PDLPC416FR-KNX LightMaster Dimmer Actuator General Description The PDLPC416FR-KNX is designed to provide cost effective control of multiple lighting control protocols for electronic lamp drivers and actuators. Each of the four control outputs support DALI broadcast, DALI Addressed, 1-10V and DSI protocols. The control signals can be programmed to operate in tandem with the four internal switched outputs, which will automatically isolate the power circuit when all associated channels are at 0%. This feature is useful for energy savings applications, as DALI ballasts draw a significant amount of power when the lamps are turned off via a DALI command. The device is DIN rail mountable, designed to be installed in a switchboard next to the circuit breakers supplying power to the controlled lighting circuits. The PDLPC416FR-KNX contains an integral DALI bus power supply, removing the need for an additional external device. Technical Data Control Circuit Supply 100-240V 50/60Hz Single Phase at 0.5A Control Outputs 4 x Control Outputs, each selectable to; • DALI broadcast: max 20 DALI loads/ ch and a total limit of 80 fittings max per box • DALI addressed: max 20 DALI loads/ ch and a total limit of 64 DALI fittings max per box • 1-10V: max 20 1-10V loads/ch (max 10mA sink/source) and a total limit of 80 1-10V ballast max per box • DSI: max 20 DSI loads/ch and a total limit of 80 DSI fittings max per box Mains Outputs 4 x 16 Amp feed thru single/multiphase switched circuits for mains supply max. inrush current 500A 1 x maintained NC switched output, rated 5A resistive Control IO 1 x KNX TPI bus, 21-30Vdc, max 10mA bus load 4 x voltage free single pole switched inputs, SELV DALI bus Power Supply In built, rated 40mA per channel @ 15V User Controls Over-ride switch for each switched channel On/Off status indicator for each switched output KNX Programming push button & LED Diagnostic Functions* • DALI lamp failure reporting • DALI Ballast failure reporting • DALI emergency test reporting • DALI ballast runtime tracking for each ballast • Device Online/Offline status Supply Terminals Line, Neutral, Earth 1 x 4mm2 max conductor size KNX TPI Bus Terminals Wago 243, 0.6-0.8mm single core conductor diameter Output Terminals 4 x Ballast power circuit Line In, Line out 1 x 4mm2 max conductor size 1 x maintained NC switched output, Line In, Line Out, 1 x 4mm sq max conductor size 4 x Ballast control circuit - D+, D1 x 2.5mm2 max conductor size Input Terminals: 4 x voltage free single pole switched inputs, SELV, DC1-DC4, 2 x 1mm sq. max. conductor size per pole Environment -5º to 45ºC operating ambient temperature -25º to 70ºC storage temperature 0% to 90% RH non condensing Compliance CE, KNX Enclosure Polycarbonate DIN Rail enclosure (12 units wide) Dimensions H 96mm x W 211mm x D 75mm Weight Packed weight 0.65kg * Compatible application software is required for analysing diagnostic data. The availability of some diagnostics is dependent on the ballast type. PDLPC416FR-KNX LightMaster Dimmer Actuator Load Compatibility DALI, DSI and 1-10V HF ballasts DALI, DSI and 1-10V transformers DALI, DSI and 1-10V LED drivers DALI and DSI Relay Modules Electrical Diagram E N L Supply: 100-240V 50/60Hz 1 Phase Switch CH1 In Switch CH1 Out Switch CH2 In Switch CH2 Out µP Switch CH3 In Switch CH3 Out DC1 Switch CH4 In COM DC2 Switch CH4 Out DC3 EM Switch COM DC4 KNX EM Switch 1-10V/DSI/DALI Ballast Ch1 DA – Ballast Ch1 DA + 1-10V/DSI/DALI Ballast Ch2 DA – Ballast Ch2 DA + 1-10V/DSI/DALI Ballast Ch3 DA – Ballast Ch3 DA + 1-10V/DSI/DALI Ballast Ch4 DA – Ballast Ch4 DA + – + For further information contact: www.philips.com/knx • knx.info@philips.com PDLPC416FR-KNX Data Sheet Rev C May 2012 Specifications subject to change without notice. © Not to be reproduced without permission. Unit 6, 691 Gardeners Road Mascot 2020 Australia. ABN 33 097 246 921