®
AS3(AS3B/AS3S) Three Tier Component
Shelf Mount
Product Overview:
The AS3 is a three shelf cable management system. The AS3 has a sleek design which can be
used with or without a Plasma/LCD mount. The wall mount is constructed from two high grade
molded aluminum wall plates and two 5/16" thick glass shelves capable of holding up to 105
LBS each. The shelving unit is designed to fit under your display and provide an on wall solution
for all components such as cable boxes, DVD players, game consoles, and stereo components.
There are three 3 3/16” holes on the aluminum plate that allow you to neatly run your cables
up to your TV or down to another component, as well as out the bottom to an outlet.
Key Features:
● Max Weight of 105 LBS
● Built-in Cable Management
● High Grade Aluminum And Heavy Duty Tempered Glass Design
● Drywall, Concrete or Wood Stud Installation
● Single Stud Installation
● All Installation Hardware Included
Specifications:
Model:
AS2 (AS2B/AS2S)
Wall Plate Dimensions:
7.5 x 2.5"
Glass Shelf Dimensions:
17.62 x 14.12 x 5/16"
Cable Management:
Two 3 3/16" Holes
Unit Materials:
Wall Plates: Aluminum
Shelves: Tempered Glass
Shelf Spacing:
8.75"
Mounting Hole Pattern:
5.5x7.5"
Max Weight:
105 LBS
Installation Options:
Drywall , Wood Stud or
Concrete.
Assembled Dimensions :
29x 14.12 x 17.62"
(Height x Depth x Width)
Parts List:
Installation Instructions:
Preparing for assembly: Remove all items from the box and inspect all parts of the unit. Remove the
plastic film from the glass shelves. Applying heat with a blow dryer or heat gun to the film helps remove
it from the glass.
Assembling the shelving unit:
1. Assemble the parts one at a time in the order
shown.
2. The metal end plates (6) have a top and a
bottom. Attach them so that the recessed screw
holes in the center are facing outward.
3. When installing the protective plastic plates (5)
make sure the flat side is towards the glass.
4. The rod (8) guides on the protective plates (5)
fit into the aluminum sections (2,3,4). It is a very
tight fit but once in place, it adds to the stability of
the shelving unit.
5. Once fully assembled you can use the two
included Allen wrenches(9) to tighten the top and
bottom rod screws (7) at the same time.
Once assembly is complete your shelving unit
should look like as shown.
Pre-Drill Mounting Holes: Once you have determined where you would like to install your shelving unit
you will need to pre-drill the holes for the wall plate. Please refer to the following table to determine the
size of the pre-drilled hole and depth.
Installation Option:
Pre-Drill:
Wood Stud
1/8" drill bit x 2" deep
Drywall
5/8" drill bit x drywall depth
Concrete
1/2" drill bit x 2" deep
Note on Concrete Installation: For concrete installation it is required to use the plastic concrete anchors
to provide maximum support for your installation. When drilling into concrete or masonry, you have to
use a special masonry drill bit which you can purchase at your local hardware store. Using a standard
drill bit will not penetrate the concrete and it will just dull your drill bit. It is not recommended to drill
and mount into concrete block or mortar joints. If mounting into concrete or masonry we recommend
using all of the supplied plastic anchors and lag bolts for maximum support. The supplied plastic anchors
are rated for use up to 55LBS, but if you prefer you can go to your local hardware store and purchase
metal concrete anchors.
Installing the wall plate: To install your wall plate
to the wall please refer to the following figures:
1. For wood stud installation see figure 3A.
2. For drywall installation see figure 3B.
3. For concrete installation see figure 3C.
Toggle Bolt Note: You must screw on the toggle bolt head before running the toggle into the wall.
Note On Running Cables: You may find it easier to run some or all of your cables before attaching the
shelving unit to the wall plate.
Installing the shelving unit to the wall plate: Once the
wall plate is installed and secure you can now install
the shelving unit to the wall. To install the shelving unit
to the wall simply take the shelving unit and set it onto
the top of the wall plate. Next, screw in the two screws
through the top of the shelving unit into the wall plate.
Once both screws are inserted and tight, your
installation is complete.
ATTENTION:
This mount must be installed using the supplied hardware with both lag bolts screwed into your stud, all
four toggle bolts used in the drywall, or all four anchors used in the concrete or mortar for maximum
support. If you are concerned about the stability of your installation please test before mounting
expensive equipment. Cheetah Mounts™ cannot be held liable for damage to Walls, TV's, Furniture, or
Fixtures after installing this item. The limited warranty extends to the product only.
© 2009 Cheetah Mounts ™
Revision: 2.4.7
Revision Date: 10/10