congestion Control algorithm has the ability to order the Admission Control algorithm to block
admission requests in order to reduce congestion. It can also Down-Switch Interactive Packet Switched
users to lower throughput Radio Access Bearers (RABs) in an effort to reduce congestion while
maintaining Retainability.
Congestion must initially be detected, then measures must be taken to resolve it. The following sections
cover the parameters used for Congestion Detection and Resolution.
1.
Congestion Detection
Congestion is detected through Downlink power utilization and Uplink Received Total Wideband Power
(RTWP) measurements obtained through the Node B. The cell is considered Congested when either of
these criteria is met.
 Downlink Congestion. When the Downlink Transmitted Carrier Power exceeds pwrAdm [Cell, 75, %, Var.] +
pwrAdmOffset [Cell, 10, %, Var.] + pwrOffset [Cell, 5, %, Fixed] of maximumTransmissionPower [Cell, 400,
0.1dBm, Var.] for a period of time greater than pwrHyst [Cell, 300, ms, Fixed] , the Downlink is considered
congested. The Congested condition is not resolved until the Downlink Transmitted Carrier Power is reduced
below pwrAdm [Cell, 75, %, Var.] + pwrAdmOffset [Cell, 10, %, Var.] of maximumTransmissionPower [Cell,
400, 0.1dBm, Var.] for a period of time greater than pwrHyst [Cell, 300, ms, Fixed].
The pwrAdm [Cell, 75, %, Var.] and pwrAdmOffset [Cell, 10, %, Var.] parameters are also used in
Admission Control.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 88 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Figure 42: Congestion Detection (Downlink)
Power
maximumTransmissionPower
pwrAdm
pwrAdmOffset
Cell is Congested
pwrOffset
Node B Carrier Power
ND-00150
Rev. 3.0 09/09/2007
pwrHyst
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 89 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 Uplink Congestion. When the Uplink Received Total Wideband Power (RTWP) exceeds iFCong [Cell, 621,
0.1dBm, Fixed] + iFOffset [Cell, 0, 0.1dB, Fixed] for a period of time greater than iFHyst [Cell, 6000, 10ms, Fixed]
, the Uplink is considered congested. The Congested condition is not resolved until the Uplink Transmitted Carrier
Power is reduced below iFCong [Cell, 621, 0.1dBm, Fixed] + iFOffset [Cell, 0, 0.1dB, Fixed] for a period of time
greater than iFHyst [Cell, 6000, 10ms, Fixed].
Figure 43: Congestion Detection (Uplink)
Recived Total Wideband
Power (RTWP)
iFOffset
iFCong
Uplink is
Congested
RTWP measured by
Node B
iFHyst
5.3.9.2
Congestion Resolution
Action is taken in the form of blocking new connections (Call Establishments and Hand-ins) and by
reducing the rate of existing Interactive Packet Switched connections. If the Congestion is due to
Downlink Power Utilization, all new connections are blocked and actions are taken to resolve the
Congestion. If the Congestion is due to Uplink Received Total Wideband Power (RTWP), only Call
Establishments are blocked as hand-ins reduce Uplink Received Total Wideband Power (RTWP).
In the case of Downlink Congestion, beyond blocking Call Establishments and Hand-ins, actions are
taken to reduce the amount of downlink power used. This is done by reducing the number of Air Speech
Equivalents served by the cell until the Congestion condition is resolved. These actions are taken in the
following order.
1. Immediately after Downlink Congested is detected, releaseAseDlNg [Cell, 3, ASE, Fixed] NonGuaranteed Air Speech Equivalents (ASEs) are released in the downlink and timers tmInitialGhs
[Cell, 500, ms, Fixed] and tmInitialG [Cell, 3000, ms, Fixed] are started. As long as the congestion
situation persists, releaseAseDlNg [Cell, 3, ASE, Fixed] Non-Guaranteed Air Speech Equivalents
(ASEs) are released every tmCongActionNg [Cell, 800, ms, Fixed].
2. If Downlink Congestion persists after all the Non-Guaranteed ASEs in downlink are released and the
timer tmInitialGhs [Cell, 500, ms, Fixed] expires, releaseAseDlGhs [Cell, 0, 0.ASE, Fixed]
Guaranteed-HS Air Speech Equivalents (ASEs) are released in the downlink. As long as the
congestion situation persists, tmCongActionGhs [Cell, 300, ms, Fixed] Guaranteed-HS Air Speech
Equivalents (ASEs) are released every releaseAseDlGhs [Cell, 0, 0.ASE, Fixed].
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 90 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
3. If Downlink Congestion persists after all Non-Guaranteed and Guaranteed-HS are released in the
downlink and the timer tmInitialG [Cell, 3000, ms, Fixed] has expired, releaseAseDl [Cell, 1, ASE,
Fixed] Guaranteed Air Speech Equivalents (ASEs) are released in the downlink. As long as the
congestion situation persists, releaseAseDl [Cell, 1, ASE, Fixed] Guaranteed Air Speech Equivalents
(ASEs) are released every tmCongAction [Cell, 2000, ms, Fixed].
5.3.10 Radio Connection Supervision
The Radio Connection for UEs in CELL_FACH, CELL_DCH and those using HSDPA is continuously
monitored in an effort to ensure the RNS has control of the UE. The following describes the parameters
that apply to each condition.
 Synchronization in CELL_FACH. When a UE enters CELL_FACH, it also starts a timer whose maximum value
is set by cchWaitCuT [RNC, 9, 5minutes, Fixed]. While in CELL_FACH, the UE sends Cell Update message
every t305 [RNC, 3=30, minutes, Fixed] minutes. Upon receiving a Cell Update CONFIRM, the UE restarts the
cchWaitCuT [RNC, 9, 5minutes, Fixed] timer. If the cchWaitCuT [RNC, 9, 5minutes, Fixed] timer expires, the
release of the connection is triggered. The cchWaitCuT [RNC, 9, 5minutes, Fixed] timer is stopped and reset to 0
if the UE enters CELL_DCH.
 Uplink Synchronization in CELL_DCH. When nOutSyncInd [Cell, 10, frames, Fixed] number of consecutive
frames are out-of-sync, a timer, rlFailureT [Cell, 10, 0.1seconds, Fixed] is started. If rlFailureT [Cell, 10,
0.1seconds, Fixed] expires, the Radio Link Set is considered out-of-sync and a Radio Link Failure is reported to
the Serving Radio Network Controller (SRNC). If while the Radio Link is out-of-sync, and nInSyncInd [Cell, 3,
frames, Fixed] number of frames are in-sync, the Radio Link is considered in-sync and a Radio Link Restore is
reported to the Serving Radio Network Controller (SRNC). The connection is considered lost if the last Radio Link
has been out-of-sync for dchRcLostT [RNC, 50, 0.1seconds, Fixed].
 Downlink Synchronization in CELL_DCH. When n313=100 number of consecutive frames are out-of-sync, a
timer t313=3s.] is started. If t313 expires, the Radio Link is considered out-of-sync and a Radio Link Failure is
reported to the Serving Radio Network Controller (SRNC). If while the Radio Link is out-of-sync, and n315=1
number of frames are in-sync, the Radio Link is considered in-sync and a Radio Link Restore is reported to the
Serving Radio Network Controller (SRNC). Note that none of the Downlink Synchronization parameters are
currently operator configurable.
 HSDPA Supervision. For UEs with HSDPA capability, hsDschRcLostT [RNC, 100, 0.1seconds, Fixed] is used.
The connection is considered lost if the Radio Link containing the High Speed Downlink Shared Channel (HSDSCH) has been out-of-sync for hsDschRcLostT [RNC, 100, 0.1seconds, Fixed].
11.
Downlink and Uplink Power Control
This section details the parameters used to control Uplink and Downlink power for CELL_FACH,
CELL_DCH and HSDPA.
1.
Maximum Forward Access CHannel (FACH) Power
The Forward Access CHannel (FACH) can carry either Control Plane or User Plane data.
 Control Plane. When the Forward Access CHannel (FACH) is used to support the Broadcast Control CHannel
(BCCH), Common Control CHannel (CCCH), or Dedicated Control Channel (DCCH), its maximum power is set
relative to the Primary Common Pilot CHannel power (PCPICH) using maxFach1Power [Cell, 18, 0.1dB, Fixed].
 User Plane. When the Forward Access CHannel (FACH) is used to support the Dedicated Traffic Channel
(DTCH), its maximum power is set relative to the Primary Common Pilot CHannel power (PCPICH) using
maxFach2Power [Cell, 15, 0.1dB, Fixed].
 Power offsets relative to the Data Field for the Transport Format Combination Indicator (TFCI) and Pilot
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 91 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Fields. pOffset1Fach [Cell, 0, 0.1dB, Fixed] for the TFCI field and pOffset3Fach [Cell, 0, 0.1dB, Fixed] for the
Pilot field take over once the initial offsets have been established by pO1 [RNC, 0, 0.25dB, Fixed] and pO3 [RNC,
12, 0.25dB, Fixed].
5.3.11.2 Downlink CELL_DCH Power Settings
There are parameters associated with maintaining upper and lower limits for power per Radio Link on the
Downlink.
 Minimum Downlink Transmitted Code Power. It is possible to set the maximum extent to which Power Control
can reduce the power of a Radio Link. The minimum downlink Transmitted Code Power is set relative to the
Primary Common Pilot CHannel (P-CPICH) power through minPwrRl [Cell, -150, 0.1dB, Fixed].
 Maximum Downlink Transmitted Code Power. When determining the Maximum Downlink Transmitted Code
Power for a Radio Link, the maximum bit rate of the Radio Link must be considered. The following table indicates
the maximum bit rate for each Radio Link supported by AT&T.
Table 15: Maximum Bit Rates per Radio Link
Radio Connection Type
Maximum Bitrates
Signaling Radio Bearer
14800
Conversational Circuit Switched Speech AMR 12.2kb
15900
Interactive Packet Switched 64kb
67700
Interactive Packet Switched 128kb
138100
Interactive Packet Switched 384kb
406900
HS for Downlink – A-DCH only
3700
The following parameters are used to determine the Maximum Downlink Transmitted Code Power for a
Radio Link based upon the Radio Link’s maximum bit rate.
 Requests for a Radio Link bit rates below minimumRate [Cell, 1590, 10bps, Fixed] are allocated a maximum
Transmitted Code Power of minPwrMax [Cell, 0, 0.1dB, Fixed] relative to the Primary Common Pilot Channel
(CPICH) power.
 Requests for a Radio Link bit rates between minimumRate [Cell, 1590, 10bps, Fixed] and interRate [Cell, 7760,
10bps, Fixed] are allocated a maximum Transmitted Code Power of interPwrMax [Cell, 38, 0.1dB, Fixed] relative
to the Primary Common Pilot Channel (CPICH) power.
 Requests for a Radio Link bit rates between interRate [Cell, 7760, 10bps, Fixed] and maxRate [Cell, 40690,
10bps, Fixed] are allocated a maximum Transmitted Code Power of maxPwrMax [Cell, 48, 0.1dB, Fixed] relative
to the Primary Common Pilot Channel (CPICH) power.
The initial downlink Dedicated Physical Data CHannel (DPDCH) power after Soft Handover is determined
using the following formula:
P_DL_DPDCH = primaryCpichPower [Cell, 300, 0.1dBm, Fixed] + (dlInitSirTarget [RNC, 41,
0.1dB, Fixed] - Ec/No_PCPICH) + cSho + 10 log(2/SF_DL_DPDCH)
Where:
 P_DL_DPDCH is the initial downlink Dedicated Physical Data CHannel (DPDCH) power at handover.
 primaryCpichPower [Cell, 300, 0.1dBm, Fixed] sets the power of the Primary Common Pilot Channel (P-CPICH)
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 92 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
sent in SIB 5.
 dlInitSirTarget [RNC, 41, 0.1dB, Fixed] sets the required initial Signal to Interference Ratio (SIR) Target.
 Ec/No_PCPICH is the ratio of Chip Energy to the Noise Power Spectral Density of the Primary Common Pilot
CHannel (P-CPICH) as measured by the UE. If this measurement is not available, ecNoPcpichDefault [RNC, 16, dB, Fixed] is used.
 cSho used to offset the value of P_DL_DPDCH by a handover margin (mSHO) and a configurable parameter
initShoPowerParam [RNC, -2, 1dB, Fixed].
 SF_DL_DPDCH is the Spreading Factor of the downlink Dedicated Physical Data CHannel (DPDCH).
The initial downlink Dedicated Physical Data CHannel (DPDCH) power after Hard Inter-Frequency
Handover is determined using the following formula:
P_DL_DPDCH = primaryCpichPower [Cell, 300, 0.1dBm, Fixed] + (dlInitSirTarget [RNC, 41,
0.1dB, Fixed] - Ec/No_PCPICH) + cNbifho [RNC, 10, 0.1dB, Fixed] + 10 log(2/SF_DL_DPDCH)
Where:
 P_DL_DPDCH is the initial downlink Dedicated Physical Data CHannel (DPDCH) power at handover.
 primaryCpichPower [Cell, 300, 0.1dBm, Fixed] sets the power of the Primary Common Pilot Channel (P-CPICH)
sent in SIB 5.
 dlInitSirTarget [RNC, 41, 0.1dB, Fixed] sets the required initial Signal to Interference Ratio (SIR) Target.
 Ec/No_PCPICH is the ratio of Chip Energy to the Noise Power Spectral Density of the Primary Common Pilot
CHannel (P-CPICH) as measured by the UE. If this measurement is not available, ecNoPcpichDefault [RNC, 16, dB, Fixed] is used.
 cNbifho [RNC, 10, 0.1dB, Fixed] is used to offset the value of P_DL_DPDCH by a taking into account the InterFrequency handover margins.
 SF_DL_DPDCH is the Spreading Factor of the downlink Dedicated Physical Data CHannel (DPDCH).
5.3.11.3 Downlink Power Balancing
Initial downlink power is achieved on the first Radio Link using the procedures and configurable parameters
covered in the Call Establishment section. Once additional Radio Links are added to the Active Set, it
becomes important to coordinate the downlink power from multiple serving cells. Keep in mind, all cells in
the Active Set listen to the same Transmit Power Control (TPC) commands from the UE. Over time, it is
possible for the cells serving the UE to transmit at significantly different power levels relative to each other.
This is known as downlink Power Drift. The following algorithm is used to manage Power Drift.
dlPcMethod [RNC, 3=BALANCING, Integer, Fixed] is used in conjunction with Inner Loop Power Control
to manage Power Drift. The options are FIXED, NO_BALANCING, BALANCING and
FIXED_BALANCING.
 1=FIXED. Both Power Balancing and downlink Inner Loop Power Control are disabled. The downlink power is
kept at a constant level of fixedPowerDl [RNC, 65, 0.5dB, Fixed].
 2=NO_BALANCING. Downlink Inner Loop Power Control is active for any number of Radio Links in the Active
Set, but Power Balancing is not.
 3=BALANCING. Power Balancing and Inner Loop Power Control are active.
 4=FIXED_BALANCING. Downlink Inner Loop Power Control is active is there is only one Radio Link in the Active
Set. Once another Radio Link is added to the Active Set, Downlink Inner Power Control is deactivated and the
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 93 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
downlink power from each serving cell converges on the power level set by fixedRefPower [RNC, 65, 0.5dB,
Fixed].
5.3.11.4 High Speed Downlink Packet Access (HSDPA) Power and Code Control
High Speed Downlink Packet Access (HSDPA) utilizes the following channels. The power and code
related parameters are presented within their respective context.
 High-Speed Shared Control Channel (HS-SCCH). This downlink channel carries hybrid-ARQ and the High
Speed Dedicated Shared CHannel (HS-DSCH) Transport Format and Resource Combination (TFRC) selection
information from the MAC-hs in the Node B to the scheduled UE. The numHsScchCodes [Cell, 3, codes, Fixed]
parameter denotes the number of High Speed Dedicated Shared CHannels (HS-DSCH) in the cell as well as the
number of HS users that can share a single TTI. If flexibleSchedulerOn [RNC, 1=TRUE, Binary, Fixed] is set to
1=TRUE, the maximum and minimum power of the High Speed Shared Control CHannel (HS-SCCH) are set
through hsScchMaxCodePower [Cell, -20, 0.5dB, Fixed] and hsScchMinCodePower [Cell, -150, 0.5dB, Fixed]
relative to the Primary Common Pilot Channel (PCPICH). The dynamic power control of the High Speed Shared
Control CHannel (HS-SCCH) is based upon measurements sent from the UE, and can be offset by
qualityCheckPower [Cell, 0, 0.5dB, Fixed] if necessary.
 High Speed Physical Downlink Shared CHannel (HS-PDSCH). The Transport Channel called the High Speed
Downlink Shared Channel (HS-DSCH) is mapped to one or more High Speed Physical Downlink Shared CHannels
(HS-PDSCH). The maximum power of each High Speed Physical Downlink Shared CHannel (HS-PDSCH) is set
to maximumTransmissionPower [Cell, 400, 0.1dBm, Var.] - hsPowerMargin [Cell, 2, 0.5dB, Fixed]. The
number of Spreading Factor 16 High Speed Physical Downlink Shared CHannels (HS-PDSCH) reserved for
HSDPA is controlled through numHsPdschCodes [Cell, 4, codes, Fixed]. If dynamicHsPdschCodeAdditionOn
[RNC, 1=TRUE, Binary, Fixed] is set to 1=TRUE, then the maximum number of Spreading Factors 16 that can be
made available for the High Speed Physical Downlink Shared CHannels (HS-PDSCH) is limited to
maxNumHsPdschCodes [Cell, 10, codes, Fixed]. If flexibleSchedulerOn [RNC, 1=TRUE, Binary, Fixed] is set
to 1=TRUE, then up to 4 users can be code multiplexed on a single 2ms TTI.
 High-Speed Dedicated Physical Control CHannel (HS-DPCCH). This uplink control channel is used by the UE
to report the measured downlink channel quality and to request the retransmission of erroneous transport blocks
on the High Speed Downlink Shared Channel (HS-DSCH). The measured downlink channel quality is reported
through use of the Channel Quality Indicator (CQI). Power is controlled on the High-Speed Dedicated Physical
Control CHannel (HS-DPCCH) relative to the Dedicated Physical Control Channel (DPCCH).
5.3.11.5 Uplink Power Control
There are two options for how Uplink Outer Loop power control is done. The algorithm is chosen using
ulOuterLoopRegulator [RNC, 1=JUMP, Integer, Fixed]. Both algorithms observe BLER on the uplink
 If ulOuterLoopRegulator [RNC, 1=JUMP, Integer, Fixed] is set to CONSTANT_STEP, and an erroneous block is
detected, the uplink SIR target is increased by ulSirStep [RNC, 10, 0.1dB, Fixed] until a number of consecutive
blocks are correctly received at which time the uplink SIR target is decreased by an equal step. The number of
consecutive blocks necessary to decrease the SIR target is dependant upon the BLER target.
 If ulOuterLoopRegulator [RNC, 1=JUMP, Integer, Fixed] is set to JUMP, and an erroneous block is detected, the
uplink SIR target is increased by ulSirStep [RNC, 10, 0.1dB, Fixed]. When a block is correctly received, the uplink
SIR target is decreased by a fraction of ulSirStep [RNC, 10, 0.1dB, Fixed]. The fraction is based upon the BLER
target.
The BLER target for both the downlink and the upink is configurable for each RAB Type and Transport
Channel (UeRcTrCh) instance. The first table below correlates the UeRc with the RAB Type and the
UeRcTrChId with the UeRcTrCh Instance. The recommended value for each RAB combination
supported by AT&T is listed below in the second table.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 94 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Table 16: UeRc, RAB and UeRcTrCh Identification
UeRc
RAB Type
UeRcTrCh Id
UeRcTrCh Instance
1
Standalone RRC on DCH
1
The only DCH
2
Speech
1
RRC Conn
2
Speech
2
Speech subflow 1
2
Speech
3
Speech subflow 2
2
Speech
4
Speech subflow 3
5
Packet 64/64
1
RRC Conn
5
Packet 64/64
2
Packet RAB
6
Packet 64/128
1
RRC Conn
6
Packet 64/128
2
Packet RAB
18
Packet 128/128
1
RRC Conn
18
Packet 128/128
2
Packet RAB
7
Packet 64/384
1
RRC Conn
7
Packet 64/384
2
Packet RAB
9
Speech + Packet 0kbps
1
RRC Conn
9
Speech + Packet 0kbps
2
Speech subflow 1
9
Speech + Packet 0kbps
3
Speech subflow 2
9
Speech + Packet 0kbps
4
Speech subflow 3
9
Speech + Packet 0kbps
5
Packet RAB
10
Speech + Packet 64kbps
1
RRC Conn
10
Speech + Packet 64kbps
2
Speech subflow 1
10
Speech + Packet 64kbps
3
Speech subflow 2
10
Speech + Packet 64kbps
4
Speech subflow 3
10
Speech + Packet 64kbps
5
Packet RAB
11
Pre-configured RRC only
1
The only DCH
12
Pre-configured Speech
1
RRC Conn
12
Pre-configured Speech
2
Speech subflow 1
12
Pre-configured Speech
3
Speech subflow 2
12
Pre-configured Speech
4
Speech subflow 3
15
PS Interactive 64/HS - HS-DSCH
1
RRC connection
15
PS Interactive 64/HS - HS-DSCH
2
PS Interactive on A-DCH
16
PS Interactive 384/HS - HS-DSCH
1
RRC connection
16
PS Interactive 384/HS - HS-DSCH
2
PS Interactive on A-DCH
19
Speech+PS Interactive 64/HS
1
RRC Conn
19
Speech+PS Interactive 64/HS
2
PS Interactive on A-DCH
19
Speech+PS Interactive 64/HS
3
Speech subflow 1
19
Speech+PS Interactive 64/HS
4
Speech subflow 2
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 95 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
UeRc
RAB Type
UeRcTrCh Id
UeRcTrCh Instance
19
Speech+PS Interactive 64/HS
5
Speech subflow 3
20
Speech+PS Interactive 384/HS
1
RRC Conn
20
Speech+PS Interactive 384/HS
2
PS Interactive on A-DCH
20
Speech+PS Interactive 384/HS
3
Speech subflow 1
20
Speech+PS Interactive 384/HS
4
Speech subflow 2
20
Speech+PS Interactive 384/HS
5
Speech subflow 3
The table below provides the recommended values for the uplink and downlink for each RAB combination
defined in the table above. The first integer in parenthesis indicates the UeRc, the second integer indicates
the UeRcTrCh Id. The values are in 10Log10(BLER quality target), for example if the desired BLER quality
target is 1%, then blerQualityTarget = 10Log10(0.01) which results in a value of -20.
