EGGER Compact Laminate Collection
advertisement
Egger Compact Laminate Collection A durable and design focused solution for interiors. CONTENTS 03 EGGER Compact Laminate 14 Product overview 16Textures 18 Uni colours 18 Neutral uni colours 21 Natural uni colours 22 Intensive uni colours 24 Woodgrain reproductions 24 Classic & modern 30Artwood 31Authentic 34Exotic 36 Material reproductions 36 Stone & mineral 37 Textile & leather 38 Used Look 39Metal 40 Texture meets colour 41 Processing instructions 41 Storage 42Processing 44Fabrication 48Application 59 Technical data 60 Cleaning & maintenance 60 Waste treatment 61Service 62 Availability guide – Full product overview EGGER Compact Laminate 3 EGGER COMPACT LAMINATE: ELEGANT AND ROBUST The appeal of Egger Compact Laminate is not just down to the attractive designs and textures. Its durability and moisture resistance open up a new range of interior design opportunities. Compact Laminate is particularly suitable for interior applications subjected to high stress, as well as areas where there may be an extra requirement for hygiene standards, such as in restaurants, or hospitals. It is also used in wet areas, such as in bathrooms, sanitary facilities, and changing rooms. It is the combination of durability and sleek design that makes Compact Laminate so interesting for a variety of solutions within the commercial interiors market. Characteristics • Sleek and elegant design • Hard-wearing and impact resistant surface • No edge or surface finish required • Homogeneous material for precise processing • Very high stability • Moisture resistant • Hygienic and easy to maintain • Resistant to common cleaning products and chemicals www.egger.com/compactlaminate 4 EGGER Compact Laminate HIGH PERFORMANCE WITH DESIGN FLEXIBILITY As well as being easy to clean and maintain, compact laminate has long term durability and robustness making it the go to product for many design projects. EGGER Compact Laminate is ideal for wet areas or high stress areas such as tables, worktops, wall panelling, changing rooms and partitions. This product will help you bring unique designs into rooms where it was not possible before. talsee.ch EGGER Compact Laminate 5 USE FRENCH IMAGE W1000 ST9 Premium White, U337 ST9 Fuchsia 6 EGGER Compact Laminate The surface of EGGER Compact Laminate can be routered to create tailored designs. F425 ST10 Beige Linen EGGER Compact Laminate 7 DESIGNED TO THE CORE The homogeneous core of EGGER Compact Laminate is ideally suited to precision processing, opening up the possibilities for bespoke design. The board can be milled, routered, grooved as well as drilled - there are few limits. Any part of the board can be milled or routered, given no additional edge finishing process is neccessary. Not only is it possible to specify the surface finish, but selecting a black or a white core can give your furniture a completely different look. 8 EGGER Compact Laminate Sleekness and durability - one does not exclude the other. SLEEK AND CONTEMPORARY Combining both strength and a slimline material means areas where a thicker materials may have been required can now be elegant thin designs. Not only can this be done in a solid colour but also with authentic woodgrain and alternatives to metals. EGGER Compact Laminate 9 TAKE ADVANTAGE OF A VERSATILE PRODUCT EGGER Compact Laminate is great for any creative design idea thanks to its properties and processing possibilities in particular. Break new ground with your furniture, such as this stool, that became an innovative furniture item. Using pieces of EGGER Compact Laminate and having the core as a feature, creates a durable design led piece. W1200 ST2 Porcelain Discover the uni colours, woodgrain and material reproductions of the Zoom Collection at www.egger.com/zoom. Picture: Photographic workshop Katharina Jäger 10 EGGER Compact Laminate SYNCHRONISED PORE COMPACT LAMINATE EGGER is the first in the world to offer synchronised pore decors on a compact laminate. The Feelwood decors use the latest technology to align grain pattern with the surface texture of the board. These woodgrain decors take a step closer to appearing like a real wood and create an even more authentic finish. The Feelwood range can offer benefits which are not available when using real wood. Panels can be replaced without the fear they will not match with the remaining furniture or panelling and there is also a higher resistance and durability. EGGER Compact Laminate 11 © Nicolas Tarantino A SOLUTION FOR ALL PROJECTS ST27 is a classical yet modern design. The soft planking and texture of the Tortona decor gives an authentic appearance. ST28 is a rustic decor, the knots and planking of Synchronised pore decors are also the Gladstone decors create a natural feel which is available in Laminate and melamine highlighted by the sandblasted decors. faces panels. Discover the latest decors at ST29 is ideal for large surfaces as the dramatic grain www.egger.com/zoom pattern gives a sophisticated and elegant finish. 12 EGGER Compact Laminate STAY CO-ORDINATED Compact laminate is part of our matching decor and texture range. This allows you to combine a variety of EGGER products within a design: Decors available as compact laminates can also be supplied as melamine faced boards, lightweight boards, laminates and edging. Please see our online availability guide at www.egger.com/downloads. Let your ideas take shape with our VDS software. The Virtual Design Studio offers you an almost unlimited variety in terms of design and visualization of your projects. Place the EGGER standard decors into more than 80 room sets and visualise your own ideas. www.egger.com/vds EGGER Compact Laminate 13 The EGGER range of matching decors and textures allows you to mix and match decors and materials from of the Zoom collection. H1277 ST9 Lakeland Acacia, U330 ST9 Aubergine 14 EGGER Compact Laminate PRODUCT OVERVIEW EGGER Compact Laminate is available with a black or white core. It is produced using multiple layers of phenolic resin impregnated core papers and melamine resin impregnated decor papers. The layers are fused together under high pressure and temperature. Due to its construction compact laminate is ideal for high traffic areas. EGGER Compact Laminate performs to EN 438 and is used for many applications such as wall panelling, cubicles, partitions, kitchen worktops and offices as well as other high traffic areas such as hotel rooms and retail spaces. A flame retardant range is also available. EGGER Compact Laminate Flammex Euroclass B is classified as B-s2, d0 and conforms to EN 13501-1. Flammex is used in areas where there is an increased requirement for fire protection such as airports or hospitals. EGGER Compact Laminate 15 COMPOSITION OF A COMPACT LAMINATE 1 2 3 4 1 Overlay (optional) 1) 2 Decorative impregnated paper 3 Sodium kraft papers 4 Decorative impregnated paper 5 Overlay (optional) 1) 5 1) Compact laminates with printed decors (wood and material reproductions) are enhanced with overlay. PRODUCT OVERVIEW AND CLASSIFICATION Within the EN 438 Standard, compact laminates are differentiated and classified by three letters – also referred to as the classification system. The following gives an overview of the material types offered by EGGER as standard. Size 2790 × 2060 mm (alternatives 5600 × 2060 mm) Thickness 3, 4, 5, 6, 8, 10, 12 and 13 mm Core colour Black or white Material type A wid e rang e availa ble fro m 2 boar ds Standard decors: CGS(Black core standard grade) Standard decors: CGF (Flame retardant grade) Standard decors: BCS (White core standard grade) Pearlescent decors: ACS (Black core standard grade) Pearlescent decors: ACF (Flame retardant grade) AVAILABILITY Details relating to the complete matching products