16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
www.aal.net
TM
Y-LED Upgrade Kit Installation Guide
Fixture: SLVT - LARGENT
!
WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical
Code. Failure to do so may result in serious personal injury.
MAINTENANCE: A regularly scheduled maintenance program should be established to retain optimum light
output and reduce heat retention. Dusting with a soft, clean, dry cloth is normally sufficient for the optics.
CAUTION: All wiring must be done by a qualified electrician. KEEP THIS SHEET FOR FUTURE REFERENCE.
UPGRADE KIT CONTENTS
1
2
UPGRADE KIT CONTENTS
ITEM #
PART #
QTY
DESCRIPTION
1
93049910
1
RETROFIT KIT Y-LED SLVT
2
A84005
2
8-32 WINGNUT
PAGE 1/5
93049909 REV. A
ARCHITECTURAL
AREA
LIGHTING
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
www.aal.net
TM
Y-LED Upgrade Kit Installation Guide
Fixture: SLVT - LARGENT
1.
!
REMOVE TOP COVER
TURN OFF ALL POWER TO THE UNIT AND
TAKE PROPER SAFETY PRECAUTIONS.
FAILURE TO DO SO MAY RESULT IN SERIOUS
PERSONAL INJURY.
TOP COVER
1. REMOVE TOP COVER BY LOOSENING
FOUR (4) 1/4-20 X 2" SCREWS. (FIG. 1-1)
1/4-20 X 2" SCREWS
4X
A
FIG. 1-1
DETAIL A
PAGE 2/5
93049909 REV. A
ARCHITECTURAL
AREA
LIGHTING
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
www.aal.net
TM
Y-LED Upgrade Kit Installation Guide
Fixture: SLVT - LARGENT
2.
REMOVE EXISTING REFLECTOR ASSEMBLY
AND HID COMPONENTS.
1. DISENGAGE QUICK-DISCONNECT AND PULL
APART. (FIG. 2-1)
2. REMOVE REFLECTOR BY REMOVING TWO
8-32 WINGNUTS. DO NOT DISCARD
WINGNUTS.(FIG. 2-1)
REFLECTOR
ASSEMBLY
8-32 WINGNUT
2X
QUICKDISCONNECT
3. REMOVE BALLAST BY REMOVING 2X
1/4-20 SCREWS. LOOSEN 8-32 SCREW AND
REMOVE IGNITOR AND CAPACITOR. DRILL
RIVETS OUT AND REMOVE CAPACITOR
BRACKET. (FIG 2-2)
4. DISCONNECT ALL WIRE CONECTIONS.
RIVETS
2X
8-32 SCREW
IGNITOR AND
CAPACITOR
BALLAST
1/4-20 SCREWS
2X
CAPACITOR
BRACKET
FIG 2-2
PAGE 3/5
93049909 REV. A
ARCHITECTURAL
AREA
LIGHTING
FIG2-1
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
www.aal.net
TM
Y-LED Upgrade Kit Installation Guide
Fixture: SLVT - LARGENT
3.
INSTALLING Y-LED MODULE
1. LINE UP Y-LED MODULE ASSY CARRIER
PLATE HOLES OVER SCREWS, SECURE
MODULE TO HOUSING WITH TWO
WINGNUTS. (FIG. 3-1)
2. USING EXISTING HARDWARE BOND RING
TERMINAL TO HOUSING. (FIG. 3-1)
3. CONNECT QUICK-DISCONNECT. IF
REQUIRED, ATTACH PROVIDED FEMALE
QUICK-DISCONNECT WIRE HARNESS USING
PROVIDED CRIMP CONNECTORS. (FIG. 3-1)
4. MAKE ALL WIRE CONNECTIONS.
Y-LED MODULE
ASSEMBLY
8-32 WINGNUT
2X
QUICKDISCONNECT
FEMALE QUICKDISCONNECT HARNESS
CRIMP CONNECTOR
GROUND QUICKDISCONNECT
RING TERMINAL
FIG 3-1
PAGE 4/5
93049909 REV. A
ARCHITECTURAL
AREA
LIGHTING
16555 East Gale Avenue
City of Industry, CA 91745
626.968.5666
www.aal.net
TM
Y-LED Upgrade Kit Installation Guide
Fixture: SLVT - LARGENT
4.
INSTALLING TOP COVER
TOP COVER
1. RETURN TOP COVER TO ITS ORIGINAL
POSITION AND SECURE WITH (4) 1/4-20
SCREWS. (FIG. 4-1)
2. INSTALLATION COMPLETE.
1/4-20 X 2" SCREWS
4X
FIG. 4-1
PAGE 5/5
93049909 REV. A
ARCHITECTURAL
AREA
LIGHTING
CATALOG NUMBER
INSTALLATION INSTRUCTIONS
SLVT-LED (MICROCORE)
TOP CLOSURE
COVER ASSEMBLY
(4) DRIVERS
EMITTER DECK
HOUSING
(4) CAPTIVE SCREWS
FIXTURE INSTALLATION STEPS:
1) TURN POWER OFF.
2) MAKE WIRE CONNECTIONS FROM
INCOMING SUPPLY TO FIXTURE ASS'Y.
(NOTE: FIXTURE ASSEMBLY MUST BE
GROUNDED TO INCOMING EQUIPMENT
GROUND SUPPLY).
3) SLIP-FITTER OVER TOP OF POLE. SECURE
FITTER WITH (3) STAINLESS STEEL SET SCREWS.
4) INSTALLATION COMPLETE.
