Communications Technology
The training systems for communications technology (communications trainer) encompass topics from the area
of high-frequency communications (airborne and wire-conducted signals), network technology and
telecommunications.
Basic modules of the telecommunications technology
Basic modules of the telecommunications technology
Lucas Nülle GmbH
Page 1/113
www.lucas-nuelle.com
List of articles:
Pos.
Product name
Bestell-Nr.
1 Course Telecommunications 1: Quadripoles and filters
SO4204-9A
Anz.
1
Includes:
1 Experiment card with RC high-pass and low-pass filters,
RC combinations configurable by jumpers
1 Experiment card with band-pass filter, consisting of 2
capacitively coupled parallel resonant circuits
1 Experiment card with band-pass and band-cut filters
1 Experiment card with series and parallel resonant circuits
and parallel resonant circuit with tuning
CD-ROM with Labsoft and course software
Course contents:
Introduction to the term transmission function, phase
response and limiting of filters
Introduction to representing transmission functions in the
complex plane
Determination of transmission function, phase response and
cut-off frequencies of high-pass and low-pass filters by
measurement (Bode plot)
Determination of transmission function, band width and
median frequency of band-pass filters by measurement
(Bode plot)
Introduction to the terms transmission function, band width,
quality and resonant frequency of resonant circuits
Introduction to representing transmission functions of
resonant circuits in the complex plane
Determination of transmission function, phase response and
resonant frequency of resonant circuits filters by
measurement (Bode plot)
Determination of band width and quality of resonant circuits
by measurement
Determination of tunable range of a parallel resonant circuit
with varicap diode tuning by measurement
Course duration: 5.0 h approx.
Lucas Nülle GmbH
Page 2/113
www.lucas-nuelle.com
2 Course Telecommunications 11: Active filter with operational
amplifiers
SO4204-9B
1
Includes:
1 Experiment card with active low-pass 2-nd and 4-th order
1 Experiment card with active high-pass 2-nd and 4-th order
1 Experiment card with active band-pass and band-cut 2-nd
order
Multimeter Multi 18S
CD-ROM with Labsoft and course software
Course contents:
Definition filter. Passive and active filter
Bode plot
Types of filters. High-pass, low-pass, band-pass and bandcut
Order, slope, maxphase shift
Tolerance pattern. Upper and lower cut-off frequency,
attenuation
Filter aproximations. Bessel-, Butterworth- and Tshebyshefffilter
Characteristic in the time domain. Delay time, rise time,
transitive zone, stationary zone
Low-pass and high-pass filter 2-nd order
Low-pass and high-pass filter 4-th order
Band-pass and band-cut 2-nd order
Course duration: 5,0 h approx.
Lucas Nülle GmbH
Page 3/113
www.lucas-nuelle.com
3 Course - Electronics 5: Operational amplifiers
SO4204-5M
1
Includes:
1 Experiment card with inverting and non-inverting op-amp
circuits
1 Experiment card with comparator and Schmitt trigger circuit
with adjustable reference voltage
1 Experiment card for the assembly of various operational
amplifier circuits (active filter, precision rectifier, derivativeaction element, integral-action element, constant current
source, precision voltage source) with adjustable reference
voltage and variable load resistor
CD-ROM with Labsoft browser and course software
Course contents:
Introduction to the design and function of operational
amplifiers
Circuit diagram and basic circuit types for operational
amplifiers (impedance converters, adders, comparators,
Schmitt triggers)
Determination of the characteristic and limiting values of an
operational amplifier by measurement
Investigation of DC and AC response of inverting and noninverting op-amp circuits
Set-up and measurements of precision voltage source and
constant current source
Set-up and measurements of adder and subtractor circuits
Set-up and measurements of integral-action and derivativeaction circuits
Measurements on a comparator circuit
Investigating the switching response of a Schmitt trigger as a
function of reference voltages
Set-up and measurements of active filter circuits
Set-up of a precision rectifier and examination using
measurements
Fault simulation (6 simulated faults activated by relay)
Course duration 5.5 h approx. (fault finding 0.5 h approx.)
Lucas Nülle GmbH
Page 4/113
www.lucas-nuelle.com
4 Course - Digital electronics 4: Converter circuits
SO4204-6B
1
Includes:
1 Experiment card with 1 D/A converter with weighted
resistors and 1 D/A converter with R-2R network, built using
discrete components
1 Experiment card with 1 A/D converter using single-/dualslope method and 1 A/D converter using parallel method
(flash converter), built using discrete components
1 Experiment card with 1 V/f converter and 1 f/V converter
CD-ROM with Labsoft browser and course software
Course contents:
Basic parameters for converter circuits: resolution, linearity,
speed
Introduction to the design and function of a D/A converter with
an R/2R network
Recording static and dynamic characteristics for a D/A
converter with R-2R network
Introduction to the design and function of a D/A-converter with
weighted resistors
Recording static and dynamic characteristics for a D/A
converter with weighted resistors
Investigation of an applied D/A converter circuit
Basic terminology for digital data acquisition: sampling,
sampling theorem, signal reconstruction, aliasing
Introduction to the design and function of a flash A/D converter
Introduction to the design and function of an A/D converter
using the "single-/dual-slope" method
Introduction to the design and function of sigma-deltaconverters
Recording the characteristic for an A/D converter
Measuring internal signals in an A/D converter
Introduction to the design and function of V/f and f/V
converters
Adjusting the reference voltage for V/f and f/V converters
Recording the characteristic of V/f and f/V converters
Measuring internal signals in V/f and f/V converters
Investigating V/f/f/V converter circuits
Fault simulation (5 simulated faults activated by relay)
Course duration 5 h approx. (fault finding 1 h approx.)
Lucas Nülle GmbH
Page 5/113
www.lucas-nuelle.com
Additionally required:
The UniTrain-I system is a computer-based training and experimentation system for vocational and further
training and education in the areas of basic and advanced electrical engineering and electronics. Its multimedia
courses combine cognitive and hands-on (haptic) training units into a comprehensive unified concept,
specifically enabling students to acquire skills in the handling of equipment. Starting with basic courses and
advancing to cover a huge variety of electrical engineering and electronics topics, a wide range of multimedia
courses is available for study in school or in professional and advanced training courses. The UniTrain-I system
is completely self-contained and can be used anywhere at any time. The multimedia learning environment the
system provides high degrees of motivation, and maximum learning effectiveness in laboratories, at work or at
home. It thus becomes a guarantor for effective and efficient study. Access to the multimedia courses and
control of virtual instruments and experiment hardware is provided by LabSoft, the system's open experiment
platform. The courses teach the theoretical building blocks and provide experiments to be carried out using the
course-specific experiment hardware. The intelligent measurement interface supplies the analog and digital
measuring and control I/O and represents, in combination with the system's virtual instruments, a high quality
item of laboratory equipment. In addition, students' progress can be monitored and electronically documented on
the basis of fault finding experiments with faults simulated by the hardware as well as tests of knowledge. The
electrical and electronic circuits needed for the experiments are connected to the system with the aid of an
Experimenter module.
Lucas Nülle GmbH
Page 6/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
5 UniTrain Interface with virtual instruments (basic VI)
CO4203-2A
Anz.
1
The UniTrain Interface is the central unit of the UniTrain system. It
incorporates all inputs and outputs, switches, power and signal
sources and measurement circuitry needed to perform experiments.
The Interface is controlled via the connected PC.
Equipment:
32-bit processor with storage memory for measurements
USB interfaces, transfer rate 12 Mbits/s
WLAN/WiFi interface, 2.4 GHz, IEEE 802.11 b/g/n
Simultaneous connection of any number of Experimenters via
serial bus system
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front panel
Suitable for accommodating in training panel frames for DIN
A4 training panels
Designed for connection of 2-mm safety measuring leads
Multi-coloured LEDs for displaying status
Adjustable analog output, +/-10 V, 0.2 A, DC – 5 MHz, via BNC
and 2-mm sockets
4 Analog differential amplifier inputs with 10 MHz band width,
safe for voltages up to 100 V, sampling rate 100 mega
samples, 9 measuring ranges, memory depth 4 x 8 k x 10
bits, inputs via BNC (2 inputs) or 2-mm sockets (4 inputs)
2 Analog inputs for current measurement, overcurrentprotected up to 5 A, sampling rate 250 kilo samples, 2
measuring ranges, resolution 12 bits, connection via 2-mm
sockets
16-bit digital signal output, of which 8 bits are accessed via 2mm sockets, TTL/CMOS, clock frequency 0 – 100 kHz, electric
strength +/- 15 V
16-bit digital signal input, of which 8 bits are accessed via 2mm sockets, memory depth 16 bit x 2 k, TTL/CMOS, sampling
rate 0 – 100 kHz, electric strength +/- 15 V,
8 Relays, 24 V DC/1 A, of which 4 are accessed via 2-mm
sockets
Dimensions: 29.6 x 19 x 8.6 cm
External power supply with wide range input 100-264 V, 47-63
Hz, output 24 V/5 A
Weight (including power supply): 2.1 kg
Virtual instruments (meters and sources):
2 x Voltmeter VIs, 2 x Ammeter VIs: AC, DC, 9 ranges, 100mV
to 50V, true RMS, AV
1 x VI with 8 relays, 1 x Multimeter VI: multimeter display
(optional LM2330, LM2331 or LM2322) in LabSoft
1 x 2-channel ammeter VI: AC, DC, 2 ranges, 300 mA and 3 A,
TrueRMS, AV
1 x 2-channel voltmeter VI: AC, DC, 9 ranges, 100 mV to 50 V,
TrueRMS, AV
1 2-/4-channel oscilloscope: band width 10 MHz, 25 time
ranges, 100 ns/div to 10 s/div, 9 ranges 20 mV/div to 10 V/div,
trigger and pre-trigger, XY and XT modes, cursor function,
addition and multiplication function for 2 channels
1 x Adjustable DC voltage VI 0 - 10 V
1 x Function generator VI: 0.5 Hz - 5 MHz, 0 - 10 V, sine,
square, triangular,
1 x Arbitrary generator VI, 1 x Pulse generator VI
1 x VI with 16 digital outputs, 1 x VI with 16 x digital inputs, 1 x
Lucas Nülle GmbH
Page 7/113
www.lucas-nuelle.com
VI with 16 digital input/outputs. Display modes: binary, hex,
decimal and octal numerals
1 x Three-phase power supply VI, 0 - 150 Hz, 0 - 14 Vrms, 2 A
(requires CO4203-2B)
1 x Adjustable DC power supply VI, 3 x (-20 V - +20 V), 2 A
(requires CO4203-2B)
1 x Three-phase power supply VI with additional phase-shift
and clock rate adjustment (requires CO4203-2B)
Includes:
Interface
Power supply
Power lead
USB cable
CD with basic software
Operating manual
System requirements:
Personal computer with Windows Vista, Windows 7,
Windows 8, Windows 8.1, Windows 10 (32 or 64 bit version)
CD-ROM drive for installing software
USB port for connection to Interface
6 UniTrain Experimenter
CO4203-2B
3
UniTrain Experimenter for coupling to the UniTrain Interface or to
other Experimenter modules.
Equipment:
Connects to the UniTrain Interface and additional
Experimenters via UniTrain bus
UniTrain bus connection for experiment cards
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front window
Suitable for accommodating training panel frames for DIN A4
training panels
Fixed and variable voltages available via 8 2-mm sockets
Designed for connection of 2-mm safety measuring leads
Accommodates UniTrain experiment cards
Eject mechanism for UniTrain experiment cards with return
spring
Accommodates a breadboard for experimenting with discrete
components and integrated circuits
Accommodates a multimeter using IrDa interface
Dimensions: 29.6 x 19 x 8.6 cm
Weight: 1.0 kg
Lucas Nülle GmbH
Page 8/113
www.lucas-nuelle.com
7 UniTrain-I measurement accessories, shunts and connection
cables
SO4203-2J
1
Shunt resistors on a PCB, for current measurement using the
analog inputs of the UniTrain system.
6 Shunt resistors: 2 x 1 ohm, 2 x 10 ohm, 2 x 100 ohm
Screen print of symbols for identifying resistors, the
voltage taps and current inputs
24 x 2-mm sockets
Dimensions: 100 x 40 mm
Set of connection cables 2mm (22 pcs) for UniTrain consisting
of:
8 x connection leads 2mm, 15cm, blue
4 x connection leads 2mm, 15cm, yellow
2 x connection leads 2mm, 45cm, black
2 x connection leads 2mm, 45cm, yellow
2 x connection leads 2mm, 45cm, red
2 x connection leads 2mm, 45cm, blue
2 x adapter leads 4mm to 2mm, 50cm, white
10 x 2-mm connector plugs / Plug spacing 5mm
Additionally recommended
Pos.
Product name
Bestell-Nr.
8 UniTrain storage case for one system
CO4203-2Y
Anz.
1
Sturdy aluminium case with moulded foam block to
accommodate a complete UniTrain system (without equipment)
Capable of accommodating 1 Interface, 2 Experimenters,
1 power supply as well as cables and smaller accessories
Lockable padlock; stable padlock hinge
Colours: aluminium, black, chrome
Dimensions: 610 x 480 x 100 mm
Weight: 4,6 kg
Lucas Nülle GmbH
Page 9/113
www.lucas-nuelle.com
Transmission lines
Transmission lines
Lucas Nülle GmbH
Page 10/113
www.lucas-nuelle.com
List of articles:
Supplementary Set for SO4204-9U:
Pos.
Product name
Bestell-Nr.
9 Course Telecommunications 2: Coaxial cables
SO4204-9G
Anz.
1
Includes:
Experiment card "RLC-measuring bridge"
Experiment card "Pulse generator"
Experiment module with 20 m / 40 m / 60 m coaxial
cables
Different terminators
Coaxial cable accessories
CD-ROM with browser and course software
Course contents:
Introduction to the concepts resistance, capacitance and
inductance per unit length and characteristic impedance
of a coaxial cable
Determining the resistance per unit length of a coaxial
cable using a Wheatstone bridge
Determining the capacitance per unit length of a coaxial
cable using a Wien bridge
Determining the inductance per unit length of a coaxial
cable using a Maxwell bridge
Determining the surge impedance of a coaxial cable
Investigation of reflections in a coaxial cable depending on
termination
Predicting the response of a cable when incorrectly
terminated
Proper termination of a cable to eliminate reflection
Course duration 4 h approx.
Lucas Nülle GmbH
Page 11/113
www.lucas-nuelle.com
10 Course Telecommunications 3: Fibre optics
SO4204-9E
1
Includes:
1 Experiment card with optical fibres – transmitter card with
two transmitting diodes of differing wavelengths
1 Experiment card with optical fibre receiver
Fibre-optic kit, (20 fibre-optic plugs, 2 different fibre-optic
cables)
Optical gauge and stripper
CD-ROM with Labsoft browser and course software
Course contents:
Introduction to the principles of optical data transmission:
converting electrical signals into optical signals and optical
signals into electrical signals
Identifying the key components for optical data transmission
List of advantages and disadvantages for optical data lines
Recording the characteristic and frequency response of infrared transmitter diodes
Control of a transmitter diode
Investigation of various modulation methods for analog and
TTL signals by measurement
Investigation of a data carrying optical fibre for different
wavelengths of infra-red light
Configuration of a fibre-optic cable
Investigating the effect of the receiver diode on signal recovery
Determining the bandwidth of a fibre-optic transmission line
Investigating the input capacitance of an optical fibre on
bandwidth
Investigation of attenuation in a fibre-optic transmission line
by measurement
Investigating the effect axial and lateral misalignment at
splices by measurement
Comparing the properties of step index and graded index
fibres
Investigating the effect of wavelength on attenuation
Course duration 4 h approx.