availability guide can be found from page 61, or visit: www.egger.com/zoom Eurodekor melamine faced chipboard Laminate Door Size Laminates Compact laminates interior ABS Edging 16 EGGER Compact Laminate TEXTURE INNOVATION With ZOOM every decor uses the most appropriate surface texture, ensuring that our decorative materials both look and feel like the real thing. NEW Synchronised pore ST27 FEELWOOD Elegance – The fine and linear, yet natural texture is synchronised with the grain of the Tortona decor to create an incredibly realistic finish. NEW Synchronised pore ST28 FEELWOOD Nature – This texture is characterised by its authentic feel. The synchronised knots and planking create a natural feel reminiscent of solid wood. NEW Synchronised pore ST29 FEELWOOD Ambiance – The synchronised texture has a striking yet elegant appearance. It is ideal for large applications to create a tasteful, sophisticated feel. It traces the grain with soft recesses, creating a tactile effect. NEW ST87 Ceramic – The matt-gloss effect simulate the surface and feel of a ceramic plate helping to create visual depth. EGGER Compact Laminate 17 ST9 Perfect Matt – Used with uni colours and woodgrains to offer a soft, natural feel. This texture is ideal for the current trend for matt surfaces. ST10 Authentic – A highly authentic and realistic surface texture for natural, distinctive and rustic decors. The perfect surface for solid wood reproductions. ST15 Office – A smooth flat surface finish with low gloss levels and low maintenance. Combines with intensive uni colours and a wide variety of woodgrains. ST22 Matex – Thanks to its feel and matt gloss effect, it give linear and lively woodgrain decors more naturalness and depth for a more realistic wood-like finish. ST18 Waveline * – The horizontal surface texture offers new levels of depth, has a modern appearance and is reminiscent of solid wood which has been routed out and then painted or lacquered. * from 8 mm and identical surface texture on both sides ST2 Diamond – Has a grainy, mini-pearl texture, with a medium gloss level. This surface is robust, very durable and used with solid colours and pearlescent decors. 18 EGGER Compact Laminate NEUTRAL UNI COLOURS Basic colours in white, beige, brown, grey and black tones - timeless, universal and flexible. W1000 ST2 Premium White ST9 Premium White ST18 Premium White ST22 Premium White W1200ST2 Porcelain ST9Porcelain W980 ST2 Platinum White ST15 Platinum White W908 ST2 Basic White W911 ST2 Cream White ST15 Cream White U224 ST15Silk U216 ST15Oyster U222 ST15Crema U104 ST15Alabaster U108 ST15Vanilla U113 ST15Cotton NEW U702ST9Cashmere U750 ST9 Taupe Grey U775 ST15 White Grey U708 ST15 Light Grey U763 ST15 Pearl Grey ST18 Pearl Grey U765 ST15 Silver Grey U732 ST15 Dust Grey U963 ST15 Diamond Grey U156 ST9 Sand Beige U727 ST9 Stone Grey ST22 Stone Grey U206ST9 Malaga U808ST9 Mocha U803 ST15 Black Brown U795 ST9 Brown Grey U748ST9 Truffle NEW U631ST9Olive U730ST9Basalt U741ST9Lava ST22Lava U961ST2Graphite U999ST2 Black ST18Black Neutral uni colours for a calming and modern atmosphere EGGER Compact Laminate Laminate 21 21 NATURAL UNI COLOURS A selection of pastels and chalk colours, ideal for combinations thanks to their subtle tone and soft, matt appearance. U107 ST9 Velvet Yellow U204ST9 Camel U334ST9 Powder NEW U343ST9 Vino U807ST9 Nougat U617ST9Wasabi U635ST9Moss U701ST9Platinum U518 ST9 Ice Blue U539 ST9 Steel Blue U336ST9 Orchid U337ST9Fuchsia U330ST9 Aubergine 22 EGGER Compact Laminate INTENSIVE Bright, eye-catching primary colours with a strong, bold appearance. U129 ST15 Sun Yellow U143 ST15 Signal Yellow U146 ST15 Maize Yellow U114 ST15Yellow U634 ST15 Velvet Green U625 ST15 Apple Green U630 ST15 Lime Green U632 ST15 Grass Green U628 ST15Green U535 ST15Aqua U536 ST15Lagoon U633 ST15Turquoise U538 ST15Ocean U533 ST15 Polar Blue U522 ST15Horizon U537 ST15 Brilliant Blue U514 ST15 Baltic Blue U525 ST15Blue U506 ST15Marine U329 ST15Manderine U332 ST15Orange U328 ST15Lipstick U321 ST15Red U323 ST15 Chilli Red U311 ST15Burgundy 24 EGGER Compact Laminate CLASSIC & MODERN A mix of our best selling classic woodgrains and newer modern alternatives. H3758 ST9 Helsinki Birch H1867 ST9 Cream Canadian Maple H1733 ST9 Mainau Birch EGGER Compact Laminate 25 H1521ST15Maple H1887 ST9 Natural Starnberg Maple H3911 ST9 Natural Tauern Beech H1518 Natural Beech H1582 ST15 Ellmau Beech H1511 ST15 Bavarian Beech Natural Tyrolean Beech H3662 ST9 Natural Venetian Cherry H1615 ST9 Romana Cherry ST15 H1920 ST9 26 EGGER Compact Laminate H1706ST15 Cherry H1502ST15 Alder H3113 Lindau Pearwood H1950 ST15 Natural Calvados Natural Dijon Walnut H3775 ST9 Light Tennessee Walnut ST15 H3734 ST9 H1951 ST15 H3704 ST15 Sienna Calvados Tobacco Aida Walnut EGGER Compact Laminate 27 NEW NEW Synchronised pore Synchronised pore H3760 ST29 White Cape Elm Also available as ST9 H3766 H3755 ST22 H1484 ST22 Brown Grey Avola H1476 ST22 Champagne Avola H1424 ST22 Woodline cream H1428 ST22 Woodline mocha H1474 White Swiss Larch ST22 White Avola ST29 Dark Brown Cape Elm Also available as ST9 H1277 ST9 Light Lakeland Acacia 28 EGGER Compact Laminate H3304 ST9 Grey Lacquered Chateau Oak H3306 ST9 Anthracite Chateau Oak H3363 ST9 Anthracite Highland Oak H1334 ST9 Light Ferrara Oak NEW Synchronised pore H1793 ST27 Lava Tortona Also available as ST9 Modern classics for a homely atmosphere. NEW Synchronised pore H1796 ST27 Natural Tortona Also available as ST9 H1298 ST22 Sand Lyon Ash H3778 ST9 H3400 ST22 Rustic Pine H1487 ST22 Bramberg Pine H1215 H3128 ST15 ST22 Brown Cassino Ash Natural Caribbean Walnut Natural Plum H3129 ST9 Autumn Plum 30 EGGER Compact Laminate ARTWOOD Influenced by real wood, but given an exciting new interpretation by changing the grain pattern. H3078 ST22 F584 Hacienda White ST22 Fino cinnamon H3081 ST22 Hacienda Black F583 ST22 Fino Bronze EGGER Compact Laminate Laminate 31 31 AUTHENTICS A new generation of woodgrains in natural colour tones with knots, cracks and a strong, authentic character. H1146 ST10 Grey Bardolino Oak H1372 H1145 ST10 Natural Bardolino Oak H3303 ST10 ST22 Natural Aragon Oak Natural Arlington Oak H3331 ST10 H3332 ST10 Natural Nebraska Oak Grey Nebraska Oak NEW Synchronised pore H3309 ST28 Sand Gladstone Oak Also available as ST9 NEW NEW Synchronised pore H3326 ST28 Grey Beige Gladstone Oak Also available as ST9 Synchronised pore H3325 ST28 Tobacco Gladstone Oak Also available as ST9 EGGER Compact Laminate 33 H1150 ST10 Grey Authentic Oak H3753 ST22 Country Montana Larch H1151ST10 Brown Authentic Oak H3700ST10 Natural Pacific Walnut Furniture with visible cracks and knots create an authentic atmosphere. H3114 ST9 Tirano Pearwood 34 EGGER Compact Laminate EXOTICS Eye-catching woodgrains with a distinctive, individual character. H3012 ST22 Coco Bolo H3006 ST22 Sand Zebrano H3005 ST22 Grey Beige Zebrano H3082ST22 Amazonas FOR VISUALISATION PURPOSES The small images give you a close-up view of the decor surfaces. They correspond to a section of 900 x 600 mm. H3031 ST9 Dark Cordoba Olive H3090ST22 Driftwood H3025ST15 Macassar H3058 ST22 Mali Wenge 36 EGGER Compact Laminate STONE & MINERAL Authentic reproductions of man-made, natural stone & minerals. F396 F210 ST10 ST9 Basaltino Grey White Amalvi Marble F236 F211 ST15 Terrano Grey ST9 Brown Amalvi Marble F276 ST9 Arkosa Sand F274 ST9 Light Concrete F275 ST9 Dark Concrete EGGER Compact Laminate 37 TEXTILE & LEATHER Soft, natural materials and designs which appear like the real thing. F428 ST10 Brown Leather F425 ST10 Beige Linen F426 ST10 Grey Linen 38 EGGER Compact Laminate USED LOOK Materials with signs of use and weathering help to create a vintage look. Although pure and linear designs remain a key trend, the use of materials which show character and imperfection