MCMC MTSFB TC G0XX:2020 TECHNICAL CODE FIXED NETWORK FACILITIES IN-BUILDING AND EXTERNAL (BROWNFIELD MULTI DWELLING UNIT) Developed by Registered by Registered date: © Copyright 2020 MCMC MTSFB TC G0XX:2020 MCMC MTSFB TC G0XX:2020 Development of technical codes The Communications and Multimedia Act 1998 (‘the Act’) provides for Technical Standards Forum designated under section 184 of the Act or the Malaysian Communications and Multimedia Commission (‘the Commission’) to prepare a technical code. The technical code prepared pursuant to section 185 of the Act shall consist of, at least, the requirement for network interoperability and the promotion of safety of network facilities. Section 96 of the Act also provides for the Commission to determine a technical code in accordance with section 55 of the Act if the technical code is not developed under an applicable provision of the Act and it is unlikely to be developed by the Technical Standards Forum within a reasonable time. In exercise of the power conferred by section 184 of the Act, the Commission has designated the Malaysian Technical Standards Forum Bhd (MTSFB) as a Technical Standards Forum which is obligated, among others, to prepare the technical code under section 185 of the Act. A technical code prepared in accordance with section 185 shall not be effective until it is registered by the Commission pursuant to section 95 of the Act. For further information on the technical code, please contact: Malaysian Communications and Multimedia Commission (MCMC) MCMC Tower 1 Jalan Impact Cyber 6 63000 Cyberjaya Selangor Darul Ehsan MALAYSIA Tel: +60 3 8688 8000 Fax: +60 3 8688 1000 http://www.mcmc.gov.my OR Malaysian Technical Standards Forum Bhd (MTSFB) Malaysian Communications & Multimedia Commission (MCMC) Off Persiaran Multimedia Jalan Impact Cyber 6 63000 Cyberjaya Selangor Darul Ehsan MALAYSIA Tel: +60 3 8320 0300 Fax: +60 3 8322 0115 http://www.mtsfb.org.my Contents Page Committee representation ....................................................................................................................... iii Foreword ............................................................................................................................................iv 0. Introduction ...................................................................................................................................... 1 1. Scope ............................................................................................................................................ 1 2. Normative references ...................................................................................................................... 1 3. Abbreviation..................................................................................................................................... 2 4. Requirements .................................................................................................................................. 2 4.1 Overview ............................................................................................................................... 2 Segment A: NFP manhole to common access manhole ...................................................... 4 5 6 7 8 4.3 Segment B: Common access manhole to SDF room or TR ................................................. 5 4.4 Segment C: TR ..................................................................................................................... 6 4.5 Segment D: Vertical infrastructure and cabling..................... Error! Bookmark not defined. 4.6 Segment E: Horizontal infrastructure and cabling .............................................................. 17 4.7 Segment F: In-premise cabling ........................................................................................... 23 Specification .................................................................................................................................. 25 5.1 Cable ................................................................................................................................... 25 5.2 Vertical and Horizontal Trunking ......................................................................................... 27 5.3 Duct and microduct ............................................................................................................. 28 5.4 Fiber termination box (FTB) ................................................................................................ 28 5.5 Fiber wall socket (FWS) ...................................................................................................... 29 5.6 Point of entry (POE) ............................................................................................................ 30 Labelling and tagging .................................................................................................................... 31 6.1 Tag material and specification ............................................................................................ 31 6.2 Testing and commissioning................................................................................................. 33 6.3 Certification of the material ................................................................................................. 36 Infrastructure and cabling acceptance procedure ......................................................................... 36 7.1 Acceptance procedure ........................................................................................................ 36 7.2 Documentation during acceptance procedure .................................................................... 36 Safety and precaution ................................................................................................................... 37 8.1 Configuration of safety device ............................................................................................. 37 8.2 Other safety elements ......................................................................................................... 37 Annex A Specification for blown fibre - alternative in-building fibre cabling system ....................... 39 Annex B Sample of core assignment .............................................................................................. 41 i MCMC MTSFB TC G0XX:YYYY Committee representation This technical code was developed by Fixed Network Facilities Sub Working Group which supervised by Network and Broadcast Infrastructure and Facilities Working Group under the Malaysian Technical Standards Forum Bhd (MTSFB) consists of representatives from the following organisations: Celcom Axiata Berhad Digi Telecommunications Sdn Bhd edotco Malaysia Sdn Bhd Malaysia Digital Economy Corporation Sdn Bhd Maxis Broadband Sdn Bhd Measat Broadcast Network System Sdn Bhd Redsun Engineering Sdn Bhd Telekom Malaysia Bhd TIME dotCom Berhad Universiti Teknikal Malaysia Melaka iii MCMC MTSFB TC G0XX:YYYY Foreword This technical code for Fixed Network Facilities - In-building And External (Brownfield Multi Dwelling Unit) (‘this Technical Code’) was developed pursuant to section 185 of the Act 588 by the Malaysian Technical Standards Forum Bhd (MTSFB) via its Fixed Network Facilities Sub Working Group under the Network and Broadcast Infrastructure and Facilities Working Group. This Technical Code shall continue to be valid and effective from the date of its registration until it is replaced or revoked. MCMC MTSFB TC G0XX:YYYY FIXED NETWORK FACILITIES - IN-BUILDING AND EXTERNAL (BROWNFIELD MULTI DWELLING UNIT) 0. Introduction An access network is a type of communications network which connects subscribers to their immediate service provider. Access network should also support Point-To-Point (P2P) technologies such as Ethernet, which bypasses any outside plant splitter. The process of communicating with a network begins with an access attempt, in which one or more users interact with a communications system to enable initiation of user information transfer. An access attempt itself begins with an issuance of an access request by an access originator. This Technical Code is intended as a reference for architects, consulting engineers, owners, property developers and others who are responsible for planning and erecting buildings. This is in line with the objective to meet the requirements of end users for fixed communications services with minimum disruptions to all services offered by the service providers. 