f
i
c
a
t
i
Leg Brace Mechanism
Leg braces shall be constructed of at least 7/8” wide x .125” thick, edge-radiused steel. Braces made of less than
11 gauge steel are not acceptable. For safety, braces shall lock automatically and remain locked when the table is
in any position during folding and unfolding. Braces shall be designed and constructed to resist wear from frequent
operation that could prevent the brace from locking the leg securely in place. Spring actuated devices with casehardened steel poppits are preferred. The leg brace pivot bracket shall be secured to the table top using a minimum
of eight fasteners.
i
Leg Assembly
All leg assemblies shall be wishbone style having vertical load bearing members of at least 1-1/16” diameter, 14
gauge, steel tubing. The upper, horizontal tube on leg assemblies shall rotate within two, 16 gauge steel saddle
clips. Saddle clips shall be fastened to the table top using a minimum of four screws each. Leg assemblies are to
be capped at the bottom with load bearing, high impact, plastic glides, secured with spring steel internal grippers.
No horizontal members shall be positioned less than 12” from the floor to facilitate floor cleaning. For stability, no
wishbone style leg assembly shall have an offset in the leg greater than five inches. Specialty shaped tables and
round tables 36” or less in diameter are furnished with independent folding legs of 1-1/16” diameter, 14 gauge steel
tubing or a combination of independent and wishbone legs. Comfort Leg assemblies shall be constructed of 1¼”
diameter steel tubing and shall provide a minimum of 9“of free knee space on 18” wide tables.
c
Top Support Structure
Two hardwood supports, measuring 1” x 1¾”, shall be secured to the top with
bolts running through the top and counter-sunk into the wood supports. Bolt
heads shall have heads that fit flush with the top.
e
Top
Tops shall be constructed of solid, ¾” thick, AC grade, 7 ply, exterior glue plywood. The top surface is to be finished with a walnut sealer stain. Edges are
to be protected by an 18 gauge, galvanized steel angle that shall be secured
with screws from the underside of the table top and placed at intervals not to
exceed 10”. Edging must fit flush with the table top.
p
E Series Folding Tables
s
Revised: 6/8/2009
Metal Finish
All metal parts shall be thoroughly cleaned and phosphatized to enhance paint adhesion. Metal parts are to be
finished with a thermofused epoxy powdercoating.
o
Warranty
E Series Folding Tables shall be covered by a 10-year warranty.
n
s
i
f
i
Top Support Frame
Table tops shall be supported by a 16 gauge formed steel channel frame at least 1-13/16” deep. The channel shall
form a continuous frame having square corners and welded joints. Frames shall be secured to the table top with
screws placed no greater than 10” apart.
c
Optional PermaTuff Edge: Tops shall be constructed of solid, ¾” thick, AC
grade, exterior glue plywood, surfaced with high pressure plastic laminate and
are to be backed with a phenolic sheet to prevent moisture penetration. Edges
of tops shall be protected with a polyurethane epoxy resin, chemically bonded
to the edges of the plastic laminate, core material and backing sheet.
e
Top
Tops shall be constructed of solid, 3/4” thick, AC grade, 7 ply, exterior glue plywood, surfaced with high pressure plastic laminate and are to be backed with a
phenolic sheet to prevent moisture penetration. Tops are to be edged with vinyl
T molding having a thickness of at least 3/16”. The T molding shall be secured
against removal by the use of staples at regular intervals on the under side of
the table top.
p
EF Series Folding Tables
s
Revised: 6/8/2009
c
n
s
o
Warranty
EF Series Folding Tables shall be covered by a 10-year warranty.
i
Metal Finish
All metal parts shall be thoroughly cleaned and phosphatized to enhance paint adhesion. Metal parts are to be
finished with a thermofused epoxy powdercoating.
t
Leg Brace Mechanisms
Leg braces shall be constructed of at least 7/8” wide x .125” thick, edge-radiused steel. Braces made of less than
11 gauge steel are not acceptable. For safety, braces shall lock automatically and remain locked when the table is
in any position during folding and unfolding. Braces shall be designed and constructed to resist wear from frequent
operation that could prevent the brace from locking the leg securely in place. Spring actuated devices with casehardened steel poppits are preferred. The leg brace pivot bracket shall be secured to the table top using a minimum
of eight fasteners.
a
Leg Assemblies
All leg assemblies shall be wishbone style having vertical load bearing members of at least 1-1/16” diameter, 14
gauge, steel tubing. The upper, horizontal tube on leg assemblies shall rotate within two, 16 gauge steel saddle
clips. Saddle clips shall be fastened to the table top using a minimum of four screws each. Leg assemblies are to
be capped at the bottom with load bearing, high impact, plastic glides, secured with spring steel internal grippers.