are increasing being demanded. F636 ST15 F633 Titanium Blue Metallo ST15 Grey Brown Metallo NEW F310 ST87 Rust Ceramic NEW F311 ST87 Anthracite Ceramic EGGER Compact Laminate Laminate 39 39 METALS Warm and cool interpretations of metal, each with a high quality, pearlescent surface finish. F501 ST2Titanium F784 ST2 Stainless Steel Microline F509ST2Aluminium F447 ST2 Quartz Lava 40 EGGER Compact Laminate TEXTURE MEETS COLOUR Deep textures or matt gloss effect are applied to solid colours to give exciting fantasy patterns. W1000 ST18 Premium White W1000 ST18 Premium White U763 Pearl grey ST18 U999 ST18Black W1000 ST22 U727 W1000 ST22 Premium White Premium White ST22 Stone Grey U741 ST22Lava EGGER Compact Laminate EGGER Compact Laminate 41 e 41 PROCESSING INSTRUCTIONS 1. STORAGE EGGER compact laminate must be stored in enclosed, dry areas at approximately 18°C to 25°C and a relative humidity of approximately 50% to 65%. After removal of the original packaging, the compact laminate should be stored stacked horizontally on a sturdy, flat and level base board of equal or greater dimension. Direct floor contact and/or exposure to sunlight must be avoided at all times. The top board should be covered with a laminated protective board (not raw chipboard) of at least equal or greater dimension (see Figure 1). Where horizontal storage is not possible, the compact laminate sheets should be stored at an angle of approximately 80°, in an inclined rack, providing support to the surface area and ends (see Fig.2). A laminated protective cover board of at least equal dimension is also required for vertical storage. Figure 1 Right Wrong Figure 2 Incorrect storage can result in permanent distortion of the board. 42 EGGER Compact Laminate 1.1. Handling After removing the packaging and prior to processing, the compact laminates should be inspected for visible damage. In view of the relatively heavy weight, special care is required when transporting and handling compact laminates. As a rule, all persons transporting and/or handling compact laminates should wear personal safety equipment such as gloves, safety footwear and suitable work wear. The sheets have to be lifted up; pushing or dragging the decorative sides over one another should be avoided (see Figure 3). Figure 3 1.2. Conditioning Compact laminates react to changes in ambient conditions with a certain amount of dimensional movement. For this reason, the storage and processing conditions should correspond as closely as possible to the prevailing conditions where the material will be subsequently used. Prior to installation, compact laminate elements should be conditioned for an adequate period of time at the installation location under the conditions of subsequent use. Compliance with the storage recommendations is also necessary on construction sites. 2. PROCESSING Due to the high density and resulting high cutting forces, the processing of compact laminate, compared to other wood-based materials, leads to higher tool wear. The use of blunt or unsuitable tools can lead to inadequate machining and result in the release of obnoxious odours. Tungsten carbide tools are mainly used. Diamond-tipped tools are recommended for processing large quantities and automated processing centres. Ensure that the tool blades are maintained in good condition in order to obtain satisfactory results. To ensure efficient and economical fabrication, especially prior to processing a large production batch or implementing challenging projects, it is advisable to consult manufacturers on the most appropriate tool selection. 2.1. Extraction Compliance with all safety standards and regulations, applicable to the wood processing industry in terms of dust extraction, fire prevention etc., is essential when processing compact laminates. Where adequate extraction is not provided, respiratory protection must be worn. The processing of compact laminates is not critical, however, a small number of people experience an allergic reaction to any kind of dust. EGGER Compact Laminate 43 plovitzahn hohle Zahnbrust Duplovitzahn hohl Dach-Duplovitzahn Flachzahn 2.2. Cutting Panel or circular bench saws are recommended for cutting compact laminates to size. A good cutting result depends on a variety of factors, such as correct saw blade projection, feed rate, tooth shape, tooth pitch, rotational and cutting speeds. Suitable tooth shapes are alternate and hollow tooth, whilst the trapezoidal flat tooth has proved to deliver longer tool life with consistently Hollow tooth Duplovitzahn mit plovitzahn mit good Fase cutting quality (see Figure 4). Trapez-Flachzahn Wechselzahn Trapezoidal flat toothDuplovitzahn Alternate tooth hohle Zahnbrust Flachzahn Figure 4 A very good cutting quality on both sides is achieved with the use of a scoring saw. The quality of the cut edge can be affected by adjusting the height of the saw blade. A saw entry angle of 45° is optimal. This is achieved when 10 percent of the saw blade diameter protrudes over the work piece. • Cut on face side not clean → Set the saw blade higher • Cut on the underside not clean → Set the saw blade lower Alternatively, the cut on the underside can be improved by placing a base board of plywood, hardboard or similar underneath the compact laminate sheet. 2.3. Machining Wechselzahn Duplovitzahn mit Fase Diamond-tipped tools are recommended for machining compact laminate. The suitability of carbide-tipped tools is limited. Tools with segmented blades should not be used, as the overcut in the overlap zone usually remains visible. To ensure a good edge quality, adding a processing allowance when cutting blanks is recommended, which, however, depends on subsequent edge processing. Because of the high cutting pressure, secure work piece and tool control is of particular importance. Numerous edge profiling options are available (see Figure 5). Figure 5 Any cutter marks can be removed by sanding and an even edge colour can be achieved by applying a silicone-free oil. Sharp corners and edges should be rounded to eliminate the risk of injury. 44 EGGER Compact Laminate 2.4. Drilling Drill bits designed for plastic sheet materials, with a point angle between 60° and 80°, are the best choice for drilling compact laminates (see Figure 6). The cutting speed and feed rate depend on the material of the chosen drill bit – HSS, HM, DIA. Please observe the specifications of the tool manufacturer. Spiral bits for drilling metal or wood can also be used, but the rotation speed and speed rate must be reduced in this case. Source: Company LEUCO, Mosquito through-hole bit Figure 6 For through holes, the compact laminate should be resting on a solid base which can be drilled into. Before the drill bit breaks through, the feed rate should be reduced in order to avoid break-outs on the exit side. For drill holes that do not go through, so-called blind holes, the minimum board thickness that must remain is 1.5mm. For drill holes parallel to the board surface, the minimum board thickness that must remain on either side of the drill hole is 3mm (see Figure 7). Figure 7 Cutting, milling, profiling and drilling tools should always be selected in consultation with the tool manufacturers. 