Operator’s Manual
with Parts List
April 2002
Operator’s Manual
Copyright © FMC Technologies, Inc. 2002
FMC FoodTech Citrus Systems
400 Fairway Avenue
Lakeland, FL 33801
(863) 683-5411
2
FMC Technologies, Inc. Juice Extractor Operator's Manuals
Safety Information …………….………………..….….….
4
Safety Instructions ......................…............……..……..
5
Technical Specifications ……………………….…..……
6
Operating Instructions ........................………..…..……
8
Equipment Check ..........................….............……..…..
10
Juicing ....................………......................…...…..…..….
11
Cleaning Instructions ..........…….................…...…...…
13
Exploded View of Juicing Components ........…………
15
Maintenance ........……………………………………….…
18
Troubleshooting ...………………………………………...
21
Parts Listing ..........................….............……..………….
24
FMC Technologies, Inc. Juice Extractor Operator's Manuals
3
IMPORTANT SAFETY INFORMATION
You can help prevent personal injury and/or property damage.
Please read this manual carefully before operating the FMC FoodTech Extractor.
Do NOT attempt any operation until you understand exactly how the machine
functions.
If uncertainty remains after studying this manual, please contact:
FMC Technologies, Inc.
FMC FoodTech
Citrus Systems
400 Fairway Avenue
Lakeland, FL 33801
(863) 683-5411
or
The local FMC FoodTech service representative in your country.
We're here to help. With proper handling, the FMC FoodTech Juice Extractor will provide
safe, efficient and convenient service for years to come.
4
FMC Technologies, Inc. Juice Extractor Operator's Manuals
Safety Labels
The safety labels shown below appear on the Juicer Extractor. They provide essential
instructions on how to avoid possible hazards.
Please, for your safety:
FOLLOW THOSE INSTRUCTIONS AT ALL TIMES.
Should the Juicer safety labels become damaged or unreadable, contact FMC
FoodTech for replacement labels.
Safety Instructions
Carefully review the following safety instructions.
Make them a habit when using the FMC FoodTech Juice Extractor.
1.
2.
3.
4.
5.
6.
If extractor continues to run when any access cover is open, interlock switch is
defective.
Turn Juicer off immediately. Call for service.
Prevent unauthorized access to Extractor by locking all covers with supplied key.
Prevent unauthorized operation of Extractor by placing electrical plug inside cart
door.
NEVER attempt to make any safety device inoperative.
NEVER operate or perform maintenance or repair work on Extractor when taking
any kind of drug or sedative, when under the influence of alcohol, or when fatigued.
ALWAYS check adjustment of all nuts, bolts, and screws after installation, repair,
or periodic maintenance.
FMC Technologies, Inc. Juice Extractor Operator's Manuals
5
TECHNICAL SPECIFICATIONS
Fruit size: 2 - 1/2" to 3 - 7/8" diameter
Oranges - FL: ...................…….. 125 to 50 count
Oranges-CA: ....................…….. 138 to 48 count
Grapefruit - FL: ................……... 56 to 48 count
Hopper capacity: ....................…….. 40 Ib. (1 carton)
Reservoir capacity:.................…….. 3 - 1/2 gal. (1 carton)
Waste container capacity: .....……... 40 Ib. of peel (2 cartons)
Speed:....................................……... 20 fruit/minute
(20 to 60 gallons/hour)
ELECTRICAL SPECIFICATIONS
115V 60H2 Single Phase 20 AMP Service
12 GA. wire -up to 100 ft. from main breaker panel
or 10 GA. wire - up to 200 ft. from main breaker panel
Dedicated line needed for Juicer.
SHIPPING SPECIFICATIONS
Machine With Stand:
Height: 67"
Width: 27"
Depth: 32"
Weight:
535 Ibs
PATENTS
U.S. Patents - #4905586 and #4922814
& Patents Pending
6
FMC Technologies, Inc. Juice Extractor Operator's Manuals
GENERAL INFORMATION
The FMC FoodTech Juice Extractor is designed to provide years of dependable service.
