10 ECDIS questions SIRE
inspectors ask and how to deal
with it?
Written by Capt Rajeev Jassal on May 6, 2020
I cannot tell you how much do I enjoy writing on ECDIS.
I truly feel that ECDIS has made the navigation so much
safer.
Well, many still do not agree with this statement and I
respect their opinion too.
There is definitely merit in their opinion if that is based on
the fact that not many officers are trained to handle the
ECDIS in the right way.
I personally have seen a few officers sweat out in front of
SIRE inspectors when they ask the questions related to
ECDIS.
But they sweat out because they have not been adequately
trained. And even if they wanted to self-train themselves,
there is hardly any user-friendly information available.
But not anymore. No more sweating out for ECDIS questions.
In this blog, we will discuss all that SIRE inspectors ask a
2nd mate during his bridge inspection.
And I will discuss these with respect to JRC ECDIS.
So let us start with our first question.
Question 1: Can you show me the last
passage plan on ECDIS?
This is the first question and this is the most important one
too.
The passage needs to be accurate must follow all the
company requirements and must be in accordance with the
industry guidelines.
I have covered the general passage planning in this blog and
ECDIS passage planning in this one.
Do read these two blogs to get to know about the passage
planning.
But you must cover these areas in the passage plan on
ECDIS.

The route

Parallel index lines

No-Go Areas (not excessively marked)

Wheel over position

Abort point

Marking of bridge watch levels

Position plotting interval and method at each leg

Security levels and the points where vessels need to be
hardened.