Table 17: blerQualityTarget values
blerQualityTargetDl (UeRc,UeRcTrCh)
blerQualityTargetUl (UeRc,UeRcTrCh)
(1,1) [RNC, -20, 10 Log10(BLER), Fixed]
(1,1) [RNC, -20, 10 Log10(BLER), Fixed]
(2,1) [RNC, -20, 10 Log10(BLER), Fixed]
(2,1) [RNC, -20, 10 Log10(BLER), Fixed]
(2,2) [RNC, -20, 10 Log10(BLER), Fixed]
(2,2) [RNC, -20, 10 Log10(BLER), Fixed]
(2,3) [RNC, -20, 10 Log10(BLER), Fixed]
(2,3) [RNC, -20, 10 Log10(BLER), Fixed]
(2,4) [RNC, -20, 10 Log10(BLER), Fixed]
(2,4) [RNC, -20, 10 Log10(BLER), Fixed]
(5,1) [RNC, -20, 10 Log10(BLER), Fixed]
(5,1) [RNC, -20, 10 Log10(BLER), Fixed]
(5,2) [RNC, -20, 10 Log10(BLER), Fixed]
(5,2) [RNC, -20, 10 Log10(BLER), Fixed]
(6,1) [RNC, -20, 10 Log10(BLER), Fixed]
(6,1) [RNC, -20, 10 Log10(BLER), Fixed]
(6,2) [RNC, -20, 10 Log10(BLER), Fixed]
(6,2) [RNC, -20, 10 Log10(BLER), Fixed]
(18,1) [RNC, -20, 10 Log10(BLER), Fixed]
(18,1) [RNC, -20, 10 Log10(BLER), Fixed]
(18,2) [RNC, -20, 10 Log10(BLER), Fixed]
(18,2) [RNC, -20, 10 Log10(BLER), Fixed]
(7,1) [RNC, -20, 10 Log10(BLER), Fixed]
(7,1) [RNC, -20, 10 Log10(BLER), Fixed]
(7,2) [RNC, -20, 10 Log10(BLER), Fixed]
(7,2) [RNC, -20, 10 Log10(BLER), Fixed]
(9,1) [RNC, -20, 10 Log10(BLER), Fixed]
(9,1) [RNC, -20, 10 Log10(BLER), Fixed]
(9,2) [RNC, -20, 10 Log10(BLER), Fixed]
(9,2) [RNC, -20, 10 Log10(BLER), Fixed]
(9,3) [RNC, -20, 10 Log10(BLER), Fixed]
(9,3) [RNC, -20, 10 Log10(BLER), Fixed]
(9,4) [RNC, -20, 10 Log10(BLER), Fixed]
(9,4) [RNC, -20, 10 Log10(BLER), Fixed]
(9,5) [RNC, -20, 10 Log10(BLER), Fixed]
(9,5) [RNC, -20, 10 Log10(BLER), Fixed]
(10,1) [RNC, -20, 10 Log10(BLER), Fixed]
(10,1) [RNC, -20, 10 Log10(BLER), Fixed]
(10,2) [RNC, -20, 10 Log10(BLER), Fixed]
(10,2) [RNC, -20, 10 Log10(BLER), Fixed]
(10,3) [RNC, -20, 10 Log10(BLER), Fixed]
(10,3) [RNC, -20, 10 Log10(BLER), Fixed]
(10,4) [RNC, -20, 10 Log10(BLER), Fixed]
(10,4) [RNC, -20, 10 Log10(BLER), Fixed]
(10,5) [RNC, -20, 10 Log10(BLER), Fixed]
(10,5) [RNC, -20, 10 Log10(BLER), Fixed]
(11,1) [RNC, -20, 10 Log10(BLER), Fixed]
(11,1) [RNC, -20, 10 Log10(BLER), Fixed]
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 96 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
blerQualityTargetDl (UeRc,UeRcTrCh)
blerQualityTargetUl (UeRc,UeRcTrCh)
(12,1) [RNC, -20, 10 Log10(BLER), Fixed]
(12,1) [RNC, -20, 10 Log10(BLER), Fixed]
(12,2) [RNC, -20, 10 Log10(BLER), Fixed]
(12,2) [RNC, -20, 10 Log10(BLER), Fixed]
(12,3) [RNC, -20, 10 Log10(BLER), Fixed]
(12,3) [RNC, -20, 10 Log10(BLER), Fixed]
(12,4) [RNC, -20, 10 Log10(BLER), Fixed]
(12,4) [RNC, -20, 10 Log10(BLER), Fixed]
(15,1) [RNC, -30, 10 Log10(BLER), Fixed]
(15,1) [RNC, -20, 10 Log10(BLER), Fixed]
(15,2) [RNC, -20, 10 Log10(BLER), Fixed]
(15,2) [RNC, -20, 10 Log10(BLER), Fixed]
(16,1) [RNC, -30, 10 Log10(BLER), Fixed]
(16,1) [RNC, -20, 10 Log10(BLER), Fixed]
(16,2) [RNC, -20, 10 Log10(BLER), Fixed]
(16,2) [RNC, -20, 10 Log10(BLER), Fixed]
(19,1) [RNC, -30, 10 Log10(BLER), Fixed]
(19,1) [RNC, -20, 10 Log10(BLER), Fixed]
(19,2) [RNC, -20, 10 Log10(BLER), Fixed]
(19,2) [RNC, -20, 10 Log10(BLER), Fixed]
(19,3) [RNC, -20, 10 Log10(BLER), Fixed]
(19,3) [RNC, -20, 10 Log10(BLER), Fixed]
(19,4) [RNC, -20, 10 Log10(BLER), Fixed]
(19,4) [RNC, -20, 10 Log10(BLER), Fixed]
(19,5) [RNC, -20, 10 Log10(BLER), Fixed]
(19,5) [RNC, -20, 10 Log10(BLER), Fixed]
(20,1) [RNC, -30, 10 Log10(BLER), Fixed]
(20,1) [RNC, -20, 10 Log10(BLER), Fixed]
(20,2) [RNC, -20, 10 Log10(BLER), Fixed]
(20,2) [RNC, -20, 10 Log10(BLER), Fixed]
(20,3) [RNC, -20, 10 Log10(BLER), Fixed]
(20,3) [RNC, -20, 10 Log10(BLER), Fixed]
(20,4) [RNC, -20, 10 Log10(BLER), Fixed]
(20,4) [RNC, -20, 10 Log10(BLER), Fixed]
(20,5) [RNC, -20, 10 Log10(BLER), Fixed]
(20,5) [RNC, -20, 10 Log10(BLER), Fixed]
5.3.11.6 EUL Related Power Control
maxUserEhichErgchPowerDl
 Determines the maximum power level transmitted on the E-HICH and E-RGCH channels. Set relative to the
primaryCpichPower [Cell, 300, 0.1dBm, Fixed].
maxEagchPowerDl
 Determines the maximum power level transmitted on the E-AGCH channel. Set relative to the
primaryCpichPower [Cell, 300, 0.1dBm, Fixed].
transmissionTargetError
 Wanted percentage of E-DCH frames for which the actual number of Harq transmissions is greater than the target
number of Harq transmissions.
ulInitSirTargetEdch
 Initial Uplink SIR Target for RABs using E-DCH.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 97 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
6. OSS Overview
Someone new to either UTRAN in general or Ericsson’s implementation of UTRAN must first understand
the availability of OSS-RC related services, i.e. fault, performance and configuration management of the
Radio and Core networks. Given the proper understanding and access, the engineer can then measure
performance and optimize configuration based upon the recommendations given throughout this
document.
The proceedures outlined in this seciton are based upon Ericsson OSS-RC release R4.
Figure 1 below depicts the UTRAN with its various links including links to the OSS. User access to the
OSS is made available through a Citrix server.
Figure 44: OSS Connectivity
Core Network
Prospect Client/Web
Prospect
Citrix Server
OSS-RC
RNC
RNC
Citrix Client
Business
Objects
Client
RXI
NodeB
User Equipment
User Equipment
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 98 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
6.1
Configuration Management
There are various methods by which Ericsson UTRAN configurable parameters can be viewed and
updated. This section explains the procedures that must be followed in order to obtain the necessary
network access and credentials (username and password).
Network element addition / deletion procedures are not included in this document.
6.1.1 Configuration Access Procedures
The access process varies from region to region. Each region’s process is outlined below. Once
credentials are obtained, the user must install a Citrix ICA client on their local machine or laptop. The
software can be obtained by going to http://www.citrix.com. Once installed, use the “Add ICA
Connection” wizard to add a connection to one of your region’s Citrix Servers.
Table 18: Configuration Management Access Procedures
Region
Central
Northeast
West
Southeast
Process
Citrix Server IP
Go to https://nslogins.edc.cingular.net/ and click on “E” for the
“Ericsson UMTS OSS Lcye1ms”. Answer the questions that
follow.
ICA 1 - 10.175.144.68
Contact Dan Padowski with the Northeast Region OSS Team.
Send your CUID along with a list of markets to which you need
access.
ICA 1 - 10.189.19.9
Go to https://wnsuam.wnsnet.attws.com then click on “Request
Access” and provide the appropriate information to request
access to the Western Region Ericsson UMTS OSS – E7.
ICA 1 - 166.174.241.254
Go to https://nslogins.edc.cingular.net/login.cfm and enter your
appropriate domain username and password. Click on “Login
Request Form”, then answer the questions that follow.
OSS 1
ICA 2 - 10.175.144.71
ICA 2 - 10.189.19.11
ICA 2 - 155.174.242.1
ICA 1 - 10.184.18.71
ICA 2 - 10.184.18.72
OSS 2
ICA 1 - 10.184.18.141
ICA 2 - 10.184.18.142
6.1.2 Configuration Methods
There are three main methods used to control the configuration of the UTRAN
 Export configuration data then import configuration changes through the OSS. This is the preferred method
for bulk changes. An externally prepared configuration (Bulk CM file) is transferred to the OSS then imported into
a “Planned Area”. When the Planned Area is activated, the RNC and/or Node B configuration are updated. The
tool used is called the “WCDMA RAN Explorer” and is accessed by right clicking on the OSS desktop and
selecting Configuration, WCDMA radio access network, then WCDMA RAN explorer.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 99 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 Enter configuration changes via the OSS Graphical User Interface (GUI). This is the Ericsson preferred
method. First, a “Planned Area” is created, changes are made to it using the Graphical User Interface, then the
Planned Area is activated and the RNC and/or Node B configuration are updated, i.e. the Planned Area becomes
the Valid Area. The tool used is called the “WCDMA RAN Explorer” and is accessed by right clicking on the
desktop and selecting Configuration, WCDMA radio access network, then WCDMA RAN explorer.
 Make configuration changes in the UTRAN via a ChangeAll script. A ChangeAll script is written using a
specific format in a text file (ChangeAll.txt). The script is then executed as a task in the Job Manager application.
ChangeAll allows the user to make global parameter changes to specific network elements.
 Use EMAS (Element Manager Software). EMAS exists on each network element (Node B, RNC, RXI) and
allows the user to directly view and change the individual network element’s configuration. EMAS is typically not
used to change parameters that affect multiple network elements e.g. neighbor lists. EMAS uses a web client from
either the OSS via Citrix, or from your laptop assuming you are not blocked by any firewalls.
The Ericsson OSS for UMTS does not support an operator available command line interface.
6.2
Performance Management
There are currently three options available that can be used to access performance data.
 Business Objects. Business Objects is a third party application supported by Ericsson that can be used to query
the OSS performance reporting database. Business Object can be used on the OSS via a Citrix client or by using
a Business Object client installed on your laptop. See the Business Objects access procedure below for access
instructions.
 Prospect. This performance reporting platform is also known as Watchmark which was purchased by Vallent.
Web browser and laptop client options are available. See the Prospect Access procedure below for access
instructions.
 Tektronix Probes. Probes have been installed on every interface from end to end in the network. Statistical data
is sent to the Prospect database for KPI creation. The Tektronix Probe solution also has its own reporting
interface accessible via a Citrix client. See the Tektronix Probe Access procedure below for access instructions.
1.
Performance Access Procedures
This section provides information concerning how one goes about obtaining access and credentials to the
various Performance Reporting systems.
1.
Business Object Access
Business Objects access and credentials can be obtained at the same time you request access to the OSS.
The Business Objects client software and installation instructions are available at
http://ossweb.sc.attws.com/NWS/. A “bomain.key” file is required in order to access the Business Objects
server.
2.
Prospect Access
The Prospect Performance reporting system is nationally based.
 The Prospect client software and installation instructions are available at
http://ossweb.sc.attws.com/PES/APPS/Prospect/.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 100 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 Credentials can be obtained by going to http://dataops.sc.attws.com/OSS/Account/Request.htm. Click on “P” for
Prospect.
 The web interface is accessible via http://alnpspctweb03.wnsnet.attws.com:8080/pweb/login.jsp
6.2.1.3
Tektronix Probe Access
The Tektronix Probe reporting system is nationally based.
 Credentials can be obtained by going to
http://ns.cingular.net/sites/nis/operations_support_systems/account_request_hub.aspx. Click on “G” for
GeoProbe.
 The Citrix interface is accessible via 10.36.12.106. User Documentation can be found here
http://nebot.wnsnet.attws.com/docs/nis/geoprobe/quickstart.htm.
6.2.2 Ericsson Counter Types
Ericsson has seven different types of counters. Each type is designated based upon how each counter is
created.
 Peg Counter. A Peg Counter is simply incremented by 1 at each occurrence of a specific event. All Peg
Counters begin with pm…
 Gauge Counter. A Gauge Counter can be increased or decreased depending upon the activity in the system. All
Gauge Counters begin with pm…
 Accumulator. An Accumulator Counter is increased by the value of a sample. The result is the sum of the values
of the samples taken over the sample interval. Accumulator counters always begin with pmSum… or
pmSumOfSamp…
 Scan Counter. A Scan Counter is incremented by 1 each time a specific condition exists when scanned. Scans
for the condition occur at regular intervals. In most cases a separate counter exists that counts the number of
scans. All Scan Counters begin with pmSamples…
 Probability Density Function (PDF). These types of counters result from periodically reading the value of a
quantity. The value is then used to increment a corresponding counter. The counters are arranged in bins that
represent segments of the range of possible values. All Probability Density Function counters begin with pm…
 Discrete Distributed Measurement (DDM). Discrete Distributed Measurements are a series of values recorded
during a reporting period. At the end of the reporting period, each discrete measurement is recorded. All Discrete
Distributed Measurements begin with pm…
 Calculated Statistics. A Calculated Statistic results from a calculation made in the database. The counters that
contribute to the calculated value may or may not exist by themselves. All Calculated Statistics begin with cm…
Counters can also be grouped based upon where they are created.
 RNC Counters
 Node B Counters
 RXI Counters
 OSS-RC Counters. These include only Calculated Statistics.
6.2.3 Call Trace Capability
Ericsson supports three different types of call trace called UETR, CTR and GPEH. Each is briefly
described below. Each is launched from the Performance menu in the OSS Network Explorer.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 101 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 UETR. The User Equipment Traffic Recording capability allows for up to 16 specified UEs to be concurrently
traced on a single RNC. The individual UEs are specified by IMSI. One or more event or measurement messages
within one or more of the following protocol groups can be recorded: NBAP, RANAP, RNSAP and RRC.
Although only one UE can be traced per UETR session, up to 16 concurrent sessions can be run on a
single RNC.
 CTR. Cell Traffic Recording allows for the collection of one or more NBAP, RANAP, RNSAP or RRC event or
measurement messages from the first 16 UEs that request an RRC Connection setup on the specified cell. Up to
2 CTR recordings can be run concurrently.
 GPEH. The General Performance and Event Handling capability records internal node and inter-node events as
defined in a GPEH subscription profile.
3.
Fault Management
Fault Management allows for the identification of network elements that are currently, or have recently
been in a compromised condition due to a hardware or software failure. Ericsson provides tools that
allow the user to view network elements currently in fault. A fault history is also available for each
network element.
1.
Alarm Status Matrix
The Alarm Status Matrix provides a graphical overview of the fault status of network elements. The status
of the network element is indicated by its color. The Alarm List Viewer is available via the OSS by right
clicking on the desktop, then Alarm, View Alarms, Alarm Status Matrix. After running Alarm Status Matrix,
you must select a group of Managed Objects by clicking on File, then Managed Objects and selecting the
appropriate network element. The Alarm Status Matrix is typically the starting point for determining the
status of the network.
2.
Alarm List Viewer
The Alarm List Viewer is available via the OSS by right clicking on the desktop, then Alarm, View Alarms,
Alarm List Viewer. Current alarms for a network element or group of network elements can be viewed by
clicking on File, then Managed Objects and selecting the appropriate network element.
3.
Alarm Log Browser
Running the Alarm Log Browser starts an alarm search wizard that allows the user to input variables such
as date / time range and network element selection. It also allows for result filtering and sorting. The
result can provide a historical view of the faults of a particular network element.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 102 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
7. Counter and Recording Activation
1.
Counter Activation
In order for counter values to be placed in the OSS-RC database, they must be activated for collection.
There are limitations for the number of counters that may be activated concurrently.
–
RNC – 750,000 counters
–
Node B – 10,000 counters
–
RXI – 50,000 counters
An alarm is triggered if the maximum number of counters is exceeded.
7.1.1 Table Definitions
The table below contains all of the operator available Ericsson UTRAN counters and an indication of
whether or not each should be activated. The columns are explained as follows.
 Column A indicates the Managed Object (MO) to which each Counter belongs.
 Column B indicates the “Level” for each Counter, e.g. “Site”, “Cell”, “Transport”, ect. Note that the “Cell” based
counters are gathered at the RNC due to most of them being attributed to the Best Cell in the Active Set.
 Column C indicates the Counter name.
 Column D indicates whether the counter should be activated or not. If the counter should be activated, the field
indicates the Scanner Name. See the Implementation section below for suggested Scanner Names.
 Column E provides a reason for the counter’s activation, e.g. “Level 1 Scorecard”, “Dimensioning”, etc.
There is also a companion Excel spreadsheet. The “Counters” sheet contains all of the operator available
Ericsson UTRAN counters The “Revision Notes” sheet contains details concerning how and why each
counter was activated.
2.
Subscription Profiles
A Data Collection Subscription Profile, also known as a “Statistics Profile” or a “Scanner” defines specific
counters activated within one or more Radio Network Controller (RNC) served by an OSS. There are two
predefined RNC based Scanners called the “Primary Scanner” and the “Secondary Scanner” and a
predefined Site based Scanner.
You may at your discretion, choose to define User Defined Scanners per OSS or per Market.
1.
Define UD Scanners per OSS
 Pro: Easier to work with, simpler to standardize.
 Pro: Allows for fewer Scanners.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 103 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
 Con: Sites can only be added to a profile if all the selected sites have IP connectivity. This is difficult to achieve
since there almost always a site that has connection issues.
Example UD Scanner names:
 National_RNC_P5MD
 National_URel_P5MD
 National_Site_P5MD
 National_RXI_P5MD
7.1.2.2
Defining UD Scanners per Market
 Pros: Easier to add new sites to a Scanner since site failures in other RNCs will only affect those Scanners.
 Con: More difficult to manage.
Example UD Scanner names:
 National_RNC_P5MD - keep all RNCs grouped
 National_URel_P5MD - keep all URel grouped
 National_RXI_P5MD - keep all RXI grouped
 National_AtlaSite_P5MD
 National_MargSite_P5MD
 National_PrrnSite_P5MD
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 104 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Table 19: Counter Activation
MO Class
Resolution
Counter
Active within scanner
Aal0TpVccTp
Transport - RNC
pmBwErrBlocks
No
Aal0TpVccTp
Transport - RNC
pmBwLostCells
No
Aal0TpVccTp
Transport - RNC
pmBwMissinsCells
No
Aal0TpVccTp
Transport - RNC
pmFwErrBlocks
No
Aal0TpVccTp
Transport - RNC
pmFwLostCells
National_RNC_P5MD
Aal0TpVccTp
Transport - RNC
pmFwMissinsCells
No
Aal0TpVccTp
Transport - RNC
pmLostBrCells
National_RNC_P5MD
Troubleshooting
Aal0TpVccTp
Transport - RNC
pmLostFpmCells
National_RNC_P5MD
Troubleshooting
Aal1TpVccTp
Transport
pmBwErrBlocks
No
Aal1TpVccTp
Transport
pmBwLostCells
No
Aal1TpVccTp
Transport
pmBwMissinsCells
No
Aal1TpVccTp
Transport
pmFwErrBlocks
No
Aal1TpVccTp
Transport
pmFwLostCells
No
Aal1TpVccTp
Transport
pmFwMissinsCells
No
Aal1TpVccTp
Transport
pmLostBrCells
No
Aal1TpVccTp
Transport
pmLostFpmCells
No
Aal2Ap
Transport - RNC
pmExisOrigConns
No
Aal2Ap
Transport - RNC
pmExisTermConns
No
Aal2Ap
Transport - RNC
pmExisTransConns
No
Aal2Ap
Transport - RNC
pmNrOfRemotelyBlockedAal2Path
No
Aal2Ap
Transport - RNC
pmSuccInConnsRemote
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmSuccInConnsRemoteQosClassA
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmSuccInConnsRemoteQosClassB
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmSuccInConnsRemoteQosClassC
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmSuccInConnsRemoteQosClassD
No
Aal2Ap
Transport - RNC
pmSuccOutConnsRemote
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmSuccOutConnsRemoteQosClassA
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmSuccOutConnsRemoteQosClassB
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmSuccOutConnsRemoteQosClassC
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmSuccOutConnsRemoteQosClassD
No
Aal2Ap
Transport - RNC
pmUnRecMessages
No
Aal2Ap
Transport - RNC
pmUnRecParams
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 105 of 170
© 2007 AT&T
Reason
Troubleshooting
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
Aal2Ap
Transport - RNC
pmUnSuccInConnsLocalQosClassA
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccInConnsLocalQosClassB
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccInConnsLocalQosClassC
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccInConnsLocalQosClassD
No
Aal2Ap
Transport - RNC
pmUnSuccInConnsRemoteQosClassA
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccInConnsRemoteQosClassB
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccInConnsRemoteQosClassC
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccInConnsRemoteQosClassD
No
Aal2Ap
Transport - RNC
pmUnSuccOutConnsLocalQosClassA
No
Aal2Ap
Transport - RNC
pmUnSuccOutConnsLocalQosClassB
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccOutConnsLocalQosClassC
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccOutConnsLocalQosClassD
No
Aal2Ap
Transport - RNC
pmUnSuccOutConnsRemoteQosClassA
No
Aal2Ap
Transport - RNC
pmUnSuccOutConnsRemoteQosClassB
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccOutConnsRemoteQosClassC
National_RNC_P5MD
Troubleshooting
Aal2Ap
Transport - RNC
pmUnSuccOutConnsRemoteQosClassD
No
Aal2PathVccTp
Transport - RNC
