BRM1QS
indirect
Bruno
Specifications
5
DAY
Dimensions / Lamping
Construction — Nominal 8 1⁄4” x 1 3⁄4” rectangular housing is formed from cold-rolled steel.
Die-cast end caps are mechanically attached with no exposed fasteners.
1 3⁄4”
Reflectors — Die-formed specular reflector with 95% reflectance.
8 1⁄4”
Finish — Fine textured white polyester powder paint.
(1,2,3) T5, T5HO, or T8
Luminaire Length — 4’ 3⁄8”, 8’ and 12’ lengths in a single section for nominal support spacing at
4’, 8’ and 12’. For total luminaire length, add 5⁄8” for each flat end cap and 4” for each sculptured end
cap. Using internal joiners, 4’, 8’ and 12’ sections can be joined to form longer rows.
distribution — 0% downlight. See non-QuickShip spec sheet for photometrics.
SCEP option
Catalog Number
5
DAY
10
10
___________ ___________
___________
# of Lamps in Lamp Type
Cross Section
DAY
Luminaire
DAY
10
5 BRM1QS
5 10
Sample Catalog Number: BRM1QS 2 28 T5 SPR 24FT R8 120 GEB10 SCT LP835 F1/21 C210
BRM1QST
1
2
3
___________
Emergency Type1
___________
Reflector
28 T5 28W T5
SPR Specular
54 T5HO 54W T5HO
reflector
32 32W T8
___________
Switching
(Blank)None
SCT Single circuit
EC2Emergency
DCT2Dual circuit
circuit
ELEmergency
battery pack
EN2Emergency
battery pack
w/night light
circuit
___________
Luminaire Row
Length
___________
Maximum
Section Length
___________ ___________
Voltage
Ballast Type
___________
# of Emergency
Modules
X FT
(4’ increments)
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)
120
277
(Blank) None
1SE1 section
2SE2 sections
XSE X sections
GEB10<10% THD Electronic (all lamp types)
GEB10/347V 347V Generic non-dim. Only available with
10-day QuickShip
OS5COsram 0-10V dim or line voltage control (32 T8)
ADEZAdvance Mark 10 dim (54 T5HO)
OSDIMOsram 0-10V dim (54 T5HO)
ADZTAdvance Mark 7 0-10V dim (28 T5, 32 T8, 54 T5HO).
___________
Lamp Color
___________
Mounting Type /
___________
Overall Suspension3
___________
Finish
L/LP*No lamp
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI
*Wired for full wattage
lamps only, do not install
low wattage lamps
F1/T-bar ceiling (universal
mounting bracket)
F1A/T-bar ceiling (UMB with
integrated J-box)
F2/Hard ceiling (horizontal
J-box)
12 12”
C210White white
15 15”
(fine-textured
18 18”
low gloss)
21 21”
24 24”
XX XX”
Overall suspension is
measured from ceiling to
bottom of luminaire
___________
Options
ACGAdjustable cable grippers
CP
Chicago plenum (available with F1A only)
Dust cover
DU4
ELH
Emergency through wiring w/separate feed
Emergency through wiring w/single feed, shared neutral
ELS2
2
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR
Fusing (fast blow)
GMFFusing (slow blow)
MCSMatching feed canopy at support
OJB
Offset junction box
SCEPSculptured end cap
Notes: 1 Emergency type is installed in last 4’ of luminaire sections. Separate feed required unless ELS or ELS2 is specified 2 Not available with dimming 3 Maximum of 240” 4 Not available with 3 lamp 54 T5HO
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2014 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Bruno” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending.
Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx