Programmable Logic Controller
PLC
HMI
SENSOR
ENCODER
COUNTER
INFORMATION
Process Control
Features/Specifications
Signal Conditioners
Signal integrity starts with quality measurement and good
equipment. However, even with the best equipment, signals
can be degraded if the equipment is not properly installed
or it is not protected by signal conditioners/signal isolators.
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
■Features
DL05/06
FC-33
DL205
D4
D3
Programmer
DirectSOFT
Terminator I/O
Process Control
ZIP LINK
Features
Specifications
Dimensions
FC Series Signal
Conditioners
Field configurable input and output, unipolar input ranges of 0-5 V, 0-10 V,
0-20 mA or 4-20 mA, and bipolar output ranges of ±100 mV, ±50 mV,
±5 V, ±10 V, ±15 V. Field calibrated with offset and span adjustments.
Field configurable input and output ranges of 0-5 V, 0-10 V, 0-20 mA and
4-20 mA with 1,500 V DC isolation between input and output, and 1,500
V DC isolation from 24 volt power and input/output. LED indicates normal
operation and is used in conjunction with the calibration pushbutton for the
internal calibration process.
- 3-way 1,500 V isolation
- Push button calibration
FC-B34
Field configurable input and output, bipolar input ranges of ±100 mV,
±50 mV, ±5 V, ±10 V, ±15 V, and unipolar output ranges of 0-5 V, 0-10
V, 0-20 mA or 4-20 mA. Field calibrated with offset and span adjustments.
FC-11
FC-ISO-C
Loop powered 4-20 mA input/output signal with 1,500 V DC isolation
between input and output.
- 1,500 V isolation
- Loop powered
Ideal for use with single-ended (open collector, NPN, pull-up, push-pull,
totem pole) or differential line driver encoders. Three complementary inputs
(A, B, Z, A-not, B-not, Z-not) are rated for 4.5-7.5 and 12-26 V DC and
frequency response up to 1 MHz.
Optical isolation separates the input signals from three complementary open
collector outputs (A, B, Z, A-not, B-not, Z-not) rated for 5-36 V DC that can
be used in single-ended configurations.
FC-T1
Field configurable input for type J, K, E, T, R, S, B, N and C thermocouples
or ±156.25 mV inputs with 1,500 V DC isolation between input and the
4-20 mA output. Cold junction compensation and burnout detection. Alarm/
run LED.
- 1,500 V isolation
- Cold junction compensation (CJC)
- Internal diagnostics (burnout detection or calibration errors)
FC-ISO-D
Ideal for use with single-ended (open collector, NPN, pull-up, push-pull,
totem pole) or differential line driver encoders. Three complementary inputs
(A, B, Z, A-not, B-not, Z-not) are rated for 4.5-7.5 and 12-26 V DC and
frequency response up to 1 MHz.
Optical isolation separates the input signals from three differential line driver
outputs (A, B, Z, A-not, B-not, Z-not) rated for 5 V DC.
FC-R1
Loop powered, non-isolated, 3-wire unit converts an RTD input to a linear
4-20 mA signal. User selectable CU10, PT100 or PT1000 input.
FC-P3
Field configurable input and output, input ranges of 3-wire potentiometer
0 to 100 ohms through 0 to 100 kilohms, and output ranges of 0-5 V, 0-10 V,
0-20 mA or 4-20 mA. Field calibrated to 10% of potentiometer full range.
■Model Number List
Model Number
FC-33
FC-11
FC-T1
FC-R1
FC-P3
FC-35B
FC-B34
FC-ISO-C
FC-ISO-D
300
FC-35B
Outline
Description
DC selectable signal conditioner with 3-way isolation
4-20 mA isolated signal conditioner
Thermocouple/mV isolated signal conditioner
RTD input signal conditioner
Potentiometer input, analog output signal conditioner
Unipolar voltage or current to bipolar voltage signal conditioner
Bipolar voltage to unipolar voltage or current signal conditioner
Encoder signal conditioner and optical Isolator - open collector output
Encoder signal conditioner and optical Isolator - differential line driver output
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
Latest catalog (free) is available online.
Weight (g)
171.0
146.5
160.0
152.5
136.0
136.0
136.0
136.0
136.0
Visit our website ▼
Price
Open
Open
Open
Open
Open
Open
Open
Open
Open
http://www.koyoele.co.jp/english/
Programmable Logic Controller
Process Control
Dimensions
■Dimensions (Unit: mm)
2X R3.0 2X R3.0
11.5
11.5
122.8
122.8
2X R3.0 2X R3.0
11.5 2X R3.0 2X R3.0
11.5
122.8
122.8
122.8
122.8
122.8
122.8
2X R3.0 2X R3.0
FC-33
11.5
11.5
11.5
11.5
FC-33
FC-33
FC-33
FC-33
115.1
115.1 103.1
89.0
103.1
115.1
115.1
115.1
115.1 103.1
115.1 103.1
115.1 103.1
6.0
103.1 89.0
89.0
103.1 89.0
89.0
103.1 89.0
89.0
6.0
FC-33
FC-33
FC-33
FC-33
23.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
6.0
6.0
6.0
2X R3.0 2X R3.0
11.5
FC-11
11.5
11.5
11.5
11.5
2X R3.0 2X R3.0
11.5
2X R3.0 2X R3.0
11.5 2X R3.0 2X R3.0
11.5
FC-11
FC-11
FC-11
FC-11
115.1
115.1 103.1
115.1
115.1
115.1
103.1 89.0
115.1 103.1 89.0
103.1 89.0
115.1 103.1 89.0
103.1 89.0
115.1 103.1 89.0
6.0
6.0
FC-11
FC-11
23.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
FC-T1
11.5
11.5
11.5
11.5
11.5
FC-11
FC-11
6.0
6.0
6.0
89.0
103.1
2X R3.0 2X R3.0
2X R3.0 2X R3.0
11.5
2X R3.0 2X R3.0
11.5 2X R3.0 2X R3.0
11.5
FC-T1
FC-T1
FC-T1
FC-T1
8.7
8.7
8.7
34.9 77.9
34.9 77.9
57.5
34.957.5
34.9 77.9
77.9
34.9
77.9
57.5
57.5 34.9 77.9
57.5
110.2 110.2 57.5
57.5
57.5
129.1 129.1
110.2 110.2
129.1
110.2 129.1
110.2
110.2 129.1
110.2
129.1
129.1 129.1
FC-33 FC-33
122.8
122.8
122.8
122.8
122.8
122.8
122.8
2X ∅6.22X ∅6.2
122.8
122.8
122.8
122.8
122.8
122.8
FC-P3
FC-P3
FC-P3
89.0
103.1
89.0
115.1
115.1
115.1
115.1 103.1 103.1
89.0
115.1 103.1 103.1
89.0
115.1 103.1 103.1
89.0
6.0
6.0
89.0
89.0
89.0
FC-P3
FC-P3
FC-P3
FC-P3
23.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
2X ∅6.22X ∅6.2
FC-11
6.0
6.0
6.0
2X R3.0 2X R3.0
2X R3.0 2X R3.0
2X R3.0 2X R3.0
FC-35B
FC-35B
115.1
115.1 103.1
89.0
103.1
89.0
115.1
115.1
115.1
115.1 103.1 103.1
89.0
115.1 103.1 103.1
89.0
115.1 103.1 103.1
89.0
6.0
6.0
89.0
89.0
89.0
FC-35B
FC-35B
FC-35B
FC-35B
23.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
FC-11 FC-11
FC-11 FC-11
FC-11 FC-11
6.0
6.0
6.0
FC-B34
2X R3.0
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
FC-B34
FC-B34
112.3
112.3
112.3
112.3
112.3
112.3
112.3
112.3
2X R3.0
2X R3.0 2X R3.0
2X R3.0 2X R3.0
2X R3.0 2X R3.0
FC-B34
FC-B34
112.3
112.3
112.3
112.3
112.3
112.3
112.3
2X R3.1 2X R3.1
34.9 77.9
34.9 77.9
34.957.5
34.9 77.9
77.9
34.9
77.9
57.5
57.5 34.9 77.9
57.5
110.2 57.5
57.5
118.6 57.5
110.2
118.6
110.2
110.2
118.6
118.6
FC-35B FC-35B
112.3
112.3
112.3
112.3
112.3
112.3
112.3
112.3
2X R3.1 2X R3.1
89.0
34.9 77.9
34.9 77.9
115.1
