vendor item control drawing

advertisement
CAGE CODE 0WY55 DWG NO. 2200476
APPLICATION
NHA
USED ON
2320255
WSR-88D
2320256
LTR
DATE
A
130702
B
130722
SHEET 1 OF 3
ECO ECP
ECP 0437
ECO A05737
ECP 0437
ECO A05742
REVISION DESCRIPTION
APVD
INITIAL RELEASE AT REV A
RSS
ADD -202 AND -203 CONFIG
RSS
VENDOR ITEM CONTROL DRAWING
DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
TOLERANCES ON:
MILLIMETERS
INCHES
1 PL 
2 PL  .06
2 PL 
3 PL 
ANGLES  2
APPROVALS
DWN
AWB 130702
CHK
BOB 130702
ENGR RSS 130702
QA
RMT
DOC
CM
ROC
WSR-88D RADAR OPERATIONS CENTER
3200 MARSHALL AVENUE
NORMAN, OKLAHOMA 73072-8032
NOMENCLATURE
SLEEVING, NYLON, EXPANDABLE, BRAIDED
JBM 130702
RJG 130702
SIZE
A
CAGE CODE
0WY55
SCALE: NONE
DWG NO.
2200476
REV
B
SHEET 1 OF 3
CAGE CODE 0WY55 DWG NO. 2200476
SHEET 2 OF 3
GENERAL NOTES:
1.
INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.
1.1.
IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS
SPECIFICATION IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY
AS A SOURCE OF SUPPLY FOR THE ITEM(S).
1.2.
THE USE OF A DIFFERENT PART FROM A LISTED SUGGESTED SOURCE OF SUPPLY OR A PART FROM A
NON-LISTED SUGGESTED SOURCE OF SUPPLY WHICH MEETS THE SPECIFICATIONS HEREIN SHALL
OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR88D RADAR OPERATIONS CENTER (ROC) AS WELL AS ACCEPTANCE INSPECTION BY THE NATIONAL
RECONDITIONING CENTER (NRC).
2.
REQUIREMENTS:
2.1.
SLEEVING: NYLON 6-6 POLYAMIDE MONOFILAMENT
2.1.1.
NOMINAL INSIDE DIAMETER: SEE TABLE II
2.1.2.
NOMINAL EXPANDED INSIDE DIAMETER: SEE TABLE II
2.1.3.
SLEEVING LENGTH: PER TABLE II
2.2.
ENVIRONMENTAL:
2.2.1.
OPERATING TEMPERATURE: +10º C (+50° F) TO +49º C (+120° F)
2.2.2.
NON-OPERATING TEMPERATURE: -35º C (-31°F) TO +60º C (+140° F)
2.3.
RELIABILITY:
2.3.1.
MTBF: N/A
2.4.
PART IDENTIFICATION:
2.4.1.
VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR. PART NUMBER
MAY BE APPLIED TO PACKAGING.
3.
PROCURING AGENCY:
3.1.1.
THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED
NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.
4.
THE PART NUMBER IS THE DRAWING NUMBER SUFFIXED WITH THE APPLICABLE DASH NUMBER
SHOWN IN TABLE II.
SIZE
A
CAGE CODE
0WY55
SCALE: NONE
DWG NO.
2200476
REV
B
SHEET 2 OF 3
CAGE CODE 0WY55 DWG NO. 2200476
5.
SHEET 3 OF 3
SUGGESTED SOURCE(S) OF SUPPLY (MANUFACTURER(S)):
ELECTRIDUCT INC
FORT LAUDERDALE, FL
PART NO.: PER TABLE II
(CAGE CODE: 4J4R6)
TABLE II
6.
DASH
NO.
SPC TECHNOLOGY
PART NO.
NOMINAL
DIAMETER
201
202
203
BSNY-075-75
BSNY-050-100
BSNY-025-200
.75
.50
.25
EXPANSION RANGE
EXPANSION
MIN
.50
.37
.12
EXPANSION
MAX
1.25
.75
.38
SLEEVING
LENGTH
75 FT ± 5 FT
100 FT ± 5 FT
200 FT ± 5 FT
FIGURES AND DIAGRAMS
FIGURE 1
SIZE
A
CAGE CODE
0WY55
SCALE: NONE
DWG NO.
2200476
REV
B
SHEET 3 OF 3
Related documents
Download