FINAL ADJUSTMENT AND REGULATING PROCEDURE
DELAYED
ACTION
VALVE
(OPTIONAL)
1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODY
AND FOOT ON DOOR AND FRAME.
BACKCHECK
VALVE
DELAYED ACTION
RANGE
1/4" SPRING POWER
ADJUSTMENT SCREW
CLOSING
SPEED VALVE
B
REGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.
USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISE
TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR
MOVEMENT.
FASTER
(+)
D
FOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE
3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THAT
SHOWN FOR MOUNTING THE CLOSER BODY.
B
REGULATING BACKCHECK
SARGENT 1430
SERIES CLOSER
SHOWN. (OTHER
SERIES SIMILAR)
SEE NOTE #1 BELOW FOR DIMENSION
INFORMATION. IF A DIMENSION LESS THAN
7/8" IS USED. THE DOOR STOP MUST BE CUT
TO CLEAR THE MORTISE NUT HEAD OR THE
MORTISE NUT HEAD MUST BE RECESSED.
(SEE ENLARGED VIEW "Y")
CLOSER MOUNTED ON
HINGE SIDE OF DOOR
E
+
NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREW
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)
281
INTERIOR DOORS
APPROXIMATE
EXTERIOR DOORS
DOOR WEIGHT (POUNDS)
FACTORY SET
80
110
1-5 CW
115
1-5 CCW
130
5-8 CW
150
155
8-13 CW
FACTORY SET
165
170
1-5 CW
13-15 CW
180
UP TO 19 CW AS REQ. 5 CW AND UP AS REQ.
NOTE: FOR 08 AND OLC TYPE ARMS MOUNTING
SEE DATA SHEETS ENCLOSED
DOOR STOP
MORTISE NUT HEAD
DOOR
DRILL 3/8" DIA.
HOLE FOR MORTISE
NUT BODY.
DRILL 1/4" DIA. HOLE
FOR MOUNTING SCREWS
*ADJUST SPRING POWER ACCORDING TO CHART
+
TOP JAMB
APPLICATION
(TYPE 25-O, 25-OZ
AND 25-OZA ARMS)
MOVE FOOT
PIVOT TO HOLE
NEAREST HINGE
+
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
USE
PAGE 2
FRAME
ADJUSTING FOOT FOR ADDITIONAL CLOSING POWER
(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)
HINGE EDGE OF DOOR
TURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTER
CLOCKWISE TO SPEED UP DOOR MOVEMENT
STANDARD & TOP JAMB APPLICATIONS
STANDARD APPLICATION
(TYPE 25-O ARM)
4. FOR DOORS 2-1/4" THICK: MORTISE NUT SHOWN FOR 1-3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.
DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTS
ARE TIGHTENED.
LATCHING
SPEED RANGE
COVER
“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGH
DELAYED ACTION RANGE
1
BACKCHECK
RANGE
TO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVE
CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE
CHECKING.
CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT IS
DAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.
NEVER USE BACKCHECK AS A DOOR STOP.
ALWAYS USE A DOOR STOP TO STOP THE DOOR.
SLOWER
(–)
281 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.
FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.
2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.
CLOSING SPEED
RANGE
LATCHING
SPEED
VALVE
A
MODEL 281 POWERGLIDE SERIES
INSTRUCTIONS FOR INSTALLING SARGENT DOOR
CLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)
USING MORTISE NUTS WITH SARGENT DOOR CLOSER
-
INCREASE
POWER
DECREASE
POWER
CLOCKWISE
(CW)
COUNTER CLOCKWISE
(CCW)
1/4" ALLEN SPRING POWER
ADJUSTING SCREW
SARGENT 351 SERIES SHOWN
LEFT
HAND DOOR
1/8"
SHORTEN MORTISE
NUT BODY TO
THIS LENGTH
5/8" DIA. HOLE
STOP (PUSH) SIDE
CLOSER MOUNTED ON FRAME
ON STOP SIDE OF DOOR
FRAME
INSTALL COVER WITH TWO SCREWS AS SHOWN.
