GENUINE PARTS
INSTALLATION INSTRUCTIONS
1.
2.
3.
DESCRIPTION:
APPLICATION:
PART NUMBER:
KIT CONTENTS:
4.
Item
A
B
Qty.
1
1
Extreme Custom Grille
Cube
F2310-1FC0A
Description
Extreme Custom Grille
Installation Instructions
Part Number
-----
A
5.
TOOLS REQUIRED:
● Clip remover
B
● Needle nose pliers
6.
PRE-INSTALLATION CAUTIONS/NOTES:
7.
INSTALLATION PROCEDURE:
Fig. 1
1.
● Masking tape
Installation preparation
a)
Open vehicle engine hood.
b)
Apply masking tape to the front bumper, around
the original grille, to prevent scratches. See Fig. 1.
Apply masking tape
to the front bumper
Page 1 of 4
F2310 1FC0A II 08/12/16
INSTALLATION INSTRUCTIONS - Extreme Custom Grille
Push pin A
(reuse)
Fig. 2
c)
Use a clip remover to remove push pins A(reuse).
See Fig. 2.
Fig. 3
d)
Using needle nose pliers, squeeze clips B on the
back side of the original grille and pull forward on
the top portion of the original grille to disengage
the clips B from the vehicle. See Fig. 3.
e)
Use a clip remover to remove push pins C(reuse).
See Fig. 4.
Pull forward
Original
grille
Squeeze
Clip B
Push pin C
(reuse)
Fig. 4
NOTE:
DO NOT MIX PUSH PINS A AND C..
Fig. 5
f)
Page 2 of 4
By hand, unhook the original grille claws from the
front bumper and slowly remove the grille by
pulling the grille away from front bumper. See Fig
5.
F2310 1FC0A II 08/12/16
INSTALLATION INSTRUCTIONS - Extreme Custom Grille
Fig. 6
Original grille
Squeeze with needle nose
pliers
Rotate
counter
clockwise
about 45
degrees
Clip B (reuse)
Rotate
clockwise
about 45
degrees
g)
Using needle nose pliers, squeeze the top and
bottom of clips B(reuse) on the back side of the
original grille. See Fig. 6.
h)
While squeezing clips B（reuse), rotate about
45 degrees and pull to remove clips B(reuse)
from the original grille. See Fig. 6.
● If clips B are broken during removal, please order
service part number 76882-WD400 for replacement.
Squeeze with needle nose
pliers
Extreme custom grille
Fig. 7
Squeeze with needle nose
pliers
Rotate
clockwise
about 45
degrees
Clip B (reuse)
Rotate counter
clockwise about 45
degrees
Squeeze with needle nose
pliers
Push pin C
(reuse)
Headlamp
Fig. 8
2.
Extreme custom grille installation
a) Using needle nose pliers, align clips B(reuse) to the
Extreme custom grille and rotate until clips
B(reuse) are completely installed. See Fig. 7.
● Rotate clips B until "click" sound is heard. "Click"
sound indicates that the clips are completely
installed.
NOTE:
WHEN INSTALLED CORRECTLY THE CLIP TABS
SHOULD BE FACING INBOARD.
b)
Install push pins C(reuse). See Fig. 8
Front bumper
Page 3 of 4
F2310 1FC0A II 08/12/16
INSTALLATION INSTRUCTIONS - Extreme Custom Grille
：Clip B (reuse)
Fig. 9
c)
：Claw
Align the Extreme custom grille clips B and claws to
the holes in the front bumper and push the
Extreme custom grille against the front bumper to
insert the clips B and claws in the holes. See Fig.
9.
● Push the Extreme custom grille against the front
bumper until "click" sound is heard. "Click" sound
indicates that the Extreme custom grille is completely
installed.
Push pin A
(reuse)
Fig. 10
d)
e)
Page 4 of 4
Install push pin A(reuse). See Fig. 10
Remove the masking tape from the bumper and
close the vehicle engine hood.
F2310 1FC0A II 08/12/16