Analog Timer

advertisement
Analog Timer
TTL Series
Part Number Description
TTL
-
❶
❷
❸
❶ Pin Type
8 : 8Pin Socket and Panel mounted
❷ Timing Mode
A : A, A1, F1, I
B : A, A1, B, F
❸ Supply Voltage
110/220VAC
24VDC
110VDC
General Specification
Model Name
TTL-8A, TTL-8B
Function
Multi Timer
Timing Range
0.05sec ~ 100hour (Max. hours)
Rated Supply Voltage
100-240VAC 50/60Hz, 24VDC, 110VDC
Operating Voltage Range
90 ~ 110% of the Supply Voltage
Power Consumption
Approx. 4.5VA (220VAC 60Hz)
Approx. 1.5W (24VDC)
Approx. 2.2W (110VDC)
Recovery Time
Max. 200ms
Control
Output
Life Cycle
Contact Form
Output by the Output Operation Mode, Temp (2C)
Select Among Order (1C) + Temp (1C)
Contact Capacity
NO : 250VAC 3A Resistance Load
NC : 250VAC 2A Resistance Load
Mechanical
Min. 10,000,000
Electrical
Min. 100,000
Accuracy of operating time
Max. ±0.3% FS
Setting Error
±5%
Influence of Voltage
Max. ±0.5% FS
Influence of Temperature
Max. ±2% FS
Insulation Resistance
100MΩ (for 500VDC)
Dielectric Resistance
For 1 Minute Under 2000VAC 50/60Hz
Noise Immunity
The Wave Form Noise (pulse 1us) ±2kV by the Noise Simulator
Vibration
Resistance
Shock
Resistance
Malfunctional
10-55Hz(1 Minute Duration) Dual Wave Length 0.5mm 10 Minutes for Each Direction of X, Y, Z
Destruction
10-55Hz(1 Minute Duration) Dual Wave Length 0.75mm 1 Hour for Each Direction of X, Y, Z
Malfunctional
100m/s2 (10G) Three Times for Each Direction of X, Y, Z
Destruction
300m/s2 (30G) Three Times for Each Direction of X, Y, Z
Ambient Temperature
-10 ~ +55°C (with no icing)
Storage Temperature
-25 ~ +65°C (with no icing)
Ambient Humidity
35 ~ 85%RH
Weight
Approx. 100g (Except For The Packaging Material)
Ⅲ - 46
Industrial Controls Catalog
www.kacon.co.kr
Rev. 2/14
Data subject may change without notice.
Data Processing
Product Selection
Timing Mode
Part Number
A, A1, F1, I
TTL-8A
Voltage
TTL-8A 110/220VAC
TTL-8A 24VDC
TTL-8A 110VDC
TTL-8B 110/220VAC
A, A1, B, F
TTL-8B
TTL-8B 24VDC
TTL-8B 110VDC
Time Range
Time Unit
Setting Time Range
Time Range
0.05 ~ 0.5
0.5
0.1 ~ 1.0
1.0
0.5 ~ 5
5
10
1 ~ 10
10
1 ~ 10
0.5
0.05 ~ 0.5
0.5
0.05 ~ 0.5
0.1 ~ 1.0
1.0
0.5 ~ 5
5
1 ~ 10
10
0.5
1.0
5
1.0
5
sec
min
10
Time Unit
Data Processing
Time Range
Setting Time Range
0.05 ~ 0.5
0.1 ~ 1.0
hour
0.5 ~ 5
0.1 ~ 1.0
10h
0.5 ~ 5
1 ~ 10
Diagram
TTL-8A, TTL-8B
[A], [F] output operation mode
[A1], [B], [F1], [I] output operation mode
contact:
contact:
Resistive Load
Resistive Load
source
source
Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr
Industrial Controls Catalog
Ⅲ - 47
Analog Timer
TTL Series
Timer Function
Power Indicator / Output Indicator
(On-Delay NO Contact Operation : Green
On-Delay NO Contact Open : Orange)
Operation Mode Selector
Operation Mode Display Window
TTL-8A (A, A1, F1 and I mode)
Time Setting Knob (Set Time)
TTL-8B (A, A1, B and F mode)
Time Range Selector
Time Unit Display Window
(sec, min, hour, 10h)
Time Unit Selector
☞ Rotate the time unit shift switch and operation mode shift switch clockwise.