PULL
HINGE SIDE
PULL
HINGE SIDE
RIGHT
HAND DOOR
STOP (PUSH) SIDE
USE
PAGE 3
DOOR
STOP
PARALLEL APPLICATION ONLY
DOOR
351 DOOR CLOSER SHOWN
(TRACK ASSEMBLY
MOUNTING IS SIMILAR)
1/4" DIA.
DRILLED HOLE
#12-24 THREAD
MORTISE NUT
9/16"
DIA.
MORTISE NUT
HEAD
3/8" DIA. HOLE
PARALLEL ARM
APPLICATION
(TYPE 25-P9)
VIEW "Y"
7/64"
USE
PAGE 4
1-11/16" FOR 1-3/4" THICK DOOR
1-5/16" FOR 1-3/8" THICK DOOR
(SEE NOTE #4 FOR 2-1/4" THICK DOORS)
INSERT IS REMOVABLE.
PLACE IN UNUSED OPENING.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
5
CLOSER MOUNTED ON
STOP SIDE OF DOOR
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
6
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY) INTERIOR DOORS
APPROXIMATE
281
DOOR WEIGHT (POUNDS)
EXTERIOR DOORS
80
2-7 CW
110
115
7-11 CW
1-5 CCW
130
150
FACTORY SET
11-15 CW
155
165
170
15-17 CW
1-8 CW
180
UP TO 19 CW AS REQ. 8 CW AND UP AS REQ.
*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGS
ARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNING
SPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREW
COUNTERCLOCKWISE.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
1
281 STANDARD APPLICATION FOR INSTRUCTIONS
281 TOP JAMB APPLICATION INSTRUCTIONS
IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING
ARM
TYPE
MOUNTING
MAX. DOOR
OPENING
IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING
DIM.
A
DIM.
B
DIM.
A
REVEAL
DEPTH
ARM
TYPE
MAX. DOOR
OPENING
MAX. DOOR
OPENING
DIM. "B"
REGULAR
ARM NO
HOLDER
STANDARD
7"
12-1/8"
5"
10-1/8"
"A"
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT
HEAD MACHINE SCREWS
2"
1-1/4"
1
RIGHT HAND DOOR SHOWN. LEFT HAND
DOOR OPPOSITE.
0" TO 2"
9-5/16"
“OZ” ARM
2-1/8" TO 5"
10-1/8"
“OZA” ARM
5-1/8" TO 5"
10-15/16"
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
1"
DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE
NUTS WHEN REQUIRED.
ALTERNATE MOUNTING IS
RECOMMENDED FOR ADA
COMPLIANT DOORS
CL OF HINGE PIVOT:
BUTTS, OFFSET PIVOTS,
SWING CLEAR, CENTER HUNG
OR INVISIBLE HINGES
5/8"
FRAME
TOP
OF
DOOR
10-3/8"
#12 X 1-1/2" WOOD SCREWS
OR #12-24 X 5/8 FLAT HEAD
MACHINE SCREW
10-3/8"
3-5/8"
7/8"
2
“O” ARM
1
LEFT HAND DOOR SHOWN, RIGHT
HAND DOOR OPPOSITE.
2
THESE DIMENSIONS MAYBE REDUCED TO 3/8"
MIN. IF RAIL ON TOP CASING IS NARROW OR
LOW CEILING CONDITION EXISTS. CLOSER
FOOT SHOULD BE MOVED ACCORDINGLY.
1
3
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
2
DIM.
ALTERNATE
281 PARALLEL ARM APPLICATION INSTRUCTIONS
4-1/2"
10-1/2"
HINGE PIVOT:
BUTT, OFFSET PIVOTS, SWING CLEAR,
CENTERHUNG OR INVISIBLE HINGES
2-1/2"
1-1/4"
1/2"
7-5/8"
DOOR
LEFT HAND DOOR SHOWN. RIGHT HAND
DOOR DIMENSION OPPOSITE.
7/8"
DRILL & TAP AND USE SCREWS PROVIDED OR USE
MORTISE NUTS WHEN REQUIRED.
TOP VIEW
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT HEAD
MACHINE SCREWS
DO NOT USE THIS MOUNTING FOR
“SWING CLEAR” HINGES.
5/16"
DIM. B
3
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
4
MAY BE REDUCED BY 1/2" TO AVOID
DOOR TRIM.