It uses a unique patented design to extract every available amount of juice from the fruit
with the least amount of peel oil. The peel is completely separated from the juice and
juice sacs before being compressed and strained.
The machine will juice all types of citrus — oranges, grapefruits, lemons, limes,
tangerines, etc. — without changing or adjusting parts. In fact, different varieties and
sizes of fruit can be juiced to create various fruit juice blends
Clean-up is simple, requiring disassembly of only five parts. All waste material — peel,
membranes, and seeds — is collected in a disposable garbage bag for easy removal
and disposal.
The Juice Extractor is solidly built using heavy-duty components in all assemblies,
including the drive. It is simple to operate and uses a minimal number of parts.
ALWAYS follow cleaning and maintenance schedules in this manual to prevent
equipment damage.
For a quick introduction to the FMC FoodTech Juice Extractor, please review the
diagram on the next page.
Operating instructions begin on page 10.
FMC Technologies, Inc. Juice Extractor Operator's Manuals
7
Figure 1a. FMC FoodTech Juice Extractor
8
FMC Technologies, Inc. Juice Extractor Operator's Manuals
Figure 1b. Juicing Components Assembly
Figure 1c. Inside Cart Door
FMC Technologies, Inc. Juice Extractor Operator's Manuals
9
OPERATING INSTRUCTIONS
EQUIPMENT CHECK
Before plugging the FMC FoodTech Juice Extractor into an electrical outlet, the
following steps must be performed:
1.
Locate the Juice Extractor on a level surface.
This will prevent fruit feed problems.
2.
Lock both rear casters.
To lock, push down on caster with foot. To unlock, push again with foot.
3.
Check waste container.
Open cart door to verify that waste container is in place. A plastic bag may be
attached to the hooks above the waste container (recommend the "Hefty Cinch
Sak®", 30 gallon capacity or equivalent).
4.
Check juicing components.
a. Twist and pull juice nozzle off.
b. Use key to unlock juicing components cover. Open cover and check that
juicing components are installed and securely fastened. See Figure 1b,
page 9.
5.
Close and lock all access covers.
There are 4 separate access covers: hopper cover, juicing components cover,
cart door (cover) and back cover.
NEVER operate extractor unless all covers are in place.
6.
Replace juice nozzle.
7.
Make sure Juice reservoir is firmly in place.
8.
Make sure juice reservoir valve is in closed position.
9.
Check the hopper for foreign objects.
Remove any foreign objects found in the hopper.
10.
10
Make sure floor area around extractor is clean and free of obstructions and
water.
When water is necessary, wear appropriate non-slip footwear.
FMC Technologies, Inc. Juice Extractor Operator's Manuals
OPERATING INSTRUCTIONS
Juicing
CAUTION:
DO NOT run Extractor without fruit for more than one minute.
Equipment damage will result.
1.
Turn on Extractor.
Push the "ON-OFF" button to "ON" position.
2.
Fruit may be fed into Extractor one at a time (Single Feed) or in bulk.
a. Single Feed
Remove hopper single feed hole cover.
Twist and pull cover to remove.
Drop fruit individually down single-feed chute through hole in hopper cover.
Do NOT overload chute or fruit will accidentally be double fed.
b. Bulk Feed
Unlock and open the hopper cover.
Dump up to one carton (40 Ibs.) of fruit into the hopper.
Fruit may be divided between the carton and carton lid for ease of lifting.
3.
Do NOT use the single-feed chute when hopper is full.
Fruit will accidentally be double fed.
4.
Turn-off Extractor.
Push the "ON-OFF" Switch to the "OFF" position.
5.
Stir juice.
Use stirrer handle to stir juice in reservoir before filling containers.
6.
Fill containers.
Place container under juice reservoir valve. Open valve by turning lever until
container is full.
7.
Clean Extractor.
If finished juicing, clean Extractor as soon as possible.
(See next page for cleaning instructions.)
FMC Technologies, Inc. Juice Extractor Operator's Manuals
11
CLEANING INSTRUCTIONS
ALWAYS follow cleaning and maintenance schedules in this manual to prevent
equipment damage.