115.1 103.1
89.0
103.1
89.0
34.9 77.9
34.9 77.9
34.9 77.9
34.9 77.9
57.5
34.957.5
34.9 77.9
77.9
34.9
77.9
57.5
57.5 34.9 77.9
57.5
57.5
110.2 110.2
57.5
57.5
129.1 129.1
110.2 110.2
129.1
110.2 129.1
110.2
110.2 129.1
110.2
129.1
129.1 129.1
115.1
115.1
115.1
115.1 103.1 103.1
89.0
115.1 103.1 103.1
89.0
115.1 103.1 103.1
89.0
6.0
6.0
89.0
89.0
89.0
34.9 77.9
34.9 77.9
57.5
34.957.5
34.9 77.9
77.9
34.9
77.9
57.5
57.5 34.9 77.9
57.5
57.5
110.2
57.5
118.6 57.5
110.2
118.6
110.2
110.2
118.6
118.6
FC-T1
23.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
6.0
6.0
6.0
89.0
103.1
6.0
6.0
6.0
11.5
11.5
11.5
115.1
115.1
115.1
115.1
11.5
2X R3.0 2X R3.0
2X R3.0 2X R3.0
11.5
2X R3.0 2X R3.0
11.5 2X R3.0 2X R3.0
11.5
FC-R1
FC-R1
FC-R1
FC-R1
115.1 103.1
FC-R1
FC-R1
FC-R1
FC-R1
89.0
103.1
23.0
23.0
23.0
23.0
23.0
23.0
23.0
6.0
6.0
6.0
6.0
6.0
6.0
122.8
122.8
122.8
122.8
122.8
122.8
122.8
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
34.9 77.9
34.9 77.9
89.0
103.1 89.0
115.1 103.1 89.0
103.1 89.0
115.1 103.1 89.0
103.1 89.0
115.1 103.1 89.0
6.0
6.0
23.0
122.8
34.9 77.9
34.9 77.9
34.957.5
34.9 77.9
77.9
34.9
77.9
57.5
57.5 34.9 77.9
57.5
110.2 110.2 57.5
57.5
57.5
129.1 129.1
110.2 110.2
129.1
110.2 129.1
110.2
110.2 129.1
110.2
129.1
129.1 129.1
FC-R1 FC-R1
57.5
FC-B34
FC-B34
FC-B34
23.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
FC-T1 FC-T1
FC-T1 FC-T1
FC-T1 FC-T1
FC-R1
11.5
FC-T1 FC-T1
FC-B34
6.0
6.0
6.0
110.2
118.6
110.2
118.6
110.2
110.2
118.6
118.6
6.0
6.0
6.0
FC-ISO-C/FC-ISO-D
2X R3.0 2X R3.0
11.5
11.5
11.5
11.5
11.5
11.5
11.5
11.5
115.1
115.1 103.1
89.0
103.1
89.0
115.1
115.1
115.1
115.1 103.1 103.1
89.0
115.1 103.1 103.1
89.0
115.1 103.1 103.1
89.0
6.0
6.0
89.0
89.0
89.0
FC-ISO-C
FC-ISO-C
2X R3.0 2X R3.0
2X R3.0 2X R3.0
2X R3.0 2X R3.0
FC-ISO-C
FC-ISO-C
FC-ISO-C
FC-ISO-C
FC-ISO-C
FC-ISO-C
23.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
6.0
6.0
6.0
FC-R1 FC-R1
FC-R1 FC-R1
FC-R1 FC-R1
The specifications and prices described in this catalog were valid when the catalog was issued.
For the latest information, contact our sales persons or see our website.
6.0
6.0
6.0
112.2
112.2
112.2
112.2
112.2
112.2
112.2
112.2
FC-35B FC-35B
FC-35B FC-35B
FC-35B FC-35B
2X R3.1 2X R3.1
2X R3.1 2X R3.1
2X R3.1 2X R3.1
103.1 89.0
115.1 103.1 89.0
103.1 89.0
115.1 103.1 89.0
103.1 89.0
115.1 103.1 89.0
6.0
6.0
2X ∅6.22X ∅6.2
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
57.5
115.1 103.1
FC-T1
FC-P3 FC-P3
FC-P3 FC-P3
FC-P3 FC-P3
34.9 77.9
34.9 77.9
115.1
115.1
115.1
FC-T1
COUNTER
2X R3.1 2X R3.1
2X R3.1 2X R3.1
2X R3.1 2X R3.1
115.1
FC-T1
ENCODER
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
35.0 77.9
35.0 77.9
57.5
35.057.5
35.0 77.9
77.9
35.0
77.9
57.5
57.5 35.0 77.9
57.5
110.1 57.5
57.5
118.6 57.5
110.1
118.6
110.1
110.1
118.6
118.6
FC-P3 FC-P3
112.3
110.2
118.6
110.2
118.6
110.2
110.2
118.6
118.6
6.0
6.0
6.0
2X ∅6.22X ∅6.2
35.0 77.9
35.0 77.9
110.1
118.6
110.1
118.6
110.1
110.1
118.6
118.6
6.0
6.0
6.0
2X R3.0 2X R3.0
FC-35B
FC-35B
34.9 77.9
34.9 77.9
34.957.5
34.9 77.9
77.9
34.9
77.9
57.5
57.5 34.9 77.9
57.5
110.2 110.2 57.5
57.5
57.5
129.1 129.1
110.2 110.2
129.1
110.2 129.1
110.2
110.2 129.1
110.2
129.1
129.1 129.1
FC-11
122.8
2X R3.0 2X R3.0
8.7
2X R3.0 2X R3.0
8.7
FC-P3
FC-35B
57.5
2X R3.0 2X R3.0
115.1 103.1
FC-33 FC-33
FC-33 FC-33
FC-33 FC-33
34.9 77.9
34.9 77.9
122.8
8.7
2X R3.0 2X R3.0
FC-P3
8.7
115.1
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
89.0
6.0
6.0
6.0
8.7
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
34.9 77.9
34.9 77.9
122.8
HMI
SENSOR
2X ∅6.22X ∅6.2
89.0
6.0
6.0
6.0
PLC
DL05/06
DL205
D4
D3
Programmer
DirectSOFT
Terminator I/O
Process Control
ZIP LINK
FC-B34 FC-B34
FC-B34 FC-B34
FC-B34 FC-B34
FC-B34 FC-B34
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
2X ∅6.22X ∅6.2
Features
34.9 77.9
34.9 77.9
34.9 77.9
34.9 77.9
34.957.5
34.9 77.9
77.9
34.9
77.9
57.5
57.5 34.9 77.9
57.5
57.5
110.2
57.5
118.5 57.5
110.2
118.5
110.2
110.2
118.5
118.5
FC-ISO-C/FC-ISO-D
FC-ISO-C/FC-ISO-D
57.5
110.2
118.5
110.2
118.5
110.2
110.2
118.5
118.5
Specifications
Dimensions
FC Series Signal
Conditioners
FC-ISO-C/FC-ISO-D
FC-ISO-C/FC-ISO-D
FC-ISO-C/FC-ISO-D
FC-ISO-C/FC-ISO-D
FC-ISO-C/FC-ISO-D
FC-ISO-C/FC-ISO-D
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
301
Programmable Logic Controller
PLC
HMI
SENSOR
ENCODER
Process Control
FC Series Signal Conditioners
■DC Selectable Signal Conditioner
FC-33
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
DL05/06
DL205
D4
D3
Programmer
DirectSOFT
Terminator I/O
General Specifications
Items
Input Ranges
Specifications
0-5 V, 0-10 V, 0-20 mA, 4-20 mA
Input Impedance
250 Ω, ±0.1% current input
200 ΩK/ 400 KVoltage input
Output Ranges
0-5 V, 0-10 V, 0-20 mA, 4-20 mA
Load Impedance
2 ΩK minimum, voltage output
0 Ω minimum, current output
Maximum Load/Current
Sample Duration Time
Filter Characteristic
Linearity Error
Stability
Accuracy vs. Temperature
Input Power
Recommended Fuse
550 Ω @ 24 V DC (sink/source)
10 mS
-3 dB @ 3 Hz, -6 dB/octave
0.05% FSO maximum
0.05% FSO maximum
0.005%/˚C, (50 ppm/˚C)
24 V DC, ±10% @ 50 mA
0.032 mA, Series 217, current inputs
Isolation
1,500 V DC input - output*
1,500 V DC power - input*
1,500 V DC power - output*
*applied for 1 second
Maximum Inaccuracy of
Output
0.05% @ 25˚C, FSO maximum
0.25% @ 0-60˚C, FSO maximum
Output Current
21 mA maximum (for mA output)
Approx. Field Cal. Range
0 - 25% (0 - 1.5 V / 5 V mode)
80% - 102% (4 - 5.1 V / 5 V mode)
Operating Temperature
Storage Temperature
Relative Humidity
Vibration
Shock
Noise Immunity
0-60˚C (32 to 140˚F)
-20 to 70˚C (-4 to 158˚F)
5 to 90% (non-condensing)
ML STD 810C 514.2
ML STD 810C 516.2
NEMA ICS3-304
Process Control
ZIP LINK
Features
Specifications
Dimensions
FC Series Signal
Conditioners
Application
The FC-33, field configurable isolated input/output signal conditioner, is
useful in eliminating ground loops and interfacing sensors to PLC analog
input modules. The FC-33 has 3-way isolation; this feature solves many
types of configuration problems. For example, the signal conditioner can be
configured for a sinking input and a sourcing output. It also allows signal
translation from current input to voltage output or voltage input to current
output.
This feature would be useful in a system design with a limited type and
number of channels – for example: eight channels of 0-10 V DC, seven of
which are used, and one 4-20 mA input transmitter.