☞ Time range shift switch cannot be rotated below 0.5 and above 10. Do not forcefully rotate the switch.
Dimension
(mm)
Panel
Socket : K2BF08
Output Operation Mode For Each Model
TTL-8A
TTL-8B
Indication
Operation Mode
Indication
Operation Mode
A
Power on Delay
A
Power on Delay
A1
Power on Delay 1
A1
Power on Delay 1
F1
Flicker (ON)
B
Power on Delay 2
I
Interval
F
Flicker (OFF)
Ⅲ - 48
Industrial Controls Catalog
www.kacon.co.kr
Rev. 2/14
Data subject may change without notice.
Data Processing
Timing Charts (TTL-8A, TTL-8B)
■ : Indication Lamp (Green), ▨ :Indication Lamp (Yellow), t : Configured time, t>t-a Rt: Returning time (100ms lower)
Mode
Time Table
A
power on
delay
power source 2-7
time delay NC 1-4
(8-5)
time delay NO 1-3
(8-6)
power/output Indication LED
A1
power on
delay 1
time delay NO 8-6
0.5sec
Data Processing
(One-shot output)
power source 2-7
time delay NC 8-5
0.5sec
instantaneous NC 1-4
instantaneous NO 1-3
power/output Indication LED
B
power on
delay 2
power source 2-7
time delay NC 8-5
time delay NO 8-6
instantaneous NC 1-4
instantaneous NO 1-3
power/output Indication LED
F
flicker
(OFF start)
power source 2-7
time delay NC 1-4
(8-5)
time delay NO 1-3
(8-6)
power/output Indication LED
F1
flicker 1
(ON start)
power source 2-7
time delay NC 8-5
time delay NO 8-6
instantaneous NC 1-4
instantaneous NO 1-3
power/output Indication LED
I
interval
power source 2-7
time delay NC 8-5
time delay NO 8-6
instantaneous NC 1-4
instantaneous NO 1-3
power/output Indication LED
☞ In the F or F1 output operation mode, an extremely short time setting may lead to abnormal output operation due to the contact output response time. The minimum time setting must be 100 ms.
Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr
Industrial Controls Catalog
Ⅲ - 49
Analog Timer
TTL Series
Part Number Description
TTL
-
❶
❷
❶ Function
SD: Star-Delta operation
❷ Supply Voltage
100/240 VAC
General Specification
Model Name
TTL-SD
Function
Star - Delta TIMER
Timing Range
0.05sec ~ 100sec (Maximum hours)
Rated Supply Voltage
100/240VAC 50/60Hz
Operation Voltage Range
90 ~ 110% of the Supply Voltage
Power Consumption
approx. 4VA(240VAC 60Hz)
Recovery Time
Max. 100ms
life cycle
Y
Control
Output
Contact Form
Contact Capacity
250VAC 3A Resistance Load
Mechanical
Min. 10,000,000
Electrical
Max. 100,000 (250VAC 3A Resistance Load)
contact : SPST (1N/O), △ contact : SPST (1N/O)
Repetition Tolerance
Max. ±0.3%
Setting Error
±5%
Influence of Voltage
Max. ±0.5%
Influence of Temperature
Max. ±2%
Shift Time Tolerance
±25%
Insulation Resistance
100MΩ (for 500VDC)
Dielectric Resistance
2000VAC 50/60Hz for 1 minute
Noise Immunity
the wave form noise (pulse 1us) ±2kV by the noise simulator
Vibration
Resistance
Malfunctional
10-55Hz(1 Minute Duration) Dual Wave Length 0.5mm 10 Minutes for Each Direction of X, Y, Z
Destruction
10-55Hz(1 Minute Duration) Dual Wave Length 0.75mm 1 Hour for Each Direction of X, Y, Z
Shock
Resistance
Malfunctional
100m/s2 (10G) Three Times for Each Direction of X, Y, Z
Destruction
300m/s2 (30G) Three Times for Each Direction of X, Y, Z
Ambient Temperature
-10 ~ +55°C (with no icing)
Storage Temperature
-25 ~ +65°C (with no icing)
Ambient Humidity
35 ~ 85%RH
Weight
Approx. 100g (except for the packaging material)
Product Selection
Ⅲ - 50
Dimension
[Panel processing dimension diagram]
Operating
Mechanism
Part Number
Analog Timer
TTL-SD
Industrial Controls Catalog
(mm)
Panel
socket : K2BF08
www.kacon.co.kr
Rev. 2/14
Data subject may change without notice.