pmBwErrBlocks
No
Aal2PathVccTp
Transport - RNC
pmBwLostCells
No
Aal2PathVccTp
Transport - RNC
pmBwMissinsCells
No
Aal2PathVccTp
Transport - RNC
pmDiscardedEgressCpsPackets
No
Aal2PathVccTp
Transport - RNC
pmEgressCpsPackets
No
Aal2PathVccTp
Transport - RNC
pmFwErrBlocks
No
Aal2PathVccTp
Transport - RNC
pmFwLostCells
National_RNC_P5MD
Aal2PathVccTp
Transport - RNC
pmFwMissinsCells
No
Aal2PathVccTp
Transport - RNC
pmIngressCpsPackets
No
Aal2PathVccTp
Transport - RNC
pmLostBrCells
National_RNC_P5MD
Troubleshooting
Aal2PathVccTp
Transport - RNC
pmLostFpmCells
National_RNC_P5MD
Troubleshooting
Aal2Sp
Transport - RNC
pmUnsuccessfulConnsInternal
No
Aal5TpVccTp
Transport - RNC
pmBwErrBlocks
No
Aal5TpVccTp
Transport - RNC
pmBwLostCells
No
Aal5TpVccTp
Transport - RNC
pmBwMissinsCells
No
Aal5TpVccTp
Transport - RNC
pmFwErrBlocks
No
Aal5TpVccTp
Transport - RNC
pmFwLostCells
National_RNC_P5MD
Aal5TpVccTp
Transport - RNC
pmFwMissinsCells
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 106 of 170
© 2007 AT&T
Troubleshooting
Troubleshooting
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
Aal5TpVccTp
Transport - RNC
pmLostBrCells
National_RNC_P5MD
Troubleshooting
Aal5TpVccTp
Transport - RNC
pmLostFpmCells
National_RNC_P5MD
Troubleshooting
AgpsPositioning
RNC
pmPositioningReqAttAgps
No
Add when AGPS is GA
AgpsPositioning
RNC
pmPositioningReqAttEsAgps
No
Add when AGPS is GA
AgpsPositioning
RNC
pmPositioningReqSuccAgps
No
Add when AGPS is GA
AgpsPositioning
RNC
pmPositioningReqSuccAgpsQosSucc
No
Add when AGPS is GA
AgpsPositioning
RNC
pmPositioningReqSuccEsAgps
No
Add when AGPS is GA
AgpsPositioning
RNC
pmPositioningReqSuccEsAgpsQosSucc
No
Add when AGPS is GA
AgpsPositioning
RNC
pmPositioningReqUnsuccAgpsAbort
No
Add when AGPS is GA
Aich
Site
pmNegativeMessages
National_Site_P5MD
Troubleshooting
Aich
Site
pmPositiveMessages
National_Site_P5MD
Troubleshooting
AntennaBranch
Site
pmNoOfPowLimSlots
Troubleshooting
AtmPort
Transport - RNC/Site
pmReceivedAtmCells
AtmPort
Transport - RNC/Site
pmSecondsWithUnexp
AtmPort
Transport - RNC/Site
pmTransmittedAtmCells
Carrier
Site
pmAverageRssi
National_Site_P5MD
National_RNC_P5MD/National_
Site_P5MD
No
National_RNC_P5MD/National_
Site_P5MD
RBS Primary
Carrier
Site
pmTransmittedCarrierPower
RBS Primary
PREDEF.PRIMARYSTATS - Dimensioning
CcDevice
RNC
pmSamplesMeasuredCcSpLoad
Secondary Scanner
Secondary Scanner
CcDevice
RNC
pmSumMeasuredCcSpLoad
Secondary Scanner
Secondary Scanner
CchFrameSynch
RNC
pmNoCchDiscardedDataFramesE
No
CchFrameSynch
RNC
pmNoCchDiscardedDataFramesL
No
CchFrameSynch
RNC
pmNoCchTimingAdjContrFrames
No
DcDevice
RNC
pmSamplesMeasuredDcSpLoad
Secondary Scanner
Secondary Scanner
DcDevice
RNC
pmSumMeasuredDcSpLoad
Secondary Scanner
Secondary Scanner
DchFrameSynch
RNC
pmNoDchDlTimingAdjContrFrames
No
DchFrameSynch
RNC
pmNoDchUlDataFramesOutsideWindow
No
DchFrameSynch
RNC
pmNoDlDchDiscardedDataFramesE
No
DchFrameSynch
RNC
pmNoDlDchDiscardedDataFramesL
No
DchFrameSynch
RNC
pmNoUlDchDiscardedDataFramesE
No
DchFrameSynch
RNC
pmNoUlDchDiscardedDataFramesL
No
DownlinkBaseBandPool
Site
pmApomcOfMdlr
No
DownlinkBaseBandPool
Site
pmApomcOfMdsr
No
DownlinkBaseBandPool
Site
pmApomcOfSpreadersUsed
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 107 of 170
© 2007 AT&T
Dimensioning
Dimensioning
PREDEF.PRIMARY.STATS
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
DownlinkBaseBandPool
Site
pmNoOfRadioLinksSf128
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRadioLinksSf16
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRadioLinksSf256
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRadioLinksSf32
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRadioLinksSf4
No
Sf4 not supported in the Downlink
DownlinkBaseBandPool
Site
pmNoOfRadioLinksSf64
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRadioLinksSf8
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRlAdditionFailuresSf128
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRlAdditionFailuresSf16
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRlAdditionFailuresSf256
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRlAdditionFailuresSf32
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRlAdditionFailuresSf4
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRlAdditionFailuresSf64
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmNoOfRlAdditionFailuresSf8
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupAttemptsSf128
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupAttemptsSf16
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupAttemptsSf256
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupAttemptsSf32
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupAttemptsSf4
No
Sf4 not supported in the Downlink
DownlinkBaseBandPool
Site
pmSetupAttemptsSf64
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupAttemptsSf8
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupFailuresSf128
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupFailuresSf16
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupFailuresSf256
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupFailuresSf32
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupFailuresSf4
No
Sf4 not supported in the Downlink
DownlinkBaseBandPool
Site
pmSetupFailuresSf64
National_Site_P5MD
Dimensioning
DownlinkBaseBandPool
Site
pmSetupFailuresSf8
National_Site_P5MD
Dimensioning
E1PhysPathTerm
Transport
pmEs
No
E1PhysPathTerm
Transport
pmSes
No
E1PhysPathTerm
Transport
pmUas
No
E1Ttp
Transport
pmEs
No
E1Ttp
Transport
pmSes
No
E1Ttp
Transport
pmUas
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 108 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
E3PhysPathTerm
Transport
pmEs
No
E3PhysPathTerm
Transport
pmSes
No
E3PhysPathTerm
Transport
pmUas
No
EDchResources
Site
pmCommonChPowerEul
National_Site_P5MD
Dimensioning
EDchResources
Site
pmNoActive10msFramesEul
National_Site_P5MD
Dimensioning
EDchResources
Site
pmNoAllowedEul
National_Site_P5MD
Dimensioning
EDchResources
Site
pmNoiseFloor
National_Site_P5MD
Dimensioning
EDchResources
Site
pmNoSchEdchEul
National_Site_P5MD
Dimensioning
EDchResources
Site
pmNoUlUuLoadLimitEul
National_Site_P5MD
Dimensioning
EDchResources
Site
pmOwnUuLoad
National_Site_P5MD
Dimensioning
EDchResources
Site
pmSumAckedBitsCellEul
National_Site_P5MD
Troubleshooting
EDchResources
Site
pmSumNackedBitsCellEul
National_Site_P5MD
Troubleshooting
EDchResources
Site
pmTotalRotCoverage
National_Site_P5MD
Dimensioning
EDchResources
Site
pmTotRateGrantedEul
National_Site_P5MD
Dimensioning
EDchResources
Site
pmWaitingTimeEul
National_Site_P5MD
Dimensioning
EthernetLink
Transport
pmNoOfIfInDiscards
No
EthernetLink
Transport
pmNoOfIfInErrors
No
EthernetLink
Transport
pmNoOfIfInNUcastPkts
No
EthernetLink
Transport
pmNoOfIfInUcastPkts
No
EthernetLink
Transport
pmNoOfifOutDiscards
No
EthernetLink
Transport
pmNoOfIfOutNUcastPkts
No
EthernetLink
Transport
pmNoOfIfOutUcastPkts
No
Eul
RNC
pmEulDowntimeAuto
National_Site_P5MD
Troubleshooting
Eul
RNC
pmEulDowntimeMan
National_Site_P5MD
Troubleshooting
FastEthernet
RNC
pmIfInBroadcastPkts
No
FastEthernet
RNC
pmIfInDiscards
No
FastEthernet
RNC
pmIfInErrors
No
FastEthernet
RNC
pmIfInMulticastPkts
No
FastEthernet
RNC
pmIfInOctetsHi
No
FastEthernet
RNC
pmIfInOctetsLo
No
FastEthernet
RNC
pmIfInUcastPkts
No
FastEthernet
RNC
pmIfInUnknownProtos
No
FastEthernet
RNC
pmIfOutBroadcastPkts
No
FastEthernet
RNC
pmIfOutDiscards
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 109 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
FastEthernet
RNC
pmIfOutErrors
No
FastEthernet
RNC
pmIfOutMulticastPkts
No
FastEthernet
RNC
pmIfOutOctetsHi
No
FastEthernet
RNC
pmIfOutOctetsLo
No
FastEthernet
RNC
pmIfOutUcastPkts
No
GigaBitEthernet
RNC
pmDot1qTpVlanPortInDiscardsLink1
No
GigaBitEthernet
RNC
pmDot1qTpVlanPortInDiscardsLink2
No
GigaBitEthernet
RNC
pmIfInBroadcastPktsLink1
No
GigaBitEthernet
RNC
pmIfInBroadcastPktsLink2
No
GigaBitEthernet
RNC
pmIfInDiscardsLink1
No
GigaBitEthernet
RNC
pmIfInDiscardsLink2
No
GigaBitEthernet
RNC
pmIfInErrorsLink1
No
GigaBitEthernet
RNC
pmIfInErrorsLink2
No
GigaBitEthernet
RNC
pmIfInMulticastPktsLink1
No
GigaBitEthernet
RNC
pmIfInMulticastPktsLink2
No
GigaBitEthernet
RNC
pmIfInOctetsLink1Hi
No
GigaBitEthernet
RNC
pmIfInOctetsLink1Lo
No
GigaBitEthernet
RNC
pmIfInOctetsLink2Hi
No
GigaBitEthernet
RNC
pmIfInOctetsLink2Lo
No
GigaBitEthernet
RNC
pmIfInUcastPktsLink1
No
GigaBitEthernet
RNC
pmIfInUcastPktsLink2
No
GigaBitEthernet
RNC
pmIfInUnknownProtosLink1
No
GigaBitEthernet
RNC
pmIfInUnknownProtosLink2
No
GigaBitEthernet
RNC
pmIfOutBroadcastPktsLink1
No
GigaBitEthernet
RNC
pmIfOutBroadcastPktsLink2
No
GigaBitEthernet
RNC
pmIfOutDiscardsLink1
No
GigaBitEthernet
RNC
pmIfOutDiscardsLink2
No
GigaBitEthernet
RNC
pmIfOutErrorsLink1
No
GigaBitEthernet
RNC
pmIfOutErrorsLink2
No
GigaBitEthernet
RNC
pmIfOutMulticastPktsLink1
No
GigaBitEthernet
RNC
pmIfOutMulticastPktsLink2
No
GigaBitEthernet
RNC
pmIfOutOctetsLink1Hi
No
GigaBitEthernet
RNC
pmIfOutOctetsLink1Lo
No
GigaBitEthernet
RNC
pmIfOutOctetsLink2Hi
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 110 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
GigaBitEthernet
RNC
pmIfOutOctetsLink2Lo
No
GigaBitEthernet
RNC
pmIfOutUcastPktsLink1
No
GigaBitEthernet
RNC
pmIfOutUcastPktsLink2
No
GsmRelation
Inter-RAT
pmNoAttOutIratHoCs57
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoAttOutIratHoMulti
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoAttOutIratHoSpeech
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoAttOutIratHoStandalone
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoAttOutSbHoSpeech
No
Add when SBHO is GA
GsmRelation
Inter-RAT
pmNoFailOutIratHoCs57GsmFailure
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoCs57ReturnOldChNotPhyChFail
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoCs57ReturnOldChPhyChFail
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoCs57UeRejection
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoMultiGsmFailure
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoMultiReturnOldChNotPhyChFail
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoMultiReturnOldChPhyChFail
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoMultiUeRejection
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoSpeechGsmFailure
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoSpeechReturnOldChNotPhyChFail
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoSpeechReturnOldChPhyChFail
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoSpeechUeRejection
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoStandaloneGsmFailure
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoStandaloneReturnOldChNotPhyChFail
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoStandaloneReturnOldChPhyChFail
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutIratHoStandaloneUeRejection
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoFailOutSbHoSpeechGsmFailure
No
Add when SBHO is GA
GsmRelation
Inter-RAT
pmNoFailOutSbHoSpeechReturnOldChNotPhyChFail
No
Add when SBHO is GA
GsmRelation
Inter-RAT
pmNoFailOutSbHoSpeechReturnOldChPhyChFail
No
Add when SBHO is GA
GsmRelation
Inter-RAT
pmNoFailOutSbHoSpeechUeRejection
No
Add when SBHO is GA
GsmRelation
Inter-RAT
pmNoOutIratCcAtt
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoOutIratCcReturnOldCh
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoOutIratCcSuccess
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoSuccessOutIratHoCs57
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoSuccessOutIratHoMulti
National_RNC_P5MD
Level 1 and 3 Scorecard
GsmRelation
Inter-RAT
pmNoSuccessOutIratHoSpeech
National_RNC_P5MD
Level 1 and 3 Scorecard
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 111 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
GsmRelation
Inter-RAT
pmNoSuccessOutIratHoStandalone
National_RNC_P5MD
Level 3 Scorecard
GsmRelation
Inter-RAT
pmNoSuccessOutSbHoSpeech
No
Add when SBHO is GA
Handover
RNC
pmNoSbHoMeasStart
No
Add when SBHO is GA
Handover
RNC
pmNoSuccessSbHo
No
Add when SBHO is GA
Handover
RNC
pmTotNoSbHo
No
Add when SBHO is GA
Hsdsch
Cell
pmHsDowntimeAuto
Primary Scanner
Primary Scanner
Hsdsch
Cell
pmHsDowntimeMan
Primary Scanner
Primary Scanner
HsDschResources
Site
pmAckReceived
National_Site_P5MD
Troubleshooting
HsDschResources
Site
pmAverageUserRate
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmIubMacdPduCellReceivedBits
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmNackReceived
National_Site_P5MD
Troubleshooting
HsDschResources
Site
pmNoActiveSubFrames
National_Site_P5MD
Troubleshooting
HsDschResources
Site
pmNoInactiveRequiredSubFrames
National_Site_P5MD
Troubleshooting
HsDschResources
Site
pmNoOfHsUsersPerTti
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmRemainingResourceCheck
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmReportedCqi
National_Site_P5MD
Troubleshooting
HsDschResources
Site
pmSampleNumHsPdschCodesAdded
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmSumAckedBits
National_Site_P5MD
Troubleshooting
HsDschResources
Site
pmSumNonEmptyUserBuffers
National_Site_P5MD
Troubleshooting
HsDschResources
Site
pmSumNumHsPdschCodesAdded
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmSumOfHsScchUsedPwr
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmSumTransmittedBits
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmTransmittedCarrierPowerNonHs
National_Site_P5MD
Dimensioning
HsDschResources
Site
pmUsedCqi
National_Site_P5MD
Troubleshooting
ImaGroup
Transport
pmGrFc
No
ImaGroup
Transport
pmGrFcFe
No
ImaGroup
Transport
pmGrUasIma
No
ImaLink
Transport - Site
pmIvIma
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmOifIma
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmRxFc
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmRxFcFe
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmRxStuffIma
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmRxUusIma
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmRxUusImaFe
National_Site_P5MD
Troubleshooting
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 112 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
ImaLink
Transport - Site
pmSesIma
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmSesImaFe
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmTxFc
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmTxFcFe
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmTxStuffIma
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmTxUusIma
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmTxUusImaFe
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmUasIma
National_Site_P5MD
Troubleshooting
ImaLink
Transport - Site
pmUasImaFe
National_Site_P5MD
Troubleshooting
Ip
Transport
pmNoOfHdrErrors
No
Ip
Transport
pmNoOfIpAddrErrors
No
Ip
Transport
pmNoOfIpForwDatagrams
No
Ip
Transport
pmNoOfIpInDiscards
No
Ip
Transport
pmNoOfIpInReceives
No
Ip
Transport
pmNoOfIpOutDiscards
No
Ip
Transport
pmNoOfIpReasmOKs
No
Ip
Transport
pmNoOfIpReasmReqds
No
IpAccessHostGpb
Transport
pmIcmpInDestUnreachs
No
IpAccessHostGpb
Transport
pmIcmpInEchoReps
No
IpAccessHostGpb
Transport
pmIcmpInEchos
No
IpAccessHostGpb
Transport
pmIcmpInErrors
No
IpAccessHostGpb
Transport
pmIcmpInMsgs
No
IpAccessHostGpb
Transport
pmIcmpInParamProbs
No
IpAccessHostGpb
Transport
pmIcmpInRedirects
No
IpAccessHostGpb
Transport
pmIcmpInSrcQuenchs
No
IpAccessHostGpb
Transport
pmIcmpInTimeExcds
No
IpAccessHostGpb
Transport
pmIcmpOutDestUnreachs
No
IpAccessHostGpb
Transport
pmIcmpOutEchoReps
No
IpAccessHostGpb
Transport
pmIcmpOutEchos
No
IpAccessHostGpb
Transport
pmIcmpOutErrors
No
IpAccessHostGpb
Transport
pmIcmpOutMsgs
No
IpAccessHostGpb
Transport
pmIcmpOutParmProbs
No
IpAccessHostGpb
Transport
pmIpFragCreates
No
IpAccessHostGpb
Transport
pmIpFragFails
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 113 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
IpAccessHostGpb
IpAccessHostGpb
Transport
pmIpFragOKs
No
Transport
pmIpInAddrErrors
No
IpAccessHostGpb
Transport
pmIpInDelivers
No
IpAccessHostGpb
Transport
pmIpInDiscards
No
IpAccessHostGpb
Transport
pmIpInHdrErrors
No
IpAccessHostGpb
Transport
pmIpInReceives
No
IpAccessHostGpb
Transport
pmIpInUnknownProtos
No
IpAccessHostGpb
Transport
pmIpOutDiscards
No
IpAccessHostGpb
Transport
pmIpOutRequests
No
IpAccessHostGpb
Transport
pmIpReasmFails
No
IpAccessHostGpb
Transport
pmIpReasmOKs
No
IpAccessHostGpb
Transport
pmIpReasmReqds
No
IpAccessHostGpb
Transport
pmUdpInDatagrams
No
IpAccessHostGpb
Transport
pmUdpInErrors
No
IpAccessHostGpb
Transport
pmUdpNoPorts
No
IpAccessHostGpb
Transport
pmUdpOutDatagrams
No
IpAccessHostSpb
RNC
pmIcmpInDestUnreachs
No
IpAccessHostSpb
RNC
pmIcmpInEchoReps
No
IpAccessHostSpb
RNC
pmIcmpInEchos
No
IpAccessHostSpb
RNC
pmIcmpInErrors
No
IpAccessHostSpb
RNC
pmIcmpInMsgs
No
IpAccessHostSpb
RNC
pmIcmpInParamProbs
No
IpAccessHostSpb
RNC
pmIcmpInRedirects
No
IpAccessHostSpb
RNC
pmIcmpInSrcQuenchs
No
IpAccessHostSpb
RNC
pmIcmpInTimeExcds
No
IpAccessHostSpb
RNC
pmIcmpOutDestUnreachs
No
IpAccessHostSpb
RNC
pmIcmpOutEchoReps
No
IpAccessHostSpb
RNC
pmIcmpOutEchos
No
IpAccessHostSpb
RNC
pmIcmpOutErrors
No
IpAccessHostSpb
RNC
pmIcmpOutMsgs
No
IpAccessHostSpb
RNC
pmIcmpOutParmProbs
No
IpAccessHostSpb
RNC
pmIpFragCreates
No
IpAccessHostSpb
RNC
pmIpFragFails
No
IpAccessHostSpb
RNC
pmIpFragOKs
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 114 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
IpAccessHostSpb
RNC
pmIpInAddrErrors
No
IpAccessHostSpb
RNC
pmIpInDelivers
No
IpAccessHostSpb
RNC
pmIpInDiscards
No
IpAccessHostSpb
RNC
pmIpInHdrErrors
No
IpAccessHostSpb
RNC
pmIpInReceives
No
IpAccessHostSpb
RNC
pmIpInUnknownProtos
No
IpAccessHostSpb
RNC
pmIpOutDiscards
No
IpAccessHostSpb
RNC
pmIpOutRequests
No
IpAccessHostSpb
RNC
pmIpReasmFails
No
IpAccessHostSpb
RNC
pmIpReasmOKs
No
IpAccessHostSpb
RNC
pmIpReasmReqds
No
IpAccessHostSpb
RNC
pmUdpInDatagrams
No
IpAccessHostSpb
RNC
pmUdpInErrors
No
IpAccessHostSpb
RNC
pmUdpNoPorts
No
IpAccessHostSpb
RNC
pmUdpOutDatagrams
No
IpAtmLink
Transport
pmNoOfIfInDiscards
No
IpAtmLink
Transport
pmNoOfIfInErrors
No
IpAtmLink
Transport
pmNoOfIfInNUcastPkts
No
IpAtmLink
Transport
pmNoOfIfInUcastPkts
No
IpAtmLink
Transport
pmNoOfifOutDiscards
No
IpAtmLink
Transport
pmNoOfIfOutNUcastPkts
No
IpAtmLink
Transport
pmNoOfIfOutUcastPkts
No
IpEthPacketDataRouter
RNC
pmNoFaultyIpPackets
No
IpEthPacketDataRouter
RNC
pmNoRoutedIpBytesDl
No
IpEthPacketDataRouter
RNC
pmNoRoutedIpBytesUl
No
IpEthPacketDataRouter
RNC
pmNoRoutedIpPacketsDl
No
IpEthPacketDataRouter
RNC
pmNoRoutedIpPacketsUl
No
IpEthPacketDataRouter
RNC
pmSamplesPacketDataRab
No
IpEthPacketDataRouter
RNC
pmSumPacketDataRab
No
IpInterface
RNC
pmDot1qTpVlanPortInFrames
No
IpInterface
RNC
pmDot1qTpVlanPortOutFrames
No
IpInterface
RNC
pmIfStatsIpAddrErrors
No
IpInterface
RNC
pmIfStatsIpInDiscards
No
IpInterface
RNC
pmIfStatsIpInHdrErrors
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 115 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
IpInterface
RNC
pmIfStatsIpInReceives
No
IpInterface
RNC
pmIfStatsIpOutDiscards
No
IpInterface
RNC
pmIfStatsIpOutRequests
No
IpInterface
RNC
pmIfStatsIpUnknownProtos
No
IubDataStreams
Site
pmCapAlloclubHsLimitingRatio
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmDchFramesCrcMismatch
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmDchFramesLate
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmDchFramesReceived
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmDchFramesTooLate
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmEdchIubLimitingRatio
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmHsDataFramesLost
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmHsDataFramesReceived
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmIubMacdPduRbsReceivedBits
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmNoUlIubLimitEul
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmRbsHsPdschCodePrio
National_Site_P5MD
Dimensioning
IubDataStreams
Site
pmTargetHsRate
National_Site_P5MD
Dimensioning
IubEdch
RNC
pmEdchDataFrameDelayIub
National_RNC_P5MD
Troubleshooting
IurLink
RNC
pmNoAttIncCnhhoCsNonSpeech
No
Add when CNHHO is GA
IurLink
RNC
pmNoAttIncCnhhoSpeech
No
Add when CNHHO is GA
IurLink
RNC
pmNoNormalRabReleaseCs64
Secondary Scanner
Secondary Scanner
IurLink
RNC
pmNoNormalRabReleaseCsStream
Secondary Scanner
Secondary Scanner
IurLink
RNC
pmNoNormalRabReleasePacket
Secondary Scanner
Secondary Scanner
IurLink
RNC
pmNoNormalRabReleasePacketStream
Secondary Scanner
Secondary Scanner
IurLink
RNC
pmNoNormalRabReleaseSpeech
Secondary Scanner
Secondary Scanner
IurLink
RNC
pmNoOfRlForDriftingUesPerDrnc
Secondary Scanner
Secondary Scanner
IurLink
RNC
pmNoSuccIncCnhhoCsNonSpeech
No
Add when CNHHO is GA
IurLink
RNC
pmNoSuccIncCnhhoSpeech
No
Add when CNHHO is GA
IurLink
RNC
pmNoSystemRabReleaseCs64
Secondary Scanner
Secondary Scanner
IurLink
RNC
pmNoSystemRabReleaseCsStream
Secondary Scanner
Secondary Scanner
IurLink
RNC
pmNoSystemRabReleasePacket
Secondary Scanner
Secondary Scanner - Level 3 Scorecard
IurLink
RNC
pmNoSystemRabReleasePacketStream
Secondary Scanner
IurLink
RNC
pmNoSystemRabReleaseSpeech
Secondary Scanner
Secondary Scanner - Level 3 Scorecard
Secondary Scanner - Level 1 and 3
Scorecard
J1PhysPathTerm
Transport
pmEs
No
J1PhysPathTerm
Transport
pmSes
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 116 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
J1PhysPathTerm
Transport
pmUas
No
LoadControl
RNC
pmAdmittedRequestsB0
No
LoadControl
RNC
pmAdmittedRequestsB1
No
LoadControl
RNC
pmAdmittedRequestsF0
No
LoadControl
RNC
pmAdmittedRequestsF1
No
LoadControl
RNC
pmAdmittedRequestsF2
No
LoadControl
RNC
pmAdmittedRequestsF3
No
LoadControl
RNC
pmAdmittedRequestsF4
No
LoadControl
RNC
pmRefusedRequestsB0
No
LoadControl
RNC
pmRefusedRequestsB1
No
LoadControl
RNC
pmRefusedRequestsF0
No
LoadControl
RNC
pmRefusedRequestsF1
No
LoadControl
RNC
pmRefusedRequestsF2
No
LoadControl
RNC
pmRefusedRequestsF3
No
LoadControl
RNC
pmRefusedRequestsF4
No
LoadControl
RNC
pmSamplesMeasuredLoad
Secondary Scanner
Secondary Scanner
LoadControl
RNC
pmSumMeasuredLoad
Secondary Scanner
Secondary Scanner
LocationArea
RNC
pmCnInitPagingToIdleUeLa
National_RNC_P5MD
Dimensioning
M3uAssociation
Transport
pmNoOfAspacAckReceived
No
M3uAssociation
Transport
pmNoOfAspacAckSent
No
M3uAssociation
