CHAIN SAW ACCESSORIES - O.E.M
UNIVERSAL
Part#
UNIVERSAL
O.E.M
Application
Part#
Banta
continued
O.E.M
Application
440-034
135-004
New Style Single
Terminal Electronic
Ignition Module
This module comes in
a metal case. Complete with instruction sheet,
and fasteners. For use on Chain Saws, Brush Cutters,
String-Trimmers and Hedge Trimmers that have had
mechanical points originally.
7mm Spark Plug Wire.
Quality black hypolon outer
case with COPPER
(not carbon) inner wire.
For use on most Small engine / 4 stroke Lawn &
Garden applications. (7mm wire OD X 20 FT roll).
For Carburetor Kits and Parts
please see our sections “10”, “11” &“12”
TYGON FUEL LINE
115-300
Size: 3/32” ID X 3/16” OD (50 FT roll)
115-305
Size: 1/8” ID X 3/16” OD (50 FT roll)
430-017
115-310
Toggle Kill Switch
Used as an on / off switch.
Found on many Chain saws and
Trimmers using a single wire, self grounding
type switch. Kill Switch found on many small chain saw
and trimmer models with spade terminal wire end.
Size: 1/8” ID X 1/4” OD (50 FT roll)
Special formulation vinyl and oil tubing for
Chain saws, Snowmobiles and Lawnmowers. Maintains
an air tight seal on fittings even in extreme temperatures.
Resists swelling or hardening. Translucent material allows
visual inspection of flow. Temperature range 35 degrees
below to 165 degrees F.
135-053
For more sizes and information on Tygon Fuel Lines
see our “FUEL LINE and ACCESSORIES” section
Spark Plug Boot
For many Chain Saws & Trimmers.
(Fits 5mm spark plug wire)
115-106
(Sold in multiples of 10)
135-095
Spark Plug Boot
For Lawn and Garden equipment.
(Fits 7mm spark plug wire)
(Sold in multiples of 10)
135-046
Spark Plug Boot
Found on Lawn and
Garden equipment.
(Fits 7mm spark plug wire.)
(Sold in multiples of 10)
135-015
5mm Spark Plug Wire
Quality black hypolon outer case
with COPPER (not carbon)
inner wire. Used on many chain
saw and trimmer application.
(5mm wire OD X 10 meter roll).
C
G
Fuel Filter - In Tank
Use with 1/8” ID fuel line.
(felt material).
Found on many older Homelite chain saws.
Measures: 1-1/2” Long X 9/16” diameter.
(Sold in multiples of 10)
Replacement felt for above
Measures: 1” Long X 1/4” ID
X 9/16” OD.
135-012
135-061
For additional fuel parts see our
“FUEL LINE & ACCESSORIES” section 26
610-014
610-022
Spark Plug Clip
Universal application. Used in our
135-053 & 135-095 spark plug boots.
Spark Plug Clip
Universal application. Used in
our 135-046 spark plug boots
NEOPRENE FUEL LINE
(5 meter roll = 16.5 FT
approx). Neoprene fuel
line is oil and gas resistant.
Size: 1/8” ID X 9/32” OD.
For many Chain Saw and Trimmer applications.
(Sold in multiples of 10)
610-006
(Sold in multiples of 10)
Fuel Filter - In Tank
Use with 1/8” ID fuel line.
(felt material).
Found on many chain saws.
Measures: 1-1/2” Long X 13/16” diameter.
610-030
Replacement felt for above
Measures: 1” Long X 7/16” ID
X 13/16” OD.
16-01
(Sold in multiples of 10)
G
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
UNIVERSAL
Part#
UNIVERSAL
continued
O.E.M
Application
614-527
Fuel Filter - In Tank
Use with 1/8” ID fuel line.
Dual filtration felt and stainless
steel mesh element.
Used on engines up to 33cc.
Part#
continued
O.E.M
Application
415-623
(Sold in multiples of 5)
614-528
Fuel Filter - In Tank
Use with 1/8” ID fuel line.
Dual filtration felt and stainless
steel mesh element.
Used on engines up to 80cc.
(Sold in multiples of 5)
613-601
Intake Gasket
Assortment
This assortment
contains carburetor
mount gaskets for
Tillotson, TK, Nikki,
Walbro and Zama
carburetors. Gasket
comes in a plastic
container that is labeled for easy reordering. Includes
117 pieces in total. (Note: Individual gasket sold in packs
of 10) See our “CARBURETOR KITS” section for more
information and better carburetor mount gasket pictures.
For other Chain saw related gaskets - See our “CHAIN
SAW ACCESSORIES - O.E.M.” section that follows
this one. Done in alphabetical order by Chain Saw
Manufacturers name A thru Z
Fuel Filter - In Tank
Use with 3/32” thru 1/8” ID fuel lines.
Our most popular filter for
small trimmers and chain saws.
560-101
Measures: 1-1/4” long X 1/2” diameter.
Starter Dog / Starter Pawl
(Large)
Found on many older chain saws
using an aluminum starter cup.
Size: Dog width: 1/2” with a 3/8” ID.
613-602
Fuel Filter - In Tank
Use with 1/8” ID fuel line.
Measures: 1-1/4” long X 1/2” diameter.
560-102
613-603
Measures: 1-5/8” long X 11/16” diameter.
Starter Dog Washer
This is a fibre washer used on
older Fairbanks Morse,
Remington etc. chain saws that
used a starter dog assembly and
aluminum starter cup.
613-604
140-061
Fuel Filter - In Tank
Use with 1/8” ID fuel line.
Measures: 1-5/8” long X 11/16” diameter.
Starter Handle
Universal rubber handle
with steel insert. For use with
#4 thru #6 Starter Rope sizes.
Fuel Filter - In Tank
Use with 3/32” or 1/8” ID fuel line.
Fits Husqvarna chain saws and many others.
613-605
(Sold in multiples of 10)
(Sold in multiples of 10)
560-123
Fuel Filter - In Tank
Use with molded fuel lines. (1/4” ID)
Fits chain saw models with molded fuel lines.
Measures: 11/16” OD X 1-5/8” overall length.
Starter Handle
Universal heavy duty Starter
Handle. This large plastic
handle has a removable
cap for putting rope knot.
613-607
147-045
Fuel Filter - In Tank
For use with molded fuel lines.
Starter Rope #4-1/2
Premium 16 carrier smooth
braid starter rope / starter cord.
Red tracer. Smoother cycling.
Flexibility increased while maintaining
firmness. Wound on a plastic spool. (Made in Germany).
(3.6mm or 9/64” diameter) X 100 FT.
Fits Stihl chain saw models: 034,
036, 038 etc with molded fuel lines.
NOTE: Similar to our our 613-605 but larger diameter (23mm).
Recommended for larger cc Stihl chain saws.
044, MS440, 046, MS460, 064, MS640, 066, MS660 etc.
Measures:1-3/4” overall length X 23mm diameter.
C
16-02
For more starter rope sizes see our
“STARTER PARTS” section 42
C
CHAIN SAW ACCESSORIES - O.E.M
UNIVERSAL
Part#
DOLMAR / MAKITA
continued
Part#
O.E.M
775-080
605-362
395 173 090
Shop Repair Tags
Individually numbered
with customer tear-off.
Pre Cleaner
Fits Makita / Sachs Dolmar
models: PC6412, PC6414,
PC6530, PC6535, PC7312,
PC7314, PC7430, PC7435,
PC8116 and PC8240
Size: 6-3/8” L X 5-3/8” W X 11/16” HT
O.E.M
Application
(Sold in multiples of 50)
DOLMAR / MAKITA
605-003
605-350
122 173 030
Air Filter
Fits Chain Saws model:122
Size: 3-3/8” L X 3-3/8” W X 1/2” HT
605-005
114 173 531
Air Filter
Fits Chain Saws models: 113 and 116.
Size: 4” L X 2-1/4” W X 7/16” HT
605-006
(While Quantities Last)
123 173 110
123 173 120
Air Filter
Fits Chain Saws model: 123
Size: 3-5/8” L X 3-1/2” W X 3/4” HT
605-355
394 173 010
Wacker# 0108076
Wacker# 0108077
Banta
cont.
Application
395-173-010
Air Filter
Fits Concrete Saws models:
Dolmar: PC6412, PC6414,
PC6530, PC6535, PC7312.
PC7314, PC7430, PC7435,
PC8116 and PC8240. Makita: DPC6430, DPC6431,
DPC6440, DPC6441, DPC7330,DPC7331, DPC7340,
DPC7341, DPC8131 and DPC8132 Wacker: BTS 930 L3,
BTS 935 L3, BTS 1030 L3, BTS 1035L3 and BTS 1140 L3.
Size: 4-1/8” L X 3-5/16” W X 1-7/8” HT.
(NOTE: Similar to our 605-355 but measures 1-7/8” high vs our
605-355 at 2-5/16” high).
605-356
394-173-020
Air Filter
Fits Makita / Dolmar / Sachs
Concrete Saws. Models: DPC6200,
6201, 6410, 6411, 7300, 7301, 7310 and 7311.
Size: 3-11/16” L X 2-5/8” W X 1/4” HT.
(Also see our 605-355 and 605-358 filters)
Air Filter
Fits Concrete Saws models:
DPC6300, 6201, 7300C, 7301
also PC6212, PC6214, PC6412,
PC6414, PC7312, PC7314 &
PC8140. Also found on Wacker models: BTS;
Diamond Products models: SC
Size: 4-1/8” L X 3-5/16” W X 2-5/16” HT.
(Also see our 605-356 and 605-358 filters)
605-358
394 173 030
394 173 030A
670-101
Bar Nut
For Chain Saw models: 112,
114, 117, 119 (8mm hex nut)
(Sold in multiples of 10)
670-113
Bar Nut
For older chain saw models 122 & 123.
651-101
901 506 554
119 213 030
Wacker# 0108074
Pre Cleaner
For our 605-355. Fits model:
DPC6401 cut off / cut quik saw.
3 Layer filter. (Filter construction
50 PPI, 60 PPI and 80 PPI layers, bonded together).
(Also see our 605-358 and 605-355 filters).
Size: 5-1/2” L X 3-5/8” W X 3/4” HT
NOTE: Two images shown, (1) pre filter only >.
605-360
326 173 080
Pre Cleaner
For our 605-355 (Newer Style).
Fits Makita / Sachs Dolmar model: DPC811.
Size: 7-3/4” L X 5-1/8” W X 11/16” HT.
C
Chain Adjuster
For Chain Saw models
112, 114, 117 & 119.
651-106
(While Quantities Last)
901 506 554
119 213 030
(While Quantities Last)
Chain Adjuster
Fits chain saw models: CA, CC, CT,
122, 123 also found on some older 144, 152 & 153.
651-194
123 213 010
924 306 400
922 606 000
(While Quantities Last)
Chain Adjuster
For Chain Saw models 123 and 133
16-03
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
DOLMAR / MAKITA
Part#
O.E.M
570-240
123 130 000
cont.
Application
123
DOLMAR / MAKITA
Part#
O.E.M
572-481
122 132 100
cont.
Application
Piston assembly (47mm)
Fits chain saw model: 123,
also fits old concrete saw
model: 309 (old style).
Cylinder Assy (47mm)
Fits Chain saw
model: 123, also
fits old Concrete
Saw model: 309
(old style)
(While Quantities Last)
574-119
123 132 020
Piston Rings (47mm)
Fits Chain Saw model: 123,
also fits old Concrete Saw model 309.
570-258
123 130 200
309 PC
640-207
Gasket Set
Fits Concrete Saw model:
309 PC. Includes Oil Seals
Cylinder Assy (47mm)
Fits new Concrete
Saw model: 309 PC.
640-204
Gasket Set
Fits Chain Saw model:
123, 133, 133S, 143
640-206
570-239
325 130 010
325 130 030
325 130 031
325 130 033
325 130 034
325 130 035
Wacker#
0202778
0202779
0206854
DSC6200
DPC6400 & 6410
Gasket Set
Fits Chain Saw
model: 153.
640-208
Gasket Set
Fits chain saw models:
120 and 120 Si.
Includes Oil Seals
Cylinder Assy (47mm)
Fits chain saw
models: DSC6200,
DPC6400 & DPC6410.
591-101
Bearing - Piston
Fits Dolmar Chain Saw
models: 112, 114, 117 & 119.
570-001
570-246
133 130 001
962 210 015
133
Many Applications
Cylinder Plug
Fits Dolmar, Husqvarna, ICS, Makita,
Partner, Stihl and Wacker cylinder assemblies.
(For Decompression Valve see our part# 570-002)
Cylinder Assy (52mm)
Fits Chain Saw
model: 133.
C
570-002
001 131 150
Decompression Valve
For Chain Saw and Concrete
saw cylinder assemblies.
Fits many Dolmar / Makita, cylinder assemblies. Dolmar
models: 64XX, 73XX and 81XX; Makita models: DPC64XX,
DPC73XX and DPC81XX (For plug only see our 570-001).
16-04
C
CHAIN SAW ACCESSORIES - O.E.M
DOLMAR / MAKITA
Part#
O.E.M
550-156
965 451 900
ECHO
cont.
Application
Gas Cap
Fits Chain Saw models 110, 112, 113,
114, 116, 117,119, 120, 123 and 133.
551-104
965 451 230
O.E.M
605-307
130300 3973 0
605-309
108 163 010
Starter Spring
Fits chain saw
models: 103 and 108.
123 163 010
Starter Spring
119 163 010
144 163 010
605-014
Starter Spring
Fits Dolmar chain
saw models: 112, 114, 117,
119, 122, 144, 166, 308 and 310.
Wrap Handle
For Chain Saw models:
112, 114, 117,119 and 120.
670-101
(While Quantities Last)
For Chain Saw models:
C60, 452, 500, 510 and 550
A
B
T-Wrench
Fits chain saw models:
112, 113, 114, 116, 117,
119, 120 and 120 Super.
Size: A= 7”, B= 1-1/16”, C= 1”.
Bar= 1/2” (13mm), Plug= 3/4” (19mm)
C
433019
12330
Bar Nut
705-574
T-Wrench
Fits chain saw models:
CA, CC and CT
Size: A= 7”, B= 1-11/16”,
C= 1 5/8”. Bar= 11/16” (17mm),
Plug= 13/16” (21mm)
130310 03930
130310 03930 2
Air Filter
Fits Chain Saw model: 302
Size: 3-1/16” L X 2-5/8” W
112 310 010
705-525
130305 03430
Air Filter
Fits Chain Saw model:
CS-451 and CS-452
Size: 3-1/16” L X 2-3/4” W
Fits Dolmar chain saw models:
112, 133, 166, 307 and 311.
654-106
130305 0033 3
Air Filter
Fits Chain Saw model:
CS-60
Size: 4-1/4” L X 3-3/4” W
605-008
625-575
130313 3833 1
Air Filter
For Chain Saw model
CS4400 and CS510. (Tall version).
Measures: 2-1/2” OD X
1-3/4” ID X 1-3/8” HT
605-007
625-576
Application
100573
Starter Spring
For Chain Saw model “D” JR 34.
625-577
Part#
Air Filter
For Chain Saw model
CS5000 and CS5000,
Type 1E serial# 001001 and higher.
Measures: 2-1/2” OD X 1-3/4” ID X 1-1/4” HT
Oil Cap
Fits Chain Saw models:
CA and CT. (old)
625-325
Banta
651-201
(Sold in multiples of 10)
433016
13931
C
Chain Adjuster
For Chain Saw models:
280 and 290.
651-110
A
(While Quantities Last)
Echo
B
C
Chain Adjuster
For Chain Saw models:
302 and 315.
16-05
C
Banta
ECHO
CHAIN SAW ACCESSORIES - O.E.M
ECHO
continued
Part#
O.E.M
651-112
Echo
Application
Chain Adjuster
For Chain Saw model:
CS - 60.
For ECHO Clutches - See our “Trimmer
Parts” section.
175018 0022 0
621-107
Echo
Piston Ring Set
(52mm X 1.5mm)
Fits Echo chain saw model: 8000.
Aftermarket cast iron piston rings.
Two piston rings included.
551-102
436000 0393 0
Oil Cap
For Chain Saw models: 301, 351,
451, 452, 601, 602, 701 and 702.
551-103
177220 0023 0
Oil Cap
For Chain Saw model:
CS - 60S
622-498
100212 03930
Oil Seal
For (Magneto Side). Fits Chain Saw
models: 280, 302, 315, 330 and 351.
Oil Seal
For (PTO Side). Fits Chain Saw
models 302 and 351.
Measures:12mm shaftsize X 32mm OD
622-506
100212 11230
Oil Seal
For (PTO Side) Fits Chain Saw models:
280, 315, 330, 400 and 351.
Measures: 12mm shaft size X 19mm OD
C
177228 0111 0
Starter Handle
Plastic starter handle. For use on
small equipment applications.
Ideal for small trimmers, brushcutters
(Sold in multiples of 10)
and chain saw applications.
625-476
625-479
Note: Some chain saw applications use one only piston ring.
Gas Cap
For Chain Saw models:
601, 702 and 750.
140-046
Application
177220 0283 4
John Deere# MG67224
177220 0393 0
Fits chain saw models: CS-302,
CS-351, CS-400, CS-440, CS-4600,
CS-5000. For Generators / Pumps Spring Fits models: PB-200 and 202.
Trimmer Spring - Fits models: SRM200,
202, 300, 302, 351 and 400.
10001130830
550-103
O.E.M
625-477
Clutch Spring
For Chain Saw models:
452, 601 and 602.
Size: ____” diameter, ____ Overall Length
574-248
Part#
Starter Spring
For Chain Saw models 451, 452, 500,
550, 600, 601, 602, 650, 701, 702,
750, 5500, 6700 and 8000. Fits John Deere
models: 50V, 60, 70, 55EV, 65EV, 80EV and 60170.
Clutch Spring
For Chain Saw model:
CS - 60.
Size: ____” diameter, ____ Overall Length
621-108
continued
177220 0653 0
Fits chain saw models: CS-280,
CS-290 and CS-330. Trimmer Spring Fits models: KE140, 200 GT-140, 160,
200, 1000, SRM140, PB300E, PB210, PB211,
SRM200, SRM200AE, SRM210E, SRM250E and PB330
705-574
A
T-Wrench
Fits chain saw models: 100,
315, CS451, 452, 550, 601,
602, 605, 660, 702, 802, 4500,
5500 & 8000Size: A= 7”, B= 1-1/16”, C= 1”.
Bar= 1/2” (13mm), Plug= 3/4” (19mm)
B
C
FRONTIER
605-808
Frontier
AYP# 35373
Jonsereds# 100251
Air Filter
For Chain Saw model Mark-1,
also found on small Husky, Jonsereds and
Pioneer models. Measures: 3-7/8” L X 2-3/8”W
560-147
Frontier
Starter Pulley
For all old style Frontier Chain Saw
models without anti - vib.
Found on Small Husky, Jonsereds
and Pioneer models that were made by Frontier.
625-325
100073
Starter Spring
For all Frontier Chain Saw models.
(Spring and metal band) Note: will also
replace Frontier# 100573 - if you reuse the metal case
16-06
C
CHAIN SAW ACCESSORIES - O.E.M
HOMELITE
Part#
O.E.M
605-121
69681 / A65178
HOMELITE
Application
Air Filter
For Chain Saw models
Super Mini, EZ- Automatic
and Super EZ.
Size: 4” L X 2-7/8” W X 1/16” HT.
605-105
587741 / 63589 A
D92702B
A24779 / 69141
70310-98
7031098
Application
63744A
63745A
A-69923
02500
Fuel Filter Assembly
Use with 1/8” ID fuel line. (felt material).
Found on many older Homelite chain saws.
Measures: 1-1/2” Long X 9/16” diameter
610-022
63225 / 93039
64083 / 640831
Fuel Filter
Felt Replacement felt filter
(Sold in multiples of 10)
for our 610-014 in-tank fuel filter.
Fuel Filter for many Poulan chain saw models.
Measures: 1” Long X 1/4” ID X 9/16” OD.
69254-1A / 69254-2
802202
A00440
610-006
Chain Adjuster
Fuel Filter Assembly
Use with 1/8” ID fuel line. (felt material)
Found on many older Homelite chain saws.
Measures: 1-1/2” Long X 13/16” diameter.
For Chain Saw models XL, XL-2,
Super 2, VI Super 2, 240 and 245.
621-110
115-645
610-014
Chain Adjuster
For Chain Saw models XL12, SuperXL,
410, 450, 540. Also fits chain saw model 550
651-397
O.E.M
Molded Fuel Line
For chain saw models
XL-12 and Super XL-12. Measures: 9” overall length
with a .308” OD grommet at 6-5/16”
Air Filter
Fits Chain Saw models 180,192
and 200 - also fits Little Red XL,
Super 2 and Green Machine model 20
651-396
Part#
610-212
Air Filter
Fits Chain Saw models
XL, XL-2 and Super 2.
Size: 2” L X (1-3/8” - 1-5/8”) W X 1/2” HT
605-143
continued
Homelite Fuel Line (50 FT)
For use on Homelite
and McCulloch Chain
Saws and Trimmers.
Measures: 7/64” (.109”) ID X
13/64” (.209”) OD with a 3/64” (0.047”) wall thickness.