Data Processing
Diagram
Timer Function
Contact:
250VAC 3A Resistive Load
Star Operation Indication
Delta Operation Indicator
Time Setting Knob
Time Switch Knob
A: 50ms
B: 100ms
C: 250ms
D: 500ms
Scale Time Range Display Window
source
(T1)
source
Star Operation Time Range Selector
Star-Delta Transfer Time Selector (T2)
Time Range
1. T1(Time Setting) Specification
Time Range
Time Unit
Setting Time Range
5
0.5 ~ 5 sec
1 ~ 10 sec
x10sec
Time Switch Display
A
B
C
D
T2 Shifting Time
50
100
250
500
5 ~ 50 sec
10
10 ~ 100 sec
Timing Charts
The Y contact is switched on as soon as the power application, and is switched off
at T1 (time setting). After T2 (shift time), the △ contact is switched on. If the power
is switched off with the contact on, the contact is switched off.
Power (2-7)
Y
Y
Indicator
Indicator
☞
☞
Current
1. The power supply voltage must be applied at once using the contacts including switches and relays.
Slow power application may cause timer operation errors.
2. Prolonged continuous conduction shortens the timer life due to the heating of electronic parts in the timer.
3. Pay attention to the polarity when the DC power is supplied to the timer.
Time
Time
4. Cutting off the power as in figure 1 generates bypass leakage
current path through the resistor and condenser and leads to
the timer operation errors. Connect the resistor and condenser
as in figure 2 to prevent the time operation error.
5. Changing the time setting (T1), time range or shift time (T2) during the timer operation may cause an
operation error. Be sure to cut off the power before changing the settings.
6. Do not use the device in the places where:
•the rated temperature or humidity are exceeded;
•the condensation occurs due to the temperature change;
•the flammable or corrosive gas is generated;
•dusts and oil are plentiful or vibration and shock are severe;
•strong alkali or acid substances are used;
•direct sunlight exists; and
•there are devices that generate strong magnetic force or electric noise nearby.
Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr
Industrial Controls Catalog
Ⅲ - 51
Data Processing
0.5
1.0
2. T2(Shifting Time) Specification (msec)
Analog Timer
TTL Series
Part Number Description
TTL
-
❶
❷
❸
❶ Pin Type
8 : 8Pins Socket and Mounted
❷ Function
F : Power Off Delay
❸ Time Unit
S : Second (10s)
General Specification
Model Name
TTL-8FS
Funtion
Power OFF Delay
Timing Range
10sec
Rated Supply Voltage
85V-265VAC 50/60Hz
Power Consumption
0.5VA(120VAC 60Hz), 0.9VA(240VAC 60Hz)
0.5W(110VDC), 0.2W(48VDC), 0.1W(24VDC)
Control
Output
life cycle
Contact Form
2N/O + 2N/C
Contact Capacity
250VAC 3A Resistance Load
Mechanical
Min. 10,000,000
Electrical
Max. 100,000 (250VAC 3A Resistance Load)
Accuracy of Operating Time
Max. ±0.3%
Setting Error
±5%
Influence of Voltage
Max. ±0.5% FS
Influence of Temperature
Max. ±2% FS
Insulation Resistance
100MΩ (for 500VDC)
Dielectric Resistance
2000VAC 50/60Hz for 1 minute
Noise Immunity
the wave form noise (pulse 1us) 2kV by the noise simulator
Vibration
Resistance
Malfunctional
10-55Hz(1 Minute Duration) Dual Wave Length 0.5mm 10 Minutes for Each Direction of X, Y, Z
Destruction
10-55Hz(1 Minute Duration) Dual Wave Length 0.75mm 1 Hour for Each Direction of X, Y, Z
Shock
Resistance
Malfunctional
100m/s2 (10G) Three Times for Each Direction of X, Y, Z
Destruction
300m/s2 (30G) Three Times for Each Direction of X, Y, Z
Ambient Temperature
-10 ~ +55°C (with no icing)
Storage Temperature
-25 ~ +65°C (with no icing)
Ambient Humidity
35 ~ 85%RH
Weight
Approx. 100g (except for the packaging material)
Product Selection
Operating
Mechanism
Time
- 8pins plug type
- Power off delay
Ⅲ - 52
Industrial Controls Catalog
Part Number
sec
www.kacon.co.kr
TTL-8FS
Rev. 2/14
Data subject may change without notice.