DIM. A
STOP
CL OF BRACKET
1"
DIM.
"A"
USE MOUNTING BRACKET
AS DRILL THRU TEMPLATE
TOP OF
DOOR
USE MOUNTING BRACKET
AS A DRILL-THRU TEMPLATE
1-5/8"
A
TOP OF
DOOR
3"
DRILL & TAP AND USE SCREWS PROVIDED OR USE
MORTISE NUTS WHEN REQUIRED.
2"
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT HEAD
MACHINE SCREWS
1"
CL OF PIVOT
INSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS AND
INSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.
DIM.
B
1-5/8"
10-3/8"
REMOVE BACKING FROM SELF ADHESIVE TAPE AND
USE BRACKET AS DRILL THROUGH TEMPLATE.
HINGE
A
DIM.
A
INSTALL MOUNTING BRACKET WITH ARROW POINTING DOWN FOR BOTH RH & LH DOORS AND
INSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.
B
ATTACH FOOT TO DOOR WITH
PIVOT AWAY FROM HINGE.
A
CL OF HINGE PIVOT
INSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS
AND INSTALL CLOSER WITH SPRING ADJUSTING SCREW TOWARDS HINGE.
B
ATTACH FOOT BRACKET TO FRAME STOP.
RIGHT HAND
DOOR SHOWN
RIGHT HAND
DOOR SHOWN
C
RIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)
PIVOT
C
P3 OR P3A
BRACKET
INSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN.
INSERT ROD END INTO MAIN ARM AND TIGHTEN ARM SCREW.
(SARGENT
#590 SHOWN)
P4 OR P4A
BRACKET
INDEX MARK
ON SPINDLE
MAIN ARM
LEFT HAND
DOOR
5
4
OPTIONAL ARMS FOR MOUNTING. SEE DATA
SHEET ENCLOSED.
5
MAIN
ARM
4
2
3
1
1
ROD
2
ARM
SCREW
INDEX MARK
ON SPINDLE
RIGHT HAND
DOOR
3
5
MAIN
ARM
INDEX
MARK
ON
SPINDLE
4
2
C
RIGHT HAND
DOOR SHOWN
ATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW AND
WASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.
3
1
B
ATTACH FOOT TO FRAME WITH PIVOT
AWAY FROM HINGE.
POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE
FOR FLUSH FRAME
AND DOOR CONDITIONS
SWIVEL ARM
CAUTION: DOOR CLOSER WILL NOT OPERATE
PROPERLY IF MAIN ARM IS NOT INDEXED CORRECTLY.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
2
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
3
FOR USE WITH OVERHEAD
DOOR HOLDERS
P4A BRACKET IS USED
WITH OVERHEAD HOLDERS
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
4
281 STANDARD APPLICATION FOR INSTRUCTIONS
281 TOP JAMB APPLICATION INSTRUCTIONS
IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING
ARM
TYPE
MOUNTING
MAX. DOOR
OPENING
IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING
DIM.
A
DIM.
B
DIM.
A
REVEAL
DEPTH
ARM
TYPE
MAX. DOOR
OPENING
MAX. DOOR
OPENING
DIM. "B"
REGULAR
ARM NO
HOLDER
STANDARD
7"
12-1/8"
5"
10-1/8"
"A"
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT
HEAD MACHINE SCREWS
2"
1-1/4"
1
RIGHT HAND DOOR SHOWN. LEFT HAND
DOOR OPPOSITE.
0" TO 2"
9-5/16"
“OZ” ARM
2-1/8" TO 5"
10-1/8"
“OZA” ARM
5-1/8" TO 5"
10-15/16"
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
1"
DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE
NUTS WHEN REQUIRED.
ALTERNATE MOUNTING IS
RECOMMENDED FOR ADA
COMPLIANT DOORS
CL OF HINGE PIVOT:
BUTTS, OFFSET PIVOTS,
SWING CLEAR, CENTER HUNG
OR INVISIBLE HINGES
5/8"
FRAME
TOP
OF
DOOR
10-3/8"
#12 X 1-1/2" WOOD SCREWS
OR #12-24 X 5/8 FLAT HEAD
MACHINE SCREW
10-3/8"
3-5/8"
7/8"
2
“O” ARM
1
LEFT HAND DOOR SHOWN, RIGHT
HAND DOOR OPPOSITE.
2
THESE DIMENSIONS MAYBE REDUCED TO 3/8"
MIN. IF RAIL ON TOP CASING IS NARROW OR
LOW CEILING CONDITION EXISTS. CLOSER
FOOT SHOULD BE MOVED ACCORDINGLY.
1
3
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
2
DIM.
ALTERNATE
281 PARALLEL ARM APPLICATION INSTRUCTIONS
4-1/2"
10-1/2"
HINGE PIVOT:
BUTT, OFFSET PIVOTS, SWING CLEAR,
CENTERHUNG OR INVISIBLE HINGES
2-1/2"
1-1/4"
1/2"
7-5/8"
DOOR
LEFT HAND DOOR SHOWN. RIGHT HAND
DOOR DIMENSION OPPOSITE.
7/8"
DRILL & TAP AND USE SCREWS PROVIDED OR USE
MORTISE NUTS WHEN REQUIRED.
TOP VIEW
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT HEAD
MACHINE SCREWS
DO NOT USE THIS MOUNTING FOR
“SWING CLEAR” HINGES.
5/16"
DIM. B
3
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
4
MAY BE REDUCED BY 1/2" TO AVOID
DOOR TRIM.
DIM. A
STOP
CL OF BRACKET
1"
DIM.
"A"
USE MOUNTING BRACKET
AS DRILL THRU TEMPLATE
TOP OF
DOOR
USE MOUNTING BRACKET
AS A DRILL-THRU TEMPLATE
1-5/8"
A
TOP OF
DOOR
3"
DRILL & TAP AND USE SCREWS PROVIDED OR USE
MORTISE NUTS WHEN REQUIRED.
2"
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT HEAD
MACHINE SCREWS
1"
CL OF PIVOT
INSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS AND
INSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.
DIM.
B
1-5/8"
10-3/8"
REMOVE BACKING FROM SELF ADHESIVE TAPE AND
USE BRACKET AS DRILL THROUGH TEMPLATE.
HINGE
A
DIM.
A
INSTALL MOUNTING BRACKET WITH ARROW POINTING DOWN FOR BOTH RH & LH DOORS AND
INSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.
B
ATTACH FOOT TO DOOR WITH
PIVOT AWAY FROM HINGE.
A
CL OF HINGE PIVOT
INSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS
AND INSTALL CLOSER WITH SPRING ADJUSTING SCREW TOWARDS HINGE.
B
ATTACH FOOT BRACKET TO FRAME STOP.
RIGHT HAND
DOOR SHOWN
RIGHT HAND
DOOR SHOWN
C
RIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)
PIVOT
C
P3 OR P3A
BRACKET
INSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN.
INSERT ROD END INTO MAIN ARM AND TIGHTEN ARM SCREW.
(SARGENT
#590 SHOWN)
P4 OR P4A
BRACKET
INDEX MARK
ON SPINDLE
MAIN ARM
LEFT HAND
DOOR
5
4
OPTIONAL ARMS FOR MOUNTING. SEE DATA
SHEET ENCLOSED.
5
MAIN
ARM
4
2
3
1
1
ROD
2
ARM
SCREW
INDEX MARK
ON SPINDLE
RIGHT HAND
DOOR
3
5
MAIN
ARM
INDEX
MARK
ON
SPINDLE
4
2
C
RIGHT HAND
DOOR SHOWN
ATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW AND
WASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.
3
1
B
ATTACH FOOT TO FRAME WITH PIVOT
AWAY FROM HINGE.
POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE
FOR FLUSH FRAME
AND DOOR CONDITIONS
SWIVEL ARM
CAUTION: DOOR CLOSER WILL NOT OPERATE
PROPERLY IF MAIN ARM IS NOT INDEXED CORRECTLY.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
2
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
3
FOR USE WITH OVERHEAD
DOOR HOLDERS
P4A BRACKET IS USED
WITH OVERHEAD HOLDERS
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
4
281 STANDARD APPLICATION FOR INSTRUCTIONS
281 TOP JAMB APPLICATION INSTRUCTIONS
IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING
ARM
TYPE
MOUNTING
MAX. DOOR
OPENING
IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING
DIM.