Clean Extractor as soon as possible for juicing. Use a soft towel or sponge to wipe
equipment parts. Do not use abrasive pads such as Scotch Brite®, steel wool, etc
The recommended cleaner is "Pelican" brand Peralkalate. Peralkalate is a low-foaming
alkaline equipment cleaner. It is safe on aluminum, 100% water soluble and free rinsing.
Peralkalate has been especially formulated for cleaning food processing equipment and
is USDA accepted. Follow instructions on cleaner label for dilution.
1.
Turn-off Extractor with Juicing Component cups separated.
2.
DISCONNECT ELECTRICAL PLUG.
3.
Pull Extractor to clean-up area, if one is available.
4.
Brush all loose peel into waste container or bag.
5.
Empty and rinse waste container.
Continued on Next Page
12
FMC Technologies, Inc. Juice Extractor Operator's Manuals
CLEANING INSTRUCTIONS
6.
Remove juicing components.
a. Cups should be separated. (Extractor should have been turned off with
cups in the separated position.)
b. Grasp upper cup and pull out pin just above it. Place upper cup in waste
container.
CAUTION:
DO NOT PLACE HANDS OR FINGERS BETWEEN CUPS.
c. Remove splatter shield by sliding upwards off mounting screws.
d. Remove lower cup by removing spanner nuts on either side of lower cup.
(A spanner wrench is provided to loosen/tighten spanner nuts).
Place lower cup in waste container.
CAUTION:
CUTTER AND KNIVES ARE SHARP.
e. Install red protective cap on cutter.
(Red protective cap is provided.)
f.
Grasp juice manifold and orifice tube firmly. Remove entire juicing
components assembly.
g. Grasp orifice tube and pull out of strainer tube.
h. Remove strainer tube from inside juice manifold by turning tube counterclockwise and sliding out. (A spanner wrench is provided to loosen/tighten
strainer tube.)
Place juicing components into waste container.
FMC Technologies, Inc. Juice Extractor Operator's Manuals
13
14
FMC Technologies, Inc. Juice Extractor Operator's Manuals
Figure 2. Juicing Components
7.
Prepare cleaning solution.
"Pelican" brand Peralkalate is recommended, see page 13.
Read the product label. Follow the manufacturer's mixing directions and safety
precautions.
8.
Immerse all components in cleaning solution.
Use the blunt end of plastic rod provided to displace any fruit material lodged in
the bore of the orifice tube.
Use pointed end of plastic rod to displace any fruit material lodged in cup fingers.
9.
Scrub components.
Use a brush, towel, or sponge. Do not use abrasive pads such as Scotch Brite",
steel wool, etc. Thoroughly rinse with clean water, then thoroughly rinse with
sanitizer solution. Follow the manufacturer's mixing directions and safety
precautions.
10.
For best results, soak strainer tube overnight.
After soaking overnight, rinse the strainer tube thoroughly before using. Check
that all strainer tube holes are clean. Clean strainer tube with a hard spray from
a hose while moving orifice tube back and forth in strainer tube. Rinse
thoroughly with sanitizer solution. Allow to air dry.
11.
If possible, hose down juicing area and cover.
If location prohibits using a hose to clean juicing area and cover, ensure waste
container is in place. Wash down the exposed juicing area and cover with a
sponge or spray applicator using the recommended cleaning solution. Cover may
be rinsed in place or removed by lifting it off the hinges. Allow to stand for two
minutes before rinsing thoroughly with water.
12.
Re-assemble juicing components.
Start by re-assembling strainer tube into juice manifold. Tighten with spanner
wrench. Insert orifice tube into bottom of strainer tube. Mount juice manifold
assembly onto locating pins with orifice tube notch engaging lower drive. Tighten
spanner screw with spanner wrench. Remove red protective cap from cutter.
Install lower cup and tighten spanner nuts with spanner wrench. Install upper cup
by slipping pin into stem hole. Install splatter shield.
Refer to Figure 2, page 15.
FMC Technologies, Inc. Juice Extractor Operator's Manuals
15
13.
As necessary, hose down drive area.
