ACC/Capital Metro
Technical Training
Unit 7
Heating and Air Conditioning
Instructor Guide
ABSTRACT
This guide is intended to assist Austin Community College instructors
responsible for instructing Austin Capital Metro Special Transit Technicians
Heating & Air Conditioning courses. The following topics are covered:
diagnosing engine performance problems, ignition system problems, fuel system
problems, mechanically related performance problems, emission control system
problems, and electronic control systems; maintaining ignitions, fuel systems,
emission control systems, and electronic control systems; and conducting shop
operations. The course outline is organized in the form of duty sheets. Each duty
sheet contains some or all of the following: a performance objective (including a
task, the source of the standard (ACAP competency), and conditions for
performance of the task; suggested teaching activities; a criterion-referenced
measure (including a practical application, and a method of evaluating the
practical application).
These are minimum standards; each instructor is expected to add content and
training objectives to course as needed.
The activities provided are designed to train students in the performance of jobrelevant tasks. All three domains of learning—psychomotor, cognitive, and
affective—are addressed.
Experience has shown that the art of learning can also be taught while
teaching subject matter. People need to learn how to learn. This guide takes
into consideration how students learn and are an efficient way for instructors
to assist them to learn.
Below is a brief explanation of the three domains of learning used in this
course:
Psychomotor:
Any manipulative skill such as things as simple as using a screw driver or
wrench, to installing parts, are examples of manipulative or psychomotor skills.
Cognitive:
To perform psychomotor tasks, students must think. Cognition is what
goes on in the mind about any job being done. The teaching methodology
used in this course provides both the collateral knowledge and the impetus to
apply cognition to psychomotor tasks.
To test their knowledge, students may be required to decide the proper
procedure, method or sequence for performance. This decision making
process or cognitive activity provides the basis for higher thinking skills.
Affective:
In order for training to be affective, there has to be an on- the- job application
of the knowledge. Knowledge and skills, both Psychomotor and Cognitive, will
be connected to the daily jobs of each technician and training provided on
how to make practical application on the job.
Diagnose and Repair A/C
System
Duty: Diagnose and Repair A/C System
PERFORMANCE OBJECTIVE 1
TASK: Evaluate System Performance
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.1.1 - Determine operating conditions of the A/C system using gauges to
evaluate system performance.
ENABLING OBJECTIVES:
Use of A/C system performance charts
Use of A/C pressure gauges
Use of Infrared thermometers
TEACHING ACTIVITIES:
1. Discuss Temperature and Pressure Fundamentals
2. Discuss operation of A/C manifold and gauge set
3. Demonstrate connecting the manifolds and gauge set
4. Discuss stabilizing A/C system procedure
5. Discuss visual checks
6. Discuss appropriate gauge pressure readings
Duty: Diagnose and Repair A/C System
PERFORMANCE OBJECTIVE 2
TASK: Identify refrigerant type
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.1.2 – Identify refrigerant type
ENABLING OBJECTIVES:
Use of refrigerant identifying equipment
TEACHING ACTIVITIES:
1. Discuss properties and usage of R12 refrigerant
2. Discuss properties and usage of R134a refrigerant
3. Discuss properties and usage of R22 refrigerant
4. Discuss use of substitute refrigerants
5. Discuss use of refrigerant identifying equipment
6. Demonstrate use of refrigerant identifying equipment
Duty: Diagnose and Repair A/C System
PERFORMANCE OBJECTIVE 3
TASK: Performance test A/C system; diagnose A/C system
malfunctions using principles of refrigeration
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.1.3 –Conduct a performance test of the A/C system to determine necessary
action
ENABLING OBJECTIVES:
Use of A/C system performance charts
Use of A/C pressure gauges
Use of Infrared thermometers
TEACHING ACTIVITIES:
1. Discuss A/C system performance tests
2. Demonstrate a proper A/C system performance tests
Duty: Diagnose and Repair A/C System
PERFORMANCE OBJECTIVE 4
TASK: Diagnose abnormal operating noises in the A/C system
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.1.4 - Diagnose abnormal operating noises in the A/C system; determine
necessary action
ENABLING OBJECTIVES:
Use of A/C system performance charts
Use of A/C pressure gauges
Use of electronic listening devices
TEACHING ACTIVITIES:
1. Discuss causes of A/C system abnormal noises
2. Demonstrate methods of locating A/C system abnormal noises
Duty: Diagnose and Repair A/C System
PERFORMANCE OBJECTIVE 5
TASK: Leak test A/C system
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.1.5 - Leak test A/C system; determine necessary action
ENABLING OBJECTIVES:
Use of leak testing equipment
TEACHING ACTIVITIES:
1. Discuss possible causes of refrigerant leaks
2. Discuss most likely sources of refrigerant leaks
3. Demonstrate methods of locating refrigerant leaks
Duty: Diagnose and Repair A/C System
PERFORMANCE OBJECTIVE 6
TASK:
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.1.6 - Inspect the condition of discharged oil; determine
necessary action
ENABLING OBJECTIVES:
Use of refrigerant recovery equipment
TEACHING ACTIVITIES:
1. Discuss refrigerant oil types and grades
2. Discuss classifications of refrigerant oil
3. Discuss measuring refrigerant oils
4. Demonstrate refrigerant oil inspection
Duty: Diagnose and Repair A/C System
PERFORMANCE OBJECTIVE 7
TASK: Determine recommended oil for system application
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.1.7 - Determine recommended oil for system application
ENABLING OBJECTIVES:
Use of refrigerant oil charts
TEACHING ACTIVITIES:
1. Demonstrate method of determining correct refrigerant oil for system
Duty: Diagnose and Repair A/C System
PERFORMANCE OBJECTIVE 8
TASK: Measure and add refrigerant oil as needed
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.1.8 - Measure and add refrigerant oil as needed
ENABLING OBJECTIVES:
Use of measuring devices
TEACHING ACTIVITIES:
1. Demonstrate procedure for measuring and adding refrigerant oil
Diagnose and Repair A/C
System Components
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 9
TASK: Inspection of A/C condenser
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.1- Inspect A/C condenser for airflow restrictions, performing necessary action.
ENABLING OBJECTIVES:
Understand inspection criteria
TEACHING ACTIVITIES:
1. Discuss causes of condenser airflow restrictions
2. Perform condenser airflow restriction inspection
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 10
TASK: Diagnose thermal protection devices
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.2 - Diagnose A/C system conditions that cause the protection devices
(pressure, thermal, and PCM) to interrupt system operation;
determine necessary action
ENABLING OBJECTIVES:
Understand test results
Use of Multimeter
Use of A/C pressure gauges
TEACHING ACTIVITIES:
1. Discuss operation of A/C pressure protection devices
2. Discuss operation of A/C thermal protection devices
3. Discuss causes of PCM interruption of system operation
4. Demonstrate testing of A/C protection devices
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 11
TASK: Evaluating A/C drive belt condition
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.3 - Inspect A/C compressor drive belts; determine
necessary action.
ENABLING OBJECTIVES:
TEACHING ACTIVITIES:
1. Discuss causes of drive belt failure
2. Discuss v-belt inspection criteria
3. Discuss serpentine belt inspection criteria
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 12
TASK: Evaluating A/C clutch component operation
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.4 - Inspect, test, and/or replace A/C compressor clutch
components and/or assembly.
ENABLING OBJECTIVES:
Understanding test results
Use of multimeter
Use of compressor clutch tools
TEACHING ACTIVITIES:
1. Discuss operation of A/C compressor clutch and components
2. Demonstrate testing procedures of A/C clutch and components
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 13
TASK: Removal and replacement of A/C compressor
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.5 - Remove and reinstall A/C compressor and
mountings; measure oil quantity; determine necessary
action.
ENABLING OBJECTIVES:
Use of proper hand tools
Use of refrigerant recovery equipment
TEACHING ACTIVITIES:
1. Discuss steps necessary to remove and install A/C compressor
2. Demonstrate compressor removal and installation
3. Demonstrate measurement of compressor refrigerant oil
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 14
TASK: Flushing A/C system
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.6 – Flush system of contaminates with approved flush
ENABLING OBJECTIVES:
Use of A/C flushing equipment
TEACHING ACTIVITIES:
1. Discuss causes of A/C system contamination
2. Discuss flushing solvents
3. Demonstrate approved flushing procedure
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 15
TASK: Servicing A/C system mufflers, hoses fitting, O-rings and service
valves
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.7 - Remove and inspect A/C system mufflers, hoses, lines, fittings,
O-rings, seals, and service valves; perform necessary action.
