LN10RWT / LN10RWL-20W
®
NXT
Wall Wash Trim Round
7
⁄8”
Regress
21⁄2” Ø
Plan View
LUMINAIRE INFORMATION
LIGHT ENGINE DELIVERED PERFORMANCE
20 Watts
NanoLED NXT
WALL WASH
80+
CRI
35
1250
725
Lumens per Watt
Source Lumens
Delivered Lumens
LN10RWT
315⁄16” Ø
90+
HIGH
CRI
29
1025
600
High power white LEDs tightly binned for fixture-to-fixture color
consistency within a 2-Step MacAdam Ellipse.
Standard CRI
2700K - 82+ CRI +/- 50K
3020K - 82+ CRI +/- 50K
3450K - 80+ CRI +/- 60K
High CRI
2700K - 90+ CRI
3020K - 90+ CRI
HEATSINK:
Proprietary high performance aluminum
heatsink for maximum LED life.
MATERIALS:
Trim: Precision die cast body with durable UV-stabilized
powder coating.
Trim Lens: Proprietary molded low iron lens.
Baffle Options: High temperature nylon.
BM - Black Matte Baffle
WM - White Matte Baffle
BV - Black Vertical Groove Baffle
WV - White Vertical Groove Baffle
BA - Black Alzak
MA - Matte Alzak
DRIVER: Field Replaceable
Solid state electronic. Constant current.
High power factor. Specify 120V or 277V.
Driver complies with IEEE C62.41 surge protection.
LIGHT ENGINE: Field Replaceable
14W and 20W Cree MT-G 2-Step. High power white LED's
tightly binned for fixture to fixture color consistency.
LISTINGS:
Dry/Damp
IBEW union made.
LN10RWL (Trimless)
NOTES:
• Maximum ceiling thickness up to 11/4"
See housing matrix on back for exceptions.
• Housing included with trim.
• Trimless for drywall installation only
• Trimless not available in acoustical ceilings.
• Fixture should be installed in applications
where ambient temperatures do not
exceed 40°C during normal operation.
• 5 year warranty
• Interior use only.
WALL WASH TRIM FEATURES
DIMMING: (optional)
Multiple dimming drivers available.
See compatibility chart attached.
High Performance
Heat Sink
CEILING CUT OUT:
31/2" Ø
Proprietary
Molded Lens
RATED LIFE: Based on IESNA LM80-2008
50,000 hours at 70% lumen maintenance (L70).
Die
Cast Body
Trim
Mounting Clips
HOW TO SPECIFY
Trim
–
Baffle Options
–
BM - Black Matte
(Trim)
Baffle
LN10RWT
(Trimless) WM - White Matte
Baffle
LN10RWL
BV - Black Vertical
Groove Baffle
WV - White Vertical
Groove Baffle
MA - Matte Alzak
BA - Black Alzak
®
USAI
–
Light –
Engine
–
–
MTG114 (14W LED)
MTG120 (20W LED)
www.usailighting.com
info@usailighting.com
Color
Temperature
– Trim Finish – Housing – Voltage –
–
Standard CRI 80+
27KS - 2700K-82 CRI
30KS - 3020K-82 CRI
35KS - 3450K-80 CRI
High CRI 90+
27KH - 2700K-90 CRI
30KH - 3020K-90 CRI
–
10 - White
21 - Black
28 - Metalized
Grey
RAL - Special
Color
–
LNC61
LNC63
LIC1
LIC3
LSH43
–
120V
277V
HOUSING DETAILS next page
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
Accessories
CB27 - 27" C-Channel
CB52 - 52" C-Channel
DIML2- 0-10V Low Voltage
15% Dimming Driver
DIML3- Lutron Hi-Lume LED /
ECO System Series "A"
2 Wire Control 1% Dimming Driver
DIML4 - Lutron Hi-Lume LED /
ECO System Series "A"
3 Wire Control 1% Dimming Driver
EML - Emergency lighting battery pack w/
remote test switch.
Above ceiling access required for service
EML not for use with IC/Airtight Housing
© 2012. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 3/29/12
LSH43
LNC61, LNC63
LIC1, LIC3
®
NXT
Housings for use with
NanoLED Wall Wash Trims - Round
HOUSING FEATURES
• Easy adjustment aperture plate that allows ceiling thickness adjustment from 7/8" to 11/2".