Remove back cover (Turn lock at top 1/4 counter-clockwise.
Pull cover out by using finger hole left of lock, then lift and pull cover using finger
hole on bottom. DO NOT loosen any screws.) Open hopper cover. Open cart
door (cover). Hose down all exposed areas. Extractor is water-resistant. Do not
use any cleanser in drive area.
14.
Remove wax build-up as needed.
Cups, hopper and other parts may acquire a build-up of
wax over time.
a.
Soak cups for five minutes in an ammonia cleaning solution.
Rinse thoroughly with sanitizer solution.
b.
15.
Wipe hopper and other parts with a cloth soaked in ammonia cleaning
solution.
Remove orange discoloration as needed.
Equipment may exhibit some build-up or orange coloration over time. Peralkalate
Solution should remove this. Wipe with a cloth soaked in any pine based cleaner
(such as Pine Power" or Pine Spic & Span'"') to remove discoloration from plastic
covers.
Rinse thoroughly with sanitizer solution.
16.
16
Clean Tomlinson faucet.
Daily cleaning is crucial to the performance, maintenance and sanitation of the
faucet.
Take apart handle assembly and flush with clean water, then sanitize.
FMC Technologies, Inc. Juice Extractor Operator's Manuals
MAINTENANCE
Before performing any maintenance,
DISCONNECT ELECTRICAL PLUG.
Extractor requires no lubrication.
DO NOT LUBRICATE ANY BEARING, ROD END, OR SHAFT.
After every juice run:
1.
Check cutter and knives for sharpness.
Refer to Figure 3 to determine condition of cutter.
If dull, sharpen with a whetstone provided.
Refer to Figure 4a to sharpen cutter.
If cutter is severely damaged or rolled over, replace cutter.
a.
Cutter removal:
Disassemble juicing components per Figure 2, page 15 Loosen set screw under
front knife (make sure screw is backed out far enough to clear cutter). Cutter
should lift out. If not, tap the cutter lightly from inside the juice manifold with a 11/4" dia rod (hammer handle).
CAUTION: CUTTER AND KNIVES ARE SHARP.
Install red protective cap provided onto cutter. After red protective
cap is installed, remove cutter. Handle cutter with care to avoid direct contact
with sharp edge.
b.
Cutter installation.
Align arrows on cutter and juice manifold to seat cutter. Make sure cutter is fully
seated. Tighten setscrew.
(Do NOT over-tighten)
FMC Technologies, Inc. Juice Extractor Operator's Manuals
17
Figures 3. Installation of good cutter
Figure 3a. Bad cutter- REPLACE cutter
Figure 3b. Cutter that can be sharpened
Figure 4a. Sharpening Cutter
with Whetstone
18
Figure 4b. Sharpening knife
with Whetstone
FMC Technologies, Inc. Juice Extractor Operator's Manuals
MAINTENANCE
2. Check orifice tube for damage.
Refer to Figure 5
Replace tube when:
a.
Chunks are missing from top end.
b.
Score marks 1/32" or deeper appear along the length of the tube.
Figure 5. Severely Damaged Orifice Tube
3. Check for loose or missing nuts and bolts.
a.
b.
Tighten or replace nuts and bolts as necessary.
DO NOT exceed torque ranges specified in Service Manual
ALWAYS use FMC FoodTech recommended spare parts.
FMC Technologies, Inc. Juice Extractor Operator's Manuals
19
TROUBLE SHOOTING
CAUTION:
NEVER reach into moving parts to clear a jam, no matter how
simple it seems.
Extractor will not start.
1.
Extractor is not plugged into electrical outlet.
2.
Building circuit breaker has tripped.
3.
All covers are not completely closed (including cart and back (cover).
4.
Equipment is jammed.
Call for service.
5.
"ON-OFF" switch is defective.
Call for service.
6.
Some linkage adjustment may be required on Juice Reservoir Float switch.
Extractor will not start, but buzzing sound comes from "ON-OFF" switch.
1.
2.
3.
Overloaded circuit.
Machine needs to be on separate
(own) electrical outlet.
One or more covers partially closed causing intermittent contact of interlock
switch.
