Now with a 15 year guarantee

advertisement
Q U I C K
C H E C K
Exterior
Water Wash Up
Roller, Brush or Spray
Recoat – 2 hours
Now with a 15 year guarantee
GENERAL DESCRIPTION
A Ultra Premium high quality self-priming,
exterior grade 100% acrylic finish. That is
durable, UV resistant and long lasting.
USES
As a high quality low sheen finish for a wide
variety of substrates including timber, masonry,
brick, cement render and also on primed metal.
Also suitable for roofing.
This product is not suitable for use where
painted surfaces are in contact such as door
and window frames. Haymes Ultratrim
products are suitable in these areas.
COLOURS
Available in a range of bases which allow
machine tinting to a wide range of popular
colours or choose from a limited range of
factory milled colours. Bases available are
Blue, Dark, Green, Mid Tone, Red, Red Oxide,
Ultra Deep, Yellow Oxide, Extra Dark, Orange
Extra, Yellow Extra and White. Milled Colours
are Black and Mission Brown.
SIZES
White available in 1 litre, 2 litre, 4 litre, 10 litre
and 15 litre, white tint bases available in 1 litre,
2 litre, 4 litre and 10 litres, coloured tint bases
available in 1 litre, 2 litre and 4 litre (orange
and yellow extra tint only available in 2 litre and
4 litre).
COVERAGE
Up to 16 square metres per litre depending
upon surface porosity and application method.
APPLICATION
Roller, brush or spray.
PROVIDE ADEQUATE VENTILATION
DURING USE.
DRYING TIMES
Touch Dry Time - 30 minutes.
Recoat Dry Time - 2 hours.
Drying times refer to normal conditions (25°C,
50% humidity). Under cooler, humid or still
conditions, longer drying times may be
necessary.
SURFACE PREPARATION
Previously Painted Surfaces:
Scrape off all loose and flaking paint and make
sure any remaining paint is firmly attached to the
surface, sand scraped edges smooth. Sand all
gloss and semi gloss finishes to a dull finish,
remove all chalky paint by sanding. Wash with
Haymes Unikleen diluted with water to remove all
dirt, grease and mould. For severe mould growth
clean with a 10% hypochlorite bleach solution.
Rinse with clean water. Fill nail holes, cracks
and imperfections with Haymes Unifill (not
Haymes linseed Oil Putty). Sand smooth and
dust down. Prime metal areas with the
appropriate primer. Any areas of greyed timber
should be sanded back to sound timber and spot
primer with Haymes Wood Primer White of
Haymes Acrylic Timber Primer. Apply one coat
of Haymes Tricoat to old enamel paint.
New Timber:
Fill imperfections with Haymes Unifill (not
Linseed Oil Putty). Apply three coats of
Haymes Low Sheen Solashield. For tannin rich
timbers apply one coat Acrylic Timber Primer
or White Wood Primer.
Preprimed timber: Use of pre-primed timber is
becoming more common for exterior use.
These primers are of variable quality and while
some are high quality primers ready for the
application of finishing coats, some are
intended only as temporary coatings during the
construction period and are not suitable for
painting. Haymes recommend removal of
the primer before application of finish coats. To
determine if the primer is suitable for painting
test the adhesion of the primer to the timber.
Cut a small “x” through the existing coating
with a sharp blade. Press adhesive tape firmly
across the cut and then rip off the tape. If any
of the existing coating comes off it is unsound
and must be removed by sanding. If in any
doubt sand the surface before painting.
Masonry, Fibro, Brick:
Fill imperfections, with Haymes Unifill, sand
smooth and dust down. Apply Haymes Low
Sheen Solashield directly to surface.
Galvanised Iron:
Degrease new galvanised iron. Weathered (no
shine) galvanised iron with a mild detergent
solution and rinse with clean water. Apply one
coat of Haymes Acrylic Galvanised Iron Primer
to weathered galvanised iron to guard against
white rust. Allow 4 hours before re-coating.
Note: this product is not suitable for paving
or contact surfaces.
New Steel. Wrought Iron:
Remove all rust by scraping, sanding or using
Haymes Derustit. Apply two coats of Haymes
Metal Primer Grey allowing 16 hours to dry
between coats.
Roofing:
Prepare surfaces according to label
instructions for pre-painted surfaces or
galvanised iron. Remove all rust by scraping
and sanding. Treat rust areas with Haymes
Derustit. If collecting rainwater disconnect
pipes for TWO good Rains.
FINISHING
Apply two coats of Low Sheen Solashield.
THINNING & CLEAN UP
May be thinned with up to 100ml of water per
litre for first coat on porous surfaces. Apply
subsequent coat/coats unthinned. Clean
equipment with water immediately after use.
PAINTING CONDITIONS
OPTIMUM APPLICATION CONDITIONS ARE
10°C TO 30°C. For application under warmer
conditions please refer to thinning advice.
While in hot weather, avoid painting in direct
sunlight. Very warm or porous surfaces may be
dampened with clean water prior to application
of Haymes Low Sheen Solashield. Avoid
applying externally in late afternoon in winter or
in doubtful weather as frost, dew or rain is likely
to impair gloss or durability of the coating.
STORAGE
Protect from extremes of temperature. Store
between 5°C and 30°C.
WARRANTY
Haymes guarantees Solashield will not flake,
blister or peel for 15 years. For this warranty to
apply Solashield must be applied to correctly
prepared surfaces. This warranty does not
cover failure caused by the breakdown of any
previous coatings. Haymes will supply paint to
recoat affected areas should the product not
perform as specified above.
PRECAUTIONS
•
Safety Directions: Keep out of reach of children. Avoid contact with skin and eyes and
inhalation of vapours. Wear suitable protective clothing, eye protection and impervious gloves
when mixing and using. Handling and usage of this product must be carried out under well
ventilated conditions that prevent inhalation of vapours.
•
First Aid Instructions: If affected by inhalation, remove to fresh air. If breathing difficulty
persists or occurs later, consult a doctor. If swallowed, drink plenty of water and seek
immediate medical advice. Contact a doctor or Poisons Information Centre (Phone 13 1126). If
skin contact occurs, remove contaminated clothing and wash skin thoroughly with soap and
water. If irritation occurs seek prompt medical advice. In case of eye contact, hold eyes open
and flush with running water for at least 15 minutes and seek medical advice.
NOTE: Further information is available in the form of Material Safety Data and Product
Information Sheets from your local Haymes Paint Distributor or Freecall Haymes Paint on 1800
033 431. We are continually updating materials and methods, so please ensure you have the
latest information
•
Protect Our Environment: In case of spills shut off all ignition sources. Contain or shut off
leak if safe to do so. For large spills use respiratory protection, protective apparel and
footwear. Spills should be absorbed either with rags (small spill) or dry sand/earth (large spill).
Ensure paint does not get into gutters or drains. Retain in a marked sealed container for future
use or disposal via special chemical waste collection programs. Dried empty containers can be
recycled and should be disposed of via council recycling facilities. Do not re-use empty
containers.
For best results, preparation is vitally important when repainting. Always ensure that the adhesion
of old paint is sound before proceeding.
For further information or to place an order, call
Service Express direct: Phone - 1800 033 431
or email - info@haymespaint.com.au
Download