Lucas Nülle GmbH
Page 12/113
www.lucas-nuelle.com
11 Course Telecommunications 4: Four-wire lines
SO4204-9F
1
Includes:
1 Experiment card "Measuring bridge"
1 Experiment card "Impuls generator"
1 Cable reel
CD-ROM with Labsoft browser and course software
Course contents:
Measuring line parameters at various frequencies with the
help of a bridge
Measuring side-circuit resistance at various
frequencies
Measuring ohmic conductance at various frequencies
Measuring side-circuit inductance at various
frequencies
Measuring side-circuit capacitance at various
frequencies
Measuring characteristic impedance over the audio IDSN - ADSL frequency range
Understanding a measuring bridge's functions,
including balancing
Measuring characteristic impedance and the propagation
constant
Measuring pulse transit time on conductor pairs and
individual wires with respect to ground
Using a function generator and oscilloscope to
measure pulse transit time on conductor pairs
Using a function generator and oscilloscope to
measure pulse transit time on individual wires with
respect to the shielding
Measuring cross-talk between a four-wire line's conductor
pairs
Lucas Nülle GmbH
Page 13/113
www.lucas-nuelle.com
12 Course Microwave technology 3: Microstrip technology
SO4204-9Y
1
Includes:
1 Network analyser experiment card, frequency range 1 - 2
GHz, sensitivity -60 - 0 dBm, power output 6 - 10 dBm,
frequency resolution 10 MHz
Microstrip components: 3 microstrips, Wilkinson divider, 2
low-pass filters (3rd and 5th order), band-pass filter, bandstop filter (butterfly antenna), FET and MMIC amplifiers, 2
branching modules
Measuring accessories: SMA lead, attenuator and 2
terminators
CD-ROM with Labsoft browser and course software
Course contents:
Planar microstrips
Calculation of line characteristics
Investigation of transfer function
Simple microwave circuits
Descriptions involving scattering parameters
Scattering matrix
Investigation of transfer function for a Wilkinson divider and a
directed coupler
Microstrip filters
Filter design
3rd and 5th order low-pass filters
Band-pass (edge coupled) filters
Band-stop filter (butterfly antenna)
Microwave amplifiers
MMIC amplifiers
Low-noise FET amplifiers
Investigation of relections
Determination of standing wave ratios
Course duration: 8 h approx.
Lucas Nülle GmbH
Page 14/113
www.lucas-nuelle.com
13 Course Microwave technology 1: Introduction to microwave
technology
SO4204-9U
1
Includes:
1 experiment card X-Band-measurement interface:
operational frequency 8,0-9,9GHz, logarithmic detection,
dynamic range up to 50dB, resolution 16bit
High quality waveguides:
- Gunn oscillator with high precision frequency tuning micrometer
screw
- isolator
- variable attenuator
- slotted line
- line displacement record
- 3-screw transformer
- waveguide terminator
- waveguide adapter
- waveguide short
- horn aerial 10dB
Standbases and connecting cables
Aluminum storage case
CD-ROM with Labsoft-Browser and course software
Microwave source
Gunn oscillator
Frequency 8,0..9,9GHz, ultra stable and maintenance-free
Safety first - low-power emission and measurement only
emission
Overvoltage protection
Receiver
X-Band-LNC, frequency range 8...10GHz
High accuracy measurements with sensitivity up to 75dBm
Real-time frequency measurement of 8...10GHz signals
Internal gain approx. 16dB
Course contents:
Lucas Nülle GmbH
Page 15/113
www.lucas-nuelle.com
Characteristics of electromagnetic waves
Gunn oscillator
LNC receiver
Recording of current-voltage characteristics
Transmission line theory and line quantities of unit length
Wave propagation in waveguides
Standing waves, shorted waveguide, reflection and
matching
SWR
Power loss and thermal load
Measurement of wave distribution along the waveguide
with the slotted measurement line
Propagation of TE and TM waves
Waveguide dimensions and operating frequency
Dielectrics in waveguides
Course duration 4.5 h approx.
Lucas Nülle GmbH
Page 16/113
www.lucas-nuelle.com
14 Course Microwave Technology 2: Waveguide components
SO4204-9V
1
Includes:
High-quality R100 waveguide with Easyfix quick fastening
system and centering pins for rapid and precise
assembly:
- E- and H-plane bends
- Waveguide coax transition
- Rotary coupling
- Phase-shifter
- PIN modulator
- Directional coupler
- Cross coupler
- Ferrite circulator
- Slotted impedance adapter
- Short-circuit shifter with micrometer screw
2 standbases with adjustable height and connection cable
Aluminium case for storage purposes
CD-ROM with Labsoft browser and course software
Course contents:
List of basic equations describing wave propagation in a
waveguide
Equations used for the characterisation of a waveguide
Waveguide elements for changing directions: rotary
coupling, E-plane and H-plane bends
Determine the characteristic of a variable attenuator
Design and operation of a waveguide phase-shifter
Measurement of the phase-shift in a waveguide
Measurement of attenuation and isolation of a ferrite
isolator
Design and operation of direction-dependent waveguide
components
Measurements of attenuation and reflection of cross
couplers, directional couplers and Ferrite circulators
Measurement of insertion and coupling attenuation
Modulation and demodulation of microwaves in the
waveguide
Investigation of a PIN modulator using measuring
Lucas Nülle GmbH
Page 17/113
www.lucas-nuelle.com
instruments
Line characterisation using the Smith chart
Use of Smith chart in determining impedance and
reflection factor
Line matching with the aid of a slotted impedance adapter
Investigation of the microwave signal at open end of line
Course duration: approx. 8h
Lucas Nülle GmbH
Page 18/113
www.lucas-nuelle.com
Additionally required:
The UniTrain-I system is a computer-based training and experimentation system for vocational and further
training and education in the areas of basic and advanced electrical engineering and electronics. Its multimedia
courses combine cognitive and hands-on (haptic) training units into a comprehensive unified concept,
specifically enabling students to acquire skills in the handling of equipment. Starting with basic courses and
advancing to cover a huge variety of electrical engineering and electronics topics, a wide range of multimedia
courses is available for study in school or in professional and advanced training courses. The UniTrain-I system
is completely self-contained and can be used anywhere at any time. The multimedia learning environment the
system provides high degrees of motivation, and maximum learning effectiveness in laboratories, at work or at
home. It thus becomes a guarantor for effective and efficient study. Access to the multimedia courses and
control of virtual instruments and experiment hardware is provided by LabSoft, the system's open experiment
platform. The courses teach the theoretical building blocks and provide experiments to be carried out using the
course-specific experiment hardware. The intelligent measurement interface supplies the analog and digital
measuring and control I/O and represents, in combination with the system's virtual instruments, a high quality
item of laboratory equipment. In addition, students' progress can be monitored and electronically documented on
the basis of fault finding experiments with faults simulated by the hardware as well as tests of knowledge. The
electrical and electronic circuits needed for the experiments are connected to the system with the aid of an
Experimenter module.
Lucas Nülle GmbH
Page 19/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
15 UniTrain Interface with virtual instruments (basic VI)
CO4203-2A
Anz.
1
The UniTrain Interface is the central unit of the UniTrain system. It
incorporates all inputs and outputs, switches, power and signal
sources and measurement circuitry needed to perform experiments.
The Interface is controlled via the connected PC.
Equipment:
32-bit processor with storage memory for measurements
USB interfaces, transfer rate 12 Mbits/s
WLAN/WiFi interface, 2.4 GHz, IEEE 802.11 b/g/n
Simultaneous connection of any number of Experimenters via
serial bus system
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front panel
Suitable for accommodating in training panel frames for DIN
A4 training panels
Designed for connection of 2-mm safety measuring leads
Multi-coloured LEDs for displaying status
Adjustable analog output, +/-10 V, 0.2 A, DC – 5 MHz, via BNC
and 2-mm sockets
4 Analog differential amplifier inputs with 10 MHz band width,
safe for voltages up to 100 V, sampling rate 100 mega
samples, 9 measuring ranges, memory depth 4 x 8 k x 10
bits, inputs via BNC (2 inputs) or 2-mm sockets (4 inputs)
2 Analog inputs for current measurement, overcurrentprotected up to 5 A, sampling rate 250 kilo samples, 2
measuring ranges, resolution 12 bits, connection via 2-mm
sockets
16-bit digital signal output, of which 8 bits are accessed via 2mm sockets, TTL/CMOS, clock frequency 0 – 100 kHz, electric
strength +/- 15 V
16-bit digital signal input, of which 8 bits are accessed via 2mm sockets, memory depth 16 bit x 2 k, TTL/CMOS, sampling
rate 0 – 100 kHz, electric strength +/- 15 V,
8 Relays, 24 V DC/1 A, of which 4 are accessed via 2-mm
sockets
Dimensions: 29.6 x 19 x 8.6 cm
External power supply with wide range input 100-264 V, 47-63
Hz, output 24 V/5 A
Weight (including power supply): 2.1 kg
Virtual instruments (meters and sources):
2 x Voltmeter VIs, 2 x Ammeter VIs: AC, DC, 9 ranges, 100mV
to 50V, true RMS, AV
1 x VI with 8 relays, 1 x Multimeter VI: multimeter display
(optional LM2330, LM2331 or LM2322) in LabSoft
1 x 2-channel ammeter VI: AC, DC, 2 ranges, 300 mA and 3 A,
TrueRMS, AV
1 x 2-channel voltmeter VI: AC, DC, 9 ranges, 100 mV to 50 V,
TrueRMS, AV
1 2-/4-channel oscilloscope: band width 10 MHz, 25 time
ranges, 100 ns/div to 10 s/div, 9 ranges 20 mV/div to 10 V/div,
trigger and pre-trigger, XY and XT modes, cursor function,
addition and multiplication function for 2 channels
1 x Adjustable DC voltage VI 0 - 10 V
1 x Function generator VI: 0.5 Hz - 5 MHz, 0 - 10 V, sine,
square, triangular,
1 x Arbitrary generator VI, 1 x Pulse generator VI
1 x VI with 16 digital outputs, 1 x VI with 16 x digital inputs, 1 x
Lucas Nülle GmbH
Page 20/113
www.lucas-nuelle.com
VI with 16 digital input/outputs. Display modes: binary, hex,
decimal and octal numerals
1 x Three-phase power supply VI, 0 - 150 Hz, 0 - 14 Vrms, 2 A
(requires CO4203-2B)
1 x Adjustable DC power supply VI, 3 x (-20 V - +20 V), 2 A
(requires CO4203-2B)
1 x Three-phase power supply VI with additional phase-shift
and clock rate adjustment (requires CO4203-2B)
Includes:
Interface
Power supply
Power lead
USB cable
CD with basic software
Operating manual
System requirements:
Personal computer with Windows Vista, Windows 7,
Windows 8, Windows 8.1, Windows 10 (32 or 64 bit version)
CD-ROM drive for installing software
USB port for connection to Interface
16 UniTrain Experimenter
CO4203-2B
2
UniTrain Experimenter for coupling to the UniTrain Interface or to
other Experimenter modules.
Equipment:
Connects to the UniTrain Interface and additional
Experimenters via UniTrain bus
UniTrain bus connection for experiment cards
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front window
Suitable for accommodating training panel frames for DIN A4
training panels
Fixed and variable voltages available via 8 2-mm sockets
Designed for connection of 2-mm safety measuring leads
Accommodates UniTrain experiment cards
Eject mechanism for UniTrain experiment cards with return
spring
Accommodates a breadboard for experimenting with discrete
components and integrated circuits
Accommodates a multimeter using IrDa interface
Dimensions: 29.6 x 19 x 8.6 cm
Weight: 1.0 kg
Lucas Nülle GmbH
Page 21/113
www.lucas-nuelle.com
17 UniTrain-I measurement accessories, shunts and connection
cables
SO4203-2J
1
Shunt resistors on a PCB, for current measurement using the
analog inputs of the UniTrain system.
6 Shunt resistors: 2 x 1 ohm, 2 x 10 ohm, 2 x 100 ohm
Screen print of symbols for identifying resistors, the
voltage taps and current inputs
24 x 2-mm sockets
Dimensions: 100 x 40 mm
Set of connection cables 2mm (22 pcs) for UniTrain consisting
of:
8 x connection leads 2mm, 15cm, blue
4 x connection leads 2mm, 15cm, yellow
2 x connection leads 2mm, 45cm, black
2 x connection leads 2mm, 45cm, yellow
2 x connection leads 2mm, 45cm, red
2 x connection leads 2mm, 45cm, blue
2 x adapter leads 4mm to 2mm, 50cm, white
10 x 2-mm connector plugs / Plug spacing 5mm
Lucas Nülle GmbH
Page 22/113
www.lucas-nuelle.com
Additionally recommended
Pos.
Product name
Bestell-Nr.
18 Multi 18 digital multimeter
LM2331
Anz.
1
Universal precision lab multimeter and temperature meter with IR
interface for high-quality, universal measurement and testing in
educational settings, power plants, process control installations etc.
4¾-digit multimeter; resolution: ±31,000 digits
Measurement classification CATII-1000V
Can be connected to UniTrain-I system via IR interface
Real-time RMS measurement TRMS
Voltage and current measuring ranges (AC and DC): 300mV1000V; 300µA-10A
Decibel measurement
Resistance ranges: 300ohm-30Mohm
Capacitance measuring range 3nF to 10,000µF
Frequency measuring range up to 100 kHz, counter and
stopwatch
Special functions: ° C for temperature measurements using
PT100/1000 thermocouple
Continuity and diode testing
Automatic range selection and battery shut-off, min./max. and
data hold function
Protection against high currents in the mA range for nominal
voltage of 1000V
Safety fuse for all current measurement ranges (up to
10A)
Display with bar chart and backlighting
Includes protective sleeve, measuring leads, 2 x spare fuses,
9V battery, calibration certificate
Lucas Nülle GmbH
Page 23/113
www.lucas-nuelle.com
19 UniTrain storage case for one system
CO4203-2Y
1
Sturdy aluminium case with moulded foam block to
accommodate a complete UniTrain system (without equipment)
Capable of accommodating 1 Interface, 2 Experimenters,
1 power supply as well as cables and smaller accessories
Lockable padlock; stable padlock hinge
Colours: aluminium, black, chrome
Dimensions: 610 x 480 x 100 mm
Weight: 4,6 kg
Modulation and multiplexing
Modulation and multiplexing
Lucas Nülle GmbH
Page 24/113
www.lucas-nuelle.com
List of articles:
Lucas Nülle GmbH
Page 25/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
20 Course Telecommunications 5: Pulse modulation methods PAM,
PCM, Delta
SO4204-9J
Anz.
1
Includes:
1 Experiment card with PAM PCM modulator
1 Experiment card with PAM PCM demodulator
1 Experiment card with AMI/HDB3 coder/decoder
CD-ROM with Labsoft browser and course software
Course contents:
Introduction to PAM/PCM/Delta modulation, PAM/PCM/Delta
demodulation, time multiplexing
Shannon's sampling theorem
Measuring PAM modulated signals over time
Optimal filtering and anti-aliasing
Identifying advantages and disadvantages of digital
transmission
Introduction to the principle quantisation of analog signals
Generation of parallel and serial codes
Companding methods using A law and µ law
Determining quantising interval for a PCM transmission by
measurement
Measuring PCM coded signals over time
Recording logarithmic transfer characteristics with
companding according to a law and µ law (13 or 15
segments)
Measuring PCM time-multiplexed signals over time
Introduction to the key features of transmission codes
Introduction to pseudo-ternary codes AMI, HDB3, modified AMI
Measuring line-coded signals over time: AMI, HDB3 and
modified AMI
Transmission of information on a line along with clocking and
synchronisation information
Clock recovery and phase jitter
Introduction to data packet formats for ISDN layer 1
(Integrated Services Digital Network)
ISDN layer 1, investigation of position and function of frames
and bits
Investigation of a 2 channel transmission with control
channel at data rates of 64kbits per channel
Lucas Nülle GmbH
Page 26/113
www.lucas-nuelle.com
Course duration 4 h approx.
21 Course Telecommunications 6: Pulse modulation methods PWM,
PPM
SO4204-9K
1
Includes:
1 Experiment card with PWM modulator and demodulator;
tunable demodulator filter frequency
1 Experiment card with PPM modulator and demodulator;
access to internal signals in the demodulator via 2mm
sockets
CD-ROM with Labsoft browser and course software
Course contents:
Introduction to the principles of pulse-width modulation
(PWM) and pulse-width demodulation
Recording the signal characteristic at the output of a pulse
width modulator
Investigation of the output signal from a PWM demodulator
Investigation of the demodulated signal with relation to the
bandwidth of the input signal
Listing the advantages and disadvantages of PWM
Introduction to the principle of pulse-position modulation
(PPM) and demodulation
Recording the change in signal at the output of a pulseposition modulator
Measurement of signal internal to a demodulator over time
Listing the advantages and disadvantages of PPM
Course duration 2 h approx.