Wiring Diagram
Voltage
Transmitter
+
-
0 to 10 V DC
(example)
-
+
Module Supply
24 V DC
Voltage Input and Current Output (example)
Overview
The FC-33 is a DIN-rail or side-mount, selectable input/output signal
conditioner with 1,500 V DC isolation between input and output, and 1,500 V
DC isolation between 24-volt power and input/output. The field configurable
input/output types allow a wide ranging capability for 0-5 V, 0-10 V, 0-20
mA and 4-20 mA signals.
The FC-33 has built-in self-calibration, but also has OFFSET (zero) and SPAN
(full scale) adjustments of the output signal. The OFFSET has an adjustment
range of 0 to 25% of full scale input and the SPAN has an adjustment of 80%
to 102%.
Level LED: The LED is a powerful tool when setting up the signal conditioner.
During normal operation the LED will blink at a proportional rate to the
selected input signal level. When performing field calibration the LED is used
for indication of the internal calibration process.
CAL-Pushbutton: This pushbutton, along with various switch settings, allows
you to calibrate the OFFSET and/or SPAN for your application or to restore
factory default calibration.
302
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
Latest catalog (free) is available online.
Visit our website ▼
http://www.koyoele.co.jp/english/
Programmable Logic Controller
Process Control
FC Series Signal Conditioners
PLC
HMI
SENSOR
■4-20 mA Isolated Signal Conditioner
FC-11
ENCODER
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
General Specifications
Application
Items
Specifications
Input Ranges
Extended Input range*1
4-20 ma
3.5 mA to 20.6 mA, ± 1%
Input Burden Voltage* 2
Maximum Input Current
Output Burden Voltage* 3
6.8 V DC
34 mA @ 9.7 V DC
8.5 V DC minimum
Output Range
Extended Output Range*1
4-20 mA
3.5 mA to 20.6 mA, ± 1%
Maximum Load Impedance
Maximum Output Current
Sample Duration Time
Linearity Error
650 Ω @ 24 V DC, 1,000 Ω 29 V DC
23 mA @ 29 V DC
18 mS maximum
0.1% FSO maximum
Max Inaccuracy of Output
0.05% @ 25˚C, FSO maximum,
0.3% @ 0-60˚C, FSO maximum
Output Current
(Factory Calibration)
Storage Temperature
DL05/06
DL205
D4
Wiring Diagram
Filter Characteristics
-3 dB @ 200 Hz, -6 dB / octave
Stability
0.1% FSO maximum
21 mA
Accuracy vs. Temperature 20 mA± 0.0065% / ˚C (65ppm / ˚C)
Isolation
1,500 V DC Input - Output
Operating Temperature
0 to 60˚C (32 to 140˚F)
Relative Humidity
Vibration
Shock
Noise Immunity
SJ
The FC-11 isolated input/output signal conditioner is useful in eliminating
ground loops and sinking/sourcing issues when interfacing to PLC analog
input modules. The FC-11 design feature solves many types of configuration
problems. For example, the signal conditioner can solve the problem of
connecting a sinking input transmitter to a sinking analog input module.
D3
Programmer
DirectSOFT
4-Wire
4-20 mA
Transmitter
-
Terminator I/O
Process Control
+
Transmitter
Supply
ZIP LINK
-20 to 70˚C (-4 to 158˚F)
5 to 90% (non-condensing)
4 mA
ML STD 810C 514.2
3.6 mA
ML STD 810C 516.2
NEMA ICS3-304
4 mA
20 mA
-
Note: 1. When adjusting SPAN and OFFSETInput
potentiometer
Current
2. Voltage required to power internal circuitry
3. Formula, [(output load) x 20 mA] + 8.5 V,.i.e.: 13.5 V DC @ 250 Ω
4. Internal analog converter resolution is 12-bit
Specifications
4-20 mA Input Isolated to 4-20 mA Output (example)
4-Wire
4-20 mA
Transmitter
Input/Output Operation
-
21 mA
20 mA
Output Current
(Factory Calibration)
Overview
The FC-11 is a DIN-rail or side-mount, 4-20 mA Input/Output loop powered
signal conditioner with 1,500 V DC isolation between input and output.
The FC-11 has a user-selectable factory calibration. The output can also
be calibrated with OFFSET (zero) and SPAN (full scale) adjustments. The
OFFSET has an adjustment range of 0 to 25% of full scale input and the
SPAN has an adjustment of 80% to 102%.
Features
+
Module Supply
24 V DC
Dimensions
FC Series Signal
Conditioners
+
Transmitter
Supply
4 mA
3.6 mA
4 mA
20 mA
Input Current
4-20 mA I
The specifications and prices described in this catalog were valid when the catalog was issued.
For the latest information, contact our sales persons or see our website.
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
303
Programmable Logic Controller
Process Control
PLC
HMI
FC Series Signal Conditioners
SENSOR
■Thermocouple/mV Input Isolated Signal Conditioner
FC-T1
ENCODER
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
General Specifications
SJ
Items
DL05/06
DL205
D4
Input Ranges
D3
Programmer
DirectSOFT
Terminator I/O
Output Range
External Power Supply
Input Impedance
Absolute Maximum Rating
Process Control
ZIP LINK
Features
FC Series Signal
Conditioners
Output Current
Dimensions
Resolution*1
0.23˚C
0.37˚C
0.295˚C
0.42˚C
0.42˚C
0.15˚C
0.315˚C
0.33˚C
0.55˚C
0.038 mV
0.076 mV
Maximum Inaccuracy
±3˚C, Temperature Input
±0.1%, Voltage Input
Linearity Error
Over Temperature Error
Insulation Resistance
Isolation
0.1%
0.1 X 10-5% (10 ppm)/˚C
≧100 Mr with 500 V DC (Input to output power)
1,500 V AC @ 1 Sec. (Input to output commons)
Sample Duration Time
120 mS Voltage Input
250 mS Thermocouple Input
Common Mode Rejection
Input Filter (FIR)
-100 dB @ DC, -90 dB @ 50/60 Hz
-3 dB @ 15 Hz, -100 dB @ 50 Hz, -100 dB @ 60 Hz
Broken Thermocouple
Up/Down Scale
Red/Green LED
20 mA
Specifications
Specifications
T/C ˚C
˚F
J
-190 to 760
-310 to 1,400
K
-150 to 1,372 -238 to 2,502
E
-210 to 1,000 -345 to 1,832
R
65 to 1,768
149 to 3,214
S
65 to 1,768
149 to 3,214
T
-230 to 400
-382 to 752
B
529 to 1,820 984 to 3,308
N
-70 to 1,300 -94 to 2,372
C
65 to 2,320
149 to 4,208
0 to 156.25 mV
-156.25 mV to +156.25 mV
4 to 20 mA
15 mA, 22 to 26 V DC
> 5 ΩM
Fault protected input ±50 V
Over Range
Up Scale
Under Range
Down Scale
Burnout Time
≦3 Seconds
12 mA
Cold
Junction Compensation Automatic
Warm-up Time
30 min. typical ±1˚C repeatability
Operating Temperature
0 to 60˚C (32 to 140˚F)
Storage Temperature
-20 to 70˚C (-4 to 158˚F)
Relative Humidity
5 to 90% (non-condensing)
Environmental
Air
No
corrosive gases permitted
4 mA
285˚C
760˚C
Vibration-19 0˚C
ML STD 810C 514.2
Shock
STD
810C 516.2
Input Temperature - JML
type
Thermocouple
Noise Immunity
NEMA ICS3-304
The temperature calculation and linearization are based on data provided by
the National Institute of Standards and Technology (NIST).
ALARM and RUN LED: This LED is bicolor (red and green). A red LED
indicates either power up, a fault with internal calibration, or a thermocouple
burnout condition, while a green LED indicates normal operation.
Burnout Function: The output current can be selected to provide either
upscale (20 mA) or downscale (4 mA) detection whenever thermocouple
burnout occurs.
Application
The FC-T1, field configurable thermocouple/mV signal conditioner, is useful
in eliminating ground loops and for interfacing to PLC analog input modules.
If your requirements are only for one channel of temperature, you can add the
signal conditioner to your 4-20 mA input module. Or, if your requirements are
for a single millivolt signal source, you have the option of adding this input to
your analog module.
Wiring Diagram
+
Thermocouple
I+
COM
+
-
Module Supply
24 V DC
Input/Output Operation
20 mA
Output Current
Overview
12 mA
4 mA
-19 0˚C
285˚C
760˚C
Input Temperature - J type Thermocouple
304
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
Thermocouple
*1 Internal analog converter resolution is 12-bit.
The FC-T1 is a DIN-rail or side-mount thermocouple/mV input signal
conditioner with 1,500 V AC isolation between input and output.
The field configurable input allows a wide ranging capability for a type J, K, E,
R, S, T, B, N and C thermocouple, or 0-156.25 mV and 156.25 mV signals.
The FC-T1 has built-in self-calibration, but also offers OFFSET (zero) and
SPAN (full scale) potentiometer for adjustment of the output signal.
The FC-T1 is also equipped with cold junction compensation (CJC) circuitry
to provide an internal ice-point reference.
+
Latest catalog (free) is available online.