(3) STAINLESS STEEL
SET SCREWS
TO SERVICE EMITTER DECK/DRIVER:
1) TURN OFF POWER.
2) LOOSEN (4) CAPTIVE SCREWS LOCATED AT
THE BOTTOM OF THE FIXTURE AND OPEN TOP
CLOSURE COVER ASSEMBLY.
3) INTERIOR OF THE HOUSING IS EXPOSED.
4) SERVICE EMITTER AND DRIVERS AS NEEDED.
5) TO RE-ASSEMBLE REVERSE PROCEDURE.
16555 East Gale Avenue
City of Industry, CA 91716-0080
(626)968-5666 Fax(626)330-3861
FITTER
WIRE CONNECTORS
(BY OTHERS)
4" O.D. POLE OR
4" O.D. ARM TOP TENON
DATE
07/02/13
DATE
07/02/13
APPRVD PART NO.
KC
REV.
A
93046553
CATALOG NUMBER
INSTALLATION INSTRUCTIONS
SLVT H* / CF
TOP CLOSURE COVER
ASSEMBLY
(4) CAPTIVE SCREW
LAMP (BY OTHERS)
(REF)
DOOR SCREW
DOOR ASSEMBLY
(3) STAINLESS STEEL SET SCREW
FIXTURE INSTALLATION STEPS:
1) TURN POWER OFF.
2) MAKE WIRE CONNECTIONS FROM
INCOMING SUPPLY TO FIXTURE ASS'Y.
(NOTE: FIXTURE ASSEMBLY MUST BE
GROUNDED TO INCOMING EQUIPMENT
GROUND SUPPLY).
3) SLIP FITTER OVER TOP OF POLE. SECURE
FITTER WITH (3) STAINLESS STEEL SET SCREWS.
4) INSTALLATION COMPLETE.
FITTER
WIRE CONNECTORS
(BY OTHERS)
LAMP INSTALLATION STEPS:
1) TURN OFF POWER.
2) LOOSEN DOOR SCREW FROM DOOR ASSEMBLY.
3) OPEN DOOR ASSEMBLY.
4) INSTALL LAMP (BY OTHERS).
5) CLOSE DOOR ASSEMBLY AND
SECURE WITH DOOR SCREW.
6) INSTALLATION COMPLETE.
4" O.D. POLE OR
4" O.D. ARM TOP TENON
TO SERVICE BALLAST:
1) TURN OFF POWER.
2) LOOSEN (4) CAPTIVE SCREWS LOCATED AT
THE BOTTOM OF THE FIXTURE. OPEN TOP
CLOSURE COVER ASSEMBLY AND SET ASIDE.
3) INTERIOR OF THE HOUSING IS EXPOSED.
4) DISCONNECT WIRE CONNECTORS.
5) SERVICE BALLAST AS NEEDED.
6) TO RE-ASSEMBLE, REVERSE PROCEDURE.
16555 East Gale Avenue
City of Industry, CA 91745
(626)968-5666
DATE
APPRVD PART NO.
8/13/2010
DATE
REV.
A96496
CATALOG NUMBER
INSTALLATION INSTRUCTIONS
SLVTL & SLVTLDL
TOP CLOSURE COVER
ASSEMBLY
BALLAST COVER PLATE
COVER PLATE
(2) WING NUT
SCREW
(4) CAPTIVE SCREW
(2) HEX KEP NUT
FIXTURE INSTALLATION STEPS:
1) TURN POWER OFF.
2) MAKE WIRE CONNECTIONS FROM
INCOMING SUPPLY TO FIXTURE ASS'Y.
(NOTE: FIXTURE ASSEMBLY MUST BE
GROUNDED TO INCOMING EQUIPMENT
GROUND SUPPLY).
3) SLIP FITTER OVER TOP OF POLE. SECURE
FITTER WITH (3) STAINLESS STEEL SET SCREWS.
4) INSTALLATION COMPLETE.
LAMP (BY OTHERS)
LAMP INSTALLATION STEPS:
1) TURN OFF POWER.
2) LOOSEN (4) CAPTIVE SCREWS LOCATED AT
THE BOTTOM OF THE FIXTURE AND OPEN TOP
CLOSURE COVER ASSEMBLY AND SET ASIDE.
3) INTERIOR OF THE HOUSING IS EXPOSE.
4) REMOVE (2) WING NUTS AND COVER PLATE.
5) INSTALL LAMP (BY OTHERS).
6) TO RE-ASSEMBLE, REVERSE PROCEDURE.
(3) STAINLESS STEEL SET SCREW
FITTER
TO SERVICE BALLAST:
1) TURN OFF POWER.
2) LOOSEN (4) CAPTIVE SCREWS LOCATED AT
THE BOTTOM OF THE FIXTURE AND OPEN TOP
CLOSURE COVER ASSEMBLY AND SET ASIDE.
3) INTERIOR OF THE HOUSING IS EXPOSED.
4) REMOVE SCREW AND (2) HEX KEP NUTS.
5) LIFT BALLAST COVER PLATE. TURN UPSIDE DOWN
AND DISCONNECT WIRE CONNECTORS.
6) SERVICE BALLAST AS NEEDED.
7) TO RE-ASSEMBLE, REVERSE PROCEDURE.
16555 East Gale Avenue
City of Industry, CA 91745
(626)968-5666
WIRE CONNECTORS
(BY OTHERS)
4" O.D. POLE OR
4" O.D. ARM TOP TENON
DATE
DATE
NOTE:
DRAWING SHOWN
SLVTLDL OPTION.
APPRVD PART NO.
REV.
A96497