1. Scope This Technical Code specifies the requirements for Multi Dwelling Unit (MDU) infrastructure development for existing building. The building is more than 5 stories which equipped with the Subscriber Distribution Frame (SDF) or Telecommunication Room (TR). Fixed network facilities include all infrastructure and cablings required for fixed network services from the TR to the premise unit. 2. Normative references The following normative references are indispensable for the application of this Technical Code. For dated references, only the edition cited applies. For undated references, the latest edition of the normative references (including any amendments) applies. MCMC MTSFB TC G025-1, Basic Civil Works - Part 1: General Requirements MCMC MTSFB TC G025-2, Basic Civil Works - Part 2: Open Trench MCMC MTSFB TC G025-2, Basic Civil Works - Part 3: Horizontal Directional Drilling MCMC MTSFB TC G025-2, Basic Civil Works - Part 4: Microtrench MCMC MTSFB TC G024, Fixed Network Facilities - In-Building and External ITU-T G.652.D (12/2006), Characteristics of a single-mode optical fibre and cable ITU-T G.657.A, Characteristics of a bending-loss insensitive single-mode optical fibre and cable IEC 60529, Degrees of protection provided by enclosures (IP Code) IEC 60825-1, Safety of laser products - Part 1: Equipment classification and requirements ISO 2081, Metallic and other inorganic coatings - Electroplated coatings of zinc with supplementary treatments on iron or steel 1 MCMC MTSFB TC G0XX:YYYY EIA/TIA 568, Commercial Building Telecommunications Cabling Standard ICEA S-104-696, Indoor-Outdoor Optical Fiber Cable 3. Abbreviation For the purposes of this Technical Code, the following abbreviations apply. BM Building Management BTU Broadband Termination Unit FTB Fiber Termination Box FWS Fibre Wall Socket HDD Horizontal Directional Drilling MDU Multi Dwelling Unit NFP Network Facilities Provider OLTS Optical Loss Test Set OSHE Occupational Safety, Health and Environment OTDR Optical Time Domain Reflectometer P2P Point-To-Point POE Point of Entry PSTN Public Switched Telephone Network PVC Polyvinyl Chloride SC/UPC Standard Connector/Ultra Polished Connector SDF Subscriber Distribution Frame TR Telecommunication Room 4. Requirements 4.1 Overview Infrastructure and cabling requirements for existing building is divided into 6 segments as shown in Figure 1. MCMC MTSFB TC G0XX:YYYY Figure 1. Infrastructure and cabling segments Infrastructure and cabling demarcation are separated at property boundary which all infrastructure inside the property boundary is under BM responsibilities. For external portion, it is normally under Network Facilities Provider (NFP). 3 MCMC MTSFB TC G0XX:YYYY Segment A: NFP manhole to common access manhole Segment A is a connection from individual NFP manhole until common access manhole inside the property boundary as shown in Figure 2. Figure 2. NFP manhole to common access manhole Infrastructure involved in this segment are as follows: a) NFP manhole; and b) underground ducting to connect between NFP manhole and common access manhole. 4.2.1 Underground ducting NFP shall laid their own duct from common access manhole until their manhole. The capacity and size of the duct is depending on the availability and configuration of common access manhole. Depending on approval by Building Management (BM) The construction of underground ducting may be constructed using any of the following 3 methods: a) open trench; b) Horizontal Directional Drilling (HDD); or c) micro trenching. Details specification of the 3 methods, are specified in MCMC MTSFB TC G025 (all parts). 4.2.2 Common access manhole Specification of the manhole and number of duct ways are tabulated in Table 1. MCMC MTSFB TC G0XX:YYYY Table 1. Manhole size and location No Type of manhole 1 JB30 Recommended No. of size No. of premise No of (mm) duct way linked duct premise (L x W x D) way 850 x a) 850 x 2 4 <4 b) 650 a) JRC7 1,160 x 855 x 850 3 JC9C 1,960 x 1,260 x 1,020 4 N/A > 576 4 R1A 2,200 x 1,615 x 1,680 6 or 8 N/A < 576 2 2 N/A < 72 b) c) a) b) c) Location or criteria Last connection to premise unit. Premise access manhole. On small roadside to link up with JB30. NFP common access manhole. TR Linked manhole. On heavy roadside to link up with JB30/JRC7. NFP common access manhole. TR Linked manhole. TR Linked manhole. In case of the manhole is full and cannot be tapped with new ducting. The NFP may consider on the following options: a) to builds new manhole; b) direct connect to the intermediate or TR manhole; or c) using underground duct branching method. Both BM and NFP should discuss and explore the best option or method to be used. 4.3 Segment B: Common access manhole to SDF room or TR Segment B is supposedly utilising the existing infrastructure which consist of a manhole and underground duct build during property development as illustrated in Figure 3. The details specification is described in MCMC MTSFB TC G024. Figure 3. Common access manhole to TR infrastructure 5 MCMC MTSFB TC G0XX:YYYY NFP shall laid their cable using the provided infrastructure to connect the building SDF with their network. Necessary approval or/and permit to work shall be obtained before NFP start laying of any cable. NFP shall plan the appropriate cable size and capacity to optimise the infrastructure to cater for existing and future demand. All record of duct usage shall be kept by BM and the cable shall be properly tagged at TR, common access manhole or/and intermediate manhole if any. BM shall allocate and assign the underground duct used by every NFP. BM shall construct additional duct for the case of existing duct are already full. 4.4 Segment C: TR Segment C as illustrated in Figure 4 is focused on the SDF room or TR requirements. Detail specification is described in MCMC MTSFB TC G024. Figure 4. TR space arrangement There are 2 main components inside the TR as follows: a) NFP fiber termination point; and b) In-building termination point. BM shall allocate and assign the acquire space for every NFP. A proper cable trunking system and fibre core assignment shall be provided to connect all the components as show in Figure 5.Error! Reference source not found. MCMC MTSFB TC G0XX:YYYY Figure 5. TR components A complete cabling diagram shall be made available in TR for reference of NFP to provision the services. 4.4.1 Cable trunking system Cable trunking system shall be provided in the TR to manage and protect the fiber optic cable. It shall be installed from the entry point until the exit point of the fiber optic cable which includes the excess to the termination points as shown in Figure 6. Figure 6. Installation of cable ladder in the TR There are 2 types of cable trunking system as follows: a) metal cable ladder; and b) metal cable tray. 7 MCMC MTSFB TC G0XX:YYYY 4.4.2 Specification for metal cable tray Standard cable tray width used in TR is 300 mm as illustrated in Figure 7. The material type is mild steel 6 mm coated. Figure 7. Sample of metal cable tray in TR 4.4.3 Specification for metal cable tray trunking type Standard metal cable tray used in TR is perforated cable tray type as shown in Figure 8. The specifications are tabulated in Table 2. Figure 8. Sample of Perforated Cable Tray Table 2. Metal tray specifications Parameter Specifications Width 200 mm - 300 mm Height 10. mm - 50 mm Thickness 1.5 mm - 2.0 mm Material Mild Steel SS 304 MCMC MTSFB TC G0XX:YYYY 4.4.4 NFP fiber termination point NFP termination point inside TR is referred as NFP’s Fiber Termination Box (FTB). It is normally in a form of wall mounted or standard 19 -inch rack type depends on the capacity of the cable. Wall mounted type is normally suitable for 4 cores up to 128 cores cable. Rack type shall be used for higher capacity of cable, i.e. 96 cores and above. Wall mounted FTB shall be labelling and tagging as shown in Figure 9. Figure 9. Wall mounted type FTB Rack type FTB shall be labelling and tagging as shown in Figure 10 . Figure 10. Rack Type FTB BM shall allocate and advice the proper location of NFP’s FTB. All NFP cable shall be terminated at FTB. 9 MCMC MTSFB TC G0XX:YYYY For FTTH services, NFP may use optical splitter inside their FTB. 4.4.5 In-building cabling termination point In-building cabling is referred to the fiber cabling from TR to individual premise. In-Building termination point inside TR is referred as in-building fiber cabling FTB. A standard 19-inch rack type as shown in Figure 11 is recommended since it require high capacity of cable termination. The FTB and in-building cabling shall be prepared by BM. Capacity of in-building cabling termination point shall cover 100 % termination of the premise. Figure 11. In-building cabling termination point 4.5 Segment D: Vertical infrastructure and cabling Segment D is referred to the requirement of vertical infrastructure and cabling connecting TR until floor FTB as shown in Figure 12. MCMC MTSFB TC G0XX:YYYY Figure 12. Vertical infrastructure 4.5.1 Vertical trunking Existing vertical trunking either open trunking or closed metal trunking shall be used to laid a new cable. 