A
DIM.
B
DIM.
A
REVEAL
DEPTH
ARM
TYPE
MAX. DOOR
OPENING
MAX. DOOR
OPENING
DIM. "B"
REGULAR
ARM NO
HOLDER
STANDARD
7"
12-1/8"
5"
10-1/8"
"A"
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT
HEAD MACHINE SCREWS
2"
1-1/4"
1
RIGHT HAND DOOR SHOWN. LEFT HAND
DOOR OPPOSITE.
0" TO 2"
9-5/16"
“OZ” ARM
2-1/8" TO 5"
10-1/8"
“OZA” ARM
5-1/8" TO 5"
10-15/16"
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
1"
DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE
NUTS WHEN REQUIRED.
ALTERNATE MOUNTING IS
RECOMMENDED FOR ADA
COMPLIANT DOORS
CL OF HINGE PIVOT:
BUTTS, OFFSET PIVOTS,
SWING CLEAR, CENTER HUNG
OR INVISIBLE HINGES
5/8"
FRAME
TOP
OF
DOOR
10-3/8"
#12 X 1-1/2" WOOD SCREWS
OR #12-24 X 5/8 FLAT HEAD
MACHINE SCREW
10-3/8"
3-5/8"
7/8"
2
“O” ARM
1
LEFT HAND DOOR SHOWN, RIGHT
HAND DOOR OPPOSITE.
2
THESE DIMENSIONS MAYBE REDUCED TO 3/8"
MIN. IF RAIL ON TOP CASING IS NARROW OR
LOW CEILING CONDITION EXISTS. CLOSER
FOOT SHOULD BE MOVED ACCORDINGLY.
1
3
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
2
DIM.
ALTERNATE
281 PARALLEL ARM APPLICATION INSTRUCTIONS
4-1/2"
10-1/2"
HINGE PIVOT:
BUTT, OFFSET PIVOTS, SWING CLEAR,
CENTERHUNG OR INVISIBLE HINGES
2-1/2"
1-1/4"
1/2"
7-5/8"
DOOR
LEFT HAND DOOR SHOWN. RIGHT HAND
DOOR DIMENSION OPPOSITE.
7/8"
DRILL & TAP AND USE SCREWS PROVIDED OR USE
MORTISE NUTS WHEN REQUIRED.
TOP VIEW
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT HEAD
MACHINE SCREWS
DO NOT USE THIS MOUNTING FOR
“SWING CLEAR” HINGES.
5/16"
DIM. B
3
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
4
MAY BE REDUCED BY 1/2" TO AVOID
DOOR TRIM.
DIM. A
STOP
CL OF BRACKET
1"
DIM.
"A"
USE MOUNTING BRACKET
AS DRILL THRU TEMPLATE
TOP OF
DOOR
USE MOUNTING BRACKET
AS A DRILL-THRU TEMPLATE
1-5/8"
A
TOP OF
DOOR
3"
DRILL & TAP AND USE SCREWS PROVIDED OR USE
MORTISE NUTS WHEN REQUIRED.
2"
#12 x 1-1/2 WOOD SCREWS
OR #12-24 x 5/8 FLAT HEAD
MACHINE SCREWS
1"
CL OF PIVOT
INSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS AND
INSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.
DIM.
B
1-5/8"
10-3/8"
REMOVE BACKING FROM SELF ADHESIVE TAPE AND
USE BRACKET AS DRILL THROUGH TEMPLATE.
HINGE
A
DIM.
A
INSTALL MOUNTING BRACKET WITH ARROW POINTING DOWN FOR BOTH RH & LH DOORS AND
INSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.
B
ATTACH FOOT TO DOOR WITH
PIVOT AWAY FROM HINGE.
A
CL OF HINGE PIVOT
INSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS
AND INSTALL CLOSER WITH SPRING ADJUSTING SCREW TOWARDS HINGE.
B
ATTACH FOOT BRACKET TO FRAME STOP.