Visit our website ▼
http://www.koyoele.co.jp/english/
Programmable Logic Controller
Process Control
FC Series Signal Conditioners
PLC
HMI
SENSOR
■RTD Input Loop Powered Signal Conditioner
FC-R1
ENCODER
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
General Specifications
Items
Application
Input Ranges
CU10
PT100
PT1000
RTD Excitation Current
CU10, PT100 500 μA ±50 μA
PT1000 80 μA ±20 μA
Common Mode Range
Output Range
0 - 3.5 V DC
4-20 mA (linearized)
Maximum Inaccuracy
0.35% FSO / CU10
0.2% FSO @ 25˚C / PT100 & PT1000
0.26% FS0 @ 60˚C / PT100 & PT1000
SJ
The FC-R1 field configurable input signal conditioner is useful for interfacing
RTD sensors to PLC analog current input modules. It is recommended that
shielded RTDs be used whenever possible to minimize noise on the input
signal.
Specifications
-200˚C to 260˚C
-328˚F to 500˚F
-200˚C to 850˚C
-328˚F to 1,562˚F
-200˚C to 595˚C
-328˚F to 1,103˚F
Wiring Diagram
D3
Programmer
DirectSOFT
Process Control
1% @ 20 mS Red (if applicable) (+)
applicable)
No 40
Connection
105 dB @ DC,Red
60 (ifdB
@ 10 Hz,
dB @ 60Hz
(if sensor has 4 leads,
0.05% FSO maximum
only connect one lead to +)
0 to 60˚C (32 to
140˚F)
Black
(-)
-20 to 70˚C (-4Black
to 158˚F)
(COM)
5 to 90% (non-condensing)
No corrosive gases permitted
ML STD 810C 514.2
ML STD 810C 516.2
NEMA ICS3-304
ZIP LINK
-
+
Module Supply
24 V DC
RTD Signal Conditioner to 4-20 mA DL05/06 Analog Module
Only Use Three Wire and Four Wire RTDs.
Features
Input/Output Operation
Specifications
20 mA
Overview
The FC-R1 is a DIN-rail or side-mount Resistive Temperature Detector signal
conditioner. It is a non-isolated signal conditioner which converts a 3-wire
RTD to a linearized 4-20 mA current loop signal.
The FC-R1 has a user selectable CU10 (10 Ohm copper), PT100 (100 Ohm
platinum) or PT1000 (1,000 Ohm platinum) RTD input, and also offers
OFFSET (zero) and SPAN (full scale) adjustments of the output signal. The
OFFSET has an adjustment range of 0 to 25% of full scale output and the
SPAN has an adjustment of 80% to 102%. 20 mA
Red (if applicable)
Output Current
4 mA
Output Slew Rate
Filter Characteristics
Stability
Operating Temperature
Storage Temperature
Relative Humidity
325˚C Air
850˚C
-200˚C Environmental
Input Temperature - PT100 type RTD
Vibration
Shock
Noise Immunity
Terminator I/O
0.35% FSO / CU10
0.2% FSO / PT10 & PT1000
Red (if applicable)
12 mA
Black
Black
4 mA
325˚C
-200˚C
Red (if applicable)
12 mA
Black
Black
4 mA
-200˚C
325˚C
(+)
Dimensions
No Connection
Series Signal
(if sensor hasFC
4 leads,
only connectConditioners
one lead to +)
(-)
(COM)
850˚C
Input Temperature - PT100 type RTD
Red (if applicable)
Output Current
Output Current
12 mA
Linearity Error
DL205
D4
Maximum Loop Supply
30 V DC
0 Ω minimum
Load Impedance
Maximum Load/Power Supply 203 Ω/12 V, 745 Ω/24 V
20 mA
DL05/06
(+)
No Connection
(if sensor has 4 leads,
only connect one lead to +)
(-)
(COM)
850˚C
RTD Signal Condition
Only Use Th
Input Temperature - PT100 type RTD
The specifications and prices described in this catalog were valid when the catalog was issued.
For the latest information, contact our sales persons or see our website.
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
305
Programmable Logic Controller
PLC
HMI
SENSOR
ENCODER
Process Control
FC Series Signal Conditioners
■Potentiometer Input, Analog Output Signal Conditioner
FC-P3
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
Specifications
Items
Specifications
DL05/06
Input Ranges
0 - 100 ohms up to 0-100 kilohms,
3-wire potentiometer/slide-wire
D4
Programmable Range
Minimum
Pushbutton Adjustable to 10% of full range of
applied potentiometer
D3
Excitation
External Power Required
>100 uA @ 2.5 V DC
24 V DC ±10% @ 120 mA, Class 2
Output
DL205
Programmer
DirectSOFT
Terminator I/O
Process Control
ZIP LINK
Output Ranges
0-5 V, 0-10 V, 0-20 mA, 4-20 mA
(DIP Switch Selectable/Invertable)
Maximum Output Current
Response Time
21 mA (for mA OUT ONLY)
35 ms for mA Out, 100 ms for V Out
Load Impedance
2 kilohm minimum, voltage output
550 ohms maximum current output
Output Drive
Voltage: 10 mA maximum
Current: 21 mA maximum
Maximum Inaccuracy
±0.75% @ 0-60˚C, FSO maximum
Output Stability and
Repeatability
0.05% FSO maximum
Output Ripple
Output Protection
Inverted Outputs
0.05% of full scale
Outputs short circuit protected
Invert Outputs using DIP Switch 6
Terminal Block
Removable Screw Terminal Blocks (included)
Field Wiring
Features
Specifications
Dimensions
FC Series Signal
Conditioners
Number of Positions
2 (Dinkle EC350V-02P), 4 (Dinkle EC350V-04P),
4 (Dinkle EC350V-04P)
Wire Range
28-14 AWG solid or stranded conductor;
wire strip length 1/4”(6-7 mm)
Screw Torque
Input Terminal Block
External Power
Terminal Block
Output Terminal
Block
1
2
3
4
24 V
0V
I+
IV+
V-
1.7 inch-pounds (0.19 NM)
Pot End Terminal
Pot Wiper
Pot End Terminal
Shield Connection
24 V DC or 24 V AC ±10%, Class 2
0V
Current
Current
Voltage
Voltage
General
Humidity
5 to 95% (non-condensing)
IEC 60068-2-30 (Test Db, Damp Heat)
Environmental Air
No corrosive gases permitted
(EN61131-2 pollution degree 1)
Vibration
Shock
MIL STD 810C 514.2
MIL STD 810C 516.2
Isolation
1,500 V DC Input to Output
1,000 V DC Power to Input
1,000 V DC Power to Output
applied for 1 second (100% tested)
Insulation Resistance
306
Noise Immunity
NEMA ICS3-304
IEC 61000-4-2 (ESD)
Impulse 1,000 V @ 1μS pulse
IEC 6100-4-4 (FTB)
RFI, (145 MHz, 440 MHz 5W @ 15 cm)
IEC 61000-4-3 (RFI)
Weight
Agency Approvals
0.25 lbs
UL508*, File Number: E157382, CE
Input
* In order to comply with UL508, the supplied power must be less than 26 V DC and fused at a
maximum of 3 amps.
Overview
The FC-P3 is a resistive input to isolated analog output signal conditioner.
The input resistive range (high end resistivity, low end resistivity) is set
through the use of a pushbutton programming routine.
The FC-P3 is field configurable for 3-wire potentiometer/slidewire inputs
with end-to-end resistance ranges from 0-100 ohms to 0-100 kilohms. The
input adjustment range can be scaled down to a minimum of 10% of the
potentiometer being used. Switch selectable, analog output options include
0-20 mA, 4-20 mA, 0-5V, and 0-10 V. The PGM LED provides an indication
of operating status and is used during the field programming process.
The MAX and MIN LED's indicate OVER and UNDER range status. The
module can be 35 mm DIN rail or side mounted and is UL listed. Power for
the unit is provided by a customer supplied 24 V AC or 24 V DC Class 2
power supply.
Application
Use the FC-P3 to eliminate the challenge of getting a variable set by a
machine operator into the PLC. Using the FC-P3 to convert the resistive
signal from a 10 kilohm potentiometer to a 4-20 mA signal that can be used
by a PLC is simple.
Wiring Diagram
RUN/CAL LED
OVER Range LED
IN
ANALOG
4CH
UNDER Range LED
GENERAL CATALOG 2016
DIP Switch
Input DIP 1 2 3 4 5 6 7 8
Setup 0 0 0 0 0 0 1 1
10 kilohm Pot
12345678
F2-04AD-1
18-26.4VDC
80mA
ANALOGIN
4-20mA
0V
+24 V
CH1CH1+
CH2CH2+
CH1CH1+
CH2CH2+
F2-04AD1
DIP Switches
24 V
20
Out 12
(mA)
4-20 mA
4
0
5
10
Input (kΩ)
PLC Analog Input Module
>10 M ohm @ 500 V DC
KOYO ELECTRONICS INDUSTRIES CO., LTD.
Set For
4-20 mA / 2-10 V Output Ranges
Latest catalog (free) is available online.
NOTE: Pot must be wired so that the minimum Pot
resistance is between Input Terminals 1 & 2.
