Uploaded by Jim maan

Zynq-Systems-Guide-Digital-v6a

advertisement
AVNET BOARDS
Xilinx Solutions Guide
DESIGN IT OR BUY IT?
Avnet’s Ready-made SoC Modules Will Shorten Your Development Cycle
Today’s quick time-to-market demands are forcing you to rethink how you design, build, and deploy your products. Typically, it’s faster, less
costly, and lower risk to incorporate an off-the-shelf solution instead of designing from the beginning. Avnet’s System-On-Module (SOM)
and Single-Board Computer (SBC) solutions for the Xilinx Zynq-7000 SoC, Zynq UltraScale+ MPSoC and Zynq UltraScale+ RFSoC can reduce
development times by more than twelve months, allowing you to focus your efforts on adding differentiating features and unique capabilities.
Avnet’s SoC Modules Offer the Following Benefits:
- Reduce risk by building your application upon a known working system
- Get running quickly with example designs, tutorials, and board support packages
- Start software development immediately
- Eliminate costly board re-spins
- Start with proven Carrier designs
- SOM and carrier customization through Avnet Design Services
With over fifteen years of experience building SOM products, we’ve helped many companies attain a jump start on their products and get
to market faster. Contact us today to get started!
Table of Contents
MiniZed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
UltraZed-EV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
A single-core Zynq 7Z007S entry-level development board with 8 GB
eMMC memory that supports an Arduino shield expansion interface.
Provides USB and a Murata wireless module for Wi-Fi and Bluetooth. Also
LEDs, a pushbutton, switch, motion and temp sensor and a microphone.
The UltraZed-EV is a flexible SOM based on the Xilinx Zynq UltraScale+
MPSoC. The 7EV device includes the Xilinx VCU and is an ideal platform
for embedded video processing. On-board features include dual
system memory, configuration memory, high-speed transceivers,
ethernet, and USB.
MicroZed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MicroZed is a low-cost board based on the Xilinx Zynq-7000 SoC. MicroZed
is unique as both a standalone board for basic SoC experimentation or
combined with a carrier card as a SOM. MicroZed is available in 7010 and
7020 varieties as well as both C- and I-temp grades.
PicoZed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PicoZed is a highly flexible, rugged SOM based on the Xilinx Zynq-7000
SoC. Family members allow migration between the 7010, 7015, 7020, and
7030 Zynq-7000 devices in a pin-compatible footprint. The 7015/7030
also include transceivers. All are offered in Industrial temperature grade.
Ultra96-V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
The Ultra96-V2 is an Arm-based, Xilinx Zynq UltraScale+ MPSoC SingleBoard-Computer based on Linaro 96Boards’ CE spec. On-board certified
WiFi/BT radio, USB 3.0, DisplayPort, SD Card, and 96Boards Mezzanine
expansion support application development like Artificial Intelligence
with Vitis AI.
UltraZed-EG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
The UltraZed-EG SOM is a highly flexible, rugged SOM based on the
Xilinx Zynq UltraScale+ MPSoC. Designed in a smaller form factor (7
sq in), this SOM uses the 3EG device and packages the RAM, Flash,
Ethernet, USB, and configuration memory needed for an embedded
processing system.
XRF RFSoC SOMs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Avnet XRF™ RFSoC System-on-Modules are designed for large-scale
integration into deployed RF systems demanding small footprint, low
power, and real-time processing. XRF modules feature the Xilinx Zynq®
UltraScale+™ RFSoC Gen-2 / Gen-3 with up to 16 RF-ADC and 16 RF-DAC
channels and up to 6 GHz analog bandwidth.
RFSoC Gen-2 Dev Kit (LTE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
The Avnet Zynq® UltraScale+™ RFSoC Development Kit enables system
architects to explore a 2-channel RF signal chain optimized at 1800
MHz from antenna to digital using tools from MathWorks and industryleading RF components from Qorvo.
RFSoC Gen-3 Dev Kit (mmWave). . . . . . . . . . . . . . . . . . . . . . . . 19
The Avnet Wideband mmWave Radio Development Kit for Xilinx RFSoC
Gen-3 enables system architects to prototype RF applications in the
19 to 31 GHz bands using tools from MathWorks and industry-leading
RF technology from Otava.
Otava mmWave Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
24-40 GHz Beamforming IC (BFIC) Evaluation Board allows users
to characterize the performance of the 24-40 GHz BFIC and to
determine that the BFIC will be the critical phased array chip that
their phased array-based system will be built upon in defense radar,
electronic warfare, satellite communications or 5G applications.
2
Avnet’s Zynq-7000 SOC and Zynq Ultrascale+ MPSoC SOM Solutions
PicoZed
Features
Zynq Device
DDR Memory
UltraZed
-EG4
UltraZed
-EV5
Ultra96-V2
7010
7015
7020
7030
7010
7020
ZU3EG
ZU7EV
ZU3EG
7Z010-1
7Z015-1
7Z020-1
7Z030-1
7Z010-1
7Z020-1
ZU3EG-1
ZU7EV-1
ZU3EG-1
28 K
74 K
85 K
125 K
28 K
85 K
154 K
504 K
154K
1 GB DDR3L
1 GB DDR3L
1 GB DDR3L
1 GB DDR3L
1 GB DDR3
1 GB DDR3
2 GB DDR4
5 GB DDR4
2GB LPDDR4
128 Mb
128 Mb
128 Mb
128 Mb
128 Mb
128 Mb
512 Mb
512 Mb
No
Yes + 16GB card
Programmable
Logic Cells
QSPI
MicroZed
uSD Card Cage
No
No
No
No
Yes
Yes
No
No
eMMC Memory
8 GB
8 GB
8 GB
8 GB
No
No
8 GB
8 GB
No
100/13
135/13
125/13
135/13
100/8
115/8
180/26
152/26
46/14
User I/O1
GTP/GTX/GTR Ports
-
4
-
4
-
-
4 PS
4 PS, 16 PL
4 PS
10/100/1000
Ethernet
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
USB 2.0
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
USB-UART
No
No
No
No
Yes
Yes
Yes
Yes
Yes -- via Pod
Other Peripherals
-
-
-
-
Pmod™
Pmod™
USB 3.0
USB 3.0
USB 3.0, Wi-Fi /
Bluetooth, DisplayPort
Size
4" x 2.25"
102 x 57 mm
4" x 2.25"
102 x 57 mm
4" x 2.25"
102 x 57 mm
4" x 2.25"
102 x 57 mm
4" x 2.25"
102 x 57 mm
4" x 2.25"
102 x 57 mm
3.5" x 2"
89 x 51 mm
4" x 2.5"
102 x 63.5 mm
3.35” x 2.1”
85 x 54 mm
Temperature Grade
Commercial3
Industrial
Commercial3
Industrial
Commercial3
Commercial3
Commercial3
Commercial3
Commercial3
$178 USD
$265 USD
$213 USD
$375 USD
$178 USD
$213 USD
$485 USD
$999 USD
$249 USD
Resale2
1: Zynq: PL IO / PS MIO. 2: Resale based on 1 piece - call for volume pricing. 3: Industrial Grade also available. 4: Custom versions also available in the ZU4EV, ZU4EG, ZU5EV, ZU5EG, and ZU7EG.
Pmod is a registered trademark of Digilent.