RIGHT HAND
DOOR SHOWN
RIGHT HAND
DOOR SHOWN
C
RIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)
PIVOT
C
P3 OR P3A
BRACKET
INSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN.
INSERT ROD END INTO MAIN ARM AND TIGHTEN ARM SCREW.
(SARGENT
#590 SHOWN)
P4 OR P4A
BRACKET
INDEX MARK
ON SPINDLE
MAIN ARM
LEFT HAND
DOOR
5
4
OPTIONAL ARMS FOR MOUNTING. SEE DATA
SHEET ENCLOSED.
5
MAIN
ARM
4
2
3
1
1
ROD
2
ARM
SCREW
INDEX MARK
ON SPINDLE
RIGHT HAND
DOOR
3
5
MAIN
ARM
INDEX
MARK
ON
SPINDLE
4
2
C
RIGHT HAND
DOOR SHOWN
ATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW AND
WASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.
3
1
B
ATTACH FOOT TO FRAME WITH PIVOT
AWAY FROM HINGE.
POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE
FOR FLUSH FRAME
AND DOOR CONDITIONS
SWIVEL ARM
CAUTION: DOOR CLOSER WILL NOT OPERATE
PROPERLY IF MAIN ARM IS NOT INDEXED CORRECTLY.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
2
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
3
FOR USE WITH OVERHEAD
DOOR HOLDERS
P4A BRACKET IS USED
WITH OVERHEAD HOLDERS
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
4
FINAL ADJUSTMENT AND REGULATING PROCEDURE
DELAYED
ACTION
VALVE
(OPTIONAL)
1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODY
AND FOOT ON DOOR AND FRAME.
BACKCHECK
VALVE
DELAYED ACTION
RANGE
1/4" SPRING POWER
ADJUSTMENT SCREW
CLOSING
SPEED VALVE
B
REGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.
USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISE
TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR
MOVEMENT.
FASTER
(+)
D
FOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE
3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THAT
SHOWN FOR MOUNTING THE CLOSER BODY.
B
REGULATING BACKCHECK
SARGENT 1430
SERIES CLOSER
SHOWN. (OTHER
SERIES SIMILAR)
SEE NOTE #1 BELOW FOR DIMENSION
INFORMATION. IF A DIMENSION LESS THAN
7/8" IS USED. THE DOOR STOP MUST BE CUT
TO CLEAR THE MORTISE NUT HEAD OR THE
MORTISE NUT HEAD MUST BE RECESSED.
(SEE ENLARGED VIEW "Y")
CLOSER MOUNTED ON
HINGE SIDE OF DOOR
E
+
NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREW
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)
281
INTERIOR DOORS
APPROXIMATE
EXTERIOR DOORS
DOOR WEIGHT (POUNDS)
FACTORY SET
80
110
1-5 CW
115
1-5 CCW
130
5-8 CW
150
155
8-13 CW
FACTORY SET
165
170
1-5 CW
13-15 CW
180
UP TO 19 CW AS REQ. 5 CW AND UP AS REQ.
NOTE: FOR 08 AND OLC TYPE ARMS MOUNTING
SEE DATA SHEETS ENCLOSED
DOOR STOP
MORTISE NUT HEAD
DOOR
DRILL 3/8" DIA.
HOLE FOR MORTISE
NUT BODY.
DRILL 1/4" DIA. HOLE
FOR MOUNTING SCREWS
*ADJUST SPRING POWER ACCORDING TO CHART
+
TOP JAMB
APPLICATION
(TYPE 25-O, 25-OZ
AND 25-OZA ARMS)
MOVE FOOT
PIVOT TO HOLE
NEAREST HINGE
+
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
USE
PAGE 2
FRAME
ADJUSTING FOOT FOR ADDITIONAL CLOSING POWER
(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)
HINGE EDGE OF DOOR
TURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTER
CLOCKWISE TO SPEED UP DOOR MOVEMENT
STANDARD & TOP JAMB APPLICATIONS
STANDARD APPLICATION
(TYPE 25-O ARM)
4. FOR DOORS 2-1/4" THICK: MORTISE NUT SHOWN FOR 1-3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.
DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTS
ARE TIGHTENED.