See housing matrix for details.
• Patent pending "Slide & Replace" easy driver replacement.
• Quick connectors on all wire connections.
• Universal housing style allows the ability to swap trim styles between Downlight, Adjustable and Wall Wash.
See Plug-and-Play limitations on matrix below.
• Fabricated of 20 ga. black powder coated steel with thru wire J-box, 2 in 2 out at min. 90°C, #12 AGW thru
branch circuit wiring.
LISTINGS:
Dry/Damp
IBEW union made.
NOTES:
• Maximum ceiling thickness 11/2".
See matrix for ceiling thickness options.
• Housing included with trim.
• Trimless for drywall installation only
• Trimless not available in acoustical ceilings.
• Fixture should be installed in applications
where ambient temperatures do not
exceed 40°C during normal operation.
• 5 year warranty
DRIVER: (Field Replaceable)
Solid state electronic. Constant current. High power factor. Specify 120V or 277V.
DIMMING: (optional)
3 wire dimming driver available. See compatibility chart attached.
MOUNTING:
Butterfly brackets and adjustable nailer bars with integral nails provided. Nailer bars are
extendible from 14" to 24" centers.
CEILING CUT OUT: 31/2" Ø
HOUSING INFORMATION - See limitations below
New Construction
New Construction
IC / Airtight
LSH43 - DL / ADJ / WW
(Max. Ceiling Thickness - 11/4")
LNC61 - DL / ADJ / WW
(Max. Ceiling Thickness - 7/8")
LIC1 - DL / ADJ / WW
(Max. Ceiling Thickness - 7/8")
LNC63 - DL / ADJ 30° / WW
(Max. Ceiling Thickness - 11/4")
LIC3 - DL / ADJ 30° / WW
(Max. Ceiling Thickness - 11/4")
41/2"
41/2"
63/4"
77/16"
131/4"
12"
51/4"
171/2"
163/8"
175/8"
Order housings with trims on reverse side.
®
USAI
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2012. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 3/29/12
®
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML2 & DIML3
NXT
DIMMING DRIVER WIRING SCHEMES:
DIML2 LED: 0-10V FL Dimming Driver Wiring
(Dims down to 15%)
Compatible Crestron Dimming System
NOTE: Consult dimmer manufacturer for detailed installation information.
NOTE: Consult dimmer manufacturer for detailed installation information.
For use with 0-10V fluorescent type controls.
Use only with approved vendor models:
Lutron: DIVA DVTV-XX
XX=Color
Leviton: IP710-DLX
Lightolier: V2000FAMU
0-10V
Dimmer
(By Others)
LED
0-10V VIOLET
CCT GREY
VIOLET
GREY
DIMMING
DRIVER
RED
BLACK
+
-
Creston
Model
Compatible
CLS-EXP-DIMFLV
DIN-4DIMFLV4
DIN-A08
GLX-DIMFLV8
GLXP-DIMFLV8
Y
Y
Y
Y
Y
Min # of
Creston
Measured
Fixtures Min-Max % Light Output
Required (1) Limits (2)
(3)
1
0-100%
15-100%
1
0-100%
15-100%
1
0-100%
15-100%
1
0-100%
15-100%
1
0-100%
15-100%
GROUND
WHITE
BLACK
(1) Operating dimmers with less than minimum required fixtures may cause flicker.
The Max number of fixtures is limited by dimmer rating unless otherwise noted.
(2) % Level refers to the Crestron Control System Intensity.
Operating the dimmer below the Min % level may cause flicker.
Operating the dimmer above the Max % may show no additional brightness.
(3) % Level of light output from fixture when connected directly to power source
(4) Dimmer requires a direct connection to neutral unless otherwise noted.
BUILDING POWER WIRING
NOTE GROUND WIRE
DIML3 LED: Lutron Hi-Lume A-Series 2 Wire Fwd Phase (with neutral) / LED Dimming Driver Wiring (Dims down to 1%)
Compatible Lutron Dimmers / Test Results
NOTE: Consult dimmer manufacturer for detailed installation information.