Avnet XRF RFSoC SOMs Product Table
Features
XRF16 Gen 2
RFSoC Device
XCZU39DR-2
XCZU47DR-1
XCZU48DR-1
XCZU49DR-2
16
0
0
0
Max Sample Rate (GSPS)
2.22
-
-
-
# of 14-bit RF-ADC w/ DDC
0
8
8
16
Max Sample Rate (GSPS)
-
5
5
2.5
# of 14-bit RF-DAC w/DUC
16
8
Max Sample Rate (GSPS)
6.554
8.92
0
0
# of 12-bit RF-ADCs w/ DDC
SD-FEC
XRF8 Gen3
XRF16 Gen 3
8
(1)
8.92
16
(1)
8
9.85 (1)
0
RF Input Freq max (GHz)
5
6
6
6
System Logic Cells (K)
930
930
930
930
PL / PS DDR4 Memory
4GB / 4GB
4GB / 4GB
4GB / 4GB
4GB / 4GB
QSPI Flash Memory
128 MB
128 MB
128 MB
128 MB
eMMC Memory
32 GB
32 GB
32 GB
32 GB
Programmable RF PLL Subsystem
Yes
Yes
Yes
Yes
Multi-module sync
Yes
Yes
Yes
Yes
GTY Ports (28 Gbps)
16
16
16
16
10/100/1000 Ethernet
Yes
Yes
Yes
Yes
USB 3.0
Yes
Yes
Yes
Yes
72 / 24
72 / 24
72 / 24
72 / 24
10/25/100 GbE
10/25/100 GbE
10/25/100 GbE
10/25/100 GbE
Xilinx Aurora
Xilinx Aurora
Xilinx Aurora
Xilinx Aurora
PCIe Gen3
PCIe Gen3/4
PCIe Gen3/4
PCIe Gen3/4
4.0” x 5.0” 101 x 127 mm
4.0” x 5.0” 101 x 127 mm
4.0” x 5.0” 101 x 127 mm
4.0” x 5.0” 101 x 127 mm
Industrial
Industrial
Industrial
Industrial
$21,995
$22,995
Call
$24,995
User I/O (2)
High Speed Data Transport
3
Size
Temperature Grade
Resale (4)
1: For operation up to 10GSPS, contact your local Avnet Sales Representative. 2: RFSoC: PL IO / PS MIO. 3: RFSoC integrated 100GbE and PCIe blocks are not provisioned in standard
Avnet XRF IP/reference designs. Custom design services are available. 4: Resale based on 1 piece - call for volume pricing.
3
MINIZED ™
MiniZed™ is a single-core Zynq 7Z007S development board that targets entrylevel Zynq developers with a low-cost prototyping platform. With the advent of
the latest cost-optimized portfolio from Xilinx, this board targets entry-level Zynq
developers with a low-cost prototyping platform.
This compact design features on-board connectivity through USB, Wi-Fi and
Bluetooth. Peripherals can be plugged into dual Pmod-compatible connectors,
the Arduino-compatible shield interface or the USB 2.0 host interface. JTAG
circuitry is incorporated onto the MiniZed base board, so with a single micro-USB
cable to your laptop you are already up and running. User LED’s, a button and a
switch allow for a physical board interface.
MiniZed provides for an efficient hardware reference design, while it is also an
inexpensive board that can be used to run workshops and tutorials. The board
aims to showcase the power of Zynq, where the Cortex A9 processor core
integrates seamlessly with the programmable fabric to provide signal processing
and control solutions. The on-board digital microphone serves as an input for a
variety of illustrations of how to implement FIR filters, FFT’s and direct
memory access.
Features
Xilinx Zynq XC7Z007S SoC
- Micron 512 MB DDR3L
- Micron 128 Mb QSPI flash
- Micron 8GB eMMC mass storage
- On-board USB to JTAG and debug UART circuit
- Murata “Type 1DX” wireless module with 802.11b/g/n
Wi-Fi and Bluetooth 4.1 plus EDR and BLE
(Bluetooth Low Energy)
Parts
Part number
Description
Resale
AES-MINIZED-7Z007-G
MiniZed™ Single-core Zynq 7Z007S
Development Board
$89 USD*
- USB 2.0 host interface with Microchip USB3320 PHY
- Dialog Semiconductor DA9062 PMIC (Power
Management IC)
- Arduino-compatible shield interface
*Resale price may be higher in Asia, Australia, New Zealand and Japan
8 GB
eMMC
x16
x4
SDIO
- ST Micro LIS2DS12 Accelerometer and
Temperature sensor
- ST Micro MP34DT05 digital MEMS microphone
Arduino-style
headers
ULPI
PMOD#1
Conn.
PS bi-element
LED
PL bi-element
LED
USB 2.0
PHY
UART
GPIO
LED Driver
UART
JTAG
Xilinx - Zynq
XC7Z007S-1CLG225C
LED Driver
Dual USB
to Serial
PS User Button
PL User Switch
MEMS
Microphone
Reset Button
Reset
Л
33.33MHz
I2C
- Microchip Low-Power Precision CMOS Oscillators
WiFi Active
Kit includes
BT Active
Micro AB
To
Computer
- MiniZed development board
Ready
Done
Boot Mode Switch
Motion &
Temp Sensor
Type A
USB
peripherals
WiFi &
Bluetooth
Module
SDIO
www.minized.org
PMOD#2
Conn.
- Reset button, user button, user switch, 2 x user
bi-element LEDs
OSC
24MHZ
I2C
Power Source
Select
Micro AB
5V
128Mb
QSPI
Integrated
DC/DC Solution
& RTC
0.675V
1.0V
1.35V
1.8V
3.3V
512 MB
DDR3L
- 2 x Pmod-compatible interfaces
Power
External
Power
Supply
- Voucher for SDSoC license from Xilinx
- Micro USB cable
Optional add-on items
- Digilent “Pmod SD” for using an SD card
- SD card
Target applications
- Entry level/Low-cost Zynq development environment
- Training, prototyping and proof-of-concept
demo platform
- Wireless design and demonstrations using Wi-Fi
and Bluetooth
- Audio signal processing examples using the
microphone input
- IoT/Cloud connectivity for on-board and
peripheral sensors
Additional information and downloadable documentation
for MiniZed can be obtained at avnet.me/minized
4
MICROZED ™
MicroZed™ is a low-cost SOM that is based on the Xilinx Zynq -7000 SoC. In
addition to the Zynq-7000 SoC, the module contains the common functions and
interfaces required to support the core of most SoC designs, including memory,
configuration, Ethernet, USB, and clocks. On the bottom side of the module,
MicroZed contains two 100-pin I/O headers that provide connection to two
I/O banks on the programmable logic (PL) side of the Zynq-7000 SoC device.
When plugged onto a user designed baseboard or carrier card, these 100-pin
connectors provide connectivity between the Zynq-7000 SoC PL I/Os and the user
circuits on the carrier card. MicroZed also includes on-board power regulation
that supports 5 V input with an option to support 12 V input.
Industrial Temperature MicroZed SOMs are built with components supporting
extended temperatures of -40 to +85 C, with the exception of the use of the
microSD card connector. Due to the configurability of the Zynq device, the user
must perform final temperature testing validation.
Features
SoC
- XC7Z010-1CLG400 or
- XC7Z020-1CLG400
Parts
Part number
Description
Resale
AES-Z7MB-7Z010-SOM-G/
REV-H
MicroZed 7Z010 SOM, C Grade
$178 USD
AES-Z7MB-7Z010-SOM-I-G/
REV-H
MicroZed 7Z010 SOM, I Grade
AES-Z7MB-7Z020-SOM-G/
REV-H
MicroZed 7Z020 SOM, C Grade
$213 USD
AES-Z7MB-7Z020-SOM-I-G/
REV-H
MicroZed 7Z010 SOM, I Grade
$265 USD
- 128 Mb of QSPI Flash
$217 USD
Communications
- 10/100/1000 Ethernet
- USB 2.0 OTG
- USB-UART
User I/O (via dual board-to-board connectors)
- 7Z010 Version
- 108 User I/O (100 PL, 8 PS MIO)
XC7Z010/20-1
CLG400
OSC @ 33.33 MHz
PS Reset
- 1 GB of DDR3 SDRAM
- MicroSD card interface
128 Mb QSPI
1 GB DDR3
Memory
Processing
System
- PL I/O configurable as up to 48 LVDS pairs or 100
single-ended I/O
USB 2.0
ULPI PHY
USB 2.0
Connector
Ethernet
PHY
RJ45
Connector
USB-UART
µUSB
Connector
Other
SD
Transceiver
Micro SD
Card Socket
- 2x6 Digilent Pmod compatible interface providing 8
PS MIO connections for user I/O
User LED
User Push Button
- 7Z020 Version
- 123 User I/O (115 PL, 8 PS MIO)
- PL I/O configurable as up to 55 LVDS pairs or 115
single-ended I/O
- Xilinx PC4 JTAG configuration port
- PS JTAG pins accessible via Pmod or I/O headers
- 33.33 MHz oscillator
Pmod™ (8 PS MIO)
PC4 Header
- User LED and push button
Software
JX1 Micro Header
50/58 User I/O (7Z010/7Z020)
Programmable
Logic
JX2 Micro Header
50/57 User I/O (7Z010/7Z020)
- Linux BSP and reference designs
Mechanical
- 4 inches x 2.25 inches (102 mm x 57 mm)
Additional information and downloadable documentation
for MicroZed can be obtained at avnet.me/microzed
5
MICROZED ™ ACCESSORIES
MicroZed I/O Carrier Card
Part number
Resale
SURL
AES-MBCC-IO-G
$149 USD
avnet.me/mz-io-cc
The I/O Carrier Card supports the System-on-Module (SOM), providing easy access to the full 108 user I/O available from the MicroZed
SOM. Two 100- pin MicroHeaders on the carrier card mate with the MicroZed, connecting over 80 of the MicroZed Programmable Logic (PL)
I/O to 12 Digilent Pmod™ compatible interfaces. The remaining MicroZed I/O are connected to various I/O Carrier Card features, including
push button switches, DIP switches, LEDs, EEPROM, Xilinx XADC, and clock oscillator. The I/O Carrier Card also generates the necessary
power rails for MicroZed, providing 5 V to the MicroZed core, user selectable bank voltages for the PL I/O, and the necessary voltages for
the XADC. The I/O Carrier Card speeds prototype and evaluation of MicroZed and provides an excellent starting point for creating your
own MicroZed carrier card.
