Siren
ALSIR-1408
Overview
:
Alarm
Preparation
:
1.
2.
3.
4.
Using screwdriver to turn anti-clockwise to remove two cover screws. ( Fig 1 )
Remove the top cover by sliding direction up. ( Fig 2 )
Install battery “ D “ type 4 pcs. ( Fig 3 )
Test Siren by one short press “ Learn “ button. Siren will be alarming accompany LED slowly blinking.
Again one short press “ Learn “ button to stop alarming immediately. ( Fig 4 ). Alarming and Alarm
flash will also stop automatically after 20 seconds without pressing “ Learn “ button .
5. Pair all “Triggers” 【 Magnetic Switch Transmitter, Motion Detector and Key chain】 with Siren.
Please refer to pairing procedure below for detail procedure first).
Fig 1
Fig 2
Fig 3
Fig 4
Version 1.
Pairing
:
 Pair Siren with Keychain Transmitter ( ALKCT ).
1. Press and hold Siren’s “Learn” button about 3 seconds till LED is slowly blinking to enter Learn mode.
Lean mode will be lasting 12 seconds then exit automatically.
2. Press both ALKCT “Arm“ and “ Disarm” buttons simultaneously about 3 seconds to enter Learn mode.
3. Press Arm button of keychain while Siren is in Lean mode to get pairing with each other.
Both Keychain and Siren LED will be quickly blinking 5 times to confirm paired successfully.
Press and hold
Press Arm and Disarm
Press Arm
 Test Key Chain (ALKCT) Function with Siren.
1. Press and hold ALKCT “Arm” button more than 1 second to enable siren to enter Arm mode,
ALCKT
red LED will lights ON for 1.5 second to confirm enter Arm mode.
2. Press and hold ALKCT “Disarm” button more than 1 second to disable siren arm mode, ALKCT
red LED will lights ON for 1.5 second to confirm exist Arm mode.
Arm
Disarm
 Pair Siren with Magnetic Switch Transmitter (ALMST).
1. Enter Learn Mode.
Press and hold Siren’s “Learn” button about 3 seconds till LED is slowly blinking to enter Learn
mode.
Learn mode will be lasting 12 seconds then exit automatically.
2. Using a small tool to press ALMST “ SET ” button about 3 seconds while Siren is in Learn mode then
ALMST will be paired with Siren. Both Siren’s and ALMST LED will be quickly blinking 5 times to
confirm paired successfully.
Enter and hold 3 second
to enter Learn Mode
Press and hold set for 3 seconds
Version 1.
 Test Magnetic Switch Transmitter (ALMST) Function with Siren,
 Enter test mode
1 : Short press MST “ Set “ button one time. ALMST LED will be slowly blinking.
2 : Place ALMST magnetic together with Switch Transmitter then apart magnetic from Switch
Transmitter more than 1cm, Siren will be flashing two times accompany two alert sounds.
3 : Place magnetic together with Switch Transmitter again, Siren will be flashing one time
accompany an alert sound.
4 : Repeat procedure 1 and 2 for more than two times to confirm ALMST is working with Siren.
 Short press “ Set “ again will stop LED blinking and exit test mode immediately. Test mode expire
automatically after 20 seconds .
Short Press Set
place together
Apart
Flash & Alert
>1cm
 Pair Motion Detector (ALMDT) with Siren
1. Press and hold Siren’s “ Learn ” button about 3 seconds till LED is slowly blinking to enter Learn
mode, Learn mode will be lasting 12 seconds then exist automatically .
2. Using a small tool to press and hold “ Set ” button than 3 seconds while Siren is in Learn mode to pair
with Siren. Both ALMDT LED and Siren’s LED will be quick blinking 5 times to confirm paired
successfully.
Enter Learn Mode
Press and hold Set for 3 seocnds
 Test Motion Detector (ALMDT) Function with Siren,
 Enter Test mode and test with follow steps.