4.5.1.1 Construction of new trunking New closed metal or open trunking shall be constructed if existing trunking is not available or fully occupied. Wall plug with screws shall be used to installed the trunking in the vertical riser. 4.5.1.2 Floor hacking An adequate floor hacking shall be executed in case there are no space at floor rise to pull the cable fibre using proper tools. The hacking hole is depending on trunking size that planned to be installed and shall not exceed 300 mm x 70 mm size at one time. Any hacking activities shall obtain approval from BM. All hacking works shall be made good with a proper filling material. There is no gap shall be leaved upon completion of installation work. Sample of good hacking condition is shown in Figure 13. 11 MCMC MTSFB TC G0XX:YYYY Figure 13. Proper floor hacking condition An approval from BM shall be obtained before any floor hacking work start. Hacking method and affected size must be clearly explained during applying the approval. 4.5.2 Vertical cabling 4.5.2.1 Vertical cable planning There are 3 main components of vertical cabling as follows: a) main FTB as in-building termination point; b) vertical cable; and c) floor FTB. 4.5.2.1.1 Pre-installed design Sample of pre-installed cabling design is shown in Figure 14. Vertical cable shall be able to cover 100 % terminations of the premises for pre-installed design. MCMC MTSFB TC G0XX:YYYY Figure 14. Pre-installed cabling design The cabling requirement for every premises should be as follows: a) minimum of 2 cores for residential type; and b) minimum of 4 cores for business type. Property develop should consult the NFP for the appropriate number of cores based on the actual requirement. 4.5.2.1.2 As we grow design The capacity of main FTB, vertical cable and floor FTB is depends on the forecasted demand in particular building for as we grow design. Normally this design is applied for the case of NFP to provide the cable. Additional capacity is required to be added later once existing capacity is not enough to cater for new demand. There are 2 designs can be adopted which are: a) direct cabling; and b) using splitter. Direct cabling is a one-to-one cabling from main FTB until floor FTB which the vertical cabling insertion loss is consistence and will not depends on overall NFP network planning. Figure 15 shows the sample design of as we grow design with direct cabling design. 13 MCMC MTSFB TC G0XX:YYYY Figure 15. Sample of as we grow direct cabling design Using splitter design consist of splitter in the cabling design and will highly depend on overall NFP network planning and design. The design is non-standard and shall be discussed and approved by NFP case by case basis. Sample design of as we grow using splitter design is shown in Figure 16 which indicates 50 % demand and 1:8 splitter at floor FTB. Figure 16. Sample of as we grow using splitter design MCMC MTSFB TC G0XX:YYYY 4.5.2.2 Cable installation During the installation of vertical cable, the cable shall be tied properly with cable tie to the trunking. A proper length of cable shall be used to avoid any intermediate joint. A tap out technic shall be used to minimise the insertion loss at every joint. Only related fiber core shall be cut while the other cable cores shall be remained in the cable. 4.5.2.2.1 Cable installation via open trunking Sample of vertical open trunking is shown in Figure 17. For normal conventional cable indoor or outdoor cable with pulling strength > 1,000 Nm, the cable shall be pull using corrugated duct or can be directly installed without any protection conduit. For other cable with lower tensile strength such as microcable or drop cable, the cable shall be installed using a proper microduct to provide a protection to the cable. Figure 17. Sample of vertical open trunking A proper tagging as shown in Figure 18 shall be used at every floor for easier identification. The tag shall be placed direct to the cable or protection duct. Figure 18. Cable tagging 15 MCMC MTSFB TC G0XX:YYYY 4.5.2.2.2 Cable installation via closed metal trunking All cables shall be laid without any conduit or duct inside the closed metal trunking to optimise the size. During installation of cable, metal trunking cap shall carefully open before installing the cable and installed back upon the completion of cable installation work. A proper tool shall be used to open the trunking cap. Force open is strictly prohibited to avoid damage of the trunking. 4.5.3 Inter-building connection Inter-building connection is connecting 2 or more building to a single TR that have connecting to NFP network. In-building cabling shall be laid via underground ducting same as explained in 4.3. The capacity of the cabling shall follow the same requirements as in 4.5.2. Figure 19 shows the sample of inter-building connection. Figure 19. Inter-building connection MCMC MTSFB TC G0XX:YYYY 4.6 Segment E: Horizontal infrastructure and cabling Segment E as shown in Figure 20 is referred to the requirement of horizontal infrastructure and cabling connecting the floor FTB and individual premise. Figure 20. Horizontal infrastructure Horizontal infrastructure and cabling are depending on building type, responsibility and capacity of the building with the option as explained below. Pre-Installed cabling Pre-installed horizontal infrastructure and cabling as in Figure 21 is recommended for high demand building and to be provided by the BM. Figure 21. Horizontal trunking with pre-installed cabling 17 MCMC MTSFB TC G0XX:YYYY 4.6.1.1 Horizontal cable Horizontal cabling refers to the floor distribution cabling between floor FTB to every individual premises Fiber Wall Socket (FWS) with the following capacity: a) Residential type - a minimum of 2 cores for each premises for residential type; and b) Business type - a minimum of 4 cores for each premises. 10 % extra cores are recommended to be prepared. BM is recommended to consult with NFP for the appropriate capacity planning. Horizontal cable shall be pre-terminated at individual premises FWS using Standard Connector/Ultra Polished Connector (SC/UPC) connector. At the floor FTB side, it is depending on vertical cabling design according to the following scenarios: a) pre-connect with vertical cabling core for the case vertical cabling was designed with pre-installed. The connection can be direct splicing or using SC/UPC connector based on vertical cabling design; or b) terminate at empty adaptor or properly left hanging inside the Floor FTB with SC/UPC connector for the case of vertical cabling was not designed with full premise capacity. Every cabling shall be tagged and labelling properly with premise unit number. 4.6.1.2 Horizontal trunking The cable for horizontal fibre cabling should be secured through the following methods: a) exposed wall or surface ducting or trunking; b) concealed ducting inside the wall; c) concealed ducting under the floor; or d) conduit ducting through the ceiling. The size of the trunking and ducting depends on the capacity and size of the cable. The trunking or ducting of horizontal cabling shall be made from Polyvinyl Chloride (PVC) or higher material. The specification of trunking sizes are as in Table 3. Table 3. Trunking size Type Conduit Closed trunking 4.6.2 Unit per floor Specifications 8 and below Minimum of 50 mm diameter More than 8 Minimum of 100 mm diameter 8 and below Minimum of 50 mm (W) x 50 mm (H) More than 8 Minimum of 100 mm (W) x 50 mm (H) Horizontal trunking with cabling up to Point of Entry (POE) only Pre-Installed horizontal trunking with cabling up to Point of Entry (POE) only as shown in Figure 22 is recommended for high demand building and to be provided by the BM. The in-premise cabling will be installed as and when customer subscribe the service from NFP. MCMC MTSFB TC G0XX:YYYY Figure 22. Horizontal trunking with cabling up to POE design Pre-installed trunking will only cover common area portion without needs to enter individual premises. POE shall be prepared at in front of every premise for horizontal cable to exit and ready to enter the individual premise later. 