Product
Part Number
NovaT
Maestro Wireless
RadioRA 2 1000W
RadioRA 2 Adaptive dimmer
RadioRA 600W
RadioRA 1000W
HomeWorks QS 600W
HomeWorks QS 1000W
HomeWorks QS Adaptive dimmer
HomeWorks QS WPM
HomeWorks 600W dimmer
HomeWorks 1000W dimmer
HomeWorks WPM
GRAFIK Eye QS
GRAFIK Eye 3000
RPM-4U Module
(LCP, HomeWorks,
GRAFIK Systems, Quantum)
RPM-4A Module
(LCP, HomeWorks,
GRAFIK Systems, Quantum)
GP Panels
(LCP, HomeWorks,
GRAFIK Systems, Quantum)
Stanza
Fixtures Measured
Per Dimmer Light Output
120V Only* Range
NTLV-600-CPN0199
MRF2-6ND-120
RRD-10ND
RRD-6NA
RA-6ND
RA-10ND
HQRD-6ND
HQRD-10ND
HQRD-6NA
HQRJ-WPM-6D-120
1–8
1–8
1 – 13
1–8
1–8
1 – 13
1–8
1 – 13
1–8
1 – 11
(per output)
HRD-6ND
1–8
HWD-10ND, HRD-10ND
1–8
HWI-WPM-6D-120
1 – 10
(per output)
QSGR-, QSGRJ1 – 10
(per output)
GRX-3100, GRX-3500
1 – 10
(per output)
HW-RPM-4U-120,
1 – 26
LP-RPM-4U-120
(per output)
HW-RPM-4A-120,
LP-RPM-4A-120
1–8
(per output)
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
Compatible ETC Dimming Cabinets / Test Results
Approved for use with:
ETC Sensor + Cabinet with D20 dimming module
Measured light output 100% - 1%
ETC Unison DRd Cabinet with D20F dimming module
NOTE: Additional dim configuration required for optimum performance.
Measured light output 100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
Wire Diagram for 2-Wire Control
100% - 1%
100% - 1%
100% - 1%
Forward Phase
with Neutral
2-Wire Dimmer
(By Others)
LED
BLACK
SWITCHED HOT
WHITE
GREEN
NEU
GND
VV+
BLACK
RED
100% - 1%
DRIVER
(BACK SIDE OF
MTG PLATE)
Various
1 – 27
100% - 1%
SZ-6ND
1–8
100% - 1%
* Fixtures per Dimmer value assumes a 40W fixture. Number of fixtures may be higher
if wattage is less than 40W.
NOTE: Contact Lutron tech support for deganging rules when using wallbox controls on the
Hi-lume A-Series LED Driver.
®
USAI
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2012. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 3/29/12
®
DIMMING DRIVER COMPATIBILITY
SELECTION GUIDE
DIML4
NXT
DIMMING DRIVER WIRING SCHEMES:
DIML4 LED: Lutron Hi-Lume A-Series LED Driver with Eco System Control / LED Dimming Driver Wiring (Dims down to 1%)
Compatible Lutron Dimmers / Test Results
NOTE: Consult dimmer manufacturer for detailed installation information.