3. FABRICATION Despite the good dimensional stability of compact laminate, changes in the ambient conditions can result in dimensional movement. The orientation of the cellulose fibres in the sodium kraft paper used, gives the compact laminate a production or machine direction (see Figure 8). Dimensional movement along the length is approximately half as great as it is across the width. The production direction of compact laminates with a decorative finish on both sides can only be determined by the production dimensions. It cannot be identified on compact laminate that has been cut to size. Woodgrains and directionally printed decors constitute an exception. Figure 8 When working with cut-size panels, it is important to ensure that the production direction is always matched up during installation. In view of the risk of confusion with cut-size panels, the production direction should be marked on board remnants. During fabrication and installation, the dimensional movement of the material must be taken into account from the outset. As a general rule, an expansion allowance of 2.0 mm/m should be provided. EGGER Compact Laminate 45 3.1. Cut-outs Cut-outs and apertures, for example for switches, ventilator grills or access openings, always have to be rounded, since sharp corners can lead to the formation of cracks (see Figure 9). Internal corners should be cut with an inner radius of at least 3 mm. All edges must be smooth, free of cracks and notches. Grooves and rebates also have to be rounded in order to avoid notch cracks. Cut-outs can be made directly with a router or pre-drilled with an appropriate radius and then sawn out from drill hole to drill hole. Adequate expansion gaps must be allowed for integrated components. Right! Wrong! Figure 9 3.2. Fixings Through holes must have sufficient clearance to compensate for the dimensional movement resulting from temperature and humidity fluctuations (see Figure 10). The diameter of the drill hole should be 2 – 3 mm larger than the diameter of the fixing device in order to avoid cracking. Countersunk screws should not be used (see Figure 11). If countersunk screws cannot be avoided, it is essential to use countersunk cup washers. Right! Wrong! Figure 10 Figure 11 Cutting screw threads in compact laminate is straightforward and self-tapping screws can also be used without a problem. Screws with a slow thread are recommended as they achieve a better pull-out resistance. Pre-drilling is essential in all cases. Metal and chipboard screws are suitable for screw connections parallel to the board surface. Screws must penetrate to a minimum depth of 25 mm and the diameter of the drill hole must be selected appropriately to prevent splitting. 46 EGGER Compact Laminate 3.3. Jointing Joints between compact laminate elements, capable of withstanding higher stresses, can be achieved with a combination of gluing and fixing devices, splines or biscuits (e.g. made of compact laminate), or grooves. Notes on bonding can be found under point 3.4. Bonding. When joining compact laminates, care should be taken at all times to ensure that connecting panels always follow the same production direction. Figures 12 to 16 below illustrate some possibilities for creating sturdy compact laminate joints. Grooved Grooved/rebated Splined Figure 12 Figure 13 Figure 14 Angled spline Metal profile, screw-fixed Figure 15 Figure 16 3.4. Bonding When bonding together two compact laminates, it is important to ensure that dimensional movements are not obstructed. To avoid stress, only adequately conditioned compact laminates should be bonded together and always only in the same machine direction. Bonding large surface areas should be avoided and the required application solutions and/or visual effects should be realised by a partial build-up of the required section (see 5.5 False edge). Joints that are subjected to heavy stress, for example due to vibrations, impacts or similar, should be reinforced with mechanical connecting elements. Examples of possible corner designs can be found under 3.3 Jointing. Prior to bonding, the boards have to be prepared by sanding, removal of dust, grease and contamination and pre-treated as necessary. EGGER Compact Laminate 47 Suitable types of glue for bonding EGGER compact laminates include: Glue type Jowat® 2K SE-Polymer 690.00 Glue type MBE Panel-loc Glue type OTTOCOLL® P 85, OTTOCOLL® M500 Jowat AG Ernst-Hilker-Straße 10 - 14 D-32758 Detmold t +49 (0) 5231 749-0 info@jowat.de www.jowat.de Moderne Befestigungs Elemente GmbH Siemensstr. 1 D-58706 Menden Hermann Otto GmbH Krankenhausstraße 14 D-83413 Fridolfing t 0 86 84-908-0 info@otto-chemie.de www.otto-chemie.de t +49 (2373) 17430-0 info@mbe-gmbh.de www.mbe-gmbh.de Compact laminate can not only be partially bonded to compact laminate, but also to solid wood or wood-based materials such as chipboard, MDF or multiplex board. For the concealed mounting of compact laminate elements to a substructure (see section 4.1 Wall panelling), we recommend, for example, Panel-loc by MBE. Conducting your own tests is recommended. Observing the processing instructions of the glue manufacturers is essential. 3.5. False edge Visually thicker boards can be achieved with built-up edges or by adding downturns or upstands. For built-up edges (Figure 17), compact laminate strips as required are glued along the edge – once again, the same machine direction has to be observed. The tension-equalising single-component Ottocoll® M500 adhesive by Otto Chemie is, for example, a suitable product. Built-up edge Downturn Figure 17 Figure 18 For thicknesses up to 100 mm or if the decor has to be visible on the edge for aesthetic reasons, a downturn or upstand (Figure 18) is a possible solution. First, the two components to be connected together are mitred at 45 degrees. Then the work piece is placed on a level surface, face side down, so that the tips of the mitres are touching and adhesive tape is applied over this joint. Then, both work pieces have to be turned over carefully. Now, glue is applied (Figure 19) and the shorter work piece or upstand is then folded over and pressed home (Figure 20). The upstand has to be secured in the correct position with adhesive tape until the glue has set. A suitable glue is, for example, OTTOCOLL® P 85. Figure 19 Figure 20 48 EGGER Compact Laminate 4. APPLICATIONS 4.1. Wall panelling Thanks to its robustness and suitability for everyday use, EGGER compact laminate is particularly well suited to interior wall panelling applications. We recommend a minimum board thickness of 8 mm for such applications. The walls and substructure should be completely dry prior to commencement of the panel installation. Always make provision for adequate air circulation behind the panels. The material should not be exposed to trapped moisture. All panels to be joined together must follow the same production direction. 4.1.1. Substructure and back ventilation Compact laminate should be fixed to a sturdy, corrosion-resistant and interlocking substructure which securely supports the weight of the wall panelling and ensures that ventilation behind the panels is provided. In drywall constructions, the fixings of both, the substructure and the compact laminate always have to be anchored to the studwork frame (see Figure 21). Concealed mounting Detail Figure 21 1 3 6 7 2 5 3 5 4 1 2 3 4 5 6 Figure 21 7 Studwork frame Insulation Compact laminate strips Two-layer gypsum fibreboard Compact laminate Adhesive Panel fixing tape The selection of the fixings has to be tailored to the substructure and the weight of the wall panelling. Different ambient conditions in front and to the rear of the elements can lead to warping. It is therefore essential that compact laminate wall panelling installations always make provision for adequate ventilation to the rear of the panels, which allows temperature and humidity to equalise. The installation should be vented into the room. Vertical studs generally permit air circulation. Where substructures are arranged horizontally, an appropriate construction must ensure that adequate ventilation is provided. The substructure should be vertically plumb and horizontally level to allow stress free mounting of the entire panel surface. Suitable substructures are vertically arranged strips of wood, aluminium or compact laminate (see also Figure 22). EGGER Compact Laminate 49 Visible screw fixing Detail Figure 22 1 1 2 2 1 2 Wooden battens EPDM jointing tape Figure 22 The maximum spacing of the battens and/or substructure depends on the chosen compact laminate thickness – see Figure 25. It is important to ensure that air inlet and outlet areas remain unobstructed so that air circulation is not impeded. Also ensure that the moisture of the surface to be panelled does not differ significantly from the moisture of the finished wall panel. 