Transport
pmNoOfAspacReceived
No
M3uAssociation
Transport
pmNoOfAspacSent
No
M3uAssociation
Transport
pmNoOfAspdnAckReceived
No
M3uAssociation
Transport
pmNoOfAspdnAckSent
No
M3uAssociation
Transport
pmNoOfAspdnReceived
No
M3uAssociation
Transport
pmNoOfAspdnSent
No
M3uAssociation
Transport
pmNoOfAspiaAckReceived
No
M3uAssociation
Transport
pmNoOfAspiaAckSent
No
M3uAssociation
Transport
pmNoOfAspiaReceived
No
M3uAssociation
Transport
pmNoOfAspiaSent
No
M3uAssociation
Transport
pmNoOfAspupAckReceived
No
M3uAssociation
Transport
pmNoOfAspupAckSent
No
M3uAssociation
Transport
pmNoOfAspupReceived
No
M3uAssociation
Transport
pmNoOfAspupSent
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 117 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
M3uAssociation
M3uAssociation
Transport
pmNoOfCommunicationLost
No
Transport
pmNoOfCongestions
No
M3uAssociation
Transport
pmNoOfDataMsgRec
No
M3uAssociation
Transport
pmNoOfDataMsgSent
No
M3uAssociation
Transport
pmNoOfDaudMsgRec
No
M3uAssociation
Transport
pmNoOfDaudMsgSent
No
M3uAssociation
Transport
pmNoOfDavaRec
No
M3uAssociation
Transport
pmNoOfDavaSent
No
M3uAssociation
Transport
pmNoOfDunaRec
No
M3uAssociation
Transport
pmNoOfDunaSent
No
M3uAssociation
Transport
pmNoOfDupuRec
No
M3uAssociation
Transport
pmNoOfDupuSent
No
M3uAssociation
Transport
pmNoOfErrorMsgRec
No
M3uAssociation
Transport
pmNoOfErrorMsgSent
No
M3uAssociation
Transport
pmNoOfM3uaDataMsgDiscarded
No
M3uAssociation
Transport
pmNoOfNotifyMsgRec
No
M3uAssociation
Transport
pmNoOfSconRec
No
M3uAssociation
Transport
pmNoOfSconSent
No
MediumAccessUnit
Transport
pmNoOfDot3StatsFCSErrors
No
MediumAccessUnit
Transport
pmNoOfDot3StatsLateCollisions
No
Mtp3bAp
Transport
pmNoOfAdjacentSPNotAccessible
No
Mtp3bAp
Transport
pmNoOfUserPartUnavailRec
No
Mtp3bSlAnsi
Transport
pmNoOfAALINServiceInd
No
Mtp3bSlChina
Transport
pmNoOfAALOUTInd
No
Mtp3bSlItu
Transport
pmNoOfCBDSent
No
Mtp3bSlTtc
Transport
pmNoOfCOOXCOSent
No
Mtp3bSlTtc
Transport
pmNoOfLocalLinkCongestCeaseRec
No
Mtp3bSlTtc
Transport
pmNoOfLocalLinkCongestRec
No
Mtp3bSlTtc
Transport
pmNoOfMSURec
No
Mtp3bSlTtc
Transport
pmNoOfMSUSent
No
Mtp3bSpAnsi
Transport
pmNoOfCBARec
No
Mtp3bSpAnsi
Transport
pmNoOfCBASent
No
Mtp3bSpAnsi
Transport
pmNoOfChangeBackDeclRec
No
Mtp3bSpAnsi
Transport
pmNoOfChangeOverRec
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 118 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Mtp3bSpAnsi
Transport
pmNoOfCOAXCARec
No
Mtp3bSpAnsi
Transport
pmNoOfCOAXCASent
No
Mtp3bSpAnsi
Transport
pmNoOfControlledRerouteSuccessPerf
No
Mtp3bSpAnsi
Transport
pmNoOfECARec
No
Mtp3bSpAnsi
Transport
pmNoOfECASent
No
Mtp3bSpAnsi
Transport
pmNoOfECOSent
No
Mtp3bSpAnsi
Transport
pmNoOfEmergencyChangeOverRec
No
Mtp3bSpAnsi
Transport
pmNoOfForcedRerouteSuccessPerf
No
Mtp3bSpAnsi
Transport
pmNoOfIncomingAssocEstabRequestInStateDownWhenStateEstabIsBlocked
No
Mtp3bSpAnsi
Transport
pmNoOfLowerPrioMsgDiscarded
No
Mtp3bSpAnsi
Transport
pmNoOfMaxTrialsForAssocActivReached
No
Mtp3bSpAnsi
Transport
pmNoOfMaxTrialsForAssocEstabReached
No
Mtp3bSpAnsi
Transport
pmNoOfSctpAssociationRestart
No
Mtp3bSpAnsi
Transport
pmNoOfSctpBufOverflow
No
Mtp3bSpAnsi
Transport
pmNoOfSctpCommunicationErr
No
Mtp3bSpAnsi
Transport
pmNoOfSctpNetworkStatusChange
No
Mtp3bSpAnsi
Transport
pmNoOfSctpResumeSending
No
Mtp3bSpAnsi
Transport
pmNoOfSctpSendFailure
No
Mtp3bSpAnsi
Transport
pmNoOfSLTAFirstTimeOutRec
No
Mtp3bSpAnsi
Transport
pmNoOfSLTASecondTimeOutRec
No
Mtp3bSpAnsi
Transport
pmNoOfSuccessAssocAbort
No
Mtp3bSpAnsi
Transport
pmNoOfSuccessAssocEstablish
No
Mtp3bSpAnsi
Transport
pmNoOfSuccessAssocShutDown
No
Mtp3bSpAnsi
Transport
pmNoOfTimerT21WasStarted
No
Mtp3bSpAnsi
Transport
pmNoOfTRARec
No
Mtp3bSpAnsi
Transport
pmNoOfTRASent
No
Mtp3bSpAnsi
Transport
pmNoOfUnsuccessAssocEstablish
No
Mtp3bSpAnsi
Transport
pmNoOfUnsuccessForcedRerouting
No
Mtp3bSpAnsi
Transport
pmNoOfUPMsgDiscardedDueToRoutingErr
No
Mtp3bSpChina
Transport
pmNoOfCBARec
No
Mtp3bSpChina
Transport
pmNoOfCBASent
No
Mtp3bSpChina
Transport
pmNoOfChangeBackDeclRec
No
Mtp3bSpChina
Transport
pmNoOfChangeOverRec
No
Mtp3bSpChina
Transport
pmNoOfCOAXCARec
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 119 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Mtp3bSpChina
Transport
pmNoOfCOAXCASent
No
Mtp3bSpChina
Transport
pmNoOfControlledRerouteSuccessPerf
No
Mtp3bSpChina
Transport
pmNoOfECARec
No
Mtp3bSpChina
Transport
pmNoOfECASent
No
Mtp3bSpChina
Transport
pmNoOfECOSent
No
Mtp3bSpChina
Transport
pmNoOfEmergencyChangeOverRec
No
Mtp3bSpChina
Transport
pmNoOfForcedRerouteSuccessPerf
No
Mtp3bSpChina
Transport
pmNoOfIncomingAssocEstabRequestInStateDownWhenStateEstabIsBlocked
No
Mtp3bSpChina
Transport
pmNoOfLowerPrioMsgDiscarded
No
Mtp3bSpChina
Transport
pmNoOfMaxTrialsForAssocActivReached
No
Mtp3bSpChina
Transport
pmNoOfMaxTrialsForAssocEstabReached
No
Mtp3bSpChina
Transport
pmNoOfSctpAssociationRestart
No
Mtp3bSpChina
Transport
pmNoOfSctpBufOverflow
No
Mtp3bSpChina
Transport
pmNoOfSctpCommunicationErr
No
Mtp3bSpChina
Transport
pmNoOfSctpNetworkStatusChange
No
Mtp3bSpChina
Transport
pmNoOfSctpResumeSending
No
Mtp3bSpChina
Transport
pmNoOfSctpSendFailure
No
Mtp3bSpChina
Transport
pmNoOfSLTAFirstTimeOutRec
No
Mtp3bSpChina
Transport
pmNoOfSLTASecondTimeOutRec
No
Mtp3bSpChina
Transport
pmNoOfSuccessAssocAbort
No
Mtp3bSpChina
Transport
pmNoOfSuccessAssocEstablish
No
Mtp3bSpChina
Transport
pmNoOfSuccessAssocShutDown
No
Mtp3bSpChina
Transport
pmNoOfTimerT21WasStarted
No
Mtp3bSpChina
Transport
pmNoOfTRARec
No
Mtp3bSpChina
Transport
pmNoOfTRASent
No
Mtp3bSpChina
Transport
pmNoOfUnsuccessAssocEstablish
No
Mtp3bSpChina
Transport
pmNoOfUnsuccessForcedRerouting
No
Mtp3bSpChina
Transport
pmNoOfUPMsgDiscardedDueToRoutingErr
No
Mtp3bSpItu
Transport
pmNoOfCBARec
No
Mtp3bSpItu
Transport
pmNoOfCBASent
No
Mtp3bSpItu
Transport
pmNoOfChangeBackDeclRec
No
Mtp3bSpItu
Transport
pmNoOfChangeOverRec
No
Mtp3bSpItu
Transport
pmNoOfCOAXCARec
No
Mtp3bSpItu
Transport
pmNoOfCOAXCASent
No
ND-00150
Rev. 3.0 09/09/2007
Active within scanner
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 120 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Mtp3bSpItu
Transport
pmNoOfControlledRerouteSuccessPerf
No
Mtp3bSpItu
Transport
pmNoOfECARec
No
Mtp3bSpItu
Transport
pmNoOfECASent
No
Mtp3bSpItu
Transport
pmNoOfECOSent
No
Mtp3bSpItu
Transport
pmNoOfEmergencyChangeOverRec
No
Mtp3bSpItu
Transport
pmNoOfForcedRerouteSuccessPerf
No
Mtp3bSpItu
Transport
pmNoOfIncomingAssocEstabRequestInStateDownWhenStateEstabIsBlocked
No
Mtp3bSpItu
Transport
pmNoOfLowerPrioMsgDiscarded
No
Mtp3bSpItu
Transport
pmNoOfMaxTrialsForAssocActivReached
No
Mtp3bSpItu
Transport
pmNoOfMaxTrialsForAssocEstabReached
No
Mtp3bSpItu
Transport
pmNoOfSctpAssociationRestart
No
Mtp3bSpItu
Transport
pmNoOfSctpBufOverflow
No
Mtp3bSpItu
Transport
pmNoOfSctpCommunicationErr
No
Mtp3bSpItu
Transport
pmNoOfSctpNetworkStatusChange
No
Mtp3bSpItu
Transport
pmNoOfSctpResumeSending
No
Mtp3bSpItu
Transport
pmNoOfSctpSendFailure
No
Mtp3bSpItu
Transport
pmNoOfSLTAFirstTimeOutRec
No
Mtp3bSpItu
Transport
pmNoOfSLTASecondTimeOutRec
No
Mtp3bSpItu
Transport
pmNoOfSuccessAssocAbort
No
Mtp3bSpItu
Transport
pmNoOfSuccessAssocEstablish
No
Mtp3bSpItu
Transport
pmNoOfSuccessAssocShutDown
No
Mtp3bSpItu
Transport
pmNoOfTimerT21WasStarted
No
Mtp3bSpItu
Transport
pmNoOfTRARec
No
Mtp3bSpItu
Transport
pmNoOfTRASent
No
Mtp3bSpItu
Transport
pmNoOfUnsuccessAssocEstablish
No
Mtp3bSpItu
Transport
pmNoOfUnsuccessAssocShutDown
Mtp3bSpItu
Transport
pmNoOfUnsuccessForcedRerouting
No
Mtp3bSpItu
Transport
pmNoOfUPMsgDiscardedDueToRoutingErr
No
Mtp3bSpTtc
Transport
pmNoOfSctpBufOverflow
Mtp3bSpTtc
Transport
pmInStateDownWhenStateEstabIsBlocked
Mtp3bSpTtc
Transport
pmNoOfCBARec
Mtp3bSpTtc
Transport
pmNoOfCBASent
No
Mtp3bSpTtc
Transport
pmNoOfChangeBackDeclRec
No
Mtp3bSpTtc
Transport
pmNoOfChangeOverRec
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
No
Page 121 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Mtp3bSpTtc
Transport
pmNoOfCOAXCARec
No
Mtp3bSpTtc
Transport
pmNoOfCOAXCASent
No
Mtp3bSpTtc
Transport
pmNoOfControlledRerouteSuccessPerf
No
Mtp3bSpTtc
Transport
pmNoOfECARec
No
Mtp3bSpTtc
Transport
pmNoOfECASent
No
Mtp3bSpTtc
Transport
pmNoOfECOSent
No
Mtp3bSpTtc
Transport
pmNoOfEmergencyChangeOverRec
No
Mtp3bSpTtc
Transport
pmNoOfForcedRerouteSuccessPerf
No
Mtp3bSpTtc
Transport
pmNoOfIncomingAssocEstabRequest
No
Mtp3bSpTtc
Transport
pmNoOfIncomingAssocEstabRequestInStateDownWhenStateEstabIsBlocked
No
Mtp3bSpTtc
Transport
pmNoOfMaxTrialsForAssocActivReached
No
Mtp3bSpTtc
Transport
pmNoOfMaxTrialsForAssocEstabReached
No
Mtp3bSpTtc
Transport
pmNoOfSctpAssociationRestart
No
Mtp3bSpTtc
Transport
pmNoOfSctpBufOverflow
No
Mtp3bSpTtc
Transport
pmNoOfSctpCommunicationErr
No
Mtp3bSpTtc
Transport
pmNoOfSctpNetworkStatusChange
No
Mtp3bSpTtc
Transport
pmNoOfSctpResumeSending
No
Mtp3bSpTtc
Transport
pmNoOfSctpSendFailure
No
Mtp3bSpTtc
Transport
pmNoOfSLTAFirstTimeOutRec
No
Mtp3bSpTtc
Transport
pmNoOfSLTASecondTimeOutRec
No
Mtp3bSpTtc
Transport
pmNoOfSuccessAssocAbort
No
Mtp3bSpTtc
Transport
pmNoOfSuccessAssocEstablish
No
Mtp3bSpTtc
Transport
pmNoOfSuccessAssocShutDown
No
Mtp3bSpTtc
Transport
pmNoOfTRARec
No
Mtp3bSpTtc
Transport
pmNoOfTRASent
No
Mtp3bSpTtc
Transport
pmNoOfUnsuccessAssocEstablish
No
Mtp3bSpTtc
Transport
pmNoOfUnsuccessAssocShutDown
No
Mtp3bSpTtc
Transport
pmNoOfUnsuccessForcedRerouting
No
Mtp3bSpTtc
Transport
pmNoOfUPMsgDiscardedDueToRoutingErr
No
Mtp3bSr
Transport
pmNoOfSecondsAccumulatedRouteUnavailable
No
Mtp3bSrs
Transport
pmNoOfDiscardedMsgFromBroadToNarrow
No
Mtp3bSrs
Transport
pmNoOfSecsAccRouteSetUnavailable
No
Mtp3bSrs
Transport
pmNoOfTransferAllowedRec
No
Mtp3bSrs
Transport
pmNoOfTransferControlledRec
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 122 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Mtp3bSrs
Transport
pmNoOfTransferProhibitedRec
No
NbapCommon
Site
pmNoOfDiscardedMsg
No
NbapCommon
Site
pmNoOfDiscardedNbapMessages
National_Site_P5MD
NniSaalTp
Transport - RNC
pmLinkInServiceTime
No
NniSaalTp
Transport - RNC
pmNoOfAlignmentFailures
No
NniSaalTp
Transport - RNC
pmNoOfAllSLFailures
No
NniSaalTp
Transport - RNC
pmNoOfLocalCongestions
National_RNC_P5MD
NniSaalTp
Transport - RNC
pmNoOfNoResponses
No
NniSaalTp
Transport - RNC
pmNoOfOtherErrors
No
NniSaalTp
Transport - RNC
pmNoOfProtocolErrors
No
NniSaalTp
Transport - RNC
pmNoOfReceivedSDUs
No
NniSaalTp
Transport - RNC
pmNoOfRemoteCongestions
No
NniSaalTp
Transport - RNC
pmNoOfSentSDUs
No
NniSaalTp
Transport - RNC
pmNoOfSequenceDataLosses
No
NniSaalTp
Transport - RNC
pmNoOfUnsuccReTransmissions
No
Os155SpiTtp
Transport
pmMsBbe
No
Os155SpiTtp
Transport
pmMsEs
No
Os155SpiTtp
Transport
pmMsSes
No
Os155SpiTtp
Transport
pmMsUas
No
Ospf
Transport
pmNoOfOspfOriginateNewLsas
No
Ospf
Transport
pmNoOfOspfRxNewLsas
No
OspfArea
Transport
pmNoOfOspfSpfRuns
No
OspfInterface
Transport
pmNoOfOspfIfEvents
No
PacketDataRouter
RNC
pmNoFaultyIpPackets
National_RNC_P5MD
Dimensioning
PacketDataRouter
RNC
pmNoRoutedIpBytesDl
National_RNC_P5MD
Dimensioning
PacketDataRouter
RNC
pmNoRoutedIpBytesUl
National_RNC_P5MD
Dimensioning
PacketDataRouter
RNC
pmNoRoutedIpPacketsDl
National_RNC_P5MD
Dimensioning
PacketDataRouter
RNC
pmNoRoutedIpPacketsUl
National_RNC_P5MD
Dimensioning
PacketDataRouter
RNC
pmSamplesPacketDataRab
No
PacketDataRouter
RNC
pmSumPacketDataRab
No
Paging
RNC
pmCnInitPagingToIdleUe
No
Paging
RNC
pmNoPageDiscardCmpLoadC
National_RNC_P5MD
Dimensioning
PdrDevice
RNC
pmSamplesMeasuredPdrSpLoad
Secondary Scanner
Secondary Scanner
PdrDevice
RNC
pmSumMeasuredPdrSpLoad
Secondary Scanner
Secondary Scanner
ND-00150
Rev. 3.0 09/09/2007
Active within scanner
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 123 of 170
© 2007 AT&T
Reason
Dimensioning
Troubleshooting
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
Prach
Site
pmNoPreambleFalseDetection
National_Site_P5MD
Troubleshooting
Prach
Site
pmPopagationDelay
No
Prach
Site
pmReceivedPreambleSir
No
Prach
Site
pmSuccReceivedBlocks
No
Prach
Site
pmUnsuccReceivedBlocks
No
Rach
Cell
pmFaultyTransportBlocks
National_RNC_P5MD
Troubleshooting
Rach
Cell
pmNoRecRandomAccSuccess
National_RNC_P5MD
Troubleshooting
Rach
Cell
pmTransportBlocks
National_RNC_P5MD
Troubleshooting
RadioLinks
Site
pmAverageSir
No
RadioLinks
Site
pmAverageSirError
No
RadioLinks
Site
pmDpcchBer
No
RadioLinks
Site
pmDpchCodePowerSf128
No
Consider activating
RadioLinks
Site
pmDpchCodePowerSf16
No
Consider activating
RadioLinks
Site
pmDpchCodePowerSf256
No
Consider activating
RadioLinks
Site
pmDpchCodePowerSf32
No
Consider activating
RadioLinks
Site
pmDpchCodePowerSf4
No
RadioLinks
Site
pmDpchCodePowerSf64
No
Consider activating
RadioLinks
Site
pmDpchCodePowerSf8
No
Consider activating
RadioLinks
Site
pmDpdchBer
No
RadioLinks
Site
pmOutOfSynch
National_Site_P5MD
Troubleshooting
RadioLinks
Site
pmRLSSupSynchToUnsynch
National_Site_P5MD
Troubleshooting
RadioLinks
Site
pmRLSSupWaitToOutOfSynch
National_Site_P5MD
Troubleshooting
RadioLinks
Site
pmUISynchTime
No
RadioLinks
Site
pmUISynchTimeSHO
No
Ranap
RNC
pmNnsfLoadDistributionRouted
No
Ranap
RNC
pmNnsfNriRouted
No
Rcs
RNC
pmNoReleaseCchWaitCuT
Secondary Scanner
Secondary Scanner
Rcs
RNC
pmNoReleaseDchRcLostT
Secondary Scanner
Secondary Scanner
Rcs
RNC
pmNoRlcErrors
Secondary Scanner
Secondary Scanner
RncFunction
RNC
pmMocnRedirections
No
RncFunction
RNC
pmNoDiscardSduDcch
No
RncFunction
RNC
pmNoDiscardSduDtch
No
RncFunction
RNC
pmNoInvalidRabEstablishAttempts
National_RNC_P5MD
RncFunction
RNC
pmNoInvalidRabReleaseAttempts
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 124 of 170
© 2007 AT&T
Add when Streaming QoS is GA
Troubleshooting
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
RncFunction
RNC
pmNoIuSigEstablishAttemptCs
No
RncFunction
RNC
pmNoIuSigEstablishAttemptPs
No
RncFunction
RNC
pmNoIuSigEstablishSuccessCs
No
RncFunction
RNC
pmNoIuSigEstablishSuccessPs
No
RncFunction
RNC
pmNoOfPacketCallDuration1
Primary Scanner
Primary Scanner
RncFunction
RNC
pmNoOfPacketCallDuration2
Primary Scanner
Primary Scanner
RncFunction
RNC
pmNoOfPacketCallDuration3
Primary Scanner
Primary Scanner
RncFunction
RNC
pmNoOfPacketCallDuration4
Primary Scanner
Primary Scanner
RncFunction
RNC
pmNoOfPacketCallDurationHs1
Primary Scanner
Primary Scanner
RncFunction
RNC
pmNoOfPacketCallDurationHs2
Primary Scanner
Primary Scanner
RncFunction
RNC
pmNoOfPacketCallDurationHs3
Primary Scanner
Primary Scanner
RncFunction
RNC
pmNoOfPacketCallDurationHs4
Primary Scanner
Primary Scanner
RncFunction
RNC
pmNoOfRedirectedEmergencyCalls
Primary Scanner
Primary Scanner - Level 3 Scorecard
RncFunction
RNC
pmNoRabEstablishFailureUeCapability
Secondary Scanner
Secondary Scanner
RncFunction
RNC
pmNoReceivedSduDcch
No
RncFunction
RNC
pmNoReceivedSduDtch
No
RncFunction
RNC
pmNoRetransPduDcch
No
RncFunction
RNC
pmNoRetransPduDtch
No
RncFunction
RNC
pmNoSentPduDcch
No
RncFunction
RNC
pmNoSentPduDtch
No
RncFunction
RNC
pmPositioningReqAtt
No
RncFunction
RNC
pmPositioningReqSucc
No
RncFunction
RNC
pmSentPacketData1
Primary Scanner
RncFunction
RNC
pmSentPacketData2
Primary Scanner
RncFunction
RNC
pmSentPacketData3
Primary Scanner
RncFunction
RNC
pmSentPacketData4
Primary Scanner
RncFunction
RNC
pmSentPacketDataHs1
Primary Scanner
RncFunction
RNC
pmSentPacketDataHs2
Primary Scanner
RncFunction
RNC
pmSentPacketDataHs3
Primary Scanner
RncFunction
RNC
pmSentPacketDataHs4
Primary Scanner
ND-00150
Rev. 3.0 09/09/2007
Active within scanner
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 125 of 170
© 2007 AT&T
Reason
Primary Scanner - Level 3 Scorecard and
Dimensioning
Primary Scanner - Level 3 Scorecard and
Dimensioning
Primary Scanner - Level 3 Scorecard and
Dimensioning
Primary Scanner - Level 3 Scorecard and
Dimensioning
Primary Scanner - Level 3 Scorecard and
Dimensioning
Primary Scanner - Level 3 Scorecard and
Dimensioning
Primary Scanner - Level 3 Scorecard and
Dimensioning
Primary Scanner - Level 3 Scorecard and
Dimensioning
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
RncFunction
RNC
pmSentPacketDataInclRetrans1
Primary Scanner
Primary Scanner
RncFunction
RNC
pmSentPacketDataInclRetrans2
Primary Scanner
Primary Scanner
RncFunction
RNC
pmSentPacketDataInclRetrans3
Primary Scanner
Primary Scanner
RncFunction
RNC
pmSentPacketDataInclRetrans4
Primary Scanner
Primary Scanner
RncFunction
RNC
pmSentPacketDataInclRetransHs1
Primary Scanner
Primary Scanner
RncFunction
RNC
pmSentPacketDataInclRetransHs2
Primary Scanner
Primary Scanner
RncFunction
RNC
pmSentPacketDataInclRetransHs3
Primary Scanner
Primary Scanner
RncFunction
RNC
pmSentPacketDataInclRetransHs4
Primary Scanner
Primary Scanner
RncFunction
RNC
pmTotalPacketDuration1
Primary Scanner
Primary Scanner - Level 3 Scorecard
RncFunction
RNC
pmTotalPacketDuration2
Primary Scanner
Primary Scanner - Level 3 Scorecard
RncFunction
RNC
pmTotalPacketDuration3
Primary Scanner
Primary Scanner - Level 3 Scorecard
RncFunction
RNC
pmTotalPacketDuration4
Primary Scanner
Primary Scanner - Level 3 Scorecard
RncFunction
RNC
pmTotalPacketDurationHs1
Primary Scanner
Primary Scanner - Level 3 Scorecard
RncFunction
RNC
pmTotalPacketDurationHs2
Primary Scanner
Primary Scanner - Level 3 Scorecard
RncFunction
RNC
pmTotalPacketDurationHs3
Primary Scanner
Primary Scanner - Level 3 Scorecard
RncFunction
RNC
pmTotalPacketDurationHs4
Primary Scanner
Primary Scanner - Level 3 Scorecard
RoutingArea
RNC
pmCnInitPagingToIdleUeRa
No
SccpAccountingCriteria
Transport
pmNoOfMsg
No
SccpAccountingCriteria
Transport
pmNoOfOctets
No
Sccpch
Site
pmNoOfTfc1OnFach1
No
Add when FACH is GA
Sccpch
Site
pmNoOfTfc2OnFach1
No
Add when FACH is GA
Sccpch
Site
pmNoOfTfc3OnFach2
No
Add when FACH is GA
SccpPolicing
Transport
pmNoOfRejectMsg
No
SccpScrc
Transport
pmNoOfConnectFailure
No
SccpScrc
Transport
pmNoOfHopCounterViolation
No
SccpScrc
Transport
pmNoOfRoutingFailNetworkCongest
No
SccpScrc
Transport
pmNoOfRoutingFailNoTransAddrOfSuchNature
No
SccpScrc
Transport
pmNoOfRoutingFailNoTransSpecificAddr
No
SccpScrc
Transport
pmNoOfRoutingFailReasonUnknown
No
SccpScrc
Transport
pmNoOfRoutingFailSubsysUnavail
No
SccpScrc
Transport
pmNoOfRoutingFailUnequippedSubsys
No
SccpScrc
Transport
pmNoOfRoutingFailure
No
SccpScrc
Transport
pmNoOfRoutingFailurePointCodeUnAvail
No
SccpSp
Transport
pmNoOfConInUseExceedHighWaterMark
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 126 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
SccpSp
Transport
pmNoOfConInUseReceededLowWaterMark
No
SccpSp
Transport
pmNoOfCREFRecFromNL
No
SccpSp
Transport
pmNoOfCREFSentToNL
No
SccpSp
Transport
pmNoOfCRRec
No
SccpSp
Transport
pmNoOfCRSent
No
SccpSp
Transport
pmNoOfDT1Rec
No
SccpSp
Transport
pmNoOfDT1Sent
No
SccpSp
Transport
pmNoOfERRRec
No
SccpSp
Transport
pmNoOfERRSent
No
SccpSp
Transport
pmNoOfLUDTRec
No
SccpSp
Transport
pmNoOfLUDTSSent
No
SccpSp
Transport
pmNoOfRLSDRecFromNL
No
SccpSp
Transport
pmNoOfRLSDSentToNL
No
SccpSp
Transport
pmNoOfSubsysAllowedSent
No
SccpSp
Transport
pmNoOfUDTRec
No
SccpSp
Transport
pmNoOfUDTSent
No
SccpSp
Transport
pmNoOfUDTSRec
No
SccpSp
Transport
pmNoOfUDTSSent
No
SccpSp
Transport
pmNoOfXUDTRec
No
SccpSp
Transport
pmNoOfXUDTSent
No
SccpSp
Transport
pmNoOfXUDTSRec
No
SccpSp
Transport
pmNoOfXUDTSSent
No
Sctp
Transport
pmSctpAborted
No
Sctp
Transport
pmSctpActiveEstab
No
Sctp
Transport
pmSctpCurrEstab
No
Sctp
Transport
pmSctpPassiveEstab
No
Sctp
Transport
pmSctpShutdowns
No
Sctp
Transport
pmSctpStatAssocOutOfBlue
No
Sctp
Transport
pmSctpStatChecksumErrorCounter
No
Sctp
Transport
pmSctpStatCommResume
No
Sctp
Transport
pmSctpStatCommStop
No
Sctp
Transport
pmSctpStatFragmentedUserMsg
No
Sctp
Transport
pmSctpStatOutOfOrderRecChunks
No
Sctp
Transport
pmSctpStatOutOfOrderSendChunks
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 127 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Sctp
Transport
pmSctpStatReassembledUserMsg
No
Sctp
Transport
pmSctpStatRecChunks
No
Sctp
Transport
pmSctpStatRecChunksDropped
No
Sctp
Transport
pmSctpStatReceivedControlChunks
No
Sctp
Transport
pmSctpStatReceivedPackages
No
Sctp
Transport
pmSctpStatRetransChunks
No
Sctp
Transport
pmSctpStatSentChunks
No
Sctp
Transport
pmSctpStatSentChunksDropped
No
Sctp
Transport
pmSctpStatSentControlChunks
No
Sctp
Transport
pmSctpStatSentPackages
No
SecurityHandling
RNC
pmIntegrityFailureRrcMsg
National_RNC_P5MD
Sts1SpeTtp
Transport
pmEsp
No
Sts1SpeTtp
Transport
pmSesp
No
Sts1SpeTtp
Transport
pmUasp
No
Sts3CspeTtp
Transport
pmEsp
No
Sts3CspeTtp
Transport
pmSesp
No
Sts3CspeTtp
Transport
pmUasp
No
T1PhysPathTerm
Transport - Site
pmEs
National_Site_P5MD
Troubleshooting
T1PhysPathTerm
Transport - Site
pmSes
National_Site_P5MD
Troubleshooting
T1PhysPathTerm
Transport - Site
pmUas
National_Site_P5MD
Troubleshooting
T1Ttp
Transport - RXI
pmEs
National_RXI_P5MD
Troubleshooting
T1Ttp
Transport - RXI
pmSes
National_RXI_P5MD
Troubleshooting
T1Ttp
Transport - RXI
pmUas
National_RXI_P5MD
Troubleshooting
T3PhysPathTerm
Transport - Site
pmEsCpp
National_Site_P5MD
Troubleshooting
T3PhysPathTerm
Transport - Site
pmSesCpp
National_Site_P5MD
Troubleshooting
T3PhysPathTerm
Transport - RBS
pmUas
No
UePositioning
RNC
pmPositioningReqAttCellId
No
UePositioning
RNC
pmPositioningReqAttEsCellId
No
UePositioning
RNC
pmPositioningReqReAttCellId
No
UePositioning
RNC
pmPositioningReqReAttEsCellId
No
UePositioning
RNC
pmPositioningReqReAttSuccCellId
No
UePositioning
RNC
pmPositioningReqSuccCellId
No
UePositioning
RNC
pmPositioningReqSuccCellIdQosSucc
No
UeRc
RNC
pmDlDchTrafficVolumeBeforeSplit
National_RNC_P5MD
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 128 of 170
© 2007 AT&T
Reason
Troubleshooting
Dimensioning
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UeRc
RNC
pmDlFachTrafficVolume
National_RNC_P5MD
Dimensioning
UeRc
RNC
pmFaultyTransportBlocksAcUl
Primary Scanner
Primary Scanner
UeRc
RNC
pmNoRabEstablishAttempts
National_RNC_P5MD
Troubleshooting
UeRc
RNC
pmNoRabEstablishSuccess
National_RNC_P5MD
Troubleshooting
UeRc
RNC
pmNoRabReleaseAttempts
National_RNC_P5MD
Troubleshooting
UeRc
RNC
pmNoRabReleaseSuccess
National_RNC_P5MD
Troubleshooting
UeRc
RNC
pmSamplesRabEstablish
National_RNC_P5MD
Troubleshooting
UeRc
RNC
pmSumRabEstablish
National_RNC_P5MD
Troubleshooting
UeRc
RNC
pmTransportBlocksAcUl
Primary Scanner
Primary Scanner
UeRc
RNC
pmUlDchTrafficVolumeAfterComb
National_RNC_P5MD
Dimensioning
UeRc
RNC
pmUlRachTrafficVolume
National_RNC_P5MD
Dimensioning
UniSaalTp
Transport - RNC
pmLinkInServiceTime
No
UniSaalTp