Product
Part Number
1-59
1-29
1-59
1-29
1-29
1-29
1-29
1-29
1-22
1-61
1-46
1-61
1-46
1-46
1-46
1-46
-
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
1-22
1-22
1-46
1-46
100% - 1%
100% - 1%
1-22
1-29
1-22
1-22
1-59
1-59
1-46
1-46
1-46
1-46
1-123
-
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% – 1%
100% - 1%
100% - 1%
BLACK
ORANGE
WHITE
GREEN
SWITCHED HOT
DIMMED HOT VV+
NEU
GND
E2
E1
BLACK
RED
DRIVER
(BACK SIDE OF
MTG PLATE)
ECO-SYS BUS
CAP WIRES
Wire Diagram for ECO System Digital Control
CAP LEAD
LED
ECO SYSTEM
Control
(By Others)
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
100% - 1%
BLACK
ORANGE
WHITE
GREEN
SWITCHED HOT
DIMMED HOT VV+
NEU
GND
E2
E1
BLACK
RED
DRIVER
(BACK SIDE OF
MTG PLATE)
PURPLE
32 per module
LED
FL
Control
(By Others)
PURPLE/GREY
64 per
EcoSystem
Wire Diagram for 3-Wire FL Control (no Eco System Control)
PURPLE
NTF-10,
NTF-103P, NTF-10-277
NTF-103P-277
NF-10
NF-103P, NF-10-277
NF-103P-277
VF-10
SF-10P, SF-103P
SF-12P-277,SF-12P-277-3
DVF-103, DVSCF-103P
DVF-103P-277,DVSCF-103P-277
AYF-103P
AYF-103P-277
VTF-6AM
MAF-6AM, MAF-6AM-277, MSCF6AM, MCSF-6AM-277
Maestro Wireless
MRF2-F6AN-DV
Spacer System
SPSF-6A,SPSF-6A-277, SPSF6AM, SPSF-6AM-277
Lyneo LX
LXF-103PL
Lyneo LX
LXF-103PL-277
Radio RA 2
RRD-F6AN-DV
HomeWorks QS
HQRD-F6AN-DV
Interfaces (1)
PHPM-3F -120, PHPM-3F-DV
NGRX-FDBI-16A
Energi Savr Node
CS-1L-WM, CS-2L-WM,
with EcoSystem
CS-1LCM, CS-2L-CM
Grafik Eye QS
QS with EcoSystem
with ECO System
Quantum
Quantum
PowerPak dim
RMJ-ECO32-DV-B
module ECOSystem
Measured
Light Output
Range
PURPLE/GREY
NovaT
NovaT
NovaT
Nova
Nova
Nova
Vareo
Skylark
Skylark
Diva
Diva
Ariadni
Ariadni
Vierti
Maestro
Fixtures
Per Dimmer
120V
277V
ECO-SYS BUS
(1) For use with 3 Wire controls or Commercial Systems, RA Systems or Home Systems applications.
*Contact Lutron tech support for deganging rules when using wallbox controls on the
Hi-lume A-Series LED Driver.
**Fixtures per Dimmer value assumes a 40W fixture. Number of fixtures may be higher if
wattage is less than 40W.
Compatible ETC Dimming Cabinets / Test Results
Approved for use with:
ETC Sensor+ Cabinet with D20 dimming module
Measured light output 100% - 1%
ETC Unison DRd Cabinet with D20F dimming module
NOTE: Additional dim configuration required for optimum performance.
Measured light output 100% - 1%
®
USAI
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2012. USAI, LLC.
All rights reserved.
All designs protected by copyright.
Revised 3/29/12
®
ColorPrecise Pro LED Module
™
NXT
USAI Interchangeable LED Light Engine
PERFORMANCE SUMMARY
14 Watts 20 Watts
®
NXT
PERFORMANCE
Lumens per Watt
Source Lumens
90+
90+
80+ HIGH 80+ HIGH
CRI CRI CRI CRI
87
875
Drive Current
71
715
350 mA
71
59
1250 1025
Light Engine
500 mA
SPECIFICATIONS
PHYSICAL DIMENSIONS
PHYSICAL CHARACTERISTICS
MODULE SOURCE TYPE: Field replaceable discrete LED light engine
utilizing CREE LEDs.
CONNECTION: Micro quick release connector with locking feature.
PROTECTION: Bidirectional 1500W transient voltage suppression.
CONSTRUCTION: Aluminum core board with integral thermal pad.
2-1/8" Ø
PHOTOMETRICS
COLOR CONSISTENCY: High power white LED tightly binned for fixture-tofixture color consistency within a 2-Step MacAdam Ellipse.
Standard CRI
High CRI
2700K - 82+ CRI +/- 50K
2700K - 90+ CRI
3020K - 82+ CRI +/- 50K
3020K - 90+ CRI
3450K - 80+ CRI +/- 65K
−
4000K - 80+ CRI +/- 70K
−
5/16"
NOTE:
LIGHT ENGINES ARE INCLUDED
WITH ALL
NanoLED NXT FIXTURES
COLOR RENDERING INDEX: >80 or >90.