.
ENABLING OBJECTIVES:
Use of A/C hose and fitting tools
TEACHING ACTIVITIES:
1. Discuss A/C fittings hoses and o-rings and service fittings
2. Demonstrate use of special A/C fittings tools
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 16
TASK: Service receiver/drier or accumulator/drier
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.8 - Remove and reinstall receiver/drier or accumulator/drier; measure oil
quantity; determine necessary action.
ENABLING OBJECTIVES:
Use of A/C service tools
TEACHING ACTIVITIES:
1. Discuss operation and failure criteria of receiver/drier
2. Discuss operation and failure criteria of accumulator/drier
3. Demonstrate removal and reinstallation receiver/drier or
accumulator/drier
4. Demonstrate measurement of refrigerant oil
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 17
TASK: Service of expansion valve or orifice (expansion) tube
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.9 - Remove and install expansion valve or orifice (expansion) tube
ENABLING OBJECTIVES:
Use of A/C special service tools
TEACHING ACTIVITIES:
1. Demonstrate Removal and installation of expansion valve or orifice
(expansion) tube
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 18
TASK:
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.10 – Determine need for A/C system filter; perform necessary action.
ENABLING OBJECTIVES:
(Fill here)
TEACHING ACTIVITIES:
1. (Fill here)
Duty: Diagnose and Repair A/C System Components
PERFORMANCE OBJECTIVE 19
TASK:
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.2.11 - Inspect evaporator housing water drain; perform
necessary action.
ENABLING OBJECTIVES:
(Fill here)
TEACHING ACTIVITIES:
1. (Fill here)
Diagnose and Repair Heating,
Ventilation, and Engine Cooling
System
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 20
TASK: Service cooling system
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.1 - Perform cooling system, cap, and recovery system
tests (pressure, combustion leakage, and temperature);
determine necessary action.
ENABLING OBJECTIVES:
Use of cooling system pressure tester
Use of combustion gas detection tools
TEACHING ACTIVITIES:
1. Discuss operation of cooling system, thermostat, cap, and recovery
system
2. Demonstrate use of cooling system pressure tester to test cooling
system
3. Demonstrate use of cooling system pressure tester to test pressure
cap
4. Demonstrate use of cooling system combustion gas test
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 21
TASK: Inspection and service of cooling system hoses
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.2 - Inspect engine cooling and heater system hoses and
belts; perform necessary action.
ENABLING OBJECTIVES:
Understanding inspection criteria
TEACHING ACTIVITIES:
1. Discuss Inspection of engine cooling and heater system hoses
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 22
TASK: Testing and servicing thermostat
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.3 - Inspect, test, and replace thermostat and housing.
ENABLING OBJECTIVES:
Use of proper hand tools
Use of thermometer
TEACHING ACTIVITIES:
1. Discuss thermostat operation
2. Demonstrate thermostat test
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 23
TASK: Coolant service
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.4 - Determine coolant condition and coolant type for
vehicle application; drain and recover coolant
ENABLING OBJECTIVES:
Use of coolant tester
TEACHING ACTIVITIES:
1. Discuss coolant types and applications
2. Demonstrate use of coolant concentration tester
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 24
TASK: Drain and recover coolant
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.5 - Drain and recover coolant
ENABLING OBJECTIVES:
Use of coolant recovery equipment
TEACHING ACTIVITIES:
1. Discuss coolant environmental hazards and regulations
2. Demonstrate use of coolant recovery equipment.
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 25
TASK: Flush coolant system
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.6 - Flush system
ENABLING OBJECTIVES:
Use of coolant flushing equipment
TEACHING ACTIVITIES:
1. Demonstrate coolant flushing procedure
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 26
TASK: Refill system with recommended coolant
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.7 - Refill system with recommended coolant
ENABLING OBJECTIVES:
TEACHING ACTIVITIES:
1. Refill system with recommended coolant
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 27
TASK: Bleed cooling system
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.8 - Bleed system
ENABLING OBJECTIVES:
TEACHING ACTIVITIES:
1. Bleed cooling system
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 28
TASK: Inspect and test cooling fan, fan clutch, fan shroud,
and air dam
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.9 - Inspect and test cooling fan, fan clutch, fan shroud,
and air dams; perform necessary action
ENABLING OBJECTIVES:
Use of proper hand tools
TEACHING ACTIVITIES:
1. Discuss testing of cooling fan, fan clutch, fan shroud,
and air dams
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 29
TASK: Inspect and test electric cooling fan, fan control
system and circuits
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.10 - Inspect and test electric cooling fan, fan control
system and circuits; determine necessary action.