4.1.2. Visible mechanical fixings When compact laminate is attached to the substructure using screws, sufficient allowance must be made for expansion. For this purpose, floating points (see Figure 24) and one fixed point (see Figure 23) are drilled on the individual elements. The fixed point serves to evenly distribute the expansion movement and should be positioned as centrally as possible (see Figure 25) – the drill hole diameter is equal to the diameter of the fixing. The drill hole diameter of the floating points should be 2 – 3 mm larger than the fixing. The drill hole should be covered by the screw head. Washers should be used if necessary. In the illustrations, an EPDM sealing tape has been applied to the wooden substructure for protection against moisture. 1 1 1 Fixed point Floating-point Figure 23 Figure 24 EPDM jointing tape 50 EGGER Compact Laminate The required expansion allowance is determined according to the longest distance from the fixed point to the edge of the board. The floating point drill hole diameter must be increased by 2mm for every meter of length. For interior applications, the fixing distances listed in the following table can be used: Board thickness [mm / inch] Maximum fixing distances a [mm] b [mm] 6 615 400 8 790 500 10 920 670 12 960 900 13 970 920 EGGER compact laminates are self-supporting from a thickness of ≥ 6mm. = fixed point, × = floating point Figure 25 4.1.3. Concealed mechanical fixings The concealed fixing of compact laminates by suspension permits straightforward disassembly and is aesthetically more appealing than visible screw connections. The removal of panels is quick and simple and cables and pipework installed behind the elements are easily accessed. A further advantage is that, depending on the mounting system selected, elements can be adjusted retrospectively. In addition, this method allows elements to be mounted stress-free. With all suspension fixing systems, sufficient clearance must be allowed for raising and lowering the elements. This clearance or "suspension gap" will remain visible as a shadow gap. Batten suspension For this mounting method, a groove is cut into the horizontal substructure to hold the rebated rail attached to the wall element. For ease of fitting, the tongue of the rebated rail should be thinner than the groove. The rebated rails on the compact laminate elements should not extend across the full width of the elements, they should be intermittent in order to permit vertical air circulation. Rebated rails made of plywood or metal Z-profiles can be readily used. If a secure screw connection cannot be achieved with thin compact laminate elements, additional gluing is possible. Metal hardware suspension Metal hardware systems are also available for mounting wall elements (see Figure 26). The chosen system must be used in accordance with the recommendations of the manufacturer in order to ensure a secure installation. EGGER Compact Laminate 51 Figure 26 4.1.4. Gluing Compact laminate can also be mounted by gluing the panels to a rigid substructure, using permanently elastic adhesive systems especially developed for this purpose. The systems consist of the glue, a panel fixing tape and appropriate pre-treatment products for preparation of the surfaces. The purpose of the panel fixing tape is to initially secure the element until a permanent bond is achieved with the glue (see Figure 27). Please observe the processing instructions of the glue manufacturer. 1 2 3 4 1 Adhesive Compact laminate strips Panel fixing tape Compact laminate 2 3 4 Figure 27 Such glue systems are offered, for example, by the companies MBE, Innotec and DKS: Moderne Befestigungs Elemente GmbH Siemensstraße 1 D-58706 Menden Innotec Österreich Lofererstraße 83 A-6322 Kirchbichl DKS Technik GmbH Gnadenwald 90a A-6069 Gnadenwald t +49 (2373) 17430-0 info@mbe-gmbh.de www.mbe-gmbh.de t +43 (0)5332 70800 info@innotec.at www.innotec.at t +43 (0)5223 48488 office@dks.at www.dks.at 52 EGGER Compact Laminate 4.1.5. Joints Numerous options are available to create horizontal and vertical joints or seams (see Figure 28). However, it is important to ensure that the elements have sufficient clearance for expansion. Figure 28 4.2. Impact protection or partial wall panelling An impact protection solution or partial wall panelling is required wherever walls are expected to be exposed to increased wear and tear, for example in hospitals. In those locations, compact laminates are frequently used because they are robust and easy to care for. In addition to half height wall panelling (see Figure 29) partial impact protection solutions are also common practice. For partial impact protection solutions, compact laminate panels are usually fixed directly to the wall by means of visible screw connections. As there is no ventilation to the rear of the elements, a vapour barrier has to be installed between the compact laminate and the wall (see Figure 30). Half height wall panelling - drywall (stud framing) Glued solution 1 2 3 Wallpapered gypsum plasterboard 2 Stainless steel bracket 3 Compact laminate 1 Figure 29 EGGER Compact Laminate 53 Solid wall with partial impact protection Screw-fixed solution 1 2 1 2 Compact laminate Vapour barrier Figure 30 4.3. Sanitary and shower cubicles When compact laminate is used in sanitary facilities, it is important to ensure during construction and installation that it is not subjected to standing water and that adequate ventilation is provided in these rooms. It is imperative that only corrosion-free construction materials and fixing devices are used. For application in wet areas it is essential to mechanically reinforce corner connections by using dowels or splines, for example, and to employ a waterproofing adhesive system. For commercial applications subjected to increased wear and tear, a minimum distance of 120mm must be maintained between the floor and lower edge of the board (see Figure 31). 1 1 Figure 31 Spacing 120 mm 54 EGGER Compact Laminate 4.3.1. Glued compact laminate solutions Compact laminates can also be used in non-commercial sanitary facilities, for Detail 1, Figure 32, top edge finish example in private households and/or hotels. It is important that adequate ventilation is provided in these rooms and that the compact laminates can dry after 1 the shower has been used. Corrosion-free materials must be used for structures and fixings. Absorbent mineral substrates such as walls, respectively plaster, have 3 to be primed with flexible waterproofing barriers. These barriers are generally 2 brushed on and prevent water from penetrating the substrate. The German Construction Confederation offers a leaflet for such sealing and barrier products ("Waterproofing barriers for installations with tiles and boards"). This leaflet describes liquid sealing compounds for use in conjunction with tiles and boards in 1 interior and exterior applications, taking into account defined moisture exposure 2 classes and substrates. The company Knauf, for example, offers such a sealant 3 Air gap Adhesive Panel fixing tape called “Flächendicht”. The moisture exposure classes of the materials have to be coordinated with the manufacturers or suppliers, and observing the processing Detail 2, Figure 32, corner solution instructions of the respective manufacturers is mandatory. The following are two 1 possible construction examples (see Figures 32 and 33). 