MicroZed FMC Carrier Card
Part number
Resale
SURL
AES-MBCC-FMC-G
$199 USD
avnet.me/mz-fmc-cc
The FMC Carrier Card supports the System-on-Module (SOM), providing easy access to the full 108 user I/O available from the MicroZed
SOM. Two 100-pin MicroHeaders on the carrier card mate with the MicroZed, connecting 75 of the MicroZed Programmable Logic (PL) I/O to
a low-pin-count Vita 57 FPGA Mezzanine Connector (FMC) interface. The remaining MicroZed I/O are connected to various FMC Carrier Card
features, including push button switches, LEDs, EEPROMs, and five Digilent Pmod compatible interfaces. The FMC Carrier Card also generates
the necessary power rails for MicroZed, providing 5 V to the MicroZed core and a user selectable bank voltage for the PL I/O and FMC Vadj.
The FMC Carrier Card accelerates complex prototyping by interconnecting a MicroZed SOM and industry-standard FMC Modules.
MicroZed Arduino Carrier Card
Part number
Resale
SURL
AES-ARDUINO-CC-G
$89 USD
avnet.me/mz-arduino-cc
The MicroZed™ Carrier Card Kit for Arduino™ brings both Shield expansion and Peripheral Module expansion (2x6 pin connectors) to the MicroZed
System-On-Module. The carrier card is ideal for building quick prototypes that leverage the large number of Arduino-compatible Shields.
This low-cost platform facilitates:
- Expansion of platform functionality via a wide range of 3rd party Arduino™-compatible “Shields”
- Design partitioning to include ultra low-power MCU to offload and control the Apps Processor
- Power management and scheduling of the MicroZed board by an optional Microcontroller board
- 2x6 Peripheral expansion connectors for MicroZed as well as the optional MCU sub-system
6
PICOZED ™
PicoZed™ is a highly flexible, rugged SOM that is based on the Xilinx Zynq-7000
SoC. It offers designers the flexibility to migrate between the 7010, 7015, 7020,
and 7030 Zynq-7000 SoC devices in a pin-compatible footprint. The PicoZed
module contains the common functions required to support the core of most SoC
designs, including memory, configuration, Ethernet, USB, clocks, and power. It
provides easy access to over 100 user I/O pins through three I/O connectors on
the backside of the module. These connectors also support access to dedicated
interfaces for Ethernet, USB, JTAG, power and other control signals, as well as
the GTP/GTX transceivers on the 7015/7030 models. The transceiver based 7015
and 7030 versions of PicoZed are a superset of the 7010/7020 version, adding
four highspeed serial transceiver ports to the I/O connectors. Designers can
simply design their own carrier card, plug-in PicoZed, and start their application
development with a proven Zynq-7000 SoC sub-system.
Industrial Temperature PicoZed SOMs are built with components supporting
extended temperatures of -40 to +85 C. Due to the configurability of the Zynq
device, the user must perform final temperature testing validation.
Parts
Features
SoC options
- XC7Z010-1CLG400
- XC7Z015-1CLG485
- XC7Z020-1CLG400
- XC7Z030-1SBG485
Memory
- 1 GB of DDR3L SDRAM
- 8 GB eMMC
Part number
Description
Resale
1-99
AES-Z7PZ-7Z010-SOM-G/REV-E
PicoZed 7010 SOM, C Grade
$178 USD
AES-Z7PZ-7Z010-SOM-I-G/REV-E
PicoZed 7010 SOM, I Grade
$217 USD
AES-Z7PZ-7Z015-SOM-I-G/REV-E
PicoZed 7015 SOM, I Grade
$265 USD
AES-Z7PZ-7Z020-SOM-G/REV-E
PicoZed 7020 SOM, C Grade
$213 USD
AES-Z7PZ-7Z020-SOM-I-G/REV-E
PicoZed 7020 SOM, I Grade
$265 USD
- 113 User I/O (100 PL, 13 PS MIO)
AES-Z7PZ-7Z030-SOM-I-G/REV-E
PicoZed 7030 SOM, I Grade
$375 USD
- PL I/O configurable as up to 48 LVDS
- 128 Mb of QSPI Flash
Communications
- 10/100/1000 Ethernet PHY
- USB 2.0 OTG PHY
User I/O (via three board-to-board connectors)
- 7Z010 Version
- pairs or 100 single-ended I/O
- 7Z015 Version
*Contact your local Avnet sales office for pricing on higher quantities
- 148 User I/O (135 PL, 13 PS MIO)
128 Mb QSPI
OSC @
33.33 MHz
1 GB DDR3L
XC7Z010/20-1
CLG400
8 GB eMMC
JX1 Micro Header
50/58 User I/O
(7Z010/7Z015-20-30)
JX2 Micro Header
50/57 User I/O
(7Z010/7Z015-20-30)
XC7Z015/30-1
CLG485/
SBG485
Programmable
Logic
USB 2.0
ULPI PHY
Ethernet
PHY
- PL I/O configurable as up to 65 LVDS pairs or 135
single-ended I/O
- 4 GTP Transceivers
- 7Z020 Version
- 138 User I/O (125 PL, 13 PS MIO)
- PL I/O configurable as up to 60 LVDS pairs or 125
single-ended I/O
- 7Z030 Version
JX3 Micro Header
Ethernet / USB 2.0 OTG
10/20 User I/O
(7Z020/7Z015‐30)
4 GTP/GTX Ports
(7Z015/7Z030)
- 148 User I/O (135 PL, 13 PS MIO)
- PL I/O configurable as up to 65 LVDS
- pairs or 135 single-ended I/O
- 4 GTX Transceivers
Other
- JTAG configuration port accessible via I/O
connectors
PicoZed Carrier Card v2
Part number
Resale
SURL
AES-PZCCFMC-V2-G
$349 USD
avnet.me/pz-fmc-v2-cc
- PS JTAG pins accessible via I/O connectors
- 33.33 MHz oscillator
Software
- Linux BSP and reference designs
Mechanical
- 4 inches x 2.25 inches (102 mm x 57 mm)
Additional information and downloadable documentation
for PicoZed can be obtained at avnet.me/picozed
7
ULTRA96™-V2
The Ultra96-V2 is an Arm-based, Xilinx Zynq UltraScale+™ MPSoC single board
computer based on the Linaro 96Boards Consumer Edition (CE) specification.
Ultra96-V2 is available in many countries around the world as it has been designed
with a certified radio module from Microchip. Additionally, Ultra96-V2 is available
in both commercial and industrial temperature grade options. Additional power
control and monitoring is possible with the included Infineon PMICs.
The Ultra96-V2 boots from the provided Delkin 16 GB microSD card. Engineers
have options of connecting to Ultra96-V2 through a Webserver using integrated
wireless access point capability or to use the provided Linux windows
environment which can be viewed on the integrated Mini DisplayPort video
output. Multiple application examples and on-board development options are
provided as examples.
Ultra96-V2 provides four user-controllable LEDs. Engineers may also interact
with the board through the 96Boards-compatible low-speed and high-speed
expansion connectors by adding peripheral accessories such as those included in
the MikroE Click Mezzanine for 96Boards (available as an accessory).