4.6.2.1 Horizontal cable Horizontal cable refers to the floor distribution cabling between floor FTB to every individual premises POE with the same capacity as explained in 4.6.4.1. Horizontal cable shall be pre-terminated at individual premises POE using SC/UPC connector or leave as bare fiber. At the floor FTB side, the requirement is the same as explained in 4.6.4.1. Bend insensitive drop cable or indoor cable type is highly recommend for easy identification, installation, handing and maintenance. 4.6.2.2 Horizontal trunking The requirement is same as explained in 4.6.3.1. 4.6.2.3 Point of entry (POE) with fiber POE with fiber is referring to entrance point to individual premises with fiber terminated inside. Figure 23 shows the sample of POE. Figures 24 and 25 illustrate the POE for bare fiber and SC/UPC connector. Figure 23. POE 19 MCMC MTSFB TC G0XX:YYYY Figure 24. POE for bare fiber Figure 25. POE for SC/UPC connector POE shall be installed and meet the requirements as follows: a) located indoor and same level of horizontal trunking or lower with maximum height of 3 m; b) practically and technically accessible for installation of cable into the premise later; c) not disturbing the resident or public; d) save and protected environment; and e) suitable material and specification for indoor used. It is highly recommended to get the agreement from premise owner on the suitability of POE location prior the installation. 4.6.3 Pre-installed trunking only Pre-Installed horizontal trunking only as shown in Figures 26 and 27 are recommended for low demand building and to be provided by the BM. The cabling will be installed as and when customer subscribe the service by NFP or BM depending on the commercial agreement between both parties. MCMC MTSFB TC G0XX:YYYY Figure 26. Horizontal trunking only design with closed trunking type Figure 27. Horizontal trunking only design with conduit type Preinstalled trunking will only cover on common area portion without entering individual premises. A POE shall be prepared at in front of every premise for horizontal cable to exit and enter the individual premise later. 4.6.3.1 Horizontal trunking The requirement is the same as explained in 4.6.2.1. A draw rope shall be prepared with a proper premise unit number tagging at FTB side for the case of conduit type is used. The other end of draw rope shall be stored properly at POE of related premises. For the case of close trunking type, the following requirements shall be met: a) trunking shall be installed at maximum of 3 m height; b) below the ceiling level; and c) easy access according to standard Occupational Safety, Health and Environment (OSHE) requirement. 4.6.3.2 Point of entry (POE) 21 MCMC MTSFB TC G0XX:YYYY POE for pre-installed trunking only design is referring to entrance point to individual premises without fiber terminated inside. The requirement is the same as in 4.6.2.3 except for the fiber is not required and it shall be replaced with draw rope if conduit type is used or leave empty for closed trunking type. The smaller size of POE may be used since it will only be used to pull the fiber without any termination or connector inside. 4.6.4 As and when installation As and when horizontal cabling installation is recommended for low demand building and the cabling is normally provided by NFP as and when customer subscribe the service. The installation method shall be agreed between NFP and BM before NFP is allowed to install their network at the building. 4.6.4.1 Cable installation using existing trunking Horizontal cabling can be installed using existing trunking for the case the trunking was pre-installed by properties developer or BM is available. The trunking can be open trunking or conduit type as explained in 4.6.3.1. The installation method is depending on trunking type. Draw rope as shown in Figure 28 shall be used for installation through conduit type. Rodding process shall be performed in case the draw rope is not available or broken. Figure 28. Pulling cable through conduit type Direct installation inside the trunking shall be used for the case open trunking type as in Figure 29 is used without using any protection duct to save the space. Figure 29. Pulling cable through open trunking type 4.6.4.2 Cable installation without trunking Horizontal cable also can be installed without trunking. However, the installation method is highly depending on the agreement from BM. Below are some of the method that can be used: a) clip on the wall (see Figure 30) MCMC MTSFB TC G0XX:YYYY This method is suitable for the case of drop cable or small indoor cable is used. Wall clip or suitable adhesive tape can be used to fixed the cable on the wall surface. The colour of the cable is recommended to follow the wall colour to provide the aesthetic value and transparent view. The height of the cable shall follow OSHE requirement. Figure 30. Wall clip cable installation b) clip on wall with microduct (see Figure 31) This method is suitable for the case of horizontal cable require protection or expose to outdoor environment where the cable may be installed using microduct. Figure 31. Wall clip with microduct c) Over the ceiling Installation of horizontal cable over the ceiling is also allowed for the case the ceiling is not too high and meet the OSHE requirement. A proper ceiling entrance and exit hole shall be made available for this method of installation. The cable shall be protected using a microduct. The microduct shall be installed first and the cable to be installed later using draw rope inside the microduct to avoid damage of the cable. 4.7 Segment F: In-premise cabling In-premise cabling as shown in Figure 32 is referring to the cabling from POE until Broadband Termination Unit (BTU). 23 MCMC MTSFB TC G0XX:YYYY Figure 32. In-premise cabling For as and when installation design, the in-premise cabling may inclusive in horizontal cabling as explained in 4.6.4. For pre-installed design, detail specification is describes in MCMC MTSFB TC G024. Indoor type drop cable is recommended to be used for in-premise cabling. SC/UPC connector type shall be used for the case of FWS is used before connection to BTU as shown in Figure 33. Figure 33. In-premise with FWS connection Method of installation is highly depending on customer preference and commercial offer by NFP during service subscription. In-premise cabling for business building shall be installed and terminated inside the server, equipment or PABX room which installed with all telecommunication related device as shown in Figure 34. Figure 34. In-premise cabling for business premises MCMC MTSFB TC G0XX:YYYY 5 Specification 5.1 Cable 5.1.1 Indoor cable for vertical cabling Cable specification for campus backbone cable and vertical cable is usually the same. However, for campus backbone, it is usually erected through underground. Therefore, the underground type of cable shall be used. The types of cable that can be used for vertical cabling are: a) normal conventional FOC or generally known as round cable; b) indoor tight buffer cable; c) loose tube cable; or d) blown fibre (detailed specifications are provided in Annex A). All cables shall be single mode type and comply with the specifications of ITU-T G.652.D or ITU-T G.657.A. Sample of campus backbone and vertical cable is shown in Figure 3535 and 36. Figure 35. Possible vertical fibre cable design - Loose tube Figure 36. Possible vertical fibre cable design - Ribbon Underground cables are designed for high pulling tension and lubricants are used to reduce friction on longer pulls. Automated pulling equipment that limits pulling tension shall able to protects the cables. For very long runs or those with more bends in the conduit may require intermediate pulls through the manhole or any suitable pit. 25 MCMC MTSFB TC G0XX:YYYY 5.1.2 Indoor drop cable for horizontal and in-premise cabling Indoor drop cable for horizontal and in-premise cabling shall be single-mode in-building fibre reinforced with FRP for indoor applications. The fibre characteristic are as follows: a) the fibre characteristic shall be in accordance with the ITU-T G.657A (bend insensitive fibre ≤ 15 mm bending radius). b) macro bending loss performance at 1,550 nm and 1,625 nm regions shall be in accordance with Class A of Clause 7 of ITU-T G.657 (12/2006). c) In order to ensure low loss operation at 1,550 nm and 1,625 nm regions, the increase in loss for 10 turns of the loosely wound fibre using a mandrel with 15 mm radius should be 0.5 dB. d) Maximum loss at 1,550 nm shall be 0.25 dB and at 1,625 nm shall be 1.0 dB Proof stress shall not be less than 0.69 Gpa. Chromatic dispersion coefficient shall be as follow: a) Zero dispersion slope shall be less than and equal to 0.092 ps/nm2km. b) Zero dispersion wavelength shall range from 1300 nm to 1324 nm The attenuation coefficient of the Fibre shall be as follows: a) Maximum 0.35 dB/km, from 1,310 nm to 1,625 nm regions. b) Maximum 0.4 dB/km in the 1,383 nm ±3 nm region. c) Maximum 0.3 dB/km in the 1,550 nm region. PMD Coefficient - PMD link design value shall be maximum of 0.2 ps/√km in accordance with Class A of Clause 7 of ITU-T G.657 (12/2006). Optical fibre shall be placed in between two strength members. The construction of cable shall be 1 fibre or 2 fibre cores. The colour coding shall be as Table 4. Table 4. In-building fibre cable colour coding Number Fibre 1 Blue 2 Yellow The cable shall contain FRP material as cable strength member. Nominal diameter for FRP shall be 0.4 mm. The in-building drop fibres nominal outer diameter shall be 3.1 mm x 2.0 mm. The in-building drop fibres shall be sheathed with polyethylene and flame-retardant characteristic. Performance on oxygen index of sheath shall be ≥ 27. MCMC MTSFB TC G0XX:YYYY 5.1.2.1 The sheath The sheath shall be ivory colour and shall not promote the growth of fungus. The sheath around the cable and bearer wire shall be free from pinholes, joints, mended places and other defects and able to provide adequate mechanical protection against impact and crushing. The sheath shall be marked with the manufacturer’s name, sequential meter, month and year of manufacturer, fibre count and fibre type. The marking shall be in contrasting colour to the cable sheath. The preferred marking colour will be white. The general cable performance test of the offered shall be in accordance with ICEA S-104-696 or equivalent to other international standards. It shall be verified through suitable test. The tensile strength shall be in excess of 80 N. At this load, no residual fibre elongation and the increase in attenuation shall be less than 0.05 dB/km. 5.1.2.2 Bend test The cable shall be unwound and ten (10) turns shall be wrapped in a close helix around a mandrel of radius 15 mm. The turns shall be applied at a uniform rate of one revolution in about 5 seconds and with sufficient tension to ensure that the specimen contours the mandrel. The turns shall be then unwound and the cycle repeated 3 times. Finally, measurement shall show no change to the optical characteristics of the cable. 5.1.3 Microcable Detail specification are explained in MCMC MTSFB TC G025-3. 5.2 Vertical and Horizontal Trunking Type of trunking as shown in Figure 37 shall be either open trunking or closed metal trunking. Figure 37. Trunking Type The thickness of the trunking is 2 mm. Minimum size of the trunking is as follows: a) closed metal trunking: 100 mm x 50 mm; and b) open metal trunking: 200 mm x 50 mm. 27 MCMC MTSFB TC G0XX:YYYY The material shall be a mild steel type or higher grade shall be used for both closed or open metal trunking. Recommended colour is green for metal type trunking or can used white colour PVC as an alternative. 5.3 Duct and microduct Duct and microduct specification shall follow requirements described in MCMC MTSFB TC G025-1. The duct and micro ducts shall be numbered accordingly with the nominal outer diameter shall be 5 mm. It shall be constructed with polyethylene and flame-retardant characteristic. Performance on oxygen index of sheath shall be ≥ 27. The colour shall be ivory colour and shall not promote the growth of fungus. The duct and micro duct around the cable shall be free from pinholes, joints, mended places and other defects and able to provide adequate mechanical protection against impact and crushing. The tensile strength of the micro duct shall be in excess of 70 N. The marking shall be in contrasting colour to the micro duct. The preferred marking colour will be white. 5.4 Fiber termination box (FTB) The FTB shall be suitable for attachment to inside or outside wall of a building. The material shall be able to protect the component against harsh, high heat and humidity environment. The FTB shall be designed and conforms to IP44 of IEC 60529 or better for indoor application and IP54 of IEC 60529 or better for outdoor application. Evidence (such as certificate, letter of conformance, etc.) from MCMC’s registered certifying agency or authorized body shall be provided during approval process. The FTB shall be suitable for 19-inch rack-mount and/or wall mounted. The offered FTB shall complete with its respective mounting kits. The framework of the high density and medium density FTB shall be fabricated from the following materials: a) electro-galvanised steel; b) rust proof steel plating; c) plastic injection moulded; or d) thermoplastic. of thickness not less than 2.0 mm and the design shall conform to ISO 2081 or other recognised standards. All FTH shall be made of fire-retardant material. All the plastic material shall have a rating of V-1 or better as determined by Underwriters Laboratories’ UL94 standards. The FTB shall be designed with built-in splitter or without splitter. All FTB edges shall be rounded. Total weight of the FTB including full accessories shall be suitable for wall mounting. MCMC MTSFB TC G0XX:YYYY For high density FTB, the maximum overall dimension shall be 406 mm (H) x 457 mm (W) x 152 mm (D). For customer premises FTB, the maximum overall dimension shall be 203 mm (H) x 127 mm (W) x 38 mm (D). Detailed specification, characteristic and technical drawing of the various sizes of the FTB offered shall be furnished during the submission of proposal for evaluation. The FTB shall consist of moulded inner fibre slack storage, sleeve holder and integral positive lock strain relief for cable and other accessories deem necessary. The FTB design shall have suitable splice tray and cable management area to provide for minimum bending radius and for storage ruggedized splitter pigtails. Suitable number of splices organized trays or splice trays shall be provided in the splice compartment. The splice tray shall be of cartridge or cassette types that are stackable and flappable or able to be opened sideways. The number of trays and other appropriate accessories provided shall suit the maximum number of cores of the fibres intended to be installed. The splice tray shall comply with GR-771. The FTB shall have pre-assembled plates with SC/UPC type of adaptor coupling for fibre patching. It shall be designed with 2 physically separated compartments to isolate the incoming cable (capable of accommodating splitter where needed) from the drop fibre compartment. The door opening shall be designed for suitable operation in confined space. The FTB shall be provided with various sizes of cable entries at both top and bottom. All cable entries shall be provided with rubber grommets to protect the cable and prevent pest and dirt entry. The rubber grommets shall have suitable guides for different cable sizes to permits pass through of additional fibres. The FTB design shall be economical, effective, robust and compact to provide access point for drop fibre and internal fibre. Each FTB shall be provided with a table or label card for circuit identification purpose. The table shall be printed on durable material in such a manner as to be permanently legible, protected by an acrylic pocket and properly displayed on the inside cover of the FTB. The laser caution signs shall comply with IEC 60825-1. 