Visit our website ▼
http://www.koyoele.co.jp/english/
Programmable Logic Controller
Process Control
FC Series Signal Conditioners
PLC
HMI
SENSOR
ENCODER
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
DL05/06
DL205
D4
D3
Programmer
DirectSOFT
Terminator I/O
Process Control
ZIP LINK
Features
Specifications
Dimensions
FC Series Signal
Conditioners
The specifications and prices described in this catalog were valid when the catalog was issued.
For the latest information, contact our sales persons or see our website.
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
307
Programmable Logic Controller
PLC
HMI
SENSOR
ENCODER
Process Control
FC Series Signal Conditioners
■Unipolar Voltage or Current to Bipolar Voltage Signal Conditioner
FC-35B
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
Specifications
Items
Specifications
DL05/06
DL205
D4
D3
Input
Terminator I/O
Process Control
410 kilohm voltage input, 250 ohm current input
Polarity Protection Diode
24 V DC ±10%, 40 mA, Class 2
* In order to comply with UL508, the supplied power must be less than 26 V DC and fused at a
maximum of 3 amps.
User Calibration Range
OFFSET (zero): 0-20% (e.g. 0-1.0 V / 5 V mode)
SPAN (full-scale): 80-102% (e.g. 4.0 - 5.1 V / 5 V mode)
Overview
Output Ranges
Load Impedance
Sample Duration Time
Maximum Inaccuracy
Accuracy vs. Temperature
Output Current
±50 mV/±100 mV @ 2.5 μA max,
±5 V, ±10 V, ±15 V @ 7.5 μA max
Number of Positions
2 (Dinkle: EC350V-02P), 3 (Dinkle: EC350V-03P),
6 (Dinkle: EC350V-06P)
Wire Range
28-14 AWG solid or stranded conductor;
wire strip length 1/4”(6-7 mm)
The FC-35B is a 35 mm DIN-rail or side-mount, selectable unipolar input
to bipolar output signal conditioner with isolation between input and output,
and isolation between 24-volt power and input/output. The FC-35B field
configurable isolated signal conditioner is useful in eliminating ground loops
and interfacing sensors to PLC analog input modules. It translates unipolar
voltage inputs or current inputs to bipolar voltage outputs. The input and
output signal levels are selected via DIP switches. In addition, the outputs
can be either a direct conversion of the inputs or an inversion (a reverse
acting operation).
The user also has the option of customizing the input OFFSET (zero) and
SPAN (full scale) adjustments that can be set to a percentage of the full scale
via a pushbutton on the front panel.
1.7 inch-pounds (0.19 Nm)
Switch/LED Labels
Diagnostic LED flashing indication
Push button switch input to initiate calibration, etc.
General
DIAG
CAL
Specifications
308
Output
±50 mV, ±100 mV, ±5V, ±10 V, ±15 V
2 kilohm Minimum
10 ms
0.1% FSO @ 25˚C (1.0% 50 mV / 100 mV)
±60 PPM of Full Scale / ˚C Maximum
Terminal Block
Removable Screw Type Terminal Blocks (Included)
Screw Torque
FC Series Signal
Conditioners
UL508*, File Number: E157382, CE
Input Impedance
Protection Type, Component
External DC Power Required
Field Wiring
Dimensions
Agency Approvals
0-5V, 0-10 V, 0-20 mA, 4-20 mA
(DIP Switch Selectable/Invertable)
ZIP LINK
Features
1,800 V DC Power to Input
1,800 V DC Power to Output
1,800 V DC Input to Output
applied for 1 second (100% tested)
Input Ranges
Programmer
DirectSOFT
Isolation
Surrounding Air Temperature
0 to 60˚C (32 to 140˚F)
IEC 60068-2-14 (Test Nb, Thermal Shock)
Storage Temperature
-20 to 70˚C (-4 to 158˚F)
IEC 60068-2-1 (Test Ab, Cold)
IEC 60068-2-2 (Test Bb, Dry Heat)
IEC 60068-2-14 (Test Na, Thermal Shock)
Enclosure Rating
IP20
Humidity
5 to 95% (non-condensing)
IEC 60068-2-30 (Test Db, Damp Heat)
Environmental Air
No corrosive gases permitted
(EN61131-2 pollution degree 1)
Vibration
MIL STD 810C 514.2
IEC 60068-2-6 (Test Fc)
Shock
MIL STD 810C 516.2
IEC 60068-2-27 (Test Ea)
Insulation Resistance
> 10 M @ 500 V DC
Noise Immunity
NEMA ICS3-304
IEC 61000-4-2 (ESD)
Impulse 1,000 V @ 1μS pulse
IEC 61000-4-4 (FTB)
RFI, (145 MHz, 440 MHz 5W @ 15 cm)
IEC 61000-4-3 (RFI)
Weight
0.3 lbs
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
Latest catalog (free) is available online.
Visit our website ▼
http://www.koyoele.co.jp/english/
Programmable Logic Controller
Process Control
FC Series Signal Conditioners
PLC
HMI
SENSOR
ENCODER
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
Application Example 1
Application Example 2
SJ
Use the FC-35B to convert a unipolar output from a PLC analog card to a
bipolar ±10 V DC signal to control a SureServo's External Velocity Command.
Use the FC-35B to convert and isolate a unipolar output from a 4-20 mA
sensor or transmitter to a bipolar ± 10 V DC signal for a PLC input.
DL05/06
DL205
4-20
4-20mA
mA
OUT
OUT
24
24VV
DIP
DIPSwitch
Switch
ANALOG
ANALOG
2CH
2CH
FC-35B
FC-35B
DIP
DIPSwitch
Switch
Input
InputDIP
DIP 11 22 33 44 55 66 77 88
Setup
Setup 00 00 11 00 00 00 11 00
FC-35B
FC-35B
V+
V+
F2-02DA-1
F2-02DA-1
V+
V+
24
24VV
00VV
Out
Out
(V)
(V)
-10
-10
44
IN
IN
12
12
ANALOG
ANALOG
4CH
4CH
Programmer
24
24VV
00VV
20
20
Input
Input(mA)
(mA)
±mV
±mV
±10
±10VV
±15
±15VV
COM
COM
PLC
PLCAnalog
AnalogOutput
OutputModule
Module
Set
SetFor
For
4-20
4-20mA
mAInput
Input
±10
±10VVOutput
Output
++
--
±10
±10VV
Analog
Analog
Input
Input
SureServo
SureServoTMTM
Drive
Drive
DirectSOFT
00
-10
-10
44
12
12
20
20
COM
COM
10-30
10-30V VDC
DC
5mA
5mA
±10
±10VV
00VV
+24
+24VV
CH1-CH1-CH1+
CH1+
CH2-CH2-CH2+
CH2+
CH3-CH3-CH3+
CH3+
CH4-CH4-CH4+
CH4+
Terminator I/O
±mV
±mV
COM
COM
±5
±5VV
Out
Out
(V)
(V)
Input
Input(mA)
(mA)
F2F2-04AD-04AD-2
-2
D3
10
10
CAL
CAL
00
D4
DIP
DIPSwitches
Switches
COM
COM
DIAG
DIAG
10
10
CAL
CAL
±10
±10VV
1122334455667788
I+I+
4-20
4-20mA
mA
DIAG
DIAG
00VV
+24
+24VV
CH1CH1CH1+
CH1+
CH2CH2CH2+
CH2+
NC
NC
NC
NC
NC
NC
NC
NC
*CAUTION:
*CAUTION:Product
Productmay
maybe
bedamaged
damagedifif
multiple
multipleoutputs
outputsare
aretied
tiedtogether.
together.
DIP
DIPSwitches
Switches
COM
COM
18-30
18-30V VDC
DC
6060mA
mA
ANALOG
ANALOGOUT
OUT
4-20
4-20mA
mA
F2-02DA-1
F2-02DA-1
4-20
4-20mA
mA
Transmitter
TransmitterSignal
Signal
1122334455667788
I+I+
4-20
4-20mA
mA
Input
InputDIP
DIP 11 22 33 44 55 66 77 88
Setup
Setup 00 00 11 00 00 00 11 00
±5
±5VV
Process Control
±10
±10VV
±15
±15VV
COM
COM
ZIP LINK
24
24VV
Set
SetFor
For
4-20
4-20mA
mAInput
Input
±10
±10VVOutput
Output
ANALOG
ANALOGININ
0-5,0-10
0-5,0-10V VDC
DC
+/-5,+/-10
+/-5,+/-10V VDC
DC
Set
SetFor
For±10
±10VV
PLC
PLCAnalog
AnalogInput
InputModule
Module
*CAUTION:
*CAUTION:Product
Productmay
maybe
bedamaged
damagedififmultiple
multipleoutputs
outputsare
aretied
tiedtogether.
together.
Features
Specifications
Dimensions
FC Series Signal
Conditioners
The specifications and prices described in this catalog were valid when the catalog was issued.
For the latest information, contact our sales persons or see our website.
