Operation Manual
Model: Wireless Socket Receiver Module
Wireless
Socket Receiver Module
Item
No.: WMR-3500
WMR-3500
Specification:
Function:
On / Off
Frequency:
433.92MHz
Remote distance: 50 meters (open field)
Input rating: 220-240V~50Hz
Output rating: 16Amps / 3500W (Resistive Load)
①
②
③
④
Neutral Wire – Blue
Neutral Wire – Blue
Switch Wire – Black
Live Wire – Brown
Dimension:
Overview:
Unique miniature high power (16A) receiver module that can replace existing house hold wired wall
socket into wireless remote controllable socket.
Small compact size for installation into wall box.
Unique Difference:

Current wall socket is wired with Live / Neutral / Earth directly into the socket terminal.

Adding extra receiver module to make your existing wall socket with wireless feature.
Wiring:
Before commencing work, ALWAYS isolate the mains power supply and switch off the circuit
breaker.
Strip the solid wires (rigid conductor only) at least 10mm then connect the wires as per diagrams
below, ensure terminals are properly tightened and no bare wire is visible.
Suitable wire size for terminal clamp is 1.6mm2 to 2.5mm2.
1. Remove current AC Live-in & Neutral-in wires from the wall socket terminals and leave wall
socket aside for later wiring (Section 6).
2. Connect AC Live-in & Neutral-in into each terminal clamp.
3. ①
②
Twist both terminal clamps to the side of module receiver.
Flip module around with back side facing towards you.
4. The antenna is located on the back side of receiver module.
To avoid interference of antenna reception do not cover receiver module with any bare wires.
5. Gently install receiver module into back box.
6. Connect AC Live-out & Neutral-out wires into wall socket terminals.
7. Tidy wires and install wall socket making sure no bare wires are in front of the module receiver.
8. Connect back mains power supply.
9. LED indicator will light ON for 10 seconds, this is to show you that the wires are connected
correctly and power is active.
10. To remove wires from terminal clamp, simply push back and pull out the wires

Each clamp has 2 terminals.
When the wires need to be looped, for example to another wall socket.
Install the wires shown in the below diagram.
Pairing:
Receiver module can pair with up to 6 different remote controls at any one time as it has a maximum
of 6 memories.
This receiver is not to be controlled by “Code Switch System” remote transmitters.
Only compatible to “Self Learning System” remote transmitters.
Pairing using LEARNING MODE:
1. On the receiver module press the ‘Learn’ button once, LED with flash. It is now in learning
mode.
2. Using a remote control press the ‘ON’ button intended to be paired; the LED will flash twice to
confirm that the remote control is now paired.
NOTE: Learning Mode lasts for 12 seconds; if no signal is received from a remote control during
this time then the receiver module will automatically exit learning mode without pairing the device.
！If, during learning mode the LED does not flash to confirm, this means that the receiver module’s
memory is FULL and no further remote control may be paired with it unless one of the existing
remote controls is first unpaired (see below).
Un-pairing:
Removing single Device:
1. On the receiver module press the ‘Learn’ button once, LED with flash. It is now in learning
mode.
2. Using a remote control press the ‘OFF’ button intended to be unpaired; the LED will flash twice
to confirm that the remote control is now unpaired.
Clearing Memory (will remove all paired remote controls):
1. On the receiver module press the ‘Learn’ button for 6 seconds (LED on receiver will flash),
release then press once again. The LED will flash twice to confirm that all remote control is now
unpaired.
Operation:
ON/OFF Function:
Press the ‘ON’ button on remote control, the lights will illuminate.
LED on receiver module will light ON for 1 second to indicate a signal is received from a remote
control transmitter.
Press the ‘OFF’ button on remote control, the light will turn OFF.
LED on receiver module will light ON for 1 second to indicate a signal is received from a remote
control transmitter.
！During standby mode, LED on receiver module will not illuminate.
Caution:
Please leave minimum of 1.5 meters in-between 2 or more receivers.
When inserting module into back box make sure excess wires do not cover module’s back side. This
may reduce the antenna reception distance.
Troubleshoot:
Problem:I cannot pair my remote control with the receiver module.
Solution: The memory on receiver is full, please delete one or more memory and try pairing again.