5.5 Fiber Wall Socket (FWS) The FWS shall be suitable for attachment to inside or outside wall of a building. The material shall be able to protect the component against harsh, high heat and humidity environment. The FWS shall be designed and conforms to IP44 of IEC 60529 Ed. 2.1 or better for indoor application and IP54 of IEC 60529. Evidence (such as certificate, letter of conformance, etc.) from MCMC’s registered certifying agency or authorised body shall be provided during approval process. 29 MCMC MTSFB TC G0XX:YYYY The framework of the high density and medium density FWS shall be fabricated from plastic injection moulded or thermoplastic of thickness not less than 2.0 mm and the design shall conform to ISO 2081 or other recognised standards. All FWS shall be made of fire-retardant material. All the plastic material shall have a rating of V-1 or better as determined by Underwriters Laboratories’ UL94 standards. All FWS edges shall be rounded and suitable to be installed inside the premise’s environment. Total weight of the FWS including full accessories shall be suitable for wall mounting. For customer premises FWS, the maximum overall dimension shall be 203 mm (H) x 127 mm (W) x 38 mm (D). Detailed specification, characteristic and technical drawing of the various sizes of the FWS offered shall be furnished during the submission of proposal for evaluation. The FWS shall consist of moulded inner fibre slack storage, sleeve holder and integral positive lock strain relief for cable and other accessories deem necessary. The FWS design shall have suitable splice tray and cable management area to provide for minimum bending radius and for storage ruggedized splitter pigtails. Suitable number of splices organized trays or splice trays shall be provided in the splice compartment. The splice tray shall be of cartridge or cassette types that are stackable and flappable or able to be opened sideways. The number of trays and other appropriate accessories provided shall suit the maximum number of cores of the fibres intended to be installed. The splice tray shall comply with GR-771. The FWS shall have pre-assembled plates with SC/UPC type of adaptor coupling for fibre patching. It shall be designed with 2 physically separated compartments to isolate the incoming cable and outgoing cable. The door opening shall be designed for suitable operation in confined space. The FWS shall be provided with various sizes of cable entries at both top and bottom. All cable entries shall be provided with rubber grommets to protect the cable and prevent pest and dirt entry. The rubber grommets shall have suitable guides for different cable sizes to permits pass through of additional fibres. The FWS design shall be economical, effective, robust and compact to provide access point for drop fibre and internal fibre. Each FWS shall be provided with a table or label card for circuit identification purpose. The table shall be printed on durable material in such a manner as to be permanently legible, protected by an acrylic pocket and properly displayed on the inside cover of the FWS. The laser caution signs shall comply with IEC 60825-1. 5.6 Point of entry (POE) The POE shall be suitable for attachment to inside or outside wall of a building. The material shall be able to protect the component against harsh, high heat and humidity environment. The POE shall be designed and conforms to IP44 of IEC 60529 or better for indoor application and IP54 of IEC 60529. MCMC MTSFB TC G0XX:YYYY Evidence (such as certificate, letter of conformance, etc.) from MCMC’s registered certifying agency or authorized body shall be provided during approval process. The framework of the high density and medium density POE shall be fabricated from plastic injection moulded or thermoplastic of thickness not less than 2.0 mm and the design shall conform to ISO 2081 or other recognised standards. All POE shall be made of fire-retardant material. All the plastic material shall have a rating of V-1 or better as determined by Underwriters Laboratories’ UL94 standards. Total weight of the POE including full accessories shall be suitable for wall mounting. The maximum overall dimension shall be 203 mm (H) x 127 mm (W) x 38 mm (D). Detailed specification, characteristic and technical drawing of the various sizes of the POE offered shall be furnished during the submission of proposal for evaluation. The POE shall consist of moulded inner fibre slack storage, sleeve holder and integral positive lock strain relief for cable and other accessories deem necessary. The POE design shall have suitable splice tray and cable management area to provide for minimum bending radius and for storage ruggedized splitter pigtails. Suitable number of splices organised trays or splice trays shall be provided in the splice compartment. The splice tray shall be of cartridge or cassette types that are stackable and flappable or able to be opened sideways. The number of trays and other appropriate accessories provided shall suit the maximum number of cores of the fibres intended to be installed. The splice tray shall comply with GR-771. The POE shall have pre-assembled plates with SC/UPC type of adaptor coupling for fibre patching if require. It shall be designed with 2 physically separated compartments to isolate the incoming cable and outgoing cable. The POE shall be provided with various sizes of cable entries at both top and bottom. All cable entries shall be provided with rubber grommets to protect the cable and prevent pest and dirt entry. The rubber grommets shall have suitable guides for different cable sizes to permits pass through of additional fibres. The POE design shall be economical, effective, robust and compact to provide access point for drop fibre and internal fibre. Each POE shall be provided with a table or label card for circuit identification purpose. The table shall be printed on durable material in such a manner as to be permanently legible, protected by an acrylic pocket and properly displayed on the inside cover of the POE. Approved laser caution signs as per IEC 60825-1 requirements shall be provided as standard for every POE. 6 6.1 Labelling and tagging Tag material and specification Cable tag is used to identify the cable information such as core number, origin and destination of the cable. All fibre cables shall be tagged properly at every termination point and cable end. All tags shall be stated clearly and sealed with transparent material for easy to read. Sample of recommended tagging method is as shown in Figure 38. 31 MCMC MTSFB TC G0XX:YYYY Figure 38. Sample of recommended tagging system Cable tag shall use clear and strong material such as plastic, nylon, vinyl or PE. The tag shall comply with UL 94 V Fire Retardant. All information on tag shall be machine printed and can easily be read. The printed material shall sustain, not paled or faded for a minimum 10-year. Usage of paper or market pen is strictly not allowed. Suitable tag size shall be used according to cable, pigtail or fibre core size. The generic recommended size is 1 cm x 2 cm flag type as shown in Figure 39. Figure 39. Cable tag Tag colour shall be white background with black font. Sample of vertical cable tag is shown in Figure 4040. Figure 40. Vertical cable tag 6.1.1 Labelling and tagging of cable All cablings shall have a code or naming convention and shall be tagged properly for smooth service activation and restoration process. All cable information also needs to be inventoried and a copy of inventory information shall be submitted to the NFP during cabling approval or service activation process. All information of the cabling inventory shall be placed and indicated clearly inside TR or FTB for easier reference. BM shall record and update the information whenever there are any changes. Code or naming convention for vertical and horizontal cabling shall follow as shown in Table 5. The table shall be placed inside the TR’s FTB. MCMC MTSFB TC G0XX:YYYY Table 5. Code for internal vertical and horizontal cable Vertical cable Riser info Horizontal cable Item Cable number Core number Floor Cable number Core number Code FV xxx xxx FLxxx FHxxx xxx Example FV001 - FV999 000 - 999 FL020 FH001 – FH999 000 - 999 Vertical cable with FHxxx code shall be tagged at: a) entrance of FWS inside TR; b) entrance to the duct or riser inside TR; and c) each floor riser. Horizontal cable with FVxxx code shall be tagged at inside floor FTB (if any). 