Installation Guide Smart-UPS™On-Line
Replacement Battery Module APCRBC140
Safety Messages
Read the instructions carefully to become familiar with the equipment before trying to install, operate, service or
maintain it. The following special messages may appear throughout this manual or on the equipment to warn of
potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists
which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury.
CAUTION
CAUTION addresses practices not related to physical injury including certain environmental hazards, potential damage or loss
of data.
Safety and General Information
Inspect the package contents upon receipt.
Notify the carrier and dealer if there is any damage.
• Adhere to all local and national electrical codes.
• Always recycle used batteries.
For information on recycling used battery modules, refer to the Battery Disposal Information sheet included
with the replacement battery module.
• Recycle the package materials or save them for reuse.
Battery safety
• Before installing or replacing the batteries, remove jewelry such as wristwatches and rings.
High short circuit current through conductive materials could cause severe burns.
• Do not dispose of batteries by burning them. The batteries may explode.
• Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.
Replace Battery Modules
CAUTION
DAMAGE TO EQUIPMENT OR PERSONNEL
• The equipment is heavy. Each battery module weighs 17 kg (37 lb).
• Always practice safe lifting techniques adequate for the weight of the equipment.
• Adhere to all local and national electrical codes.
• Use the battery model handle to slide the battery modules in and out of the UPS and external battery pack (XLBP).
• Do not use the handle to lift or carry the battery module.
Failure to follow these instructions can result in equipment damage and minor or moderate injury.
Note: The batteries will charge to 90% capacity in the first three hours of operation on utility power.
Do not expect full runtime capability during this initial charge period.
SRT5K/SRT6K UPS models
1
2
2b
su09 2
su0
923
a
3
4
su08
1a
su084
5
42 a
6
s u08
4 3a
s u08
2
Smart-UPS On-Line APCRBC140
44a
7
8
s u084
su0
9 23
4b
b
9
:
su08
su 0843
42 b
b
;
<
41b
su08
Smart-UPS On-Line APCRBC140
su 092
2a
3
SRT8K/SRT10K UPS models
1
2
su0
suo0779c
x2 boxes
x4 battery modules
923
a
4
x4
5
suo0776b
suo0778b
3
6
su0
9 23
suo0776a
x2 boxes
x4 battery modules
b
x4
4
Smart-UPS On-Line APCRBC140
suo0779d
8
suo0778a
7
External battery pack APCRBC140
1
2
x2 boxes
x4 battery modules
9a
su0 92
su0
923
a
3
4
x4
16 a
su09
a
su0889
5
6
x2 boxes
x4 battery modules
0a
su0 89
su0
9 23
7
b
8
90b
su08
89b
su08
9
:
x4
16 b
su09
9b
su0 92
Smart-UPS On-Line APCRBC140
5
Reset Battery Installation Date
1 POWER ON/OFF button
2 Load icon
Disable/mute audible alarm icon
3 UPS status information
LOAD
4 Operation mode icons
5 ESCAPE button
Output 230.0 v
6 OK button
7 UP/DOWN arrow buttons
On-Line
1
2
3
8 Controllable outlet group status
icons
9 Battery status icons
su0870a
The battery installation date will appear on the display interface within two minutes of battery installation. If the
installation date does not appear on the display interface, use the UP/DOWN arrow buttons to navigate to the Config
Menu > Battery and enter the correct Installation Date.
When the replacement battery cartridge (RBC), is charged to full capacity, perform a Self Test and a Runtime
Calibration Test.
Customer support and warranty information are available on the
APC by Schneider Electric web site, www.apc.com.
© 2014 APC by Schneider Electric. APC, the APC logo, Smart-UPS and PowerChute are owned
by Schneider Electric Industries S.A.S. or their affiliated companies. All other trademarks are
property of their respective owners.
EN 990-5181
1/2014