Features
MPSoC
- Xilinx Zynq UltraScale+ MPSoC ZU3EG A484
Memory
Micron LPDDR4 memory provides 2 GB of RAM in a 512M x 32 configuration.
Wireless options include 802.11b/g/n Wi-Fi and Bluetooth 5 Low Energy. The radio
module is Agency Certified in over 75 countries. UARTs are accessible on a header
as well as through the expansion connector. JTAG is available through a header.
The convenient JTAG/UART Pod (available as an accessory) provides both JTAG
and UART connections via USB. I2C is available through the expansion connector.
- Micron 2 GB (512M x32) LPDDR4 Memory
Two Microchip USB3320 USB 2.0 ULPI Transceivers and one Microchip USB5744
4-Port SS/HS USB Controller Hub enable multiple USB connections. Ultra96-V2
provides one upstream (device) and two downstream (host) USB 3.0 connections.
A USB 2.0 downstream (host) interface is provided via the high-speed expansion.
- 1x USB 3.0 Type Micro-B upstream port
An IDT VersaClock 6E clock generator provides timing for USB 3.0, USB 2.0,
DisplayPort, and the Xilinx MPSoC primary clock input.
The integrated Infineon programmable power regulators generate all on-board
voltages from an external 12V supply (available as an accessory) as well as
providing access to power telemetry through PMBus connectivity.
Related parts
- Delkin 16 GB microSD card + adapter
- Embedded Linux available via download
Communications and UI
- Microchip Wi-Fi / Bluetooth
- Mini DisplayPort (MiniDP or mDP)
- 2x USB 3.0, 1x USB 2.0 Type A downstream ports
User I/O
- 40-pin 96Boards Low-speed expansion header
- 60-pin 96Boards High-speed expansion header
Other
- IDT programmable LVDS and Single-ended clocks
- Infineon and ON Semiconductor voltage regulators
- Linaro 96Boards Consumer Edition compatible
Mechanical
Part number
Description
Resale
AES-ULTRA96-V2-G
ZU3EG Single Board Computer
(Commercial Temp)
$249 USD
AES-ULTRA96-V2-I-G
ZU3EG Single Board Computer
(Industrial Temp)
$499 USD
- 85mm x 54mm form factor
*Contact your local Avnet sales office for pricing on higher quantities.
Additional information and downloadable documentation
for Ultra96-V2 can be obtained at avnet.me/ultra96v2
8
ULTRA96™ ACCESSORIES
USB-to-JTAG/UART Pod
Part number
Resale
SURL
AES-ACC-U96-JTAG
$39 USD
avnet.me/ultra96jtag
The Ultra96 USB-to-JTAG/UART Pod is an inexpensive and convenient way to add both USB-to-UART and Xilinx USB-to- JTAG capability.
With a single microUSB connection to the host, this pod provides the transceivers to communicate with both the UART and JTAG headers
on Ultra96. This then allows engineers to access a serial terminal and Xilinx JTAG tools for communication, debugging, and simulation.
External 96 Boards Compliant Power Supply Kit
Part number
Resale
SURL
AES-ACC-U96-4APWR
$19.99 USD
avnet.me/96Board4APower
The External 96Boards Compliant Power Supply Kit is the highest power 96Boards-compatible power supply from Avnet that supplies 12V @
4A. It ships with an international plug set and supports 100-240 VAC. This power supply is recommended for power through the expansion
mezzanines or USB 3.0 host connectors.
96Boards Click Mezzanine
Part number
Resale
SURL
AES-ACC-U96-ME-MEZ
$16 USD
avnet.me/click-mezz
The 96Boards Click Mezzanine allows engineers to connect their low-speed (LS) mezzanine to Click Boards. The mezzanine breaks out the
LS header to two MikroBUS sites, each supporting one Click board. Through common interfaces such as UART, SPI, and I2C, the MikroBUS
standard offers many 100’s of sensor, display, storage, timing, mixed-signal, and audio Click board.
96Boards Click Mezzanine Starter Kit
Part number
Resale
SURL
AES-ACC-U96-ME-SK
$49 USD
avnet.me/click-mezz-bundle
The 96Boards Click Mezzanine Starter Kit bundles the 96Boards Click Mezzanine with three Click boards that adds 6 Degree-of-freedom
Inertial Measurement,2x16 Character Display, and USB-UART.
On-Semi Dual Camera Mezzanine
Part number
Resale
SURL
AES-ACC-U96-ONCAM-MEZ
$199 USD
avnet.me/U96DualCameraMezz
This 96Boards mezzanine card features two Polight IAScompatible imaging modules based on imaging sensors from ON Semiconductor.
These sensors interface to an AP1302 imaging co processor. By using the 96Boards standard, this card is easily added to the Ultra96-V2
platform. This kit simplifies the complex process of developing with imaging sensors.
MIPI-CSI2 is widely used in the consumer industry for high-speed communications from host processor to image sensors, but many image
sensor modules have varying connector formats which can lead to difficulties with experimenting with different camera modules. The
Imager Access System (IAS) image sensor module format from ON Semiconductor provides access to all image sensor modules that are
compatible within the IAS standard.
Ultra96-V2 Heatsink
Part number
Resale
SURL
AES-ACC-U96-PHS-1
$10 USD
avnet.me/ultra96-heatsink
Passive heatsink for the Ultra96-V2. This part may be used to replace the bracket/fan assembly on Ultra96-V2 Rev 1 with a date code earlier
than 1940 (built prior to 40th week of 2019).
9
ULTRAZED-EG™
UltraZed-EG™ SOM is a highly flexible, rugged, System-On-Module (SOM) based
on the Xilinx Zynq UltraScale+™ MPSoC. Designed in a small form factor, the
UltraZed-EG SOM packages all the necessary functions such as system memory,
Ethernet, USB, and configuration memory needed for an embedded processing
system. The UltraZed-EG provides easy access to 180 user I/O pins, 26 PS MIO
pins, and 4 high-speed PS GTR transceivers along with 4 GTR reference clock
inputs through three I/O connectors on the backside of the module.
Designers can simply design their own carrier card, plug-in UltraZed-EG SOM, and
start their application development with a proven Zynq UltraScale+ MPSoC subsystem. Available with the Zynq UltraScale+ MPSoC XCZU3EG-1SFVA625 device,
the UltraZed-EG SOM enables designers to build high performance systems with
confidence and ease. By simply plugging the off-the-shelf UltraZed-EG SOM into
an application specific carrier card, system bring-up and debug time can be cut in
half, while overall system cost can be reduced by 20% or more versus a standard
chip-down design.