Close and lock all covers.
Low voltage to machine.
Use 110 volts minimum.
Machine starts, but shuts off.
1.
2.
3.
4.
Building circuit breaker is not rated for 20 Amps.
Extension cord or wiring is too long.
Shorten extension cord or use heavier gauge wire.
(See page 6, "Specifications")
All covers are not completely closed (including cart).
Close any open covers.
One or more covers has a defective interlock switch.
Turn off Extractor. Call for service.
Extractor runs with covers open or off.
Turn off Extractor. Call for service.
20
FMC Technologies, Inc. Juice Extractor Operator's Manuals
TROUBLE SHOOTING
Extractor stalls trying to squeeze a fruit.
1. Fruit has part of stem on it.
Turn off Extractor. Remove fruit from Extractor and restart.
2. Peel is too thick.
Turn off Extractor. Remove fruit from Extractor and restart.
3. Cutter is damaged.
Sharpen or replace cutter as specified on page 18.
Extractor emits a "squealing" sound during operation.
1. Lubricate grease fittings on machine.
If noise continues rod end or linear bearing is defective.
Turn off Extractor. Call for service.
LOW JUICE YIELD.
Excessive juice splattering during juicing operation.
1. Fruit is rotten or fruit stems are pulled.
Remove unsuitable fruit.
2. Orifice tube is damaged.
See page 20 to determine if it needs replacement.
3. Strainer tube is plugged.
Clean strainer tube. See page 16.
4. Check for excessive cup wear.
Replace Cups
Fruit rolls out of cup
1. Splatter shield has not been installed.
Install splatter shield as specified on page 15.
FMC Technologies, Inc. Juice Extractor Operator's Manuals
21
TROUBLE SHOOTING
Fruit is being chopped instead of juiced.
1. Fruit is too large for machine.
Turn off Extractor. Remove oversized fruit. Maximum diameter is 3-7/8".
2. Fruit feeder is sticky or unclean.
Turn off Extractor. Remove fruit.
Clean fruit lift as specified on page 16-17.
3. Extractor’s not level. Locate Extractor on level surface.
Fruit is fed two at a time.
1. Fruit is too small for machine.
Turn off Extractor. Remove undersized fruit. Minimum diameter is 2-1/2"
2. Fruit is too small for machine.
Fruit is not fed during every cycle.
1. The hopper mechanism is designed to put fruit into a single file and to break-up bridging
before feeding. When hopper is full, it sometimes takes a couple of cycles to begin
feeding. Hopper will feed faster when half full.
Hopper emits a scraping noise.
1. Fruit lift mechanism is dragging on hopper.
Turn off Extractor. Call for service.
Cutter is constantly being damaged.
1. Red protective cap is not being placed on cutter prior to removing juice manifold and
during handling.
2. Fruit was put in single feed chute when hopper was full.
Use supplied spanner wrench to tighten spanner screw on juice manifold.