Sold and Priced in 50 foot rolls, Gray in colour.
Air Filter
For Chain Saw models
XL-12 and Super XL.
Size: 4” L X 3-1/2” W X 3/4” HT
605-139
Banta
65842
610-030
Clutch Spring
59253 / 592531A
For Chain Saw models: XL-113, XL-114 and XL-122.
Fuel Filter - Felt
Replacement felt filter for our
(Sold in multiples of 10)
610-006 in-tank fuel filter.
Measures: 1” Long X 7/16” ID X 13/16” OD.
572-195
Piston Assembly (46mm)
For chain saw model:
XL-Super.
623-597
613-601
637781
Fuel Filter - In Tank
Our most popular filter for small Homelite
and McCulloch trimmers and chain saws. Also fits many
other applications. Measures: 1-1/4” long X 1/2” diameter.
Head Gasket
For Chain Saw models XL-922, 923, 925
and Concrete Saw model XL-98 Cut-off saws.
610-345
550-102
63718 / 69451
UP06862
Duck Bill Valve
For chain saw models XL, XL-2 and Super 2.
Duck Bill Valve - Found on Trimmers and Chain Saws.
Measures: .100” ID X .201” OD X .25” L
C
49422 / 96639
UP 0387
DA92701C
Fuel and Oil Cap Kit
Fits chain saw models XL,
XL-2, Super 2, VI Super 2,
180, 190, 200, LX30, 240 and Super 240.
Kit includes: (1) fuel and (1) oil cap shown
16-07
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
HOMELITE
HOMELITE
continued
Part#
O.E.M
600-874
94711A
94711B
94711BS
94711CS
UP03903
Application
Electronic Module
Fits Chain Saw models
XL, XL-2, Super 2,190, 240,
245, P100-1, Super 200 and 240,
also fits trimmer models ST-100, 120, 145, 155, 160A,
180, 200, 210, 245, HB-280, 380, 680 and HD-480.
600-957
A79261
A79641
A94111S
59274
68748
A59052A
A68748
UP06580
Muffler / Exhaust
Muffler for Chain Saw newer
model XL-12. New (3) bolt style,
comes complete with bolts, spacers and baffle.
Size: 3-7/16” X 2-7/8 X 2-5/16” Depth. (3) 3/16” ID
mounting holes. The top (2) mounting holes are on 2-7/8”
centers. Exhaust intake hole measures: 1-9/16” X 5/8”.
Picture shows Top and Bottom views (1) muffler only > NOTE: Will
fit old style (2 bolt) type but you will have to cover the third hole.
560-300
97768A / PS03117
UP05460
Starter Spring
For Chain Saw model 330.
Generator / Pump Spring
Fits models: HB 280, 480 and 680.
625-116
94842 / A94842
Starter Spring
For Chain Saw models XL-12,
XL-15, Super XL, Super XL-AO
and XLBC-4 and XL-Automatic
Trimmer Spring - Fits model: ST400.
A98326
705-534
B
C
T-Wrench
Fits chain saw models:
Super XLAO, XL-12
Size: A= 7”, B= 1-9/16”,
C= 1-1/2”. Bar= 5/8” (16mm),
Plug= 3/4” (19mm)
A
T-Wrench
Fits chain saw models:
XL-76, XL-130 & “C” series.
Size: A= 7”, B= 1-5/8”,
C= 1-9/16”. Bar= 5/8” (16mm),
Plug= 13/16” (21mm)
HUSQVARNA
605-085
530 02 98-11
Air Filter
Fits chain saw models:
136, 137, 141, 142, 36 and 41.
605-066
503 15 19-03
605-173
501 80 71-01
501 80 71-05
69217
Starter Spring
For Chain Saw models: XL,
XL-2, Super 2, 190 and 240.
Trimmer Spring - Fits models:
ST80, 100, 120, 200 and 210.
C
A94918A
Application
Air Filter
Nylon mesh style
Fits Chain Saws
models 238 and 242.
Sarter Pulley
For Chain Saw models XL, Super 2,
240, 245, 250, 300 and Trimmer
models ST-80,100 & 200. Measures: 2-9/16” OD
625-107
625-115
705-535
Chainsaw Exhaust Gasket
(While Quantities Last)
Muffler exhaust gasket for
chain saw models XL-12 and Super XL-AO.
636-409
O.E.M
Starter Spring
For Chain Saw
models 290 and 340.
Note 1: You will have to reuse your original Pioneer lamination.
For Pioneer P41 applications we DO NOT recommend purchasing
unless you have some small engine repair knowledge. Note 2:
BANTA purchases these modules from the O.E.M. vender and
there is “No Warranty” on these modules. They are tested by the
Manufacturer before they are shipped. The most important thing
to remember when installing a 600-957 is that you have a good
ground connection. (Prestolite Module - Blue). Our 600-957 WILL
NOT replace Phelon module Pioneer# 430938 / 507-430938).
623-322
Part#
625-117
Electronic Ignition
Fits Chain Saw models
XL-76, XL-130 & Super Mini.
Will also fit Pioneer Chain Saw
model P-41 if the original
Pioneer lamination is reused.
continued
Air Filter
(While Quantities Last)
Fits Chain Saw models
61, 66, 261, 266, 281 & 288.
Nylon mess style (2 bolt)
Size: 3-1/2” L X 3.735” W X 1-3/8” HT
16-08
C
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
Part#
O.E.M
605-062
503 81 45-02
503 81 45-03
575 26 91-03
Application
Air Filter
For Chain Saw models
362, 365, 371 & 372.
Size: 3-5/8” L X 2-7/8” W X 1-5/8” HT
605-159
506 26 34-01
506 26 34-02
Air filter
For Cut-off Saw
Size: 3-23/32” L X 3-3/4” W X 2-1/16” HT.
Note: Two images shown for reference.
605-160
506 26 91-01
Pre Filter
For our 605-159.
Fits cut-off saw models: 371K
and 375K. 3 layer foam filter.
Size: 7-5/8” L X 4-7/8” W X 3/4” HT
605-156
Note: Two images shown for reference
(For use with our pre filter 605-155).
506 26 86-01
Pre Filter
For cut-off saw. Fits model:
3120K. 3 layer foam filter.
Size: 8” L X 6” W X 3/4” HT.
605-440
506 23 19-01
Pre Filter
(3) Layer foam filter.
Fits models: K950 Active and K960 Cut Quik saws.
Size: 10-3/8” L X 5-1/4” W X 3/4” HT approximately.
(Also see our 605-438 Air Filter)
605-024
503 44 72-03
503 44 72-04
Air Filter
Fits chain saw models:
262, 268, 272, 394.
Size: 3-9/16” L X 2-9/16” W Overall Height: 1-1/4”.
C
O.E.M
605-064
503 89 81-01
503 89 81-02
Application
Air Filter
Fits chain saw models: 51 and 55.
This filter is the commonly used flock design.
Air filter is held in place with a screw
(screw provided). Oil-less type filter.
605-060
537 02 40-03
Air Filter. (Twist on)
Fits the following chain
saw models: 340, 345,
346, 350, 351 and 353;
Air filter attaches by simply twisting on
the carburetor manifold. Note: Some 346 and 353 models use a
steel snap to connect. See picture for clarification.
605-028
503 44 72-03
Air Filter
Assembly for chain saw
models: 262, 268, 272 & 394.
605-378
506 36 72-01
506 36 72-02
544 18 16-01
Panel Air Filter
For Concrete / Cut Quik Saw
model: K750.
Base Size: 4-15/16” L X 4-1/2” W X 1-3/8” HT.
(For use with our 605-377 pre filter)
605-377
506 36 71-01
506 14 57-01
Pre-filter
For our 605-156. Fits Cut-off
Saw models 268K and 272K.
Note: Image shows both top
and side (3 laminated layers for filtration).
Size: 5” L X 4-1/2 to 4-7/8” W X 3/4” HT.
605-171
continued
Part#
506 14 58-01
Air filter
For Cut-off Saw model
268K and 272K.
Size: 4-1/16” L X 4” W X 3-3/16” HT
605-155
HUSQVARNA
continued
Banta
Pre filter
Fits Cut Quik Saw model: K750.
Size: 7-5/64” L X 5-1/2” W X 13/16” HT.
(Use with our 605-378 air filter)
605-063
537 20 75-01
Air Filter
Fits models: 570,
575 and 576. Nylon mesh style.
Size: 3-3/8” L X
3-1/4” W X 2-1/8” HT approximately.
Note: Air filter only, does not include knob or mounting screw.
605-460
505 31 55-30
Air Filter
For Husqvarna and Partner concrete /
cut quik saws. For Husqvarna
model: K185 and Partner models:
K1200 and K1200 Mark II.
Size: 5-7/8” OD X 4-1/8” ID X 2-1/2” HT
670-101
503 22 00-01
Bar Nut (8mm)
(Sold in multiples of 10)
Fits many chain saw
manufacturers chain saws.
Fits models: 41, 44, 444, 50, 51, 55, 61,
66, 162, 181, 266, 268, 280, 285, 380, 2100 etc.
Size: 8mm X 1.25 thread. For 13mm T-wrench
16-09
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
Part#
O.E.M
653-126
501 81 48-01
Bar Plate
For chain saw models 61,
66 and 266. (New Style)
653-127
HUSQVARNA
continued
Application
(While Quantities Last)
537 01 37-71
738 22 02-25
506 07 05-20
506 34 74-20
506 34 74-23
506 37 27-03
506 37 27-20
506 29 67-02
544 90 84-02
For concrete saw model: K750.
Size: .551” W X 32” L
(6 rib, polyester cord construction)
501 69 94-01
501 77 35-01
Av Buffer
Anti Vibration Dampings (Large) for chain saw models: 61,
162 (new), 66, 266, 268 and 272 with plastic crankcase.
Measures: 7/8” OD X 1-5/16” overall length
657-124
501 81 47-01 / 501 81 47-02
501 76 39-02
503 85 41-01
Anti Vibration Dampings
For chain saw models: 340, 345, 346,
350, 351, 353, 357, 359, 455 and 460.
Measures: 19.85mm OD X 48mm Overall Length. This
measurement does not include the internal threaded bolt.
657-127
503 52 87-02
501 53 05-01
Av Buffer
Anti Vibration Dampings
For chain saw models: 61, 162 (old) and 480, with metal
crankcase. Measures: 5/8” OD X 15/16” overall length
AV Buffer
Anti Vibration Dampings
for chain saw models: 394 and 395. (2003 thru 2010)
Measures: 19mm OD X 52mm Overall Length.
This measurement does not include the internal threaded bolt.
657-126
501 27 23-01
501 27 63-01
Av Buffer
Anti Vibration Dampings for chain saw models: 61, 162
(old) & 480, with metal crankcase. Size: 7/8” OD X 1-3/32”
overall length. Also found on some Makita / Dolmar saws.
C
Av Buffer
Anti Vibration Dampings (Medium)
for chain saw models: 36, 41, 42, 61, 66, 136, 141, 162
(new), 238, 242, 246, 266, 268 and 272 with plastic
crankcase. Also fits cut quik saw models: 268K and 272K.
Measures: 3/4” OD X 1-1/16” overall length.
657-137
506 03 30-31
506 27 67-41
Drive Belt (cogged)
657-122
501 62 87-01
AV Buffer
Anti Vibration Dampings for chain saw
models: 50, 51, 55 and 55 Rancher. (1984 thru 2007)
Measures: 5/8” to 11/16” Tapered OD X 1-5/16” overall height.
For concrete saw model:
K650 Active, K650 Active II
& K700 Active II. Size: 1/4” W X 31-1/2” L
657-123
Anti Vibration Dampings (Light)
For chain saw models: 36, 41, 42, 61, 66, 136,
141, 162 (new), 238, 242, 246, 266, 268 and 272 with
plastic crankcase. Also fits Husqvarna cut quik saw
models: 268K & 272K. Fits Jonsereds saw model: 670.
Measures: 5/8” OD X 1-1/16” overall length.
657-125
506 07 05-04
506 34 74-24
Drive Belt (cogged)
For concrete saw model:
K950 Active with 16” blades.
Size: 3/8” W X 36” L
875-711
501 62 87-01
Application
AV Buffer
Anti Vibration Dampings for chain saw
models: 181, 262, 281, 288 and 3120.
Measures: 15/16” OD (coarse threaded male end),
13/16” OD (fine threaded female end) X 1-1/2” overall length.
Drive Belt (multi-rib)
875-725
657-131
657-133
Drive belt (cogged belt)
Fits models: 371K and 375K cut-off saws & Partner K950 cut
off saws with 12” and 14” blades. Size: 3/8” W X 34-1/2” L
875-712
O.E.M
657-132
Crankshaft Bearing
Fits many Chain Saw models.
Measures: 15mm ID X 35mm OD X 11mm HT (Bearing# 6202)
875-724
Part#
(For larger diameter (Medium) Av buffer see our 657-132).
Bar Plate
For chain saw models:
362, 365, 372 and 385.
592-106
continued
503 63 75-03
AV Buffer
Anti Vibration Dampings for chain saw
models: 362, 362 XP, 365, 371, 372
and 575. (Hard), Front upper handle (1999 - 2007)
Measures: 18mm OD X 46mm Overall Length.
This measurement does not include the internal threaded bolt.
16-10
C
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
657-128
503 63 76-02
Application
AV Buffer
Anti Vibration Dampings
For chain saw models: 362,
362 XP (1999 thru 2005), 365 (1996 thru 2009), 371 (1999
thru 2004), 372 (1999 thru 2011) (HARD), Rear AV / anti
vibe mount. Measures: 22mm OD X 46mm Overall Length.
Will also replace Husqvarna# 503637601 (Std). Overall
measurement includes threaded (5mm) female insert piece.
657-129
503 89 56-02
501 43 27-01
501 45 27-02
501 81 73-01
501 81 92-01
Chain Adjuster
For chain saw models: 55, 154 and 254.
651-113
501 15 43-02
501 22 68-01
501 24 81-01
Chain Adjuster
For chain saw models: 65, 77, 180, 280 & 380.
651-175
537 07 12-01
Chain Adjuster Assembly
For chain saw models:
340, 345, 346, 350, 351, 353, 357 and 359.
(Includes part#’s 503869101 and 503885401);
C
Chain Adjuster
For chain saw models: 362,
362 XP, 365, 372, 385, 570, 575 and 576.
651-138
503 46 77-01
501 20 87-01
501 40 34-02
Clutch Spring
For chain saw models: 61, 66, 162, 266 and 266 XP.
621-145
501 40 45-01
Clutch Spring
For chain saw models: 44 and 444.
621-112
Clutch Spring
For chain saw model: 35 and Jonsereds model: 361, also
Pioneer model P12. That were manufactured by Frontier.
621-156
Chain Adjuster
For chain saw models: 44, 50, 50 Rancher, 238 and 444.
651-192
537 04 04-21
537 04 41-02
537 07 95-01
621-144
501 45 27-01
501 45 27-02
501 45 41-01
501 54 63-01
Chain Adjuster
For chain saw models: 51,
61, 162, 181, 266, 268 & older model 272 XP;
also found on older Jonsereds models 630 & 670.
651-174
Application
For chain saw models 65, 77 and 380.
503 74 39-01
501 53 71-01
O.E.M
Clutch Spring
Carburetor Rubber Elbow
Intake Manifold - Rubber. Fits chain saw
models: 362, 365, 371 and 372.
651-172
Part#
621-111
Will also replace Husqvarna# 503895601 (Std) . Overall
measurement includes threaded (5mm) female insert piece.
651-173
continued
Chain Adjuster
For chain saw models: 394, 394 XP, 395 and 395 XP.
AV Buffer
Anti Vibration Dampings
For chain saw models: 362,
362 XP (1999 thru 2005), 365 (96 thru 2009),
371 (99 thru 2004), 372 (1999 thru 2011) (HARD),
Front AV / anti vibe mount.
Measures: 22mm OD X 46mm Overall Length.
606-316
Banta
504 21 00-16
Clutch Spring
For Chain Saw models 40 and 41
621-114
501 45 61-01
Clutch Spring
For models: 50, 51, 55, 55 Rancher, 244R, 244RX,
254, 257, 261, 36R, 44, 444. Overall Length: 5-3/8”.
621-115
503 14 51-01
Clutch Spring
For models: 281, 288, 3120, 334T, 335XP,
336, 338, 339, 385, 390, 394, 395, K960 and K1250.
Overall Length: 1-1/8” X 7/16” OD.
646-150
501 45 54-03
Clutch Assembly
For chain saw models: 50,
51, 55, 54, 254, 257 and 261.
Measures: 2.610” OD X 0.453” Thick.
646-152
537 10 34-01
537 10 34-03
Clutch Assembly
For chain saw models:
357 and 359.
Measures: 2.640” OD X 0.400” Thick.
16-11
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
646-153
501 77 85-01
501 77 85-02
503 52 79-01
503 74 44-02
Application
Clutch Assembly
For chain saw models: 61, (after
Serial# 602497), 66, 266 (after serial# 6051313), 268 and 272.
Measures: 3.057” OD X 0.475” Thick.
646-113
Part#
O.E.M
570-264
503 50 39-01
503 50 39-02
503 50 39-03
Clutch Assembly
For chain saw models:
362, 365, 371, 372, 385, 390 and 575.
Measures: 3.057” OD X 0.471” Thick.
570-284
503 70 15-02
H340
Cylinder Assy. (40mm)
Fits chain saw model:
H340.
Cylinder Assy. (42mm)
Fits chain saw models:
242 and 242XP.
C
55
Note: This will also fit on
the smaller bore model 51
570-283
503 53 68-01
503 53 68-02
503 16 91-71
503 60 91-02
503 60 91-08
503 60 91-72
Cylinder Assy. (46mm)
Fits chain saw model:
55.
Clutch Assembly
For chain saw models:
281, 288 & 395 (after Serial# 003900001)
Measures: 3.045” OD X 0.542” Thick.
570-254
51
(For 46mm cylinder
assembly see our 570-284)
503 74 44-01
503 87 00-73
503 16 83-01
503 60 91-71
Cylinder Assy. (45mm)
Fits chain saw model:
51.
(Also see our 646-153 newer style).
570-241
254 & 254XP
Cylinder Assy. (45mm)
Fits chain saw models:
254 & 254XP.
570-285
646-155
Application
501 77 85-01
Clutch Assembly
For chain saw models:
61, 66, 266, 266XP, 268 and 272;
Measures: 3.057” OD X 0.512” Thick.
646-154
continued
537 15 73-02
359 & 357XP
Cylinder Assy. (47mm)
Fits chain saw models:
359 and also 357XP.
242 & 242XP
570-252
503 53 20-71
61
Cylinder Assy. (48mm)
Fits chain saw model:
61.
16-12
C
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
570-260
503 54 11-71
503 54 11-72
503 90 79-71
Application
262
570-282
501 41 78-01
O.E.M
Application
570-287
503 62 64-72
503 62 64-73
503 93 90-05
503 93 93-71
503 93 93-72
503 96 52-71
362 &371
Cylinder Assy. (52mm)
Fits chain saw models:
362, 371, 372 and 375.
65 & 265
503 69 10-73
503 93 90-03
570-270
506 386 171
520 757 302
K750
Cylinder Assy. (51 mm)
Fits cut quik saw models:
K750.
Cylinder Assy. (48mm)
Fits chain saw models:
65 and 265.
570-286
continued
Part#
Cylinder Assy. (48mm)
Fits chain saw models:
262.
Note: Decompression valve
NOT included, use our 570-003
De-compression valve. Bore: 48 mm,
Stroke: 34 mm, Displacement: 62 cc,
Rings: 48 mm X 1.5 mm.
Banta
365
Cylinder Assy. (48mm)
Fits chain saw models:
365.
570-288
503 90 74-01
503 90 74-71
181, 281 & 288
Cylinder Assy. (54mm)
Fits chain saw models:
181, 281 and 288.
570-280
501 65 85-71
503 61 10-71
544 22 29-02
268 & 268S
Cylinder Assembly (50mm)
Fits chain saw models:
268, 268 S,
268 K and 268 XP.
570-289
Note: Dealers have used
this Cylinder and Piston on
Husqvarna Chain Saw
model 272. Same as our
570-279 but 2mm smaller
bore and does not include a
hole for a decompression valve.
Uses our 572-524 replacement piston assy.
570-279
503 60 96-71
503 75 81-71
503 75 81-72
504 01 68-02
Cylinder Assembly (52mm)
Fits chain saw models:
272, 272K.
Same as our 570-280
but this cylinder assembly
has a hole for a decompression
valve and has a 2mm larger bore.
(Note: Cylinder Plug only included
for decompression valve
see our 570-002 or 570-003).
Uses our 572-715 replacement piston assy.
C
503 99 39-71
395
Cylinder Assy. (56mm)
Fits chain saw models:
395.
272 & 272K
570-271
506 15 55-06
K950
Cylinder Assy. (56 mm)
Fits cut quik saw model:
K950.
16-13
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
570-269
506 29 42-71A
Application
K1250, 3120
& 3120K
Cylinder Assy. (60mm)
Fits chain saw models:
K1250, 3120 and 3120K
continued
Part#
O.E.M
572-708
537 29 30-02
Application
Piston Assembly (47mm)
Fits chain saw model:
455.