- Xilinx XCZU3EG-1SFVA625 device
- Other options are available with MOQ=100
Memory
- DDR4 SDRAM (2GB, in x32 configuration)
- Dual QSPI Flash (64MB)
- eMMC Flash (8GB, in x8 configuration)
Part number
Description
Resale
1-99
AES-ZU3EG-1-SOM-G
UltraZed-EG SOM (Commercial Temp)
$485 USD
AES-ZU3EG-1-SOM-I-G
UltraZEd-EG SOM (Industrial Temp)
$535 USD
*Contact your local Avnet sales office for pricing on higher quantities
PS-Side
DDR4
(2GB, x32)
MIO[0:12]
eMMC
(8GB, x8)
MIO[13:22]
INT-MIO[23]
I2C 8-Bit
I/O Expander
- USB 2.0 ULPI PHY
- Gigabit Ethernet PHY
Other
- On-board voltage regulators
HP I/O (90)
- Power-On Reset (POR) circuit
140-Pin Connector (JX1)
Signal(90), GND(37), VCCO(6),
VIN(3), JTAG(4)
Dual QSPI
(64MB)
Communications
- PS reference clock input
PL-Side
PS_REF_CLK
PS Reference
Clock
JTAG (4)
I2C EEPROM
(2Kb)
- 4-position boot mode slide switch
- Heatsink included
User I/O (via three board-to-board connectors)
- 3 JX micro-header connectors (2 x 140-pin, 1 x
100-pin) providing the following connections to
the Carrier Cards
- 180 user PL I/O pins
- 26 user PS MIO pins (one full MIO bank)
- 4 PS GTR transceivers
- 4 PS GTR reference clock inputs
12C-MIO[24:25]
Zynq UltraScale+
ZU3EG-SFVA625
2-Channel
I2C Switch/
MUX
SD1/SC1
SD0/SC0/INT0
HP I/O (66)
To PMBus
Regulators
HD I/O (24)
3
26
5
10
16
8
MIO[26:51]
USB 2.0
ULPI PHY
SYSMON (4)
MIO[52:63]
PMBus (3)
Ethernet
RGMII PHY
140-Pin Connector (JX2)
Signal(90), GND(31), VCCO(6),
VIN(3), SYSMON(4), PMBus(3)
SOM_RESET_IN, CC_RESET_OUT,
SOM_PG_OUT
SDA/SCL
100-Pin Connector (JX3)
Signal(65), GND(19),
GTRAVCC(3), GTRAVTT(2),
Voltage Feedback Sense(6),
PS_VBATT, CC_SDA, CC_SCL,
CC_INT, VCCO_PSIO_501
MPSoC
- I2C EEPROM (2Kb)
Parts
PS Boot Mode
Switch
Features
MIO[64:77]
- PS JTAG interface
- PL SYSMON interface
- USB 2.0 connector interface
- PMBus interface
- Carrier Card I2C interface
- SOM Reset input
- Carrier Card interrupt input
- Carrier Card Reset output
- Power Good output
GTR[0:3]
GTR_Ref_CLK[0:3]
MODE[0:3]
PMBus Voltage Regulators
Input: 5 - 12V
Outputs:
0.6V, 0.85V, 1.0V, 1.2V,
1.25V, 1.8V, 2.5V, 3.3V
Software
- Linux BSP and reference designs
Mechanical
- 3.5 inches x 2 inches (89 x 51 mm)
Additional information and downloadable documentation
for UltraZed-EG can be obtained at avnet.me/ultrazed-eg
10
ULTRAZED-EG™ ACCESSORIES
UltraZed-EG Starter Kit
Part number
Resale
SURL
AES-ZU3EG-1-SK-G
$995 USD
avnet.me/ultrazed-sk
The UltraZed-EG Starter Kit consists of the UltraZed-EG System-on-Module (SOM) and IO Carrier Card
bundled to provide a complete system for prototyping and evaluating systems based on the Xilinx
powerful Zynq UltraScale+ MPSoC device family.
Kit includes
- UltraZed – EG SOM
- UltraZed IO Carrier Card
- 12V AC/DC Power Supply
- Quick Getting Started Card
- UltraZed-EG SOM Mounting
Hardware
- microSD Card 8GB
- RJ45 Cable
- microUSB Cable
UltraZed-EG IO Carrier Card
Part number
Resale
SURL
AES-ZU-IOCC-G
$499 USD
avnet.me/ultrazed-cc
The UltraZed IO Carrier Card supports the UltraZed-EG System-on-Module (SOM), providing easy
access to the full 180 user I/O, 26 PS MIO, and 4 PS GTR transceivers available from the UltraZedEG SOM via three Micro Headers. Two 140-pin Micro Headers on the carrier card mate with the
UltraZed-EG SOM, connecting 180 of the UltraZed-EG Programmable Logic (PL) I/O to 12 Digilent Pmod
compatible interfaces, Arduino Shield, LVDS Touch Panel interface, push button switches, DIP switches,
LEDs, Xilinx SYSMON, and clock oscillator.
UltraZed-EG PCIe Carrier Card
Part number
Resale
SURL
AES-ZU-PCIECC-G
$499 USD
avnet.me/ultrazed-pcie
The UltraZed PCIe Carrier Card supports the UltraZed-EG System-on-Module (SOM), providing easy
access to the full 180 user I/O, 26 PS MIO, and 4 PS GTR transceivers available from the UltraZed-EG
SOM via three Micro Headers. Two 140-pin Micro Headers on the carrier card mate with the UltraZedEG SOM, connecting 180 of the UltraZed-EG Programmable Logic (PL) I/O to 2 Digilent Pmod™
compatible interfaces, FMC LPC slot, LVDS Touch Panel interface, push button switches, DIP switches,
LEDs, Xilinx SYSMON, and clock oscillator.
11
ULTRAZED-EV™
UltraZed-EV™ SOM is a high performance, full-featured, System-On-Module
(SOM) based on the Xilinx Zynq UltraScale+™ MPSoC EV family of devices.
Designed in a small form factor, the UltraZed-EV SOM on-board dual system
memory, high-speed transceivers, Ethernet, USB, and configuration memory
provides an ideal platform for embedded video processing systems. The
UltraZed-EV provides easy access to 152 user I/O pins, 26 PS MIO pins, 4
highspeed PS GTR transceivers along with 4 GTR reference clock inputs, and 16
PL high-speed GTH transceivers along with 8 GTH reference clock inputs through
three I/O connectors on the backside of the module. These connectors provide
USB 2.0, USB 3.0, PCIe Gen2, DisplayPort, SATA 3.0, FMC-HPC and more! The
MPSoC EV device with its integrated H.264 / H.265 video codec unit is capable of
simultaneous encode and decode up to 4Kx2K (60fps).
Parts
Features
MPSoC
- Xilinx XCZU7EV-1FBVB900 device (SOM also
supports 4EV, 5EV, 4EG, 5EG, or 7EG device
in the FBVB900 package)
Part number
Description
Resale
1-99
Memory
AES-ZU7EV-1-SOM-G
UltraZed-EV SOM (Commercial Temp)
$999 USD
- PL DDR4 SDRAM (1GB, in x16 configuration)
AES-ZU7EV-1-SOM-I-G
UltraZed-EV SOM (Industrial Temp)
$1,199 USD
MIO[0:12]
eMMC
(8GB, x8
MIO[13:22]
49
2
PL SYSCLK
HD I/O (48)
PS_CLK
PS Reference
Clock
64
GTH[0:15]
INT–MIO[23]
12C 8-bit
I/O Expander
12C EEPROM
(3Kb)
GTH_REFCLK[0.7]
12 – MIO[24:25]
SDA/SCL
2-Channel
12C SwitchMux
Zynq UltraScale+
ZU7EV-FBVB900
HP I/O (104)
To PMBus
Regulators
SD1/SC1
SD0/SC0/INTO
JTAG(4)
120-Pin Connector (JX3, 4x30 Pins)
Signal(65), GND(36), GTRAVCC(3),
GTRAVTT(2), Voltage Feedback
Sense(9), PS_VBATT, CC_SDA,
CC_SCL, CC_INT_N,
VCCO_PSIO_501
3
26
MIO[26:51]
5
USB 2.0 MIO[52:63]
ULPI PHY
10
Ethernet MIO[64:77]
RGMII PHY
16
GTR[0.3]
8
GTR_REFCLK[30.3]
- I2C EEPROM (2Kb)
SYSMON (4)
PMBus (3)
16
Communications
DDR4
(1GB, x16)
- USB 2.0 ULPI PHY
- Ethernet PHY
Dual Clock
(300 MHz OSC)
200-Pin Connector (JX2, 4x50 Pins)
IO Signal (128), MGTAVTT(6),
MGTAVCC(6), GND(58),
MGTVCCAUX(2)
Dual QSPI
(64MB)
PL-Side
200-Pin Connector (JX1, 4x50 Pins)
IO Signal (104), VCCO (12), GND(62),
SYSMON(14), CC _RESET_OUT_N,
SOM_PG_OUT, SOM_RESET_IN_N,
PMBus(3), JTAG(4), VIN(*)
PS-Side
- Dual QSPI Flash (64MB)
- eMMC Flash (8GB, x8)
*Contact your local Avnet sales office for pricing on higher quantities
DDR4
(4GB, x64)
- PS DDR4 SDRAM (4GB, in x64 configuration)
Other
- On-board voltage regulators
- PS reference clock input
User I/O (via three board to-board connectors)
- Three JX connectors, providing
- PS JTAG interface
- PL SYSMON interface
- Gigabit Ethernet RJ45 connector interface
- PMBus interface
- Power Good output, input voltages, and
output sense pins
Software
- Linux BSP and reference designs
Mechanical
- 4 inches x 2.5 inches (102 x 63.5 mm)
PMBus Voltage Regulators
Input 5 0 12V
Outouts; 0.6V, 0.85V, 1.0V, 1.2V,
1.25V, 1.8V, 2.5V, 3.3V
Additional information and downloadable documentation
for UltraZed-EV can be obtained at avnet.me/ultrazed-ev
12
ULTRAZED-EV™ ACCESSORIES
UltraZed-EV Starter Kit
Part number
Resale
SURL
AES-ZU7EV-1-SK-G
$1,595 USD
avnet.me/ultrazed-ev-sk
The UltraZed-EV ™ Starter Kit consists of the UltraZed-EV System-on-Module (SOM) and Carrier Card
bundled to provide a complete system for prototyping and evaluating systems based on the Xilinx
powerful Zynq® UltraScale+™ MPSoC EV device family.