Transport - RNC
pmNoOfAllSLFailures
No
UniSaalTp
Transport - RNC
pmNoOfLocalCongestions
National_RNC_P5MD
UniSaalTp
Transport - RNC
pmNoOfNoResponses
No
UniSaalTp
Transport - RNC
pmNoOfOtherErrors
No
UniSaalTp
Transport - RNC
pmNoOfProtocolErrors
No
UniSaalTp
Transport - RNC
pmNoOfReceivedSDUs
No
UniSaalTp
Transport - RNC
pmNoOfRemoteCongestions
No
UniSaalTp
Transport - RNC
pmNoOfSentSDUs
No
UniSaalTp
Transport - RNC
pmNoOfSequenceDataLosses
No
UniSaalTp
Transport - RNC
pmNoOfUnsuccReTransmissions
No
UplinkBaseBandPool
Site
pmApomcOfRakeRecUsed
No
UplinkBaseBandPool
Site
pmApomcOfUlLinkCap
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmHwCePoolEul
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoOfIbho
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoOfRadioLinksSf128
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoOfRadioLinksSf16
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoOfRadioLinksSf256
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoOfRadioLinksSf32
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoOfRadioLinksSf4
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoOfRadioLinksSf64
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoOfRadioLinksSf8
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmNoUlHwLimitEul
National_Site_P5MD
Dimensioning
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 129 of 170
© 2007 AT&T
Troubleshooting
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UplinkBaseBandPool
Site
pmSetupAttemptsSf128
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupAttemptsSf16
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupAttemptsSf256
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupAttemptsSf32
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupAttemptsSf4
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupAttemptsSf64
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupAttemptsSf8
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupFailuresSf128
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupFailuresSf16
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupFailuresSf256
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupFailuresSf32
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupFailuresSf4
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupFailuresSf64
National_Site_P5MD
Dimensioning
UplinkBaseBandPool
Site
pmSetupFailuresSf8
National_Site_P5MD
Dimensioning
Ura
RNC
pmCnInitPagingToUraUe
No
Add when URA is GA
Ura
RNC
pmSamplesRabUra
No
Add when URA is GA
Ura
RNC
pmSumRabUra
No
Add when URA is GA
Ura
RNC
pmUtranInitPagingToUraUe
No
Add when URA is GA
UtranCell
Cell
pmCellDowntimeAuto
Primary Scanner
Primary Scanner
UtranCell
Cell
pmCellDowntimeMan
Primary Scanner
Primary Scanner
UtranCell
Cell
pmChSwitchAttemptFachUra
No
Add when URA is GA
UtranCell
Cell
pmChSwitchAttemptUraFach
No
Add when URA is GA
UtranCell
Cell
pmChSwitchDch128Fach
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchDch384Fach
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchDch64Fach
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchFachDch
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchFachIdle
Primary Scanner
Primary Scanner
UtranCell
Cell
pmChSwitchP128P384
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchP128P64
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchP384P128
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchP64P128
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchSp0Sp64
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchSp64Sp0
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmChSwitchSuccFachUra
No
Add when URA is GA
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 130 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
Cell
UtranCell
Cell
pmChSwitchSuccUraFach
No
Add when URA is GA
pmCmAttDlHls
National_RNC_P5MD
UtranCell
Troubleshooting
Cell
pmCmAttDlSf2
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmCmAttUlHls
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmCmAttUlSf2
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmCmStop
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmCmSuccDlHls
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmCmSuccDlSf2
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmCmSuccUlHls
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmCmSuccUlSf2
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmDlRlcUserPacketThp
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmDlTrafficVolumeAmr4750
No
Add when Multirate AMR is GA
UtranCell
Cell
pmDlTrafficVolumeAmr5900
No
Add when Multirate AMR is GA
UtranCell
Cell
pmDlTrafficVolumeAmr7950
No
Add when Multirate AMR is GA
UtranCell
Cell
pmDlTrafficVolumeCs12
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmDlTrafficVolumeCs57
No
UtranCell
Cell
pmDlTrafficVolumeCs64
No
UtranCell
Cell
pmDlTrafficVolumePs128
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmDlTrafficVolumePs384
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmDlTrafficVolumePs64
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmDlTrafficVolumePs8
No
Add when Streaming QoS is GA
UtranCell
Cell
pmDlTrafficVolumePsCommon
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmDlTrafficVolumePsStr128
No
Add when Streaming QoS is GA
UtranCell
Cell
pmDlTrafficVolumePsStr16
No
Add when Streaming QoS is GA
UtranCell
Cell
pmDlTrafficVolumePsStr64
No
Add when Streaming QoS is GA
UtranCell
Cell
pmDlUpswitchAttemptHigh
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmDlUpswitchAttemptHs
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmDlUpswitchAttemptLow
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmDlUpswitchAttemptMedium
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmDlUpswitchSuccessHigh
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmDlUpswitchSuccessHs
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmDlUpswitchSuccessLow
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmDlUpswitchSuccessMedium
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmDownSwitchAttempt
Secondary Scanner
Secondary Scanner
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 131 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
Cell
pmDownSwitchSuccess
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmEnableEulHhoAttempt
No
UtranCell
Cell
pmEnableEulHhoSuccess
No
UtranCell
Cell
pmEnableHsHhoAttempt
No
UtranCell
Cell
pmEnableHsHhoSuccess
No
UtranCell
Cell
pmEnableHsHhoSuccess
No
UtranCell
Cell
pmEulHarqTransmTti10Failure
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmEulHarqTransmTti10PsInteractive
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmEulHarqTransmTti10Srb
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmEulMacesPduTti10DelivPsInteractive
No
UtranCell
Cell
pmEulMacesPduTti10DelivSrb
No
UtranCell
Cell
pmEulMacesPduTti10UndelivPsInteractive
No
UtranCell
Cell
pmEulMacesPduTti10UndelivSrb
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmEulToDchAttempt
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmEulToDchSuccess
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmFailedChSwitch
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmFailedDchChSwitch
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmFaultyTransportBlocksBcUl
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmHsToDchAttempt
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmHsToDchSuccess
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmInactivityMultiPsInt
No
UtranCell
Cell
pmInactivityPsStreamIdle
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmInterFreqMeasCmStart
National_RNC_P5MD
Troubleshooting - IF
UtranCell
Cell
pmInterFreqMeasCmStop
National_RNC_P5MD
Troubleshooting - IF
UtranCell
Cell
pmInterFreqMeasNoCmStart
National_RNC_P5MD
Troubleshooting - IF
UtranCell
Cell
pmInterFreqMeasNoCmStop
National_RNC_P5MD
Troubleshooting - IF
UtranCell
Cell
pmIratHoGsmMeasCmStart
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmIratHoGsmMeasNoCmStart
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoCellDchDisconnectAbnorm
Secondary Scanner
Secondary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoCellDchDisconnectNormal
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoCellFachDisconnectAbnorm
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoCellFachDisconnectNormal
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoCellUpdAttempt
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoCellUpdSuccess
Secondary Scanner
Secondary Scanner
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 132 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
Cell
pmNoCs64DchDiscAbnorm
Secondary Scanner
Secondary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoCs64DchDiscNormal
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoCsStreamDchDiscAbnorm
Primary Scanner
Primary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoCsStreamDchDiscNormal
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoDirRetryAtt
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoDirRetrySuccess
Secondary Scanner
Secondary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoDlChCodeAllocAltCodeCm
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoDlChCodeAllocAttemptCm
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoEulCcAttempt
No
UtranCell
Cell
pmNoEulCcSuccess
No
UtranCell
Cell
pmNoEulHardHoReturnOldChSource
No
UtranCell
Cell
pmNoEulHardHoReturnOldChTarget
No
UtranCell
Cell
pmNoFailedAfterAdm
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoFailedRabEstAttemptExceedConnLimit
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoFailedRabEstAttemptLackDlAse
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoFailedRabEstAttemptLackDlChnlCode
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoFailedRabEstAttemptLackDlHw
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoFailedRabEstAttemptLackDlHwBest
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoFailedRabEstAttemptLackDlPwr
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoFailedRabEstAttemptLackUlAse
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoFailedRabEstAttemptLackUlHw
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoFailedRabEstAttemptLackUlHwBest
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoHsCcAttempt
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoHsCcSuccess
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoHsHardHoReturnOldChSource
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoHsHardHoReturnOldChTarget
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoIncomingEulHardHoAttempt
No
UtranCell
Cell
pmNoIncomingEulHardHoSuccess
No
UtranCell
Cell
pmNoIncomingHsHardHoAttempt
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoIncomingHsHardHoSuccess
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoInCsIratHoAdmFail
No
Add when 2G to 3G HO is GA
UtranCell
Cell
pmNoInCsIratHoAtt
No
Add when 2G to 3G HO is GA
UtranCell
Cell
pmNoInCsIratHoSuccess
No
Add when 2G to 3G HO is GA
UtranCell
Cell
pmNoLoadSharingRrcConn
Primary Scanner
Primary Scanner
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 133 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
UtranCell
Cell
pmNoLoadSharingRrcConnCs
No
UtranCell
Cell
pmNoLoadSharingRrcConnPs
No
UtranCell
Cell
pmNoNonServingCellReqDeniedEul
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoNormalRabReleaseAmrNb
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoNormalRabReleaseCs64
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoNormalRabReleaseCsStream
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoNormalRabReleasePacket
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoNormalRabReleasePacketStream
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoNormalRabReleasePacketStream128
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoNormalRabReleasePacketUra
No
Add when URA is GA
UtranCell
Cell
pmNoNormalRabReleaseSpeech
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoNormalRbReleaseEul
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoNormalRbReleaseHs
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoOfIurSwDownNgCong
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOfIurTermCsCong
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOfIurTermHsCong
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOfIurTermSpeechCong
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOfNonHoReqDeniedCs
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoOfNonHoReqDeniedEul
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOfNonHoReqDeniedHs
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoOfNonHoReqDeniedInteractive
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoOfNonHoReqDeniedPsStr128
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoOfNonHoReqDeniedPsStreaming
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoOfNonHoReqDeniedSpeech
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoOfReturningEmergencyCalls
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoOfReturningRrcConn
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoOfRlForDriftingUes
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoOfRlForNonDriftingUes
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoOfSampAseDl
Secondary Scanner
Secondary Scanner - Dimensioning
UtranCell
Cell
pmNoOfSampAseUl
Secondary Scanner
Secondary Scanner - Dimensioning
UtranCell
Cell
pmNoOfSwDownEulCong
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOfSwDownHsCong
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOfSwDownNgAdm
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoOfSwDownNgCong
National_RNC_P5MD
Dimensioning
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 134 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
UtranCell
Cell
pmNoOfSwDownNgHo
National_RNC_P5MD
Troubleshooting
Cell
pmNoOfTermCsCong
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOfTermSpeechCong
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoOutgoingEulHardHoAttempt
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoOutgoingEulHardHoSuccess
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoOutgoingHsHardHoAttempt
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoOutgoingHsHardHoSuccess
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoPacketDchDiscAbnorm
Secondary Scanner
Secondary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoPacketDchDiscNormal
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoPagingAttemptCnInitDcch
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoPagingAttemptUtranRejected
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoPagingType1Attempt
No
UtranCell
Cell
pmNoPagingType1AttemptCs
No
UtranCell
Cell
pmNoPagingType1AttemptPs
No
UtranCell
Cell
pmNoPsStream128Ps8DchDiscAbnorm
No
Add when Streaming QoS is GA
UtranCell
Cell
pmNoPsStream128Ps8DchDiscNormal
No
Add when Streaming QoS is GA
UtranCell
Cell
pmNoPsStream64Ps8DchDiscAbnorm
Primary Scanner
Primary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoPsStream64Ps8DchDiscNormal
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoRabEstablishAttemptAmrNb
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoRabEstablishAttemptCs57
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishAttemptCs64
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishAttemptPacketInteractive
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishAttemptPacketInteractiveEul
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoRabEstablishAttemptPacketInteractiveHs
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishAttemptPacketStream
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishAttemptPacketStream128
Primary Scanner
UtranCell
Cell
pmNoRabEstablishAttemptSpeech
Primary Scanner
UtranCell
Cell
pmNoRabEstablishSuccessAmrNb
National_RNC_P5MD
Primary Scanner - Level 1 and 3 Scorecard
Primary Scanner - Level 1 and 3 Scorecard
and Dimensioning
Troubleshooting
UtranCell
Cell
pmNoRabEstablishSuccessCs57
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishSuccessCs64
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishSuccessPacketInteractive
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishSuccessPacketInteractiveEul
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoRabEstablishSuccessPacketInteractiveHs
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoRabEstablishSuccessPacketStream
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 135 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
Cell
pmNoRabEstablishSuccessPacketStream128
Primary Scanner
UtranCell
Cell
pmNoRabEstablishSuccessSpeech
Primary Scanner
UtranCell
Cell
pmNoRejRrcConnMpLoadC
Secondary Scanner
Primary Scanner - Level 1 and 3 Scorecard
Primary Scanner - Level 1 and 3 Scorecard
and Dimensioning
Secondary Scanner
UtranCell
Cell
pmNoReqDeniedAdm
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoRlDeniedAdm
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoRrcCsReqDeniedAdm
Primary Scanner
Dimensioning
UtranCell
Cell
pmNoRrcPsReqDeniedAdm
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoRrcReqDeniedAdm
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoServingCellReqDeniedEul
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoSpeechDchDiscAbnorm
Secondary Scanner
Secondary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoSpeechDchDiscNormal
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoSysRelSpeechNeighbr
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoSysRelSpeechSoHo
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoSysRelSpeechUlSynch
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoSystemRabReleaseAmrNb
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoSystemRabReleaseCs64
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoSystemRabReleaseCsStream
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoSystemRabReleasePacket
Primary Scanner
Primary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoSystemRabReleasePacketStream
Primary Scanner
Primary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoSystemRabReleasePacketStream128
Primary Scanner
Primary Scanner - Level 3 Scorecard
UtranCell
Cell
pmNoSystemRabReleasePacketUra
No
Add when URA is GA
UtranCell
Cell
pmNoSystemRabReleaseSpeech
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmNoSystemRbReleaseEul
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmNoSystemRbReleaseHs
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoTimesCellFailAddToActSet
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoTimesIfhoCellFailAddToActSet
National_RNC_P5MD
Troubleshooting - IF
UtranCell
Cell
pmNoTimesIfhoRlAddToActSet
National_RNC_P5MD
Troubleshooting - IF
UtranCell
Cell
pmNoTimesRlAddToActSet
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoTimesRlDelFrActSet
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoTimesRlRepInActSet
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmNoTpSwitchSp64Speech
Primary Scanner
Primary Scanner
UtranCell
Cell
pmNoUraUpdAttempt
No
Add when URA is GA
UtranCell
Cell
pmNoUraUpdSuccess
No
Add when URA is GA
UtranCell
Cell
pmRabEstablishEcAttempt
National_RNC_P5MD
Troubleshooting
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 136 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
Cell
pmRabEstablishEcSuccess
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRes1
Activated by RES Recording
Level 3 Scorecard
UtranCell
Cell
pmRes2
Activated by RES Recording
Level 3 Scorecard
UtranCell
Cell
pmRes3
Activated by RES Recording
Level 3 Scorecard
UtranCell
Cell
pmRes4
Activated by RES Recording
Level 3 Scorecard
UtranCell
Cell
pmRes5
Activated by RES Recording
Level 3 Scorecard
UtranCell
Cell
pmRes6
Activated by RES Recording
Level 3 Scorecard
UtranCell
Cell
pmRlAddAttemptsBestCellCsConvers
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddAttemptsBestCellPacketHigh
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddAttemptsBestCellPacketLow
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddAttemptsBestCellSpeech
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddAttemptsBestCellStandAlone
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddAttemptsBestCellStream
No
Add when Streaming QoS is GA
UtranCell
Cell
pmRlAddSuccessBestCellCsConvers
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddSuccessBestCellPacketHigh
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddSuccessBestCellPacketLow
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddSuccessBestCellSpeech
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddSuccessBestCellStandAlone
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmRlAddSuccessBestCellStream
No
Add when Streaming QoS is GA
UtranCell
Cell
pmSamplesActDlRlcTotPacketThp
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesActDlRlcUserPacketThp
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesActUlRlcTotPacketThp
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesActUlRlcUserPacketThp
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesAmr12200RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSamplesAmr4750RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSamplesAmr5900RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSamplesAmr7950RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSamplesBestAmr12200RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSamplesBestAmr4750RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSamplesBestAmr5900RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSamplesBestAmr7950RabEstablish
No
UtranCell
Cell
pmSamplesBestCs12Establish
Primary Scanner
UtranCell
Cell
pmSamplesBestCs12PsIntRabEstablish
Secondary Scanner
Add when Multirate AMR is GA
Primary Scanner - Level 3 Scorecard and
Dimensioning
Secondary Scanner
UtranCell
Cell
pmSamplesBestCs57RabEstablish
Primary Scanner
Primary Scanner
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 137 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
Cell
pmSamplesBestCs64PsIntRabEstablish
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmSamplesBestCs64RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesBestDchPsIntRabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesBestPsEulRabEstablish
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmSamplesBestPsHsAdchRabEstablish
Primary Scanner
Dimensioning
UtranCell
Cell