572-499
503 53 90-02
Piston Assembly (48mm)
For chain saw model:
61.
Note: Will also fit Jonsereds chain saw model 630.
572-501
572-526
503 51 32-01
Piston Assembly (48mm)
For chain saw models:
65 and 265.
Piston Assembly (42mm)
For chain saw models:
242 and 242XP.
572-701
(While Quantities Last)
503 73 02-71
572-714
Piston Assembly (44mm)
Fits chain saw models:
246.
572-700
503 89 96-71
572-710
503 16 77-01
572-524
503 60 81-01
503 60 81-71
Note: Will also fit Jonsereds model 670.
572-807
503 92 04-71
537 21 96-02
NOTE 1: Also fits Husqvarna chain saw model: 272
(older models) and will fit model: 266 / 266 XP with 50mm bore.
NOTE 2: Our 572-524 piston assembly was also used in older
Husqvarna 268 models - see actual piston pictures for proper
reference. For 52mm piston assembly see our 572-715.
Note 1: Replaces Husqvarna# 503 92 04-71 before SN 020700001
Note 2: This Piston Assembly will also work in chain saw model 257.
Note: Dealers have also used this piston
assembly in Jonsereds chain saw model: 2059.
C
572-718
537 15 72-02
Piston Assembly (47mm)
Fits chain saw model: 359.
501 65 88-03
Piston Assembly (50mm)
Fits selected 670 Jonsereds
chain saw models.
Piston Assembly (46mm)
Fits chain saw model:
357.
572-705
501 65 94-03
Piston Assembly (50mm)
For chain saw models:
268, 268 S, 268 K & 268 XP.
Piston Assembly (46mm)
Fits chain saw model:
55, older style.
572-706
503 53 11-71
Piston Assembly (48mm)
Fits chain saw model:
262.
Piston Assembly (45mm)
Fits chain saw models:
51.
572-704
503 69 13-71
Piston Assembly (48mm)
Fits Chain Saw model:
365.
(Replaces our old# 572-806)
Piston Assembly (44mm)
Fits Chain saw models:
350 & 351.
572-703
501 20 56-03
503 28 90-42
503 69 12-71
503 69 14-71
503 93 92-71
Piston Assembly (50mm)
Fits chain saw models:
362, 371 & 372 (pre 1998).
Note: Will also fit Jonsereds chain saw models: 2071 and 2171
16-14
C
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
572-712
537 32 85-02
Application
Piston Assembly (51mm)
Fits chain saw models:
575 & 299. (51mm X 1.2mm).
572-715
continued
Part#
O.E.M
572-723
503 48 87-03
503 60 98-02
503 60 98-03
572-730
501 89 41-03
Piston Assembly (60mm)
Fits chain saw models:
3120 / 3120 EPA.
503 50 27-02
574-200
530 02 96-05
530 02 98-05
Piston Assembly (52mm)
Fits chain saw model:
281.
Piston Ring Set (38mm X 1.5mm)
Fits chain saw models:
36, 136, 137 and 235.
572-719
574-206
574-212
574-159
503 28 90-05
Piston Ring (42mm X 1.5mm)
Fits Chain Saw models:
242 and 242 XP
537 16 98-71
574-216
Piston Assembly (54mm)
Fits chain saw model: 385
503 28 90-10
Piston Ring Set (44mm X 1.5mm)
Fits chain saw models:
49, 50, 51 EPA, 350 and 351.
Note: Piston rings = 1.2mm thick
572-724
503 28 90-05
Piston Ring Set (42mm X 1.5mm)
Fits chain saw models:
42, 45, 242, 246, 345 and 346.
503 50 60-02
Piston Assembly (54mm)
Fits Chain Saw model :
288 (older style).
572-717
503 28 90-02
Piston Ring Set (40mm X 1.5mm)
Fits chain saw model:
141, 142 and 340.
Piston Assembly (52mm)
Fits chain saw model:
285.
572-720
537 42 02-02
574-161
503 28 90-11
Piston Assembly (55mm)
Fits chain saw models:
390, 390XP & 390 XPW.
Piston Ring (45mm X 1.5mm)
For chain saw models:
254 and 254XP.
Note: Piston Rings = 1.2mm thick
574-221
572-721
574-230
Note 1: Piston rings measure 1.5mm thick
Note 2: Overall Height = 49mm, (1mm) higher than our 572-722.
537 13 76 71
Piston Assembly (56mm)
Fits chain saw model:
395.
Note 1: Piston Rings = 1.2mm thick
C
503 28 90-14
Piston Ring Set (46mm X 1.5mm)
Fits chain saw models:
55, 257, 357 and 359.
503 46 02-02
Piston Assembly (56mm)
Fits chain saw model:
394.
572-722
Application
Piston Assembly (56mm)
Fits chain saw model:
2101.
Piston Assembly (52mm)
Fits chain saw model:
272P.
572-716
Banta
503 28 90-29
Piston Ring Set (47mm X 1.5mm)
Fits chain saw models:
359 and 362.
574-157
501 20 50-01
501 20 56-02
503 28 90-15
Piston Ring (48mm X 1.5mm)
For chain saw models:
61, 65, 265.
16-15
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
574-137
501 69 98-01
503 28 90-17
Application
503 28 90-42
Piston Ring Set (50mm X 1.5mm)
Fits chain saw models:
266, 268, 362, 371 and 372.
574-248
590-149
501 52 84-02
738 22 02-25
503 28 90-19
590-165
503 28 90-22
503 61 33-71
Crankshaft Assembly
For chain saw models:
61, 66, 266, 266 XP, 268,
268 XP and 272; after 1993
640-354
503 28 90-24
Piston Ring Set (56mm X 1.5mm)
Fits chain saw models:
394 “Non EPA” and 2101.
Gasket Set
Fits chain saw models:
254 and 257.
NOTE: Some chain saw
applications use only one piston ring.
640-243
570-001
Gasket Set
Fits chain saw
models: 61 and 66.
(Includes oil seals)
Many Applications
Cylinder Plug
Fits Dolmar, Husqvarna, ICS, Makita,
Partner, Stihl and Wacker cylinder assemblies.
640-220
(For Decompression Valve see our part# 570-002)
570-002
Application
Crankshaft Bearing
Found on many models.
Measures: 37/64” ID X 1-3/8” OD X 7/16” HT.
Measures: 15mm x 35mm x 11mm
(Bearing# 6202 - open both sides)
Piston Ring Set (54mm X 1.5mm)
Fits chain saw model:
288.
574-260
O.E.M
592-106
Piston Ring Set (52mm X 1.5mm)
Fits chain saw models:
272 and 281.
574-254
Part#
Crankshaft Assembly
For Husqvarna chain saw
models: 61, 66, 266, 266 XP,
268, 268 XP & 272; older
models before 1993 with
larger flywheel nut.
Piston Ring (50mm X 1.5mm)
Fits Chain saw models:
266, 266 XP, 268, 268 S, 268 K and 268 XP
574-242
continued
503 66 56-01
503 71 53-01
Decompression Valve
For Chain Saw and Concrete Saws. Fits models: K650
and K700 Active I, II and III, K750, K950 and K1250.
Gasket Set
Fits chain saw models:
266, 266 XP and 162.
(Includes oil seals)
640-183
(For plug only see our part# 570-001)
570-005
503 66 56-01
Gasket Set
Fits chain saw models:
268 and 268 XP.
Decompression Valve (Blue Knob)
For Chain Saw and Concrete saw cylinder assemblies.
Fits Husqvarna, Jonsereds & Partner models: K1250 etc.
Overall Length: 1-7/8” - Blue knob with 2 holes in nut.
Similar to our 570-003 but with a longer main body.
570-003
503 71 53-01
Decompression Valve
For Chain Saw and
Concrete saw cylinder assemblies.
Fits models: 254, 257, 261, 262, 268, 272, 281, 288,
357, 359, 362, 365, 371, 372, 385, 394 and 395 etc.
Overall Length: 1-7/16” - Blue knob with 2 holes in nut.
C
640-224
Gasket Set
Fits chain saw models:
365 and 372.
(Includes oil seals)
640-371
Gasket Set
Fits chain saw model:
271.
16-16
C
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
Part#
HUSQVARNA
continued
Banta
continued
Part#
O.E.M
640-388
613-603
503 44 32-01
Gasket Set
Fits chain saw model:
288.
Fuel Filter - In Tank.
Fits chain saw models: 36, 40, 41,
42, 45, 50, 51,55, 61, 66, 394 and many others.
Use with 3/32” or 1/8” ID fuel line.
Measures: 1-5/8” long X 11/16” diameter.
O.E.M
Application
640-394
Gasket Set
Fits chain saw model:
394.
640-235
Gasket Set
For chain saw model:
Rancher 50.
640-360
506 38 53-05
610-141
Application
501 28 59-01
501 28 59-02
503 50 97-01
Molded Fuel Line
Fits chain saw models: 61, 66, 266 etc.
Measures: 5-1/16” overall length.
610-151
501 51 99-01
Oil Pipe
For chain saw models: 61, 266 and 266 XP.
(Also found on Jonsereds Chain Saw model 630)
550-151
Gasket Set
Fits cut quit / concrete saw
models: K750 and K760.
640-186
Gasket Set
Fits Husqvarna / Partner
cut quit / concrete saw model:
K950. (Includes oil seals).
623-820
501 51 22-01
Gas Cap
For chain saw models: 36, 41, 42, 50, 51, 55, 154, 181,
234, 238, 254 / XP, 262, 281, 288, 345, 365, 394, 3120 also fits Cut-off Saw models 371K, 375K and 3120K.
Gas & Oils Cap
For Chain Saw models: 181, 281, 288, 394.
551-107
Head / Base Gasket
For chain saw models:
61, 162, 66, 266 & 266XP
623-751
503 49 10-02
503 49 10-01
Head / Base Gasket
Fits chain saw model: P-650 and
concrete saw models: K-650
(both old and new) and K700, Active I, II and III.
623-822
503 96 15-01
Head / Base Gasket only
Fits chain saw models: 362, 365, 372,
372 & 375; also fits Jonsereds models:
2065, 2071, 2162 and 2171.
C
Gas Cap
For chain saw models: 44, 61, 66, 162, 65, 77 (new),
266 / XP, 268 / XP, 272, 380, 480, 2100 and 2101
551-153
506 15 82-01
Head / Base Gasket
For cut quik / concrete saw
models: K950.
623-868
501 43 14-01
501 43 14-02
501 56 45-01
501 56 45-02
501 56 45-04
501 76 56-02
506 37 67-01
Head / Base Gasket
For cut quik / concrete saw models:
K750 and K760.
623-499
501 81 96-01
501 81 96-02
530 07 12-66
537 21 52-02
501 76 56-01
501 76 56-02
Oil Cap
For chain saw models: 36, 41, 50, 51,
55, 136, 141, 154, 254, 254XP, 257, 261 and 262.
551-145
501 62 66-01
Oil Cap
For chain saw models:
44, 61, 66, 162, 234, 238, 266,
266 XP, 268, 268 XP and 2100.
627-061
501 51 33-10
501 51 38-01
Oil Pump Drive Gear
This nylon gear fits chain saw
models: 61, 66, 266, 268 and 272.
16-17
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
627-072
503 75 61-02
Application
Part#
O.E.M
600-162
503 96 24-01 / 503 96 24-02
503 96 24-03 / 503 96 24-04
503 96 24-05 / 503 96 24-06
537 16 21-01 / 537 16 21-04
537 16 21-05 / 537 16 22-01
537 16 22-04 / 537 27 74-01
544 04 70-01 / 544 04 71-01
544 04 72-01 / 544 04 72-02
Oil Pump Worm Gear.
Fits chain saw models: 362, 365, 371, 372 & 375.
627-266
501 51 25-01
501 51 38-01
501 83 17-01
Oiler / Oil Pump Assembly
Fits chain saw models:
61, 66, 266, 268, 272. Includes all three pieces shown.
627-281
503 69 81-01
Application
Ignition Module
For chain saws.
(Non RPM Limited).
Fits models: 334, 335,
336, 338, 339, 340, 345, 346, 350, 351,
353, 357, 359, 362, 365, 371, 372, 385, 390, 570 & 575.
430-163
Oil / Oil Pump Assembly
Fits Chain Saw models: 281 and 288
627-270
continued
501 52 66-02
503 08 97-02
503 71 79-01
503 91 79-01
On / Off Switch
For Chain Saw models: 36, 41, 50, 51, 55, 61,
266, 266 XP, 268, 268 XP, 272, 281, 340, 345, 394 & 395.
503 52 13-01
503 52 13-05
(Made to O.E.M. Specs.) Two pictures shown for reference
430-180
Oiler / Oil Pump Assembly
Fits chain saw models: 365,
371, 372, 385, 390, 570 and 575.
600-185
503 71 82-01
Stop Switch or On / Off Switch
For Chain Saw models: 232L, 232R,
235FR, 235R, 324LDX, 324LX,
324RX, 326, 336, 339XPT, 385. For Trimmer models:
123C, 123HD, 123L, 123LD, 225AI, 225B, 225BX, 225E,
225H, 225HBV, 225L, 225LD, 225 LITE, 225R, 225RD,
225RJ, 227L, 227JD, 227R, 227RD, 227RJ, 232L, 232R,
232RD, 232RL, 235R, 235RL, 240, 240R, 240RBD.
503 62 02-01
503 62 02-02
503 62 02-03
503 90 14-01
506 16 90-02
544 01 84-01
94114601
636-142
503 74 91-01
501 76 66-02
Electronic Ignition
For Chain Saw models: 45, 51, 55, 254, 257, 61, 262,
268, 272 and 394. For Jonsereds model: 630 chain saw.
Muffler / Exhaust
For chain saw models:
51 and 55. Exhaust mounting holes
are 40mm center to center.
Note: Includes spark plug boot, not shown.
(Complete with spark arrester screen.)
600-180
545 06 39-01
530 03 92-39
636-141
Muffler / Exhaust
For chain saw models:
61, 268 and 272. Also fits some
older Jonsereds chain saw models:
625, 630 and 670.
Electronic Ignition
Fits chain saw models: 137, 142
600-164
503 47 69-01
503 59 92-05
501 51 62-01
501 51 62-02
501 61 73-02
This is an aftermarket muffler. Mounting bolts holes are on 40mm
centres. NOTE 1: This muffler is a NON DF version
NOT US Forest Service approved.
636-146
501 81 68-01
Electronic Ignition
Fits chain saw models: 61 (old), 66, 266 and 33
Muffler / Exhaust
For chain saw models:
281 and 288.
The electronic ignition component is connected
with the ignition coil to achieve full ignition. This type of
ignition module utilizes transistor switches for magnet activation.
Mounting bolts holes are on 46mm centres.
NOTE 1: This muffler is a NON DF version
NOT US Forest Service approved
C
16-18
C
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
636-148
503 71 13-05
503 71 13-07
Application
Muffler / Exhaust
For chain saw models:
394, 394 EPA, 395 and 395 EPA.
Part#
O.E.M
650-272
503 73 66-01
650-275
Application
(While Quantities Last)
537 03 35-01
503 71 13-04
Muffler / Exhaust
For chain saw models:
394, 394 EPA, 395 and 395 EPA.
Sprocket Side Cover
For chain saw models: 362, 365, 371, 372, 385, 390 and
575. Note: Chain adjuster and rubber saw chain guard included
Mounting bolts holes are on 52mm centres.
Note: Complete with spark arrester screen.
(Also see our 636-148)
636-143
continued
Sprocket Side Cover
For chain saw models:
61, 266, 268 and 272.
Mounting bolts holes are on 52mm centres.
NOTE 1: This muffler is a NON DF version
NOT US Forest Service approved.
(Also see our 636-149)
636-149
Banta
as shown in picture.
503 76 53-02
503 76 54-02
655-255
503 15 18-01
503 15 18-02 / 503 60 88-03
Muffler / Exhaust
For chain saw models:
362, 365, 371, 372.
Mounting bolt holes are on 53mm centres
Note: Complete with spark arrester screen.
(Also see our 636-145)
636-145
503 76 53-01
Starter Assembly
For chain saw models: 50, 51 and 55. This aftermarket
assembly comes complete with housing, starter pulley,
spring, rope, handle etc. Just needs to be
bolted on. (Made of plastic)
Muffler / Exhaust
For chain saw models:
362, 365, 371, 372.
Mounting bolt holes are on 53mm centres
Note: This muffler is a NON DF version
NOT US Forest Service approved
(Also see our 636-143)
623-033
655-272
501 61 55-71
501 52 25-04
Exhaust / Muffler Gaskets
Fits Chain Saw models:
61, 66, 162, 266 and 266XP.
(Also found on Jonsereds model 630).
560-191
Starter Handle
For most Husqvarna
Chain Saw models,
as well as many
Jonsereds Chain Saws.
135-204
Starter Assembly
For chain saw models: 61, 266, 268, 268K and 272.
This aftermarket assembly comes complete with housing,
starter pulley, spring, rope, handle etc. Just needs to be
bolted on. (Made of plastic)
501 55 14-01
501 55 14-02
503 54 39-01
655-365
(Sold in multiples of 10)
501 48 54-02
Spark Plug Boot with
spring (70 degree)
For chain saw models:
36, 41, 42, 40, 45, 50, 51, 55, 61, 66, 136, 141, 140, 242,
246, 254, 257, 261, 262, 266, 268K, 272K, 288, 335, 340,
345, 346, 350, 351, 362, 365, 371, 371K, 372, 394, 395,
3120, 3120K. (Fits 5mm spark plug wire).
C
503 62 81-71
Starter Assembly
For chain saw models: 362, 365, 371 and 372.
This aftermarket assembly comes complete with housing,
starter pulley, spring, rope, handle etc. Just needs to be
bolted on. (Made of plastic).
Uses our 625-410 replacement starter spring.
16-19
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
655-288
501 81 00-06
Application
continued
Part#
O.E.M
560-182
501 52 07-01
Application
Starter Pulley
For Chain Saw models:
61, 66, 266 & 181 (old).
Measures: 10mm ID
X 2-7/8” OD X 1-11/32” HT
560-211
Starter Assembly
For chain saw models: 281 and 288. (1989 thru 2009).
This aftermarket assembly comes complete with housing,
starter pulley, spring, rope, handle etc. Just needs to be
bolted on. (Made of plastic)
655-250
506 38 56-11 / 506 38 56-12
506 38 56-13 / 574 36 20-01
503 10 24-02
Starter Pulley
For Chain Saw models:
61, 66, 266 & 181 (new).
Measures: 14mm ID
X 2-7/8” OD X 1-13/32” HT
560-253
(While Quantities Last)
(While Quantities Last)
503 10 24-03
503 10 24-05
Starter Pulley (longer hub)
For Chain Saw models:
268, 268XP and 272.
Measures: 14mm ID
X 2-7/8” OD X 1-9/16” HT
Starter Assembly
For concrete / cut quik saw models: K750 and K760.
This aftermarket assembly comes complete with housing,
starter pulley, spring, rope, handle etc. Just needs to be
bolted on. (Uses our 625-430 starter spring).
560-060
503 76 37-01
503 85 95-01
Starter Pulley
For Chain Saw model: 35.
Measures: 8mm / .315” ID
X 2-3/8” (60mm) OD X
1-1/4” Overall Height. 8 Tooth gear X 1-1/8” OD.
560-210
560-242
NOTE: original Husky application is (6) cog.
505 30 37-75
505 30 37-35
Starter Pulley
For Chain Saw models:
51 and 55.
Measures: 12.8 mm or 1/2” ID X
64.52 mm or 2.540” OD X 30 mm or 1.183” overall height.
501 79 44-01
Starter Pulley
For Chain Saw model: 242.
Measures: 12mm ID X
2-9/16” OD X 1-5/16” HT
C
503 85 96-01
503 87 63-01
537 09 25-01
506 25 81-02
Starter Pulley
Fits Concrete / Quik Saw
models: K650 and K950.
Measures: 14mm ID
X 2-7/8” OD X 1-9/16” HT
069313
530 06 93-13
Starter Pulley
Fits chain saw models:
136 and 41.
Dealers use it on Husqvarna model 41 Chain Saw.
May fit other Husky saws? (4) cog pulley.
560-238
(While Quantities Last)
Starter Pulley
Fits Husqvarna chain saw models: 340,
345, 346, 350, 351, 353, 362, 365, 371, 372, 385, 390, 445,
455 and 460. Also fits Jonsered chain saw models: 2141, 2149.
Size: 12.2 mm ID X 68.3 mm OD X 27.7 mm overall height.
560-147
560-241
503 48 48-01
Starter Pulley
Fits chain saw models:
281 and 288. Measures: 14mm ID
X 2-7/8” OD X 1-5/16” HT
560-260
Starter Pawl (steel)
For chain saw models: 362, 365, 371 and 372.
560-368
560-209
(While Quantities Last)
Starter Pulley
For Chain Saw models: 40, 45, 49,
240, 245, 334T, 335XPT, 336, 338 and 339.
Measures: 13 mm or .510” ID X 65.25 mm or
2.566” OD X 29 mm or 1.14” overall height.