Kit includes
- UltraZed-EV SOM
- UltraZed-EV SOM Mounting Hardware
- UltraZed-EV Carrier Card
- microSD Card 8GB
- 12V AC/DC Power Supply
- RJ45 Cable
- Quick Start Card
- microUSB Cable
UltraZed-EV Carrier Card
Part number
Resale
SURL
AES-ZUEV-CC-G
$649 USD
avnet.me/ultrazed-ev-cc
The UltraZed-EV Carrier Card supports the UltraZed-EV System-on-Module (SOM), providing easy
access to the full 152 user I/O, 26 PS MIO, 4 PS GTR transceivers, and 16 GTH transceivers available from
the UltraZed-EV SOM via three Micro Headers. Two 200-pin Micro Headers on the carrier card mate
with the UltraZed-EV SOM, connecting 152 of the UltraZed-EV Programmable Logic (PL) I/O along with
16 GTH transceivers to FMC HPC slot, LVDS Touch Panel interface, SFP+ interface, HDMI In/Out, 3G-SDI
In/Out, push button switches, DIP switches, LEDs, Xilinx SYSMON, clock generators, and 2 Digilent
Pmod compatible interfaces.
13
FMC ACCESSORIES
Network FMC Module
Part number
Resale
SURL
AES-FMC-NETW1-G
$149 USD
avnet.me/fmc-network1
The Avnet Network FMC Module enables Industrial Ethernet digital communications, which is a key component to Industry
4.0 applications. The module is designed to operate with any Avnet or Xilinx base board that is FMC enabled. Utilizing the
dual compatible 10/100/1000 Ethernet PHYs, the Network FMC Module can quickly get you started with Xilinx FPGA and SoC
based designs.
ISM Networking FMC v2 Module
Part number
Resale
SURL
AES-FMC-ISMNET2-G
$250 USD
avnet.me/fmc-ismnet2
The FMC-ISMNET2 enables a variety of digital communication interfaces common to industrial applications, including
Industrial Ethernet. From dual 1588 compatible 10/100 Ethernet PHYs, to CAN, RS232, and RS485, the ISM Networking FMC
can quickly get you started with Xilinx FPGA and SoC based designs.
Multicamera FMC Module
Part number
Resale
SURL
AES-FMC-MULTICAM4-G
$299 USD
avnet.me/fmc-multicam
The Avnet Multi-Camera FMC module supports up to four (4) high definition camera modules using MAXIM Integrated’ s
GMSL technology (Gigabit Multimedia Serial Link), that is widely used in the automotive industry for in-vehicle high speed
communication of video streams.
Quad AR0231AT Camera FMC Bundle
Part number
Resale
SURL
AES-FMC-MC4-AR0231AT-G
$1,699 USD
avnet.me/fmc-quad-cam
The Quad AR0231AT Camera FMC Bundle combines the Avnet Multi-Camera FMC module, four AR0231AT camera modules
with GMSL serialization and a cable assembly as a complete add-on solution for vision-guided applications.
HDMI I/O FMC Module
Part number
Resale
SURL
AES-FMC-HDMI-CAM-G
$250 USD
avnet.me/fmc-hdmi-cam
The FMC-HDMI-CAM FMC module provides high-definition video interfaces for Xilinx FMC-enabled baseboards. An HDMI
video source can provide video content to the module. The module also provides an HDMI output to display FPGA driven
video content. The FMC module also provides a camera interface for optional camera modules.
14
OTHER ACCESSORIES
ZedBoard
Part number
Resale
SURL
AES-Z7EV-7Z020-G
$449 USD
avnet.me/zedboard-dev-kit
ZedBoard is a low-cost development board for the Xilinx Zynq-7000 All Programmable SoC. This board contains everything
necessary to create a Linux, Android, Windows or other OS/RTOS-based design. Additionally, several expansion connectors
expose the processing system and programmable logic I/Os for easy user access.
Infineon TPM v2.0 Peripheral Module
Part number
Resale
SURL
AES-PMOD-TPM20-SLB9670-G
$29.95 USD
avnet.me/tpm2.0
The Trusted Platform Module (TPM) 2.0 Security Peripheral Module (Pmod) enables a root of trust for platform integrity,
remote attestation, and cryptographic services as required by Industrial Internet of Things (IIoT) Applications.
ON Python 1300C Camera Module
Part number
Resale
SURL
AES-CAM-ON-P1300C-G
$499 USD
avnet.me/python1300
The camera module features ON Semiconductor’s PYTHON-1300 color image sensor. The PYTHON-1300 is a 1/2 inch SupereXtended Graphics Array (SXGA) CMOS image sensor with a pixel array of 1280 by 1024 pixels.
Murata 1DX Ble WiFi Bluetooth Pmod WiFi/BLE Module
Part number
Resale
SURL
AES-PMOD-MUR-1DX-G
$59 USD
avnet.me/pmod_1dx
The Murata 1DX Wi-Fi Bluetooth Pmod allows you to add wireless capabilities to your existing development kit. Examples
for ZedBoard and UltraZed-EG Development Kits are provided that show how to enable and use the wireless functions from
PetaLinux software. This product is an evaluation kit and for Development only. This kit should not to be placed on the
Market for resale and is not certified for production use.
JTAG HS3 Programming
Part number
Resale
SURL
210-299P-KIT
$59 USD
avnet.me/jtaghs3
The HS3 builds on the successful JTAG-HS1 by adding an open-drain buffer to pin 14 allowing for the debugging of Xilinx
Zynq-SOC processors. It can be attached to target boards using Xilinx’s 2x7 connector, and is compatible with all Xilinx tools.
15
XRF™ RFSOC
SYSTEM-ON-MODULES
Avnet XRF ™ RFSoC System-on-Modules are designed for large-scale
integration into deployed RF systems demanding small footprint, low
power, and real-time processing. XRF modules feature the Xilinx Zynq®
UltraScale+™ RFSoC Gen-2 / Gen-3 with up to 16 RF-ADC and 16 RF-DAC
channels supporting up to 6 GHz analog bandwidth.
Combine the production-ready XRF module with an XRF Carrier Card and
Avalon™ software suite to jump-start proof-of-concept and application
development. Then deploy your system with the same XRF module used for
proof-of-concept. Example code and tutorials demonstrate Xilinx RFSoC
multi-tile sync (multi-converter sync) and multi-module synchronized
analog capture.