LATCHING
SPEED RANGE
COVER
“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGH
DELAYED ACTION RANGE
1
BACKCHECK
RANGE
TO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVE
CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE
CHECKING.
CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT IS
DAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.
NEVER USE BACKCHECK AS A DOOR STOP.
ALWAYS USE A DOOR STOP TO STOP THE DOOR.
SLOWER
(–)
281 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.
FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.
2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.
CLOSING SPEED
RANGE
LATCHING
SPEED
VALVE
A
MODEL 281 POWERGLIDE SERIES
INSTRUCTIONS FOR INSTALLING SARGENT DOOR
CLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)
USING MORTISE NUTS WITH SARGENT DOOR CLOSER
-
INCREASE
POWER
DECREASE
POWER
CLOCKWISE
(CW)
COUNTER CLOCKWISE
(CCW)
1/4" ALLEN SPRING POWER
ADJUSTING SCREW
SARGENT 351 SERIES SHOWN
LEFT
HAND DOOR
1/8"
SHORTEN MORTISE
NUT BODY TO
THIS LENGTH
5/8" DIA. HOLE
STOP (PUSH) SIDE
CLOSER MOUNTED ON FRAME
ON STOP SIDE OF DOOR
FRAME
INSTALL COVER WITH TWO SCREWS AS SHOWN.
PULL
HINGE SIDE
PULL
HINGE SIDE
RIGHT
HAND DOOR
STOP (PUSH) SIDE
USE
PAGE 3
DOOR
STOP
PARALLEL APPLICATION ONLY
DOOR
351 DOOR CLOSER SHOWN
(TRACK ASSEMBLY
MOUNTING IS SIMILAR)
1/4" DIA.
DRILLED HOLE
#12-24 THREAD
MORTISE NUT
9/16"
DIA.
MORTISE NUT
HEAD
3/8" DIA. HOLE
PARALLEL ARM
APPLICATION
(TYPE 25-P9)
VIEW "Y"
7/64"
USE
PAGE 4
1-11/16" FOR 1-3/4" THICK DOOR
1-5/16" FOR 1-3/8" THICK DOOR
(SEE NOTE #4 FOR 2-1/4" THICK DOORS)
INSERT IS REMOVABLE.
PLACE IN UNUSED OPENING.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
5
CLOSER MOUNTED ON
STOP SIDE OF DOOR
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
6
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY) INTERIOR DOORS
APPROXIMATE
281
DOOR WEIGHT (POUNDS)
EXTERIOR DOORS
80
2-7 CW
110
115
7-11 CW
1-5 CCW
130
150
FACTORY SET
11-15 CW
155
165
170
15-17 CW
1-8 CW
180
UP TO 19 CW AS REQ. 8 CW AND UP AS REQ.
*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGS
ARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNING
SPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREW
COUNTERCLOCKWISE.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
1
FINAL ADJUSTMENT AND REGULATING PROCEDURE
DELAYED
ACTION
VALVE
(OPTIONAL)
1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODY
AND FOOT ON DOOR AND FRAME.
BACKCHECK
VALVE
DELAYED ACTION
RANGE
1/4" SPRING POWER
ADJUSTMENT SCREW
CLOSING
SPEED VALVE
B
REGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.
USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISE
TO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOOR
MOVEMENT.
FASTER
(+)
D
FOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE
3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THAT
SHOWN FOR MOUNTING THE CLOSER BODY.
B
REGULATING BACKCHECK
SARGENT 1430
SERIES CLOSER
SHOWN. (OTHER
SERIES SIMILAR)
SEE NOTE #1 BELOW FOR DIMENSION
INFORMATION. IF A DIMENSION LESS THAN
7/8" IS USED. THE DOOR STOP MUST BE CUT
TO CLEAR THE MORTISE NUT HEAD OR THE
MORTISE NUT HEAD MUST BE RECESSED.
(SEE ENLARGED VIEW "Y")
CLOSER MOUNTED ON
HINGE SIDE OF DOOR
E
+
NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREW
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)
281
INTERIOR DOORS
APPROXIMATE
EXTERIOR DOORS
DOOR WEIGHT (POUNDS)
FACTORY SET
80
110
1-5 CW
115
1-5 CCW
130
5-8 CW
150
155
8-13 CW
FACTORY SET
165
170
1-5 CW
13-15 CW
180
UP TO 19 CW AS REQ. 5 CW AND UP AS REQ.