6.2 Testing and commissioning All fibre cores shall be tested upon the completion of end-to-end cabling system. Minimum test parameter is total insertion loss of every fibre core. Other parameters such as optical return loss, component insertion loss, splice loss and distance may also be considered to ensure the cabling is at the best condition. Total attenuation loss shall be measured using Optical Time Domain Reflectometer (OTDR), Optical Loss Test Set (OLTS) or Set of Light Source and Power Meter. All test equipment shall be configured with wavelength of 1,310 nm. Testing should comprise of a bi-directional end-to-end OTDR trace performed according to TIA/EIA 455-61 or ISO/IEC 11801 or a bi-directional end-to-end power meter test performed according to TIA/EIA 455-53A or ISO /IEC 11801. Each link that does not conform to the standard requirement shall be brought into compliance. Total attenuation loss shall follow as show in Table 6. All measurements shall be performed using 1,310 nm wavelength. Table 6. Test location and maximum allowable loss 6.2.1 Portion Maximum loss Cable termination point in TR - Floor FTB 1.8 dB Cable termination point in TR - POE 2.0 dB Cable termination point in TR - FWS 2.3 dB Optical Loss Test Set (OLTS) test method OLTS is a tool to measure point to point attenuation loss in a single cabling. OLTS is able to perform the bi-directional insertion loss measurement with multiple wavelengths together with other parameters such as optical return loss and distance. OLTS shall be used in pair and required to be placed at both ends. Details of the test procedure using OLTS is explained in TIA-568B or TIA/TSB 140. The test setup is as shown in Figure 40. 33 MCMC MTSFB TC G0XX:YYYY Figure 40. OLTS testing method Before performing any test, both OLTS require a reference using the test patch cord to reset the connection. A high quality of test patch cord shall be used to get the accurate measurement. 6.2.2 Optical Time Domain Reflectometer (OTDR) test method OTDR is a single ended measurement which is able to provide a total insertion loss, every event loss, distance, bi-directional result and ORL through a single measurement. Below are the items that should be consider by using the OTRD measurement: a) To obtain the accurate measurement, open end side shall be closed properly to avoid entering of the light that may contribute to the false light reflection to the test environment. b) To measure the first connector that connected to the test patch cord, a minimum of 10 m spool fibre shall be used between OTDR and the test adaptor. However, to get a better result the longer spool fibre, i.e. 100 m length is recommended to be used. c) At the open-end side, another minimum of 10 m length of spool fibre also needs to be used to obtain the accurate measurement of the last connector. d) A high quality of test patch cord shall be used to get the accurate measurement. OTDR can provide each event measurement in the tested network and should be used during troubleshooting process. The sample test setup for OTDR measurement is as shown in Figure 41. Figure 41. OTDR testing method 6.2.3 Power meter and light source test method Power meter and light source is a single ended insertion loss measurement method and is able to provide the total insertion loss only. To obtain the bi-directional result, both test equipment needs to be swapped and re-performed the test. The test setup shall follow as shown in Figure 42. MCMC MTSFB TC G0XX:YYYY Figure 42. Power meter and light source testing method Before performing any test, reference process using test patch cord is needed to reset the connection between power meter and light source. A high quality of test patch cord shall be used to get the accurate measurement. 6.2.4 Test result Test result shall be provided to NFP during acceptance procedure. All results presented to NFP shall meet all the minimum requirements. Test results are recommended to be printed in test equipment original version with the information of total bi-directional insertion Loss at 1,310 wavelength. The sample of recommended test results format is as shown in Table 6 below. Table 6. Sample of recommended test results format Building name Seri Pinang Condominium Vertical cable no. FV001 FWS rack no. Rack 1 FWS sub-rack no. Sub-rack 1 Test item Test direction Rise FWS adaptor no. Optical return loss optional Insertion loss Downstream Upstream Downstream Upstream Premise unit no. Floor 1,310 nm 1,310 nm 1,310 nm (dB) 1,310 nm (dB) no. (dB) (dB) No. 1 A-1-01 1 1.1 1.1 No. 2 A-1-02 1 1.1 1.1 34 34 110 No. 3 A-1-03 1 1 1 36 36 120 No. 4 A-1-04 1 0.9 0.9 34 34 130 No. 5 A-2-01 2 1.1 1.1 34 34 100 No. 6 A-2-02 2 1.1 1.1 35 35 110 No. 7 A-2-03 2 1 1 34 34 120 No. 8 A-2-04 2 0.9 0.9 34 34 130 Remarks Tester Verified by NFP representative name 35 33 33 Distance (m) 100 MCMC MTSFB TC G0XX:YYYY NFP shall perform a random sampling test to ensure the test results submitted by property developer are correctly captured. The sampling tests shall be done by the property developer during the acceptance procedure with the witness of NFP’s representative. 6.2.5 Test equipment calibration All the test equipment and related tool shall be calibrated according to manufacturer specification and the calibration record shall be presented during acceptance procedure. It is to ensure all test equipment and tools are in the best condition to be used for any measurement. 6.3 Certification of the material All materials used by property developer related to any material specified in this document shall be certified by MCMC’s registered certifying agency or NFP according to the specified standards. The type approval certificates shall be presented during acceptance procedure. For any development that fails to present the certification, it shall be rejected by NFP during acceptance procedure. Certification validity shall be as specified in the certificate. 7 Infrastructure and cabling acceptance procedure 7.1 Acceptance procedure The cabling acceptance shall only be performed for the case cabling was prepared by non NFP only. The acceptance only recommended to be done by first NFP only. The subsequence NFP may request for sampling acceptance and documentation if require. 7.2 Documentation during acceptance procedure During the acceptance, the validation shall be performed on the following items: a) sampling power level check at Floor FTB, POE or FWS based on cabling design; b) Straight Line Drawing (SLD) and as build diagram; c) cabling capacity and design is meeting the specification; d) physical work - fiber bending, routing, labelling, tagging etc; and e) material type approve certificate by registered certifying agency or NFP’s. In case the specification does not meet, the related cabling or infrastructure need to be rectified accordingly. During the validation process, if necessary, NFP will issue Certificate of Acceptance if all of the requirements are fulfilled according to the specifications. The cabling ownership shall be under the BM or NFP who provide the cabling or based on agreement that clearly state on the ownership and responsibility. Documentation during acceptance procedure shall only applicable for the case cabling was prepared by non NFP only. The documentation only recommended to be validated by first NFP only. However, the subsequence NFP may request if require. The lists of required documents are as follows: a) acceptance checklist endorsed by consultant or contractor; MCMC MTSFB TC G0XX:YYYY b) internal infrastructure floor plan; c) external infrastructure development plan; d) as built and cabling schematic line diagram; e) fibre core assignment - sample as shown in Annex B; f) cabling test results; g) calibration certificate of test equipment; and h) registered certifying agency or NFP’s type approval certificate of each material used. During the acceptance process, if necessary, NFP will issue Certificate of Acceptance if all of the requirements are fulfilled according to the specifications. 8 8.1 Safety and precaution Configuration of safety device Safety facilities for construction projects shall adhere to the NFP’s guidelines issued by the relevant parties of NFP and/or any requirements issued by the relevant authorities. The use of safety equipment is required during the installation and handling of optical fibre cable, for example gloves and safety glasses. 