22
FMC Technologies, Inc. Juice Extractor Operator's Manuals
Drive Parts
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
44
45
46
47
48
Part Number
004405131
06000064
06000030
005098731
005220145
005221291
06000010
06000062
005098732
005098113
005576249
004355116
004352571
005098727
004116037
005806227
06000065
005098112
005576242
004352404
004806070
004816080
06000061
06000057
004352661
004816120
005098729
004116046
06000060
004116047
005098730
06000078
06000009
005576246
06000059
004116038
06000068
06000011
005098728
004352572
004816100
06000058
004352398
004352392
06000066
06000063
005576061
Description
SCREW,MFJ,CAP,ST SKT,C/G
SHAFT,LINEAR,UPPER
ARM,UPPER CUP DRIVE
BEARING,1"x 1"
CHAIN,MFJ (5.1 FEET/BAG)
LINK,CONN SPG PLN FOR #60
SPROCKET,DRIVE,UPPER CUP
SHAFT,ROTARY DRIVE,UPPER
BEARING,1-1/4" x 1-1/4"
WASHER,MFJ,THRUST,1-1/4"
KEY,MFJ,SQ,1/4"x 1-1/2",SS 416
SCREW,MFJ,CAP,SOC,3/8-16x2,C/G
SCREW,MFJ,CAP,HEX,1/2-13x1-1/2
ROD END,MALE,RH,1/2MM-8T,AUTO
NUT,MFJ,JAM HEX,1/2-20
SPROCKET w/ Set Screw
SPROCKET,DRIVE,ORIFICE
WASHER,MFJ,THRUST
KEY,MFJ,SQ,1/4"x 1",SS 416
SCREW,MFJ,CAP,HEX,3/8-16x1-3/4
WASHER,MFJ,LOCK REG,3/8,SS
WASHER,PLAIN N,3/8,SS
SHAFT,ROTARY DRIVE,LOWER
LOCK,ROD END
SCREW,MFJ,CAP,HEX,5/8-11x2-1/2
WASHER,MFJ,PLAIN N,5/8
ROD END,RH 5/8",AM-10TZ W/PTF
NUT,MFJ,JAM HEX,5/8-18
LINKAGE,CUP DRIVE
NUT,MFJ,JAM HEX LH,5/8-18
ROD END,LH,#AB-10TZ,W/PTFE LIN
SCREW,UPPER CUP CRANK LH
CRANK,UPPER CUP DRIVE
KEY,MFJ,SQ,1/4"x 1-1/4",SS 416
LINKAGE,ORIFICE DRIVE
NUT,MFJ,JAM HEX LH,1/2-20
BEARING,FRUIT LIFT
ARM,ORIFICE TUBE DRIVE
ROD END,MALE LH,1/2,MB-8T AURO
SCREW,MFJ,CAP,HEX,LH
WASHER,MFJ,PLAIN N,1/2,SS
ORIFICE CRANK ARM
SCREW,MFJ,CAP,HEX,3/8-16x1-1/4
SCREW,MFJ,CAP,HEX,3/8-16x7/8
BASE FOR GEARMOTOR
SHAFT,LINEAR,LOWER
KEY,MFJ,SQ,1/4" X 3/4",SS 416
FMC Technologies, Inc. Juice Extractor Operator's Manuals
23
24
FMC Technologies, Inc. Juice Extractor Operator's Manuals
JUICING AND CART PARTS
Item Part Number
1
2
3
4
5
6
6a
6a1
6a2
6a3
6a4
7
8
9
10
11
12
13
13a
14
14a
14b
15
16
17
18
20
21
22
23
24
24a
25
26
27
28
29
30
31
32
34
35
36
37
38
39
40
41
42
43
44
45
46
47
06000056
004226039
06000071
004401022
06000027
06000111
06001054
06001024
0600102401
004401022
004156041
06000004
06000225
004406003
06000051
06000108
007486119
06000022
06001059
06000086
06000208
06000230
06000008
06000055
06000077
009092022
004352315
06000038
004352410
004816080
06000043-01
0600004301
06000098
06000028
004352398
06000089
06000068
06000123
004461025
004111022
004352145
004816052
06000079
004111040
004816070
009080527
009080526
06000109
06000084