NOTE: FOR 08 AND OLC TYPE ARMS MOUNTING
SEE DATA SHEETS ENCLOSED
DOOR STOP
MORTISE NUT HEAD
DOOR
DRILL 3/8" DIA.
HOLE FOR MORTISE
NUT BODY.
DRILL 1/4" DIA. HOLE
FOR MOUNTING SCREWS
*ADJUST SPRING POWER ACCORDING TO CHART
+
TOP JAMB
APPLICATION
(TYPE 25-O, 25-OZ
AND 25-OZA ARMS)
MOVE FOOT
PIVOT TO HOLE
NEAREST HINGE
+
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
USE
PAGE 2
FRAME
ADJUSTING FOOT FOR ADDITIONAL CLOSING POWER
(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)
HINGE EDGE OF DOOR
TURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTER
CLOCKWISE TO SPEED UP DOOR MOVEMENT
STANDARD & TOP JAMB APPLICATIONS
STANDARD APPLICATION
(TYPE 25-O ARM)
4. FOR DOORS 2-1/4" THICK: MORTISE NUT SHOWN FOR 1-3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.
DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTS
ARE TIGHTENED.
LATCHING
SPEED RANGE
COVER
“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGH
DELAYED ACTION RANGE
1
BACKCHECK
RANGE
TO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVE
CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE
CHECKING.
CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT IS
DAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.
NEVER USE BACKCHECK AS A DOOR STOP.
ALWAYS USE A DOOR STOP TO STOP THE DOOR.
SLOWER
(–)
281 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.
FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.
2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.
CLOSING SPEED
RANGE
LATCHING
SPEED
VALVE
A
MODEL 281 POWERGLIDE SERIES
INSTRUCTIONS FOR INSTALLING SARGENT DOOR
CLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)
USING MORTISE NUTS WITH SARGENT DOOR CLOSER
-
INCREASE
POWER
DECREASE
POWER
CLOCKWISE
(CW)
COUNTER CLOCKWISE
(CCW)
1/4" ALLEN SPRING POWER
ADJUSTING SCREW
SARGENT 351 SERIES SHOWN
LEFT
HAND DOOR
1/8"
SHORTEN MORTISE
NUT BODY TO
THIS LENGTH
5/8" DIA. HOLE
STOP (PUSH) SIDE
CLOSER MOUNTED ON FRAME
ON STOP SIDE OF DOOR
FRAME
INSTALL COVER WITH TWO SCREWS AS SHOWN.
PULL
HINGE SIDE
PULL
HINGE SIDE
RIGHT
HAND DOOR
STOP (PUSH) SIDE
USE
PAGE 3
DOOR
STOP
PARALLEL APPLICATION ONLY
DOOR
351 DOOR CLOSER SHOWN
(TRACK ASSEMBLY
MOUNTING IS SIMILAR)
1/4" DIA.
DRILLED HOLE
#12-24 THREAD
MORTISE NUT
9/16"
DIA.
MORTISE NUT
HEAD
3/8" DIA. HOLE
PARALLEL ARM
APPLICATION
(TYPE 25-P9)
VIEW "Y"
7/64"
USE
PAGE 4
1-11/16" FOR 1-3/4" THICK DOOR
1-5/16" FOR 1-3/8" THICK DOOR
(SEE NOTE #4 FOR 2-1/4" THICK DOORS)
INSERT IS REMOVABLE.
PLACE IN UNUSED OPENING.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
5
CLOSER MOUNTED ON
STOP SIDE OF DOOR
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
6
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY) INTERIOR DOORS
APPROXIMATE
281
DOOR WEIGHT (POUNDS)
EXTERIOR DOORS
80
2-7 CW
110
115
7-11 CW
1-5 CCW
130
150
FACTORY SET
11-15 CW
155
165
170
15-17 CW
1-8 CW
180
UP TO 19 CW AS REQ. 8 CW AND UP AS REQ.
*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGS
ARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNING
SPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREW
COUNTERCLOCKWISE.
Copyright © 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7278E
1