2 3 Aluminium strips 4 5 5 Sealed substrate Aluminium strip 3 Compriband (expanding sealing tape) 4 Silicone seal 5 Compact laminate 1 2 Detail 3, Figure 32, bottom edge finish 2 1 1 Figure 32 – Glued compact laminate solution 1 2 Compriband (expanding sealing tape) Silicone seal EGGER Compact Laminate 55 Compact laminate strips Detail 1, Figure 33, top edge finish 1 3 2 1 2 3 Air gap Adhesive Panel fixing tape Detail 2, Figure 33, bottom edge finish 1 4 3 2 1 2 3 4 Air gap Tiled skirting Silicone seal Min. distance to floor 50 mm Figure 33 – Glued compact laminate solution 2 Detail 3, Figure 33, corner solution 1 2 1 2 3 4 5 Sealed substrate Compact laminate strips Compriband (expanding sealing tape) Silicone seal Compact laminate 3 4 5 5 56 EGGER Compact Laminate 4.4. Hinged doors Doors should not be wider than they are high. As dimensional movement along the length is only approximately half as great as it is across the width, it is advisable to cut door leaves in the longitudinal direction of the compact laminate. Excessive differences in temperature or relative humidity at the front and reverse sides of a door panel can cause the compact laminate to warp. For this reason, it is imperative that adequate air circulation is provided for installations such as toilet cubicles or changing rooms for example. The door width, height and weight are deciding factors for the number of hinges required. Other factors, such as the installation location or whether additional stress is to be expected from the attachment of coats hooks, for example, can vary greatly from case to case and must be taken into account. The information provided (see Figure 34) should therefore be regarded as a guideline only for a door in 10mm thickness and a width of up to 600mm. Performing a trial mounting is always recommended. For heavy duty applications, an additional hinge can be fitted at max. 100mm below the upper hinge. The upper and lower hinges should be located at a minimum distance of 100mm max., measured from the outer edge (X) of the panel. Suitable hinges are offered by the companies HÄFELE or Prämeta, for example (see Figure 35). Figure 34 Source: HÄFELE Special hinge – Article 344.75.051 Figure 35 EGGER Compact Laminate 57 4.5. Table tops Compact laminate is very suitable for table top applications, for example in offices, conference rooms, schools, and workshops. The board thickness, fixing distances and the overhang over the frame must be configured in accordance with the loads to be expected (see Figure 37). Table tops must have a minimum thickness of 10 mm so that sufficient material is available to ensure secure screw connections. There are several fixing methods for attaching tops to frames or bases. The important factor is to ensure that the assembly is stress-free. Screws can be driven directly into the board or a screw-in sleeve can be used. The fixing points in the substructure must be implemented with sufficient clearance for expansion. The diameter of the drill hole should be 2 – 3 mm larger than the diameter of the fixing device (see Figure 36). Board thickness [mm] Overhang [mm] Mounting distance [mm] 10 170 310 12 240 390 13 270 440 Figure 36 Overhang Mounting distance Figure 37 58 EGGER Compact Laminate 4.6. Sink installation Compact laminates are also popular for work surfaces in the kitchen, as well as for vanity units in toilet facilities. In these fields of application, the installation of a sink or a washbasin is necessary. The following solutions (see Figure 38 and 39) are generally implemented: Figure 38, Solution 1 Figure 39, Solution 2 EGGER Compact Laminate 59 5. TECHNICAL DATA Property Standard Resistance to surface wear Resistance to impact by large diameter ball EN 438-2:10 EN 438-2:21 Black core Unit Flammex White core CGS ACS CGF ACF BCS Starting abrasion point 150 - 150 - 150 - Abrasion value 350 - 350 - 350 - *4 Number of revolutions (per minute) Drop height in mm 2 mm ≤ t < 6 mm 1,400 800 1,400 800 - - 6 mm ≤ t 1,800 800 1,800 800 - - ≤ 10 ≤ 12 ≤ 10 ≤ 12 - - Scratch resistance EN 438-2:25 Rating Diameter of the impression in mm 3 2 3 2 3 2 Resistance to staining group 1 and 2 EN 438-2:26 Rating 5 5 5 5 5 5 Resistance to staining group 3 EN 438-2:26 Rating 4 4 4 4 4 4 Light fastness (Xenon arc lamp, surface) *1 EN 438-2:27 Grey scale 4 to 5 4 4 to 5 4 4 4 - - - - 3 3 Surface 4 - 4 - 4 - Core - - - - 3 *3 3 *3 3 - 3 - 3 12 Surface Core Resistance to crazing EN 438-2:24 Rating Resistance to cigarette burns EN 438-2:30 Rating Flatness *2 EN 438-2:9 Depending on thickness in mm/m Resistance to immersion in boiling water EN 438-2:12 2,0 mm ≤ t < 6,0 mm 8 8 8 8 12 6,0 mm ≤ t < 10,0 mm 5 5 5 5 8 8 10.0 mm ≤ t 3 3 3 3 5 5 Mass increase in % 2 mm ≤ t < 5 mm 5 5 - - 5 5 t ≥ 5 mm 2 2 2 3 3 3 Thickness increase in % 2 mm ≤ t < 5 mm 6 6 - - 6 6 t ≥ 5 mm 2 2 2 6 4 4 4 4 4 4 4 4 0.6 Appearance in degrees Dimensional stability at elevated EN 438-2:17 Cumulative dimension change in % 2 mm ≤ t < 5 mm temperatures t ≥ 5 mm Resistance to dry heat EN 438-2:16 Rating La 0.4 0.4 - - 0.6 Tb 0.8 0.8 - - 1 1 La 0.3 0.3 0.3 0.3 0.5 0.5 Tb 0.6 0.6 0.6 0.6 0.8 0.8 4 - 4 - 4 3 Resistance to water vapour EN 438-2:14 Rating 4 3 4 3 4 Resistance to wet heat (100 °C) EN 12721:2009 Rating 4 - 4 - - - Density EN ISO 1183-1 g/cm³ ≥ 1.35 ≥ 1.35 ≥ 1.35 ≥ 1.35 ≥ 1.4 ≥ 1.4 Flexural modulus EN ISO 178 MPa 9,000 9,000 9,000 9,000 9,000 9,000 Flexural strength EN ISO 178 MPa 80 80 80 80 80 80 Tensile strength EN IOS 527 MPa 60 - 60 - 60 - Extraneous darkening and/or photochromism are due to the shock effect of accelerated exposure and are not characteristics of natural exposure. *2 The defined flatness values apply to compact laminate with decor on two sides. The limits for compact laminate with decor on one side need to be agreed upon. *1 *3 *4 t a b Moderate cracks along the edges of the test specimen. Compact laminates with a white core in combination with pearlescent decors are not defined by the Standard. This combination is, however, possible and the values shown in the table under the pearlescent icon apply to this constellation. t is the nominal thickness of the compact laminate. L in longitudinal direction i.e. compact laminate length. T in transverse direction i.e. compact laminate width. 60 EGGER Compact Laminate 6. CLEANING AND MAINTENANCE RECOMMENDATIONS Because of its durable, hygienic and dense surface, EGGER compact laminate does not require special care. As a general rule, stains and spilled substances such as tea, coffee and wine etc. should be cleaned up immediately, as the cleaning effort increases if they are left to dry. When cleaning is necessary, mild agents should be used. Cleaning agents must in particular not contain any abrasive components, as they may adversely affect the gloss level or scratch the surface. The following recommendations should be observed in daily use: Placing burning cigarettes on the compact laminate surface leads to surface damage. Always use an ashtray. Compact laminate surfaces should not be used as a cutting surface, as this can also leave cutting marks on highly resistant compact laminate surfaces. Always use a chopping board. Placing hot cooking utensils such as saucepans and frying pans directly from the hob or oven onto the compact laminate surface should be avoided, as, depending on the heat exposure, a change in the gloss appearance or damage to the surface can arise. Always use heat resistant mats. Spilled liquids should always be cleaned up immediately, as prolonged exposure to some substances may cause a change in the gloss level of compact laminate surfaces. Especially in the areas around cut-outs and joints, spilled liquids should always be cleaned up quickly and thoroughly. These recommendations apply especially to matt compact laminate surfaces. These have a distinctive look and feel, but have a greater tendency to show wear and tear. More detailed information can be found in our "EGGER laminate cleaning and maintenance instructions" leaflet at www.egger.com/compactlaminate. 