625-400
501 52 04-01
Starter Spring
For chain saw models: 61, 61 Rancher,
66, 162, 181, 266, 266 XP, 268 & 272.
625-401
(While Quantities Last)
506 01 64-01
537 20 19-01
501 40 22-01
Starter Spring
For chain saw models: L65, 77, 160,
180, 280, 285, 380 and 480.
16-20
C
CHAIN SAW ACCESSORIES - O.E.M
HUSQVARNA
HUSQVARNA
continued
Part#
O.E.M
625-402
501 46 04-01
501 46 04-02
501 46 06-01
Application
Starter Spring
For chain saw models: 36R, all 40 series,
44, 45, 140, 165R, 240, 244, 340 and 444.
625-403
501 76 31-01
501 63 02-01
501 63 01-01
654-148
501 62 90-03
Tube Handle
For chain saw model: 242.
.....................................................
654-151
501 87 29-07
For chain saw models:
50, 51, 55 and 254.
.....................................................
501 53 45-02
501 53 45-03
501 80 75-05
705-574
T-Wrench
Fits chain saw model: 32, 36,
38, 40, 44, 50, 51, 55, 61, 66,162,
262, 266, 268, 281, 285, 288, 298,
380, 444, 480, 2100, 2102, 3120 &
most other models. Size: A= 7”,
B= 1”, C= 1”. Bar= 1/2” (13mm),
Plug= 3/4” (19mm)
Starter Spring
For chain saw models: 333,
335, 340, 345, 346, 350, 351,
353 (older style smaller).
Spring is in a metal band, OD= 57mm approximately.
Note: Just because this part is listed for a certain model doesn’t
mean it will fit every saw ever made with that model number.
Please see the image& OEM# to help determine if it is the correct
part for your application.
C
537 09 31-01
For chain saw model: 281.
503 85 99-01
Starter Spring
For chain saw models: 362,
365, 371 and 372. Spring is in
a metal band, OD= 63mm approximately.
Replacement starter spring for our 655-365.
506 25 89-01
Starter Spring
For chain saw models: 340, 345,
346, 350, 351, 353, 357, 359.
(newer style - larger diameter).
Jonsereds chain saw models: 2149, 2159, CS2141,
CS2145, CS2150, CS2152, CS2153, CS2156 and CS2159.
Spring is in a plastic cage, Spring OD = 67mm / 2-5/8”
approximately. Note: Also see our smaller OD spring 625-407.
654-152
503 13 50-01
503 78 72-01
Application
For chain saw models: 61, 66,
162, 266, 266 XP, 268, 268 XP and 272.
.....................................................
Starter Spring
For chain saw models:
356, 394, 395,
3120 and K12506.
625-410
501 52 01-02
654-138
501 70 67-01
Starter Spring
For chain saw models:
older 34 and 35.
(spring in metal band)
625-407
625-411
625-408
Starter Spring
For chain saw models:
42, 133, 154, 242 & 246.
Will also work in models:
254, 257, 261 and 262. (Spring comes in a metal
band and DOES NOT include the plastic case / retainer
625-406
O.E.M
Starter Spring
For Concrete Saw / Cut Quik Saw
models: K750, K760, K960 and K970.
Note: Will work on chain saw models:
340, 345, 346, 350, 351, 357, 359 if you
re-use the original starter spring case - You will have to make a
slight adjustment to the outside spring hook. (This spring is NOT
an exact replacement for the Original Husqvarna# 537 09 31 01)
625-325
Part#
625-430
501 20 13-01
Starter Spring
For chain saw models:
41, 50, 50 Rancher,
51 and 55.
625-405
continued
Starter Spring
For chain saw model: 288
Starter Spring
For chain saw models:
1100, 2100 and 2101.
625-404
Banta
705-592
Carlton# 41C1319T
T Wrench / Scrench
Used on Husqvarna and Stihl
cut quik / cut off / concrete saws.
Fits Husqvarna concrete saw
models: K960 an d K970.
Size: 1/2” (13mm) Bar Nut X
3/4” (19mm) Spark Plug X
(B = 1-3/4”) + (C = 1-1/4”) =
3” total with a 7-3/4” long handle. T27 Torx End.
16-21
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
ICS
JONSEREDS
Part#
O.E.M
605-710
71752
Application
Air Filter
Fits ICS Concrete / Cut off
Saw models: 603GC,
613GC, 633GC and 680GC.
Size: 3-7/8” OD X 2-3/8” ID X 3-1/4” HT.
73336
505375
501 77 85-01
537 07 12-01
Chain Adjuster Assembly
Found on model: 2159 chain saw.
(Includes part#’s 503869101 and 503885401);
73209
570-283
537 15 73-02
2159
Cylinder Assembly (47mm)
Fits model: 2159.
Displacement: 59cc;
Stroke: 34mm.
JONSEREDS
501 80 71-01
501 80 71-05
570-286
Air Filter
For Chain Saw model: 630
605-062
503 70 15-02
651-175
Crankshaft bearing
ICS models 613GC,
633GC and 680GC;
Size: 17mm ID X 40mm OD X 12mm HT.
(Bearing# 6203/C3) Open both sides.
605-173
646-155
Application
Clutch Assembly
Fits chain saw models:
625, 630 and 670.
Measures: 3.057” OD X 0.512” Thick.
(Also see our 646-153 newer style).
Crankshaft Bearing
Fits ICS concrete saws,
Size: 15mm (37/64”) ID X
35mm (1-3/8”) OD X 11mm (7/16”) HT
(Bearing# 6202 - open both sides)
593-103
O.E.M
646-113
Pre Filter
For our 605-710 air filter.
Fits ICS Concrete / Cut off Saw
models: 603GC, 613GC,
633GC and 680GC.
Size: 2-3/8” bottom OD X
2-1/16” top OD X 2-9/16” HT.
592-106
Part#
Clutch Assembly
For chain saw models: 820,
830, 920, 930, 2094 & 2095.
Measures: 3.045” OD (77mm) X
0.542” (13.90mm) Thick.
Same as our 605-709 except higher.
605-711
continued
503 81 45-03
503 69 10-73
503 93 90-03
2065 & 2165
Cylinder Assembly (48mm)
Fits chain saw models:
2065 and 2165.
Air Filter
For chain saw models:
2063, 2071, 2163 and
2171. Nylon mesh style.
Size: 3-5/8” L x 2-7/8” W x 1-5/8” HT
Note: Picture shows front and back views for reference
605-060
537 02 40-03
570-287
Air Filter (Twist on)
For chain saw models:
2141, 2145, 2149, 2150
and 2152. Air filter attaches by simply
twisting on the carburetor manifold.
Note: Some 346 and 353 models use a steel snap to connect.
646-154
503 74 44-01
503 62 64-72
503 62 64-73
503 93 90-05
503 93 93-71
503 93 93-72
503 96 52-71
2071 & 2171
Cylinder Assembly (50mm)
Fits chain saw models:
2071 and 2171.
Clutch Assembly
For chain saw models: 2063, 2065,
2163, 2165, 2071 & 2171.
Measures: 3.057” OD X 0.471” Thick.
C
16-22
C
CHAIN SAW ACCESSORIES - O.E.M
JONSEREDS
Part#
JONSEREDS
continued
O.E.M
572-801
Application
Banta
continued
Part#
O.E.M
572-715
503 60 98-02
503 60 98-03
Application
Piston Assembly (52mm)
Fits chain saw model: 670.
Piston Assembly (44mm)
Fits chain saw model: 2050.
572-705
537 15 72-02
Piston Assembly (47mm)
Fits chain saw model:
2059 and 2159.
572-499
NOTE: For 50mm piston
assembly see our 572-807.
572-717
537 16 98-71
Piston Assembly (54mm)
Fits chain saw model: 2186.
Note: Piston Rings = 1.2mm thick
572-812
503 53 90-02
Piston Assembly (48mm)
For chain saw models:
625 and 630.
Piston Assembly (56mm)
Fits chain saw model: 2094.
Direct replacement for the
original (48mm) bore
Jonsereds cylinder assembly.
572-721
572-714
503 69 13-71
Piston Assembly (48mm)
Fits Chain Saw models:
2065 & 2165.
503 46 02-02
Piston Assembly (56mm)
Fits chain saw model: 2095.
Overall Height = 49mm,
(1mm) higher then our 572-722
Note: Piston rings = 1.5mm thick
572-722
537 13 76-71
(replaces our old# 572-806)
572-524
501 65 94-03
Piston Assembly (56mm)
Fits chain saw model: 2095.
Note: Piston Rings = 1.2mm thick
574-206
Piston Assembly (50mm)
For model: 670.
572-718
503 28 90-42
503 69 12-71
503 69 14-71
503 93 92-71
Piston Assembly (50mm)
Fits Chain Saw models:
2071 and 2171.
572-807
501 65 88-03
Piston Ring Set
(40mm X 1.5mm)
Fits chain saw model: 2040.
574-212
C
503 28 90-05
Piston Ring Set
(42mm X 1.5mm)
Fits chain saw model: 2045.
574-230
503 28 90-29
Piston Ring Set
(47mm X 1.5mm)
Fits chain saw model: 2063 & 2163.
574-157
Piston Assembly (50mm)
Fits chain saw model: 670.
Includes: Piston, Piston pin,
Retainer clips and ring.
503 28 90-02
501 20 56-02
503 28 90-15
Piston Ring only
(48mm X 1.5mm)
Fits chain saw model: 630
For our 572-499 piston assembly.
16-23
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
JONSEREDS
JONSEREDS
continued
Part#
O.E.M
574-137
503 28 90-17
Application
Piston Ring only
(50mm X 1.5mm)
Fits chain saw model: 670
For 572-524 piston assembly
574-254
503 28 90-22
503 71 53-01
503 665 601
503 96 15-01
NOTE: For other Jonsereds “Starter Pulleys”
see our Husqvarna listings for more information
625-400
501 52 04-01
504 21 26-01
504 21 26-02
Starter Spring
For chain saw models:
49SP, 50, 51, 52, 52E & 521EV.
501 56 45-01
625-452
Fuel Cap
For chain saw models:
625, 630 and 670.
504 21 00-17
Starter Spring
For chain saw
models: 451E and 451EV.
503 90 14-01
941 14 60-1
625-455
Electronic Ignition
For chain saw model: 630
504 21 26-06
Starter Spring
For chain saw models: 450, 455,
510SP, 520SP, 525 and 535.
501 51 61-01
501 51 61-02
501 61 75-01
625-325
Electronic Ignition
Fits chain saw models: 625, 630 & 670.
The electronic ignition component is connected with the ignition
coil to achieve full ignition. This type of ignition module utilizes
transistor switches for magnet activation.
C
Starter Pulley
For Chain Saw
model: 361. (Frontier)
Measures: 8mm / .315” ID X 2-3/8” (60mm) OD X
1-1/4” Overall Height. 8 Tooth gear X 1-1/8” OD.
625-451
Gasket Set
Fits chain saw model: 630.
(Includes oil seals)
600-164
(Sold in multiples of 10)
Starter Spring
For chain saw models: 66E,
70E, 80, 90, 111 Super, 621,
801, 910E, 910EV and 920.
640-243
600-185
501 55 14-02
560-147
625-450
Head / Base Gasket only
Fits chain saw models: 362, 365,
372, 372 and 375; also fits
Jonsereds models: 2065, 2071, 2162 and 2171.
551-107
Application
Starter Spring
For chain saw models:
625, 630, Super & 670.
501 51 22-02
Head / Base Gasket
Fits models: 630 and 670.
623-822
363400
Starter Handle
For most Jonsereds
Chain Saw models.
Decompression Valve
(Blue Knob)
For Chain Saw and Concrete saw cylinder assemblies.
Fits Husqvarna, Jonsereds and Partner models: K1250
etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut.
Similar to our 570-003 but with a longer main body.
623-820
610-040
560-191
Decompression Valve
For Chain Saw and Concrete
saw cylinder assemblies.
Overall Length: 1-7/16” - Blue knob with 2 holes in nut.
570-005
O.E.M
Fuel Filter - Felt
Fuel Filter found on many
Jonsereds chain saw models.
Measures: 3/4” L X 1/2” ID X 3/4” OD (Sold in multiples of 10)
Piston Ring Set
(54mm X 1.5mm)
Fits chain saw model: 2083.
570-003
Part#
continued
507 10 00-73
Starter Spring
For chain saw models: M36,
361, 361E, 365, 370 and 380.
16-24
C
CHAIN SAW ACCESSORIES - O.E.M
JONSEREDS
JONSEREDS
continued
Part#
O.E.M
625-426
505 29 51-26
Application
Banta
continued
Part#
O.E.M
636-149
503 71 13-04
Application
Starter Spring
For chain saw models: 490 and 590.
625-404
501 76 31-01
Muffler / Exhaust
For chain saw models: 2094 & 2095. Mounting bolts
holes are on 52mm centres. Note: Complete with spark
Starter Spring
For chain saw model: 2041.
Note: Will work on Husqvarna
chain saw models: 340, 345,
346, 350, 351, 357, 359 if you
re-use the original starter spring case - You will have to make a
slight adjustment to the outside spring hook. (This spring is NOT
an exact replacement for the Original Husqvarna# 537 09 31 01)
625-408
537 10 93-101
Starter Spring
For chain saw models: 2149, 2159,
CS2141, CS2145, CS2150, CS2152,
CS2153, CS2156 and CS2159. Spring is in a plastic cage,
Spring OD = 67mm / 2-5/8” approximately.
636-145
T-Wrench
Fits chain saw models:
510, 525, 530, 535, 630,
670 and most other
Jonsereds models. Size:
A= 7”, B= 1”, C= 1”. Bar= 1/2”
(13mm), Plug= 3/4” (19mm)
705-600
T-Wrench
Fits chain saw models:
77, 90, 621, 820 and 920.
Size: A= 7”, B= 1-1/8”,
C= 1-1/8”. Bar= 19/32”
(15mm), Plug= 3/4” (19mm)
For MAKITA See DOLMAR / MAKITA
This muffler is a NON DF version NOT
US Forest Service approved. (Also see our 636-143)
503 76 53-02
503 76 54-02
McCULLOCH
Muffler / Exhaust
For chain saw models: 2063,
2065, 2071, 2163, 2165 and 2171.
Exhaust mounting holes
are 53mm center to center.
Comes with spark arrester. (Also see our 636-145)
636-148
705-574
503 76 53-01
Muffler / Exhaust
For chain saw models:
2063, 2065, 2071,
2163, 2165 and 2171.
Exhaust mounting
holes are 53mm center to center.
636-143
arrester screen. (Also see our 636-148) Front and back images
shown for reference.
605-204
214224 / 216905
61460 / 91460
Air Filter
Fits models: 110, 120, 130,
Mini Mac and Eager Beaver.
Size: 2” OD X 7/8” HT
503 71 13-07
605-339
213883 / 215803
300385
Air Filter
Fits Chain Saws and Blowers.
Models: 300 and 385.
Felt with rubber seal.
Size: 4” L X 2-13/16” W
Muffler / Exhaust
Fits chain saw models: 2094 & 2095. Mounting bolts holes
are on 52mmcentres. NOTE 1: This muffleris a NON DF version
NOT US Forest Service approved. (Also see our 636-149) Front
and back images shown for reference
C
605-215
89072 / 92410
Air Filter
Fits Chain Saw model: 510
Size: 3-1/4” L X 3-1/4” W
16-25
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
McCULLOCH
Part#
O.E.M
605-253
68685
91458
McCULLOCH
continued
Application
Chain Adjuster
For McCulloch
chain saw model: Mac 6.
605-261
651-243
55498
Air Filter
Fits chain saws models:
D44, 14, 150, 160
and all Super series,
Super 250 & 550.
Size: 5-3/8” L X 5-1/4” W
651-399
(While Quantities Last)
215681
85387
621-120
216685
69922
92420
621-121
610-048
215456
322001
94970
613-601
214226 / 95213
610-238
63932
216985
49422 / 93720
215708
301011 / 64848
Molded Fuel
Line for chain saw model: 10-10.
Measures: 6-1/8” overall length
110676
600-935
Walbro# AM-35
Electronic Module
For chain saw models:
Eager Beaver and
Super Airstream V.
120029
(Original WALBRO module) (Made by SEM / WALBRO)
502-119
213169
Bar Nut
Fits Husqvarna,
(Sold in multiples of 10)
Jonsereds, McCulloch etc.
McCulloch models: 600,
605, 610 and 650.
Size: 8mm X 1.25 thread. For 13mm T-wrench
C
51468A
Fuel Filter - In Tank
Fuel Filter for all McCulloch Mini Chain Saw
and Trimmer models using 3/32” thru 1/8” ID fuel lines.
Measures: 1-1/4” long X 1/2” diameter.
Bar Nut
For chain saw model: Mini Mac 300 series.
Size: 6.3mm X 1.0 thread
670-101
83223
Fuel Filter
Found on many chain saw models.
Made of felt.
Measures: 1” L X 3/4” OD
Bar Nut
For chain saw model: Mini- Mac 600 series.
Size: 1/4”-28
670-105
102115 / 105603
110590 / 110950
91982 / 94362
Clutch Spring
For chain saw models:
Super 250 and Super 550.
Air Filter
Fits chain saws models: 600,
610 series and Eager Beaver 3.7
(Raised centre)
Size: 4-3/8”L X 4-1/4” W
670-104
110907 / 68656
84929 / 90658
Clutch Spring
For chain saw models:
10-10, Mac 7-10, 55, 60 and SP 81.
Air Filter
Fits chain saws models: 310,
320, 330 & Eager Beaver 2.1
Size: 3-3/16” L X 2-11/16” W
605-238
(While Quantities Last)
Chain Adjuster
For chain saw model: 600 series.
Air Filter
Fits chain saws models:
10-10 and 700 series
Size: 4-3/8” L X 4-1/8” W
605-212
Application
Chain Adjuster
For chain saw model:
Mini Mac 100 and 300 series
Air Filter
Fits chain saws models:
800, 805 and 850
Size: 5-3/8” L X 5-1/8” W
605-246
O.E.M
651-141
Air Filter
Fits chain saw model: Power Mac.
Size: 3” L X 2-1/4” W
605-216
Part#
continued
Phelon# 08133-04
Coil and Core (Armature)
For chain saw models: MINI.
For older style with
points & condensor.
(Original PHELON coil)
(Made in the U.S.A.)
16-26
C
CHAIN SAW ACCESSORIES - O.E.M
McCULLOCH
Part#
O.E.M
550-111
89322
Application
Fuel Cap
Gas Cap for chain saw models:
Pro 10-10 and Pro Mac 60 series.
551-111
87270
Oil Cap
For chain saw models:
Pro 10-10 and Pro Mac 60 series.
625-200
51665
Starter Spring
For chain saw models: 1-40, 50,
60, 70, 80, 200, 300, 400, 500,
600, 700, 800, D-44, PM-105,
SP-125, 550 and Super 797.
625-201
OLEO MAC
continued
68626
625-202
83078
Starter Spring
For chain saw models: Mac 110,
115, 120, 130, 140, Mini Mac 6, 25,
30, 35, Power Mac 6, Pro Mac 55,
510, Super Pro 40, 310, 320, 330, 340 & Titan 7.
625-203
83334 / 87680
Starter Spring
For chain saw models: Pro Mac 10-10,
55, 60, 555, 570, 610, 650, 700,
800, 805, 850, 1010S, 5700, 8200,
Super Pro 60, 70, 80, 81 and Model 7-10A.
625-427
32107
continued
Part#
O.E.M
625-500
60 00132
61 00963
Application
Starter Spring
For chain saw models: 260,
261, 271, 272, 284, 460AS,
480AS, 481, 482 and 482 MP.
PARTNER
605-338
506 22 42-01
531 03 14-97
Air Filter
Fits Concrete / Cut-off Saws
models: K650 Active and K700 Active.
Size: 4-3/4” L X 3-3/8” W X 2-1/8” HT.
Note: Top and Bottom images shown for reference.
(For Pre Filter see our 605-239).
605-239
Starter Spring
For chain saw models: Mac 1-10,
2-10, 3-10, 4-10, 5-10E, 6-10,
CP 55, 70, 10-1C and 52-10A.
Banta
506 22 63-01
999810
Pre filter
Fits chain saw models:
K650 Active and K700. (3) layer foam filter
Size: 7-7/8” L X 4-1/2” W X 3/4” HT
605-378
544 18 16-01
Air Filter
Panel Air filter for Concrete /
Cut Quik Saw model: K750.
(For use with our 605-377 pre filter)
Base Size: 4-15/16” L X 4-1/2” W X 1-3/8” HT.
605-377
506 36 71-01
Pre filter
For Concrete / Cut Quik Saw
model: K750.
(For use with our 605-378 air filter)
Size: 7-5/64” L X 5-1/2” W X 13/16” HT.
605-440
Starter Spring
For chain saw model: 1000.
OLEO MAC
625-675
50 00132
Starter Spring
For chain saw models:
250, 251, 251E, 251 Super,
252, 254 and early model 264.
Note: Comes in a plastic case not shown
625-676
40 00132
40 95034
Starter Spring
For chain saw models: 234, 240,
241, 244, 264F - Deluxe, 350, 355A,
935D, 941, 942, 945, 946, 950, 951 & 970.
