C2
| alure 2
project
type
quantity
Optics
under stack
blade baffle
T5
LED
2.25
2.25
2.06
baffle
white acrilic diffuser
aperture
1252
Lumen Guide
Output
Nominal
wattage
Efficacy
847 lm/ft
9.5 W/ft
89 lm/W
939
626
313
Available Light Platforms
LED
T5
1
controls
friendly
Available Mounting
ceiling
mount
1
under
stack
mount
w w w.al i ghts .c om
integrations
C2
| alure 2
integrations
Linear Dimensions:
C2 is only available as "integrations" due to the custom
nature of stack mounting. All lengths should be specified as
follows...
Nominal Row
R___: Specify in nominal feet.
Choose when nominal length is acceptable.
Actual length will be shorter or longer due to metric lamp
lengths. Lengths over 12' are comprised of multiple sections.
Examples: a nominal 54ft row begins as C2R54; a 7ft
individual as C2R7.
Exact Row
M___: Specify overall length in inches to the nearest
hundredth.
Choose when exact lengths are required as determined by
space constraints, etc.
Submittals required. Lengths over 12' are comprised of
multiple sections.
Examples: an exact 54ft row begins as C2M648.00; a 7ft
individual as C2M84.00.
Output / Lamping:
LED. 5yr warranty. >60,000hr LED life. Tested to LM-79
and LM-80. See wattage/lumen table for specifications per
foot. All specifications are subject to change.
T5/T5HO. Single lamp in cross section. Low-profile
electronic, high power factor, program start, sound rating A,
inherent thermal protection, UL listed Class P, <10% THD.
Dimming: specify manufacturer/model.
Mounting:
Surface/Ceiling Mount. Fixture mounts directly to ceiling
via preattached mounting plate. Power connects inside
fixture using BX or MX style wiring. To install, detach
mounting plate via thumbscrews inside fixture. Affix plate
to ceiling via pre-drilled holes or by drilling through plate.
Power knockout is located in center of mounting plate.
Reattach fixture to mounting plate via thumbscrews.
Stack Top Mount. Steel prepainted mounting plate
(provided) bolts to stack top by drilling through plate
anywhere attachment is needed. Fixture then bolts to
mounting plate. Factory assumes J-Box is in the floor at the
beginning of each row of stacks/frames or “range”. Power
runs up through the unistrut channel located in the center
of the range and into the inside of the upper shelf. Connect
power inside the stack within the first shelf in the back.
Power location must be specified via the submittal process.
Factory requires stack drawings.
Driver:
Constant Current LED Systems:
Inherent dimming
Power Factor > 90%
90°C case rating
Inherent short-circuit protection
<20% total harmonic distortion
Extreme low-temperature performance to -40°C
Sound rating A
UL/CSA Listed Class 2 rating
IP66 rated
Universal 120-277V
Output:
LS_ _: LED standard output 600 lm/ft
5 watts/ft
LH_ _: LED high output
1200 lm/ft 10 watts/ft
Color Temp:
85CRI is standard; 90+ is available upon request.
Insert a 2-digit number for color temp after the LED
nomenclature.
30 = 3000 K
35 = 3500 K
40 = 4000 K
Consult factory for special order color temperatures.
LED Optics:
WISP™ lens is the factory standard recommendation
for use with LED. Available options are dependent
upon a particular luminaire.
Consult factory prior to specification.
T5/T5HO:
Single or dual lamps in cross section. Program start is factory
standard.
Finish:
Electrostatically applied powder coat finish.
Construction:
60% recycled aluminum extruded housing. Precision milled
endcaps.
Listing:
UL/CUL. Damp Location.
Companion Luminaires:
A1 suspended/ceiling, A4 wall, C3 table mount, C4 stack
NOTE: When stack top mounting, take into consideration
clearance for books. Allow for an additional 3” top height to
accommodate books.
LED:
5yr warranty. >60,000hr LED life. Tested to LM-79 and
LM-80. See wattage/lumen table for specifications per
foot. All specifications are subject to change. Built with
high-performance Nichia® LED’s. Heat sync designed to
ensure proper performance. LED boards are replaceable,
built in foot-long increments. Board position/quantity to be
determined by factory.
a·light
w w w.al i ghts .c om
2
C2
| alure 2
LED
project
Series:
type
quantity
C2
Dimension:
C2 is only available as "integrations" due to the modifications required for stack mounting
Damp location nominal length
Exact length
R___
M___
Output:
LED standard output
LED high output
LS
LH
3000k
3500k
4000k
30
35
40
Specify length in feet.
Specify length in inches to the nearest 100th.
LED Temp (if applicable):
Voltage:
Universal 120V - 277V
120V
277V
347V
U
1
2
3
WISP™ lens
S
Downlight Optics:
Mounting:
Surface / Ceiling mount
a∙lightanium™
Satin white
Satin black
Textured eggshell white
Other
Custom
F
Finish:
T
W
B
E
O
C
Specify RAL#
Options:
3
Dimming
D
Emergency
E
External fusing
F
Multi-circuit
M
New York City code
N
Occupancy sensor
O
Photocell / Daylight sensor
P
Right endcap feed
Left endcap feed
R
L
Specify manufacturer, model/series and voltage.
Emergency ballast not applicable on lengths 3ft
or less.
Specify model/series or lumens.
Multi-circuiting: submit multi-circuiting
requirements during submittal process.
Standard on/off occupancy sensor: Wattstopper
FS-205 with minimal 1” diameter.
Standard fixture-integrated dimmimg
photosensor: Wattstopper FD-301 wired for
daylight harvesting. Requires 0-10V dimming
ballast.
w w w.al i ghts .c om
Version | November 2015
integrations
C2
| alure 2
T5
T8
project
Series:
type
quantity
C2
Dimension:
C2 is only available as "integrations" due to the modifications required for stack mounting
Damp location nominal length
R___
Specify length in feet.
Exact length
M___
Specify length in inches to the nearest 100th.
Lamping:
T5 (1)
T5HO (1)
S
H
Universal 120V - 277V
120V
277V
347V
U
1
2
3
WISP™ lens
S
Voltage:
Downlight Optics:
Mounting:
Surface / Ceiling mount
a∙lightanium™
Satin white
Satin black
Textured eggshell white
Other
Custom
F
Finish:
T
W
B
E
O
C
Specify RAL#
Options:
a·light
Dimming
D
Specify manufacturer, model/series and voltage.
Emergency
E
External fusing
F
Emergency ballast not applicable on lengths 3ft
or less.
Specify model/series or lumens.
Multi-circuit
M
New York City code
N
Occupancy sensor
O
Photocell / Daylight sensor
P
Right endcap feed
Left endcap feed
R
L
Multi-circuiting: submit multi-circuiting
requirements during submittal process.
Standard on/off occupancy sensor: Wattstopper
FS-205 with minimal 1” diameter.
Standard fixture-integrated dimmimg
photosensor: Wattstopper FD-301 wired for
daylight harvesting. Requires 0-10V dimming
ballast.
w w w.al i ghts .c om
4