8.2 Other safety elements Construction environment, safety requirements and safety condition are as follows: a) firefighting apparatus and material shall be prepared at the job location (i.e. smoke induction, temperature induction and other alarm device) and shall be in good working condition; b) power supply sockets for different voltages in the machine room should have clear identification; c) hazardous goods such as inflammables and explosives and pigtails are forbidden in machine room; d) reserved holes in the building plate should be configured with safety cover; and e) additional safety device should be added to the project to ensure the safety of construction. 37 MCMC MTSFB TC G024:2020 Annex A (normative) Specification for blown fibre - alternative in-building fibre cabling system a) In-building fibre cable shall be single-mode in-building fibre using blown fibre distribution system for in-building applications. b) Fibre characteristic shall be in accordance with ITU-T G.657A (bend insensitive fibre ≤ 15 mm bending radius). c) Macro Bending Loss shall comply to below: i) The loss performance at 1,550 nm and 1,625 nm regions shall be in accordance with ITU-T G.657 class A (12/2006) Clause 7. ii) In order to ensure low loss operation at 1,550 nm and 1,625 nm regions, the increase in loss for 10 turns of the loosely wound fibre using a mandrel with 15mm radius should be 0.5 dB. iii) Maximum loss at 1,550 nm shall be 0.25 dB and at 1625 nm shall be 1.0 dB. d) Proof stress shall not be less than 0.69 Gpa. e) Chromatic dispersion coefficient shall be as follow: f) i) Zero Dispersion Slope shall be less than and equal to 0.092 ps/nm2km. ii) Zero Dispersion Wavelength shall range from 1,300 nm to 1,324 nm. The attenuation coefficient of the fibre shall be as follows: i) Maximum 0.4 dB/km – from 1,310nm to 1,625nm regions. ii) Maximum 0.4 dB/km in the 1,383 nm ±3 nm region. iii) Maximum 0.3 dB/km in the 1,550 nm region. g) PMD coefficient - PMD link design value shall be maximum of 0.2 ps/√km in accordance with ITUT G.657 class A (12/2006) Clause 7. h) Optical fibre shall be placed within fibre micro ducts having properties such as: i) low flammability; ii) low smoke; iii) low acid/fume; and iv) low halogen. i) The construction of the in-building fibre shall be 1 fibre or 2 fibre cores. j) The colour coding shall be as Table A.1. 39 MCMC MTSFB TC G024:2020 Table A.1 Blown fibre cable colour coding Number 1 2 Fibre Blue Yellow MCMC MTSFB TC G024:2020 Annex B (informative) Sample of core assignment The sample core assignment as shown in Table B.1. Table B.1. Sample of core assignment Core number Cable number Cable number FWS Port Cable number Vertical Cable 1 FV0 01 1 101 13 FV0 01 13 201 25 FV0 01 25 301 37 FV0 01 37 Spar e 2 FV0 01 2 101 14 FV0 01 14 201 26 FV0 01 26 301 38 FV0 01 38 Spar e 3 FV0 01 3 102 15 FV0 01 15 202 27 FV0 01 27 302 39 FV0 01 39 Spar e 4 FV0 01 4 102 16 FV0 01 16 202 28 FV0 01 28 302 40 FV0 01 40 Spar e 5 FV0 01 5 103 17 FV0 01 17 203 29 FV0 01 29 303 41 FV0 01 41 Spar e 6 FV0 01 6 103 18 FV0 01 18 203 30 FV0 01 30 303 42 FV0 01 42 Spar e 7 FV0 01 7 104 19 FV0 01 19 204 31 FV0 01 31 304 43 FV0 01 43 Spar e 8 FV0 01 8 104 20 FV0 01 20 204 32 FV0 01 32 304 44 FV0 01 44 Spar e 9 FV0 01 9 105 21 FV0 01 21 205 33 FV0 01 33 305 45 FV0 01 45 Spar e 10 FV0 01 10 105 22 FV0 01 22 205 34 FV0 01 34 305 46 FV0 01 46 Spar e 11 FV0 01 11 106 23 FV0 01 23 206 35 FV0 01 35 306 47 FV0 01 47 Spar e 12 FV0 01 12 106 24 FV0 01 24 206 36 FV0 01 36 306 48 FV0 01 48 Spar e 41 Core number Vertical Cable Cable number Vertical Cable FWS Port Cable number Core number Cable number FWS Port Vertical Cable FWS Port 1 Cable number FWS subrack Core number 1 Cable number FWS number MCMC MTSFB TC G024:2020 Table B.1. Sample of core assignment (continued) FWS number 1 FWS subrack 2 Cable number FWS Port Cable number Core number FV0 02 13 501 25 FV0 02 25 601 37 FV0 02 37 Spar e 2 FV0 02 2 401 14 FV0 02 14 501 26 FV0 02 26 601 38 FV0 02 38 Spar e 3 FV0 02 3 402 15 FV0 02 15 502 27 FV0 02 27 602 39 FV0 02 39 Spar e 4 FV0 02 4 402 16 FV0 02 16 502 28 FV0 02 28 602 40 FV0 02 40 Spar e 5 FV0 02 5 403 17 FV0 02 17 503 29 FV0 02 29 603 41 FV0 02 41 Spar e 6 FV0 02 6 403 18 FV0 02 18 503 30 FV0 02 30 603 42 FV0 02 42 Spar e 7 FV0 02 7 404 19 FV0 02 19 504 31 FV0 02 31 604 43 FV0 02 43 Spar e 8 FV0 02 8 404 20 FV0 02 20 504 32 FV0 02 32 604 44 FV0 02 44 Spar e 9 FV0 02 9 405 21 FV0 02 21 505 33 FV0 02 33 605 45 FV0 02 45 Spar e 10 FV0 02 10 405 22 FV0 02 22 505 34 FV0 02 34 605 46 FV0 02 46 Spar e 11 FV0 02 11 406 23 FV0 02 23 506 35 FV0 02 35 606 47 FV0 02 47 Spar e 12 FV0 02 12 406 24 FV0 02 24 506 36 FV0 02 36 606 48 FV0 02 48 Spar e Cable number Core number 13 Cable number FWS Port 401 Cable number 1 Cable number Cable number Vertical Cable Core number Vertical Cable FV0 02 Core number FWS Port Vertical Cable 1 Cable number FWS Port Vertical Cable MCMC MTSFB TC G024:2020 Table B.1. Sample of core assignment (continued) FWS number 1 FWS subrack 3 Cable number FWS Port Cable number Core number FV0 03 13 801 25 FV0 03 25 901 37 FV0 03 37 Spar e 2 FV0 03 2 701 14 FV0 03 14 801 26 FV0 03 26 901 38 FV0 03 38 Spar e 3 FV0 03 3 702 15 FV0 03 15 802 27 FV0 03 27 902 39 FV0 03 39 Spar e 4 FV0 03 4 702 16 FV0 03 16 802 28 FV0 03 28 902 40 FV0 03 40 Spar e 5 FV0 03 5 703 17 FV0 03 17 803 29 FV0 03 29 903 41 FV0 03 41 Spar e 6 FV0 03 6 703 18 FV0 03 18 803 30 FV0 03 30 903 42 FV0 03 42 Spar e 7 FV0 03 7 704 19 FV0 03 19 804 31 FV0 03 31 904 43 FV0 03 43 Spar e 8 FV0 03 8 704 20 FV0 03 20 804 32 FV0 03 32 904 44 FV0 03 44 Spar e 9 FV0 03 9 705 21 FV0 03 21 805 33 FV0 03 33 905 45 FV0 03 45 Spar e 10 FV0 03 10 705 22 FV0 03 22 805 34 FV0 03 34 905 46 FV0 03 46 Spar e 11 FV0 03 11 706 23 FV0 03 23 806 35 FV0 03 35 906 47 FV0 03 47 Spar e 12 FV0 03 12 706 24 FV0 03 24 806 36 FV0 03 36 906 48 FV0 03 48 Spar e 43 Cable number Core number 13 Cable number FWS Port 701 Cable number 1 Cable number Cable number Vertical Cable Core number Vertical Cable FV0 03 Core number FWS Port Vertical Cable 1 Cable number FWS Port Vertical Cable MCMC MTSFB TC G024:2020 Table B.1. Sample of core assignment (concluded) Vertical Cable Core number Unit number Core number Unit number Cable number Core number Unit number Vertical Cable Unit number FWS Port Vertical Cable Core number Cable number FWS Port Vertical Cable FWS Port 4 Cable number FWS subrack FWS Port 1 Cable number FWS number 1 FV0 04 1 100 1 13 FV0 04 13 110 1 25 FV0 04 25 120 1 37 FV0 04 37 Spar e 2 FV0 04 2 100 1 14 FV0 04 14 110 1 26 FV0 04 26 120 1 38 FV0 04 38 Spar e 3 FV0 04 3 100 2 15 FV0 04 15 110 2 27 FV0 04 27 120 2 39 FV0 04 39 Spar e 4 FV0 04 4 100 2 16 FV0 04 16 110 2 28 FV0 04 28 120 2 40 FV0 04 40 Spar e 5 FV0 04 5 100 3 17 FV0 04 17 110 3 29 FV0 04 29 120 3 41 FV0 04 41 Spar e 6 FV0 04 6 100 3 18 FV0 04 18 110 3 30 FV0 04 30 120 3 42 FV0 04 42 Spar e 7 FV0 04 7 100 4 19 FV0 04 19 110 4 31 FV0 04 31 120 4 43 FV0 04 43 Spar e 8 FV0 04 8 100 4 20 FV0 04 20 110 4 32 FV0 04 32 120 4 44 FV0 04 44 Spar e 9 FV0 04 9 100 5 21 FV0 04 21 110 5 33 FV0 04 33 120 5 45 FV0 04 45 Spar e 10 FV0 04 10 100 5 22 FV0 04 22 110 5 34 FV0 04 34 120 5 46 FV0 04 46 Spar e 11 FV0 04 11 100 6 23 FV0 04 23 110 6 35 FV0 04 35 120 6 47 FV0 04 47 Spar e 12 FV0 04 12 100 6 24 FV0 04 24 110 6 36 FV0 04 36 120 6 48 FV0 04 48 Spar e Acknowledgements Members of the Fixed Network Facility Sub-Working Group Mr Mohd Yusairi Abu Hassan (Chairman) Telekom Malaysia Bhd Mr Zulkefli Zabri (Vice Chairman) Maxis Broadband Sdn Bhd Mr Sufian Sulaiman (Secretary) Telekom Malaysia Bhd Mr Low Kien Yap/ Celcom Axiata Berhad Mr Muhammad Zainul Arifin Ab Aziz/ Mr Raja Zahiruddin Raja Muda Mr Ahmad Fadzly Misron Digi Telecommunications Sdn Bhd Mr Irma Syafrida Abd Majid edotco Malaysia Sdn Bhd Mr Mohd Mokhtar Daud Mr Mohamad Isa Mohd Razhali Malaysia Digital Economy Corporation Sdn Bhd Measat Broadcast Network System Sdn Bhd Mr See Boon Leng/ Mr Leong Woon Min Mr Najib Fadil Mohd Bisri @ Bisri Redsun Engineering Sdn Bhd Mr Mohd Faiz Hasmi TIME dotCom Berhad Ir Dr Anas Abdul Latiff Universiti Teknikal Malaysia Melaka Telekom Malaysia Bhd By invitation: Mr Jeysudason Allo Technology Sdn Bhd Mr Kuo Hai Ann Zettabits Technologies (M) Sdn Bhd