No horizontal members shall be positioned less than 12” from the floor to facilitate floor cleaning. For stability, no
wishbone style leg assembly shall have an offset in the leg greater than five inches. Game tables and round tables
36” or less in diameter are furnished with four independent folding legs of 1-1/16” diameter, 14 gauge steel tubing.
Comfort Leg assemblies shall be constructed of 1¼” diameter steel tubing and shall provide a minimum of 9“of free
knee space on 18” wide tables.
f
i
c
a
t
i
Leg Brace Mechanism
Leg braces shall be constructed of at least 7/8” wide x .125” thick, edge-radiused steel. Braces made of less than
11 gauge steel are not acceptable. For safety, braces shall lock automatically and remain locked when the table is
in any position during folding and unfolding. Braces shall be designed and constructed to resist wear from frequent
operation that could prevent the brace from locking the leg securely in place. Spring actuated devices with casehardened steel poppits are preferred. The leg brace pivot bracket shall be secured to the table top using a minimum
of eight fasteners.
i
Leg Assembly
All leg assemblies shall be wishbone style having vertical load bearing members of at least 1-1/16” diameter, 14
gauge, steel tubing. The upper, horizontal tube on leg assemblies shall rotate within two, 16 gauge steel saddle
clips. Saddle clips shall be fastened to the table top using a minimum of four screws each. Leg assemblies are to
be capped at the bottom with load bearing, high impact, plastic glides, secured with spring steel internal grippers.
No horizontal members shall be positioned less than 12” from the floor to facilitate floor cleaning. For stability, no
wishbone style leg assembly shall have an offset in the leg greater than five inches. Specialty shaped tables and
round tables 36” or less in diameter are furnished with independent folding legs of 1-1/16” diameter, 14 gauge steel
tubing or a combination of independent and wishbone legs. Comfort Leg assemblies shall be constructed of 1¼”
diameter steel tubing and shall provide a minimum of 9“of free knee space on 18” wide tables.
c
Top Support Structure
Two hardwood supports, measuring 1” x 1¾”, shall be secured to the top with
bolts running through the top and counter-sunk into the wood supports. Bolt
heads shall have heads that fit flush with the top.
e
Top
Tops shall be constructed of solid, ¾” thick, AC grade, 7 ply, exterior glue
plywood that is padded. Padded tops shall be laminated with a 1/16” thick,
white vinyl material. Edges are to be protected by an 18 gauge, galvanized
steel angle that shall be secured with screws from the underside of the table
top and placed at intervals not to exceed 10”. Edging must fit flush with the
table top.
p
EP Series Folding Tables
s
Revised: 6/8/2009
Metal Finish
All metal parts shall be thoroughly cleaned and phosphatized to enhance paint adhesion. Metal parts are to be
finished with a thermofused epoxy powdercoating.
o
Warranty
E Series Folding Tables shall be covered by a 10-year warranty.
n
s
i
f
i
Leg Assemblies
All leg assemblies shall be constructed with 1 1/4” square, 18 gauge steel tubing.
Legs shall hinge directly on the tubular steel top support frame and are to be
capped at the bottom with adjustable leveling glides. Plastic bumpers are riveted to the upper portion of each to
allow stacking without damage to tabletops.
c
Top Support Structure
A frame constructed of 1 1/4” square, 18 gauge steel tubing shall be bolted to the
tabletop. Bolt heads shall have heads that fit flush with the top.
e
Top
Tops shall be constructed of solid, ¾” thick, AC grade, 7 ply, exterior glue plywood. The top surface is to be finished with a moisture resistant sealer. Edges
are to be protected by a channel shaped aluminum molding, secured on the
underside at regular intervals with mechanical fasteners.
p
ES Series Folding Tables
s
Revised: 6/8/2009
Leg Brace Mechanism
Leg braces shall pivot directly on the leg assemblies and on the tubular steel frame. Braces are secured in the
opened position by coil springs to prevent accidental closing.
c
Metal Finish
All metal parts shall be thoroughly cleaned and phosphatized to enhance paint adhesion. Metal parts are to be
finished with a thermofused epoxy powdercoating.
a
Warranty
ES Series Folding Tables shall be covered by a 3-year warranty.
t
i
o
n
s
t
i
o
n
s
a
Warranty
ET and EV Series Folding Tables shall be covered by a 1-year warranty
c
Metal Finish
All metal parts shall be thoroughly cleaned and phosphatized to enhance paint adhesion. Metal parts are to be
finished with thermofused epoxy powdercoating.
