(34429)
Introducing ...
Tresco® Remote Control LED Dimmer
Tresco® International introduces a new remote control electronic Dimmer for use on LED
lighting systems. The Tresco LED Dimmer features radio frequency, remote control
dimming to adjust lights from anywhere in the room - up to 9 meters (30 feet). The
Remote Control provides on/off power and dims lights from 1%–100%. Each Dimmer
comes with two Remote Controls to control the Dimmer and its run of lights.
Wire
contacts
33 mm
1-5/16 in.
57 mm
2-1/4 in.
81 mm
3-3/16 in.
29 mm
1-1/8 in.
57 mm
2-1/4 in.
Mounting
tab
(2) Remote
Controls
Remote Control LED Dimmer
P/N: LED-DIMRMT-12V8A
Tresco International’s LED Electronic Dimmer:
• Controls up to 8 amps / 96 Watts of LED lighting.
• Can be used with either 18W or 60W DC Transformers.
• Features a built-in memory that recalls the last setting when
turned on again.
• Comes with two Remote Controls (one extra, as a backup) that
are synchronized to control the same Dimmer.
• Can use multiple Dimmers in the same room with independent
controlling of each.
innovation meets illumination
®
RTD10000786AA
LED Dimmers Installation:
Tresco® LED Dimmers are installed on the 12V side of the DC
Transformer. LED Dimmers can be installed in several different
configurations. Below are two typical installation applications.
Installation Option #1
4. Cut-off AMP® connector on Mounting Block and strip 6mm (1/4”)
insulation from wire.
(To dim all lights on the system)
1. Disconnect Transformer from Mounting Block.
2. Cut-off AMP® connector from Transformer. Strip 6mm (1/4”) insulation
from wire.
5. Connect brown wire (+) from Mounting Block to red input (+) of Dimmer,
connect blue wire (–) from Mounting Block to black input (–) of Dimmer.
6. Plug LED lights into Mounting Block. (see LED light’s installation
instructions for further information)
3. Connect brown wire (+) from Transformer to red input (+) of Dimmer,
connect blue wire (–) from Transformer to black input (–) of Dimmer.
LED Dimmer
DC Transformer
•+
•–
Mounting Block
•
–•
+
INPUT
OUTPUT
12V side of
Transformer
120V side of
Transformer
Installation Option #2
(To dim a single light or single run of lights)
1. Transformer stays connected to Mounting Block.
2. Choose length of Linking Cord D (purchased separately). Push needle
terminals of Linking Cord D into male AMP® connector (provided
w/Linking Cord D). Then plug AMP connector into Mounting Block.
3. Cut-off female AMP connector from other end of Linking Cord D. Strip
6mm (1/4”) insulation from wire.
4. Connect wire ends of Linking Cord D to LED Dimmer, connect red to
red (+) and black to black (–).
5. Choose length of Linking Cord D (purchased separately) to be used from
output of Dimmer to run of LED lights. Cut-off needle terminals from
wire ends of Linking Cord D. Strip 6mm (1/4”) insulation from wire.
6. Connect wire ends of Linking Cord D to Dimmer, connect red to red
(+) and black to black (–).
7. Connect other end of Linking Cord D to the run of LED lights. (see LED
light’s installation instructions for further information)
Linking Cord D
LED Dimmer
DC Transformer
Linking Cord D
to run of LED lights
Mounting Block
•+
•–
INPUT
120V side of
Transformer
•
–•
+
OUTPUT
In this installation configuration, the additional
slots of the Mounting Block can be used to link
to lights that are not to be dimmed.
12V side of
Transformer
Typical Soffit Installation with Remote Control Dimmer
DC Transformer
LED Dimmer
Mounting Block
®
Linking Cord D
Tresco International Ltd. Co.
Place Distributor
Sticker Here
801 E. Middletown Rd.
North Lima, Ohio, USA 44452
Phone: 1-800-227-1171
330-549-2230
Fax:
330-549-2260
1-800-841-2523
Email: custsvc@trescointl.com
www.trescointernational.com
LEDDim1/310/5m-48h