a
ATTACH TO CLIPBOARD HERE
Ttp: uSE THE
o
HORTZONTAL L|NE
tN THE CENTER OF THE PAGE TO AUGN YOUR T-SqqEE.
THE PRINCIPAL VIEWS IN THE MULTIVIEW DRAWING BELOW HAVE BEEN TRANSFERRED ONTO THE
ISOMETRIC CONSTRUCTION BOX. STUDY THE MULTIVTEW DRAWING, THEN, USING A PENCIL, LIGHTLY
.SHADE IN" THE AREAS ON EACH PLANE OF THE CONSTRUCTION BOX WHERE A SURFACE OF THE
MULTIVIEW WOULD BE PLACED.
rAus= TooLS To DRAWAN lsoMETRlc vlEW oF THE
\,/uulrvrEw (ABovE). BEGTN BY DRAWTNG A LTGHT
CONSTRUCTION BOX STARTING AT POINT "A". THEN
DRAWTHE OUTLINE OF THE AREAS YOU SHADED IN
STEP 1, FOLLOWED BY THE REST OF THE ISOMETRIC
o
CREATE A FREEHAND SKETCH OF THE ISOMETRIC
YOU DREW (AT LEFT)). BEGIN BY DRAWING A
LIGHT CONSTRUCTION BOX. THE STARTING POINT
"A'IS GIVEN.
LINES.
SPEED SCHOOL OF ENGINEERING
ENGINEERING GRAPHICS
NAME-1
<i )a/tf
I
,r r\
Ll^^atiil,{
-1
ll*\lt,t
SECTION
c)l
TEAM NO.
X
DRAWING NO.
:<A
ATTACH TO CLIPBOARD HERE
TIP: USE THE HORIZONTAL LINE IN THE CENTER OF THE PAGE TO ALIGN YOUR T-SQUARE.
THE PRINCIPAL VIEWS IN THE MULTIVIEW DRAWING BELOW HAVE BEEN TRANSFERRED
ONTO THE
ISOMETRIC CONSTRUCTION BOX. STUDY THE MULTIVIEW DRAWING, THEN, USING
A PENCIL, LIGHTLY
"SHADE IN" THE AREAS ON EACH PLANE OF THE CONSTRUCTION BOX WHERE A SURFACE
OF THE
MULTIVIEW WOULD BE PLACED.
A
A
a
USE TOOLS TO DRAW AN ISOMETRIC VIEW OF THE
MULT|V|EW (ABOVE). BEGTN By DRAWTNG A LteHT
CONSTRUCTION BOX STARTING AT POINT'A-. THEN
DRAW THE OUTLINE OF THE AREAS YOU SHADED IN
STEP 1. CONTINUE WITH ISOMETRIC LINES,
FOLLOWED BY ANY OBLIQUE LINES.
SPEED SCHOOL OF ENGINEERING
ENG!NEERING GRAPHICS
CREATE A FREEHAND SKETCH OF THE ISOMETRIC
YOU DREW (AT LEFT). BEGIN BY DRAWING A
LIGHT CONSTRUCTION BOX, THE STARTING POINT
'A'IS GIVEN.
ATTACH TO CLIPBOARD HERE
TIP: USE THE HORIZONTAL UNE lN THE CENTER OF THE PAGE TO ALIGN YOUR T-SQUARE.
REFER TO THE MULTIVIEW BELOWTO CREATE OTHER
VIEWS AS INSTRUCTED. USE A SCALE TO DETERMINE
DIMENSIONS FROM THE MULTIVIEW.
CREATE A FREEHAND SKETCH OF THE ISOMETRIC
sHowN (ABOVE-RIGHT). BEGIN BY DRAWTNG A LTGHT
CONSTRUCTION BOX. STARTING POINT "A' FOR THE
CONSTRUCTION BOX IS GIVEN.
USE TOOLS TO DRAW AN ISOMETRIC VIEW OF THE
MULTTVTEW (AT LEFT). BEGTN BY DRAWTNG A LTGHT
CONSTRUCTION BOX STARTING AT POINT "A".
USE TOOLS TO RE-CREATE THE MULTIVIEW SHOWN
(ABOVE LEFT). BEG|N BY DRAWTNG LTGHT BOXES FOR
EACH VIEW. USE A MITER LINE. THE STARTING POINT
FOR THE FRONT VIEW "A" IS GIVEN.
i i- ,
r".
a
i '---1-]_j
t'\''1
i
I
i
lr
it"
SPEED SCHOOL OF ENGINEERING
ENGINEERING GRAPHICS
NAME
'Y
I
_. *___l-*.
SECTION
TEAM NO.
DRAWING NO.
3(l
ATTACH TO CLIPBOARD HERE
YOUR T-SQUARE'
TIP: USE TTIE HORIZONTAL UNE IN THE CENTER OF THE PAGE TO ALIGN
REFER TO THE MULTIVIEW BELOW TO CREATE OTHER
VIEWS AS INSTRUCTED. USE A SCALE TO DETERMINE
DIMENSIONS FROM THE MULTIVIEW.
USE TOOLS TO COMPLETE THE ISOMETRIC DRAWING
BELOW OF THE OBJECT SHOWN (AT LEFT). USE AN
ELLIPSE TEMPLATE TO ADD HOLES AND ROUND THE
FRONT CORNER OF THE BASE.
+
COMPLETE THE DRAWING BELOW OF THE ISOMETRIC
DRAWING SHOWN (ABOVE-RIGHT). USE FREEHAND
SKETCHING TECHNIQUES TO ADD THE MISSING
USE TOOLS TO COMPLETE THE MULTIVIEW BELOW'
.REFER TO THE MULTIVIEW SHOWN (ABOVE LEFT) FOR
DIMENSIONS.
COMPONENTS.
+
+
SPEED SCHOOL OF ENGINEERING
ENGINEERING GRAPHICS