C
506 23 19-01
506 25 59-32
Pre Filter
(3) Layer foam filter.
Fits chain saw models: K950 Active & K960 Cut Quik saws.
Size: 10-3/8” L X 5-1/4” W X 3/4” HT approx.
(Also see our 605-438 Air Filter)
605-438
506 23 18-01
506 23 18-02
Air Filter
Fits chain saw models:
K950 and K1250
Active Cut Quik saws.
Size: 6” L X 4-1/8” W X 2-5/8” HT
605-280
506 26 87-01
Pre filter
Fits Concrete / Cut Quick Saw
models: K1250.
(3) layer foam filter.
Size: 10-5/32” L X 6-1/2” W X 13/16” HT.
16-27
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
PARTNER
PARTNER
continued
Part#
O.E.M
605-460
505 31 55-30
Application
506 07 05-03
506 29 67-02
544 90 84-02
506 07 05-04
506 34 74-24
503 14 51-01
570-268
506 09 92-12
K650 Cut off
Cylinder Assembly (50mm)
Fits concrete saw models:
K650 (new style),
Super MKII and K700.
570-270
506 38 61-71
K750
506 03 30-31
506 27 67-41
Cylinder Assembly (51mm)
Fits concrete / cut quik
saw model: K750.
506 07 05-06
Drive belt (cogged)
For concrete / cut quick saw
model: K650 Active III & K700 Active III cut off saws.
Size: 3/8” W X 31-1/2” L
875-726
505 29 31-66
Clutch Spring
For models: 281, 288, 3120, 334T, 335XP,
336, 338, 339, 385, 390, 394, 395, K960 and K1250.
Overall Length: 1-1/8” X 7/16” OD.
Drive belt (cogged)
For concrete / cut quick saw
model: K650 Active, K650 Active II and K700 Active II
Size: 1/4” W X 31-1/2” L
875-713
294112
621-115
Drive belt (cogged)
For concrete / cut quick
saw model: K950 Active with 16” blades.
Size: 3/8” W X 36” L
875-711
621-127
Application
Clutch Spring
For chain saw models:
400, 500 and 5000.
Drive belt (multi rib)
For concrete / cut quick
saw model: K750.
Size: .551” W X 32” L (6 rib, polyester cord construction)
875-725
O.E.M
621-156
Drive belt (cogged)
For concrete / cut quick saw
model: K950 with 12” and 14” blades.
Size: 3/8” W X 34-1/2” L
875-712
Part#
Clutch Spring
For chain saw model: R16.
Air Filter
For concrete / cut quik saws.
For models: K1200
and K1200 Mark II.
Size: 5-7/8” OD X 4-1/8” ID X 2-1/2” HT
875-724
continued
570-271
506 15 55-06
K950
Cylinder Assembly (56 mm)
Fits concrete / cut quik
saw model: K950.
506 07 05-07
Drive belt (cogged)
For concrete / cut quick
saw model: K1250 Active cut off saws.
Size: 3/8” W X 39-1/2” L
670-101
503 22 00-01
570-269
Bar Nut
Fits chain saw models:
(Sold in multiples of 10)
R16, S50, S55, P55, P70 and P100.
Size: 8mm X 1.25 thread. For 13mm T-wrench
651-142
506 29 427-1A
K1250
Cylinder Assembly (60mm)
Fits concrete / cut quik saw
model: K1250
230902
267650
Chain Adjuster
For chain saw models:
R16, S50, S55, P55, S65, P70 and P100.
C
16-28
C
CHAIN SAW ACCESSORIES - O.E.M
PARTNER
Part#
O.E.M
572-463
505 34 07-82
Piston Assembly (48mm)
For chain saw model: P650
and Partner concrete saw
model: K650 (old style).
Includes: domed piston and
rings, piston pin and clips.
572-511
PARTNER
continued
Application
Part#
Banta
continued
O.E.M
640-182
Gasket Set
Fits Chain Saw
model: K-650 Active
(While Quantities Last)
640-186
506 09 90-01
Piston Assembly (50mm)
For concrete saw model:
K650 (new style).
Gasket Set
Fits Husqvarna / Partner
cut quit / concrete saw
model: K950. (Includes oil seals).
572-902
640-323
Gasket Set
For chain saw models:
500, 5000 and 5000 Plus.
Piston Assembly (51mm)
Fits concrete / cut quik saw
model: K750.
574-157
(Includes oil seals).
623-868
505 26 60-48
Piston Ring (48mm)
For chain saw model: P650
and Partner concrete
saw model: K650 (old style)
574-137
623-751
503 28 90-17
506 37 67-01
Head / Base Gasket
For cut quik / concrete saw
models: K750 and K760.
503 66 56-01
503 71 53-01
623-499
Decompression Valve
For Chain Saw and Concrete saw
cylinder assemblies. Fits models: K650 and K700, Active I,
II, III. Overall Length: 2” - Black knob with 1 holes in nut.
Similar to our 570-004 but with different knob. (For plug only see
our 570-001)
570-005
503 49 10-02
503 49 10-01
Head / Base Gasket
Fits Chain Saw model P650 and Concrete Saw model
K-650 (both old and new), K700 Active I, II, III.
Piston Ring (50mm)
For Partner concrete
saw model: K650 (newer style).
570-002
Application
503 66 56-01
506 15 82-01
Head / Base Gasket
For cut quik / concrete
saw models: K950.
591-101
302333
Bearing - Piston
Fits Chain Saw models R16, S50,
P650 and Partner K650 concrete saw.
(Size: 12mm X 16mm X 13mm)
551-116
Decompression Valve
(Blue Knob)
For Chain Saw and Concrete saw cylinder assemblies.
Fits Husqvarna, Jonsereds and Partner models: K1250
etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut.
Similar to our 570-003 but with a longer main body.
640-360
506 38 53-05
Gasket Set
Fits Husqvarna / Partner
cut quit / concrete saw
models: K750 and K760.
(Includes oil seals)
C
Oil Cap
For chain saw models:
R16, S50, S55, P55 and P70.
Made of aluminum with screwdriver slot on top.
550-109
506 25 59-32
Fuel Cap
For chain saw and
concrete / cut quik saw
models: K650 and K950.
650-122
340722
Sprocket Cover Partner
Cover for chain saw models:
R16, S50, S55, P55 and P70.
Cast aluminum cover (yellow)
16-29
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
PARTNER
POULAN
continued
Part#
O.E.M
625-426
505 29 51-26
Application
505 29 51-08
295108
504 35 27-05
506 25 89-01
646-129
506 38 56-12
POULAN
23791
530 023791
Air Filter
Fits chain saw models:
Micro XXV, Micro 25, 180, 200, 205, 225, 235,
236, 1800, 2000, 2100, 2300, 2350 and 2400.
Size: 2-5/8” L X 1-1/2” W X 1” HT
605-436
23369
530 023369
605-410
2586
530 002586
530 02586
Air Filter
Fits chain saw model: 361
Size: 4-1/8” L X 3-1/2” W
C
24548 / 20913
530 024548
952 014129
93919
Clutch
For many small Poulan
chain saw and Poulan /
Weedeater Trimmer models.
Measures: 2-3/8” OD, steel washer included.
621-132
Clutch Spring
For chain saw models:
201, 221, 361, 401 and 451.
651-150
530 015134
530 015135
530 023492
Chain Adjuster
For chain saw models: Micro XXV, Micro XXV Deluxe,
Micro 25, Micro 25 Deluxe, 1800 2000, 2300 and 2350.
651-151
15134 / 15135 / 23492
530 015134
530 023492
Chain Adjuster
For chain saw model: 250.
651-375
Air Filter
Fits chain saw models: 25 and 25DA
Size: 3-3/8” L X 1-5/8” W X 1-1/4” HT
036141
530 036141
545 057701
Air Filter
Fits chain saw models:
3400 and 3700.
Size: 3-7/8” L X 2-5/8” W X 1” HT
Starter Assembly
For concrete / cut quik saw model: K750. This aftermarket
assembly comes complete with housing, starter pulley,
spring, rope, handle etc. Just needs to be bolted on
605-428
530 037793
605-402
Starter Spring
For Partner / Husqvarna
Concrete Saw / Cut Quik Saw models:
K750, K760, K960 and K970.
655-250
605-515
Application
Air Filter
Fits chain saw models: 2200, 2500,
2600, 2700, 2750, 2775, 2900, 3050, PP4620AVHD,
PP4620AVL and Poulan Pro 255, 295, 310 and 315.
Size: 3” L X 2-3/4” W X 7/8” HT
Starter Spring
For chain saw models:
MINI P, P2, 3, 4, 330,
340, 350, P11 and P12.
625-430
O.E.M
605-486
Starter Spring
For chain saw models: R16, 18,
22, 30, 40, F55, K16, 20, 65,
650, 850, 1200, P55, 70, 100, 7000.
625-325
Part#
Air Filter
Fits chain saw models:
1950, 2050, 2075, 210, 2150, 2175,
2250, 230, 2450, 2550, 260, Pro 221, 221LE, 2375,
Wild Thing, 1900, 2350, 2055, 220, 225 and Woodsman.
Size: 3-1/4” L X 2-1/2” W X 3/4” HT
Starter Spring
For chain saw models:
500, 5000 and 5000 Plus.
625-427
continued
(While Quantities Last)
15385 / 23064
530 015385
530 023064
Chain Adjuster
For chain saw models: 3400 and 3700.
651-377
069611
530 069611
Chain Adjuster
For chain saw models: 210, 230, 260,
2050, 2075, 2150, 2175, 2250, 2450 and 2550.
16-30
C
CHAIN SAW ACCESSORIES - O.E.M
POULAN
Part#
POULAN
continued
O.E.M
Application
570-130
23364
530 091878
Fuel Filter
Replacement felt filter for our
(Sold in multiples of 10)
610-014 in-tank fuel filter.
Fuel Filter for many Poulan chain saw models.
Measures: 1” Long X 1/4” ID X 9/16” OD.
34032
530 034032
Fuel Filter
Replacement felt filter for our
(Sold in multiples of 10)
610-006 in-tank fuel filter.
Fuel Filter for many Poulan chain saw models.
Measures: 1” Long X 7/16” ID X 13/16” OD.
610-345
530 023166
530 026119
Duck Bill Valve
For Homelite chain saw models XL, XL-2 and Super 2.
Duck Bill Valve - Fits Homelite Trimmers and Chain Saws.
Measures: .100” ID X .201” OD X .25” L
125-245
530 014347 / 952 701583
530 010729 / 952 701567
Gas Cap
For chain saw models: 180, 190,
1800, 185, 2000, 2300AV, 2300CVA, 2350CVA and 5500.
Measures: 1-1/2” diameter.
550-151
530 071266
501 819602
Fuel Cap
For chain saw models:
234, 238 and 365.
600-915
Walbro#MA-15
Electronic Ignition Module
For Poulan / Weedeater
chain saw “CSI” models.
(Original WALBRO / SEM module)
C
Part#
O.E.M
630-038
2501
560-101
Includes: cylinder,
piston and rings, piston pin & clips. (Cylinder Bore: 41 mm).
This cylinder kit seems to be listed as fitting several Poulan
chain saw models varying from 33 cc thru 42 cc. Please
see picture for more clarification. Dealers have told us this
kit replaces Poulan OEM#’s 530069606 and 530047127.
610-030
continued
Application
Starter Cup
For chain saw model: 25D.
Made of aluminum
Cylinder Assembly
Fits chain saw models: 220,
221, 260, 351, 370, 390, 420,
1950, 2050, 2150, 2175, 2250,
2375 Wild Thing, 2450, 2550.
610-022
Banta
4229
Starter Dog / Starter Pawl.
Found on many older chain
saws using an aluminum starter cup.
Size: Dog width: 1/2” with a 3/8” ID.
610-034
530 023877
Fuel Line Fitting
Fits chain saw models: 180, 1800, 180C, 1800 Super,
190, 2000, 210, Micro XXV and S23. Arbor Pro gas saws.
610-032
530 010897 / 530 014362
530 014815 / 530 023364
530 047004
530 095643
530 095646
530 095649
Fuel Filter
Fits chain saw models: 2025, 2050, 2350, 2775 & FL 1500.
Size: 9/16” OD X 1-5/8” L.
660-060
530 069957
530 071259
Oil Pump
Fits chain saw models:
1950 thru 2550, 211, 220 & 260 Pro.
560-368
530 069313
69313
Starter Pulley
Fits chain saw models:
2200, 2500, 255, 2600, 2750,
2900, 295, 3050, 310, 315.
Starter Pulley for Poulan saws - Dealers have used it on
Husqvarna model 41 Chain Saw. May fit other Husky
saws? (4) cog pulley.
NOTE: original Husky application is (6) cog.
145-516
Starter Rope Assembly
For chain saw models:
25D and also 180 and 190.
Rope length 21”, plastic
knob fastened to rope end.
625-152
530 042012
42012
Starter Spring
For chain saw models:
245, 305, 306, 345, 2000 and 2300
16-31
C
Banta
CHAIN SAW ACCESSORIES - O.E.M
POULAN
REMINGTON
continued
Part#
O.E.M
625-442
530 027531
Application
530 042051
42051
4262
605-914
67863
625-157
080604
Air Filter
Fits chain saws. Made of wire mesh and felt material.
Size: 2-3/4” L X 7/8” W
66241
65071
SHINDAIWA
625-900
60832
Starter Dog / Starter Pawl.
Found on many older Remington
chain saws using an aluminum
starter cup. Used on older Poulan, Homelite, Remington
and Stihl chain saws. Remington models: Pl-4, Sl-4A,
Bantam etc. Size: Dog width: 1/2” with a 3/8” ID.
C
42051
38010-82581
Air filter
Fits Cut off saws, models:
EC7500 and EC7600.
(includes foam pre filter)
Size: 7” L X 4” W X 2” HT
Air Filter
Fits chain saw model:
SL9 and SL9 deluxe.
Made of felt material.
Size: 3-5/8” L X 3-5/8” W.
560-101
643A128
9918R
Starter Spring
For chain saw models:
358-354810, 358-354830
(3.4, 3.7 CU. IN. Poulan)
605-319
Air Filter
Fits chain saw model:
Mighty Mite (Large version).
Made of felt material.
Size: 3-9/16” L X 3-1/4” to 4-1/16” W (bottom)
605-553
9163H
Air Filter
Fits chain saws.
Size: 4-1/4” L X 2-1/2” W
Air Filter
Fits chain saws.
Made of wire mesh and felt material.
Size: 1-13/16” L X 1-3/16” W
605-523
SEARS / ROPER / AYP
Air Filter
Fits AYP / Sears/ Roper Chain Saw.
Sears model 3.7 cubic inch
Size: 3-7/8” L X 3-5/8” W
REMINGTON
605-533
FOR SACHS DOLMAR
- SEE “DOLMAR /
MAKITA” SECTION.
605-907
Starter Spring
For Lombard chain saw
models: 42 series,
Lightning and Comango.
Starter Spring for Poulan chain
saw models: 360, 361 and 400.
605-501
Application
(Sold in multiples of 10)
Starter Dog Washer
This is a fibre washer used
on older Fairbanks Morse,
Remington etc. chain saws that used a
starter dog assembly and aluminum starter cup.
Starter Spring
For chain saw models:
3400 and 3700.
Starter Spring for Sears / Roper / AYP chain saw
models: 358-354810, 358-354830 (3.4, 3.7 CU. IN. Poulan)
625-101
O.E.M
560-102
Starter Spring
For chain saw models:
2025, 2050, 2075, 210, 2150, 2175,
2250, 230, 2350, 2450, 2550 and
260, 285, 295, 305, 310, 315 and 335
625-157
Part#
continued
22104-75300
22104-75310
Starter Spring
For chain saw models: 305, 345,
346, 350, 355, 405, 406, 407, 410, 415,
416,440, 450, 451, 480, 485 and 500.
625-901
22100-75310
Starter Spring
For chain saw models:
415 and 450 (older models)
16-32
C
CHAIN SAW ACCESSORIES - O.E.M
SKIL
STIHL
Part#
O.E.M
625-325
F315882
Application
Starter Spring
For chain saw models:
1600 and 1616.
625-427
295108
Banta
continued
Part#
O.E.M
605-679
1127-120-1621
11127-120-1620
Application
Air Filter
Fits chain saw models:
029, MS290, MS310
and MS390.
Size: 4-9/16” L X 2-5/8” W X 1-1/2” HT.
(Top and Bottom pictures shown (1) air filter only)
Starter Spring
For chain saw models:
1632 and 1646.
SOLO
625-826
(Homelite 47/54)
26 00 166
Starter Spring
For chain saw models:
610, 611, 616, 647 and 654.
(Fits HOMELITE Saw models 47 and 54)
625-828
26 00 167
Starter Spring
For chain saw models:
635 and 642.
STIHL
605-708
1108-120-1600
Air Filter
Fits chain saw
models: 08 and 08S
541-103
1108-140-1000
Air filter cap
Fits chain saw models:
08 and 08S.
(For use with our 605-708 air filter)
605-719
1120-120-1600
1120-124-0800
Air filter
Fits chain saw model: 009, 010, 011.
Size: 3-7/8” L X 2-5/8” W
605-717
1130-124-0800
Plate filter
Fits chain saw models:
017, 018, MS170 and MS180.
Size: 3-1/2” L X 2-9/16” W approximately.
605-687
1123-120-1613
1123-120-1612
605-741
Air Filter
Fits chain saw models:
026 and MS260.
(Top and Bottom pictures shown (1) air filter only)
605-733
C
1118-120-1610
1118-120-1611
1118-120-1615
Air Filter
Fits chain saw models:
028, 028 Super and 028 Wood Boss.
Size: 3-1/2” L X 2-1/4” W X 3/4” HT
605-753
1125-120-1615
1125-120-1620
Air Filter
Fits older Stihl models:
034, 034 Super and 036.
Fits older 034 chainsaws before
Serial Number 1 45 945 205.
Fits older 036 chainsaws before serial number X 32 622 639.
This filter doesn’t have the compensator hole, and is too narrow
for newer models 034 & 036. Please verify serial number first
before purchasing. Size: 3-1/4” L X 2-7/8” W X 1-1/8” HT
606-138
1119-140-1903
1119-140-1905
Air filter cover
Aftermarket box cover
for chainsaw model 038 series.
This plastic piece often takes most
of abuse from day to day use and fades in colour.
Includes attachment nut and mesh screen.
605-071
1119-120-1610
1119-120-1611
1119-120-1615
Air Filter
Fits chain saw models:
038, 038 Super, Magnum and Wood Boss.
Size: 4-1/8” L X 3-1/8” W X 7/8” HT
605-675
Air Filter
Fits Chain Saw models:
MS210, MS230 and MS250.
Size: 3-5/8” L X 1-3/16” W X 1-3/8” HT.
1121-120-1617
1110-120-1601
Air Filter
Fits chain saw model: 041.
Made of wire mesh & felt material.
Size: 4-1/4” L X 4-1/8” W
16-33
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
541-106
1110-140-9500
Application
Air filter cap
Fits chain saw models:
041, 051 and 070.
(For use with our 605-675 / 605-676 / 605-686 air filters)
605-676
1111-120-1601
Air Filter
Fits chain saw models:
051 and 076.
Made of wire mesh and felt material.
Size: 5” L X 4-1/4” W
605-683
1120-120-1610
605-709
4201-140-1805
4201-141-0300
0000-120-1653 / 0000-120-1654
Air Filter
Fits chain saw models: 044, 046, 064, 066, 088, MS440,
MS441, MS460, MS640, MS650, MS660 and MS880.
Felt cloth outer wrap with a foam filled interior. Designed
for oil-less use. Size: 4-3/16” L X 3-1/8” W X 1-3/4” HT
1122-120-1615
1122-120-1620
605-686
605-725
4223-140-0300
4223-140-1800
Air Filter
Fits Concrete / Cut off Saw
model: TS400 (secondary filter).
Size: 4-5/8” L X 2-11/16” W X
Pipe: 1-1/8” OD X 7/8” HT
(While Quantities Last)
605-337
4223-141-0600
4201-140-1801
Air Filter
Fits Concrete / Cut off Saw
models: TS350 and
old style TS510 / TS760
Inner filter - 2 bolt mount style (Inner filter for our 605-709)
C
4223-141-0300
(While Quantities Last)
1106-120-1602
Air Filter
Fits chain saw model:
070. Made of wire mesh
and felt material.
Size: 6-3/8” L X 4-1/8” W X 1/8” HT
4201-140-1802
Air Filter
Fits Concrete / Cut off
Saw model: TS400 (air
filter). Size: 5-3/8” L X
3-3/8” W X 1-15/16” HT.
(Paper element with soft foam seal)
605-332
Air Filter
Fits chain saw model:
064 (older style)
Nylon mesh material
4201-141-0310
Inner Air Filter
Fits Concrete / Cut off Saw
model: TS360.
Inner filter - centre bolt mount style.
(Inner filter for our 605-709)
605-336
605-764
Application
Air Filter
Fits Concrete / Cut off Saw
models: TS350, TS350AVE,
TS360, TS510 and TS760.
