smartphone
App Guide
Smartphone Application Guide
Thank you for purchasing the Xrobot Robot Vacuum Cleaner.
This manual is an application guide for connecting the main unit and a smartphone.
Table of contents
①. Downloading and installing the "Huiba" app …………………………………… 1
②. Registration by mobile phone number ……………………………………………………………… 1
③. Turn on the power of the robot (main body) …………………………………………………… 2
④. Robot and application settings ……………………………………………………………… 2-3
⑤. Robot remote control …………………………………………………… 4
⑥. Addition of family members ………………………………………………………… 5-6
⑦. Cleaning reservation settings ………………………………………………………………………… 6
⑧. Explanation of function buttons ………………………………………………………………………… 7
⑨. Update ……………………………………………………………………………… 7
1 Download and install the "Huiba" app
Scan the QR code listed above or Android App / Apple Store
Search above,
Download the "Huiba" app (free).
2 Registration by mobile phone number
Open "Huiba".
② Enter your mobile phone number.
① Press the registration button.
③ Identification code and half-width alphanumeric characters
Password over 6 characters
Enter.
④ "Add a robot"
Press.
⑤ "Scan QR code"
<1>
Press to read the QR code of the robot.
3 robot
Turn on the power of (main unit)
Turn on the main power of the main unit. Function buttons are red to white
It will change to continuous lighting. After 25 seconds, a beep sounds and changes to blinking.
The preparation of the main body is completed.
* When the main power supply of the main unit is "OFF", charging and using a smartphone
I cannot access or operate the main unit. Please be careful.
Four Robot and app settings
2 Send Wi-Fi from the robot
1 Set up a robot administrator
"Wi-Fi password" to your home Wi-Fi
Press and hold the "function button".
Please enter your password.
"Beep" is heard three times
Please wait until it exceeds
Sai.
"Function button" flashes white
The connection is ready to change.
if,
You will hear a "beep" within 3 minutes
If you can't
"Function button" is white
If it does not blink, follow the same procedure again.
(Press the "function button") and try again
Please.
<2>
3 Connect your smartphone and robot
In the smartphone settings, Wi-F "
Search for "i MAMORU" and connect.
Once connected to Wi-Fi, close the screen, restart the "Huiba" app again, and finally press "Finish".
MAMORU-### is displayed.
* Notes on connecting the robot to your home Wi-Fi router
1) It supports IEEE802.11b / g and 11n frequency 2.4GHz.
2) It does not support IEEE802.11a and 11n 5GHz.
Four Robot and app settings completed
Launch the app. When you press "Huiba" at the bottom left of the application screen, the MAMORU icon is displayed in the center of the screen.
And the setting is completed.
<3>
Five Robot remote control
Press the "Huiba" icon in the app and press the MAMORU icon to control the robot's remote control.
Shift to real-time communication or real-time communication.
1 Communication with camera by voice
A dial tone is played from the smartphone and music is played from the robot to start communication.
2 Remote control operation
Enter the desired Wi-Fi, then enter the Wi-Fi encryption settings and password.
Wait for the robot to respond with a single "beep" that indicates the successful completion of the Wi-Fi configuration.
▶ Press the "Direction" button on the left side to move the robot forward, backward, left side and right side.
▶ Slide the cam in the empty area of the icon on the screen to ± 45 °.
Up or down in the range of
Adjust
▶ [Cleaning] Cleaning will start. Press it again to stop.
▶ [Charging] The main unit returns to the charging stand and starts charging.
▶ [Speed] You can switch the running speed between high speed and low speed.
▶ [Take a picture] You can take a picture.
▶ [Mute] Ends voice communication between the robot and smartphone.
You can change the cleaning mode by pressing the ▽ of the "Zigzag mode" icon on the upper left.
▶ [Zigzag mode] Cleans the room in a zigzag manner.
Press "Zigzag Mode" again to stop.
▶ [Spot mode] Set to automatic cleaning mode to clean the specified spot for 3 minutes.
Press "Spot Mode" again to stop.
▶ [Edge mode] Clean the edges of the room.
Press "Edge Mode" again to stop.
<Four>
6 Add family members
App to be added (or will be) to family members in advance
Download and register "Huiba"
Must be (free). The administrator opens "Members" as follows:
Press "+" on the upper right side and enter your mobile phone number or mobile phone
1
Select from the contacts registered in the story, and the target user is a robot
Be one of the family members of the administrator.
"Huiba"
* New users are apps
2
New users are apps
Open "Huiba" and at the bottom of the screen
Receive a request message to the "member".
"men
Press "Bar" and request "New Bill" at the top of the screen
Make sure there is sage and
Press "New Billing".
<Five>
Must be registered.
Press "Agree" to family
I will participate in.
Press "Reject" to family
Do not participate in.
3
After the new user agrees, the administrator will take the robot's
Press Con
[Robot settings]
Is it the "Robot Settings" page?
Et al.
"Robot Family Men
Manage the bar "
Choose.
"member"
MAMORU eye at the top of the page
Go to.
Upper right "add to" the button
New user added
Press to have one user
Is On the "Members" page
Add to family.
MAMORU icon is a table
Shown and family members
The additional settings are complete.
7 Cleaning reservation settings
You can reserve the cleaning time in "Member"-> "MAMORU"-> "Cleaning reservation settings".
<6>
8 Description of function buttons
"Member" → "MAMORU" →
Function button in "Explanation of function buttons"
Display the description of the tongue.
9 update
Go to "Members"-> "MAMORU"-> "Check for Updates"
Please update from time to time.
Contact
aspect
071-530
05 05 O 7 Customer 0 Talk window
Reception time 10:
00-17: 00 Monday-Friday (Excluding holidays)
We may be closed for the year-end and New Year holidays and other reasons.
Please note.
<7>