pmSamplesBestPsStr128Ps8RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesBestPsStr64Ps8RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesCompMode
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesCs12Ps0RabEstablish
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesCs12Ps64RabEstablish
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesCs12RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesCs57RabEstablish
No
UtranCell
Cell
pmSamplesCs64Ps8RabEstablish
Secondary Scanner
UtranCell
Cell
pmSamplesCs64RabEstablish
No
UtranCell
Cell
pmSamplesFachPsIntRabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesPsEulRabEstablish
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmSamplesPsHsAdchRabEstablish
Secondary Scanner
Secondary Scanner - Dimensioning
UtranCell
Cell
pmSamplesPsInteractive
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSamplesPsStr128Ps8RabEstablish
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmSamplesPsStr64Ps8RabEstablish
No
UtranCell
Cell
pmSamplesRabFach
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesRrcOnlyEstablish
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmSamplesUesWith1Rls1RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUesWith1Rls2RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUesWith1Rls3RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUesWith2Rls2RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUesWith2Rls3RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUesWith2Rls4RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUesWith3Rls3RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUesWith3Rls4RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUesWith4Rls4RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSamplesUlRssi
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmSumActDlRlcTotPacketThp
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumActDlRlcUserPacketThp
Primary Scanner
Primary Scanner
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 138 of 170
© 2007 AT&T
Secondary Scanner
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
Cell
pmSumActUlRlcTotPacketThp
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumActUlRlcUserPacketThp
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumAmr12200RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSumAmr4750RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSumAmr5900RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSumAmr7950RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSumBestAmr12200RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSumBestAmr4750RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSumBestAmr5900RabEstablish
No
Add when Multirate AMR is GA
UtranCell
Cell
pmSumBestAmr7950RabEstablish
No
UtranCell
Cell
pmSumBestCs12Establish
Primary Scanner
UtranCell
Cell
pmSumBestCs12PsIntRabEstablish
Secondary Scanner
Add when Multirate AMR is GA
Primary Scanner - Level 3 Scorecard and
Dimensioning
Secondary Scanner
UtranCell
Cell
pmSumBestCs57RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumBestCs64PsIntRabEstablish
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmSumBestCs64RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumBestDchPsIntRabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumBestPsEulRabEstablish
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmSumBestPsHsAdchRabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumBestPsStr128Ps8RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumBestPsStr64Ps8RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumCompMode
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumCs12Ps0RabEstablish
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumCs12Ps64RabEstablish
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumCs12RabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumCs57RabEstablish
No
UtranCell
Cell
pmSumCs64Ps8RabEstablish
Secondary Scanner
UtranCell
Cell
pmSumCs64RabEstablish
No
UtranCell
Cell
pmSumFachPsIntRabEstablish
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumOfSampAseDl
Secondary Scanner
Secondary Scanner - Dimensioning
UtranCell
Cell
pmSumOfSampAseUl
Secondary Scanner
Secondary Scanner - Dimensioning
UtranCell
Cell
pmSumOfTimesMeasOlDl
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmSumOfTimesMeasOlUl
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmSumPsEulRabEstablish
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmSumPsHsAdchRabEstablish
Secondary Scanner
Secondary Scanner - Dimensioning
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 139 of 170
© 2007 AT&T
Secondary Scanner
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
UtranCell
Cell
pmSumPsInteractive
Primary Scanner
Primary Scanner
UtranCell
Cell
pmSumPsStr128Ps8RabEstablish
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmSumPsStr64Ps8RabEstablish
No
UtranCell
Cell
pmSumRabFach
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumRrcOnlyEstablish
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmSumUesWith1Rls1RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUesWith1Rls2RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUesWith1Rls3RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUesWith2Rls2RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUesWith2Rls3RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUesWith2Rls4RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUesWith3Rls3RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUesWith3Rls4RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUesWith4Rls4RlInActSet
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmSumUlRssi
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotalTimeDlCellCong
Primary Scanner
Primary Scanner
UtranCell
Cell
pmTotalTimeUlCellCong
Primary Scanner
Primary Scanner
UtranCell
Cell
pmTotNoRrcConnectAttIratCcOrder
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotNoRrcConnectAttIratCellResel
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotNoRrcConnectFailCongIratCcOrder
No
UtranCell
Cell
pmTotNoRrcConnectFailCongIratCellResel
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmTotNoRrcConnectReq
Primary Scanner
Primary Scanner - Dimensioning
UtranCell
Cell
pmTotNoRrcConnectReqCs
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmTotNoRrcConnectReqCsSucc
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmTotNoRrcConnectReqPs
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmTotNoRrcConnectReqPsSucc
Primary Scanner
Primary Scanner - Level 1 and 3 Scorecard
UtranCell
Cell
pmTotNoRrcConnectReqSms
National_RNC_P5MD
UtranCell
Cell
pmTotNoRrcConnectReqSuccess
Primary Scanner
UtranCell
Cell
pmTotNoRrcConnectSuccessIratCcOrder
National_RNC_P5MD
Dimensioning
Primary Scanner - Level 3 Scorecard and
Dimensioning
Troubleshooting
UtranCell
Cell
pmTotNoRrcConnectSuccessIratCellResel
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotNoTermRrcConnectReq
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotNoTermRrcConnectReqCs
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotNoTermRrcConnectReqCsSucc
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotNoTermRrcConnectReqPs
National_RNC_P5MD
Troubleshooting
ND-00150
Rev. 3.0 09/09/2007
Active within scanner
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 140 of 170
© 2007 AT&T
Reason
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Reason
UtranCell
Cell
pmTotNoTermRrcConnectReqPsSucc
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotNoTermRrcConnectReqSucc
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmTotNoUtranRejRrcConnReq
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmTransportBlocksBcUl
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmUlRlcUserPacketThp
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmUlTrafficVolumeAmr4750
No
Add when Multirate AMR is GA
UtranCell
Cell
pmUlTrafficVolumeAmr5900
No
Add when Multirate AMR is GA
UtranCell
Cell
pmUlTrafficVolumeAmr7950
No
Add when Multirate AMR is GA
UtranCell
Cell
pmUlTrafficVolumeCs12
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmUlTrafficVolumeCs57
No
UtranCell
Cell
pmUlTrafficVolumeCs64
No
UtranCell
Cell
pmUlTrafficVolumePs128
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmUlTrafficVolumePs384
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmUlTrafficVolumePs64
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmUlTrafficVolumePs8
No
UtranCell
Cell
pmUlTrafficVolumePsCommon
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmUlTrafficVolumePsStr128
No
Add when Streaming QoS is GA
UtranCell
Cell
pmUlTrafficVolumePsStr16
No
Add when Streaming QoS is GA
UtranCell
Cell
pmUlUpswitchAttemptEul
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmUlUpswitchAttemptHigh
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmUlUpswitchAttemptLow
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmUlUpswitchAttemptMedium
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmUlUpswitchSuccessEul
National_RNC_P5MD
Troubleshooting
UtranCell
Cell
pmUlUpswitchSuccessHigh
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmUlUpswitchSuccessLow
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmUlUpswitchSuccessMedium
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmUpswitchFachHsAttempt
Secondary Scanner
Secondary Scanner
UtranCell
Cell
pmUpswitchFachHsSuccess
Secondary Scanner
Secondary Scanner
UtranRelation
Inter-Freq
pmAttNonBlindInterFreqHoCsConversational
No
UtranRelation
Inter-Freq
pmAttNonBlindInterFreqHoCsSpeech12
No
UtranRelation
Inter-Freq
pmAttNonBlindInterFreqHoPsInteractiveGreater64
No
UtranRelation
Inter-Freq
pmAttNonBlindInterFreqHoPsInteractiveLess64
No
UtranRelation
Inter-Freq
pmAttNonBlindInterFreqHoStreamingOther
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoFailRevertCsConversational
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 141 of 170
© 2007 AT&T
Add when Streaming QoS is GA
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoFailRevertCsSpeech12
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoFailRevertPsInteractiveGreater64
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoFailRevertPsInteractiveLess64
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoFailRevertStreamingOther
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoRevertCsConversational
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoRevertCsSpeech12
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoRevertPsInteractiveGreater64
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoRevertPsInteractiveLess64
No
UtranRelation
Inter-Freq
pmFailNonBlindInterFreqHoRevertStreamingOther
No
Add when Streaming QoS is GA
UtranRelation
CNHHO
pmNoAttOutCnhhoCsNonSpeech
No
Add when CNHHO is GA
UtranRelation
CNHHO
pmNoAttOutCnhhoPsConnRelease
No
Add when CNHHO is GA
UtranRelation
CNHHO
pmNoAttOutCnhhoSpeech
No
Add when CNHHO is GA
UtranRelation
CNHHO
pmNoSuccOutCnhhoCsNonSpeech
No
Add when CNHHO is GA
UtranRelation
CNHHO
pmNoSuccOutCnhhoSpeech
No
Add when CNHHO is GA
UtranRelation
Intra-Freq
pmRlAddAttemptsBestCellCsConvers
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddAttemptsBestCellPacketHigh
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddAttemptsBestCellPacketLow
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddAttemptsBestCellSpeech
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddAttemptsBestCellStandAlone
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddAttemptsBestCellStream
No
Add when Streaming QoS is GA
UtranRelation
Intra-Freq
pmRlAddSuccessBestCellCsConvers
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddSuccessBestCellPacketHigh
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddSuccessBestCellPacketLow
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddSuccessBestCellSpeech
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddSuccessBestCellStandAlone
National_URel_P5MD
Troubleshooting
UtranRelation
Intra-Freq
pmRlAddSuccessBestCellStream
No
Add when Streaming QoS is GA
UtranRelation
Inter-Freq
pmSuccNonBlindInterFreqHoCsConversational
No
UtranRelation
Inter-Freq
pmSuccNonBlindInterFreqHoCsSpeech12
No
UtranRelation
Inter-Freq
pmSuccNonBlindInterFreqHoPsInteractiveGreater64
No
UtranRelation
Inter-Freq
pmSuccNonBlindInterFreqHoPsInteractiveLess64
No
UtranRelation
Inter-Freq
pmSuccNonBlindInterFreqHoStreamingOther
No
Vc12Ttp
Transport
pmVcBbe
No
Vc12Ttp
Transport
pmVcEs
No
Vc12Ttp
Transport
pmVcSes
No
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 142 of 170
© 2007 AT&T
Reason
Add when Streaming QoS is GA
Add when Streaming QoS is GA
Volume II – Ericsson Field Guide for UTRAN P3
MO Class
Resolution
Counter
Active within scanner
Vc12Ttp
Transport
pmVcUas
No
Vc4Ttp
Transport
pmVcBbe
No
Vc4Ttp
Transport
pmVcEs
No
Vc4Ttp
Transport
pmVcSes
No
Vc4Ttp
Transport
pmVcUas
No
VclTp
Transport - RNC
pmReceivedAtmCells
National_RNC_P5MD
Dimensioning
VclTp
Transport - RNC
pmTransmittedAtmCells
National_RNC_P5MD
Dimensioning
VpcTp
Transport - RNC
pmBwErrBlocks
No
VpcTp
Transport - RNC
pmBwLostCells
No
VpcTp
Transport - RNC
pmBwMissinsCells
No
VpcTp
Transport - RNC
pmFwErrBlocks
No
VpcTp
Transport - RNC
pmFwLostCells
National_RNC_P5MD
VpcTp
Transport - RNC
pmFwMissinsCells
No
VpcTp
Transport - RNC
pmLostBrCells
National_RNC_P5MD
Troubleshooting
VpcTp
Transport - RNC
pmLostFpmCells
National_RNC_P5MD
Troubleshooting
VplTp
Transport - RNC
pmReceivedAtmCells
National_RNC_P5MD
Dimensioning
VplTp
Transport - RNC
pmTransmittedAtmCells
National_RNC_P5MD
Dimensioning
Vt15Ttp
Transport
pmEs
No
Vt15Ttp
Transport
pmSes
No
Vt15Ttp
Transport
pmUas
No
UtranCell
Cell
pmNoRabEstBlockTnSpeechBest
National_RNC_P5MD
Dimensioning
UtranCell
Cell
pmNoRabEstBlockTnPsIntNonHsBest
National_RNC_P5MD
Dimensioning
.
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 143 of 170
© 2007 AT&T
Reason
Troubleshooting
Volume II – Ericsson Field Guide for UTRAN P3
2.
Recording Activation
As needed, WCDMA Measurement Result Recordings (WMRR) will be specified in this section. Only one
RES recording can be run on a given RNC at a time. As well, this recording occupies the maximum number
of measurements configurable in an RES recording.
1.
Activation of RES Recording to support Scorecard Data
This recording specifies activation of a Radio Environment Statistics (RES) recording that will cause the
RNS to command UEs to send periodic Speech BLER measurements. The Tektronix Probes will collect
these measurements for use in the Scorecard.
Activation of this recording will cause a command to be sent to 50% of the Speech calls established in
each RNC. These UEs will then report UL and DL Speech BLER for Speech Only, R99 MultiRAB and HS
MultiRAB calls.

Recording Name: RES test for Tek Probes 50% of UEs

Start date 2007-01-17 (today’s date)

Repeat: Daily – 365 times

Hours 03:20 - 23:35

Cell Set: Click “Select Cells…”, click the target RNC, then click “Copy RNCs…”

Measurements:


Service 1 = Speech DL BLER

Service 2 = Speech UL BLER

Service 3 = Speech + Interactive DL BLER

Service 4 = Speech + Interactive UL BLER

Service 5 = Speech + InteractiveHS DL BLER

Service 6 = Speech + InteractiveHS UL BLER
Click “Sample and Fraction Settings”


ND-00150
Rev. 3.0 09/09/2007
Select 2 seconds for “All Speech Dependent Services
For the “UE Fraction” select “1/2”. Click OK
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 144 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
8. Reference Documents
The following documents are related to this document:
1. ALEX Documentation located at http://manchild.wireless.attws.com/cgi-bin/alex
a. WCDMA RAN P5 (CXS 101 06/5 R6A)
b. WCDMA RNC 3810 P5
c.
Operations Support System (OSS) RC R4, AOM 901 017/4, R1M/4 (C3)
d. WCDMA RBS 3106 P5 (CXP 901 1612/2 R3B)
e. WCDMA RBS 3206 P5 (CXP 901 1612/2 R3B)
f.
WCDMA RBS 3303 P5 (CXP 901 1612/2 R3B; CXP 901 1612/1 R3B)
2. 3GPP Specification http://www.3gpp.org
a. R6 TS 25.101 Clause 5 – Frequency Bands and channel arrangement
b. R6 TS 25.101 Clause 6.2.1 – UE maximum output power
c.
R6 TS 25.101 Clause 7 – UE Receiver Characteristics
d. R6 TS 25.104 Clause 7 – Node B Receiver Characteristics
e. R6 TS 25.214 Annex C – Cell Search Procedure
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 145 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
9. Parameter Reference
The following tables provide parameter ranges and default values involved in getting the UE into Idle Mode, Establishing a Call and Maintaining
Mobility and Connectivity. They are listed in the same order they were presented. The Level column indicates the network element that owns the
parameter. The class column indicates if the parameter is set based on Policy (must be set this way), Rule (must be set this way with
exceptions), Fixed (recommended to be set this way) and Variable (set at your discretion).
Table 20: Configurable Parameter Lookup Table
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
uarfcnDl
See section 4.1.2
N/A
N/A
Cell
Variable
Integer
uarfcnUl
See section 4.1.2
N/A
N/A
Cell
Variable
Integer
supportOf16qam
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
Cell
Fixed
Integer
primaryScramblingCode
0 to 511
N/A
0 to 511
Cell
Variable
Integer
-100 to +500
300
300
Cell
Fixed
0.1dBm
primarySchPower
-350 to +150
-18
-18
Cell
Fixed
0.1dB
secondarySchPower
-350 to +150
-35
-35
Cell
Fixed
0.1dB
bchPower
-350 to +150
-31
-31
Cell
Fixed
0.1dB
noOfMibValueTagRetrans
0 to 10
0
0
RNC
Fixed
Retransmissions
sib1PLMNScopeValueTag
0 to 31
N/A
0 to 31
Cell
Variable
Integer
mcc
0 to 999
1
310
RNC
Fixed
Integer
mnc
0 to 999
N/A
410
RNC
Fixed
Integer
sib1StartPos
0 to 4094
4
4
RNC
Fixed
Frames
sib1RepPeriod
4, 8, 16 to 4096
32
32
RNC
Fixed
Frames
sib3StartPos
0 to 4094
2
2
RNC
Fixed
Frames
sib3RepPeriod
4, 8, 16 to 4096
16
16
RNC
Fixed
Frames
sib5StartPos
0 to 4094
6
6
RNC
Fixed
Frames
sib5RepPeriod
4, 8, 16 to 4096
32
32
RNC
Fixed
Frames
sib7StartPos
0 to 4094
2
2
RNC
Fixed
Frames
sib7RepPeriod
4, 8, 16 to 4096
16
16
RNC
Fixed
Frames
sib7expirationTimeFactor
1, 2, 4, 8 to 256
1
1
RNC
Fixed
Factor
sib11StartPos
0 to 4094
20
20
RNC
Fixed
Frames
sib11RepPeriod
4, 8, 16 to 4096
128
128
RNC
Fixed
Frames
Basic Design Requirements
primaryCpichPower
Idle Mode
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 146 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
sib12StartPos
0 to 4094
14
14
RNC
Fixed
Frames
sib12RepPeriod
4, 8, 16 to 4096
32
32
RNC
Fixed
Frames
nmo
Mode 1 or 2
2
2
RA
Fixed
Integer
cellReserved
RESERVED or NOT_RESERVED
NOT_RESERVED
NOT_RESERVED
Cell
Variable
String
accessClassNbarred
0 to 65535
0
0
Cell
Fixed
Integer
qRxLevMin
-115 to -25
-115
-115
Cell
Fixed
dBm
maxTxPowerUl
-50 to +33
24
24
Cell
Fixed
dBm
qQualMin
-24 to 0
-18
-19
Cell
Fixed
dB
att
0=FALSE, 1=TRUE
1=TRUE
1=TRUE
LA
Fixed
Integer
aichPower
-22 to +5
-6
-6
Cell
Fixed
dB
ConstantValueCprach
-35 to -10
-27
-27
Cell
Fixed
dB
powerOffsetP0
1 to 8
3
2
Cell
Fixed
dB
preambleRetransMax
1 to 64
8
15
Cell
Fixed
Preambles
maxPreambleCycle
1 to 32
4
3
Cell
Fixed
Cycles
powerOffsetPpm
-5 to +10
-4
0
Cell
Fixed
dB
dlInitSirTarget
-82 to 173
41
41
RNC
Fixed
0.1dB
cBackOff
-60 to +60
0
0
RNC
Fixed
0.25dB
ecNoPcpichDefault
-20 to -10
-16
-16
RNC
Fixed
dB
pO2
0 to 24
12
12
RNC
Fixed
0.25dB
pcpichPowerDefault
0 to 50
33
33
RNC
Fixed
dBm
ulInitSirTargetSrb
-82 to 173
57
57
RNC
Fixed
0.1dB
ulInitSirTargetLow
-82 to 173
49
49
RNC
Fixed
0.1dB
ulInitSirTargetHigh
-82 to 173
82
82
RNC
Fixed
0.1dB
ulInitSirTargetExtraHigh
-82 to 173
92
92
RNC
Fixed
0.1dB
cPO
-30 to 30
0
0
RNC
Fixed
0.1dB
lAC
1 to 65533, 65535
N/A
N/A
LA
Variable
Integer
rAC
0 to 255
N/A
N/A
RNC
Variable
Integer
t3212
0 to 255
10
10
LA
Fixed
6minutes
multiRabSp0Available
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
multiRabUdi8Available
0=FALSE, 1=TRUE
0=FALSE
0=FALSE
RNC
Fixed
Binary
psStreaming128
0=FALSE, 1=TRUE
0=FALSE
0=FALSE
RNC
Fixed
Binary
allow384HsRab
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
state128_128Supported
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
pichPower
-10 to +5
-7
-7
Cell
Fixed
dB
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 147 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
pchPower
-350 to 150
-4
cnDrxCycleLengthCs
6 to 9
6=640
-4
RNC
Fixed
0.1dB
7=1280
RNC
Fixed
cnDrxCycleLengthPs
6 to 9
coeff
7=1280
7=1280
RNC
Fixed
utranDrxCycleLength
coeff
3 to 9
5=320
5=320
RNC
Fixed
coeff
noOfPagingRecordTransm
1 to 5
2
2
RNC
Fixed
Integer
noOfMaxDrxCycles
1 to 10
1
1
RNC
Fixed
DRX cycles
hsdpaUsersAdm
0 to 1000
10
10
Cell
Var.
Users
maxNumHsdpaUsers
1 to 32
16
16
Cell
Var.
Users
compModeAdm
0 to 128
15
15
Cell
Var.
Radio Links
eulServingCellUsersAdm
0 to 100
32
4
Cell
Fixed
E-DCH users
eulNonServingCellUsersAdm
0 to 100
100
10
Cell
Fixed
E-DCH users
dlCodeAdm
0 to 100
80
70
Cell
Var.
%
beMarginDlCode
0 to 20
1
1
Cell
Var.
5%
sf8Adm
0 to 8
8
8
Cell
Fixed
Radio Links
sf16Adm
0 to 16
16
16
Cell
Var.
Radio Links
sf32Adm
0 to 32
32
32
Cell
Var.
Radio Links
sf16gAdm
0 to 16
16
16
Cell
Var.
Radio Links
sf16AdmUl
0 to 50
16
50
Cell
Var.
Radio Links
sf8AdmUl
0 to 50
8
8
Cell
Var.
Radio Links
sf4AdmUl
0 to 1000
0
6
Cell
Var.
Radio Links
pwrAdm
0 to 100
75
75
Cell
Var.
%
maximumTransmissionPower
0 to 500
400
400
Cell
Var.
0.1dBm
beMarginDlPwr
0 to 100
10
10
Cell
Var.
%
pwrAdmOffset
0 to 100
10
10
Cell
Var.
%
aseUlAdm
0 to 500
160
500
Cell
Var.
ASE
beMarginAseUl
0 to 500
20
0
Cell
Var.
ASE
aseUlAdmOffset
0 to 500
40
40
Cell
Var.
ASE
aseDlAdm
0 to 500
240
500
Cell
Var.
ASE
beMarginAseDl
0 to 500
100
0
Cell
Var.
ASE
ulHwAdm
0 to 100
100
80
Site
Var.
%
beMarginUlHw
0 to 100
0
0
Site
Var.
%
dlHwAdm
0 to 100
100
100
Site
Var.
%
beMarginDlHw
0 to 100
0
0
Site
Var.
%
Admission Control
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 148 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
emergencyCallRedirect
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
ulPathlossCheckEnabled
TRUE or FALSE
FALSE
FALSE
Cell
Var.
String
sf4UlPathlossThreshold
15 to 170
170
170
Cell
Var.
dB
loadSharingDirRetryEnabled
0=FALSE, 1=TRUE
0=FALSE
0=FALSE
RNC
Fixed
Binary
loadSharingGsmThreshold
0 to 100
75
100
Cell
Fixed
%
loadSharingGsmFraction
0 to 100
100
100
Cell
Fixed
%
directedRetryTarget
2G Neighbor
N/A
N/A
Cell
Var.
N/A
loadSharingRrcEnabled
0=FALSE, 1=TRUE
0=FALSE
0=FALSE
RNC
Fixed
Binary
loadSharingMargin
0 to 100
0
0
Cell
Fixed
%
loadSharingCandidate
3G Neighbor
N/A
N/A
Nabr
Var.
