12V 300W CLASS 2 Dimmable Driver CLASS 2 UL 1310

advertisement
12V 300W CLASS 2 Dimmable Driver
This driver is to be installed in accordance with Article 450 of the
National Electric Code (NEC). This driver must be installed in a
well-ventilated area free from explosive gases and vapors. Proper
operation requires the free flow of air. As this transformer is hardwired, it should only be installed by a qualified electrician.
READ ALL INFORMATION PRIOR TO INSTALLATION
TECHNICAL SPECIFICATIONS
Rated Wattage:
300W
Enclosure:
Steel, powder coated
Input Voltage:
120V AC
Frequency:
60Hz
Input Current:
2.8A , maximum no load input
current: 0.6A
Output Voltage:
Without Boost: 11.6V DC
With Boost: 12.6V DC
Output Power:
6 Circuits 12V DC @ 50W / 4.2A
Environment:
Indoor only
Working Temperature:
Enclosure temperature does not
exceed 70º C in a 40º C ambient,
fully loaded.
Ambient Operating
Temperature:
-20º C ~ 40 º C
7”
INSTALLATION & WARNING
• This driver is for indoor use ONLY.
• Shut off power at the main breaker before attempting installation.
• For use with an ON/OFF switch or a compatible Magnetic Low
Voltage (MLV) dimmer switch. Visit the online page of this product
for a detailed list of compatible dimmers.
• Once installation is complete, turn on power at the main breaker.
3.2”
DIMMABLE SETUP
• ONLY use recommended 120V MLV Dimmers. Please visit the
online product page for a detailed list of compatible dimmers.
• Dimmers may vary in function. Always review dimmer manufacturer
instructions for proper installation and use.
7”
MOUNTING
• Driver must be mounted in a dry location with adequate airflow.
• N.E.C. requires all drivers to be grounded to the GREEN grounding
wire.
KNOCKOUTS
• Four 1/2” NPT Knockouts are featured on these dimmable drivers
• Remove wiring knockouts as needed and install 1/2” Romex
connectors or bushings to reduce wire strain.
UL 1310
CLASS 2
Wiring Diagram
The orange Boost Tap is an optional voltage boost recommended for use with a MLV dimmer, as most MLV dimmers cut down voltage by 10%.
Additionally, if the fixture is receiving 10.5V or less in an ON/OFF switch installation, the orange Boost Tap is recommended.
On/Off Switch : Wiring without Boost Tap
MLV Dimmer : Wiring with Boost Tap
Leave the end cap on the orange wire.
White and Black wires only.
120V AC
Power
N
N
L
H
Screw the end cap on the Black wire.
White and Orange wires only.
120V AC
Power
H
L = Line (Black)
N = Neutral (White)
H = Hot (Black)
= Ground (Green)
B = Boost (Orange)
3
4
5
6
– 1 +
– 4 +
v–
LED Fixture
– 2 +
– 3 +
– 5 +
– 6 +
H
CLASS 2
L = Line (Black)
N = Neutral (White)
H = Hot (Black)
= Ground (Green)
B = Boost (Orange)
Dimmable LED Fixture
v+
LED Fixture
H
B
120V AC Magnetic
Low Voltage Dimmer
v+
v–
L
N
B
2
N
N
120V AC
ON/OFF
Switch
1
N
Dimmable LED Fixture
1
2
3
4
5
6
– 1 +
– 2 +
– 3 +
– 4 +
– 5 +
– 6 +
v–
CLASS 2
v+
v–
v+
3-Way Dimmer Application
Compatible 3-way 120V MLV dimmers ONLY are recommended to be
installed with 3-way applications. Visit the online page for this product
for a detailed list of compatible dimmers.
120V AC
Power
N
N
L
H
Troubleshooting
N
Traveling
Lines
120V AC Magnetic
Low Voltage 3-Way
Dimmer
H
B
3-Way On/OFF
Switch
L = Line (Black)
N = Neutral (White)
H = Hot (Black)
= Ground (Green)
B = Boost (Orange)
1
2
3
4
5
6
– 1 +
– 2 +
– 3 +
– 4 +
– 5 +
– 6 +
v–
v+
Dimmable LED Fixture
v–
Dimmable LED Fixture
v+
CLASS 2
Lights are non functional.
Make sure 120V AC Breaker is in the ON position
Use a multimeter to check DC output voltage at the lighting source.
If lights remain unresponsive, confirm the following:
• Wire polarity
• Accessories and accessory placement.
Lights are not dimming or flickering.
1. Confirm a compatible 120V MLV dimmer switch has been installed
between the AC line voltage and dimmable driver. Visit the online
page for this product for a detailed list of compatible dimmers.
2. Check that the 12V DC light fixture installed is rated as a dimmable
LED Fixture.
Download