i
Leg Brace Mechanisms
Leg braces shall be constructed of at least 7/8” wide x .125” thick, edge-radiused steel. Braces made of less than
11 gauge steel are not acceptable. For safety, braces shall lock automatically and remain locked when the table is
in any position during folding and unfolding. Braces shall be designed and constructed to resist wear from frequent
operation that could prevent the brace from locking the leg securely in place. Spring actuated devices with casehardened steel poppits are preferred. The leg brace pivot bracket shall be secured to the table top using a minimum
of eight fasteners.
f
Leg Assemblies
All leg assemblies shall be wishbone style having vertical load bearing members of 1” diameter, 16 gauge, steel tubing. The upper, horizontal tube on leg assemblies shall rotate within two, 16
gauge steel saddle clips. Saddle clips shall be fastened to the table top using a minimum of four screws each. Leg
assemblies are to be capped at the bottom with load bearing, high impact, plastic glides, secured with spring steel
internal grippers. No horizontal members shall be positioned less than 12” from the floor to facilitate floor cleaning. For stability, no wishbone style leg assembly shall have an offset in the leg greater than five inches. Specialty
shaped tables and round tables 36” or less in diameter are furnished with independent folding legs of 1” diameter, 16
gauge steel tubing or a combination of independent and wishbone legs.
i
Top Support Structure
Two hardwood supports, measuring 1 ¼” x 1 ½”, shall be secured to the top
with flush fitting, flathead wood screws.
c
Top (EV Series)
Tops shall be constructed of solid, ¾” thick, AC grade, 7 ply, exterior glue
plywood. The top surface is to be finished with a walnut sealer stain to resist
moisture. Edges are to be protected by a vinyl bullnose T molding and shall
be secured with brads from the underside of the table on intervals not to
exceed 12”. Edging must fit flush with the table top.
e
Top (ET Series)
Tops shall be constructed of solid, ¾” thick, AC grade, 7 ply, exterior glue
plywood. The top surface is to be finished with a walnut sealer stain to resist
moisture. Edges are to be protected by an extruded aluminum T molding and
shall be secured with brads from the underside of the table top at all joints.
Edging must fit flush with the table top.
p
ET & EV Series Folding Tables
s
Revised: 6/8/2009
c
a
t
i
o
n
Warranty
F Series Folding Tables shall be covered by a 1-year warranty.
i
Metal Finish
All metal parts shall be thoroughly cleaned and phosphatized to enhance paint adhesion. Metal parts are to be
finished with a thermofused epoxy powdercoating.
f
Leg Brace Mechanisms
Leg braces shall be constructed of at least 7/8” wide x .125” thick, edge-radiused steel. Braces made of less than
11 gauge steel are not acceptable. For safety, braces shall lock automatically and remain locked when the table is
in any position during folding and unfolding. Braces shall be designed and constructed to resist wear from frequent
operation that could prevent the brace from locking the leg securely in place. Spring actuated devices with casehardened steel poppits are preferred. The leg brace pivot bracket shall be secured to the table top using a minimum
of eight fasteners.
i
Leg Assemblies
Leg assemblies on rectangular tables more than 24” wideshall be shall be pedestal style. The U shaped pedestal
base shall be constructed of at least 1 1/16” diameter, 14 gauge steel tubing. Pedestal legs shall have a full width
horizontal tube welded to two vertical members. Leg assemblies on 18” and 24” wide tables shall be wishbone style
with vertical load bearing members of at least 1-1/16” diameter, 14 gauge, steel tubing. Game tables and round
tables 36” or less in diameter are furnished with four independent folding legs of 1-1/16” diameter, 14 gauge steel
tubing. The upper, horizontal tube on all leg assemblies shall rotate within two, 16 gauge steel saddle clips. Saddle
clips shall be fastened to the table top using a minimum of four screws each. Leg assemblies are to be capped at
the bottom with load bearing, high impact, plastic glides, secured with spring steel internal grippers.
c
Top Support Frame
Table tops shall be supported by a 16 gauge formed steel channel frame
at least 1-13/16” deep. The channel shall form a continuous frame having
square corners and welded joints. Frames shall be secured to the table top
with screws placed no greater than 10” apart.
e
Top
Tops shall be constructed of solid, 47 lb., industrial grade particleboard, surfaced with high pressure plastic laminate and shall be backed with a phenolic
sheet to prevent moisture penetration. Tops are to be edged with vinyl T
molding having a thickness of at least 1/8”.
p
F Series Folding Tables
s
Revised: 6/8/2009
s
a
t
i
o
n
s
c
Warranty
Hexalite™ Series Folding Tables shall be covered by a 15-year warranty
i
Metal Finish
All metal parts shall be thoroughly cleaned and phosphatized to enhance paint adhesion. Metal parts shall be then
finished with a thermofused epoxy powdercoating.
f
Leg and Brace Attachment
Legs and leg braces shall be anchored securely to 18 gauge steel anchor plates that are epoxy bonded to the polypropylene honeycomb core and the ABS bottom sheet, with a minimum of 32 sheet metal fasteners.
