Catalog Number
Notes
FEATURES & SPECIFICATIONS
Type
RELOC®-Ready Luminaire
INTENDED USE
The RELOC®-Ready Luminaire (RRL) connectors enables a simple and consistent factory installed
option across all ABL luminaire brands. When ordered on a RELOC fixture cable, cord drop, drop cable,
power tee; the line side of the connector will be factory attached to all the wire leads except for the
ground wire. When ordered with the luminaire, the load side of the connector will be prewired based
on the appropriate wiring instruction selection.
Universal Fixture Connector
RRL
ELECTRICAL
•18 AWG solid wire only; stranded not available.
• Tin-bonded 18 AWG (≤16 strand) acceptable.
•Current Interruption 10 cycles.
SYSTEM FEATURES
•RRL connector used with Quick-Flex®, System 820 and OnePass® systems.
•Load side of connector factory attached to luminaire. Refer to luminaire spec sheet for ordering
information.
•4-pole mating connector with push-in terminations allows for simple installation.
•Touch-safe design on both halves, meets UL/CSA requirement.
•Wiping contact design allows safe disconnect under load.
•RoHS Compliant
WARRANTY
LISTINGS
•5-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
•UL 2459
•CSA- C22.2 NO. 2459
•NEC 2008 410.130(G) Compliant
Actual performance may differ as a result of end-user environment and application.
Note: Specifications subject to change without notice.
•CEC 30-308(4) Compliant
Load Side RELOC®-Ready Luminaire
ORDERING LOGIC
Line Side RELOC®
Example: RRLA
For shortest lead times, configure product using bolded options.
RRL
Series
Series
RRL
RRL
Wiring Instructions
A
B
C
AB
AE
ABE
C12S
22N
122N
Ballast/driver wired to pin position #1 (120V,277V,347V - Phase A)
Ballast/driver wired to pin position #1 & #2 (208V, 240V, 480V - Phase A)
Ballast/driver wired to pin position #2 (120V,277V,347V - Phase B)
Ballast/driver wired to pin position #3 & #4 (208V, 240V, 480V - Phase B)
Ballast/driver wired to pin position #3 ( 120V,277V,347V - Phase C ) 1
Outboard ballast/driver wired to pin position #1 (120V,277V,347V - Phase A)
Inboard ballast/driver wired to pin position #2 (120V, 277V, 347V - Phase B)
Outboard ballast/driver wired to pin position #1,#2 (208V, 240V, 480V - Phase A)
Inboard ballast/driver wired to pin position #3,#4 (208V, 240V, 480V - Phase B)
Ballast/driver wired to pin position #1 (120V,277V,347V - Phase A)
Emergency ballast/driver wired to pin position #2 (120V,277V,347V - Phase B) 2
Ballast/driver wired to pin position #1 (120V,277V,347V - Phase A)
Ballast/driver wired to pin position #2 (120V,277V,347V - Phase B)
Emergency ballast/driver wired to pin position #3 (120V,277V,347V - Phase C) 1,2
Ballast/driver wired to pin position #1 (120V,277V,347V - Phase A)
Low voltage wire (positive/purple) (data1) wired to pin position #2
Low voltage wire (common/gray) (data2) wired to pin position #3 1,3
Ballast/driver wired to pin position #1 & #2 (208V, 240V, 480V - Phase A) 1,3
Low voltage wire (positive/purple) (data1) wired to pin position #2
Low voltage wire (common/gray) (data2) wired to pin position #3 1,3
Ballast/driver wired to pin position #2 and pin position #3 (120V,277V,347V - Phase B) 1
Ballast/driver wired to pin position #1 and #4 (120V,277V,347V - Phase A)
Ballast/driver wired to pin position #2 and #3 (120V,277V,347V - Phase B) 1
Example: QFC277 12/3G11 G RRL
QSFC277 12/2G11 G RRL
QPT277 12/3G09 RRL
SSC 277 F U 11 G RRL
OCS 480 10 RRL
OD 277 12/3G 15 RRL
NOTE
1. All hot conductors and neutral wires present in RELOC cable, drop
cable or power tee.
2. G option required for QFC, QSFC, and SSC fixture cables.
3. Ground wire will include poke-in wire connector.
4. See RELOC spec sheets to order with RELOC systems.
NOTES
1. RRLC, RRLABE, RRLC12S, RRL2N, and RRL122Noptions can not be used with the
Quick-Flex system: QFC, QSFC, QPT, and QD.
2. AE and ABE Commercial fixtures should disconnect the TSPL before unplugging
the RRL so it does not go into discharge mode.
3. RRLC12S option is to be used with the OnePass OD and 820 SSC, PT, and DC for
0-24V integrated single-circuit or 0-10V low voltage controls applications.
RRL
One Lithonia Way Conyers, GA 30012 Phone: 800-241-4750 Fax: 770-808-8650 www.relocwiring.com © 2013-2015 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/15/15
1 of 1
RRL RELOC®-Ready Luminaire
DIMENSIONS
Dimensions are shown in inches (millimeters)
LOAD SIDE
LINE SIDE
Connects to Fixture. Installed on
fixture at factory or by customer.
Connects to RELOC Fixture Cable.
Installed on Reloc cable at the factory.
WIRING INSTRUCTIONS
Pin position and conductor functions by voltage.
Position #
Function
1
Hot 1
2
Hot 2
3
Hot 3
4
Neutral
Wiring Instruction
Standard Wiring Applications
120V,277V,347V
X
X
Function
X
1
Hot 1
X
X
X
2
Hot 2
X
X
3
Hot 3
4
Neutral
X
X
X
X
X
RRLA
RRLB
RRLC
RRLAB
Two Neutral Applications
120V, 277V, 347V
Normal and Emergency
Applications 120V, 277V, 347V
Position #
Wiring Instruction
X
X
RRLAE
RRLABE
Function
1
Hot 1
X
1
Hot 1
X
2
Hot 2
X
X
2
Data 1, Positive ( + )
X
3
Neutral 2
X
X
3
Data 2, Common ( - )
X
4
Neutral 1
X
4
Neutral
X
RRL22N
Special Industrial Voltage
Applications 208V, 240V, 480V
Position #
Function
1
Hot 1
X
2
Hot 2
X
3
Hot 3
4
Hot 4
Wiring Instruction
RRL122N
Wiring Instruction
RRLC12S
Position #
Function
Class I Class II Wiring
Applications 208V, 240V, 480V
1
Hot 1
X
X
2
Data 1, Positive ( + )
X
X
3
Data 2, Common ( - )
X
X
X
4
RRLB
RRLAB
X
X
RRLA
Function
Class I Class II Wiring Applications 120V, 277V
Position #
Wiring Instruction
Position #
X
Hot 2
Wiring Instruction
X
RRLC12S
RRL
One Lithonia Way Conyers, GA 30012 Phone: 800-241-4750 Fax: 770-808-8650 www.relocwiring.com © 2013-2015 Acuity Brands Lighting, Inc. All rights reserved. Rev. 01/15/15
2 of 2