84-9756 7/23/98 4:14 AM Page 1 ® A THERMADYNE® Company FABRICATOR SINGLE PHASE 300 AMPERE CONSTANT VOLTAGE POWER SOURCE ® The Thermal Arc FABRICATOR is exceptionally versatile single phase constant voltage power source. The FABRICATOR allows solid wire short circuit, globular and spray transfer welding and flux cored wire in globular or spray transfer modes. The unit is 300 Amp, 60% duty cycle and is NEMA EW-1, CSA approved. A standard 19-pin amphenol connector and dual auxiliary power outlets permit the use of Model 17A, Porta-Feed® 17A, 2210, and 2410 Thermal Arc wire feeders. The FABRICATOR offers a total of 36 voltage steps, through four coarse positions and nine fine positions at approximately .6 Volt per step. This provides precise control for both solid and flux cored wire applications. MORE POWER TO YOU TM 84-9756 7/23/98 4:14 AM Page 2 FABRICATOR SINGLE PHASE 300 AMPERE CONSTANT VOLTAGE POWER SOURCE ® SPECIFICATIONS • • • • OUTPUT RATING 200/230/460/575 Welding Amps 300 375 Volts 32 34 Duty Cycle 60% 40% WELD VOLTAGE RANGE Minimum 40 Amps @ 15 Volts Maximum 375 Amps @ 34 Volts Voltage Steps 36 (4 coarse, 9 fine) Approximately .6 Volt per step MAXIMUM OPEN CIRCUIT VOLTAGE 60 Volts AUXILIARY POWER DUPLEX RECEPTACLE 6 AMPS, 115 VAC (for wire feeder) INPUT RATING 300 amps, @ 32 volts Line Voltage (VAC) . . . .200 230 460 575 Line Amps at Rated Load . . . . . . .77.5 70.2 34 27 Line Amps at at no load . . . . . . . . .4.4 7.2 3.2 2.6 Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Hertz . . . . . . . . . . . . . . . . . . . . . . . . .50/60 KVA . . . . . . . . . . . . . . . . . . . . . . . . . . .16.1 Power Factor At Rated Load . . . . . . . .84% Efficiency at rated load . . . . . . . . . . . .70% DIMENSIONS Length . . . . . . . . . . . . . . . . . . . . . . . . . .26-9⁄16" (67.8 cm) Width . . . . . . . . . . . . . . . . . . . . . . . . . . .16-3⁄4" (42.5 cm) Height with lifting eye . . . . . . . . . . . . . .30-1⁄4" (76.8 cm) Weight . . . . . . . . . . . . . . . . . . . . . . . . .265 lbs. (120 kg) APPROVALS . . . . . . . . . . . . . . . . . . . . . . .CSA, NEMA EW-1 Both Volt and Amp meters are standard Off/ on switch for safety Fuse for additional safety Power supply conveniently located on front of unit. AVAILABLE FILLER METALS The high quality line of Thermal Arc filler metals meet a wide variety of application needs. Please contact Customer Service for more detailed information. www.thermalarc.com www.thermadyne.com ORDERING INFORMATION A. Fabricator Power source 200 / 230 / 460 / 575 volts, 50/60 Hz, SP 7028B-001 B. Wire Feeder compatibility: Model 17A, Porta-Feed® 17A, 2210, 2410 C. Portable mounting with bottle rack 203147-001 D. Optional field installed fan thermostat kit 200155A WORLD HEADQUARTERS: 101 S. Hanley Road • St. Louis, MO 63105 • 314-721-5573 • FAX 314-746-2161 U.S. CUSTOMER SERVICE: 2200 Corporate Drive • Troy, OH 45373 800-255-5846 • FAX 800-332-0946 ® International Customer Service Oakville, Canada Ph: (1) 905-827-9777 Fax: (1) 905-827-9797 International Offices Thermadyne Canada Oakville, Canada Ph: (1) 905-827-1111 Fax: (1) 905-827-3648 Thermadyne do Brasil Sao Paulo, Brazil Ph: (55) 11-744-3444 Fax: (55) 11-453-2260 Form No. 84-9756 Thermadyne Europe Lancashire, England Ph: (44) 1257-261755 Fax: (44) 1257-261756 Thermadyne Middle East Dubai, United Arab Emirates Ph: (971) 4-632-400 Fax: (971) 4-631-781 © Thermal Arc Inc., 1998 Thermadyne Asia Sdn. Bhd. Kuala Lumpur, Malaysia Ph: (60) 3-791-0086 Fax: (60) 3-791-0129 Thermadyne de Mexico Mexico City, Mexico Ph: (52) 5696-7407 Fax: (52) 5696-7757 www.thermalarc.com Cigweld Australia Melbourne, Australia Ph: (61) 3-9487-1234 Fax: (61) 3-9487-1487 Thermadyne Japan Osaka, Japan Ph: (81) 726-303-577 Fax: (81) 726-378-796 Printed in U.S.A.