i
Leg Brace Mechanisms
Leg braces shall be constructed of at least 7/8” wide x .125” thick, edge-radiused steel. Braces made of less than
11 gauge steel are not acceptable. For safety, braces shall lock automatically and remain locked when the table is
in any position during folding and unfolding. Braces shall be designed and constructed to resist wear from frequent
operation that could prevent the brace from locking the leg securely in place. Spring actuated devices with casehardened steel poppits are preferred. The leg brace pivot bracket shall be secured to the table top using a minimum
of eight fasteners.
c
Leg Assemblies
All leg assemblies shall be wishbone style having vertical load bearing members of at least 1” diameter, 16 gauge,
steel tubing. The upper, horizontal tube on leg assemblies shall rotate within two, 16 gauge steel saddle clips. Saddle clips shall be fastened to the table top using a minimum of four screws each. Leg assemblies are to be capped
at the bottom with load bearing, high impact, plastic glides, secured with spring steel internal grippers. No horizontal
members shall be positioned less than 12” from the floor to facilitate floor cleaning. For stability, no wishbone style
leg assembly shall have an offset in the leg greater than five inches. Game tables and round tables 36” or less in
diameter are furnished with four independent folding legs of 1-1/16” diameter, 14 gauge steel tubing. Comfort Leg
assemblies shall be constructed of 1¼” diameter steel tubing and shall provide a minimum of 9“of free knee space
on 18” wide tables.
e
Top
Tops shall be constructed of an aircraft grade, honeycomb structural core of
polypropylene plastic. Cells within the core shall not exceed ¼” spacing to
ensure uniform support to the top surface. The exterior surfaces of the table
shall be constructed of thermoformed, ABS plastic material, permanently
bonded to the honeycomb core with epoxy adhesive. Edges of the table top
are protected against impact with a profile extrusion of high-impact, PVC plastic molding that interlocks with and is permanently bonded to the ABS exterior
of the table with epoxy adhesive. The molding shall incorporate a 5/32” thick
bumper edge, backed by a tubular shaped, impact-absorbing reinforcement.
There shall be no less than five layers of plastic to protect the edges of the table top. Corners of rectangular models
are protected with rib reinforced, injection molded, PVC plastic sections that interlock with the edge molding.
No wood products shall be used in the construction of table tops.
p
Hexalite™ Series Folding Tables
s
Revised: 6/8/2009
s
Revised: 6/8/2009
p
Top and Frame
Tops shall be constructed of solid, 3/8” thick, three ply, AC grade,
exterior glue plywood protected with a sealer stain. Top edges are to
be protected by a 16 gauge, formed steel angle at each end. A frame,
consisting of a 16 gauge, steel U channel, 1” wide x 1-1/8” high, must
incorporate a protective edging for the plywood as an integral part of
the table frame. The frame is to be securely riveted to the plywood
top with flat head rivets to provide support for the top and a smooth
runner, which facilitate stacking of folded tables.
e
a
t
i
o
n
s
c
Warranty
RP Series Folding Tables shall be covered by a 10-year warranty.
i
Metal Finish
All metal parts shall be thoroughly cleaned and phosphatized to enhance paint adhesion. Metal parts are to be
finished with a thermofused epoxy powdercoating.
f
Leg Brace Mechanisms
Leg braces shall be constructed of at least 7/8” wide x .125” thick, edge-radiused steel. Braces made of less than
11 gauge steel are not acceptable. For safety, braces shall lock automatically and remain locked when the table is
in any position during folding and unfolding. Braces shall be designed and constructed to resist wear from frequent
operation that could prevent the brace from locking the leg securely in place. Spring actuated devices with casehardened steel poppits are preferred. The leg brace pivot bracket shall be secured to the table top using a minimum
of eight rivets.
i
Leg Assemblies
All leg assemblies shall be wishbone style having vertical load bearing members of at least 1-1/16” diameter, 14
gauge, steel tubing. The upper, horizontal tube on leg assemblies shall rotate within two, 16 gauge steel saddle
clips. Saddle clips shall be fastened to the table top using a minimum of four screws each. Leg assemblies are to
be capped at the bottom with load bearing, high impact, plastic glides, secured with spring steel internal grippers.
No horizontal members shall be positioned less than 12” from the floor to facilitate floor cleaning. For stability, no
wishbone style leg assembly shall have an offset in the leg greater than five inches. Game tables and round tables
36” or less in diameter are furnished with four independent folding legs of 1-1/16” diameter, 14 gauge steel tubing.
Comfort Leg assemblies shall be constructed of 1¼” diameter steel tubing and shall provide a minimum of 9“of free
knee space on 18” wide tables.
c
RP Series Folding Tables