N/A
hsOnlyBestCell
0=FALSE, 1=TRUE
1=TRUE
1=TRUE
RNC
Fixed
Binary
packetEstMode
0, 1 or 2
1
1
RNC
Fixed
Integer
activeQueueMgmt
0=OFF, 1=ON
0=OFF
0=OFF
RNC
Fixed
Binary
sIntraSearch
0=Continually, 1 to 27
0
22=10
Cell
Fixed
dB
sInterSearch
0=Continually, 1 to 27
0
0
Cell
Fixed
dB
sRatSearch
-32 to 20
4
4
Cell
Fixed
dB
sHcsRat
-105 to 91
-105
-105
Cell
Fixed
dB
interFreqFddMeasIndicator
0=FALSE, 1=TRUE
0=FALSE
0=FALSE
Cell
Fixed
Binary
fachMeasOccaCycLenCoeff
0 to 12
0
4
Cell
Fixed
Integer
qualMeasQuantity
1=CPICH_RSCP or 2=CPICH_EC_NO
2=CPICH_EC_NO
2=CPICH_EC_NO
Cell
Fixed
String
qHyst1
0 to 40
4
2
Cell
Fixed
dB
qHyst2
0 to 40
4
2
Cell
Fixed
dB
qOffset1sn(UtranRelation)
-50 to 50
0
0
Nabr
Fixed
dB
qOffset1sn(GsmRelation)
-50 to 50
7
7
Nabr
Fixed
dB
qOffset2sn
-50 to 50
0
0
Nabr
Fixed
dB
treSelection
0 to 31
2
1
Cell
Fixed
seconds
Call Establishment Related
Cell Reselection
Intra-Frequency Handover
reportingRange1a
0 to 29
6
6
RNC
Fixed
0.5dB
hysteresis1a
0 to 15
0
0
RNC
Fixed
0.5dB
timeToTrigger1a
0 to 15
11=320
11=320
RNC
Fixed
ms
maxActiveSet
2 to 4
3
3
RNC
Fixed
Radio Links
releaseConnOffset
-30 to 120
120
120
RNC
Fixed
0.1dB
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 149 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
reportingInterval1a
0 to 16
3=1
3=1
measQuantity1
1=CPICH_RSCP or 2=CPICH_EC_NO
2=CPICH_EC_NO
2=CPICH_EC_NO
RNC
Fixed
seconds
Cell
Fixed
reportingRange1b
0 to 29
10
String
10
RNC
Fixed
hysteresis1b
0 to 15
0.5dB
0
0
RNC
Fixed
timeToTrigger1b
0.5dB
0 to 15
12=640
12=640
RNC
Fixed
ms
hysteresis1c
0 to 15
2
2
RNC
Fixed
0.5dB
timeToTrigger1c
0 to 15
11=320
11=320
RNC
Fixed
ms
reportingInterval1c
0 to 16
3=1
3=1
RNC
Fixed
seconds
hysteresis1d
0 to 15
15
15
RNC
Fixed
0.5dB
timeToTrigger1d
0 to 15
14=2560
14=2560
RNC
Fixed
ms
filterCoefficient1
0. to 9, 11, 13, 15, 17, 19
2
2
RNC
Fixed
coeff
individualOffset(UtranCell)
-10 to 10
0
0
Cell
Fixed
0.5dB
w1a
0 to 20
0
0
RNC
Fixed
0.1unit
w1b
0 to 20
0
0
RNC
Fixed
0.1unit
Inter-Frequency and Inter-RAT Handover
usedFreqThresh2dEcno(hho)
-24 to 0
-12
-12
Cell
Fixed
dB
hysteresis2d
0 to 29
0
4
RNC
Fixed
0.5 dB
timeToTrigger2dEcno
Various
320
320
RNC
Fixed
ms
usedFreqThresh2dRscp(hho)
-115 to -25
-97
-106 ±4
Cell
Fixed
dBm
timeToTrigger2dRscp
Various
320
320
RNC
Fixed
ms
usedFreqThresh2dEcno(sho)
-24 to 0
-12
-15
Cell
Fixed
dB
usedFreqThresh2dRscp(sho)
-115 to -25
-97
-112
Cell
Fixed
dBm
usedFreqThresh2dEcnoDrnc
-24 to 0
-12
-12
RNC
Fixed
dB
usedFreqThresh2dRscpDrnc
-115 to -25
-97
-106
RNC
Fixed
dBm
usedFreqRelThresh2fEcno
0 to 20
1
2
RNC
Fixed
dB
hysteresis2f
0 to 29
0
2
RNC
Fixed
0.5dB
timeToTrigger2fEcno
Various
1280
640
RNC
Fixed
ms
usedFreqRelThresh2fRscp
0 to 20
3
6
RNC
Fixed
dB
txPowerConnQualMonEnabled
0=FALSE, 1=TRUE
1=TRUE
0=FALSE
RNC
Fixed
Binary
timeToTrigger6d
Various
320
320
RNC
Fixed
ms
ueTxPowerThresh6b
-50 to 33
18
21
RNC
Fixed
dB
timeTrigg6b
Various
1280
1280
RNC
Fixed
ms
filterCoefficient2
0. to 9, 11, 13, 15, 17, 19
2
2
RNC
Fixed
coeff
filterCoeff6
0. to 9, 11, 13, 15, 17, 19
19
3
RNC
Fixed
coeff
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 150 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
usedFreqW2d
0 to 20
0
10
RNC
Fixed
0.1unit
usedFreqW2f
0 to 20
0
10
RNC
Fixed
0.1unit
FddIfHoSupp
0=FALSE, 1=TRUE
0=FALSE
0=FALSE
RNC
Fixed
Binary
FddGsmHoSupp
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
hoType
0=IFHO, 1=GSM, 2=NONE
1
1=GSM_PREFERRED
Cell
Fixed
String
defaultHoType
0=IFHO, 1=GSM, 2=NONE
1
1=GSM_PREFERRED
Cell
Fixed
String
utranRelThresh3aEcno
-10 to 10
-1
2
RNC
Fixed
dB
hysteresis3a
0 to 15
0
4
RNC
Fixed
0.5dB
gsmThresh3a
-115 to 0
-102
-98
RNC
Fixed
dBm
timeToTrigger3a
0 to 15
6=100
6=100
RNC
Fixed
ms
utranRelThresh3aRscp
-20 to 20
-3
7
RNC
Fixed
dB
gsmFilterCoefficient3
0. to 9, 11, 13, 15, 17, 19
1
1
RNC
Fixed
coeff
utranFilterCoefficient3
0. to 9, 11, 13, 15, 17, 19
2
2
RNC
Fixed
coeff
utranW3a
0 to 20
0
10
RNC
Fixed
0.1unit
utranRelThreshRscp
0 to 40
5
5
RNC
Fixed
dB
usedFreqRelThresh4_2bEcno
-10 to 10
-1
-1
RNC
Fixed
dB
hyst4_2b
0 to 75
10
10
RNC
Fixed
0.1dB
nonUsedFreqThresh4_2bEcno
-24 to 0
-11
-13
RNC
Fixed
dB
nonUsedFreqThresh4_2bRscp
-94
-105
RNC
Fixed
dBm
100
100
RNC
Fixed
ms
UsedFreqRelThresh4_2bRscp
-115 to 25
0, 10, 20,40, 60, 80, 100, 120, 160, 200,
240, 320, 640, 1280, 2560, 5000
-20 to 20
-3
-3
RNC
Fixed
dB
timeToTrigger2fRscp
Various
1280
640
RNC
Fixed
ms
filterCoeff4_2b
0. to 9, 11, 13, 15, 17, 19
2
2
RNC
Fixed
coeff
usedFreqW4_2b
0. to 9, 11, 13, 15, 17, 19
0
0
RNC
Fixed
coeff
nonUsedFreqW4_2b
0. to 9, 11, 13, 15, 17, 19
0
0
RNC
Fixed
coeff
timeTrigg4_2b
HS Cell Change
hsQualityEstimate
0=CPICH_EC_NO, 1=CPICH_RSCP
1=RSCP
1=RSCP
RNC
Fixed
Binary
hsHysteresis1d
0 to 75
10
10
RNC
Fixed
0.1dB
hsTimeToTrigger1d
Various
640
640
RNC
Fixed
ms
hsCellChangeAllowed
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
hsToDchTrigger(changeOfBestCellIntraRnc)
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
hsToDchTrigger(servHsChangeIntraRnc)
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
hsToDchTrigger(servHsChangeInterRnc)
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 151 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
hsToDchTrigger(poorQualityDetected)
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
downswitchThreshold
0 to 32
0
0
RNC
Fixed
1kbit/s
downswitchTimer
0 to 1000
10
100
RNC
Fixed
100ms
downswitchTimerThreshold
0 to 64
0
0
RNC
Fixed
1kbit/s
hsdschInactivityTimer
1 to 255
2
10
RNC
Fixed
seconds
ulRlcBufUpswitch
Various
256
256
RNC
Fixed
bytes
dlRlcBufUpswitch
0 to 2000
500
500
RNC
Fixed
bytes
inactivityTimer
1 to 1440
120
10
RNC
Fixed
seconds
inactivityTimerPch
1 to 240
30
30
RNC
Fixed
minutes
dlDownswitchBandwidthMargin
0 to 100
0
80
RNC
Fixed
%
Channel Switching
dlThroughputDownswitchTimer
0 to 2000
20
20
RNC
Fixed
100ms
ulDownswitchBandwidthMargin
0 to 100
0
80
RNC
Fixed
%
ulThroughputDownswitchTimer
0 to 2000
20
20
RNC
Fixed
100ms
bandwidthMargin
0 to 100
90
90
RNC
Fixed
%
upswitchTimer
0 to 100
5
5
RNC
Fixed
100ms
dlThroughputAllowUpswitchThreshold
0 to 100
0
0
RNC
Fixed
%
downswitchPwrMargin
0 to 20
2
2
RNC
Fixed
0.5dB
coverageTimer
0 to 100
10
10
RNC
Fixed
100ms
upswitchPwrMargin
0 to 20
6
6
RNC
Fixed
0.5dB
bandwidthMarginUl
0 to 100
0
90
RNC
Fixed
%
upswitchTimerUl
0 to 100
5
1
RNC
Fixed
100ms
ulThroughputAllowUpswitchThreshold
0 to 100
0
90
RNC
Fixed
%
reportHysteresis
0 to 20
6
6
RNC
Fixed
0.5dB
downswitchTimerSp
0 to 180
2
2
RNC
Fixed
0.5seconds
ulRlcBufUpswitchMrab
Various
8
8
RNC
Fixed
bytes
dlRlcBufUpswitchMrab
0 to 20
0
8
RNC
Fixed
100bytes
inactivityTimeMultiPsInteractive
0 to 10000
50
50
RNC
Fixed
100ms
queueSelectAlgorithm
1 to 6
0=ACKNOLEDGED or
1=TRANSMITTED
1
3
Cell
Fixed
Integer
1=TRANSMITTED
1=TRANSMITTED
Cell
Fixed
Integer
eulTargetRate
0 to 6016
128
128
Cell
Fixed
1kbit/s
eulNoReschUsers
0 to 32
5
5
Cell
Fixed
E-DCH users
eulMaxNoSchEdch
0 to 100
100
16
Cell
Fixed
E-DCH users
airRateTypeSelector
HSDPA Scheduling
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 152 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
eulNoErgchGroups
1. to 4
4
4
Cell
Fixed
E-RGCH groups
eulMaxShoRate
0 to 1472
128
1472
Cell
Fixed
1kbit/s
eulReservedHwBandwidthSchedDataNonServCell
1 to 1472
128
128
Cell
Fixed
1kbit/s
eulThermalLevelPrior
-1150 to -600
-1040
-1040
Cell
Fixed
0.1dBm
eulSlidingWindowTime
10 to 864000
1800
1800
Cell
Fixed
seconds
eulMinMarginCoverage
0 to 1.0
10
10
Cell
Fixed
-
eulNoiseFloorLock
0=FALSE, 1=TRUE
0=FALSE
0=FALSE
Cell
Fixed
-
eulOptimalNoisefloorEstimate
-1150 to -600 or -1
-1040
-1040
Cell
Fixed
0.1dBm
eulMaxRotCoverage
0 to 550
100
100
Cell
Fixed
0.1dB
eulMaxOwnUuLoad
0 to 550
30
80
Cell
Fixed
0.1dB
harqTransmUlTti10Max
1 to 8
4
4
Cell
Fixed
attempts
pwrOffset
0 to 100
5
5
Cell
Fixed
%
pwrHyst
0 to 60000
300
300
Cell
Fixed
ms
iFCong
0 to 621
621
621
Cell
Fixed
0.1dBm
iFOffset
0 to 621
0
0
Cell
Fixed
0.1dB
iFHyst
0 to 6000
6000
6000
Cell
Fixed
10ms
releaseAseDlNg
0 to 500
3
3
Cell
Fixed
ASE
tmInitialGhs
10 to 100000
500
500
Cell
Fixed
ms
tmInitialG
10 to 100000
3000
3000
Cell
Fixed
ms
tmCongActionNg
500 to 100000
800
800
Cell
Fixed
ms
releaseAseDlGhs
0 to 5000
0
0
Cell
Fixed
0.ASE
tmCongActionGhs
10 to 100000
300
300
Cell
Fixed
ms
releaseAseDl
0 to 500
1
1
Cell
Fixed
ASE
tmCongAction
300 to 100000
2000
2000
Cell
Fixed
ms
cchWaitCuT
0 to 200
9
9
RNC
Fixed
5minutes
t305
0 to 7
3=30
3=30
RNC
Fixed
minutes
nOutSyncInd
1 to 256
10
10
Cell
Fixed
frames
rlFailureT
0 to 255
10
10
Cell
Fixed
0.1seconds
nInSyncInd
1 to 256
3
3
Cell
Fixed
frames
dchRcLostT
0 to 100
50
50
RNC
Fixed
0.1seconds
hsDschRcLostT
0 to 600
100
100
RNC
Fixed
0.1seconds
Congestion Detection and Resolution
Radio Connection Supervision
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 153 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
maxFach1Power
-350 to 150
18
18
Cell
Fixed
0.1dB
maxFach2Power
-350 to 150
15
15
Cell
Fixed
0.1dB
pOffset1Fach
0 to 24
0
0
Cell
Fixed
0.1dB
pOffset3Fach
0 to 24
0
0
Cell
Fixed
0.1dB
pO1
0 to 24
0
0
RNC
Fixed
0.25dB
pO3
0 to 24
12
12
RNC
Fixed
0.25dB
minPwrRl
-350 to 150
-150
-150
Cell
Fixed
0.1dB
minimumRate
0 to 1600000
1590
1590
Cell
Fixed
10bps
minPwrMax
-350 to 150
0
0
Cell
Fixed
0.1dB
interRate
0 to 1600000
7760
7760
Cell
Fixed
10bps
interPwrMax
-350 to 150
38
38
Cell
Fixed
0.1dB
maxRate
0 to 1600000
40690
40690
Cell
Fixed
10bps
Power and Code Control
maxPwrMax
-350 to 150
48
48
Cell
Fixed
0.1dB
initShoPowerParam
-20 to 20
-2
-2
RNC
Fixed
1dB
cNbifho
-50 to 150
10
10
RNC
Fixed
0.1dB
dlPcMethod
1 to 4
3=BALANCING
3=BALANCING
RNC
Fixed
Integer
fixedPowerDl
1 to 101
65
65
RNC
Fixed
0.5dB
fixedRefPower
1 to 101
65
65
RNC
Fixed
0.5dB
numHsScchCodes
1 to 4
1
3
Cell
Fixed
codes
flexibleSchedulerOn
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
hsScchMaxCodePower
-35 to 15
-20
-20
Cell
Fixed
0.5dB
hsScchMinCodePower
-35 to 15
-150
-150
Cell
Fixed
0.5dB
qualityCheckPower
-2to 6
0
0
Cell
Fixed
0.5dB
hsPowerMargin
0 to 200
2
2
Cell
Fixed
0.5dB
numHsPdschCodes
1 to 15
5
4
Cell
Fixed
codes
dynamicHsPdschCodeAdditionOn
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
maxNumHsPdschCodes
5 to 15
5
10
Cell
Fixed
codes
ulOuterLoopRegulator
0 or 1
1=JUMP
1=JUMP
RNC
Fixed
Integer
ulSirStep
0 to 50
10
10
RNC
Fixed
0.1dB
blerQualityTargetDl(1,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(2,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 154 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
blerQualityTargetDl(2,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(2,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(2,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(5,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(5,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(6,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(6,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(18,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(18,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(7,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(7,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(9,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(9,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(9,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(9,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(9,5)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(10,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(10,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(10,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(10,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(10,5)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(11,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(12,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(12,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(12,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(12,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(15,1)
-63 to 0
-30
-30
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(15,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(16,1)
-63 to 0
-30
-30
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(16,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(19,1)
-63 to 0
-30
-30
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(19,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 155 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
blerQualityTargetDl(19,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(19,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(19,5)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(20,1)
-63 to 0
-30
-30
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(20,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(20,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(20,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetDl(20,5)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(1,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(2,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(2,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(2,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(2,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(5,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(5,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(6,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(6,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(18,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(18,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(7,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(7,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(9,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(9,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(9,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(9,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(9,5)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(10,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(10,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(10,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(10,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(10,5)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(11,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(12,1)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(12,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 156 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
Ericsson Default
AT&T Recommended
Level
Class
Unit
blerQualityTargetUl(12,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(12,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(15,1)
-63 to 0
-30
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(15,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(16,1)
-63 to 0
-30
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(16,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(19,1)
-63 to 0
-30
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(19,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(19,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(19,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(19,5)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(20,1)
-63 to 0
-30
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(20,2)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(20,3)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(20,4)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
blerQualityTargetUl(20,5)
-63 to 0
-20
-20
RNC
Fixed
10 Log10(BLER)
sirMax
-82 to 173
100
120
RNC
Fixed
0.1dB
sirMin
-82 to 173
-82
-82
RNC
Fixed
0.1dB
deltaAck1
0 to 8
4
5
Cell
Fixed
-
deltaAck2
0 to 8
8
7
Cell
Fixed
-
deltaNack1
0 to 8
4
5
Cell
Fixed
-
deltaNack2
0 to 8
8
7
Cell
Fixed
-
deltaCqi1
0 to 8
4
4
Cell
Fixed
-
deltaCqi2
0 to 8
8
6
Cell
Fixed
-
initialCqiRepetitionFactor
1 to 4
1
1
Cell
Fixed
-
initialAcknackRepetitionFactor
1 to 4
1
1
Cell
Fixed
-
hsMeasurementPowerOffset
-30 to 160
80
80
Cell
Fixed
0.1dB
codeThresholdPdu656
0 to 15
6
6
Cell
Fixed
codes
cqiFeedbackCycle
0 to 160
8
8
Cell
Fixed
ms
cqiErrors
0 to 100
10
10
Cell
Fixed
-
cqiErrorsAbsent
0 to 100
10
10
Cell
Fixed
-
cqiAdjustmentOn
0=FALSE, 1=TRUE
0=FALSE
1=TRUE
RNC
Fixed
Binary
hardIfhoCorr
-5 to +15
3
3
Cell
Fixed
dB
maxUserEhichErgchPowerDl
-35 to 15
3
3
RNC
Fixed
dB
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 157 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Parameter
Range
maxEagchPowerDl
-35 to 15
3
3
RNC
Fixed
dB
transmissionTargetError
1 to 50
3
3
RNC
Fixed
%
ulInitSirTargetEdch
-82 to 173
3
3
RNC
Fixed
0.1dB
ND-00150
Rev. 3.0 09/09/2007
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Ericsson Default
AT&T Recommended
Page 158 of 170
© 2007 AT&T
Level
Class
Unit
Volume II – Ericsson Field Guide for UTRAN P3
10. Consulted List
The following individuals have participated in the creation of this document through their participation in
the National Ericsson UTRAN (NEU) Forum. The name of each participant is provided along with the
group (region in parentheses) each participant represents.
Area
Austin (C)
Chicago (C)
Dallas (C)
Houston (C)
Boston (NE)
San Diego (W)
ND-00150
Rev. 3.0 09/09/2007
Name in Exchange GAL
Lewis, Robert S
Quinonez, Rick
Bendele, Shelia
Barrientos, Joseph
Richard, Hill
Wheat, Mike
Hernandez, Hugo
Munoz, Domingo
Birch, Elizabeth (Lavallee)
Bledsoe, Ronald W
Olsen, Scott
Berner, William
Burt, Shannon M
Ciszkowski, Jaroslaw
Compton, James
Kanya Jr, Walter
Mahalik Jr, Daniel H
Melchior, Christopher
Morrisey, Bernadette
Sayeed, Adil
Stearns, Todd D
Vega, Jorge (Eng-Chi)
Pasillas, Juan
Scharosch, Greg
Parkoff, Seth
Wang, Jimmy
Coleman, Phillip
Shelton, David
Chan, Rosa
Wells, Bobby
Steward, H. Jim
Smith, J. Mike (NTX)
Jackowski, Frank
Wheat, Mike
Centeno, Edgardo
Suarez-rivero, Alberto
Gibson, Adrienne
Wysocki, Tim
Lowery, Rich
Leary, Jeff
Negi, Lokeshi (LCC)
Robinson, John (BOSTON)
Melanson, Steve
Dunakin, Jeffrey
Vieira, Mark
Mariano, Jobet
Sebastian, Arvin
Heath, Tony
Doiron, Mike
Pinto, Victor
Williamson, Andrew
Bianco, Paul
Bossom, Michael
Noet, Mark
Olah, Otto
Salas, Tony
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 159 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Area
San Francisco / San Jose (W)
Atlanta (SE)
Indianapolis (C)
Gary (C)
San Antonio (C)
Oklahoma City (C)
Raleigh
Citrus / Tampa / Lakeland (SE)
Daytona / Orlando / Cape Canavera / Boca Raton (SE) aka S. FL
Boca Raton (SE) (S. FL)
Gainesville / Tallahassee / Jacksonville (SE) aka N. FL
ND-00150
Rev. 3.0 09/09/2007
Name in Exchange GAL
Taylor, Chris K
Banchongsirichareon, Soontorn
Chan, Christopher
Patel, Chetan
Caniglia, Michael
Albrecht, Frank
Parra, Darwin
Arefin, S
Suh, Young
Abdul, Majdi
Murdock, Monty
Pitzini, Marcel
Neuman, Rick
Lavender, Tyann
Corbett, Jason
Henderson, Tom
Won Jr, Toussant
Jabbary, Ali
Perry, Ben
Sieber, John
Bledsoe, Ronald W
Salyer, David
Tadlock, Jimmie
Bongiorno, Matt
Cisneros, Ivan
LaLonde, Michael
Pilgrim, Pam
Smedley, Dale
Benson, Brent
Bickle, Jerry
Brunnert, David
LaCava, Dave
Jacob, Taylor
Orsak, Joseph
Althaf, Mohammed
Birkey, Jeff
McKenney, Scott
Self, Roger
Hussain, Umer
Combs, Tom
Raymundo, Fellou
Ziers, Kirk
Li, Sandy
Hoshyar, Zana
Ramos, Wilson
Chiodo, Russ
Gomez, Marcel
Vencl, Lu
Pinto, Avelino
Chang, Marty
Mills, Peter
Flores, Laura V FL
Douglas, Handel
Graham, Joseph
Guidry, Aaron
Fanning, Thomas
Dinges, Chris
Habib, Jamal
Joyce, Sharon
Araujo, Noemi
Bravo, Felix
Ward, Joseph
Reilly, Joe
Austin, Ken
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 160 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Area
Charlotte (SE)
Vallejo (W)
Fresno, Sacramento, Stockton (W)
Little Rock (C)
Tulsa (C)
Miami / West Palm Beach (SE)
Milwaukee (C)
Birmingham (SE)
Knoxville, TN (SE)
Pittsburgh (C)
Bridgeport / Hartford / New Haven, CT (NE)
Providence (NE)
San Juan (SE)
Baton Rouge / New Orleans (SE)
Louisville / Memphis / Nashville (SE)
ND-00150
Rev. 3.0 09/09/2007
Name in Exchange GAL
Keys, Kraig
Bush, Patricia
Sewell, David
Kunakorn, Jay
Dennis, Michael
Brown, Steven C
Albrecht, Frank
Albrecht, Frank
Appert, Douglas
Riar, Paul
Mirano, Edmund
Patel, Neville
Pack, Mark
Howell, Bill
Pittman, Donald
DiMaso, Filippo
Kommer, James
Bowling, Garry
Thomas, Randy
Warr, Amanda
Workman, Owen
George, Monty
Cookson, Ken
Webb, David
Albright, Anthony
Warwick, Robert
Hood, Edwan
Harris, James M.
Lee, Bryon
Mitchell, Terri A
Helle, Erika
Helle, Steve
Cook, John Z
Thomas, Matthew
Dugan, Shawn
Klein, Robert S.
Saddig Jr., Walter C.
Crawford, Ken
Negi, Lokeshi (LCC)
Biernat, S. Irek
Ownbey, Jason
Ezquerra, Guillermo
Smith, Todd R
Velez, Wilfredo
Ortiz, Leslie L.