Data Processing
Diagram
Timer Function
Contact:
Power Indicator
Output Indicator
Resistive Load
Scale Range
Display Window
Time Setting Knob
Time Range
Selector
☞
Dimension
(mm)
Time Out Display Window
Timing Charts
[Panel processing dimension diagram]
Data Processing
Panel
Socket : K2BF08
The a contact is switched on as soon as the power is supplied. After
the set time (T) from the power off, the a contact is switched off.
Caution
● Power supply
The timer does not operate with the power supplied, but operate after the power is switched off.
☞
● Noise
1) For the test of impulse voltage between the power terminals, a voltage of 2kV with a pulse width of 1μs is applied. For the test of external noise voltage, a voltage of 1kV with a pulse width of 1μs is applied using a noise simulator. For the impulse noise voltage above these values, connect an AC MP condenser or oil condenser (0.1 ~ 1μF) between the power supply terminals.
2) When testing the withstand voltage, impulse voltage and insulation resistance with the device assembled with the control panel,
•Separate this product from the circuit completely.
•Short all terminals (to prevent damage to the internal circuit when some units on the control panel have poor withstand voltage and insulation.)
● Environment
Do not use the device in the places where:
•the rated temperature or humidity are exceeded;
•the condensation occurs due to the temperature change;
•the flammable or corrosive gas is generated;
•dusts and oil are plentiful or vibration and shock are severe;
•strong alkali or acid substances are used;
•direct sunlight exists; and
•there are devices that generate strong magnetic force or electric noise nearby.
Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr
Industrial Controls Catalog
Ⅲ - 53
Analog Timer
TTL Series
Part Number Description
TTL-T
-
❶
❷
❸
❶ Contact
❷ Time Unit
❸ Supply Voltage
1 : temp. DPDT (2N/O + 2N/C)
2 : temp. SPDT (2N/O + 2N/C), order SPST (2N/O + 2N/C)
S : Seconds (1, 3, 6, 10, 30, 60)
M : Minutes (3, 6, 10, 30, 60)
H :Hours (3, 6, 12, 24)
110VAC
220VAC
24VDC
General Specification
Model
Function
Timing Range
Rated Supply Voltage
Operating Voltage Range
Power Consumption
Recovery Time
Contact Form
Control
Output
Contact Capacity
Mechanical
life cycle
Electrical
Accuracy of operating time
Setting Error
Influence of Voltage
Influence of Temperature
Insulation Resistance
Dielectric Resistance
Noise Immunity
Malfunctional
Vibration
Resistance
Destruction
Malfunctional
Shock
Resistance
Destruction
Ambient Temperature
Storage Temperature
Ambient Humidity
Weight
TTL- T1
TTL- T2
Power ON delay
sec(1, 3, 6, 10, 30, 60), min(3, 6, 10, 30, 60), hour(3, 6, 12, 24)
110VAC, 220VAC 50/60Hz, 24VDC
90 ~ 110% of the Supply Voltage
