625030900G_AM-513_ig_VVTK_rev1.0_20150610.indd 1
VIVOTEK Fixed Dome & PTZ Series
Mounting Cap
Installation Guide
Using AM-513 mounting cap
and compatible accessories
Rev. 1.0
Ordering part no.:
100138100G ASS'Y KIT,AM-513_V01
Part no.: 625030900G
IP Sur veillance
2015/6/16 上午 09:03:49
Revision History:
* Rev. 1.0: Initial Release
AM-513 Mounting Cap Mechanical Drawings
I
Compatible VIVOTEK Cameras
Fixed Dome series
FD8367-V / FD8338-HV / FD8367-TV
You may also refer to VIVOTEK's website for the list of supported models. Support for other models can
be available through time.
625030900G_AM-513_ig_VVTK_rev1.0_20150610.indd 2
2
2015/6/16 上午 09:03:49
English
II
Installation
Mounting Hole Definitions
Above are the locations of different groups of mounting holes for matching different junction
boxes:
Hole
Type
Applicable Box
Drawings
Screw
No. of
screws
4" square box
1
#8-32, L15
(User-supplied)
2
#8-32, L15
(User-supplied)
2
#6-32, L15
(User-supplied)
2
4" octagon box
2
1" single gang box
3
625030900G_AM-513_ig_VVTK_rev1.0_20150610.indd 3
3
2015/6/16 上午 09:03:49
NOTE:
1. Route cables before you secure the accessories to a wall.
2. For details on the cable connections with each camera, please refer to their Quick
Installation Guide.
Installing the Mounting Cap
1. Install the panhead screws to the mounting cap. Do not completely tighten the screws
yet. Leave about 5mm of clearance between the screw heads and the top of mounting
holes.
625030900G_AM-513_ig_VVTK_rev1.0_20150610.indd 4
5mm
4
2015/6/16 上午 09:03:50
English
2. Route cables through the junction box.
3. Orient and secure the mounting cap to the junction box.
625030900G_AM-513_ig_VVTK_rev1.0_20150610.indd 5
5
2015/6/16 上午 09:03:50
4. Open the top cover, and remove the waterproof cable glands from the camera.
5. Pull the Ethernet cable through the cabling hole. If you have other IO wires, also pull
them through the cabling hole.
625030900G_AM-513_ig_VVTK_rev1.0_20150610.indd 6
6
2015/6/16 上午 09:03:52
English
6. Orient and secure the camera to the mounting cap.
Turn the camera counter-clockwise, and then secure the
mounting screws.
7. Pass the cable through the rubber seal, clamping claw, and the seal nut. Use a crimping
tool to make an RJ45 connector for the cable. When done, connect the Ethernet cable
to the camera.
6
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
o
O
g
B
b
G
br
BR
625030900G_AM-513_ig_VVTK_rev1.0_20150610.indd 7
1
2
3
4
5
6
7
8
7
2015/6/16 上午 09:03:55
8. Install the dome cover.
Follow the documentation that came with the camera for the rest of the configuration
details.
625030900G_AM-513_ig_VVTK_rev1.0_20150610.indd 8
8
2015/6/16 上午 09:03:56