Size: 3-7/8” OD X 2-3/8” ID X 2-7/8” HT
(Also found on Sachs Cut off saws)
605-055
Air Filter
Fits chain saw models:
044 and 046 (older style)
Nylon mesh material
(Orange in colour)
605-735
O.E.M
Air Filter Wrap
Fits Concrete / Cut off Saw
models: TS350, TS360
and TS510 / TS760. Felt wrap with
stitched elastic for tight seal. (Pre filter for our 605-709)
Air Filter
Fits chain saw models: 031 and 032.
Size: 3-1/8” L X 2-5/8” W X 15/16” HT
605-744
Part#
605-691
1113-120-1602
1113-120-1603
1113-120-1612
continued
Air Filter
Fits Concrete / Cut off Saw
model: TS400 (pre filter).
Size: 5” L X 3-1/8” W X 13/16” HT, Centre
hole 5/16”, Offset hole 3/16” ID. (3) layer foam
16-34
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
605-348
4221-140-4400
4221-141-0300
Application
continued
O.E.M
Application
Air Filter Kit for STIHL TS360
605-810
Air Filter
Fits Stihl Concrete / Cut
off Saw models: TS460 /
TS510 / TS760 (air filter).
Size: 4-1/2” OD X 2-1/16” ID X 2-1/4” HT.
4201-140-1801
4201-140-1802
4201-141-0310
Air Filter (3) Piece Kit
Fits Stihl Concrete / Cut off Saw
model: TS360
(Use with our 605-343 & 605-346)
605-343
Part#
Banta
4221-140-1800
Air Filter Kit for TS400
Air Filter
Fits Stihl Concrete / Cut off Saw
models: TS460 /
TS510 / TS760 (inner filter).
Size: 1-7/8” OD X 1-11/16” ID X 1-11/16” HT.
605-820
4223-007-1010
4223-140-1800
4223-141-0300
4223-141-0600
(Use with our 605-348 and 605-346)
605-346
4221-141-0310
Air Filter (3) Piece Kit
Fits Stihl Concrete / Cut off Saw model: TS400. Kit
includes: (1) 605-336, (1) 605-332 and (1) 605-337
Air Filter
Fits Stihl Concrete / Cut off Saw
models: TS460 /
TS510 / TS760 (pre filter).
Made of felt material.
(Use with our 605-348 and 605-343)
605-692
Filter Kit for TS460, TS760
605-840
4224-141-0300
4224-141-0300A
Air Filter
Fits Concrete / Cut off Saw
models: TS700 and TS800.
Size: 5-1/2” L X 4-1/16” W X 1-3/4” HT.
(Paper element with soft foam seal). Uses our 605-700 pre filter.
605-700
Air Filter (3) Piece Kit
Fits Concrete / Cut off Saw
models: TS460 / TS760
Filter kit for TS410 and TS420
4224-140-1801
605-850
Air Filter
Pre Filter (secondary filter)
Fits Concrete / Cut off Saw
models: TS700 and TS800.
Size: 4-5/8” L X 3-1/4” W X 9/32” HT.
For use with our 605-692 air filter.
Filter Kit for TS350 & TS510
605-800
4201-140-1801
4201-140-1805
4201-141-0300
4201-141-0310
Air Filter (3) Piece Kit
Fits Concrete / Cut off Saw
models: TS350 and TS510
C
4221-007-1002
4221-140-1800
4221-140-4400
4221-141-0310
4238-140-1800
4238-140-4401
4238-140-4402
4238-141-0300
4238-141-300B
Air Filter (2) Piece Kit
Fits Concrete / Cut off Saw
models: TS410 / TS420.
(Includes (1) 605-559 pre filter and panel filter).
The panel filter measures:
5-3/4” L X 5-1/2” W X 1-3/4” HT approximately.
605-559
4238-140-1800
Air Filter
Fits Stihl Concrete / Cut off Saw
models: TS-410 and TS-420.
Size: 5-5/16” L X 3-3/16” W.
(For 2 pc kit - “pre filter and panel filter”, see part# 605-850)
16-35
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
657-134
1118-790-9930
Application
Av Buffer
Anti Vibration Damping
For chain saw models: 028 and 038.
Size: Steel plate: 1-11/16” Long X 1-3/16” Wide,
with (2) 3/16” holes
657-143
1125-790-9906
1121-790-9906
1121-790-9909
1121-790-9911
1121-790-9912
1111-790-9915
1111-790-9900
657-084
1128-790-9900
Av Buffer
Anti Vibration Damping;
Tank / Annular Buffer for chain saw
models: 044, 046, MS440, and 460.
(Two pictures shown for reference)
4224-790-9900
Av Buffer
Anti Vibration Damping /
Annular buffer for Concrete /
Cut off / Cut quik saw model: TS700.
4221-792-9300
Av Buffer
Anti Vibration Damping /
Rubber buffer for Concrete /
Cut off / Cut quik saw models: TS460, TS700 and TS800.
Measures: 1-5/8” Long X 1-3/16” Wide X 5/8” Overall HT.
(Two images shown for reference)
670-101
9220-260-1100
Bar Nut
(Sold in multiples of 10)
Fits chain saw models:
010, 015, 020, 028 (old), 031, 032, 041, 042, 045, 056 etc.
Size: 8mm X 1.25 thread. For 13mm T-wrench
Av Buffer
Fits chain saw models:
051, 076 and TS510. Use on back handle.
Size: 1-3/8” OD with 5/16” ID hole in the steel end.
657-532
1123-791-2805
Av Buffer
For chain saw models:
021, 023, 025, 029, 039,
MS210, MS230, MS250, MS290 and MS390.
Size: 23mm OD X 8mm ID X 30mm overall length
657-086
Av Buffer
For chain saw models: 015AV, 051, 076
and TS510. Use on front handle, lower damper.
Size: 1-11/16” OD with 25/32” ID hole in the steel end.
657-140
1123-790-9900
Application
(Two images shown for reference)
1111-790-9905
Av Buffer
For chain saw models: 015AV, 051,
076 and TS510. Use on front handle, upper damper.
Size: 1-1/4” OD with a 5/16” ID hole in the steel end.
657-010
657-082
657-085
Av Buffer
Anti Vibration Damping for chain saw
models: 024, 026, 038 & 088.
Size: 1” OD (steel washer end) X 1-1/8” OD (rubber end)
with a 3/8” ID in rubber end. Overall height: 1-1/16”
657-009
O.E.M
657-083
Anti Vibration Damping
For chain saw models: 024, 026, 028 and 038.
Size: 15/16” OD (steel washer end) X 1-5/16” OD (rubber
end) with a taper to 11/16” ID in rubber end.
Overall height: 1-1/16”
657-135
Part#
Anti Vibration Damping
For chain saw models: 021, 023,
025, MS210, MS230 and MS250.
Size: 22mm (top) / 25mm (bottom) X
11mm ID X 30mm overall length
AV Buffer
For chain saw models: 034, 036, 044, 046,
064, 066, MS340, MS360, MS440, MS460, MS640 and
MS660 also fits concrete saw / cut quik saw model: TS400.
Size: 34mm” Bottom OD X 28mm Top OD
with 6mm ID hole in the end. Overall HT: 27mm
657-136
continued
670-114
0000-955-0801
1120-790-9600
(Sold in multiples of 10)
Av Buffer
For chain saw models:
010, 011, 012 AV and 019T.
657-081
(While Quantities Last)
1123-791-2800
Av Buffer
For chain saw models:
MS170, MS180, MS270 and MS280.
Size: 22mm (top recessed) / 25mm (bottom) X
11mm ID (recessed at the top) X 30mm overall length
C
Bar Nuts
Bar nuts for Chain Saw models: 021, 023, 025,
026, 028 series, 038 Super series, 044, 064 etc.
Size: 8mm X 1.25 thread
653-122
Bar Plate Set
Bar Plates for chain saw
model: 08S (newer style)
16-36
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
653-113
1111-664-1000
1111-664-1005
Application
9490-000-7840
9490-000-7850
651-155
651-157
9490-000-7900
651-159
9490-000-7891
9490-000-7892
651-158
For other Carburetor parts - see our
“Carburetor Kits & Parts” section
Clamping Collar
For our 606-414 elbow.
Fit chain saw model: 038 series.
1119-141-2200
Carburetor Rubber Elbow
Intake Manifold - Rubber
Fits 038 series chain saw.
1125-141-2200
Carburetor Rubber Elbow
Intake Manifold - Rubber. Fits chain saw
models: 034, 036 and MS360.
C
1123-640-1900
1123-664-1400
Chain Adjuster
For chain saw models:
MS210, MS230 and MS250.
1110-129-1200
9771-021-2580
0000-951-2911
1106-644-1500
1106-644-1501
1106-664-1501
Chain Adjuster
For chain saw models: 08S, 08 Super, 050, 051, 070, 075 & 090.
Intake Gasket
For chain saw model: 041.
606-412
1110-664-1500
1110-664-1600
Chain Adjuster
For chain saw models: 030, 031,
032, 041, 042, 045, 048 and 056 series.
Drive belt (cogged)
For concrete / cut off saw models:
TS510 and TS760 with 14” blade
Size: 3/8” W X 36.3” L.
606-414
1118-664-1600
1120-664-1500
9490-000-7901
(Type 6) MULTI RIBBED
606-776
1118-182-0900
Chain Adjuster
For chain saw models: 009, 028 and 038 series (old style)
Drive belt (multi ribbed)
For concrete / cut off saw
models: TS420.
Size: 7/16” W X 32” L.
623-279
1122-141-2201
Application
9490-000-7851
(Type 6) MULTI RIBBED
875-3822
606-418
651-152
Drive belt (multi ribbed)
For concrete / cut off saw
models: TS410.
Size: 1/2” W X 29-1/2” L.
875-3821
O.E.M
Control Shaft
Fits 028 series chain saws.
Drive belt (cogged)
For concrete / cut off saw model:
TS400.
Size: 3/8” W X 34-7/16” L
875-3820
Part#
606-775
Drive belt (cogged)
For Cut Quik models:
TS350, TS360 and TS460.
Size: 3/8” W X 33-3/4” L
875-273
continued
Carburetor Rubber Elbow
Intake Manifold - Rubber.
Fits chain saw models: 066 and MS660.
Bar Plate Set
For chain saw models:
050, 051 and 075.
875-272
Banta
1122-664-2200
1122-664-4500
1125-007-1021
1125-640-1900
9646-945-0490
Chain Adjuster Kit
For chain saw models: 024, 026, 034, 035,
044, 046, 220, MS240, MS260, MS270, MS340, MS341,
MS360, MS362, MS440, MS441, MS460, MS640, MS660.
Includes: Tension Slide (1125-640-1900), Spur Gear, Adjusting
Screw, Rubber O-ring 7X1.5 NOT shown in picture (9646-9450490), Cover plate (1122-664-2200, Support (1122-664-4500).
646-112
1121-160-2051
Clutch Assembly
For chain saw models:
026 and MS260.
(Washer plate included as shown in picture).
Measures: 2.675” OD X 0.403” Thick.
19mm nut attached to this clutch for removal.
16-37
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
646-114
1127-160-2051
Application
Clutch Assembly
For chain saw models:
029 and 039.
continued
Part#
O.E.M
621-138
0000-997-5425
Clutch Spring
For chain saw model: 028 (old).
Measures: 5-7/8” overall length.
0000-997-5811
(Washer plate included as shown in picture).
621-137
Measures: 2.928” OD X 0.403” Thick.
19mm nut attached to this clutch for removal.
Clutch Spring
Fits chain saw models:
028 (new), 031, 041, 08 and 08S.
Size: 15/16” overall length.
646-116
1108-160-2002
Clutch Assembly
For chain saw model:
08S and Cut Quik models:
TS350 and TS360.
Measures: 2-19/32” OD X 1/2” ID X 3/16” keyway
646-120
1119-160-2000
Clutch Assembly
For chain saw
model: 038 series.
Measures: 2-3/4” OD X 9/16” ID - 5/8” Overall HT.
646-117
1125-165-2052
Clutch Assembly
For chain saw
models: 036 / MS360.
Measures: 2.894” OD X 0.390” Thick.
19mm nut attached to this clutch for removal.
646-123
1125-160-2006
Clutch Assembly
For concrete / cut quik saw
model: TS400.
Measures: 2.885” OD
646-119
1122-160-2005
Clutch Assembly
For chain saw models:
064, 066, MS640 and MS660.
Application
621-141
0000-997-6002
Clutch Spring
For chain saw models: 051 and 075.
Size: 1-1/4” length.
621-159
(Sold in multiples of 3)
0000-997-0911
Clutch Spring
Fits Stihl chain saw models:
064, 066, MS640 and MS660.
Size: 7/8” overall length
570-281
(Sold in multiples of 3)
000-997-0907
Clutch Spring
Fits chain saw models: 038, MS380.
Size: 13/16” overall length
621-160
(Sold in multiples of 3)
0000-997-0909
Clutch Spring
Fits chain saw models: 029,
034, 036, MS 290, 340, 360, 390.
Size: 7/8” overall length
621-152
(Sold in multiples of 3)
1121-020-1208
1121-020-1209
(Sold in multiples of 3)
026 / MS260
Cylinder Assy (44mm)
Fits chain saw
models: 026 / MS260.
(Washer plate included as shown in picture).
Measures: 3.140” OD X 0.460” Thick.
19mm nut attached to this clutch for removal.
646-124
1128-160-2004
Clutch Assembly
For chain saw
models: 044, 046, MS440,
MS460, also fits MS341 & MS361.
(Washer plate included as shown in picture).
Measures: 2.916” OD X 0.392” Thick.
19mm nut attached to this clutch for removal.
621-135
0000-997-5625
570-205
1121-020-1217
026 / MS260
Cylinder Assy (44.7 mm)
Fits chain saw
models:
026 / MS260.
Note: With serial numbers
after 2 62 187 362
See our website.
Clutch Spring
For chain saw models: 015 & 024 (old style).
Measures: 5-3/4” overall length.
C
16-38
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
570-159
1110-020-1201
Application
041
Cylinder Assy (44 mm)
Fits chain saw
model: 041.
570-216
1118-020-1202
Banta
continued
Part#
O.E.M
Application
570-251
1125-020-1206
1125-020-1209
1125-020-1213
1125-020-1215
034 Super
036 & MS360
Cylinder Assy (48mm)
Fits chain saw models:
034 Super, 036 & MS360.
028 Super
Cylinder Assy (46mm)
Fits chain saw
model: 028 Super.
This cylinder will replace
the following Stihl#’s
1125-020-1206, 1125-020-1209
& 1125-020-1213.
NOTE: On older 034 saw
(46mm) slight modification is
required. Instructions are enclosed. This upgrade will increase
your older 034 from 56.5cc to 61.5cc. (Replaces our 570-250)
570-278
4221-020-1201
TS460
Cylinder Assy (48mm)
Fits Cut Quik Saw
model: TS460.
570-155
1108-020-1220
TS-350 Cut Quik
Cylinder Assy (47mm)
Fits Cut Quik Saw
model: TS-350.
(Also fits 08 &
08S Chain Saws)
570-194
1135-020-1202
Note: This cylinder assembly
has the threaded hole beside the
spark plug for a decompressor.
Note: Decompression valve
NOT included.
570-196
MS361
1127-020-1216
039 & MS390
Cylinder Assy (49mm)
Fits Stihl chain saw
models: 039 and MS390
Cylinder Assy (47mm)
Fits chain saw
model: MS361.
Bore: 47 mm,
Stroke: 34 mm,
Displacement: 59 cc,
Rings: 47 mm X 1.2 mm.
570-190
1127-020-1214
1127-020-1215
1127-020-1217
1127-020-1218
570-227
MS310
029 / MS290
TS-360
Cylinder Assy (49mm)
Fits Cut Quik Saw
model: TS-360
Replace your TS-350
with this C & P
for extra power.
570-208
Cylinder Assy (47mm)
Fits Stihl chain saw
models: MS310
& 029 / MS290 - read on.
Give your Stihl 029 /
MS290 (46 mm bore) an
upgrade from 56.5 cc to 59 cc.
This cylinder will also replace the older 029 (45mm bore,
before SN# X 39 305 257) as well. Bore: 47 mm,
4201-020-1200
1119-020-1201
038 Super
Cylinder Assy (50mm)
Fits chain saw
model: 038 Super.
Stroke: 34 mm, Displacement: 59 cc, Rings: 47 mm X 1.5 mm.
C
16-39
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
570-210
1128-020-1227
Application
044 / MS440
Cylinder Assy (50mm)
Fits chain saw
models: 044
(after serial# X 29 382 283)
MS440.
570-209
1138-020-1201
4238-020-1202
MS441 / MS441C
TS410 & TS420
038 Magnum
NOTE: This cylinder is NOT equipped with a De-compression valve
hole. For a cylinder with a Decompression valve hole see our
570-206. (Also see our 623-132, 623-672, 640-238 or 640-272).
1119-020-1204
1128-020-1221
1128-020-1217
046 & MS460
570-162
1111-020-1200
051 / TS-510
570-212
1122-020-1211
066 & MS660
570-200
1128-020-1121
046 / MS460
Cylinder Assy (54mm)
Fits chain saw
models: 046 / MS460
(BIG BORE).
Cylinder Assy (52mm)
Fits chain saw
model: 038 Magnum.
570-206
570-211
Application
Cylinder Assy (54mm)
Fits chain saw models:
066 & MS660.
Decompression valve
NOT included.
Comes with threaded plug only.
Also see our 640-285 Gasket Set.
1119-020-1202
1119-020-1215
O.E.M
Cylinder Assy (52mm)
Fits chain saw
models: 051 and Cut
Quik model TS-510.
Cylinder Assy (50mm)
Fits Cut Quik Saw
models: TS410
and TS420.
570-272
Part#
Cylinder Assy (52mm)
Fits chain saw
models: 046 & MS460.
Cylinder Assy (50mm)
Fits chain saw
model: MS441
and MS441C.
570-276
continued
MS381
Bore: 54 mm, Stroke: 36 mm,
Displacement: 82.5 cc,
Rings: 54 mm X 1.2 mm.
570-204
4224-020-1202
TS700 & TS800
Cylinder Assy (56mm)
Fits Stihl concrete /
cut off saw model:
TS700 and TS800.
Cylinder Assy (52mm)
Fits chain saw
model: MS381.
Note: Decompression valve NOT included, use our 570-004
Decompression valve. Bore: 52 mm, Stroke: 36 mm,
Displacement: 76.5 cc, Rings: 52 mm X 1.5 mm.
C
16-40
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
570-214
4205-020-1200
Application
TS760
Cylinder Assy (58mm)
Fits Stihl concrete / cut off
saw model: TS760.
Banta
continued
Part#
O.E.M
572-599
1121-030-2003
Application
Piston Assembly (44.7mm)
Fits Stihl chain saw
models: 026 and MS260.
NOTE: This piston assembly fits the
newer 026, MS260 Stihl models after serial# 2 62 187 362.
NOTE: For the older 44mm piston assembly see our 572-525.
572-384
572-590
4119-030-2003
Piston Assembly (38mm)
Fits Trimmer models:
FS220 and FS220R.
572-601
1118-030-2001
Piston Assembly (44mm)
Fits Chain Saw models:
028 and 028 Wood Boss
“older style”.
572-255
1110-030-2002
1110-030-2000
1123-030-2001
Piston Assembly (44mm)
Fits Stihl chain saw
model: 041 old style.
Piston Assembly (40mm)
Fits chain saw models: 023.
572-604
1113-030-2001
1121-030-2005
Piston Assembly (42mm)
Fits chain saw
models: 024 / MS240.
572-607
572-699
Piston Assembly (44mm)
Fits Chain Saw model: 031.
572-388
1113-030-2003
1123-030-2003
Piston Assembly (42mm)
Fits Stihl chain saw
models: MS250.
Piston Assembly (45mm)
Fits chain saw model: 032.
Note: For 025 model with larger
42.5mm bore see our
572-603 piston assembly.
572-449
572-603
1123-030-2011
1118-030-2003
Piston Assembly (46mm)
Fits chain saw
model: 028 Super.
Piston Assembly (42.5mm)
Fits chain saw models: 025.
Replacement piston
assembly for our 570-216.
Note: For MS250 model with
smaller 42mm bore see our
572-607 piston assembly.
572-605
572-525
1121-030-2001
1125-030-2002
Piston Assembly (46mm)
Fits chain saw models:
034 / MS340.
Piston Assembly (44mm)
Fits chain saw models:
026 and MS260.
572-602
NOTE: This piston assembly
fits the older 026, MS260 Stihl
models before serial# 2 62 187 362.
They WILL NOT fit the newer MS260 models with the larger
44.67mm bore.
Piston Assembly (47mm)
Fits chain saw model: MS361.
C
1135-030-2000
(ring thickness 1.2)
16-41
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
572-247
1108-030-2020
Application
Piston Assembly (47mm)
Fits chain saw models:
08, 08S, and
Cut Quik model TS-350.
(Replacement piston assembly for our 570-155.)
572-608
1113-030-2001
Piston Assembly (47mm)
Fits Stihl chain saw
models: MS310.
572-497
1125-030-2001
Piston Assembly (48mm)
Fits chain saw models:
034 Super and 036.
572-614
4221-020-1201
Piston Assembly (48mm)
Fits Cut Quik Saw
model: TS460.
