iAdm8qs
Specifications
direct
IceTray Angular
with SBP
Dimensions / Lamping
Construction — Nominal 7” x 4” with extruded aluminum spine and nominal four 4’ one-piece
aluminum baffle assemblies. Steel and die-cast aluminum sculptured end cap.
with OPD
3 13⁄16”
Shielding — Straight blade baffles with perforated side reflector/shield or opal acrylic diffuser.
Reflectors — White painted center reflector (nominal 90% reflectance). Perforated side
reflector/shield.
7”
(1, 2) T5, T5HO or T8
Shown with SBP
Finish — White polyester powder paint standard.
3 13⁄16”
7”
(1) T5, T5HO or T8
Shown with OPD
Luminaire Length — 4’, 8’, and 12’ lengths in a single section for exact suspension spacing of
4’, 8’ and 12’. For total luminaire length, add 1 3⁄8” for each end cap. Using internal joiners 4’, 8’, and
12’ sections can be joined to form longer rows.
®
distribution — 100% downlight. See non-QuickShip spec sheet for photometrics.
Catalog Number
5
DAY
5
DAY
10
___________ ___________
Ceiling Type
DAY
Luminaire
10
DAY
10
5 IADM8QS
5 10
IADM8QST
(Blank) Suspended
S
Surface
mounted
___________
Emergency Type1
Sample Catalog Number:
___________
___________
# of Lamps in Lamp Type
Cross Section
1
2
IADM8QS 1 54 T5HO OPD 28FT R12 277 GEB10 SCT LP835 F1/24 C041 ACG
___________
Shielding
28 T5 28W T5
SBP
54 T5HO 54W T5HO
32 32W T8
OPD4
___________
Switching
(Blank) None
SCT S
ingle circuit
EC2Emergency
DCT2 Dual circuit
circuit
ELEmergency
battery pack
EN2Emergency
battery pack
w/night light
circuit
___________
Luminaire Row
Length
X FT
Side
(4’ increments)
perforated
shield
Baffle w/ opal
overlay
___________
Lamp Color
___________
Mounting Type
L/LP*No lamp
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI
*Wired for full wattage
lamps only, do not install
low wattage lamps
(Blank) Surface mounted
F1/T-bar ceiling
(universal mounting
bracket)
F1A/T-bar ceiling (UMB
with integrated J-box)
F2/Hard ceiling
(horizontal J-box)
/
___________
Maximum
Section Length
___________ ___________
Voltage
Ballast Type
R4
R8
R12
120
277
4’ section(s)
8’ section(s)
12’ section(s)
GEB10
<10% THD Electronic
(all lamp types)
GEB10/347V 347V Generic non-dim. Only
available with 10-day
QuickShip
OS5COsram 0-10V dim or line voltage
control (32 T8)
ADEZAdvance Mark 10 dim (54 T5HO)
OSDIM
Osram 0-10V dim (54 T5HO)
ADZT
Advance Mark 7 0-10V dim
(28 T5, 32 T8, 54 T5HO).
# of Emergency
Modules
(Blank) None
1SE1 section
2SE2 sections
XSE X sections
___________
Overall Suspension3
___________
Finish
___________
Options
(Blank)Surface mounted
12
12”
15
15”
18
18”
21
21”
2424”
XXXX”
Overall suspension is
measured from ceiling to
bottom of luminaire
C041White white
(low gloss)
ACGAdjustable cable grippers
CP
Chicago plenum (available with F1A only)
ELH
Emergency through wiring w/separate feed
2
Emergency through wiring w/single feed, shared neutral
ELS 2
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR
Fusing (fast blow)
GMFFusing (slow blow)
MCSMatching feed canopy at support
OJB
Offset junction box
Notes: 1 Emergency type is installed in last 4’ of luminaire sections. Separate feed required unless ELS or ELS2 is specified
3 Maximum of 240” 4 Not available with 2 lamp cross section
2 Not available with dimming
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending.
Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx