Location:
FLOOR MOUNTED SERVICE
SINK CARRIER WITHOUT FITTING
MC-61
Specification: MIFAB Series MC-61 floor mounted service sink carrier with two lacquered 2" x 1" x 1/8" thick structural steel
uprights with 3" x 4 ½" welded steel feet, and back outlet waste connection (specify no hub or threaded waste connection).
Complete with lacquered cast iron faceplate assembly, lacquered cast iron nipple and waste connector, adjustable 8" tapered
thread ABS nipple with integral test cap, neoprene bowl gasket, hardware, threaded rod protectors and polished chrome plated
finishing cap nuts.
Function: Used with off the floor wall urinals and service sinks that are wall mounted, and have no contact with the finished
floor. Typically installed in utility, emergency and clean-up rooms where the narrow wall design does not accommodate the
carrier fitting. The closet carrier is completely concealed within the wall and supports the load of the fixture through a faceplate and foot support system that is anchored to the floor. Sanitation underneath the fixture is more efficiently and economically maintained when installed off of the floor compared to floor mounted.
Note: 8” tapered thread ABS nipple
shipped standard with MC-10 Series
“X” = 4 5/8” MIN,
carriers. The universal faceplate
5 3/4” MAX,
assembly accepts all nipple variations,
WITH STANDARD
rolling thread (-OR), cast iron (-CI) and
NIPPLE.
1
1/4”
IS
22"
UNIVERSAL
tapered thread ABS with adjustable
POSSIBLE
"X"
PLATE
horn (-AH).
WITH SHORTENED
ASSEMBLY
SECURED TO
UPRIGHTS
"U" BOLTS TO
SECURE
UNIVERSAL
PLATES TO
UPRIGHT
NIPPLE. FOR
GREATER THAN
STANDARD MAX,
USE LONGER
NIPPLES AND
SPECIFY
DIMENSION
REQUIRED.
36"
LACQUERED CAST IRON NIPPLE
AND WASTE CONNECTOR
ILLUSTRATED WITH 4” F.I.P.
WASTE CONNECTION. SPECIFY -N
FOR 4” NO HUB WASTE
CONNECTION AND USE
THE MI-850-4
EXTRA HEAVY
DUTY RECTANGULAR
STEEL STRUCTURAL
UPRIGHTS
7"
"X"
FACEPLATE
MOUNTING
BRACKETS
3"
MC-61 Series
Meets ANSI/ASME
fixture carrier standard
A112.6.1M-97
300lb. load rating
ABS TAPERED
THREADED NIPPLE
WITH INTEGRAL
TEST CAP
4 1/2"
HEAVY DUTY WELDED
FEET THAT FIT
WITHIN STANDARD STUD WALL CONSTRUCTION
FINISHED WALL
MODEL NUMBER CHART
MC-61-T - 4" F.I.P. waste connection
MC-61-N - 4" No Hub waste connection
Note: Blow-out configuration illustrated; for siphon jet, invert face plate.
Note: See the various fixture dimensional rough-in guides on the www.mifab.com website.
SUFFIX OPTIONAL VARIATIONS
-AH8
-AH12
-BA
-CI-4
-CI-6
-CI-8
-CI-12
-CI-24
-HD
-HD-750
-HDX
N
Job Name:
Section No:
Schedule No:
8" ABS nipple with adjustable horn
12" ABS nipple with adjustable horn
Buy American Act compliant product
4" rolling thread cast iron nipple
6" rolling thread cast iron nipple
8" rolling thread cast iron nipple
12" rolling thread cast iron nipple
24" rolling thread cast iron nipple
Heavy duty 500 lb. load rated carrier
Heavy duty 750 lb. load rated carrier
Extra heavy duty 1,000 lb. load rated carrier
4" no hub waste connection (with MI-850-4)
SUFFIX
OPTIONAL VARIATIONS
-PA
-PFAB
T
-1
-10
Pennsylvania Steel Act compliant product
Prefabricated carrier
4" F.I.P. threaded waste connection
Finishing / Tiling frame
Auxiliary support, recommended with nipple
lengths over 12"
12" tapered thread ABS nipple
Galvanized cast iron
Vandal proof finish trim
Test plug for custom and cast iron nipples
Nipple wrench
Flush valve support
Foot pedal valve mounting table
-12
-13
-14
-17
-19
-20
-32
Page No:
Contract:
Purchase Order No:
MIFAB reserves the right to make changes in material and design without formal notice or obligation.
Page CR53
USA: 1-800-465-2736 www.mifab.com CAN: 1-800-387-3880
2013-06-26