Approx. 10VA(240VAC 60Hz), Approx. 2W(24VDC, 12VDC) DC(Option)
Max. 200ms
Power ON delay(2N/O + 2N/C) Power ON delay(1N/O + 1N/C) / Instantaneous(1N/O + 1N/C)
250VAC 3A resistance load
Min. 10,000,000
Max. 100,000 (250VAC 3A resistance load)
Max. ±0.3%
±5%
Max. ±0.5% FS
Max. ±2% FS
100MΩ (for 500VDC)
2000VAC 50/60Hz for 1 minute
The wave form noise (pulse 1us) ±2kV by the noise simulator
10-55Hz (1 minute duration) Dual Wave Length 0.5mm 10 minutes for Each Direction of X, Y, Z
10-55Hz (1 minute duration) Dual Wave Length 0.75mm 1 h our for Each Direction of X, Y, Z
100m/s2 (10G) Three Times for Each Direction of X, Y, Z
300m/s2 (30G) Three Times for Each Direction of X, Y, Z
-10 ~ +55°C (with no icing)
-25 ~ +65°C (with no icing)
35 ~ 80%RH
Approx. 75g (except for the packaging material)
Product Selection
Contact
form
Power ON
delay DPDT
(2N/O + 2N/
C)
Time
Unit
sec
min
hour
Ⅲ - 54
Time
Range
220VAC
Part Number
110VAC
Contact
Form
24VDC
1
TTL-T1-1S 220VAC TTL-T1-1S 110VAC TTL-T1-1S 24VDC
3
6
Time
Unit
Time
Range
220VAC
Part Number
110VAC
24VDC
1
TTL-T2-1S 220VAC TTL-T2-1S 110VAC TTL-T2-1S 24VDC
TTL-T1-3S 220VAC TTL-T1-3S 110VAC TTL-T1-3S 24VDC delay SPDT
3
TTL-T2-3S 220VAC TTL-T2-3S 110VAC TTL-T2-3S 24VDC
TTL-T1-6S 220VAC TTL-T1-6S 110VAC TTL-T1-6S 24VDC Instantaneous
6
TTL-T2-6S 220VAC TTL-T2-6S 110VAC TTL-T2-6S 24VDC
10
TTL-T2-10S 220VAC TTL-T2-10S 110VAC TTL-T2-10S 24VDC
30
TTL-T2-30S 220VAC TTL-T2-30S 110VAC TTL-T2-30S 24VDC
Power ON
(1N/O + 1N/C),
sec
10
TTL-T1-10S 220VAC TTL-T1-10S 110VAC TTL-T1-10S 24VDC SPST
30
TTL-T1-30S 220VAC TTL-T1-30S 110VAC TTL-T1-30S 24VDC
60
TTL-T1-60S 220VAC TTL-T1-60S 110VAC TTL-T1-60S 24VDC
60
TTL-T2-60S 220VAC TTL-T2-60S 110VAC TTL-T2-60S 24VDC
3
TTL-T1-3M 220VAC TTL-T1-3M 110VAC TTL-T1-3M 24VDC
3
TTL-T2-3M 220VAC TTL-T2-3M 110VAC TTL-T2-3M 24VDC
6
TTL-T1-6M 220VAC TTL-T1-6M 110VAC TTL-T1-6M 24VDC
6
TTL-T2-6M 220VAC TTL-T2-6M 110VAC TTL-T2-6M 24VDC
10
TTL-T1-10M 220VAC TTL-T1-10M 110VAC TTL-T1-10M 24VDC
10
TTL-T2-10M 220VAC TTL-T2-10M 110VAC TTL-T2-10M 24VDC
30
TTL-T1-30M 220VAC TTL-T1-30M 110VAC TTL-T1-30M 24VDC
30
TTL-T2-30M 220VAC TTL-T2-30M 110VAC TTL-T2-30M 24VDC
60
TTL-T1-60M 220VAC TTL-T1-60M 110VAC TTL-T1-60M 24VDC
60
TTL-T2-60M 220VAC TTL-T2-60M 110VAC TTL-T2-60M 24VDC
3
TTL-T1-3H 220VAC TTL-T1-3H 110VAC TTL-T1-3H 24VDC
3
TTL-T2-3H 220VAC TTL-T2-3H 110VAC TTL-T2-3H 24VDC
6
TTL-T1-6H 220VAC TTL-T1-6H 110VAC TTL-T1-6H 24VDC
6
TTL-T2-6H 220VAC TTL-T2-6H 110VAC TTL-T2-6H 24VDC
12
TTL-T1-12H 220VAC TTL-T1-12H 110VAC TTL-T1-12H 24VDC
12
TTL-T2-12H 220VAC TTL-T2-12H 110VAC TTL-T2-12H 24VDC
24
TTL-T1-24H 220VAC TTL-T1-24H 110VAC TTL-T1-24H 24VDC
24
TTL-T2-24H 220VAC TTL-T2-24H 110VAC TTL-T2-24H 24VDC
Industrial Controls Catalog
(1N/O + 1N/C)
www.kacon.co.kr
min
hour
Rev. 2/14
Data subject may change without notice.
Data Processing
Dimension
[Panel processing dimension diagram]
Panel
socket : K2BF08
Diagram
Data Processing
TTL-T1
TTL-T2
Contact :
NO : 250VAC 3A
Resistive Load
(ON delay. 1C)
Contact :
NO : 250VAC 3A
Resistive Load
(Instantaneous. 1C)
(ON delay. 1C)
(ON delay. 1C)
Source
Source
Time Range
Timer Function
Power on Indicator Output Indicator
Scale Range
Display Window
Display unit
Set Time
Timing Range
Set Time
Timing Range
Set Time
Timing Range
1 sec
0 ~ 1 sec
3 min
0 ~ 3 min
3 hour
0 ~ 3 hour
3 sec
0 ~ 3 sec
6 min
0 ~ 6 min
6 hour
0 ~ 6 hour
6 sec
0 ~ 6 sec
10 min
0 ~ 10 min
12 hour
0 ~ 12 hour
10 sec
0 ~ 10 sec
30 min
0 ~ 30 min
24 hour
0 ~ 24 hour
30 sec
0 ~ 30 sec
60 min
0 ~ 60 min
60 sec
0 ~ 60 sec
Timing Charts
Mode
Time Table
Mode
Power 2-7
T1
ON delay NC 1-4 (8-5)
ON delay NO 1-3 (8-6)
T2
Up LED
t : Set Time
Rev. 2/14
Time Table
Power 2-7
Instantaneous NC 1-4
Instantaneous NO 1-3
ON delay NC 8-5
ON delay NO 8-6
Up LED
Rt : Reset time (Minimum 50ms)
Data subject may change without notice.
www.kacon.co.kr
Industrial Controls Catalog
Ⅲ - 55
Analog Timer
TTL Series
Caution
● Environment
● Noise
Do not use the device in the places where:
1) For the test of impulse voltage between the power terminals, a voltage •the rated temperature or humidity are exceeded;
of 2kV with a pulse width of 1 μs is applied. For the test of external noise
•the condensation occurs due to the temperature change;
voltage, a voltage of 1kV with a pulse width of 1 μs is applied using a noise
•the flammable or corrosive gas is generated;
simulator. For the impulse noise voltage above these values, connect an
•dusts and oil are plentiful or vibration and shock are severe;
AC mp condenser or oil condenser (0.1 ~ 1 μF) between the power supply
•strong alkali or acid substances are used;
terminals.
•direct sunlight exists; and
2) When testing the withstand voltage, impulse voltage and insulation
•there are devices that generate strong magnetic force or electric noise nearby.
resistance with the device assembled with the control panel,
•Separate this product from the circuit completely.
•Short all terminals
(to prevent damage to the internal circuit when some units on
the control panel have poor withstand voltage and insulation.)
Accessories (TTL, TTS, TTL Series)
Ⅲ - 56
TTL-PR
(ivory color)
TTL-PK
(black)
TTL-BK
TTS-BK
Socket <K2BF08(8pin), K2BF11(11pin)>
K2BF-F1
(Socket fixture hook)
Industrial Controls Catalog
www.kacon.co.kr
Rev. 2/14
Data subject may change without notice.