7. WASTE TREATMENT Due to their very high calorific value, compact laminates are very suitable for thermal disposal in appropriate combustion plants. Country specific waste management laws and regulations have to be observed at all times. Provisional note: This product brochure has been carefully drawn up to the best of our knowledge. We accept no liability for any mistakes, errors in standards or printing errors. Furthermore, the continuous development of EGGER products might result in differences, as well as renewals of standards and documents of public law. The content of this brochure is therefore not an instructions of use and not legally binding. EGGER Compact Laminate 61 ZOOM IS SO MUCH MORE: With Zoom we don’t just offer you high product quality and the latest trend orientated decors but also a wide range of helpful services: Your everyday resource. JUST GIVE US A CALL. YOUR ZOOM HOTLINE Sometimes you need an answer quickly. Our Zoom Hotline team will take your sample order also on the phone, will be happy to answer your technical questions and advise you in the selection of products and decors. Just give us a call! NEED TO VISUALISE YOUR IDEAS? USE VDS PROFI With our Virtual Design Studio (VDS) software you can visualise your own ideas and those of your customers with ease. Place EGGER decors into a wide variety of available room sets or alternatively upload your own and view the chosen decors in situ as furniture and on floors. Actively involve your customers in the room design process and boost the success of your consultation: www.egger.com/vds ALWAYS AT YOUR FINGERTIPS, EVEN ON THE MOVE. VDS ONLINE / VDS APP With the free VDS ONLINE version and the VDS App you can view the EGGER Zoom and flooring decors on all mobile devices. All decors can also be enlarged to full screen size. In addition, there are 30 room sets available for individual visualisation. www.egger.com/vdsonline FOR EVERYTHING ELSE VISIT OUR WEBSITE From technical data sheets, processing instructions and certificates to product availability, distributor searches and the latest news it can all be found quickly and efficiently at www.egger.com All decors mentioned and shown are reproductions. Due to variables in the printing process, colours may vary from the actual product. 62 EGGER Compact Laminate AVAILABILITY GUIDE – FULL PRODUCT OVERVIEW Eurodekor Melamine Faced Chipboards Laminates ABS Edging Pearlescent Decor All dimensions in millimeter. 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m WHITE COLOURS GFE Painting Grade W908 SM Basic White W908 ST2 Basic White W911 SM Cream White * W911 ST2 Cream White * W911 ST15 Cream White * W980 SM Platinum White W980 ST2 Platinum White W980 ST15 Platinum White W1000 ST2 Premium White W1000 ST9 Premium White W1000 ST18 Premium White W1000 ST22 Premium White W1000 ST26 Premium White W1000 ST30 Premium White W1000 A1 Premium White W1000 ST88 Premium White W1001 ST9 Solid Premium White W1200 ST2 Porcelain W1200 ST9 Porcelain ST15 Alabaster UNI COLOURS U104 2014 * 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 63 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 64 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging All dimensions in millimeter. U107 ST9 Velvet Yellow U108 ST15 Vanilla U108 ST30 Vanilla U113 ST15 Cotton U114 ST15 Yellow U129 ST15 Sun Yellow U140 ST9 Saffron U142 ST9 Lime U143 ST15 Signal Yellow U146 ST15 Maize Yellow U147 ST15 Melon U156 ST9 Sand Beige U204 ST9 Camel U206 ST9 Malaga U216 ST15 Oyster U222 ST15 Crema U224 ST15 Silk U311 ST15 Burgundy U311 ST30 Burgundy U317 ST9 Clay U321 ST15 Red U323 ST15 Chilli Red U328 ST15 Lipstick Pearlescent Decor 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 65 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 66 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging Pearlescent Decor All dimensions in millimeter. U329 ST15 Tangerine U330 ST9 Aubergine U330 ST88 Aubergine U332 ST15 Orange U334 ST9 Powder U336 ST9 Orchid U337 ST9 Fuchsia U337 ST88 Fuchsia U343 ST9 Vino U400 ST9 Violet U506 ST15 Marine U514 ST15 Baltic Blue U518 ST9 Ice Blue U522 ST15 Horizon U525 ST15 Blue U532 ST15 Petrol U533 ST15 Polar Blue U535 ST15 Aqua U536 ST15 Lagoon U537 ST15 Brilliant Blue U537 A1 Brilliant Blue U538 ST15 Ocean U539 ST9 Steel Blue 2014 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 67 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 68 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging Pearlescent Decor All dimensions in millimeter. U540 ST9 Denim U608 ST9 Pistachio U617 ST9 Wasabi U625 ST15 Apple Green U628 ST15 Green U630 ST15 Lime Green U630 A1 Lime Green U631 ST9 Olive U632 ST15 Grass Green U633 ST15 Turquoise U634 ST15 Velvet Green U635 ST9 Moss U701 ST9 Platinum U702 ST9 Cashmere U708 ST15 Light Grey U727 ST9 Stone Grey U727 ST22 Stone Grey U727 ST26 Stone Grey U730 ST9 Basalt U732 ST15 Dust Grey U741 ST9 Lava U741 ST22 Lava U748 ST9 Truffle 2014 2014 2014 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 69 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 70 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging All dimensions in millimeter. U750 ST9 Taupe Grey U763 ST15 Pearl Grey U763 ST18 Pearl Grey U765 ST15 Silver Grey U775 ST15 White Grey U795 ST9 Brown Grey U803 ST15 Black Brown U807 ST9 Nougat U808 ST9 Mocha U961 ST2 Graphite U961 ST15 Graphite U961 ST30 Graphite U963 ST15 Diamond Grey U999 ST2 Black U999 ST11 Black U999 ST15 Black U999 ST18 Black U999 ST30 Black WOOD REPRODUCTIONS H045 ST15 Light Planked Timber H047 ST15 Dark Plum Butcher-Block H056 ST70 Core Maple H078 ST79 Flowered Beech Pearlescent Decor 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 71 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 72 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging All dimensions in millimeter. H087 ST79 Flowered Maple H178 ST15 Afzelia Butcher-Block H199 ST70 Wenge Butcher-Block H806 ST9 Anthracite Oak Horizontal H815 ST9 Cherry Horizontal H834 ST9 Light Natural Oak Horizontal H835 ST9 Light Oak Design H836 ST15 Dark Oak Design H850 ST9 Macassar Horizontal H886 ST15 Beech Horizontal H887 ST9 Maple Horizontal H888 ST15 Walnut Horizontal H1105 ST9 Aspen Beige H1106 ST9 Aspen Grey H1109 ST15 Dark Samoa H1110 ST10 Splitwood H1111 ST15 Snakewood H1112 ST10 Zanzibar H1129 ST15 Thermo Oak H1133 ST9 Arlington Oak Horizontal H1137 ST11 Black Brown Ferrara Oak H1145 ST10 Natural Bardolino Oak H1146 ST10 Grey Bardolino Oak Pearlescent Decor 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 73 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 74 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging Pearlescent Decor All dimensions in millimeter. H1150 ST10 Grey Authentic Oak H1151 ST10 Brown Authentic Oak H1189 ST10 Smoked Brown Bonanza Oak H1215 ST22 Brown Cassino Ash H1250 ST36 Navarra Ash H1277 ST9 Light Lakeland Acacia H1298 ST22 Sand Lyon Ash H1334 ST9 Light Ferrara Oak H1372 ST22 Natural Aragon Oak H1377 ST36 Sand Orleans Oak 2014 H1379 ST36 Brown Orleans Oak 2014 H1424 ST22 Woodline Cream H1428 ST22 Woodline Mocha H1474 ST22 White Avola H1476 ST22 Champagne Avola H1484 ST22 Brown Grey Avola H1486 ST36 Jackson Pine H1487 ST22 Bramberg Pine H1502 ST15 Alder H1511 ST15 Bavarian Beech H1518 ST15 Natural Beech H1521 ST15 Maple H1555 ST15 Wenge 2014 2014 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 75 