ENABLING OBJECTIVES:
Use of mulitmeter
TEACHING ACTIVITIES:
1. Discuss testing of electric cooling fan, fan control system and circuits
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 30
TASK: Diagnose temperature control problems in the heater/ventilation
system
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.11 – Diagnose temperature control problems in the heater/ventilation system;
determine necessary action.
ENABLING OBJECTIVES:
Use of multimeter
TEACHING ACTIVITIES:
1. Discuss diagnosis of temperature control problems in the
heater/ventilation system
Duty: Diagnose and Repair Heating, Ventilation, and Engine
Cooling System
PERFORMANCE OBJECTIVE 31
TASK: Testing heater control valve(s)
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.3.12 - Inspect and test heater control valve(s); perform
necessary action
ENABLING OBJECTIVES:
Use of multimeter
TEACHING ACTIVITIES:
1. Discuss inspection of heater control valve(s)
Operating Systems and Related
Controls
Diagnosis and Repair
Duty: Operating Systems and Related Controls Diagnosis and
Repair
PERFORMANCE OBJECTIVE 32
TASK: Diagnosis of the electrical controls of heating, ventilation,
and A/C (HVAC) systems
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.4.1 - Diagnose malfunctions in the electrical controls of heating, ventilation,
and A/C (HVAC) systems; determine necessary action
ENABLING OBJECTIVES:
Use of multimeter
TEACHING ACTIVITIES:
1. Demonstrate diagnosis techniques of electrical controls of heating,
ventilation, and A/C (HVAC) systems
Duty: Operating Systems and Related Controls Diagnosis and
Repair
PERFORMANCE OBJECTIVE 33
TASK: Inspect and test A/C-heater blower, motors, resistors, switches,
relays,wiring, and protection devices
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.4.2 - Inspect and test A/C-heater blower, motors, resistors, switches, relays,
wiring, and protection devices; perform necessary action
ENABLING OBJECTIVES:
Use of mulitmeter
TEACHING ACTIVITIES:
1. Discuss inspection and testing of A/C-heater blower, motors, resistors,
switches, relays, wiring, and protection devices
Duty: Operating Systems and Related Controls Diagnosis and
Repair
PERFORMANCE OBJECTIVE 34
TASK:
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.4.3 - Diagnose malfunctions in the vacuum and mechanical components and
controls of the heating, ventilation, and A/C (HVAC) system; determine
necessary action
ENABLING OBJECTIVES:
Use of mulitmeter
TEACHING ACTIVITIES:
1. Discuss operation and diagnosis of vacuum and mechanical
components and controls of the heating, ventilation, and A/C (HVAC)
system
Duty: Operating Systems and Related Controls Diagnosis and
Repair
PERFORMANCE OBJECTIVE 35
TASK: Test A/C compressor load cut-off systems
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.4.4 – Test A/C compressor load cut-off systems to determine necessary action
ENABLING OBJECTIVES:
Use of mulitmeter
TEACHING ACTIVITIES:
1. Discuss testing of A/C compressor load cut-off systems
2. Demonstrate testing of A/C compressor load cut-off systems
Duty: Operating Systems and Related Controls Diagnosis and
Repair
PERFORMANCE OBJECTIVE 36
TASK: Inspect and test A/C-heater control panel assembly
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.4.5 - Inspect and test A/C-heater control panel assembly; determine necessary
action
ENABLING OBJECTIVES:
Use of mulitmeter
TEACHING ACTIVITIES:
1. Discuss operation of A/C-heater control panel assembly
2. Discuss inspection and testing of A/C-heater control panel assembly
Duty: Operating Systems and Related Controls Diagnosis and
Repair
PERFORMANCE OBJECTIVE 37
TASK: Inspect and test A/C-heater control cables and linkages
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.4.6 - Inspect and test A/C-heater control cables and linkages; perform
necessary action.