Lucas Nülle GmbH
Page 27/113
www.lucas-nuelle.com
22 Course Telecommunications 7: Modem methods ASK, FSK, PSK
SO4204-9L
1
Includes:
1 Experiment card with PSK/QPSK modulator
1 Experiment card with PSK/QPSK demodulator
1 Experiment card with ASK modulator/demodulator
1 Experiment card with FSK modulator/demodulator
CD-ROM with Labsoft browser and course software
Course contents:
Introduction to the principle of ASK modulation and
demodulation for transmitting digital signals over analog
lines
Investigation of the spectrum of an ASK-modulated signal by
measurement
Investigating the relationship between data transfer rate and
the required bandwidth
Introduction to the principles of FSK modulation and
demodulation for transmitting digital signals over analog
lines
Identifying advantages of FSK modulation over ASK
modulation
Investigation of the spectrum of an FSK-modulated signal by
measurement
Investigation of the relationship between data transfer rate
and the required bandwidth
Introduction to the operation of a PLL
Demodulation of FSK signals using a PLL circuit
Introduction to the principles of PSK (DPSK) modulation and
demodulation
Generation of 2 PSK signals at different baud rates
Introduction to the principles of QPSK and DQPSK
modulation und demodulation
Generation of 4 PSK signals
Introduction to generation of dibits
Relationship between data rate and baud rate by
measurement
Measurement of signals at the output of modulators and
demodulator (ASK, FSK, (Q)PSK) over time
List of advantages and disadvantages for various modulation
methods
Course duration 2.5 h approx.
Lucas Nülle GmbH
Page 28/113
www.lucas-nuelle.com
23 Course Telecommunications 8: AM/FM modulation/demodulation
SO4204-9M
1
Includes:
1 Experiment card with Colpitts/Hartley oscillator
1 Experiment card with AM modulator/demodulator, AM
modulator switchable between AM/DSB, product demodulator
and diode detector
1 Experiment card with FM modulator/phase demodulator
CD-ROM with Labsoft browser and course software
Course contents:
Introduction to the principle of amplitude modulation by
measuring AM modulator signals over time
Recording the modulation trapezoid for various modulation
depths
Demodulation of an amplitude modulated signal
Introduction to the principle of a diode detector
Demonstration of double side-band modulation (DSB)
Tuning the modulator to minimise residual carrier
Recording signal, phase shift and modulation trapezoid for
DSB
Demonstration of single side-band modulation (SSB)
Recovery of the original signal from an SSB signal with the
help of an integrated double balanced mixer
Demonstration of the principle of frequency modulation and
demodulation
Explanation of the term "instantaneous frequency" for a
modulated signal
Determination of the maximum frequency deviation in an FM
signal
Effect of low-frequency amplitude and frequencies on an FM
signal
Explanation of the modulation index
Explanation of the relationship between LF amplitude, LF
frequency and phase shift
Ratio detector and phase detector (Foster-Seeley)
Recovery of a modulated signal by a phase demodulator
Course duration 3 h approx.
Lucas Nülle GmbH
Page 29/113
www.lucas-nuelle.com
Additionally required:
The UniTrain-I system is a computer-based training and experimentation system for vocational and further
training and education in the areas of basic and advanced electrical engineering and electronics. Its multimedia
courses combine cognitive and hands-on (haptic) training units into a comprehensive unified concept,
specifically enabling students to acquire skills in the handling of equipment. Starting with basic courses and
advancing to cover a huge variety of electrical engineering and electronics topics, a wide range of multimedia
courses is available for study in school or in professional and advanced training courses. The UniTrain-I system
is completely self-contained and can be used anywhere at any time. The multimedia learning environment the
system provides high degrees of motivation, and maximum learning effectiveness in laboratories, at work or at
home. It thus becomes a guarantor for effective and efficient study. Access to the multimedia courses and
control of virtual instruments and experiment hardware is provided by LabSoft, the system's open experiment
platform. The courses teach the theoretical building blocks and provide experiments to be carried out using the
course-specific experiment hardware. The intelligent measurement interface supplies the analog and digital
measuring and control I/O and represents, in combination with the system's virtual instruments, a high quality
item of laboratory equipment. In addition, students' progress can be monitored and electronically documented on
the basis of fault finding experiments with faults simulated by the hardware as well as tests of knowledge. The
electrical and electronic circuits needed for the experiments are connected to the system with the aid of an
Experimenter module.
Lucas Nülle GmbH
Page 30/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
24 UniTrain Interface with virtual instruments (basic VI)
CO4203-2A
Anz.
1
The UniTrain Interface is the central unit of the UniTrain system. It
incorporates all inputs and outputs, switches, power and signal
sources and measurement circuitry needed to perform experiments.
The Interface is controlled via the connected PC.
Equipment:
32-bit processor with storage memory for measurements
USB interfaces, transfer rate 12 Mbits/s
WLAN/WiFi interface, 2.4 GHz, IEEE 802.11 b/g/n
Simultaneous connection of any number of Experimenters via
serial bus system
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front panel
Suitable for accommodating in training panel frames for DIN
A4 training panels
Designed for connection of 2-mm safety measuring leads
Multi-coloured LEDs for displaying status
Adjustable analog output, +/-10 V, 0.2 A, DC – 5 MHz, via BNC
and 2-mm sockets
4 Analog differential amplifier inputs with 10 MHz band width,
safe for voltages up to 100 V, sampling rate 100 mega
samples, 9 measuring ranges, memory depth 4 x 8 k x 10
bits, inputs via BNC (2 inputs) or 2-mm sockets (4 inputs)
2 Analog inputs for current measurement, overcurrentprotected up to 5 A, sampling rate 250 kilo samples, 2
measuring ranges, resolution 12 bits, connection via 2-mm
sockets
16-bit digital signal output, of which 8 bits are accessed via 2mm sockets, TTL/CMOS, clock frequency 0 – 100 kHz, electric
strength +/- 15 V
16-bit digital signal input, of which 8 bits are accessed via 2mm sockets, memory depth 16 bit x 2 k, TTL/CMOS, sampling
rate 0 – 100 kHz, electric strength +/- 15 V,
8 Relays, 24 V DC/1 A, of which 4 are accessed via 2-mm
sockets
Dimensions: 29.6 x 19 x 8.6 cm
External power supply with wide range input 100-264 V, 47-63
Hz, output 24 V/5 A
Weight (including power supply): 2.1 kg
Virtual instruments (meters and sources):
2 x Voltmeter VIs, 2 x Ammeter VIs: AC, DC, 9 ranges, 100mV
to 50V, true RMS, AV
1 x VI with 8 relays, 1 x Multimeter VI: multimeter display
(optional LM2330, LM2331 or LM2322) in LabSoft
1 x 2-channel ammeter VI: AC, DC, 2 ranges, 300 mA and 3 A,
TrueRMS, AV
1 x 2-channel voltmeter VI: AC, DC, 9 ranges, 100 mV to 50 V,
TrueRMS, AV
1 2-/4-channel oscilloscope: band width 10 MHz, 25 time
ranges, 100 ns/div to 10 s/div, 9 ranges 20 mV/div to 10 V/div,
trigger and pre-trigger, XY and XT modes, cursor function,
addition and multiplication function for 2 channels
1 x Adjustable DC voltage VI 0 - 10 V
1 x Function generator VI: 0.5 Hz - 5 MHz, 0 - 10 V, sine,
square, triangular,
1 x Arbitrary generator VI, 1 x Pulse generator VI
1 x VI with 16 digital outputs, 1 x VI with 16 x digital inputs, 1 x
Lucas Nülle GmbH
Page 31/113
www.lucas-nuelle.com
VI with 16 digital input/outputs. Display modes: binary, hex,
decimal and octal numerals
1 x Three-phase power supply VI, 0 - 150 Hz, 0 - 14 Vrms, 2 A
(requires CO4203-2B)
1 x Adjustable DC power supply VI, 3 x (-20 V - +20 V), 2 A
(requires CO4203-2B)
1 x Three-phase power supply VI with additional phase-shift
and clock rate adjustment (requires CO4203-2B)
Includes:
Interface
Power supply
Power lead
USB cable
CD with basic software
Operating manual
System requirements:
Personal computer with Windows Vista, Windows 7,
Windows 8, Windows 8.1, Windows 10 (32 or 64 bit version)
CD-ROM drive for installing software
USB port for connection to Interface
25 UniTrain Experimenter
CO4203-2B
3
UniTrain Experimenter for coupling to the UniTrain Interface or to
other Experimenter modules.
Equipment:
Connects to the UniTrain Interface and additional
Experimenters via UniTrain bus
UniTrain bus connection for experiment cards
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front window
Suitable for accommodating training panel frames for DIN A4
training panels
Fixed and variable voltages available via 8 2-mm sockets
Designed for connection of 2-mm safety measuring leads
Accommodates UniTrain experiment cards
Eject mechanism for UniTrain experiment cards with return
spring
Accommodates a breadboard for experimenting with discrete
components and integrated circuits
Accommodates a multimeter using IrDa interface
Dimensions: 29.6 x 19 x 8.6 cm
Weight: 1.0 kg
Lucas Nülle GmbH
Page 32/113
www.lucas-nuelle.com
26 UniTrain-I measurement accessories, shunts and connection
cables
SO4203-2J
1
Shunt resistors on a PCB, for current measurement using the
analog inputs of the UniTrain system.
6 Shunt resistors: 2 x 1 ohm, 2 x 10 ohm, 2 x 100 ohm
Screen print of symbols for identifying resistors, the
voltage taps and current inputs
24 x 2-mm sockets
Dimensions: 100 x 40 mm
Set of connection cables 2mm (22 pcs) for UniTrain consisting
of:
8 x connection leads 2mm, 15cm, blue
4 x connection leads 2mm, 15cm, yellow
2 x connection leads 2mm, 45cm, black
2 x connection leads 2mm, 45cm, yellow
2 x connection leads 2mm, 45cm, red
2 x connection leads 2mm, 45cm, blue
2 x adapter leads 4mm to 2mm, 50cm, white
10 x 2-mm connector plugs / Plug spacing 5mm
Additionally recommended
Pos.
Product name
Bestell-Nr.
27 UniTrain storage case for one system
CO4203-2Y
Anz.
1
Sturdy aluminium case with moulded foam block to
accommodate a complete UniTrain system (without equipment)
Capable of accommodating 1 Interface, 2 Experimenters,
1 power supply as well as cables and smaller accessories
Lockable padlock; stable padlock hinge
Colours: aluminium, black, chrome
Dimensions: 610 x 480 x 100 mm
Weight: 4,6 kg
Lucas Nülle GmbH
Page 33/113
www.lucas-nuelle.com
Transmitting and receiving technology
Transmitting and receiving technology
Lucas Nülle GmbH
Page 34/113
www.lucas-nuelle.com
List of articles:
Supplementary Set for SO4204-9T:
Lucas Nülle GmbH
Page 35/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
28 Course Telecommunications 9: AM transmission and receiving
technology
SO4204-9N
Anz.
1
Includes:
1 Experiment card with AM modulator/demodulator, AM
modulator switchable between AM/DSB, product demodulator
and diode detector
1 Experiment card with AM receiver and HF input stage
1 Experiment card with AM IF (intermediate frequency-), LF
(low-frequency) amplifier
1 Experiment card with Colpitts-/Hartley-Oscillator
CD-ROM with Labsoft browser and course software
Course contents:
Introduction to the design and function of Hartley- and Colpitts
oscillators
Tuning oscillators
Introduction to principles of capacitive and inductive feedback
Investigation of resonance conditions (self-excitation) by
measurement
Design and investigation of an AM transmitter
Tuning an oscillator and measuring various degrees of
modulation
Measuring the frequency response of the output voltage of an
oscillator
Design and investigation of an AM receiver
Introduction to the principle of receiver design
Tuned radio frequency receivers
Superhet receivers
Automatic gain control AGC
Automatic frequency control AFC
Investigation of a phase discriminator (Foster-Seeley) by
measurement
Introduction to the terms signal-to-image ratio (far-off
selectivity) with and without pre-selector stage
Demonstration and determination of the image frequency in
superhet receivers by measurement
Investigation of filter curves of high-frequency input stages IF
amplifiers by measurement
Determination of adjacent-channel selectivity
Design of a medium-wave AM single stage superhet receiver
Lucas Nülle GmbH
Page 36/113
www.lucas-nuelle.com
with full-range tuning
Course duration 4.5 h approx.
29 Course Telecommunications 10: Data acquisition using RFID
SO4204-9S
1
Includes:
1 RFID-Reader experiment card, frequency range 13.56 MHz
1 RFID-Antenna experiment card
Measurement transponder
Transponder: 2x chip card, 2x label, 2x plastic housing
2 BNC cables
CD-ROM with Labsoft browser and course software
Course contents:
Overview of RFID technology
Application areas of RFID systems
Familiarisation with RFID system components
Identifying various transponder types
Learning about the operating frequencies of various RFID
systems
Naming the properties and reach of different RFID systems
Learning the procedures for energy link and data
transmission
Transformer principle and electrical resonant circuit
Auxillary carrier modulation
RFID standard ISO15693
Data coding and transmission analysis
Writing onto and reading from the transponder
Assessing RFID messages according to ISO15693 using
measuring techniques
Anti-collision procedure
Standard commands and flags in the RFID protocol
Course duration: approx.. 4 h
Lucas Nülle GmbH
Page 37/113
www.lucas-nuelle.com
30 Course Antenna Technology 1 : Antenna Technology
SO4204-9T
1
Includes:
1 Experiment card with the X-Band Antenna Interface,
logarithmic detector with >60 dB dynamic range, 16 bit
measurement resolution
CD-ROM with Labsoft browser and course software
Antenna rotation platform controlled by stepping motor
with a resolution of 0.1°
Tripod stand with mountings and connection cables
Storage case.
Antennae:
Monopole, dipole and folded-dipole
3-element and 6-element Yagi-array
Helix antennae; right and left polarisation
Patch antennae, linear and circular polarisation.
Transmitter
X-band oscillator with dielectric resonator
Fixed frequency 9.0GHz, stable and maintenance-free
Safety First – low transmission power and energised only
during measurements
Optical display when radiating
Receiver
X-band LNC
Precise measurement with a high degree of sensitivity up
to –65dBm and higher
True frequency measurement
Course contents:
Introduction to antenna technology, forms of antenna and
examples.
Physics of transmitting and receiving
Resistance of an antenna, matching and balancing
(Balun)
Close-field and distant-field transmission
Lucas Nülle GmbH
Page 38/113
www.lucas-nuelle.com
Antenna gain
Form of directional image
Measurement of directional image for various antennae
Course duration 8 h approx.
Lucas Nülle GmbH
Page 39/113
www.lucas-nuelle.com
31 Course Antenna Technology 2: Complex antenna systems
SO4204-9Z
1
Includes:
CD-ROM with Labsoft browser and course software
Stand equipment, holders, adapters and connection leads
Storage case
Antennae:
10dB, 15dB, 20dB horn antennae
Configurable slot antenna with 10 radiators
Microstrip antenna
Dielectric antenna
Configurable parabolic antenna
Lüneberg lens
Reflecting disc
Waveguide accessories
Terminator
E-bend
Waveguide-coaxial connection
E/H positioner
Adapter R100/UBR100
Course contents:
Introduction
Radiator Arrangements
Far-field Conditions
Patch Antennae
What is a Patch Antenna
Feed to a Patch Antenna
Circular Polarisation
The Radiation Pattern
Linear Polarised Patch Antenna
Circular Polarised Patch Antenna
Horn Antennae
The Horn Antenna
The open Wave Guide
10dB Horn Antenna
15dB Horn Antenna
20dB Horn Antenna
Dielectric Antennae
The Dielectric Radiator
Functioning
Dielectric Antenna
Group Antennae
Lucas Nülle GmbH
Page 40/113
www.lucas-nuelle.com
Phased Array Antennae
The Slot Antennae
Groups of Slot Antennae
Function of the Microstrip Antenna
Parabolic Antennae
The Parabolic Antenna
Types of Parabolic Antennae
Patch Antenna as the Primary Radiator
Horn Antenna as the Primary Radiator
Reflections and RADAR
Reflections in a Radio Transmission Path
Effects of Reflections
The Principle of Radar
Radar Cross Section
Reflections from a smooth surface
Increasing the Reflecting Surface
The passive Radio Transponder
Course duration 16 h approx.