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 76 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging Pearlescent Decor All dimensions in millimeter. H1582 ST15 Ellmau Beech H1599 ST15 Chocolate Tyrolean Beech H1615 ST9 Romana Cherry H1706 ST15 Cherry H1733 ST9 Mainau Birch H1793 ST9 Lava Tortona 2014 H1793 ST27 Lava Tortona 2014 H1796 ST9 Natural Tortona 2014 H1796 ST27 Natural Tortona 2014 H1867 ST9 Cream Canadian Maple H1887 ST9 Natural Starnberg Maple H1920 ST9 Natural Tyrolean Beech H1950 ST15 Natural Calvados H1951 ST15 Sienna Calvados H1952 ST15 Amber Calvados H2572 ST9 Woodstock H3005 ST22 Grey Beige Zebrano H3006 ST22 Sand Zebrano H3012 ST22 Coco Bolo H3025 ST15 Macassar H3031 ST9 Dark Cordoba Olive H3058 ST22 Mali Wenge H3078 ST22 Hacienda White 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 77 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 78 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging Pearlescent Decor All dimensions in millimeter. H3080 ST15 Sierra Mahogany H3081 ST22 Hacienda Black H3082 ST22 Amazonas H3090 ST22 Driftwood H3113 ST15 Lindau Pearwood H3114 ST9 Tirano Pearwood H3128 ST15 Natural Plum H3129 ST9 Autumn Plum H3303 ST10 Natural Arlington Oak H3304 ST9 Grey Lacquered Chateau Oak H3306 ST9 Anthracite Chateau Oak H3309 ST9 Sand Gladstone Oak 2014 H3309 ST28 Sand Gladstone Oak 2014 H3325 ST9 Tobacco Gladstone Oak 2014 H3325 ST28 Tobacco Gladstone Oak 2014 H3326 ST9 Grey Beige Gladstone Oak 2014 H3326 ST28 Grey Beige Gladstone Oak 2014 H3331 ST10 Natural Nebraska Oak H3332 ST10 Grey Nebraska Oak H3344 ST36 Highline Oak H3363 ST9 Anthracite Highland Oak H3387 ST11 Rustic Oak H3389 ST11 Natural Light Oak 2014 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 79 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 80 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging Pearlescent Decor All dimensions in millimeter. H3400 ST22 Rustic Pine H3420 ST36 Thermo Pine H3660 ST9 Light Venetian Cherry H3662 ST9 Natural Light Venetian Cherry H3700 ST10 Natural Pacific Walnut H3702 ST10 Tobacco Pacific Walnut H3704 ST15 Tobacco Aida Walnut H3734 ST9 Natural Dijon Walnut H3739 ST15 Walnut Butcher-Block H3753 ST22 Country Montana Larch H3755 ST22 White Swiss Larch H3758 ST9 Helsinki Birch H3760 ST9 White Cape Elm 2014 H3760 ST29 White Cape Elm 2014 H3766 ST9 Dark Brown Cape Elm 2014 H3766 ST29 Dark Brown Cape Elm 2014 H3775 ST9 Light Tennessee Walnut H3778 ST9 Natural Caribbean Walnut H3840 ST9 Natural Mandal Maple H3911 ST9 Natural Tauern Beech F583 ST22 Fino Bronze F584 ST22 Fino Cinnamon F900 ST9 Artwood Light 2014 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 81 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 82 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging All dimensions in millimeter. F901 ST9 Artwood Brown MATERIAL REPRODUCTIONS F041 ST15 Sonora White F042 ST70 Sonora Black F043 ST70 Sonora Black Blue F105 ST15 Torano Marble F131 ST15 Trani Light Grey F133 ST82 Trento Grey Beige F145 ST2 Sardo Granite F147 ST82 Valentino Grey F148 ST82 Valentino Light Brown F161 ST70 Artic Blue Grey F166 ST9 Aurora Bianco F202 ST15 Black Marble F207 ST70 Portoro Black Brown F210 ST9 White Grey Amalvi Marble F211 ST9 Brown Amalvi Marble F212 ST70 Lazio Grey Blue F213 ST70 Lazio Anthracite F214 ST10 Peacock Slate F236 ST15 Terrano Grey F238 ST15 Terrano Black F274 ST9 Light Concrete Pearlescent Decor 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 83 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 84 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging Pearlescent Decor All dimensions in millimeter. F275 ST9 Dark Concrete F276 ST9 Arkosa Sand F277 ST9 Arkosa Grey F292 ST9 Tivoli Beige F310 ST87 Rust Ceramic 2014 F311 ST87 Anthracite Ceramic 2014 F371 ST82 Galizia Grey Beige F381 ST10 Silk Fibre F382 ST10 Titanium Fibre F383 ST10 Bronze Fibre F385 ST10 Cement F390 ST82 Valetta Sand F396 ST10 Basaltino Grey F402 ST10 Vulcano Grey F403 ST10 Vulcano Brown F405 ST82 Galaxy White F407 ST82 Galaxy Dark Brown F425 ST10 Beige Linen F426 ST10 Grey Linen F427 ST10 Beige Leather F428 ST10 Brown Leather F437 ST2 Quartz Saffron F438 ST2 Quartz Indigo 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 85 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 86 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging All dimensions in millimeter. F440 ST2 Quartz Bronze F447 ST2 Quartz Lava F488 ST2 Quartz Cubanit F489 ST2 Quartz Inox F495 ST2 Quartz Glass F501 ST2 Titanium F509 ST2 Aluminium F598 ST2 Quartz Copper F633 ST15 Grey Brown Metallo F636 ST15 Titanium Blue Metallo F784 ST2 Stainless Steel Microline F870 ST10 Leon Slate REAL ALUMINIUM LAMINATES FA101 Brushed Aluminium FA102 Brushed Steel Effect DIGITAL PRINTING D0014 ST15 Blue & Grey Pepita D0015 ST15 Blue & Brown Pepita D0016 ST15 Green & Grey Pepita D0017 ST15 Lilac Variations D0018 ST15 Beige Variations D0020 ST15 Volcano Flames D0021 ST15 Desert Flames Pearlescent Decor 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 87 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 88 EGGER Compact Laminate Eurodekor Melamine Faced Chipboards Laminates ABS Edging All dimensions in millimeter. D0022 ST15 Jungle Flames D0023 ST15 Brown & Beige Flowers D0024 ST15 Grey & Blue Flowers D0025 ST15 Walnut Design D0026 ST15 Metal Disk Pearlescent Decor 8; 16; 18; 19; 25 10; 12; 22; 28; 30; 32; 38 0.8 0.6 0.8 200 m 75 m 54 × 2 42 × 2 42 × 0.8 31 × 2 23 × 2 23 × 0.8 22 × 0.4 (*23 × 0.4) 2,350 × 1,310 MED 2,150 × 1,020 2,150 × 950 Off the roll available from 2,000 × 1,310 MED 3,050 × 1,310 Only for vertical use, compact boards only one side pearlescent 2,800 × 1,310 2,800 × 2,070 E1 P2 CE Further formats, thicknesses and core boards, e.g. Eurospan E1 P3/MR CE, Eurospan JP F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2), Eurospan Flammex B/B1/M1, Eurospan E1 P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards, EGGER OSB Combiline, upon request. FLEX Available 25 m 50 m 32 38 15 19 22 19 doubled to 38 3; 4; 5; 6; 8; 10; 12; 13 5; 6; 8; 10; 12; 13 2,800 × 1,310 Classic Finest Compact Laminates 2,800 × 2,070 Flammex black core Window Sills 2,790 × 2,060 MOD 801/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 5,200 and 4,100 × 500) Front Elements Black core / White core MOD 800/6 4,100 × 160; 200; 250; 300; 400 (W980 also in 4,100 × 500) MOD 200/3 two-sided profile 2,800 × 160; 271; 296; 396; 446; 496; 546; 596 Laminate Splashback Panels MOD 300/4 two-sided profile MOD 90 Length upon request × 640 Eurospan Worktops 2,800 × 680 MOD 300/3 two-sided profile Length upon request × 920 MOD 300/3 one-sided profile with or without hot melt adhesive Melamine Edging Length upon request × 1,200 Length upon request × 600 24 × 0.3 EGGER Compact Laminate 89 Eurolight Lightweight Boards ProAcoustic Acoustic Boards 38 50 20 Your everyday resource Benefit from the comprehensive services of EGGER and register now: www.egger.com/myegger EN-OS_04/2016 Technical modifications and printing errors excepted. FRITZ EGGER GmbH & Co. OG Holzwerkstoffe Weiberndorf 20 6380 St. Johann in Tirol Austria t +43 50 600-0 f +43 50 600-10111 info-sjo@egger.com 奥地利爱格公司上海代表处地址 中国上海市南京西路580号南证大厦3609室 邮编200041 电话 +86 21 5234 0688 传真 +86 21 5234 0988 china@egger.com Fritz Egger AG 1-9-5 Ginza, Chuo-ku, Tokyo-to 104-0061 Japan t +81 3 6228 6470 f +81 3 6228 6471 m +81 90 8777 7719 japan@egger.com EGGER Productos de Madera Limitada San Francisco de Asís 150, Oficina 403 Vitacura, Santiago Chile ZIP code: 7650747 t +56 2 2243 8583 chile@egger.com Arvind Katyal B-5, Gulmohar Park 110049 New Delhi India t +91 11 32600929 f +91 11 46050305 india@egger.com EGGER AUSTRALASIA PTY LIMITED P.O. Box 697 Carlton South, Victoria Australia, 3053 m +61 448 200 013 australia@egger.com