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
309
Programmable Logic Controller
PLC
HMI
SENSOR
ENCODER
Process Control
FC Series Signal Conditioners
■Bipolar Voltage to Unipolar Voltage or Current Signal Conditioner
FC-B34
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
Specifications
Items
Specifications
DL05/06
DL205
D4
Input Ranges
±15 V, ±10 V, ±5V, ±100 mV, ± 50 mV
(DIP Switch Selectable)
Input Impedance
Protection Type, Component
External DC Power Required
2 M ohm
Polarity Protection Diode
24 V DC ±10%, 50 mA, Class 2
User Calibration Range
OFFSET (zero): 0-20% (e.g. -4 V/±5 V mode)
SPAN (full-scale): 80-102% (e.g. 4.0 - 5.1 V/±5 V
mode)
D3
Programmer
Output
DirectSOFT
Terminator I/O
Process Control
ZIP LINK
Output Ranges
0-5 V, 0-10 V, 0-20 mA, 4-20 mA
(DIP Switch Selectable)
Load Impedance
2 kilohm Minimum, Voltage Output
550 ohm Maximum, Current Output
Sample Duration Time
10 ms
Maximum Inaccuracy
0.1% FSO (±15 V, ±10 V, ±5 V Inputs),
1.5% FSO ( ±100 mV, ±50 mV Inputs) @ 25˚C
Accuracy vs. Temperature
+/-60 PPM of Full Scale/ ˚C Maximum
Output Current
21 mA max for mA-Out mode/
10 mA max for Volt-out mode
Terminal Block
Removable Screw Type Terminal Blocks, (included)
Field Wiring
Features
Number of Positions
2 (Dinkle: EC350V-02P), 2 (Dinkle: EC350V-02P),
4 (Dinkle: EC350V-04P)
Wire Range
28-14 AWG solid or stranded conductor;
wire strip length 1/4" (6-7 mm)
Specifications
Screw Torque
Dimensions
DIAG
CAL
FC Series Signal
Conditioners
310
Weight
0.3lbs
Isolation
1,800 V DC Power to Input
1,800 V DC Power to Output
1,800 V DC Input to Output
applied for 1 second (100% tested)
Agency Approvals
UL508*, File Number: E157382, CE
Input
* In order to comply with UL508, the supplied power must be less than 26 V DC and fused at a
maximum of 3 amps.
Overview
The FC-B34 is a 35 mm DIN-rail or side-mount, selectable bipolar input to
unipolar output signal conditioner with isolation between input and output,
and isolation between 24-volt power and input/output. The FC-B34 field
configurable isolated signal conditioner is useful in eliminating ground loops
and interfacing sensors to PLC analog input modules. It translates bipolar
voltage input to unipolar voltage output or bipolar voltage input to a current
output. The input and output signal levels are selected via DIP switches.
In addition, the outputs can be either a direct conversion of the inputs or
an inversion (a reverse acting operation). The user also has the option of
customizing the input OFFSET (zero) and SPAN (full scale) adjustments that
can be set to a percentage of the full scale via a pushbutton on the front
panel.
1.7 inch-pounds (0.19 Nm)
Switch/LED Labels
Diagnostic LED flashing indication
Pushbutton switch input to initiate calibration, etc.
General
Surrounding Air Temperature
0 to 60˚C (32 to 140˚F)
IEC 60068-2-14 (Test Nb, Thermal Shock)
Storage Temperature
-20 to 70˚C (-4 to 158˚F)
IEC 60068-2-1 (Test Ab, Cold)
IEC 60068-2-2 (Test Bb, Dry Heat)
IEC 60068-2-14 (Test Na, Thermal Shock)
Enclosure Rating
IP20
Humidity
5 to 95% (non-condensing)
IEC 60068-2-30 (Test Db, Damp Heat)
Environmental Air
No corrosive gases permitted
(EN61131-2 pollution degree 1)
Vibration
MIL STD 810C 514.2
IEC 60068-2-6 (Test Fc)
Shock
MIL STD 810C 516.2
IEC 60068-2-27 (Test Ea)
Insulation Resistance
>10 MΩ@ 500 V DC
Noise Immunity
NEMA ICS3-304
IEC 61000-4-2 (ESD)
Impulse 1,000 V @ 1μS pulse
IEC 61000-4-4 (FTB)
RFI, (145 MHz, 440 MHz 5W @ 15 cm)
IEC 61000-4-3 (RFI)
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
Latest catalog (free) is available online.
Visit our website ▼
http://www.koyoele.co.jp/english/
Programmable Logic Controller
Process Control
FC Series Signal Conditioners
PLC
HMI
SENSOR
ENCODER
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
Application Example 1
The FC-B34 can be used to convert a bipolar ±10 V DC signal to a 4-20 mA
signal.
IN
SJ
The FC-B34 can be used to convert the bipolar ±10 V DC from a DCT10010B-24S current transducer to a 4-20 mA or 0-10 V DC that can be used by
a PLC.
DL05/06
ANALOG
ANALOG
4CH
PLC Analog Output Module
4CH
PLC Analog Output Module
F2--02DA--2
F2--02DA--2
0V
0V
+24 V
+24 V
CH1-CH1-CH1+
CH1+
CH2-CH2-CH2+
CH2+
CH3 CH3 CH3+
CH3+
CH4 CH4 CH4+
CH4+
DIAG
DIAG
CAL
+24 V
+24 V
0V
0V
4-20 mA
4-20 mA
Current
Current
Device
Device
24 V
24 VPower
Power
Supply
Supply
I+
IV+
V-
CAL
I+
IV+
V-
IN
IN
DIP Switch
DIP Switch
Input DIP 1 2 3 4 5 6 7 8
Input DIP
1 2 13 04 05 06 17 18 0 0
Setup
Setup 1 0 0 0 1 1 0 0
12345678
12345678
DIP Switches
DIP Switches
24 V
24 V
0V
0V
ANALOG IN
0-5, 0-10 V DC
ANALOG IN
0-5, 0-10 +/-5,
V DC +/-10 V DC
+/-5, +/-10 V DC
Set for ±10 V Output
Set for ±10 V Output
FC-B34
FC-B34
V+
V+
VV-
±10 V
±10 V
10-30 V DC
5 mA
10-30 V DC
5 mA
Set for
Set±10
for V Input
±10 V Input
and
and mA Output
4-20
4-20 mA Output
1 2 3 4
1 POWER
2 3 4 OUTPUT
±10 V DC
24 V ACDC
POWER
OUTPUT
24 V ACDC ±10 V DC
IN
Application Example 2
20
20
OUT 12
OUT (mA)
12
(mA)
4
4
-10
-10
0
+10
0
+10
INPUT (V)
INPUT (V)
ANALOG
ANALOG
4CH
4CH
FC-B34
FC-B34
V+
V+
VV-
F2--04AD--1
F2--04AD--1
CAL
0V
0V
+24V
+24V
CH1-CH1-CH1+
CH1+
CH2-CH2-CH2+
CH2+
CH3-CH3-CH3+
CH3+
CH4-CH4-CH4+
CH4+
ANALOG IN
4-20 mA
ANALOG IN
4-20 mA
12345678
12345678
DIP Switches
DIP Switches
DIAG
DIAG
10-30 V DC
10-30 V DC 5 mA
5 mA
*CAUTION: If current output (I+/I-) and Voltage output (V+/V-)
*CAUTION: If current
output
(I+/I-) and
outputthe
(V+/V-)
are both
connected
toVoltage
loads and/or
“I+” terminal
are both
connected
to loads
and/or
the “I+”may
terminal
to the
“V-” terminal,
product
damage
occur.
to the “V-” terminal, product damage may occur.
DIP Switch
DIP Switch
Input DIP 1 2 3 4 5 6 7 8
Input DIP
1 2 03 04 05 06 17 18 0 0
Setup
Setup 0 0 0 0 1 1 0 0
CAL
24 V
24 V
0V
0V
I+
IV+
V-
I+
IV+
V-
DL205
D4
D3
Programmer
DirectSOFT
Terminator I/O
Process Control
ZIP LINK
(-)(+)
(-)(+)Power
Power
Supply
Supply
Features
Specifications
Dimensions
FC Series Signal
Conditioners
The specifications and prices described in this catalog were valid when the catalog was issued.
For the latest information, contact our sales persons or see our website.
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
311
Programmable Logic Controller
PLC
HMI
SENSOR
ENCODER
Process Control
FC Series Signal Conditioners
■Encoder Signal Conditioner and Optical Isolator - Open Collector Output
FC-ISO-C
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
Specifications
Items
DL205
D4
Input
Input Voltage
(DIP selectable)
4.5-7.5 V DC
12-26 V DC
10 W (maximum power with all outputs at max
current and max voltage)
Thermal Dissipation
Isolation
Mounting
34.13 BTU/hr (1 W = 3.413 BTU/hr)
1,800 V AC input-output applied for 1 second
35 mm DIN Rail or panel mount (with no restrictions)
Operating Temperature
0 to 60˚C (32 to 140˚F)
IEC 60068-2-14 (Test Nb, Thermal Shock)
Storage Temperature
-20 to 70˚C (-4 to 158˚F)
IEC 60068-2-1 (Test Ab, Cold)
IEC 60068-2-2 (Test Bb, Dry Heat)
IEC 60068-2-14 (Test Na, Thermal Shock)
Humidity
5 to 95% (non-condensing)
IEC 60068-2-30 (Test Db, Damp Heat)
Environmental Air
No corrosive gases permitted
(EN61131-2 pollution degree 1)
Vibration
MIL STD 810C 514.2
IEC 60068-2-6 (Test Fc)
Shock
MIL STD 810C 516.2
IEC 60068-2-27 (Test Ea)
Insulation Resistance
>10 MΩ @ 500 V DC
Noise Immunity
NEMA ICS3-304
IEC 61000-4-2 (ESD)
Impulse 1,000V @ 1μS pulse
IEC 61000-4-4 (FTB)
RFI, (145MHz, 440MHz 5W @ 15cm)
IEC 61000-4-3 (RFI)
Weight
Agency Approvals
0.3 lbs
UL*, cUL (File # E157382), CE
Protection Type, Component
Switching Threshold“0”
Signal
< 2.2 V DC
< 3.9 V DC
Programmer
Switching Threshold“1”
Signal
> 2.6 V DC
> 4.8 V DC
Output Circuit
Open collector: 2-wire - floating or pull-up
(DIP switch selectable); Sinking
Output Rating
Continuous Output Current
5-36 V DC
65 mA maximum
Overcurrent Trip Level
76 mA minimum
Quiescent Current
Output Voltage Protection
25 μA maximum
Polarity reversal, surge voltage protection
Output Current Protection
Short circuit/Over Current/Over Current Limiting/
Thermal Shutdown
DirectSOFT
ZIP LINK
Power Dissipation Within
Module
9 mA typical, 18 mA maximum
D3
Process Control
General
7.8-24 V DC ± 10% @ 125 mA, 3.5 W*
Input Current
Surge, Suppressor Diode; Over current/temperature,
Microprocessor
Terminator I/O
External DC Power Required
Specifications
DL05/06
Output
Timing
Input to Output Response
Time
1.3 μs (max w/ 4.7 k ohm internal pull-up resistor)
Features
Output Timing Difference
(Ch. to Ch. Lag)
< 20 ns channel to channel (max)
Specifications
Rise Time
(tON w/ 1 k ohm Load)
250 ns
Dimensions
Fall Time
(toff w/ 1 k ohm Load)
38 ns
FC Series Signal
Conditioners
Max Frequency Response w/
1 MHz
1k ohm Load
Rise Time
(ton w/ 2.2 k ohm Load)
512 ns
Fall Time
(toff w/ 2.2 k ohm Load)
56 ns
Max Frequency Response w/
750 kHz
2.2 k ohm Load
Rise Time (ton w/ 4.7 k
Internal Pull-Up)
1.2μs
Fall Time (toff w/ 4.7 k
Internal Pull-Up)
25 ns
Max Frequency Response w/
200 kHz
4.7 k Internal Pull-Up
Terminal Block
312
Number of Positions
2 pole (Dinkle: EC350V-02P),
8 pole (Dinkle: EC350V-08P)
Wire Range
28-16AWG Solid or Stranded Conductor; Wire strip
length 9/32”(6-7 mm)
Screw Size (Slotted)
M 2.5 size, 0.4 T x 2.5 W mm
(Screwdriver part number DN-SS1)
Screw Torque
1.7 inch-pounds (0.19 Nm)
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
* In order to comply with UL508 the supplied power must be less than 26 V DC and fused at a
maximum of 3 amps.
Overview
The FC-ISO-C high speed optical isolator module has the versatility to solve
various interface problems between an incremental encoder signal and
a PLC, servo drive, or other input device. Ideal for use with single-ended
(open collector, NPN, pull-up, push-pull, totem pole) or differential line driver
encoder signals, the three complementary inputs (A, B, Z, A-not, B-not,
Z-not) are rated for 4.5-7.5 V DC and 12-26 V DC and frequency response up
to 1 MHz. Input terminals A, B, and Z can be internally connected together
and complementary input terminals A-not, B-not, and Z-not can be internally
connected to common through DIP switches for simplified wiring.
The FC-ISO-C has three complementary open collector outputs (A, B, Z,
A-not, B-not, Z-not) rated for 5-36 V DC that can be used in single ended
configurations. The open collector output terminals can be connected to
internal pull-up resistors through DIP switches for quick troubleshooting.
Optical isolation rated at 1,800 V separates the input signals from the
outputs. The slim-line plastic housing includes an integral 35 mm DIN rail
mounting adapter, LED indication, and removable screw terminal blocks for
easy installation and wiring. The FC-ISO-C module is UL508 listed and CE
marked.
Latest catalog (free) is available online.
Visit our website ▼
http://www.koyoele.co.jp/english/
Programmable Logic Controller
Process Control
FC Series Signal Conditioners
PLC
HMI
SENSOR
ENCODER
COUNTER
INFORMATION
Common
Subject Matter
ISOLATION
BARRIER
OK
Application
A
B
FC-ISO-C
A Pulse
B Pulse
+Ai
-Ai
+Bi
-Bi
+Zi
-Zi
COM
COM
SureServo
V+
0V
+
Fuse
OA
/OA
OB
/OB
OZ
/OZ
Fuse
CN1
Y0
SJ
Y1
OUT
A
B
C
D
M
YC
Y0
Y1
OUT
H0-CTRIO
7.5-24 V DC±10%
- Provide optical isolation between an encoder signal and PLC, servo drive,
or other input device
- Solve electrically noisy signal problems
- Use as a repeater to allow longer cable runs
- Convert a differential line driver encoder signal to an open collector singleended signal
- Change encoder signal voltage to match receiving electronics input
- Ideal for use with encoders, servo drive encoder signal inputs and outputs,
or as a multi-channel, high speed optically isolated interface for sensors
like photoelectric and proximity switches
KOSTAC Safety
AZ-C1
ERR
DL205
D4
D3
PLC High Speed Counter
Interface Module
+
24 V DC
Ao
DL05/06
Ao
Bo
Bo
Programmer
Zo
Zo
Application Example 1
Application Example 2
Convert SureServo line driver Input/Output Terminals (CN1) to a 24 V DC
open collector single ended signal that is compatible with a PLC high speed
counter interface module.
Convert a 5 V DC differential line driver encoder signal to a 24 V DC open
collector singleended signal that is compatible with a PLC high speed counter
interface module.
DirectSOFT
0V
0V
ISOLATION
BARRIER
ISOLATION
BARRIER
A
B
FC-ISO-C
B Pulse
+Ai
-Ai
+Bi
-Bi
+Zi
-Zi
COM
COM
SureServo
V+
0V
+
Fuse
A Pulse
Fuse
OA
/OA
OB
/OB
OZ
/OZ
7.5-24 V DC±10%
CN1
OK
Y0
A
Y1
B
OUT
A
B
C
D
M
YC
Y0
Y1
OUT
H0-CTRIO
Blue: 0 V
Black: OUT A
Differential Line
Driver Encoder
PLC High Speed Counter
Interface Module
Ao
Bo
Bo
-Ai
-Bi
+Zi
COM
Orange: OUT Z
+
+Ai
+Bi
White: OUT B
Yellow: OUT Z
Shield: Ground
-Zi
COM
Zo
Ao
* Use separate power supply to maintain isolation
0V
0V
Bo
Bo
Y0
Y1
Features
Specifications
V+
0V
Ao
Zo
ERR
OUT
A
B
C
D
M
YC
Y0
Y1
OUT
H0-CTRIO
FC-ISO-C
Purple: OUT A
Gray: OUT B
24 V DC
Ao
Brown: Power source*
ENCODER
Process Control
ZIP LINK
ERR
+
PLC High Speed
Counter
Interface Module
24 V DC
OK
Terminator I/O
Zo
Zo
Dimensions
FC Series Signal
Conditioners
0V
0V
ISOLATION
BARRIER
OK
A
B
Blue: 0 V
Black: OUT A
Differential Line
Driver Encoder
+Ai
-Ai
+Bi
-Bi
+Zi
White: OUT B
COM
Gray: OUT B
Orange: OUT Z
-Zi
COM
V+
Yellow: OUT Z
0V
Shield: Ground
Ao
Ao
* Use separate power supply to maintain isolation
Bo
Bo
Y1
OUT
A
B
C
D
M
YC
Y0
Y1
OUT
H0-CTRIO
FC-ISO-C
Purple: OUT A
Y0
+
PLC High Speed
Counter
Interface Module
24 V DC
Brown: Power source*
ENCODER
ERR
Zo
Zo
0V
0V
The specifications and prices described in this catalog were valid when the catalog was issued.
For the latest information, contact our sales persons or see our website.