Casillas, Roberto
Diaz, William
Turlington, David
Deets, Bernie
George, Monty
Jones, Robert
Stephens, Mike
Andre, Tracy
Salvo, Mike
Kiefer, Ron
Green, Tracey
Matthews, Brian
McNear, Jerome
Torrence, Tina
Corbett, Brian
Horn, Byron
Schutts, Will
Lewis, Mike
Dunn, Jerry
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 161 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Area
Evansville (SE)
Clarksville (SE)
Chattanooga (SE)
Greensboro (SE)
Columbia (SE)
Los Angeles / Bakersfield / Oxnard (W)
ND-00150
Rev. 3.0 09/09/2007
Name in Exchange GAL
Plantz, William
Bale, Jeff
Sigmon, Edward
Batson, Wynn
Taylor, Lyle
Gillian, Tara
Bennett, Danny
Horton, Jarrod
Antonaccio, Lenny
Nance, John
Eskew, Steve
Campbell, Tim
Rohdy, John
Krug, Donald
Reeves, Larry
Williams, John S
Fontela, Gonzalo
Kerchief, Brian
Wahnsiedler, John
Knepler, Andrew
Wilbanks, Richard
Duncan, Trudy
Martin, Brent
Hedges, David
Bodford, Paul
Shahoud, Joe
Alfakir, Sam
Hollister, Jim
Wan, Wang
Hussain, Zahid
Singh, Bhupender
Nguyen, Tom
Jin, Min
Polard, Essie
Banuelos, Monica
Noet, Mark
Heeney-Fouts, Kathleen
Monroe, Richard
Diaz, Jimmy
Wan, Wang
Noonan, Robert
Hernandez, Carlos C
Abdullah, Haris
Moreno, Orlando
Nguyen, Tuong
Masada, Gary
Santos, Christian
Rubin, Robert
Melton, Sean
Qazi, Adil
Barnett, Marlion
Papadopoulos, Dimitris
Usmani, Ehtesham
Chow, Gary
Kilic, Semsettin
Ahad, Adil
Hilario, Marissa
Taylor, Chris K
Cram, Steve
Sharma, Amitabh
Shimizu, Nelson
Fayaz, Mohammad
Lopez, Trin
Hurst, Fred
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 162 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Area
New Bedford, CT (NE)
McAllen (C)
Honolulu (W)
El Paso (C)
Newport News, Norfolk (NE)
Richmond (NE)
Mobile (SE)
Greenville (SE)
Charleston / Cabarrus (SE)
Virginia / West Virginia (SE)
Western Region
Central Region
Northeast Region
ND-00150
Rev. 3.0 09/09/2007
Name in Exchange GAL
Jones, Harold M
Mohammed, Aleemuddin
Siddiqui, Zafar
Emina, Henry
Fahs, Najib
Madregallejo, Daniel
Petelo, Paul
Islam, Md
Khan, Salman
Ghazali, Noman
Assan, Emmanuel
Osztermann, Gabriel
Dixon, Edward
Slowinski, Marek
Olah, Otto
Qureshi, Jamal
Celik, Yilmaz
Yoeu, Abdul Z
Klein, Robert S.
Tadlock, Jimmie
Oshiro, Henry
Rocha, S. Adrian
Mughal, Naeem
Khalaf, Emile (Tony)
Mughal, Naeem
Patel, Vipul
Tolbert, Michael
Hill, Tommy
Draper, Trent
Petree, Howard
Tyson, Roger
Abedin, Tariq
Costanzo, Ross
Young, James
Caine, Richard
Ulanday, Daniel
Clark, Robert I.
Solis, Bobie
Eter, Elias
Azam, Shehzad (OSS)
Delany, Clive
Venkatesalu, Ramkumar
Akkaya, Sinan
Puttabuddi, Kiran (OSS)
Hawkes, Peter
Shen, Chun
Palmer, Craig
Aguon, Paul (OSS)
Thompson, Nicholas R
Baltazar, Alona
Ye, Weihua
Gupta, Sandeep
Ion, Florian
Ryan, William P
Cai, Nancy
Garcia, Oscar
Zahan, Eusebiu
Robinson, William
Apollonio, Laura
May, Christopher (OSS)
Khuu, Khoa
Davis, Richard J
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 163 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Area
South
Strategic Planning (CTO)
National Field Support
National Quality and Performance (national scorecard)
National Services Operations
Network Support
Subscriber Product Engineering
National RF Engineering
ND-00150
Rev. 3.0 09/09/2007
Name in Exchange GAL
Elliott, John J. (OSS)
Rai, Paritosh
Gray, Randal (Randy)
McCarthy, Brian
Chopra, Namita
Hetrick, Kevin
Langley, Brett
Fix, Jeremy
Salmon, Michael
Grabau, Mike
Ballard, Troy
Powell, Lamont
Ask Lamont (OSS)
Murray, Arthur
Ramos, Wilson
Tayyebi, Sean
Robertson, Stuart
Vallath, Sree
Sam, Anthony
Choi-Grogan, Shirley
Orloff, David
Portzer, Bruce
Unny, Pradeep
Gopalan, Rajasekhar (Raja)
Huber, Kurt D.
Bigler, Laurie A
Bakhtiari, Farideh (OSS)
Clendenen, Dave (OSS)
Kelly, Thomas HQ (OSS)
Brisebois, Art
Heubel, Michael
Tong, Hendry
Smith, Juan (Derrick)
Carrillo, Joe
Scheihing, Terry
Davis, Charles
Mascarenhas, Patrick
Thompson, Edmund (Eddie)
Patini, Joe
Hristov, Hristo
Razdan, Somesh
Barnes, Karen
Jaidi, Khalil
Kim, Agnes
Holmberg, Erik
Elf, Mats
Wiese, Bill
Hurst, Fred
Heeney-Fouts, Kathleen
Kim, Yon
Villapando, Vladimir
Schiefelbein, Lee
Broderick, John
Ellis, Steve
Schiefelbein, Lee
Phillips, Larry
Bell, Wayne
Jann, Petr
James, Dan
Lee, Bo
Salazar, Gil
Delmendo, Eddie
Hlavaty-Laposa, Michael
Herndon, Al
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 164 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
Area
National PMO
Subscriber Services
Ericsson
Award Solutions
Qualcomm
National OSS Group
ND-00150
Rev. 3.0 09/09/2007
Name in Exchange GAL
Narang, Ashish
Swanson, Kurt R
Kapoulas, Spyridon
Gohel, Kaushik
Connell, Donna
Pratt, Jim
Abad, Younes (UTRAN)
Inge, Johnsson (OSS)
Dirocco, Andrea (UTRAN)
Mao, Tom (UTRAN)
Zabka, Craig (West Region)
Statnikov, Mark (Central Region)
Wallen, Mats (SouthEast Region)
Magnus, Hedenlund (NorthEast Region)
Celedon, Rafael
Mir, Nabeel
Hatipoglu, Can
Jianli Wang J (PL/EUS)
Collins, Kerwin
Tripathi, Manish
Dodge, Chris (OSS)
Glunt, Robb (OSS)
Padowski, Dan (OSS)
Riley, Tyrus (OSS)
Shows, Darren (OSS)
Zurbriggen, Mark (OSS)
May, Christopher (OSS)
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 165 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
11. Index
A
accessClassNbarred ................................27, 147
activeQueueMgmt ....................................51, 149
aichPower...........................................25, 29, 147
airRateTypeSelector ................................86, 152
allow384HsRab ............................36, 42, 50, 147
aseDlAdm.................................................46, 148
aseUlAdm.................................................45, 148
aseUlAdmOffset .......................................45, 148
att ...................................................9, 24, 28, 147
B
bandwidthMargin......................................80, 152
bandwidthMarginUl ..................................82, 152
bchPower .................................................23, 146
beMarginAseDl.........................................46, 148
beMarginAseUl.........................................45, 148
beMarginDlCode ......................................41, 148
beMarginDlHw..........................................48, 148
beMarginDlPwr.........................................43, 148
beMarginUlHw..........................................47, 148
blerQualityTargetDl(1,1).................................154
blerQualityTargetDl(10,1)...............................155
blerQualityTargetDl(10,2)...............................155
blerQualityTargetDl(10,3)...............................155
blerQualityTargetDl(10,4)...............................155
blerQualityTargetDl(10,5)...............................155
blerQualityTargetDl(11,1)...............................155
blerQualityTargetDl(12,1)...............................155
blerQualityTargetDl(12,2)...............................155
blerQualityTargetDl(12,3)...............................155
blerQualityTargetDl(12,4)...............................155
blerQualityTargetDl(15,1)...............................155
blerQualityTargetDl(15,2)...............................155
blerQualityTargetDl(16,1)...............................155
blerQualityTargetDl(16,2)...............................155
blerQualityTargetDl(18,1)...............................155
blerQualityTargetDl(18,2)...............................155
blerQualityTargetDl(19,1)...............................155
blerQualityTargetDl(19,2)...............................155
blerQualityTargetDl(19,3)...............................156
blerQualityTargetDl(19,4)...............................156
blerQualityTargetDl(19,5)...............................156
blerQualityTargetDl(2,1).................................154
blerQualityTargetDl(2,2).................................155
blerQualityTargetDl(2,3).................................155
blerQualityTargetDl(2,4).................................155
blerQualityTargetDl(20,1)...............................156
blerQualityTargetDl(20,2)...............................156
blerQualityTargetDl(20,3)...............................156
ND-00150
Rev. 3.0 09/09/2007
blerQualityTargetDl(20,4) .............................. 156
blerQualityTargetDl(20,5) .............................. 156
blerQualityTargetDl(5,1) ................................ 155
blerQualityTargetDl(5,2) ................................ 155
blerQualityTargetDl(6,1) ................................ 155
blerQualityTargetDl(6,2) ................................ 155
blerQualityTargetDl(7,1) ................................ 155
blerQualityTargetDl(7,2) ................................ 155
blerQualityTargetDl(9,1) ................................ 155
blerQualityTargetDl(9,2) ................................ 155
blerQualityTargetDl(9,3) ................................ 155
blerQualityTargetDl(9,4) ................................ 155
blerQualityTargetDl(9,5) ................................ 155
blerQualityTargetUl(1,1) ................................ 156
blerQualityTargetUl(10,1) .............................. 156
blerQualityTargetUl(10,2) .............................. 156
blerQualityTargetUl(10,3) .............................. 156
blerQualityTargetUl(10,4) .............................. 156
blerQualityTargetUl(10,5) .............................. 156
blerQualityTargetUl(11,1) .............................. 156
blerQualityTargetUl(12,1) .............................. 156
blerQualityTargetUl(12,2) .............................. 156
blerQualityTargetUl(12,3) .............................. 157
blerQualityTargetUl(12,4) .............................. 157
blerQualityTargetUl(15,1) .............................. 157
blerQualityTargetUl(15,2) .............................. 157
blerQualityTargetUl(16,1) .............................. 157
blerQualityTargetUl(16,2) .............................. 157
blerQualityTargetUl(18,1) .............................. 156
blerQualityTargetUl(18,2) .............................. 156
blerQualityTargetUl(19,1) .............................. 157
blerQualityTargetUl(19,2) .............................. 157
blerQualityTargetUl(19,3) .............................. 157
blerQualityTargetUl(19,4) .............................. 157
blerQualityTargetUl(19,5) .............................. 157
blerQualityTargetUl(2,1) ................................ 156
blerQualityTargetUl(2,2) ................................ 156
blerQualityTargetUl(2,3) ................................ 156
blerQualityTargetUl(2,4) ................................ 156
blerQualityTargetUl(20,1) .............................. 157
blerQualityTargetUl(20,2) .............................. 157
blerQualityTargetUl(20,3) .............................. 157
blerQualityTargetUl(20,4) .............................. 157
blerQualityTargetUl(20,5) .............................. 157
blerQualityTargetUl(5,1) ................................ 156
blerQualityTargetUl(5,2) ................................ 156
blerQualityTargetUl(6,1) ................................ 156
blerQualityTargetUl(6,2) ................................ 156
blerQualityTargetUl(7,1) ................................ 156
blerQualityTargetUl(7,2) ................................ 156
blerQualityTargetUl(9,1) ................................ 156
blerQualityTargetUl(9,2) ................................ 156
blerQualityTargetUl(9,3) ................................ 156
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 166 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
blerQualityTargetUl(9,4).................................156
blerQualityTargetUl(9,5).................................156
C
cBackOff...................................................31, 147
cchWaitCuT..............................................91, 153
cellReserved ......................................25, 27, 147
cNbifho .....................................................93, 154
cnDrxCycleLengthCs .........................25, 38, 148
cnDrxCycleLengthPs..........................25, 38, 148
codeThresholdPdu656 ...................................157
compModeAdm ........................................39, 148
ConstantValueCprach ........................25, 29, 147
coverageTimer .........................................83, 152
cPO ....................................................32, 33, 147
cqiAdjustmentOn ............................................157
cqiErrors .........................................................157
cqiErrorsAbsent..............................................157
cqiFeedbackCycle..........................................157
D
dchRcLostT ..............................................91, 153
defaultHoType ................................2, 11, 63, 151
deltaAck1........................................................157
deltaAck2........................................................157
deltaCqi1 ........................................................157
deltaCqi2 ........................................................157
deltaNack1 .....................................................157
deltaNack2 .....................................................157
directedRetryTarget .................................50, 149
dlCodeAdm ..............................................41, 148
dlDownswitchBandwidthMargin ...............78, 152
dlHwAdm ..................................................48, 148
dlInitSirTarget ...............................31, 92, 93, 147
dlPcMethod ..............................................93, 154
dlRlcBufUpswitch .....................................75, 152
dlRlcBufUpswitchMrab .............................85, 152
dlThroughputAllowUpswitchThreshold.....80, 152
dlThroughputDownswitchTimer ...............78, 152
downswitchPwrMargin .......................80, 83, 152
downswitchThreshold.........................71, 73, 152
downswitchTimer ...............................71, 73, 152
downswitchTimerSp .................................84, 152
downswitchTimerThreshold .....................73, 152
dynamicHsPdschCodeAdditionOn ...........94, 154
E
ecNoPcpichDefault.............................31, 93,
emergencyCallRedirect............................49,
eulMaxNoSchEdch...................................87,
eulMaxOwnUuLoad..................................88,
eulMaxRotCoverage ................................87,
ND-00150
Rev. 3.0 09/09/2007
147
149
152
153
153
eulMaxShoRate ....................................... 87, 153
eulMinMarginCoverage............................ 87, 153
eulNoErgchGroups .................................. 87, 153
eulNoiseFloorLock ................................... 87, 153
eulNonServingCellUsersAdm .................. 39, 148
eulNoReschUsers .................................... 87, 152
eulOptimalNoisefloorEstimate ....................... 153
eulReservedHwBandwidthSchedDataNonServC
ell ................................................................ 153
eulServingCellUsersAdm......................... 39, 148
eulSlidingWindowTime ............................ 87, 153
eulTargetRate .......................................... 87, 152
eulThermalLevelPrior............................... 87, 153
F
fachMeasOccaCycLenCoeff .................... 52,
FddGsmHoSupp ...................................... 63,
FddIfHoSupp............................................ 63,
filterCoeff4_2b.......................................... 69,
filterCoeff6................................................ 62,
filterCoefficient1 ....................................... 57,
filterCoefficient2 ....................................... 62,
fixedPowerDl............................................ 93,
fixedRefPower.......................................... 94,
flexibleSchedulerOn................................. 94,
149
151
151
151
150
150
150
154
154
154
G
gsmFilterCoefficient3 ............................... 66, 151
gsmThresh3a ...............................64, 65, 66, 151
H
hardIfhoCorr................................................... 157
harqTransmUlTti10Max ........................... 88, 153
hoType ..................................................... 63, 151
hsCellChangeAllowed.............................. 70, 151
hsdpaUsersAdm ...................................... 39, 148
hsdschInactivityTimer .............................. 74, 152
hsDschRcLostT........................................ 91, 153
hsHysteresis1d ........................................ 70, 151
hsMeasurementPowerOffset ......................... 157
hsOnlyBestCell ........................................ 50, 149
hsPowerMargin ........................................ 94, 154
hsQualityEstimate .................................... 70, 151
hsScchMaxCodePower ........................... 94, 154
hsScchMinCodePower ............................ 94, 154
hsTimeToTrigger1d.................................. 70, 151
hsToDchTrigger(changeOfBestCellIntraRnc). 70,
151
hsToDchTrigger(poorQualityDetected)..... 58, 71,
152
hsToDchTrigger(servHsChangeInterRnc)70, 151
hsToDchTrigger(servHsChangeIntraRnc)70, 151
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 167 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
hyst4_2b.......................................67, 68, 69,
hysteresis1a .......................................26, 54,
hysteresis1b .......................................26, 55,
hysteresis1c .......................................26, 56,
hysteresis1d .......................................26, 57,
hysteresis2d .......................................58, 59,
hysteresis2f ..............................................60,
hysteresis3a .................................64, 65, 66,
151
149
150
150
150
150
150
151
I
iFCong......................................................90, 153
iFHyst .......................................................90, 153
iFOffset.....................................................90, 153
inactivityTimeMultiPsInteractive ...............86, 152
inactivityTimer ..........................................76, 152
inactivityTimerPch ....................................77, 152
individualOffset(UtranCell) .... 57, 63, 66, 69, 150
initialAcknackRepetitionFactor .......................157
initialCqiRepetitionFactor ...............................157
initShoPowerParam .................................93, 154
interFreqFddMeasIndicator ......................52, 149
interPwrMax .............................................92, 154
interRate...................................................92, 154
L
lAC......................................................24, 34,
loadSharingCandidate..............................50,
loadSharingDirRetryEnabled ...................50,
loadSharingGsmFraction .........................50,
loadSharingGsmThreshold ......................50,
loadSharingMargin ...................................50,
loadSharingRrcEnabled ...........................50,
147
149
149
149
149
149
149
M
maxActiveSet .....................................54, 56, 149
maxEagchPowerDl...................................97, 158
maxFach1Power ......................................91, 154
maxFach2Power ......................................91, 154
maximumTransmissionPower 11, 43, 80, 83, 88,
94, 148
maxNumHsdpaUsers ...............................39, 148
maxNumHsPdschCodes ..........................94, 154
maxPreambleCycle ..................................29, 147
maxPwrMax .............................................92, 154
maxRate ...................................................92, 154
maxTxPowerUl ...................................25, 28, 147
maxUserEhichErgchPowerDl...................97, 157
mcc...........................................................24, 146
measQuantity1 ...................................55, 56, 150
minimumRate ...........................................92, 154
minPwrMax...............................................92, 154
minPwrRl ..................................................92, 154
ND-00150
Rev. 3.0 09/09/2007
mnc .......................................................... 24, 146
multiRabSp0Available.............................. 36, 147
multiRabUdi8Available............................. 36, 147
N
nInSyncInd ............................................... 91, 153
nmo .......................................................... 25, 147
nonUsedFreqThresh4_2bEcno.......... 67, 68, 151
nonUsedFreqThresh4_2bRscp....67, 68, 69, 151
nonUsedFreqW4_2b................................ 69, 151
noOfMaxDrxCycles .................................. 38, 148
noOfMibValueTagRetrans ....................... 23, 146
noOfPagingRecordTransm ...................... 38, 148
nOutSyncInd ............................................ 91, 153
numHsPdschCodes ................................. 94, 154
numHsScchCodes ................................... 94, 154
P
packetEstMode ........................................ 51, 149
pchPower ................................................. 38, 148
pcpichPowerDefault ................................. 33, 147
pichPower .......................................... 25, 37, 147
pO1 ..............................................31, 32, 92, 154
pO2 .................................................... 31, 32, 147
pO3 ..............................................31, 32, 92, 154
pOffset1Fach ........................................... 92, 154
pOffset3Fach ........................................... 92, 154
powerOffsetP0 ................................... 26, 29, 147
powerOffsetPpm ...................................... 30, 147
preambleRetransMax ........................ 26, 29, 147
primaryCpichPower.....19, 25, 29, 31, 32, 33, 92,
93, 97, 146
primarySchPower..................................... 22, 146
primaryScramblingCode ..............18, 19, 23, 146
psStreaming128....................................... 36, 147
pwrAdm........................................43, 50, 88, 148
pwrAdmOffset .................................... 43, 88, 148
pwrHyst .................................................... 88, 153
pwrOffset.................................................. 88, 153
Q
qHyst1...................................................... 53, 149
qHyst2................................................ 25, 53, 149
qOffset1sn(GsmRelation) .................... 9, 53, 149
qOffset1sn(UtranRelation) ................... 9, 53, 149
qOffset2sn................................................ 53, 149
qQualMin......................................25, 28, 52, 147
qRxLevMin .............................25, 27, 28, 52, 147
qualityCheckPower .................................. 94, 154
qualMeasQuantity .............................. 25, 53, 149
queueSelectAlgorithm.............................. 86, 152
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 168 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
R
rAC .....................................................25, 34,
releaseAseDl ............................................91,
releaseAseDlGhs .....................................90,
releaseAseDlNg .......................................90,
releaseConnOffset .............................54, 56,
reportHysteresis .......................................83,
reportingInterval1a ...................................54,
reportingInterval1c ...................................56,
reportingRange1a ..............................26, 54,
reportingRange1b ..............................26, 55,
rlFailureT ..................................................91,
147
153
153
153
149
152
150
150
149
150
153
S
secondarySchPower ................................23, 146
sf16Adm ...................................................42, 148
sf16AdmUl................................................42, 148
sf16gAdm .................................................42, 148
sf32Adm ...................................................42, 148
sf4AdmUl..................................................42, 148
sf4UlPathlossThreshold ...........................50, 149
sf8Adm .....................................................42, 148
sf8AdmUl..................................................42, 148
sHcsRat..............................................25, 52, 149
sib11RepPeriod........................................24, 146
sib11StartPos ...........................................24, 146
sib12RepPeriod........................................24, 147
sib12StartPos ...........................................24, 147
sib1PLMNScopeValueTag .................24, 27, 146
sib1RepPeriod..........................................24, 146
sib1StartPos .............................................24, 146
sib3RepPeriod..........................................24, 146
sib3StartPos .............................................24, 146
sib5RepPeriod..........................................24, 146
sib5StartPos .............................................24, 146
sib7expirationTimeFactor.........................26, 146
sib7RepPeriod....................................24, 26, 146
sib7StartPos .............................................24, 146
sInterSearch .............................................52, 149
sIntraSearch .............................................52, 149
sirMax.............................................................157
sirMin..............................................................157
sRatSearch ........................................25, 52, 149
state128_128Supported...........................37, 147
supportOf16qam ......................................15, 146
T
t305 ..........................................................91, 153
t3212 ..................................................24, 34, 147
timeToTrigger1a.................................26, 54, 149
timeToTrigger1b.................................26, 55, 150
timeToTrigger1c .................................26, 56, 150
ND-00150
Rev. 3.0 09/09/2007
timeToTrigger1d................................. 26, 57, 150
timeToTrigger2dEcno ........................ 58, 59, 150
timeToTrigger2dRscp ........................ 58, 59, 150
timeToTrigger2fEcno ............................... 60, 150
timeToTrigger2fRscp ............................... 60, 151
timeToTrigger3a...........................64, 65, 66, 151
timeToTrigger6d................................. 11, 61, 150
timeTrigg4_2b ..............................67, 68, 69, 151
timeTrigg6b .............................................. 62, 150
tmCongAction .......................................... 91, 153
tmCongActionGhs.................................... 90, 153
tmCongActionNg...................................... 90, 153
tmInitialG............................................ 90, 91, 153
tmInitialGhs .............................................. 90, 153
transmissionTargetError .......................... 97, 158
treSelection ........................................ 25, 53, 149
txPowerConnQualMonEnabled .........61, 62, 150
U
uarfcnDl........................................11, 13, 63, 146
uarfcnUl.................................................... 13, 146
ueTxPowerThresh6b ............................... 62, 150
ulDownswitchBandwidthMargin ............... 79, 152
ulHwAdm.................................................. 47, 148
ulInitSirTargetEdch .................................. 97, 158
ulInitSirTargetExtraHigh........................... 33, 147
ulInitSirTargetHigh ................................... 33, 147
ulInitSirTargetLow .................................... 33, 147
ulInitSirTargetSrb ..................................... 33, 147
ulOuterLoopRegulator ............................. 94, 154
ulPathlossCheckEnabled......................... 50, 149
ulRlcBufUpswitch ..................................... 75, 152
ulRlcBufUpswitchMrab............................. 85, 152
ulSirStep .................................................. 94, 154
ulThroughputAllowUpswitchThreshold .... 82, 152
ulThroughputDownswitchTimer ............... 79, 152
upswitchPwrMargin.................................. 80, 152
upswitchTimer.......................................... 80, 152
upswitchTimerUl ...................................... 82, 152
usedFreqRelThresh2fEcno...................... 60, 150
usedFreqRelThresh2fRscp...................... 60, 150
usedFreqRelThresh4_2bEcno................. 67, 151
UsedFreqRelThresh4_2bRscp ..........68, 69, 151
usedFreqThresh2dEcno(hho).................. 58, 150
usedFreqThresh2dEcno(sho) .................. 59, 150
usedFreqThresh2dEcnoDrnc................... 59, 150
usedFreqThresh2dRscp(hho).............. 9, 58, 150
usedFreqThresh2dRscp(sho) .................. 59, 150
usedFreqThresh2dRscpDrnc................... 59, 150
usedFreqW2d .......................................... 63, 151
usedFreqW2f ........................................... 63, 151
usedFreqW4_2b ...................................... 69, 151
utranDrxCycleLength ............................... 38, 148
utranFilterCoefficient3.................................... 151
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 169 of 170
© 2007 AT&T
Volume II – Ericsson Field Guide for UTRAN P3
utranRelThresh3aEcno ............................64,
utranRelThresh3aRscp ......................65, 66,
utranRelThreshRscp ..........................66, 69,
utranW3a..................................................67,
ND-00150
Rev. 3.0 09/09/2007
151
151
151
151
W
w1a .......................................................... 58, 150
w1b .......................................................... 58, 150
AT&T CONFIDENTIAL & PROPRIETARY
Use pursuant to Company instructions
Page 170 of 170
© 2007 AT&T
Download