009710031
009080326
009092018
06000131
06000088
Description
PLATE,UPPER CUP: FDA GRADE
PIN,MFJ,FASPIN,3/8 D X 1-5/8
HINGE,COVER,FRONT,MALE
SCREW,MFJ,MACH TRS,NYLOK,PHILL
CUP,UPPER,MFJ
SHIELD,SPLATTER,CURVED (OLD STYLE)
Shield,Splatter,Assembly,90° Bend
Bracket,Clear Shield,Rh
Bracket,Clear Shield,Lh
Screw,Mach Trs,Nylok,Phil,10-24x3/8
Nut,Hex S/L,10-24,Ss
CUP,LOWER,MFJ
CUTTER W/SCREW,MFJ & CJ
SCREW,MFJ,MACH,RD,4-40x3/16,SS
SPANNER SCREW
MANIFOLD,JUICE
O-RING,NOZZLE,MFJ,1x1-1/8x1/16
NOZZLE,STRAIGHT,PLASTIC
Nozzle,Ss,90° Bend,Jamba
TUBE,STRAINER,MFJ,.033
Tube,Strainer,Mfj,.040
Tube,Strainer,Mfj,.055
TUBE,ORIFICE,MFJ
PLATE,ORIFICE DRIVE: FDA GRADE
TOOL,WRENCH
CONTAINER,19-1/2"X23-1/2"X13"
SCREW,MFJ,CAP,HEX,5/16-18x3/4
LIFT,FRUIT: FDA MATERIAL
SCREW,MFJ,CAP,HEX,3/8-16x2-1/4
WASHER,PLAIN N,3/8,SS
HOPPER ASSY,MFJ ABS,FIELD USE
Hopper Assy,Mfj Ss,Field Use
SPANNER NUT
GUIDE,FRUIT,FDA GRADE
SCREW,MFJ,CAP,HEX,3/8-15x1-1/4
BUTTON,HOPPER BUMP
BEARING,FRUIT LIFT
CLIP,LATCH
HOOK,MFJ
NUT,MFJ,HEX,#10-24,SS
SCREW,MFJ,CAP,HEX,#10-14,3/8
WASHER,MFJ,PLAIN,#10,SS
LOCATOR,WASTE BIN
NUT,HEX,5/16-18,SS
WASHER,MFJ,PLAIN N,5/16,SS
CASTER,RIGID,4",MFJ
CASTER,SWIVEL,4",MFJ
STUD,CUP,LOWER
ROD,ORIFICE CLEAN OUT,MFJ
STONE,SHARPENING
BRUSH,1-1/16" X 8",FNS
CAP,COVER
PERALKALATE CLEANER 750 M
RESTRICTOR,HOLE,SMALL FRUIT
FMC Technologies, Inc. Juice Extractor Operator's Manuals
25
26
FMC Technologies, Inc. Juice Extractor Operator's Manuals
ELECTRICAL PARTS
Item Part Number
Description
1
2,19
3
4
5
6
7
8,10
9
11
12
13
14
15
16
17
06000074
004401022
06000075
004352383
004816080
006040062
006190054
004397077
006221066
007146009
006060074
06000093
007146010
007486118
006060044
006210275
PANEL,ELECTRICAL BOX
SCREW,MFJ,MACH TRS,NYLOK,PHILL
PLATE,ELECTRICAL BOX
SCREW,MFJ,CAP,HEX,3/8-15x1/2
WASHER,PLAIN N,3/8,SS
COIL,UNDERVOLTAGE,MFJ
STARTER,MOTOR,SPRECH SCHUH
SCREW,MACH RD SLOTTED,8-32X 1/2
TERMINAL,BLOCK,#1505W CURTIS
NUT,MFJ,3/8"-18NPT
CONNECTOR,STRAIGHT,3/8",#2671
MOTOR - WIRE
NUT,MFJ,1/2"-14NPT
O-RING,MFJ,1/2 METAL CLAD
CONNECTOR,CORD GRIP,CORD RANGE
SWITCH,PROX 2 CONDUCTER CABLE
17A
006200267
SWITCH,SAFETY,SCHMERSAL
18
06000076
PLATE,BACK COVER
20
21
22
004440004
006270195
06000167
SCREW,MFJ,TAP,PAN"F"HEAD
CLIP,CORD,#ACC19-A PANDUIT
ELECTRICAL BOX,SPRECHER SCHUH
23
23A
23B
24
06000538
06000537
004430004
06000292
DIAPHRAGM,PUSH BUTTON
FRAME,ON/OFF SWITCH MEMBRANE
SCREW,TAP,FLT HD,"B",#4 X 3/8,PLATED,PHILLIPS
MOTOR ASSY,115/60,FIELD REPLCE
24A
25
26
27
06000293
006270194
006080067
006270021
MOTOR ASSY,220/50,FIELD REPLCE
CONNECTOR,HUB,90-.375/.500