Replacement piston assembly for our 570-278.
572-606
1127-030-2005
Piston Assembly (49mm)
Fits chain saw models:
039 / MS390.
572-460
4201-030-2000
Piston Assembly (49mm)
Fits Cut Quik model: TS-360.
Replacement piston assembly for our 570-227
572-521
4223-030-2000
Part#
O.E.M
572-609
1128-030-2000
Replacement piston assembly for our 570-277
572-441
1119-030-2001
572-610
(Replacement piston assembly for our 570-208.)
C
1128-030-2015
Piston Assembly (50mm)
Fits chain saw models:
044 / MS440.
With 12mm piston pin.
572-617
4238-030-2003
Piston Assembly (50mm)
Fits Cut Quik Saw
model: TS410.
(Replacement piston
assembly for our 570-276)
572-611
1115-030-2000
Piston Assembly (50mm)
Fits Stihl chain saw
model: 045.
572-515
1119-030-2002
1119-030-2003
Piston Assembly (52mm)
Fits chain saw model:
038 Magnum, MS380, MS381.
(Replacement piston assembly for our 570-272.)
572-261
1111-030-2000
Piston Assembly (52mm)
Fits chain saw models:
051 and
Cut Quik Saw model TS-510.
(Replacement piston assembly for our 570-162.)
1128-030-2009
Piston Assembly (52mm)
Fits chain saw models:
044 Big Bore, 046 and MS460.
572-615
Piston Assembly (50mm)
Fits chain saw model:
038 Super.
Application
Piston Assembly (50 mm)
Fits Stihl chain saw
models: 044 / MS440;
with a 10mm piston pin.
572-612
Piston Assembly (49mm)
Fits Cut Quik Saw
model: TS400.
continued
1122-030-2001
Piston Assembly (52mm)
Fits chain saw models:
064 / MS640.
16-42
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
572-613
1115-030-2001
Application
1122-030-2005
1118-034-3001
574-158
574-143
1111-030-2002
1106-030-2003
1106-030-2000
(Priced Individually - 2 Required)
574-137
1124-030-2005
(Priced Individually - 2 Required)
574-248
1110-034-3000
1110-034-3003
1121-034-3010
(Priced and sold in sets)
Piston Ring
(44mm X 1.5mm)
Fits chain saw models: 026 and MS260.
574-254
Also fits chain saw model: 041. Replacement ring for our 572-525
piston assembly. (Priced Individually - 2 Required)
(Priced and sold in sets)
C
1115-034-3010
Piston Ring Set
(52mm X 1.5mm)
Fits chain saw models: 038 Magnum,
MS380, MS381, 045, 048, 050, 051 and 056.
(Priced and sold in sets)
Piston Ring Set
(44mm X 1.5mm)
Fits chain saw models: 028, 030, 031 and 041.
1115-034-3001
1115-034-3010
Piston Ring
(52mm X 1.5mm)
Fits chain saw model: 038 Magnum, 051 and
TS510 cut quik saws. (Priced Individually - 2 Required)
1121-034-3005
1110-034-3000
1119-034-3000
Piston Ring
(50mm X 1.5mm)
For chain saw model: 038 Super.
Piston Ring Set
(42mm X 1.5mm)
Fits chain saw models: 024 / MS240.
574-216
1127-034-3006
4201-034-3000
Piston Ring
(49mm X 1.5mm)
Fits Cut Quik Saw model: TS-360 and TS400.
Piston Assembly (60mm)
Fits chain saw models:
084 and 088.
574-170
1125-034-3001
(Priced Individually - 2 Required)
574-106
574-212
1108-034-3001
Piston Ring
(48mm X 1.5mm)
Fits chain saw models: 034 Super,
036 and MS360. Replacement piston ring for our 572-497.
Piston Assembly (58mm)
Fits chain saw model: 070.
572-626
574-144
Application
Piston Ring
(47mm X 1.5mm)
Fits chain saw models:08, 08S and
Cut Quik model TS-350. (Priced Individually - 2 Required)
Piston Assembly (58mm)
Fits chain saw models:
075, 076 and TS760.
572-619
O.E.M
574-119
Piston Assembly (54mm)
Fits chain saw models:
066 / MS660.
572-620
Part#
(Priced Individually - 2 Required)
1115-030-2002
Piston Assembly (54mm)
Fits chain saw model: 056.
572-616
continued
Piston Ring
(46mm X 1.5mm)
Fits chain saw models: 028 Super and 034 (with smaller
46mm bore). Replacement ring for our 572-449 piston assembly.
Piston Assembly (52mm)
Fits chain saw models:
045 and 056AV - older version.
572-390
Banta
1115-034-3012
Piston Ring Set
(54mm X 1.5mm)
Fits chain saw models: 045 and 056.
(Priced and sold in sets)
Note: “Piston Rings” are priced and
sold individually. “Piston Ring Sets”
are priced and sold as a set of 2
16-43
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
591-102
9512-003-2250
Application
Bearing - Piston
Wrist pin bearing.
For Chain Saw models: 023, 025, MS230, MS250, 024,
026, MS260 and others. (Size: 10mm X 13mm X 12.5mm).
591-101
9512-003-3140
591-104
O.E.M
590-120
1106-030-0400
9512-003-3061
Crankshaft Assembly
For chain saw models: 070 and 090. (While Quantities Last)
593-102
9512-003-3281
9512-003-3440
Bearing - Piston
Wrist pin bearing for Chain Saw
models: 051 & 075
590-150
(While Quantities Last)
590-119
590-116
1108-030-0402
Crankshaft Assembly
For Cut Quik Saw models:
TS-350 and TS-360, also fits
Chain Saw models: 08 and 08S.
590-156
9503-003-0340
9503-003-0341
570-002
4223-020-9400
4238-020-9400
Wacker# 0104064
Decompression Valve
For Chain Saw and Concrete saw cylinder assemblies.
Fits models: TS400, TS700 and TS800
570-004
1128-020-9400
Decompression Valve
For Chain Saw and Concrete
saw cylinder assemblies.
Fits models: 026, 036, 044, 046, 066, MS260,
MS360, MS440, MS441, MS460, MS650, MS660.
640-269
4223-030-0400
Crankshaft Assembly
For Cut Quik Saw
model: TS400.
C
(While Quantities Last)
1111-030-0402
Crankshaft Assembly
For chain saw models:
051, 075 and
Cut Quik Saw model TS-510.
9503-003-0440
9503-003-0450
Bearing - Crankshaft
Fits models: 08S, 038,
038 Super, 038 Magnum and 041 - (clutch side).
Cut-Quik models: TS350 & TS360 - (clutch & flywheel
side); also fits Cut-Quik model: TS400. Fits models 034,
036, 044, 046, MS360, MS440 and MS460 (flywheel side).
Size: 15mm (37/64”) ID X 35mm (1-3/8”) OD X 11mm (7/16”) HT
(Bearing# 6202 - open both sides)
1110-030-0401
Crankshaft Assembly.
For Stihl chain saw
model: 041.
9503-003-0310
Bearing - Crankshaft
Fits Stihl chain saw models:
(flywheel side) 038, 038 Super, 038 Magnum, 051,
075 and TS-510 and TS-400 (recoil side) cut quik saws.
Also Stihl TS480i, TS500i, TS700 and TS800 Cutquik saws.
Size: 17mm ID X 40mm OD X 12mm HT.
(Bearing# 6203/C3) Open both sides
592-106
1119-030-0400
Crankshaft Assembly
For chain saw models: 038,
038 Super and 038 Magnum.
590-117
9503-003-0540
Bearing - Crankshaft
Fits chain saw model: 041 - (flywheel side)
Size: 15mm ID X 32mm OD X 9mm HT.
(Bearing# 6002/C3) Open both sides
593-103
Bearing - Piston
Wrist pin bearing for Chain Saw models: 066 & MS660.
(Size: 12mm X 17mm X 13mm).
591-110
Application
Bearing - Crankshaft
Fits chain saw models:
051 and 075 - (clutch side)
Size: 20mm ID X 47mm OD X 14mm HT.
(Bearing# 6204/C3) Open both sides
Bearing - Piston
Wrist pin bearing for Chain Saw models: 044,
046, MS440 and MS460. (Size: 12mm X 15mm X 15mm).
591-106
Part#
592-109
Bearing - Piston
Wrist pin bearing for chain saw models:
08S & 038, 038 Super / Magnum and
Concrete Saw models TS350 & TS360.
continued
Gasket Set
Fits chain saw model:
028 Super.
(No oil seals included)
16-44
(While Quantities Last)
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
Application
continued
Part#
O.E.M
640-234
640-279
Gasket Set
Fits chain saw models:
034, 034 Super, 036
Gasket Set
Fits chain saw models:
046 and MS460.
(Includes oil seals)
(No oil seals included)
Banta
Application
640-280
640-268
Gasket Set
Fits chain saw models:
066 / MS660.
(Includes oil seals)
Gasket Set
Fits chain saw models:
034, 036, MS340 and MS360.
640-281
(Oil seals included (1) 622-241
(15mm ID X 29.6mm OD X 4mm) +
(1) 622-226 (12mm ID X 20mm OD X 5mm).
640-272
Gasket Set
Fits Stihl concrete saw /
cut quik saw model: TS460.
Gasket Set
Fits chain saw model:
038 series.
640-282
(While Quantities Last)
(Includes oil seals)
640-136
Gasket Set
Fits Stihl concrete saw /
cut quik saw model: TS760.
(Oil seals included)
Gasket Set
Fits chain saw models:
050 and 051.
(No oil seals included)
(While Quantities Last)
623-611
1118-029-2305
Head / Base Gasket
Fits chain saw models:
026, 028, 031 and 032.
640-287
623-672
Gasket Set
Fits chain saw models:
08, 08S and Cut Quik
models: TS-350 and TS-360.
(Includes oil seals)
Head / Base Gasket
Fits chain saw models:
038, 038 Super & 038 Magnum.
640-181
4223-007-1050
Gasket Set
Fits Cut Quik model:
TS400.
(oil seals included)
640-285
4238-007-1003
Gasket Set
Fits cut quik / concrete
saw models:
TS410 and TS420.
(Includes oil seals)
For use with our 570-276 Cylinder Assembly.
1119-029-2300
(Fits our 570-208 and 570-272).
623-678
1110-029-2300
Head / Base Gasket
Fits chain saw model: 041.
623-687
1108-029-2300
Head / Base Gasket
Fits chain saw models:
08, 08S &Cut Quik models:
TS-350 and TS-360.
623-431
1111-029-2300
Head / Base Gasket
Fits chain saw models: 051
and Concrete saw model: TS510.
640-275
623-612
Gasket Set
Fits chain saw models:
044 and MS440.
(Includes oil seals)
Head / Base Gasket only
Fits Stihl chain saw
models: 044 / MS440. (Metal).
C
16-45
C
Banta
STIHL
Part#
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
continued
Part#
O.E.M
623-613
610-121
1119-358-7700
1118-358-7701
Head / Base Gasket only
Fits Stihl chain saw
models: 046 / MS460. (Metal).
Molded Fuel Line
For chain saw models: 034, 034 Super and
036 (previous to serial number) X39108850; 038 series as
well as model 064 (previous to serial number X19512349.)
Measures: 4-3/4” Long
O.E.M
Application
623-614
610-128
Head / Base Gasket only
Fits Stihl chain saw
models: 066 / MS660. (Metal).
610-129
Head / Base Gasket only
Fits Stihl concrete / cut quik saw
model: TS400. (Metal).
1115-350-3503
0000-350-3500
610-130
1110-358-1800
0000-350-3500
1115-350-3503
610-134
0000-350-3504
1115-350-3503
Fuel Filter - In Tank
For use with molded fuel lines. Fits chain saw models:
034, 036, 038, 044, MS440, 046, MS460, 064, MS640,
066, MS660 etc with molded fuel lines.
NOTE: Similar to our our 613-605 but larger diameter.
Recommended for larger cc Stihl chain saws. etc. Measures:
1-3/4” overall length X 23mm diameter.
610-125
1123-358-7701
1123-358-7702
Molded Fuel Line
Fits chain saw models:
021, 023, 025, MS210, MS230, MS250.
Note: Designed to be used with engines manufactured before January
2012; Not to be used with engines manufactured after January 2012.
610-122
1127-358-7702
Molded Fuel Line
Fits chain saw models:
029, 034, 036, 039,
MS290, MS360, MS390.
C
1106-647-9404
Molded Oiler Hose / Oil Tube
Fits the following chain saw
models: 028, 030, 031, 032, 038, 070, 075, 090,
MS 380, MS 381. This hose connects to the oil pump.
Fuel Filter - In Tank
Use with molded fuel lines. Fits chain saw models:
034, 036, 038 etc with molded fuel lines.
Measures: 11/16” OD X 1-5/8” overall length.
613-607
1124-358-7700
Molded Fuel Line
For Stihl. Fits chain saw
models: 066, MS650 and MS660.
610-132
Replacement Fuel Filter Element
For our 610-170.
Will replaces the original Stihl element.
Measures: 1” L X 3/4” OD (Made of foam material).
613-605
1128-358-7701
Molded Fuel Line
Fits chain saw models: MS341,
MS361, 044, 046, MS440 & MS460.
Fuel Filter
For chain saw models
using 1/4” molded fuel lines. Models: 038,
044, 044, 046, MS460, 064, 066 etc. (Orange colour).
610-055
1119-358-7702
Molded Fuel Line
Fits chain saw models: MS381
623-615
610-170
Application
1122-647-9400
Molded Oiler Hose / Oil Tube ONLY,
Pick-up filter body not included.
Oil pump pick-up hose only. Fits the following Stihl chain
saw models: 024, 026, 034, 034, 036, 036QS, 064, 066,
MS240, MS260, MS260C, MS340, MS341, MS360,
MS360C, MS361, MS361C, MS362, MS362C, MS441,
MS441C, MS640, MS650 and MS660.
550-120
1110-350-0502
Fuel Cap
For chain saw
models: 041, 051 and 075.
550-145
0000-350-0520
1117-350-0500
Fuel & Oil Cap (40mm)
Gas Cap for chain saw models:
020, 021, 023, 024, 025, 026,028, 028 Super, 029,
034, 034 Super, 036, 038 series, 039, 044, 046, MS290,
MS310 and MS390. Oil Cap for Stihl chain saw models:
044, 046, 050, 064, 084, MS640, MS650 and MS660.
550-158
0000-350-0531
1124-350-0500
Fuel Cap
For chain saw models:
064, 066, MS660 and 084.
Thread OD: 1.54” or 39.06mm
16-46
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
550-121
1107-350-0500
Application
Fuel Cap
For chain saw models:
08, 08S, 070, 090
and Cut Quik models: TS-350 and TS-360.
551-149
continued
Part#
O.E.M
627-380
1119-640-3200
Application
Oiler / Oil Pump Assembly
Fits chain saw
models: 038, MS380,
MS381, 042AV and 048.
0000-350-0510
1117-640-3600
Oil Cap and Fuel Cap (30mm)
For chain saw models: 009, 010,
011, 012, 020, 021, 023, 024, 025, 026, 028,
028 Super, 032, 034, 034 Super, 036, 038,
042 and 048. Fuel Cap for chain saw model: 048.
551-155
Banta
627-326
1121-007-1043
1121-640-3203
Oiler / Oil Pump Assembly
Fits chain saw models:
024, 026, MS240 and MS260.
0000-350-0526
Oil Cap
For chain saw models: HT 100,
HT 101, HT 130, HT 131,
HT 250, HT 70, HT 73,
HT 75, HTE 60, HT-KM.
627-336
Gas CAP
For the following models: 021, 023, 025, 026, 034, 036,
036QS, MC 200, MS 171, MS 181/C, MS 192/C/T, MS
200/T, MS 210/C, MS 211, MS 230/C, MS 240, MS 250/C,
MS 260/C, MS 340, MS 360/C and MS 381.
(Flip Top Style). Size: O-Ring Seal OD = 1.20”.
1125-640-3201
Oiler / Oil Pump Assembly
Fits chain saw models:
034, 036 and MS360.
627-346
1128-640-3206
NOTE 1: Two pictures shown for reference.
NOTE 2: NOT compatible with > 10% ethanol fuel.
550-160
0000-350-0525
Fuel Cap
For chain saw models:
020, 021 023, 024, 025, 026, 029,
034, 036, 039, 044, 046, 088,
BG45, BG46, BG55, MS171, MS181,
MS192, MS200, MS210, MS211,
MS230, MS240, MS250, MS260, MS270,
MS290, MS310, MS340, MS341, MS360, MS361, MS362,
MS380, MS381, MS440, MS441, MS460 and MS880.
(Flip Top Style). Size: O-Ring Seal OD = 1.35”.
Note: NOT compatible with > 10% ethanol fuel.
550-164
1122-640-3205
Oiler / Oil Pump Assembly
Fits chain saw models:
066 / MS660.
627-026
1121-640-7111
Worm Gear
Fits chain saw models: 026, MS260
and (Later Type) MS240 and MS261.
627-029
Note: NOT compatible with > 10% ethanol fuel.
1119-640-7100
1119-642-1501
Oil Pump Spur Gear &
Oiler Worm Gear Set for Stihl.
Includes (1) oil pump spur gear
(Replaces Stihl# 1119-642-1501).
This nylon gear drives the oiler
gear on saw & fits Stihl chainsaw
models: 038, MS380 & MS381 ONLY. Also included is (1)
oiler worm gear (Replaces Stihl# 1119-640-7100). This nylon
sprocket comes complete with bushing attached. It drives the
oiler and fits on Stihl chainsaw models: 038, MS380, MS381
as well as 028, 042 and 048 models.
C
627-660
4223-350-0500
Fuel Cap / Gas Cap
For Stihl concrete /
cut quik saw model: TS400.
627-038
Oiler / Oil Pump Assembly
Fits chain saw models:
046, MS460, MS441 & MS441C.
1125-640-7110
1125-647-2400
Worn Gear and Spring
Fits chain saw models:
029, 034, 036, 039.
600-169
0000-400-1306
Electronic Coil
Fits chain saw models:
009, 010, 011, 012, 020,
020T, 021, 023, 025,
MC 200, MS200, MS210,
MS230 and MS250.
16-47
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
600-402
1123-400-1301
Application
430-027
1100-430-0202
1110-430-0210
1121-430-0200
636-150
636-152
1122-400-1314
636-151
1127-140-0605
1125-140-0607
Muffler / Exhaust
For chain saw models: 036,
MS360 and will fit some
034 Super models see measurements.
Mounting bolt holes
measure: 1.69” / (43mm) center to center /
bolt holes measure: 7.3mm OD.
Muffler measures: 3” deep approximately.
600-100
636-138
Ignition Coil and Core
For chain saw models:
08 and 08S.
NOTE: Found on other
equipment using the old 08
style power plant. ie: Stihl auger etc.
1119-140-0604
Muffler
For chain saw models: MS381.
(Uses our 623-132 exhaust gasket).
For older 038 series see our 636-139 muffler.
600-901
636-139
Ignition Coil and Core
For chain saw
models: 041 and 045.
1111-400-1305
1113-400-1305
1119-007-1005
1119-140-0600
1119-007-1027
Muffler / Exhaust
For chain saw models:
038 and 038 Super.
Note: Front and back
images shown for reference.
(Uses our 623-132 exhaust gasket)
Ignition Coil
For chain saw models: 051
C
1121-140-0606
Muffler / Exhaust
For chain saw models:
029, 039, MS290,
MS310 and MS390.
4223-400-1303
NOTE 1: We are not certain
which OEM# (original equipment
manufacturer number) is correct.
Please see picture for reference.
Universal Type
Muffler / Exhaust
For chain saw models:
024, 026 and MS260.
Ignition Coil
For concrete / cut quik
saw. Fits model: TS400.
Two bolt style (bolts not included).
Coil comes complete with
13” of 5mm coil wire.
600-401
Application
Toggle Kill Switch
Kill switch found on many small older
Chain Saw models with spade terminal wire end.
Electronic Ignition.
Fits on Stihl chain saw
models: 046, 066,
MS460, MS650 and MS660
600-400
O.E.M
430-017
0000-400-1300
Electronic Ignition
For chain saw models: 024, 026,
028, 028WB, 029, 034,034AV, 036,
038, 039, 044, 048, 064, MS240,
MS260, MS290, MS310, MS340,
MS360, MS380, MS381, MS390,
MS440 and MS640;
also Trimmer models: FS360 and FS420.
600-406
Part#
Stop Switch
Kill Switch for chain saw models: 024, 026, 070
and Cut Quik Saw models 08S, TS-350 and TS-360.
Measures: 3/4” X 1” X 1-1/2”
Electronic Coil
Fits chain saw
model: MS250.
600-358
continued
623-132
(While Quantities Last)
1117-149-0601
1115-149-0601
Chainsaw Exhaust Gasket
For chain saw models: 038 series.
16-48
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
636-297
1110-140-0613
Application
Muffler / Exhaust
Muffler for chain saw models:
040, 041 and 041G.
1128-140-0616
Muffler / Exhaust
Dual port muffler for chain saw
models: 044, 046, MS440 & MS460.