1 : Short press MDT “ Set “ button one time, MDT LED will be slowly blinking.
2 : Wait for 25 seconds
3 : To turn Lens of MDT toward movement ( for example: to face user ) Siren
will be flashing two times accompany two alert sounds.
4 : Move Lens away from movement then to turn Lens to face movement again Siren be
flashing two times accompany two alert sounds again.
5 : Repeat above step 3 and 4 with same result that confirm MDT function is working.
Version 1.
 Short press “ Set “ again to exit test mode immediately. Test mode will be exit automatically
1 minutes later without pressing “ Set “.
Wait for 25 seconds
Installation
:
1. If all Triggers (Key China Transmitter, Magnetic Switch Transmitter, Motion Detector ) has already
been paired with Siren. Install Siren on the wall or at a flat surface. The “temper switch” located at
back side must be ensured pressed when placed on the wall. Fix Siren to wall or where you want it be
placed with screws, then slide the cover direction down after finishing all pairing.
2. Screw up case and tighten screws.
Version 1.
Un-Pairing :
Delete Siren’s all Pairs
Important notice :
All triggers has already paired with Siren must be deleted too once Siren all pairs be deleted.
Please refer to delete all Trigger’s pairing below first.
1. Press and hold “Learn” button about 3 seconds till LED is slowly blinking to enter “Delete” mode.
Delete mode will be lasting 12 seconds then exit automatically.
2. Release the pressing, then press Learn button again for more than 6 seconds till LED quick blinking,
3. Release the pressing again, then short press Learn button again LED will be quickly flashing 5 times
to
confirm all pairs is deleted.
Enter Delete
Release
Mode
Press and hold
Release
Short Press
6 seconds
Un-Pairing :
Delete Triggers all Pairs
 Delete ALMDT’s all Pairings
Press and hold “ Del” button more than 3 seconds till LED is slowly blinking to enter “Delete” mode. Release the pressing, then press “ Del ” button again for more than 6 seconds till LED quick blinking, Release the pressing, then short press “Del” button again to delete all pairs, LED will blinking 5 times to confirm has deleted all pairs. Enter Delete Mode
Release
Press & hold 6 seconds
Release
Short Press
 Delete ALMST all Pairings.
Press and hold “DEL” button about 3 seconds till LED is blinking to confirm in Delete mode. Release the pressing, then press “DEL” button again for more than 6 seconds till LED quick blinking, Release the pressing, then short press “DEL” button again to delete all pairs. ALMST LED will be quickly blinking 5 times to confirm successfully delete all pairs. Version 1.
Enter Delete Mode
Release
Press and hold Del
Release
Short Press
for 6 seconds
 Delete ALKCT all pairings.
Press both “Arm” and “ Disarm” buttons simultaneously about 3 seconds till LED is blinking to enter Learn mode. Release the pressing, then press “Arm” and “Disarm” buttons simultaneously again for more than 6 seconds till LED quick blinking, Release the pressing, then short press “ Disarm” button again to delete all pairs. LED will be quickly blinking to confirm all pairs has been deleted. Press
Arm& Disarm
Release
Pressing
Press Arm & Disarm
6 seconds
Release
Pressing
Short Press
Disarm
Un-Pairing :
Delete single Trigger Pairing
 Delete Keychain (ALKCT) Pairing from Siren.
1. Set both Siren and keychain to enter Learn mode. ( Refer to Pairing Section for detail )
2. Press ALCKT “ Disarm “ button to un-pair remote from Siren. Siren will be quickly
blinking 5 times to confirm successfully un-paired .
Enter Learn Mode
Enter Learn Mode
Press Disarm
 Delete Magnetic Switch Transmitter (ALMST) Pairing from Siren.
1. Press and hold Siren “Learn” button about 3 seconds till LED is slowly blinking to confirm enter
Learn mode. Learn mode will be lasting 12 seconds then exit automatically.