Analog Timer
TTM Series
Part Number Description
TTM
- 4 ❶
❷
❸
❶ Time Range
0.5 : 0.5
001 : 1
180 : 180(Seconds Only)
005 : 5
010 : 10
030 : 30
060 : 60
❷ Time Unit
S : Seconds
M : Minute
❸ Supply Voltage
110VAC
220VAC
12VDC
24VDC
110VDC
General Specification
Accuracy of Operating Time
Max. ±1%
Reset Time
Max. 50ms
Contact Form
4N/O + 4N/C, 3A 240VAC (resistance load)
AC : 2VA
Dielectric Strength
Life Cycle
Data Processing
DC : 1.2W
Power Consumption
1,500VAC for 1 minute
Mechanical
Min. 1,000,000
Electrical
Min. 200,000
Rated Voltage
220VAC 50/60 Hz, 110VAC 50/60 Hz, 24VDC. 12VDC
Ambient Temperature
-25°C ~ +70°C (with no icing)
☞ The specification and material of the product can be changed without notice for higher quality.
Product Selection
Contact
Form
4N/O + 4N/C
4N/O + 4N/C
Time
Unit
SEC
MIN
Part Number
Time
Range
220VAC
110VAC
24VDC
12VDC
0.5
TTM-40.5S 220VAC
TTM-40.5S 110VAC
TTM-40.5S 24VDC
TTM-40.5S 12VDC
1
TTM-4001S 220VAC
TTM-4001S 110VAC
TTM-4001S 24VDC
TTM-4001S 12VDC
5
TTM-4005S 220VAC
TTM-4005S 110VAC
TTM-4005S 24VDC
TTM-4005S 12VDC
10
TTM-4010S 220VAC
TTM-4010S 110VAC
TTM-4010S 24VDC
TTM-4010S 12VDC
30
TTM-4030S 220VAC
TTM-4030S 110VAC
TTM-4030S 24VDC
TTM-4030S 12VDC
TTM-4060S 12VDC
60
TTM-4060S 220VAC
TTM-4060S 110VAC
TTM-4060S 24VDC
180
TTM-4180S 220VAC
TTM-4180S 110VAC
TTM-4180S 24VDC
TTM-4180S 12VDC
5
TTM-4005M 220VAC
TTM-4005M 110VAC
TTM-4005M 24VDC
TTM-4005M 12VDC
10
TTM-4010M 220VAC
TTM-4010M 110VAC
TTM-4010M 24VDC
TTM-4010M 12VDC
30
TTM-4030M 220VAC
TTM-4030M 110VAC
TTM-4030M 24VDC
TTM-4030M 12VDC
60
TTM-4060M 220VAC
TTM-4060M 110VAC
TTM-4060M 24VDC
TTM-4060M 12VDC
Dimension
(mm)
Socket
KMY4
KMY4S
Time Chart
Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr
Industrial Controls Catalog
Ⅲ - 57
Analog Timer
TTS Series
Part Number Description
TTS
- B ❶
❷
0.5S (0.5S/5S/30S/3M)
❶ Time Range
060S (60S/10M/60M/6H)
☞ S : Seconds
❷ Supply Voltage
M : Minutes
001S (1S/10S/60S/6M)
005S (5S/50S/5M/30M)
002M (2M/20M/2H/12H)
004M (4M/40M/4H/24H)
010S (10S/100S/10M/60M)
H : Hours
220VAC
110VAC
24VDC
110VDC
General Specification
Accuracy of Operating Time
Max. ±0.5
Reset Time
Max. 100ms
Contact Form
2N/O + 2N/C, 5A 240VAC (Resistance Load)
DC : 1.2W
Power Consumption
AC : 2VA
Dielectric Strength
Life Cycle
1,500VAC for 1 minute
Mechanical
Min. 1,000,000
Electrical
Min. 200,000
Rated Voltage
220VAC, 110VAC, 24VDC, 110VDC (±10% of the regular voltage)
Ambient Temperature
-25°C ~ +70°C
☞ The specification and material of the product can be changed without notice for higher quality.