Point for notice to the engine room and calling the
master
Question 2: Do you perform a route check?
How do you do it?
Route check is a function of the ECDIS which checks the
route and gives all the alarms for which the route is passing
through any dangers.
The 2nd mate then can check each of these alarms to see if
the route needs to be amended.
To perform the route check, open the route in the table
editor and click on the “Safety Check”.
This would give all the errors in the route. If we select on an
error and click on “Jump” the ECDIS screen will jump to the
area of that error.
2nd Mate can then see if that error is applicable to us or if
the route needs to be amended to avoid that.
2nd Mate needs to check each of these errors one by one to
ensure that our route is safe.
Question 3: How do you make sure your
ENCs are corrected up to date?
To check if the ENCs are corrected up to date on JRC ECDIS,
go to 6.Chart -> ENC update report.
This will show you the status of all the ENCs and the week
number these ENCs are corrected up to.
Go to Summary and it will show you the total number of
ENCs and how many of these are up to date and how many
are not up to date.
If you would like to see the status of ENCs for a particular
route only, make sure to tick the “route filter” and choose
the route from the “select route” dropdown.
This will give the ENC status report for the ENCs for the
chosen route.
Question 4: How do you know if you have all
the required ENCs for the route?
The ENC ordering process depends upon your ENC provider.
For example, chartco would have a different procedure for
ordering the ENCs and NAVTOR has a different procedure.
But once you have ordered, received, and updated ENCs in
ECDIS, we need to check if the ECDIS has all the ENCs for
the next voyage.
Ideally, when we check the ENC update report with route
filter and if any ENC is missing, it would show that in this
report.
And when we go to “Status Report”, this would give a clear
reason for the “ENCs not up to date”.
But with this function, it is only checking ENCs for the route
with the set “Cross-track error” in the ECDIS for that route.
So if we have set the cross-track error as 1NM, this would
only check the ENCs for 1NM from the route.
But that is not enough. We need to have the ENCs for up to
at least for few miles from our route.
I prefer to have ENCs for at least 50NM from our route.
This would mean that in case we need to deviate the ship for
any unforeseen reasons, we still have the ENCs for at least
4-5 hours of the deviation.
One way of checking this is to temporarily increase the
cross-track error limit in the route plan. Then check the ENC
status report with route filter.
If the report shows all ENCs up to date then the ECDIS has
the ENCs for the route and up to the (large) cross-track error
set in the route plan.
But some ECDIS has a limitation of maximum cross-track
error that can be set.
So the other way is to get the list of all the ENCs for the
route from ENC provider software (Chartco/Navtor etc) and
check physically if these are available in the ECDIS.
If your company subscribe to PAYS (Pay as you go), you only
need to check this for ENCs that are not available under
PAYS.
Question 5: How do you plot the Navigation
warnings
I have covered this topic in detail in a different blog.
Read it if you have any doubts about how to plot navigation
warnings on ECDIS.
Most of the SIRE inspectors would want to see the navigation
warnings being plotted with “manual update”.
But I and you know that at least on JRC ECDIS, it is much
easier to plot the navigation warning with the user chart.
The problem with the user chart is that it would not generate
an alarm during the route check feature or when you are
using the look-ahead feature.
So if you are plotting the navigation warning with the user
chart, you must have an answer ready for the SIRE
inspector.
The answer for “how do you make sure that route does not
pass through dangerous navigation warning plotted with user
chart”.
And your answer could be that you check that manually
during the passage planning stage.
Question 6: What IHO presentation library
your ECDIS uses? Can you show me?
In layman’s terms, the IHO presentation library is the set of
instructions to the ECDIS manufacturers about how the
various symbols must be displayed on the ECDIS.
For example, what color, size, and shape of the symbols
must the ECDIS show on ECDIS.
ECDIS manufacturer needs to develop its software as per
these set of guidelines developed by IHO.
From 2nd mate and seafarer’s point of view, we must know
what presentation library version our ECDIS has.
And if that is the latest IHO presentation library?
If the vessel is not able to show this information on the
ECDIS, not only this be a SIRE observation but during PSC
inspections this can be detainable deficiency too.
So let us check what presentation library this JRC ECDIS has.
On the ECDIS screen, right-click and choose “S-57/CMAP/ARCS Information”.
Go to “Chart legend” and there you will get the “Presentation
library version”.
Apart from this, you need to know what is the latest version
of the presentation library so that you know your ECDIS has
the latest version .
We can get the information about the current version of the
presentation library from the IHO website, by contacting the
ECDIS maker or simply by asking your company.
Question 7: How do you plot position from
sources other than GPS?
We need to be able to plot position on ECDIS from sources
other than GPS.
The sources like visual bearings, range/bearings, and
celestial observations.
While the procedures may be different on different ECDIS but
if you are actually using these features to plot positions, it
would be easier for you to show it to the SIRE inspector.
Here is a blog that I wrote on position fixing sometime back
that includes position fixing on ECIDS.
Question 8: What ECDIS safety settings are
entered during arrival to this port?
Here is a detailed article on ECDIS safety settings that I had
written earlier.
I assume that you know everything about ECDIS safety
settings. Like what are these safety settings and what value
to set for these settings in the ECDIS.
If you have any doubts, do read the blog on ECDIS safety
settings first.
But even when 2nd mate knows about safety settings, there
is one mistake that I see them making repeatedly.
The mistake is to keep the safety settings constant for the
voyage.
The ECDIS safety setting needs to be dynamic. These need
to be changed during the voyage even when the vessel’s
draft remains the same.
Usually, the safety settings are calculated with zero height of
the tide.
At the open sea, the vessel’s route must be in safe waters
with these safety settings at zero height of the tide.
But that is not the case with port arrivals and departures.
If the vessel needs to use the height of tide for compliance
with the company’s UKC policy, then the safety settings need
to be changed to include the height of tide too.
Mere doing the UKC calculation with the height of tide is not
enough.
Let us say that for a river port we did the UKC calculation
with the height of tide as 3 meters and UKC is complying
with the company’s UKC policy.
Now, this is the ECDIS route for this river port with initial
safety settings (without the height of tide).
This would be a SIRE observation.
Because while navigating at no point in time we can pass
over the depth less than safety depth.
Let us say the safety depth calculated and entered here was
13 meters. And if the height of tide while passing this point
was 3 meters, we need to adjust (reduce) the safety settings
by 3 meters.
In this case, the same ENC would look like this.
As a practice, we can prepare a list of points (waypoints)
where the safety setting needs to be changed (taking into
account the tide).
Question 9: What procedure you follow
when the route crosses safety contour?
A vessel outside the safety contour is in safe waters.
But that does not mean that all the waters in the safety
contour are not safe.
For example, if we have calculated safety depth as 11 meters
then the nearest safety contour will be 15 meters.
But what if the depths inside the safety contour are in the
range of 13 to 14 meters.
These depths are still safe for us because these are more
than our safety depths.
On ECDIS, the unsafe depths (depths less than safety
depths) are shown in dark black color and safe depths are
shown in grey color.
ECDIS is supposed to give an alarm when the vessel crosses
a safety contour.
But after the vessel has crossed safety contour there would
be no alarm in case the vessel is about to run into danger
such as crossing an unsafe depth.
For this reason, we are required to define the procedure we
would follow after crossing the safety contour to ensure that
ship navigates safely.
There are two methods to choose from.
Method 1: After crossing safety contour, Navigator needs to
be more alert and ensure that the vessel does not run over a
depth lesser than safety depth.
This method is based on the careful review of the navigator
while navigating in the area after crossing the safety contour.
Method 2: Or we can use the 2nd method where during the
planning stage, 2nd mate draws a line with a manual update
separating the safe and unsafe areas.
In this case, we need to use the manual update feature so
that we can get the alarm on the ECDIS if the vessel crosses
this line.
It is also required that the company must document in their
procedures as to which method the bridge team should use.
Some companies may direct the master to choose any of the
above two methods.
Question 10: What is scamin and how do you
use it?
Let us consider a buoy in an ENC.
ENC maker would have defined a minimum (SCAMIN) and
maximum (SCAMAX) scale of ENC at which this buoy would
be visible on the ENC.
Let us say the minimum scale set by the ENC maker is
1:50000.
This means that if you zoom the ENC scale to less than
1:50000, this buoy would not be visible on the ENC.
Likewise, there could be so many other features (certain
soundings, buoys, pipelines, cables, etc) for which ENC
makers have defines a minimum and maximum scale for its
visibility.
However, if we keep the SCAMIN setting to off, irrespective
of how much you zoom in or zoom out, none of these
features will disappear.
Let us first see how to switch it on or off on JRC ECDIS.
Go to Menu 6.Chart -> Settings -> S-57/C-MAP/ARCS
Information
From the option “View Common”, you will find the option to
turn on/off the Scale min under “Chart Symbol”.
But why this feature is given at all?
This is to give an option to the navigator to de-clutter the
screen so that it is more user-friendly during the navigation.
Now the question is what is the correct way to use SCAMIN.
During the passage planning stage, we do not want to miss
any of the features or buoy, etc as we do not want to have
our courses run over these.
So during the planning stage, we are expected to keep the
SCAMIN off.
During navigation, we can keep the SCAMIN to “on” to
declutter the ECDIS screen however if we need to go away
from our intended route for some reason, we must turn off
the SCAMIN to review the area.
Conclusion
Nowadays, ECDIS is the main area of interest for SIRE
inspectors when it comes to bridge/navigation rounds.
Though it may sometimes seem too much to cover in ECDIS
but if you have your basic questions about ECDIS covered,
there is nothing to sweat about for ECDIS.