Features
XRF16 Gen2 with Xilinx ZU+ RFSoC ZU39DR-2
- 5 GHz analog bandwidth
- 16x ADCs, 12-bit up to 2.22 GSPS
Parts
Part number
Description
Resale
AES-XRF16-ZU39-G
XRF16 Xilinx RFSoC Gen2
System-On-Module
$21,995 USD
AES-XRF8-ZU47-G
XRF8 Xilinx RFSoC Gen3 System-On-Module
$22,995 USD
AES-XRF8-ZU48-G
XRF8 Xilinx RFSoC Gen3
System-On-Module
TBD
AES-XRF16-ZU49-G
XRF8 Xilinx RFSoC Gen3 System-On-Module
$24,995 USD
- 16x DACs, 14-bit up to 6.554 GSPS
XRF16 Gen3 with Xilinx ZU+ RFSoC ZU49DR-2
- 6 GHz analog bandwidth
- 16x ADCs, 14-bit up to 2.5 GSPS
- 16x DACs, 14-bit up to 9.85 GSPS (10 GSPS available)
XRF8 Gen3 with Xilinx ZU+ RFSoC ZU47DR/48DR-1
- 6 GHz analog bandwidth
- 8x ADCs, 14-bit up to 5.0 GSPS
- 8x DACs, 14-bit up to 8.92 GSPS (10 GSPS available)
I2C, SPI
Power
Subsystem
boot
128 MB Flash
storage
32 GB eMMC
PS
PL
4 GB DDR4
24 DIO
High-Speed Data Transfer
UART-USB
- 16x serial links up to 28 Gbps available for 10/25/100
GbE, PCIe Gen 3x16, eCPRI, OCuLink, and Aurora
USB 2.0 PHY
64
Processing
System
1 GbE PHY
4 GTR*
4 GB DDR4
16 GTY*
Programmable
Logic
Programmable
TCXO
SysRef
Fs
28 Gbps/channel
72 DIO
Trigger In
Trigger Out
Fclk
TI LMK/LMX
RF PLLs
& Clock
Management
RF-ADC
RF-DAC
- Quad Mesh™ firmware achieves 4x 61.6 Gbps fullduplex Aurora data exchange, facilitating tiling in
multi-module high performance real-time systems
Clocks & Synchronization
6 Gbps/channel
64
- Optional ZU48DR enables 8x SD-FEC engines
8x or 16x RF-ADC
8x or 16x RF-DAC
Reference In
- Ultra-low jitter programmable sampling clocks using
Texas Instruments LMK/LMX RF PLLs
- External or onboard programmable TCXO
reference clock
- Phase coherent synchronous sampling across all
converters & multiple modules
- External input for PPS and trigger
Memory
- 4 GB DDR4 @ Programmable Logic
- 4 GB DDR4 @ Processor Subsystem
- 32 GB eMMC persistent storage
- 128 MB QSPI boot storage
Reference Out
* Xilinx GTY high-speed serial transceivers available to implement high-speed communication links
including 100GbE, PCIe, Xilinx Aurora. GTR transceiver can implement USB3, SATA, and PCIe.
Additional information and downloadable documentation for the XRF
SOMs can be obtained at avnet.me/xrf-family
16
XRF SOM ACCESSORIES
XRF8 Carrier Card
Part number
Resale
SURL
AES-XRF8-CC-G
$4,995 USD
avnet.me/xrf8-cc
Part number
Resale
SURL
AES-XRF-CC-G
$4,995 USD
avnet.me/xrf16-cc
XRF16 Carrier Card
The XRF Xilinx RFSoC System-on-Modules (SOM) are designed for integration into your deployed system. The XRF Carrier Cards and Avalon
software suite provide a rapid prototype platform, enabling you to develop application code for XRF SOMs that is ready for deployment
when your custom carrier arrives.
The XRF Carrier provides connection to standard SOM peripherals including USB2.0, 1 Gb Ethernet, PCIe, UART, SPI, I2C, GPIO, and JTAG.
High-speed digital connectivity is available through sixteen 28Gbps Xilinx GTY transceivers, enabling standards like PCIe over OCuLink,
10/25/100 GbE, and Xilinx Aurora.
The SOM RF-ADC and RF-DAC ports are made available using Samtec IsoRate connectors that easily convert to SMA with cable adapters.
Synchronization is enabled by external reference clock connection, external in/out triggers, and software examples demonstrating RFSoC
multi-tile sync (multi-converter sync) and multi-board synchronized analog capture.
XRF Fansink Active Cooling Solution
Part number
Resale
SURL
AES-XRF-FANSINK-G
$185 USD
avnet.me/xrf-fansink
Avnet XRF RFSoC System-on-Modules require heat dissipation solutions for most applications. An active heatsink, consisting of a heat
frame plus fansink, was created to meet this need. The heat frame makes a mechanical connection to the RFSoC device via thermal pad.
The entire assembly is secured to the board with precision spacers and screws.
XRF Heatsink Passive Cooling Solution
Part number
Resale
SURL
AES-XRF-HEATSINK-G
$295 USD
avnet.me/xrf-passive-cooling
Avnet XRF RFSoC System-on-Modules require heat dissipation solutions for most applications. A passive heatsink was created to meet
this need within enclosed systems. The AES-XRF-HEATSINK-G kit is compatible with all Avnet XRF modules. The assembly is shown below
attached to an XRF16 Gen2 module, mounted to the XRF16 Carrier.
XRF Samtec Isorate®-to-SMA Breakout Board
Part number
Resale
SURL
AES-XRF-ISORATEBB-G
$285 USD
avnet.me/isorate-board
A compact, high performance breakout board which converts the XRF carrier Samtec Isorate® 8 position connector to 8 standard SMA.
17
ZYNQ® ULTRASCALE+
RFSOC DEVELOPMENT KIT
The Avnet Zynq® UltraScale+™ RFSoC Development Kit enables system architects
to explore the entire signal chain from antenna to digital using tools from MathWorks
and industry-leading RF components from Qorvo. We extend the functionality
of the Xilinx Zynq UltraScale+ RFSoC ZCU111 Evaluation Kit by adding a Qorvo
2-Channel RF Front-end 1.8 GHz Card for over-the-air transmission, plus native
connection to MATLAB® & Simulink® with Avnet’s RFSoC Explorer® application.
Qorvo 2-Channel RF Front-end 1.8 GHz Card
The Qorvo 2-Channel RF Front-end 1.8 GHz Card extends the functionality of
the Xilinx Zynq UltraScale+ RFSoC ZCU111 Evaluation Kit, enabling over-the-air
transmission, plus native connection to MATLAB® & Simulink® with Avnet’s RFSoC
Explorer® application.
Features
- Avnet RFSoC Explorer for Signal Capture & Analysis
with MATLAB and Simulink
- Radio-in-the-loop co-simulation (Gigabit Ethernet)
Parts
Part number
Description
Price
AES-ZU-RFSOC-SK-RVS-G
Zynq® UltraScale+TM RFSoC
$9,495
Development Kit
- Over-the-air testing with 2x2 LTE 1800MHz FDD
front end
- Direct-RF sampling without an external RF mixer
Starter kit includes
- Xilinx Zynq ZCU111 Evaluation Kit
- Qorvo 2-Channel RF Front-end 1.8 GHz Card
- MATLAB® & Simulink® with Avnet’s RFSoC
Explorer® application
Additional information and downloadable documentation for Zynq
UltraScale+ RFSoC Dev Kit can be obtained at avnet.me/rfsockit
18
WIDEBAND mmWAVE
RADIO DEVELOPMENT
KIT FOR RFSOC GEN-3
The Avnet Wideband mmWave Radio Development Kit for RFSoC Gen-3 is ideal
for prototyping RF applications in mmW bands including 5G NR FR2, wireless
backhaul, as well as K/Ka band radar and SATCOM. This platform combines the
Otava DTRX2 Dual Transceiver mmWave Radio Card - jointly developed by Otava
and Avnet - with the Xilinx Zynq UltraScale+™ RFSoC ZCU208 Evaluation Kit.
Explore the entire signal chain from millimeter wave RF to IF sampling in RFSoC
Gen-3 data converters reaching 6 GHz. Native connection to MATLAB and Simulink
is provided by Avnet’s RFSoC Explorer, featuring graphical control of the platform
and intuitive APIs for programmatic access.
Features
Parts
- Features the Zynq UltraScale+ RFSoC ZU48DR
with integrated gigasample data converters and
programmable gain control
Part number
Description
Resale
AES-ZCU208DTRX2-SK-G
Multi-purpose high performance radio
kit for mmWave applications, built on
XilinxZynq UltraScale+ RFSoC Gen-3
ZCU208 evaluation kit
$19,995 USD
Xilinx Zynq UltraScale+ RFSoC ZCU208 Evaluation Kit
- Complete OEM kit including CLK104, XM650, and
XM655 add-on cards
- 8x 14-bit 5 GSPS ADCs
- 8x 14-bit 10 GSPS DACs
- 4GB 64-bit DDR4 programmable logic memory
- 4GB 64-bit DDR4 processor system memory
- RF Mezzanine Card 2.0 interface for RF expansion
RFSoC
Gen3
Programmable
Logic
ZCU208
- FPGA Mezzanine Card (FMC+) interface for
I/O expansion
DTRX2
TX1
2X
RF DAC
19 to 31 GHz
2X
TX2
RF DAC
Processor
System
DDC
CLK104
Clk Ref
RX1
RF ADC
2X
19 to 31 GHz
RF ADC
DDC
2X
RX2
Otava DTRX2 mmWave Radio Card for Xilinx RFSoC
ZCU208 Evaluation Kit
- 2 TX channels up convert from high IF frequencies to
mmWave frequencies
- 2 RX channels down convert from mmWave
frequencies to high IF frequencies
- Independent TX and RX LO PLLs with integrated
frequency synthesizer, onchip VCO, and common
reference from the Xilinx ZCU208 CLK104 module
- Digital Step Attenuators (DSA) for gain control
- Independent signal chain enable/disable for
TDD operation
- TDD and FDD modes supported
- RF band select filters can be added externally based
on operating frequency
- Powered from a single 12V DC connector
Additional information and downloadable documentation for the Wideband
mmWave RFSoC Dev Kit can be obtained at avnet.me/rfsoc-mmwave
19
OTAVA BEAMFORMER IC
EVALUATION KIT
The Otava Beamformer IC Evaluation Kit allows for the rapid evaluation of the
Otava OTBF103, a ground-breaking device for mmW and 5G development, in a
lab environment. The kit includes the Otava Beamformer Evaluation Board, a
MicroZed SOM based on the Zynq 7010 SoC, supporting hardware and a custom
GUI. Using the MicroZed and GUI software, engineers can immediately focus
on manipulating the RF signals and evaluating the Beamformer IC. The control
interface has been fully implemented and the device can be controlled from a PC
using USB or Ethernet.
