Rockwell Automation Canada
135 Dundas St
Cambridge, ON, N1R 5X1 Canada
Tel 888 672 0236 Fax 519 740 4163
TYPE TEST CERTIFICATE No. 1022
EQUIPMENT: High Voltage Soft Starter
MODEL 156X, X=0, 1, 2, 3
RATING
Rated Voltage Ue
Maximum normal current Ie
Overload current* Ic
Rated lightning impulse voltage Uimp
Rated power frequency voltage Ui
Rated frequency
Rated normal current bus
Rated short time withstand current bus***
Rated peak withstand current bus
Rated duration of short circuit bus
Rated duration of short circuit converter
Rated IAC arch flash classification
* ILRP prospective Locked Rotor Current
** for equipment 72” width or more
*** 1.2kA bus rating. Larger bus has higher rating see table.
Issued in conformity to ISO 17025
7.2kV
600A
6xIe/10s, 4.5xIe/30s
60kV
20kV
50/60Hz
1.2, 2, 3KA
50kA rms
130kA
0.5s
0.1s 1CO
AFLR 40kA//0.5s or 50kA/0.5s**
High Voltage Soft Starter is certified by the third party agency, Underwriters Laboratories per UL 347B standard. There are no
IEC product standards to directly cover High Voltage Soft Starter. However some IEC standards have applicable requirements to
High Voltage Soft Starter. UL 347 B test conditions are similar or more stringent than IEC standards. The IEC standards, their
applicability and the table summarizing the tests data are listed below:
IEC 62271-1 Common clauses for high-voltage switchgear and Controlgear, covers specific requirements
for high voltage equipment, dielectric strength, short circuit withstand
IEC 62271-106 High-Voltage alternating current contactors and contactor based starters, covers specific
requirements for high voltage controllers, insulation, short circuit, overcurrent. The main input controller
and bypass circuit are provided with an IEC approved contactor.
IEC 62271-200 AC metal-enclosed Switchgear and Controlgear for rated voltages above 1kV and up to
including 52kV, covers requirements for arc fault. IEEE C37.20.7 Guide of arcing was used in conjunction
to IEC 62271-200 set up.
IEC 60947-4-2 Low-voltage switchgear and controlgear - Part 4-2: Contactors and motor-starters - AC
semiconductor motor controllers and starters, covers specific functional requirements for power converter
section of soft starter: soft start/stop, duty cycle, overload operation.
UL 347B Outline of Investigation for Medium Voltage Controllers up to 15kV. Standard used by third party
Underwriters Laboratories for certification.
The test reports concern exclusively to the equipment tested. This Type Test Certificate is entirely based on
Type test Report as mentioned. The certificate shall not be reproduced without written approval of the
Rockwell Automation
Document Control Number: MVB1022-A-EN
Table 1 Test reports verifying ratings assigned by the manufacturer
Performances
Construction requirements
Enclosure, grounding, spacing,
flammability, corrosion
Dielectric test
power test 20k/1min,
impulse 60kV/1.2µs/50µs
Temperature rise test
Ie 600A
Short time and peak withstand bus ,
(2kA) 62kA/10cycles, 60kA/4s
Short time and peak withstand bus ,
(1.2-3kA) 50kA/0.5s
Short-circuit withstand Class E2
3CO /40kA/7.2kV/ 48X fuse
Overload current withstand
3.6kA/10s, 2.7kA/30s
Short time and peak withstand
current test power converter 1CO,
31.5kA/0.1s
Arc test
IAC: AFLR/40kA/0.5s
18”, 26”, 36” width units
Arc test
IAC AFLR/50kA/0.5s
72” width units
Test According to
Standard/Clause
IEC60947-4-2/8.1
UL347B/7,10
IEC 62271-1/6.2
IEC 6671-106/6.2,
UL347B/32, 38
IEC62271-1/6.5
IEC62271-106/6.5
IEC60947-4-2/9.3.3.3
UL 347B/25
IEC62271-106/6.6
IEEE C37.23
UL347B/36.1, 37
IEC62271-106/6.6
IEEE C37.23
UL347B/36.1, 37
IEC62271-106/6.104
IEC60947-4-2/9.3.4
UL347B/33
IEC60947-4-2/9.3.3.6.2
IEC62271-106/6.103
UL 347B/29
IEC 60947-4-2/9.3.4
IEC 62271-1/6.6.2
UL347B/33
IEC 62271-200/8.104.5
IEEE C37.20.7,Type 2
IEC 62271-200/8.104.5
IEEE C37.20.7,Type 2
Test Reports
No.
ER093-2005
to
ER099-2005
ER-077-2005
ER-088-2010
Date
08/03/2005
Issued by
Rockwell
Automation
06/09/2010
Rockwell
Automation
ER-077-2005
ER-088-2010
ER-039-2010
ER-125-2010
15368-B-26
17550-A-26
03/15/2010
09/10/2010
Rockwell
Automation
11/25/2004
08/23/2007
Powertech BC
K-14024A
K-13079B
K-12289B
02/07/2014
03/26/2013
11/28/2012
KEMA
15368-B26
11/25/2004
Powertech
ER-077-2005
ER-088-2010
06/09/2010
Rockwell
Automation
ER-137-2011
11/17/2011
Rockwell
Automation
17550-B-26
15368-A-26
15599A-26
15317-26
14224-B
ER104-2014
ER106-2014
08/24/2007
11/24/2004
08/24/2005
10/20/2004
10/03/2014
11/27/2014
01/28/2015
Powertech
KEMA
Rockwell
Automation
The equipment has been manufactured in Canada by Rockwell Automation
Signed..
Date… June 15, 2016
Iulian Profir Sr. Project Engineer - Product Certification Engineering
The test reports concern exclusively to the equipment tested. This Type Test Certificate is entirely based on
Type test Report as mentioned. The certificate shall not be reproduced without written approval of the
Rockwell Automation
Document Control Number: MVB1022-A-EN