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
313
Programmable Logic Controller
PLC
HMI
SENSOR
ENCODER
Process Control
FC Series Signal Conditioners
■Encoder Signal Conditioner and Optical Isolator - Differential Line Driver Output
FC-ISO-D
COUNTER
INFORMATION
Common
Subject Matter
KOSTAC Safety
AZ-C1
SJ
Specifications
Items
Specifications
DL05/06
DL205
External DC Power Required
Input
Input Voltage
(DIP selectable)
4.5-7.5 V DC
12-26 V DC
Input Current
7.5 mA typical, 14 mA maximum
Protection Type, Component
Output Short Circuit Protection, Output Current
Limiting, Output Thermal Shutdown, 15 kV ESD
protection; Differential Driver Chip
Programmer
Switching Threshold“0”
Signal
< 2.2 V DC
< 3.9 V DC
DirectSOFT
Switching Threshold“1”
Signal
> 2.6 V DC
> 438 V DC
D4
D3
Terminator I/O
Process Control
ZIP LINK
Output Circuit
Output
Continuous Output Current
Overcurrent Level
Quiescent Current
Output
Differential line drive; Sourcing
5 V DC
70 mA maximum
Limited to 70 mA
1.0 mA maximum
Output Voltage Protection
None (not reverse polarity protected); Voltage less
than -9 V or greater than 14 V will damage chip
Voltage Drop at Max
Continuous Current
1.75 V DC
Output Current Protection
Short Circuit, Current Limiting, Thermal Shutdown, 15
kV ESD Protection
Features
Input to Frequency
Response Time
1.3 μs
Specifications
Output Timing Difference
(Ch. to Ch. Lag)
< 20 ns
Dimensions
Output Rise Time (ton)
Output Fall Time (toff )
Max Frequency Response
Timing
FC Series Signal
Conditioners
314
General
24 V DC ±10% @ 105 mA*
Power Dissipation Within
Module
9W (all outputs at max current at max voltage)
Thermal Dissipation
Isolation
Mounting
30.72 BTU/hr (1W = 3.413 BTU/hr)
1,800 V AC input-output applied for 1 second
35 mm DIN Rail or panel mount (with no restrictions)
Operating Temperature
0 to 60˚C (32 to 140˚F)
IEC 60068-2-14 (Test Nb, Thermal Shock)
Storage Temperature
-20 to 70˚C (-4 to 158˚F)
IEC 60068-2-1 (Test Ab, Cold)
IEC 60068-2-2 (Test Bb, Dry Heat)
IEC 60068-2-14 (Test Na, Thermal Shock)
Humidity
5 to 95% (non-condensing)
IEC 60068-2-30 (Test Db, Damp Heat)
Environmental Air
No corrosive gases permitted
(EN61131-2 pollution degree 1)
Vibration
MIL STD 810C 514.2
IEC 60068-2-6 (Test Fc)
Shock
MIL STD 810C 516.2
IEC 60068-2-27 (Test Ea)
Insulation Resistance
>10 MΩ @ 500 V DC
Noise Immunity
NEMA ICS3-304
IEC 61000-4-2 (ESD)
Impulse 1,000V @ 1μS pulse
IEC 61000-4-4 (FTB)
RFI, (145MHz, 440MHz 5W @ 15cm)
IEC 61000-4-3 (RFI)
Agency Approvals
UL*, cUL (File # E157382), CE
< 15 ns
< 15 ns
1 MHz
Terminal Block
* In order to comply with UL508 the supplied power must be less than 26 V DC and fused at a
maximum of 3 amps.
Number of Positions
2 pole (Dinkle: EC350V-02P),
8 pole (Dinkle: EC350V-08P)
Wire Range
28-16 AWG Solid or Stranded Conductor; Wire strip
length 5/16”(7-8mm)
Screw Size (Slotted)
M 2.5 size, 0.4 T x 2.5 W mm
(Screwdriver part number DN-SS1)
Screw Torque
1.7 inch-pounds (0.19 Nm)
The FC-ISO-D high speed optical isolator module has the versatility to solve
various interface problems between an incremental encoder signal
and a PLC, servo drive, or other input device. Ideal for use with single-ended
(open collector, NPN, pull-up, push-pull, totem pole) or differential line driver
encoder signals, the three complementary inputs (A, B, Z, A-not, B-not,
Z-not) are rated for 4.5-7.5 V DC and 12-26 V DC and frequency response up
to 1 MHz. Input terminals A, B, and Z can be internally connected together
and complementary input terminals A-not, B-not, and Z-not can be internally
connected to common through DIP switches for simplified wiring.
The FC-ISO-D has three differential line driver outputs (A, B, Z, A-not, B-not,
Z-not) rated for 5 V DC. Optical isolation rated at 1,800 V separates the input
signals from the outputs. The slim-line plastic housing includes an integral 35
mm DIN rail mounting adapter, LED indication, and removable screw terminal
blocks for easy installation and wiring. The FC-ISO-D module is UL508 listed
and CE marked.
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
Overview
Latest catalog (free) is available online.
Visit our website ▼
http://www.koyoele.co.jp/english/
Programmable Logic Controller
Process Control
FC Series Signal Conditioners
PLC
HMI
SENSOR
ENCODER
COUNTER
INFORMATION
ISOLATION
BARRIER
+
24VDC
FC-ISO-D
+Ai
-Ai
+Bi
-Bi
+Zi
-Zi
COM
COM
Blue: 0 V
Brown: Power source*
Black: OUT A
White: OUT B
Single Ended Open
Collector Encoder
Common
Subject Matter
KOSTAC Safety
AZ-C1
Fuse
SJ
Shield: Ground
* Use separate power supply to maintain isolation
24 V DC
V+
0V
DL05/06
CN1
DIP Switch 1
SIGN
/SIGN
PULSE
/PULSE
VCC
T-REF
GND
PULL HI
Ao
Input DIP 1 2 3 4 5 6 7 8
Setup 0 0 0 0 0 1 1 1
Ao
Bo
Bo
Zo
12345678
Zo
DIP Switches
0V
0V
SureServo
DL205
D4
D3
Programmer
Application Example 1
Convert a 24 V DC single ended open collector encoder signal to a 5 V
DC differential line driver signal compatible with SureServo Input/Output
Terminals (CN1).
ISOLATION
BARRIER
+
24VDC
Application Example 2
DirectSOFT
Convert a 24 V DC single-ended open-collector encoder signal to a 5 V DC
differential line driver signal compatible with the encoder input on a servo
drive.
Terminator I/O
ISOLATION
BARRIER
-
24 V DC
+
FC-ISO-D
Brown: Power source*
Black: OUT A
White: OUT B
SW7
Brown: Power source*
Black: OUT A
White: OUT B
Fuse
Single Ended Open
Collector Encoder
Shield: Ground
CN1
DIP Switch 1
SIGN
/SIGN
PULSE
/PULSE
VCC
T-REF
GND
PULL HI
Ao
Input DIP 1 2 3 4 5 6 7 8
Setup 0 0 0 0 0 1 1 1
Ao
Bo
Bo
Zo
12345678
Zo
DIP Switches
0V
0V
SureServo
Internal
SW7
SW8
Fuse
Shield: Ground
* Use separate power supply to maintain isolation
24 V DC
V+
0V
Orange: OUT Z
+Ai
-Ai
+Bi
-Bi
+Zi
-Zi
COM
COM
SW6
DIP Switch 1
Input DIP 1 2 3 4 5 6 7 8
Setup 0 0 0 0 0 1 1 1
12345678
DIP Switches
V+
0V
Ao
Ao
Bo
Bo
Zo
Zo
0V
0V
24 V DC
-
-
* Use separate power supply to maintain isolation
Blue: 0 V
SW8
+
Orange: OUT Z
ZIP LINK
-
FC-ISO-D
SW6
Internal
Process Control
+
+Ai
-Ai
+Bi
-Bi
+Zi
-Zi
COM
COM
Blue: 0 V
Single Ended Open
Collector Encoder
SW8
-
- Provide optical isolation between an encoder signal and PLC, servo drive,
or other input device
- Solve electrically noisy signal problems
- Use as a repeater to allow longer cable runs
- Convert a single ended encoder signal to a differential line driver signal
- Convert a differential line driver encoder signal to a single-ended signal
- Change encoder signal voltage to match receiving electronics input
- Ideal for use with encoders and servo drive encoder signal inputs and
outputs
SW7
+
Application
Orange: OUT Z
SW6
Internal
Servo Drive
Encoder Input
A
A/
B
B/
Z
Z/
GND
Features
Specifications
Dimensions
FC Series Signal
Conditioners
ISOLATION
BARRIER
24 V DC
+
-
FC-ISO-D
Blue: 0 V
Brown: Power source*
Black: OUT A
White: OUT B
Orange: OUT Z
Internal
SW6
SW7
SW8
Fuse
+
Single Ended Open
Collector Encoder
+Ai
-Ai
+Bi
-Bi
+Zi
-Zi
COM
COM
Shield: Ground
DIP Switch 1
Input DIP 1 2 3 4 5 6 7 8
Setup 0 0 0 0 0 1 1 1
12345678
V+
0V
Ao
Ao
Bo
Bo
Zo
Zo
24 V DC
-
* Use separate power supply to maintain isolation
Servo Drive
Encoder Input
A
A/
B
B/
DIP Switches
0V
The specifications and
prices described in this
catalog were valid
when the catalog was issued.
Z
0V
Z/
For the latest information, contact our sales persons or see our website.
GND
KOYO ELECTRONICS INDUSTRIES CO., LTD.
GENERAL CATALOG 2016
315