COLOR RENDERING INDEX CONSISTENCY: +3 / -0 pts.
LIGHT ENGINE LIFE: Lumen maintenance L70/B50 50,000 hrs.
DIMMING: Multiple dimming options available. See fixture spec sheets.
COLOR CONSISTENCY
2-STEP
SPECTRAL DISTRIBUTION
3000K
LIGHT ENGINE REPLACEMENT
1.2
Spectrum
1.0
0.8
0.6
0.4
0.2
0.0
USAI Lighting Coordinates
380
500
600
Wavelength (nm)
700
2-Step MacAdam Ellipse for Fixture- NanoLED 3000K Spectral Power
to-Fixture Color Consistency
Distribution
OTHER
WARRANTY
REGULATORY: UL recognized. RoHS compliant.
MERCURY CONTENT: None.
UV OR IR CONTENT: None
5 year warranty.
®
USAI
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
800
Simple Light Engine Replacement
T 845–565–8500
F 845–561–1130
© 2012. USAI, LLC.
All rights reserved.
All designs protected by copyright.
USAI Lighting
LED Performance Summary
BeveLED2.0
16 Watts
BeveLED 2.0
DOWNLIGHT
Lumens per Watt
Source Lumens
Delivered Lumens (30°)
BEAM OPTIONS
10° 30°
50°
90+
HIGH
CRI
55
1165
900
80+
CRI
68
1425
1100
24 Watts
80+
CRI
64
1725
1525
COMPARED TO:
33 Watts
90+
HIGH
CRI
53
1410
1250
80+
CRI
63
2400
2100
32W CFL 42W CFL
90+
HIGH
CRI
52
1960
1720
82
CRI
39.3
2400
1404
90W PAR 38
HALOGEN SPOT
82
CRI
38.5
3200
1872
99
CRI
12.9
1310
1159
80°
COMPARED TO:
16 Watts
BeveLED 2.0
ADJUSTABLE
80+
CRI
Lumens per Watt
62
Source Lumens
1425
Delivered Lumens
1025
Center Beam Candle Power (10°) 14000
90+
HIGH
CRI
51
1165
835
11500
24 Watts
80+
CRI
59
1725
1400
19800
33 Watts
90+
HIGH
CRI
48
1410
1160
16000
80+
CRI
58
2400
1950
26970
90+
HIGH
CRI
48
1960
1600
22900
20W CMH 20W CMH 90W PAR 38
PAR 20 PAR 30 HALOGEN SPOT
81
CRI
39
1000
850
13000
81
CRI
46
1200
1020
19000
99
CRI
12.9
1310
1159
20000
BEAM OPTIONS
10° 30°
16 Watts
BeveLED 2.0
WALL WASH
90+
HIGH
CRI
43
1165
700
80+
CRI
52
1425
850
Lumens per Watt
Source Lumens
Delivered Lumens
24 Watts
80+
CRI
49
1725
1125
90+
HIGH
CRI
41
1410
1040
33 Watts
80+
CRI
49
2400
1635
90+
HIGH
CRI
43
1960
1435
SPACING CRITERIA
1.27
NanoLEDNXT
20 Watts
Downlight
NanoLED NXT
20 Watts
Lumens per Watt
Source Lumens
Delivered Lumens
Center Beam Candle Power (10°)
80+
CRI
49
1250
1000
90+
HIGH
CRI
40
1025
825
BEAM OPTIONS
25° 50°
Adjustable
80+
CRI
46
1250
952
8725
90+
HIGH
CRI
38
1025
780
7000
Wall Wash
80+
CRI
35
1250
725
USAI
99
CRI
18.25
912
804
9056
BEAM OPTIONS SPACING CRITERIA
10° 25°
1.27
®
www.usailighting.com
info@usailighting.com
90+
HIGH
CRI
29
1025
600
COMPARED TO MR16
50W MR16 SPOT
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2012. USAI, LLC. All rights reserved.
All designs protected by copyright.
Patent pending. CA-027 03/2012
®
BeveLED2.0
10° Beam
®
80+ CRI
90+ CRI
NXT
2-STEP
3000K
10° Beam
USAI Lighting
Coordinates