ENABLING OBJECTIVES:
Use of proper hand tools
TEACHING ACTIVITIES:
1. Discuss operation of A/C-heater control cables and linkages
2. Demonstrate inspection and testing of A/C-heater control cables and
linkages
Duty: Operating Systems and Related Controls Diagnosis and
Repair
PERFORMANCE OBJECTIVE 38
TASK: Inspect A/C-heater ducts, doors, hoses, cabin filters and outlets
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.4.7 - Inspect A/C-heater ducts, doors, hoses, cabin filters and outlets; perform
necessary action
ENABLING OBJECTIVES:
Use of proper hand tools
TEACHING ACTIVITIES:
1. Discuss operation of A/C-heater ducts, doors, hoses, cabin filters and
outlets
2. Discuss inspection and testing of A/C-heater ducts, doors, hoses,
cabin filters and outlets
Duty: Operating Systems and Related Controls Diagnosis and
Repair
PERFORMANCE OBJECTIVE 39
TASK: Check operation of automatic and semi-automatic heating,
ventilation, and air-conditioning (HVAC) control systems
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.4.8 – Check operation of automatic and semi-automatic heating, ventilation,
and air-conditioning (HVAC) control systems; determine necessary action
ENABLING OBJECTIVES:
Understanding operation criteria
TEACHING ACTIVITIES:
1. Discuss operation of automatic and semi-automatic heating,
ventilation, and air-conditioning (HVAC) control systems
2. Discuss testing of automatic and semi-automatic heating, ventilation,
and air-conditioning (HVAC) control systems
Refrigerant Recovery,
Recycling, and Handling
Duty: Refrigerant Recovery, Recycling, and Handling
PERFORMANCE OBJECTIVE 40
TASK: Refrigerant recovery equipment
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.5.1 – Perform correct use and maintenance of refrigerant handling equipment.
ENABLING OBJECTIVES:
Use of Refrigerant recovery equipment
TEACHING ACTIVITIES:
1. Discuss use of Refrigerant recovery equipment
2. Demonstrate use of Refrigerant recovery equipment
3. Demonstrate maintenance of use of Refrigerant recovery equipment
Duty: Refrigerant Recovery, Recycling, and Handling
PERFORMANCE OBJECTIVE 41
TASK: Identifying refrigerant type
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.5.2 – Identify (by label application or use of a refrigerant identifier) and recover
A/C system refrigerant.
ENABLING OBJECTIVES:
Use of a refrigerant identifier
TEACHING ACTIVITIES:
1. Demonstrate use of a refrigerant identifier
Duty: Refrigerant Recovery, Recycling, and Handling
PERFORMANCE OBJECTIVE 42
TASK: Recycle refrigerant
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.5.3 – Recycle refrigerant
ENABLING OBJECTIVES:
Use of refrigerant recovery equipment
TEACHING ACTIVITIES:
1. Demonstrate use of refrigerant recovery equipment
Duty: Refrigerant Recovery, Recycling, and Handling
PERFORMANCE OBJECTIVE 43
TASK: Label and store refrigerant
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.5.4 – Label and store refrigerant
ENABLING OBJECTIVES:
Use of refrigerant recovery equipment
TEACHING ACTIVITIES:
1. Demonstrate how to label and store refrigerant
Duty: Refrigerant Recovery, Recycling, and Handling
PERFORMANCE OBJECTIVE 44
TASK: Test recycled refrigerant for non-condensable gases.
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.5.5 – Test recycled refrigerant for non-condensable gases.
ENABLING OBJECTIVES:
Use of AC refrigerant identifier
TEACHING ACTIVITIES:
1. Demonstrate procedure for testing recycled refrigerant for noncondensable gases
Duty: Refrigerant Recovery, Recycling, and Handling
PERFORMANCE OBJECTIVE 45
TASK: Evacuate and charge A/C system
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.5.6 – Evacuate and charge A/C system
ENABLING OBJECTIVES:
Use of AC charging equipment
TEACHING ACTIVITIES:
1. Discuss Evacuate and charge A/C system
2. Demonstrate Evacuate and charge A/C system
Duty: Refrigerant Recovery, Recycling, and Handling
PERFORMANCE OBJECTIVE 46
TASK: Obtain certification to service and repair A/C systems
STANDARD OF PERFORMANCE OF TASK: ACAP COMPETENCY
7.5.7 –
ENABLING OBJECTIVES:
Practice taking certification test
TEACHING ACTIVITIES:
1. Perpare students for taking certification test