Wireless Receiver Module for Wall Outlet
A high power (16 A) receiver module that is relatively easy to fit behind an
existing wall outlet in order to turn the entire wall outlet into a wireless On/Off
function. Can be controlled by all self learning transmitters in System Nexa and
the System Nexa Pro series.
Small and compact, suitable for permanent installation in mounting box
Why WMR-3500 is unique
The wiring of the current wall outlet is wiring the Earth / Live-in / Neutral-in
directly into the socket terminal.
This module adds another wireless feature while keeping your existing wall outlet.
The receiver module comes with 2 wires with terminal connector (Live / Neutral)
so no need to prepare additional wires during installation.
Specification
Wiring
Before commencing work, ALWAYS isolate the mains power supply and switch
off the main switch.
Strip the solid wires (rigid conductor only) at least 10mm then connect the wires
as per diagrams below, ensure terminals are properly tightened and no bare wire is
visible.
Suitable wire size for terminal: 1.6mm2 to 2.5mm2.
Remove current AC Live-in / Neutral-in wires / Earth wires from the socket block
terminals
Connect AC Live-in / Neutral-in into terminal connector making sure it’s inserted
correctly.
Tidy terminal connector and place into wall box.
Connect AC Live-out / Neutral-out into socket terminals.
！Please leave the Earth wires until step D.
Tidy wires and insert the module into wall box. Connect the earth wires into
socket earth terminal.
Connect back mains power supply.
LED indicator will light ON for 10 seconds, this is to show you that the wires are
connected correctly and power is active.
To remove wires from terminal connector, simply push back and pull out the
wires.
Each connector have 2 terminals, both terminal can be used depending on your
4
current wiring at home.
Single AC Live-in / Neutral-in
Twin AC Live-in / Neutral-in
Programming
The receiver module can pair with up to 6 different remote controls at any one time
as it has a maximum of 6 memories.
This receiver cannot be controlled by “Code Switch System” remote transmitters.
Only compatible with “Self Learning System” remote transmitters. / Self learning
transmitters and Nexa Gateway.
Programming using LEARNING MODE:
On the receiver module press the ‘Learn’ button once, red LED with flash. It is
now in learning mode.
Using a remote control press the ‘ON’ button intended to be paired; the load/light
will flash twice to confirm that the remote control is now paired.
NOTE: Learning Mode lasts for 12 seconds; if no signal is received from a remote
control during this time then the receiver module will automatically exit learning
mode without pairing the device.
！If, during learning mode the LED does not flash to confirm, this means that the
receiver module’s memory is FULL and no further remote control remote controls
may be paired with it unless one of the existing remote controls is first unpaired
(see below).
Un-pairing
Removing single Device:
On the receiver module press the ‘Learn’ button once, red LED with flash. It is
now in learning mode.
Using a remote control press the ‘OFF’ button intended to be unpaired; the load/
light will flash twice to confirm that the remote control is now unpaired.
Clearing Memory (will remove all paired remote controls):
On the receiver module press the ‘Learn’ button for 6 seconds (LED on receiver
will flash), release then press once again. The load/light will flash twice to confirm
that all remote control is now unpaired.
Operation
ON/OFF Function:
Press the ‘ON’ button on remote control, the lights will illuminate.
Red LED on receiver module will light ON for 1 second to indicate a signal is
received from a remote control transmitter.
Press the ‘OFF’ button on remote control, the light will turn OFF.
Red LED on receiver module will light ON for 1 second to indicate a signal is
received from a remote control transmitter.
！During standby mode the Red LED on receiver module will not illuminate.
Caution:
Please leave minimum of 1.5 meters in-between 2 or more receivers.
5
Specification:
RF frequency: 433.92 MHz
Input rating: 220-240V~50Hz
Output rating: 16Amps / 3500W (Resistive Load)
Standby power consumption: Below 1W.
HYPERLINK "http://www.nexa.se"
www.nexa.se
HYPERLINK "mailto:support@nexa.se"
support@nexa.se
6