Lucas Nülle GmbH
Page 41/113
www.lucas-nuelle.com
Additionally required:
The UniTrain-I system is a computer-based training and experimentation system for vocational and further
training and education in the areas of basic and advanced electrical engineering and electronics. Its multimedia
courses combine cognitive and hands-on (haptic) training units into a comprehensive unified concept,
specifically enabling students to acquire skills in the handling of equipment. Starting with basic courses and
advancing to cover a huge variety of electrical engineering and electronics topics, a wide range of multimedia
courses is available for study in school or in professional and advanced training courses. The UniTrain-I system
is completely self-contained and can be used anywhere at any time. The multimedia learning environment the
system provides high degrees of motivation, and maximum learning effectiveness in laboratories, at work or at
home. It thus becomes a guarantor for effective and efficient study. Access to the multimedia courses and
control of virtual instruments and experiment hardware is provided by LabSoft, the system's open experiment
platform. The courses teach the theoretical building blocks and provide experiments to be carried out using the
course-specific experiment hardware. The intelligent measurement interface supplies the analog and digital
measuring and control I/O and represents, in combination with the system's virtual instruments, a high quality
item of laboratory equipment. In addition, students' progress can be monitored and electronically documented on
the basis of fault finding experiments with faults simulated by the hardware as well as tests of knowledge. The
electrical and electronic circuits needed for the experiments are connected to the system with the aid of an
Experimenter module.
Lucas Nülle GmbH
Page 42/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
32 UniTrain Interface with virtual instruments (basic VI)
CO4203-2A
Anz.
1
The UniTrain Interface is the central unit of the UniTrain system. It
incorporates all inputs and outputs, switches, power and signal
sources and measurement circuitry needed to perform experiments.
The Interface is controlled via the connected PC.
Equipment:
32-bit processor with storage memory for measurements
USB interfaces, transfer rate 12 Mbits/s
WLAN/WiFi interface, 2.4 GHz, IEEE 802.11 b/g/n
Simultaneous connection of any number of Experimenters via
serial bus system
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front panel
Suitable for accommodating in training panel frames for DIN
A4 training panels
Designed for connection of 2-mm safety measuring leads
Multi-coloured LEDs for displaying status
Adjustable analog output, +/-10 V, 0.2 A, DC – 5 MHz, via BNC
and 2-mm sockets
4 Analog differential amplifier inputs with 10 MHz band width,
safe for voltages up to 100 V, sampling rate 100 mega
samples, 9 measuring ranges, memory depth 4 x 8 k x 10
bits, inputs via BNC (2 inputs) or 2-mm sockets (4 inputs)
2 Analog inputs for current measurement, overcurrentprotected up to 5 A, sampling rate 250 kilo samples, 2
measuring ranges, resolution 12 bits, connection via 2-mm
sockets
16-bit digital signal output, of which 8 bits are accessed via 2mm sockets, TTL/CMOS, clock frequency 0 – 100 kHz, electric
strength +/- 15 V
16-bit digital signal input, of which 8 bits are accessed via 2mm sockets, memory depth 16 bit x 2 k, TTL/CMOS, sampling
rate 0 – 100 kHz, electric strength +/- 15 V,
8 Relays, 24 V DC/1 A, of which 4 are accessed via 2-mm
sockets
Dimensions: 29.6 x 19 x 8.6 cm
External power supply with wide range input 100-264 V, 47-63
Hz, output 24 V/5 A
Weight (including power supply): 2.1 kg
Virtual instruments (meters and sources):
2 x Voltmeter VIs, 2 x Ammeter VIs: AC, DC, 9 ranges, 100mV
to 50V, true RMS, AV
1 x VI with 8 relays, 1 x Multimeter VI: multimeter display
(optional LM2330, LM2331 or LM2322) in LabSoft
1 x 2-channel ammeter VI: AC, DC, 2 ranges, 300 mA and 3 A,
TrueRMS, AV
1 x 2-channel voltmeter VI: AC, DC, 9 ranges, 100 mV to 50 V,
TrueRMS, AV
1 2-/4-channel oscilloscope: band width 10 MHz, 25 time
ranges, 100 ns/div to 10 s/div, 9 ranges 20 mV/div to 10 V/div,
trigger and pre-trigger, XY and XT modes, cursor function,
addition and multiplication function for 2 channels
1 x Adjustable DC voltage VI 0 - 10 V
1 x Function generator VI: 0.5 Hz - 5 MHz, 0 - 10 V, sine,
square, triangular,
1 x Arbitrary generator VI, 1 x Pulse generator VI
1 x VI with 16 digital outputs, 1 x VI with 16 x digital inputs, 1 x
Lucas Nülle GmbH
Page 43/113
www.lucas-nuelle.com
VI with 16 digital input/outputs. Display modes: binary, hex,
decimal and octal numerals
1 x Three-phase power supply VI, 0 - 150 Hz, 0 - 14 Vrms, 2 A
(requires CO4203-2B)
1 x Adjustable DC power supply VI, 3 x (-20 V - +20 V), 2 A
(requires CO4203-2B)
1 x Three-phase power supply VI with additional phase-shift
and clock rate adjustment (requires CO4203-2B)
Includes:
Interface
Power supply
Power lead
USB cable
CD with basic software
Operating manual
System requirements:
Personal computer with Windows Vista, Windows 7,
Windows 8, Windows 8.1, Windows 10 (32 or 64 bit version)
CD-ROM drive for installing software
USB port for connection to Interface
33 UniTrain Experimenter
CO4203-2B
3
UniTrain Experimenter for coupling to the UniTrain Interface or to
other Experimenter modules.
Equipment:
Connects to the UniTrain Interface and additional
Experimenters via UniTrain bus
UniTrain bus connection for experiment cards
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front window
Suitable for accommodating training panel frames for DIN A4
training panels
Fixed and variable voltages available via 8 2-mm sockets
Designed for connection of 2-mm safety measuring leads
Accommodates UniTrain experiment cards
Eject mechanism for UniTrain experiment cards with return
spring
Accommodates a breadboard for experimenting with discrete
components and integrated circuits
Accommodates a multimeter using IrDa interface
Dimensions: 29.6 x 19 x 8.6 cm
Weight: 1.0 kg
Lucas Nülle GmbH
Page 44/113
www.lucas-nuelle.com
34 UniTrain-I measurement accessories, shunts and connection
cables
SO4203-2J
1
Shunt resistors on a PCB, for current measurement using the
analog inputs of the UniTrain system.
6 Shunt resistors: 2 x 1 ohm, 2 x 10 ohm, 2 x 100 ohm
Screen print of symbols for identifying resistors, the
voltage taps and current inputs
24 x 2-mm sockets
Dimensions: 100 x 40 mm
Set of connection cables 2mm (22 pcs) for UniTrain consisting
of:
8 x connection leads 2mm, 15cm, blue
4 x connection leads 2mm, 15cm, yellow
2 x connection leads 2mm, 45cm, black
2 x connection leads 2mm, 45cm, yellow
2 x connection leads 2mm, 45cm, red
2 x connection leads 2mm, 45cm, blue
2 x adapter leads 4mm to 2mm, 50cm, white
10 x 2-mm connector plugs / Plug spacing 5mm
Lucas Nülle GmbH
Page 45/113
www.lucas-nuelle.com
Additionally recommended
Pos.
Product name
Bestell-Nr.
35 Multi 18 digital multimeter
LM2331
Anz.
1
Universal precision lab multimeter and temperature meter with IR
interface for high-quality, universal measurement and testing in
educational settings, power plants, process control installations etc.
4¾-digit multimeter; resolution: ±31,000 digits
Measurement classification CATII-1000V
Can be connected to UniTrain-I system via IR interface
Real-time RMS measurement TRMS
Voltage and current measuring ranges (AC and DC): 300mV1000V; 300µA-10A
Decibel measurement
Resistance ranges: 300ohm-30Mohm
Capacitance measuring range 3nF to 10,000µF
Frequency measuring range up to 100 kHz, counter and
stopwatch
Special functions: ° C for temperature measurements using
PT100/1000 thermocouple
Continuity and diode testing
Automatic range selection and battery shut-off, min./max. and
data hold function
Protection against high currents in the mA range for nominal
voltage of 1000V
Safety fuse for all current measurement ranges (up to
10A)
Display with bar chart and backlighting
Includes protective sleeve, measuring leads, 2 x spare fuses,
9V battery, calibration certificate
Lucas Nülle GmbH
Page 46/113
www.lucas-nuelle.com
36 UniTrain storage case for one system
CO4203-2Y
1
Sturdy aluminium case with moulded foam block to
accommodate a complete UniTrain system (without equipment)
Capable of accommodating 1 Interface, 2 Experimenters,
1 power supply as well as cables and smaller accessories
Lockable padlock; stable padlock hinge
Colours: aluminium, black, chrome
Dimensions: 610 x 480 x 100 mm
Weight: 4,6 kg
Digital signal processing
Digital signal processing
Lucas Nülle GmbH
Page 47/113
www.lucas-nuelle.com
List of articles:
Supplementary Set for SO4206-9B:
Pos.
Product name
Bestell-Nr.
37 Course Programming 32-bit ARM Cortex M3 microcontrollers
SO4206-9B
Anz.
1
Includes:
ARM Cortex M3 module
I²C LCD module
2 x Push-buttons
1 x Potentiometer
2 x Resistors, 10k, 0.5W
4 x LEDs
4 x Resistor, 180Ohm, 1W
1 x Resistor, 22k, 0.5W
1 x Resistor, 33k, 0.5W
1 x AND/NAND gate, 2 inputs, 4-fold
1 x USB cable
CD with multimedia course SO4204-9B "Programming 32
bit ARM Cortex M3 microcontrollers"
Training contents:
Introduction to C programming for embedded systems
Cortex M3 architecture and programming model
First steps in programming the Cortex M3 microcontroller
Programming typical microcontroller applications
Lucas Nülle GmbH
Page 48/113
www.lucas-nuelle.com
38 Course Digital Signal Processing using microcontroller 32-Bit Arm
Cortex-M3
SO4206-9C
1
Includes:
I²C audio codec module
PC loudspeaker with power supply and cable
CD with multimedia course SO4206-9B, "Digital signal
processing with a 32-bit ARM Cortex M3 microcontroller"
Training contents:
System components for digital signal processing: Trainees
get an overview of the importance of digital signal
processing. During the course, they learn about the
components of a digital signal processing system, their
classifications and how they work. The individual sections
illustrate the fundamental aspects of the theory behind digital
transfer functions and how they are implemented.
Simple transfer functions: This section develops the
fundamentals of digital signal processing and includes
carrying out the first experiments with simple transfer
functions.
Signal synthesis: The experiment sections are concerned
with the synthesis of various signal shapes with the help
of digital resonators and discrete integrators. The
knowledge learned is put to use in practical experiments.
Signal analysis: Fourier transformation is a fundamental
technique in signal processing. It concerns the conversion
of signals from the time domain to the frequency domain.
Trainees get an idea of how FFT (fast Fourier
transformation) works and how to use it in practical
experiments involving the ARM CORTEX M3 module.
Signal processing: Trainees learn the fundamentals behind
designing digital filters. This involves them implementing in
practice the theoretical basics for calculating the features
of digital filters using design software and thereby creating
their own DSP systems with the 32-bit ARM CORTEX M3
module.
DSP applications: The final section illustrates some
possible applications in the sphere of digital audio signal
processing, which can be tried out by trainees in practical
experiments.
Lucas Nülle GmbH
Page 49/113
www.lucas-nuelle.com
Additionally required:
The UniTrain-I system is a computer-based training and experimentation system for vocational and further
training and education in the areas of basic and advanced electrical engineering and electronics. Its multimedia
courses combine cognitive and hands-on (haptic) training units into a comprehensive unified concept,
specifically enabling students to acquire skills in the handling of equipment. Starting with basic courses and
advancing to cover a huge variety of electrical engineering and electronics topics, a wide range of multimedia
courses is available for study in school or in professional and advanced training courses. The UniTrain-I system
is completely self-contained and can be used anywhere at any time. The multimedia learning environment the
system provides high degrees of motivation, and maximum learning effectiveness in laboratories, at work or at
home. It thus becomes a guarantor for effective and efficient study. Access to the multimedia courses and
control of virtual instruments and experiment hardware is provided by LabSoft, the system's open experiment
platform. The courses teach the theoretical building blocks and provide experiments to be carried out using the
course-specific experiment hardware. The intelligent measurement interface supplies the analog and digital
measuring and control I/O and represents, in combination with the system's virtual instruments, a high quality
item of laboratory equipment. In addition, students' progress can be monitored and electronically documented on
the basis of fault finding experiments with faults simulated by the hardware as well as tests of knowledge. The
electrical and electronic circuits needed for the experiments are connected to the system with the aid of an
Experimenter module.
Lucas Nülle GmbH
Page 50/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
39 UniTrain Interface with virtual instruments (basic VI)
CO4203-2A
Anz.
1
The UniTrain Interface is the central unit of the UniTrain system. It
incorporates all inputs and outputs, switches, power and signal
sources and measurement circuitry needed to perform experiments.
The Interface is controlled via the connected PC.
Equipment:
32-bit processor with storage memory for measurements
USB interfaces, transfer rate 12 Mbits/s
WLAN/WiFi interface, 2.4 GHz, IEEE 802.11 b/g/n
Simultaneous connection of any number of Experimenters via
serial bus system
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front panel
Suitable for accommodating in training panel frames for DIN
A4 training panels
Designed for connection of 2-mm safety measuring leads
Multi-coloured LEDs for displaying status
Adjustable analog output, +/-10 V, 0.2 A, DC – 5 MHz, via BNC
and 2-mm sockets
4 Analog differential amplifier inputs with 10 MHz band width,
safe for voltages up to 100 V, sampling rate 100 mega
samples, 9 measuring ranges, memory depth 4 x 8 k x 10
bits, inputs via BNC (2 inputs) or 2-mm sockets (4 inputs)
2 Analog inputs for current measurement, overcurrentprotected up to 5 A, sampling rate 250 kilo samples, 2
measuring ranges, resolution 12 bits, connection via 2-mm
sockets
16-bit digital signal output, of which 8 bits are accessed via 2mm sockets, TTL/CMOS, clock frequency 0 – 100 kHz, electric
strength +/- 15 V
16-bit digital signal input, of which 8 bits are accessed via 2mm sockets, memory depth 16 bit x 2 k, TTL/CMOS, sampling
rate 0 – 100 kHz, electric strength +/- 15 V,
8 Relays, 24 V DC/1 A, of which 4 are accessed via 2-mm
sockets
Dimensions: 29.6 x 19 x 8.6 cm
External power supply with wide range input 100-264 V, 47-63
Hz, output 24 V/5 A
Weight (including power supply): 2.1 kg
Virtual instruments (meters and sources):
2 x Voltmeter VIs, 2 x Ammeter VIs: AC, DC, 9 ranges, 100mV
to 50V, true RMS, AV
1 x VI with 8 relays, 1 x Multimeter VI: multimeter display
(optional LM2330, LM2331 or LM2322) in LabSoft
1 x 2-channel ammeter VI: AC, DC, 2 ranges, 300 mA and 3 A,
TrueRMS, AV
1 x 2-channel voltmeter VI: AC, DC, 9 ranges, 100 mV to 50 V,
TrueRMS, AV
1 2-/4-channel oscilloscope: band width 10 MHz, 25 time
ranges, 100 ns/div to 10 s/div, 9 ranges 20 mV/div to 10 V/div,
trigger and pre-trigger, XY and XT modes, cursor function,
addition and multiplication function for 2 channels
1 x Adjustable DC voltage VI 0 - 10 V
1 x Function generator VI: 0.5 Hz - 5 MHz, 0 - 10 V, sine,
square, triangular,
1 x Arbitrary generator VI, 1 x Pulse generator VI
1 x VI with 16 digital outputs, 1 x VI with 16 x digital inputs, 1 x
Lucas Nülle GmbH
Page 51/113
www.lucas-nuelle.com
VI with 16 digital input/outputs. Display modes: binary, hex,
decimal and octal numerals
1 x Three-phase power supply VI, 0 - 150 Hz, 0 - 14 Vrms, 2 A
(requires CO4203-2B)
1 x Adjustable DC power supply VI, 3 x (-20 V - +20 V), 2 A
(requires CO4203-2B)
1 x Three-phase power supply VI with additional phase-shift
and clock rate adjustment (requires CO4203-2B)
Includes:
Interface
Power supply
Power lead
USB cable
CD with basic software
Operating manual
System requirements:
Personal computer with Windows Vista, Windows 7,
Windows 8, Windows 8.1, Windows 10 (32 or 64 bit version)
CD-ROM drive for installing software
USB port for connection to Interface
40 EloTrain set of connection cables and plugs for 2mm system
SO5146-1N
1
Measuring lead and plug set, 2mm-system, consisting of:
10 measuring leads, 2mm, 15cm, blue
4 measuring leads, 2mm, 30cm, blue
10 measuring leads, 2mm, 15cm, yellow
4 measuring leads, 2mm, 30cm, yellow
2 measuring leads, 2mm, 45cm, black
4 measuring leads, 2mm, 45cm, red
2 measuring leads, 2mm, 45cm, blue
2 measuring leads, 2mm, 45cm, yellow
1 measuring lead, 4 to 2mm, 50cm, black
1 measuring lead, 4 to 2mm, 50cm, red
60 jumpers 2mm /7.5mm, black
Lucas Nülle GmbH
Page 52/113
www.lucas-nuelle.com
41 EloTrain Experimenter
SO4203-3B
1
EloTrain Experimenter for 2-mm plug-in component system to be
linked to UniTrain-I Interface. 70 nodes allow for easily understood
circuit set-ups in a compact space. Circuits are built by inserting the
plug-in modules between nodes on the board. Connections between
nodes can be made using 2-mm or 7.5-mm jumpers.
Links to a UniTrain-I Interface
Fixed and variable power supply connections via 2-mm
sockets
For use with 2-mm plug-in components
70 nodes each with 9 x 2-mm sockets
7.5-mm grid for 2-mm sockets
4 bus lines for power supply (+15 V,+5 V, -15 V, earth) via 2mm sockets
Variable three-phase power supply
Ergonomic working thanks to console housings
Contact loading: max. 10 A
Dimensions: 358 x 275 x 85 mm (WxDxH)
Weight: 0.5 kg
Additionally recommended
Pos.
Product name
Bestell-Nr.
42 UniTrain storage case for one system
CO4203-2Y
Anz.
1
Sturdy aluminium case with moulded foam block to
accommodate a complete UniTrain system (without equipment)
Capable of accommodating 1 Interface, 2 Experimenters,
1 power supply as well as cables and smaller accessories
Lockable padlock; stable padlock hinge
Colours: aluminium, black, chrome
Dimensions: 610 x 480 x 100 mm
Weight: 4,6 kg
Lucas Nülle GmbH
Page 53/113
www.lucas-nuelle.com
Networking technology TCP/IP
Networking technology TCP/IP
Lucas Nülle GmbH
Page 54/113
www.lucas-nuelle.com
List of articles:
Supplementary Set for SO4204-9Q:
Lucas Nülle GmbH
Page 55/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
43 Course Network technology 1: TCP/IP
SO4204-9Q
Anz.
1
Includes:
1 CD with Labsoft browser and “Network technology” course
1 Experiment card with network client
1 Experiment card with network server
1 Network switch
2 Cat5 connection cables, standard
1 Cat5 connection cable, cross-over
Comprising a network server, network client and related accessories,
the network simulation equipment forms part of the hardware for the
course. It can be integrated into other courses or combined with real
networks as required.
Course Contents:
Explanation of the distinctions between LAN, MAN, WAN, GAN
networks
Introduction to network standards and standards organisation
Introduction to various network topologies
List of advantages and disadvantages of various network
topologies (Ethernet, token ring, token bus)
Introduction to the OSI layer model
Explanation of network components and their function
Introduction to the structure and components of Ethernet
networks
Explanation of the principle of addressing (MAC addresses)
in local networks
Differences between the 10base2 and 10BaseT standards
List of differences between client-server and peer-to-peer
networks
Assembly and testing of a client-server computer network
Assembly and testing of a peer-to-peer computer network
Network ports and their function
Introduction to the internet protocol family TCP/IP
Key differences between IPv4 and IPv6
Explanation of IP addressing
Use of network masks
Changing the network address of a computer in a network
Lucas Nülle GmbH
Page 56/113
www.lucas-nuelle.com
Assembly of a sub-net using a sub-net mask
Course duration: approximately 3.5 hours
44 Course Network Technology 2: Client integration
SO4204-9R
1
Including
1 USB 2.0 Ethernet adapter
1 Cat5 connection cable, 2m/6,5'
1 CD-ROM with Labsoft browser and course software
Course contents:
Integration of a network adapter in a PC
Line side, cable connections
Layer 1, the Manchester code and others ...
Configuration of the network adapter (hardware) in a
Windows XP operating system
Configuration of the network interface and the associated
driver
Integration in an existing network
Use of Tools for checking the function
DHCP
Name detection in Windows networks (host files, WINS)
Using services (http, ftp)
Creating cleardowns (or release for transfer)
Course duration, approximately 3 hours
Lucas Nülle GmbH
Page 57/113
www.lucas-nuelle.com
Additionally required:
The UniTrain-I system is a computer-based training and experimentation system for vocational and further
training and education in the areas of basic and advanced electrical engineering and electronics. Its multimedia
courses combine cognitive and hands-on (haptic) training units into a comprehensive unified concept,
specifically enabling students to acquire skills in the handling of equipment. Starting with basic courses and
advancing to cover a huge variety of electrical engineering and electronics topics, a wide range of multimedia
courses is available for study in school or in professional and advanced training courses. The UniTrain-I system
is completely self-contained and can be used anywhere at any time. The multimedia learning environment the
system provides high degrees of motivation, and maximum learning effectiveness in laboratories, at work or at
home. It thus becomes a guarantor for effective and efficient study. Access to the multimedia courses and
control of virtual instruments and experiment hardware is provided by LabSoft, the system's open experiment
platform. The courses teach the theoretical building blocks and provide experiments to be carried out using the
course-specific experiment hardware. The intelligent measurement interface supplies the analog and digital
measuring and control I/O and represents, in combination with the system's virtual instruments, a high quality
item of laboratory equipment. In addition, students' progress can be monitored and electronically documented on
the basis of fault finding experiments with faults simulated by the hardware as well as tests of knowledge. The
electrical and electronic circuits needed for the experiments are connected to the system with the aid of an
Experimenter module.
Lucas Nülle GmbH
Page 58/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
45 UniTrain Interface with virtual instruments (basic VI)
CO4203-2A
Anz.
1
The UniTrain Interface is the central unit of the UniTrain system. It
incorporates all inputs and outputs, switches, power and signal
sources and measurement circuitry needed to perform experiments.
The Interface is controlled via the connected PC.
Equipment:
32-bit processor with storage memory for measurements
USB interfaces, transfer rate 12 Mbits/s
WLAN/WiFi interface, 2.4 GHz, IEEE 802.11 b/g/n
Simultaneous connection of any number of Experimenters via
serial bus system
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front panel
Suitable for accommodating in training panel frames for DIN
A4 training panels
Designed for connection of 2-mm safety measuring leads
Multi-coloured LEDs for displaying status
Adjustable analog output, +/-10 V, 0.2 A, DC – 5 MHz, via BNC
and 2-mm sockets
4 Analog differential amplifier inputs with 10 MHz band width,
safe for voltages up to 100 V, sampling rate 100 mega
samples, 9 measuring ranges, memory depth 4 x 8 k x 10
bits, inputs via BNC (2 inputs) or 2-mm sockets (4 inputs)
2 Analog inputs for current measurement, overcurrentprotected up to 5 A, sampling rate 250 kilo samples, 2
measuring ranges, resolution 12 bits, connection via 2-mm
sockets
16-bit digital signal output, of which 8 bits are accessed via 2mm sockets, TTL/CMOS, clock frequency 0 – 100 kHz, electric
strength +/- 15 V
16-bit digital signal input, of which 8 bits are accessed via 2mm sockets, memory depth 16 bit x 2 k, TTL/CMOS, sampling
rate 0 – 100 kHz, electric strength +/- 15 V,
8 Relays, 24 V DC/1 A, of which 4 are accessed via 2-mm
sockets
Dimensions: 29.6 x 19 x 8.6 cm
External power supply with wide range input 100-264 V, 47-63
Hz, output 24 V/5 A
Weight (including power supply): 2.1 kg
Virtual instruments (meters and sources):
2 x Voltmeter VIs, 2 x Ammeter VIs: AC, DC, 9 ranges, 100mV
to 50V, true RMS, AV
1 x VI with 8 relays, 1 x Multimeter VI: multimeter display
(optional LM2330, LM2331 or LM2322) in LabSoft
1 x 2-channel ammeter VI: AC, DC, 2 ranges, 300 mA and 3 A,
TrueRMS, AV
1 x 2-channel voltmeter VI: AC, DC, 9 ranges, 100 mV to 50 V,
TrueRMS, AV
1 2-/4-channel oscilloscope: band width 10 MHz, 25 time
ranges, 100 ns/div to 10 s/div, 9 ranges 20 mV/div to 10 V/div,
trigger and pre-trigger, XY and XT modes, cursor function,
addition and multiplication function for 2 channels
1 x Adjustable DC voltage VI 0 - 10 V
1 x Function generator VI: 0.5 Hz - 5 MHz, 0 - 10 V, sine,
square, triangular,
1 x Arbitrary generator VI, 1 x Pulse generator VI
1 x VI with 16 digital outputs, 1 x VI with 16 x digital inputs, 1 x
Lucas Nülle GmbH
Page 59/113
www.lucas-nuelle.com
VI with 16 digital input/outputs. Display modes: binary, hex,
decimal and octal numerals
1 x Three-phase power supply VI, 0 - 150 Hz, 0 - 14 Vrms, 2 A
(requires CO4203-2B)
1 x Adjustable DC power supply VI, 3 x (-20 V - +20 V), 2 A
(requires CO4203-2B)
1 x Three-phase power supply VI with additional phase-shift
and clock rate adjustment (requires CO4203-2B)
Includes:
Interface
Power supply
Power lead
USB cable
CD with basic software
Operating manual
System requirements:
Personal computer with Windows Vista, Windows 7,
Windows 8, Windows 8.1, Windows 10 (32 or 64 bit version)
CD-ROM drive for installing software
USB port for connection to Interface
46 UniTrain Experimenter
CO4203-2B
2
UniTrain Experimenter for coupling to the UniTrain Interface or to
other Experimenter modules.
Equipment:
Connects to the UniTrain Interface and additional
Experimenters via UniTrain bus
UniTrain bus connection for experiment cards
High-quality designer casing with aluminium feet and
surface-hardened Plexiglas front window
Suitable for accommodating training panel frames for DIN A4
training panels
Fixed and variable voltages available via 8 2-mm sockets
Designed for connection of 2-mm safety measuring leads
Accommodates UniTrain experiment cards
Eject mechanism for UniTrain experiment cards with return
spring
Accommodates a breadboard for experimenting with discrete
components and integrated circuits
Accommodates a multimeter using IrDa interface
Dimensions: 29.6 x 19 x 8.6 cm
Weight: 1.0 kg
Lucas Nülle GmbH
Page 60/113
www.lucas-nuelle.com
47 UniTrain-I measurement accessories, shunts and connection
cables
SO4203-2J
1
Shunt resistors on a PCB, for current measurement using the
analog inputs of the UniTrain system.
6 Shunt resistors: 2 x 1 ohm, 2 x 10 ohm, 2 x 100 ohm
Screen print of symbols for identifying resistors, the
voltage taps and current inputs
24 x 2-mm sockets
Dimensions: 100 x 40 mm
Set of connection cables 2mm (22 pcs) for UniTrain consisting
of:
8 x connection leads 2mm, 15cm, blue
4 x connection leads 2mm, 15cm, yellow
2 x connection leads 2mm, 45cm, black
2 x connection leads 2mm, 45cm, yellow
2 x connection leads 2mm, 45cm, red
2 x connection leads 2mm, 45cm, blue
2 x adapter leads 4mm to 2mm, 50cm, white
10 x 2-mm connector plugs / Plug spacing 5mm
Additionally recommended
Pos.
Product name
Bestell-Nr.
48 UniTrain storage case for one system
CO4203-2Y
Anz.
1
Sturdy aluminium case with moulded foam block to
accommodate a complete UniTrain system (without equipment)
Capable of accommodating 1 Interface, 2 Experimenters,
1 power supply as well as cables and smaller accessories
Lockable padlock; stable padlock hinge
Colours: aluminium, black, chrome
Dimensions: 610 x 480 x 100 mm
Weight: 4,6 kg
Lucas Nülle GmbH
Page 61/113
www.lucas-nuelle.com
Radar technology
Radar technology
“Radio detection and ranging” is commonly known by its acronym “radar” and refers to a method of using radio
waves to detect the location and distance of objects by measuring the time it takes the electromagnetic waves
to reflect from the object. Radar has developed from what was initially a purely military application and is
deployed nowadays in air traffic control, coast guard use, traffic monitoring, safety and many related areas.
Active radar equipment mostly provides an image and is usually designed in the form of a pulse radar device.
Primary and secondary radar systems are both common, either passively evaluating the radar echo from a
target, or utilising active transponders on the target objects, which respond to incoming pulses and transmit an
answering signal.
Lucas Nülle GmbH
Page 62/113
www.lucas-nuelle.com
List of articles:
Pos.
Product name
Bestell-Nr.
49 Radar-Trainer
CO3538-6A
Anz.
1
This training system, specially designed for educational
purposes, operates without any hazardous high-frequency
radiation. The principle of a radar system is explained using
authentic measurements. The central component of the training
system is a rotating radar base station with a fan beam antenna.
Echoes from ultrasonic pulses are digitalised and transmitted via
a wireless interface to a computer. The targets are then displayed
on a screen in real time. The secondary radar transponder in the
system supports mode Alpha (identification) and mode Charlie
(altitude). The integrated course explains the functionality and
areas of application of primary and secondary radar system by
means of theoretical content, animated images and interactive
tests of knowledge. The knowledge is then cemented with the
help of numerous illustrative experiments. Thanks to the physical
analogies between UHF radar and ultrasound, the knowledge
gained is directly applicable to radar technology.
Benefits to you
Simple, informative and fascinating experiments
Integration between training program and experiment
platform
Physiologically harmless and usable in any room
No certification needed and no restrictions on usage
Passive radar
Active radar with ID transmission and altitude
measurement
System properties and technical data
Signal to noise ratio > 96 dB
Beam width 17°
Range up to 10 m
Laser pointer
Operating frequency 50 kHz
Rotating antenna base with rugged drive incorporating no
play
Angular resolution 1°
USB port
Rechargeable batteries without memory effect
Includes
Base station
Antenna with integrated sub-module
Antenna mounting
USB controlled rotating base with stepper motor
Active target
Set of passive targets
Accessories
Lucas Nülle GmbH
Page 63/113
www.lucas-nuelle.com
Media:
Pos.
Product name
Bestell-Nr.
50 Interactive Lab Assistant: RADAR
SO2802-1R
Anz.
1
Multimedia experiment software with virtual instruments,
instructions and documentation of results for setting up and
carrying out experiments using the radar training system
CO3538-6A.
Interactive experiment set-ups
Measurements and graphics can be copied to the
experiment instruction pages using drag and drop
Measurement and testing software can be run directly
from the instruction pages
Questions with feedback and evaluation logic for testing
knowledge
Printable document for easy printing of experiment
instructions and solutions
CD-ROM with Labsoft browser and course software
Training contents
Basic principles of radar
Pulse radar
Ultrasonic radar
Acoustic longitudinal waves
Wave equation for ultrasound
Common features between the wave equation for
ultrasound and that for electromagnetic waves
Focusing of outgoing wave
Determination of transmission characteristic
Reflection and transmission at boundary surfaces
Characteristic impedance to sound
Wave impedance
Electromagnetic waves in a medium
Reflection response to ultrasound of various
materials
Quantitative observation of echoes, radar equation
Radar cross section
Constant false alarm rate
Radar equation
CFAR thresholds
Types of radar system
Pulse radar equipment
CW radar
FMCW radar
Distance resolution for pulse radar equipment
Secondary radar
Squawking
Response packets
Transponders
Lucas Nülle GmbH
Page 64/113
www.lucas-nuelle.com
Additionally recommended
Pos.
Product name
Bestell-Nr.
51 Installation Telecommunications
Anz.
LA-T0IN
1
LA-T0TR
1
Single-day commissioning of supplied system, including unpacking,
assembly, fitting and installation as required.
Carried out by qualified electricians
Commissioning of equipment
Testing of safety functions
Function testing and demonstration of supplied system or
laboratory
Handover to max. 2 responsible individuals with handover
report and checklist (copy of delivery docket)
52 Telecommunications training
1 Tag Theorie und Praxis-Schulung für max. 12 Personen an den
gelieferten Trainingssystemen, inklusive:
Durchführung durch Fachkräfte mit speziellen Kenntnissen in
dieser Technik und deren Vermittlung
Individuelle Vorbereitung der Trainer
Erklärung der Theorie zu den Experimenten
Einführen von Sicherheitsregeln
Vorstellung der Labsoft-Kurse oder Experimentieranleitung
Aufbau und Versuchsdurchführungen mit Praxisanteil für die
Teilnehmer
Erarbeiten von speziellen Versuchsreihen
Methodische Schritte zur Unterrichtsgestaltung
Erarbeiten von beispielhaften Versuchsergebnissen
Fehlersuche und –beseitigung innerhalb der Experimente
1 USB-Stick mit Dokumentationen
Durchführungsprotokoll
Lucas Nülle GmbH
Page 65/113
www.lucas-nuelle.com
Professional practice
Professional practice
Professional practice Network Installation
Professional practice Network Installation
Lucas Nülle GmbH
Page 66/113
www.lucas-nuelle.com
TTK 1 VoIP-ISDN-POTS trainer SOHO
TTK 1 VoIP-ISDN-POTS trainer SOHO
The SOHO VoIP-ISDN-POTS training system makes it possible to set up, operate, configure and look for
problems on a small-office or home-office (SOHO) telephone system. The training equipment can either be used
on its own or integrated as part of an existing telephone system.
Customer order: planning and set-up of a SOHO telephone system
Installation and configuration
Putting the system into operation
Installation and configuration of analog devices
Installation and configuration of ISDN devices
Installation and configuration of VoIP devices
Troubleshooting
Handover and instruction of customers
Lucas Nülle GmbH
Page 67/113
www.lucas-nuelle.com
Basic equipment set, consisting of:
Basic equipment set, consisting of:
Pos.
Product name
Bestell-Nr.
53 PBX analog/digital
CO3538-1P
Anz.
1
The digital/analog PABX is an industrial-type device especially
adapted for teaching purposes.
All of the functions of a private branch exchange can be utilised freely
and tailored to suit individual requirements.
Service features:
• 2 digital office lines (1 S0 external; ISDN multi-device/system
connection)
• 1 analog office extension (opt. module)
• 2 digital internal lines (1 S0 internal; for connection of elmeg
system telephones as well as standard ISDN-terminal equipment)
• System telephony with elmeg system telephones
• Max. 6 a/b ports
• CLIP and metering pulses on all ports
• Integrated IP router for Internet access via xDSL or ISDN
• 1 xDSL/WAN Ethernet port (for external xDSL modem)
• 1 LAN interface,10/100 Mbit Fast-Ethernet
• 1 LAN interface USB
Optional extensions with
• Module 2 a/b to expand system up to six analog lines
• POTS module for connection of the T444 to an analog office line
• DSP module 4for direct connection to an SIP provider
Lucas Nülle GmbH
Page 68/113
www.lucas-nuelle.com
54 Universal connecting unit
CO3538-1Q
2
CO3538-1S
1
The universal connection unit is comprised of 2 x ISDN and 2 x
CAT5E junction boxes sockets with terminals extended out to
demonstrate contact assignment. Here, the ISDN junction boxes
are additionally equipped with 2 mm sockets for the 100 Ohm
bus termination resistors.
55 NTBA with the line code 2B1Q
A network termination device for an ISDN basic connection with line
code 2B1Q. The NTBA forms the transition from the two-wire Uk0
interface to the four-wire S0 bus and is connected to the first TAE
terminal or the output of the DSL splitter.
Lucas Nülle GmbH
Page 69/113
www.lucas-nuelle.com
56 Analog telephone
CO3538-1Y
2
CO3538-1U
1
Simple analog telephone that can switch between pulse or tone
dialling.
Last-number redial
Callback
Dimensions: 297 x 115 x 70 mm (HxWxD)
57 DSL splitter
A DSL splitter serves to split the telephone and DSL frequencies,
which are transmitted jointly over one subscriber line.
Lucas Nülle GmbH
Page 70/113
www.lucas-nuelle.com
58 Gigabit Ethernet switch
CO3538-1V
1
CO3538-1X
1
CO3538-1R
1
The switch provided for a networking of up to 5 terminal devices (4
devices with 10/100 MBit/s and 1 device with 10/100/1000 MBit/s).
Data are transmitted to the port of switching system on witch the
device with the corresponding destination adress is connected.
Feauters:
arbitrarily cascadable by using front ports
4096 MAC-adresses storable
autosensing
autonegotiation
autopartitioning
store-and-forward
MDI/MDIx
59 SOHO network with fault simulator
Featuring a typical office network model with fault simulator.
• CAT5E cables
• 2 rooms with single CAT5E junction box
• 2 rooms with double CAT5E junction box
• Server room with a patch panel
• Fault simulator
60 Router with DSL modem and WLAN access point
Lucas Nülle GmbH
Page 71/113
www.lucas-nuelle.com
Supplement to basic set, consisting of:
Supplement to basic set, consisting of:
Pos.
Product name
Bestell-Nr.
61 ISDN system telephone
LM9943
Anz.
1
Highlights:
7-row graphic display, illuminated
5 freely programmable keys with LEDs
7 softkeys and 10 function keys
Land-line SMS with comfort functions
Direct support for Firefly and cordless headsets
Optional extension with answering machine and ancillary
keys
Up to 3 ancillary keys (elmeg T400) can be connected
Direct connection to Up0 interfaces (2-wire ISDN)
Lucas Nülle GmbH
Page 72/113
www.lucas-nuelle.com
62 VoIP telephone with graphic display
LM9940
1
This VoIP phone is suitable for training as well as professional
use - ideal for users who need immediate access to all of their
important information.
The most important features
High-resolution, pivoted graphical display
Large LED (red) for incoming calls
12 programmable function keys with multicolor LEDs
Hands-free
Dual Gigabit Ethernet port
Power over Ethernet
Support for several audio devices
SIP RFC3261
Security: SIPS/SRTP, TLS
STUN, ENUM, NAT, ICE
Codecs: G.711, G.729A, G.723.1, G.722, G.726, GSM
6.10 (full rate)
Multi-language
Lucas Nülle GmbH
Page 73/113
www.lucas-nuelle.com
63 DECT telephone (ISDN)
SO3538-3K
1
This cordless telephone is suitable for connection to an ISDN
multipoint access terminal or an ISDN private exchange in a
telephone system. The telephone utilises the international DECT
(GAP) standard.
It is possible to connect up to 6 cordless handsets to one base
station and to conduct internal calls between these handsets. One
mobile handset can be connected to up to 4 different base stations. It
is possible to set up a configuration for multiple users.
DECT\GAP
Digital ISDN technology
Multi-language menu: German, English, Turkish
Max. range (handset to base station) 50 m
Max. range (handset to base station with no obstacles) 300 m
Dialling by keyboard
Telephone with loudspeaker
SMS capability
Repeat dialling (last 10 numbers)
Menu operation
Volume control
Ring tone setting
Localisation of handset
Call and repeat functions MSN (multiple subscriber numbers)
Number recall capacity: 50 names and numbers
Call memory capacity: 10 numbers
Graphic LCD display (single colour, multi-line)
Receiver display
Integrated antenna
Power supply adapter (external)
2 x batteries (AAA type) (rechargeable)
Battery capacity 750 mAh
Operating duration up to 900 minutes
Stand-by capacity up to 150 hours
Audible battery alarm
Lucas Nülle GmbH
Page 74/113
www.lucas-nuelle.com
64 DECT telephone (analog)
SO3538-3L
1
This cordless telephone is suitable for connection to an analogue
line or private exchange in a telephone system. The telephone
utilises the international DECT (GAP) standard.
It is possible to connect up to 6 mobile handsets to one base station
and to conduct internal calls between these handsets. One mobile
handset can be connected to up to 4 different base stations. The
supplied handset is pre-configured for one base station.
DECT\GAP
Hands-free calling
Illuminated liquid crystal display
Illuminated keyboard
Number recall capacity: 50 names and numbers
Polyphonic call tones: 5 melodies + 5 call tones
Call memory capacity:10 numbers
Automatic redial
Call number display CLIP
Languages (display): German, English, Spanish, French,
Turkish…
Quick dialling
Call sequencing for call-by-call function
Number of handsets supported by each base station: 6
Number of base stations supported by each handset: 4
Batteries: NiMH or NiCD can be used
Stand-by: 180 hours
Operating duration: 17 hours
Lucas Nülle GmbH
Page 75/113
www.lucas-nuelle.com
65 NTBA with the line code 4B3T
CO3538-1T
1
A network termination device for an ISDN basic connection with line
code 4B3T. The NTBA forms the transition from the two-wire Uk0
interface to the four-wire S0 bus and is connected to the first TAE
terminal or the output of the DSL splitter.
Measuring instruments:
Pos.
Product name
Bestell-Nr.
66 SignalTEK II data cable and signal tester
LM9890
Anz.
1
A handheld qualifier to confirm correct copper & fiber cable
installations and active network performance for voice, video, data
and CCTV applications over 10/100 Megabit or Gigabit Ethernet.
• Bi-directional load testing at maximum gigabit data rate
• Advanced Ethernet fault diagnosticis
• Wiring examination per pin and pair of wires
• Informative measurement reports
• Stress testing across switches
Lucas Nülle GmbH
Page 76/113
www.lucas-nuelle.com
Accessories:
Lucas Nülle GmbH
Page 77/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
67 Mobile aluminium experiment stand, 3 levels, power strip with 6
sockets, 1250x700x1995mm
ST7200-3A
Anz.
1
High-quality, mobile experiments stand from the SybaPro range
for demonstrations and experiments. Features aluminium profile
legs compatible with all add-ons and extensions for the SybaPro
system.
The mobile experiment stand is supplied in kit form and needs to
be assembled by customers themselves.
Table top:
30-mm table top made of highly compressed, multi-layer
fine chipboard conforming to DIN EN 438-1
Colour grey, RAL 7035, with 0.8-mm slightly textured
laminate coating (Resopal) on both sides, conforming to
DIN 16926
Resistant to many chemicals and reagents including
dilute acids and alkalis
Resistant to heat, e.g. molten solder or heating at specific
points such as by soldering tips or cigarette ends
Table top with solid impact-resistant protective edging
made of 3mm thick RAL 7047 coloured plastic
Coating and adhesive are PVC free
Power strip with 6 outlet sockets mounted underneath the
table top, lead and earthed plug
Frame:
2 extruded aluminium profiles with multiple grooves 1800 x
120 x 40 mm (WxHxD)
8 equally sized grooves in extruded aluminium profiles (3
on each side and 1 each on the front and back)
Grooves accommodate standard industrial mountings
4 H-shaped aluminium profiles, 1150 mm, for 3-layer
organisation of DIN A4 panels
Space for extension of power supply duct
Base made of rectangular tubing with 4 swivelling double
casters, 2 of which have brakes
Table frame made of tough combination of rectangular
tubing around the full perimeter
Acid-resistant epoxy-resin coating, 80 µm thick (approx.),
colour RAL 7047
Dimensions:
Height of table top 760 mm
1250 x 1995 x 700 mm (WxHxD)
Lucas Nülle GmbH
Page 78/113
www.lucas-nuelle.com
68 Set of safety measurement cables, 2mm (30 leads), for video
intercom
SO5148-1R
1
LM9055
4
LM9057
2
Set of safety measurement leads with stackable 2-mm laminated
plugs and highly flexible, double-insulated leads, consisting of the
following:
4 safety connector leads, 2mm, 30cm, black
10 safety connector leads, 2mm, 30cm, green
6 safety connector leads, 2mm, 30cm, yellow
2 safety connector leads, 2mm, 60cm, green
4 safety connector leads, 2mm, 60cm, black
2 safety connector leads, 2mm, 60cm, red
2 safety connector leads, 2mm, 60cm, yellow
Wire cross section 0.5 mm ²
Rating: 600V, CAT II, 10A
69 Patch cable Cat5E 1x0.5m red, 1x0.5m blue, 1x2.0m yellow
Patch cable set
1 x 0,5 m, color red
1 x 0,5 m, color blue
1 x 2,0 m, color yellow
70 Patch cable Cat5E 1x 1m yellow, 2x 2m yellow
1x 1m yellow
2x 2m yellow
Lucas Nülle GmbH
Page 79/113
www.lucas-nuelle.com
71 USB cable A-B
LM9060
1
USB cable
Media:
Pos.
Product name
Bestell-Nr.
72 Interactive Lab Assistant: Office Telecommunications Network
Installation
SO2802-1G
Anz.
1
Multimedia experiment software with virtual instruments, instructions
and documentation of results for commissioning and configuration
of an office telecommunications network.
Questions with feedback and evaluation logic for monitoring
student progress
Printable document for easy printing of instructions and
solutions
Available in German, English, French and Spanish. Additional
languages available on request
CD-ROM with browser and course software
Training contents:
With this modular panel system it is possible to simulate a complete
office: including commonly used telecommunications systems,
wiring and telephone equipment.
Exercises cover the following topics:
Planning of telecommunications structures
Programming and configuration of an ISDN private branch
exchange
Connection of analog ISDN devices (analog telephones) to a
PBX system
Programming and configuration of ISDN devices (ISDN
telephones).
Lucas Nülle GmbH
Page 80/113
www.lucas-nuelle.com
73 Interactive Lab Assistant "Router"
SO2802-1J
1
SO5157-9X
1
SO5152-9X
1
Multimedia experiment software with virtual instruments,
instructions and documentation of results for set-up and
configuration of a Router with WIFI-Access Point
Interactive experiment set-ups
Measurements and graphics can be stored in the online
instructions via drag and drop
Measurement and testing software can be started straight
from the experiment instructions
Questions with feedback and evaluation logic for testing
knowledge
Printable document so that the experiment instructions
and solutions can be printed easily
CD-ROM with Labsoft browser and course software
Learning objectives:
Function of a Router
Configuration of a Routers
Monitoring
Configuration of a LAN
DHCP-Server
Configuration of a WIFI-Network
SSID
Encryption of WIFI-Connections
74 TPN/TTN, ISDN, LAN and analog installation techniques (GB)
Experiment manual consisting of information for teachers plus
assembly plans
Worksheets for students
Language: English
75 ISDN-, LAN- und analoge Anschlusstechnik mit Einführung
Lichtwellenleiter (D)
Experiment manual consisting of information for teachers plus
assembly plans
Worksheets for students.
Language: German
Lucas Nülle GmbH
Page 81/113
www.lucas-nuelle.com
Additionally recommended
Pos.
Product name
Bestell-Nr.
76 Installation Telecommunications
Anz.
LA-T0IN
1
LA-T0TR
1
Single-day commissioning of supplied system, including unpacking,
assembly, fitting and installation as required.
Carried out by qualified electricians
Commissioning of equipment
Testing of safety functions
Function testing and demonstration of supplied system or
laboratory
Handover to max. 2 responsible individuals with handover
report and checklist (copy of delivery docket)
77 Telecommunications training
1 Tag Theorie und Praxis-Schulung für max. 12 Personen an den
gelieferten Trainingssystemen, inklusive:
Durchführung durch Fachkräfte mit speziellen Kenntnissen in
dieser Technik und deren Vermittlung
Individuelle Vorbereitung der Trainer
Erklärung der Theorie zu den Experimenten
Einführen von Sicherheitsregeln
Vorstellung der Labsoft-Kurse oder Experimentieranleitung
Aufbau und Versuchsdurchführungen mit Praxisanteil für die
Teilnehmer
Erarbeiten von speziellen Versuchsreihen
Methodische Schritte zur Unterrichtsgestaltung
Erarbeiten von beispielhaften Versuchsergebnissen
Fehlersuche und –beseitigung innerhalb der Experimente
1 USB-Stick mit Dokumentationen
Durchführungsprotokoll
Lucas Nülle GmbH
Page 82/113
www.lucas-nuelle.com
TTN 1 Telecommunication Installation Techniques
TTN 1 Telecommunication Installation Techniques
The Telecommunication Installation Techniques are component parts of the training complex "Network
Technology" and includes following topics:
Components in ISDN network installations,
Cable, plugs and sockets, assembly, use and functioning,
Use of hand tools and test instruments in the installation,
Network topologies and the equipment required for their practical application.
Basic equipment set, consisting of:
Basic equipment set, consisting of:
Pos.
Product name
Bestell-Nr.
78 Set of cables, ISDN installation
SO3538-4D
Anz.
1
Cabling set comprising the following items:
1 ISDN patch panel for 24 ports
3 Fully screened double ISDN sockets
100 m of star-quad cable
50 RJ45 plugs for circular cables
Lucas Nülle GmbH
Page 83/113
www.lucas-nuelle.com
79 Set of cables, terminal device installation
SO3538-4E
1
SO3538-4A
1
SO3538-4B
1
Cabling set comprising the following items:
100-m modular ribbon cable, 4-core
100-m modular ribbon cable, 6-core
100-m modular ribbon cable, 8-core
1 set of modular plugs 4-, 6/4-, 6/6-, 8/8-way
80 Mini rack, 19''
The rack is designed for straightforward insertion of 19" components
at the working place. The fixing screws for patch-panel, channel
segment or hub, are included in the supply. Dimensions:
240x490x310 mm (HxWxD) Capacity: 4HU Color: Light-grey
81 Channel segment for19' rack
Anodised aluminium sill-type trunking segment, 105mm wide.
prepared for mounting 3 equipment sockets 3 sockets are included
in the supply. Dimensions: 105x490x66 mm (HxWxD)
Accessories:
Pos.
Product name
Bestell-Nr.
82 Set of tools for Cat5 & telecommunications
SO3538-4H
Anz.
1
Set of tools for Cat5/telecommunications comprises:
Crimping tool for Hirose connector
Crimping tool for modular plugs, 4-, 6- & 8-way
Wire-end stripper for installation cables
LSA-Plus insertion tool
Line tester, incl. battery
Lucas Nülle GmbH
Page 84/113
www.lucas-nuelle.com
Media:
Pos.
Product name
Bestell-Nr.
83 ISDN-, LAN- und analoge Anschlusstechnik mit Einführung
Lichtwellenleiter (D)
Anz.
SO5152-9X
1
SO5157-9X
1
Experiment manual consisting of information for teachers plus
assembly plans
Worksheets for students.
Language: German
84 TPN/TTN, ISDN, LAN and analog installation techniques (GB)
Experiment manual consisting of information for teachers plus
assembly plans
Worksheets for students
Language: English
Lucas Nülle GmbH
Page 85/113
www.lucas-nuelle.com
TPN 1 Cat5 Installation Techniques
TPN 1 Cat5 Installation Techniques
The Cat5 Installation Techniques are component parts of the training complex "Network Technology" and
includes following topics:
Components in Cat5-network installations,
Cable, plugs and sockets, assembly, use and functioning,
Use of hand tools and test instruments in the installation,
Network topologies and the equipment required for their practical application.
Basic equipment set, consisting of:
Basic equipment set, consisting of:
Wenn kein lokales Netzwerk vorhanden ist, empfehlen wir für den Funktionstest folgenden Switch
Pos.
Product name
Bestell-Nr.
85 Set of cables, Cat5
SO3538-4C
Anz.
1
Comprises:
1 Cat5 patch-panel for 16 ports
3 double-sockets Cat5, fully screened
100m Cat5 cable, foil-screened
50 Hirose modular connectors
Lucas Nülle GmbH
Page 86/113
www.lucas-nuelle.com
86 Mini rack, 19''
SO3538-4A
1
SO3538-4B
1
SO3538-4T
1
The rack is designed for straightforward insertion of 19" components
at the working place. The fixing screws for patch-panel, channel
segment or hub, are included in the supply. Dimensions:
240x490x310 mm (HxWxD) Capacity: 4HU Color: Light-grey
87 Channel segment for19' rack
Anodised aluminium sill-type trunking segment, 105mm wide.
prepared for mounting 3 equipment sockets 3 sockets are included
in the supply. Dimensions: 105x490x66 mm (HxWxD)
88 16 Port Switch10 / 100 Mbit in 19' rack housing, 1HU
The 16-port switch features the following options
Applicable for 10-MBit and 100-MBit networks
Integrated switch function
Automatic data rate detection
Integrated power supply
Accessories:
Pos.
Product name
Bestell-Nr.
89 Set of tools for Cat5 & telecommunications
SO3538-4H
Anz.
1
Set of tools for Cat5/telecommunications comprises:
Crimping tool for Hirose connector
Crimping tool for modular plugs, 4-, 6- & 8-way
Wire-end stripper for installation cables
LSA-Plus insertion tool
Line tester, incl. battery
Lucas Nülle GmbH
Page 87/113
www.lucas-nuelle.com
Measuring instruments:
Pos.
Product name
Bestell-Nr.
90 Wiring and network tester NaviTEK II
LM9891
Anz.
1
A versatile wiring and network tester for quick and easy fault finding
and maintenance of both active and passive copper and fibre optic
networks.
Wiring testing per pin and pair of wires
Enhanced Ethernet fault diagnostics
Support for IPv6 and PoE
Informative reports
Compatible with 802.1x standard
Media:
Pos.
Product name
Bestell-Nr.
91 ISDN-, LAN- und analoge Anschlusstechnik mit Einführung
Lichtwellenleiter (D)
SO5152-9X
Anz.
1
Experiment manual consisting of information for teachers plus
assembly plans
Worksheets for students.
Language: German
Lucas Nülle GmbH
Page 88/113
www.lucas-nuelle.com
92 TPN/TTN, ISDN, LAN and analog installation techniques (GB)
SO5157-9X
1
Experiment manual consisting of information for teachers plus
assembly plans
Worksheets for students
Language: English
Professional practice WLAN
Professional practice WLAN
Lucas Nülle GmbH
Page 89/113
www.lucas-nuelle.com
TWT 1 WLAN trainer SOHO
TWT 1 WLAN trainer SOHO
The WLAN SOHO trainer can be used to realize typical network installations for small offices / home offices.
The office computers can be integrated into the network either by means of cables or via WLAN with the help of
accompanying USB sticks. A WLAN repeater makes it possible to optimize range and wireless coverage.
Lucas Nülle GmbH
Page 90/113
www.lucas-nuelle.com
Basic equipment set, consisting of:
Basic equipment set, consisting of:
Pos.
Product name
Bestell-Nr.
93 WLAN training system
SO3538-4Z
Anz.
1
Content of the technical practice includes the training of practical
skills in the installation and protection of wireless networks in small
office and\or home office areas.
This includes selecting the correct components, materials and tools
for installation as well as the knowledge of the encryption to be
implemented.
Delivery includes:
1 x WLAN-Router
DSL-Modem for ADSL/ADSL2+
802.11 n/g/b/a
USB 2.0-port for printer or network storage
iPhone and Android-Smartphones integration is possible
1 x WLAN-Repeater
802.11 n/g/b/a
plug-n-play
WPA2, WPA, WEP
2 x WLAN-USB-Sticks
802.11 n/g/b/a
WPA2 (802.11i)
stick-n-surf
USB2 and USB1.1
Wi-Fi Protected Setup (WPS)
1 x Gigabit Ethernet Switch, 5 ports
5 x Patch cable
Lucas Nülle GmbH
Page 91/113
www.lucas-nuelle.com
Supplement to basic set, consisting of:
Supplement to basic set, consisting of:
Pos.
Product name
Bestell-Nr.
94 Mobile server carriage
ST7200-3E
Anz.
1
Mobile server cabinet for practical projects on the topics of
information technology and telecommunications. The server trolley
has 2 x 19'' drawers and a 19'' rack with earthed mains sockets and
RJ45 sockets. It is also laid out to accommodate additional 19''
racks.
2-level frame
2 folding side pieces
Integrated 5-way socket strip
Laid out to accommodate additional 19'' racks
2 x 19'', 3 HU drawers
19'', 2 HU rack with 2 x mains sockets and 2 x RJ45 sockets
Lucas Nülle GmbH
Page 92/113
www.lucas-nuelle.com
Measuring instruments:
Pos.
Product name
Bestell-Nr.
95 AirCheck Wi-Fi tester
LM9993
Anz.
1
AirCheck is suitable for all Wi-Fi technologies as well as fault
identification, detection of transmission channels, and connection
tests. It enables quick remedy of the most common vulnerabilities of
Wi-Fi, including:
Problems with network coverage
Overload of networks and channels
Radio-frequency interference
Connection problems
Missed access points
Unauthorized access points
Security settings
Client-side problems
The AirCheck Manager software immediately generates reports and
documentation. You can also use it to set up different profiles,
besides managing network and security settings for single device or
a whole series of AirCheck testers.
Features of the AirCheck product:
Supports 802.11a/b/g/n
Turns on within three seconds, and automatically begins
searching for networks, access points (APs) and channel
activity.
At just one or two pushes of a button, an intuitive user
interface provides the answer you are looking for on a bright
colour display.
Detects security settings for each network and access point:
Open, WEP, WPA, WPA2 and/or 802.1x. Indicates the
bandwidth occupied by 802.11 traffic and interference on
individual transmission channels, and the APs which currently
have access to them.
Marks unauthorized APs. The LOCATE function can be used to
detect such APs. An optional directional antenna permits even
faster searching.
Establishes connections to networks or particular APs via
WEP, WPA, WPA2 and / or 802.1x. Determines IP addresses
and sends ping signals.
Lucas Nülle GmbH
Page 93/113
www.lucas-nuelle.com
Media:
Pos.
Product name
Bestell-Nr.
96 Interactive Lab Assistant: Office WIFI
SO2802-1D
Anz.
1
Multimedia experiment software with virtual instruments,
instructions and documentation of results for set-up and
configuration of an office WLAN
Interactive experiment set-ups
Measurements and graphics can be stored in the online
instructions via drag and drop
Measurement and testing software can be started straight
from the experiment instructions
Questions with feedback and evaluation logic for testing
knowledge
Printable document so that the experiment instructions
and solutions can be printed easily
CD-ROM with Labsoft browser and course software
Training topics
Fundamentals of WIFI
WIFI standards and hardware
Access point and Repeater
WIFI planning and survey
WIFI roaming (ESSID / IEEE 802.11f)
Installation and acceptance
WIFI SSID
Encryption and WIFI security
WIFI cell structure
Diagnostics and fault remedy
Fault sources
Interference
Multipath propagation
Trouble-shooting in a WIFI
Lucas Nülle GmbH
Page 94/113
www.lucas-nuelle.com
TWT 2 WLAN radio link trainer Bridgelink
TWT 2 WLAN radio link trainer Bridgelink
Cables are the most common method of connecting computers and peripherals together in a network, but often
not the cheapest and certainly not the most flexible. Especially not if your offices are spread across several
buildings, or if you are using an external warehouse. For some time now, WLAN (wireless local area network)
technology has allowed point-to-point connections to be realized cheaply and easily over long distances.
Basic equipment set, consisting of:
Basic equipment set, consisting of:
Pos.
Product name
Bestell-Nr.
97 WLAN bridge link training system
SO3538-4F
Anz.
1
The WLAN-Bridge link trainer consists of:
2 x WLAN-access point (802.11agbhn, dual-band 2.4 GHz
and 5 GHz, VPN, PoE)
2 x dual polarized antenna (802.11n, 5GHz, 20dBi)
4 x cable CAB-RSMA-N 0,5 m
2 x Ethernet PoE switch 8 ports 10/100 RJ45
10 x Patch cable
2 x Support small
2 x Support big
2 x Bracket
Lucas Nülle GmbH
Page 95/113
www.lucas-nuelle.com
Measuring instruments:
Pos.
Product name
Bestell-Nr.
98 AirCheck Wi-Fi tester
LM9993
Anz.
1
AirCheck is suitable for all Wi-Fi technologies as well as fault
identification, detection of transmission channels, and connection
tests. It enables quick remedy of the most common vulnerabilities of
Wi-Fi, including:
Problems with network coverage
Overload of networks and channels
Radio-frequency interference
Connection problems
Missed access points
Unauthorized access points
Security settings
Client-side problems
The AirCheck Manager software immediately generates reports and
documentation. You can also use it to set up different profiles,
besides managing network and security settings for single device or
a whole series of AirCheck testers.
Features of the AirCheck product:
Supports 802.11a/b/g/n
Turns on within three seconds, and automatically begins
searching for networks, access points (APs) and channel
activity.
At just one or two pushes of a button, an intuitive user
interface provides the answer you are looking for on a bright
colour display.
Detects security settings for each network and access point:
Open, WEP, WPA, WPA2 and/or 802.1x. Indicates the
bandwidth occupied by 802.11 traffic and interference on
individual transmission channels, and the APs which currently
have access to them.
Marks unauthorized APs. The LOCATE function can be used to
detect such APs. An optional directional antenna permits even
faster searching.
Establishes connections to networks or particular APs via
WEP, WPA, WPA2 and / or 802.1x. Determines IP addresses
and sends ping signals.
Lucas Nülle GmbH
Page 96/113
www.lucas-nuelle.com
Media:
Pos.
Product name
Bestell-Nr.
99 Interactive Lab Assistant: Directional WLAN - Bridgelink training
system
SO2802-1E
Anz.
1
Multimedia experiment software with virtual instruments, instructions
and documentation of results for set-up and configuration of a WLAN
bridge
Interactive experiment set-ups
Measurements and graphics can be stored in the online
instructions via drag and drop
Measurement and testing software can be started straight
from the experiment instructions
Questions with feedback and evaluation logic for testing
knowledge
Printable document so that the experiment instructions and
solutions can be printed easily
CD-ROM with Labsoft browser and course software
Lucas Nülle GmbH
Page 97/113
www.lucas-nuelle.com
Professional practice VoIP
Professional practice VoIP
The Internet has achieved the status of the “people’s network”. The plan to use it for telephony is now not far
away. The result is Internet protocol telephony or VoIP, a technology that makes it possible to use IP
infrastructure for telephone service and in turn, replace the traditional telephone technology.
TVP1 VoIP-Trainer Lite
TVP1 VoIP-Trainer Lite
Lucas Nülle GmbH
Page 98/113
www.lucas-nuelle.com
List of articles:
Pos.
Product name
Bestell-Nr.
100 VoIP Lite training system
SO3538-4W
Anz.
1
VOIP-Trainer Lite is a software PBX-based training system,
which incorporates all of the functionality of a conventional
telephone system. The system supports VoIP with a range of
various protocols (SIP, AIX, H.323, UNIStim and SCCP) and can
be used in conjunction with the VoIP-Trainer Pro. The Soft PBX
system operates virtually. Up to 4 VoIP terminal devices and
(theoretically) any number of soft phones can be connected and
operated simultaneously.