2. Press and hole MST “ DEL” button about 3 seconds while Siren is in Learn mode to un-pair ALMST
from Siren. Both Siren and ALMST LED will be quick blinking 5 times to confirm successfully
un-pairing.
Version 1.
Enter Learn Mode
Press and Hold DEL for 3 seconds
 Delete Motion Detector (ALMST) Pairing from Siren.
1. Press and hold Siren “Learn “button about 3 seconds till LED is slowly blinking to confirm enter
Learn mode. Learn mode will be lasting 12 seconds then exit automatically.
2. Press and hold ALMDT“DEL” button about 3 seconds while Siren is in Learn mode to un-pair
ALMDT from Siren. Both Siren and ALMDT LED will be quickly blinking 5 times to confirm success
un-pairing.
Enter Learn Mode
Press and Hold DEL for 3 seconds
Operation :
Arm :
Press and hold ALKCT “Arm” button more than 1 second to enable siren enter Arm mode, ALCKT red LED
will light ON for 1.5 second to confirm in Arm mode. If fail to enter Ar, Mode ALCKT LED will be
quick blinking for three times. Repeat pressing ALKCT Arm button to ensure Siren to enter Arm mode. Siren
will be ready for operation 75 seconds later after Siren entering into Arm mode.
Disarm :
Press and hold ALKCT Disarm button more than 1 second to disable siren arm mode, ALCKT red will light
ON for 1.5 second to confirm exist arm mode. If fail to exist Arm mode ALCKT LED will be quick blinking
for three times . Repeat pressing ALKCT “Disarm” button to ensure Siren exist Arm mode.
Arm
Disarm
Version 1.
Error notice : Alarming with Flashing light.
Siren will alarm warning alarm accompany flashing to indicate Siren or trigger is not installed when Siren
enter “Arm” mode. The warning alarm flashing will be lasting 20 seconds. But it can be terminated
immediately if press ALCKT “Disarm”. The error might caused by
1. Magnetic Switch Transmitter ( ALMST) is not closed. To check all ALMST ensure they are closed well.
Siren will warning alarm about 4 seconds later after it enter Arm mode.
2. Temper Switch of Motion Detector is out of working. Holder is not instead well to slot of Temper Switch
Siren will warning alarm immediately when enter Arm mode.
3. Siren Temper Switch is not pressed by wall and or slide cover of Siren is not placed well.
Siren will warning alarm immediately when enter Arm mode
4.
Press ALCKT ”Disarm” then check all installed triggers, magnetic switch, Motion Detector, if they are well
installed. Ensure window or door are closed then press “Arm” again to check if error can be free.
Repeat procedure of Disarm, Checking and Arm till Error notice is free.
Siren active and inactive.
Siren will be active once it receive trigger’s signal , such as ALMST ( magnetic switch ) ALMDT ( motion
Detector). Siren will alert alarming sound for 4 minutes once it be active. Press ALKCT disarm button to stop
alarming.
ALMST
ALMDT
Version 1.
Low Battery.
Two conditions to show Siren is low battery then it is needed to be replaced by new battery.
1).
Siren will start every 5 seconds 1 beep sound at the time after setting Siren into Arm or Disarm,
The beep sound will be lasting 3 minutes, total 36 beeps then stopping beep sound
2).
Siren LED start one blinking every 5 seconds and will keep blinking ( none stop) once Siren receive
trigger from triggers and active.
Specification :
number : ALSIR-1408
Radio frequency
Communication distance
Audible Alarm
Operation voltage
Battery
Battery Life
Battery low indicator
Dimension
Water proof
: 868.3 Mhz FSK two ways communication
: Min. 120M (Straight line open area)
: 100db @ meter
: 6V DC
: Alkaline D type 1.5V or LR20 x 4 pcs
: 18 months
: LED indicator with Bi sound.
: 248 x 170 x 70 mm ( LxWxH)
: IP44
Version 1.