This is an aftermarket muffler.
The dual port design add power.
Complete with front baffle and spark arrester screens.
636-156
1122-140-0613
1122-140-0800
4201-140-0607
4201-149-0601
Oil Seal (PTO side)
Fits chain saw models: 038 and 038 Super.
Size: 17mm X 39.5mm OD X 5mm
622-249
135-061
Muffler / Exhaust
For Cut Quik Saw models:
TS350 and older TS360.
(While Quantities Last)
9640-003-1610
0000-350-6202
1130-350-6200
1128-405-1000
9640-003-1340
9640-006-1314
1118-648-0400
1119-648-0400
Sprocket Side Cover
For chain saw models:
024 and 028 (new).
650-154
Oil seal
For chain saw models: 028, 030, 031, 032, 038,
MS380, MS381 (Magneto side). Trimmer models: FS360,
FS420, FS500 and FS550 and Blower models: BR 320,
BR 340 L, BR 380, BR 400, BR420, BR420 C, SR 320, SR
400, SR 340 and SR 420. Size: 13mm X 22mm OD X 5mm
Universal
Spark Plug Wire (5mm OD)
Plug Wire for chain saw
models: 08, 08S and
Cut Quik Saw models:
TS-350 and TS-360.
Quality black hypolon outer case with
COPPER (not carbon) inner wire. 5mm Spark
(Priced and Sold in 10 meter / 33 FT rolls)
650-141
9640-003-1190
Oil seal
For models: 020, 024, 026, 034, 036, MS360, FS220, & 280
Size: 12mm X 20mm OD X 5mm.
C
9640-003-1880
Spark Plug Boot with Spring
For chain saw models: 009,
010, 011, 012, 017, 018, 020,
021, 023, 024, 025, 026, 029,
034, 036, 039, 044, 046, 056,
064, 066, 084, 088, MS170, MS180, MS192T, MS210,
MS230, MS240, MS250, MS270, MS290, MS310, MS340,
MS341, MS360, MS361, MS380, MS390, MS440, MS441,
MS460, MS640, MS650, MS660 and MS880.
Note: Front and back images
shown for reference.
622-233
622-266
135-110
Muffler / Exhaust
For models:08 and 08S.
622-226
9640-003-1600
Mounting hole: .576” (Uses our 615-028 replacement primer bulb).
Note: This primer assembly has a coil spring inside the primer bulb.
1108-140-0600
NOTE: photo shows front and
back images.
622-241
Application
Primer Bulb Assembly
Fits Zama carburetors.
Found on Stihl concrete / cut off saw
models: TS400, TS800;
(Also see our 636-156)
636-171
O.E.M
615-514
Muffler / Exhaust
Dual Port muffler for
chain saw models:
066, MS660 and MS650.
636-117
Part#
Oil Seal (PTO & Mag side)
Fits chain saw models: 08 / 08S &
Cut Quik models: TS350and TS360.
1122-140-0614
Muffler / Exhaust
Single Port muffler
for chain saw models:
066, MS660 & MS650.
636-153
continued
Oil Seal (Clutch Side).
Fits chain saw models:
026, 028 Super, 034, 036, 044, MS440, 046 and MS460.
Trimmer models: FS360, FS420, FS500 and FS550.
Size: 15mm X 29.6mm OD X 4mm HT. NOTE: You can find
(1) 622-241 oil seal in our 640-268 gasket set.
(Uses our 623-157 exhaust gasket)
636-154
Banta
(While Quantities Last)
1125-640-1701
1125-648-0402
Sprocket Side Cover
Fits chain saw models:
024, 026, 028 Super,
029, 034, 036, 038, 038 Magnum.
(Made of Plastic)
16-49
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
650-124
1108-640-1705
Application
continued
Part#
O.E.M
655-029
1127-080-2103 / A
Application
Sprocket Side Cover
For chain saw models:
08 and 08S.
Complete with tank cover.
Starter Assembly
For chain saw models: 029, 031, 039, MS290, MS310, MS390.
681-134
Sprocket Needle Bearing
Fits many chain saw
manufacturers drive sprockets.
Fits chain saw models: 009, 010, 011, 012, 021,
023, 024, 025, 026, 34 and 36 (PRIOR TO x25809074).
(Size: 10mm X 13mm X 10mm)
This aftermarket assembly comes complete with housing,
starter pulley, spring, rope, pawls, handle etc. Just needs to be
bolted on. (Housing is made of plastic).
655-034
1125-080-2105
NOTE: This bearing will not replace the plastic needle bearing
type used on newer models.
681-125
0000-993-3008
Sprocket Needle Bearing
For chain saw models: 08S and
Cut-Quik models: TS350 and TS360.
(Size: 15mm X 18mm X 17mm)
Starter Assembly
For chain saw models:
034, 034 AV, 034 Super, 036, MS340 and MS360.
NOTE: This bearing will not replace the
plastic needle bearing type used on newer models.
This aftermarket assembly comes complete with housing,
starter pulley, spring, rope, pawls, handle etc. Just needs
to be bolted on. (Made of metal).
681-128
655-038
1119-080-1800
Sprocket Needle Bearing
Fits models: 028 series.
(Size: 10mm X 13mm X 23mm)
681-127
Sprocket Needle Bearing
Fits chain saw models:
038. 042, 048 (Spur Only)
(Size: 12mm X 16mm X 24mm)
681-126
Starter Assembly
For chain saw models: 038 series.
This aftermarket assembly comes complete with housing, starter
pulley, spring, rope, pawls, handle etc. Just needs to be bolted on.
(Made of cast metal).
9512-933-2382
Sprocket Needle Bearing
Fits our chain saw sprockets
fitting on models: 044, 046, MS440, MS460, 064, 066,
MS640 and MS660. NOTE: Will also replace the original
STIHL (plastic cased needle bearing) in the MS390.
(Size: 10mm X 16mm X 12mm)
655-044
1128-080-2104
Starter Assembly
For chain saw models: 044, 046, MS440 and MS460.
681-129
This aftermarket assembly comes complete with housing, starter
pulley, spring, rope, pawls, handle etc. Just needs to be bolted on.
(Made of cast metal).
Sprocket Needle Bearing
Fits our chain saw sprockets
fitting on models: 084, 088.
(Size: 12mm X 17mm X 13mm)
655-066
1122-080-2110
671-110
Sprocket Nut
(While Quantities Last)
Fits chain saw models: 08, 08S;
also found on older Cut Quik model: TS350
672-110
Flywheel Nut
Fits chainn saw models: 08,
042, 045, 056, 070, 090; also
found on Cut Quik models: TS350 & TS360
C
Starter Assembly
For chain saw models: 066, MS650 and MS660.
This aftermarket assembly comes complete with housing,
starter pulley, spring, rope, pawls, handle etc. Just needs to be
bolted on. (Made of cast metal).
16-50
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
655-035
1108-080-2101 / 1108-080-2115
Application
Starter Assembly
For chain saw model:
08 & 08S and Concrete / Cut Quik saw model: TS350.
This aftermarket assembly comes complete with plastic housing,
metal starter pulley, spring, rope, pawl, elasto starter handle etc.
Just needs to be bolted on. (This assembly is the newer - 1 nylon
starter pawl set up).
655-040
4223-190-0401
O.E.M
560-120
1113-195-8200
0000-190-3400
This aftermarket assembly comes complete with housing,
starter pulley, spring, rope, pawl, handle etc. Just needs to be
bolted on. (Made of Nylon)
Elasto Starter Handle
and Rope
For many Stihl saws.
Medium starter handle with
rubber buffer to help obsorb the kick that
you get from some of the larger Stihl saws.
Rope diameter is 4mm X 36 inches long.
560-121
4238-190-0300 / 4238-190-0301
4238-190-0302 / 4238-190-0402B
Starter Assembly
For concrete saw / cut quik saw models: TS410 and TS420.
This aftermarket assembly comes complete with housing, starter
pulley, spring, rope, pawl, handle etc. Just needs to be bolted on.
(Made of Nylon)
560-119
560-170
(Sold in multiples of 10)
1121-195-3400
1117-195-7200
Size: 1.11” overall length X
.375” overall height not including positioning nub.
1124-195-0401
1124-195-7200
Starter Pawl (nylon)
For Stihl chain saw models:
038, 041, 042, 045, 048, 050,
051, 056, 064, 066, 070, 076,
08S, 084, 088, MS380, MS640, MS650, MS660, MS880;
also fits Cut Quik Saw models TS350 and TS360.
Size: 1.12” overall length X .475” overall height not
including positioning nub. (newer style)
1125-195-7200
4116-195-7200
Starter Pawl (nylon)
For chain saw models:
009, 010, 011, 012, 017, 018, 019T, 020,
020T, 021, 023, 024, 025, 026, 028, 029,
034, 036, 039, 044, 046, MS170, MS180, MS190T,
MS191T, MS192T, MS200, MS200T, MS210, MS230,
MS2400, MS250, MS260, MS270, MS290, MS310,
MS3400, MS341, MS360, MS 361, MS440 and MS460.
560-784
0000-195-7200
4116-195-7200
1110-195-3400
Starter Handle
For chain saw models:
08, 038, 041, 042, 050, 051,
056, 070, 075 and 090. (Old style)
C
1118-195-7200
Starter Pawl (nylon)
For Stihl chain saw models: 08, 038,
042, 048, 051, 056 and 070 (old style).
560-203
Starter Handle
(Sold in multiples of 10)
For chain saw models:
021, 023, 024, 026, 028, 028 Super, 034, 034 Super, 036,
044, 046, 064, 066 (New style), concrete saw
models: TS350, TS360, TS510 and TS360
560-118
1122-190-3400
Elasto Starter Handle
and Rope
For many Stihl saws.
Large starter handle with
rubber buffer to help obsorb the kick that
you get from some of the larger Stihl saws.
Rope diameter is 4.5mm X 38 inches long.
560-202
560-213
Application
Starter Pawl (nylon)
For Stihl chain saw models: 009, 010,
011, 012, 024, 028 (old style) and 032.
Starter Assembly
For concrete saw / cut quik saw model: TS400.
Starter Handle
For chain saw models: 010,
011, 015, 021, 028, 031 and 032.
continued
Part#
560-111
655-042
Banta
(Sold in multiples of 10)
Starter Pawl (metal pin)
Fits concrete saw model:
TS400; as well as models:
BR320, BR320L, BR340, BR340L,
BR380, BR400, BR420, BR500, BR550, BR600 back pack
blowers; FR220, FS106, FS160, FS180, FS220, FS280.
16-51
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
630-095
1118-195-3500
Application
Spring Clip / Pawl Spring
(Sold in multiples of 5)
Fits chain saw models:
009, 010, 011, 012, 024,026, 028, 032 old style.
(For use with our 560-111 starter pawls).
630-111
1128-195-3500
Spring Clip / Pawl Spring
Fits chain saw models:
(Sold in multiples of 5)
024, 026, 028, 034, 036, MS360,
039, MS390, 044, MS440, 046, MS460 etc.
(For use with our 560-203 starter pawls).
630-118
1124-195-3500
continued
Part#
O.E.M
560-224
1117-007-1014
1117-195-0402
Application
Starter Pulley (metal)
For chain saw models:
038, 041, 042, 045, 048,
051, 056, 08, 070, 075, 076,
and Cut Quik models:
TS350, TS360, TS510 & S760.
Measures: 3-1/8” OD (2) pawl pulley
(Uses our 560-202 & 630-179)
560-146
1107-190-1000
Starter Pulley (metal)
For chain saw models:
08, 08S and 070.
Measures: 3” OD (2) pawl pulley
Spring Clip / Pawl Spring
Fits chain saw models: 064,
066, MS640, MS660 and 084.
Size: 1-3/4” overall length X 1-1/8” approximately
560-200
1122-195-0400
(For use with our 560-202 starter pawls).
630-179
1117-195-3500
Spring Clip / Pawl Spring
Fits chain saw models: 038, 041, 042,
045, 048, 050, 051, 056, 070, 076, 08S, MS380 & MS381.
560-189
1123-195-0400
Starter Pulley (nylon)
Fits chain saw models:
017, 018, 019, 020, 021,
023, 025, MS170 / 180 /
190 / 191 / 192 / 200 MS210, MS230 and MS250.
Measures: 2-1/2” OD (2) pawl pulley
560-190
1118-190-1000
(Two Images shown for reference)
560-101
560-116
1128-195-0400
Starter Pulley (nylon)
For chain saw models: 029, 034,
036, 039, 044, 046, MS261, MS271,
MS290, MS291, MS310, MS311,
MS340, MS341, MS360, MS361,
MS362, MS390, MS391, MS440, MS441 and MS460.
Measures: 2-11/16” OD (2) pawl pulley
C
4238-190-1001
1106-190-4600
Starter Dog Assembly
(Large)
Found on many older
chain saws using an aluminum starter cup.
Size: Dog width: 1/2” with a 3/8” ID.
1125-195-0400
1125-195-0401
Starter Pulley (nylon)
For chain saw models:
024, 028 (new-style) and 034.
Measures: 2-3/4” OD (2) pawl pulley
560-237
560-225
Starter Pulley
With brass bushing. For Cut Quik / Cut off saw models:
TS410, TS420, TS480i and TS500i.
Measures: 3” (76.82mm) Bottom OD X
2.74” (69.63mm) Top OD X .412 (10.47mm) ID / Bore.
(1) pawl pulley. Uses our 560-784 Starter Pawl.
Starter Pulley (nylon)
For chain saw models:
028 and 024 (old style).
Measures: 2-9/16” OD (1) pawl pulley (While Quantities Last)
560-201
Starter Pulley (nylon)
For chain saw models:
08S, 051, 064, 066,
MS640, MS650 and MS660.
Measures: 2-27/32” OD (2) pawl pulley
0000-961-5116
Starter Ring (nylon)
For chain saw models:
08S, 041, 045 and 070.
Size: 2-1/4” OD
625-500
1111-195-1600
Starter Spring
For chain saw models:
FS08, FS410, 410AV,
410 AVE (...5816400)
16-52
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
STIHL
continued
Part#
O.E.M
625-501
1113-195-1600
Application
Starter Spring
For chain saw models:
030 and 031.
625-502
1116-195-1600
1118-190-0600
1114-190-0600
625-522
625-518
1115-190-0600
1160-190-0600
625-519
625-520
1117-190-0601
Starter Spring
For chain saw models:
040 and 041 (...#2663618).
C
1122-190-0605
1124-190-0600
1129-190-0600
Starter Spring
For chain saw models:
017, 021, 023,
025, 029 and 039.
1117-190-0600
1110-190-0600
1122-190-0600
Starter Spring
For chain saw model:
084.
Starter Spring
For chain saw models:
038, MS380, 041 (#5816401...),
042 (after serial# 5676790),
045 (before serial# 5919431...),
048, 050, 051 (after serial# 674961...), 056, 070, 075, 076
and Cut Quik models: TS-350, TS-360, TS510 and TS760
(new model - narrow spring).
625-510
1128-190-0600
Starter Spring
For chain saw models:
066, MS650 and MS660.
Comes complete with nylon case.
Starter Spring
For chain saw model:
042.
625-509
1120-195-1600
Application
Starter Spring
For chain saw models:
064 and 066.
Starter Spring
For chain saw models:
08, 070, 090, 510 and
Cut Quik Saw model: TS350
(old model - wide spring).
625-508
625-511
625-517
Starter Spring
For chain saw model:
045. (...#5919431)
625-507
O.E.M
Starter Spring
For chain saw models:
036, 044 and 046.
Starter Spring
For chain saw model:
FS150, 151,
200AV and 200AVSE.
625-506
Part#
625-516
Starter Spring
For chain saw models:
024, 026, 028, 032 and 034.
625-504
continued
Starter Spring
For chain saw models: 009,
010, 011 (X12725130...) and 012.
Starter Spring
For chain saw models:
009, 010, 011 (...X12725130) and 015.
625-503
Banta
4223-190-0600
Starter Spring
For Cut Quik Saw /
Concrete Saw model: TS400.
Measures: 2.348” diameter
625-521
1129-190-0601
Starter Spring
For chain saw models:
034, 044 and 046.
625-526
4282-190-0600
4282-195-0300
Starter Spring
For Cut Quik Saw / Concrete Saw
model: TS410 and TS420.
Measures: 2.479” diameter
16-53
C
Banta
STIHL
CHAIN SAW ACCESSORIES - O.E.M
STIHL
continued
Part#
O.E.M
875-272
9490-000-7840
9490-000-7850
Application
Drive Belt (Cogged Belt)
For concrete / cut off saw
models: TS350, TS360 and TS460.
Size: 3/8” W X 33-3/4” L
875-273
continued
Part#
O.E.M
654-128
1110-790-1510
Tube Handle
For chain saw model:
041 (old style).
9490-000-7851
654-133
Application
(While Quantities Last)
1110-790-1716
Drive Belt (Cogged Belt)
For concrete / cut off saw
model: TS400.
Size: 3/8” W X 34-7/16” L
875-3822
Tube Handle
For chain saw model:
041 (new style).
9490-000-7891
9490-000-7892
654-126
Drive Belt (Cogged Belt)
For concrete / cut off saw
model: TS510 & TS760,
with 14” blade Size: 3/8” W X 36.3” L
(While Quantities Last)
1108-790-1500
(Kevlar - Cogged Raw Edge V-Belt).
875-3821
Tube Handle
For chain saw model:
08S and Cut Quik models:
TS350 & TS360.
9490-000-7900
Drive Belt (Multi Ribbed)
For concrete / cut off saw
models: TS420.
Size: 7/16” W X 32” L.
875-3820
654-145
Tube Handle
For chain saw models:
064 and 066.
(While Quantities Last)
654-129
1118-790-1700
(While Quantities Last)
1119-790-1700
Tube Handle
For chain saw models:
038 and 038 Super.
C
654-125
Wrap Handle
For chain saw models:
MS230 and MS250.
Tube Handle
For chain saw models:
028 and 028 Super.
654-137
(While Quantities Last)
1121-790-1701
Tube Handle
For chain saw
model: 024.
654-139
1122-790-1700
9490-000-7901
Drive Belt (Multi Ribbed)
For concrete / cut
off saw models: TS410.
Size: 1/2” W X 29-1/2” L.
654-143
(While Quantities Last)
(While Quantities Last)
Wrap Handle
For chain saw models:
MS290 and MS390.
654-140
1128-790-1750
1128-790-1753
Wrap Handle
For chain saw models:
044, 046, MS440 and MS460.
16-54
C
CHAIN SAW ACCESSORIES - O.E.M
STIHL
Part#
STIHL
continued
O.E.M
705-574
Application
A
Banta
continued
Part#
O.E.M
705-592
Carlton# 41C1319T
Oregon# 57-019
Application
B
C
T Wrench / Scrench
Fits models: 009, 010, 011, 015, 020, 021, 023, 024,
025, 026, 028, 031, 032, 034, 036, 038, 041, 048 and 056.
Bar nut= 1/2” or 13mm. Spark plug = 3/4” or 19mm
A = 6-3/4”, B = 1-1/16”, C = 1
705-590
T Wrench / Scrench
Used on Husqvarna and Stihl
cut quik / cut off / concrete saws.
Fits Stihl concrete / cutquik saw
models: TS350, TS350AVE, TS360,
TS400, TS460, TS700 and TS800.
Size: 1/2” (13mm) Bar Nut X
3/4” (19mm) Spark Plug X
(B = 2”) + (C = 1”) = 3” total
with a 7-3/4” long handle. T27 Torx End.
705-634
A
B
C
T Wrench / Scrench
Fits chain saw models: 044, MS440, 046, MS460, 064, MS640.
Bar nut= 1/2” or 13mm. Spark plug = 3/4” or 19mm
A = 7”, B = 1-5/8”, C = 1”
705-635
T Wrench / Scrench
Fits most new Stihl chain saws.
Size: 11/16” (17mm) Bar Nut X
3/4” (19mm) Spark Plug X
(B = 1-7/16”) + (C = 1-1/2”) =
2-15/16” total with a 7-3/4” long handle.
T27 Torx End.
TANAKA
Carlton# 41C1719
625-850
A
779 00601 203
B
C
T Wrench / Scrench.
Bar nut= 11/16” or 17mm. Spark plug = 3/4” or 19mm
A = 6-3/4”, B = 1-5/16”, C = 1-5/16”
Starter Spring
For chain saw models:
ECS-350 and 355.
625-854
777 11600 911
705-525
A
B
C
Starter Spring
For chain saw models:
ECS-506 and 650.
625-858
778 00601 900
778 01800 900
T Wrench / Scrench
Fits chain saw models: 08S, 051, 051, 075, 090 and
Cut Quik models: TS350 & TS360.
Bar nut= 11/16” or 17mm. Spark plug = 13/16” or 21mm
A = 7”, B = 1-11/16”, C = 1-5/8”
705-202
5910-890-2400
Torx Wrench
For bolts found on Stihl equipment.
Special 6 - sided torx head.
NOTE: Picture shows a close up of torx end for reference
C
Starter Spring
For chain saw models:
ECS-351, 356, 405 and 415.
625-859
778 11600 910
Starter Spring
For chain saw models:
ECS-505.
16-55
C