Minimum requirements for the PC on which the VoIP-Trainer Lite
is installed on:
• 1024 MB main memory
• 20 GB free space on the hard disk
• Dual-core processor or minimum 2.4 GHz fast single-core.
• Ethernet or USB port
• Win XP, 7, 8, 10 or Linux
Lucas Nülle GmbH
Page 99/113
www.lucas-nuelle.com
Media:
Pos.
Product name
Bestell-Nr.
101 Interactive Lab Assistant: "VOIP LITE"
SO2802-1L
Anz.
1
Multimedia experiment software with virtual instruments, instructions
and documentation of results for commissioning and configuration
of a VoIP PBX system.
Interactive experiment set-up
Questions with feedback and evaluation logic for testing
knowledge
Printable document so that experiment instructions with
answers can be printed easily
CD-ROM with Labsoft browser and course software
Learning objectives:
What is "Voice over Internet Protocol"?
Fundamentals of TCP/IP
Overview of IPv4 and IPv6
Addressing
Masking
Operation of VoIP
VoIP with a conventional PBX system
VoIP appliances
Experiments
Fundamentals of virtualisation
VoIP server
Commissioning of a VoIP PBX system
Virtual PBX systems
Remote access to a virtual PBX system
Upgrading a PBX system
Virtual PBX system/extensions
Hardware versus software solutions
Hardphones
Firmware updates
Reset
Identity
PCAP trace
Softphones
Installation
Configuration
Protocols
SIP
RTP
RTCP
RTSP
IAX
Codecs and voice quality
Codecs
Voice (sound) quality
Interconnection of multiple PBX systems
SIP trunking
External connections (outbound routes)
Allocation of call numbers
Lucas Nülle GmbH
Page 100/113
www.lucas-nuelle.com
Additionally recommended
Pos.
Product name
Bestell-Nr.
102 Installation Telecommunications
Anz.
LA-T0IN
1
LA-T0TR
1
Single-day commissioning of supplied system, including unpacking,
assembly, fitting and installation as required.
Carried out by qualified electricians
Commissioning of equipment
Testing of safety functions
Function testing and demonstration of supplied system or
laboratory
Handover to max. 2 responsible individuals with handover
report and checklist (copy of delivery docket)
103 Telecommunications training
1 Tag Theorie und Praxis-Schulung für max. 12 Personen an den
gelieferten Trainingssystemen, inklusive:
Durchführung durch Fachkräfte mit speziellen Kenntnissen in
dieser Technik und deren Vermittlung
Individuelle Vorbereitung der Trainer
Erklärung der Theorie zu den Experimenten
Einführen von Sicherheitsregeln
Vorstellung der Labsoft-Kurse oder Experimentieranleitung
Aufbau und Versuchsdurchführungen mit Praxisanteil für die
Teilnehmer
Erarbeiten von speziellen Versuchsreihen
Methodische Schritte zur Unterrichtsgestaltung
Erarbeiten von beispielhaften Versuchsergebnissen
Fehlersuche und –beseitigung innerhalb der Experimente
1 USB-Stick mit Dokumentationen
Durchführungsprotokoll
Lucas Nülle GmbH
Page 101/113
www.lucas-nuelle.com
TVP 2 VoIP-ISDN-POTS trainer PRO Monolyth
Lucas Nülle GmbH
Page 102/113
www.lucas-nuelle.com
TVP 2 VoIP-ISDN-POTS trainer PRO Monolyth
This modular training system allows a perfect integration of telecommunications technology into education labs.
Up to 20 groups (virtual VoIP telecommunication PBX) can conduct their projects simultaneously using the
system. The basic equipment consists of a 19" VoIP server and a 19" PBX. If required, a Fast Ethernet switch
and patch panels can be ordered to connect the internal lab telecommunications network. Conventional patch
cables can be flexibly routed to achieve structured cabling for analog and digital laboratory communication. Two
different approaches are possible: Setting up a VoIP private branch exchange with just an Ethernet
infrastructure, or continued use of an existing ISDN or POTS infrastructure with smooth migration to VoIP
technology.
Scalable 19" server with 64-bit operating system and advanced virtualization software.
Simultaneous operation of up to 20 virtual, software-based private branch exchanges.
Conventional VoIP-ISDN-POTS PBX in a 19" rack format.
Connection and commutation technology for autonomous operation and seamless integration into
existent networks.
The following projects can be implemented with this equipment:
1. Customer order: Planning and establishment of enterprise infrastructure.
Commissioning of a VoIP PBX.
Installation and configuration of additional modules: Answering machine, IVR, CLIP, CLIR, Musicon-Hold, conference etc.
Installation and configuration of VoIP terminal devices.
Handover and briefing.
2. Customer order: Planning and setup of a VoIP PBX for several decentral locations.
3. Assembly project: Installation of a network comprising several private branch exchanges.
4. Customer order: Commissioning of a conventional PBX.
Configuration of an ISDN network with up to 32 subscribers.
Configuration of an analog network with up to 16 subscribers.
5. Customer order: Migration from analog and ISDN telephony to VoIP.
Lucas Nülle GmbH
Page 103/113
www.lucas-nuelle.com
Basic equipment set, consisting of:
Basic equipment set, consisting of:
Pos.
Product name
Bestell-Nr.
104 VoIP PRO training system
SO3538-4X
Anz.
1
An extraordinarily flexible training system with boundless capabilities!
The training system is delivered in a mobile, electromagneticallycompliant 19" rack accommodating 15 height units and furnished
with robust and convenient lockers.
The 19" VoIP server's basic version includes the following features:
VoIP with various protocols (SIP, AIX, H.323, UNIStim, SCCP).
Configurable and extensible as required; also connectable
via relatively economical hardware with connections such as
POTS (for analog telephones), ISDN basic rate interface (BRI)
or primary multiplex (PRI, E1 or T1).
Theoretically unlimited number of subscribers.
Covers all functions of a conventional telephony system.
Upgradeable with UMTS, GSM, ISDN und POTS interfaces by
means of optional hardware.
The 19" PBX's basic version includes the following features:
Up to 2 exchange lines.
Up to 2 internal digital channels for ISDN terminal devices or
system telephones.
Connection of up to 8 analog telephones, cordless phones,
fax machines, answering machines or modems.
Two module slots allow expansion to 8 further S0-terminals
or 16 further analog ports.
Windows manager for supporting system configuration.
Upgradeable with DECT and VoIP interfaces by means of
optional hardware.
A professional 19 "module provides a robust solution for training
network technicians and fitters. The module comprises one ISDN
and one CAT5e patch panel.
Lucas Nülle GmbH
Page 104/113
www.lucas-nuelle.com
Supplement to basic set, consisting of:
Supplement to basic set, consisting of:
Pos.
Product name
Bestell-Nr.
Anz.
105 Set of cables, Cat5
SO3538-4C
1
LM9943
1
Comprises:
1 Cat5 patch-panel for 16 ports
3 double-sockets Cat5, fully screened
100m Cat5 cable, foil-screened
50 Hirose modular connectors
106 ISDN system telephone
Highlights:
7-row graphic display, illuminated
5 freely programmable keys with LEDs
7 softkeys and 10 function keys
Land-line SMS with comfort functions
Direct support for Firefly and cordless headsets
Optional extension with answering machine and ancillary
keys
Up to 3 ancillary keys (elmeg T400) can be connected
Direct connection to Up0 interfaces (2-wire ISDN)
Lucas Nülle GmbH
Page 105/113
www.lucas-nuelle.com
107 VoIP telephone with graphic display
LM9940
1
LM9942
1
This VoIP phone is suitable for training as well as professional
use - ideal for users who need immediate access to all of their
important information.
The most important features
High-resolution, pivoted graphical display
Large LED (red) for incoming calls
12 programmable function keys with multicolor LEDs
Hands-free
Dual Gigabit Ethernet port
Power over Ethernet
Support for several audio devices
SIP RFC3261
Security: SIPS/SRTP, TLS
STUN, ENUM, NAT, ICE
Codecs: G.711, G.729A, G.723.1, G.722, G.726, GSM
6.10 (full rate)
Multi-language
108 Analog telephone
This analog table-top telephone is more than a regular terminal
device – the high-quality exterior, its ergonomic use and convenience
functions make this unit your first choice.
The ergonomic location of the handset – fixed securely in
place by a magnet when idle – and the easily readable, threeline alphanumeric display make using this unit pure joy.
Thanks to CLIP, the numbers of incoming calls are shown on
the display. Calls not taken are signalled by LEDs and put into
a caller list, with number, date and time. The call-back
function lets you initiate return calls conveniently at the push
of a button.
Ideal for frequent callers: A separate 3.5 mm jack lets you
connect standard headsets to your system, allowing you to
keep your hands free to do other activities while you make
calls.
Lucas Nülle GmbH
Page 106/113
www.lucas-nuelle.com
109 DECT telephone (ISDN)
SO3538-3K
1
This cordless telephone is suitable for connection to an ISDN
multipoint access terminal or an ISDN private exchange in a
telephone system. The telephone utilises the international DECT
(GAP) standard.
It is possible to connect up to 6 cordless handsets to one base
station and to conduct internal calls between these handsets. One
mobile handset can be connected to up to 4 different base stations. It
is possible to set up a configuration for multiple users.
DECT\GAP
Digital ISDN technology
Multi-language menu: German, English, Turkish
Max. range (handset to base station) 50 m
Max. range (handset to base station with no obstacles) 300 m
Dialling by keyboard
Telephone with loudspeaker
SMS capability
Repeat dialling (last 10 numbers)
Menu operation
Volume control
Ring tone setting
Localisation of handset
Call and repeat functions MSN (multiple subscriber numbers)
Number recall capacity: 50 names and numbers
Call memory capacity: 10 numbers
Graphic LCD display (single colour, multi-line)
Receiver display
Integrated antenna
Power supply adapter (external)
2 x batteries (AAA type) (rechargeable)
Battery capacity 750 mAh
Operating duration up to 900 minutes
Stand-by capacity up to 150 hours
Audible battery alarm
Lucas Nülle GmbH
Page 107/113
www.lucas-nuelle.com
110 DECT telephone (analog)
SO3538-3L
1
LM9928
1
This cordless telephone is suitable for connection to an analogue
line or private exchange in a telephone system. The telephone
utilises the international DECT (GAP) standard.
It is possible to connect up to 6 mobile handsets to one base station
and to conduct internal calls between these handsets. One mobile
handset can be connected to up to 4 different base stations. The
supplied handset is pre-configured for one base station.
DECT\GAP
Hands-free calling
Illuminated liquid crystal display
Illuminated keyboard
Number recall capacity: 50 names and numbers
Polyphonic call tones: 5 melodies + 5 call tones
Call memory capacity:10 numbers
Automatic redial
Call number display CLIP
Languages (display): German, English, Spanish, French,
Turkish…
Quick dialling
Call sequencing for call-by-call function
Number of handsets supported by each base station: 6
Number of base stations supported by each handset: 4
Batteries: NiMH or NiCD can be used
Stand-by: 180 hours
Operating duration: 17 hours
111 Headset, 2x3,5mm Stecker
Stereo Headset with Micorphone
Microphone sensitivity: -44 +/- 3dB
Microphone mute: yes
Device interface: 2x3.5mm (1/8")
Headphone frequency: 20Hz - 20KHz
Impedance: 32Ohm +/- 15%
Cable length: 1.8m
Lucas Nülle GmbH
Page 108/113
www.lucas-nuelle.com
Measuring instruments:
Pos.
Product name
Bestell-Nr.
112 SignalTEK II data cable and signal tester
Anz.
LM9890
1
SO3538-4R
1
A handheld qualifier to confirm correct copper & fiber cable
installations and active network performance for voice, video, data
and CCTV applications over 10/100 Megabit or Gigabit Ethernet.
• Bi-directional load testing at maximum gigabit data rate
• Advanced Ethernet fault diagnosticis
• Wiring examination per pin and pair of wires
• Informative measurement reports
• Stress testing across switches
113 Hand-held test unit for analog telephones
The hand-held test unit can be used for all kinds of measurements
and troubleshooting on analogue phone lines. It is easy to use due
to its clear menus, function keys, a voice function and multi-function
display.
Testing of analogue trunk line interfaces
Testing of analogue interfaces inside PBX systems
Testing polarity
Dialling by pulse or DTMF
Detection of ISDN lines in telecommunications distribution
systems
Switching with no batteries (permanent availability)
CLIP
Display of charges
Weight: 370 g
Current limitation for direct connection to feed voltage up to 80
V DC
Loop current: 15..60 mA
Lucas Nülle GmbH
Page 109/113
www.lucas-nuelle.com
Accessories:
Pos.
Product name
Bestell-Nr.
114 Set of tools for Cat5 & telecommunications
SO3538-4H
Anz.
1
Set of tools for Cat5/telecommunications comprises:
Crimping tool for Hirose connector
Crimping tool for modular plugs, 4-, 6- & 8-way
Wire-end stripper for installation cables
LSA-Plus insertion tool
Line tester, incl. battery
Lucas Nülle GmbH
Page 110/113
www.lucas-nuelle.com
Media:
Lucas Nülle GmbH
Page 111/113
www.lucas-nuelle.com
Pos.
Product name
Bestell-Nr.
115 Interactive Lab Assistant: "VOIP PRO"
SO2802-1K
Anz.
1
Multimedia experiment software with virtual instruments, instructions
and documentation of results for commissioning and configuration
of a VoIP PBX system.
Interactive experiment set-up
Questions with feedback and evaluation logic for testing
knowledge
Printable document so that experiment instructions with
answers can be printed easily
CD-ROM with Labsoft browser and course software
Learning objectives
What is "Voice over Internet Protocol"?
Fundamentals of TCP/IP
Overview of IPv4 and IPv6
Addressing
Masking
Operation of VoIP
VoIP with a conventional PBX system
VoIP appliances
Experiments
ISDN-POTS training system with VoIP gateway
Fundamentals of virtualisation
Multimaster VoIP server
Commissioning of a VoIP PBX system
Conventional PBX system
Installed modules
Configuration of VoIP VPN gateways
Conventional PBX system/extensions
Virtual PBX systems
Remote access to a virtual PBX system
Upgrading a PBX system
Virtual PBX system/extensions
Hardware versus software solutions
Hardphones
Firmware updates
Reset
Identity
PCAP trace
Softphones
Installation
Configuration
Protocols
SIP
RTP
RTCP
RTSP
IAX
Codecs and voice quality
Codecs
Voice (sound) quality
"Smooth migration" to VoIP
Switching from a conventional VoIP PBX system to a
modern one
Integrating conventional and VoIP PBX systems
Lucas Nülle GmbH
Page 112/113
www.lucas-nuelle.com
Additionally recommended
Pos.
Product name
Bestell-Nr.
116 Installation Telecommunications
Anz.
LA-T0IN
1
LA-T0TR
1
Single-day commissioning of supplied system, including unpacking,
assembly, fitting and installation as required.
Carried out by qualified electricians
Commissioning of equipment
Testing of safety functions
Function testing and demonstration of supplied system or
laboratory
Handover to max. 2 responsible individuals with handover
report and checklist (copy of delivery docket)
117 Telecommunications training
1 Tag Theorie und Praxis-Schulung für max. 12 Personen an den
gelieferten Trainingssystemen, inklusive:
Durchführung durch Fachkräfte mit speziellen Kenntnissen in
dieser Technik und deren Vermittlung
Individuelle Vorbereitung der Trainer
Erklärung der Theorie zu den Experimenten
Einführen von Sicherheitsregeln
Vorstellung der Labsoft-Kurse oder Experimentieranleitung
Aufbau und Versuchsdurchführungen mit Praxisanteil für die
Teilnehmer
Erarbeiten von speziellen Versuchsreihen
Methodische Schritte zur Unterrichtsgestaltung
Erarbeiten von beispielhaften Versuchsergebnissen
Fehlersuche und –beseitigung innerhalb der Experimente
1 USB-Stick mit Dokumentationen
Durchführungsprotokoll
Lucas Nülle GmbH
Page 113/113
www.lucas-nuelle.com