CORD,12 GA TYPE SJO3 CONDUCTOR
PLUG,ELECTRICAL,THAILAND
27a
28
006080071
006050068
CORD,BLACK,15AMP PLG,10'LG
CABLE,MOUNT
29
006240027
TRANSFORMER (INTERNATIONAL ONLY)
*30
06000141
BRACKET,RESERVOIR SWITCH
*31
006210290
SWITCH,PROXIMITY,BLACK JACKET
32
06002087
SAFETY KEY FOR SCHMERSAL SWITCH
* For Machines equipped with high level switches
FMC Technologies, Inc. Juice Extractor Operator's Manuals
27
28
FMC Technologies, Inc. Juice Extractor Operator's Manuals
COVER PARTS
Item Part Number
1
1A
2
3
4
4A
5
6
7
8
9
9A
10
10A
11
12
13
14
15
16
17
17a
18
18a
19
20
21
22
23
24
24a
25
25a
26
27
28
29
30
31
32
33
34
35
*36
*37
*38
*39
40
06000033
06001040
06000125
06000122
06000044
06001041
004401022
06000072
06000120
006210276
06000045
06001061
009425019
004265016
06000025
06000036
06000097
06000162
004401024
06000216
06000047
06001055
06000035
06001053
004401026
06000073
06000082
06000110
009425020
06000032
06001060
06000046
06001042
06000090
06000083
06000107
06000080
06000193-01
06000193-03
009450034-01
009450035
009450031
009450033
009210013
06000137
06000140
006210291
009080050
Description
COVER,BACK: UL #R597016
COVER,BACK, SS
RETAINER,BACK COVER
SIGN,WARNING,MOVING JUICER
COVER,DRIVE: UL #R597016
COVER,DRIVE,SS
SCREW,MFJ,MACH TRS,NYLOK,PHILL
HINGE,COVER,FRONT,FEMALE
SIGN,WARNING,COVER SWITCHES
ACTUATOR,GEO,PROXIMITY,MFJ
COVER,JUICE: UL #R597016
COVER,JUICE,SS, ASSEMBLY
LATCH,SPRING TOOLHEAD
RIVET,1/8 DIA X 1/4 GRIP
RESERVOIR LID: FDA MATERIAL
RESERVOIR,JUICE,FDA MATERIAL
PIN,RESERVOIR HOLDER
FAUCET,SS MFJ & ABS MFJ
SCREW,MACH TRS,#10-24 X 1/2,SS
PLUG,HOPPER & SCREW,MFJ
COVER,DOOR: UL #R597016
COVER,DOOR,CART,SS
COVER,STAND: UL #R597016
COVER,MAIN,SS
SCREW,MFJ,MACH,TRS,PHILLIPS
HINGE,COVER,HOPPER
LABEL,MFJ,HOPPER: UL #NNP-101
PLUG,HOPPER: UL #R597016
KEY,TOOLHEAD,MFJ
COVER,HOPPER: UL #R597016
COVER,HOPPER,SS, ASSEMBLY
COVER,SWITCH; UL #R597016
COVER,SWITCH,SS
SPACER,SWITCH COVER
LABEL,MFJ,ON/OFF: UL #NNP-101
STIRRER
HINGE,DOOR,STAND
BUMPER, URETHANE X 26"LG
BUMPER, URETHANE X 7-1/2"LG
DECAL,BASE,FRUIT,MFJ RECESSED
DECAL,MFJ,STRIPE,RED
DECAL,MFJ,LOGO,FRESH'N SQUEEZE
DECAL,MFJ,ROOF,FRUIT
FLOAT,CYL,1-1/2D X 2-5/8,POLYP
FRAME,RESERVOIR FLOAT,PIVOT
MAGNET HOLDER,RESERVOIR
MAGNET,PROXIMITY
BUMPER,STEM TYPE,5/8"X15/16"L
* Machines equipped with high level switches
FMC Technologies, Inc. Juice Extractor Operator's Manuals
29
30
FMC Technologies, Inc. Juice Extractor Operator's Manuals
Operator's Manual
Copyright © FMC Technologies, Inc. 2002
FMC FoodTech Citrus Systems
400 Fairway Avenue
Lakeland, FL 33801
(863) 683-5411
Manual No. 060S07010.200