Features
- Register-level Otava Beamformer IC control
and evaluation
- Re-programmable MicroZed Zynq 7010
implementation with source
Evaluate and explore the OTBF103 Otava Beamformer IC
Otava’s Beamformer IC (BFIC), the OTBF103, is a mmW wideband time-divisionduplexing beamformer. The BFIC consists of eight transmit channels and eight
receive channels in the 24 GHz to 40 GHz frequency range, which encompasses
numerous worldwide 5G bands.
- Save and recall custom configurations
Each channel has individual phase and gain adjustment controls and an onboard 4K byte memory that allows for fast operational steering between 64
programmable positions. An SPI control interface (LVDS or LVCMOS) is used for
programming the 158 registers and memory locations. The BFIC can be evaluated
by using the OTBF103-EVAL board from Otava.
- Radar, EW
- Satellite communications
Avnet implemented the control interface using a MicroZed 7010 Zynq module and
a GUI that runs on a PC. This enables rapid BFIC familiarization without having to
first create custom software.
Target apps
- mmW, small cell, 5G development
Kit includes
Otava Beamformer IC Eval Board
- The OTBF103 Beamformer IC
- High-performance 2.4 mm vertical mount
connectors for all mmW signals
- Terminal blocks for external power
Parts
Part number
Description
Resale
AES-Z7MB-OTVBFIC1SK-G
Otava Beamformer Evaluation Kit
$7,995 USD
- PMOD male headers for digital control
MicroZed 7010 Xilinx Zynq system-on-module (SOM)
- Xilinx Zynq 7010 SoC with dual-core ARM® Cortex™A9-based application processor unit (APU)
- 1 GB DDR3 SDRAM, 128 Mb QSPI flash
Related parts
- 10/100/1000 Ethernet and USB-UART
Part number
Description
Resale
OTBF103
Otava Beamformer IC
Contact sales
OTBF103-EVAL
Otava Beamformer
Evaluation Board
$7,499 USD
Reset Button
Txi
Rxo
Txi
Rxo
- 4GB Micro SD card
- Micro USB cable
Modified MicroZed I/O Carrier Card
- 12 PMOD-compatible interfaces for access to 80
MicroZed user I/O
- 5V @ 3A power supply
- Modified from AES-MBCC-IO-G to support 1.2V
on VCCIO_34
BFIC Eval Board
Two custom cable assemblies from Samtec
Power
Tx1
Tx2
Tx3
Tx4
Tx5
Tx6
Tx7
Tx8
Rx1
Rx2
Rx3
Rx4
Rx5
Rx6
Rx7
Rx8
- Connect digital controls between MicroZed and the
BFIC Eval board
OTBF103
SPI
(LVDS)
Control
C# GUI
I/O Carrier Card
PC
MicroZed
Programmable Logic
Cortex A9
Ethernet
C# Graphical
User
Interface
- Allows access to all 158 BFIC registers 4kByte SRAM
- Graphing of ADC outputs of temperature sensors and
RMS Tx and Rx levels
USB
Text
Files
uSD Card
Additional information and downloadable documentation for the
Otava Eval Kit can be obtained at avnet.me/otavabfic
- Read/write defaults from/to text files
- BFIC diagnostics
20
ACCELERATE TIME TO MARKET
Optimize and simplify your product design process
Avnet AVID offers full service product development solutions including hardware and software design services, PCB layout
services, high-speed design analysis, and prototype assembly and testing for electronic products in the defense, medical,
commercial, consumer, automotive and industrial markets.
Services
- Engineering – HW, SW, RF,
analog, wireless
- Turnkey Design and Manufacturing
- Design Customization
- PCB Design & Simulation
- Consultation – review, debug,
feasibility study, compliance
Areas of expertise
- IoT
- Wireless / RF
- Industrial Controls
- Wireless Charging
- Military / Aerospace
- Medical Devices
- Automotive
Development Tools
- Wireless Charging Design Tools
- Embedded Development Platforms
- IoT Solutions
- Starter / Development kits
CONTACT US
Online: www.avid-tech.com
Email: sales@avid-tech.com
Phone: (330) 487-0770
LOOKING FOR THERMAL SOLUTIONS?
Semiconductors require thermal relief - the importance of the
thermal solution will continue to be a critical piece of any design
Thermal solutions are not just “fans”, the largest component to proper thermal management is the heatsink and
interface material which for most high-performance devices is semi-custom to full custom.
Avnet is focused helping customers
manage their thermal performance by
helping in the selection and design of
thermal relief solutions.
Diagram
- Junction to Ambient — ƟJA
- Sink to Ambient — ƟSA
- Case to Sink — ƟCS
- Junction to Case — ƟJC
CONTACT US
2211 S 47th Street
Phoenix, Arizona 85034
United States of America
1-800-585-1602
Innovation today
starts with software
We help high tech makers
build great software
From hardware to the cloud, our expert software team will help you design, develop, integrate
and secure powerful software systems tailored to your needs.
Embedded System Engineering Services
Supports all the stages of the Software Lifecycle Management
with a total independency on software.
- Tech Consulting & UX
- System Design, Security & Development
- Automation Testing
- Cloud Infrastructure
- Long Term Support
Experience and Integration
- Vivado and PetaLinux Tools to achieve a working embedded
Linux kernel on Zynq/ZU+ platforms.
- Vivado and Vitis tools to run FreeRTOS on Zynq platforms,
modifications on BSP and application to interact with the
programmable logic side.
- Address the bottlenecks in SoC system-level integration
and implementation.
Embedded Linux Development & Debugging
- Linux kernel architecture on Zynq/ZU+.
- Linux drivers for custom FPGA IPs, and write applications to
test and verify them.
- Embedded Linux application debug on various platforms.
- Linux BSP adaptation for the Zynq and Zynq UltraScale+
MPSoC platforms.
CONTACT US
Online: witekio.com
Email: sales@witekio.com
AN AVNET COMPANY
ABOUT AVNET
Avnet is a global electronic components distributor with
extensive design, product, marketing and supply chain
expertise for customers and suppliers at every stage of the
product lifecycle. For the past 100 years, Avnet has helped
its customers and suppliers around the world realize the
transformative possibilities of technology.
Learn more about Avnet at www.avnet.com
Contact information
North America
2211 S 47 th Street
Phoenix, Arizona 85034
United States of America
1-800-585-1602
Europe (Silica)
Gruber Str. 60c
85586 Poing
Germany
+49-8121-77702
1.800.332.8638 / avnet.com
Europe (EBV)
Im Technologypark 2-8
85586 Poing
Germany
http://ebv.com/contact
Japan
Yebisu Garden Place Tower, 23F
4-20-3 Ebisu, Shibuya-ku
Tokyo 150-6023 Japan
eval-kits-jp@avnet.com
+81-(0)3-5792-8210
Asia
151 Lorong Chuan
#06-03 New Tech Park
Singapore 556741
XilinxAPAC@avnet.com
+65-6580-6000
Copyright © 2021 Avnet, Inc. AVNET, “Reach Further” and the Avnet logo are registered
trademarks of Avnet, Inc. All other brands are the property of their respective owners.
LIT# 5424-XLX-Solution-Guide-V1
Download