Ⅲ - 58
Industrial Controls Catalog
www.kacon.co.kr
Rev. 2/14
Data subject may change without notice.
Data Processing
Product Selection
Contact Form
2N/O + 2N/C
2N/O + 2N/C
Dimension
S
M
H
Part Number
Time
Range
220VAC
110VAC
110VDC
24VDC
0.5
TTS-B0.5S 220VAC
TTS-B0.5S 110VAC
TTS-B0.5S 110VDC
TTS-B0.5S 24VDC
1
TTS-B001S 220VAC
TTS-B001S 110VAC
TTS-B001S 110VDC
TTS-B001S 24VDC
5
TTS-B005S 220VAC
TTS-B005S 110VAC
TTS-B005S 110VDC
TTS-B005S 24VDC
10
TTS-B010S 220VAC
TTS-B010S 110VAC
TTS-B010S 110VDC
TTS-B010S 24VDC
30
TTS-B030S 220VAC
TTS-B030S 110VAC
TTS-B030S 110VDC
TTS-B030S 24VDC
50
TTS-B050S 220VAC
TTS-B050S 110VAC
TTS-B050S 110VDC
TTS-B050S 24VDC
60
TTS-B060S 220VAC
TTS-B060S 110VAC
TTS-B060S 110VDC
TTS-B060S 24VDC
100
TTS-B0100S 220VAC
TTS-B0100S 110VAC
TTS-B0100S 110VDC
TTS-B0100S 24VDC
2
TTS-B002M 220VAC
TTS-B002M 110VAC
TTS-B002M 110VDC
TTS-B002M 24VDC
3
TTS-B003M 220VAC
TTS-B003M 110VAC
TTS-B003M 110VDC
TTS-B003M 24VDC
4
TTS-B004M 220VAC
TTS-B004M 110VAC
TTS-B004M 110VDC
TTS-B004M 24VDC
5
TTS-B005M 220VAC
TTS-B005M 110VAC
TTS-B005M 110VDC
TTS-B005M 24VDC
6
TTS-B006M 220VAC
TTS-B006M 110VAC
TTS-B006M 110VDC
TTS-B006M 24VDC
10
TTS-B010M 220VAC
TTS-B010M 110VAC
TTS-B010M 110VDC
TTS-B010M 24VDC
20
TTS-B020M 220VAC
TTS-B020M 110VAC
TTS-B020M 110VDC
TTS-B020M 24VDC
30
TTS-B030M 220VAC
TTS-B030M 110VAC
TTS-B030M 110VDC
TTS-B030M 24VDC
40
TTS-B040M 220VAC
TTS-B040M 110VAC
TTS-B040M 110VDC
TTS-B040M 24VDC
50
TTS-B050M 220VAC
TTS-B050M 110VAC
TTS-B050M 110VDC
TTS-B050M 24VDC
60
TTS-B060M 220VAC
TTS-B060M 110VAC
TTS-B060M 110VDC
TTS-B060M 24VDC
2
TTS-B002H 220VAC
TTS-B002H 110VAC
TTS-B002H 110VDC
TTS-B002H 24VDC
4
TTS-B004H 220VAC
TTS-B004H 110VAC
TTS-B004H 110VDC
TTS-B004H 24VDC
6
TTS-B006H 220VAC
TTS-B006H 110VAC
TTS-B006H 110VDC
TTS-B006H 24VDC
12
TTS-B012H 220VAC
TTS-B012H 110VAC
TTS-B012H 110VDC
TTS-B012H 24VDC
24
TTS-B024H 220VAC
TTS-B024H 110VAC
TTS-B024H 110VDC
TTS-B024H 24VDC
(mm)
Socket
KF083A
Rev. 2/14
Data subject may change without notice.
www.kacon.co.kr
KPZ2
Industrial Controls Catalog
Ⅲ - 59
Data Processing
2N/O + 2N/C
Time Unit
Download