GoldSpec™ Single Phase DC Motor Speed Controls Your economical solution for speed control MOTOR SPEED CONTROLS GS60U GS10 GS23001C GS600 GS4 GS23101C Features and Benefits • Dual voltage 115/230 VAC single phase input, 90/180 VDC output, form factor 1.37 controls to run SCR brush type permanent magnet or shunt wound DC motors • Compact industry standard MM footprint for chassis controls • 1% speed regulation over a 60:1 speed range. 50:1 speed range for regenerative chassis control) • User adjustable calibration pots for IR compensation, min speed, max speed, torque, acceleration and deceleration GoldSpec™ single phase DC Motor Speed Control series and accessories are a reliable and economical solution for variable speed control of permanent magnet or shunt wound brush type DC motors from 1/8 to 2 HP. Each GoldSpec™ DC Motor Speed Control series has unique benefits to cover your speed control needs. The GS23000C series uses SCRs to provide full-wave rectification of the AC line input. A unique feature of the GS60U is the ability to choose the enable and inhibit terminals to operate either “normally open” or “normally closed.” With excellent control and plastic NEMA 4X enclosure, the GS10 series is the perfect solution for many applications that require an enclosed drive. • Easy to use spade terminals on chassis controls; screw terminals on enclosed controls * For Quick Start Guides, dimensions and user manuals see www.applied.com/gsmum Applied Industrial Technologies. Keeping you InSync® with economical, reliable speed control options. Authorized Distributor: Products of: GoldSpec™ Single Phase DC Motor Speed Controls and Accessories SCR DC Controls Ratings 115 VAC Input Description (Agency Approvals) 230 VAC Input Model HP Amps HP Amps Chassis Control (UL/CuL/CE) GS23001C ½* 5* 1* 5* NEMA 1 Control (UL/CuL/CE) GS23101C ½* 5* 1* 5* NEMA 1 Control – Reversing (UL/CuL/CE) GS23201C ½* 5* 1* 5* NEMA 4X Control (UL/CuL) GS10 1 10 2 10 NEMA 4X Control – Reversing (UL/CuL) GS10-R 1 10 2 10 Chassis Regenerative Reversing Control (UL/CuL) GS60U ½* 5* 1* 5* *Ratings double with addition of optional heat sink (see below) Accessories Description (Agency Approvals) Model Signal Isolator (UL/CSA/CE) GS4 Digital Closed Loop Controller (UL/CE) GS600 Use With All Controls All Controls Plus Feedback Device • 5VDC or 12VDC NPN-Type Encoder • 5VDC or 12VDC NPN-type Proximity Switch • Hall Effect Sensor • Magnetic Pickup Heat Sink GS223-0159 GS23001C & GS60U GS223-0174 GS23101C & GS23201C 10k Potentiometer** GS202-0031 All Controls Inhibit Plug - 18” Leads GS201-0024 GS201-0079 GS23001C, GS23101C, & GS10, GS10-R Inhibit Plug – 36” Leads ** Potentiometer is included with all controls – use this for additional potentiometer requirements or as a replacement Contact Your Local Applied® Service Center Authorized Distributor: 1-877-279-2799 WARNING: Injury, death, property damage, and/or equipment failure may result from the misuse or misapplication of the products featured in this publication. The information in this publication is provided “AS IS,” WITHOUT any WARRANTY OF THE INFORMATION’S ACCURACY OR THE PRODUCTS’ SUITABILITY FOR ANY PARTICULAR USE. © 2009 Applied Industrial Technologies, Inc. All Rights Reserved. IN-0609-09-5444 GoldSpec™ is a registered trademark of Applied Industrial Technologies. Corporate Headquarters 1 Applied Plaza Cleveland, Ohio 44115 Toll Free Phone: 1-877-279-2799 Applied.com